Back to Main Menu

RTTS™ PACKER AND SSC™ II VALVE

HN00501

HN00500

RTTS PACKER SSC II VALVE

• Hookwall type retrievable packer • Full-opening, ball-type, subsurface
designed for testing, treating, and control valve.
squeezing.
and Strengths

• Can be installed without left-hand

Dimensions

• Optional integral circulating valve rotation eliminating the problems

may be opened and locked at any inherent when unscrewing pipe
time to allow circulation above the joints.
packer. • Ball valve automatically closes to
• Designed to hold pressure from shut in the well when the SSC II is
either direction. set down.
• Ideal for performing multiple • Ball valve is opened by picking up
operations on one or more zones and can be reclosed by setting
with only one trip in the well. back down if high pressure is
detected below the valve.
• Large mandrel ID allows pumping
large volumes of fluid with • Only right-hand rotation is
minimum pressure drop. required to release the workstring
• Large ID also allows passage of from the valve.
tubing-type perforating guns. • Rotation is not required to reattach
• Sizes available to run in all the workstring to the valve.
standard casing sizes from • Can be used to test the blowout
23/8-in. through 20-in. O.D. preventers during drilling.
 CHAMP® PACKERS

HN00502
and Strengths
Dimensions

CHAMP PACKER
• Hookwall-type retrievable packer
with a concentric bypass.
HN00503

• Design helps eliminate problems

associated with accidently
opening a conventional bypass
CHAMP L/L PACKER during circulation around the
bottom of the packer.
• Liner-lock feature allows the
Champ packer to be locked in • Excellent for use in highly
the running position until it lands deviated wells or where pipe
on the appropriate liner. manipulation is difficult.

• Excellent for use in highly • Bypass can be opened by picking

deviated wells with deep liners. straight up (no torque required).
• Easy to relocate in multiple zones
with only one trip in the well for
treating, testing, or squeezing.
 Page 1

SECTION NO. 200

DIMENSIONS
and
STRENGTHS

Copyright. © 1995 HaIliburton Company

ALL RIGHTS RESERVED

Page 2

TABLE
DIMENSIONS AND STRENGTHS OF NON-UPSET
Wt. per Ft. With
Size Coupings, Lb. Inside Drift
O.D. Grade Diameter Diameter
In. Non- Upset Integral In. In.
Upset Joint

1.050 *F-25 — 1.20 — .824 .730

H-40 1.14 1.20 — .824 .730
J-55 1.14 1.20 1.20 .824 .730
C-75 1.14 1.20 1.20 .824 .730
N-80 1.14 1.20 1.20 .824 .730
1.315 *F-25 — 1.80 — 1.049 .955
H-40 1.70 1.80 1.72 1.049 .955
J-55 1.70 1.80 1.72 1.049 .955
*J-55 — — 2.25 .957 .848
C-75 1.70 1.80 1.72 1.049 .955
*C-75 — — 2.25 .957 .848
N-80 1.70 1.80 1.72 1.049 .955
*N-80 — — 2.25 .957 .848
*P105 — — 2.25 .957 .848
1.660 *F-25 — 2.40 — 1.380 1.286
H-40 — — 2.10 1.410 1.286
H-40 2.30 2.40 2.33 1.380 1.286
J-55 — — 2.10 1.410 1.286
J-55 2.30 2.40 2.33 1.380 1.286
*J-55 — — 3.02 1.278 1.184
C-75 2.30 2.40 2.33 1.380 1.286
*C-75 — — 3.02 1.278 1.184
N-80 2.30 2.40 2.33 1.380 1.286
*N-80 — — 3.02 1.278 1.184
*P-105 — — 3.02 1.278 1.184
1.900 *F-25 2.75 2.90 — 1.610 1.516
H-40 — — 2.40 1.650 1.516
H-40 2.75 2.90 2.76 1.610 1.516
J-55 — — 2.40 1.650 1.516
J-55 2.75 2.90 2.76 1.610 1.516
*J-55 — — 3.64 1.500 1.406
C-75 2.75 2.90 2.76 1.610 1.516
*C-75 — — 3.64 1.500 1.406
N-80 2.75 2.90 2.76 1.610 1.516
*N-80 — — 3.64 1.500 1.406
*P-105 — — 3.64 1.500 1.406
2.063 H-40 — — 3.25 1.751 1.657
J-55 — — 3.25 1.751 1.657
C-75 — — 3.25 1.751 1.657
N-80 — — 3.25 1.751 1.657

*Non API Standard. Shown for information only.

 Page 3

NO. 201
EXTERNAL UPSET & INTEGRAL JOINT TUBING
Threaded & Coupled ** Joint Yield Strength, Lb.***
Integral **
O.D. O.D. Joint Internal
Collapse Threaded & Coupled
of Cplg., In. of Box Yield
Resist. Integral
Non- Upset O.D. Pressure Non-
psi Upset Joint
Upset Upset In. In. psi Upset

— 1.660 1.315 — 5,960 4,710 8,320 — —

1.313 1.660 1.315 — 7,680 7,530 6,360 13,310 —
1.313 1.660 1.315 1.327 10,560 10,360 8,740 18,290 18,000
1.313 1.660 1.315 1.327 14,410 14,120 11,920 24,950 25,000
1.313 1.660 1.315 1.327 15,370 15,070 12,710 26,610 27,000
— 1.900 1.469 — 5,540 4,430 — 12,350 —
1.660 1.900 1.469 1.550 7,270 7,080 10,960 19,760 15,970
1.660 1.900 1.469 1.550 10,000 9,730 15,060 27,160 21,960
— — — 1.600 12,940 13,100 — — 35,000
1.660 1.900 1.469 1.550 13,640 13,270 20,540 37,040 29,940
— — — 1.600 17,640 17,870 — — 48,000
1.660 1.900 1.469 1.550 14,550 14,160 21,910 39,510 31,940
— — — 1.600 18,820 19,060 — — 51,000
— — — 1.600 24,700 25,010 — — 67,000
— 2.200 1.812 — 4,440 3,690 — 16,710 —
— — — 1.880 5,570 5,270 — — 22,180
2.054 2.200 1.812 1.880 6,180 5,900 15,530 26,740 22,180
— — — 1.880 7,660 7,250 — — 30,500
2.054 2.200 1.812 1.880 8,490 8,120 21,360 36,770 30,500
— — — 1.927 11,200 11,070 — — 48,000
2.054 2.200 1.812 1.880 11,580 11,070 29,120 50,140 41,600
— — — 1.927 15,270 15,100 — — 66,000
2.054 2.200 1.812 1.880 12,360 11,810 31,060 53,480 44,370
— — — 1.927 16,290 16,110 — — 71,000
— — — 1.927 21,380 21,140 — — 93,000
2.200 2.500 2.094 — 3,920 3,340 11,930 19,990 —
— — — 2.110 4,920 4,610 — — 26,890
2.200 2.500 2.094 2.110 5,640 5,340 19,090 31,980 26,890
— — — 2.110 6,640 6,330 — — 36,970
2.200 2.500 2.094 2.110 7,750 7,350 26,250 43,970 36,970
— — — 2.162 10,360 10,130 — — 57,000
2.200 2.500 2.094 2.110 10,570 10,020 35,800 59,960 50,420
— — — 2.162 14,130 13,820 — — 80,000
2.200 2.500 2.094 2.110 11,280 10,680 38,180 63,960 53,780
— — — 2.162 15,070 14,740 — — 84,000
— — — 2.162 19,780 19,340 — — 110,000
— — — 2.325 5,590 5,290 — — 35,690
— — — 2.325 7,690 7,280 — — 49,070
— — — 2.325 10,480 9,920 — — 66,910
— — — 2.325 11,180 10,590 — — 71,370

** Collapse, Internal Yield Strengths are minimum values with no safety factor,
reproduced by permission from API Bul. 5C2, Bulletin on Performance
Properties of Casing and Tubing.
Page 4

TABLE
DIMENSIONS AND STRENGTHS OF NON-UPSET
Wt. per Ft. With
Size Coupings, Lb. Inside Drift
O.D. Grade Diameter Diameter
In. Non- Upset Integral In. In.
Upset Joint

2.375 *F-25 4.00 — — 2.041 1.947

*F-25 4.60 4.70 — 1.995 1.901
H-40 4.00 — — 2.041 1.947
H-40 4.60 4.70 — 1.995 1.901
J-55 4.00 — — 2.041 1.947
J-55 4.60 4.70 4.70 1.995 1.901
*J-55 — — 5.30 1.939 1.845
*J-55 — — 6.20 1.853 1.759
*J-55 — — 7.70 1.703 1.609
C-75 4.00 — — 2.041 1.947
C-75 4.60 4.70 4.70 1.995 1.901
*C-75 — — 5.30 1.939 1.845
C-75 5.80 5.95 5.95 1.867 1.773
*C-75 — 6.20 1.853 1.759
*C-75 — — 7.70 1.703 1.609
N-80 4.00 — — 2.041 1.947
N-80 4.60 4.70 4.70 1.995 1.901
*N-80 — — 5.30 1.939 1.845
N-80 5.80 5.95 5.95 1.867 1.773
*N-80 — — 6.20 1.853 1.759
*N-80 — — 7.70 1.703 1.609
P-105 4.60 4.70 4.70 1.995 1.901
*P-105 — — 5.30 1.939 1.845
P-105 5.80 5.95 5.95 1.867 1.773
*P-105 — — 6.20 1.853 1.759
*P-105 — — 7.70 1.703 1.609
*P-110 4.60 4.70 — 1.995 1.901
*P-110 5.80 5.95 — 1.867 1.773
2.875 *F-25 6.40 6.50 — 2.441 2.347
H-40 6.40 6.50 — 2.441 2.347
J-55 6.40 6.50 6.50 2.441 2.347
*J-55 — — 7.90 2.323 2.229
*J-55 — — 8.70 2.259 2.165
*J-55 — — 9.50 2.195 2.101
*J-55 — — 10.70 2.091 1.997
*J-55 — — 11.00 2.065 1.971
C-75 6.40 6.50 6.50 2.441 2.347
*C-75 — — 7.90 2.323 2.229
C-75 8.60 8.70 8.70 2.259 2.165
*C-75 — — 9.50 2.195 2.101
*C-75 — — 10.70 2.091 1.997
*C-75 — — 11.00 2.065 1.971
N-80 6.40 6.50 6.50 2.441 2.347
*N-80 — — 7.90 2.323 2.229
N-80 8.60 8.70 8.70 2.259 2.165
*N-80 — — 9.50 2.195 2.101
*N-80 — — 10.70 2.091 1.997
*N-80 — — 11.00 2.065 1.971
P-105 6.40 6.50 6.50 2.441 2.347
*P-105 — — 7.90 2.323 2.229
P-105 8.60 8.70 8.70 2.259 2.165
*P-105 — — 9.50 2.195 2.101
*P-105 — — 10.70 2.091 1.997
*P-110 6.40 6.50 — 2.441 2.347

*Non API Standard. Shown for information only.

