Type 484

Cap H2
Inlet: Vessel connection
Type 5034
Outlet: Welded end
connection
Type
484
Safety Relief Valves
– spring loaded

Contents Chapter/Page
Materials
• HyTight Assembly 04/02
Type 484 How to order
Packed knob H4 • Numbering system 04/04
Inlet: Vessel connection • Article numbers 04/06
Type 5034
Pressure temperature ratings
Outlet: Welded end
• Metric Units + US Units 04/08
connection

Type 484
Dimensions – Bestseller
• Metric Units + US Units 04/09
Dimensions and weights
• Metric Units 04/10
• US Units 04/11
Option codes for available connections 04/12
Available options 04/13
Selection chart H8 04/14
Surface quality 04/15
Order information – Spare parts 04/16
Approvals 04/17
Type 5034
Capacities
Vessel connection
• Steam, Air, Water [Metric Units] 04/18
• Steam, Air, Water [US Units] 04/19
Determination of coefficient 04/20
of discharge Kdr /α w

LWN 483.01-E 04/01

 Type 484
How to order – Article numbers

Type 484
Cap H2
Inlet: Vessel connection Type 5034
Outlet: Welded end connection
Type 484

Type 484
Packed knob H4
Inlet: Vessel connection Type 5034
Outlet: Welded end connection

04/06 LWN 483.01-E

Type 484
How to order – Article numbers

Article numbers
Actual Orifice diameter d0 [mm] 13 25
Actual Orifice area A0 [mm2] 133 491
Actual Orifice diameter d0 [inch] 0,512 0,984
2
Actual Orifice area A0 [inch ] 0,206 0,761
O-ring material EPDM “D” J22 EPDM “D” J22
CR “K” J21 CR “K” J21
FKM “L” J23 FKM “L” J23
NBR “N” J30 NBR “N” J30
FFKM “C” J20 FFKM “C” J20
Body material: 1.4435 (316L)
Bonnet H2 Art.-No. 4844. 7722 7732
closed H4 Art.-No. 4844. 7724 7734
H8 Art.-No. 4844. 7728 7738
p [bar] S/G/L 0,3 – 16 0,1 – 16
p [psig] S/G/L 4,4 – 232 1,5 – 232
Vessel connection material: 1.4435 (316L) Please order separately
Vessel wall thickness [mm] ≤5 >5 ≤5 >5
Vessel wall thickness [inch] ≤ 13/64 > 13/64 ≤ 13/64 > 13/64
Art.-No. 5034. 0980 0981 0982 0983
Blind flange for pressure test: 1.4404 (316L) Please order separately
Art.-No. 138.8849.9000 138.8649.9000

Fitting information

Type 484
Safety valve

Vessel connection

Vessel

Due to the dead space free vessel connection, which is directly welded into the vessel wall, please note the required space between outlet
connection of the valve (e. g. clamps or flanges) and vessel wall. If required please order a longer outlet connection with your specifications.

LWN 483.01-E 04/07

 Type 484
HyTight Assembly

40 Cap H2

18 Adjusting screw
with bushing
19 Lock nut

16 Spring plate

9 Bonnet

54 Spring

12 Spindle

14 Pin /Split ring

17 Spring plate

8 Guide with bushing

68 Clamp

60 O-ring

21 Lift stopper

70 Elastomer bellows
Type 484

56 Nut

92 Screw

48 Vessel connection

61 7 57 67 1

Ball O-ring disc Pin O-ring Body

Type 484 HyTight

Cap H2
Inlet: Vessel connection Type 5034
Outlet: Welded end connection

04/02 LWN 483.01-E

Type 484
HyTight Assembly
Materials
Item Component Remarks Type 4844 HyTight

1.4435 (BN 2)*)

1 Body
SA 479 316L
1.4435
7 O-ring disc HyTight Assembly
316L

7.4 Soft seal O-ring “D” EPDM

“K” CR

“L” FKM

“N” NBR

“C” FFKM

1.4435
8 Guide with bushing PTFE + 15 % glass
316L
1.4404
9 Bonnet
316L
1.4404
12 Spindle
316L
1.4310 / 1.4404
14 Pin / Split ring
Stainless steel / 316L
1.4404
16 / 17 Spring plate
316L
Adjusting screw 1.4404 / PTFE
18 PTFE + 15 % glass
with bushing 316L / PTFE
1.4404
19 Lock nut
316L
1.4310
21 Lift stopper
Stainless steel
1.4404
40 Cap H2
316L
1.4310
54 Spring

