SCIENCE. SERVICE. SOLUTIONS.

WATERPROOFING ®
MiraDRAIN 6200
Description onto either side of the panels. The panels can terminate at the top of
the footing and are flexible enough to form right angles to cover the top
CCW MiraDRAIN 6200 is a high-strength drainage composite made up of
of the footing. MiraDRAIN eliminates the need for a protection course
a durable, nonwoven filter fabric that is bonded to the individual dimples
over waterproofing systems. Native soils can be used over MiraDRAIN.
of a molded polypropylene core to minimize fabric intrusion into flow
(Contact your local Carlisle Coatings & Waterproofing representative for
channels due to backfill pressure. The filter fabric prevents the passage of
specific guidelines.)
soil particles into the core while allowing water to pass freely. This product
features a polymeric sheet adhered to the back of the core to prevent it For standard installation details, follow the MiraDRAIN detail drawings.
from die-cutting the waterproofing membrane. For non-standard installation instructions contact your local CCW
representative.
Designed for use in high-flow, high-compressive strength, vertical drainage
applications where single-sided subsurface drainage is needed, MiraDRAIN Foundation Walls / Vertical Applications
6200 can also be used as a protection course over CCW waterproofing The MiraDRAIN panel can be installed in rows or columns with the fabric
membranes when added protection is desired. side toward the soil. Each method has its advantages depending on the
The flat side of MiraDRAIN 6200 fits snugly against wall surfaces, making criteria of the project as to which method is best.
this product ideal for foundation walls, retaining walls, bridge abutments, When installing the CCW MiraDRAIN in rows:
and similar structures.
1. Place the longitudinal edge of the core against the wall so that it is
flush with the wall footing.
Features and Benefits
2. Attach subsequent panels in shingle fashion with fabric overlap at
• Relieves hydrostatic pressure buildup against subterranean surfaces
bottom, placing the longitudinal edge of the upper panel over the
• Consistent, multi-directional core configuration provides a uniform flanged longitudinal edge of the lower panel and lap fabric from upper
flow path for water to escape panel over lower panel.
• High-flow drainage capacity - up to three times the flow capacity of When installing the CCW MiraDRAIN in columns:
aggregate or sand
1. Start at the low point of the wall and attach the panel to the wall.
• No-clogging drainage performance
2. Adjacent panels should be joined together with the lateral edge of the
• High-compressive-strength system withstands installation and in- connecting panel placed over the flanged edge of the previous panel.
situ earth stresses.
The fabric from the adjacent panels should overlap the preceding panel.
• Enhances waterproofing system by channeling water away and The fabric can be adhered with CCW CAV-GRIP, CCW Contact Adhesive,
providing a secondary water retention layer CCW-704 Mastic, CCW LM-800XL, Aluma-Grip 701 or duct tape. The
• Cost-saving, lightweight, easy-to-install panels eliminate the need for top or terminal edge of the MiraDRAIN should be sealed by wrapping
aggregate extra filter fabric around to the back side of the panel, and if there is
insufficient fabric, the core shall be cut out from the fabric by a depth
Installation of 3 dimples to provide excess fabric for wrapping behind the core. This
will prevent soil or other foreign construction materials from intruding
MiraDRAIN prefabricated drainage panels may be installed in a variety of
into or behind the panels. A “set back” or “ledge” condition may be
construction applications. They may be installed against retaining walls,
encountered on some construction applications. Where this condition
foundation walls (both waterproofed and non-waterproofed), lagging
exists, MiraDRAIN panels should be installed beginning at the bottom
systems and buttress/landfills. MiraDRAIN can be cut with a utility
of the wall and ending at the ledge. Subsequent courses of MIraDRAIN
knife or scissors. Slurries, shotcrete or concrete may be placed directly

