JCY-1800/1850

VDR/S-VDR

CYC-316A Playback Software /

Real Time Monitor
Instruction Manual
Version 2.0

For further information,contact:

Not use the asbestos

URL http://www.jrc.co.jp
Marine Service Department
Telephone : +81-3-3492-1305
Facsimile : +81-3-3779-1420
e-mail : [email protected]
AMSTERDAM Branch
Telephone : +31-20-658-0750
Facsimile : +31-20-658-0755
e-mail : [email protected]
SEATTLE Branch
Telephone : +1-206-654-5644
Facsimile : +1-206-654-7030
e-mail : [email protected]
CODE No.7ZPJD0378C 01ETM ISO 9001, ISO 14001 Certified
MAY. 2008 Edition 1 JRC Printed in Japan
 Introduction

＜Introduction＞

Thank you for using the Playback software for our VDR/S-VDR equipment. This software is intended to help

analyze the data recordings that are stored in a CF card of VDR/S-VDR installed onboard.

This software chronologically plays back all the data including the radar image, bridge and VHF

communication audios recorded in VDR/S-VDR.

- Before using the software, read this manual thoroughly to ensure correct use.

- Keep the manual in a convenient location so that it can be used easily whenever necessary.

- Use this manual to check the operation of the software or at the occurrence of a fault.

Microsoft, MS-DOS, and Windows are the registered trademarks of Microsoft Corporation in the U.S.A and /

or other countries.

Pentium is the trademark of Intel Corporation.

The names of actual companies and products mentioned herein are the trademarks of their respective

owners.

Attention

(1) The copyright of this software and a manual is in Japan Radio Co., Ltd.

(2) The range as which the Copyright Act determines a part or all of the contents of this software

and a manual cannot be exceeded, and it cannot reproduce without notice.

(3) Although we created to make doubly sure about the contents of this book, if there is a thing of

companion mind, such as a doubtful point, and an error, omission in written, please contact me.

(4) Please understand beforehand that it is not concerned with (3) clauses and any responsibility

cannot be taken about the claim of the loss for reasons of the employed result, loss profits, etc. in

our company.

Playback Software / Real Time Monitor Instruction Manual

i
Before Using

＜Before Using＞
Icons

This manual and product employ various icons to enable users to use the product safety and

correctly, and to prevent any harm to users or others, and to prevent damage to the property.

The icons and the meanings are indicated below.

Incorrect use of the equipment by ignoring this icon may cause death or a
WARNING seruous injury.

Incorrect use of the equipment by ignoring this icon may cause an injury or
CAUTION
physical damage.

Example of icons
The △ symbole indicates a caution (including danger or warning).

Inside of the symbol indicates the actual details (this icon indicates the

caution regarding electric shock).

Electric
shock

The symbol indicates prohibition.

The actual contents (this icon indicates “disassembly prhibited”) are provided

inside or alongside of the symbol

Disassembly
prohibited Prohibited

The ● symbol indicates an action or insutruction. The actual contenst (this

icon indicates removal of the power plug from socket) are provided inside of
Remove
Plug Instruction the symbol

Playback Software / Real Time Monitor Instruction Manual

ii
 Notes on Using

< Notes on Using >

Do not disassemble or remodel this equipment.

Such action may cause fire, electric shock, or an equipment fault.

Do not use any AC/DC adaptor other than attachment.

Such action may cause fire, electric shock, or an equipment fault.

Do not use any power supply voltage other than the specified voltages.

Such action may cause fire, electric shock, or an equipment fault.

Do not use any battery other than specification..

Such action may cause burst of a battery by liquid leak, fire, or injury.

Do not put containers into which it went, such as water, or a small metal thing on this

equipment top or near.

When water enters or a metal thing falls into the equipment, it becomes the cause of a fire, an

electric shock, and failure.

Do not damage a power cord or process it.

If put a heavy thing, heat, it pulls or it bends by force, a power cord will be damaged and it

may become the cause of fire and electric shock.

When a fault occurs, turn off the power supply of this equipment, remove the plug, and

contact the Sales Department of Japan Radio Company, nearest branch company, branch

office, sales office, or our agent.

Continuous use may cause fire or electric shock.

Do not check or repair the inside of the equipment by yourself.

Checking or repair by anyone other than the specialist maintenance staff may cause fire or

electric shock.

Request checking or repair of the inside of the equipment to the sales Department of Japan

Radio Company, nearest branch company, branch office, sales office, or our agent.

Playback Software / Real Time Monitor Instruction Manual

iii
Notes on Using

CAUTION
Do not install the equipment in the location affected by water, humidity, dust, or soot. It may

become the cause of fire, electric shock, or a fault.

Do not put in from a vent foreign substance, such as metal or a thing which is easy to burn.

It may become the cause of fire, electric shock, or a fault.

Do not put on a place with many vibration and shocks.

It may fall and may become the cause of an injury and failure.

Do not wet this equipment or do not put in water.

It may become the cause of electric shock, or a fault.

Do not plug up the vent of this equipment.

It may be filled with heat and fire and failure may occur.

When the equipment is not used for a long time, pull out a power supply plug from a wall

socket for safety.

It may become the cause of fire or electric shock.

Pull out a plug from a wall socket for safety at the time of care.

It may become the cause of fire or electric shock.

Be careful of a computer virus.

If a computer is infected with a virus, it may suffer the damage of an unusual display, a

program, and data being destroyed, and may become the cause of failure.

Please confirm whether it is infected with the computer virus, using a virus checker program

periodically.

Playback Software / Real Time Monitor Instruction Manual

iv
 Contents

＜Contents＞

＜Introduction＞............................................................................................................. i

＜Before Using＞ .......................................................................................................... ii

< Notes on Using > ...................................................................................................... iii

Chapter1 Outline........................................................................................................... 1

Chapter2 Install Playback software............................................................................. 3

2.1 PC specification...................................................................................................................................3

2.2 How to install .......................................................................................................................................4

2.3 How to uninstall .................................................................................................................................21

Chapter3 Setup for Playback software ..................................................................... 23

3.1 Create a playback folder....................................................................................................................23

3.2 Set required information for playback with the Setup software..........................................................23

Chapter4 Operation .................................................................................................... 29

4.1 How to start up Playback software ....................................................................................................29

4.2 How to exit Playback software...........................................................................................................30

4.3 Playback screen ................................................................................................................................31

4.4 Playback Operation Panel .................................................................................................................33

4.5 To play back CF card data.................................................................................................................34

4.6 To start playback, and to stop ............................................................................................................37

4.7 To set playback time ..........................................................................................................................37

4.7.1 Setting playback time by Slide bar ..............................................................................................37

4.7.2 Setting playback time by [Forward] button or [Rewind] button ....................................................38

4.7.3 Setting playback time by [Clock] button ......................................................................................38

Playback Software / Real Time Monitor Instruction Manual

v
Contents

4.8 To change a playback speed .............................................................................................................39

4.9 To adjust Volume and select audio source ........................................................................................40

4.10 Voyage screen.................................................................................................................................41

4.10.1 Graphic screen .........................................................................................................................42

4.10.2 Numeric screen.........................................................................................................................48

4.11 Alarm/Status screen.........................................................................................................................49

4.12 Radar screen...................................................................................................................................50

4.12.1 Icon ...........................................................................................................................................51

4.12.2 Menu bar...................................................................................................................................51

