HCIA-Transmission V2.
0 mock exam
1. (true or faulse) Maintenance of SDH devices is easier than that of PDH devices because SDH
signals provide more overhead bytes for operation, administration and maintenance (OAM).
2. (true or faulse) If bit errors occur in the SDH network, the decapsulated service signals must
contain bit errors.
3. (true or faulse) The SDH frames are transmitted byte-by-byte from left to right, row-by-row,
and frame-by-frame.
4. (true or faulse) The 8 Mbit/s PDH signals can be multiplexed to STM-N signals.
5. (true or faulse) The data communication channel (DCC) bytes form a physical channel for
transmitting OAM information.
6. (true or faulse) Lower level alarms are often reported upon the generation of a higher level
alarm.
7. (true or faulse) WDM systems can be classified into unidirectional WDM systems and
bidirectional WDM systems based on the signal transmission directions over optical fibers. Most
WDM systems use the two-fiber unidirectional transmission mode.
8. (true or faulse) Theoretically, a multiplexer and a demultiplexer are similar and differ only in
the light output and input directions.
9. (true or faulse) ESCs are widely used in DWDM systems.
10. (true or faulse) FAS bytes in the OTUk overhead should not be scrambled. Scrambling is
implemented after the FEC portion is computed and added to an OTUk signal.
第 1 页, 共 6 页
HCIA-Transmission V2.0 mock exam
11. (true or faulse) The SM, PM, and TCMi overheads on the OTN electrical layer all contains a
one-byte BIP-8 field. The monitoring range of this field varies with the overhead.
12. (true or faulse) A VCRTUNK is an internal port of a board. It consists of several bound virtual
containers (VCs) to function as an internal transmission channel of an Ethernet board.
13. (true or faulse) The default user of U2000 is admin, which belongs to NM administrators
group. But it is higher user than other administrator users. So it is called super user. You cannot
change the authority of admin user and switch it to other group. For the security, you should
change the password of admin user and create some new users.
14. (true or faulse) When the Tag Attribute of Ethernet port is Hybrid, so it can transmit both
tagged and untagged frames.
15. (true or faulse)In the two-fiber bi-directional multiplex section protection ring, you need to
configure only services on the working channel.
16. (multiple choice) An SDH frame is composed of( ).
A. Frame header
B. Section overhead
C. Information payload
D. Administrative unit pointer
17. (multiple choice) The 2 Mbit/s signals are now most widely used. The procedures for
multiplexing the 2 Mbit/s signals to STM-N signals include ( ).
A. Rate adaptation
B. Adding pointers
C. Adding section overheads
第 2 页, 共 6 页
HCIA-Transmission V2.0 mock exam
D. Scrambling
18. (multiple choice) A WDM system is composed of( ) .
A. OTU/TU/LU
B. OM/OD
C. OA
D. OSC/ESC
E. XCS
19. (multiple choice) The correct descriptions about section monitoring (SM) bytes in the OTUk
overhead include ( ).
A. The first SM byte is a trail trace identifier (TTI).
B. The second SM byte is a bit interleaved parity-8 (BIP-8) byte.
C. The BIP-8 byte is used for ODUk-level bit error detection.
D. The third SM byte is used for the backward defect indication (BDI), backward error indication
(BEI), and incoming alignment error (IAE). It also contains reserved (RES) bits.
20. (multiple choice) Hub/Spoke (Ethernet LAN Service) is used to separate packets between the
logical ports in the network bridge. Which of the following descriptions are correct if the logical
ports are in the same VB VLAN filter or plain bridge?
A. Communication is available between ports configured with Hub.
B. Communication is available between a port configured with Spoke and a port configured with
Hub.
C. Communication is unavailable between ports both configured with Spoke.
21. (single choice) Among all the overheads in an SDH frame, the widest monitoring range is
provided by ( ).
A. Regenerator section overhead (RSOH)
B. Multiplex section overhead (MSOH)
第 3 页, 共 6 页
HCIA-Transmission V2.0 mock exam
C. Higher order path overhead
D. Lower order path overhead
22. (single choice) The byte that can be used for setting up an orderwire connection between
two regenerators is( ).
A. E1
B. E2
C. E1 and E2
D. None of the above
23. (single choice) Among the following topologies, the best protection capabilities are
provided by( ).
A. Chain topology
B. Star topology
C. Tree topology
D. Ring topology
E. Mesh topology
24. (single choice) In non-coherent DWDM system, among the following optical sources, the
highest dispersion tolerance and reliability can be provided by( ).
A. Directly modulated optical source
B. Optical source modulated by an electro-absorption modulator
C. Optical source modulated by a Mach–Zehnder interferometer
D. None of the above
25. (single choice) Which boards have a smaller noise figure and provide for a longer
transmission distance so that can substantially reduce the number of electrical regenerators?
A. OAU
B. OBU
第 4 页, 共 6 页
HCIA-Transmission V2.0 mock exam
C. RAU
D. BPA
26. (single choice) The ODUk overhead does not include ( ).
A. PM
B. TCM
C. NJO
D. APS/PCC
27. (single choice) A 2.2 m high cabinet can accommodate a maximum of ( ) OptiX OSN 3500
subracks.
A. 1
B. 2
C. 3
D. 4
28. (single choice) The timing unit of OSN equipment may work in three working modes. Which
mode means that timing unit work normally?
A. Tracing mode
B. Hold-over mode
C. Free-run mode
D. Receiving mode
29. (single choice) What is the receiver sensitivity of OSC?
A. -32dBm
B. -40dBm
C. -48dBm
D. -52dBm
第 5 页, 共 6 页
HCIA-Transmission V2.0 mock exam
30. (single choice) No alarm is returned upon( ).
A. R-LOS
B. MS-AIS
C. TU-AIS
D. HP-TIM
Answer：1.T， 2.F， 3.T， 4.F， 5.T， 6.T， 7.T， 8.T， 9.F， 10.T， 11.T， 12.T， 13.T， 14.T，
15.T， 16.BCD， 17.ABC， 18.ABCDE， 19.ABD， 20.ABC, 21.A， 22.A， 23.E， 24.C， 25.C，
26.C， 27.B， 28.A， 29.C， 30.A
第 6 页, 共 6 页
