Technical Bulletin UTAX CD 1118

UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 01 / KEY COUNTER Part number

SB-8905/M
Date: 26-10-2009

TOPIC:
The part number of the key counter and the installation parts.

No. 1 No. 2

No. 3

Old Part New Part Q’ ty Compatibility

No No. No. Description
Old New Old New SP
1 ---------- 2A369708 SET PARTS KEYCOUNTER NEW COLOR - 1 - O -
2 ---------- 2KK94590 PARTS WIRE KEY COUNTER SET - 1 - O -
3 ---------- 82142540 KEY COUNTER - 1 - O -
Parts with “O” indicates regular maintenance parts. "+" Mark at the head of the description means it is a components parts.

1/1
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 02 / Firmware Upgrade (I)

SB-8973/M
Date: 29-10-2009

Only J CD 1218, CD 1222 / DC 2218, DC 2222

TOPIC:
The firmware was upgraded as follows.

Content of Changes

No. Content Details CTL FW

1 Measures against “Memory full” was displayed if the Start key was pressed for scanning job after 390627 MAIN
JAM05 changing the function to (Copy) screen and setting original to the DP when
memory was nearly full. Then, if the function was changed to (Scan) and
returned to (Copy), “Memory full”, “Continue?” and “Cancel?” were displayed.
If “Continue” was selected, JAM05 occurred. Therefore, the following change
was made.
<Change>
Change of functions is prohibited when memory full is displayed.
2 Measures against Once changing to (Send) screen and sending data to PC when paper cassette 396067 MAIN

abnormal image when became empty during printing, abnormal image might be printed if copy was
paper cassette resumed by refilling papers. Therefore, this was corrected.
became empty during
printing
Example of
abnormal image

Paper feeding
direction

1/2
 Only J CD 1218, CD 1222 / DC 2218, DC 2222

Type Program No. Check SUM Ver. Remarks

MAIN (IPU) 2KH_2000. 001.030 ---- 001.030 Å New Upgrade

ENGINE 2KK_1000. 002.002 ---- 002.002

LANGUAGE E 2KH_81XE. 001.003 ---- 001.003
PRINTER FS 2KH_3F00. 001.022 ---- 001.022
When upgrading firmware or replacing a board, please upgrade each of the firmware (MAIN, ENGINE, LANGUAGE, etc.) to
the latest version at the same time.

Classification Entire Stock Rework In-Field modification at next visit

In-Field modification by case No modification necessary
Field Measure: Please upgrade the firmware to the latest version when the phenomenon described
above arises.
Serial Nos. of Affected Machine: CD 1218 / DC 2218 J QQM9800178
CD 1222 / DC 2222 J From the August, 2009 production*

* The above is the plan at the present moment. / Please note that this is subject to change.

2/2
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 03 / Print System Z - Firmware Upgrade

SB-9052/M
Date: 11-11-2009

Only J CD 1118 / DC 2118

TOPIC:
The firmware was upgraded as follows.

Content of Changes

No. Content Details CTL FW

1 Measures against lock- The toner information detected while data was received during sleep mode 396921 PRI
up after sleep mode could not be processed and the data was not output wile “Waiting” was
displayed. Therefore, this was corrected.
2 New flash memory Change was made in order to support the flash memory of Numonyx which will PRI
device be used in the future.

Only J Print System Z (CD 1118 / DC 2118)

Type Program No. Check SUM Ver. Remarks

PRINTER 2KK_3000.000.020USB ---- 2KK_3000.000.020 For PC/USB ÅNew Upgrade

Classification Entire Stock Rework In-Field modification at next visit

In-Field modification by case No modification necessary
Field Measure: Please upgrade the firmware to the latest version when the phenomenon described
above arises.
Serial Nos. of Affected Machine: To be informed later *

* The above is the plan at the present moment. / Please note that this is subject to change.

1/1
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 04 / Firmware Upgrade
SB-9250/M
Date: 11-01-2010

Only J CD 1218, CD 1222 / DC 2218, DC 2222

TOPIC:
The firmware was upgraded as follows.

Content of Changes

No. Content Details CTL FW

1 Measures against the The original on the DP may not be detected and not be fed from the DP, but the 423847 MAIN
failure to detect the platen may be scanned to copy in case copy is started with <Start> button when
copying original on the restarting from sleep mode. This is corrected.
DP
- This does not occur in case of restart from sleep by print job and manual
restart.
- This does not occur in FAX mode.
- This can be reset by power off/on.

<Change>
The DP connection information may be cleared (initialized) when restarting from
sleep mode. Therefore, the step to check the DP connection is added.

Only J CD 1218, CD 1222 / DC 2218, DC 2222)

Type Program No. Check SUM Ver. Remarks

MAIN (IPU) 2KH_2000.001.040 ---- 001.040 <-- New Upgrade

ENGINE 2KK_1000.004.001 ---- 004.001
LANGUAGE E 2KH_81XE.001.003 ---- 001.003
PRINTER FS 2KH_3F00.002.002 ---- 002.002
When upgrading firmware or replacing board etc., please upgrade each firmware (MAIN, ENGINE, LANGUAGE) to the latest
version at the same time.

1/2
Classification Entire Stock Rework In-Field modification at next visit
In-Field modification by case No modification necessary
Field Measure: Please upgrade the firmware to the latest version when the phenomenon described
above arises.
Serial Nos. of Affected Machine: From the production in December, 2009 on*

* The above is the plan at the present moment. / Please note that this is subject to change.

2/2
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 05 / Change of the torque limiter (paper feed section)

SB-9144/M
Date: 13-01-2010

TOPIC:
The torque limiter (No.1) is changed as below for preventing the abnormal noise.
According to the change, attention is required when replacing the torque limiter (No.1) at the paper feed
section (the paper feed section of the main machine or PF-420) and please refer to <Field Measure> below.

CONTENT OF CHANGES:

The torque limiter (No.1) and the shaft (No.2) in the paper feed section

B
Before After
Old No.1: 14mm parts as New No.1: 18mm parts as
external diameter external diameter

X
X
A
New No.2: Length of X section is 6.3mm
Old No.2 (Extended by 2mm toward the torque
: Length of X section is 4.3mm limiter.)

* Convex sections (X) are in two places of both sides of the shaft.

