Daniels Manufacturing Corporation offers materials to keep pace with the most recent advances in

our BETA Backshell Assembly Tools, a complete line technology. DMC is ready and capable to help satisfy
of Adaptor Tools and Torque Tools for holding and your tooling needs with custom engineered tools.
torquing circular connectors during the installation DMC’s full-service facility in Orlando, Florida has a
and removal of accessories (backshell, strain relief, qualified staff to recalibrate tools to meet FAA requirements
or EMI/RFI shielding hardware). and to refurbish Adaptor Tool Kits. DMC has developed
With over seven decades of industry experience, DMC is a worldwide network of professionals who can assist
the leading manufacturer of Mil-Qualified Crimp Termination in answering technical questions, processing orders for
Tools, Maintenance Tool Kits, and Insertion/Removal Tools complete kits and individual components, designing
for the High-Reliability Wire Harness Industry. DMC also new service kits, and modifying existing kits.
manufactures ALPHATRON Wire Crimp Pull Testers
and SAFE-T-CABLE, the time-saving substitute for safety DMC is an ISO 9100:2015 and AS9100D Registered
Lockwire. DMC products have been used on virtually every Company, and RoHS Compliant.
Defense System, Aircraft Program, Land or Sea Going
Transport System, and Space Exploration Program.
DMC is continually working with the government and
major manufacturers toward the development of support

PAGE 4 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 CONTENTS
Adaptor Tools Introduction ................. 2
BETA System Utilization ..................... 4
Connector Technical Data
Pages & Adaptor Tool
Selection Guide .................................. 6
Connector Identification .................... 33
Connector Mate Assembly Vise ........ 38
Torque Tools .................................... 40
Strap Wrenches................................ 42
Torque Conversion Formula.............. 46
Torque Conversion Charts ............... 47
General Purpose Backshell/
Accessory Tools ............................... 47
Jam Nut Sockets ............................. 48
Circular Ring and Soft-Jaw Pliers ..... 51
EMI/RFI Banding Tools ..................... 52
BETA Tool Kits ................................. 56
Connector Accessory Guide ............. 58
Suggested Torque Values ................ 63
National Stock Numbers
for Beta Series Tooling ..................... 65
Warranty .......................................... 66
Other DMC Products ....................... 67

IMPORTANT NOTICE
The tooling suggested herein may
not cover a user’s specific contract
or manufacturing require­­­ments. It is
the user’s responsibility to carry out
sufficient testing to verify the suitability
of the DMC product selected for the
specific requirements of each particular
application. DMC is not liable for
consequential or special damages of any
nature or kind resulting from the use of
any of our products.
Verbally quoted prices, or any prices,
appearing in printed price lists, are subject
to change without prior notice.
If you need firm prices for future
deliveries, you should request a written
quotation from our sales office.

LIMITED WARRANTY
SEE INSIDE BACK COVER

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • FAX 407-855-6884 • WWW.DMCTOOLS.COM PAGE 1
© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 1
ADAPTOR TOOLS

mizing the tool requirements for surface area and over a larger portion
­overall system support. Many other of the circumference of the connector.
important benefits are designed into
DMC Beta adaptor tools. ADAPTORS ARE AVAILABLE
FOR BOTH PLUGS AND
SINGLE TOOL FOR MULTIPLE RECEPTACLES
KEYING POSITIONS The rotating coupling mechanism
When multiple keying positions exist found on most plug connectors is
within a specific shell size (Diameter), the primary factor which prompted
DMC engineers have designed the original adaptor tool design;
The central element of the Daniels each adaptor tool to accommodate however, many users currently realize
Manufacturing Corp. Beta connector as many variations as possible. the benefits of adaptor tools when
accessory tool product line is the Most adaptors will mate with six or assembling or servicing receptacle
adaptor tool. This unique device is more connectors having different connectors. DMC has
configured in such a manner as to keying positions. When c ­ ompared both versions available for most
mate perfectly with the corresponding with dummy receptacles or other circular connector series.
circular connector keying pattern. connector holding devices, this
Therefore, it can be used to hold the flexibility is not possible. STANDARD SQUARE
connector in a stationary position DRIVE MOUNTING
while the accessory components are MULTIPLE KEY ENGAGEMENT All DMC adaptor tools are
being installed or removed. Many The critical platings and delicate made with a standard square
­keying arrangements and shell sizes nature of connector keys are a prime drive (either 3/8" or 1/4") socket
are utilized in high reliability wiring consideration in the design of a secure for easy utilization with common
­systems and great care must be connector holding system. Therefore, torque measuring devices or other
­exercised when selecting and using in all cases where the basic connector tooling. This eliminates the need
the Beta adaptor tool. DMC has configuration permits, multiple key for special mounting fixtures, or
made great efforts to combine the engagement is utilized. This allows other considerations common to
most possible applications into each torque to be applied to a greater the use of dummy r­eceptacles and
adaptor tool design, thereby mini­ similar equipment.

CIRCULAR CONNECTORS AND performance capabilities. This

THEIR ACCESSORIES variety of products offers the
The evolution of electrical equipment designer total flexibility
connectors has seen many changes in the packaging of electronic
in design configuration and utilization wiring systems.
of many varieties of materials to In the past two decades special
meet the needs of their intended considerations such as the shielding
application. Backshells, strain reliefs, of electrical circuits from interference
and other connector accessories generated by radar systems, com­
have been a vital factor in that munication equipment, electrical
enduring evolutionary process. fields, nuclear fields and harsh
Most connector manufacturers ­environmental conditions, have
and suppliers offer a limited variety required accessory suppliers to
of connector accessories. But, the ­develop multi-piece components
specific needs of aerospace designers which have very specific assembly
has fostered a connector accessory and maintenance requirements.
industry comprised of many dynamic The demand for advanced tool
manufacturers, with extensive product ­capabilities is a critical element in
lines dedicated solely to components the utilization of these sophisticated
which extend the connector’s backshell systems.

PAGE 2 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 QUICK REFERENCE TOOLING GUIDE
SIMPLE ORIENTATION
CONNECTOR ADAPTOR TOOL SETS ADAPTOR
PAGE TO THE CONNECTOR
INDENTIFICATION PLUG RECEPTACLE LABEL
All adaptor tools have an indicator
AS50151 (MIL-C-5015) CM-S-5015 CM-S-5015R CHROME 6 (dot) which visually orients it with the
MIL-DTL-22992 CLASS C,J,R CM-S-229 N/A BROWN 7 master key on the connector. This
MIL-DTL-22992 CLASS L CM-S-229L N/A BLACK 8
enables the user to orient the two
components for mating without trial
MIL-DTL-26482 SERIES I & II CM-S-264 CM-S-264R ORANGE 9
and error fumbling.
MIL-DTL-26500 CM-S-837 CM-S-837RB* GREEN 10

MIL-DTL-28840 CM-S-288 CM-S-288R WHITE 11 ECONOMICAL, RELIABLE,

MIL-DTL-38999 SERIES I CM-S-389L CM-S-389LR BLUE 12 AND AVAILABLE
MIL-DTL-38999 SERIES II CM-S-389S CM-S-264R GRAY/ORANGE 13 There is not a precision system for
holding circular connectors a ­ vailable
MIL-DTL-38999 SERIES III CM-S-389T CM-S-389TR LAVENDER 14
anywhere which is more economical,
MIL-DTL-38999 SERIES IV CM-S-389B CM-S-389BR BEIGE 15
reliable, or readily available to meet
MIL-C-81511 SERIES I & III CM-S-815L CM-S-815R YELLOW 16 your needs than the DMC Beta
MIL-C-81511 SERIES II & IV CM-S-815S CM-S-815R RED 17 adaptor tools.
MIL-DTL-83723 SERIES I CM-S-264 CM-S-264R ORANGE 18

MIL-DTL-83723 SERIES II CM-S-5015 CM-S-5015R CHROME 19

MIL-DTL-83723 SERIES III* CM-S-837 CM-S-837RB* GREEN 20

PATTERN 602 CM-S-602 CM-S-264R PURPLE 21

PATTERN 615 CM-S-SJT CM-S-264R GOLD 22

2M801/801 CM-S-801 CM-S-801R N/A 23

2M803/803 CM-S-803 CM-S-803R N/A 26 Receptacle Plug

2M804/804 CM-S-804 CM-S-804R N/A 28

2M805/805 CM-S-805 CM-S-805R N/A 31 Typical Mated Pair Connectors

*BAYONET COUPLINGS ONLY – THREADED RECEPTACLE ADAPTOR SETS ARE NOT AVAILABLE FOR RECEPTACLE
MATERIAL: ALUMINUM - STEEL TOOLING IS AVAILABLE. CHECK WITH DMC FOR DETAILS.

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 3
ADAPTOR TOOLS

Adaptor tools and other accessory tools which comprise the DMC BETA™
product line are used in a variety of combinations to afford the user an efficient
and flexible system of connector/accessory assembly. The following illustrations
depict a few of the products which are combined in use. Certainly there are many
applications which are not described. The selection of tools and the ways in which
they are used are both dependent upon the types of connectors and accessory
components as well as production and quality considerations. DMC will help with
any application questions you may have.

NOTE: Rotating the connector is not recommended — due to the stress which
it imposes on the wire, contacts and sealing components. Adaptors and their
associated tools that are designed to hold the connector stationary while the
backshell accessory is turned.

SIMPLE HAND TIGHTENING SIMPLE MECHANICAL ASSIST

In the most basic operation, the When mechanical assistance is Other tools, such as circular ring
adaptor is mated with the connector, necessary to sufficiently tighten the pliers or a strap wrench, could also
and held in one hand. This stabilizes accessory onto the connector, the have been selected to add simple
the connector while the backshell stabilizing effect of the adaptor can mechanical assistance.
accessory is tightened with the other be reinforced with one of several
hand. tools — in the operation shown, the
connector is held stationary by the
use of a “T” handle in the drive hole
of the adaptor, while soft jaw pliers
are being used on the accessory.

Strain relief, connector, adaptor Soft jaw pliers, strain relief, connector, Circular Ring Pliers, strain relief,
adaptor, T-handle connector, adaptor, T-handle

Strain relief, connector, adaptor Soft jaw pliers, strain relief, connector, Strap wrench, strain relief, connector
adaptor, T-handle

PAGE 4 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 PRODUCTION STATION APPLICATIONS

When the measurement of torque On multi-piece backshells, the

is a requirement of a particular cable correct torque on each accessory
assembly operation, this can be can only be achieved by efficiently
easily accomplished with the use of holding adjacent parts. In the
example shown, the assembly
the digital torque wrench.
station vise is being used to hold
the backshell segment already
Stationary torque meter,
torqued onto the connector, while
adaptor tool, connector, strain
relief, strap wrench the strain relief is tightened with a
strap wrench and a torque wrench.
Thus, the correct torque can be
applied to the backshell segments
without affecting the torque value
already applied to prior connector/
accessory components.
Digital torque wrench, adaptor,
connector, strap wrench Stationary torque meter,
adaptor tool, connector,
strain relief, strap wrench

Digital torque wrench,

handle-less strap wrench,
strain relief, backshell &
When optimum repeatability and connector (in vise), vise
production efficiency demand, the
assembly station vise can be used
to complement the ability of adaptor
Digital torque wrench, strap wrench, tools to stabilize the connector.
connector, vise As shown, the vise is being used
to firmly hold the adaptor tool,
while a strap wrench is being used
to tighten the backshell onto the
connector.
If a stationary torque meter is
needed, the digital torque wrench
can be placed in a stationary mount
base. The adaptor is then attached
to the square drive on the torque
meter, and this arrangement holds
the connector while the backshell Strap wrench,
accessory is torqued onto the backshell, connector,
adaptor, vise
connector, with a strap wrench.
When the torque reaches the
pre-set value, a signal light advises
the operator that the desired torque
value has been applied.

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 5
AS50151
SERIES MS3100, MS3400 & MS3450
MANUFACTURER: SERIES:
AERO ELECTRIC AE501, AE55, AE502, AE723
AMPHENOL 69, 72, 97, 157, 172, 173, 179, 208, 238 246
BT-M, BT-RA, HT, SCP, TBF, 10-72, 10-214, 10-244, 10-741,
10-747, 10-873, 10-874, 5015
AMPHENOL/MATRIX MFR, M723, 944, 981
GLASSEAL GSP
HERMETIC SEAL CORP. HS06, S*A-2000, 2000
ITT CANNON BFH, BFR, CA, CA-EA, CA-EB, CA-HR, CA-KE, CA-RX, CV,
CVA, EX-A, FRA, FRF, FVA, FVF, FW, GS, MR, TBF, TBFH, WFS
ARRAY AC
SPACECRAFT RJ, SC
GLENAIR 650B, 660
Straight Plug Shown CORSAIR CJ
ELECSYS D, DJ, DS, L, W, U
J-TECH D, DJ, DS, DJS, W, L, U, JT

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: THREADED (MS3107,
SHELL FINISH
MS3507 QUICK
ALUMINUM Cadmium Olive Drab
DISCONNECT) Nickel
KEYING POSITIONS: BLANK (NORMAL), Cadmium Olive Drab Over Nickel
W, X, Y, Z WROUGHT ALUMINUM Cadmium Olive Drab Over Nickel
ALTERNATE KEYING ROTATION OF INSERT STEEL Cadmium Olive Drab
METHOD: WITHIN SHELL – KEY Nickel
REMAINS STATIONARY STAINLESS STEEL Cadmium Black
EMI/RFI GROUNDING: NO Passivated

MS 3400 D 18 10 P W
MILITARY PREFIX KEYING POSITION
SHELL STYLE CONTACT TYPE (PIN OR SOCKET)
SERVICE CLASS INSERT ARRANGEMENT
SHELL SIZE

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR BASIC IDENT. #/DESCRIPTION
SIZE POSITIONS NUMBER COLOR
MS3106/Straight 8 ALL CM5015-8 CHROME MS3100/Wall mount 8 ALL CM5015R-8 CHROME
MS3107/ Quick disconnect 10 ALL CM5015-10 CHROME MS3101/ In-line 10 ALL CM5015R-10 CHROME
MS3108/ 90º angle MS3102/ Box mount
MS3436/ Straight 12 ALL CM5015-12 CHROME MS3103/ Wall mount, 12 ALL CM5015R-12 CHROME
MS3507/ Quick disconnect potting seal
14 ALL CM5015-14 CHROME 14 ALL CM5015R-14 CHROME
MS25183/ Straight, potting seal MS3142/ Box mount,
16 ALL CM5015-16 CHROME hermetic seal 16 ALL CM5015R-16 CHROME
MS25183A/ Straight, potting
seal, with ground lug MS3143/ Solder mount,
18 ALL CM5015-18 CHROME hermetic seal 18 ALL CM5015R-18 CHROME
MS3406/ Straight
MS3400/ Wall mount
MS3408/ 90º angle 20 ALL CM5015-20 CHROME 20 ALL CM5015R-20 CHROME
MS3401/ In-line
MS3409/ 45º angle
22 ALL CM5015-22 CHROME MS3402/ Box mount 22 ALL CM5015R-22 CHROME
MS3456/ Straight
MS3404/ *Jam nut
MS3459/ Straight self-locking 24 ALL CM5015-24 CHROME 24 ALL CM5015R-24 CHROME
coupling nut MS3412/ Box mount,
28 ALL CM5015-28 CHROME threaded rear skirt 28 ALL CM5015R-28 CHROME
MS3450/ Wall mount
32 ALL CM5015-32 CHROME MS3451/ In-line 32 ALL CM5015R-32 CHROME

36 ALL CM5015-36 CHROME MS3452/ Box mount 36 ALL CM5015R-36 CHROME

MS3454/ *Jam nut
40 ALL CM5015-40 CHROME 40 ALL CM5015R-40 CHROME

44 ALL CM5015-44 CHROME *Consult DMC for “SL” Series. 44 ALL CM5015R-44 CHROME

48 ALL CM5015-48 CHROME 48 ALL CM5015R-48 CHROME

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-5015 15 8 THRU 48 CM-S-5015R 15 8 THRU 48

CM-S-5015S 10 8 THRU 28 CM-S-5015RS 10 8 THRU 28
CM-S-5015M 5 32 THRU 48 CM-S-5015RM 5 32 THRU 48

PAGE 6 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MIL-DTL-22992
CLASS C, J & R
MANUFACTURER: SERIES:
AMPHENOL HK, QWLD (10-194), 88-194

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: QUICK DISCONNECT –
SHELL FINISH
THREADED COUPLING
ALUMINUM Hard Black Anodize
RINGS Cadmium Olive Drab Over Nickel
KEYING POSITIONS: BLANK (NORMAL),
W, X, Y, Z
ALTERNATE KEYING ROTATION OF INSERT
METHOD:  WITHIN SHELL – KEYS
REMAIN STATIONARY
Plug Shown EMI/RFI GROUNDING: NO

TYPICAL CONNECTOR
PART NUMBER
MS 17345 C 28 N 15 P X
BREAKDOWN MILITARY PREFIX KEYING POSITION
SHELL STYLE CONTACT TYPE (PIN OR SOCKET)
CLASS INSERT ARRANGEMENT
SHELL SIZE FINISH

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION BASIC IDENT. #/DESCRIPTION
SIZE POSITIONS NUMBER COLOR SIZE POSITIONS NUMBER COLOR

MS17344/Plug 12 ALL CM229-12 BROWN 12 – N/A –

MS17343 /Wall mount
14 ALL CM229-14 BROWN MS17345/ In-line 14 – N/A –
MS17346/ Box mount
16 ALL CM229-16 BROWN 16 – N/A –
MS17347/ Jam nut wall mount
18 ALL CM229-18 BROWN MS17348 / Jam nut box mount 18 – N/A –

20 ALL CM229-20 BROWN 20 – N/A –

22 ALL CM229-22 BROWN 22 – N/A –

24 ALL CM229-24 BROWN 24 – N/A –

36 ALL CM229-36 BROWN 32 – N/A –

40 ALL CM229-40 BROWN 36 – N/A –

40 – N/A –

NOTE: For shell sizes 28, 32, 44 see Class “L”, Page 8. NA (Not available)

ADAPTOR SET PART NO.* ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO.** ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-229 9 12 THRU 40 N/A – –

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 7
MIL-DTL-22992
CLASS L
MANUFACTURER: SERIES:
AMPHENOL ALQWLD, 229, 10-473, MHD
ROBERT TECHNOLOGIES RT905

COUPLING METHOD: QUICK DISCONNECT – SHELL MATERIAL & FINISH:

THREADED COUPLING
SHELL FINISH
RINGS
ALUMINUM Hard Black Anodize
KEYING POSITIONS: N (NORMAL), W, X, Y Cadmium Olive Drab Over Nickel
ALTERNATE KEYING ROTATION OF INSERT
METHOD:  WITHIN SHELL – KEYS
REMAIN STATIONARY
Straight Plug Shown EMI/RFI GROUNDING: NO