Type 484
Stainless steel
1.4310
57 Pin
Stainless steel

60 O-ring EPDM

1.4401
61 Ball
316
1.4401
68 Clamp
316

70 Elastomer bellows EPDM

Vessel connection Type 5034

1.4435 (BN 2)*)
48 Vessel connection
SA 479 316L
1.4401
56 Nut
316

67 O-ring EPDM

1.4404
92 Screw
316L
Blind flange for 1.4404
–
pressure test 316L
Please notice:
*) The material 1.4435/SA 479 316L fulfils the requirements of – Modifications reserved by LESER.
the Swiss chemical and pharmaceutical industry Basler Norm (BN 2). – LESER can upgrade materials without notice.
For details please refer to LWN 290.90. – Every part can be replaced by other material acc. to customer specification.
LWN 483.01-E 04/03
 Type 484
Pressure temperature ratings

Metric Units
Actual Orifice diameter d0 [mm] 13 25
Actual Orifice area A0 [mm2] 133 491
Body material: 1.4435 (316L)
Minimum
set pressure p [bar] S/G/L 0,3 0,1
Maximum
set pressure p [bar] S/G/L 16 16
*)
Temperature range Minimum Maximum Minimum Maximum
EPDM [° C] -45 +150 -45 +150
CR [° C] -40 +100 -40 +100
FKM [° C] -20 +180 -20 +180
NBR [° C] -25 +110 -25 +110
FFKM [° C] 0 +250 0 +250

US Units
Actual Orifice diameter d0 [inch] 0,512 0,984
Actual Orifice area A0 [inch2] 0,206 0,761
Body material: 1.4435 (316L)
Minimum
set pressure p [psig] S/G/L 4,4 1,5
Maximum
set pressure p [psig] S/G/L 232 232

Temperature range*) Minimum Maximum Minimum Maximum

EPDM [° F] -49 +302 -49 +302
CR [° F] -40 +212 -40 +212
FKM [° F] -4 +356 -4 +356
Type 484

NBR [° F] -13 +230 -13 +230

FFKM [° F] +32 +482 +32 +482

*)
The temperature is limited by the soft seal material. Refer to table “Soft seal selection” on page 99/11.

04/08 LWN 483.01-E

Type 484
Dimensions – Bestseller For shortest delivery time please select bestsellers. The speciefied
bestsellers can vary depending on different market requirements.

For further available connections please refer to page 04/12.

Metric Units
Actual Orifice diameter d0 [mm] 13 25
Actual Orifice area A0 [mm2] 133 491
Vessel connections
Vessel wall thickness Vessel wall thickness
≤ 5 mm > 5 mm ≤ 5 mm > 5 mm
Flange C [mm] 12,0 12,0 12,0 12,0
thickness C1 [mm] 5,0 18,0 5,0 18,0
Diameter D [mm] 130,0 130,0 150,0 150,0
D1 [mm] 110,0 110,0 127,0 127,0
Bolt circle L [mm] 90,0 90,0 110,0 110,0
Inlet a Inlet a
Welded connections Outlet b Outlet b
(without vessel connection) (without vessel connection)
00: Butt-welded end 25 40
Option code A85L83A16 A85L83A17
Center to face [mm] 24 80,0 30,0 90,0
Height – H4 H max. [mm] 201 298
Inlet a Inlet a
Threaded connections Outlet b Outlet b
(without vessel connection) (without vessel connection)
GD 25 40
Option code
A85H61A16 A85H61A17
(DIN 11850 / DIN 11866 Range A)
Option code
A86H61A16 A86H61A17
(DIN EN ISO 1127 / DIN 11866 Range B)
Center to face [mm] 24 120 30,0 130
Height – H4 H max. [mm] 201 298

US Units
Actual Orifice diameter d0 [inch] 0,512 0,984
2
Actual Orifice area A0 [inch ] 0,206 0,761
Vessel connections
Vessel wall thickness Vessel wall thickness
≤ 13/64 inch > 13/64 inch ≤ 13/64 inch > 13/64 inch
15 15 15 15
Flange C [inch] /32 /32 /32 /32
thickness C1 [inch] 3
/16 23
/32 3
/16 23
/32
Diameter D [inch] 5 1/8 5 1/8 5 29/32 5 29/32
D1 [inch] 4 11/32 4 11/32 5 5