Matching condition: view from A of above figure Matching condition: view from B of above figure

X
* Convex section (X) of the old shaft (No.2) matches to * Convex section (X) of the new shaft (No.2) matches to
the U-shape notch section of the old torque limiter the bump at the inside diameter of the new torque limiter
(No.1). (No.1).

1/2
 1) The insulation External diameter of the torque limiter (No.1) in the paper feed and the drive section is
changed from 14mm to 18mm.
2) Size of the convex section (X below) of the side of the shaft (No.2) that matches with the torque limiter
(No.1) at the paper feed section (the paper feed section of the main machine or PF-420) is extended by
2mm because the shape of the torque limiter (No.1) that receives convex section of the shaft (No.2) is
changed according to the above change 1).
3) According to the above change 1), 2), the assembly of the new torque limiter section (No.3) is registered
as the service parts to improve exchange of the torque limiter and the shaft in the paper feed section in
the field.

PARTS RETARD ASSY SP (NO.3)

The components of the assembly of the Torque limiter section

-TORQUE LIMITER 340 (No1)

-SHAFT RETARD (No2)
-PULLEY (Pt/No.: 2AR07230)
-HOLDER (Pt/No.: 2C907250)

Old Part New Part Q’ ty Compatibility

No No. No. Description Remarks
Old New Old New SP
1 2KK06050 2C907280 TORQUE LIMITER 340 *1 *1 X* X* -
2 2KK06080 2C907300 SHAFT RETARD 1 1 X X -
3 ------------ 2KK94700 PARTS RETARD ASSY SP - 1 - O O *2 / *3
Parts with “O” indicates regular maintenance parts. "+" Mark at the head of the description means it is a components parts.

* At the paper feed section or PF 420, please use the set of the old parts or new parts that is combination of 1pce of the
torque limiter (No.1) and the shaft (No.2).
In 1pce of the torque limiter (No.1) at the drive section, no particular problem is expected.
*1: CD 1118, CD 1218, CD 1222 / DC 2118, DC 2218, DC 2222: 2pcs (each 1pce is used at the paper feed/drive section),
PF 420: 1pce
*2: Service Parts
*3: It is supply in the state to assemble the new torque limiter (No.1) at the paper feed section, the new shaft (No.2), and the
pulley (2AR07230), the holder (2C907250) that fixed to the shaft.

Classification Entire Stock Rework In-Field modification at next visit

In-Field modification by case No modification necessary
Field Measure: Please use the set of the old parts or new parts when replacing the torque limiter (No.1) or
the shaft (No.2) in the paper feed section of the main machine or PF-420 because the old
and new shape for matching is different.
(In the torque limiter (No.1) at the drive section, no particular problem is expected.)

Serial Nos. of Affected Machine: CD 1118 / DC 2118 J From next production

CD 1218 / DC 2218 J QQM9Y00561
CD 1222 / DC 2222 J From next production
PF 420 / PF 420 J From next production

2/2
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 06 / Fax System R – function keys failure

SB-A011/M
Date: 04-02-2010

Only J CD 1218, CD 1222 / DC 2218, DC 2222

TOPIC:
The operation board (Figure B below) may not detect switching of the cover plate when laying the cover plate
(Figure A below) to left.

CAUSE:
In case the operation board (B) warps upward toward the direction (X) due to variation of parts and the gap
between the bottom face of the cover plate sensor switch inside KEY FAX (No.2) and the leading edge of the
sensor switch on the operation board is large,
the bottom face of the cover plate that is depressed when the cover plate is laid to left, does not enough push
the leading edge of the sensor switch on the operation board and switching the cover plate is not detected.

FIELD MEASURE:

In order to securely depress the sensor switch (D) on the operation board, a Lumirror sheet (No.3: 3X10mm
t=0.275mm) is applied to the sensor face on the cover plate sensor switch (C) to increase pushing distance.

PRODUCTION MEASURE:

A convex (t=0.3mm) is added to the sensor face on the cover plate sensor switch (C) inside KEY FAX (No.2) to
extend the detecting stroke.

1/3
 A: Cover plate
A B: Operation board
C: Cover plate sensor switch
(part inside KEY FAX(No.2))
D: Sensor switch

<Cross-section view of cover plate switch>

(View toward Z)
Z (Cover plate laid to right) A
C
C
No.6 Y
D
D
B

X Going down
(warpage upward)
(warpage)

*In case the operation board (B) warps upward and

the switch (D) goes down, the gap (Y) may be large
between the bottom face of the switch of KEY FAX
(C) and the leading edge of the switch (D)

Operation unit when installing the FAX SYSTEM R (Option)

(Cover plate laid to right)

Cover plate detection switch (C)

Laid to left

Cover plate
laid to left

Tab
One touch key and function keys when KEY FAX is correctly detected
(Cover plate laid to right) One touch key: #1 to #20
Function key: Memory TX, ON-hook, Pause/Redial, Abbreviation/Directory
(Cover plate laid to left) One touch key: #21 to #32, etc.
Function key: Register, TAD/Manual TX, Status, Print report, Duplex TX,
Polling, Delayed TX, Sub address, Broadcast, Confidential, Check
current status
*The operation board may not detect the cover plate (A) is laid to left and incorrectly detect it laid to right.
(e.g. Attempting to press Register key is detected as Memory TX)

2/3
Field measure Align to edge
0mm
<Cross-section view of cover plate detection>
0mm 0.5mm
Align to bump
A
1mm

Lumirror sheet (No.3)

Lumirror sheet (No.7) 3x10mm
t=0.275mm
(incl. couple-face
C tape)

Cover plate (A)

*Switch (C) is pushed more with thickness of the
Lumirror sheet (No.3) when the cover plate is laid to left
Measure at production

<New cover plate detection switch(C)>

Convex (t=0.3mm) added

No.2

Old Part New Part Q’ ty Compatibility

No No. No. Description Remarks
Old New Old New SP
1 2KH94220 2KH94221 PARTS OPE ASSY(E) 1 1 X O O
2 2KH94140 2KH94141 +PARTS KEY FAX SP 1 1 X O O
3 ------------ 3MZ05310 SHEET SPACER - 1 - O - *1
Parts with “O” indicates regular maintenance parts. "+" Mark at the head of the description means it is a components parts.
*1: Service Part for field measure

Classification Entire Stock Rework In-Field modification at next visit

In-Field modification by case No modification necessary
Field Measure: Please affix the Lumirror sheet (No.3) to the sensor face on the cover plate sensor switch (C)
for the cover plate (A) after cleaning it with alcohol when the above phenomenon arises
Serial Nos. of Affected Machine: From the production in January, 2010 on

3/3
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 07 / Firmware Upgrade
SB-A034/M
Date: 21-04-2010

TOPIC:
Stopping the LSU drive while waiting JOB

CONTENT OF CHANGES:

No. Contents Remarks CTL FW

1 Stopping the LSU drive The user may feel the LSU drive noisy if it is left for a long time because the LSU 430724 MAIN
while waiting JOB keeps rotating while waiting JOB. 429214
This is changed to stop the LSU drive in the following condition.