TYPICAL CONNECTOR
PART NUMBER
MS 90556 C 44 N 01 P N
BREAKDOWN MILITARY PREFIX ALTERNATE INSERT POSITION
SHELL STYLE CONTACT TYPE (PIN OR SOCKET)
FINISH INSERT ARRANGEMENT
SHELL SIZE MASTER KEY/KEYWAY POSITION

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION BASIC IDENT. #/DESCRIPTION
SIZE POSITIONS NUMBER COLOR SIZE POSITIONS NUMBER COLOR

MS90556/Straight 28 ALL CM229L-28 BLACK MS90555/Wall mount 28 – N/A –

MS90558/ Wall mount 32 ALL CM229L-32 BLACK MS90557/ In-line 32 – N/A –

44 ALL CM229L-44 BLACK 44 – N/A –

48 ALL CM229L-48 BLACK 48 – N/A –

52 ALL CM229L-52 BLACK 52 – N/A –

NA (Not available)

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-229L 5 28 THRU 52 N/A – –

PAGE 8 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MIL-DTL-26482
SERIES I & II
MANUFACTURER: SERIES:
ARRAY PW
AERO ELECTRIC AE77
AMPHENOL 118, DC, FPT(21-), PT, PT*CE, SP*CE, PT*SE, PTS*DR, SP, MB1
DEUTSCH/TE AFD, DBC, RBC, 226,450, 460, 810, 880
GLASSEAL BE, GB
HERMETIC SEAL CORP. S*A-7000, 7000, HR
ITT CANNON KPD, KPSE, KSSE, KP*, KS*, KPT, KSP, KPTM, KSPM PV, PVA,
PVJ, PVW, PVX
SEALTRON 6300, 8100, 8300, 8312, 8315
SOURIAU 851, 851*R, 8526, BT, L*T
SPI MS31
CORSAIR CJO
Straight Plug Shown
SPECIFICATIONS: SHELL MATERIAL & FINISH:
COUPLING METHOD: BAYONET
SHELL FINISH
KEYING POSITIONS: BLANK (NORMAL),
ALUMINUM Hard Anodize – Gray/Black
W, X, Y, Z Cadmium Olive Drab
ALTERNATE KEYING ROTATION OF INSERT Cadmium Olive Drab Over Nickel
METHOD: KEYS REMAIN STATIONARY STEEL Tin
EMI/RFI GROUNDING: YES (EMI/RFI GROUNDING
FINGERS MAY NOT BE
AVAILABLE ON ALL M
­ ODELS)

TYPICAL CONNECTOR
PART NUMBER
MS 3114 E 12 C 10 P W
BREAKDOWN MILITARY PREFIX KEYING POSITION
SHELL STYLE CONTACT TYPE (PIN OR SOCKET)
CLASS INSERT ARRANGEMENT
SHELL SIZE TERMINATION TYPE/SHELL MATERIAL (HERMETIC RECEPTACLES ONLY)

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR
MS3110/Wall mount
MS3116/Straight 8 ALL CM264-8 ORANGE 8 ALL CM264R-8 ORANGE
MS3111/In-line
MS3126/Straight 10 ALL CM264-10 ORANGE MS3112 /Box mount 10 ALL CM264R-10 ORANGE
MS3475/Straight, RFI grounding MS3113/Hermetic seal solder mount
MS3476/Straight 12 ALL CM264-12 ORANGE 12 ALL CM264R-12 ORANGE
MS3114/Jam nut
14 ALL CM264-14 ORANGE MS3119/Thru-bulkhead 14 ALL CM264R-14 ORANGE
MS3120/Wall mount
16 ALL CM264-16 ORANGE 16 ALL CM264R-16 ORANGE
MS3121/In-line
18 ALL CM264-18 ORANGE MS3122 /Box mount 18 ALL CM264R-18 ORANGE
MS3124/Jam nut
20 ALL CM264-20 ORANGE 20 ALL CM264R-20 ORANGE
MS3127/Large flange box mount
22 ALL CM264-22 ORANGE MS3128 /Large flange wall mount 22 ALL CM264R-22 ORANGE
MS3440/Hermetic seal box mount
24 ALL CM264-24 ORANGE 24 ALL CM264R-24 ORANGE
MS3442/Wide flange hermetic seal
box mount
MS3443/Hermetic seal solder mount
MS3449/Hermetic seal jam nut
MS3470/Wall mount
MS3471/In-line
MS3472 /Wide flange wall mount
MS3473/Hermetic seal solder mount
MS3474 /Jam nut
MS3477/Hermetic seal box mount
MS3479/Hermetic seal jam nut

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-264 9 8 THRU 24 CM-S-264R 9 8 THRU 24

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 9
MIL-DTL-26500

MANUFACTURER: SERIES:
AMPHENOL 48, 48-7005, 518, MB3, MT3, B, BFH, F, ZZ
BOEING (SPECIFICATION) BACC45F, BACC63
CONNECTOR INDUSTRIES 26500
DETORONICS DX
Deutsch/TE DB, DL, 94603
ELECTRONIC SEALS 26500
GLASSEAL 50
HERMETIC SEAL CORP. 26500
ITT CANNON HTMF
SEALTRON 6500, 6600, 8500, 8600
SOURIAU 8530
CINCH C48, CN0915, CN0930, CN0942, CN0966, CN0967, MMB

Straight Plug Shown

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: BAYONET OR THREADED
KEYING POSITIONS: N (NORMAL), 1, 2, 3, 4, 5, SHELL FINISH
6, 7, 8, 9, 10 ALUMINUM Anodize – Gray/Black
Cadmium
ALTERNATE KEYING INSERT ROTATION IN
METHOD: POSITIONS 1 THRU 5, STAINLESS STEEL Passivated
MINOR KEYS ROTATE IN STEEL Tin
POSITIONS 6 THRU 10 Cadmium
EMI/RFI GROUNDING: NO

TYPICAL CONNECTOR
PART NUMBER
MS 24264 R 18 B 31 P 6 H
BREAKDOWN MILITARY PREFIX CABLE SUPPORT
SHELL STYLE KEYING POSITION
CLASS CONTACT TYPE (PIN OR SOCKET)
SHELL SIZE INSERT ARRANGEMENT
COUPLING TYPE (B OR T)

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR

MS24266/Straight 8 N, 8, 9 CM837-8A* GREEN MS24264/Wall mount 8 ALL CM837RB-8 GREEN

MS27615/ Straight 8 6, 7 CM837-8B* GREEN MS24265/ Jam nut 10 ALL CM837RB-10 GREEN
MS27034/ Hermetic solder mount
8 N, 8, 9 CM837-8C** GREEN MS27613/ Wall mount 12 ALL CM837RB-12 GREEN

8 6, 7 CM837-8D** GREEN MS27614/ Jam nut 14 ALL CM837RB-14 GREEN

10 N, 8, 9 CM837-10A GREEN 16 ALL CM837RB-16 GREEN

10 6, 7, 10 CM837-10B GREEN 18 ALL CM837RB-18 GREEN

12 N, 6, 8 CM837-12A GREEN 20 ALL CM837RB-20 GREEN

12 7, 9, 10 CM837-12B GREEN 22 ALL CM837RB-22 GREEN

14 N, 6, 8 CM837-14A GREEN 24 ALL CM837RB-24 GREEN

14 7, 9, 10 CM837-14B GREEN

16 N, 6, 8 CM837-16A GREEN

16 7, 9, 10 CM837-16B GREEN

18 N, 6, 8 CM837-18A GREEN

18 7, 9, 10 CN837-18B GREEN

20 N, 6, 8 CM837-20A GREEN

20 7, 9, 10 CM837-20B GREEN

22 N, 6, 8 CM837-22A GREEN

22 7, 9, 10 CM837-22B GREEN

24 N, 6, 8 CM837-24A GREEN

24 7, 9, 10 CM837-24B GREEN

28 N, 6, 8 CM837-28A GREEN

28 7, 9, 10 CM837-28B GREEN
*For bayonet coupling connectors only. **For threaded coupling connectors only. Bayonet couplings only. Adaptors not available for connectors with threaded coupling.

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-837 22 8 THRU 28 CM-S-837RB 9 8 THRU 24

PAGE 10 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MIL-DTL-28840

GLENAIR GT, GS, GS28840, 900

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: THREADED
SHELL FINISH
KEYING POSITIONS: 1, 2, 3, 4, 5, 6
ALTERNATE KEYING MASTER KEY REMAINS ALUMINUM Cadmium Olive Drab Over Nickel
METHOD:  STATIONARY – STEEL Cadmium
MINOR KEYS ROTATE
­INDEPENDENTLY
EMI/RFI GROUNDING: YES (EMI/RFI GROUNDING
­FINGERS MAY NOT BE
Straight Plug Shown ­AVAILABLE ON ALL MODELS)

M28840/16
B D 1 C B S 4
MILITARY SPECIFICATION SHEET KEYING POSITION
CLASS CONTACT TYPE (PIN OR SOCKET)
SHELL SIZE BACKSHELL STYLE
INSERT ARRANGEMENT BACKSHELL SIZE

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION BASIC IDENT. #/DESCRIPTION
SIZE POSITIONS NUMBER COLOR SIZE POSITIONS NUMBER COLOR

M28840/16/Straight 11(A) 1, 3, 5 CM288-11A WHITE M28840/10/Wall mount 11(A) 1 CM288R-11A WHITE

M28840/17/ S
 traight, straight 11(A) 2, 4, 6 CM288-11B WHITE M28840/11/ In-line 13(B) 1 CM288R-13A WHITE
strain relief M28840/12/ Box mount
M28840/18/ S traight, 90º 13(B) 1, 3, 5 CM288-13A WHITE M28840/14/ Jam nut 15(C) 1 CM288R-15A WHITE
strain relief
13(B) 2, 4, 6 CM288-13B WHITE M28840/20/ Wall mount, EMI 17(D) 1 CM288R-17A WHITE
M28840/19/ S
 traight, 45º
strain relief M28840/21/ In-line, straight
15(C) 2, 3, 4 CM288-15A WHITE backshell for 19(E) 1 CM288R-19A WHITE
M28840/26/ S traight, straight jacketed cable
­backshell for 15(C) 1, 5, 6 CM288-15B WHITE 23(F) 1 CM288R-23A WHITE
jacketed cable
M28840/28/ S
 traight, 90º 17(D) 2, 3, 4 CM288-17A WHITE 25(G) 1 CM288R-25A WHITE
backshell for
jacketed cable 17(D) 1, 5, 6 CM288-17B WHITE 29(H) 1 CM288R-29A WHITE
M28840/29/ S
 traight, 45º
backshell for 19(E) 2, 3, 4 CM288-19A WHITE 33(J) 1 CM288R-33A WHITE
jacketed cable
19(E) 1, 5, 6 CM288-19B WHITE 11(A) 2, 3, 4, 5, 6 CM288R-11B WHITE

23(F) 2, 3, 4 CM288-23A WHITE 13(B) 2, 3, 4, 5, 6 CM288R-13B WHITE

23(F) 1, 5, 6 CM288-23B WHITE 15(C) 2, 3, 4, 5, 6 CM288R-15B WHITE

25(G) 2, 3, 4 CM288-25A WHITE 17(D) 2, 3, 4, 5, 6 CM288R-17B WHITE

25(G) 1, 5, 6 CM288-25B WHITE 19(E) 2, 3, 4, 5, 6 CM288R-19B WHITE

29(H) 2, 3, 4 CM288-29A WHITE 23(F) 2, 3, 4, 5, 6 CM288R-23B WHITE

29(H) 1, 5, 6 CM288-29B WHITE 25(G) 2, 3, 4, 5, 6 CM288R-25B WHITE

33(J) 2, 3, 4 CM288-33A WHITE 29(H) 2, 3, 4, 5, 6 CM288R-29B WHITE

33(J) 1, 5, 6 CM288-33B WHITE 33(J) 2, 3, 4, 5, 6 CM288R-33B WHITE

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-288 18 11 THRU 33 CM-S-288R 18 11 THRU 33

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 11
MIL-DTL-38999
SERIES I
MANUFACTURER: SERIES:
AMERICAN MICRO 3
AMPHENOL/SOCAPEX 416, MB91, LJT, 5388`, ILJT
AMPHENOL/PYLE NATIONAL G, P, T1
DEUTSCH/TE CTC, DJT
ELECTRONIC SEALS  SERIES I
GLASSEAL 700
GLENAIR 90000, 9220, 230, 231, 232, 91500, 92200
ITT CANNON/VEAM KJJL, KJL, LTT
PLESSEY  CT, LCT
SAE HM (SERIES I)
SEALTRON 9700
SOURIAU 8LT
Wall Mount Receptacle Shown SPACECRAFT COMPONENTS DCR, DCP
CORSAIR HI REL 7600
RMS R07

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: BAYONET
SHELL FINISH
KEYING POSITIONS: BLANK (NORMAL),
ALUMINUM  Bright Cadmium Over Nickel
A, B, C, D Cadmium Olive Drab Over Nickel
ALTERNATE KEYING ROTATION OF MASTER Anodize
METHOD: KEY – MINOR KEYS Nickel
REMAIN STATIONARY STAINLESS STEEL Passivated
EMI/RFI GROUNDING: YES (EMI/RFI GROUNDING Nickel
FINGERS MAY NOT STEEL Fused Tin
BE AVAILABLE ON
ALL ­MODELS)

TYPICAL CONNECTOR
PART NUMBER
MS 27467 E 13 F 8 P A
BREAKDOWN MILITARY PREFIX KEYING POSITION
SHELL STYLE CONTACT TYPE (PIN OR SOCKET)
CLASS INSERT ARRANGEMENT
SHELL SIZE FINISH

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR
BASIC IDENT. #/DESCRIPTION
SIZE POSITIONS NUMBER COLOR

MS27467/Straight, EMI grounding 9 ALL CM389L-9 BLUE MS27466/Wall mount 9 ALL CM389LR-9 BLUE
MS27498/90º 11 ALL CM389L-11 BLUE MS27468/Jam nut 11 ALL CM389LR-11 BLUE
MS27653/Straight, EMI grounding MS27469/Hermetic wall mount
MS27661/Straight plug, lanyard 13 ALL CM389L-13 BLUE MS27470/Hermetic jam nut 13 ALL CM389LR-13 BLUE
release MS27471/Hermetic solder mount
15 ALL CM389L-15 BLUE 15 ALL CM389LR-15 BLUE
MS27496/Box mount
17 ALL CM389L-17 BLUE MS27505/Box mount, 17 ALL CM389LR-17 BLUE
(rear panel mounting)
19 ALL CM389L-19 BLUE 19 ALL CM389LR-19 BLUE
MS27515/Wall mount,
21 ALL CM389L-21 BLUE (rear panel mounting) 21 ALL CM389LR-21 BLUE
MS27652/Wall mount
23 ALL CM389L-23 BLUE MS27654/Wall mount, 23 ALL CM389LR-23 BLUE
(rear panel mounting)
25 ALL CM389L-25 BLUE 25 ALL CM389LR-25 BLUE
MS27656/Wall mount,
(rear panel mounting)
MS27662/Thru-bulkhead

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-389L 9 9 THRU 25 CM-S-389LR 9 9 THRU 25

PAGE 12 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MIL-DTL-38999
SERIES II
MANUFACTURER: SERIES:
AMERICAN MICRO 4
AERO ELECTRIC AE273
AMPHENOL 418, JT, MB91
CONNECTOR INDUSTRIES G, H
CORSAIR CJ
DETORONICS DJT
ELECTRONIC SEALS SERIES II
GLASSEAL 800
GLENAIR 231, 232, 233
HERMETIC SEAL CORP. 900000
ITT CANNON KJ, KJM
PLESSEY CT
Straight Plug Shown SPI MS
SEALTRON 9800, A9B03
SOURIAU 8LT, 8TO, 8T2
HI REL 53000, 54010

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: BAYONET
SHELL FINISH
KEYING POSITIONS: BLANK (NORMAL),
ALUMINUM  Nickel
A, B, C, D Bright Cadmium Over Nickel
ALTERNATE KEYING MASTER KEY ROTATES – Cadmium Olive Drab Over Nickel
METHOD: MINOR KEYS REMAIN Anodize
STATIONARY STAINLESS STEEL Passivated
EMI/RFI GROUNDING: YES (EMI/RFI GROUNDING Nickel
FINGERS MAY NOT STEEL Fused Tin
BE AVAILABLE ON
ALL ­MODELS)

TYPICAL CONNECTOR
PART NUMBER
MS 27473 E 12 F 8 P A
BREAKDOWN MILITARY PREFIX KEYING POSITION
SHELL STYLE CONTACT TYPE (PIN OR SOCKET)
CLASS INSERT ARRANGEMENT
SHELL SIZE FINISH

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR

MS27473/Straight 8 ALL CM389S-8 GRAY MS27472/Wall mount 8 ALL CM264R-8 ORANGE

MS27480/Straight 10 ALL CM389S-10 GRAY MS27474/Jam nut 10 ALL CM264R-10 ORANGE
MS27484/Straight, EMI grounding MS27475/Hermetic wall mount
MS27500/90º 12 ALL CM389S-12 GRAY MS27476/Hermetic box nut 12 ALL CM264R-12 ORANGE

14 ALL CM389S-14 GRAY MS27477/Hermetic jam mount 14 ALL CM264R-14 ORANGE

MS27478/Hermetic solder mount
16 ALL CM389S-16 GRAY MS27479/Wall mount 16 ALL CM264R-16 ORANGE

18 ALL CM389S-18 GRAY MS27481/Jam mount 18 ALL CM264R-18 ORANGE

MS27482/Hermetic wall mount
20 ALL CM389S-20 GRAY MS27483/Hermetic jam nut 20 ALL CM264R-20 ORANGE

22 ALL CM389S-22 GRAY MS27497/Wall mount, 22 ALL CM264R-22 ORANGE

back panel mounting
24 ALL CM389S-24 GRAY MS27499/Box mount 24 ALL CM264R-24 ORANGE
MS27503/Hermetic solder mount
MS27504/Box mount
MS27508/Box mount, back panel
mounting
MS27513/Box mount, long grommet
MS27664/Wall mount, back panel
mounting

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-389S 9 8 THRU 24 CM-S-264R 9 8 THRU 24

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 13
MIL-DTL-38999
SERIES III
CORSAIR CJ
G&H TECH/COOPER G300/G3GB, G3L6
AMPHENOL/PYLE NATIONAL T3
AMPHENOL TV, 5565, T3, MT93, TVP, CTVP, ITV, TVS
AMPHENOL/SOCAPEX TVP, TVO7
AERO ELECTRIC 38999, AE320, AE322
DEUTSCH/TE DTS, ACT
ELECTRONIC SEALS SERIES III
ITT CANNON KJA, KJB, VTTP
PLESSEY TCT
AB CONNECTORSABAC
HI REL 85010, 86000, 59000, 87000
SEALTRON 9900, 9903
HERMETIC SEAL HR
CONESYS EUROPE AE
Wall Mount Receptacle Shown AMERICAN MICRO 5, 2, 6
SPACECRAFT SC999
SOURAIU 8D5, 200

COUPLING METHOD: THREADED, TRIPLE SHELL MATERIAL & FINISH:

