Application Note

Siemens HiPath 4000 Release 3 using E1 ECMA Q.SIG to Cisco

Unified Communications Manager 6.0

October 26, 2007 Revision 3

Table of Contents
Introduction .............................................................................................................................................................................................................. 1
Network Topology.................................................................................................................................................................................................... 2
Limitations................................................................................................................................................................................................................ 2
B-Channel Mapping: ........................................................................................................................................................................................... 2
Connected Name and Number Restrictions:........................................................................................................................................................ 2
Additional Network Feature Path Replacement for Call Diversion by forward switching: ................................................................................. 2
Overlap Sending .................................................................................................................................................................................................. 2
MWI .................................................................................................................................................................................................................... 2
System Components ................................................................................................................................................................................................. 3
Hardware Requirements ...................................................................................................................................................................................... 3
Software Requirements ....................................................................................................................................................................................... 3
Features .................................................................................................................................................................................................................... 3
Features Supported .............................................................................................................................................................................................. 3
Configuration............................................................................................................................................................................................................ 4
Configuring the Siemens HiPath 4000 PBX........................................................................................................................................................ 4
Configuration Menus and Commands for Hipath 4000....................................................................................................................................... 4
Configuring the Cisco Unified Communication Manager ................................................................................................................................. 25
Configuring the CMM-E1 gateway ................................................................................................................................................................... 78
Acronyms ............................................................................................................................................................................................................... 83

Introduction

• This is an application note for connectivity of Siemens HiPath 4000 Release 3 PBX with Cisco Unified Communications Manager
(CUCM) Release 6.0 via Cisco CMM-E1 as MGCP gateway using ECMA Q.SIG protocol.

• The network topology diagram (Figure 1) shows the test setup for end-to-end interoperability with the Cisco Unified Communications
Manager connected to the PBX via Cisco CMM-E1 link as MGCP gateway.

• Connectivity is achieved by using the PRI QSIG E1 protocol type on the MGCP gateway with Unified Communications Manager
Service parameter Q.SIG variant of ECMA and ECMAV1 switch type on the Hipath 4000 PBX.

• This Application Note uses the Cisco CMM-E1 voice gateway, however other Cisco voice gateways are also an option to use since
Cisco Unified Communications Manager Q.SIG implementation does not depend on the physical interface.

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 1 of 86
EDCS - 607736 Revision 3
Network Topology
Figure 1. Basic Call Setup

Limitations

B-Channel Mapping:
• Siemens HiPath 4000 PBX uses Timeslot channel numbering (1-15 & 17-31) when Q.SIG protocol “ECMA1” is selected, therefore the
Cisco CMM-E1gateway configuration for Channel IE Type field should be set to Timeslot Number.
Connected Name and Number Restrictions:
• Siemens phone displayed dialed digits when CUCM sends Connected Name and Number as restricted.
Additional Network Feature Path Replacement for Call Diversion by forward switching:
• Siemens HiPath 4000 PBX does not send Path Replacement proposal for Call Diversion by forward switching.
Overlap Sending
• When CUCM is configured for Overlap Sending, calls made from SIP Phones C2 or D2 (Fig 1) to Siemens Hipath result in the Name
not being updated on the SIP phone during Alerting State (Siemens has been verified to be sending Alerting Name). This interoperability
issue is considered a limitation on Cisco Unified Communication Manager and an internal corrective action bug fix ticket has been
generated to resolve this issue in future releases. (DDTS # CSCsj51238 Title: SIP Phone fails to display Alerting Name when using
OVERLAP Sending).
MWI
• When Siemens Hipath 4000 is configured for ECMAV1 Q.SIG variant, the APDU sent to activate MWI on any Siemens digital station
from CUCM is rejected by the Siemens Hipath for reasons unknown.

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 2 of 86
System Components

Hardware Requirements

Cisco Hardware:
• Cisco 35xx Ethernet Switch

• Cisco CMM-E1 Gateway

• Cisco IP Phones

• Cisco Unified Communication Manager Server

Siemens Hipath 4000 PBX Hardware:

• DIU-N2

Software Requirements

The following software is required:

• Cisco Unified Communication Manager Release 6.0
• PBX software release 3

• Cisco IOS Release 12.4 (for the CMM gateway)

Features

Features Supported
• CLIP-Calling Line (Number) Identification Presentation

• CLIR-Calling Line (Number) Identification Restriction

• CNIP-Calling Name Identification Presentation

• CNIR-Calling Name Identification Restriction

• COLP-Connected Line (Number) Identification Presentation

• COLR- Connected Line (Number) Identification Restriction - see limitations section

• CONP-Connected Name Identification Presentation

• CONR- Connected Name Identification Restriction - see limitations section

• Sending Alerting Name

• Sending Busy Name

• CT-Call Transfer (by join)

• CFU-Call Forwarding Unconditional (by join)

• CFB-Call Forwarding Busy (by join)

• CFNR-Call Forwarding No Reply (by join)

• CFU-Call Forwarding Unconditional (by Reroute)

• CFB-Call Forwarding Busy (by Reroute)

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 3 of 86
 • CFNR-Call Forwarding No Reply (by Reroute)

• CCBS-Call Completion to Busy Subscriber

• CCNR-Call Completion No Reply

• ANF-PR-Additional Network Feature Path Replacement (for Call Transfer by join)

• ANF-PR-Additional Network Feature Path Replacement (for Call Diversion by forward switching) - see limitations section

• ANF-PR-Additional Network Feature Path Replacement (for Trombone connection)

• MWI- Message Waiting Indication (lamp ON, lamp OFF) 1 - see limitation section

Configuration

Configuring the Siemens HiPath 4000 PBX

1. Add the new access code to Dialing Plans using WABE + LDPLN.

2. Add the new trunk board using BCSU.

3. Configure Class of Trunk using COT.

4. Configure Class of Parameter for device handler using COP.

5. Configure Class of Service using COSSU.

6. Add the new trunk group access code using BUEND.

7. Configure trunk using TDCSU.

8. Configure Reference Clock using REFTA.

9. Configure trunk Least Cost Routing using LDAT + RICHT.

10. Configure LCR Out-dial Rules using LODR.

11. Enable In-Band DTMF signaling for the Digital Stations using SBCSU.

12. Configure Digital Station for MWI application.

13. Configure Message Center’s Service Access Number for MWI application.

14. Configure Digital Station’s Class of Service for Mailbox MWI application.

Configuration Menus and Commands for Hipath 4000

DPLN

<dis-wabe:gen;
DIS-WABE:GEN;
H500: AMO WABE STARTED
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------

1
MWI was tested with Communication Manager 6.0 as the Message Center PINX and PBX users as remote
subscribers.

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 4 of 86
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| 0 |. .**** ..*** **... ..... .*| CO | R |
| 001 - 009 |* ..... ..... ..... ..... ..| NETRTE | |
| 111 |. .**** ***** **... ..... .*| TIE | |
| 12 |. .**** ***** **... ..... .*| TIE | R |
| 13 - 14 |. .**** ***** **... ..... .*| TIE | |
| 21 |. ..... ..... ..... ....* ..| KNOVRKY | |
| 22 |. ..... ..... ..... ....* ..| DNDKY | |
| 222 |. .**** ***** **... ..... .*| TIE | |
| 23 |. ..... ..... ..... ....* ..| FWDKY | |
| 24 |. ..... ..... ..... ....* ..| MBKY | |
| 25 |. ..... ..... ..... ....* ..| MSGRKY | |
| 26 |. ..... ..... ..... ....* ..| DAKY | |
| 27 |. ..... ..... ..... ....* ..| DSSKY | |
| 28 |. ..... ..... ..... ....* ..| VCRKY | |
| 29 |. ..... ..... ..... ....* ..| VCKY | |
| 30 |. ..... ..... ..... ....* ..| CONFKY | |
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| 3000 - 3010 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 30 |
| | | |DNNO 0- 0-222 |
| 3011 - 3020 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 31 |
| | | |DNNO 0- 0- 31 |
| 3021 - 3030 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 32 |
| | | |DNNO 0- 0- 32 |
| 3031 - 3040 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 33 |
| | | |DNNO 0- 0- 33 |
| 3041 - 3050 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 35 |
| | | |DNNO 0- 0- 35 |
| 31 |. ..... ..... ..... ....* ..| NAMEKY | |
| 32 |. ..... ..... ..... ....* ..| PARKKY | |
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| 33 |. ..... ..... ..... ....* ..| CCKY | |
| 34 |. ..... ..... ..... ....* ..| HTKY | |
| 35 |. ..... ..... ..... ....* ..| STKY | |
| 36 |. ..... ..... ..... ....* ..| REMKY | |
| 36 - 37 |. .**** ..*** **... ..... .*| CO | |
| 38 |. ..... ..... ..... ....* ..| TIMEKY | |
| 39 |. .**** ***** **... ..... .*| TIE | |
| 4000 - 4050 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 111 |
| | | |DNNO 0- 0-111 |
| 4051 - 4566 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 222 |
| | | |DNNO 0- 0-222 |
| 4567 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 34 |
| | | |DNNO 0- 0-200 |

