8 7 6 5 4 3 2 1

REVISION
ZONE REV DESCRIPTION NAME APPROVED

D D

105 106

C 105
C

107. RELAY CONTACTS RATED: MAX 5A; MAX 30V.

4X Ø0.15
106 USE A 1.3mm²(16AWG) OR LARGER GAUGE WIRE AND A RING TERMINAL
(CORRESPONDS TO #8 SCREW). USE 2 STAR WASHERS, ONE IS PLACED
BETWEEN THE SCREW AND RING TERMINAL, ANOTHER IS BETWEEN THE 104
THE RING TERMINAL AND CHASSIS.
TIGHTEN THE GROUND SCREW WITH 8 IN-LBS +/- 1 IN-LBS TORQUE. GRAVITY

105 GROUNDING (NON-HAZARDOUS AREA INSTALLATION)

WHEN SYSTEM NOT INSTALLED OR INTERFACING TO A HAZARDOUS AREA, A
SINGLE POINT GROUND IS RECOMMENDED TO MINIMIZE GROUND LOOP NOISE.
CONNECT GROUNDING CONDUCTOR AT THE PROTECTIVE EARTH TERMINAL.
B CLOSE THE JUMPER BETWEEN SYSTEM COMMON (COM) AND PROTECTIVE EARTH .
(6.0)
B
GROUNDING (HAZARDOUS AREA INSTALLATION W/ EXTERNAL ZENER BARRIERS)
WHEN EXTERNAL BARRIER ARE IN USE, CONNECT THE SYSTEM COMMON (COM)
WITH THE EARTH OF BARRIER. AND THE PROTECTIVE EARTH CONDUCTOR
MUST BE CONNECTED AT THE PROTECTIVE EARTH TERMINAL. THE JUMPER
BETWEEN SYSTEM COMMON (COM) AND PROTECTIVE EARTH MUST BE OPEN.
SEE PAGE 11 FOR ISOLATION REQUIREMENTS.
GROUNDING (HAZARDOUS AREA INSTALLATION W/ I.S. [ic] OUTPUTS)
WHEN USING SYSTEM I.S. [ic] OUTPUTS TO A ZONE2/DIV.2 AREA, GROUNDING
CONDUCTOR CONNECT INSTRUMENT GROUND TO THE SYSTEM COMMON (COM)
TERMINAL. THE PROTECTIVE EARTH CONDUCTOR MUST BE CONNECTED AT THE
PROTECTIVE EARTH TERMINAL. THE JUMPER BETWEEN SYSTEM COMMON (COM) (5.8)
AND PROTECTIVE EARTH MUST BE OPEN. SEE PAGE 11 FOR ISOLATION (2.7)
REQUIREMENTS.

104 BASE MUST BE MOUNTED AS SHOWN RELATIVE TO GRAVITY. NO CHANGES TO THIS DRAWING WITHOUT
APPROVAL OF THE APPROVALS AGENCIES.
103. MECHANICAL VIBRATION SHALL NOT EXCEED 5g @ 57-500Hz. UNCONTROLLED WHEN PRINTED OR TRANSMITTED ELECTRONICALLY.

A MECHANICAL SHOCK SHALL NOT EXCEED 15g, 11 msec.

A
GE CLASS II (INTERNAL)
Copyright 2014 Baker Hughes, a GE company, LLC (“BHGE”) (unpublished work). 
All rights reserved.  The information contained in this document is confidential
and proprietary property of BHGE and its affiliates.  It is to be used only for the
benefit of BHGE and may not be distributed, transmitted, reproduced, altered or
102. OPERATING TEMPERATURE RANGE: -30 TO +65°C used for any purpose without the express written consent of BHGE.