 Page 5

NO. 201
EXTERNAL UPSET & INTEGRAL JOINT TUBING
Threaded & Coupled ** Joint Yield Strength, Lb.***
Integral **
O.D. O.D. Joint Internal
Collapse Threaded & Coupled
of Cplg., In. of Box Yield
Resist. Integral
Non- Upset O.D. Pressure Non-
psi Upset Joint
Upset Upset In. In. psi Upset

2.875 — — — 3,530 3,080 18,830 — —

2.875 3.063 2.594 — 4,160 3,500 22,480 32,600 —
2.875 — — — 5,230 4,920 30,130 — —
2.875 3.063 2.594 — 5,890 5,600 35,960 52,170 —
2.875 — — — 7,190 6,770 41,430 — —
2.875 3.063 2.594 2.700 8,100 7,700 49,450 71,730 72,000
— — — 2.740 9,170 8,840 — — 81,000
— — — 2.937 10,760 10,580 — — 95,000
— — — 3.125 13,360 13,620 — — 118,000
2.875 — — — 9,520 9,230 56,500 — —
2.875 3.063 2.594 2.700 11,040 10,500 67,430 97,820 98,000
— — — 2.740 12,510 12,050 — — 111,000
2.875 3.063 2.594 2.906 14,330 14,040 96,560 126,940 127,000
— — — 2.937 14,670 14,420 — — 130,000
— — — 3.125 18,220 18,570 — — 161,000
2.875 — — — 9,980 9,840 60,260 — —
2.875 3.063 2.594 2.700 11,780 11,200 71,930 104,340 104,000
— — — 2.740 13,340 12,860 — — 118,000
2.875 3.063 2.594 2.906 15,280 14,970 102,990 135,400 135,000
— — — 2.937 15,650 15,390 — — 139,000
— — — 3.125 19,430 19,810 172,000
2.875 3.063 2.594 2.700 15,460 14,700 94,410 136,940 137,000
— — — 2.740 17,510 16,870 155,000
12.875 3.063 2.594 2.906 20,060 19,650 135,180 177,710 178,000
— — — 2.937 20,540 20,200 — — 182,000
— — — 3.125 25,510 26,010 — — 226,000
2.875 3.063 2.594 — 13,800 15,400 98,900 143,470 —
2.875 3.063 2.594 — 17,910 20,590 141,610 186,170 —
3.500 3.668 3.094 — 3,870 3,300 32,990 45,300 —
3.500 3.668 3.094 — 5,580 5,280 52,780 72,480 —
3.500 3.668 3.094 3.220 7,680 7,260 72,580 99,660 100,000
— — — 3.437 9,550 9,250 — — 124,000
— — — 3.500 10,530 10,320 — — 137,000
— — — 3.625 11,470 11,390 — — 149,000
— — — 3.687 12,960 13,120 — — 168,000
— — — 3.750 13,310 13,570 — — 173,000
3.500 3.668 3.094 3.220 10,470 9,910 98,970 135,900 136,000
— — — 3.437 13,020 12,600 — — 169,000
3.500 3.668 3.094 3.500 14,350 14,060 149,360 186,290 186,000
— — — 3.625 15,640 15,520 — — 203,000
— — — 3.687 17,670 17,890 — — 229,000
— — — 3.750 18,150 18,490 — — 236,000
3.500 3.668 3.094 3.220 11,160 10,570 105,570 144,960 145,000
— — — 3.437 13,890 13,450 — — 180,000
3.500 3.668 3.094 3.500 15,300 15,000 159,310 198,710 198,000
— — — 3.625 16,690 16,560 — — 217,000
— — — 3.687 18,850 19,090 — — 245,000
— — — 3.750 19,360 19,730 — — 251,000
3.500 3.668 3.094 3.220 14,010 13,870 138,560 190,260 190,000
— — — 3.437 18,230 17,650 — — 236,000
3.500 3.668 3.094 3.500 20,090 19,690 209,100 260,810 261,000
— — — 3.625 21,900 21,730 — — 285,000
— — — 3.687 24,740 25,050 — — 321,000
3.500 3.668 3.094 — 13,080 14,530 145,160 199,320 —
** Collapse, Internal Yield Strengths are minimum values with no safety factor,
reproduced by permission from API Bul. 5C2, Bulletin on Performance
Properties of Casing and Tubing.
Page 6

TABLE
DIMENSIONS AND STRENGTHS OF NON-UPSET
Wt. per Ft. With
Size Coupings, Lb. Inside Drift
O.D. Grade Diameter Diameter
In. Non- Upset Integral In. In.
Upset Joint

3.500 *F-25 7.70 — — 3.068 2.943

*F-25 9.20 9.30 — 2.992 2.867
*F-25 10.20 — — 2.922 2.797
H-40 7.70 — — 3.068 2.943
H-40 9.20 9.30 — 2.992 2.867
H-40 10.20 — — 2.922 2.797
J-55 7.70 — — 3.068 2.943
J-55 9.20 9.30 9.30 2.992 2.867
J-55 10.20 — 10.30 2.922 2.797
*J-55 — — 12.80 2.764 2.639
*J-55 — — 12.95 2.750 2.625
*J-55 — — 15.80 2.548 2.423
*J-55 — — 16.70 2.480 2.355
C-75 7.70 — — 3.068 2.943
C-75 9.20 9.30 9.30 2.992 2.867
C-75 10.20 — 10.30 2.922 2.797
*C-75 — — 12.80 2.764 2.639
C-75 12.70 12.95 12.95 2.750 2.625
*C-75 — — 15.80 2.548 2.423
*C-75 — — 16.70 2.480 2.355
N-80 7.70 — — 3.068 2.943
N-80 9.20 9.30 9.30 2.992 2.867
N-80 10.20 — 10.30 2.922 2.797
*N-80 — — 12.80 2.764 2.639
N-80 12.70 12.95 12.95 2.750 2.625
*N-80 — — 15.80 2.548 2.423
*N-80 — — 16.70 2.480 2.355
P-105 9.20 9.30 9.30 2.992 2.867
*P-105 — — 10.30 2.922 2.797
*P-105 — — 12.80 2.764 2.639
P-105 12.70 12.95 12.95 2.750 2.625
*P-105 — — 15.80 2.548 2.423
*P-105 — — 16.70 2.480 2.355
*P-110 9.20 9.30 — 2.992 2.867
*P-110 12.70 12.95 — 2.750 2.625
4.000 *F-25 9.50 — — 3.548 3.423
*F25 — 11.00 — 3.476 3.351
H-40 9.50 — — 3.548 3.423
H-40 — 11.00 — 3.476 3.351
J-55 9.50 — — 3.548 3.423
J-55 — 11.00 11.00 3.476 3.351
*J-55 — — 11.60 3.428 3.303
C-75 9.50 — — 3.548 3.423
*C-75 — 11.00 11.00 3.476 3.351
C-75 — — 13.40 3.340 3.215
N-80 9.50 — — 3.548 3.423
N-80 — 11.00 11.00 3.476 3.351
*N-80 — — 13.40 3.340 3.215
*P-105 — — 11.00 3.476 3.351
*P-105 — — 13.40 3.340 3.215

*Non API Standard. Shown for information only.

 Page 7

NO. 201
EXTERNAL UPSET & INTEGRAL JOINT TUBING
Threaded & Coupled ** Joint Yield Strength, Lb.***
Integral **
O.D. O.D. Joint Internal
Collapse Threaded & Coupled
of Cplg., In. of Box Yield
Resist. Integral
Non- Upset O.D. Pressure Non-
psi Upset Joint
Upset Upset In. In. psi Upset