Carlisle Coatings & Waterproofing

900 Hensley Lane | Wylie, TX 75098 | 800.527.7092 | www.carlisleccw.com
SCIENCE. SERVICE. SOLUTIONS.

WATERPROOFING
MiraDRAIN 6200
should be installed flat against the upper wall portion and placed so Limitations
that 4 – 6" (10 –15 cm) extend down and over the lower edge. The
Limit ultraviolet exposure by backfilling within 30 days of installation. Any
overlapping MiraDRAIN sections will be pushed flush against the wall
panels damaged during installation should be replaced by the installer.
during backfilling.
MiraDRAIN is resistant to chemicals in normal soil environments.
Attachment Method – No Waterproofing Membrane However, some reagents may affect its performance. CCW
The MiraDRAIN should be attached to non-waterproofed walls with CCW representatives should be consulted concerning the suitability of
CAV-GRIP, CCW Contact Adhesive, SecurTAPE™ tape or concrete nails. MiraDRAIN in unusual soil environments.
The MiraDRAIN will be permanently secured upon completion of backfill.
Backfill should be placed within two weeks. Backfill to atleast 6" (15 cm) Packaging
above the top edge of the MiraDRAIN. 4' x 50' (1.22 m x 15.24 m)

Attachment Method – CCW Waterproofing Membranes MiraDRAIN is made in the USA and is sold through a highly qualified sales
representative network.
The MiraDRAIN should be attached with the CCW CAV-GRIP, CCW
Contact Adhesive, or SecurTAPE. Apply CAV-GRIP over entire surface Typical Properties
of waterproofing membrane and mate the two surfaces together. The
MiraDRAIN will be permanently secured upon completion of backfill. Property Method Unit Typical Value
Backfill should be placed as soon as possible. Backfill to at least 6" (15
cm) above the top edge of the MiraDRAIN. CORE
Thickness ASTM D1777 in (mm) 0.40 (10.16)
Attachment Method – CCW MiraCLAY® Waterproofing Membrane ASTM D1621
Compressive Strength psf (kPa) 15,000 (719)
(mod)
The MiraDRAIN should be attached over the CCW MiraCLAY membrane
using fasteners compatible with substrate and 1" washers. Maximum Flow Rate ASTM D4716 gpm/ft (I/min/m) 21 gpm/ft
FABRIC (DCN04)
Attachment Method – Soldier Pile Supported Excavations Apparent Opening Size ASTM D4751 US Std Sieve (mm) 40 (0.425)
The MiraDRAIN should be secured with the appropriate fasteners for the Water Flow Rate ASTM D4491 gpm/ft 2 (I/min/m) 110 gpm/ft 2
substrate, i.e. concrete, masonry, wood or soil. Prevent concrete from Grab Tensile Strength ASTM D4632 lbs (kN) 100 (0.45)
flowing behind the MiraDRAIN core by sealing the backside of the panel Grab Elongation ASTM D4632 % 60
with a strip of CCW-705, CCW-701 or duct tape. Sealing the backside of
CBR Puncture Strength ASTM D6241 lbs (N) 250 (1113)
the panel is not necessary if CCW waterproofing membrane is applied
over the MiraDRAIN prior to pouring concrete or shotcrete. Voids in the
soil or lagging that exceed 2" (150 mm) must be filled to provide support Limited Warranty
for the MiraDRAIN. Carlisle Coatings & Waterproofing Incorporated (Carlisle) warrants this product
to be free of defects in workmanship and materials only at the time of shipment
from our factory. If any Carlisle materials prove to contain manufacturing defects
Drainage Collector/Discharge System that substantially affect their performance, Carlisle will, at its option, replace the
Collector Pipe: Place collector pipe as required in design details. For materials or refund its purchase price. This limited warranty is the only warranty
extended by Carlisle with respect to its materials. There are no other warranties,
installations where a collector pipe is specified, encapsulate the collector including the implied warranties of merchantability and fi tness for a particular
pipe in a gravel bed with a supplemental section of filter fabric as a purpose. Carlisle specifi cally disclaims liability for any incidental, consequential, or
separator/filter. other damages, including but not limited to, loss of profi ts or damages to a structure
or its contents, arising under any theory of law whatsoever. The dollar value of
Carlisle’s liability and buyer’s remedy under this limited warranty shall not exceed
the purchase price of the Carlisle material in question.

Carlisle Coatings & Waterproofing

900 Hensley Lane | Wylie, TX 75098 | 800.527.7092 | www.carlisleccw.com
02.20.20 © 20120 Carlisle. Carlisle, MiraCLAY, MiraDRAIN and SecurTAPE are trademarks of Carlisle.
REPRINT CODE: 600357 CCW-3437 - MiraDRAIN 6200 TDS