Scribd
Upload
139 views4 pages

Embroidery Machine Setup Guide

This document provides instructions for setting the mass cam on an embroidery machine. It involves: 1) Disassembling the mass cam driving box cover and mass cam bolts. 2) Manually moving the mass cam to align with the roller while the main shaft is at 100 degrees. 3) Tightening the mass cam screw when the movable mass moves 2-3 times with the main shaft at 293 degrees. 4) Reassembling the cover once the mass cam is correctly set.

Uploaded by

Flavio Sanchez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
139 views4 pages

Embroidery Machine Setup Guide

This document provides instructions for setting the mass cam on an embroidery machine. It involves: 1) Disassembling the mass cam driving box cover and mass cam bolts. 2) Manually moving the mass cam to align with the roller while the main shaft is at 100 degrees. 3) Tightening the mass cam screw when the movable mass moves 2-3 times with the main shaft at 293 degrees. 4) Reassembling the cover once the mass cam is correctly set.

Uploaded by

Flavio Sanchez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

SWF EMBROIDERY MACHINE M-SU-A0-05-03

TR-30-M-ENG CD CODE No:

[E] Bed [Rotary Hook Base]

A. Contents Mass Cam Setting

Jig / Measurement
B. Overview No. Procedure Tools Required
Devices

1 Cover Disassembly Phillips Screwdriver


2 Mass Cam Bolt Disassembly 3mm T-wrench
3 Mass Cam Setting 3mm T-wrench, Phillips Screwdriver
4 Cover Assembly Phillips Screwdriver

C. Procedure -Mass Cam Setting-

Mass Cam Screw


1. Cover Disassembly
1) Disassemble Mass Cam Driving Box Cover Screws. (2 places)

2. Mass Cam Bolt Disassembly[Refer to Figure 5-1]


1) Disassemble Mass Cam Screws. (3 places)

Figure 5-1

3. Mass Cam Setting


Solenoid 1) Manually operate Solenoid Crank move Mass Cam to Roller.
Crank
(Main Shaft Angle 100˚) [Refer to Figure 5-2,3]

Mass Cam

Roller

Mass Driving Crank

Mass Cam

Mass Driving Lever


Mass Driving Lever
Figure 5-2 Figure 5-3

─ Ver.2010 1st ────────────────────── SunStar Precision Co., Ltd ─


SWF EMBROIDERY MACHINE M-SU-A0-05-03

Mass Cam

2) Set Main Shaft Angle at 293˚.


3) After locating the point where the Movable Mass moves
2 - 3 times by manually operating the Mass Cam, tighten Mass
Cam Screw. (1 place only)
[Refer to Figure 5-4,5]

CAUTION) Verify that Mass Cam is placed tightly to


Bearing side. If not, it may result in problems in angle
Figure 5-4 changes or thread not being cutting.
Movable Mass

4) Manually rotate the Main Shaft to be at 293˚ to verify the Movable


Mass moves.
If the Movable Mass moves before or after 293˚,
repeat steps 2) to 4). [Refer to Figure 5-5]

5) Assemble the remaining Mass Cam Bolts.

4. Mass Cam Driving Box Cover Assembly


1) Assemble Mass Cam Driving Box Cover.

Fixed Mass

Figure 5-5

─ Ver.2010 1st ────────────────────── SunStar Precision Co., Ltd ─


SWF EMBROIDERY MACHINE M-SU-A0-05-03

─ Ver.2010 1st ────────────────────── SunStar Precision Co., Ltd ─


SWF EMBROIDERY MACHINE M-SU-A0-05-03

˚ to verify the Movable

─ Ver.2010 1st ────────────────────── SunStar Precision Co., Ltd ─

You might also like