4.13 AIS Screen....................................................................................................................................52

4.13.1 Graphic screen .........................................................................................................................53

4.13.2 List screen ................................................................................................................................55

4.13.3 Detail Information of own ship...................................................................................................56

4.13.4 Detail information of AIS target .................................................................................................57

4.14 To confirm the record sentences in the NMEA format .....................................................................58

4.15 To print screen .................................................................................................................................60

4.16 To confirm the VDR/S-VDR system information ..............................................................................61

4.17 How to customize screen layout......................................................................................................63

4.18 How to restore to initial screen layout..............................................................................................67

4.19 Optional Function ............................................................................................................................68

4.19.1 Real Time Indication .................................................................................................................68

4.19.2 Record for a Long Time ............................................................................................................69

4.19.2.1 Record Setup .........................................................................................................................69

4.19.2.2 Record Start ...........................................................................................................................71

4.19.2.3 Record Stop or Pause............................................................................................................72

4.19.2.4 To playback recorded data .....................................................................................................73

Playback Software / Real Time Monitor Instruction Manual

vi
 Contents

Chapter5 Converting Recorded Data into Industry Standard Formats.................. 75

5.1 Starting conversion software..........................................................................................................75

5.2 Convert all recorded data...............................................................................................................76

5.3 Converting a part of recorded data ................................................................................................79

5.4 C onverted files (Industry Standard Formats Files) ........................................................................81

Chapter6 Trouble Shooting........................................................................................ 83

Chapter7 Appendix ..................................................................................................... 85

7.1 How to eject CF card from VDR/S-VDR ............................................................................................85

7.2 Sentence and indication place...........................................................................................................87

Playback Software / Real Time Monitor Instruction Manual

vii
Contents

Blank Page

Playback Software / Real Time Monitor Instruction Manual

viii
 Chapter1 Outline

Chapter1 Outline
This software intends to be used for playing back recorded data required the International Standard in a

CF card of VDR/S-VDR equipment.

Record data

・Sensor data

・Bridge audio and VHF communication

・Radar image

As an optional function, this software is extended as real time monitor by making LAN connection with

VDR/S-VDR. And real time data can be indicated and recorded by Real Time Monitor side for a long

time, and the data can be played back.

Further as an expanded function, by connecting with shipboard LAN, you can see the Real Time

Monitor in a sitting room.

In the case of requirement, contact the Sales Department of Japan Radio Company, nearest branch

company, branch office, sales office, or our agent.

Playback Software / Real Time Monitor Instruction Manual

1
Chapter1 Outline

Blank Page

Playback Software / Real Time Monitor Instruction Manual

2
 Chapter2 Install Playback software

Chapter2 Install Playback software

2.1 PC specification
Confirm the following system requirement on your PC.

OS : Windows XP Professional or Home Edition

Windows Vista (SP1)

CPU : Minimum Pentium M Processor730 1.6GHz or Higher

RAM : Minimum 512MB (XP)

Minimum 1GB(Vista)

HDD : Minimum 40GB

Display Resolution : 1024×768 dots (Recommend XGA)

CD drive : CD-ROM

Card drive : PCMCIA TypeⅡ or CF Card

Network : 10BASE-T/100BASE-TX Ethernet

Playback Software / Real Time Monitor Instruction Manual

3
Chapter2 Install Playback software

2.2 How to install

Install the Playback software in a PC in accordance with the following operation.

(1) Insert the Install CD-ROM in a CD drive.

(2) After a while, Installer starts and the following web screen opens automatically by AUTORUN.

To continue installation, please operate from (4).

(If the installer does not start, click “SetupE.exe” after selecting the CD drive by My Computer.

And then operate from (3). For the instruction on how to install on Windows Vista PC, refer

to Note on next page. )

The following contents are possible to refer in the web screen.

Note ・ Playback Software / Real Time Monitor instruction manual

・ CSV Conversion instruction manual

・ JCY-1800 VDR instruction manual

・ JCY-1850 S-VDR instruction manual
・ CD license number

Playback Software / Real Time Monitor Instruction Manual

4
 Chapter2 Install Playback software

The Instruction of how to install on Windows Vista

Note ・ In order to install Playback Software, always login PC as
administrator, and execute the installation.

・ Insert Installation CD-ROM in CD drive. After a while, AUTORUN

function starts up and the following screen displays. Select “Open

folder to view files.”

Open folder to view

files

・Run SetupE.exe in the folder by left-clicking it, then the following

confirmation screen for execution displays. Select ”Allow” by

left-clicking it, then the installer starts up.

Allow

(3) The preparation for the installation are started.

Playback Software / Real Time Monitor Instruction Manual

5
Chapter2 Install Playback software

(4) The opening screen is indicated, and click [Next] button.

(5) The Install Shield Wizard for the Playback software starts, and click [Next] button.

(6) Customer Information screen is indicated.

Please enter user information in the User Name field and the Organization field.
And enter the License number, which is described in the install CD-ROM to the Serial Number

field.

Note License number is composed by “jrc－＊＊＊＊－＊＊＊＊”.

Playback Software / Real Time Monitor Instruction Manual

6
 Chapter2 Install Playback software

(7) The confirmation screen where the installation folder and user information are shown is

indicated, and click [Install] button.

(8) Install is started, and progress bar is indicated.

(9) The Install Shield Wizard completion screen is indicated, and click [Finish] button.

(10) Please eject the Install CD-ROM from the CD drive, and keep the Installation CD-ROM

carefully.

(11) Since Playback software partially uses network communication, disable the firewall function
on your PC in accordance with the following procedure.

Playback Software / Real Time Monitor Instruction Manual

7
Chapter2 Install Playback software

●For Windows XP

・Click [Start] button, and then click “Control Panel” in Start menu.

Control Panel

・Click “Network and Internet Connection”.

Network and Internet

Connection

・Click “Windows Firewall”

Windows Firewall

・Select “Off (not recommended)”, and click [OK] button.

Off (not recommended)

Playback Software / Real Time Monitor Instruction Manual

8
 Chapter2 Install Playback software

●For Windows Vista

・Click [Start] button and then click “Control Panel”.

Control Panel

・Click “Security”.

Security

・Click “Turn Windows Firewall on or off”.

Turn Windows Firewall

on or off

・Select “Off (not recommended)”, and click [OK] button.

Off (not recommended)

Playback Software / Real Time Monitor Instruction Manual

9
Chapter2 Install Playback software

(12) Set power option so that your PC does not enter system standby (sleep) or hibernation while

operating Playback software.

●For Windows XP

・Click “Performance and Maintenance” on Control Panel screen.

Performance and Maintenance

・Click “Power Option”.

Power Option

・Select ”Never” under “Plugged in” of “Turn off hard disks”, “System standby”, and

“Hibernation” on “Power Schemes” tab and click [OK] button.

Never

Playback Software / Real Time Monitor Instruction Manual

10
 Chapter2 Install Playback software

●For Windows Vista

・Click “System and Maintenance” on Control Panel screen.

System and Maintenance

・Click “Change when computer sleeps”.

Change when computer sleeps

・Click “Change advanced power setting”.

Change advanced power

setting

Playback Software / Real Time Monitor Instruction Manual

11
Chapter2 Install Playback software

・Select ”Never” for ” Plugged in” of “Hard disk”, “Sleep after”, and “Hibernate after” and click

[OK] button.