START SELF-LOCKING
SHELL FINISH
KEYING POSITIONS: N (NORMAL), A, B, C, D, E
ALUMINUM  Anodize
ALTERNATE KEYING MASTER KEY REMAINS Nickel
METHOD:  STATIONARY – Cadmium Olive Drab
MINOR KEYS ROTATE STEEL Passivated
­INDEPENDENTLY Nickel
EMI/RFI GROUNDING: YES (EMI /RFI GROUNDING
­FINGERS MAY NOT BE
­AVAILABLE ON ALL MODELS)

TYPICAL CONNECTOR
PART NUMBER
D38999/26
F J 30 P N
BREAKDOWN MILITARY SPECIFICATION SHEET KEYING POSITION
CLASS CONTACT TYPE (PIN OR SOCKET)
SHELL SIZE INSERT ARRANGEMENT

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION BASIC IDENT. #/DESCRIPTION
SIZE POSITIONS NUMBER COLOR SIZE POSITIONS NUMBER COLOR

D38999/26/Straight 9(A) N, C, D CM389T-9A LAVENDER D38999/20/ Wall mount 9(A) N CM389TR-9A LAVENDER
D38999/29/ L
 anyard release 9(A) A, B, E CM389T-9B LAVENDER D38999/21/ Hermetic seal box 11(B) N CM389TR-11A LAVENDER
D38999/30/ L
 anyard release mount
D38999/31/ L
 anyard release 11(B) N, D, E CM389T-11A LAVENDER D38999/23/ H ermetic seal jam nut 13(C) N CM389TR-13A LAVENDER
D38999/36/ L
 anyard release (25(J) D38999/24/ Jam nut
11(B) A, B, C CM389T-11B LAVENDER 15(D) N CM389TR-15A LAVENDER
Cell size only) D38999/25/ Hermetic seal solder
13(C) N, D, E CM389T-13A LAVENDER mount 17(E) N CM389TR-17A LAVENDER
D38999/27/ H ermetic seal weld
13(C) A, B, C CM389T-13B LAVENDER mount 19(F) N CM389TR-19A LAVENDER
D38999/34/ B reakaway, jam nut (25
15(D) N, D, E CM389T-15A LAVENDER (J) shell size only) 21(G) N CM389TR-21A LAVENDER

15(D) A, B, C CM389T-15B LAVENDER D38999/35/Breakaway, wall mount 23(H) N CM389TR-23A LAVENDER

(25 (J) shell size only)
17(E) N, A, B CM389T-17A LAVENDER 25(J) N CM389TR-25A LAVENDER

17(E) C, D, E CM389T-17B LAVENDER 9(A) A, B, C, D, E CM389TR-9B LAVENDER

19(F) N, A, B CM389T-19A LAVENDER 11(B) A, B, C, D, E CM389TR-11B LAVENDER

19(F) C, D, E CM389T-19B LAVENDER 13(C) A, B, C, D, E CM389TR-13B LAVENDER

21(G) N, A, B CM389T-21A LAVENDER 15(D) A, B, C, D, E CM389TR-15B LAVENDER

21(G) C, D, E CM389T-21B LAVENDER 17(E) A, B, C, D, E CM389TR-17B LAVENDER

23(H) N, A, B CM389T-23A LAVENDER 19(F) A, B, C, D, E CM389TR-19B LAVENDER

23(H) C, D, E CM389T-23B LAVENDER 21(G) A, B, C, D, E CM389TR-21B LAVENDER

25(J) N, A, B CM389T-25A LAVENDER 23(H) A, B, C, D, E CM389TR-23B LAVENDER

25(J) C, D, E CM389T-25B LAVENDER 25(J) A, B, C, D, E CM389TR-25B LAVENDER

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-389T 18 9 THRU 25 CM-S-389TR 18 9 THRU 25

PAGE 14 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MIL-DTL-38999
SERIES IV
MANUFACTURER: SERIES:
DEUTSCH/TE DIV
ELECTRONIC SEALS SERIES IV
G & H TECH/COOPER BL
AMPHENOL ML94
CINCH CN
GLENAIR 230

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: BREECH-LOCK
SHELL FINISH
(SELF LOCKING)
Wall Mount Receptacle Shown KEYING POSITIONS: N (NORMAL), A, B, C, D
ALUMINUM 
Anodize
Nickel
ALTERNATE KEYING MASTER KEY REMAINS Cadmium Olive Drab
METHOD:  STATIONARY – STEEL Passivated
INTERLOCKING Nickel
SECTIONS ROTATE
­INDEPENDENTLY
EMI/RFI GROUNDING: YES (EMI /RFI GROUNDING
­FINGERS MAY NOT BE
­AVAILABLE ON ALL MOD-
ELS)

TYPICAL CONNECTOR
PART NUMBER
D38999/46
F J 35 P N
BREAKDOWN MILITARY SPECIFICATION SHEET KEYING POSITION
CLASS CONTACT TYPE (PIN OR SOCKET)
SHELL SIZE INSERT ARRANGEMENT

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION BASIC IDENT. #/DESCRIPTION
SIZE POSITIONS NUMBER COLOR SIZE POSITIONS NUMBER COLOR

D38999/46/EMI straight 11(B) ALL CM389B-11 BEIGE D38999/40/ Wall mount 11(B) ALL CM389BR-11 BEIGE
D38999/47/ S
 traight 13(C) ALL CM389B-13 BEIGE D38999/41/ H
 ermetic box mount 13(C) ALL CM389BR-13 BEIGE
D38999/42 / B ox mount
15(D) ALL CM389B-15 BEIGE D38999/43 / Hermetic jam nut 15(D) ALL CM389BR-15 BEIGE

17(E) ALL CM389B-17 BEIGE D38999/44 / Jam nut 17(E) ALL CM389BR-17 BEIGE
D38999/45 / H ermetic solder mount
19(F) ALL CM389B-19 BEIGE D38999/48/ H ermetic weld mount 19(F) ALL CM389BR-19 BEIGE

21(G) ALL CM389B-21 BEIGE D38999/49/ In-line 21(G) ALL CM389BR-21 BEIGE

23(H) ALL CM389B-23 BEIGE 23(H) ALL CM389BR-23 BEIGE

25(J) ALL CM389B-25 BEIGE 25(J) ALL CM389BR-25 BEIGE

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-389B 8 11 THRU 25 CM-S-389BR 8 11 THRU 25

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 15
MIL-C-81511
SERIES I & III
MANUFACTURER: SERIES:
AMPHENOL 348
DEUTSCH/TE 815
HERMETIC SEAL CORP. 10-00000

COUPLING METHOD: BAYONET SHELL MATERIAL & FINISH:

KEYING POSITIONS: 1, 2, 3, 4, 5, 6 SHELL FINISH
ALTERNATE KEYING MASTER KEY REMAINS
ALUMINUM  Nickel
STATIONARY – Cadmium Olive Drab Over Nickel
MINOR KEYS ROTATE Cadmium Olive Drab
­INDEPENDENTLY STAINLESS STEEL Passivated
EMI/RFI GROUNDING: YES – PLUGS CONTAIN STEEL Tin
EMI/RFI GROUNDING
Straight Plug Shown ­FINGERS

TYPICAL CONNECTOR
PART NUMBER
M81511/26
E D 01 P 1
BREAKDOWN MILITARY SPECIFICATION SHEET KEYING POSITION
CLASS CONTACT TYPE (PIN OR SOCKET)
SHELL SIZE INSERT ARRANGEMENT

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR

M81511/26/Straight 8(A) 1, 2, 3 CM815L-8A YELLOW M81511/21/Wall mount 8(A) ALL CM815R-8 YELLOW
M81511/46/Straight 8(A) 4, 5, 6 CM815L-8B YELLOW M81511/23/Jam nut 10(B) ALL CM815R-10 YELLOW
M81511/25/In-line
10(B) 1, 2, 6 CM815L-10A YELLOW M81511/41/Wall mount 14(D) ALL CM815R-14 YELLOW

10(B) 3, 4, 5 CM815L-10B YELLOW M81511/45/In-line 16(E) ALL CM815R-16 YELLOW

M81511/49/Jam nut
14(D) 1, 2, 6 CM815L-14A YELLOW 18(F) ALL CM815R-18 YELLOW

14(D) 3, 4, 5 CM815L-14B YELLOW 20(G) ALL CM815R-20 YELLOW

16(E) 1, 2, 3 CM815L-16A YELLOW 22(H) ALL CM815R-22 YELLOW

16(E) 4, 5, 6 CM815L-16B YELLOW 24(J) ALL CM815R-24 YELLOW

18(F) 1, 2, 3 CM815L-18A YELLOW

18(F) 4, 5, 6 CM815L-18B YELLOW

20(G) 1, 2, 3 CM815L-20A YELLOW

20(G) 4, 5, 6 CM815L-20B YELLOW

22(H) 1, 2, 3 CM815L-22A YELLOW

22(H) 4, 5, 6 CM815L-22B YELLOW

24(J) 1, 2, 3 CM815L-24A YELLOW

24(J) 4, 5, 6 CM815L-24B YELLOW

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-815L 16 8 THRU 24 CM-S-815R 8 8 THRU 24

PAGE 16 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MIL-C-81511
SERIES II & IV
MANUFACTURER: SERIES:
AMPHENOL 348
DEUTSCH/TE 815

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: BAYONET
SHELL FINISH
KEYING POSITIONS: 1, 2, 3, 4, 5, 6
ALUMINUM  Nickel
ALTERNATE KEYING MASTER KEY REMAINS Cadmium Olive Drab Over Nickel
METHOD: STATIONARY – Cadmium Olive Drab
MINOR KEYS ROTATE STAINLESS STEEL Passivated
­INDEPENDENTLY STEEL Tin
EMI/RFI GROUNDING: YES
Straight Plug Shown

TYPICAL CONNECTOR
PART NUMBER
M81511/06
E D 01 P 1
BREAKDOWN MILITARY SPECIFICATION SHEET KEYING POSITION
CLASS CONTACT TYPE (PIN OR SOCKET)
SHELL SIZE INSERT ARRANGEMENT

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR

M81511/06/Straight 8(A) ALL CM815S-8 RED M81511/01/Wall mount 8(A) ALL CM815R-8 YELLOW
M81511/56/Straight 10(B) 1, 4, 5 CM815S-10A RED M81511/03/Jam nut 10(B) ALL CM815R-10 YELLOW
M81511/05/In-line
10(B) 2, 3, 6 CM815S-10B RED M81511/51/Wall mount 14(D) ALL CM815R-14 YELLOW

14(D) 1, 4, 5 CM815S-14A RED M81511/53/Jam nut 16(E) ALL CM815R-16 YELLOW

M81511/53/Jam nut
14(D) 2, 3, 6 CM815S-14B RED 18(F) ALL CM815R-18 YELLOW

16(E) 1, 2, 4 CM815S-16A RED 20(G) ALL CM815R-20 YELLOW

16(E) 3, 5, 6 CM815S-16B RED 22(H) ALL CM815R-22 YELLOW

18(F) 1, 2, 4 CM815S-18A RED 24(J) ALL CM815R-24 YELLOW

18(F) 3, 5, 6 CM815S-18B RED

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-815S 9 8 THRU 18 CM-S-815R 8 8 THRU 24

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 17
MIL-DTL-83723 SERIES I
(REPLACED BY MIL-DTL-26482, SERIES 2)

MANUFACTURER: SERIES:
AERO ELECTRIC AE77/AE8337
AMPHENOL 118, DC, FPT(21-), PT, PT*CE, SP*CE, PT*SE, PTS*DR, SP, MB1
BURNDY BT, L*T
CONNECTOR INDUSTRIES C, K
DETORONICS DT
DEUTSCH/TE/TE AFD, DBC, RBC, 450, 460, 810, 880
ELECTRONIC SEALS 9-
GENERAL CONNECTOR GC, GC*C
GLASSEAL BE, GB
HERMETIC SEAL CORP. S*A-7000, 7000
ITT CANNON KPD, KPSE, KSSE, KP*, KS*, KPT, KSP, KPTM, KSPM, PV,
PVA, PVJ, PVW, PVX
SEALTRON 6300, 8100, 8300
Straight Plug Shown S.E.C. PW
SOURIAU 851, 851*R, 8526
VEAM/LITTON VPT, VPT*SE, VUT

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: BAYONET
SHELL FINISH
KEYING POSITIONS: N (NORMAL), W, X, Y, Z
ALUMINUM Anodize
ALTERNATE KEYING ROTATION OF INSERT – Nickel
METHOD: KEYS REMAIN STATIONARY STAINLESS STEEL Passivated
EMI/RFI GROUNDING: YES (EMI/RFI GROUNDING
STEEL Tin
FINGERS MAY NOT
BE AVAILABLE ON ALL
­MODELS)

TYPICAL CONNECTOR
PART NUMBER
M83723/13
A 22 55 N
BREAKDOWN MILITARY SPECIFICATION SHEET KEYING POSITION
CLASS INSERT ARRANGEMENT
SHELL SIZE

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR
SIZE POSITIONS NUMBER COLOR
M83723/13/Straight 8 ALL CM264-8 ORANGE M83723/01/ Narrow flange wall 8 ALL CM264R-8 ORANGE
M83723/14/Straight mount
10 ALL CM264-10 ORANGE 10 ALL CM264R-10 ORANGE
M82723/36/Prewired size 8 straight M83723/02/ Narrow flange wall
mount 12 ALL CM264R-12 ORANGE
M83723/37/ Prewired size 8 straight 12 ALL CM264-12 ORANGE
M83723/03/ Wide flange wall mount
M83723/42/Straight, RFI grounding 14 ALL CM264R-14 ORANGE
14 ALL CM264-14 ORANGE M83723/04/ Wide flange wall mount
M83723/43/Straight, RFI grounding
M83723/05/ Jam nut 16 ALL CM264R-16 ORANGE
M83723/43/Straight, RFI grounding 16 ALL CM264-16 ORANGE
M83723/06/ Jam nut
M83723/48/Prewired size 8 straight, 18 ALL CM264R-18 ORANGE
RFI grounding 18 ALL CM264-18 ORANGE M83723/07/ In-line
M83723/49/Prewired size 8 straight, M83723/08/ In-line 20 ALL CM264R-20 ORANGE
20 ALL CM264-20 ORANGE
RFI grounding M83723/09/ Hermetic narrow flange
22 ALL CM264-22 ORANGE box mount 22 ALL CM264R-22 ORANGE
M83723/10/ Hermetic wide flange
box mount 24 ALL CM264R-24 ORANGE
M83723/11/ Hermetic solder mount
M83723/12/ Hermetic jam nut
M83723/38/ Prewired size 8 narrow
flange wall mount
M83723/39/ Prewired size 8 narrow
flange wall mount
M83723/40/ Prewired size 8 wide
flange wall mount
M83723/41/ Prewired size 8 wide
flange wall mount

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-264 9 8 THRU 24 CM-S-264R 9 8 THRU 24

PAGE 18 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MIL-DTL-83723 SERIES II
(INTERMATEABLE WITH AS50151)

MANUFACTURER: SERIES:
AERO ELECTRIC AE55, AE723
AMPHENOL 69, 72, 97, 157, 172, 173, 179, 208, 238, 246, BT-M, BT-RA, HT,
SCP, TBF, 10-72, 10-214, 10-244, 10-741, 10-747, 10-873,
10-874, 5015, MFR, M723, 944, 981
ITT CANNON BFH, BFR, CA, CA-EA, CA-EB, CA-HR, CA-KE, CA-RX, CV,
CVA, EX-A, FRA, FRF, FVA, FVF, FW, GS, MR, TBF, TBFH, WFS

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: THREADED
SHELL FINISH
KEYING POSITIONS: N (NORMAL), W, X, Y, Z
Wall Mount Receptacle Shown ALTERNATE KEYING ROTATION OF INSERT –
ALUMINUM Anodize
Nickel
METHOD: KEYS REMAIN STATIONARY
STEEL Tin
EMI/RFI GROUNDING: NO
STAINLESS STEEL Passivated

TYPICAL CONNECTOR
PART NUMBER
M83723/23
G 22 55 N
BREAKDOWN MILITARY SPECIFICATION SHEET KEYING POSITION
CLASS INSERT ARRANGEMENT
SHELL SIZE

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR

M83723/23/Straight 8 ALL CM5015-8 CHROME M83723/17/In-line 8 ALL CM5015R-8 CHROME

M83723/24/Straight 10 ALL CM5015-10 CHROME M83723/18/In-line 10 ALL CM5015R-10 CHROME
M83723/52/Straight, self-locking M83723/19/Wall mount
coupling nut 12 ALL CM5015-12 CHROME M83723/20/Wall mount 12 ALL CM5015R-12 CHROME
M83723/53/Straight, self-locking M83723/21/Box mount
coupling nut 14 ALL CM5015-14 CHROME 14 ALL CM5015R-14 CHROME
M83723/22/Box mount
16 ALL CM5015-16 CHROME M83723/25/Box mount hermetic 16 ALL CM5015R-16 CHROME

18 ALL CM5015-18 CHROME M83723/26/Solder mount hermetic 18 ALL CM5015R-18 CHROME

20 ALL CM5015-20 CHROME 20 ALL CM5015R-20 CHROME

22 ALL CM5015-22 CHROME 22 ALL CM5015R-22 CHROME

24 ALL CM5015-24 CHROME 24 ALL CM5015R-24 CHROME

28 ALL CM5015-28 CHROME 28 ALL CM5015R-28 CHROME

32 ALL CM5015-32 CHROME 32 ALL CM5015R-32 CHROME

36 ALL CM5015-36 CHROME 36 ALL CM5015R-36 CHROME

40 ALL CM5015-40 CHROME 40 ALL CM5015R-40 CHROME

44 ALL CM5015-44 CHROME 44 ALL CM5015R-44 CHROME

48 ALL CM5015-48 CHROME 48 ALL CM5015R-48 CHROME

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-5015 15 8 THRU 48 CM-S-5015R 15 8 THRU 48

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 19
MIL-DTL-83723 SERIES III
(REF: MIL-C-26500)
MANUFACTURER: SERIES:
AMPHENOL 48, 518, MB3, MT3, B, BFH
BOEING (SPECIFICATION) BACC45F
DEUTSCH/TE DB, DL, 94603
HERMETIC SEAL CORP. 83723
ITT CANNON HTMF
SEALTRON 6500, 6600
GLENAIR G534
J-TECH JT837
AERO ELECTRIC AE83
AMPHENOL/MATRIX MB, MQ
RMS RO73
AMPHENOL/PYLE NATIONAL BY, BJK, BT, BEN
AMERICAN MICRO 30J, 20, 40,50K
HI REL 690000, 70000, 71000

Wall Mount Receptacle Shown

COUPLING METHOD: BAYONET OR THREADED SHELL MATERIAL & FINISH:
KEYING POSITIONS: N (NORMAL), 1, 2, 3, 4, 5,
SHELL FINISH
6, 7, 8, 9, 10
ALTERNATE KEYING INSERT ROTATION IN ALUMINUM Black Anodize
Cadmium
METHOD: POSITIONS 1 THRU 5,
MINOR KEY ROTATION STAINLESS STEEL Passivated
Nickel
IN POSITIONS 6 THRU 10
EMI/RFI GROUNDING: YES (EMI/RFI FINGERS STEEL Tin
MAY NOT BE AVAILABLE
ON ALL MODELS)