STORAGE TEMPERATURE RANGE: -40 TO +85°C UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES.
Bently Nevada™ Asset Condition Monitoring
125
HUMIDITY RANGE: 5 TO 95%, NON-CONDENSING FINISHED MACHINED SURFACES

ANGULAR ±
2300 VIBRATION MONITOR
FRACTIONAL ± FIELD WIRING DIAGRAM
101. DIAGRAM IS FOR THE 2300 MONITOR SYSTEMS. DECIMAL .XX= ±
.XXX= ±
0.02
0.010

NAME APPROVED CAGE CODE SIZE NUMBER

NOTES: UNLESS OTHERWISE SPECIFIED
YM CHENG YM CHENG
PLOT SCALE NONE SHEET 1 OF 11
3WAP1 D 106M5801
8 7 6 5 4 3
CDA/106M5801/000/09
2 1
 8 7 6 5 4 3 2 1
REVISION

SEE SHEET 1
TABLE 2A
RELAY OUTPUT WIRING CHART
2300 CONTACT DESCRIPTION
NO1 RELAY 1 - NORMALLY OPEN
ARM RELAY 1 - COM
D NC1 RELAY 1 - NORMALLY CLOSE D
NO2 RELAY 2 - NORMALLY OPEN
ARM RELAY 2 - COM
NC2 RELAY 2 - NORMALLY CLOSE

TABLE 2B
CONTACT INPUT WIRING CHART
2300 CONTACT DESCRIPTION
1S CONFIG LOCK
1C COM
CHASSIS
3S ALARM INHIBIT
3C COM
2S ALARM RESET
2C COM
C CHASSIS
CHASSIS
C
CHASSIS

TABLE 2C
POWER INPUT WIRING CHART
2300 CONTACT DESCRIPTION
+ DC 24V +
- DC 24V COM
CHASSIS

TABLE 2D (2300/20)
ANALOG OUTPUT WIRING CHART
B 2300 CONTACT DESCRIPTION
SHD SHIELD
B
R1+ RECORDER 1
R1- RECORDER 1 - COM
R2+ RECORDER 2
R2- RECORDER 2 - COM
SHD SHIELD

TABLE 2D (2300/25)
SPA CONNECTION WIRING CHART
2300 CONTACT DESCRIPTION
S SHIELD
R POWER
B COM
W SIGNAL -
A G SIGNAL + A
S SHIELD
R POWER
B COM
W SIGNAL -
G SIGNAL + CAGE CODE SIZE DWG NO.
201. TERMINAL DEFINITION
3WAP1 D 106M5801
NOTES: SEE SHEET 1 (UNLESS OTHERWISE SPECIFIED) PLOT SCALE NONE SHEET 2 OF 11

8 7 6 5 4 3
CDA/106M5801/000/09
2 1
 8 7 6 5 4 3 2 1
REVISION

SEE SHEET 1

D TABLE 3E D
INPUT CHANNEL WIRING CHART
2300 CONTACT DESCRIPTION
CHASSIS
COM CHANNEL 1 COM
SIG CHANNEL 1 SIGNAL
PWR CHANNEL 1 POWER
+ CHANNEL 1 A/+
- CHANNEL 1 B/-
CHASSIS
COM CHANNEL 2 COM
SIG CHANNEL 2 SIGNAL
PWR CHANNEL 2 POWER
+ CHANNEL 2 A/+
- CHANNEL 2 B/-
CHASSIS
KCM KPH COM
C KSG KPH SIGNAL
C
KPW KPH POWER

B B

0.25

NOT TO EXCEED
2 INCHES
A A

302. WIRE STRIP LENGTH

CAGE CODE SIZE DWG NO.
301. TERMINAL DEFINITION 3WAP1 D 106M5801
NOTES: SEE SHEET 1 (UNLESS OTHERWISE SPECIFIED) PLOT SCALE NONE SHEET 3 OF 11

8 7 6 5 4 3
CDA/106M5801/000/09
2 1
 8 7 6 5 4 3 2 1
REVISION

SEE SHEET 1

SAFE AREA
OR ZONE 2 ZONE 0
D OR CLASS I DIV 2 OR CLASS 1, DIV I D
OR CLASS I ZONE2 OR CLASS1, ZONE 0

VT (-24 Vdc)
COM
OUT
CUST ID:
MADE IN U.S.A.

WIRING FOR KPH/SPEED SHOWN.

C WARNING!
C
IMPROPER GROUNDING OF SIGNAL COMMON 3300XL 8mm PROXIMITOR SHOWN.
COULD CAUSE EXPLOSION OR FIRE IN THE DIAGRAM ALSO APPLIES TO PART
HAZARDOUS AREA, RESULTING IN PERSONAL NUMBERS AS SHOWN IN TABLE 4B.
INJURY OR DEATH.COMMON MUST BE
CONNECTED TO EARTH GROUND AT THE
BARRIER RAIL.