<Content of change>
1. In case JOB is not executed
--- The LSU drive is stopped when either the following continues for ten
seconds.
- The original is set at the DP - DP jam occurs
2. In case JOB is waiting
--- The LSU drive is stopped when either of the following continues for thirty
seconds.
- The error occurs while executing the Copy Job or the Print Job or the Fax Job.
Copy: <Copy mode error> is displayed at the operation panel in the
Command Center.
Print : <Print mode error> is displayed at the Copy screen.
Fax : <FAX mode error> is displayed at the Copy screen.
- The Scan screen is displayed. - Fax is sent.
- Network Fax is received or sent. - The service call error occurs.
2 Measure against the Normally, the power is turned off when the display of LCD disappears after the 429634 MAIN
LCD horizontal line main switch is turned off.
(Only for However, the horizontal thin line may remain in the LCD if the power is turned off
CD 1218, CD 1222 / before the LCD turning off.
DC 2218, DC 2222 ) This is corrected. (The LCD tuning off is most prioritized.)

1/2
 FIRMWARE CD 1118 / DC 2118
Type Program No. Check SUM VER. Remarks
MAIN ---- ---- 2KK_2000.001.027 only DIMM (No.1) New
ENGINE ---- ---- 2KK_1000.004.001 only DIMM (No.1)
LANGUAGE ---- ---- 2KK_8100.001.007 only DIMM (No.1)
Separate firmware of MAIN, ENGINE and LANGUAGE is not supplied.

Old Part New Part Q’ty Compatibility

No. Description SP Remarks
No. No.
Old New Old New
PARTS DIMM PWB ASSY
1 2KK94580 2KK94583 - 1 - O O CD 1118 / DC 2118
WITH SOFTWARE
Parts with “O” indicates regular maintenance parts.

FIRMWARE CD 1218, CD 1222 / DC 2218, DC 2222

Type Program No. Check SUM VER. Remarks
MAIN (IPU) 2KH_2000.001.042 ---- 001.042 New
ENGINE 2KK_1000.004.001 ---- 004.001
LANGUAGE E 2KH_81XE.001.003 ---- 001.003
PRINTER FS 2KH_3F00.002.002 ---- 002.002

When upgrading firmware or replacing board etc., please upgrade each firmware (MAIN, ENGINE, LANGUAGE, PRINTER)
to the latest version at the same time.

Classification Entire Stock Rework In-Field modification at next visit

In-Field modification by case No modification necessary
Field Measure: Please upgrade the firmware to the latest version when the phenomenon described
above arises.
Serial Nos. of Affected Machine: From the production in March, 2009 on*

* The above is the plan at the present moment. / Please note that this is subject to change.

2/2
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 08 / Note when replacing the SCANNER WIRE

SB-A184/M
Date: 16-06-2010

TOPIC:
WIRE SCANNER BLACK/GRAY (No.1, 2) are changed as below to improve the procurement.
Accordingly, marking to the terminal is changed from black to red.
And, an attention is required when replacing the parts according to this change.
Please refer to Field Measure as below.

Wire type: (Before) EC75-100R2 --> (After) WS77-100

Outer diameter (Before resin coating*): (Before) 0.75mm --> (After) 0.77mm
Strand diameter: (Before) 0.05mm --> (After) 0.07mm
Number of strand: (Before) 133 --> (After) 75

* New outer diameter after resin coating is same as the old one.

MARKING TO THE TERMINAL:

(The marking is applied to the side that faces SHAFT DRIVE when fitting the wire to DRUM PULLEY)

Before After

Old Part New Part Q’ty Compatibility

No. Description SP Remarks
No. No.
Old New Old New

1 2C912350 2KK17540 WIRE SCANNER BLACK 1 1 X X - Machine rear side

2 2C912360 2KK17550 WIRE SCANNER GRAY 1 1 X X - Machine front side

Parts with “O” indicates regular maintenance parts. The above-mentioned parts are not set as the spare parts in the Parts List.

Classification Entire Stock Rework In-Field modification at next visit

In-Field modification by case No modification necessary
Field Measure: Please use either set of the new parts (No.1, 2) or the old when replacing the wires.
Serial Nos. of Affected Machine: After using up the old stock.

1/1
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 09 / Error in the fuser section (C6000 / C6050)

SB-A182/M
Date: 17-06-2010

TOPIC:
The sub heater or the main heater in the fuser unit may be broken when the following service call error appears.
If only either of the heaters is broken, the machine becomes usable because the service call error is reset by
operation condition or environment.
C6000 J Fuser heater break
C6050 J Abnormally low fuser thermistor temperature
Please execute the following contents because it becomes cause of reoccurring the service call error (or the
fusing failure) if using continuously with the heater broken.

CHECK:
Please check the conductivity of each of the heaters by the tester for confirming the condition of the connection.
And, please surely replace the fuser unit or the heater if it is checked that the heater is broken.
Please check the conductivity of the heater each and the fastener terminal that is connected to the right side of
the thermostat as in the photo 2.
Check of the conductivity of the heater
Below is the state that the fuser unit is installed into the machine
Photo 2
Photo 1

Main heater

Sub heater

Sub heater side Main heater side

Classification Entire Stock Rework In-Field modification at next visit

In-Field modification by case No modification necessary
Field Measure: Please check and execute the measures according to the above procedures because the
main heater or the sub heater in the fuser unit may be broken when the above service call error (or the fusing
failure) appears.
Serial Nos. of Affected Machine: --------

1/1
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 10 / Change of the torque limiter (paper feed section)

SB-A231/M
Date: 29-07-2010

TOPIC:
Following are changed for procurement ease after the torque limiter (No.2) and the shaft (No.3) at the paper feed
section were changed to prevent the abnormal noise as informed per the Technical Bulletin TB-05.
Accordingly, attention is required when replacing the torque limiter (No.2) at the paper feed section (the paper feed
section of the main machine or PF-420). Please refer to [Field Measure] as below.

