Mathematical Statistician and Engineering Applications
ISSN: 2094-0343
2326-9865
Password Based Circuit Breaker Using GSMModule
B. Malleswari1, K. Anitha2, V. Jaikumar3 and A. Arun Chakravarthy
1,2,3
department Of Ece, 4department Of It, Qis College Of Engineering And Technology
Article Info Abstract
Page Number: 101 - 107 An automatic electric switch known as a circuit breaker is used to safeguard
Publication Issue: an electrical circuit from harm brought on by overloading or short circuits.
Vol 68 No. 1 (2019) When we use our hands, we observe an increase in lethal electrical threats
to cable workers during power line repairs because of a lack of
communication and interaction between the repair employees and the power
Article History station workers. This project is made to tackle the issue with a design
Article Received: breaker so that only an authorised person may use it with a password in
09 September 2019 order to prevent such risks. Arduino has complete control over the system.
Revised: 16 October 2019 The circuit breakers, which are switched on or off by a flashlight, are
Accepted: 21 November 2019 activated by entering the password into the keypad. Remote system control
Publication: 28 December 2019 is possible thanks to the global mobile system (GSM) circuit. This leads to
solving the problem of wasting time.
Keywords: Circuit breaker, Arduino, Relay, GSM Module.
INTRODUCTION
Based on embedded system. In this project, Arduino is utilized to manage all activities
connected to the password system. For this procedure, we require a part like Arduino control
circuitry and a power source like a keypad. Passwords for a different download function
attached to the controller are entered using this keypad. To secure the lineman's safety, this
project offers a solution to this issue. Since it has a very low retention rate.
There are several items on the market now, but they are all highly expensive and need a lot
of time to use. The time needed for the lineman to recover when in the head is shortened by
our gadget. The parts that our model requires are easily accessible on the market. Our
project's major goal is to cut down on linemen time. Currently, if there is a weakness in the
power line, the line will easily modify the power line and, after arriving at the station, turn
off the power supply to the line by adding a secret word. By entering a secret key, the man
will modify the stock in a specific line. A natural electric switch that is intended is called an
electric switch.
This action is meant to handle the problem by disrupting the system until the person
authorised to execute it addresses the issue in order to prevent such errors. Arduino entirely
obstructs the frame. To unlock or contain circuit breakers, a secret phrase must be entered on
the keypad. which a flashlight indicates. The control of the framework is made possible by
the global portable circuit framework (GSM). This makes it challenging for us to waste time.
The GSM module needed to deliver SMS is a
LITERARTURE SURVEY
"User-based flexible circuit breaker-based electric lineman protection": A circuit breaker is
Vol. 68 No. 1 (2019)
101
http://philstat.org.ph
Mathematical Statistician and Engineering Applications
ISSN: 2094-0343
2326-9865
an automatic electric switch created to guard against short circuit or overload damage to the
electrical circuit. Its main job is to stop the current flow and identify the incorrect status. The
circuit breaker can be reset (manually or automatically) to resume normal operation, unlike a
fuse, which can only be used once before needing to be replaced. When performing manual
labor, we observe an increase in fatal electrical risks on the lineman during electrical repairs
as a result of poor communication between repair workers and employees of the power
plant.
The breaker may be made to only be operable by authorised users with a password in order
to avoid such risks. A setting for changing the password is also included here. The relay
turns on or off the circuit breaker, which is shown by a lamp, and the keypad is used to enter
the password. Because there is a lack of communication and cooperation between the care
staff and the employees of the power station, serious electrical threats to linemen increase
during electrical wiring.
With the use of the Intimation HT Wire Sag GSM app and Password Based Circuit Breaker,
Vishal S. Kamble and Pramod M. Murari learned Electric Man security. The suggested
approach offers a remedy that guarantees the safety of the repair team; specifically, the line
driver who discovers the problem in the line lineman sends an SMS and the system line is
turned off again after fixing the error and demonstrating good energy savings. which
explains why a lineman is still present and working on the power cord. The suggested device
uses Arduino only.