4.250 — — — 2,970 2,700 40,670 — —

4.250 4.500 3.750 — 3,680 3,180 49,710 64,760 —
4.250 — — — 4,330 3,610 57,840 — —
4.250 — — — 4,630 4,320 65,070 — —
4.250 4.500 3.750 — 5,380 5,080 79,540 103,610 —
4.250 — — — 6,060 5,780 92,550 — —
4.250 — — — 5,970 5,940 89,470 — —
4.250 4.500 3.750 3.905 7,400 6,980 109,370 142,460 142,000
4.250 — — 3.955 8,330 7,950 127,250 — 160,000
— — — 4.312 10,350 10,120 — — 199,000
— — — 4.312 10,530 10,230 — — 203,000
— — — 4.500 12,950 13,090 — — 249,000
— — — 4.562 13,690 14,020 — — 264,000
4.250 — — — 7,540 8,100 122,010 — —
4.250 4.500 3.750 3.905 10,040 9,520 149,140 194,260 194,000
4.250 — — 3.955 11,360 10,840 173,530 — 219,000
— — — 4.312 14,110 13,800 — — 272,000
4.250 4.500 3.750 4.312 14,350 14,060 230,990 276,120 276,000
— — — 4.500 17,630 17,850 — — 339,000
— — — 4.562 18,670 19,130 — — 359,000
4.250 — 7,870 8,640 130,140 — —
4.250 4.500 3.750 3.905 10,530 10,160 159,090 207,220 207,000
4.250 — — 3.955 12,120 11,560 185,100 — 233,000
— — — 4.312 15,060 14,730 — — 290,000
4.250 4.500 3.750 4.312 15,310 15,000 246,390 294,530 295,000
— — — 4.500 18,800 19,040 — — 362,000
— — — 4.562 19,920 20,400 — — 383,000
4.250 4.500 3.750 3.905 13,050 13,330 208,800 271,970 272,000
— — — 3.955 15,920 15,180 — — 306,000
— — — 4.312 19,760 19,320 — — 380,000
4.250 4.500 3.750 4.312 20,090 19,690 323,390 386560 387,000
— — — 4.500 24,680 24,990 — — 475,000
— — — 4.562 26,140 26,770 — — 503,000
4.250 4.500 3.750 — 12,620 13,970 218,740 284,920 —
4250 4.500 3.750 — 17,940 20,630 338,790 365,570 —
4.750 — — — 2,630 2,470 45,000 — —
— 5.000 4.250 — 3,220 2,870 — 76,920 —
4.750 — — — 4,060 3,960 72,000 — —
— 5.000 4.250 — 4,900 4,590 — 123,070 —
4.750 — — — 5,110 5,440 99,010 — —
— 5.000 4.250 4.405 6,590 6,300 — 169,220 169,000
— — — 4.000 7,300 6,880 — — 137,000
4.750 — — — 6,350 7,420 135,010 — —
— 5.000 4.250 4.405 8,410 8,600 — 230,760 231,000
— — — 4.625 11,350 10,830 — — 285,000
4.750 — — — 6,590 7,910 144,010 — —
— 5.000 4.250 4.405 8,800 9,170 — 246,140 246,000
— — — 4.625 12,110 11,550 — — 304,000
— — — 4.405 10,700 12,040 — — 323,000
— — — 4.625 15,900 15,160 — — 400,000

** Collapse, Internal Yield Strengths are minimum values with no safety factor,
reproduced by permission from API Bul. 5C2, Bulletin on Performance
Properties of Casing and Tubing.
Page 8

TABLE
DIMENSIONS AND STRENGTHS OF NON-UPSET
Wt. per Ft. With
Size Coupings, Lb. Inside Drift
O.D. Grade Diameter Diameter
In. Non- Upset Integral In. In.
Upset Joint

4.500 *F-25 12.60 12.75 — 3.958 3.833

H-40 12.60 12.75 — 3.958 3.833
J-55 12.60 12.75 12.75 3.958 3.833
*J-55 — — 13.50 3.920 3.795
C-75 12.60 12.75 12.75 3.958 3.833
*C-75 — — 13.50 3.920 3.795
*C-75 — — 15.50 3.826 3.701
*C-75 — — 19.20 3.640 3.515
N-80 12.60 12.75 12.75 3.958 3.833
*N-80 — — 13.50 3.920 3.795
*N-80 — — 15.50 3.826 3.701
*N-80 — — 19.20 3.640 3.515
*P-105 — — 12.75 3.958 3.833
*P-105 — — 13.50 3.920 3.795
*P-105 — — 15.50 3.826 3.701
*P-105 — — 19.20 3.640 3.515

*Non API Standard. Shown for information only.

 Page 9

NO. 201
EXTERNAL UPSET & INTEGRAL JOINT TUBING
Threaded & Coupled ** Joint Yield Strength, Lb.***
Integral **
O.D. O.D. Joint Internal
Collapse Threaded & Coupled
of Cplg., In. of Box Yield
Resist. Integral
Non- Upset O.D. Pressure Non-
psi Upset Joint
Upset Upset In. In. psi Upset

5.200 5.563 4.750 — 2,870 2,630 65,230 90,010 —

5.200 5.563 4.750 — 4,500 4,220 104,360 144,020 —
5.200 5.563 4.750 4.910 5,720 5,800 143,500 198,030 198,000
— — — 4.935 6,420 6,200 — — 211,000
5.200 5.563 4.750 4.910 7,200 7,900 195,680 270,030 270,000
— — — 4.935 8,170 8,460 — — 288,000
— — — 5.125 10,390 9,830 — — 331,000
— — — 5.312 12,960 12,540 — — 412,000
5.200 5.563 4.750 4.910 7,500 8,430 208,730 288,040 288,000
— — — 4.935 8,540 9,020 — — 307,000
— — — 5.125 11,090 10,480 — — 353,000
— — — 5.312 13,820 13,380 — — 439,000
— — — 4.910 8,950 11,070 — — 378,000
— — — 4.935 10,350 11,840 — — 403,000
— — — 5.125 13,820 13,760 — — 463,000
— — — 5.312 18,140 17,560 — — 567,000

** Collapse, Internal Yield Strengths are minimum values with no safety factor,
reproduced by permission from API Bul. 5C2, Bulletin on Performance
Properties of Casing and Tubing.
Page 10

TABLE
DIMENSIONS AND STRENGTHS OF API
I.D. Collapse Pressure**
Wt. Per At.
Size Ft. I.D. Full D E G S-135
O.D. W/Cplg. In. Upset PSI PSI PSI PSI
In. Lb. In. * *

23/8 4.85 1.995 1.437 *6,850 11,040 13,250 16,560

23/8 6.65 1.815 1.125 11,440 15,600 18,720 23,400
27/8 6.85 2.441 1.875 — 10,470 12,560 15,700
27/8 10.40 2.151 1.187 12,110 16,510 19,810 24,760
31/2 9.50 2.992 2.250 — 10,040 12,110 15,140
31/2 13.30 2.764 1.875 10,350 14,110 16,940 21,170
31/2 15.50 2.602 1.750 12,300 16,770 20,130 25,160
4 11.85 3.476 2.937 — 8,410 10,310 12,820
4 14.00 3.340 2.375 8,330 11,350 14,630 17,030
41/2 13.75 3.958 3.156 — 7,200 8,920 10,910
41/2 16.60 3.826 2.812 7,620 10,390 12,470 15,590
41/2 20.00 3.640 2.812 9,510 12,960 15,560 19,450
5 16.25 4.408 3.750 — 6,970 8,640 10,550
5 19.50 4.276 3.687 7,390 10,000 12,090 15,110
51/2 21.90 4.778 3.812 6,610 8,440 10,350 12,870
51/2 24.70 4.670 3.500 7,670 10,460 12,560 15,700
59/16 *19.00 4.975 4.125 4,580 5,640 — —
59/16 *22.20 4.859 3.812 5,480 6,740 — —
59/16 *25.25 4.733 3.500 6,730 8,290 — —
65/8 *22.20 6.065 5.187 3,260 4,020 — —
65/8 25.20 5.965 5.000 4,010 4,810 6,160 6,430
65/8 *31.90 5.761 4.625 5,020 6,170 — —

**Non API Standard. Shown for information only.

**Collapse, Internal Yield and Tensile Strength are minimum values with no safety
factor.
 Page 11

NO. 202
SEAMLESS INTERNAL UPSET DRILL PIPE
Internal Yield Pressure** Tensile Strength**
G S-135 Size
D E G S-135 D E 1000 1000 O.D.
PSI PSI PSI PSI 1000 1000 Lb. Lb. In.
* * Lb. Lb. * *

*7,110 10,500 14,700 18,900 70 98 137 176 23/8

11,350 15,470 21,660 27,850 101 138 194 249 23/8
— 9,910 13,870 17,830 — 136 190 245 27/8
12,120 16,530 23,140 29,750 157 214 300 386 27/8
— 9,520 13,340 17,140 — 194 272 350 31/2
10,120 13,800 19,320 24,840 199 272 380 489 31/2
12,350 16840 23,570 30,310 237 323 452 581 31/2
— 8,600 12,040 15,470 — 231 323 415 4
7,940 10,830 15,160 19,500 209 285 400 514 4
— 7,900 11,070 14,230 — 270 378 486 41/2
7,210 9,830 13,760 17,690 242 331 463 595 41/2
9,200 12,540 17,560 22,580 302 412 577 742 41/2
— 7,770 10,880 13,980 — 328 459 591 5
6,970 9,500 13,300 17,100 290 396 554 712 5
6,320 8,610 12,060 15,500 321 437 612 787 51/2
7,260 9,900 13,860 17,820 365 497 696 895 51/2
5,090 6,950 — — 267 365 — — 59/16
6,090 8,300 — — 317 432 — — 59/16
7,180 9,790 — — 369 503 — — 59/16
4,160 5,530 — — 307 418 — — 65/8
4,790 6,540 9,150 11,770 359 489 685 881 65/8
6,275 8,540 — — 463 631 — — 65/8
Page 12

TABLE
DIMENSIONS AND
Thread & Cplg. Extreme Line
Wt. **
Size Per Ft. Inside Col’pse
O.D. Grade With Dia. Drift O.D. of Drift O.D. of Resis-
In. Cplg., In. Dia. Cplg. Dia. Box tance
Lb. In. In. In. In. PSI

