ENERGIJA, EKONOMIJA, EKOLOGIJA / ENERGY, ECONOMY, ECOLOGY

Poboljšanje energetske efikasnosti industrijske gasne

peći korišćenjem sistema ponovne upotrebe toplote
Energy efficiency improvements of the industrial natural
gas furnace using a heat recovery system
Zoran Kocevski, Vlatko Cingoski, Saso Gelev

Electrotechnical faculty
University ‘Goce Delcev’ – Stip

Apstrakt - Preduzeća su snažno fokusirana na primenu različitih The potential for energy efficiency can be divided mainly into
mera energetske efikasnosti za optimizaciju postojećih two groups. Most of the measures are determined based on
elektroenergetskih sistema, kao što su motori za proizvodnju technical solutions, but several measures relate to human
električne energije, sistemi komprimovanog vazduha, osvetljenje, psychology and the inclusion of changes in the daily habits of
proizvodnja i distribucija tople vode i pare, grejanje i hlađenje, users. Most energy efficiency measures are acceptable from a
sistemi za oporavak i oporavak energije, itd. Potencijal za financial point of view and offer a relatively quick return on
energetsku efikasnost uglavnom se može podeliti u dve grupe. investment, but some are financially more intense and with a
Većina mera je određena na osnovu tehničkih rešenja, ali longer period of return of the investment.
nekoliko mera se odnosi na ljudsku psihologiju i uključivanje This project describes a combined project for improvement of
promena u svakodnevne navike korisnika. Većina mera energy efficiency based on the implementation of an energy
energetske efikasnosti je prihvatljiva sa finansijskog stanovišta i recovery system from exhaust gases on industrial furnaces,
nudi relativno brz povrat investicije, ali neke stavke su finansijski which use natural gas as primary energy fuel and automatic
intenzivnije i sa dužim periodom povratka investicije. Ovaj rad regulation and control of fan speed depending on the temperature
opisuje kombinovani projekat poboljšanja energetske efikasnosti of the product.
zasnovan na primeni sistema rekuperacije energije izduvnih The basic idea of this project is to re-use the energy from
gasova industrijske peći, koja koriste prirodni gas kao primarno exhaust gasses which was initially released freely into the
gorivo i automatskom regulacijom i kontrolom brzine ventilatora atmosphere thought chimney by the development of a new heat
u zavisnosti od temperature proizvoda. Osnovna ideja ovog recuperation system. Energy gained from the recuperation
projekta je ponovo korišćenje energije izduvnih gasova razvojem process was re-used in the same furnace as a pre-heat fresh air
novog sistema za rekuperaciju toplote koja je ranije slobodno išla improving the energy efficiency of the same furnace.
u atmosferu. Energija dobijena rekuperacijom ponovo se koristi Additionally, the authors explained the regulation and control of
kod iste peći za grejanje svežeg vazduha poboljšavajući the cooling fans with VFD speed controllers based on the online
energetsku efikasnost peći. Pored toga, autori u radu opisuju measurement of the product temperature. The implementation of
regulaciju i kontrolu ventilatora za hlađenje pomoću VFD both ideas could result in significant energy savings with an ROI
regulatora brzine na osnovu onlajn merenja temperature period of less than 1 year.
proizvoda. Implementirajući obe ideje mogli bi dobiti značajne
uštede energije sa ROI periodom manjom od godinu dana. Index Terms- Process Automation, Energy efficiency, Heat
Recuperation, Gas-fired Furnace, Motor VFD Controllers.
Ključne reči - energetska efikasnost, industrijske gasne peći,
rekuperacija toplote, vdf regulatori brzine motora I. INTRODUCTION
The term "Energy Management (EM)" was introduced in the
Abstract- Enterprises are strongly focused on the implementation 1980s. There are many definitions for it, but according to VDI
of various energy efficiency measures for optimizing their 4602, EM represents proactive, organized and systematic
existing power systems, such as power generation engines, coordination of procurement, energy conversion, transmission
compressed air systems, lighting, production and distribution of and use of energy, all to achieve demand. In doing so, the EM
hot water and steam, heating and cooling, energy recovery and considers economic objectives as well as environmental
recuperation systems, etc. objectives [1]. According to ISO50001: 2011 (E), Energy

www.savezenergeticara.org
ENERGIJA, EKONOMIJA, EKOLOGIJA / ENERGY, ECONOMY, ECOLOGY