Hard disk

Sleep after

Hibernate after

Playback Software / Real Time Monitor Instruction Manual

12
 Chapter2 Install Playback software

(13) For notebook or laptop PC, set as follows so that PC does not enter sleep mode when closing

the lid.

●For Windows XP

・Click “Performance and Maintenance” on Control Panel screen.

Performance and Maintenance

・Click “Power Option”.

Power Option

・Select “Advance” tab.

Select “Do nothing” under “When I close the lid of my portable computer” and click [OK]

button.

Advance tab

When I close the lid of my

portable computer

Playback Software / Real Time Monitor Instruction Manual

13
Chapter2 Install Playback software

●For Windows Vista

・Click “Mobile PC” on Control Panel screen.

Mobile PC

・Click “Change what closing the lid does”.

Change what closing

the lid does

・Select “Do nothing” under “Plugged in” of “When I close the lid” and click [Save changes]

button.

When I close the lid

Playback Software / Real Time Monitor Instruction Manual

14
 Chapter2 Install Playback software

(14) If the operating system (OS) on your PC is not Japanese or English version, Playback

software might not display correctly.

Please set language to "English (United States)" or "English (United Kingdom)" as follows.

●For Windows XP

・Click “Date, Time, Language, and Regional Options” on Control Panel screen.

Date, Time, Language,

and Regional Options

・Click “Regional and Language Options”.

Regional and Language

Options

Playback Software / Real Time Monitor Instruction Manual

15
Chapter2 Install Playback software

・Select “Regional Option” tab and select “English (United States)” or “English (United

Kingdom)”.

Regional Option tab

English (United States) or

English (United Kingdom)

・Select “Advanced” tab.

Select “English (United States)” or “English (United Kingdom)” ”, then click [OK] button.
You will be asked to restart Windows, and then restart it.

Advance tab

English (United States) or

English (United Kingdom)

Playback Software / Real Time Monitor Instruction Manual

16
 Chapter2 Install Playback software

●For Windows Vista

・Click “Clock, Language, and Region” on Control Panel screen.

Clock, Language, and

Region

・Click “Regional and Language Options”.

Regional and Language

Options

Playback Software / Real Time Monitor Instruction Manual

17
Chapter2 Install Playback software

・Select “Format” tab and select “English (United States)” or “English (United Kingdom)”.

Format tab

English (United States) or

English (United Kingdom)

・Select “Administrator” tab.

Click [Change system locale] button, and select “English (United States)” or “English

(United Kingdom)”, and then click [OK] button.

You will be asked to restart Windows, and then restart it.

Administrator tab

[Change system locale] button

Playback Software / Real Time Monitor Instruction Manual

18
 Chapter2 Install Playback software

(15) For Windows Vista PC, since Playback software has to start by the administrator user

continually, set as follows.

・Right-click the “JCY-1800 VDR Monitor” icon on desktop.

・Select “Properties”.

Properties

・Select “Compatibility” tab.

Compatibility tab

Playback Software / Real Time Monitor Instruction Manual

19
Chapter2 Install Playback software

・Input “✓” mark in “Run this program as an administrator” under “Privilege Level”, and click [OK]

button.

Privilege Level

The setup for Windows Vista PC is completed above.

After installation also, always login as administrator user and use

Note Playback software.

In addition, since the confirmation screen is displayed at starting

Playback software, select "Allow" and start the software.

Allow

Playback Software / Real Time Monitor Instruction Manual

20
 Chapter2 Install Playback software

2.3 How to uninstall

Uninstall the Playback software in your PC in accordance with the below operation.

●For Windows XP

・Click [Start] button and click “Control Panel” in Start menu.

Control Panel

・Click “Add or Remove Programs”.

Add or Remove
Programs

・Select the JCY-1800 VDR Monitor and click [Remove] button.

JCY-1800

VDR Monitor

・Since some files remain in the installation folder after completing the uninstallation, open My

Computer and delete the folder.

Installation folder: C:\Program files\JRC\JCY1800\VDR_Monitor

Playback Software / Real Time Monitor Instruction Manual

21
Chapter2 Install Playback software

●For Windows Vista

・Click [Start] button and click “Control Panel” in Start menu.

Control Panel

・Click “Uninstall a program”.

Uninstall a program

・Click “JCY-1800 VDR Monitor”.

JCY-1800

VDR Monitor

・Click [Yes] button.

・Since some files remain in the installation folder after completing the uninstallation, open My
Computer and delete the folder.

Installation folder: C:\Program files\JRC\JCY1800\VDR_Monitor

Playback Software / Real Time Monitor Instruction Manual

22
 Chapter3 Setup for Playback software

Chapter3 Setup for Playback software

Setup is necessary before playing back the VDR/S-VDR data recorded on the CF card.

If setup is not completion, the Playback software does not work.

And in order to play back recorded data of CF card, it is necessary to create a playback folder in the

computer of use advance, and to copy the data.

Shows the flow from setup to playback below.

① Create a playback folder in certain location before Setup. ⇒Refer to 3.1

② Set required information for playback with the Setup software. ⇒Refer to 3.2

③ Start the Playback software, and copy a recorded data of CF card. ⇒Refer to 4.1 and 4.5

3.1 Create a playback folder

(1) To create a playback folder, start My Computer.

(2) Create a folder as follows.

Playback data is copied to the folder made here.

C:\MV JRC

E.g. Ship name

3.2 Set required information for playback with the Setup software
(1) Click the JCY-1800 VDR Monitor icon on the desktop.

The icon is created automatically after installation.

(2) To start up the Setup software, click [SETUP] button.

[SETUP] button

Playback Software / Real Time Monitor Instruction Manual

23
Chapter3 Setup for Playback software

(3) The “Log in” screen displays, and click [OK] button after confirming that “User” is selected in

“Operator” block.

User

(4) The “Setup for User” screen displays.

Playback Software / Real Time Monitor Instruction Manual

24
 Chapter3 Setup for Playback software

(5) Eject a CF card from VDR/S-VDR, and insert it into CF card slot on your PC.

Click [Import] button and select the following file in the CF card in order to import VDR

configuration information (SysInfo.dat). CF card drive differs depending on your PC.

[Import] button

＊: \Init\SysInfo.dat

CF card drive

Caution When a CF card is ejected from the VDR/S-VDR, be sure to follow the

operation of “7.1 How to eject CF card from VDR/S-VDR”.

The CF card may be damaged and record may not be available.

Note If the [Import] button is clicked and a SysInfo.dat file is not imported, the
[Set] button do not become valid.

(6) Check quantity of engine, rudder, thruster and propeller and others which were imported by

VDR/S-VDR configuration data, which were registered when VDR/S-VDR was installed.

Quantity

Playback Software / Real Time Monitor Instruction Manual

25
Chapter3 Setup for Playback software

(7) Click Folder Selection button, and select the folder created at Section 3.1.

Folder Selection button

(8) Click [Set] button, and setup is completed.

To close the Setup software, click [Close] button.

Playback Software / Real Time Monitor Instruction Manual

26
 Chapter3 Setup for Playback software

(9) When setup is completed, the playback folder created at Section 3.1 is formatted as the

following folder structure.