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 5 of 86
 ------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| 4568 - 4999 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 222 |
| | | |DNNO 0- 0-222 |
| 5000 - 5040 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 0 |
| | | |DNNO 0- 0-555*|
| 5500 - 5501 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 56 |
| | | |DNNO 0- 0-560 |
| 555 |. .**** ***** **... ..... .*| OWNNODE | |
| 560 |. .**** ***** **... ..... .*| TIE | |
| 59 |. .**** ***** **... ..... .*| TIE | |
| 6000 - 6009 |. .**** ***** **... ..... .*| STN | R |
| | | |DESTNO 0 |
| | | |DNNO 0- 0-555*|
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| 7000 - 7002 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 56 |
| | | |DNNO 0- 0-560 |
| 8000 - 8050 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 222 |
| | | |DNNO 0- 0-222 |
| 8060 |. .**** ***** **... ..... .*| TIE | |
| 8070 |. .**** ***** **... ..... .*| TIE | |
| 83 |. .**** ..*** **... ..... .*| SPDC1 | |
| 84 |. .**** ..*** **... ..... .*| SPDC2 | |
| 88 |. ..... ..*.. ..... ..... .*| SCONSI | R |
| 89 |. ..... ...*. ..... ..... ..| SCONSCO | R |
| 9 |. .**** ***** **... ..... .*| TIE | |
| *13 |. ....* ..... ..... ..... ..| AHTVCE | |
| *15 |. *.... ..**. ..... ..... .*| SPLIT | |
| *16 |. ....* ..... ....* ..... ..| AREM | |
| *17 |. *.... ..**. ..... ..... ..| TRACE | |
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| *18 |. ....* ..... ..... ..... ..| ACOSX | |
| *19 |. *.... ..... ..... ..... ..| KNOVR | |
| *20 |. ....* ..... ..... ..... ..| ADND | |
| *25 |. ....* ..... ..... ..... ..| FWDTERM | |
| *29 |. ....* ..... ....* ..... ..| AFFWDVCE | |
------------------------------------------------------------------------------

AMO-WABE -111 DIALLING PLANS, FEATURE ACCESS CODES

DISPLAY COMPLETED;

Enbloc Sending Dial Plan, DPLN

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 6 of 86
<DISPLAY-LDPLN:TYPE=LDP,LDPNO=4;
DISPLAY-LDPLN:TYPE=LDP,LDPNO=4;
H500: AMO LDPLN STARTED
+--------------+-------------------------------------------------+
| | |
| LDPNO : 4 | LDP : 111-X |
| | SPC : 22 |
| | FDSFIELD : 0 SDSFIELD : 0 PINDP : N |
+------+-------+-------------------------------------------------+
| DPLN | LROUTE| LAUTH |
|------+-------+-------------------------------------------------+
| 0 | 1 | 1 |
| 1 | 1 | 1 |
| 2 | 1 | 1 |
| 3 | 1 | 1 |
| 4 | 1 | 1 |
| 5 | 1 | 1 |
| 6 | 1 | 1 |
| 7 | 1 | 1 |
| 8 | 1 | 1 |
| 9 | 1 | 1 |
| 10 | 1 | 1 |
| 11 | 1 | 1 |
| 12 | 1 | 1 |
| 13 | 1 | 1 |
| 14 | 1 | 1 |
| 15 | 1 | 1 |
+------+-------+-------------------------------------------------+

AMO-LDPLN-111 ADMINISTRATION LCR DIALPLAN

DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 7 of 86
Access code for Overlap Sending Dial Plan, DPLN

<DISPLAY-LDPLN:TYPE=LDP,LDPNO=12;
DISPLAY-LDPLN:TYPE=LDP,LDPNO=12;
H500: AMO LDPLN STARTED
+--------------+-------------------------------------------------+
| | |
| LDPNO : 12 | LDP : 59-X |
| | SPC : 22 |
| | FDSFIELD : 0 SDSFIELD : 0 PINDP : N |
+------+-------+-------------------------------------------------+
| DPLN | LROUTE| LAUTH |
|------+-------+-------------------------------------------------+
| 0 | 27 | 1 |
| 1 | 27 | 1 |
| 2 | 27 | 1 |
| 3 | 27 | 1 |
| 4 | 27 | 1 |
| 5 | 27 | 1 |
| 6 | 27 | 1 |
| 7 | 27 | 1 |
| 8 | 27 | 1 |
| 9 | 27 | 1 |
| 10 | 27 | 1 |
| 11 | 27 | 1 |
| 12 | 27 | 1 |
| 13 | 27 | 1 |
| 14 | 27 | 1 |
| 15 | 27 | 1 |
+------+-------+-------------------------------------------------+

AMO-LDPLN-111 ADMINISTRATION LCR DIALPLAN

DISPLAY COMPLETED;

PSTN Dial Plan, DPLN

<DISPLAY-LDPLN:TYPE=LDP,LDPNO=5;
DISPLAY-LDPLN:TYPE=LDP,LDPNO=5;
H500: AMO LDPLN STARTED
+--------------+-------------------------------------------------+
| | |
| LDPNO : 5 | LDP : 9-1650-XXXXXXX |
| | SPC : 22 |
| | FDSFIELD : 0 SDSFIELD : 0 PINDP : N |
+------+-------+-------------------------------------------------+
| DPLN | LROUTE| LAUTH |
|------+-------+-------------------------------------------------+
| 0 | 165 | 1 |
| 1 | 165 | 1 |
| 2 | 165 | 1 |
| 3 | 165 | 1 |
| 4 | 165 | 1 |
| 5 | 165 | 1 |
| 6 | 165 | 1 |
| 7 | 165 | 1 |
| 8 | 165 | 1 |
| 9 | 165 | 1 |
| 10 | 165 | 1 |
| 11 | 165 | 1 |
| 12 | 165 | 1 |
| 13 | 165 | 1 |
| 14 | 165 | 1 |
| 15 | 165 | 1 |
+------+-------+-------------------------------------------------+

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 8 of 86
AMO-LDPLN-111 ADMINISTRATION LCR DIALPLAN
DISPLAY COMPLETED;

BCSU

PRI Board

<DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=3,SLOT=25;
DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=3,SLOT=25;
H500: AMO BCSU STARTED

ADDRESS : LTG 1 LTU 3 SOURCE GROUP 1

-----+-----------+---------+---+---+-+------------+-----+--------+------------+
| ASSIGNED | MODULE |FCT|HWY| | INSERTED | | | MODULE |
PEN | MODULE | TYPE |ID |BDL| | MODULE |STATE| HW-INFO| STATUS |
-----+-----------+---------+---+---+-+------------+-----+--------+------------+
25 | Q2196-X DIU-N2 1 A | | Q2196-X | 1 | -06 - | READY |

AMO-BCSU -111 BOARD CONFIGURATION, SWITCHING UNIT

DISPLAY COMPLETED;
<

PSTN board

<DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=2,SLOT=79;
DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=2,SLOT=79;
H500: AMO BCSU STARTED

ADDRESS : LTG 1 LTU 2 SOURCE GROUP 1

-----+-----------+---------+---+---+-+------------+-----+--------+------------+
| ASSIGNED | MODULE |FCT|HWY| | INSERTED | | | MODULE |
PEN | MODULE | TYPE |ID |BDL| | MODULE |STATE| HW-INFO| STATUS |
-----+-----------+---------+---+---+-+------------+-----+--------+------------+
79 | Q2196-X DIU-N2 1 A | | Q2196-X | 1 | -06 - | READY |