TYPICAL CONNECTOR
PART NUMBER
M83723/75
F 22 55 N
BREAKDOWN MILITARY SPECIFICATION SHEET KEYING POSITION
CLASS INSERT ARRANGEMENT
SHELL SIZE

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
SIZE POSITIONS NUMBER COLOR BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR

M83723/66/ Straight, push-pull quick 8 N, 8, 9 CM837-8A* GREEN M83723/65/ Jam nut, hermetic seal 8 ALL CM837RB-8 GREEN
disconnect M83723/71/ Wall mount
M83723/67/ Straight, push-pull quick 8 6, 7 CM837-8B* GREEN 10 ALL CM837RB-10 GREEN
M83723/72/ Wall mount
disconnect M83723/73/ Jam nut
8 N, 8, 9 CM837-8C** GREEN 12 ALL CM837RB-12 GREEN
M83723/68/ Straight, push-pull quick M83723/74/ Jam nut
disconnect, ­lanyard 8 6, 7 CM837-8D** GREEN 14 ALL CM837RB-14 GREEN
M83723/79/ Box mount,
M83723/69/ Straight, push-pull quick hermetic seal
disconnect, ­lanyard 10 N, 8, 9 CM837-10A GREEN 16 ALL CM837RB-16 GREEN
M83723/80/ Solder mount,
M83723/75/Straight hermetic seal
10 6, 7, 10 CM837-10B GREEN 18 ALL CM837RB-18 GREEN
M83723/76/ Straight M83723/81/ Jam nut,
M83723/77/ Straight, EMI grounding 12 N, 6, 8 CM837-12A GREEN hermetic seal 20 ALL CM837RB-20 GREEN
M83723/78/ Straight, EMI grounding M83723/93/ Solder mount,
12 7, 9, 10 CM837-12B GREEN 22 ALL CM837RB-22 GREEN
M83723/87/ Straight hermetic seal
M83723/91/ Straight, EMI grounding 14 N, 6, 8 CM837-14A GREEN M83723/94/ Jam nut, hermetic seal 24 ALL CM837RB-24 GREEN
M83723/92/ Straight, EMI grounding
14 7, 9, 10 CM837-14B GREEN
M83723/96/ Straight, self-locking
coupling nut 16 N, 6, 8 CM837-16A GREEN
M83723/97/ Straight, self-locking
coupling nut, EMI 16 7, 9, 10 CM837-16B GREEN
grounding
M83723/98/ Straight, self-locking 18 N, 6, 8 CM837-18A GREEN
coupling nut, EMI
grounding 18 7, 9, 10 CN837-18B GREEN

20 N, 6, 8 CM837-20A GREEN

20 7, 9, 10 CM837-20B GREEN

22 N, 6, 8 CM837-22A GREEN

22 7, 9, 10 CM837-22B GREEN

24 N, 6, 8 CM837-24A GREEN

24 7, 9, 10 CM837-24B GREEN

28 N, 6, 8 CM837-28A GREEN

28 7, 9, 10 CM837-28B GREEN
*For bayonet coupling only. **For threaded coupling connectors only. Bayonet couplings only. Adaptors not available for connectors with threaded coupling.

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-837 22 8 THRU 28 CM-S-837RB* 9 8 THRU 24

PAGE 20 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
PATTERN 602
PAN 6432-4, EL2112
MANUFACTURER: SERIES:
AMPHENOL 602GB
CANNON ELECTRIC GB PVX
HELLERMANN DEUTSCH/TE RR
SOURIAU 8526

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: BAYONET SHELL FINISH
KEYING POSITIONS: N (NORMAL), B, C, E,
ALUMINUM Cadmium Olive Drab
F FOR SHELL;
N (NORMAL), W, X, Y, Z
FOR INSERT
ALTERNATE KEYING MASTER KEY REMAINS
Straight Plug Shown METHOD:  STATIONARY – MINOR
KEYS AND BAYONET PINS
ROTATE. ALSO, INSERT
ROTATES
EMI/RFI GROUNDING: YES (EMI/RFI GROUNDING
­FINGERS MAY NOT BE
­AVAILABLE ON ALL MODELS)

TYPICAL CONNECTOR
PART NUMBER
602 6 - 18 - 32 P N
BREAKDOWN IDENTIFICATION NUMBER KEYING POSITION
SHELL STYLE CONTACT TYPE (PIN OR SOCKET)
SHELL SIZE NUMBER OF CONTACTS

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION BASIC IDENT. #/DESCRIPTION
SIZE POSITIONS NUMBER COLOR SIZE POSITIONS NUMBER COLOR

6026/Plug 8 N CM602-8A PURPLE 6020/ Square flange 8 ALL CM264R-8 ORANGE

8 E, F CM602-8B PURPLE 6027/ Jam nut 10 ALL CM264R-10 ORANGE

6021H/ Solder fixing hermetic
10 N, B, C CM602-10A PURPLE 6027H/ Jam nut hermetic 12 ALL CM264R-12 ORANGE

10 E, F CM602-10B PURPLE 14 ALL CM264R-14 ORANGE

12 N, B, C CM602-12A PURPLE 16 ALL CM264R-16 ORANGE

12 E, F CM602-12B PURPLE 18 ALL CM264R-18 ORANGE

14 N, B, C CM602-14A PURPLE 20 ALL CM264R-20 ORANGE

14 E, F CM602-14B PURPLE 22 ALL CM264R-22 ORANGE

16 N, B, C CM602-16A PURPLE 24 ALL CM264R-24 ORANGE

16 E, F CM602-16B PURPLE

18 N, B, C CM602-18A PURPLE

18 E, F CM602-18B PURPLE

20 N, B, C CM602-20A PURPLE

20 E, F CM602-20B PURPLE

22 N, B, C CM602-22A PURPLE

22 E, F CM602-22B PURPLE

24 N, B, C CM602-24A PURPLE

24 E, F CM602-24B PURPLE

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-602 18 8 THRU 24 CM-S-264R 9 8 THRU 24

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 21
PATTERN 615
PAN 6433-2
MANUFACTURER: SERIES:
AMPHENOL SJT
PLESSEY MK26

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: BAYONET
SHELL FINISH
KEYING POSITIONS: BLANK (NORMAL),
ALUMINUM  Cadmium Over Nickel
A, B, C, D Bright Cadmium
ALTERNATE KEYING MASTER KEY ROTATES – Cadmium Olive Drab
METHOD: MINOR KEYS REMAIN Gray Anodize
­STATIONARY Anodic Coating (Alumilite)
EMI/RFI GROUNDING: YES (EMI/RFI GROUNDING Bright Nickel
Chromate Treated (Iridite 14-2)
FINGERS MAY NOT Cadmium Olive Drab Over Nickel
Wall Mount Receptacle Shown BE AVAILABLE ON ALL Nickel
­MODELS) STEEL Tin
STAINLESS STEEL Passivated

TYPICAL CONNECTOR
PART NUMBER
SJT 00 RT - 18 - 66 P A 005
BREAKDOWN I.D. NO. FINISH
SHELL STYLE KEYING POSITION
SERVICE CLASS CONTACT TYPE (PIN OR SOCKET)
SHELL SIZE INSERT ARRANGEMENT

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
SHELL KEYING ADAPTOR TOOL SHELL KEYING ADAPTOR TOOL
BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR BASIC IDENT. #/DESCRIPTION SIZE POSITIONS NUMBER COLOR

SJT06RT/Straight 8 ALL CMSJT-8 GOLD SJT00RT/Wall mount 8 ALL CM264R-8 ORANGE

SJTG06RT/Straight, RFI grounding 10 ALL CMSJT-10 GOLD SJTP02RE/Box mount 10 ALL CM264R-10 ORANGE
fingers SJTP00RT/Wall mount
12 ALL CMSJT-12 GOLD SJT07RT/Jam nut 12 ALL CM264R-12 ORANGE

14 ALL CMSJT-14 GOLD SJTIY/Solder mount hermetic 14 ALL CM264R-14 ORANGE

SJT07Y/Jam nut hermetic
16 ALL CMSJT-16 GOLD 16 ALL CM264R-16 ORANGE

18 ALL CMSJT-18 GOLD 18 ALL CM264R-18 ORANGE

20 ALL CMSJT-20 GOLD 20 ALL CM264R-20 ORANGE

22 ALL CMSJT-22 GOLD 22 ALL CM264R-22 ORANGE

24 ALL CMSJT-24 GOLD 24 ALL CM264R-24 ORANGE

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-SJT 9 8 THRU 24 CM-S-264R 9 8 THRU 24

PAGE 22 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MICRO CONNECTORS
2M801/801
MANUFACTURER: SERIES:
AMPHENOL 2M
GLENAIR Mighty Mouse

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: DUAL-START ACME
SHELL FINISH
THREAD
ALUMINUM Black Anodize
KEYING POSITIONS: A, B, C, D, E, F
Electroless Nickel
ALTERNATE KEYING 
METHOD:  Cadmium w/ Olive Drab Chromate
EMI/RFI GROUNDING:  Zinc-Nickel w/ Black Chromate
Nickel-PTFE

Wall Mount Receptacle Shown STAINLESS STEEL Passivated

TYPICAL CONNECTOR
PART NUMBER
801 - 007 - 16 M - 9-4 P A
BREAKDOWN SERIES POLARIZATION
SHELL STYLE CONTACT TYPE (PIN OR SOCKET)
SHELL MATERIAL AND FINISH
SHELL SIZE - INSERT ARRANGEMENT

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL
SIZE POSITIONS NUMBER SIZE POSITIONS NUMBER
2M801-007/ Plug with Integral Backshell 2M801-009/ Receptacle with Integral Backshell
5 A, B, E CM801-05A* 5 A, B, F CM801R-05A
2M801-008/ Plug with Accessory Threads 2M801-010/ Receptacle with Accessory
5 C, D CM801-05B* 5 D, E CM801R-05B
Threads
5 A CM801-05AA* 5 A CM801R-05AA
801-007/ Plug With Banding Platform 5 B CM801-05BB* 801-009/ Receptacle With Banding 5 B CM801R-05BB
Platform
801-008/ Plug With Rear Accessory Thread 5 C CM801-05CC* 5 C CM801R-05CC
801-010/ Receptacle With Accessory Thread
5 D CM801-05DD* 5 D CM801R-05DD
5 E CM801-05EE* 5 E CM801R-05EE
5 F CM801-05FF* 5 F CM801R-05FF
6 A, B, E CM801-06A* 6 A, B, F CM801R-06A
6 C, D CM801-06B* 6 D, E CM801R-06B
6 A CM801-06AA* 6 A CM801R-06AA
6 B CM801-06BB* 6 B CM801R-06BB
6 C CM801-06CC* 6 C CM801R-06CC
6 D CM801-06DD* 6 D CM801R-06DD
6 E CM801-06EE* 6 E CM801R-06EE
6 F CM801-06FF* 6 F CM801R-06FF
7 A, B, E CM801-07A* 7 A, B, F CM801R-07A
7 C, D CM801-07B* 7 D, E CM801R-07B
7 A CM801-07AA* 7 A CM801R-07AA
7 B CM801-07BB* 7 B CM801R-07BB
7 C CM801-07CC* 7 C CM801R-07CC
7 D CM801-07DD* 7 D CM801R-07DD
7 E CM801-07EE 7 E CM801R-07EE
7 F CM801-07FF* 7 F CM801R-07FF

These tools are made to fit Amphenol Connectors

*Indicates that tools also fit Glenair Connectors

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-801 18 5-21 CM-S-801R 30 5-21

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 23
 MICRO CONNECTORS
2M801/801 (CONTINUED)
ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL
SIZE POSITIONS NUMBER SIZE POSITIONS NUMBER
2M801-007/ Plug with Integral Backshell 2M801-009/ Receptacle with Integral Backshell
8 A, B, E CM801-08A* 8 A, B, F CM801R-08A
2M801-008/ Plug with Accessory Threads 2M801-010/ Receptacle with Accessory
8 C, D CM801-08B* 8 D, E CM801R-08B
Threads
8 A CM801-08AA* 8 A CM801R-08AA
801-007/ Plug With Banding Platform 801-009/ Receptacle With Banding
8 B CM801-08BB* 8 B CM801R-08BB
Platform
801-008/ Plug With Rear Accessory Thread 8 C CM801-08CC* 8 C CM801R-08CC
801-010/ Receptacle With Accessory Thread
8 D CM801-08DD* 8 D CM801R-08DD
8 E CM801-08EE* 8 E CM801R-08EE
8 F CM801-08FF* 8 F CM801R-08FF
9 A-F CM801-09A 9 A, B, F CM801R-09A
9 A CM801-09AA 9 D, E CM801R-09B
9 B CM801-09BB 9 A CM801R-09AA
9 C CM801-09CC 9 B CM801R-09BB
9 D CM801-09DD 9 C CM801R-09CC
9 E CM801-09EE 9 D CM801R-09DD
9 F CM801-09FF 9 E CM801R-09EE
10 A-F CM801-10A 9 F CM801R-09FF
10 A CM801-10AA 10 A, B, F CM801R-10A
10 B CM801-10BB 10 D, E CM801R-10B
10 C CM801-10CC 10 A CM801R-10AA
10 D CM801-10DD 10 B CM801R-10BB
10 E CM801-10EE 10 C CM801R-10CC
10 F CM801-10FF 10 D CM801R-10DD
13 A-F CM801-13A* 10 E CM801R-10EE
13 A CM801-13AA* 10 F CM801R-10FF
13 B CM801-13BB* 13 A, B, F CM801R-13A
13 C CM801-13CC* 13 D, E CM801R-13B
13 D CM801-13DD* 13 A CM801R-13AA
13 E CM801-13EE* 13 B CM801R-13BB
13 F CM801-13FF* 13 C CM801R-13CC
16 A-F CM801-16A 13 D CM801R-13DD
16 A CM801-16AA 13 E CM801R-13EE
16 B CM801-16BB 13 F CM801R-13FF
16 C CM801-16CC 16 A, B, F CM801R-16A
16 D CM801-16DD 16 D, E CM801R-16B
16 E CM801-16EE 16 A CM801R-16AA
16 F CM801-16FF 16 B CM801R-16BB
17 A-F CM801-17A 16 C CM801R-16CC
17 A CM801-17AA 16 D CM801R-16DD
17 B CM801-17BB 16 E CM801R-16EE
17 C CM801-17CC 16 F CM801R-16FF
17 D CM801-17DD 17 A, B, F CM801R-17A
17 E CM801-17EE 17 D, E CM801R-17B
17 F CM801-17FF 17 A CM801R-17AA
17 B CM801R-17BB
17 C CM801R-17CC

These tools are made to fit Amphenol Connectors 17 D CM801R-17DD

*Indicates that tools also fit Glenair Connectors 17 E CM801R-17EE

17 F CM801R-17FF

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-801 18 5-21 CM-S-801R 30 5-21

PAGE 24 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MICRO CONNECTORS
2M801/801 (CONTINUED)
ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL
SIZE POSITIONS NUMBER SIZE POSITIONS NUMBER
2M801-007/ Plug with Integral Backshell 2M801-009/ Receptacle with Integral Backshell
21 A-F CM801-21A 21 A, B, F CM801R-21A
2M801-008/ Plug with Accessory Threads 2M801-010/ Receptacle with Accessory
21 A CM801-21AA 21 D, E CM801R-21B
Threads
21 B CM801-21BB 21 A CM801R-21AA
801-007/ Plug With Banding Platform 801-009/ Receptacle With Banding
21 C CM801-21CC 21 B CM801R-21BB
Platform
801-008/ Plug With Rear Accessory Thread 21 D CM801-21DD 21 C CM801R-21CC
801-010/ Receptacle With Accessory Thread
21 E CM801-21EE 21 D CM801R-21DD
21 F CM801-21FF 21 E CM801R-21EE
11 A CM801-11A 21 F CM801R-21FF
11 B CM801-11B 11 A CM801R-11A
11 C CM801-11C 11 B CM801R-11B
11 D CM801-11D 11 C CM801R-11C
19 A CM801-19A 11 D CM801R-11D
19 B CM801-19B 19 A CM801R-19A
19 C CM801-19C 19 B CM801R-19B
19 D CM801-19D 19 C CM801R-19C
19 D CM801R-19D

These tools are made to fit Amphenol Connectors

*Indicates that tools also fit Glenair Connectors

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-801 18 5-21 CM-S-801R 30 5-21

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 25
 MICRO CONNECTORS
2M803/803
MANUFACTURER: SERIES:
AMPHENOL 2M
GLENAIR Mighty Mouse

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: BAYONET
SHELL FINISH
KEYING POSITIONS: A, B, C, D, E, F
ALUMINUM Black Anodize
ALTERNATE KEYING 
Electroless Nickel
METHOD: 
EMI/RFI GROUNDING:  Cadmium w/ Olive Drab Chromate
Zinc-Nickel w/ Black Chromate
Nickel-PTFE

Wall Mount Receptacle Shown STAINLESS STEEL Passivated

TYPICAL CONNECTOR
PART NUMBER
803 - 007 - 16 M - 9-4 P A
BREAKDOWN SERIES POLARIZATION
SHELL STYLE CONTACT TYPE (PIN OR SOCKET)
SHELL MATERIAL AND FINISH
SHELL SIZE - INSERT ARRANGEMENT

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)

BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL
SIZE POSITIONS NUMBER SIZE POSITIONS NUMBER
803-001/ Plug with Integral Backshell 803-003/ Receptacle with Banding Platform
5 N, X CM803-05A 5 N, X CM803R-05A
803-002/ Plug with Accessory Threads 5 Y, Z CM803-05B 803-004/ Receptacle with Accessory Threads 5 N CM803R-05NN
5 N CM803-05NN 5 X CM803R-05XX
5 X CM803-05XX 5 Y CM803R-05YY
5 Y CM803-05YY 5 Z CM803R-05ZZ
5 Z CM803-05ZZ 6 N, X CM803R-06A
6 N, X CM803-06A 6 N CM803R-06NN
6 Y, Z CM803-06B 6 X CM803R-06XX
6 N CM803-06NN 6 Y CM803R-06YY
6 X CM803-06XX 6 Z CM803R-06ZZ
6 Y CM803-06YY 7 N, X CM803R-07A
6 Z CM803-06ZZ 7 N CM803R-07NN
7 N, X CM803-07A 7 X CM803R-07XX
7 Y, Z CM803-07B 7 Y CM803R-07YY
7 N CM803-07NN 7 Z CM803R-07ZZ
7 X CM803-07XX 8 N, X CM803R-08A
7 Y CM803-07YY 8 N CM803R-08NN
7 Z CM803-07ZZ 8 X CM803R-08XX
8 N, X CM803-08A 8 Y CM803R-08YY
8 Y, Z CM803-08B 9 N, X CM803R-09A
8 N CM803-08NN 9 N CM803R-09NN
8 X CM803-08XX 9 X CM803R-09XX
8 Y CM803-08YY 9 Y CM803R-09YY
8 Z CM803-08ZZ 9 Z CM803R-09ZZ