Type 484
Bolt circle L [inch] 3 17/32 3 17/32 4 11/32 4 11/32
Inlet a Inlet a
Welded connections Outlet b Outlet b
(without vessel connection) (without vessel connection)
00: Butt-welded end 25 40
Option code A85L83A16 A85L83A17
15
Center to face [inch] /16 3 5/32 1 3/16 3 17/32
Height – H4 H max. [inch] 7 29/32 11 3/8
Inlet a Inlet a
Threaded connections Outlet b Outlet b
(without vessel connection) (without vessel connection)
GD 25 40
Option code
A85H61A16 A85H61A17
(DIN 11850 / DIN 11866 Range A)
Option code
A86H61A16 A86H61A17
(DIN EN ISO 1127 / DIN 11866 Range B)
15 23 3
Center to face [inch] /16 4 /32 1 /16 5 3/32
Height – H4 H max. [inch] 7 29/32 11 3/8

D1 D1

C C
C1 C1
L L
D D

Type 484 – Gastight cap H2 Type 5034 – Vessel connection

LWN 483.01-E 04/09
 Type 484
Dimensions and weights

Metric Units
Actual Orifice diameter d0 [mm] 13 25
Actual Orifice area A0 [mm2] 133 491
Vessel connections
Vessel wall thickness Vessel wall thickness
≤ 5 mm > 5 mm ≤ 5 mm > 5 mm
PN 16 16 16 16
Flange C [mm] 12,0 12,0 12,0 12,0
thickness C1 [mm] 5,0 18,0 5,0 18,0
Diameter D [mm] 130,0 130,0 150,0 150,0
D1 [mm] 110,0 110,0 127,0 127,0
Bolt circle L [mm] 90,0 90,0 110,0 110,0
Inlet a Inlet a
Welded connections Outlet b Outlet b
(without vessel connection) (without vessel connection)
PN 16 16 16 16
Center to face [mm] 24 80 30 90
Height – H4 H max. [mm] 201 289
Height – H8
double piston design H max.
[mm] 229 296

Inlet a Inlet a
Clamp connections Outlet b Outlet b
(without vessel connection) (without vessel connection)
PN 16 16 16 16
Center to face [mm] 24 102 30 112
Clamp diameter dinner [mm] For varying clamp diameters For varying clamp diameters
douter [mm] please refer to page 00/11 please refer to page 00/11
Height – H4 H max. [mm] 201 289
Height – H8
double piston design H max.
[mm] 229 296

Inlet a Inlet a
Threaded connections Outlet b Outlet b
(without vessel connection) (without vessel connection)
PN 16 16 16 16
Center to face [mm] 24 120 30 130
Height – H4 H max. [mm] 201 289
Height – H8
double piston design H max.
[mm] 229 296

Inlet a Inlet a
Type 484

Flanged connections Outlet b Outlet b

(without vessel connection) (without vessel connection)
PN 16 16 16 16
Center to face [mm] 24 126 30 134
Height – H4 H max. [mm] 201 289
Height – H8
double piston design H max.
[mm] 229 296

Weight
Weight max. [kg] 3,0 4,0

D1

C
C1
L
D
douter
dinner
D1

C
C1
L
D

Type 484 – Cap H2 Type 5034 – Vessel connection Tube end

04/10 LWN 483.01-E
 Type 484
Option codes for available connections For detailed information about the available connections
please refer to “How to use” on page 00/07

Connections
d0 [mm] 13 25
d0 [inch] 0,512 0,984
Clamps Option code inlet Option code outlet
DN 25 40
SO L86A16 L86A17
For inlet please select vessel connection DO I74A16 I74A17
For dimensions Type 5034 as shown on page 04/07.
NPS 1 1/2" 2"
refer to page 00/07 For connections directly machined into vessel
wall please ask for drawing. BO I76A80 I76A81
CO L97A80 L97A81
Threaded connections Option code inlet Option code outlet
Pipe standard DN 25 40
00 A85L83A16 A85L83A17
GS A85H35A16 A85H35A17
BS A85H37A16 A85H37A17