AMO-BCSU -111 BOARD CONFIGURATION, SWITCHING UNIT

DISPLAY COMPLETED;

Class of Trunk, COT

<dis-cot:22;
DIS-COT:22;
H500: AMO COT STARTED

COT: 22 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
PRIORITY FOR AC WILL BE DETERMINED FROM MESSAGE PRI
RECALL IF USER HANGS UP IN CONSULTATION CALL RCL
TRUNK CALL TRANSFER XFER
TRUNK SIGNALING ANSWER ANS
CHANGEOVER FROM HOLD TO RING TONE CHRT
KNOCKING OVERRIDE POSSIBLE KNOR
CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC
NETWORKWIDE AUTOMATIC CALLBACK ON BUSY CBBN
NETWORKWIDE AUTOMATIC CALLBACK ON FREE CBFN
DON'T RELEASE CALL TO BUSY HUNT GROUP BSHT
CONNECTION TO ROUTE OPTIMIZATION NODE ROPT
TSC-SIGNALING FOR NETWORKWIDE FEATURES (MANDATORY) TSCS
INCOMING CDR BY ZONE OR FROM LINE ICZL
AOC PER CALL (AUTOMATICAL OR ON REQUEST), MAND. CORNET-NQ AOCC
LINE WITH IMPLICIT NUMBERS LINO
NO TONE NTON

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 9 of 86
AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESSING
DISPLAY COMPLETED;

For Call Forwarding by Reroute need to add FNAN and FWDN to COT22
For Path Replacement need to add ROPT to COT 22 on the Hipath 4000.
<CHANGE-COT:COTNO=22,COTTYPE=COTADD,PAR=FNAN&FWDN;
CHANGE-COT:COTNO=22,COTTYPE=COTADD,PAR=FNAN&FWDN&ROPT;
H500: AMO COT STARTED
H07: CHANGED COT STILL LINKED WITH FOLLOWING TRUNKS:
COT TRUNK BCGR DEVICE
-----------------------------------
22 1- 3- 55- 0 1 CDGCONN
1- 3- 55- 1 1 CDGCONN
1- 3- 25- 0 1 S2CONN
1- 3- 25- 1 1 S2CONN
-----------------------------------
H06: COT 22 CHANGED

AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESSING

CHANGE COMPLETED;

<DISPLAY-COT:COTNO=22;
DISPLAY-COT:COTNO=22;
H500: AMO COT STARTED

COT: 22 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
PRIORITY FOR AC WILL BE DETERMINED FROM MESSAGE PRI
RECALL IF USER HANGS UP IN CONSULTATION CALL RCL
TRUNK CALL TRANSFER XFER
TRUNK SIGNALING ANSWER ANS
CHANGEOVER FROM HOLD TO RING TONE CHRT
KNOCKING OVERRIDE POSSIBLE KNOR
CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC
NETWORKWIDE AUTOMATIC CALLBACK ON BUSY CBBN
NETWORKWIDE AUTOMATIC CALLBACK ON FREE CBFN
NETWORKWIDE CALL FORWARDING PERMITTED FWDN
NETWORKWIDE FORWARDING NO-ANSWER FNAN
DON'T RELEASE CALL TO BUSY HUNT GROUP BSHT
CONNECTION TO ROUTE OPTIMIZATION NODE ROPT
TSC-SIGNALING FOR NETWORKWIDE FEATURES (MANDATORY) TSCS
INCOMING CDR BY ZONE OR FROM LINE ICZL
AOC PER CALL (AUTOMATICAL OR ON REQUEST), MAND. CORNET-NQ AOCC
LINE WITH IMPLICIT NUMBERS LINO
NO TONE NTON

AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESSING

DISPLAY COMPLETED;

Class of Parameter for Device Handler, COP

<DISPLAY-COP:COPNO=21;
DISPLAY-COP:COPNO=21;
H500: AMO COP STARTED

COP: 21 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
LINE WITH END-OF-DIAL EOD
SPECIAL MODE SFRM
CODE CALLING RELEASE AFTER EVERY TASK CCR
REGISTRATION OF LAYER 3 ADVISORIES L3AR

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 10 of 86
 CO TRUNK ACCESS:
TRUNK ACCESS TA

TOLL ACCESS:
TRUNK ACCESS TA

AMO-COP -111 CLASS OF PARAMETER FOR DEVICE HANDLER

DISPLAY COMPLETED;

Class of Service, COSSU

<DISPLAY-COSSU:TYPE=COS,COS=32;
DISPLAY-COSSU:TYPE=COS,COS=32;
H500: AMO COSSU STARTED
+------+-----------------+---------------+-----------------+
| COS | VOICE | FAX | DTE |
+------+-----------------+---------------+-----------------+
| 32 |> |
| | TA | NOCO | TA |
| | TNOTCR | NOTIE | TNOTCR |
| | | | BASIC |
| | | | MSN |
| | | | CDRINT |
| | | | MULTRA |
| | | | |
+------+-----------------+---------------+-----------------+
AMO-COSSU-111 CLASSES OF SERVICE
DISPLAY COMPLETED;
<DISPLAY-COSSU:TYPE=LCOSV,LCOSV=1;
DISPLAY-COSSU:TYPE=LCOSV,LCOSV=1;
H500: AMO COSSU STARTED
+----+----------------------------------------------------------------+-----+
|LCOS| LAUTH | |
| V | 1 2 3 4 5 6 | |
| |1234567890123456789012345678901234567890123456789012345678901234|COPIN|
| |>SERVICE INFORMATION | NUM |
+----+----+----|----+----|----+----|----+----|----+----|----+----|----+-----+
| 1|X...............................................................| 0 |
| |>LCR ATTENDANT FOR VOICE |
+----+----------------------------------------------------------------+-----+

AMO-COSSU-111 CLASSES OF SERVICE

DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 11 of 86
Trunk Group Access Code, BUEND

<DISPLAY-BUEND:TGRP=26,FORMAT=L;
DISPLAY-BUEND:TGRP=26,FORMAT=L;
H500: AMO BUEND STARTED

+------------------------------- FORMAT = L -----------------------------------+

| TGRP NUMBER : 26 TGRP NAME : PRI ECMA 3 MAXIMUM NO. : 30 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 9 DEVICE TYPE : S2CONN TRACENO : 0 |
| RESERVED : N SEARCH MODE : CIRCULAR ACD THRESHOLD : * |
| NUMBER OF ASSOCIATED ROUTES : 6 PRIORITY : 2 |
| TDDRFLAG : ON TDDRTHRESHOLD: 3 SOURCEGROUPIDX : 1 |
| GDTRRULE : 0 ACDPMGRP : 0 |
| THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEEN ALLOCATED: |
+------------------------------------------------------------------------------+
| 1- 3- 25-0 1 | 1- 3- 25-0 2 | 1- 3- 25-0 3 |
| 1- 3- 25-0 4 | 1- 3- 25-0 5 | 1- 3- 25-0 6 |
| 1- 3- 25-0 7 | 1- 3- 25-0 8 | 1- 3- 25-0 9 |
| 1- 3- 25-0 10 | 1- 3- 25-0 11 | 1- 3- 25-0 12 |
| 1- 3- 25-0 13 | 1- 3- 25-0 14 | 1- 3- 25-0 15 |
| 1- 3- 25-0 16 | 1- 3- 25-0 17 | 1- 3- 25-0 18 |
| 1- 3- 25-0 19 | 1- 3- 25-0 20 | 1- 3- 25-0 21 |
| 1- 3- 25-0 22 | 1- 3- 25-0 23 | 1- 3- 25-0 24 |
| 1- 3- 25-0 25 | 1- 3- 25-0 26 | 1- 3- 25-0 27 |
| 1- 3- 25-0 28 | 1- 3- 25-0 29 | 1- 3- 25-0 30 |
+------------------------------------------------------------------------------+

AMO-BUEND-111 TRUNK GROUP

DISPLAY COMPLETED;