TABLE 4B
TABLE 4A
TRANSDUCERS AREA TYPE
PROXIMITOR MODULE WIRING CHART
3300XL 8MM PRODUCT
2300 CONTACT PROXIMITOR MODULE CONTACT CERTIFICATIONS TO BE
3300XL NSV
KPW VT VERIFIED FOR THE
B KSG OUT
3300XL 5MM
SPECIFIC LOCATION OF B
PROXPAC XL 330880 INSTALLATION
406 BARRIERS LOCATED IN DIVISION 2 OR ZONE 2 HAZARDOUS KCM COM
AREAS MUST BE INSTALLED IN IP54 APPROVED PROTECTIVE PROXPAC XL 330881
HOUSINGS AND INSTALLED IN ACCORDANCE WITH 3300XL 11MM
MANUFACTURER'S INSTRUCTIONS. FINAL INSTALLATION 3300XL 25MM
TO BE APPROVED BY LOCAL AUTHORITY HAVING JURISDICTION.

405 BARRIERS ARE MOUNTED TO BARRIER RAIL, WHICH IS THE

POTENTIAL EQUALIZATION BUS BETWEEN SYSTEM GROUND AND
EARTH GROUND. TO MINIMIZE GROUND LOOP PROBLEMS, A
SINGLE POINT EARTH GROUND TO SYSTEM COMMON IS
REQUIRED AT THE BARRIER RAIL. TOTAL EARTH LOOP
IMPEDANCE MUST BE LESS THAN 1 OHM. OPEN THE JUMPER
ON THE GROUND/CHASSIS CONNECTION.
(REFER TO PAGE 1, NOTE 105).
404 WIRING SHIELDS ARE TERMINATED AT THE BARRIER GROUND.
SHIELDS FLOAT AT THE 2300 TERMINAL BLOCK AND THE
PROXPAC. SHIELDS SHOULD BE INSULATED UP TO THE POINT 411 CONNECT THE GROUND/CHASSIS TERMINAL TO THE BARRIER RAIL.
OF CONNECTION. MAXIMUM CHASSIS PIGTAIL MUST NOT
EXCEED 2 INCHES (50.8 MM).
410 DELETE.
A 403. WHEN INSTALLED IN A CLASS I, ZONE2/DIV2 LOCATION,
REFER TO THE SAFE PARAMETERS IN PAGE 11. 409. STRIP WIRE ENDS 0.25 INCH (6.35 MM). MAXIMUM CHASSIS PIGTAIL A
MUST NOT EXCEED 2 INCHES (50.8 MM). SEE PAGE 3.
402. WIRING RECOMMENDATIONS:
SINGLE CABLE ASSEMBLY, STRANDED 3-WIRE 16 TO 18 AWG 408 3300XL PROXIMITOR CASE HAS BUILT-IN CASE ISOLATION, AND IS
WITH 100% SHIELD COVERAGE AND INSULATING SHEATH. ELECTRICALLY ISOLATED FROM EARTH GROUND.
401. WIRING SHOWN WITH BARRIERS. 407 FOR USE WITH THE PROXIMITOR: CAGE CODE SIZE DWG NO.
CONSULT PAGE 6 FOR WIRING WITHOUT BARRIERS. SAFETY BARRIER (MTL 7796(-) ) IS RECOMMENDED. 3WAP1 D 106M5801
NOTES: SEE SHEET 1 (UNLESS OTHERWISE SPECIFIED) PLOT SCALE NONE SHEET 4 OF 11

8 7 6 5 4 3
CDA/106M5801/000/09
2 1
 8 7 6 5 4 3 2 1
REVISION

SEE SHEET 1

TABLE 5A
MTL 7787(-) (SHOWN HERE)
BARRIER BARRIER ACCELEROMETER R
2300 MODULE R 507
SAFE AREA HAZ AREA OR VELOMITOR
D - 1 3 B
D
+ 2 4 A
EARTH RAIL EARTH RAIL SHIELD
P&F Z887
511 BARRIER BARRIER ACCELEROMETER R
2300 MODULE SAFE AREA HAZ AREA OR VELOMITOR
R

