Butterfly Valves - Figure 990

Sizes 25 - 500mm

The F990 has smooth flow characteristics, abrasion,

erosion and corrosion resistance with a crevice free
internal contour.

Features
• The one-piece wafer thin disc
stem provides the very minimum
obstruction to flow.
• Rounded, polished disc edge gives
full concentric sealing, lower
torques, longer seat life and
bubble-tight shut-off.
• Wafer type split-body for easier
maintenance.
• Body locating holes provide easy
installation and a perfect centring of
the valve between the flanges.
• Primary stem sealing by preloaded
contact between flatted seat
surface and rounded polished disc
hub area exceeds the pressure
rating of the valve and prevents
leakage through shaft area to
atmosphere.
• A secondary sealing is provided by
the interference fit between shaft
and shaft hole in seat at all
positions.
• Top bushing absorbs actuator side
thrust loads.
• A moulded-in O-ring provides
flange sealing and eliminates need
for gaskets.
• The seat is field replaceable and
fully isolates the body and stem
from the flow.
• AS 2129 Table E and ANSI Class
150 end connections as standard.
Others available on request.
• The F990 is not recommended for
dead end service.
• PED approved for valves
25-300mm. General Applications
Food and beverage processing,
chemical, dry bulk conveying, paper
mills, slurry handling etc. These valves
are for any service where a bubble-
tight shut-off with maximum flow area
is required.
It has a one piece disc stem, a field
replaceable seat and a wide range of
material combinations to meet most
severe applications.

A.B.N. 83 000 922 690

© Copyright by Tyco International Ltd F990/6/02
Keystone reserves the right to change product designs and specifications without notice.
 Butterfly Valves - Figure 990
Sizes 25 - 500mm

5 Size range
25 to 500mm.
6 50 to 500mm for urethane and
ceramic trims.

3 Pressure rating
1000 kPa in 25 - 300mm S/S trims.
700 kPa in 50 - 300mm with rubber
discs, Teflon or Urethane trims.
500 kPa in 350 - 500mm for all trims.
1 350 kPa in 25 - 300mm White Buna-
N.

Temperature rating
4
Minus 40°C to 120°C with EPDM
seats.
Minus 18°C to 100°C with Buna N
seats.
Minus 15°C to 120°C with Teflon lined
Buna N seats.
Minus 30°C to 150°C with Teflon lined
2
EPDM seats.
Minus 20°C to 80°C with Urethane
seats.

Note: PED approved valves have a

temperature limitation of minus 10°C
for all seat options.

Parts List
No. Description Standard Material Material Specification

1 Upper Body Cast Iron ASTM A-126 - B

2 Lower Body Cast Iron ASTM A-126 - B
3 Disc Stem 316 Stainless Steel ASTM A743 CF8M / ASTM A-276 UNS S31600
EPDM Encapsulated Carbon Steel -
Teflon Encapsulated Carbon Steel -
Urethane Encapsulated Carbon Steel EM-D1-9
Ceramic Coated EM-D1-10
4 Seat EPDM# EM-D1-32
Buna N# EM-D1-2
Teflon - Buna N backed -
Teflon - EPDM backed -
Urethane EM-D1-9
5 Shaft Bush Acetal -
6 Shaft Seal Buna N -
7* Body Screws 304 Stainless Steel ISO 3506-1

Note:
* Body Screws not shown in illustration.
# Food grade seat.

© Copyright by Tyco International Ltd F990/6/02

Keystone reserves the right to change product designs and specifications without notice.
 Butterfly Valves - Figure 990
Sizes 25 - 500mm

A
B
D

Dimensions (mm)
Valve Stem Shaft Stem Conn. Top Plate Kv @
Size Conn. Dia. A B C D E F K Q HxG Key PCD. No. Hole Dia. Mass Full
mm Code inches inches inches mm Holes mm kg Open