<DISPLAY-BUEND:TGRP=27,FORMAT=L;
DISPLAY-BUEND:TGRP=27,FORMAT=L;
H500: AMO BUEND STARTED

+------------------------------- FORMAT = L -----------------------------------+

| TGRP NUMBER : 27 TGRP NAME : PRI ECMA 4 MAXIMUM NO. : 30 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 10 DEVICE TYPE : S2CONN TRACENO : 0 |
| RESERVED : N SEARCH MODE : CIRCULAR ACD THRESHOLD : * |
| NUMBER OF ASSOCIATED ROUTES : 4 PRIORITY : 2 |
| TDDRFLAG : ON TDDRTHRESHOLD: 3 SOURCEGROUPIDX : 1 |
| GDTRRULE : 0 ACDPMGRP : 0 |
| THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEEN ALLOCATED: |
+------------------------------------------------------------------------------+
| 1- 3- 25-1 1 | 1- 3- 25-1 2 | 1- 3- 25-1 3 |
| 1- 3- 25-1 4 | 1- 3- 25-1 5 | 1- 3- 25-1 6 |
| 1- 3- 25-1 7 | 1- 3- 25-1 8 | 1- 3- 25-1 9 |
| 1- 3- 25-1 10 | 1- 3- 25-1 11 | 1- 3- 25-1 12 |
| 1- 3- 25-1 13 | 1- 3- 25-1 14 | 1- 3- 25-1 15 |
| 1- 3- 25-1 16 | 1- 3- 25-1 17 | 1- 3- 25-1 18 |
| 1- 3- 25-1 19 | 1- 3- 25-1 20 | 1- 3- 25-1 21 |
| 1- 3- 25-1 22 | 1- 3- 25-1 23 | 1- 3- 25-1 24 |
| 1- 3- 25-1 25 | 1- 3- 25-1 26 | 1- 3- 25-1 27 |
| 1- 3- 25-1 28 | 1- 3- 25-1 29 | 1- 3- 25-1 30 |
+------------------------------------------------------------------------------+

AMO-BUEND-111 TRUNK GROUP

DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 12 of 86
Trunk Configuration, TDCSU

For Master-side Configuration

<dis-tdcsu:1-3-25-1;
DIS-TDCSU:1-3-25-1;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-03-025-1 TGRP = 27 |
|---------------------------------------------------------------------------|
| PROTVAR = ECMA1 INS = Y SRCHMODE = CIR |
| COTNO = 22 COPNO = 21 DPLN = 0 |
| ITR = 1 COS = 32 LCOSV = 1 |
| LCOSD = 1 CCT = PRI ECMA 4 DESTNO = 111 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 111 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 22 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729OPT SRCGRP = |
| TCCID = |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 LWPAR = 1 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| SVCDOM = |
| BCHAN = 1 && 30 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30

AMO-TDCSU-111 DIGITAL TRUNKS

DISPLAY COMPLETED;

<DISPLAY-LWPAR:FORMAT=L,BLNO=1,TYPE=DIUS2;
DISPLAY-LWPAR:FORMAT=L,BLNO=1,TYPE=DIUS2;
H500: AMO LWPAR STARTED

+-----------------------------------------------------------------------+
| LOADWARE PARAMETERS CIRCUIT TYPE: DIUS2 SOURCE:DB BLOCK: 1 |
+-----------------------------------------------------------------------+
| LNTYPE = COPPER VERSION = S2 QUAL = ON |
| MASTER = Y DCHAN1 = 16 DCHAN2 = 0 |
| PATTERN = D5H QUAL1 = 10 SEC. QUAL2 = 10 MIN. |
| SMD = Y PERMACT = Y FCBAB = DFH |
| CDG = N FIXEDTEI = 0 CNTRNR = 255 |
| TEIVERIF = N CRC4REP = N |
| DEV = INDEP |
| INFO = |
+-----------------------------------------------------------------------+

AMO-LWPAR-111 LOADWARE PARAMETERS FOR NETWORKING MODULES

DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 13 of 86
 For Slave-side Configuration

<dis-tdcsu:1-3-25-1;
DIS-TDCSU:1-3-25-1;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-03-025-1 TGRP = 27 |
|---------------------------------------------------------------------------|
| PROTVAR = ECMA1 INS = Y SRCHMODE = CIR |
| COTNO = 22 COPNO = 21 DPLN = 0 |
| ITR = 1 COS = 32 LCOSV = 1 |
| LCOSD = 1 CCT = PRI ECMA 4 DESTNO = 111 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 111 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 22 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729OPT SRCGRP = |
| TCCID = |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 LWPAR = 0 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| SVCDOM = |
| BCHAN = 1 && 30 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30

AMO-TDCSU-111 DIGITAL TRUNKS

DISPLAY COMPLETED;

<DISPLAY-LWPAR:FORMAT=L,BLNO=0,TYPE=DIUS2;
DISPLAY-LWPAR:FORMAT=L,BLNO=0,TYPE=DIUS2;
H500: AMO LWPAR STARTED

+-----------------------------------------------------------------------+
| LOADWARE PARAMETERS CIRCUIT TYPE: DIUS2 SOURCE:DB BLOCK: 0 |
+-----------------------------------------------------------------------+
| LNTYPE = COPPER VERSION = S2 QUAL = ON |
| MASTER = N DCHAN1 = 16 DCHAN2 = 0 |
| PATTERN = D5H QUAL1 = 10 SEC. QUAL2 = 10 MIN. |
| SMD = N PERMACT = Y FCBAB = DFH |
| CDG = N FIXEDTEI = 0 CNTRNR = 255 |
| TEIVERIF = N CRC4REP = N |
| DEV = INDEP |
| INFO = |
+-----------------------------------------------------------------------+

AMO-LWPAR-111 LOADWARE PARAMETERS FOR NETWORKING MODULES

DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 14 of 86
PSTN Trunk Configuration, TDCSU

<dis-tdcsu:1-2-79-1;
DIS-TDCSU:1-2-79-1;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-02-079-1 TGRP = 23 |
|---------------------------------------------------------------------------|
| PROTVAR = ETSI INS = Y SRCHMODE = CIR |
| COTNO = 21 COPNO = 21 DPLN = 0 |
| ITR = 1 COS = 10 LCOSV = 32 |
| LCOSD = 32 CCT = PRI ECMA 2 DESTNO = 100 |
| SEGMENT = 8 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 21 FWDX = 10 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729OPT SRCGRP = |
| TCCID = |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 LWPAR = 1 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| SVCDOM = |
| BCHAN = 1 && 30 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30

AMO-TDCSU-111 DIGITAL TRUNKS

DISPLAY COMPLETED;

Trunk Configuration to Hicom node, TDCSU

<DISPLAY-TDCSU:PEN1=1-3-25-0;
DISPLAY-TDCSU:PEN1=1-3-25-0;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-03-025-0 TGRP = 26 |
|---------------------------------------------------------------------------|
| PROTVAR = PSS1V2 INS = Y SRCHMODE = CIR |
| COTNO = 22 COPNO = 21 DPLN = 0 |
| ITR = 1 COS = 32 LCOSV = 1 |
| LCOSD = 1 CCT = PRI ECMA 3 DESTNO = 222 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 222 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 22 FWDX = 10 |
| DOMTYPE = DOMAINNO = TPROFNO = |

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 15 of 86
 | INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729OPT SRCGRP = |
| TCCID = |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 LWPAR = 1 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| SVCDOM = |
| BCHAN = 1 && 30 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30

AMO-TDCSU-111 DIGITAL TRUNKS

DISPLAY COMPLETED;

Reference Clock Configuration, REFTA

For Master-side Configuration

<DISPLAY-REFTA:TYPE=CIRCUIT,PEN=1-3-25-1,KIND=ALL;
DISPLAY-REFTA:TYPE=CIRCUIT,PEN=1-3-25-1,KIND=ALL;
H500: AMO REFTA STARTED
+-------------------------------------------------------------------------+
| R E F E R E N C E C L O C K C I R C U I T S |
+--------------+---------+----------+---+------+------+------+-----+------+
| PEN | MODULE | DEVICE |PRI|ERROR |BLOCK |SUPP. |READY|SRCGRP|
| | | | | | | |BUT | |
| | | | | | | |ASYN.| |
+--------------+---------+----------+---+------+------+------+-----+------+
| 1- 3- 25- 1 | DIU-N2 | S2CONN | 0| 0| N | | N | 1|
+--------------+---------+----------+---+------+------+------+-----+------+

AMO-REFTA-111 REFERENCE CLOCK TABLE

DISPLAY COMPLETED;