- 8 1 B
+ 5 4 A
SHIELD/GND SHIELD/GND SHIELD

SAFE AREA
OR ZONE 2 ZONE 0
OR CLASS I DIV 2 OR CLASS 1, DIV I
OR CLASS I ZONE2 OR CLASS1, ZONE 0

C C
MTL 7787(-) (SHOWN HERE)
506 507

2 4
1 3

505 504

CHANNEL 1
B ACCELEROMETER
R B
505 510
ACCELEROMETER

507 BARRIER RECOMMENDATION: MTL 787(-) (BNC P/N 02204023), P&F Z887, OR EQUIVALENT.
SEE TABLE FOR INFORMATION REGARDING WIRING TO THE BARRIERS. BN PART NUMBER 200350 SHOWN.
THIS DRAWING IS ALSO APPLICABLE
506 BARRIERS LOCATED IN DIVISION 2 OR ZONE 2 HAZARDOUS AREAS MUST BE INSTALLED TO PART NUMBERS AS SHOWN IN T
IN IP54 APPROVED PROTECTIVE HOUSINGS AND INSTALLED IN ACCORDANCE WITH ABLE 5B.
MANUFACTURER'S INSTRUCTIONS. FINAL INSTALLATION TO BE APPROVED BY
LOCAL AUTHORITY HAVING JURISDICTION.
505 BARRIERS ARE MOUNTED TO BARRIER RAIL, WHICH IS THE POTENTIAL EQUALIZATION
BUS BETWEEN SYSTEM GROUND AND EARTH GROUND. TO MINIMIZE GROUND LOOP TABLE 5B
PROBLEMS, A SINGLE POINT EARTH GROUND TO SYSTEM COMMON IS REQUIRED AT
THE BARRIER RAIL. TOTAL EARTH LOOP IMPEDANCE MUST BE LESS THAN 1 OHM. TRANSDUCERS AREA TYPE
OPEN THE JUMPER ON THE GROUND/CHASSIS CONNECTION. (REFER TO PAGE 1, 200350 PRODUCT CERTIFICATIONS TO
NOTE 105). BE VERIFIED FOR THE SPECIFIC
AP3500T2-Z1
504 TRANSDUCER SHIELDS ARE JOINED AS SHOWN TERMINATING AT BARRIER GROUND. LOCATION OF INSTALLATION
190501
SHIELDS SHOULD BE INSULATED. MAXIMUM CHASSIS PIGTAIL MUST NOT
EXCEED 2 INCHES (50.8 MM). 330500
R
511 DELETE. 330505 ACCELEROMETER
503. WHEN INTERFACING TO INTRINSICALLY SAFE APPARATUSES LOCATED
A IN A CLASS I, ZONE2/DIV2 LOCATION, REFER TO THE SAFE
PARAMETERS IN PAGE 11. 510 CONNECT THE GROUND/CHASSIS TERMINAL TO THE BARRIER RAIL.
330525 TOP VIEW A
502. WIRING RECOMMENDATIONS: 509. WIRING SHIELDS ARE TERMINATED AT THE 2300 TERMINAL
R
2300 TO BARRIERS - BARRIERS TO ACCELEROMETER : 16AWG TO 18AWG BLOCK CONTACT MARKED " ". SHIELDS SHOULD BE INSULATED
STRANDED 2-WIRE SHIELDED WITH INSULATING SHEATH. UP TO THE POINT OF CONNECTION.

501. WIRING SHOWN WITH BARRIERS. 508. STRIP WIRE ENDS 0.25 INCH (6.35 MM). MAXIMUM CHASSIS PIGTAIL CAGE CODE SIZE DWG NO.
CONSULT PAGE 7 FOR WIRING WITHOUT BARRIERS. MUST NOT EXCEED 2 INCHES (50.8 MM). SEE PAGE 3. 3WAP1 D 106M5801
NOTES: SEE SHEET 1 (UNLESS OTHERWISE SPECIFIED) PLOT SCALE NONE SHEET 5 OF 11

8 7 6 5 4 3
CDA/106M5801/000/09
2 1
 8 7 6 5 4 3 2 1
REVISION

SEE SHEET 1

SAFE AREA
D OR ZONE 2 D
OR CLASS I DIV 2
OR CLASS I ZONE2

C C
VT (-24 Vdc)
COM
OUT
CUST ID:
MADE IN U.S.A.

