3.
3 LIST OF TOOLS, EQUIPMENT AND MATERIALS PLUMBING NC II
Recommended list of tools, equipment and materials for the training of 25 trainees for
Plumbing NC II.
TOOLS
Qty Description Qty Description Qty Description
6 pcs. Pipe wrench 4 Pipe Vise 1” – 4” (2 5 pcs Mechanical Plier
(2 pcs each sizes units Yoke vise and 2 chain
10”, 12” ,14”) vise)
5 pcs. Pressure gauges 5 pcs. Pipe Cutter ½” – 2” 6 pcs Adjustable wrench
(3” dia. X ¼” dia. (3each 10” & 12”)
0-300 psi)
25 pcs. Steel Tape (5m) 25 Ballpeen Hammer 5 pcs. Flat Screw Driver 10”
pcs.
25 pcs Hacksaw with Blade 25 Pointed Cold Chisel 5 pcs. Philip Screw Driver
pcs (various length 10” -12”) 10”
5 pcs. Spirit level bar 24” 5 pcs. Electrical Plier 25 Cold Chisel (var.
length pcs lengths 8”-12” dia.
5/8”)
5 units Pipe Reamer 5 pcs Plumb Bob (Std. size)
EQUIPMENT
Qty Description Qty Description Qty Description
1 unit Threading Machine 1 set Cutting outfit set (Harris 1 unit Welding machine 300
complete with the or Morris) with oxygen / amperes with
following 220 V acetylene cylinder with grounding and
2 units Die head gas content (refillable) extension cable,
2 sets dies (1/2” & electrode holder and
¾” – 1” – 2”) welding mask.
1 pc pipe reamer
1 pc pipe cutter
2 units Fusion Machine 2 Electric Grinder (4”) 1 unit Electric Test Pump
(20mm – 32mm) units
2 units Electric Drill (drill bit 1 unit Push Drill ¼” – 5/8” size 5 Blow Torch
¼” – 5/8”) units
2 units Manual Test Pump 5 Portable Soldering Kit 1 unit
Cut-off machine (14”
cylind dia. cutting disc )
ers
MATERIALS and CONSUMABLES
Qty Description Qty Description Qty Description
SANITARY, WASTE AND COLD WATER SUPPLY AND CONSUMABLES
VENT SYSTEM DISTRIBUTION PIPING
8 PVC Pipe 6” m x 3m PVC BLUE PIPES AND 6 sets Plumbing Blue - print
lengths s-1000 FITTINGS plan
16 PVC Pipe 4” m x 3m 5 pcs. PVC Blue pipe 1” x 3 6 pcs Paint brush 9 3 each,
lengths s-1000 mtrs. 1” & 1 ½”)
TR PLUMBING NC II (Amended) Promulgated October 2014 Page 76
5 PVC Pipe 3”m x 3”m 5 pcs. PVC Tee Reducer 1” x 10 Sand Paper (12” x
lengths s-1000 ½” sheets 12” rough)
30 PVC Pipe 2”m x 3”m 25 PVC Blue Pipe ½” x 10’ 6 pcs Chalk Stone
length s-1000 pcs
5 pcs PVC Wye 6” x 4” 150 PVC Tee ½” x ½” 1 pad Writing Paper
pcs
12 pcs PVC Wye 4” x 4” 150 PVC Tee Female ½” x 2 kls Welding Rod ( each
pcs ½” 6011 and 6013 x 1/8”
15 pcs PVC Wye 4” x 2” 150 PVC Elbow ½” x 90˚ 2 kls G.I. Wire # 18
pcs
10 pcs PVC Tee 4” x 2” 75 PVC Elbow Female ½” PPR PIPES AND FITTINGS
pcs x 90˚
40 pcs PVC Tee 2” x 2” 75 PVC Cap ½” 5 pcs PPR Pipe 32mm x 4
pcs mtrs.
12 pcs PVC Elbow 4” x 90˚ 100 PVC Male Adapter ½” 25 PPR Pipes 20mm x
pcs pcs 20mm
35 pcs PVC Elbow 2” x 90˚ 100 PVC Female Adapter 25 PPR Gate Valve
pcs ½” pcs 20mm
10 pcs PVC Elbow 4” x 45˚ 150 Teflon Tape 150 PPR Tee Equal
rolls pcs 20mm x 20mm
20 pcs PVC Elbow 2” x 45˚ 200 G.I Plug ½” 225 PPR Tee Female
pcs pcs 20mm x ½”
5 pcs PVC Elbow 3” x 90˚ 25 Gate Valve ½” 150 PPR Equal Elbow
pcs Screwed Type pcs 20mm x 90º
15 pcs PVC P- Trap 2” G.I. PIPES AND FITTINGS 75 PPR Elbow Female
pcs 20mm x ½” x 90º
5 pcs PVC Cleanout 4” 5 pcs G.I. Pipe 1” x 6 mtrs. 75 PPR End Cap 20mm
pcs
4 cans PVC Solvent 5 pcs. G.I. Tee Reducer 1” x 150 PPR Male Adapter
Cement 400cc ½” pcs ½”
5 unit PVC Wye 4” x 3” 13 G.I. Pipe ½” x 20 sch. 150 PPR Female Adapter
pcs 40 pcs ½”
10 pcs PVC Wye 3” x 2” 25 Gate Valve ½” - 5 pcs. PPR Tee Reducer
pcs Screwed Type 32mm x 20mm
10 pcs PVC Elbow 3” x 45˚ 75 G.I. Tee ½” x ½” 25 Single shower valve
pcs pcs.
5 pcs PVC Cleanout 3” 100 G.I. Elbow ½” x 90º
pcs
75 G.I. Cap ½”
pcs
175 G.I. Plug ½”
pcs
PLUMBING FIXTURES
5 units Water Meter 1 set Bath Tub with complete
fittings
5 units Water Closet (Flush 1 set Urinal with push-button
Tank) with Bidet or flush valve and
Spray complete fittings
TR PLUMBING NC II (Amended) Promulgated October 2014 Page 77
5 sets Lavatory with faucet 2 Grease trap, 4 gpm
units capacity
5 sets Kitchen Sink with
faucet
2 units Multipoint water
heater
15 pcs Floor drains
10 sets Faucets
3.4 TRAINING FACILITIES
Based on a class intake of 25 students/trainees
SPACE REQUIREMENT SIZE IN METERS AREA IN TOTAL AREA IN
SQ. METERS SQ. METERS
Student/Trainee Working 5x8 40 40
Space
Lecture Room/Demo 5x5 25 25
Room
Wash Room 2x5 10 10
Tool Room 5x5 25 25
Laboratory Area 5 unit – 2 x 4 40 40
Facilities/Equipment/ 6x7 42 42
Circulation area
Workshop Area 10 x 18 180
TR PLUMBING NC II (Amended) Promulgated October 2014 Page 78