Playback Folder（e.g. C:\JRC_VDR_Data）

Playlist1： Playlist1

for Real Time Monitor

VDR Init

Log

Audio

Visual

Playlist2

VDR Init
Playlist2～10：
Log
For Copying from CF Card
Audio

Visual

Playlist10

Playback Software / Real Time Monitor Instruction Manual

27
Chapter3 Setup for Playback software

Blank Page

Playback Software / Real Time Monitor Instruction Manual

28
 Chapter4 Operation

Chapter4 Operation
4.1 How to start up Playback software
(1) Click the JCY-1800 VDR Monitor icon on the desktop.

(2) Click [MONITOR] button on the Launcher menu.

[MONITOR] button

(3) Playback screen is indicated.

Playback Software / Real Time Monitor Instruction Manual

29
Chapter4 Operation

4.2 How to exit Playback software

(1) Click [Setup] button of bottom right in the playback screen and the Setup screen is indicated.

[Setup] button

(2) Click [Exit] button of bottom left in the Setup screen.

[Exit] button

(3) Click [OK] button in the Confirm window.

(4) The Playback screen is closed and it returns to the Launcher menu.

Playback Software / Real Time Monitor Instruction Manual

30
 Chapter4 Operation

4.3 Playback screen

The Playback screen is composed with Main Block, Status Block, Playback Operation Panel and

Menu Block.

Main Block

Status Block Playback Operation Panel Menu Block

Playback Software / Real Time Monitor Instruction Manual

31
Chapter4 Operation

The Playback screen has Voyage screen, Alarm/Status screen, AIS screen and Radar screen on the

Main Block, and their screens are selected with buttons of the Menu Block.

AIS screen does not display when AIS is not connected to VDR/S-VDR.

Voyage

Alarm/Status

Menu Block

AIS

Radar

Playback Software / Real Time Monitor Instruction Manual

32
 Chapter4 Operation

4.4 Playback Operation Panel

Shows the function of buttons and sections.

① ⑩

③ ⑪

④ ⑫

⑤ ⑬

No. Name Function

① OLDEST time Show the oldest time of the recorded data.

② LATEST time Show the latest time of the recorded data.

③ Slide bar Available to playback from a certain time by sliding the knob.

④ Playback time Shows a playback time.

⑤ Clock button Available to select a playback time from the calendar.

⑥ Playback button Available to start playback.

⑦ Stop button Available to stop playback.

⑧ Rewind button Available to reverse a playback time fast.

⑨ Forward button Available to forward a playback time fast.

⑩ Playlist button Available to playback after selecting a voyage data registered in the playlist.

⑪ Speaker button Available to select audio source and adjust volume.

⑫ Playback Speed Available to select a playback speed from “×1”, ”×2” and “×4”.

Note) Audio is not outputted at playback of ×2 and ×4.

⑬ Slide bar select Available to select time span of slide bar for playback time.

button

Playback Software / Real Time Monitor Instruction Manual

33
 Chapter4 Operation

4.5 To play back CF card data

In order to play back, it is necessary to copy the data of a CF card after the playlist 2.

Shows how to copy below.

(1) Eject a CF Card from VDR/S-VDR, and insert it in the CF card slot.

Caution When a CF card is ejected from the VDR/S-VDR, please be sure to follow

the operation of “7.1 How to eject CF card from VDR/S-VDR”.

The CF card may be damaged and record may not be available.

(2) Click Playlist button. Playlist button

(3) Confirm the CF Card drive is set in the Copy source.

If the drive is not set, please click Folder Select button and select the drive.

(4) Select copy size from 1 hour to 12 hours or All in the Size selection.

If 1hour is selected, 1 hour data from the latest is copied.

(5) Select a playlist in the Copy place box, and click [Copy] button.

Seize selection

Copy source Copy place

Folder Select button [Copy] button

Playback Software / Real Time Monitor Instruction Manual

34
 Chapter4 Operation

Since the comment dialog appears, and enter some comments if required.
Note The entered comments are indicated in the Comment field.

Click [OK] button, and then the copy starts.

It takes time to copy all data (In case of copying the “All”) for 15 minutes.

Playback Software / Real Time Monitor Instruction Manual

35
Chapter4 Operation

Caution If the CF card is continued to eject more than 10minutes,

“MEDIA ERROR” occurs in the VDR/S-VDR.

Please press [ACK] button in the VDR/S-VDR to stop the alarm.

The alarm is canceled automatically when the CF card is inserted in the

VDR/S-VDR.

(6) Select radio button of the playlist copied CF card data, and click [OK] button.

Playlist

radio

button

(7) The setup is completed above, and it is possible to play back with [Playback] button.

Caution When data copying is finished, please be sure to insert a CF card to the

VDR/S-VDR.

If the CF card is continued to eject more than 10 minutes, “MEDIA

ERROR” occurs in the VDR/S-VDR.

Playback Software / Real Time Monitor Instruction Manual

36
 Chapter4 Operation

4.6 To start playback, and to stop

To start playback, click [Playback] button. And to stop playback, click [Stop] button.

Stop

Playback
4.7 To set playback time
Explain how to set playback time.

4.7.1 Setting playback time by Slide bar

If knob is slid, a playback time is forwarded or reversed according to the position.

And time span of Slide bar for playback time can be selected with Slide bar select button.

Slide bar select button

Slide bar

Playback time

Slide bar

If recorded data for some days is played back, time span becomes long.
Note Playback time span of the Slide bar becomes long, and so it is not easy to

adjust playback time.

In that case, select the 12 hours in the Slide bar select button.

Playback time span becomes 12 hours; moreover, scale in every hour is

displayed.
So it is easy to adjust playback time.

Playback Software / Real Time Monitor Instruction Manual

37
Chapter4 Operation

4.7.2 Setting playback time by [Forward] button or [Rewind] button

If [Forward] button is pressed, a playback time is forwarded. And the step time is increased

by pressing the button continuously.

If [Rewind] button is pressed, a playback time is reversed. And step time is increased by

pressing the button continuously.

Forward button
Rewind button

Playback time

4.7.3 Setting playback time by [Clock] button

(1) Select a date you want to play back from calendar.

(A light green part shows that there is recorded data.)

(2) To select time, slide the knob of the Slide bar.

(3) Click [OK] button.

[Oldest Skip] button [Latest Skip] button

Slide bar

If [Oldest Skip] button is clicked, playback time can be skipped to oldest

Note time.

And if [Latest Skip] button is clicked, playback time can be skipped to

latest time.

Playback Software / Real Time Monitor Instruction Manual

38
 Chapter4 Operation

(4) Selected date is indicated in the Playback time

Slide bar select button

Playback time

(5) Click [Playback] button.

(If playback is in progress, playback is restarted automatically without clicking

[Playback] button.)

If 12 hours of slide bar select button is set, time span is 12 hours after
Note selected playback time.
So it becomes easy to select playback time with slide bar.

4.8 To change a playback speed

To change a playback speed, select it from the Playback speed.

“×1” is selected as default, the playback speed is normal.

If “×2” is selected, the playback speed become 2 times faster than normal.

Moreover if “×4” is selected, the playback speed become 4 times faster than normal.

Audio data cannot be played back at "X2" or "X4" speed.

Playback speed

Playback Software / Real Time Monitor Instruction Manual

39
Chapter4 Operation

4.9 To adjust Volume and select audio source

If [Speaker] button is clicked, the Volume control screen appears.

Speaker

To adjust volume, slide up or down the volume knob.

If exclude an unnecessary audio source, click the source and remove the “✓” mark.

