KANSAI PAINT KANSAI CONDUCOAT 209 WB

Anti-Static Epoxy Undercoat

PRODUCT NAME : KANSAI CONDUCOAT 209 WB

DESCRIPTION : KANSAI CONDUCOAT 209 WB is a two-component water-borne epoxy anti-static

coating suitable for application over concrete, mortar, masonry, asbestos, bricks and

metal surfaces.

RECOMMENDED USE : KANSAI CONDUCOAT 209 WB is used as an undercoat for conductive and anti-static

topcoats, it is suitable for wall and floor of industrial or commercial locations where an

anti-static environment is required. It is most recommended for interior surfaces of clean

rooms, electronic factories, hospital, computer room, printing factories, pharmaceutical

factories and other factories and locations dealing with inflammable gases or liquids.

Not suitable for continuous immersion in solvents and strong acids.

PERFORMANCE : • No odour - application works can be carried out without complete

• No fire hazard - can be used in areas where solvent-based coatings are

• Superior anti-static properties and not affected by ageing.

• Prevents static electric destruction of sensitive components.

• Excellent adhesion to concrete and masonry surfaces.

• Good resistance against mild chemicals.

• Easy to clean - application tools and equipment can be cleaned easily with
water after use.

• Environmental friendly - Zero VOC content.

PHYSICAL PROPERTIES

FINISH Matt

COLOUR Black

VOLUME SOLID 35 %

NO. OF COMPONENTS Two

MIXING RATIO 4 part of A to 1 part of B by weight

RECOMMENDED 50 microns DFT per coat

THICKNESS 83 microns WFT per coat

THEORETICAL COVERAGE 6 to 7 m² / kg for concrete surfaces

NO. OF COATS One coat

RECOMMENDED

TOP COATING TIME Minimum : 8 hours.

Maximum : 48 hours.

PACKING SIZE Part A – 4 kg

Date Issued: November 2016 Page 1 of 2

This Technical Data Sheet supersedes those previously issued

SURFACE RESISTANCE 10² to 103 ohms

SURFACE PREPARATION The surface to be coated must be thoroughly cleaned and degreased to ensure that oil,

grease and other surface contaminants are removed. Surface dust must be removed

using industrial vacuum cleaner. Fins and protrusions shall be removed by stoning,

sanding or grinding. New concrete shall be allowed to cure for at least 28 days before

application of KANSAI CONDUCOAT 209 WB

PRIMER KANSAI CONDUCOAT 209 WB can be applied by using roller. Make sure that the

required thickness is achieved to ensure good anti-static properties.

MIXING Stir Part A and Part B thoroughly in their own containers with power mixer, then pour Part

B into Part A in the pre-weighed packing and continue to stir. Mix to a uniform consistency
before thinning.

THINNING Thin not more than 10% with clean water for workability.

CURING In order for the water in the coated film to be released quickly, coated areas must be well

ventilated. Coated surface can be open for foot traffic after 24 hours. With good

ventilation, topcoats can be applied after 6 to 8 hours.

CLEANING All application tools and equipment can be cleaned with water and detergent after use.

For further information on Product Data, please contact

Protective Coatings Sales Department

Kansai Paint Asia Pacific Sdn Bhd. (705919-W)

DSCLAIMER :

The information in this sheet is provided to the best of our knowledge based on laboratory testing and practical experience. However, as the product is often used under conditions
beyond the manufacturer's control, it is the sole responsibility of the buyer to obtain confirmation from the manufacturer on the suitability of the product for the intended use. Therefore, the
manufacturer
can accept no liability for the performance of the product, or any loss or damage arising out of such use. The information detailed in this data sheet is subject to change without notice in
light of experience and of normal product development.

Date Issued: November 2016 Page 2 of 2

This Technical Data Sheet supersedes those previously issued