41/2 *F-25 9.50 4.090 3.965 5.000 — — 1,920

H-40 9.50 4.090 3.965 5.000 — — 2,770
J-55 9.50 4.090 3.965 5.000 — — 3,310
J-55 10.50 4.052 3.927 5.000 — — 4,010
J-55 11.60 4.000 3.875 5.000 — — 4,960
K-55 9.50 4.090 3.965 5.000 — — 3,310
K-55 10.50 4.052 3.927 5.000 — — 4,010
K-55 11.60 4.000 3.875 5.000 — — 4,960
C-75 11.60 4.000 3.875 5.000 — — 6,130
C-75 13.50 3.920 3.795 5.000 — — 8,170
N-80 11.60 4.000 3.875 5.000 — — 6,350
N-80 13.50 3.920 3.795 5.000 — — 8,540
C-95 11.60 4.000 3.875 5.000 — — 7,010
C-95 13.50 3.920 3.795 5.000 — — 9,650
P110 11.60 4.000 3.875 5.000 — — 7,560
P-110 13.50 3.920 3.795 5.000 — — 10,670
P-110 15.10 3.826 3.701 5.000 — — 14,320
*V-150 15.10 3.826 3.701 5.000 — — 18,110
5 *F25 11.50 4.560 4.435 5.563 — — 1,820
J-55 11.50 4.560 4.435 5.563 — — 3,060
J-55 13.00 4.494 4.369 5.563 — — 4,140
J-55 15.00 4.408 4.283 5.563 4.151 5.360 5.550
K-55 11.50 4.560 4.435 5.563 — — 3,060
K-55 13.00 4.494 4.369 5.563 — — 4,140
K-55 15.00 4.408 4.283 5.563 4.151 5.360 5,550
C-75 15.00 4.408 4.283 5.563 4.151 5.360 6,970
C-75 18.00 4.276 4.151 5.563 4.151 5.360 10,000
*C-75 20.30 4.184 — — 4.059 5.094 11,240
*C-75 23.20 4.044 — — 3.919 5.094‡ 12,970
N-80 15.00 4.408 4.283 5.563 4.151 5.360 7,250
N-80 18.00 4.276 4.151 5.563 4.151 5.360 10,490
*N-80 20.30 4.184 — — 4.059 5.250 11,990
*N-80 23.20 4.044 — — 3.919 5.094‡ 13,830
C-95 15.00 4.408 4.283 5.563 4.151 5.360 8,090
C-95 18.00 4.276 4.151 5.563 4.151 5.360 12,010
*C-95 20.30 4.184 — — 4.059 5.250 14,250
*C-95 23.20 4.044 — — 3.919 5.094‡ 16,430
P-110 15.00 4.408 4.283 5.563 4.151 5.360 8,830
P-110 18.00 4.276 4.151 5.563 4.151 5.360 13,450
P-110 20.30 4.184 — — 4.059 5.094‡ 16,490
*P-110 23.20 4.044 — — 3.919 5.094‡ 19,020
*V-150 15.00 4.408 4.283 5.563 — — 10,260
*V-150 18.00 4.276 4.151 5.563 — — 16,860
*V-150 20.80 4.156 4.031 5.563 — — 22,860
*V-150 24.20 4.000 3.875 5.563 — — 27,000

*Non API Standard. Shown for information only.

** Collapse, Internal Yield and Joint Yield Strengths are minimum values with no
safety actor, reproduced by permission from API Bul. 5C2, Bulletin on
Performance Properties of Casing and Tubing.
 Page 13

NO. 203
STRENGTHS OF CASING
Internal Yield Pressure PSI** ** Joint Strength - 1000 Lbs.**
Body
Plain Round Thread Yield Threaded & Cplg. Joint
But- Ext.
End or Stgth. But-
tress Round Thread Line
Ext. 1,000 tress
Short Long Thd. Joint
Line Lbs. Short Long Thd.

— 1,990 — — 69 71 — — —
3,190 3,190 — — 111 77 — — —
4,380 4,380 — — 152 101 — — —
4,790 4,790 — 4,790 165 132 — 203 —
5,350 5,350 5,350 5,350 184 154 162 225 —
4,380 4,380 — — 152 112 — — —
4,790 4,790 — 4,790 165 146 — 249 —
5,350 5,350 5,350 5,350 184 170 180 277 —
7,290 — 7,290 7,290 250 — 212 288 —
8,460 — 8,460 8,460 288 — 257 331 —
7,780 — 7,780 7,780 267 — 223 304 —
9,020 — 9,0201 9,020 307 — 270 349 —
9,240 — 9,240 9,240 317 — 234 325 —
10,710 — 10,710 10,710 364 — 284 374 —
10,690 — 10,690 10,690 367 — 279 385 —
12,410 — 12,410 12,410 422 — 338 443 —
14,420 — 14,420 13,460 485 — 406 509 —
— — 19,660 18,360 661 — 519 683 —
— 1,930 — — 83 84 — — —
4,240 4,240 — — 182 133 — — —
4,870 4,870 4,870 4,870 208 169 182 252 —
5,700 5,700 5,700 5,700 241 207 223 293 328
4,240 4,240 — — 182 147 — — —
4,870 4,870 4,870 4,870 208 186 201 309 —
5,700 5,700 5,700 5,700 241 228 246 359 416
7,770 7,770 7,770 — 328 — 295 375 416
9,500 9,500 9,290 — 396 — 376 452 446
10,710 — — — — 369† — — 529‡‡
12,550 — — — — 369† — — 529‡‡
8,290 — 8,290 8,290 350 — 311 396 437
10,140 — 10,140 9,910 422 — 396 477 469
11,420 — — — — 388† 284†† 363‡ 556‡‡
13,380 — — — — 388† 284†† 363‡ 556‡‡
9,840 — 9,840 9,840 416 — 326 424 459
12,040 — 12,040 11,770 501 — 416 512 493
13,560 — — — — — — — 584‡‡
15,890 — — — — — — — 584‡‡
11,400 — 11,400 11,400 481 — 388 503 547
13,940 — 13,940 13,620 580 — 495 606 587
15,710 — — — — 485† 354†† 454‡ 696‡‡
18,400 — — — — 485† 354†† 454‡ 696‡‡
— — 15,540 15,540 656 — 497 685 —
— — 19,000 18,580 791 — 634 826 —
— — 20,280 18,580 910 — 755 847 —
— — 20,280 18,580 1,060 — 905 847 —
† Hydril TS
†† Hydril FJ-P
‡ Hydril Super FJ-P
‡‡ Hydril Super EU.
Page 14

TABLE
DIMENSIONS AND
Thread & Cplg. Extreme Line
Wt. **
Size Per Ft. Inside Col’pse
O.D. Grade With Dia. Drift O.D. of Drift O.D. of Resis-
In. Cplg., In. Dia. Cplg. Dia. Box tance
Lb. In. In. In. In. PSI

51/2 *F-25 13.00 5.044 4.919 6.050 — — 1,660

H-40 14.00 5.012 4.887 6.050 — — 2,630
J-55 14.00 5.012 4.887 6.050 — — 3,120
J-55 15.50 4.950 4.825 6.050 4.653 5.860 4,040
J-55 17.00 4.892 4.767 6.050 4.653 5.860 4,910
K-55 14.00 5.012 4.887 6.050 — — 3,120
K-55 15.50 4.950 4.825 6.050 4.653 5.860 4,040
K-55 17.00 4.892 4.767 6.050 4.653 5.860 4,910
C-75 17.00 4.892 4.767 6.050 4.653 5.860 6,070
C-75 20.00 4.778 4.653 6.050 4.653 5.860 8,440
C-75 23.00 4.670 4.545 6.050 4.545 5.860 10,460
*C-75 26.00 4.548 — — 4.423 5.656 11,860
N-80 17.00 4.892 4.767 6.050 4.653 5.860 6,280
N-80 20.00 4.778 4.653 6.050 4.653 5.860 8,830
N-80 23.00 4.670 4.545 6.050 4.545 5.860 11,160
*N-80 26.00 4.548 — — 4.423 5.656‡ 12,650
C-95 17.00 4.892 4.767 6.050 4.653 5.860 6,930
C-95 20.00 4.778 4.653 6.050 4.653 5.860 10,000
C-95 23.00 4.670 4.545 6.050 4.545 5.860 12,920
*C-95 26.00 4.548 — — 4.423 5.656‡ 15,020
P-110 17.00 4.892 4.767 6.050 4.653 5.860 7,460
P-110 20.00 4.778 4.653 6.050 4.653 5.860 11,080
P-110 23.00 4.670 4.545 6.050 4.545 5.860 14,520
*P-110 26.00 4.548 — — 4.423 5.656‡ 17,390
*V-150 20.00 4.778 4.653 6.050 — — 13,480
*V-150 23.00 4.670 4.545 6.050 — — 18,390
*V-150 26.00 4.548 4.423 6.050 — — 23,720

*Non API Standard. Shown for information only.

** Collapse, Internal Yield and Joint Yield Strengths are minimum values with no
safety actor, reproduced by permission from API Bul. 5C2, Bulletin on
Performance Properties of Casing and Tubing.
 Page 15

NO. 203
STRENGTHS OF CASING
Internal Yield Pressure PSI** ** Joint Strength - 1000 Lbs.**
Body
Plain Round Thread Yield Threaded & Cplg. Joint
But- Ext.
End or Stgth. But-
tress Round Thread Line
Ext. 1,000 tress
Short Long Thd. Joint
Line Lbs. Short Long Thd.

— 1,810 — — 94 95 — — —
3,110 3,110 — — 161 130 — — —
4,270 4,270 — — 222 172 — — —
4,810 4,810 4,810 4,810 248 202 217 300 339
5,320 5,320 5,320 5,320 273 229 247 329 372
4,270 4,270 — — 222 189 — — —
4,810 4,810 4,810 4,810 248 222 239 366 429
5,320 5,320 5,320 5,320 273 252 272 402 471
7,250 — 7,250 7,250 372 — 327 423 471
8,610 — 8,610 8,430 437 — 403 497 497
9,900 — 9,260 8,430 497 — 473 550 549
11,360 — — — — 432† — — 678‡‡
7,740 — 7,740 7,740 397 — 348 446 496
9,190 — 9,190 8,990 466 — 428 524 523
10,560 — 9,880 8,990 530 — 502 579 577
12,120 — — — — 455† 315†† 451‡ 713‡‡
9,190 — 9,190 9,190 471 — 374 480 521
10,910 — 10,910 10,680 554 — 460 563 549
12,540 — 11,730 10,680 630 — 540 608 606
14,390 — — — — — — — 749‡‡
10,640 — 10,640 10,640 546 — 445 568 620
12,640 — 12,640 12,360 641 — 548 667 654
14,520 — 13,580 12,360 729 — 643 724 722
16,660 — — — — 569† 393†† 564‡ 892‡‡
— — 17,230 16,860 874 — 701 908 —
— — 18,520 16,860 994 — 823 910 —
— — 22,720 — — — — — 722‡

† Hydril TS
†† Hydril FJ-P
‡ Hydril Super FJ-P
‡‡ Hydril Super EU.
Page 16

TABLE
DIMENSIONS AND
Thread & Cplg. Extreme Line
Wt. **
Size Per Ft. Inside Col’pse
O.D. Grade With Dia. Drift O.D. of Drift O.D. of Resis-
In. Cplg., In. Dia. Cplg. Dia. Box tance
Lb. In. In. In. In. PSI