Moreover if the All mute is clicked and enter the “✓” mark, all sources are muted.

Audio Source

Volume

All Mute

If audio is not outputted in playback, please confirm audio volume level

Note and mute selection in the Sound and Audio Device Properties which is
opened from the Control Panel of PC.

Playback Software / Real Time Monitor Instruction Manual

40
 Chapter4 Operation

4.10 Voyage screen

There are the Graphic screen and the Numeric screen in the Voyage screen.

To change the screens, click [Voyage] button in the Menu block.

Graphic screen

Numeric screen

Voyage

Playback Software / Real Time Monitor Instruction Manual

41
Chapter4 Operation

4.10.1 Graphic screen

The following explains Graphic screen.

“*” mark displays when data in numeric indication are not recorded.

“N.C” displays when the input equipment is not connected.

Moreover, it becomes an invalid indication when all the items in the divided block have not

been connected.

Invalid

indication

4.10.1.1 Wind block

This block shows wind speed and wind direction by numeric and graphic.

Moreover, if [True/Relative] button is clicked, it changes to true indication (top is the

north) or relative indication (top is head of a ship).

Since VDR/S-VDR usually records only data of relative value, only relative value

displays.

[True/Relative] button

Playback Software / Real Time Monitor Instruction Manual

42
 Chapter4 Operation

4.10.1.2 Rudder direction and heading block

This block shows heading against rudder direction by graphic.

The following figure is an example in case there is one rudder.

The green line shows rudder.

And the blue line shows heading by Gyro.

Rudder direction

Heading

4.10.1.3 Heading block

This block shows heading graphically and numerically by Gyro.

Playback Software / Real Time Monitor Instruction Manual

43
Chapter4 Operation

4.10.1.4 Ship block (Voyage screen)

This block shows status of propeller, rudder and speed by numeric and graphic under

voyage.

The following figure is an example in case there are 1 propeller and 1 rudder.

If [Voyage/Docking] button is clicked, the Ship block is switched to the Docking screen.

Refer to “4.10.1.5 Ship block (Docking screen)” about the Docking screen.

Voyage screen

[Voyage/Docking] button

Playback Software / Real Time Monitor Instruction Manual

44
 Chapter4 Operation

4.10.1.5 Ship block (Docking screen)

This block shows status of propeller, rudder, speed and thruster by numeric and graphic

under docking.

The following figure is an example in case there are 1 propeller, 1 rudders and 1 thruster.

If [Voyage/Docking] button is clicked, the Ship block is switched to the Voyage screen.

Refer to “4.10.1.4 Ship block (Voyage screen)” about the Voyage screen.

Docking screen

[Voyage/Docking] button

Playback Software / Real Time Monitor Instruction Manual

45
Chapter4 Operation

4.10.1.6 Voyage Info block

This block shows date, time, own ship’s position etc. by numeric.

Playback Software / Real Time Monitor Instruction Manual

46
 Chapter4 Operation

4.10.1.7 Depth block

This block shows Depth by numeric and graphic.

The brown zone is seabed, and the light-blue zone is underwater.

A horizontal axis shows lapsed time and shows the depth of water of the newest at right

end.

Underwater

Seabed

4.10.1.8 Engine Telegraph block

This block shows engine telegraph status by graphic.

Telegraph Position

Sub-Telegraph Position

Operating Location

Controlled engine or shaft

Playback Software / Real Time Monitor Instruction Manual

47
Chapter4 Operation

4.10.2 Numeric screen

In numeric screen, all data of graphic screen are showed in numeric.

“*“ mark displays if data in numeric indication have not yet received or illegal data are

inputted,

“N.C” displays when the input equipment is not connected.

Playback Software / Real Time Monitor Instruction Manual

48
 Chapter4 Operation

4.11 Alarm/Status screen

The Alarm/Status screen shows alarm information, status of engine telegraph, door status, water

level and fire detection etc.

This screen is composed 3 blocks of Alarm/Status, Category Menu and Alarm/Status Menu.

To show door status e.g., click [Door] button from the Alarm/Status Menu.

Moreover, to show about Steering gear e.g., click the Steering gear from the Category Menu.

And if [Section] button is clicked, the Alarm/Status information is sorted.

Alarm/Status

Category
Menu

Alarm/Status
Menu

Section button

Playback Software / Real Time Monitor Instruction Manual

49
Chapter4 Operation

4.12 Radar screen

It is possible to view a Radar image captured every 15 seconds in this screen.

It is prepared so that the icon and the menubar may effectively view the radar screens.
If Radar Interfaces (Option Unit) are added, it is possible to view maximum 4 images.

Playback Software / Real Time Monitor Instruction Manual

50
 Chapter4 Operation

4.12.1 Icon

Shows the function of buttons below.

① ④

② ⑤

③ ⑥

No. Name Function

① Zoom Out Available to contract a selected radar screen.

② Zoom In Available to expand a selected radar screen.

③ Tile Available to arrange radar screens like tiles.

④ Close Available to close the radar screen.

⑤ Print Available to print a selected radar screen.

⑥ Cascade Available to arrange radar screens in forward and backward.

4.12.2 Menu bar

Shows the composition of the menu bar below.

The functions are same as icons of “4.12.1 Icon”.

File Window
Zoom Out Tile
Zoom In Cascade
Print
Close

Playback Software / Real Time Monitor Instruction Manual

51
Chapter4 Operation

4.13 AIS Screen

There are the Graphic screen and List screen in the AIS screen.

To select the screens, click [Graphic] button or [List] button.

And simple information of own ship and AIS targets is indicated on right side.

Graphic screen

Simple
Information

List Screen

Graphic / List

Graphic/
List button

Playback Software / Real Time Monitor Instruction Manual

52
 Chapter4 Operation

4.13.1 Graphic screen

Centering on own ship, the state of AIS target is indicated on graphics by a symbol.

Screen area is expanded or contracted by the Range button. (Radius: from 0.75 to 24

nm)

Range button

Playback Software / Real Time Monitor Instruction Manual

53
Chapter4 Operation

Explains about symbols in the following table.

Category Symbol Explain

Own ship ・Solid line shows heading.

・ Dashed line shows COG(Course Over

Ground).

AIS Target ・Solid line shows heading.

・ Dashed line shows COG(Course Over

Ground).

If position report of a ship is not received more

than a certain time, the symbol is indicated.

AIS

Base Station

Aids-to

-navigation

Mouse

cursor

Playback Software / Real Time Monitor Instruction Manual

54
 Chapter4 Operation

4.13.2 List screen

Position report, ship's name, IMO number, call sign and length of hull etc are showed in

this screen.

It is indicated on near order from a top from own ship.

Playback Software / Real Time Monitor Instruction Manual

55
Chapter4 Operation

4.13.3 Detail Information of own ship

If [Detail] button in the simple information block, the detail screen is indicated.

Playback Software / Real Time Monitor Instruction Manual

56
 Chapter4 Operation

4.13.4 Detail information of AIS target

If [Detail] button in the simple information block, the detail screen is indicated.

Playback Software / Real Time Monitor Instruction Manual

57
Chapter4 Operation

4.14 To confirm the record sentences in the NMEA format

Available to confirm the record sentences in the NMEA format on the Dump screen.

To open the Dump screen, operate as follows.

(1) Click [Setup] button in the Menu Block.

