Bulletin 71.

4
D100165X012 H200 Series
December 2019

H200 Series Relief Valves

W1929_1 W0120_1

Figure 1. External View of H200 Series Relief Valve Figure 2. Sectional View of H200 Series Relief Valve

Introduction Features
The H200 Series Pop™ relief valves, Figures 1 and 2,   • Space-Saving Construction - Small relief valve
are self-operated relief valves with preset and pinned size allows installation where space is limited.
spring retainers. The inlet pressure registers directly
 • Economical - Low initial cost, easy installation
on a spring-opposed poppet assembly which includes
and high capacity per dollar invested reduces
a Nitrile (NBR) disk. When the inlet gas pressure
total cost of having relief valve capabilities in
increases above the spring setting, the poppet and disk
your system.
assembly is pushed away from the orifice. Springs
are available that provide any relief pressure setting  • Durable - Brass body construction and stainless
from 25 to 300 psig / 1.7 to 20.7 bar. steel spring reduces susceptibility to corrosion
damage and the preset, pinned spring retainer
With this simple operation and wide spring setting
prevents relief valve setpoint tampering.
selection, the H200 Series Pop relief valves may be
used where venting to atmosphere is acceptable,
where the process gas is compatible with the Installation
Nitrile (NBR) disk, where its relief capacity is This relief valve may be installed in any position but
adequate and where some pressure relieving must be oriented so that gas discharged from the
tolerance is acceptable. Common applications valve does not create a fire, toxic or explosion hazard.
include use on pneumatic control lines of air drills, The relief valve should be protected from material and
jackhammers and other similar equipment and on conditions that could clog the outlet side of the valve
farm tap installations. The H200 Series is comprised and affect the venting of gas.
of the Types H202 and H203 relief valves with the
difference being in the inlet connection size. A typical installation is shown in Figure 3. A Type P145
raincap is recommended for use with any H200 Series
relief valve. Dimensions are shown in Figure 4.
The relief valve and installation should be checked for
compliance with all applicable codes.
H200 Series
Specifications
This section lists the specifications for H200 Series external relief valves. Factory specifications are engraved on
the body of the relief valve at the factory.

Available Configurations and End Connections Construction Materials

Type H202: 3/4 NPT connection Body, Poppet and Spring Retainer: Brass
Type H203: 1 NPT connection Disk: Nitrile (NBR)
Maximum Allowable Relief (Inlet) Pressure(1) Spring: 302 Stainless steel
400 psig / 27.6 bar Temperature Capabilities(1)
Relief Pressure Ranges(1) -20 to 160°F / -29 to 71°C
See Tables 1 and 2 Approximate Weight
Flow Capacity 0.5 lbs / 0.2 kg
See Table 2 Option
Representative Wide-Open Sizing Coefficient Type P145 raincap
Cg: 405
  1. The pressure/temperature limits in this Bulletin or any applicable code limitations should not be exceeded.

Table 1. Relief Pressure Spring Ranges

RELIEF PRESSURE SETTINGS SPRING SPRING RELIEF SETTING TOLERANCE

psig bar PART NUMBER COLOR psig bar
25 to 30 1.7 to 2.1 1H485637022 Pink
±5 ±0.34
31 to 55 2.1 to 3.8 1J152137022 White
56 to 70 3.9 to 4.8 1P391137022 Blue
65 to 95 4.5 to 6.5 T1049037022 Plain ±8 ±0.55
90 to 130 6.2 to 9.0 1F791337022 Purple
131 to 160 9.0 to 11.0 1F7912T0012 Yellow
161 to 190 11.1 to 13.1 T12699T0012 Green
±15 ±1.03
191 to 235 13.2 to 16.2 1F790937022 Brown
236 to 300 16.3 to 20.7 1E954637052 Plain

Table 2. Relief Set Pressures and Capacities

RELIEF SET PRESSURE(1) SET PRESSURE PLUS BUILD-UP FLOW CAPACITY(2)

psig bar psig bar SCFH Nm3/h
25 1.7 50 3.4 34,200 916
50 3.4 75 5.2 47,400 1270
75 5.2 100 6.9 60,000 1608
100 6.9 120 8.3 69,600 1865
125 8.6 150 10.3 83,400 2235
150 10.3 180 12.4 100,500 2693
175 12.1 210 14.5 117,600 3152
200 13.8 240 16.5 132,000 3538
225 15.5 270 18.6 150,000 4020
250 17.2 300 20.7 165,000 4422
275 19.0 330 22.7 180,000 4824
300 20.7 360 24.8 195,000 5226
1. This is the initial leak point, the point at which the relief valve begins to discharge.
2. 0.6 Specific Gravity Gas. To convert to equivalent capacities of other gases, multiply the table values by 0.775 for air or 0.789 for nitrogen. Multiply the flow obtained by 0.0268 to
convert to (Nm3/h) at 0°C and 1.01 bar.

Ordering Information
When ordering an H200 Series relief valve, specify the
type number and the relief pressure setting required.

2
 H200 Series

TYPE P145 RAIN CAP

H200 SERIES
RELIEF VALVE LOW-PRESSURE
REDUCING REGULATOR

HIGH-
PRESSURE
REDUCING
REGULATOR

INLET PRESSURE

AF9930-C
A1619-1

Figure 3. Typical Farm Tap Installation

1.75 /
44.5

0.12 /
3.1
GROOVE PIN

3.06 /
77.7

AE8234
APPROXIMATE
TOP OF BOSS

IN. /
mm

Figure 4. Dimensions

3
H200 Series

[email protected] Facebook.com/EmersonAutomationSolutions
Fisher.com LinkedIn.com/company/emerson-automation-solutions
Twitter.com/emr_automation
D100165X012 © 1979, 2019 Emerson Process Management Regulator
Technologies, Inc. All rights reserved. 12/19.
Emerson Automation Solutions The Emerson logo is a trademark and service mark of Emerson
Electric Co. All other marks are the property of their prospective owners.
Fisher™ is a mark owned by Fisher Controls International LLC, a
Americas Asia Pacific business of Emerson Automation Solutions.
McKinney, Texas 75070 USA Singapore 128461, Singapore The contents of this publication are presented for informational purposes
T +1 800 558 5853 T  +65 6777 8211 only, and while every effort has been made to ensure their accuracy, they are
+1 972 548 3574 not to be construed as warranties or guarantees, express or implied,
regarding the products or services described herein or their use or
Europe Middle East and Africa applicability. All sales are governed by our terms and conditions, which
Bologna 40013, Italy Dubai, United Arab Emirates are available upon request. We reserve the right to modify or improve the
T  +39 051 419 0611 T  +971 4 811 8100 designs or specifications of such products at any time without notice.
Emerson Process Management Regulator Technologies, Inc does not
assume responsibility for the selection, use or maintenance of any
product. Responsibility for proper selection, use and maintenance of any
Emerson Process Management Regulator Technologies, Inc. product
remains solely with the purchaser.