Management is a set of interconnected or interactive elements to

determine energy policy and energy goals, as well as the
processes and procedures to achieve those goals [2].
In a nutshell, EM is a systematically organized technical tool
that enables the identification and application of measures to
reduce energy consumption and energy costs and enables the
reduction of the environmental impact of energy use. Within a
company, the typical process of EM starts with:
- analysis of the existing energy situation,
- analysis of the energy supply and production process,
- improvements in the energy utilization.
Implementation of EM is based on the P-D-C-A principle
(Plan-Do-Check-Act) [3]:
- Plan – Establish energy analysis, check major energy
indicators, goals, tasks, and take appropriate Action Figure 1 Graphic illustration of equipment layout
measures to improve energy performance adhere to the
company policies,
- Do – Implementation of EM action plans, II. IDENTIFY, RESEARCH AND COLLECT IDEA
- Check – Monitor and measure processes demonstrating A recuperation system is a device designed to reuse the heat
energy performance and comparing them with objectives generated using a heat exchanger and the cross-flow of fluids in
and policies, reporting results, and finally, ventilation and air-conditioning systems or the exhaust of
- Act – Taking actions to continuously improve energy industrial equipment. Generally, they use the heat from the
performance. exhaust gases to preheat the returning air in the process. Thus,
During analyzing energy consumption in a company, it was the recuperation system as schematically shown in Figure 2, uses
found the potential to reduce energy consumption. The company the usually wasted energy and increases the energy efficiency of
uses 4 large furnaces, each with an installed capacity of about whole systems [4].
4[MW], to heat the company’s products to a temperature of
approximately 500[°C]. The furnaces use natural gas as a
primary energy source for the burners and electricity to drive the
conveyor belt and the fans used to circulate hot air inside the
furnace. The exhaust gas temperatures of these furnaces are
above 300[°C] with the hot airflow capacity of about 4000 –
5000[m3/h], thus a significant amount of energy is wasted out in
the air through the chimney. The purpose of the project was to
examine whether this currently wasted heat from the exhaust gas
flow can be reused elsewhere as process heat. At the exit end of Figure 2 Wey of working on the recuperation process
the furnace, two fans are installed in the so-called cooling zone
each with an installed power of 22[kW]. Their purpose is to cool In many processes, a combustion process is used to obtain a
the product by circulating air down to a temperature of about certain energy-heat and the recuperation system serves to reuse
37[°C]. The furnace is divided into zones and there is a supply of some of this heat and return it to the system to improve its
fresh air in each zone and a certain amount of hot air is carried efficiency. The general rule for recuperates is to have a pressure
and combined into one channel and discharged into the drop between 150 and 250 [Pa] to avoid additional fan overload
atmosphere as waste gases through the chimney. and increased power consumption.
The idea of this project was to harness the energy of these
exhaust gases, recuperate the heat of the gasses through a heat
exchanger and return the heat as preheated fresh air at the
furnace entrance. At the secondary intake side of the heat
exchanger, the cooling zone exhaust should be used as fresh air
which does not fall below 20[°C] throughout the year.
Additionally, a non-contact infrared temperature sensor could be
installed to measure the temperature of the product. Depending
on the product’s temperature, one could adjust the fan speed in
the cooling zone, and adjust the amount of cooling air. If the
product’s temperature is less than 37[°C], the fan speed should
gradually decrease and vice versa, when the product is warm, the
fan speed will increase. Adjusting the fan speed depending on the
temperature could result in additional energy savings. Figure 3 Layout of the heat exchanger on the terrace

www.savezenergeticara.org
ENERGIJA, EKONOMIJA, EKOLOGIJA / ENERGY, ECONOMY, ECOLOGY