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-803 18 5-15 CM-S-803R 27 5-15

PAGE 26 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MICRO CONNECTORS
2M803/803 (CONTINUED)
ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL
SIZE POSITIONS NUMBER SIZE POSITIONS NUMBER
803-001/ Plug with Integral Backshell 803-003/ Receptacle with Banding Platform
9 N, X CM803-09A 10 N, X CM803R-10A
803-002/ Plug with Accessory Threads 9 Y, Z CM803-09B 803-004/ Receptacle with Accessory Threads 10 N CM803R-10NN
9 N CM803-09NN 10 X CM803R-10XX
9 X CM803-09XX 10 Y CM803R-10YY
9 Y CM803-09YY 10 Z CM803R-10ZZ
9 Z CM803-09ZZ 12 N, X CM803R-12A
10 N, X CM803-10A 12 N CM803R-12NN
10 Y, Z CM803-10B 12 X CM803R-12XX
10 N CM803-10NN 12 Y CM803R-12YY
10 X CM803-10XX 12 Z CM803R-12ZZ
10 Y CM803-10YY 14 N, X CM803R-14A
10 Z CM803-10ZZ 14 N CM803R-14NN

12 N, X CM803-12A 14 X CM803R-14XX

12 Y, Z CM803-12B 14 Y CM803R-14YY

12 N CM803-12NN 14 Z CM803R-14ZZ

12 X CM803-12XX 15 N, X CM803R-15A

12 Y CM803-12YY 15 N CM803R-15NN

12 Z CM803-12ZZ 15 X CM803R-15XX

14 N, X CM803-14A 15 Y CM803R-15YY

14 Y, Z CM803-14B 15 Z CM803R-15ZZ

14 N CM803-14NN
14 X CM803-14XX
14 Y CM803-14YY
14 Z CM803-14ZZ
15 N, X CM803-15A
15 Y, Z CM803-15B
15 N CM803-15NN
15 X CM803-15XX
15 Y CM803-15YY
15 Z CM803-15ZZ

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-803 18 5-15 CM-S-803R 27 5-15

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 27
 MICRO CONNECTORS
2M804/804
MANUFACTURER: SERIES:
AMPHENOL 2M
GLENAIR Mighty Mouse

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: PUSH-PULL
SHELL FINISH
KEYING POSITIONS: A, B, C, D, E, F
ALUMINUM Black Anodize
ALTERNATE KEYING 
Electroless Nickel
METHOD: 
EMI/RFI GROUNDING:  Cadmium w/ Olive Drab Chromate
Zinc-Nickel w/ Black Chromate
Nickel-PTFE

STAINLESS STEEL Passivated

TYPICAL CONNECTOR
PART NUMBER
804 - 007 - 16 M - 9-4 P A
BREAKDOWN SERIES POLARIZATION
SHELL STYLE CONTACT TYPE (PIN OR SOCKET)
SHELL MATERIAL AND FINISH
SHELL SIZE - INSERT ARRANGEMENT

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL
SIZE POSITIONS NUMBER SIZE POSITIONS NUMBER
804-001/ Plug with Banding Platform 804-003 Receptacle with Banding Platform
5 A, B, E, U CM804-05A 5 A, B, F CM804R-05A
805-002/ Plug with Accessory Threads 804-004/ Receptacle with Accessory Threads
5 C, D, U CM804-05B 5 D, E CM804R-05B
5 A, U CM804-05AA 5 A CM804R-05AA
5 B, U CM804-05BB 5 B CM804R-05BB
5 C, U CM804-05CC 5 C CM804R-05CC
5 D, U CM804-05DD 5 D CM804R-05DD
5 E, U CM804-05EE 5 E CM804R-05EE
5 F, U CM804-05FF 5 F CM804R-05FF
5 U - SINGLE MASTER CM804-05 5 U CM804R-05UU
6 A, B, E, U CM804-06A 6 A, B, F CM804R-06A
6 C, D, U CM804-06B 6 D, E CM804R-06B
6 A, U CM804-06AA 6 A CM804R-06AA
6 B, U CM804-06BB 6 B CM804R-06BB
6 C, U CM804-06CC 6 C CM804R-06CC
6 D, U CM804-06DD 6 D CM804R-06DD
6 E, U CM804-06EE 6 E CM804R-06EE
6 F, U CM804-06FF 6 F CM804R-06FF
6 U - SINGLE MASTER CM804-06 6 U CM804R-06UU
7 A, B, E, U CM804-07A 7 A, B, F CM804R-07A
7 C, D, U CM804-07B 7 D, E CM804R-07B
7 A, U CM804-07AA 7 A CM804R-07AA
7 B, U CM804-07BB 7 B CM804R-07BB
7 C, U CM804-07CC 7 C CM804R-07CC
7 D, U CM804-07DD 7 D CM804R-07DD
7 E, U CM804-07EE 7 E CM804R-07EE
7 F, U CM804-07FF 7 F CM804R-07FF
7 U - SINGLE MASTER CM804-07 7 U CM804R-07UU

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-804 13 5-15 CM-S-804R 18 5-15

PAGE 28 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MICRO CONNECTORS
2M804/804 (CONTINUED)
ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL
SIZE POSITIONS NUMBER SIZE POSITIONS NUMBER
804-001/ Plug with Banding Platform 804-003 Receptacle with Banding Platform
8 A, B, E, U CM804-08A 8 A, B, F CM804R-08A
805-002/ Plug with Accessory Threads 804-004/ Receptacle with Accessory Threads
8 C, D, U CM804-08B 8 D, E CM804R-08B
8 A, U CM804-08AA 8 A CM804R-08AA
8 B, U CM804-08BB 8 B CM804R-08BB
8 C, U CM804-08CC 8 C CM804R-08CC
8 D, U CM804-08DD 8 D CM804R-08DD
8 E, U CM804-08EE 8 E CM804R-08EE
8 F, U CM804-08FF 8 F CM804R-08FF
8 U - SINGLE MASTER CM804-08 8 U CM804R-08UU
9 A, B, C, E, F, U CM804-09A 9 A, B, F CM804R-09A
9 A, U CM804-09AA 9 D, E CM804R-09B
9 B, U CM804-09BB 9 A CM804R-9AA

9 C, U CM804-09CC 9 B CM804R-9BB

9 D, U CM804-09DD 9 C CM804R-9CC

9 E, U CM804-09EE 9 D CM804R-9DD

9 F, U CM804-09FF 9 E CM804R-9EE

9 U - SINGLE MASTER CM804-09 9 F CM804R-9FF

10 A, B, C, E, F, U CM804-10A 9 U CM804R-9UU

10 A, U CM804-10AA 10 A, B, F CM804R-10A

10 B, U CM804-10BB 10 D, E CM804R-10B

10 C, U CM804-10CC 10 A CM804R-10AA

10 D, U CM804-10DD 10 B CM804R-10BB

10 E, U CM804-10EE 10 C CM804R-10CC

10 F, U CM804-10FF 10 D CM804R-10DD

10 U - SINGLE MASTER CM804-10 10 E CM804R-10EE

12 A, B, C, E, F, U CM804-12A 10 F CM804R-10FF

12 A, U CM804-12AA 10 U CM804R-10UU

12 B, U CM804-12BB 12 A, B, F CM804R-12A

12 C, U CM804-12CC 12 D, E CM804R-12B

12 D, U CM804-12DD 12 A CM804R-12AA

12 E, U CM804-12EE 12 B CM804R-12BB

12 F, U CM804-12FF 12 C CM804R-12CC

12 U - SINGLE MASTER CM804-12 12 D CM804R-12DD

14 A, B, C, E, F, U CM804-14A 12 E CM804R-12EE

14 A, U CM804-14AA 12 F CM804R-12FF

14 B, U CM804-14BB 12 U CM804R-12UU

14 C, U CM804-14CC 14 A, B, F CM804R-14A

14 D, U CM804-14DD 14 D, E CM804R-14B

14 E, U CM804-14EE 14 A CM804R-14AA

14 F, U CM804-14FF 14 B CM804R-14BB

14 U - SINGLE MASTER CM804-14 14 C CM804R-14CC

14 D CM804R-14DD
14 E CM804R-14EE
14 F CM804R-14FF
14 U CM804R-14UU

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-804 13 5-15 CM-S-804R 18 5-15

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 29
 MICRO CONNECTORS
2M804/804 (CONTINUED)
ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL
SIZE POSITIONS NUMBER SIZE POSITIONS NUMBER
804-001/ Plug with Banding Platform 804-003 Receptacle with Banding Platform
15 A, B, C, E, F, U CM804-15A 804-004/ Receptacle with Accessory Threads 15 A, B, F CM804R-15A
805-002/ Plug with Accessory Threads
15 A, U CM804-15AA 15 D, E CM804R-15B
15 B, U CM804-15BB 15 A CM804R-15AA
15 C, U CM804-15CC 15 B CM804R-15BB
15 D, U CM804-15DD 15 C CM804R-15CC
15 E, U CM804-15EE 15 D CM804R-15DD
15 F, U CM804-15FF 15 E CM804R-15EE
15 U - SINGLE MASTER CM804-15 15 F CM804R-15FF
15 U CM804R-15UU

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-804 13 5-15 CM-S-804R 18 5-15

PAGE 30 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
MICRO CONNECTORS
2M805/805
MANUFACTURER: SERIES:
AMPHENOL 2M
GLENAIR Mighty Mouse

SPECIFICATIONS: SHELL MATERIAL & FINISH:

COUPLING METHOD: TRI-START
SHELL FINISH
KEYING POSITIONS: A, B, C, D, E, F
ALUMINUM Black Anodize
ALTERNATE KEYING 
Electroless Nickel
METHOD: 
EMI/RFI GROUNDING:  Cadmium w/ Olive Drab Chromate
Zinc-Nickel w/ Black Chromate
Nickel-PTFE

STAINLESS STEEL Passivated

TYPICAL CONNECTOR 805 - 020 - 16 M - 9-4 P A

PART NUMBER
BREAKDOWN SERIES POLARIZATION
SHELL STYLE CONTACT TYPE (PIN OR SOCKET)
SHELL MATERIAL AND FINISH
SHELL SIZE - INSERT ARRANGEMENT

ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL
SIZE POSITIONS NUMNBER SIZE POSITIONS NUMNBER
2M805-001/ Plug with Integral Backshell 2M805-003/ Receptacle with Integral Backshell
8 A, B, E CM805-08A* 8 A, B, F CM805R-08A
2M805-002/ Plug with Accessory Threads 8 C, D CM805-08B* 2M805-004/ Receptacle with Accessory 8 D, E CM805R-08B
Threads
8 A CM805-08AA* 8 A CM805R-08AA
8 B CM805-08BB* 8 B CM805R-08BB
8 C CM805-08CC* 8 C CM805R-08CC
8 D CM805-08DD* 8 D CM805R-08DD
8 E CM805-08EE* 8 E CM805R-08EE
8 F CM805-08FF* 8 F CM805R-08FF
9 A, B, E CM805-09A* 9 A, B, F CM805R-09A
9 C, D CM805-09B* 9 D, E CM805R-09B
9 A CM805-09AA* 9 A CM805R-09AA
9 B CM805-09BB* 9 B CM805R-09BB
9 C CM805-09CC* 9 C CM805R-09CC
9 D CM805-09DD* 9 D CM805R-09DD
9 E CM805-09EE* 9 E CM805R-09EE
9 F CM805-09FF* 9 F CM805R-09FF
10 A, B, C, E, F CM805-10A 10 A, B, F CM805R-10A
10 A CM805-10AA 10 D, E CM805R-10B
10 B CM805-10BB 10 A CM805R-10AA
10 C CM805-10CC 10 B CM805R-10BB
10 D CM805-10DD 10 C CM805R-10CC
10 E CM805-10EE 10 D CM805R-10DD
10 F CM805-10FF 10 E CM805R-10EE
10 F CM805R-10FF

These tools are made to fit Amphenol Connectors

*Indicates that tools also fit Glenair Connectors

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-805 16 8-23 CM-S-805R 27 8-23

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 31
 MICRO CONNECTORS
2M805/805 (CONTINUED)
ADAPTOR TOOLS
PLUG (REMOVABLE PORTION) RECEPTACLE (STATIONARY PORTION)
BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL BASIC IDENT. #/DESCRIPTION SHELL KEYING ADAPTOR TOOL
SIZE POSITIONS NUMNBER SIZE POSITIONS NUMNBER
2M805-001/ Plug with Integral Backshell 2M805-003/ Receptacle with Integral Backshell
11 A, B, C, E, F CM805-11A* 11 A, B, F CM805R-11A
2M805-002/ Plug with Accessory Threads 2M805-004/ Receptacle with Accessory
11 A CM805-11AA* Threads 11 D, E CM805R-11B
11 B CM805-11BB* 11 A CM805R-11AA
11 C CM805-11CC* 11 B CM805R-11BB
11 D CM805-11DD* 11 C CM805R-11CC
11 E CM805-11EE* 11 D CM805R-11DD
11 F CM805-11FF* 11 E CM805R-11EE
12 A, B, C, E, F CM805-12A* 11 F CM805R-11FF
12 A CM805-12AA* 12 A, B, F CM805R-12A
12 B CM805-12BB* 12 D, E CM805R-12B
12 C CM805-12CC* 12 A CM805R-12AA
12 D CM805-12DD* 12 B CM805R-12BB
12 E CM805-12EE* 12 C CM805R-12CC
12 F CM805-12FF* 12 D CM805R-12DD
15 A, B, C, E, F CM805-15A* 12 E CM805R-12EE
15 A CM805-15AA* 12 F CM805R-12FF
15 B CM805-15BB* 15 A, B, F CM805R-15A
15 C CM805-15CC* 15 D, E CM805R-15B
15 D CM805-15DD* 15 A CM805R-15AA
15 E CM805-15EE* 15 B CM805R-15BB
15 F CM805-15FF* 15 C CM805R-15CC
18 A, B, C, D, E, F CM805-18A* 15 D CM805R-15DD
18 A CM805-18AA* 15 E CM805R-15EE
18 B CM805-18BB* 15 F CM805R-15FF
18 C CM805-18CC* 18 A, B, F CM805R-18A
18 D CM805-18DD* 18 D, E CM805R-18B
18 E CM805-18EE* 18 A CM805R-18AA
23 A, B, C, D, E, F CM805-23A* 18 B CM805R-18BB
23 A CM805-23AA* 18 C CM805R-18CC
23 B CM805-23BB* 18 D CM805R-18DD
23 C CM805-23CC* 18 E CM805R-18EE
23 D CM805-23DD* 18 F CM805R-18FF
23 E CM805-23EE* 19 A, B, F CM805R-19A
23 F CM805-23FF* 23 A, B, F CM805R-23A
23 C CM805-23CC 23 D, E CM805R-23B
23 D CM805-23DD 23 A CM805R-23AA
23 E CM805-23EE 23 B CM805R-23BB
23 F CM805-23FF 23 C CM805R-23CC
23 D CM805R-23DD
23 E CM805R-23EE
23 F CM805R-23FF

These tools are made to fit Amphenol Connectors

*Indicates that tools also fit Glenair Connectors

ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE) ADAPTOR SET PART NO. ADAPTORS IN SET COVERAGE (SHELL SIZE)

CM-S-805 16 8-23 CM-S-805R 27 8-23

PAGE 32 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 CONNECTOR
IDENTIFICATION

THIS TABLE CAN BE USED TO IDENTIFY THE ADAPTOR TOOL SERIES REQUIRED FOR A PARTICULAR
­CONNECTOR. IF YOU KNOW THE COMMERCIAL OR MILITARY PREFIX OF THE CONNECTOR PART NUMBER,
FIND IT IN THE LEFT COLUMN. IN THE SECOND COLUMN WILL BE THE APPLICABLE PAGE NUMBER FOR THE ­
ADAPTOR TOOL SERIES, ALONG WITH MANUFACTURER AND SPECIFICATION REFERENCE INFORMATION.

CONNECTOR SERIES CONNECTOR SERIES CONNECTOR SERIES

PREFIX PAGE MANUFACTURER PREFIX PAGE MANUFACTURER PREFIX PAGE MANUFACTURER
(REFERENCE) (REFERENCE) (REFERENCE)
HERMETIC MIL-C-81511 CONNECTOR MIL-C-26500 HERMETIC MIL-DTL-83723 SERIES I
10-00000 16 26500 10 7000 18
SEAL CORP. SERIES 1 & 3 INDUSTRIES SEAL CORP.
HERMETIC MIL-C-81511
10-00000 17 26500 10 ELECTRONIC MIL-DTL-26500 72 6 AMPHENOL AS505151
SEAL CORP. SERIES 2 & 4
MIL-C-22992 HERMETIC MIL-DTL-26500 72 19 AMPHENOL MIL-C-83723 SERIES II
10-194 7 AMPHENOL 26500 10
CLASSES C, J, R SEAL CORP.
75 6 VEAM/LITTON AS505151
10-214 6 AMPHENOL AS505151 348 16 AMPHENOL MIL-C-81511 SERIES 1 & 3
10-214 19 AMPHENOL MIL-C-83723 SERIES II 75 19 VEAM/LITTON MIL-C-83723 SERIES II
348 17 AMPHENOL MIL-C-81511 SERIES 2 & 4 800 13 GLASSEAL MIL-C-38999 SERIES II
10-244 6 AMPHENOL AS505151
10-244 19 AMPHENOL MIL-C-83723 SERIES II 416 12 AMPHENOL MIL-DTL-38999 SERIES I 801 23 GLENAIR
10-473 8 AMPHENOL MIL-C-22992 CLASS L 418 13 AMPHENOL MIL-DTL-38999 SERIES II 803 26 GLENAIR
10-72 6 AMPHENOL AS505151 450 9 DEUTSCH/TE MIL-DTL-26482 SERIES 1 & 2 804 28 GLENAIR
10-72 19 AMPHENOL MIL-C-83723 SERIES II 805 31 GLENAIR
450 18 DEUTSCH/TE MIL-DTL-83723 SERIES I
10-741 6 AMPHENOL AS505151 8000 6 SEALTRON AS505151
10-741 19 AMPHENOL MIL-C-83723 SERIES II 460 9 DEUTSCH/TE MIL-DTL-26482 SERIES 1 & 2
8000 19 SEALTRON MIL-DTL-83723 SERIES II
10-747 6 AMPHENOL AS505151 460 18 DEUTSCH/TE MIL-DTL-83723 SERIES I
810 9 DEUTSCH/TE MIL-DTL-26482 SERIES 1 & 2
10-747 19 AMPHENOL MIL-C-83723 SERIES II 48 10 AMPHENOL MIL-DTL-26500
810 18 DEUTSCH/TE MIL-DTL-83723 SERIES I
10-873 6 AMPHENOL AS505151 48 20 AMPHENOL MIL-DTL-83723 SERIES III
8100 9 SEALTRON MIL-DTL-26482 SERIES 1 & 2
10-873 19 AMPHENOL MIL-C-83723 SERIES II 48-7005 10 AMPHENOL MIL-DTL-26500
8100 18 SEALTRON MIL-DTL-83723 SERIES I
10-874 6 AMPHENOL AS505151 50 10 GLASSEAL MIL-DTL-26500
815 16 DEUTSCH/TE MIL-DTL-81511 SERIES 1 & 3
10-874 19 AMPHENOL MIL-C-83723 SERIES II 50 20 GLASSEAL MIL-DTL-83723 SERIES III
10/71 6 VEAM/LITTON AS505151 5015 6 AMPHENOL AS505151 815 17 DEUTSCH/TE MIL-DTL-81511 SERIES 2 & 4

