SWAB CUPS
MEDIUM LOAD
The Petro rubber MEDIUM load swab cup is and all
purpose, all rubber cup designed to perform well over a
wide range of lifting demands. The three smaller lips allow
the cup to load up under less fluid while the larger lips
provide extra lifting capacity. It is molded out of the same
abrasion resistant rubber as the heavy load cups, versatile
swab cup that delivers exceptional results in most swabbing
situations.
CPP PART # DESCRIPTION
SWCUP-PM2.38-A 2-3/8” (60.33 mm) Aluminium Core Cups
SWCUP-PM2.78-A 2-7/8” (73.03 mm) Aluminium Core Cups
SWCUP-PM3.50-A 3-1/2” (83.0 mm) Aluminium Core Cups
SWCUP-PM2.38-S 2-3/8” (60.33 mm) Steel Core Cups
SWCUP-PM2.78-S 2-7/8” (73.03 mm) Steel Core Cups
SWCUP-PM3.50-S 3-1/2” (83.0 mm) Steel Core Cups
SAND CUPS
The Petro Rubber SAND swab cups is an all rubber cup
designed to run in wells with a high ratio of suspended sand
or solids. The multiple lips seal easily but allow solids to
pass by the swab assembly while still maintaining a
positive seal. This action eliminates the build up of solids
on top of the swab assembly, thereby minimizing the
chance of getting stuck. This cup is also effective in wells
with worn or damaged tubing where maintaining seal with
the swab cup is difficult. Molded out of the same abrasion
resistant rubber as our other swabbing products, this cup
will stand up to the worst of tubing.
CPP PART # DESCRIPTION
SWCUP-PS2.38-A 2-3/8” (60.33 mm) Aluminium Core Cups
SWCUP-PS2.78-A 2-7/8” (73.03 mm) Aluminium Core Cups
SWCUP-PS3.50-A 3-1/2” (83.0 mm) Aluminium Core Cups
SWCUP-PS2.38-S 2-3/8” (60.33 mm) Steel Core Cups
SWCUP-PS2.78-S 2-7/8” (73.03 mm) Steel Core Cups
SWCUP-PS3.50-S 3-1/2” (83.0 mm) Steel Core Cups
Canadian Pump & Packing Co. Ltd.
9804 – 54 Avenue, Edmonton AB T6E 0A9
Phone: 780-438-0483 Fax: 780-435-5143 Toll-Free: 1-800-871-4160
www.cdnpumpandpack.ca
LIGHT LOAD
The Petro rubber LIGHT Load cup is an all rubber cup
designed to lift lighter loads. The multiple flexible lips seal
easily and maintain a seal so that small amounts of fluid
can be lifted. Another benefit of this design is the ability to
control the suction below the swab assembly as it is pulled
up the tubing. This minimizes the amount of sand being
sucked into the well bore and reduces the potential for
damage to fragile formations.
CPP PART # DESCRIPTION
SWCUP-PL2.38-A 2-3/8” (60.33 mm) Aluminium Core Cups
SWCUP-PL2.78-A 2-7/8” (73.03 mm) Aluminium Core Cups
SWCUP-PL3.50-A 3-1/2” (83.0 mm) Aluminium Core Cups
SWCUP-PL2.38-S 2-3/8” (60.33 mm) Steel Core Cups
SWCUP-PL2.78-S 2-7/8” (73.03 mm) Steel Core Cups
SWCUP-PL3.50-S 3-1/2” (83.0 mm) Steel Core Cups
HEAVY LOAD
The Petro Rubber HEAVY load swab cup is our high
performance, all rubber cup designed for maximum lifting
capacity and extra long life. It is molded out of Petro
Rubbers Extremely tough, abrasion resistant rubber
compound. Formulated specifically for swabbing at high
swabbing speed, deep wells, rough tubing, whatever the
conditions, this best all rubber swab cup you can use.
CPP PART # DESCRIPTION
SWCUP-PH2.38-A 2-3/8” (60.33 mm) Aluminium Core Cups
SWCUP-PH2.78-A 2-7/8” (73.03 mm) Aluminium Core Cups
SWCUP-PH3.50-A 3-1/2” (83.0 mm) Aluminium Core Cups
SWCUP-PH2.38-S 2-3/8” (60.33 mm) Steel Core Cups
SWCUP-PH2.78-S 2-7/8” (73.03 mm) Steel Core Cups
SWCUP-PH3.50-S 3-1/2” (83.0 mm) Steel Core Cups
Canadian Pump & Packing Co. Ltd.