DIN 11850 / GT A85H55A16 A85H55A17

DIN 11866 BT A85H57A16 A85H57A17
Range A GO A85L81A16 A85L81A17
KO A85L82A16 A85L82A17
GD A85H61A16 A85H61A17
BD A85H59A16 A85H59A17
Pipe standard DN 25 40
GS A86H35A16 A86H35A17
BS A86H37A16 A86H37A17
DIN EN
ISO 1127 / GT A86H55A16 A86H55A17
DIN 11866 BT A86H57A16 A86H57A17
Range B GD A86H61A16 A86H61A17
BD A86H59A16 A86H59A17
Pipe standard NPS 1 1/2" 2"
GS A84H35A80 A84H35A81
BS 4825-1 BS A84H37A80 A84H37A81
DIN 11866
GT A84H55A80 A84H55A81
Range C
Type 484

BT A84H57A80 A84H57A81
Flange connections Option code inlet Option code outlet
Pipe standard DN 25 40
NF A85H72A16 A85H72A17
BF A85H74A16 A85H74A17

DIN 11850 / NG A85H76A16 A85H76A17

DIN 11866 BG A85H78A16 A85H78A17
Range A TN A85L84A16 A85L84A17
AF A85L91A16 A85L91A17
AN A85L93A16 A85L93A17
Pipe standard DN 25 40
NF A86H72A16 A86H72A17
DIN EN
ISO 1127 / BF A86H74A16 A86H74A17
DIN 11866 NG A86H76A16 A86H76A17
Range B BG A86H78A16 A86H78A17
Pipe standard NPS 1 1/2" 2"
NF A84H72A80 A84H72A81
BS 4825-1 BF A84H74A80 A84H74A81
DIN 11866
NG A84H76A80 A84H76A81
Range C
BG A84H78A80 A84H78A81

04/12 LWN 483.01-E

Type 484
Surface quality

Surface quality
LESER Surface package
Clean finish HyClean finish Sterile finish
Type of Area
Option code B56 B57 B58
surface
Description No. Ra max. Ra max. Ra max.
LESER Surface grade
ME4 ME2 ME1
Inlet 1 [µm] 0,750 0,500 0,375
Product [µinch] 30 20 15
contact
surface ME4 ME2 ME1
Bottom side
2 [µm] 0,750 0,500 0,375
of disc
[µinch] 30 20 15
ME4 ME3 ME2
Inside surface of outlet
3 [µm] 0,750 0,625 0,500
area
Blow off [µinch] 30 25 20
surface ME6 ME5 ME4
Welding seam 4 [µm] 3,000 1,500 0,750
[µinch] 120 60 30
Outside ME5 ME4 ME4
Outer surface of body,
surface
5 [µm] 1,500 0,750 0,750
bonnet and cap/
lifting device [µinch] 60 30 30
Surface never
in contact with the
Shielded
surface product because it is 6 No definition
shielded by
the bellows

Type 5034 Vessel connection

LESER Surface package
Clean finish HyClean finish Sterile finish
Type of Area
Option code B59 B60 B61
surface
Description No. Ra max. Ra max. Ra max.

Type 484
LESER Surface grade
Product M4 M2 M1
contact Vessel side 7 [µm] 0,750 0,500 0,375
surface [µinch] 30 20 15
M5 M4 M4
Outer
Outside surface 8 [µm] 1,500 0,750 0,750
surface
[µinch] 60 30 30

Caution: Electropolishing of the vessel connection is not reasonable before welding.

If required surface deviates from standard clean finish please specify option code and required LESER Surface package.