For Slave-side Configuration

<DISPLAY-REFTA:TYPE=CIRCUIT,PEN=1-3-25-1,KIND=ALL;
DISPLAY-REFTA:TYPE=CIRCUIT,PEN=1-3-25-1,KIND=ALL;
H500: AMO REFTA STARTED
+-------------------------------------------------------------------------+
| R E F E R E N C E C L O C K C I R C U I T S |
+--------------+---------+----------+---+------+------+------+-----+------+
| PEN | MODULE | DEVICE |PRI|ERROR |BLOCK |SUPP. |READY|SRCGRP|
| | | | | | | |BUT | |
| | | | | | | |ASYN.| |
+--------------+---------+----------+---+------+------+------+-----+------+
| 1- 3- 25- 1 | DIU-N2 | S2CONN | 11| 0| N | | N | 1|
+--------------+---------+----------+---+------+------+------+-----+------+

AMO-REFTA-111 REFERENCE CLOCK TABLE

DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 16 of 86
Trunk Least Cost Routing Configuration

LDAT

<DISPLAY-LDAT:TYPE=LCR,LROUTE=1;
DISPLAY-LDAT:TYPE=LCR,LROUTE=1;
H500: AMO LDAT STARTED
+--------------------------------------------------------------------------+
| LROUTE = 1 LDPLN NAME = ROPTCCM SERVICE = ALL |
| TYPE = LCR DNNO OF ROUTE = 111 |
| SERVICE INFO = |
+-------+-----+-----+-----+------+----------+------------+----------+------+
| | | | | | SCHEDULE | CARRIER | | |
| LRTEL | LVAL| TGRP| ODR| LAUTH| ABCDEFGH | ZONE | LATTR | LDSRT|
+-------+-----+-----+-----+------+----------+------------+----------+------+
| 1 | 1| 27| 111| 1 | ******** | 1 EMPTY | NONE | |
| | DNNO = 111 |
+-------+-----+-----+-----+------+----------+------------+----------+------+

AMO-LDAT -111 LCR-DIRECTIONS

DISPLAY COMPLETED;

<DISPLAY-LDAT:TYPE=LCR,LROUTE=26;
DISPLAY-LDAT:TYPE=LCR,LROUTE=26;
H500: AMO LDAT STARTED
+--------------------------------------------------------------------------+
| LROUTE = 26 NAME = PRI 3 ECMA1 SERVICE = ALL |
| TYPE = LCR DNNO OF ROUTE = 111 |
| SERVICE INFO = |
+-------+-----+-----+-----+------+----------+------------+----------+------+
| | | | | | SCHEDULE | CARRIER | | |
| LRTEL | LVAL| TGRP| ODR| LAUTH| ABCDEFGH | ZONE | LATTR | LDSRT|
+-------+-----+-----+-----+------+----------+------------+----------+------+
| 1 | 1| 26| 15| 3 | ******** | 1 EMPTY | NONE | |
+-------+-----+-----+-----+------+----------+------------+----------+------+

AMO-LDAT -111 LCR-DIRECTIONS

DISPLAY COMPLETED;

<DISPLAY-LDAT:TYPE=LCR,LROUTE=27;
DISPLAY-LDAT:TYPE=LCR,LROUTE=27;
H500: AMO LDAT STARTED
+--------------------------------------------------------------------------+
| LROUTE = 27 LDPLN NAME = PRI 4 ECMA1 SERVICE = ALL |
| TYPE = LCR DNNO OF ROUTE = 111 |
| SERVICE INFO = |
+-------+-----+-----+-----+------+----------+------------+----------+------+
| | | | | | SCHEDULE | CARRIER | | |
| LRTEL | LVAL| TGRP| ODR| LAUTH| ABCDEFGH | ZONE | LATTR | LDSRT|
+-------+-----+-----+-----+------+----------+------------+----------+------+
| 1 | 1| 27| 15| 1 | ******** | 1 EMPTY | NONE | |
+-------+-----+-----+-----+------+----------+------------+----------+------+

AMO-LDAT -111 LCR-DIRECTIONS

DISPLAY COMPLETED;
<DISPLAY-LDAT:TYPE=LCR,LROUTE=165;
DISPLAY-LDAT:TYPE=LCR,LROUTE=165;
H500: AMO LDAT STARTED
+--------------------------------------------------------------------------+
| LROUTE = 165 LDPLN NAME = PSTN 91650 SERVICE = ALL |
| TYPE = LCR DNNO OF ROUTE = 89 |
| SERVICE INFO = |

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 17 of 86
 +-------+-----+-----+-----+------+----------+------------+----------+------+
| | | | | | SCHEDULE | CARRIER | | |
| LRTEL | LVAL| TGRP| ODR| LAUTH| ABCDEFGH | ZONE | LATTR | LDSRT|
+-------+-----+-----+-----+------+----------+------------+----------+------+
| 1 | 1| 23| 50| 1 | ******** | 1 EMPTY | NONE | |
| | DNNO = 89 |
+-------+-----+-----+-----+------+----------+------------+----------+------+

AMO-LDAT -111 LCR-DIRECTIONS

DISPLAY COMPLETED;

RICHT

DISPLAY-RICHT:MODE=LRTE,LRTE=1;
H500: AMO RICHT STARTED
+-----------------------------------------------------------------+
| LRTE = 1 NAME = ROPTCCM (NEUTRAL) LSVC = ALL |
| DNNO = 111 PDNNO = 0 DESTNO =111 |
| ROUTOPT = YES REROUT = YES PLB = NO FWDBL = NO |
| DTMFCNV = WITHOUT DTMFDSP = WITHOUT DTMFTEXT = |
| DTMFPULS = BUGS = LIN ROUTATT = NO MAINGRP = 24 |
| EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 24 |
| INFO = |
| NOPRCFWD = NO |
+-----------------------------------------------------------------+
| TGRP = 27 LDAT PRI ECMA 4 (NEUTRAL) SUBGROUP = 10 |
+-----------------------------------------------------------------+

AMO-RICHT-111 TRUNK ROUTING

DISPLAY COMPLETED;

<DISPLAY-RICHT:MODE=LRTE,LRTE=26;
DISPLAY-RICHT:MODE=LRTE,LRTE=26;
H500: AMO RICHT STARTED
+-----------------------------------------------------------------+
| LRTE = 26 NAME = PRI 3 ECMA1 (NEUTRAL) LSVC = ALL |
| DNNO = 111 PDNNO = 0 |
| ROUTOPT = YES REROUT = YES PLB = NO FWDBL = NO |
| DTMFCNV = WITHOUT DTMFDSP = WITHOUT DTMFTEXT = |
| DTMFPULS = BUGS = LIN ROUTATT = NO MAINGRP = 14 |
| EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 14 |
| INFO = |
| NOPRCFWD = NO |
+-----------------------------------------------------------------+
| TGRP = 26 LDAT PRI ECMA 3 (NEUTRAL) SUBGROUP = 9 |
+-----------------------------------------------------------------+

AMO-RICHT-111 TRUNK ROUTING

DISPLAY COMPLETED;

<DISPLAY-RICHT:MODE=LRTE,LRTE=27;
DISPLAY-RICHT:MODE=LRTE,LRTE=27;
H500: AMO RICHT STARTED
+-----------------------------------------------------------------+
| LRTE = 27 NAME = PRI 4 ECMA1 (NEUTRAL) LSVC = ALL |
| DNNO = 111 PDNNO = 0 |
| ROUTOPT = YES REROUT = YES PLB = NO FWDBL = NO |
| DTMFCNV = FIX DTMFDSP = WITHOUT DTMFTEXT = |
| DTMFPULS = PP300 BUGS = LIN ROUTATT = NO MAINGRP = 15 |
| EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 15 |
| INFO = |
| NOPRCFWD = NO |
+-----------------------------------------------------------------+
| TGRP = 27 LDAT PRI ECMA 4 (NEUTRAL) SUBGROUP = 10 |
+-----------------------------------------------------------------+

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 18 of 86
AMO-RICHT-111 TRUNK ROUTING
DISPLAY COMPLETED;