3300XL 8mm PROXIMITOR SHOWN.

DIAGRAM ALSO APPLIES TO PART
NUMBERS AS SHOWN IN TABLE 6B.

TABLE 6A TABLE 6B
PROXIMITOR MODULE WIRING CHART TRANSDUCERS AREA TYPE
2300 CONTACT PROXIMITOR MODULE CONTACT 3300XL 8MM PRODUCT
KPW VT 3300XL NSV CERTIFICATIONS TO BE
KSG OUT VERIFIED FOR THE
3300XL 5MM
SPECIFIC LOCATION OF
B KCM COM PROXPAC XL 330880 INSTALLATION B
PROXPAC XL 330881
3300XL 11MM
3300XL 25MM

608 DELETE.

607. STRIP WIRE ENDS 0.25 INCH (6.35 MM). MAXIMUM CHASSIS PIGTAIL
MUST NOT EXCEED 2 INCHES (50.8 MM). SEE PAGE 3.
606. TO MINIMIZE GROUND LOOP NOISE PROBLEMS, A SINGLE POINT
EARTH GROUND TO SYSTEM COMMON IS RECOMMENDED.
CONNECTION IS MADE AT THE TERMINAL BASE, SEE PAGE 1,
NOTE 105.
605 3300XL PROXIMITOR CASE HAS BUILT-IN CASE ISOLATION, AND IS
ELECTRICALLY ISOLATED FROM EARTH GROUND.
604 WIRING SHIELDS ARE TERMINATED AT THE 2300 TERMINAL BLOCK CONTACT
MARKED " " ONLY AND LEFT FLOATING AT THE PROXIMITOR/PROXPAC
END. SHIELDS SHOULD BE INSULATED UP TO THE POINT OF CONNECTION.
603. MAXIMUM CABLE LENGTH BETWEEN 2300 AND PROXPAC MUST
A NOT EXCEED 1000 FEET (305 METERS). A
602. WIRING RECOMMENDATIONS: 610. REFER TO THE ENTITY PARAMETERS ON PAGE 11.
SINGLE CABLE ASSEMBLY, STRANDED 3-WIRE 16 TO 24 AWG
WITH 100% SHIELD COVERAGE AND INSULATING SHEATH.
609. WHEN INTERFACING TO INTRINSICALLY SAFE
601. WIRING SHOWN WITHOUT BARRIERS. APPARATUSES LOCATED IN A CLASS I, ZONE2/DIV2
CONSULT PAGE 4 FOR WIRING WITH BARRIERS. LOCATION, REFER TO THE SAFE PARAMETERS IN PAGE 11. CAGE CODE SIZE DWG NO.

3WAP1 D 106M5801
NOTES: SEE SHEET 1 (UNLESS OTHERWISE SPECIFIED) PLOT SCALE NONE SHEET 6 OF 11

8 7 6 5 4 CDA/106M5801/000/09
3 2 1
 8 7 6 5 4 3 2 1
REVISION

SEE SHEET 1

SAFE AREA
OR ZONE 2
D OR CLASS I DIV 2 D
OR CLASS I ZONE2

TABLE 7A TABLE 7B
ACCELEROMETER OR VELOMITOR TRANSDUCERS AREA TYPE
AM3100T2-Z2 PRODUCT
WIRING CHART CERTIFICATIONS TO BE
TP100
R R VERIFIED FOR THE
2300 MODULE ACCELEROMETER OR VELOMITOR TP500
SPECIFIC LOCATION OF
703 200350 INSTALLATION
- B
AP3500T2-Z1
+ A
AS3100S2-Z2
SHIELD 190501
330500
C 330505 C
330525

B CHANNEL 1 B
ACCELEROMETER R

708. REFER TO THE ENTITY PARAMETERS ON PAGE 11.

BN PART NUMBER AM3100T2-Z2 SHOWN.
707. WHEN INTERFACING TO INTRINSICALLY SAFE APPARATUSES THIS DRAWING IS ALSO APPLICABLE TO PART
LOCATED IN A CLASS I, ZONE2/DIV2 LOCATION, REFER TO NUMBERS AS SHOWN IN TABLE 7B.
THE SAFE PARAMETERS IN PAGE 11.
706 DELETE.

