G Series Quick Start Guide
It is highly recommended to use the latest version of Remote Programming Software (RPS) with
the G Series Panel available from au.boschsecurity.com. You will also need a D5370–USB Key.
DEFAULT Master PIN (User 1) = 123456 To ENTER programming = CODE (123) then select [ENTER]
DEFAULT INSTALLER PIN (User 0) = 123 To EXIT programming = Hold down ESC key
PANEL BASICS
EOL: Zones:
This panel supports Single EOL = 1.0K ohm Zones on this panel are called POINTS.
in SERIES. NO SPLIT EOL Panel supports up to 599 Points.
This panel supports Dual EOL = 1.0 K ohm Main panel supports 8 x ONBOARD Points. (1 to 8)
in SERIES/1.0K ohm in PARALLEL. Panel supports up to 59 x 8 input zone expanders
Point expansion is by module or also with some other components.
Available Point Types
UNASSIGNED/Octo Input/KEYPAD/Wireless/Onboard/Output/IP Camera/DOOR
(Zonex/D8125 and POPEX components are NOT used in Australia)
A POINT also has a POINT INDEX or PROFILE of how it will work.
Up to 32 types of Point Index Profiles. Each with 34 different programmable settings.
Each Point Index number sets HOW the panel will respond when specific conditions occur on this point.
Numerous settings can be configured for each Point Index.
RF Components: RF Components and Setup:
Panel supports: RF Receiver and Repeaters
1 x B810 RADION RF Receiver
504 Points/1000 Keyfobs/supports 8 x RADION
A RADION B810 Receiver
Supports = 504 Points/1000 RF Fobs/8
RFRP Repeaters Repeaters
OR: B810 Receiver can only be enabled in RPS
SDI2 Modules/Wireless Receiver/Module Type
1 x B820 INOVONICS RF Module = B810 Radion Wireless
350 RF Points or Keyfobs/supports 8 x EN5040
Repeaters
The receiver can only be activated in programming
B INOVONICS B820 Interface Module
Supports = 350 Points or Fobs Total/8
Repeaters
via RPS
B820 Interface can only be enabled in RPS
SDI2 Modules/Wireless Receiver/Module Type
RF Fob: Add/Remove = B820 Inovonics Wireless
Users/Edit User — Select User # then [ENTER] Can only support using A or B/not both
Change User? Continue Options are:
Passcode/Name/Level/Keyfob/Card/Language Learn in/Delete RF Device
Select Keyfob Configure Keyfob? [ENTER] Point must already have Point Index and Source set
Options are: Enter ID/ADD/Replace/Remove in programming
Enter ID — Edit Enter ID # SAVE Installer/Wireless/RF Point Menu
• Enrol Point RFID ‒ Add device
ADD — Not Assigned — ADD Trigger Keyfob
• Replace Point RFID
(Learns and Saves) • Delete Point RFID
Point Index Type Point Index Type
1 24-Hr Instant on OPEN/Short 17 GAS
2 24-Hr Invisible/Short on Silent 18 GAS Supervisory
3 Pull Station 19 AUX AC Supervision
4 Smoke Detector 20 Part ON: Watch OFF
5 Smoke Detector with Verification 21 Part ON: POPIT Motion
6 Bell Supervision 22 Fire Supervisory on OP
7 Part ON: Instant 23 Non-Fire Supervisory OP
8 Part ON: Delay 24 Local Buzz on Fault
9 Part ON: Instant, Local Disarmed, Buzz 25 Part ON: Delay, Watch OFF
10 Interior: Instant 26 Part ON: Instant (2)
11 Interior: Delay 27 Part ON: Delay (2)
12 Interior: Instant, Local Disarmed 28 Interior: Follower (2)
13 Interior: Follower 29 Interior: Instant (2)
14 Maintained Key switch 30 Interior: Delay (2)
15 Momentary Key switch 31 24-Hr Instant Open/Short No Abort
16 Point Open/Close on Fault 32 Run Custom Function
Reporting: We have 4 Reporting Routes available to use.
We can use
*B430 PSTN Module Contact ID
On Board Ethernet Connetix IP
B426 SDI-2 IP Module Connetix IP
*B443 3G Cellular Module Connetix IP
*Can plug on the Main panel or plug into the B450 Module which goes on the SDI-2 BUS
Panel uses COMMAND functions for some operations. Programming
Troubleshooting Command What it Does
Command What it Does CMD 50 Move to Area
CMD 4 Silence Trouble - Clear Keypad Display CMD 51 Extend Closing Time
CMD 40 View Memory CMD 52 Change Sked Time
CMD 41 Send Test Report CMD 53 Delete User
CMD 42 Send Status Report CMD 54 Manual Operate Output ON/OFF
CMD 43 Seize Line Remote Connect RPS CMD 55 Change Passcode
CMD 44 Walk Test CMD 56 Add / Change User
CMD 45 Date and Time CMD 57 Area Text
CMD 46 Door Control Menu CMD 58 Fire Test - All Visible 24hr Points
CMD 47 Reset Sensors CMD 59 Display Panel Version - F/w Version
CMD 49 Change Display CMD 6 Watch Mode (Day Alarm) ON/OFF
CMD 0 BYPASS a Zone
CMD 00 UNBYPASS a Zone
PART ON = PERIMETER
Defaults
Point 1 24-Hr Instant on OPEN/SHORT Point 5 Type 13: Interior Follower
Point 2 24-Hr Invisible/Short on Silent Point 6 Type 7: Part ON Instant
Point 3 Pull Station Point 7 Type 7: Part ON Instant
Point 4 Smoke Detector Point 8 Type 1: 24 Hr Instant on OPEN/SHORT
Point 9 and onwards = NOT Assigned
Reporting: Change User Settings
PSTN Setup (B430 must be Installed) Users/Edit User — Select User #
Installer Code ENTER/Program/REPORTING/Phone then [ENTER]
Change User? Continue Options are:
IP (Onboard)
Installer Code ENTER/Select Ethernet then IP Module Passcode/Name/Level/Keyfob/Card/
Select either - Onboard IP Language
- Bus Module 1
- Bus Module 2 then EDIT
Select from:
Module Parameters/Address Parameters/DNS Parameters
Watch Mode ON/OFF
Points for Watch are only set in RPS
• Module Parameters DHCP Enable (default = YES) Y/N
UPnP Enable (default = YES) Y/N Menu/Settings/Watch
Area is OFF/ON? Turn ON or Off to suit.