10/71 19 VEAM/LITTON MIL-C-83723 SERIES II ELECTRONIC AS505151 8300 9 SEALTRON MIL-DTL-26482 SERIES 1 & 2
5015 6
SEALS 8300 18 SEALTRON MIL-DTL-83723 SERIES I
MIL-C-26482
118 9 AMPHENOL
SERIES 1 & 2 5015 19 AMPHENOL MIL-DTL-83723 SERIES II HERMETIC MIL-DTL-83723 SERIES III
83723 20
118 18 AMPHENOL MIL-C-83723 SERIES I ELECTRONIC MIL-DTL-83723 SERIES II SEAL CORP.
5015 19
SEALS
157 6 AMPHENOL AS505151 83723 20 SOURIAU MIL-DTL-83723 SERIES IIII
518 10 AMPHENOL MIL-DTL-26500
157 19 AMPHENOL MIL-C-83723 SERIES II CONNECTOR MIL-DTL-83723 SERIES III
83723 III 20
518 20 AMPHENOL MIL-DTL-83723 SERIES III INDUSTRIES
172 6 AMPHENOL AS505151
5388 12 AMPHENOL MIL-DTL-38999 SERIES I 8500 10 SEALTRON MIL-DTL-26500
172 19 AMPHENOL MIL-C-83723 SERIES II
5565 14 AMPHENOL MIL-DTL-38999 SERIES III 851 9 SOURIIAU MIL-DTL-26482 SERIES 1 & 2
173 6 AMPHENOL AS505151
6000 6 SEALTRON AS505151 851 18 SOURIAU MIL-DTL-83723 SERIES I
173 19 AMPHENOL MIL-C-83723 SERIES II
6000 19 SEALTRON MIL-DTL-83723 SERIES II 851*R 9 SOURIAU MIL-DTL-26482 SERIES 1 & 2
179 6 AMPHENOL AS505151
602GB 21 AMPHENOL PATTERN 602 851*R 18 SOURIAU MIL-DTL-83723 SERIES I
179 19 AMPHENOL MIL-C-83723 SERIES II
2M801 23 AMPHENOL 6300 9 SEALTRON MIL-DTL-26482 SERIES 1 & 2 8526 9 SOURIAU MIL-DTL-26482 SERIES 1 & 2

2M805 31 AMPHENOL 8526 18 SOURIAU MIL-DTL-83723 SERIES I

6300 18 SEALTRON MIL-DTL-83723 SERIES I
HERMETIC AS505151 8526 21 SOURIAU PATTERN 602
2000 6 6500 10 SEALTRON MIL-DTL-26500
SEAL CORP.
8530 10 SOURIAU MIL-DTL-26500
6500 20 SEALTRON MIL-DTL-83723 SERIES III
HERMETIC MIL-C-83723 8530 20 SOURIAU MIL-DTL-83723 SERIES III
2000 19 6600 10 SEALTRON MIL-C-26500
SEAL CORP. SERIES II
6600 20 SEALTRON MIL-C-83723 SERIES III 8600 10 SEALTRON MIL-DTL-26500
208 6 AMPHENOL AS505151
208 19 AMPHENOL MIL-C-83723 SERIES II 69 6 AMPHENOL AS505151 88-194 7 AMPHENOL MIL-DTL-22992 CLASSES C, J, R
229 8 AMPHENOL MIL-C-22992 CLASS L 69 19 AMPHENOL MIL-DTL-83723 SERIES II
880 9 DEUTSCH/TE MIL-DTL-26482 SERIES 1 & 2
238 6 AMPHENOL AS505151 700 12 GLASSEAL MIL-DTL-38999 SERIES I
880 18 DEUTSCH/TE MIL-DTL-83723 SERIES I
238 19 AMPHENOL MIL-C-83723 SERIES II HERMETIC
7000 9 MIL-DTL-26482 SERIES 1 & 2
SEAL CORP. 8LT 12 SOURIAU MIL-DTL-38999 SERIES I
246 6 AMPHENOL AS505151
IT 13 SOURIAU MIL-DTL-38999 SERIES II
246 19 AMPHENOL MIL-C-83723 SERIES II

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 33
CONNECTOR
IDENTIFICATION
CONNECTOR SERIES CONNECTOR SERIES CONNECTOR SERIES
PREFIX PAGE MANUFACTURER PREFIX PAGE MANUFACTURER PREFIX PAGE MANUFACTURER
(REFERENCE) (REFERENCE) (REFERENCE)

9— 9
ELECTRONIC
MIL-DTL-26482 SERIES 1 & 2
BT 9 BURNDY MIL-C-26482 SERIES 1 & 2 D38999/45 14 MILITARY MIL-DTL-38999 SERIES III
SEALS
BT 18 BURNDY MIL-C-83723 SERIES I D38999/46 14 MILITARY MIL-DTL-38999 SERIES III
ELECTRONIC
9— 18
SEALS
MIL-DTL-83723 SERIES I BT-M 6 AMPHENOL AS505151 D38999/47 14 MILITARY MIL-DTL-38999 SERIES III
HERMETIC
BT-M 19 AMPHENOL MIL-C-83723 SERIES II D38999/48 14 MILITARY MIL-DTL-38999 SERIES III
900000 12 MIL-DTL-38999 SERIES I
SEAL CORP. BT-RA 6 AMPHENOL AS505151 D38999/49 14 MILITARY MIL-DTL-38999 SERIES III
HERMETIC BT-RA 19 AMPHENOL MIL-C-83723 SERIES II DB 10 DEUTSCH/TE MIL-DTL-26500
900000 13 MIL-DTL-38999 SERIES II
SEAL CORP.
DB 20 DEUTSCH/TE MIL-DTL-83723 SERIES III
MATRIX C 9 CONNECTOR MIL-C-26482 SERIES 1 & 2
944 6 AS505151 INDUSTRIES
SCIENCE DBC 9 DEUTSCH/TE MIL-DTL-26482 SERIES 1 & 2
944 19 AMPHENOL MIL-C-83723 SERIES II C 18 CONNECTOR MIL-C-83723 SERIES I
INDUSTRIES DBC 18 DEUTSCH/TE MIL-DTL-83723 SERIES I
94603 10 DEUTSCH/TE MIL-C-26500 C48 10 CINCH MIL-C-26500 DC 9 AMPHENOL MIL-DTL-26482 SERIES 1 & 2
94603 20 DEUTSCH/TE MIL-C-83723 SERIES III CA 6 AS505151 AS505151 DC 18 AMPHENOL MIL-DTL-83723 SERIES I
97 6 AMPHENOL AS505151 CA 19 ITT CANNON MIL-C-83723 SERIES II DIV 15 DEUTSCH/TE MIL-DTL-38999 SERIES IV
97 19 AMPHENOL MIL-C-83723 SERIES II CA-EA 6 ITT CANNON AS505151 DJT 12 DEUTSCH/TE MIL-DTL-38999 SERIES I
9700 12 SEALTRON MIL-C-38999 SERIES I CA-EA 19 ITT CANNON AS505151 DJT 13 DETORONICS MIL-DTL-38999 SERIES II
9800 13 SEALTRON MIL-C-38999 SERIES II CA-EB 6 ITT CANNON AS505151 DL 10 DEUTSCH/TE MIL-DTL-26500
MATRIX CA-EB 19 ITT CANNON MIL-C-83723 SERIES II DL 20 DEUTSCH/TE MIL-DTL-83723 SERIES III
981 6 SCIENCE AS505151
CA-HR 6 ITT CANNON AS505151 DS 6 DETORONICS AS505151
981 19 AMPHENOL MIL-C-83723 SERIES II CA-HR 19 ITT CANNON MIL-C-83723 SERIES II DS 19 DETORONICS MIL-DTL-83723 SERIES II
CA-KE 6 ITT CANNON AS505151 DT 9 DETORONICS MIL-DTL-26482
9900 14 SEALTRON MIL-C-38999 SERIES III SERIES 1 & 2
CA-KE 19 ITT CANNON MIL-C-83723 SERIES II
A 6 CONNECTOR AS505151 DT 18 DETORONICS MIL-DTL-83723 SERIES I
INDUSTRIES CA-RX 6 ITT CANNON AS505151
DTS 14 DEUTSCH/TE MIL-DTL-38999 SERIES III
CONNECTOR CA-RX 19 ITT CANNON MIL-DTL-83723 SERIES II
A 19 INDUSTRIES MIL-C-83723 SERIES II DX 10 DETORONICS MIL-C-26500
CN 15 CINCH MIL-DTL-38999 SERIES IV
AERO DX 20 DETORONICS MIL-C-83723 SERIES III
AE55 6 AS505151 CN0915 10 CINCH MIL-DTL-26500
ELECTRIC EX-A 6 ITT CANNON AS505151
CN0930 10 CINCH MIL-DTL-26500
AE55 19 AERO MIL-C-83723 SERIES II EX-A 19 ITT CANNON MIL-C-83723 SERIES II
ELECTRIC CN0930 20 CINCH MIL-DTL-83723 SERIES III
F 10 PYLE- MIL-C-26500
AERO CN0942 10 CINCH MIL-DTL-26500 NATIONAL
AE723 6 ELECTRIC AS505151
CN0966 10 CINCH MIL-DTL-26500 FLIGHT
AERO FC 6 CONNECTOR AS505151
AE723 19 MIL-DTL-83723 SERIES II CN0966 20 CINCH MIL-DTL-83723 SERIES III
ELECTRIC
CN0967 10 CINCH MIL-DTL-26500 FC 19 FLIGHT MIL-C-83723 SERIES II
AE77 9 AERO MIL-DTL-26482 SERIES 1 & 2 CONNECTOR
ELECTRIC CN0967 20 CINCH MIL-DTL-83723 SERIES III
FF0 6 FLIGHT AS505151
AERO CT 12 PLESSEY MIL-DTL-38999 SERIES I CONNECTOR
AE77 18 ELECTRIC MIL-DTL-83723 SERIES I
CT 13 PLESSEY MIL-DTL-38999 SERIES II FLIGHT
AFD 9 DEUTSCH/TE MIL-DTL-26482 SERIES 1 & 2 FF0 19 CONNECTOR MIL-C-83723 SERIES II
CTC 12 DEUTSCH/TE MIL-C-38999 SERIES I
AFD 18 DEUTSCH/TE MIL-DTL-83723 SERIES I CV 6 ITT CANNON AS505151 FF5 6 FLIGHT AS505151
CONNECTOR
B 10 PYLE- MIL-DTL-26500 CV 19 ITT CANNON MIL-C-83723 SERIES II
NATIONAL FLIGHT MIL-C-83723 SERIES II
CVA 6 ITT CANNON AS505151 FF5 19 CONNECTOR
B 20 PYLE- MIL-DTL-83723 SERIES III
NATIONAL CVA 19 ITT CANNON MIL-DTL-83723 SERIES II FLIGHT
FH 6 CONNECTOR AS505151
B555 8 MIL-DTL-22992 CLASS L CWLD 7 ITT CANNON  MIL-DTL-22992 CLASSES
C, J, R FLIGHT
B556 8 BURNDY MIL-DTL-22992 CLASS L FH 19 CONNECTOR MIL-C-83723 SERIES II
D38999/20 14 MILITARY MIL-DTL-38999 SERIES III
B557 8 BURNDY MIL-DTL-22992 CLASS L FPT(21-) 9 AMPHENOL MIL-C-26482 SERIES 1 & 2
D38999/21 14 MILITARY MIL-DTL-38999 SERIES III
B558 8 BURNDY MIL-DTL-22992 CLASS L FPT(21-) 18 AMPHENOL MIL-C-83723 SERIES I
D38999/23 14 MILITARY MIL-DTL-38999 SERIES III
BACC45F 10 BOEING MIL-DTL-26500 FRA 6 ITT CANNON AS505151
D38999/24 14 MILITARY MIL-DTL-38999 SERIES III
BACC45F 20 BOEING MIL-DTL-83723 SERIES III FRA 19 ITT CANNON MIL-C-83723 SERIES II
D38999/25 14 MILITARY MIL-DTL-38999 SERIES III
BACC63 10 BOEING MIL-DTL-26500 FRF 6 ITT CANNON AS505151
D38999/26 14 MILITARY MIL-DTL-38999 SERIES III
BE 9 GLASSEAL MIL-DTL-26482 SERIES 1 & 2 FRF 19 ITT CANNON MIL-C-83723 SERIES II
D38999/27 14 MILITARY MIL-DTL-38999 SERIES III
BE 18 GLASSEAL MIL-DTL-83723 SERIES I FVA 6 ITT CANNON AS505151
D38999/29 14 MILITARY MIL-DTL-38999 SERIES III
BFH 6 ITT CANNON AS505151 FVA 19 ITT CANNON MIL-C-83723 SERIES II
D38999/30 14 MILITARY MIL-DTL-38999 SERIES III
BFH 10 AMPHENOL MIL-C-26500 FVF 6 ITT CANNON AS505151
D38999/31 14 MILITARY MIL-DTL-38999 SERIES III
BFH 19 ITT CANNON AS505151 D38999/40 14 MILITARY MIL-DTL-38999 SERIES III FVF 19 ITT CANNON MIL-C-83723 SERIES II
BFH 20 AMPHENOL MIL-C-83723 SERIES III D38999/41 14 MILITARY MIL-DTL-38999 SERIES III FW 6 ITT CANNON AS505151
BFR 6 ITT CANNON AS505151 D38999/42 14 MILITARY MIL-DTL-38999 SERIES III FW 19 ITT CANNON MIL-C-83723 SERIES II
BFR 19 ITT CANNON MIL-C-83723 SERIES II D38999/43 14 MILITARY MIL-DTL-38999 SERIES III FLIGHT
FZC 6 CONNECTOR AS505151
BL 15  G&H MIL-C-38999 SERIES IV D38999/44 14 MILITARY MIL-DTL-38999 SERIES III
TECHNOLOGY FLIGHT
FZC 19 CONNECTOR MIL-C-83723 SERIES II