705. STRIP WIRE ENDS 0.25 INCH (6.35 MM). MAXIMUM CHASSIS PIGTAIL
MUST NOT EXCEED 2 INCHES (50.8 MM). SEE PAGE 3.
704. TO MINIMIZE GROUND LOOP NOISE PROBLEMS, A SINGLE POINT
EARTH GROUND TO SYSTEM COMMON IS RECOMMENDED.
CONNECTION IS MADE AT THE CHASSIS, SEE PAGE 1, NOTE 105.
703 WIRING SHIELDS ARE TERMINATED AT THE 2300 TERMINAL
BLOCK CONTACT MARKED " ". SHIELDS SHOULD BE INSULATED A B
A UP TO THE POINT OF CONNECTION. MAXIMUM CHASSIS PIGTAIL
MUST NOT EXCEED 2 INCHES (50.8 MM).
A
702. WIRING RECOMMENDATIONS:
SINGLE CABLE ASSEMBLY, STRANDED 2-WIRE 16 TO 24 AWG
WITH 100% SHIELD COVERAGE AND INSULATING SHEATH. ACCELEROMETER R
TOP VIEW
701. WIRING SHOWN WITHOUT BARRIERS. CAGE CODE SIZE DWG NO.
CONSULT PAGE 5 FOR WIRING WITH BARRIERS. 3WAP1 D 106M5801
NOTES: SEE SHEET 1 (UNLESS OTHERWISE SPECIFIED) PLOT SCALE NONE SHEET 7 OF 11

8 7 6 5 4 3
CDA/106M5801/000/09
2 1
 8 7 6 5 4 3 2 1
REVISION

SEE SHEET 1
SAFE AREA
OR ZONE 2
OR CLASS I DIV 2
D OR CLASS I ZONE2 D

803

C C

804

MAGNETIC PICK-UP SENSOR

BN PART NUMBER: 284947 OR SIMILAR

B B

808. REFER TO THE ENTITY PARAMETERS ON PAGE 11.

807 DELETE.
806. STRIP WIRE ENDS 0.25 INCH (6.35 MM). MAXIMUM CHASSIS PIGTAIL
MUST NOT EXCEED 2 INCHES (50.8 MM). SEE PAGE 3.
805. TO MINIMIZE GROUND LOOP NOISE PROBLEMS, A SINGLE POINT
EARTH GROUND TO SYSTEM COMMON IS RECOMMENDED.
CONNECTION IS MADE AT THE CHASSIS, SEE PAGE 1,
NOTE 105.
TABLE 8A
804 MAGNETIC PICK-UP SENSOR CASE HAS BUILT-IN CASE
ISOLATION, AND IS ELECTRICALLY ISOLATED FROM EARTH MAGNETIC PICK-UP WIRING CHART
GROUND. 2300 CONTACT MAG PICK-UP LEAD COLOR
803 WIRING SHIELDS ARE TERMINATED AT THE 2300 TERMINAL KCM WHITE
BLOCK CONTACT MARKED " ". SHIELDS SHOULD BE INSULATED KSG BLACK
A UP TO THE POINT OF CONNECTION. MAXIMUM CHASSIS PIGTAIL
MUST NOT EXCEED 2 INCHES (50.8 MM).
A
802. WHEN INTERFACING TO INTRINSICALLY SAFE APPARATUSES
IN A CLASS I, DIV2 LOCATION, REFER TO THE SAFE
PARAMETERS IN PAGE 11.
801. WIRING SHOWN WITHOUT BARRIERS. CAGE CODE SIZE DWG NO.