BACKGROUND
EXISTING METHOD:
Circuit breakers are crucial to keeping the security of the system. Because a malfunction
could result in a partial shutdown and dangerous working circumstances. There could be a
communication breakdown between the power line and the conductor of the sub-station or
crew while the distribution cables are being maintained. Electrical wiring may pose a
lifelong risk due to this communication gap. The sole person in line has control over the
OPEN/CLOSING line. Customers are inconvenienced because the entire line is shut off
while repairs are being made.
Fig1: Miniature circuit breaker
Vol. 68 No. 1 (2019)
102
http://philstat.org.ph
Mathematical Statistician and Engineering Applications
ISSN: 2094-0343
2326-9865
Fig 2: Electrical Fuse
PROPOSED SYSTEM:
Now let’s see how the project works. First, when the power is on, the LCD displays the
reception screen and asks you to enter a password to unlock it. In our case, the password was
reset. Using Keyboard, the password is also entered as we type the password appears on the
LCD. If the wrong password is entered, it will display an incorrect message and ask you to
enter it again. When the correct password is entered, a large circuit breaker screen is opened.
Now the status of 1 Arduino load connected to the LCD is shown on LCD whether it is ON
or off.
By pressing the same password, the load can be locked. The GSM modem is an integral part
of the proposed 'A' instructions obtained by Arduino. By default, permission is received via
SMS sent depending on the status and permission of the senders. The LCD screen is used here
to display full functionality.
Fig 2: Proposed system
HARDWARE COMPONENTS:
• Arduino UNO
• 16 x 2 LCD display
• 4 * 4 Matrix Keyboard
• Relay
• Step down transformer (9-0-9)
• Mobile phone
• GSM module
Vol. 68 No. 1 (2019)
103
http://philstat.org.ph
Mathematical Statistician and Engineering Applications
ISSN: 2094-0343
2326-9865
• Power supply
BLOCK DIAGRAM:
Fig 3: Block Diagram
CIRCUIT DIAGRAM:
When the circuit is closed which is normal, the contacts contact and manage currently under
this condition. Under a closed-circuit breaker, the contact conductors are currently known as
electrodes that connect due to the pressure of the spring. Switching and maintenance of the
system is maintained
by opening or closing the circuit breaker.
Fig4: Circuit Diagram
Under a closed-circuit breaker, the contact conductors are currently known as electrodes that
connect due to the pressure of the spring. Switching and maintenance of the system is
maintained by opening or closing the circuit breaker arms.
ALGORITHM:
Step 1: Assemble all components (Arduino Uno, LED, LCD display, down transformer,
Relay, GSM Module). Step 2: Sort All Components Based on Circuit Drawing.
Vol. 68 No. 1 (2019)
104
http://philstat.org.ph
Mathematical Statistician and Engineering Applications
ISSN: 2094-0343
2326-9865
Step 3: Now place the adapter on the switch board and turn on the switch.
Step 4: Now upload the code to Arduino by inserting a single cable end into the USB port.
Step 5: Now insert the SIM card into the GSM Module.
Step 6: Now we have to enter the password with the help of keypad. Step 7: The entered
password is compared to the stored password.
Step 8: Now, if the password is correct, then the circuit shortcut changes its status (i.e., if
it is already OPEN, now CLOSED, now OPEN) and displays the status on the LCD.
Step 9: If the password is incorrect, the LCD will display the "incorrect password". Step 10:
After some time, Arduino asks for a password by displaying "enter password".
Step 11: If the password is entered correctly, it will send an SMS to the cell phone via the
GSM Module.
FLOWCHART:
The step-by-step operation of the proposed algorithm is described below in Figure 5,
Fig 5: Flow chart
RESULTS AND DISCUSSIONS: The system's prototype working scenario and results
are shown in the following steps and pictures.
Vol. 68 No. 1 (2019)
105
http://philstat.org.ph
Mathematical Statistician and Engineering Applications
ISSN: 2094-0343
2326-9865
Step1: Project prototype Step2: Displays the enter 4-digit password
Step3: Entering the password Step4: Displays entered password
Step5: Line ON/OFF proposed system Step6: Overview of proposed system
CONCLUSION & FUTURESCOPE:
The project is organized in such a way that the rope access technician must enter the
password ON / ON card. Now if there is an error in the power line, the lineman will close the
power line by entering a password and properly correcting the power line, and after accessing
the lineman machine of the sub-channel in providing a specific line by entering the
password.