CONTENTS OF CHANGE:

External diameter of the torque limiter (No.2) at the paper feed section is changed from 18mm to 14mm. And, the
claw at the internal diameter of the housing of the new torque limiter (No.2) is changed to 4 positions, the color of
the housing is changed from black to white.
Size of the convex section (X in the figure below) at the side of the shaft (No.3) that matches the torque limiter
(No.2) at the paper feed section (the paper feed section of the main machine or PF-420) is reduced by 2mm
because the shape of the torque limiter (No.2) that receives convex section (X) at the shaft (No.3) is changed
according to the above change 1). According to the above change 1), the torque limiter (No.4: It is same as the
torque limiter at the paper feed section before the last change) at the drive section is also changed. (Its claw is 4
positions and the color of its housing is white.)

The torque limiter (No.2) and the shaft at the paper feed section
(Only the torque limiter (No.4) is individually changed at the drive section of the main machine.)
A
Before After

Old No.2: Ø18mm New No.2: Ø14mm

X
X
B
New No.3: length of X is 4.3mm
Old No.3: length of X is 6.3mm

* Convex sections (X) are in two places of both sides of the shaft.

(Matching condition: view from A of above figure) (Matching condition: view from B of above figure)
X

X
* Convex section (X) at the old shaft (No.3) matches to * Convex section (X) at the new shaft (No.3) matches to
the bump at the inside diameter of the old torque the U-shape notch section of the new torque limiter
limiter (No.2). (No.2).

1/3
 Old Part New Part Q’ty Compatibility
No. Description SP Remarks
No. No.
Old New Old New

1 2KK94700 2KK94701 PARTS RETARD ASSY SP 1 1 O O O *1

2 2C907280 2KK06051 +TORQUE LIMITER 340 1 1 X* X* - *2

3 2C907300 2KK06080 +SHAFT RETARD 1 1 X X -

Torque limiter at the
4 2KK06050 2KK06051 TORQUE LIMITER 340 1 1 O O -drive section
Parts with “O” indicates regular maintenance parts. "+" Mark at the head of the description means it is a components parts.
* At the paper feed section of the main machine or PF-420, please use the set of the old parts or new parts that is
combination of 1pce of the torque limiter (No.2) and the shaft (No.3).
*1: It is supply in the state to assemble the new torque limiter (No.1) at the paper feed section, the new shaft (No.2), and the
pulley (2AR0723_), the holder (2C90725_) that fixed to the shaft.
*2: CD 1118, CD 1218 / DC 2118, DC 2218: 1 pce, CDC 1222, DC 2222: 2pcs (each 1pce is used at the paper feed section
of the two cassettes), PF 420: 1pce

Classification Entire Stock Rework In-Field modification at next visit

In-Field modification by case No modification necessary
Field Measure: Please use the set of the old parts or new parts when replacing the torque limiter (No.2) or
the shaft (No.3) at the paper feed section of the main machine or PF-420 because the old
and new shape for matching is different.

However, the new No.2, 3 can be individually fitted for the machine before the Technical
Bulletin TB-05.

(*) Please refer to the next page for change history of the torque limiter and the shaft at the
paper feed section, the parts that can be used

And both of new and old torque limiter (No.4) at the drive section can be used.
Serial Nos. of Affected Machine: CD 1118 / DC 2118 J from the production in September, 2010 on.
CD 1218 / DC 2218 J from the production in September, 2010 on.
CD 1222 / DC 2222 J from the production in September, 2010 on.
PF 420 / PF 420 J from the production in September, 2010 on.

2/3
Change history of the torque limiter and the shaft at the paper feed section

Technical Bulletin TB-05 This change

Torque limiter: 2KK06050 2C907280 2KK06051

(Ø14mm, Claw is 2 positions) (Ø18mm) (Ø14mm, Claw is 4 positions)
Shaft (No.3)
2KK06080 Shaft (No.3)
2KK06080

Shaft (No.3): 2C907300

Color of the housing: Black Color of the housing: Black Color of the housing: White

(Internal diameter of (Internal diameter of

the housing) the housing)

Claw (2 positions) Claw (4 positions)

Parts th at can b e u sed an d rep l aced (In d i vi d u al)

Machine before the service bulletin (Machine before this change) (Machine after this change)

Torque limiter
2KK06051 2C907280 2KK06051
(No.2)
Shaft
2KK06080 2C907300 2KK06080
(No.3)

(*) The above (the torque limiter and the shaft at the paper feed section) in the table are the parts that can be individually
used and replaced for each of the machine when replacing the parts.
Please use the above combination because the old and new shape for matching is different between 2KK… parts and
2C9… parts of the torque limiter and the shaft at the paper feed section.

3/3
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 11 / Firmware Upgrade
SB-A281/M
Date: 08-09-2010
Only CD 1118 / DC 2118

TOPIC:
The firmware is upgraded as follows.

CONTENTS OF CHANGE:

Contents Details
Preventing JAM when JAM may occur with difference from the actual paper size because the changed value is not
the setting of folio size informed to the engine and the processing is performed with the initial value even if the value
is changed at U035 <Setting folio size Length/Width>.
is changed
Therefore, this is corrected.
(The actual processing is performed with the initial value while the changed value is displayed
MAIN + ENGINE

on the panel.)
Measure against The panel may lock up due to continuing to wait for the signal that is sent from the engine
panel lock-up board to the main board when the signal is not sent depending on timing of pushing the start
key in the following setting.
- The original is scanned at the table
- Copy is executed while opening the platen cover
- Original of the second pages and after of continuous scanning
(Not occurring at the first page of the original)
- The start key is immediately pushed after setting the original

FIRMWARE CD 1118 / DC 2118

Type Program No. Check SUM VER. Remarks
MAIN ---- ---- 2KK_2000.001.028 only DIMM (No.1) New
ENGINE ---- ---- 2KK_1000.007.001 only DIMM (No.1) New
LANGUAGE ---- ---- 2KK_8100.001.007 only DIMM (No.1)
Separate firmware of MAIN, ENGINE and LANGUAGE is not supplied.