9804 – 54 Avenue, Edmonton AB T6E 0A9
Phone: 780-438-0483 Fax: 780-435-5143 Toll-Free: 1-800-871-4160
www.cdnpumpandpack.ca
WIRE CUPS
The Petro Rubber WIRE swab cups are our strongest and
most durable swab cup. We mold the same tough rubber
compound used to make heavy load cups. Molded onto a
spring steel wire insert that provided extra strength and
reinforcement while swabbing.. These cups are designed
for maximum load lifting capability and to stand up to
extreme swabbing conditions. Wire cups show their
obvious superiority when used at higher speeds, deeper
wells or in extremely worn tubing.
CPP PART # DESCRIPTION
SWCUP-PW2.38-A 2-3/8” (60.33 mm) Aluminium Core Cups
SWCUP-PW2.78-A 2-7/8” (73.03 mm) Aluminium Core Cups
SWCUP-PW3.50-A 3-1/2” (83.0 mm) Aluminium Core Cups
SWCUP-PW2.38-S 2-3/8” (60.33 mm) Steel Core Cups
SWCUP-PW2.78-S 2-7/8” (73.03 mm) Steel Core Cups
SWCUP-PW3.50-S 3-1/2” (83.0 mm) Steel Core Cups
CASING SWAB CUPS
Especially designed to lift fluid containing a high ratio of
suspended sand. Also suitable for lifting ordinary light
loads with minimum suction across the sand face. Number
of cups used may vary depending on the operator to fit the
conditions.
Available in the following Sizes:
CPP PART # DESCRIPTION
SWCUP-C4.50 4-1/2” (114.3 mm) Casing Swab Cups
SWCUP-C5.50 5-1/2” (139.7 mm) Casing Swab Cups
SWCUP-C7.00 7” (177.8 mm) Casing Swab Cups
Canadian Pump & Packing Co. Ltd.
9804 – 54 Avenue, Edmonton AB T6E 0A9
Phone: 780-438-0483 Fax: 780-435-5143 Toll-Free: 1-800-871-4160
www.cdnpumpandpack.ca
ROD WIPERS
Used to prevent the escape of oil and gas when rods are being pulled or run in. Cleans the rods
and coupling from oil and paraffin and prevents tools and dies from being dropped down the
hole. Especially compounded for long life with flexibility and durability.
CPP PART # SIZE
SWROD-5/8 5/8” ROD WIPERS
SWROD-3/4 3/4” ROD WIPERS
SWROD-7/8-1 7/8-1” ROD WIPERS
OIL SAVER RUBBERS
CPP PART # SIZE
TYPE H
SWOIL-H9/16 3/8”–5/8” - 9/16” Type H Oilsavers
SWOIL-H5/16 5/16” Type H Oilsavers
SWOIL-H7/16 7/16” Type H Oilsavers
**Blue Oil Saver rubbers available for low temperatures**
CPP PART # SIZE
DOUBLE EE
SWOIL-E5/16 5/16” Type EE Oilsavers
SWOIL-E9/16 3/8” – 5/8” (9/16) Double EE
SWOIL-E5/16-T410 5/16 Double EE - Type 410
SWOIL-E9/16-T410 3/8”–5/8” (9/16) Double EE-Type 410
Canadian Pump & Packing Co. Ltd.
9804 – 54 Avenue, Edmonton AB T6E 0A9
Phone: 780-438-0483 Fax: 780-435-5143 Toll-Free: 1-800-871-4160
www.cdnpumpandpack.ca
BOP RAM RUBBERS
(Blowout Preventer)
GUIBERSON TYPE
2-3/8" X 7-1/16"
2-7/8" X 7-1/16"
3-1/2" X 7-1/16"
BLIND (CSO)
LOW TEMPERATURE
CAMERON QRC TYPE
SAFETY & STRIPPING RAMS
2-3/8" X 7-1/16"
2-7/8" X 7-1/16"
3-1/2" X 7-1/16"
BLIND (CSO)
TOP SEALS
SHAFFER SENTINEL TYPE
SENTINEL TYPE I & II
2-3/8" X 7-1/16"
2-7/8" X 7-1/16"
3-1/2" X 7-1/16"
BLIND (CSO)
TOP SEALS
LOW TEMPERATURE
SHAFFER TYPE 61 LWS
2-3/8" X 7-1/16"
2-7/8" X 7-1/16"
3-1/2" X 4-1/16"
BLIND (CSO)
LOW TEMPERATURE
SHAFFER TYPE 64 TYPE LWP
2-3/8" X 7-1/16" 3-1/2" X 9"
2-7/8" X 7-1/16" 4" X 9"
3-1/2" X 7-1/16" 4-1/2" X 9"
BLIND (CSO)
LOW TEMPERATURE
SHAFFER TYPE 39
2-3/8" X 7-1/16"
2-7/8" X 7-1/16"
3-1/2" X 7-1/16"
BLIND (CSO)
Canadian Pump & Packing Co. Ltd.