[Setup] button

(2) Select the Maintenance tab in the setup and click [View] button.

Maintenance tab

[View] button

Playback Software / Real Time Monitor Instruction Manual

58
 Chapter4 Operation

(3) Select a port No. in the combo box and click

To view the record NMEA sentences, click [Start] button.

To abort view, click [Stop] button.

Shows the function of buttons below.

②
①

No. Name Function

① Port No. Available to select a certain channel or all channels.

② Start Available to start view.

③ Clear Available to clear NMEA sentences on the Dump screen.

④ Stop Available to abort view.

⑤ Dump screen NMEA sentence is shown on the screen.

⑥ Close Available to close the Dump screen.

Playback Software / Real Time Monitor Instruction Manual

59
Chapter4 Operation

4.15 To print screen

To print screen, click [Print] button in the MENU Block.

[Print] button

Note To print, it is necessary to install a printer driver in a used PC beforehand.

Playback Software / Real Time Monitor Instruction Manual

60
 Chapter4 Operation

4.16 To confirm the VDR/S-VDR system information

Available to confirm the VDR/S-VDR system configuration that is required in the International

Standard on the VDR/S-VDR System Information screen.

To open the VDR/S-VDR System Information screen, operate as follows.

(1) Click [Setup] button in the Menu Block and select the Version tab.

[Setup] button

(2) Click [View Info] button.

[View Info] button

Playback Software / Real Time Monitor Instruction Manual

61
Chapter4 Operation

(3) The VDR/S-VDR System Information screen is opened.

Shows the function of buttons below.

No. Name Function

① RCU Available to show the RCU system information on the screen.

② Close Available to close the screen.

Playback Software / Real Time Monitor Instruction Manual

62
 Chapter4 Operation

4.17 How to customize screen layout

It is possible to move, expand and reduce the Voyag1 and Voyage2 screens.

And when [Setup] button is clicked, setting tabs of each block are indicated, and if a check mark of

"Dialog" is removed, the corresponding block disappears. Therefore it is possible to indicate

necessary blocks only.

When Dialogs are changed on the Voyage1 screen, a layout of the Voyage1 screen is changed.

If the Voyage2 screen is changed, please change Dialogs on the Voyage2 screen.

The screen layouts are saved automatically at exiting the Playback software.

Course Tab e.g.)

Dialog

[Exit] button

(1/4)

Tab Corresponding Block Note

Course Bar

Climate － Not used

Ship (Voyage)

Playback Software / Real Time Monitor Instruction Manual

63
Chapter4 Operation

(2/4)

Tab Corresponding Block Note

Ship (Docking)

Radar ・Initially this block is shown on the

Voyage2 screen only.

Current / Wind

Voyage Info

Playback Software / Real Time Monitor Instruction Manual

64
 Chapter4 Operation

(3/4)

Tab Corresponding Block Note

Depth Graph ･It is possible to change a graph range

in addition to selection of visible and

invisible.

･It is possible to select “KELL” mode or

“WATER/TRANS/KEEL” mode.

Engine Graph ･ Initially this block is not shown. If

needed, change the dialog.

･It is possible to change a graph range

in addition to selection of visible and

invisible.

Heading / ･It is possible to change a graph range

Rudder in addition to selection of visible and

invisible.

･ Initially this block is shown on the

Voyage1 screen only.

Engine

Telegraph

Time － ･There is no corresponding block, but

Correction shows how to correct time.

Playback Software / Real Time Monitor Instruction Manual

65
Chapter4 Operation

(4/4)

Tab Corresponding Block Note

AIS ・It is possible to change AIS target

number and range in the AIS screen.

System ・It is possible to select blue or black for

background color.

Playback Software / Real Time Monitor Instruction Manual

66
 Chapter4 Operation

4.18 How to restore to initial screen layout

It is possible to restore to initial screen layout by [Restore] button in the Maintenance tab.

If the Voyage1 screen is restored, click [Restore] button after opening the Voyage1 screen.

If the Voyage2 screen is restored, click [Restore] button on the Voyage2 screen.

[Save] button ※

[Restore] button

[Reread] button ※

※ [Save] and [Reread] buttons are used by a service person.

Those operations are omitted in this manual.

Playback Software / Real Time Monitor Instruction Manual

67
Chapter4 Operation

4.19 Optional Function

As an optional function, by making LAN connection with VDR/S-VDR, a real time indication and

record for a long time are available as Real Time Monitor. Shows the operation below.

Note Standard function of the Playback software is playback only.

If you require the real time indication and record for a long time, contact

the Sales Department of Japan Radio Company, nearest branch

company, branch office, sales office, or our agent

4.19.1 Real Time Indication

(1) Confirm that the “Live” of the Status block goes out.

When "Live" is lighting up yellow, it is already becoming a real-time indication, so that it is

unnecessary to operate as follows.

(2) Click the [Live/Play] button in the Menu block.

(3) The Confirmation screen of indication clear. If it is good, click [OK] button.

(4) The "Live" lights up yellow, and it changes to real time indication.

Note It is possible to change to playback indication with [Live/Play] button. In

case of playback, the “Play” of the Status block lights up green.

Playback Software / Real Time Monitor Instruction Manual

68
 Chapter4 Operation

4.19.2 Record for a Long Time

The capacity of HDD required in order to record for a long time changes with a record period

and contents of record.

Please purchase a HDD after asking our company the capacity.

In that case, purchase external HDD of the USB version 2.0.

4.19.2.1 Record Setup

It is necessary to set a record folder or a record period, before starting record.

Starts the Setup software from the Launcher menu to set them.

(1) Click [SETUP] button on the Launcher menu.

[SETUP] button

(2) Click [Folder Selection] button in the Setup Folder, and select a record folder.

Before select the record folder, please create the folder with the My Computer.

To create the playback folder, refer to the “3.1 Create a playback folder”.

Folder Selection button

Playback Software / Real Time Monitor Instruction Manual

69
Chapter4 Operation

(3) Set a record period in the Record block

About Overwrite)

When there is the check in the Overwrite and a record period is exceeded, oldest data is

overwritten by newest data.

(4) Click the [Set] button.

When the setup is completed, the “Setup OK” screen is indicated.

(5) To close the Setup software, click [Close] button.

The record setup is completed.

Playback Software / Real Time Monitor Instruction Manual

70
 Chapter4 Operation

4.19.2.2 Record Start

(1) Click [Backup] button in the Menu block.

(2) Since a record folder and free space of a HDD are indicated, and click [REC] button after

check.

(3) The “REC” in the Status block lights up red, and record is started.

The record by the Real Time Monitor records data which the
Note VDR/S-VDR outputs by a UDP protocol.

On an UDP protocol, data is effluence. Even if it misses data, data are

not resent. There may be no data in recorded data at that time.

Therefore, lack may arise in recorded data.

Playback Software / Real Time Monitor Instruction Manual

71
Chapter4 Operation

4.19.2.3 Record Stop or Pause

(1) Click [Backup] button in the Menu block.

(2) When record is stopped, click [STOP] button. When record is paused, click [PAUSE] button.

(3) The “REC” in the Status block goes out, and the record is stopped or paused.

Playback Software / Real Time Monitor Instruction Manual

72
 Chapter4 Operation

4.19.2.4 To playback recorded data

The recorded data by the Real Time Monitor are saved in the Playlist1.

To play back the recorded data, select the Playlist1 in accordance with the following

operation.