3 5

7 1 2

LWN 483.01-E 04/15

Type 484
Approvals

Approvals
Actual Orifice diameter d0 [mm] 13 25
2
Actual Orifice area A0 [mm ] 133 491
Actual Orifice diameter d0 [inch] 0,512 0,984
Actual Orifice area A0 [inch2] 0,206 0,761
Europe Coefficient of discharge Kdr
DIN EN ISO 4126-1 Approval No. 07 202 0111 Z 0008/0/20
S/G 0,60 0,41
L 0,40 0,28
Germany Coefficient of discharge α w
AD 2000-Merkblatt A2 Approval No. TÜV SV 1047
S/G 0,60 0,41
L 0,40 0,28
United States Coefficient of discharge K
ASME Sec. VIII Approval No. M37145 M37167
Rated slope acc. to ASME VIII, Div. 1 UG-131 (d) (2) Rated slope acc. to ASME VIII, Div. 1 UG-131 (d) (2)
S/G S: 5,52 lb / hr / psia  K ≈ 0,521 S: 13,97 lb / hr / psia  K ≈ 0,357
G: 1,96 SCFM / psia  K ≈ 0,521 G: 4,96 SCFM / psia  K ≈ 0,357
Approval No. M37156 M37178
Rated slope acc. to ASME VIII, Div. 1 UG-131 (d) (2) Rated slope acc. to ASME VIII, Div. 1 UG-131 (d) (2)
L
L: 2,96 GPM √psid*)  K ≈ 0,379 L: 7,46 GPM √psid*)  K ≈ 0,258
Canada Coefficient of discharge K
CRN Approval No. OG0772.9C
Rated slope acc. to ASME VIII, Div. 1 UG-131 (d) (2) Rated slope acc. to ASME VIII, Div. 1 UG-131 (d) (2)
S/G S: 5,52 lb / hr / psia  K ≈ 0,521 S: 13,97 lb / hr / psia  K ≈ 0,357
G: 1,96 SCFM / psia  K ≈ 0,521 G: 4,96 SCFM / psia  K ≈ 0,357

Rated slope acc. to ASME VIII, Div. 1 UG-131 (d) (2) Rated slope acc. to ASME VIII, Div. 1 UG-131 (d) (2)
L
L: 2,96 GPM √psid*)  K ≈ 0,379 L: 7,46 GPM √psid*)  K ≈ 0,258

Type 484
China Coefficient of discharge α w
AQSIQ Approval No. 02301T
S/G 0,60 0,41
L 0,40 0,28
Russia Coefficient of discharge α w
GGTN/
GOSGORTECHNADZOR
Approval No. PPC00-18458

GOST R Approval No. 1989-06

S/G 0,60 0,41
L 0,40 0,28
Belarus Coefficient of discharge α w
PROMATOMNADZOR Approval No. 15-171-2006
S/G 0,60 0,41
L 0,40 0,28
Classification societies
on request

*) psid = Differential pressure P-Pd

P = absolute flow pressure [psia]
Pd = pressure at discharge from valve [psia]

LWN 483.01-E 04/17

 Type 484
Capacities – Metric Units
Capacities for saturated steam, air at 0° C and 1013 mbar, water at 20° C according to AD 2000-Merkblatt A2, based on set pressure plus 10 % overpressure.
Capacities at 1 bar (14,5 psig) and below are based on 0,1 bar (1,45 psig) overpressure. For pressure range refer to “Pressure temperature ratings” on page 04/08.

Steam AD 2000-Merkblatt A2 [kg/h]

Actual Orifice diameter d0 [mm] 13 25
Actual Orifice area A0 [mm2] 133 491 2.500
LEOS/G*) [inch2] 0,110 0,279
Set pressure [bar] Capacities [kg/h] d0 25
2.000
1 88 213
2 142 347
3 191 472 1.500
4 239 603

Discharge capacity [kg/h]

Maximum temperature for EPDM soft seal
5 286 722 1.000
d0 13
6 332 840
7 378 956
500
8 425 1073
9 471 1191
10 518 1308 0
12 611 1543 0 2 4 6 8 10 12 14 16
14 701 1773 Pressure [bar]
16 794 2007

Air AD 2000-Merkblatt A2 [mn3/h]

Actual Orifice diameter d0 [mm] 13 25 3.000
Actual Orifice area A0 [mm2] 133 491
LEOS/G*) [inch2] 0,110 0,279 d0 25
2.500
Set pressure [bar] Capacities [mn3/h]
1 105 254
2 171 418 2.000
3 234 576
Discharge capacity [mn3/h]

4 293 741 1.500

5 353 892
6 413 1043 d0 13
1.000
7 472 1194
8 532 1344
500
9 592 1495
Type 484

10 651 1646
12 771 1947 0
0 2 4 6 8 10 12 14 16
14 890 2249
16 1009 2551 Pressure [bar]

Water AD 2000-Merkblatt A2 [103kg/h]