Table 2 Technical details of the heat exchanger

Figure 4 Installation of preheating air on the entrance of the

oven
In Figures 3 and 4 the concept of installing a recuperation
system on the exhaust production line is shown. The recuperation
system could be installed on the terrace, after the process fan and
in front of the chimney. It is envisaged to additionally install two
fans in the recuperation system which could serve to transfer
fresh air and meet the required flow and pressure. Filters could
be placed on the input sides of the primary and secondary sides.
The heat exchanger material is intended to be SS 316 due to the
corrosive environment and could be designed in such a manner to
prevent the mixing of the two media.
The heat exchanger is designed to be cassette-mounted for
inspection and regular cleaning purposes to ensure the smooth
operation of the system and reduced energy efficiency caused by The efficiency of the recuperation system could be greater,
dirt. The entire heat exchanger could be thermally insulated however, due to the limited space on the terrace and the size of
externally. To define the amount of the energy being discharged, the equipment, only 50[%] efficiency of the heat exchanger was
thus wasted through the chimneys, as well as the amount of fresh taken. The amount of energy that could be obtained was
air needed for the cooling process, the first necessary task was to calculated by the following formula:
make measurements of the airflow volume and the air 𝑄
temperatures. 𝑄 = 𝑚 ∙ 𝐶𝑝 ∙ ∆𝑡; 𝑚 = 𝜌 ∙ 𝑉; 𝑃 = ;
𝑡
where, Q is the energy, m is the mass, Cp = 1.006 [kJ/kgK], is
III. MEASUREMENT AND ANALYSIS the specific heat capacity, ρ = 1.16 [kg/m3] is the specific
The measurements of the data were done at separate measuring density, Δt = 134.5 [°C], V = 5000 [Nm3/h] is the volume of the
points; inserts in the fresh airline and the furnace exhaust line, airflow within the furnace, and P is the total power.
using portable flow and temperature measuring instrument Due to the uninterrupted working process, the total number of
KURZ 4222, shown in Figure 5. working hours and the total amount of heat could be calculated
as:
- The total number of working hours:
365·24 = 8760[hours/year],
- The total amount of heat:
Q = P·t = 217·8760 = 1,900[MWh].
Initial calculations showed that this recuperation process has
Figure 5 Instrument for airflow measurements Kurz 4222 a large potential for energy savings that amount to 217[kW/h], or
in total, approximately 1900[MWh/year]. Part of the waste gas
Five consecutive measurements at different positions of the energy through a heat exchanger is returned to the same furnace
channels were made and the average value of the obtained results as preheated air at the inlet of the furnace on the fresh airside.
was taken in the analysis. Figures 3 and 4, show the locations where the heat exchanger
could be installed, the recirculated hot air inlet in the furnace and
Table 1 Average value of temperature and airflow in the furnace the cooling zone exhaust duct which will serve to provide stable
year-round temperatures.
Airflow Temperature
[Nm3/h] [°C]
Exhaust - Oven output 5000 300
Furnace Fresh Air -
5000 35
Furnace Entry

www.savezenergeticara.org
ENERGIJA, EKONOMIJA, EKOLOGIJA / ENERGY, ECONOMY, ECOLOGY