3WAP1 D 106M5801
NOTES: SEE SHEET 1 (UNLESS OTHERWISE SPECIFIED) PLOT SCALE NONE SHEET 8 OF 11

8 7 6 5 4 3
CDA/106M5801/000/09
2 1
 8 7 6 5 4 3 2 1
REVISION

SEE SHEET 1

SAFE AREA
OR ZONE 2
D OR CLASS I DIV 2 D
OR CLASS I ZONE2

C PROXIMITY SWITCH C
BN PART NUMBER 100M0741 SHOWN

B B

907. REFER TO THE ENTITY PARAMETERS ON PAGE 11.

906 DELETE.
905. STRIP WIRE ENDS 0.25 INCH (6.35 MM). MAXIMUM CHASSIS PIGTAIL
MUST NOT EXCEED 2 INCHES (50.8 MM). SEE PAGE 3. TABLE 9A
904. TO MINIMIZE GROUND LOOP NOISE PROBLEMS, A SINGLE POINT PROXIMITY SWITCH WIRING CHART
EARTH GROUND TO SYSTEM COMMON IS RECOMMENDED. PROXIMITY SWITCH LEAD COLOR
CONNECTION IS MADE AT THE CHASSIS, SEE PAGE 1, NOTE 105. 2300 CONTACT
KCM BROWN
903. WIRING SHIELDS ARE TERMINATED AT THE 2300 TERMINAL KSG BLACK
BLOCK CONTACT MARKED " ". SHIELDS SHOULD BE INSULATED
A UP TO THE POINT OF CONNECTION.MAXIMUM CHASSIS PIGTAIL KPW BLUE A
MUST NOT EXCEED 2 INCHES (50.8 MM).
902. WHEN INTERFACING TO INTRINSICALLY SAFE APPARATUSES
LOCATED IN A CLASS I, DIV2 LOCATION, REFER TO THE
SAFE PARAMETERS IN PAGE 11.
901. WIRING SHOWN WITHOUT BARRIERS. CAGE CODE SIZE DWG NO.

3WAP1 D 106M5801
NOTES: SEE SHEET 1 (UNLESS OTHERWISE SPECIFIED) PLOT SCALE NONE SHEET 9 OF 11

8 7 6 5 4 3
CDA/106M5801/000/09
2 1
 8 7 6 5 4 3 2 1
REVISION

SEE SHEET 1
SAFE AREA
OR ZONE 2
OR CLASS I DIV 2
D OR CLASS I ZONE2 D

1003
TABLE 10A (2300/20) TABLE 10B (2300/25)
1003
ANALOG OUTPUT WIRING CHART SPA LINE CONNECTION WIRING CHART
2300 CONTACT DESCRIPTION 2300 CONTACT WIRE (P/N 85033) DESCRIPTION
SHD SHIELD S SHLD SHIELD
R1+ RECORDER 1 R RED POWER
R1- RECORDER 1 - COM B BLACK COM
W WHITE SIGNAL -
C R2+
R2-
RECORDER 2
RECORDER 2 - COM G GREEN SIGNAL +
C
SHD SHIELD 1004 S SHLD SHIELD
R RED POWER
B BLACK COM
W WHITE SIGNAL -
1004
G GREEN SIGNAL +

1004 1004

1002 ADDITIONAL SPA COMPATIBLE DEVICES

1001
B 1005
B

1005 WIRING RECOMMENDATIONS:

SINGLE CABLE ASSEMBLY, STRANDED 2-WIRE 16 TO 18 AWG
WITH 100% SHIELD COVERAGE AND INSULATING SHEATH.
1004 THE DRAIN WIRE CONNECTED WITH THE TERMINAL BLOCK 'S
SHIELD TERMINAL (2300/20) OR SHIELD TERMINAL(2300/25).
A A
1003 DELETE.

1002 CONNECTION DETAILS AND ENTITY PARAMETERS AS PER

DRAWING NO. 112M7732.
1001 SYSTEM CABLE IS BN CABLE 85033. CAGE CODE SIZE DWG NO.

3WAP1 D 106M5801
NOTES: SEE SHEET 1 (UNLESS OTHERWISE SPECIFIED) PLOT SCALE NONE SHEET 10 OF 11

8 7 6 5 4 3
CDA/106M5801/000/09
2 1
 8 7 6 5 4 3 2 1
REVISION

SEE SHEET 1

1. THE SYSTEM COULD BE INSTALLED IN A SAFE AREA (UNCLASSIFIED) AND THIS WOULD STILL BE APPLICABLE TO INTERFACING WITH EQUIPMENT
IN DIV. 2 / ZONE 2 AREA.
THE FIELD WIRING MUST MEET THE FOLLOWING INTRINSICALLY SAFE PARAMETERS