Old Part New Part Q’ty Compatibility

No. Description SP Remarks
No. No.
Old New Old New
PARTS DIMM PWB ASSY
1 2KK94583 2KK94589 - 1 - O O CD 1118 / DC 2118
WITH SOFTWARE
Parts with “O” indicates regular maintenance parts.

1/2
Classification: Entire Stock Rework
In-Field modification at next visit
X In-Field modification by case
No modification necessary

Field Measure: Please upgrade the main firmware in case the above phenomenon arises.

Serial Nos.: CD 1118 / DC 2118 planned from September 2010 production.

2/2
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 12 / Correcting Parts List – >COVER INNER LEFT<

Beh-Mey/M
Date: 07-02-2011

TOPIC:
The parts number of the cover inner left (No.1) is registered.

FIG. 16 Electrical Components 1 (CD 1118 / DC 2118)

FIG. 19 Electrical Components 1 (CD 1218, CD 1222 / DC 2218, DC 2222

1 .

Old Part New Part Q’ty Compatibility

No. Description SP Remarks
No. No.
Old New Old New

1 ------------ 2KK12010 COVER INNER LEFT - 1 - O -

Classification: Entire Stock Rework

In-Field modification at next visit
In-Field modification by case
X No modification necessary

Field Measure: service part (only)

Serial Nos.:

1/1
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 13 / DP 420 - Measure against paper jam

COM-B095/M
Date: 19-04-2011

TOPIC:
Rear part of the DP frame guide may be warped by the torque from the DP hinges in high temperature environment and the
level is higher than the original guide plate at the main machine side. Then, leading edge of the original may be caught by
the guide that may cause jam (J7*) or blurred image. - Therefore, following are changed.

CONTENT OF CHANGES:
Following are changed to improve margin for paper conveying.

5 pcs. (5 locations) of FILM PULLEY(No3) are currently affixed at the leading edge of the guide.

(Field measure) FILM BASE SP(No1) are affixed on 5 locations of FILM PULLEY(No3).
(Affixed on the current films)
(Production) 2 locations at the rear side are changed to FILM BASE(No2).
*Refer to the next page for details.

Guide and original guide plate Cross-section view

(Normal guide level) (High guide level)
Guide (part of DP frame)
DP Paper Paper

Guide
Top of guide
Film (No.1)
Original guide plate
Original guide plate
Leading edge of original may be caught by the DP guide
Original guide plate
if the level is high. Film (No.1) are added.

1/4
BEFORE:

Machine front side

<X/Y 5 locations>

FILM PULLEY(No.3)
(X) front side 3 locations

(Y) rear side 2 locations

PRODUCTION MEASURE:
2 locations of FILM at the rear side marked (Y) are changed.

No.3 11mm
7±0.5mm

21mm (t=0.125mm)

FILM PULLEY(No.3)  FILM BASE(No.2)

(Y 2 locations only)
No.2 7±0.5mm 12.5mm
1.5mm
<FILM BASE (No.2) alignment> (t=0.2mm)

(shaded area : double-side tape)

Run-over tolerance from guide 1.5mm

Range
Range

2/4
FIELD MEASURE:
FILM (No.1) is added to 5 locations of FILM PULLEY(No.3) that are currently affixed on the DP guide.
(FILM (No.1) may be affixed on 3 locations at the front side to improve the margin, however, in case the DP hinge is aligned
to the maximum, front 3 locations may run over the original guide plate. Do not affix FILM if it runs over)

Affixing condition
<FILM (No.1)>
FILM (No.1)

11.5mmm
No.3 3mm
(t=0.075mm)
21mm
No.1
(shaded area : double-side tape)

Affixing FILM (No.1)

No Procedures Detailed view

Take out GUIDE READING

GUIDE READING
2 points
1
screws

Clean the surface of 5 locations of FILM Machine rear Machine front

PULLEY (No.3) to affix FILM (No.1) with
alcohol and then affix it. Affix FILM (No.1) on
FILM PULLEY (No.3)
*Do not peel off FILM PULLEY(No.3) but
overlay on it.
2

(Detail view) No.3 No.1

Leading edge of Run-over tolerance

the guide 1.5mm

Reinstall GUIDE READING that was taken out

GUIDE READING
in the procedure 1.
Check if FILM (No.1) does not run
over the original guide plate.
FILM (No.1)
3 (In case the DP hinge is aligned to the
maximum, it may run over the original guide
plate. Check amount of run-over. Do not affix
FILM at front side if it runs over.
Original guide plate
(Do not run over with FILM (No.1))

3/4
 Check machine by side view if DP A) Correcting DP
has no gap or is not warped.
DP Open DP and
In case gap or warp is found, adjust
A and B. push gently
Front

A) Rear part of the DP may be warped in case

book original is placed and DP is pressed too Frame warps Original
much. Correct it by once opening DP and gently
4 push as shown in the figure right. B) Level adjustment with adjuster screw

B) Adjust the level with the adjuster

Screw at the machine rear side.

Adjuster screw

Old Part New Part Q’ty Compatibility

No. Description Remarks
No. No.
Old New Old New
SET (5 pcs.)
1 -------- 3MX94060 PARTS FILM BASE SP - 1 - O *1
Only for field measure

2 -------- 3MX02080 FILM BASE - 1 - for production

3 3K524110 3K524110 FILM PULLEY *2 for production

*1) Affix it on FILM PULLEY(No.3) on the DP guide.

Thickness of the film and FILM PULLEY (No.3) is same as the one of FILM BASE (No.2)
*2) 2 pcs. at the rear side are changed to No.2 (production line)

Classification: Entire Stock Rework

In-Field modification at next visit
X In-Field modification by case
No modification necessary

Field Measure: Please affix FILM (No.1) that is a set of 5 pcs. when the above phenomenon arises.
(Refer to page 3 to affix the FILM ).

Serial Nos.: DP 420

 Planned from the production in March 2011.
DP 670

4/4
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 14 / Correcting Parts List – >PWB RFID<

PCI-B116/M
Date: 27-05-2011

TOPIC:
The parts number of the PWB RFID (No.1) is registered.

FIG. 16 Electrical Components 1 (CD 1118 / DC 2118)

FIG. 19 Electrical Components 1 (CD 1218, CD 1222 / DC 2218, DC 2222

1 .