*6 F-25 15.00 5.524 5.399 6.625 — — 1,540

H-40 18.00 5.424 5.299 6.625 — — 2,780
J-55 18.00 5.424 5.299 6.625 — — 3,620
N-80 18.00 5.424 5.299 6.625 — — 4,740
N-80 20.00 5.352 5.227 6.625 — — 5,690
N-80 23.00 5.240 5.115 6.625 — — 7,180
P-110 23.00 5.240 5.115 6.625 — — 10,380
P-110 26.00 5.132 5.007 6.625 — — 12,380
65/8 *F-25 17.00 6.135 6.010 7.390 — — 1,370
H-40 20.00 6.049 5.924 7.390 — — 2,520
J-55 20.00 6.049 5.924 7.390 — — 2,970
J-55 24.00 5.921 5.796 7.390 5.730 7.000 4,560
K-55 20.00 6.049 5.924 7.390 — — 2,970
K-55 24.00 5.921 5.796 7.390 5.730 7.000 4,560
C-75 24.00 5.921 5.796 7.390 5.730 7.000 5,570
C-75 28.00 5.791 5.666 7.390 5.666 7.000 7,830
C-75 32.00 5.675 5.550 7.390 5.550 7.000 9,830
N-80 24.00 5.921 5.796 7.390 5.730 7.000 5,760
N-80 28.00 5.791 5.666 7.390 5.666 7.000 8,170
N-80 32.00 5.675 5.550 7.390 5.550 7.000 10,320
C-95 24.00 5.921 5.796 7.390 5.730 7.000 6,290
C-95 28.00 5.791 5.666 7.390 5.666 7.000 9,200
C-95 32.00 5.675 5.550 7.390 5.550 7.000 11,800
P-110 24.00 5.921 5.796 7.390 5.730 7.000 6,710
P-110 28.00 5.791 5.666 7.390 5.666 7.000 10,140
P-110 32.00 5.675 5.550 7.390 5.550 7.000 13,200

*Non API Standard. Shown for information only.

 Page 17

NO. 203
STRENGTHS OF CASING
Internal Yield Pressure PSI** ** Joint Strength - 1000 Lbs.**
Body
Plain Round Thread Yield Threaded & Cplg. Joint
But- Ext.
End or Stgth. But-
tress Round Thread Line
Ext. 1,000 tress
Short Long Thd. Joint
Line Lbs. Short Long Thd.

— 1,740 — — 107 108 — — —

— 3,360 — — 206 179 — — —
— 4,620 — — 283 239 279 — —
— — 6,720 — 412 — 323 — —
— — 7,560 — 461 — 366 — —
— — 8,870 — 536 — 432 — —
— — 12,190 — 737 — 565 — —
— — 13,920 — 833 — 646 — —
— 1,620 — — 123 121 — — —
3,040 3,040 — — 229 184 — — —
4,180 4,180 4,180 4,180 315 245 266 374 —
5,110 5,110 5,110 5,110 382 314 340 453 477
4,180 4,180 4,180 4,180 315 267 290 453 —
5,110 5,110 5,110 5,110 382 342 372 548 605
6,970 — 6,970 6,970 520 — 453 583 605
8,260 — 8,260 8,260 610 — 552 683 648
9,410 — 9,410 9,200 688 — 638 771 717
7,440 — 7,440 7,440 555 — 481 615 637
8,810 — 8,810 8,810 651 — 586 721 682
10,040 — 10,040 9,820 734 — 677 814 755
8,830 — 8,830 8,830 659 — 546 665 668
10,460 — 10,460 10,460 773 — 665 780 716
11,920 — 11 920 11,660 872 — 769 880 793
10,230 — 10,230 10,230 763 — 641 786 796
12,120 — 12,120 12,120 895 — 781 922 852
13,800 — 13,800 13,500 1,009 — 904 1,040 944

**Collapse, Internal Yield and Joint Yield Strengths are minimum values with no
safety factor, reproduced by permission from API Bul. 5C2, Bulletin on
Performance properties of Casing and Tubing.
Page 18

TABLE
DIMENSIONS AND
Thread & Cplg. Extreme Line
Wt. **
Size Per Ft. Inside Col’pse
O.D. Grade With Dia. Drift O.D. of Drift O.D. of Resis-
In. Cplg., In. Dia. Cplg. Dia. Box tance
Lb. In. In. In. In. PSI

7 *F-25 17.00 6.538 6.413 7.656 — — 1,100

H-40 17.00 6.538 6.413 7.656 — — 1,450
H-40 20.00 6.456 6.331 7.656 — — 1,980
J-55 20.00 6.456 6.331 7.656 — — 2,270
J-55 23.00 6.366 6.241 7.656 6.151 7.390 3,270
J-55 26.00 6.276 6.151 7.656 6.151 7.390 4,320
K-55 20.00 6.456 6.331 7.656 — — 2,270
K-55 23.00 6.366 6.241 7.656 6.151 7.390 3,270
K-55 26.00 6.276 6.151 7.656 6.151 7.390 4,320
C-75 23.00 6.366 6.241 7.656 6.151 7.390 3,770
C-75 26.00 6.276 6.151 7.656 6.151 7.390 5,250
C-75 29.00 6.184 6.059 7.656 6.059 7.390 6,760
C-75 32.00 6.094 5.969 7.656 5.969 7.390 8,230
C-75 35.00 6.004 5.879 7.656 5.879 7.530 9,710
C-75 38.00 5.920 5.795 7.656 5.795 7.530 10,680
N-80 23.00 6.366 6.241 7.656 6.151 7.390 3,830
N-80 26.00 6.276 6.151 7.656 6.151 7.390 5,410
N-80 29.00 6.184 6.059 7.656 6.059 7.390 7,020
N-80 32.00 6.094 5.969 7.656 5.969 7.390 8,600
N-80 35.00 6.004 5.879 7.656 5.879 7.530 10,180
N-80 38.00 5.920 5.795 7.656 5.795 7.530 11,390
C-95 23.00 6.366 6.241 7.656 6.151 7.390 4,150
C-95 26.00 6.276 6.151 7.656 6.151 7.390 5,870
C-95 29.00 6.184 6.059 7.656 6.059 7.390 7,820
C-95 32.00 6.094 5.969 7.656 5.969 7.390 9,730
C-95 35.00 6.004 5.879 7.656 5.879 7.530 11,640
C-95 38.00 5.920 5.795 7.656 5.795 7.530 13,420
P-110 26.00 6.276 6.151 7.656 6.151 7.390 6,210
P-110 29.00 6.184 6.059 7.656 6.059 7.390 8,510
P-110 32.00 6.094 5.969 7.656 5.969 7.390 10,760
P-110 35.00 6.004 5.879 7.656 5.879 7.530 13,010
P-110 38.00 5.920 5.795 7.656 5.795 7.530 15,110
*V-150 29.00 6.184 6.059 7.656 — — 9,800
*V-150 32.00 6.094 5.969 7.656 — — 13,020
*V-150 35.00 6.004 5.879 7.656 — — 16,230
*V-150 38.00 5.920 5.795 7.656 — — 19,240

*Non API Standard. Shown for information only.

 Page 19

NO. 203
STRENGTHS OF CASING
Internal Yield Pressure PSI** ** Joint Strength - 1000 Lbs.**
Body
Plain Round Thread Yield Threaded & Cplg. Joint
But- Ext.
End or Stgth. But-
tress Round Thread Line
Ext. 1,000 tress
Short Long Thd. Joint
Line Lbs. Short Long Thd.

— 1,440 — — 123 118 — — —

2,310 2,310 — — 196 122 — — —
2,720 2,720 — — 230 176 — — —
3,740 3,740 — — 316 234 — — —
4,360 4,360 4,360 4,360 366 284 313 432 499
4,980 4,980 4,980 4,980 415 334 367 490 506
3,740 3,740 — — 316 254 — — —
4,360 4,360 4,360 4,360 366 309 341 522 632
4,980 4,980 4,980 4,980 415 364 401 592 641
5,940 — 5,940 5,940 499 — 416 557 632
6,790 — 6,790 6,790 566 — 489 631 641
7,650 — 7,650 7,650 634 — 562 707 685
8,490 — 8,490 7,930 699 — 633 779 761
9,340 — 8,660 7,930 763 — 703 833 850
10,120 — 8,660 7,930 822 — 767 833 917
6,340 — 6,340 6,340 532 — 442 588 666
7,240 — 7,240 7,240 604 — 519 667 675
8,160 — 8,160 8,160 676 — 597 746 721
9,060 — 9,060 8,460 745 — 672 823 801
9,960 — 9,240 8,460 814 — 746 876 895
10,800 — 9,240 8,460 877 — 814 876 965
7,530 — 7,530 7,530 632 — 505 636 699
8,600 — 8,600 8,600 717 — 593 722 709
9,690 — 9,690 9,690 803 — 683 808 757
10,760 — 10,760 10,050 885 — 768 891 841
11,830 — 10,970 10,050 966 — 853 920 940
12,820 — 10,970 10,050 1,041 — 931 920 1,013
9,960 — 9,960 9,960 830 — 693 853 844
11,220 — 11,220 11,220 929 — 797 955 902
12,460 — 12,460 11,640 1,025 — 897 1,053 1,002
13,700 — 12,700 11,640 1,119 — 996 1,096 1,118
14,850 — 12,700 11,640 1,205 — 1,087 1,096 1,207
— — 15,300 15,300 1,267 — 1,049 1,296 —
— — 16,990 15,870 1,398 — 1,180 1,363 —
— — 17,320 15,870 1,526 — 1,311 1,363 —
— — 17,320 15,870 1,644 — 1,430 1,363 —

**Collapse, Internal Yield and Joint Yield Strengths are minimum values with no
safety factor, reproduced by permission from API Bul. 5C2, Bulletin on
Performance properties of Casing and Tubing.
Page 20