• Address Parameters IP Address (If DHCP = N)
(default = 0.0.0.0) Enter IP Address Also done under:
Subnet Mask — Enter Subnet MENU/SHORTCUT/ scroll to
(default = 255.255.255.0) Change Watch MODE Turn ON/OFF
Default Gateway –
(default = 0.0.0.0)
Enter IP Address
Port Number (default = 7700) Add User Card: Can only be done at
Enter required if different Codepad with Reader or RPS
• DNS Parameters IPV4 Server Address (default = 0.0.0.0) Users/Edit User — Select User #
then [ENTER]
IPv6 Server Address (default = 0.0.0.0)
Change User? Continue Select CARD
Module Host Name (default = blank)
Configure Card? [ENTER]
ADD — Not Assigned — ADD
Present card for User # to Reader
(Learns and Saves)
SERVICE MODE:
ACTIVATE: Press and HOLD the RESET Button on panel for 5 seconds
Heartbeat LED: Quick Flashes Codepads say SERVICE MODE Enter Installer Code.
Options are: Install Menu/View Log/Revisions/RPS
EXIT from Service Mode: Hold RESET button 5 seconds:
Heartbeat LED will flash numerous times and panel will reset to normal after 15 seconds
Heartbeat LED returns to normal slow flashing.
Area Entry/Exit timers
Can only be set in RPS
Area wide Parameters/Area Parameters/Area #
Firmware Upgrade: Use Firmware Upgrade Wizard in RPS
Firmware Upgrade will take approx. 15 mins to complete via IP
Firmware must be downloaded and extracted (file will be an .fwr file)
Create a folder on your pc called G Series Firmware.
Firmware will be downloaded (approx. 15 mins via IP) and then Implemented to panel (approx. 2mins)
RPS will disconnect and re-connect at end of this time.
Access Control Setup Can only be setup in RPS
Needs B901 Access Module to have Door (up to 32 supported = 32 Doors) 1 module per Door
Under ACCESS Select Door Number Can change DOOR NAME text
• Select DOOR SOURCE = need to set as SDI2 (B901)
• Select Entry AREA (Area for Access) (default = 1)
• Associated Keypad # (Area selected disarms with Door) (default = 0 none)
• Door Point: Used to monitor door state
Cannot be used for any other point assignment
Must be set as PART ON point (if 1-8 remove EOL resistors)
• Auto Door: (default = N) N = Door unaffected by armed Area state
Y = Area Disarmed = Door Unlocked Armed = Locked
• FIRE Unlock: (default = N) N = Not affected Y = Unlocks with FIRE or GAS Alarm
• Disarm on Open: (default = N) N = Disarms when Valid card presented
Y = Disarm only after Door opened for access by User with Disarm Authority
• Strike Time: (default = 10 secs) 0 to 240 secs
Activates on: Valid Token/Request to Enter/REX or Cycle Door Function
• Shunt Time: (default = 10 secs) 0 to 240 secs
Amount of time Door can be opened without causing a Trouble/Alarm/Fault on
the Door Point
• Extend Time: (default = 10 secs)
Prolongs Strike/Buzz and Shunt when shunt time expires and Door still open.
At end of Extend Time buzzer continues until Door closed.
If set, point assigned DOOR indicates Trouble/Alarm/Fault at keypad.
Generates a “Trouble – Door left Open” event if Area disarmed.
•
Deactivate on OPEN: (default = Yes)
Yes = Strike deactivates when door opened on valid access granted request
No = Strike will remain activated for Strike programmed time whether door
opened or closed
• RTE Shunt Only: (default = No)
Yes = Shunt time will activate – door can be manually opened
No = RTE automatically activates the programmed Strike and Shunt time
• REX Shunt Only: (default = No)
Yes = Programmed time will activate so door can be manually opened
No = REX automatically activates programmed Strike and Shunt time
Other settings:
Access Granted Y/N (default = Y) No Entry Y/N (default = Y) Enter Request Y/N (default = N)
Exit Request Y/N (default = N) Fail Mode: Fail Safe/Fail Secure (default = SECURE)
Tamper Y/N (default=N)
Copyright © 2016 — In the interest of ongoing product improvement we reserve the right to change specifications at any time without notice — E&OE 07/16