algorithm is based on a certain condition, in this case, the

temperature of the product. The statement (If – then), is used
with: if (condition) – then (action) [5].
The temperature of the final product is variable in size
depending on the size of the section, its heat, the outside
temperature as well as the velocity of airflow to cool the section
and it depends on the fan speed. As mentioned above, the
product is preheated to about 500[°C], and then cooled in the so-
called cooling zone utilizing two 22[kW] fans. One fan is used to
inject fresh air and the other to remove hot air from the cooling
zone, heated by subtracting the temperature from the parts. Fan
motors are powered by VFDs (Variable Frequency Drives) for
online control and regulation of the speed of the motor, i.e. the
fan. They usually work in dual mode, winter and summer, and
most of the time they work faster than the optimum speed.
An infrared non-contact temperature sensor Micro epsilon
CTF SF15 is selected for temperature measurement (Figure 7).
Figure 6 Heat exchanger cross-section
This model is chosen because it has a very short measurement
Figure 6 shows a cross-section of the proposed recuperation time of 150[ms].
system. It has filters on sides, the fresh airside and the returns
airside. Inside is an air-to-air crossover heat exchanger. Two fans
should be fitted on the inlet and outlet side which could be
powered by high-speed regulators and will provide a
continuously identical flow of air in order not to cause a pressure
imbalance inside the furnace. This could be achieved by
installing an airflow meter in the ducts that could provide
information data for the regulation of the fan speed.
Table 2 shows the recuperation system calculations data. The Figure 7 Infrared temperature sensors
recuperation system power in summer operating conditions is The shortest measurement time is required due to the specific
217[kW], with an output useful air temperature of 165.5 [°C] and installation space. The temperature infrared sensor is positioned
a flow rate of 5000 [m3/h]. With these characteristics, the energy in a narrow slot between two moving lanes along which the
efficiency ratio would be 49.1[%]. The energy efficiency of the product moves. The elapsed time in the measuring space is
heat exchanger is conditioned by its size and the installation longer than the sensitivity and speed of the temperature gauge
conditions. and is enough to obtain useful and accurate values. The product
Every automated control system has two parts – execution of must be measured at the bottom since that part is the warmest
the process and control of the process. The control system is and is used as the reference value for its temperature.
required to receive information, the logic algorithm to process The temperature sensor has an analog output of 4-20[mA] and
the data, and to issue executable commands to the devices. This is connected to the AI (analog input) of the PLC. An appropriate
process needs to be repeated cyclically. Automated control algorithm regulates the speed of both motors with a nominal
systems are composed of several inherently different subsystems power of 22[kW] each, powered by VFDs. The temperature
(e.g. electrical, mechanical, and hydraulic) that are reading was in the range between 0 – 100[°C]. Any other
interconnected properly to accomplish a given function of the readings were considered invalid. In that case, the motor speed
system. There are three basic types of control system: regulation was kept fixed, as predefined. Obtaining data from the
- an open-loop control system, temperature section is discretionary at a precise time. For this
- a closed-loop control system, (system with the feedback), purpose, a detection sensor was installed and at the same time,
- control system based on the principle of compensation. the temperature gauge measures the product. This avoids
Principle of feedback – closed-loop control is formed as a misreading the ambient temperature without the product being
function of the deviation i.e. error between the output parameters present. The system analyzes twelve successive products and
and the specified goal. This control system is widely used and takes the mean temperature value of the two warmest products.
will be used in this project as well. Additionally, these control The preset temperature was 35[°C] with an acceptable
systems can be continuous and discrete. In continuous systems, temperature discrepancy range between 32[°C] and 37[°C]. If
variables are monitored over time and discrete variables are the average temperature was lower than 32[°C], the fan speed
monitored only at certain intervals, depending on the needs and would decrease by 2[Hz] (maximum up to 20 [Hz]). If the
process. We will look at a stochastic system in which we cannot temperature was above 37[°C], the fan speed would increase by
predict the output characteristics. Practically, by changing the 10[Hz]. The maximum speed was limited to the original set for
input and output parameters, we will define a probability that section. If the temperature of the product was within the
distribution. In this project, we use sequential control. The logic range between 32[°C] and 37[°C], the fan speed would not

www.savezenergeticara.org
ENERGIJA, EKONOMIJA, EKOLOGIJA / ENERGY, ECONOMY, ECOLOGY

change. If the temperature rises above 45[°C], the SCADA alarm Controlling the fan speed was done in accordance with the
occurs and the process and furnace stopped. following basic equitation:
The setting of the fan speed is defined by the recipe and
depends on the working product. When changing the product, the 1. Airflow is proportional to the speed:
logic starts from the beginning of processes and the fans rotate at 𝑉2 𝑈2
=
a higher speed. This is done to avoid the possibility of 𝑉1 𝑈1
overheating the products with the previously set data for the
previous process and/or product. Before practically 2. The air pressure is proportional to the velocity squared:
implementing this logic, a test was performed with manual 𝑈2 2
adjustment of the fan speed and constant monitoring of the 𝑝2 = 𝑝1 ∙ ( )
𝑈1
temperatures of products.
3. The ventilation power is proportional to the velocity
cubed:
𝑈2 3
𝑃2 = 𝑃1 ∙ ( )
𝑈1