TABLE
DIMENSIONS AND
Thread & Cplg. Extreme Line
Wt. **
Size Per Ft. Inside Col’pse
O.D. Grade With Dia. Drift O.D. of Drift O.D. of Resis-
In. Cplg., In. Dia. Cplg. Dia. Box tance
Lb. In. In. In. In. PSI

75/8 *F-25 20.00 7.125 7.000 8.500 — — 1,100

H-40 24.00 7.025 6.900 8.500 — — 2,040
J-55 26.40 6.969 6.844 8.500 6.750 8.010 2,890
K-55 26.40 6.969 6.844 8.500 6.750 8.010 2,890
C-75 26.40 6.969 6.844 8.500 6.750 8.010 3,280
C-75 29.70 6.875 6.750 8.500 6.750 8.010 4,670
C-75 33.70 6.765 6.640 8.500 6.640 8.010 6,320
C-75 39.00 6.625 6.500 8.500 6.500 8.010 8,430
N-80 26.40 6.969 6.844 8.500 6.750 8.010 3,400
N-80 29.70 6.875 6.750 8.500 6.750 8.010 4,790
N-80 33.70 6.765 6.640 8.500 6.640 8.010 6,560
N-80 39.00 6.625 6.500 8.500 6.500 8.010 8,810
C-95 26.40 6.969 6.844 8.500 6.750 8.010 3,710
C-95 29.70 6.875 6.750 8.500 6.750 8.010 5,120
C-95 33.70 6.765 6.640 8.500 6.640 8.010 7,260
C-95 39.00 6.625 6.500 8.500 6.500 8.010 9,980
P-110 29.70 6.875 6.750 8.500 6.750 8.010 5,340
P-110 33.70 6,765 6.640 8.500 6.640 8.010 7,850
P-110 39.00 6.625 6.500 8.500 6.500 8.010 11,060
V-150 33.70 6.765 6.640 8.500 — — 8,860
V-150 39.00 6.625 6.500 8.500 — — 13,450
V-150 45.30 6.435 6.310 8.500 — — 19,680
85/8 *F-25 24.00 8.097 7.972 9.625 — — 950
H-40 28.00 8.017 7.892 9.625 — — 1,640
H-40 32.00 7.921 7.796 9.625 — — 2,210
J-55 24.00 8.097 7.972 9.625 — — 1,370
J-55 32.00 7.921 7.796 9.625 7.700 9.120 2,530
J-55 36.00 7.825 7.700 9.625 7.700 9.120 3,450
K-55 24.00 8.097 7.972 9.625 — — 1,370
K-55 32.00 7.921 7.796 9.625 7.700 9.120 2,530
K-55 36.00 7.825 7.700 9.625 7.700 9.120 3,450
C-75 36.00 7.825 7.700 9.625 7.700 9.120 4,020
C-75 40.00 7.725 7.600 9.625 7.600 9.120 5.350
C-75 44.00 7.625 7.500 9.625 7.500 9.120 6,680
C-75 49.00 7.511 7.386 9.625 7.386 9.120 8,200
N-80 36.00 7.825 7.700 9.625 7.700 9.120 4,100
N-80 40.00 7.725 7.600 9.625 7.600 9.120 5,520
N-80 44.00 7.625 7.500 9.625 7.500 9.120 6,950
N-80 49.00 7.511 7.386 9.625 7.386 9.120 8,570
C-95 36.00 7.825 7.700 9.625 7.700 9.120 4,360
C-95 40.00 7.725 7.600 9.625 7.600 9.120 6,010
C-95 44.00 7.625 7.500 9.625 7.500 9.120 7,730
C-95 49.00 7.511 7.386 9.625 7.386 9.120 9,690
P-110 40.00 7.725 7.600 9.625 7.600 9.120 6,380
P-110 44.00 7.625 7.500 9.625 7.500 9.120 8,400
P-110 49.00 7.511 7.386 9.625 7.386 9.120 10,720
*V-150 44.00 7.625 7.500 9.625 — — 9,640
*V-150 49.00 7.511 7.386 9.625 — — 12,950

*Non API Standard. Shown for information only.

 Page 21

NO. 203
STRENGTHS OF CASING
Internal Yield Pressure PSI** ** Joint Strength - 1000 Lbs.**
Body
Plain Round Thread Yield Threaded & Cplg. Joint
But- Ext.
End or Stgth. But-
tress Round Thread Line
Ext. 1,000 tress
Short Long Thd. Joint
Line Lbs. Short Long Thd.

— 1,430 — 145 138 — — — —

2,750 2,750 — 276 212 — — — —
4,140 4,140 4,140 4,140 414 315 346 483 553
4,140 4,140 4,140 4,140 414 342 377 581 700
5,650 — 5,650 5,650 564 — 461 624 700
6,450 — 6,450 6,450 641 — 542 709 700
7,400 — 7,400 7,400 729 — 635 806 766
8,610 — 8,610 8,610 839 — 751 929 851
6,020 — 6,020 6,020 602 — 490 659 737
6,890 — 6,890 6,890 683 — 575 749 737
7,900 — 7,900 7,900 778 — 674 852 806
9,180 — 9,180 9,180 895 — 798 981 896
7,150 — 7,150 7,150 714 — 560 716 774
8,180 — 8,180 8,180 811 — 659 813 774
9,380 — 9,380 9,380 923 — 772 925 846
10,900 — 10,900 10,900 1,063 — 914 1,065 941
9,470 — 9,470 9,470 940 — 769 960 922
10,860 — 10,860 10,860 1,069 — 901 1,093 1,008
12,620 — 12,620 12,620 1,231 — 1,066 1,258 1,120
— — 14,800 14,800 1,458 — 1,207 1,482 —
— — 17,210 17,210 1,679 — 1,428 1,706 —
— — 19,680 18,350 1,971 — 1,721 1,932 —
— 1,340 — 173 161 — — — —
2,470 2,470 318 233 — — — —
2,860 2,860 366 279 — — — —
2,950 2,950 381 244 — — — —
3,930 3,930 3,930 3,930 503 372 417 579 686
4,460 4,460 4,460 4,460 568 434 486 654 688
2,950 2,950 — — 381 263 — — —
3,930 3,930 3,930 3,930 503 402 452 690 869
4,460 4,460 4,460 4,460 568 468 526 780 871
6,090 — 6,090 6,090 775 — 648 847 871
6,850 — 6,850 6,850 867 — 742 947 942
7,610 — 7,610 7,610 957 — 834 1,046 1,007
8,480 — 8,480 8,480 1,059 — 939 1,157 1,007
6,490 — 6,490 6,490 827 — 688 895 917
7,300 — 7,300 7,300 925 — 788 1,001 992
8,120 — 8,120 8,120 1,021 — 887 1,105 1,060
9,040 — 9,040 9,040 1,129 — 997 1,222 1,060
7,710 — 7,710 7,710 982 — 789 976 963
8,670 — 8,670 8,670 1,098 — 904 1,092 1,042
9,640 — 9,640 9,640 1,212 — 1,017 1,206 1,113
10,740 — 10,740 10,740 1,341 — 1,144 1,334 1,113
10,040 — 10,040 10,040 1,271 — 1,055 1,288 1,240
11,160 — 11,160 11,160 1,404 — 1,186 1,423 1,326
12,430 — 12,430 12,430 1,553 — 1,335 1,574 1,326
— — 15,220 15,220 1,914 — 1,591 1,925 —
— — 16,950 16,950 2,118 — 1,789 2,130 —

**Collapse, Internal Yield and Joint Yield Strengths are minimum values with no
safety factor, reproduced by permission from API Bul. 5C2, Bulletin on
Performance properties of Casing and Tubing.
Page 22

TABLE
DIMENSIONS AND
Thread & Cplg. Extreme Line
Wt. **
Size Per Ft. Inside Col’pse
O.D. Grade With Dia. Drift O.D. of Drift O.D. of Resis-
In. Cplg., In. Dia. Cplg. Dia. Box tance
Lb. In. In. In. In. PSI

95/8 *F-25 29.30 9.063 8.907 10.625 — — 860

H-40 32.30 9.001 8.845 10.625 — — 1,400
H-40 36.00 8.921 8.765 10.625 — — 1,740
J-55 36.00 8.921 8.765 10.625 — — 2,020
J-55 40.00 8.835 8.679 10.625 8.599 10.100 2,570
K-55 36.00 8.921 8.765 10.625 — — 2,020
K-55 40.00 8.835 8.679 10.625 8.599 10.100 2,570
C-75 40.00 8.835 8.679 10.625 8.599 10.100 2,980
C-75 43.50 8.755 8.599 10.625 8.599 10.100 3,750
C-75 47.00 8.681 8.525 10.625 8.525 10.100 4,630
C-75 53.50 8.535 8.379 10.625 8.379 10.100 6,380
N-80 40.00 8.835 8.679 10.625 8.599 10.100 3,090
N-80 43.50 8.755 8.599 10.625 8.599 10.100 3,810
N-80 47.00 8.681 8.525 10.625 8.525 10.100 4,750
N-80 53.50 8.535 8.379 10.625 8.379 10.100 6,620
C-95 40.00 8.835 8.679 10.625 8.599 10.100 3,330
C-95 43.50 8.755 8.599 10.625 8.599 10.100 4,130
C-95 47.00 8.681 8.525 10.625 8.525 10.100 5,080
C-95 53.50 8.535 8.379 10.625 8.379 10.100 7,330
P-110 43.50 8.755 8.599 10.625 8.599 10.100 4.430
P-1110 47.00 8.681 8.525 10.625 8.525 10.100 5,310
P-110 53.50 8.535 8.379 10.625 8.379 10.100 7,930
*V-150 53.50 8.535 8.379 10.625 — — 8,970
*V-150 58.40 8.435 8.279 10.625 — — 11,570
*V-150 61.10 8.375 8.219 10.625 — — 13,130
*V-150 71.80 8.125 7.969 10.625 — — 19,640
103/4 *F-25 32.75 10.192 10.036 11.750 — — 650
H-40 32.75 10.192 10.036 11.750 — — —
H-40 40.50 10.050 9.894 11.750 — — 1,420
J-55 40.50 10.050 9.894 11.750 — — 1,580
J-55 45.50 9.950 9.794 11.750 9.794 11.460 2,090
J-55 51.00 9.850 9.694 11.750 9.694 11.460 2,700
K-55 40.50 10.050 9.894 11.750 — — 1,580
K-55 45.50 9.950 9.794 11.750 9.794 11.460 2,090
K-55 51.00 9.850 9.694 11.750 9.694 11.460 2,700
C-75 51.00 9.850 9.694 11.750 9.694 11.460 3,100
C-75 55.50 9.760 9.604 11.750 9.604 11.460 3,950
N-80 51.00 9.850 9.694 11.750 9.694 11.460 3,220
N-80 55.50 9.760 9.604 11.750 9.604 11.460 4,020
C-95 51.00 9.850 9.694 11.750 9.694 11.460 3,490
C-95 55.50 9.760 9.604 11.750 9.604 11.460 4,300
P-110 51.00 9.850 9.694 11.750 9.694 11.460 3,670
P-110 55.50 9.760 9.604 11.750 9.604 11.460 4,630
P-110 60.70 9.660 9.504 11.750 9.504 11.460 5,860
P-110 65.70 9.560 9.404 11.750 — — 7,490
*P-110 71.10 9.450 9.294 11.750 — — 9,280
*V-150 65.70 9.560 9.404 11.750 — — 8,330
*V-150 71.10 9.450 9.294 11.750 — — 10,890