Actual Orifice diameter d0 [mm] 13 25 30
Actual Orifice area A0 [mm2] 133 491 d0 25
LEOL*) [inch2] 0,082 0,302
25
Set pressure [bar] Capacities [103kg/h]
1 2,83 7,33
2 4,01 10,4 20
Discharge capacity [103kg/h]

3 4,91 12,7
4 5,66 14,7 15
5 6,33 16,4 d0 13
6 6,94 18 10
7 7,49 19,4
8 8,01 20,7 5
9 8,5 22
10 8,96 23,2
12 9,81 25,4 0
0 2 4 6 8 10 12 14 16 18
14 10,6 27,4
16 11,3 29,3 Pressure [bar]

*) LEOS/G/L = LESER Effective Orifice steam/gas/liquids please refer to page 00/17.

04/18 How to use capacity-sheets refer to page 00/15. LWN 483.01-E
Type 484
Available options

Gastight cap H2 Gastight lifting device H4 Pneumatic lifting device H8 Pneumatic lifting device H8
H2 Packed knob H4 H8 single piston design J41: H8 double piston design

O-ring-disc Bellows FFKM “C” Blind flange for pressure test O-ring for vessel connection
J22: EPDM “D” S70 Material-No. 138.8849.9000 (d0 13) EPDM “D”
J21: CR “K” Material-No. 138.8649.9000 (d0 25) Material-No. 502.0460.3041 (d0 13)
J23: FKM “L” Material-No. 502.0600.3041 (d0 25)
J30: NBR “N”
J20: FFKM “C”

Test gag
J70: H2

Type 484
Lift indicator placed in bonnet Special material
J38 + J93 2.4610 HASTELLOY C4
2.4360 MONEL 400
1.4462 DUPLEX

Code
YYYY
Code Code
XXXX ZZZZ

LWN 483.01-E 04/13

Accessories and Options
Soft seal selection

Type 481 – O-ring disc and Type 483, 484, 485, 488 – HyTight Assembly
Type 481 – Vulcanized soft seal disc

Soft seal selection

Abbrevation Trade name Code- Option Tmin Tmax
Application2)
ASTM 1418 (Designation) letter1) Code [° C] [° F] [° C] [° F]
O-ring
Parafin oil, silicone oil and grease, water and
CR Neoprene® K J21 -40 -40 100 212
waterbased solvents, refrigerants, ozone

Buna-N®
NBR (Nitrile-Butadiene) N J30 -25 -13 100 212 Hydraulic oil, vegetable and animal grease and oil

Hot water and superheated steam up to 150° C,

Buna-EP® 302° F, several organic and inorganic acids,
EPDM (Ethylene-Propylene- D J22 -45 -49 150 302
Diene) silicone oil and grease, FDA compliant and
USP VI compliant compound
High temperature service (no superheated steam),
Viton® mineral oil and grease, silicone oil and grease,
FKM L J23 20 -4 180 356
(Fluorocarbon) vegetable and animal grease and oil, ozone,
FDA compliant compound
Nearly all chemicals, standard compound is
Kalrez® Kalrez® 6230 or ISOLAST® J9515, FDA and
FFKM (Perfluoro) C J20 0 32 250 482
USP VI compliant compound
For other materials please contact your
Other than listed X local representative or [email protected]
1)
The code letters will be stamped on the disc.
2)
Pressure and temperature service must be considered in any case.
Chemical resistance and the temperature limits depend on O-ring manufacturer information. LESER can not take any warranty.

Soft seal selection Temperature limits Trademarks Soft seal

Registered trademarks Company
-25° C/ J30 100° C/
-13° F NBR – “N” 212° F
Buna-N®, Viton®,
DuPont
Neoprene®, Kalrez®

-40° C/ J21 100° C/

-40° F 212° F
Buna EP® Bayer
CR – “K”

ISOPLAST® Busak + Shamban

-45° C/ J22 150° C/

-49° F EPDM – “D” 302° F

-20° C/ J23 180° C/

-4° F FKM – “L” 356° F

0° C/ J20 250° C/
32° F FFKM – “C” 482° F
[°F]
-58 -40 -22 -4 14 32 77 122 167 212 257 302 347 392 437 482
Options

-50 -40 -30 -20 -10 0 25 50 75 100 125 150 175 200 225 250
[°C] Temperature t

LWN 483.01-E 99/11