25 AAA 3/8 32 62 79 29 57 19 31 15 3/8 x 1/4 44 4 6 0.7 52

40 AAA 3/8 47 82 94 30 57 19 41 36 3/8 x 1/4 44 4 6 1 120
50 BAB 9/16 52 105 140 41 102 32 70 32 9/16 x 3/8 83 4 11 3 320
65 BAB 9/16 65 117 152 44 102 32 76 48 9/16 x 3/8 83 4 11 4 430
80 BAB 9/16 78 130 159 44 102 32 88 65 9/16 x 3/8 83 4 11 5 590
100 BAC 5/8 103 162 178 51 102 32 102 90 5/8 x 7/16 83 4 11 6 960
125 BAD 3/4 129 187 191 54 102 32 119 118 3/4 x 1/2 83 4 11 8 1510
150 BAD 3/4 148 216 203 54 102 32 133 138 3/4 x 1/2 83 4 11 9 2000
200 CAE 7/8 198 271 242 64 152 32 170 188 7/8 x 5/8 127 4 14 15 3550
250 CAF 1 1/8 249 330 273 64 152 51 210 241 Ø11/8 1/4 x 1/4 127 4 14 22 5800
300 CAF 1 1/8 300 375 311 76 152 51 238 291 Ø11/8 1/4 x 1/4 127 4 14 34 8460
350 CAG 1 3/8 339 429 305 76 152 76 248 331 Ø13/8 5/16 x 5/16 127 4 14 42 9460
400 CAH 1 5/8 390 489 336 102 152 69 279 377 Ø15/8 3/8 x 3/8 127 4 14 61 12000
450 DAJ 1 7/8 441 546 368 108 203 108 314 428 Ø17/8 1/2 x 3/8 165 4 21 88 15500
500 DAJ 2 1/8 491 603 403 127 203 108 349 475 Ø17/8 1/2 x 3/8 165 4 21 112 18900
Notes:
“Q” is the disc cordal dimension at face of valve for disc clearance into pipe fittings or flange.
“H” dimension is the stem connection.
“G” dimension is across the stem flats
Kv = the flow rate of water in m3/hr that will pass through a valve with a differential pressure of 1 bar (100 kPa) @ 20°C.
Cv = 1.155Kv
Mass may vary depending on materials used.
Dimensions are nominal to ±1mm.
PED approved valve range is limited to 25 to 300mm

© Copyright by Tyco International Ltd F990/6/02

Keystone reserves the right to change product designs and specifications without notice.
 Butterfly Valves - Figure 990
Sizes 25 - 500mm

Typical Specifying Sequence

Example: 100 F990 805 AE

Valve Size Figure No. Trim Code End Connections

Valve Trims
Trim Code
Figure No. Numeric Alpha Body Disc Shaft Seat Bush Packing

F990 805 CEE2 Cast Iron 316 S/S 316 S/S EPDM Acetal Buna N
F990 723 CEE3 Cast Iron 316 S/S 316 S/S Buna N Acetal Buna N
F990 620 CEE4 Cast Iron 316 S/S 316 S/S Teflon/EPDM Acetal Buna N
F990 727 CEE5 Cast Iron 316 S/S 316 S/S Teflon/Buna N Acetal Buna N
F990 507 CEEU Cast Iron 316 S/S 316 S/S Urethane Acetal Buna N
F990 508 CUEU Cast Iron Urethane/Steel 316 S/S Urethane Acetal Buna N
F990 509 CWEU Cast Iron Ceramic ctd. 316 S/S 316 S/S Urethane Acetal Buna N
F990 398 C2E2 Cast Iron EPDM/Steel 329 S/S EPDM Acetal Buna N
F990 622 C4E4 Cast Iron Teflon/Steel 329 S/S Teflon/EPDM Acetal Buna N
F990 624 C4E4 Cast Iron Teflon/Steel 316 S/S Teflon/EPDM Acetal Buna N
F990 535 C4E5 Cast Iron Teflon/Steel 329 S/S Teflon/Buna N Acetal Buna N
#
F990 369 GEE3 Gunmetal 316 S/S 316 S/S Buna N Acetal Buna N

End Connections
• AE = AS 2129 table E
• AN = ANSI B16.5 Class 150
• Others available on request.
Note: # is not a PED approved trim option.

Available Actuators & Accessories

Figure Description
No.

F79U Aluminium Pneumatic actuators, double acting or spring return.

F79B Ductile Iron Pneumatic actuators, double acting or spring return.
F79S Stainless Steel Pneumatic actuators, double acting or spring return.
F777 Electric actuators.
F77Q Heavy Duty Electric actuators.
F791 Solenoid valves.
F792 Limit switches.
F793 Positioners.
F401 Handle Kits
F427 Gear operators.

© Copyright by Tyco International Ltd F990/6/02

Keystone reserves the right to change product designs and specifications without notice.