The electric power is calculated from the mechanical power of

the motor:
𝑃𝑒𝑙 = 𝑃𝑚𝑒ℎ /

where, Pel is the electrical power of the motor, Pmeh is the

mechanical power of the engine, while  is the efficiency
coefficient of the motor.
By applying the obtained formulas, the choice of power and
power output when applying a fan speed is expressed in [%] of
Figure 8 Graphical explanation of recorded temperature of the
the maximum capability. Total energy savings in nine months
product
(not applicable in summer) if fans worked with the reduced speed
Figure 8 shows the trend of recorded temperature change of down to 60[%] amounts 146[MWh].
the measured products during one day in May. As shown, the Figure 10 also shows a graph derived from fan speed control
temperature changes from 27[°C] to 42[°C], while the fan speed calculations showing the dependence of the amount of energy
was at maximum. This indicates that the automatic temperature required for nine months of operation and the fan speed. By
regulation is achievable with reducing the fan speed at night reducing the fan speed down to 50[%], its power consumption
and/or throughout the day as the production process requires was only 1/8 of the energy consumed at top speed.
cooling of parts with ambient air temperature below 30[°C].
During the test, it was observed that the temperature of the
products could be slightly increased by shifting the speed
gradually or halving, based on the measured temperature of the IV. ECONOMICA BENEFITS OF THE PROJECT
products coming out of the furnace (see Figure 9).
We presented the technical solution and technical benefits that
the proposed project could achieve in the process of
Fan speed vs part temperature improvements in the energy efficiency of the production process.
However, to be applicable, we also had to investigate its
economic benefits in terms of investment cost, energy savings,
and investment rate of return. This data is provided in Tables 3
100 and 4.
90
80 As shown in Table 3, the installation of 217[kW] heat
70
60 exchanger for the continuous production process of 8760
50 hours/year contributes to a significant annual energy savings of
27 28 30 31 33 34 1,900[MWh] or financial benefit of approximately 81,709
Euro/year. For the estimated total investment cost of
1 2 3 4 5 6
approximately 60,000 Euro, the return of the investment is very
Fan speed % 100 90 80 70 60 50 favorable, and even including modest banking interest rates, it is
Part temperature C 27 28 30 31 33 34 less than one year.

Figure 9 Ratio between product temperature and fan speed

www.savezenergeticara.org
ENERGIJA, EKONOMIJA, EKOLOGIJA / ENERGY, ECONOMY, ECOLOGY

V. CONCLUSIONS
Fan speed vs Energy spend
The high energy savings and rapid return on investment indicate
the realization of this project. The full realization of the proposed
319 project would additionally lead to reducing CO2 emissions. The
potential of saving energy and money is twofold; first, due to
232 additional installation of heat exchanger and heat recuperation
163 the energy of the waste gas returned back to the same furnace as
preheated air at the inlet of the furnace, and second, by regulating
100 90 80 70110 6069 5040
the amount of cooling air for cooling the products using fan
1 2 3 4 5 6 speed regulator based on utilization of VFDs. The economic
Fan speed % analysis shows that the rate of return of the investment is less
100 90 80 70 60 50
than one year which is very favorable for this and any other
Energy spend in 9 similar production process. After full implementation of the
319 232 163 110 69 40
month (MWh) proposed project on the first furnace and proving the expected
results and benefits, the same procedure is scheduled to be
Figure 10 Ratio between energy and fan speed repeated at the second furnace.
Table 3 Analysis of energy-saving and return of REFERENCES
investments [1] VDI 4602,
Heat Exchanger power [kW] 217 [2] DIN EN ISO 50001
Yearly energy savings [MWh] 1,900 [3] Wikipedia,- https://en.wikipedia.org/wiki/Energy_management
Yearly savings [Euro] 81,709 [4] Heat recovery system
http://www.soloheatinginstallations.co.uk/heat_recovery.htm
The investment [Euro] 60,000
[5] S.Gelev ,”Дигитални системи на управување” , ” Goce Delcev”
Return on investment ROI [years] 0,7 University, Stip, North Macedonia, 2016, ISBN: 978-608-244-341-6.

Fan speed regulation additionally contributes to the AUTHORS

improvement of the energy efficiency of the whole production
process. Using VFDs fans with regulated speed leads to annual First Author –Zoran Kocevski, Electrotechnical engineer,
energy savings of approximately 146[MWh], or in cash annually [email protected]
savings of 14,200 Euro. The total investment for this equipment Second Author – Prof. D-r Vlatko Cingoski, professor, Faculty
is estimated at 2,400 Euro, thus the return on investment of Electrical Engineering,” Goce Delcev” University, Stip, North
including interest rates and all costs could be 0.2 years. Macedonia, [email protected].
Third Author – Prof. D-r Saso Gelev, professor, Faculty of
Table 4 Analysis of energy-saving and return of investments Electrical Engineering,” Goce Delcev” University, Stip, North
Macedonia, [email protected]
Yearly energy savings [MWh] 146
Yearly savings [Euro] 14200 Correspondence Author – Prof. D-r Vlatko Cingoski, professor,
The investment [Euro] 2400 Faculty of Electrical Engineering,” Goce Delcev” University,
Return on investment ROI [years] 0.2 Stip, North Macedonia, [email protected].

www.savezenergeticara.org