Scribd
Upload
130 views2 pages

PN11 - Deluge Pump

This document provides a technical specification for a foam deluge pump. The pump has a capacity of 320 cubic meters per hour, a total head of 12.02 bar, and is powered by a 161.28 kW electric motor running at 1791 rpm. The pump casing is made of bronze, has a 250/200 mm suction/pressure flange, and other key components including a duplex stainless steel shaft and nitrile mechanical seal. The pump is rated to a maximum working pressure of 13.5 bar and was tested according to classification society requirements.

Uploaded by

Fayez Al-ahmadi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
130 views2 pages

PN11 - Deluge Pump

This document provides a technical specification for a foam deluge pump. The pump has a capacity of 320 cubic meters per hour, a total head of 12.02 bar, and is powered by a 161.28 kW electric motor running at 1791 rpm. The pump casing is made of bronze, has a 250/200 mm suction/pressure flange, and other key components including a duplex stainless steel shaft and nitrile mechanical seal. The pump is rated to a maximum working pressure of 13.5 bar and was tested according to classification society requirements.

Uploaded by

Fayez Al-ahmadi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Technical Specification

Foam Deluge Pump, 1Set


General Information
Quotation No. CM-4874 Pos. No. 7
Pump NSL200-525/D02-N
Pump Type Vertical Inline Centrifugal Pump Pump series NSL Density 1.025 kg/l
Pump Media Sea water Pump Model NSL200-525 Viscosity 1.00 cSt

Pump data Motor Data


Capacity 320.00 m³/h Brand Manufacturers standard
Total Man. Head 12.02 bar Motor ABB + 220V/60Hz space heater
Speed 1791 rpm Power Supply Electric motor 3 x 480V - 60Hz +- 5%
Power Consumption 161.28 kW Construction T.E.F.C
NPSHr 4.09 mLC Insulation Cl. F-IP55
Non-Overl. Power 220.70 kW Motor Speed 1791 rpm
Eta 66.22 % Performance 230.00 kW Soft Start@55℃
Delivered by DESMI A/S

Max. working pressure; being the pressure at the suction branch and the maximum generated head at zero flow. For this
particular pump in standard material: 13.5 bar ( =134.3 mLC with a density of 1.025 kg/l )
If higher working pressure is required other materials are available upon request.
Test pressure; pump approved by classification societies have been pressure tested according to the requirements of these
societies, i. a test pressure of 1,5 x working pressure.
The test pressure is stated in the test certificate and stamped on the discharge flange of the pump.

Specification:
Pump Casing Bronze (RG5)
Suction/Pressure Flange 250/200 mm.
Impeller NiAlBz DS/EN 1982 CC333
Impeller Diameter 499.00 mm
Shaft Duplex Stainless Steel AISI 329
Mechanical Shaft Seal NITRIL Ø85
Bearings Ball Bearings
Coupling Monobloc(Rigid coupling without spacer)
Rotation Clockwise
Manometer Gauge board(-1/+15Bar) pre-mounted
Class Society ABS
Max grain size 22.00

(C) DESMI - WinPSP 2014 Pump Selection Program - Version 3.85 (16.04.2014) - DB: 343 (14.04.2014)
Foam Deluge Pump
7
According to ISO 9906 Grade 2B

(1) NSL200-525 Speed: 1791 rpm, Imp. Dia: 499.0 mm, Density: 1.025 kg/l

You might also like