(1) Click [Play List] button.

Playlist button

When a LAN cable of the Real Time Monitor is disconnected for playing
Note back in another sitting room, the playback is not possible.

In that case, Exit the Real Time Monitor once.

Start the Setup software, and press [Disconnect] button in the Ethernet

tab. Then restart the Real Time Monitor, and it is possible to play back.

When the LAN cable is connected again, press [Connect] button with the

same operation.

Playback Software / Real Time Monitor Instruction Manual

73
Chapter4 Operation

(2) Select the Playlist1, and click [OK] button.

Record Place
Note

Playback Folder（e.g. C:\JRC_VDR_Data）

Record to here

Playlist1： Playlist1

for Real Time

Monitor VDR Init

Log

Audio

Visual

Playlist2

Playlist2～10：

For Copying from CF Card

Playlist10

Playback Software / Real Time Monitor Instruction Manual

74
 Chapter5 Converting Recorded Data into Industry Standard Formats

Chapter5 Converting Recorded Data into Industry Standard Formats

5.1 Starting conversion software

(1) Click [CONVERT] button, so that conversion software starts up.

[CONVERT] button

(2) Conversion software screen displays.

(3) Method for conversion

Refer to Section 5.2, when converting all recorded data.

Refer to Section 5.3, when partially converting recorded data

Playback Software / Real Time Monitor Instruction Manual

75
Chapter5 Converting Recorded Data into Industry Standard Formats

5.2 Convert all recorded data

(1) Click Folder Selection button in Source Folder, and select “VDR” folder in the folder that

recorded data are saved.

[Folder Selection]

button

Select the “*\Playlist2\VDR”.

Folder Selection

Note
Playback Folder (e.g. C:\JRC_VDR_Data） Select here
Playlist1

VDR
Init

Log

Audio

Visual

Playlist2

VDR

Init

Log

Audio

Visual

Playlist10

Playback Software / Real Time Monitor Instruction Manual

76
 Chapter5 Converting Recorded Data into Industry Standard Formats

(2) Create any folder for saving converted files on desktop.

Here, "Convert_Data" folder was created as an example.

(3) Click Folder Selection button in “Convert Folder”, and select “Convert_Data” folder as the

destination of converted files.

Folder Selection

button

Select the “\Convert_Data” on desktop.

Playback Software / Real Time Monitor Instruction Manual

77
Chapter5 Converting Recorded Data into Industry Standard Formats

(4) Click [Convert].

W hen conversion starts, progress of conversion is indicated in progress bar.

Also, converted files are indicated in list box.

[Convert] button

(5) Stop converting

Click [Cancel] button in order to stop converting.

Playback Software / Real Time Monitor Instruction Manual

78
 Chapter5 Converting Recorded Data into Industry Standard Formats

5.3 Converting a part of recorded data

(1) Click Folder Selection button in “Convert Folder”, and select “Convert_Data” folder as the

destination of converted files.

Folder Selection button

(2) Drag and drop a part of recorded data into list box.

Recorded data that can be partially converted are single file, two or more files, single folder, or

two or more folders.

When a folder is selected, all files in the folder are converted.

* Refer to next page for the example operation.

Note For Windows Vista, conversion operation by drag and drop is not

available.

(3) Conversion starts automatically.

W hen conversion starts, the progress of conversion is indicated in progress bar.

Also, converted files are indicated in list box.

Playback Software / Real Time Monitor Instruction Manual

79
Chapter5 Converting Recorded Data into Industry Standard Formats

Drag & Drop

Note For Windows Vista, conversion operation by drag and drop is not

available.

Playback Software / Real Time Monitor Instruction Manual

80
 Chapter5 Converting Recorded Data into Industry Standard Formats

5.4 Converted files (Industry Standard Formats Files)

The conversion software creates converted files as follows.

Data File Name Note

Configuration YYMMDD,hhmmss,CF,????????.csv
Information

Digital Sensor Data YYMMDD,hhmmss,DD,????????.txt

Audio YYMMDD,hhmmss,M1,????????.wav Mix MIC-CH1, CH2 and CH3

YYMMDD,hhmmss,M2,????????.wav Mix MIC-CH4, CH5 and CH6

YYMMDD,hhmmss,M3,????????.wav Mix MIC-CH7, CH8 and CH9

YYMMDD,hhmmss,V1,????????.wav Mix VHF-CH1, Ch2 andCH3

Radar Display Video YYMMDD,hhmmss,R1,????????.png Main Radar

YYMMDD,hhmmss,R2,????????.png Sub Radar

YYMMDD: Date

hhmmss: Time (UTC)

????????: IMO No. (If IMO number is not entered, automatically converts to “99999999”.)

Playback Software / Real Time Monitor Instruction Manual

81
Chapter5 Converting Recorded Data into Industry Standard Formats

Blank Page

Playback Software / Real Time Monitor Instruction Manual

82
 Chapter6 Trouble Shooting

Chapter6 Trouble Shooting

If the Real Time Monitor may be not normal or occur a error, please confirm the contents of this chapter

before contact us

No. Symptom Cause Action

1 The real time indication is not Faulty wiring of a LAN cable Check the connections.

possible. The power of the VDR/S-VDR Turn on the power of the VDR

Interface is not turned on. Interface.

2 The image indication is not The Power of a captured Turn on power of a captured

possible. display is not turned on. display.

3 There are no audio outputs of Audio monitoring is not On private, the monitoring may

the real time. validated. be prevented.

To monitor, The setup by our

serviceman is necessary.

Please contact us in that case.

Audio volume of the Playback Adjust the Volume or invalidate

software is low. the Mute.

Or mute is validated.

Audio volume of the Windows Adjust the Volume or invalidate

or is low. the Mute in the “Volume Control”

Or mute is validated. and “Wave”.

4 The record is not possible. Faulty wiring of the external Check the connections.

HDD

The power of the external Turn on the power of the

HDD power is not turned on. external HDD.

5 The audio recording is not The audio recording is not To record, the setup by our

possible. necessary. serviceman is necessary.

Please contact us in that case.

6 The image recording is not The image recording is not as To record, the setup by our

possible set necessity. serviceman is necessary.

Please contact us in that case.

Playback Software / Real Time Monitor Instruction Manual

83
Chapter6 Trouble Shooting

No. Symptom Cause Action

7 Record data are less than a The free space of the HDD is Increase a free space by

record period. not enough for the record deleting unnecessary data, or

period. exchange to a mass HDD

8 When a LAN cable of the Real The [Connect] button is In order to operate under

Time Monitor is disconnected, pressed and operation is in the disconnecting the LAN, please

the playback is not possible. state of LAN connection. press the [Disconnect] button

in the Setup software.

Refer to 4.19.2.4.

Playback Software / Real Time Monitor Instruction Manual

84
 Chapter7 Appendix

Chapter7 Appendix
7.1 How to eject CF card from VDR/S-VDR
Open the door with key.

Key

Internal Operation
Panel

Playback Software / Real Time Monitor Instruction Manual

85
Chapter7 Appendix

Please operate Internal Operation Panel as follows.

(1) Push [CARD STOP] button.

(2) The CARD LED blinks for 5sec and goes out. Then ejection of CF card becomes possible.

(3) Push [EJECT] button, and eject a CF card.

When 10 minutes pass after ejecting CF card, “Error31” will be indicated on Operation Panel and

alarm buzzer will sound.