Old Part New Part Q’ty Compatibility

No. Description SP Remarks
No. No.
Old New Old New

1 ------------ 2KP94200 PWB RFID - 1 - O -

Classification: Entire Stock Rework

In-Field modification at next visit
In-Field modification by case
X No modification necessary

Field Measure: service part (only)


Serial Nos.: 


1/1
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 15 / Firmware Upgrade
2KH-B210/M
Date: 18-07-2011

TOPIC:
The firmware is upgraded as follows.

CONTENTS OF CHANGE:

 Extended after-job aging is implemented.

Lateral black bands may appear at low temperature and low humidity and the after-job aging is changed to extend it by the maintenance
mode in order to clean the drum surface with dirt and foreign objects. (Set by the new mode U166 - Extend Driving Time).
 Corrective measures for the background image appearing at the leading edge.
The background image may appear at the leading edge and so, the paper.
 Corrective measures for the failure of the DP copy just after the power saver mode.
When [Start] key is pressed just after setting multiple sheets of originals smaller than A4/Letter to the DP during the power saver mode,
the DP starts feeding the originals after restarting from the power saver mode. Then, [Restart, press Start key] may appear when the DP
is about to feed the 2nd sheet after recovery from the power saver mode. Therefore, this is corrected.

NEW:
U166 Extend Drive Time is newly implemented to set the aging time.
Simulation U166 - TIME(S)
Value setting: 0  Aging not extended
1  Aging extended by 3sec.
2  Aging extended by 4sec.
3  Aging extended by 5sec.
4  Aging extended by 6sec.
5  Aging extended by 7sec.
6  Aging extended by 8sec.
7  Aging extended by 9sec.

FIRMWARE UPGRADE
Type Program No. Check-S VER. Remarks
MAIN ---- ---- 2KK_2000.001.030 only CD 1118 / DC 2118 (DIMM No.1)  New
ENGINE ---- ---- 2KK_1000.008.001 only CD 1118 / DC 2118 (DIMM No.1)  New
LANGUAGE ---- ---- 2KK_8100.001.007 only CD 1118 / DC 2118 (DIMM No.1)

Separate firmware of MAIN, ENGINE and LANGUAGE is not supplied.

Old Part New Part Q’ty Compatibility

No. Description SP Remarks
No. No.
Old New Old New

1 2KK94583 2KK9458A DIMM WITH SOFTWARE 1 1 X O O only CD 1118 / DC 2118

1/2
 FIRMWARE UPGRADE
Type Program No. Check-S VER. Remarks
MAIN (IPU) 2KH_2000.001.045 ---- 001.045 only CD 1218, DC 1222 / DC 2218, DC 1222  New
ENGINE 2KK_1000.008.001 ---- 008.001 only CD 1218, DC 1222 / DC 2218, DC 1222  New
LANGUAGE E 2KH_81XE.001.003 ---- 001.003 only CD 1218, DC 1222 / DC 2218, DC 1222

PRINTER FS 2KH_3F00.002.002 ---- 002.002 only CD 1218, DC 1222 / DC 2218, DC 1222

Separate firmware of MAIN, ENGINE and LANGUAGE is not supplied.

Classification: Entire Stock Rework

In-Field modification at next visit
X In-Field modification by case
No modification necessary

Field Measure: Please upgrade the firmware when the above problem arises.
CD 1118 / DC 2118 upgrade only be DIMM (No.1)

Serial Nos.:  1118 / DC 2118
CD
CD 1218 / DC 2218 Planned from June 2011 production.
CD 1222 / DC 2222


2/2
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 16 / Registration actuator spring coming off

2KH-B210/M
Date: 19-07-2011

TOPIC:
SPRING REGIST SW may contact the paper and it may come off when clearing the jam, etc. Therefore, the shape of
SPRING REGIST SW is changed.
Please note that jam* occurs if SPRING REGIST SW comes off and the registration actuator does not come back.
(*The registration switch is not turned off and the multiple-sheet jam (JAM20/21/22) may be detected.)

CONTENTS OF CHANGE:

The hooking part to the actuator of SPRING REGIST SW (No1) is extended to make it hard to come off.

Left side of machine Old type spring

(No.1)

Edge of paper may catch the spring when clearing a

jammed paper to cause it coming off

Left cover is opened

New type spring

(No.1)

SPRING REGIST SW (No.1)

･ Hooking part of the spring is extended to securely hold the spring.
･ The edge of the spring is wound and it avoids the edge is caught by
paper.

1/2
 Old Part New Part Q’ty Compatibility
No. Description SP Remarks
No. No.
Old New Old New

1 2KK24270 2KK24271 SPRING REGIST SW 1 1 X O

Classification: Entire Stock Rework

In-Field modification at next visit
X In-Field modification by case
No modification necessary

Field Measure: Please replace with the new part (No.1) when the above phenomenon arises.

Serial Nos.:  1118 / DC 2118
CD
CD 1218 / DC 2218 Planned from June 2011 production.
CD 1222 / DC 2222


2/2
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 17 / Correcting Parts List – FIG. 17 + FIG. 20 (Panel)

PCI-B248M
Date: 26-08-2011

TOPIC:
The following part names listed in the parts list are changed.

FIG. 17 Electrical Components - CD 1118 / DC 2118

FIG. 20 Electrical Components - CD 1218, DC 1222 / DC 2218, DC 2218

3 .

2 .

WRONG CORRECT

Fig. No. Part No. Description Fig. No. Part No. Description

17 2 2KK46250 FFC PANEL LEFT 17 2 2KK46260 FFC PANEL RIGHT

17 3 2KK46260 FFC PANEL RIGHT 17 3 2KK46250 FFC PANEL LEFT

20 2 2KH46020 FFC PANEL LEFT 20 2 2KH46030 FFC PANEL RIGHT

20 3 2KH46030 FFC PANEL RIGHT 20 3 2KH46020 FFC PANEL LEFT

FIG 17  only CD 1118 / DC 2118

FIG 20  only CD 1218, CD 1222 / DC 2218, DC 2222

1/2
Classification: Entire Stock Rework
In-Field modification at next visit
In-Field modification by case
X No modification necessary

Field Measure: Service information only


Serial Nos.: 


2/2
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 18 / Correcting Parts List – FIG. 12 + FIG 15 (Fuser..)

PCI-B300M
Date: 26-09-2011

TOPIC:
The Parts number is set up to the parts below (No. A) in the fuser section.

FIG. 12 Fuser Section - CD 1118 / DC 2118

FIG. 15 Fuser Section - CD 1218, DC 1222 / DC 2218, DC 2218

A .

