Scribd
Upload
121 views3 pages

Noise Generated in Air Ducts

This document discusses noise generated by air flowing through ducts. It provides an empirical equation to calculate the sound power level in decibels based on air velocity and duct cross-sectional area. An example calculates that air flowing at 10 m/s in a 200mm circular duct produces 45dB of noise, while 20m/s produces 60dB. However, noise from air flow is generally negligible compared to noise from fans. Maximum gas velocities in pipes are also discussed.

Uploaded by

Mubarik Ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
121 views3 pages

Noise Generated in Air Ducts

This document discusses noise generated by air flowing through ducts. It provides an empirical equation to calculate the sound power level in decibels based on air velocity and duct cross-sectional area. An example calculates that air flowing at 10 m/s in a 200mm circular duct produces 45dB of noise, while 20m/s produces 60dB. However, noise from air flow is generally negligible compared to noise from fans. Maximum gas velocities in pipes are also discussed.

Uploaded by

Mubarik Ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Noise generated in Air Ducts

Estimate noise generated by air flow in ducts.

Air flow in ducts generates noise. The noise in the duct is determined by

 air velocity
 duct size (cross sectional area)
Generated noise can be calculated with the empirical equation

LN = 10 + 50 log (v) + 10 log (A) (1)

where

LN = sound power level in the duct (dB)

v = air velocity (m/s)

A = air duct cross sectional area (m2)

The equation modified for imperial units

LN = 10 + 50 log (vi / 197) + 10 log (Ai / 1550) (1b)

where

vi = air velocity (ft/min)

Ai = cross sectional area (in2)


 Air Ducts - Cross Sectional Areas
Example - Generated Noise in Duct by Air Flow
The cross section area of a 200 mm duct can be calculated as

A = π ((0.2 m) / 2)2)

   = 0.0314  m2

The noise generated in the duct with an air flow velocity 10 m/s can be calculated as

 LN = 10 + 50 log (10 m/s) + 10 log (0.0314 m2)

    = 45 db

The noise generated in the same 200 mm circular duct as above with air flow velocity 20
m/s can be calculated as

 LN = 10 + 50 log (20 m/s) + 10 log (π ((0.2 m) / 2)2)

    = 60 db

Note! - due to the noise generated by fans - noise generated inside ducts by air flow can in
general be neglected.

Some engineering companies restrict maximum gas velocities to 120 ft/s for any gas piping
applications. The reason provided is not only noise but a combination of factors such as:

1. Excessive Pressure Drops


2. Economic Pipe Operation
3. Life Cycle Cost
4 Noise
5. Vibration
6. Erosion / Corrosion
7. Extensive stress analysis
8. Expensive Pipe Support systems in high velocity gas lines to mitigate vibrations
9. Requirement of periodic fatigue analysis to ascertain pipe integrity in high velocity gas lines.

All these factors should be evaluated to arrive at optimum velocities for gas piping.

Sponsored Links

Related Topics

 Acoustics - Room acoustics and acoustic properties, decibel A, B and C, Noise


Rating (NR) curves, sound transmission, sound pressure, sound intensity and sound
attenuation.
 Noise and Attenuation - Noise is usually defined as unwanted sound - noise, noise
generation, silencers and attenuation in HVAC systems.
Related Documents

 Decibel - Logarithmic unit used to describe ratios of signal levels - like power or
intensity - to a reference level.
 Ducts Sizing - the Velocity Reduction Method - The velocity reduction method can
be used when sizing air ducts.
 Ductwork - Seal Classes - Ductwork air leakage classes.
 Fans - generated Noise Power - The sound generated by a fan depends on the
motor power, the volume capacity, the static pressure increase and the discharged
volume.
 Noise Attenuation in Rotary Heat Exchanges - Sound attenuation vs. frequency in
rotating heat exchangers.
 Signals - Adding Decibels - The logarithmic decibel scale is convenient when
adding signal values like sound power, pressure and others from two or more
sources.
 Velocity Classification of Ventilation Ducts - Recommended air velocities in
ventilation ducts
Sponsored Links

You might also like