PSTN RICHT

<DISPLAY-RICHT:MODE=LRTE,LRTE=165;
DISPLAY-RICHT:MODE=LRTE,LRTE=165;
H500: AMO RICHT STARTED
+-----------------------------------------------------------------+
| LRTE = 165 NAME = PSTN 91650 (NEUTRAL) LSVC = ALL |
| DNNO = 89 PDNNO = 0 DESTNO = 89 |
| ROUTOPT = YES REROUT = YES PLB = NO FWDBL = NO |
| DTMFCNV = WITHOUT DTMFDSP = WITHOUT DTMFTEXT = |
| DTMFPULS = BUGS = LIN ROUTATT = NO MAINGRP = 27 |
| EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 27 |
| INFO = |
| NOPRCFWD = NO |
+-----------------------------------------------------------------+
| TGRP = 23 LDAT ECMA 2 (NEUTRAL) SUBGROUP = 6 |
+-----------------------------------------------------------------+

AMO-RICHT-111 TRUNK ROUTING

DISPLAY COMPLETED;

LCR Out-dial Rules, LODR

<DISPLAY-LODR:ODR=111,FORMAT=L;
H500: AMO LODR STARTED
+-------------------------------------------------------+
| ODR POSITION CMD PARAMETER |
+--------+----------------------------------------------+
| 111 | 1 ECHO 1 |
| | 2 ECHO 2 |
| | 3 END |
+--------+----------------------------------------------+
H03: THE NEXT FREE ODR IS 2

AMO-LODR -111 ADMINISTRATION OF LCR OUTDIAL RULES

DISPLAY COMPLETED;
<DISPLAY-LODR:ODR=15,FORMAT=L;
DISPLAY-LODR:ODR=15,FORMAT=L;
H500: AMO LODR STARTED
+-------------------------------------------------------+
| ODR POSITION CMD PARAMETER |
+--------+----------------------------------------------+
| 15 | 1 ECHO 2 |
| | 2 END |
+--------+----------------------------------------------+
H03: THE NEXT FREE ODR IS 2

AMO-LODR -111 ADMINISTRATION OF LCR OUTDIAL RULES

DISPLAY COMPLETED;
<DISPLAY-LODR:ODR=50,FORMAT=L;
DISPLAY-LODR:ODR=50,FORMAT=L;
H500: AMO LODR STARTED
+-------------------------------------------------------+
| ODR POSITION CMD PARAMETER |
+--------+----------------------------------------------+
| 50 | 1 ECHO 2 |
| | 2 ECHO 3 |

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 19 of 86
 | | 3 END |
+--------+----------------------------------------------+
H03: THE NEXT FREE ODR IS 2

AMO-LODR -111 ADMINISTRATION OF LCR OUTDIAL RULES

DISPLAY COMPLETED;

In-Band DTMF signaling:

In order to enable In-band DTMF signaling on digital stations for Voicemail applications, the station configuration has
to be changed so that the parameter DTMFCTRD=Y.
Name and Number Restrictions:

To use Name and Number Restrictions, the station configuration should be changed so that the parameter
SSTNO=Y, (Secret Station Number must be set to Yes).
<dis-sbcsu:5002;
DIS-SBCSU:5002;
H500: AMO SBCSU STARTED

---------------------------- USER DATA ---------------------------------------

STNO =5002 OPT =OPTI COS1 =2 DPLN =1
MAINO =5002 CONN =DIR COS2 =2 ITR =1
PEN = 1- 3- 31- 2 LCOSV1 =6 COSX =0
INS =Y ASYNCT =500 LCOSV2 =6
PERMACT = LCOSD1 =6
SSTNO =Y EXTBUS = LCOSD2 =6 CBKBMAX =5
TRACE =N RCBKB =N
ALARMNO =0 DFSVCANA= SPDI =0 RCBKNA =N
HMUSIC =0 FLASH = SPDC1 = CBKNAMB =Y
PMIDX =0 SPDC2 =
COMGRP =0
SECR =N DIGNODIS=N DSSTNA =N
STD =55 CALLOG =NONE DSSTNB =Y TEXTSEL =ENGLISH

REP =0 OPTICOM =N OPTIUSB :0 VPI =

IDCR =N OPTICA =1 OPTIS0A : VCI =
OPTIDA = OPTISPA :0 PATTERN =
OPTIABA :0
DCFWBUSY=N HEADSET =N APICLASS=
DNIDSP =N HSKEY =NORMAL ACFAPPL =0
DTMFBLK =N IPPASSW =
DTMFCTRD=Y BASICSVC=
DVCFIG =OPTIP500 TSI =1 SPROT = SOPTIDX =
DPROT = DOPTIDX =
FPROT = FOPTIDX =
------------------- ACTIVATION IDENTIFIERS FOR FEATURES ----------------------
FWDS :N HTOS :N DND :N
FWDD :N HTOD :N VCP :Y TWLOGIN :N
FWDF :N HTOF :N CWT :N
------------------- FEATURES AND GROUP MEMBERSHIPS ---------------------------
PUGR : ESSTN :
KEYSYS :N NOPTNO :
HUNT CD :N
------------------- SUBSCRIBER ATTRIBUTES (AMO SDAT) -------------------------
NONE
------------------------------------------------------------------------------

AMO-SBCSU-111

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 20 of 86
Configure Digital Station for MWI Application:

To get the MWI light to work, the station configuration should be changed so that the parameter PMIDX (phoneMail
Index parameter) needs to point to the IDX identifier that identifies the Message Center’s Service Access Number.
<dis-sbcsu:5002;
DIS-SBCSU:5002;
H500: AMO SBCSU STARTED

---------------------------- USER DATA ---------------------------------------

STNO =5002 OPT =OPTI COS1 =2 DPLN =1
MAINO =5002 CONN =DIR COS2 =2 ITR =1
PEN = 1- 3- 31- 2 LCOSV1 =6 COSX =0
INS =Y ASYNCT =500 LCOSV2 =6
PERMACT = LCOSD1 =6
SSTNO =N EXTBUS = LCOSD2 =6 CBKBMAX =5
TRACE =N RCBKB =N
ALARMNO =0 DFSVCANA= SPDI =0 RCBKNA =N
HMUSIC =0 FLASH = SPDC1 = CBKNAMB =Y
PMIDX =1 SPDC2 =
COMGRP =0
SECR =N DIGNODIS=N DSSTNA =N
STD =55 CALLOG =NONE DSSTNB =Y TEXTSEL =ENGLISH

REP =0 OPTICOM =N OPTIUSB :0 VPI =

IDCR =N OPTICA =1 OPTIS0A : VCI =
OPTIDA = OPTISPA :0 PATTERN =
OPTIABA :0
DCFWBUSY=N HEADSET =N APICLASS=
DNIDSP =N HSKEY =NORMAL ACFAPPL =0
DTMFBLK =N IPPASSW =
DTMFCTRD=Y BASICSVC=
DVCFIG =OPTIP500 TSI =1 SPROT = SOPTIDX =
DPROT = DOPTIDX =
FPROT = FOPTIDX =
------------------- ACTIVATION IDENTIFIERS FOR FEATURES ----------------------
FWDS :N HTOS :N DND :N
FWDD :N HTOD :N VCP :Y TWLOGIN :N
FWDF :N HTOF :N CWT :N
------------------- FEATURES AND GROUP MEMBERSHIPS ---------------------------
PUGR : ESSTN :
KEYSYS :N NOPTNO :
HUNT CD :N
------------------- SUBSCRIBER ATTRIBUTES (AMO SDAT) -------------------------
NONE
------------------------------------------------------------------------------

AMO-SBCSU-111

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 21 of 86
Configure Message Center’s Service Access Number for MWI Application:

Since the MWI was tested with the Message Center integrated on Cisco Communication Manager side, the PBX
needs to configure an identifier for the Message Center’s Service Access Number in order for the MWI light to work.
Without this identifier the MWI light will not work.