Old Part New Part Q’ty Compatibility

No. Description Remarks
No. No.
Old New Old New
set up to service
A ---------- 2KK25040 GUIDE FUSER REAR - 1 - O parts

Classification: Entire Stock Rework

In-Field modification at next visit
In-Field modification by case
X No modification necessary

Field Measure: Service information only


Serial Nos.: 


1/1
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 19 / Conformity to the ErP Lot6 (Change of Parts)

2KK-C146r1/M
Date: 17-07-2012

Only  CD 1118 / DC 2118 (Rev.1 - Change of the power source PWB)

TOPIC:
For conforming to the standby and off mode power consumption requirements (Energy related-Products Lot6) in EU
countries, the main power off timer function (Note 1) is added by changing the main switch, main engine PWB and the
neighbouring parts and upgrading the firmware. (Please refer to next page and after for the details.)
Note: It is the new function for turning the main switch off automatically after passing the certain time since the last time of
using the machine.

CONTENT OF CHANGES:
The new product codes are set up for the models conforming to the ErP Lot6 that add the main power off timer function. As
for the models conforming to the ErP Lot6, the distinction label indicating the product code is affixed on the hinge part of the
front cover.

Hinge part of the front cover

Affixed the distinction label

indicating the product code of the
models conforming to the ErP Lot6.

Operational compatibility table

The operation differs by the combinations of the main machine type distinguished with the 1st to 3rd digits of the serial
number (distinguished by the new firmware), the firmware and hardware (Main engine PWB (No.2, 3), etc.).

Main machine Firmware Hardware Usable Operation

New New O Unable to switch the power OFF of the main switch (Conform to the ErP Lot6)

New Model New Current X Unusable by displaying the system error code A210 (*)
(conforming to the ErP Lot6)
Current New X Unusable (Not conform to the ErP Lot6)
Current Current X Unusable (Not conform to the ErP Lot6)
New New O Not switch the power OFF of the main switch.
New Current O Not switch the power OFF of the main switch.
Current model
Current New O Not switch the power OFF of the main switch.
Current Current O Not switch the power OFF of the main switch.
* A210 is displayed when the main switch is not turned off even if the set time comes.

1/6
CONTENT OF CHANGES (DETAILS):
1.) Change to the main switch with the reset function.
For reducing the standby power consumption, the main switch is changed to the one (No.1) with the reset function including the
solenoid so that the main switch is automatically turned off after passing the certain time (Default is “1 hour”) since the last time of using
the machine.

2.) Change of the main engine PWB

The drive circuit for the main switch with the reset function is added according to the above change 1.

3.) Upgrade of the firmware

The firmware is upgraded for adding the main power OFF timer function according to the above change 1.

4.) Bundling a leaflet describing the procedures for setting the main power OFF timer function.
The leaflet describing the procedures for setting the main power OFF timer for the models conforming to the ErP Lot6 is bundled in the
main machine.

5.) Change of the right lower cover and right lower frame, disuse of the main switch cover.
Due to expanding the width of the main switch, the width of the right lower cover (No.5) and right lower frame (Not supplied as the
individual parts) is also expanded. And, the main switch cover (No.6) covering the main switch is disused according to this change.

6.) Adding the wire controlling the main switch with the reset function, combining the wires according to that.
WIRE PF (Old No.7) and WIRE CONTAINER (No.8) are combined and the wire (the wire between B and C in the figure in page5)
controlling the new main switch is added. (New No.7).

7.) Change of the power source PWB. (Rev.1)

For avoiding contact with the new main switch (No.1) that conforms to the ErP Lot 6, the pins of the capacitors (C4, C5) mounted on the
power source PWB (No.9) are bent and the capacitors are fixed with adhesive to the side of the neighboring inductor or to the mounted
side of the PWB.

CONTENTS OF UPGRADING THE FIRMWARE-(DIMM):

Conformity to European ErP directive (Lot6).
For conforming to the European ErP directive (Lot6), the main power off function (off mode) is added
Added the System Menu 60.
1. Turned the main switch off automatically after passing the certain time since the last time of using the machine. (Default: 1 hour)
System Menu [60. Power Off Timer] (*) is added for enabling to select the time interval.
Choices: 1 hour, 2 hours, 3 hours, 4 hours, 5 hours, 6 hours, 9 hours, 12 hours, 1 day, 2 days, 3 days, 4 days, 5 days, 6 days and
1 week (*) [60. Power Off Timer] is not displayed in the models not conforming to the ErP Lot6.
2. Not switched to the off mode if installing the option or enhancement. However, the OFF mode is switched automatically by the main
power off timer according to the setting of the Maintenance Mode U257 in spite of this state.
Options/enhancements with the automatic switch disabled
- Printer interface board (Printing System(Z))
- Document Processor (DP-420)
- Duplex (DU-420)
- Enlargement memory
- Paper cassette (PF-420)
- Key counter
Added the Maintenance Mode U257 [Set Auto Shutoff].
Added for enabling to switch to the Off mode even if installing the options/enhancements with the automatic switch to the Off mode disabled.
- on ... Switch to the Off mode
(Its setting is possible for the models not conforming to the ErP Lot6. However its motion is usable only for the models conforming to the ErP Lot6.)
- off ... Not switch to the Off mode (Default setting)
Changed the Maintenance Mode U004.
Added the check result display whether the models conforming to the ErP Lot6 or not to the U004 [Check machine number].
Group 1: Display the machine number
Group 2: Display the check result whether the models conforming to the ErP Lot6 or not (00: Not conformity 01: Conformity)
(Group 2 appears when [Text] and [Photo] are turned by the image quality key.)
The check result is also indicated on STATUS REPORT.
004: Check machine number **********(Serial No) 1 (Check result)

2/6
CONTENTS OF UPGRADING THE HARDWARE:

Change of the main switch (No.1)

NEW

Width: 12.8mm Width: 21.7mm

Change of the right lower cover (No.4) and right lower frame (not supplied as the individual parts)
Disuse of the main switch cover (No.5)

Below is the old state New right lower cover (No.4)

Opening for the main switch

Width (X): 16.4mm --> 26.6mm

Opening for the main switch

Width (Y): 12.95mm --> 22.05mm

Disused the main switch

cover (No.5)

New right lower frame

Y (Not supplied as the individual
parts)

Adding the wire controlling the main switch with the reset function and combining the wires according to this change
WIRE PF RESET SW (New No.5): The color of the wire between A and B, B and C in the figure below is blue>

The wire that is same as the current WIRE PF (Old

No.6) and the wire for controlling the new main
switch (The wire between B and C) are combined
by the bundling band.