*Non API Standard. Shown for information only.

 Page 23

NO. 203
STRENGTHS OF CASING
Internal Yield Pressure PSI** ** Joint Strength - 1000 Lbs.**
Body
Plain Round Thread Yield Threaded & Cplg. Joint
But- Ext.
End or Stgth. But-
tress Round Thread Line
Ext. 1,000 tress
Short Long Thd. Joint
Line Lbs. Short Long Thd.

— 1,280 — 206 185 — — — —

2,270 2,270 — 365 254 — — — —
2,560 2,560 — 410 294 — — — —
3,520 3,520 3,520 3,520 564 394 453 639 —
3,950 3,950 3,950 3,950 630 452 520 714 770
3,520 3,520 3,520 3,520 564 423 489 755 —
3,950 3,950 3,950 3,950 630 486 561 843 975
5,390 — 5,390 5,390 859 — 694 926 975
5,930 — 5,930 5,930 942 — 776 1,016 975
6,440 — 6,440 6,440 1,018 — 852 1,098 1,032
7,430 — 7,430 7,430 1,166 — 999 1,257 1,173
5,750 — 5,750 5,750 916 — 737 979 1,027
6,330 — 6,330 6,330 1,005 — 825 1,074 1,027
6,870 — 6,870 6,870 1,086 — 905 1,161 1,086
7,930 — 7,930 7,930 1,244 — 1,062 1,329 1,235
6,820 — 6,820 6,820 1,088 — 847 1,074 1,078
7,510 — 7,510 7,510 1,193 — 948 1,178 1,078
8,150 — 8,150 8,150 1,289 — 1,040 1,273 1,141
9,410 — 9,410 9,410 1,477 — 1,220 1,458 1,297
8,700 — 8,700 8,700 1,381 — 1,106 1,388 1,283
9,440 — 9,440 9,440 1,493 — 1,213 1,500 1,358
10,900 — 10,900 10,900 1,710 — 1,422 1,718 1,544
— — 14,860 14,860 2,332 — 1,909 2,321 —
— — 16,230 16,230 2,532 — 2,098 2,519 —
— — 17,050 16,560 2,651 — 2,211 2,638 —
— — 18,060 16,560 3,136 — 2,672 2,692 —
— 1,140 — — 229 196 — — —
1,820 1,820 — — 367 205 — — —
2,280 2,280 — — 457 314 — — —
3,130 3,130 — 3,130 629 420 — 700 —
3,580 3,580 — 3,580 715 493 — 796 975
4,030 4,030 — 4,030 801 565 — 891 1,092
3,130 3,130 — 3,130 629 450 — 819 —
3,580 3,580 — 3,580 715 528 — 931 1,236
4,030 4,030 — 4,030 801 606 — 1,043 1,383
5,490 5,490 — 5,490 1,092 756 — 1,160 1,383
6,040 6,040 — 6,040 1,196 843 — 1,271 1,515
5,860 5,860 — 5,860 1,165 804 — 1,228 1,456
6,450 6,450 — 6,450 1,276 895 — 1,345 1,595
6,960 6,960 — 6,960 1,383 927 — 1,354 1,529
7,660 7,660 — 7,660 1,515 1,032 — 1,483 1,675
8,060 8,060 — 8,060 1,602 1,080 — 1,594 1,820
8,860 8,860 — 8,860 1,754 1,203 — 1,745 1,993
9,760 9,760 — 9,760 1,922 1,338 — 1,912 2,000
10,650 10,650 — 10,650 2,088 1,472 — 2,077 —
— 11,240 — 10,980 2,269 1,618 — 2,418 —
— 14,530 — 14,530 2,847 1,978 — 2,799 —
— 15,330 — 14,970 3,094 2,174 — 2,957 —

**Collapse, Internal Yield and Joint Yield Strengths are minimum values with no
safety factor, reproduced by permission from API Bul. 5C2, Bulletin on
Performance properties of Casing and Tubing.
Page 24

TABLE
DIMENSIONS AND
Thread & Cplg. Extreme Line
Wt. **
Size Per Ft. Inside Col’pse
O.D. Grade With Dia. Drift O.D. of Drift O.D. of Resis-
In. Cplg., In. Dia. Cplg. Dia. Box tance
Lb. In. In. In. In. PSI

113/4 *F-25 38.00 11.150 10.994 12.750 — — 620

H-40 42.00 11.084 10.928 12.750 — — 1,070
J-55 47.00 11.000 10.844 12.750 — — 1,510
J-55 54.00 10.880 10.724 12.750 — — 2,070
J-55 60.00 10.772 10.616 12.750 — — 2,660
K-55 47.00 11.000 10.844 12.750 — — 1,510
K-55 54.00 10.880 10.724 12.750 — — 2,070
K-55 60.00 10.772 10.616 12.750 — — 2,660
C-75 60.00 10.772 10.616 12.750 — — 3,070
N-80 60.00 10.772 10.616 12.750 — — 3,180
C-95 60.00 10.772 10.616 12.750 — — 3,440
133/8 *F-25 48.00 12.715 12.559 14.375 — — 560
H-40 48.00 12.715 12.559 14.375 — — 770
J-55 54.50 12.615 12.459 14.375 — — 1,130
J-55 61.00 12.515 12.359 14.375 — — 1,540
J-55 68.00 12.415 12.259 14.375 — — 1,950
K-55 54.50 12.615 12.459 14.375 — — 1,130
K-55 61.00 12.515 12.359 14.375 — — 1,540
K-55 68.00 12.415 12.259 14.375 — — 1,950
C-75 72.00 12.347 12.191 14.375 — — 2,590
*C-75 77.00 12.275 12.119 14.375 — — 2,990
*C-75 85.00 12.159 12.003 14.375 — — 3,810
*C-75 98.00 11.937 11.781 14.375 — — 5,720
N-80 72.00 12.347 12.191 14.375 — — 2,670
*N-80 77.00 12.275 12.119 14.375 — — 3,100
N-80 85.00 12.159 12.003 14.375 — — 3,870
*N-80 98.00 11.937 11.781 14.375 — — 5,910
C-95 72.00 12.347 12.191 14.375 — — 2,820
*P-110 72.00 12.347 12.191 14.375 — — 2,880
*V-150 72.00 12.347 12.191 14.375 — — 2,880
16 *F-25 55.00 15.376 15.188 17.000 — — 290
H-40 65.00 15.250 15.062 17.000 — — 670
J-55 75.00 15.124 14.936 17.000 — — 1,020
J-55 84.00 15.010 14.822 17.000 — — 1,410
K-55 75.00 15.124 14.936 17.000 — — 1,020
K-55 84.00 15.010 14.822 17.000 — — 1,410
*K-55 109.00 14.688 14.500 17.000 — — 2,560
*C-75 109.00 14.688 14.500 17.000 — — 2,980
*N-80 109.00 14.688 14.500 17.000 — — 3,080

*Non API Standard. Shown for information only.

 Page 25

NO. 203
STRENGTHS OF CASING
Internal Yield Pressure PSI** ** Joint Strength - 1000 Lbs.**
Body
Plain Round Thread Yield Threaded & Cplg. Joint
But- Ext.
End or Stgth. But-
tress Round Thread Line
Ext. 1,000 tress
Short Long Thd. Joint
Line Lbs. Short Long Thd.