<ADD-RICHT:MODE=PM,IDX=1,SAN=4005;
ADD-RICHT:MODE=PM,IDX=1,SAN=4005;
H500: AMO RICHT STARTED

AMO-RICHT-111 TRUNK ROUTING

ADD COMPLETED;
<DISP-RICH:MODE=PM;
S3: DATA SUBSYSTEM FOR AMO RICH NOT FOUND ON HARD DISK

<DISP-RICHT
MODE = PM
DISP-RICHT:PM;
H500: AMO RICHT STARTED
+------+----------------------+------------------------------+--------+
| IDX | SAN | NAME | TYPE |
+------+----------------------+------------------------------+--------+
| 1|4005 | |OTHER |
+------+----------------------+------------------------------+--------+

AMO-RICHT-111 TRUNK ROUTING

DISPLAY COMPLETED;
<

Configure Digital Station’s Class of Service for Mailbox MWI application

<DISPLAY-COSSU:TYPE=COS,COS=2,FORMAT=L;
DISPLAY-COSSU:TYPE=COS,COS=2,FORMAT=L;
H500: AMO COSSU STARTED
+------+-----------------+---------------+-----------------+
| COS | VOICE | FAX | DTE |
+------+-----------------+---------------+-----------------+
| 2 |> |
| | TA | NOCO | TA |
| | TSUID | NOTIE | TNOTCR |
| | TNOTCR | BASIC | BASIC |
| | CDRINT | | |
| | CDRS | | |
| | CDRC | | |
| | MB | | |
| | COSXCD | | |
| | VCE | | |
| | SPKR | | |
| | DATA | | |
| | FWDNWK | | |
| | RERING | | |
| | CDRIND | | |
| | MSN | | |
| | FWDECA | | |
| | FWDBAS | | |
| | FWDDIR | | |
| | CFB | | |
| | CFNR | | |
| | CCBS | | |
| | CW | | |
| | FWDEXT | | |

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 22 of 86
 | | GRPCAL | | |
| | SUTVA | | |
| | | | |
+------+-----------------+---------------+-----------------+
AMO-COSSU-111 CLASSES OF SERVICE
DISPLAY COMPLETED;

<DISPLAY-PERSI:TYPE=NAME,STNO=5002;
DISPLAY-PERSI:TYPE=NAME,STNO=5002;
H500: AMO PERSI STARTED
+--------+-----------------------------------------+---------------------------+
| STNO | CHRISTIAN AND SURNAME CHARCON | ORGANIZATIONAL UNIT |
+--------+-----------------------------------------+---------------------------+
| | | |
| 5002 | HIPATH DT2* | |
| | | |
+--------+-----------------------------------------+---------------------------+

AMO-PERSI-111 PERSONAL IDENTIFICATION DATA

DISPLAY COMPLETED;

Siemens HiPath 4000 Software Release

<
<dis-dbc:verbose=n;
DIS-DBC:VERBOSE=N;
H500: AMO DBC STARTED
+------------------------------------------------------------------------------+
| SYSTEM CLASSIFICATION : SYSTEM 80 (H80 ) |
| HARDWARE ASSEMBLY : EXTENDED COMPACT CXE (CXE ) |
| OPERATING MODE : SIMPLEX |
| RESTART TYPE : SYM |
| HW-ARCHITECTURE : 4300 |
| HW-ARCHITECTURE TYPE : 2 |
| |
| 'NO OF' HW VALUES |
| LTG'S : 1 LTU'S : 4 LOG.LINES : 12000 MTS BD /GSN: 1 |
| SIUP'S/LTU: 4 TMD24'S PER LTU: 4 PHYS.PORTS: 6000 HWY /MTS BD: 64 |
| HDLC /DCL : 5 PBC /DCL : 1 PBC'S : 17 |
| LOG. SIU LINES : 26 |
| LOG. CONF LINES : 35 |
| LOG. DCL LINES : 36 |
| DB DIMENSIONING-NAME : SMALL CONF-TABLE VERSION: 1 |
| DB SUSY'S: |
| SWITCH NUMBER : L31903Q1930A00001 |
| LOCATION : CUSTOMER |
| BAPPL : BSMONO |
| DBAPPL : DBSMALL |
| SYSTEM_ID : |
| |
| OVERLAY RESOURCES IN ADP: |
| SLOTS : 1000 MEMORY SPACE : 2000 KB |
| OVERLAY RESOURCES IN SWU: |
| SLOTS : 1000 MEMORY SPACE : 2000 KB |
| OVERLAY RESOURCES BEI MONO PROCESSING: |
| SLOTS : 400 MEMORY SPACE : 3000 KB |
+------------------------------------------------------------------------------+

AMO-DBC -111 DATABASE CONFIGURATION

DISPLAY COMPLETED;

<disp-vegas:list=long;
DISP-VEGAS:LIST=LONG;
H500: AMO VEGAS STARTED
SYSTEM NO. AMO APS NO. START USER STATUS

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 23 of 86
SWU: L31903Q1930A00001 --- P30252B4500B00105 00.00.00 00:00 NOBODY FREE
SWU RES CODE APS: P30252B4500S00105 (DIR FILE: :PDS:APSI/PS/S0-EM0SC)
SWU AMO CODE APS: P30252B4500B00105 (DIR FILE: :PDS:APSI/PS/B0-EM0BC)
SWU AMO TEXT APS: P30252B4500B00105 (DIR FILE: :PDS:APSI/PS/B0-EM0BC)
BREAK MARK : NO
RESERVATION : NO
ADS: L31903Q1930A00001 --- P30252B4500A00105 00.00.00 00:00 NOBODY FREE
ADS RES CODE APS: P30252B4500D00105 (DIR FILE: :PDS:APSI/PS/D0-EM0DC)
ADS AMO CODE APS: P30252B4500A00105 (DIR FILE: :PDS:APSI/PS/A0-EM0AC)
ADS AMO TEXT APS: P30252B4500A00105 (DIR FILE: :PDS:APSI/PS/A0-EM0AC)
BREAK MARK : NO
RESERVATION : NO

AMO-VEGAS-111 ADMIN. OF DATABASE GENERATION RUNS ON SUPPORT SYSTEM

DISPLAY COMPLETED;

<DISPLAY-APS:ANS=Y,TYPE=PSALL,SP="Y0-EM0YC";
DISPLAY-APS:ANS=Y,TYPE=PSALL,SP="Y0-EM0YC";
H500: AMO APS STARTED
ADINIT STARTED
PROGRAM SYSTEM : Y0-EM0YC
VERSION NUMBER : 10
CORRECTION VERSION NUMBER : 001
PART NUMBER : P30252N4505B00005
PROGRAM SYSTEM WITH CODE SUBSYSTEMS
INTERFACE VERSION:
PROGRAM SYSTEM DOES NOT CONTAIN ANY INTERFACE VERSIONS

ADINIT COMPLETED
STATUS = H'0000
AMO-APS -111 SOFTWARE LOAD UPGRADE
DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 24 of 86
Configuring the Cisco Unified Communication Manager
CUCM ECMA Service Parameter Configuration.

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 25 of 86
CUCM Version

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 26 of 86
CMM-E1 Gateway Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 27 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 28 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 29 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 30 of 86
Partition Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 31 of 86
Calling Search Space

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 32 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 33 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 34 of 86
Enbloc Route Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 35 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 36 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 37 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 38 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 39 of 86
Overlap Sending Route Pattern Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 40 of 86
PSTN Route Pattern Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 41 of 86
Translation Pattern for Incoming Calls

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 42 of 86
CLIR Route Pattern Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 43 of 86
CNIR Route Pattern Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 44 of 86
COLR Translation Pattern Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 45 of 86
CONR Translation Pattern Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 46 of 86
MWI lamp On/Off Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 47 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 48 of 86
Voice Mail Profile Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 49 of 86
Voice Mail Pilot Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 50 of 86
Voice Mail Ports List

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 51 of 86
Voice Mail Port Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 52 of 86
CallBack Service Parameters

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 53 of 86
CallBack Softkey Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 54 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 55 of 86
IDivert Softkey Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 56 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 57 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 58 of 86
Path Replacement Service Parameters

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 59 of 86
PR Call Pick Up Group

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 60 of 86
Forward by Reroute Service Parameter

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 61 of 86
IP 7960 SCCP phone Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 62 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 63 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 64 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 65 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 66 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 67 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 68 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 69 of 86
IP 7961 SIP phone Configuration

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 70 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 71 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 72 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 73 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 74 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 75 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 76 of 86
 © 2007 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 77 of 86
Configuring the CMM-E1 gateway
VENUS-CMM-E1#sh ver
VENUS-CMM-E1#sh version
Cisco IOS Software, Cat6K-lc Software (wscmm-IPVOICE-M), Version 12.4(5a), RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Sat 14-Jan-06 04:52 by alnguyen

ROM: System Bootstrap, Version 12.2(1r)T2, RELEASE SOFTWARE (fc1)

VENUS-CMM-E1 uptime is 1 day, 2 hours, 34 minutes

System returned to ROM by power-on
System image file is "bootflash:wscmm-ipvoice-mz.124-5a.bin"

cisco WS-SVC-CMM Cat6k Voice Linecard (R7000) processor (revision 0xFF) with 196
608K/65536K bytes of memory.
Processor board ID SAD0825032A
R7000 CPU at 400MHz, Implementation 39, Rev 3.3, 256KB L2 Cache
Last reset from power-on
1 FastEthernet interface
1 Gigabit Ethernet interface
206 Serial interfaces
6 Channelized E1/PRI ports
6 Channelized T1/PRI ports
32768K bytes of processor board bootflash (Read/Write)

Configuration register is 0x2

VENUS-CMM-E1#
VENUS-CMM-E1#sh run
Building configuration...