C B
A

A: Connecting to the switch detecting the toner WIRE CONTAINER (No.7)

container in the main drive unit.
B: Connecting to the connector YC19 on the B
main engine PWB.
A
C: Connecting to the new main switch
Disused this wire because WIRE PF RESET SW
(New No.6) is combined. (Wire color: Gray)

3/6
 View of the main engine PWB from the machine backside

Connector YC19

New main engine PWB

(No.2)

WIRE PF RESET SW (New No.6)

: Blue wire in the left figure

Switch detecting the toner container

Machine inside
New main switch (No.1)

Distinction of the old and new main engine PWB (No.2)

The silk print on the left upper part of the component side of the main engine PWB (No.2) is changed as below.

Underlined sections indicate the changed parts

7PA0370-C 7PA0370-D
NEW
7PA0370CAF+GH01 7PA0370DMF+GH01

Silk print

4/6
Change of the power source PWB.
Below is the fitting position of the main switch (new No.1) that conforms to the ErP Lot6 viewed from the machine inside.

New main switch (No.1)

Inductor

Bent so that its - Capacitor C4

height becomes
: Bent toward the inductor L1 and then fix to the side
12mm or less.
of the inductor L1 with adhesive.
Capacitor C5 Capacitor C4 - Capacitor C5
: Bent toward the reverse side of the capacitor C4
and fix to the mounted side of the PWB with
adhesive.

Distinction of the new and old power source PWB (No.8)

Inductor L1

Capacitor C4, C5 New and old power source PWBs can be distinguished by the
number indicated on the label that is affixed on the mounted
side of the PWB.
(Before) 302KK45020-01 or 302KK45020-02
(After) 302KK45021-01 or 302KK4502█
(*) █ is painted out with the black marker.

5/6
 Old Part New Part Q’ty Compatibility
No. Description Remarks
No. No.
Old New Old New

1 SC023350 SC134830 SWITCH SEESAW 1 1 X X

X
2 2KL9401C 2KL94030 PARTS PWB MAIN ENGINE ASSY SP 1 1 O
(*1)
3 2KK9458B 2KK9458C DIMM PWB ASSY WITH SOFTWARE 1 1 X O

4 2KK04130 2KK04320 COVER RIGHT LOW L 1 1 X X

5 2H004241 ------------ COVER MAIN SW 1 - X -

6 2KK46100 2KK46380 WIRE PF SW RESET 1 1 X X

7 2KK46320 ------------ WIRE CONTAINER 1 - X -

X
8 2KK94390 2KK94391 PARTS LVU200 SP 1 1 O
(*1)
*1: Please surely use the new parts for the models conforming to the ErP Lot6.
As for the current European models and the other spec models, either the old or new parts are usable.
The other parts have no compatibility, so please use the parts according to the machine type (before/after this change).

Classification: Entire Stock Rework

In-Field modification at next visit
In-Field modification by case
X No modification necessary

Field Measure: Please surely use the parts conforming to the ErP Lot6 (New No1 thru 4, 6) for the models
conforming to it when replacing the parts.
As for the current model, no particular problems are expected if using either the old or new main
engine PWB (No.2), DIMM PWB (No.3). However, please use the current parts (Old No.1, 4 thru 7)
for the other parts.

Serial Nos.: CD  1118 / DC 2118 Models conforming to the ErP Lot6: From the first mass-production.
The production of the current models
It’s the first digit of the serial number is “Q” is switched to the models
conforming to the ErP Lot6 in turn.


6/6
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB 20 / DP 420 - Corrective measures for DP hang-down

COM-D231/M
Date: 03-12-2013

TOPIC:
The strength to hold the hinge when opening the DP is weakened after
prolonged use. If the hinge cannot hold the DP opened at the free stop
angle or higher angle, the DP may hang-down. LEFT HINGE

Thus, the following is changed.

CONTENT OF CHANGES:
The springs inside the LEFT HINGE are increased from 2 pcs to 4 pcs for improving the force to hold the DP.

NEW

Total 4 springs (Added the new 2

2 current springs springs inside the current springs.)

Old Part New Part Q’ty Compatibility

No. Description Remarks
No. No.
Old New Old New
1 3K502020 3K502021 LEFT HINGE 1 1 X X

Classification: Entire Stock Rework

In-Field modification at next visit
X In-Field modification by case
No modification necessary

Field Measure: Replace the LEFT HINGE with the new one when the above phenomenon arises.

Serial Nos.: DP 420A

DP 670A After using up the old stock.
DP 670B 

1/1
Technical Bulletin UTAX CD 1118
UTAX CD 1218
UTAX CD 1222
TA DC 2118
TA DC 2218
TA DC 2222

TB-21S 3MY-E155/M Date: 17-09-2014

Priority: …A  highest priority / …B  second priority / …C  other / S… Service Information

Print System Z: Note when replacing the board (Service parts only)
Only  CD 1118 / DC 2118

NOTE:
There is a restriction for parts procurement reason (discontinuation of the old part on the maker side). (*) The printer board
(No.1) is supplied as a service parts. Together with this change, note the default setting of the dip switch will be FULL .

Restriction (*)
-If using with HIGH , it might not be connected to the network.
-If changing from HIGH to FULL , the output of complex images might be delayed (from 0 to 3 seconds).

Since there is no change of the parts number together with this change, refer to the below for the identification of printer
board (No.1) between old and new.

Printer board No.11 Printer board No.11

Location of dip switch

The location to identify old from new

Dip switch
Identification method: Fill the [A] part with black (Factory setting from this change: FULL )

Printer board packing case

Black marking is added to the right side

of the barcode label pasted to the packing case

1/2
 Old Part New Part Q’ty Compatibility Affected model
No. Description
No. No. Remarks
Old New Old New
1 3MY94014 3MY94014 PARTS GDI PWB ASSY SP 1 1 O O

Classification: Entire Stock Rework

In-Field modification at next visit
In-Field modification by case
X Information only
No modification necessary

Field Measure: Note when using the printer board (No.1).


Serial Nos.:  CD 1118 / DC 2118 From the next shipment (September, 2014).


2/2