PAGE 34 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 CONNECTOR SERIES CONNECTOR SERIES CONNECTOR SERIES
PREFIX PAGE MANUFACTURER PREFIX PAGE MANUFACTURER PREFIX PAGE MANUFACTURER
(REFERENCE) (REFERENCE) (REFERENCE)
FLIGHT KPTM 9 ITT CANNON MIL-DTL-26482 SERIES 1 & 2 M81511/35 16 MILITARY MIL-DTL--81511 SERIES 1 & 3
FZH 6 CONNECTOR AS505151
KPTM 18 ITT CANNON MIL-DTL-83723 SERIES I M81511/36 16 MILITARY MIL-DTL--81511 SERIES 1 & 3
FZH 19 FLIGHT MIL-C-83723 SERIES II KS* 9 ITT CANNON MIL-DTL-26482 SERIES 1 & 2 M81511/37 16 MILITARY MIL-DTL--81511 SERIES 1 & 3
CONNECTOR
KS* 18 ITT CANNON MIL-DTL-83723 SERIES I M81511/38 16 MILITARY MIL-DTL--81511 SERIES 1 & 3
G 12 CONNECTOR MIL-C-38999 SERIES I
INDUSTRIES KSP 9 ITT CANNON MIL-DTL-26482 SERIES 1 & 2 M81511/41 16 MILITARY MIL-DTL--81511 SERIES 1 & 3
CONNECTOR KSP 18 ITT CANNON MIL-DTL--83723 SERIES I M81511/42 16 MILITARY MIL-DTL--81511 SERIES 1 & 3
G 13 INDUSTRIES MIL-DTL--38999 SERIES II
KSPM 9 ITT CANNON MIL-DTL--26482 SERIES 1 & 2 M81511/44 16 MILITARY MIL-DTL-81511 SERIES 1 & 3
GB 9 GLASSEAL MIL-DTL--26482 SERIES 1 & 2 KSPM 18 ITT CANNON MIL-DTL--83723 SERIES I M81511/45 16 MILITARY MIL-DTL-81511 SERIES 1 & 3
GB 18 GLASSEAL MIL-DTL--83723 SERIES I M81511/46 16 MILITARY MIL-DTL-81511 SERIES 1 & 3
KSSE 9 ITT CANNON MIL-DTL--26482 SERIES 1 & 2
GC 9 GENERAL MIL-DTL--26482 SERIES 1 & 2 M81511/47 16 MILITARY MIL-DTL-81511 SERIES 1 & 3
CONNECTOR KSSE 18 ITT CANNON MIL-DTL--83723 SERIES I
M81511/48 16 MILITARY MIL-DTL-81511 SERIES 1 & 3
GENERAL L*T 9 BURNDY MIL-DTL--26482 SERIES 1 & 2
GC 18 CONNECTOR MIL-DTL--83723 SERIES I M81511/49 16 MILITARY MIL-DTL-81511 SERIES 1 & 3
L*T 18 BURNDY MIL-DTL--83723 SERIES I
GENERAL M81511/50 17 MILITARY MIL-DTL-81511 SERIES 2 & 4
GC*C 9 MIL-DTL--26482 SERIES 1 & 2 LCT 12 PLESSEY MIL-DTL--38999 SERIES I
CONNECTOR M81511/51 17 MILITARY MIL-DTL-81511 SERIES 2 & 4
LJT 12 AMPHENOL MIL-DTL--38999 SERIES I
GC*C 18 GENERAL MIL-DTL--83723 SERIES I M81511/52 17 MILITARY MIL-DTL-81511 SERIES 2 & 4
CONNECTOR LM*C 6 BURNDY AS50151
M81511/53 17 MILITARY MIL-DTL-81511 SERIES 2 & 4
GS 6 ITT CANNON AS505151 LM*C 19 BURNDY MIL-DTL-83723 SERIES II
M81511/54 17 MILITARY MIL-DTL-81511 SERIES 2 & 4
GS 11 HUGHES MIL-DTL-28840 M0 6 IPI (SEA) AS505151
M81511/55 17 MILITARY MIL-DTL-81511 SERIES 2 & 4
GS 19 ITT CANNON MIL-DTL-83723 SERIES II M0 19 IPI (SAE) MIL-DTL-83723 SERIES II
M81511/56 17 MILITARY MIL-DTL-81511 SERIES 2 & 4
GSP 6 GLASSEAL AS5015 M28840/10 11 MILITARY MIL-DTL--28840
M81511/57 17 MILITARY MIL-DTL-81511 SERIES 2 & 4
GSP 19 GLASSEAL MIL-DTL--83723 SERIES II M28840/11 11 MILITARY MIL-DTL--28840
M83723/01 18 MILITARY MIL-DTL--83723 SERIES I
GT 11 HUGHES MIL-DTL--28840 M28840/12 11 MILITARY MIL-DTL--28840
M83723/02 18 MILITARY MIL-DTL--83723 SERIES I
CONNECTOR M28840/16 11 MILITARY MIL-DTL--28840
H 13 INDUSTRIES MIL-DTL--38999 SERIES II M83723/03 18 MILITARY MIL-DTL--83723 SERIES I
M28840/16 11 MILITARY MIL-DTL--28840
HD 11 IPI (SAE) MIL-DTL--28840 M83723/04 18 MILITARY MIL-DTL--83723 SERIES I
M28840/17 11 MILITARY MIL-DTL--28840
 MIL-DTL--22992 CLASSES M83723/05 18 MILITARY MIL-DTL--83723 SERIES I
HK 7 AMPHENOL C, J, R M28840/18 11 MILITARY MIL-DTL--28840
M83723/06 18 MILITARY MIL-DTL--83723 SERIES I
M28840/19 11 MILITARY MIL-DTL--28840
HM SERIES 12 IPI (SAE) MIL-DTL--38999 SERIES I M83723/07 18 MILITARY MIL-DTL--83723 SERIES I
M28840/20 11 MILITARY MIL-DTL--28840
M83723/08 18 MILITARY MIL-DTL--83723 SERIES I
M28840/21 11 MILITARY MIL-DTL--28840
HM SERIES 13 IPI (SAE) MIL-DTL--38999 SERIES II M83723/09 18 MILITARY MIL-DTL--83723 SERIES I
M28840/26 11 MILITARY MIL-DTL--28840
HERMETIC M83723/10 18 MILITARY MIL-DTL--83723 SERIES I
HS06 6 SEAL CORP. AS50151 M28840/28 11 MILITARY MIL-DTL--28840
M83723/11 18 MILITARY MIL-DTL--83723 SERIES I
M28840/29 11 MILITARY MIL-DTL--28840
HS06 19 HERMETIC MIL-DTL-83723 SERIES II M83723/12 18 MILITARY MIL-DTL--83723 SERIES I
SEAL CORP. M5 6 IPI (SAE) AS505151
M83723/13 18 MILITARY MIL-DTL--83723 SERIES I
HT 6 AMPHENOL AS50151 M5 19 IPI (SAE) MIL-DTL-83723 SERIES II
M83723/16 18 MILITARY MIL-DTL--83723 SERIES I
HT 19 AMPHENOL MIL-DTL-83723 SERIES II MATRIX
M723 6 SCIENCE AS505151 M83723/17 19 MILITARY MIL-DTL--83723 SERIES II
HTMF 10 ITT CANNON MIL-DTL-26500
MATRIX M83723/18 19 MILITARY MIL-DTL--83723 SERIES II
HTMF 20 ITT CANNON MIL-DTL-83723 SERIES III M723 19 SCIENCE MIL-DTL--83723 SERIES II
M83723/19 19 MILITARY MIL-DTL--83723 SERIES II
JT 13 AMPHENOL MIL-DTL-38999 SERIES II
M81511/01 17 MILITARY MIL-DTL--81511 SERIES 2 & 4 M83723/20 19 MILITARY MIL-DTL--83723 SERIES II
K 9 CONNECTOR MIL-DTL-26482 SERIES 1 & 2 M81511/02 17 MILITARY MIL-DTL--81511 SERIES 2 & 4
INDUSTRIES M83723/21 19 MILITARY MIL-DTL--83723 SERIES II
M81511/03 17 MILITARY MIL-DTL--81511 SERIES 2 & 4 M83723/22 19 MILITARY MIL-DTL--83723 SERIES II
K 18 CONNECTOR MIL-DTL-83723 SERIES I
INDUSTRIES M81511/04 17 MILITARY MIL-DTL--81511 SERIES 2 & 4 M83723/23 19 MILITARY MIL-DTL--83723 SERIES II
KFS 11 ITT CANNON MIL-DTL-28840 M81511/05 17 MILITARY MIL-DTL--81511 SERIES 2 & 4 M83723/24 19 MILITARY MIL-DTL--83723 SERIES II
KJ 13 ITT CANNON MIL-DTL-38999 SERIES II M81511/06 17 MILITARY MIL-DTL--81511 SERIES 2 & 4 M83723/25 19 MILITARY MIL-DTL--83723 SERIES II
KJA 14 ITT CANNON MIL-DTL-38999 SERIES III M81511/21 16 MILITARY MIL-DTL--81511 SERIES 1 & 3 M83723/26 19 MILITARY MIL-DTL--83723 SERIES II
KJJ 13 ITT CANNON MIL-DTL-38999 SERIES II M81511/22 16 MILITARY MIL-DTL--81511 SERIES 1 & 3 M83723/36 18 MILITARY MIL-DTL--83723 SERIES I
KJJL 12 ITT CANNON MIL-DTL-38999 SERIES I M81511/23 16 MILITARY MIL-DTL--81511 SERIES 1 & 3 M83723/37 18 MILITARY MIL-DTL--83723 SERIES I
KJL 12 ITT CANNON MIL-DTL-38999 SERIES I M81511/24 16 MILITARY MIL-DTL--81511 SERIES 1 & 3 M83723/38 18 MILITARY MIL-DTL--83723 SERIES I
KP* 9 ITT CANNON MIL-DTL-26482 SERIES 1 & 2 M81511/25 16 MILITARY MIL-DTL--81511 SERIES 1 & 3 M83723/39 18 MILITARY MIL-DTL--83723 SERIES I
KP* 18 ITT CANNON MIL-DTL-83723 SERIES I M81511/26 16 MILITARY MIL-DTL--81511 SERIES 1 & 3 M83723/40 18 MILITARY MIL-DTL--83723 SERIES I
KPD 9 ITT CANNON MIL-DTL-26482 SERIES 1 & 2 M81511/27 16 MILITARY MIL-DTL--81511 SERIES 1 & 3 M83723/41 18 MILITARY MIL-DTL--83723 SERIES I
KPD 18 ITT CANNON MIL-DTL-83723 SERIES I M81511/28 17 MILITARY MIL-DTL--81511 SERIES 2 & 4 M83723/42 18 MILITARY MIL-DTL--83723 SERIES I
KPSE 9 ITT CANNON MIL-DTL-26482 SERIES 1 & 2 M81511/31 17 MILITARY MIL-DTL--81511 SERIES 2 & 4 M83723/43 18 MILITARY MIL-DTL--83723 SERIES I
KPSE 18 ITT CANNON MIL-DTL-83723 SERIES I M81511/32 17 MILITARY MIL-DTL--81511 SERIES 2 & 4 M83723/48 18 MILITARY MIL-DTL--83723 SERIES I
KPT 9 ITT CANNON MIL-DTL-26482 SERIES 1 & 2 M81511/33 17 MILITARY MIL-DTL--81511 SERIES 2 & 4 M83723/49 18 MILITARY MIL-DTL--83723 SERIES I
KPT 18 ITT CANNON MIL-DTL-83723 SERIES I M81511/34 17 MILITARY MIL-DTL--81511 SERIES 2 & 4 M83723/52 19 MILITARY MIL-DTL--83723 SERIES II

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 35
CONNECTOR
IDENTIFICATION
CONNECTOR SERIES CONNECTOR SERIES CONNECTOR SERIES
PREFIX PAGE MANUFACTURER PREFIX PAGE MANUFACTURER PREFIX PAGE MANUFACTURER
(REFERENCE) (REFERENCE) (REFERENCE)
M83723/53 19 MILITARY MIL-DTL--83723 SERIES II MR 6 ITT CANNON AS505151 MS27616 10 MILITARY MIL-DTL-26500
M83723/65 20 MILITARY MIL-DTL--83723 SERIES III MR 19 ITT CANNON MIL-DTL-83723 SERIES II MS27615 10 MILITARY MIL-DTL-26500
M83723/66 20 MILITARY MIL-DTL--83723 SERIES III
MS17343 7 MILITARY MIL-DTL-22992 MS27652 12 MILITARY MIL-DTL-38999 SERIES I
M83723/67 20 MILITARY MIL-DTL--83723 SERIES III CLASSES C, J, R
MS27653 12 MILITARY MIL-DTL-38999 SERIES I
M83723/68 20 MILITARY MIL-DTL--83723 SERIES III MIL-DTL-22992
MS17344 7 MILITARY CLASSES C, J, R MS27654 12 MILITARY MIL-DTL-38999 SERIES I
M83723/69 20 MILITARY MIL-DTL--83723 SERIES III
MS17345 7 MILITARY MIL-DTL-22992 MS27656 12 MILITARY MIL-DTL-38999 SERIES I
M83723/71 20 MILITARY MIL-DTL-83723 SERIES III CLASSES C, J, R
M83723/72 20 MILITARY MIL-DTL-83723 SERIES III MS27661 12 MILITARY MIL-DTL-38999 SERIES I
MS17346 7 MILITARY MIL-DTL-22992
CLASSES C, J, R MS27662 12 MILITARY MIL-DTL-38999 SERIES I
M83723/73 20 MILITARY MIL-DTL-83723 SERIES III
MS17347 7 MILITARY MIL-DTL-22992 MS27664 13 MILITARY MIL-DTL-38999 SERIES II
M83723/74 20 MILITARY MIL-DTL-83723 SERIES III CLASSES C, J, R
M83723/75 20 MILITARY MIL-DTL-83723 SERIES III MIL-DTL-22992 MS3100 6 MILITARY AS505151
MS17348 7 MILITARY CLASSES C, J, R
M83723/76 20 MILITARY MIL-DTL-83723 SERIES III MS3101 6 MILITARY AS505151
MS24264 10 MILITARY MIL-DTL-26500 MS3102 6 MILITARY AS505151
M83723/77 20 MILITARY MIL-DTL-83723 SERIES III
MS24265 10 MILITARY MIL-DTL-26500 MS3103 6 MILITARY AS505151
M83723/78 20 MILITARY MIL-DTL-83723 SERIES III
MS24266 10 MILITARY MIL-DTL-26500 MS3106 6 MILITARY AS505151
M83723/79 20 MILITARY MIL-DTL-83723 SERIES III
MS24183 6 MILITARY AS505151 MS3107 6 MILITARY AS505151
M83723/80 20 MILITARY MIL-DTL-83723 SERIES III
MS25183A 6 MILITARY AS505151 MS3108 6 MILITARY AS505151
M83723/81 20 MILITARY MIL-DTL-83723 SERIES III
MS27034 10 MILITARY MIL-DTL-26500 MS3120 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
M83723/82 20 MILITARY MIL-DTL-83723 SERIES III
MS27466 12 MILITARY MIL-DTL-38999 SERIES I MS3121 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
M83723/83 20 MILITARY MIL-DTL-83723 SERIES III
MS27467 12 MILITARY MIL-DTL-38999 SERIES I MS3122 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
M83723/84 20 MILITARY MIL-DTL-83723 SERIES III
M83723/85 20 MILITARY MIL-DTL-83723 SERIES III MS27468 12 MILITARY MIL-DTL-38999 SERIES I MS3124 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
M83723/86 20 MILITARY MIL-DTL-83723 SERIES III MS27469 12 MILITARY MIL-DTL-38999 SERIES I MS3126 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
M83723/87 20 MILITARY MIL-DTL-83723 SERIES III MS27470 12 MILITARY MIL-DTL-38999 SERIES I MS3127 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
M83723/88 20 MILITARY MIL-DTL-83723 SERIES III MS27471 12 MILITARY MIL-DTL-38999 SERIES I MS3128 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
M83723/89 20 MILITARY MIL-DTL-83723 SERIES III MS27472 13 MILITARY MIL-DTL-38999 SERIES II MS3142 6 MILITARY AS505151
M83723/90 20 MILITARY MIL-DTL-83723 SERIES III MS27473 13 MILITARY MIL-DTL-38999 SERIES II MS3143 6 MILITARY AS505151
M83723/91 20 MILITARY MIL-DTL-83723 SERIES III MS27474 13 MILITARY MIL-DTL-38999 SERIES II MS3400 6 MILITARY AS505151
M83723/92 20 MILITARY MIL-DTL-83723 SERIES III MS27475 13 MILITARY MIL-DTL-38999 SERIES II MS3401 6 MILITARY AS505151
M83723/93 20 MILITARY MIL-DTL-83723 SERIES III MS27476 13 MILITARY MIL-DTL-38999 SERIES II MS3402 6 MILITARY AS505151
M83723/94 20 MILITARY MIL-DTL-83723 SERIES III MS27477 13 MILITARY MIL-DTL-38999 SERIES II MS3404 6 MILITARY AS505151
M83723/95 20 MILITARY MIL-DTL-83723 SERIES III MS27478 13 MILITARY MIL-DTL-38999 SERIES II MS3406 6 MILITARY AS505151
M83723/96 20 MILITARY MIL-DTL-83723 SERIES III MS27479 13 MILITARY MIL-DTL-38999 SERIES II MS3408 6 MILITARY AS505151
M83723/97 20 MILITARY MIL-DTL-83723 SERIES III MS27480 13 MILITARY MIL-DTL-38999 SERIES II MS3409 6 MILITARY AS505151
M83723/98 20 MILITARY MIL-DTL-83723 SERIES III MS27481 13 MILITARY MIL-DTL-38999 SERIES II MS3412 6 MILITARY AS505151
MB1 9 MATRIX MIL-DTL-26482 SERIES 1 & 2 MS27482 13 MILITARY MIL-DTL-38999 SERIES II
SCIENCE MS3436 6 MILITARY AS505151
MS27483 13 MILITARY MIL-DTL-38999 SERIES II MS3440 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
MB1 18 MATRIX MIL-DTL-83723 SERIES I
SCIENCE MS27484 13 MILITARY MIL-DTL-38999 SERIES II MS3442 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
MB3 10 MATRIX MIL-DTL-26500 MS27496 12 MILITARY MIL-DTL-38999 SERIES I
SCIENCE MS3443 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
MS27497 13 MILITARY MIL-DTL-38999 SERIES II MS3447 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
MB3 20 MATRIX MIL-DTL-83723 SERIES III
SCIENCE MS27498 12 MILITARY MIL-DTL-38999 SERIES I
MS3450 6 MILITARY AS505151
MB91 12 MATRIX MIL-DTL-38999 SERIES I MS27499 13 MILITARY MIL-DTL-38999 SERIES II
SCIENCE MS3451 6 MILITARY AS505151
MATRIX MIL-DTL-38999 SERIES II MS27500 13 MILITARY MIL-DTL-38999 SERIES II
MB92 13 MS3452 6 MILITARY AS505151
SCIENCE
MS27503 13 MILITARY MIL-DTL-38999 SERIES II
MS3454 6 MILITARY AS505151
MFR 6 MATRIX AS505151
SCIENCE MS27504 13 MILITARY MIL-DTL-38999 SERIES II
MS3456 6 MILITARY AS505151
MATRIX MIL-DTL-83723 SERIES II MS27505 12 MILITARY MIL-DTL-38999 SERIES I
MFR 19 SCIENCE MS3459 6 MILITARY AS505151
MS27508 13 MILITARY MIL-DTL-38999 SERIES II
MATRIX MIL-DTL-22992 CLASS L MS3470 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
MHD 8 SCIENCE MS27513 13 MILITARY MIL-DTL-38999 SERIES II
MS3471 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
ML94 15 MATRIX MIL-DTL-38999 SERIES IV MS27515 12 MILITARY MIL-DTL-38999 SERIES I
SCIENCE MS3472 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
MS27613 10 MILITARY MIL-DTL-26500
MMB 10 CINCH MIL-DTL-26500

PAGE 36 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 CONNECTOR SERIES CONNECTOR SERIES CONNECTOR SERIES
PREFIX PAGE MANUFACTURER PREFIX PAGE MANUFACTURER PREFIX PAGE MANUFACTURER
(REFERENCE) (REFERENCE) (REFERENCE)

MS3473 9 MILITARY MIL-DTL-26482 SERIES 1 & 2 PVJ 9 ITT CANNON MIL-C-26482 SERIES 1 & 2 SP 18 AMPHENOL MIL-C-83723 SERIES I
MS3474 9 MILITARY MIL-DTL-26482 SERIES 1 & 2 PVJ 18 ITT CANNON MIL-C-83723 SERIES I SP*CE 9 AMPHENOL MIL-C-26482 SERIES 1 & 2
MS3475 9 MILITARY MIL-DTL-26482 SERIES 1 & 2 PVW 9 ITT CANNON MIL-C-26482 SERIES 1 & 2 SP*CE 18 AMPHENOL MIL-C-83723 SERIES I
MS3476 9 MILITARY MIL-DTL-26482 SERIES 1 & 2 PVW 18 ITT CANNON MIL-C-83723 SERIES I PYLE-
T3 14 NATIONAL MIL-C-38999 SERIES III
MS3477 9 MILITARY MIL-DTL-26482 SERIES 1 & 2 PVX 9 ITT CANNON MIL-C-26482 SERIES 1 & 2
PVX 18 ITT CANNON MIL-C-83723 SERIES I TBF 6 AMPHENOL AS505151
MS3479 9 MILITARY MIL-DTL-26482 SERIES 1 & 2
MS3507 6 MILITARY AS505151 PVX 21 CANNON PATTERN 602 TBF 6 ITT CANNON AS505151
ELECTRIC GB
TBF 19 AMPHENOL MIL-C-83723 SERIES II
MS90555 8 MILITARY MIL-C-22992 CLASS L PW 9 S.E.C. MIL-C-26482 SERIES 1 & 2
TBF 19 ITT CANNON MIL-C-83723 SERIES II
PW 18 S.E.C. MIL-C-83723 SERIES I
MS90556 8 MILITARY MIL-C-22992 CLASS L TBFH 6 ITT CANNON AS505151
QWLD 7 AMPHENOL  MIL-C-22992 CLASSES
MS90557 8 MILITARY MIL-C-22992 CLASS L C, J, R TBFH 19 ITT CANNON MIL-C-83723 SERIES II
MS90558 8 MILITARY MIL-C-22992 CLASS L RBC 9 DEUTSCH/TE MIL-C-26482 SERIES 1 & 2
TCT 14 PLESSEY MIL-C-38999 SERIES III
MT3 10 MATRIX MIL-C-26500 RBC 18 DEUTSCH/TE MIL-C-83723 SERIES I
SCIENCE TV 14 AMPHENOL MIL-C-38999 SERIES III
RR 21 HELLERMANN PATTERN 602
MATRIX DEUTSCH/TE VE 6 VEAM/LITTON AS505151
MT3 20 SCIENCE MIL-C-83723 SERIES III
HERMETIC VE 19 VEAM/LITTON AS505151
MATRIX S*A-2000 6 SEAL CORP. AS505151
MT93 14 SCIENCE MIL-C-38999 SERIES III VG 6 VEAM/LITTON AS505151
S*A-2000 19 HERMETIC MIL-C-83723
NC 11  G&H MIL-C-28840 SEAL CORP. SERIES II. VPT 9 VEAM/LITTON MIL-C-26482 SERIES 1 & 2
TECHNOLOGY
S*A-7000 9 HERMETIC MIL-C-26482 VPT 18 VEAM/LITTON MIL-C-83723 SERIES I
P 12 CONNECTOR MIL-C-38999 SERIES I SEAL CORP. SERIES 1 & 2 .
INDUSTRIES VPT*SE 9 VEAM/LITTON MIL-C-26482 SERIES 1 & 2
S*A-7000 18 HERMETIC MIL-C-83723 SERIES I
PL 15 FLIGHT MIL-C-38999 SERIES IV SEAL CORP. VPT*SE 18 VEAM/LITTON MIL-C-83723 SERIES I
CONNECTOR
SA 6 IPI (SAE) AS505151 VS 6 VEAM/LITTON AS505151
PT 9 AMPHENOL MIL-C-26482 SERIES 1 & 2
SA 19 IPI (SAE) MIL-C-83723 SERIES II VS 19 VEAM/LITTON MIL-C-83723 SERIES II
PT 18 AMPHENOL MIL-C-83723 SERIES I
SCP 6 AMPHENOL AS505151 VTBF 6 VEAM/LITTON AS505151
PT*CE 9 AMPHENOL MIL-C-26482 SERIES 1 & 2
SCP 19 AMPHENOL MIL-C-83723 SERIES II VTBF 19 VEAM/LITTON MIL-C-83723 SERIES II
PT*CE 18 AMPHENOL MIL-C-83723 SERIES I
SERIES I 12 ELECTRONIC MIL-C-38999 SERIES I VUT 9 VEAM/LITTON MIL-C-28482 SERIES 1 & 2
PT*SE 9 AMPHENOL MIL-C-26482 SERIES 1 & 2 SEALS
PT*SE 18 AMPHENOL MIL-C-83723 SERIES I ELECTRONIC VUT 18 VEAM/LITTON MIL-C-83723 SERIES I
SERIES II 13 SEALS MIL-C-38999 SERIES II
PTS*DR 9 AMPHENOL MIL-C-26482 SERIES 1 & 2 WFS 6 ITT CANNON AS505151
SERIES III 14 ELECTRONIC MIL-C-38999 SERIES III
PTS*DR 18 AMPHENOL MIL-C-83723 SERIES I SEALS WFS 19 ITT CANNON MIL-C-83723 SERIES II
PV 9 ITT CANNON MIL-C-26482 SERIES 1 & 2 ELECTRONIC
SERIES IV 15 SEALS MIL-C-38999 SERIES IV PYLE- MIL-C-26500
PV 18 ITT CANNON MIL-C-83723 SERIES I ZZ 10 NATIONAL
PVA 9 ITT CANNON MIL-C-26482 SERIES 1 & 2 SJT 22 AMPHENOL SJT