Current configuration : 4329 bytes

!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname VENUS-CMM-E1
!
boot-start-marker
boot-end-marker
!
enable password cisco
!
no aaa new-model
!
resource policy

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 78 of 86
!
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
!
!
no ip domain lookup
ip host CM-CHIVAS 172.20.8.254
ip host CM-BARZA 172.20.110.254
ip host CM-MERCURY 172.20.215.254
ip host CM-VENUS 172.20.214.254
!
isdn switch-type primary-4ess
!
!
!
!
controller T1 1/0
framing esf
linecode b8zs
pri-group timeslots 1-24 service mgcp
!
controller T1 1/1
framing esf
linecode b8zs
pri-group timeslots 1-24 service mgcp
!
controller T1 1/2
framing esf
linecode b8zs
pri-group timeslots 1-24 service mgcp
!
controller T1 1/3
framing esf
linecode b8zs
pri-group timeslots 1-24 service mgcp
!
controller T1 1/4
framing esf
linecode b8zs
pri-group timeslots 1-24 service mgcp
!
controller T1 1/5
framing esf
linecode b8zs
pri-group timeslots 1-24 service mgcp
!
controller E1 2/0
pri-group timeslots 1-31 service mgcp
!
controller E1 2/1
pri-group timeslots 1-31 service mgcp
!

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 79 of 86
controller E1 2/2
!
controller E1 2/3
!
controller E1 2/4
!
controller E1 2/5
!
!
!
interface GigabitEthernet1/0
ip address 172.20.214.51 255.255.255.0
no ip proxy-arp
no negotiation auto
no keepalive
!
interface Serial1/0:23
no ip address
encapsulation hdlc
no logging event link-status
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
interface Serial1/1:23
no ip address
encapsulation hdlc
no logging event link-status
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
interface Serial1/2:23
no ip address
encapsulation hdlc
no logging event link-status
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
interface Serial1/3:23
no ip address
encapsulation hdlc
no logging event link-status
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
interface Serial1/4:23
no ip address

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 80 of 86
 encapsulation hdlc
no logging event link-status
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
interface Serial1/5:23
no ip address
encapsulation hdlc
no logging event link-status
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
interface Serial2/0:15
no ip address
encapsulation hdlc
no logging event link-status
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
interface Serial2/1:15
no ip address
encapsulation hdlc
no logging event link-status
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
ip default-gateway 172.20.8.1
ip route 0.0.0.0 0.0.0.0 172.20.8.1
ip route 0.0.0.0 0.0.0.0 172.20.215.1
ip route 0.0.0.0 0.0.0.0 172.20.214.1
!
no ip http server
!
!
control-plane
!
!
voice-port 1/0:23
!
voice-port 1/1:23
!
voice-port 1/2:23
!
voice-port 1/3:23
!
voice-port 1/4:23

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 81 of 86
!
voice-port 1/5:23
!
voice-port 2/0:15
!
voice-port 2/1:15
!
ccm-manager mgcp
ccm-manager music-on-hold
ccm-manager config server CM-VENUS
ccm-manager config
!
mgcp
mgcp call-agent CM-VENUS 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
no mgcp package-capability res-package
mgcp package-capability sst-package
mgcp package-capability pre-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
!
mgcp profile default
!
!
!
!
dial-peer voice 1 pots
service mgcpapp
port 1/0:23
!
dial-peer voice 2 pots
service mgcpapp
port 1/1:23
!
dial-peer voice 3 pots
service mgcpapp
port 1/2:23
!
dial-peer voice 4 pots
service mgcpapp
port 1/3:23
!
dial-peer voice 5 pots
service mgcpapp
port 1/4:23
!
dial-peer voice 6 pots
service mgcpapp
port 1/5:23

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 82 of 86
!
dial-peer voice 7 pots
service mgcpapp
port 2/0:15
!
dial-peer voice 8 pots
service mgcpapp
port 2/1:15
!
!
line con 0
password cisco
line vty 0 4
password cisco
login
!
!
end

VENUS-CMM-E1#

Acronyms

Acronym Definitions
ANF-PR Additional Network Feature Path Replacement
AOC Advice-of-charge. Information element is sent with the connection setup information for
incoming Euro-ISDN connections. The AOC IE is used for call charge calculation.
CUCM Cisco Unified Communication Manager
CCBS Call Completion to Busy Subscriber
CCNR Call Completion on No Reply
CFB Call Forwarding on Busy
CFNR Call Forwarding No Reply
CFU Call Forwarding Unconditional
CLIP Calling Line (Number) Identification Presentation
CLIR Calling Line (Number) Identification Restriction
CMM Communication Media Module (CMM) is a Cisco Catalyst® 6500 Series and Cisco 7600
Series line card that provides flexible and high-density T1/E1 gateways
CNIP Calling Name Identification Presentation
CNIR Calling Name Identification Restriction
COLP Connected Line (Number) Identification Presentation
COLR Connected Line (Number) Identification Restriction
CONP Connected Name Identification Presentation
CONR Connected Name Identification Restriction
CT Call Transfer
MWI Message Waiting Indicator

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 83 of 86
PSTN Public Switched Telephone Network

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 84 of 86
Important Information
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE

WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO

BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE

FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR

INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA

ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 85 of 86
Corporate European Americas Asia Pacific
Headquarters Headquarters Headquarters Headquarters
Cisco Systems, Inc. Cisco Systems International Cisco Systems, Inc. Cisco Systems, Inc.
170 West Tasman Drive BV 170 West Tasman Drive Capital Tower
San Jose, CA 95134-1706 Haarlerbergpark San Jose, CA 95134-1706 168 Robinson Road
USA Haarlerbergweg 13-19 USA #22-01 to #29-01
www.cisco.com 1101 CH Amsterdam www.cisco.com Singapore 068912
Tel: 408 526-4000 The Netherlands Tel: 408 526-7660 www.cisco.com
800 553-NETS (6387) www-europe.cisco.com Fax: 408 527-0883 Tel: +65 317 7777
Fax: 408 526-4100 Tel: 31 0 20 357 1000 Fax: +65 317 7799
Fax: 31 0 20 357 1100
Cisco Systems has more than 200 offices in the following countries and regions. Addresses, phone numbers, and fax numbers are listed on
the Cisco Web site at www.cisco.com/go/offices.

Argentina • Australia • Austria • Belgium • Brazil • Bulgaria • Canada • Chile • China PRC • Colombia • Costa Rica • Croatia • Czech
Republic • Denmark • Dubai, UAE • Finland • France • Germany • Greece • Hong Kong SAR • Hungary • India • Indonesia • Ireland •
Israel • Italy • Japan • Korea • Luxembourg • Malaysia • Mexico • The Netherlands • New Zealand • Norway • Peru • Philippines •
Poland • Portugal • Puerto Rico • Romania • Russia • Saudi Arabia • Scotland • Singapore • Slovakia • Slovenia • South Africa • Spain •
Sweden • Switzerland • Taiwan • Thailand • Turkey Ukraine • United Kingdom • United States • Venezuela • Vietnam • Zimbabwe
© 2007 Cisco Systems, Inc. All rights reserved.
CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of
Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo,
Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step,
Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study,
LightStream, Linksys, MeetingPlace, MGX, Networkers, Networking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way
to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0711R)

Printed in the USA

© 2007 Cisco Systems, Inc. All rights reserved.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 86 of 86