9804 – 54 Avenue, Edmonton AB T6E 0A9
Phone: 780-438-0483 Fax: 780-435-5143 Toll-Free: 1-800-871-4160
www.cdnpumpandpack.ca
JU PACKOFF RUBBERS (GUIBERSON TYPE)
CPP PART # SIZE
SWPAK-1.660-JU 1.660"
SWPAK-1.990-JU 1.990"
SWPAK-2-3/8-JU 2-3/8"
SWPAK-2-7/8-JU 2-7/8"
SWPAK-3-1/2-JU 3-1/2"
ANNULAR BOPS - HYDRIL TYPE
3000# 7-1/16" NITRILE OR NATURAL
5000# 7-1/16" NITRILE OR NATURAL
BOPS - REGAN TYPE
3" TYPE K 3000# Units
O-RING KITS
REGAN TYPE K BOP REPLACEMENT RUBBERS
CPP PART # SIZE
SWBOP-REGAN-225K 2-1/4" Hourglass
SWBOP-REGAN-300K 3" Full Opening
SWBOP-REGAN-400K 4" Full Opening
SWBOP-REGAN-500K 5” Full Opening
Canadian Pump & Packing Co. Ltd.
9804 – 54 Avenue, Edmonton AB T6E 0A9
Phone: 780-438-0483 Fax: 780-435-5143 Toll-Free: 1-800-871-4160
www.cdnpumpandpack.ca
TUBING DRIFTS WITH LIFTING EYES
CPP PART # SIZE
SWTUB-2-3/8 2-3/8"
SWTUB-2-7/8 2-7/8"
SWTUB-3-1/2 3-1/2"
WIRELINE STRIPPERS
BJ Type - Available with or without Chains
The wireline stripper automatically adjusts itself to the line,
tightening its grip by lengthening of the spiral wiping
element. The wiper is quickly applied to the line and kicks
off by unwinding when the rope socket makes contact.
CPP PART # STYLE
SWIRE-CHAIN With Chains
SWIRE-NOCHN Without Chains
ROPE SOCKETS & SWIVELS
Available in 1/2" & 9/16"
Rope Sockets and Swivels can be sold separately.
Also available 1" Swivel complete with Eye bolt.
CPP PART # STYLE
SWROP-SO&SW-1/2 1/2" Rope Socket & Swivel Complete
SWROP-SO&SW-C Rope Socket & Swivel Complete
SWROP-SOCK Socket Only
SWROP-SWIV Swivel Only
Canadian Pump & Packing Co. Ltd.
9804 – 54 Avenue, Edmonton AB T6E 0A9
Phone: 780-438-0483 Fax: 780-435-5143 Toll-Free: 1-800-871-4160
www.cdnpumpandpack.ca
SEAL RINGS (For Hammer Unions)
GUIBERSON TYPE
CPP PART # SIZE
SEAL-GRING-100 1”
SEAL-GRING-150 1-1/2”
SEAL-GRING-200 2”
SEAL-GRING-4.00 4”
WECO TYPE
CPP PART # SIZE
SEAL-WRING-100 1”
SEAL-WRING-100V 1” VITON
SEAL-WRING-150 1-1/2”
SEAL-WRING-150V 1-1/2” VITON
SEAL-WRING-200 2”
SEAL-WRING-200V 2” VITON
SEAL-WRING-300 3”
SEAL-WRING-300V 3” VITON
SEAL-WRING-400 4”
SEAL-WRING-400V 4” VITON
Guiberson Seal Rings Weco Seal Rings
Seal rings are also available in HSN
Canadian Pump & Packing Co. Ltd.
9804 – 54 Avenue, Edmonton AB T6E 0A9
Phone: 780-438-0483 Fax: 780-435-5143 Toll-Free: 1-800-871-4160
www.cdnpumpandpack.ca