— 1,120 — — 270 222 — — —

1,980 1,980 — — 478 307 — — —
3,070 3,070 — 3,070 737 477 — 807 —
3,560 3,560 — 3,560 850 568 — 931 —
4,010 4,010 — 4,010 952 649 — 1,042 —
3,070 3,070 — 3,070 737 509 — 935 —
3,560 3,560 — 3,560 850 606 — 1,079 —
4,010 4,010 — 4,010 952 693 — 1,208 —
5,460 5,460 — 5,460 1,298 869 — 1,361 —
5,830 5,830 — 5,830 1,384 924 — 1 440 —
6,920 6,920 — 6,920 1,644 1,066 — 1,596 —
— 1,080 — — 338 260 — — —
1,730 1,730 — — 541 322 — — —
2,730 2,730 — 2,730 853 514 — 909 —
3,090 3,090 — 3,090 962 595 — 1,025 —
3,450 3,450 — 3,450 1,069 675 — 1,140 —
2,730 2,730 — 2,730 853 547 — 1,038 —
3,090 3,090 — 3,090 962 633 — 1,169 —
3,450 3,450 — 3,450 1,069 718 — 1,300 —
5,040 5,040 — 5,040 1,558 978 — 1,598 —
— 5,400 — 5,400 1,662 1,054 — 2,054 —
— 5,970 — 5,970 1,829 1,177 — 2,261 —
— 6,270 — 6,120 2,144 1,408 — 2,296 —
5,380 5,380 — 5,380 1,661 1,040 — 1,693 —
— 5,760 — 5,760 1,773 1,122 — 2,148 —
— 6,360 — 6,360 1,951 1,252 — 2,364 —
— 6,680 — 6,530 2,287 1,498 — 2,400 —
6,390 6,390 — 6,390 1,973 1,204 — 1,893 —
— 7,400 — 7,400 2,596 1,402 — 2,433 —
— 10,090 — 10,090 3,323 1,887 — 2,976 —
— 850 — — 384 258 — — —
1,640 1,640 — — 736 439 — — —
2,630 2,630 — 2,630 1,178 710 — 1,200 —
2,980 2,980 — 2,980 1,326 817 — 1,351 —
2,630 2,630 — 2,630 1,178 752 — 1,331 —
2,980 2,980 — 2,980 1,326 865 — 1,499 —
— 3,950 — 3,950 1,739 1,181 — 1,962 —
— 5,380 — — 2,372 1,499 — — —
— 5,740 — — 2,530 1,594 — — —

**Collapse, Internal Yield and Joint Yield Strengths are minimum values with no
safety factor, reproduced by permission from API Bul. 5C2, Bulletin on
Performance properties of Casing and Tubing.
Page 26

TABLE
DIMENSIONS AND
Thread & Cplg. Extreme Line
Wt. **
Size Per Ft. Inside Col’pse
O.D. Grade With Dia. Drift O.D. of Drift O.D. of Resis-
In. Cplg., In. Dia. Cplg. Dia. Box tance
Lb. In. In. In. In. PSI

185/8 H-40 87.50 17.755 17.567 19.625 — — 630

J-55 87.50 17.755 17.567 19.625 — — 630
K-55 87.50 17.755 17.567 19.625 — — 630
20 *F-25 94.00 19.124 18.936 21.000 — — 410
H-40 94.00 19.124 18.936 21.000 — — 520
J-55 94.00 19.124 18.936 21.000 — — 520
J-55 106.50 19.000 18.812 21.000 — — 770
J-55 133.00 18.730 18.542 21.000 — — 1,500
K-55 94.00 19.124 18.936 21.000 — — 520
K-55 106.50 19.000 18.812 21.000 — — 770
K-55 133.00 18.730 18.542 21.000 — — 1,500

*Non API Standard. Shown for information only.

 Page 27

NO. 203
STRENGTHS OF CASING
Internal Yield Pressure PSI** ** Joint Strength - 1000 Lbs.**
Body
Plain Round Thread Yield Threaded & Cplg. Joint
But- Ext.
End or Stgth. But-
tress Round Thread Line
Ext. 1,000 tress
Short Long Thd. Joint
Line Lbs. Short Long Thd.

1,630 1,630 — — 994 559 — — —

2,250 2,250 — — 1,367 754 — 1,329 —
2,250 2,250 — — 1,367 794 — 1,427 —
— 960 — — 673 359 — — —
1,530 1,530 — — 1,077 581 — — —
2,110 2,110 2,110 — 1,480 784 907 1,402 —
2,410 2,410 2,410 — 1,685 913 1,057 1,596 —
3,060 3,060 3,060 — 2,125 1,192 1,380 2,012 —
2,110 2,110 2,110 — 1,480 824 955 1,479 —
2,410 2,410 2,410 — 1,685 960 1,113 1,683 —
3,060 3,060 3,060 — 2,125 1,253 1,453 2,123 —

**Collapse, Internal Yield and Joint Yield Strengths are minimum values with no
safety factor, reproduced by permission from API Bul. 5C2, Bulletin on
Performance properties of Casing and Tubing.
Page 28
TABLE 204

STRETCH DATA FOR DRILL PIPE,

TUBING AND CASING
Stretch Per Pull Above Stretch
Length 1000 Lb. Weight of Due To Own
Size of of Pipe Pull Above Pipe Per Weight
Tubing, D.P. Suspended Wt. of Pipe, In. Stretch Suspended
or Casing in Well, Inches of Pipe in Water,
Feet Factor C Pounds Inches

500 .115 6,450 .14

2.375” 1,000 .310 3,225 .56
2,000 .620 1,612 2.22
Upset
3,000 .930 1,075 5.00
Tubing
4.70 #/Ft. 4,000 1.240 806 8.88
5,000 1.550 644 13.88
10,000 3.100 322 55.51
500 .110 9,080 .14
1,000 .220 4,540 .56
2.875” 2,000 .440 2,270 2.22
Upset 3,000 .660 1,513 5.00
Tubing
6.50 #/Ft. 4,000 .880 1,135 8.88
5,000 1.100 908 13.88
10,000 2.200 454 55.51
500 .0772 12,960 .14
1,000 .1544 6,480 .56
3.500” 2,000 .3088 3,240 2.22
Upset 3,000 .4632 2,160 5.00
Tubing
9.30 #/Ft. 4,000 .6176 1,620 8.88
5,000 .7720 1,296 13.88
10,000 1.544 648 55.51
500 .070 14,300 .14
1,000 .140 7,150 .56
2.875” 2,000 .280 3,575 2.22
Drill Pipe 3,000 .420 2,383 5.00
10.40 #/Ft. 4,000 .560 1,787 8.88
5,000 .700 1,430 13.88
10,000 1.40 715 55.51

FORMULA FOR DETERMINING STRETCH IN PIPE

L X P X C
S=
1000 X 1000
(use to set tension packer with no weight indication)

FORMULA FOR DETERMINING PULL OF PIPE

1000 X 1000 X S
P=
C X L

FORMULA FOR FREE PIPE DEPTH

S X 1000 X 1000
L=
P X C

Where: L = Length of free pipe in feet.

S = Stretch pulled in pipe, in inches.
P = Pull on pipe to get the stretch “S” in pounds
C = Constant for given pipe size and weight being stretched.
(For this equation use C factor at pipe length of 1000 ft.)
 Page 29
TABLE 204

STRETCH DATA FOR DRILL PIPE,

TUBING AND CASING
Stretch Per Pull Above Stretch
Length 1000 Lb. Weight of Due To Own
Size of of Pipe Pull Above Pipe Per Weight
Tubing, D.P. Suspended Wt. of Pipe, In. Stretch Suspended
or Casing in Well, Inches of Pipe in Water,
Feet Factor C Pounds Inches

500 .055 18,200 .14

3.500” 1,000 .110 9,100 .56
2,000 .220 4,550 2.22
Drill Pipe
3,000 .330 3,033 5.00
13.30 #/Ft.
4,000 .440 2,275 8.88
5,000 .550 1,820 13.88
10,000 1.10 910 55.51
500 .0450 22,200 .14
1,000 .0900 11,100 .56
4.500” 2,000 .180 5,550 2.22
Drill Pipe 3,000 .270 3,700 5.00
16.60 #/Ft.
4,000 .360 2,775 8.88
5,000 .450 2,220 13.88
10,000 .900 1,110 55.51
500 .0402 24,800 .14
1,000 .0804 12,400 .56
5.500” 2,000 .160 6,230 2.22
Casing 3,000 240 4,133 5.00
17 #/Ft.
4,000 .320 3,100 8.88
5,000 .402 2,480 13.88
10,000 804 1,240 55.51
500 .0301 33,220 .14
1,000 .0602 16,610 .56
7.000” 2,000 .120 8,305 2.22
Casing 3,000 .181 5,537 5.00
23 #/Ft. 4,000 241 4,152 8.88
5,000 .301 3,322 13.88
10,000 .602 1,661 55.51
NOTE: The above figures apply only to steel pipe that has not been stretched or is
not being stretched beyond its elastic limit.

Example:
A 7” RTTS is set at 15,000 feet on 2 3/8: 4.7 #/ft. EUE tubing. There are
indications that the casing has collapsed above the tool. Pick up pipe weight,
mark pipe and pull 20,000 pounds above pipe weight. This 20,000 pounds
stretches pipe 25 inches. Where is the casing collapsed?

S = 25 inches

P = 20,000 pounds

C = .31 (C factor from table at 1000 ft.)

25 X 1000 X 1000
L=
20,000 X .31
L = 4032 feet
Page 30
TABLE 205

SLACK-OFF DATA FOR TUBING

AND DRILL PIPE
Size of Tubing or Drill Pipe Slack-Off Factor*

1.900 O.D. EUE Tubing 0.68

2.375 O.D. EUE Tubing 0.39
2.875 O.D. EUE Tubing 0.26
3.500 O.D. EUE Tubing 0.17
2.875 O.D. 10.40 lb/ft DP 0.16
3.500 O.D. 13.30 lb/ft DP 0.12
4.500 O.D. 16.60 lb/ft DP 0.10
* Inches to slack-off to obtain 1000 lbs. weight on packer for each 1000 ft. of depth.
An allowance is included for coiling and friction.

Desired Weight Packer Depth

Required slack (inc.) = X X Factor
1000 1000

Example:
Weight desired on packer ......................................... 15,000 lbs.
Depth packer set ............................................................. 5,000:”
Size of Tubing ........................................................ 2.375” EUE
Slack-off factor for 2.375” EUE from table = 0.39

15,000 5,000
X X 0.39 = 29.25 (use 29 inches)
1000 1000

The setting stroke required to set any particular tool is not included in these figures
and will have to be added.

NOTE: The above figures apply only to pipe that has not been stretched, or is not
being stretched beyond its elastic limit.
 Page 31

TUBING

API Non-Upset Tubing

Sizes: 1.050” - 41/2”

API External Upset Tubing

Sizes: 1.050” - 41/2”

Extreme-Line Tubing
Sizes: 23/8” - 31/2”
Page 32

CASING
API SHORT OR LONG

Round-Thread Casing
Sizes: 41/2” - 20”
(21/2” and 241/2”)

API Buttress-Thread Casing

Sizes: 41/2” - 20”

API Extreme-Line Casing

Sizes: 5” - 103/4”