Push [ACK] button to stop the alarm. Error will be canceled if CF card is re-inserted.

CF CARD SLOT [ACK] button

EJECT button

ＨＥＡＤＩＮＧ

CARD LED（Green） ＰＯＷＥＲ

ＡＬＡＲＭ ＤＥＴＡＩＬ

ＭＯＤＥ
ＲＥＣＯＲＤＩＮＧ
ＳＹＳＴＥＭ ＣＯＤＥ
ＡＬＡＲＭ

ＡＣＫ ＤＩＭ

ＥＮＴ

MEDIA LED（Red） ＮＣＧ－１６９ ＶＤＲ ＯＰＥＲＡＴＩＯＮ ＰＡＮＥＬ

[CARD STOP] Operation Panel Unit

button

Internal Operation Panel

Caution When data copying is finished, please be sure to insert a CF card to the

VDR/S-VDR.

If the CF card is continued to eject more than 10 minutes, “MEDIA

ERROR” occurs in the VDR/S-VDR.

Caution When a CF card is inserted to the VDR/S-VDR, the CF CARD LED

lights up and record into the CF card is restarted.

If the LED does not light up, the CF card may be faulty.
Please contact us in that case.

Playback Software / Real Time Monitor Instruction Manual

86
 Chapter7 Appendix

7.2 Sentence and indication place

(1/4)

Screen Block Section Data

Indication Unit Sentence

Voyage1 Wind True Wind Direction xxx.x deg(°) $xxMWV

Voyage2 Wind Speed xx.x kt, m/s

（Graphic） Relative Wind Direction xxx.x deg(°)

Wind Speed xx.x kt, m/s

Rudder direction Rudder Starboard xxx.x deg(°) $xxRSA

and heading Port xxx.x deg(°)

Heading True xxx.x deg(°) $xxHDT

Heading True xxx.x deg(°) $xxHDT

Ship (Voyage) STW (Water-reference) [AS/AH]xx.x kt $xxVBW

SOG (Ground-reference) xx.x kt

Propeller Pitch Starboard xxx.x deg(°) $xxRPM

Port xxx.x deg(°)

Revolution Starboard xx min-1 $xxRPM

Port xx min-1

Rudder Starboard xxx.x deg(°) $xxRSA

Port xxx.x deg(°)

Ship (Docking) Speed Bow (The left and right in bow) [P/S]xx.x kt $xxVBW

SOG (Ground-reference) [AS/AH]xx.x kt

Stern (The left and right in stern) [P/S]xx.x kt

Thruster Pitch xxx.x deg(°) $xxTRD

Revolution xxx.x min-1

Propeller Pitch Starboard xxx.x deg(°) $xxRPM

Port xxx.x deg(°)

Revolution Starboard xx min-1 $xxRPM

Port xx min-1

Rudder Starboard xxx.x deg(°) $xxRSA

Port xxx.x deg(°)

Playback Software / Real Time Monitor Instruction Manual

87
 Chapter7 Appendix

(2/4)

Screen Block Section Data

Indication Unit Sentence

Voyage1 Engine Telegraph Position STOP ENGINE e.g. --- $xxETL

Voyage2 Telegraph SUB Telegraph S/B, F/A, F/E e.g. ---

(Graphic) Ope.Location Bridge, Port wing, ---

Starboard wing e.g.

Propeller Cont. Single, Starboard, ---

Wing e.g.

Voyage Info UTC DD/MM/YYYY --- $xxZDA

hh:mm:ss

LMT DD/MM/YYYY ---

hh:mm:ss

Position GPS, DGPS --- $xxGNS

Lat. xx°xx.xxx’[N/S] ---

Lon. xxx°xx.xxx’[E/W] ---

Local Geodetic Datum WGS84,WGS72 e.g. $xxDTM

Steer. Mode Auto/Manual $xxHTD

Override ON/OFF

Depth Depth (Water / Tran. / Keel) xxx.x m $xxDPT

VDR Date and Time UTC DD/MM/YYYY --- $xxZDA

(Numeric) LMT DD/MM/YYYY ---

Ship’s Position Position GPS, DGPS --- $xxGNS

Lat. xx°xx.xxx’[N/S] ---

Lon. xxx°xx.xxx’[E/W] ---

Datum WGS84,WGS72 e.g. $xxDTM

Wind speed True Speed xxx.x m/s $xxMWV

and Direction Direction xx.x deg(°)

Relative Speed xxx.x m/s

Direction xx.x deg(°)

Playback Software / Real Time Monitor Instruction Manual

88
 Chapter7 Appendix

(3/4)

Screen Block Section Data

Indication Unit Sentence

VDR Depth Offset from transducer Depth(Water/Tran./ --- $xxDPT

(Numeric) Keel)

Depth xxx.x m

Heading True xxx.x deg(°) $xxHDT

Speed Water STW (Water-reference) [AS/AH]xx.x kt $xxVBW

and Ground SOG (Ground-reference) [AS/AH]xx.x kt

Bow (The left and right in bow) [P/S]xx.x kt

Stern (The left and right in stern) [P/S]xx.x kt

Rudder order Control/ Port xxx.x deg(°) $xxHTC

and response Order Starboard xxx.x deg(°)

Order/ Port xxx.x deg(°) $xxHTD

Response Starboard xxx.x deg(°)

Response Port xxx.x deg(°) $xxRSA

Feedback Starboard xxx.x deg(°)

Heading/Track Steering mode Manual Steering --- $xxHTD

control /Stand alone

/Heading Control

/Track Control

/Rudder Control

Override ON/OFF ---

Heading-to-steer xxx deg(°)

Playback Software / Real Time Monitor Instruction Manual

89
 Chapter7 Appendix

(4/4)

Screen Block Section Data

Indication Unit Sentence

VDR Engine order and Remote control Port Revolution xx min-1 $xxPRC

(Numeric) response order

Pitch xxx.x deg(°)

Starboard Revolution xx min-1

Pitch xxx.x deg(°)

Propeller Port Revolution xx min-1 $xxRPM

response Pitch xxx.x deg(°)

Starboard Revolution xx min-1

Pitch xxx.x deg(°)

Thruster control Control/Order Bow Revolution xx min-1 $xxTRC

order and
Pitch xxx.x deg(°)
response
Stern Revolution xx min-1

Pitch xxx.x deg(°)

Response Bow Revolution xx min-1 $xxTRD

Pitch xxx.x deg(°)

Stern Revolution xx min-1

Pitch xxx.x deg(°)

Playback Software / Real Time Monitor Instruction Manual

90
 JCY-1800/1850
VDR/S-VDR

CYC-316A Playback Software /

Real Time Monitor
Instruction Manual
Version 2.0

For further information,contact:

Not use the asbestos

URL http://www.jrc.co.jp
Marine Service Department
Telephone : +81-3-3492-1305
Facsimile : +81-3-3779-1420
e-mail : [email protected]
AMSTERDAM Branch
Telephone : +31-20-658-0750
Facsimile : +31-20-658-0755
e-mail : [email protected]
SEATTLE Branch
Telephone : +1-206-654-5644
Facsimile : +1-206-654-7030
e-mail : [email protected]
CODE No.7ZPJD0378C 01ETM ISO 9001, ISO 14001 Certified
MAY. 2008 Edition 1 JRC Printed in Japan