REFERENCES:
1. M. Kezunovic, “Improving circuit breaker maintenance management services using
mobile agent software technology” IEEE.
Vol. 68 No. 1 (2019)
106
http://philstat.org.ph
Mathematical Statistician and Engineering Applications
ISSN: 2094-0343
2326-9865
2. Charles H. Flurscheim (ed), Theory and Design of Power Circuit Breaker, Second
Edition ET, 2011 ISBN 0906048702 Chapter I.
3. Narendra Khandelwal, Tanuj Manglani, Ganpat Singh, Amit Kumar, Dilip Khatri,
"Automatic load distribution with password-protected circuit breakers" International
Journal of Recent Research and Review, vol. VIII, Issued March 1, 2015.
4. 8051 Microcontroller Architecture, Programming & Applications -Kenneth J. Ayala
5. "8051 Microcontroller and Embedded Systems" by Muhammad Ali Mazidi and Janice
Gillispie Mazidi. Pearson Education.
6. JSRD - International Journal of Scientific Research and Development | Vol. 4, Issued
01, 2016 | ISSN (online): 2321-0.
7. P Ramprakash, M Sakthivadivel, N Krishnaraj, J Ramprasath. ”Host-based Intrusion
Detection System using Sequence of System Calls” International Journal of Engineering
and Management Research, Vandana Publications, Volume 4, Issue 2, 241-247, 2014
8. N Krishnaraj, S Smys.”A multihoming ACO-MDV routing for maximum power
efficiency in an IoT environment” Wireless Personal Communications 109 (1), 243-256,
2019.
9. N Krishnaraj, R Bhuvanesh Kumar, D Rajeshwar, T Sanjay Kumar, Implementation of
energy aware modified distance vector routing protocol for energy efficiency in wireless
sensor networks, 2020 International Conference on Inventive Computation
Technologies (ICICT),201-204
10. Ibrahim, S. Jafar Ali, and M. Thangamani. "Enhanced singular value decomposition for
prediction of drugs and diseases with hepatocellular carcinoma based on multi-source
bat algorithm based random walk." Measurement 141 (2019): 176-183.
https://doi.org/10.1016/j.measurement.2019.02.056
11. Ibrahim, Jafar Ali S., S. Rajasekar, Varsha, M. Karunakaran, K. Kasirajan, Kalyan NS
Chakravarthy, V. Kumar, and K. J. Kaur. "Recent advances in performance and effect
of Zr doping with ZnO thin film sensor in ammonia vapour sensing." GLOBAL NEST
JOURNAL 23, no. 4 (2021): 526-531. https://doi.org/10.30955/gnj.004020 ,
https://journal.gnest.org/publication/gnest_04020
12. N.S. Kalyan Chakravarthy, B. Karthikeyan, K. Alhaf Malik, D.Bujji Babbu,. K. Nithya
S.Jafar Ali Ibrahim , Survey of Cooperative Routing Algorithms in Wireless Sensor
Networks, Journal of Annals of the Romanian Society for Cell Biology ,5316-5320,
2021
13. Rajmohan, G, Chinnappan, CV, John William, AD, Chandrakrishan Balakrishnan, S,
Anand Muthu, B, Manogaran, G. Revamping land coverage analysis using aerial
satellite image mapping. Trans Emerging Tel Tech. 2021; 32:e3927.
https://doi.org/10.1002/ett.3927
14. Vignesh, C.C., Sivaparthipan, C.B., Daniel, J.A. et al. Adjacent Node based Energetic
Association Factor Routing Protocol in Wireless Sensor Networks. Wireless Pers
Commun 119, 3255–3270 (2021). https://doi.org/10.1007/s11277-021-08397-0.
15. C Chandru Vignesh, S Karthik, Predicting the position of adjacent nodes with QoS in
mobile ad hoc networks, Journal of Multimedia Tools and Applications, Springer
US,Vol 79, 8445-8457,2020
Vol. 68 No. 1 (2019)
107
http://philstat.org.ph