D A. INTRINSICALLY SAFE EQUIPMENT CERTIFIED FOR CONNECTION TO INDIVIDUAL CIRCUITS

D
WHEN INTERFACING THE 2300 VIBRATION MONITOR TO INTRINSICALLY SAFE APPARATUSES LOCATED IN THE ZONE 2 / DIV. 2 AREA, THE FOLLOWING ENTITY PARAMETERS MUST BE OBSERVED:

B. INTRINSICALLY SAFE EQUIPMENT CERTIFIED WITH ENTITY PARAMETERS

MATCH CERTIFIED INTRINSICALLY SAFE EQUIPMENT PARAMETERS WITH THE PARAMETERS ABOVE SUCH THAT THE FOLLOWING CONDITIONS ARE MET:
Uo (Voc) ≤ Ui
Io (Isc) ≤ Ii
Co (Ca) ≥
≥
C C
C. INTRINSICALLY SAFE CIRCUITS SHALL BE ISOLATED BY 500V MINIMUM FROM THE CHASSIS OF THE ELECTRICAL EQUIPMENT/ENCLOSURE.

2. WARNING
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS;
and
AVERTISSEMENT-RISQUE D'EXPLOSION-AVANT DE DÉCONNECTER L'EQUIPEMENT, COUPER LE COURANT OU S'ASSURER QUE L'EMPLACEMENT EST DÉSIGNÉ NON DAN-GEREUX.

WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2;
and
AVERTISSEMENT-RISQUE D'EXPLOSION-LA SUBSTITUTION DECOMPOSANTS PEUT RENDRE CE MATÉRIEL INACCEPTABLE POUR LES EMPLACEMENTS DE CLASSE I, DIVISION 2.

B B
WARNING -HAZARDOUS VOLTAGE MAY BE PRESENT ON RELAY CONTACT WIRING. DO NOT SERVICE UNLESS RELAY CONNECTION WIRING IS DE-ENERGIZED.
AND
AVERTISSEMENT-DES TENSIONS ÉLEVÉES PEUVENT ÊTRE PRÉSENTES SUR LE CÂBLAGE DU RELAIS À CONTACT. NE PAS FAIRE DE MAINTENANCE SAUF SI LE CÂBLAGE DE CONNEXION
DU RELAIS EST HORS TENSION.

3. SPECIAL CONDITIONS FOR SAFE USE

I ENCLOSURE REQUIREMENTS (EXCEPT FOR NORTH AMERICA):

· THE EQUIPMENT SHALL BE INSTALLED IN A SUITABLE ENCLOSURE THAT PROVIDES A DEGREE OF PROTECTION OF AT LEAST IP54 AND MEETS THE RELEVANT ENCLOSURE REQUIREMENTS OF IEC60079-0 AND IEC60079-15. THE
ENCLOSURE SHALL ALSO ENSURE A POLLUTION DEGREE 2 ENVIRONMENT FOR THE ELECTRONICS.
FOR NORTH AMERICA APPLICATIONS:
· FOR ZONE 2 INSTALLATIONS, THE EQUIPMENT SHALL BE INSTALLED IN AN ADDITIONAL ENCLOSURE THAT PROVIDES A DEGREE OF PROTECTION NOT LESS THAN IP54 ACCORDING TO 60079-15. THE INSTALLER SHALL ENSURE
THAT THE MAXIMUM AMBIENT RATED TEMPERATURE OF THE 2300 VIBRATION MONITOR IS NOT EXCEEDED. THE ENCLOSURE SHALL BE ACCEPTABLE TO THE LOCAL AUTHORITY HAVING JURISDICTION.
· FOR DIVISION 2 INSTALLATIONS, THE EQUIPMENT SHALL BE HOUSED IN AN ENCLOSURE ACCEPTABLE TO THE LOCAL AUTHORITY HAVING JURISDICTION.

A II THE RELAY CONTACTS ARE RATED 30V, 5A. A

CAGE CODE SIZE DWG NO.

3WAP1 D 106M5801
NOTES: SEE SHEET 1 (UNLESS OTHERWISE SPECIFIED) PLOT SCALE NONE SHEET 11 OF 11

8 7 6 5 4 3
CDA/106M5801/000/09
2 1