PVA 18 ITT CANNON MIL-C-83723 SERIES I SP 9 AMPHENOL MIL-C-26482 SERIES 1 & 2

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 37
CONNECTOR MATE ®

ASSEMBLY VISE

The continuing demands of electrical

system designers have imposed
such rapid development in the field of
interconnection technology that new
and different hardware is emerging to
meet those demands. Along with the
introduction of these new, and often more
complex connectors and accessories,
the challenge for versatile and reliable
production tooling becomes apparent.
To this end, DMC has accepted the
challenge by developing the assembly
station vise which provides a reliable
and repeatable holding method for
countless combinations of connectors
and accessories. The use of removable
soft-grip jaw inserts allows the vise to
easily accommodate all popular connector
diameters.
This is a reliable method of r­etaining
circular parts, which avoids damage to
critical platings and retains the circular
shape of delicate parts.

PAGE 38
 ADJUSTABLE STOP: An added
feature for convenience and efficiency
of operation is the adjustable stop
on the vise. This provides for extra
gripping stability and a repeatable
reference for production line
applications.
JAW SETS
A set of jaws is designed to
HOW THE ASSEMBLY accommodate diameters from .375″ to
If the force is applied on opposite
VISE WORKS 3.00″ (3/8″ to 3″), within six different
sides (only two pressure points), the
The system consists of non- jaw sizes. This provides for flexibility of
circular part will tend to collapse, and
marring jaw inserts and a specially application — the same system can
this will produce false torque readings
designed vise to hold them. They be used for most or all of the c­ ircular
because of increased friction between
can be used to hold any circular connectors and accessories in a cable
the components where the threads
part within the size range available, assembly operation.
have been forced together.
including connectors, backshell Jaws are available in two gripping
A square drive on the thread
accessories and adaptor tools. ­handle allows the use of a torque
In a conventional vise, one jaw device to minimize the possibility of
is stationary, while the other moves on overtightening.
the thread mechanism. The assembly The position of the jaw inserts in
station vise is different in that it the vise can be changed to hold the
employs an opposing thread design work in the most convenient location
— that is, both jaws move in syn­ for assembly.
chro­niza­­tion. This design has several The jaw inserts come packaged in
advantages for connector assembly: a convenient metal container which
FAST TIGHTENING: A part can be
secured faster, which is a benefit to
­production procedures. widths — .400″ and 1.000″.
HIGH STRENGTH: A substantial The narrow jaws allow access to
increase in strength and thread life accessories which are smaller in
is achieved by the double-thread diameter than adjacent components,
arrangement. whereas the wider jaws allow for a
SELF-CENTERING: Because the large grip area when higher torque
jaws move towards each other, the values are required.
work is always centered in the vise, Jaws are made from high-friction
and therefore, lateral stress and unnec­ material which will not damage c ­ on­
essary movement of the work pieces nectors or accessories, yet will provide
keeps them clean, orderly and readily
are not introduced into the process. sufficient grip for most operations.
available for use. Instructions are
Prevents deformation of circular
also provided for their proper use.
connectors and accessories by
There are twelve pairs of jaw inserts
applying holding pressure evenly at
in the container which accommodate
four points on the circumference.
diameters from 3/8″ to 3″.
That is, the jaws apply a force radially
at four points equally spaced around
the ­circumference such that the
circular part readily accepts it without
ASSEMBLY VISE
deformation.
ASSEMBLY VISE WITH 24-PIECE
BT-VS-511
SET OF JAW INSERTS
ASSEMBLY VISE ONLY
BT-VS-500
(WITHOUT JAW INSERTS)
24-PIECE SET OF JAW INSERTS,
BT-S-550 FOR USE WITH VISE BT-VS-500

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 39
DIGITAL TORQUE WRENCH

BT-ST-302D BT-ST-302DR

Reverse Head

Higher torque ratings to meet mechanical fastening Several features of the tool make it a great addition to the
specifications for self-locking threads, and the need for DMC BETA™ Connector Accessory Tool product line.
improved electrical bonding, have fostered the need for an
improved Torque Tightening System. DMC has responded • CW or CCW ratcheting drive
to that need with a unique Digital Torque System that is • Visual and/or audible indication when the force torque reaches
rugged, versatile, and easy to use. This highly repeatable 40%, 60%, 80%, 100%, and 104% of the set torque
Digital Torque System can be easily used with other BETA™ • Modes: Preset, Track or Peak for Torque, and Angle Mode
Connector Accessory Tools to maintain precise tightening • Data storage of last 1,500 torque values
consistency through every facet of wiring system final • USB interface (cable included)
assembly. • Data Download: 302D is exported as a common CSV file that can
be read in common spreadsheet software (i.e., Microsoft Excel)
Many times, torque is only thought of as a means to prevent
• Auto Turn-Off/Low Battery display
an assembly from loosening under vibration or other external
• Splash-Proof, protected against water & moisture, metal
forces. However, in the present environment, it is equally
important not to over-tighten an assembly risking damage to components are chrome plated for maximum corrosion resistance
plating, threads, or fastening components made of metal and/ • Ruggedized, withstands drops and rough handling without failure
or composite materials. Such damage may increase the risk • 1/4” drive adaptor included
of failure, and/or cause a reduced service life of the wiring • Standard AA battery (1 battery is included)
system. • Torque overload display and audible signal
• ISO-6789-203 and ASME B107-28-2005 Standards Compliant
DMC’s BT-ST-302D Digital Torque Tool provides OEMs and
field service technicians with
a simple and efficient way
to precisely measure torque
values. This state-of-the-
art product was developed
specifically to meet the
demands of connector final
assembly. A Reverse Head
model is also available Part
Number BT-ST-302DR.

An optional bench mount is available Part Number BM-302D which can be configured in a vertical or horizontal position for use with BT-ST-302DR

HAND-HELD DIGITAL TORQUE TOOLS TORQUE ACCURACY

BT-ST-302D
DIGITAL TORQUE TOOL, Accuracy
12 - 240 INCH POUNDS in-lb ft-lb kg-cm N-m dNm
(Reading)
ADAPTER – 3/8” DRIVE TO CW +/-2%
BT-D-0551 48-240 4 - 20 55.3 - 276.5 5.4 - 27.1 54.2 - 271.2
1/4” SOCKET (Included) CCW +/-3%
REVERSE HEAD DIGITAL TORQUE TOOL, CW +/-4%
BT-ST-302DR 12 - 45.6 1 - 3.8 13.8 - 52.5 1.4 - 5.2 13.6 - 51.5
12 - 240 INCH POUNDS CCW +/-6%
BENCH MOUNT (Optional) for use ONLY
BM-302D
with BT-ST-302DR

PAGE 40 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
DIGITAL TORQUE TOOL ACCESSORIES

Strap wrench

Connector Adaptor

BT-ST-302D

Adapter 3/8” to 1/4”

Strap Wrench Attachment for the Digital Torque Tool

DMC’s handle-less strap wrench (pictured below) line has

been specifically designed for torque accurate connector
assembly. Based on DMC’s established line of torque
wrenches, the handle-less strap wrench attaches to the
BT-ST-302D and provides accurate torque without the
interference of the strap wrench handle.

Modern connectors and accessories comprised of

lightweight materials, torque sensitive threads, and critical
platings have mandated the requirement for precision
strap wrenches. DMC Strap Wrenches meet this need by
applying a uniform grip around the diameter and avoid
pressure points or metal-to-metal contact.

Yellow - First light indicates 40% of target torque or angle reached. A variety of widths and lengths of straps are available,
Second indicates 60% of target reached. Third indicates 80% of target reached. in several different head configurations, so the system is
suited to all common connector applications. See our web
site at www.dmctools.com for a full list of strap wrench
part numbers.

NOTE: Torque correction is required when using strap

wrench extensions. Information available from DMC.

Green - Indicates target torque or angle reached.

HANDLE-LESS STRAP WRENCH

Part Strap Gripping
Number Width Diameter
BT-BS-609T 1/2” .50”to 2.50”
BT-BS-610T * 1/2” .25” to 1.50”
BT-BS-611T 5/8” 1.00” to 4.00”
Red - Indicates exceeded torque or angle target plus 4% or exceeded
maximum preset target. BT-BS-618T 1” 1.00” to 4.00” Handle-less strap wrench

*Profile for small diameters

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 41
STRAP WRENCHES

DMC strap wrenches have been STANDARD STRAP WRENCHES

specifically designed for connector TOOL SUGGESTED
WRENCH STRAP STRAP WIDTH STRAP
assembly, rather than merely adapted TIP
P/N P/N (COLOR) LOOPED
GRIPPING
STYLE DIAMETER
from another use. The combination of
lightweight materials, torque sensitive BT-BS-610 BT-A-6010 1/2"″ (Black) Yes .25"″ to 1.50"″
threads, and critical platings on modern BT-BS-610B* BT-A-6010B* 1/2"″ (Blue) Yes .25"″ to 1.50"″
A
connectors has mandated the requirement BT-BS-610W BT-A-6010W 1/2"″ (White) Yes .25"″ to 1.50"″
for precision-made strap wrenches, which BT-BS-610R BT-A-6010R 1/2"″ (Red) Yes .25"″ to 1.50"″
apply a uniform grip around the diameter
BT-BS-609 BT-A-6010 1/2"″ (Black) Yes .50"″ to 2.50"
and avoid pressure points or metal-to-
BT-BS-609B* BT-A-6010B* 1/2"″ (Blue) Yes .50"″ to 2.50"″
metal contact. B
A variety of widths and lengths of straps BT-BS-609W BT-A-6010W 1/2"″ (White) Yes .50"″ to 2.50"″
is available, in several different handle BT-BS-609R BT-A-6010R 1/2"″ (Red) Yes .50"″ to 2.50"″
configurations, so the system is suited to BT-BS-611 BT-A-6175 5/8"″ (Black) Yes 1.00"″ to 4.00"
all common connector applications. C BT-BS-611B* BT-A-6175B* 5/8"″ (Blue) Yes 1.00"″ to 4.00"″
BT-BS-611W BT-A-6175W 5/8"″ (White) Yes 1.00"″ to 4.00"″

BT-BS-618 BT-A-6185 1"″ (Black) Yes 1.00"″ to 4.00"″

C BT-BS-618B* BT-A-6185B* 1"″ (Blue) Yes 1.00"″ to 4.00"″
BT-BS-618W BT-A-6185W 1"″ (White) Yes 1.00"″ to 4.00"″
BT-BS-625 BT-A-6250 1/2"″ (Red) Yes .50"″ to 2.0"″
D
BT-BS-630 BT-A-6300 7/16"″ (Black) Yes .50"″ to 2.0"″
E The Handle-Less Strap Wrenches are presented on page 45.

*The blue series strap wrench and replacement straps are preferred for connector/accessory use.

SEE TORQUE CONVERSION CHARTS ON PAGE 47 FOR USE OF STRAP

WRENCHES AND TORQUE MEASUREMENT TOOLS.

E
D

PAGE 42 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
STRAPS
STRAP WRENCH SIZES
The straps for DMC Strap Wrenches
are available in four styles (which are
color coded for easy identification) to
better meet the needs of individual
applications. A
The Black Strap is the traditional rubber strap for DMC strap wrenches.
It is the most flexible and grip-friendly of all strap materials, but requires
replacement more often than other strap constructions. It is good for all sizes,
and flexible enough to grip smaller diameters (.25 to .75 inches). But the black
strap is not recommended for high torque range tightening. It is available
in looped and loopless configurations. Because of the shorter service life B
of this material, we recommend the loopless version so the user can make
adjustments to compensate for wear or breakage.

The Blue Strap is made of a thin layer of extruded polyethylene over a

nylon belt. This strap is the preferred choice for all general purpose connector
and backshell tightening applications, and it has good service life at medium
to high-medium torque ranges. The Blue Straps, although not as flexible and
grip-friendly as the Black Rubber straps, are a good choice because of the
increased durability. This strap will grip .75 inch diameters and larger, and is C
available in looped and loopless configurations.

The White Strap is a traditional hard rubber construction option that has a
durable rubber surface on one side. It is used effectively where high strength
is needed, but flexibility is not important. It is well suited to all diameters of 2.0
inches or larger. Due to its sturdy & thick construction, the white strap is only A: The BT-BS-610 Series tool tip is
available in looped configuration. our small-diameter tip and designed
to accommodate connectors and
The Red Strap is the same material and construction as the Blue Strap, backshells with diameters from .25 to
but it is thicker and stronger for higher torque range tightening and increased 1.5 inches. Straps are .5 an inch wide.
durability. This heavy duty construction allows it to be used on smooth or
knurled surfaces, and can be used to tighten fittings with 1.0 inch diameters B: The BT-BS-609 Series tool tip is
and larger. It is available in looped and loopless versions. our most popular choice for general
purpose use. The mid-diameter tip is
designed to accommodate connectors
NOTE: Strap length and width are important considerations in selecting and backshells with diameters from
a strap wrench and the replacement straps. Sometimes Grip Pads are .5 to 2.50 inches. Straps are .5 an
recommended for use with strap wrenches to add traction while tightening inch wide.
some surfaces. If you have any questions about the best combination for your
application, contact DMC. C: The BT-BS-611 Series tool tip
is our large-diameter tip designed
to accommodate connectors and
STRAP COLORS STRAP CONFIGURATIONS
backshells with diameters from 1 to
COLOR
SMALL MEDIUM LARGE TORQUE LOOPLESS
LOOPED LOOPLESS 4 inches. Straps are 5/8 an inch wide.
DIAMETERS DIAMETERS DIAMETERS RANGE AVAILABLE

Black X X X Med X D: (NOT PICTURED) The BT-BS-618

Series tool tip is also a large-diameter
Med-
Blue* X X X
High
X tip like the BT-BS-611 designed
to accommodate connectors and
Red X X High X backshells with diameters from 1 to
4 inches, but with a 1 inch wide strap
White X X High for better gripping and applying higher
*The blue straps are preferred for connector/accessory use. torque values.

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 43
LOOPLESS-STRAP WRENCH

All straps wear and break. The most common point of wear is at the upper
edge of the tool tip, near the base of the strap. The standard straps have a LOOPLESS STRAP ­INSTALLATION
loop sewn into one end and attach to the wrench body with a simple link.
However, when the strap eventually breaks, it is unusable.
The Loopless Strap Tool Series uses a clamping buckle to attach a loopless
strap to the wrench body. When a loopless strap breaks at the strain point,
the majority of the strap is still usable. The operator simply removes the
broken section, installs the remaining strap, and continues working.

LOOPLESS-STRAP STRAP WRENCHES

TOOL STRAP SUGGESTED
STRAP
TIP WRENCH P/N STRAP P/N WIDTH GRIPPING
STYLE (COLOR)
LOOPED
DIAMETER
The strap is inserted into the buckle, folded
back over itself, and clamped in place with
A BT-BS-610SS BT-A-6010-BK 1/2" (Black) No .25" to 1.50"
a 7/32 inch set screw.
BT-BS-610BSS BT-A-6010B-BK* 1/2" (Blue) No .25" to 1.50"
BT-BS-610RSS BT-A-6010R-BK 1/2"″ (Red) No .25" to 1.50"
B BT-BS-609SS BT-A-6010-BK 1/2" (Black) No .50" to 2.50"
BT-BS-609BSS BT-A-6010B-BK* 1/2" (Blue) No .50" to 2.50"
BT-BS-609RSS BT-A-6010R-BK 1/2"″ (Red) No .50"″ to 2.50"″
C BT-BS-611SS BT-A-6175-BK 5/8" (Black) No 1.00"″ to 4.00"″
Loopless-Strap Loopless
BT-BS-611BSS* BT-A-6175B-BK* 5/8"″ (Blue) No 1.00"″ to 4.00"″
Strap Wrench Strap
C BT-BS-618SS BT-A-6185-BK 1" (Black) No 1.00"″ to 4.00"
BT-BS-618BSS* BT-A-6185B-BK* 1"″ (Blue) No 1.00"″ to 4.00"″

*The blue series straps are preferred for general connector/accessory use.

SEE TORQUE CONVERSION CHARTS ON PAGE 47 FOR USE OF STRAP

WRENCHES AND TORQUE MEASUREMENT TOOLS.
Looped Strap Looped
Strap Wrench Strap

STANDARD DMC STRAP WRENCHES CAN BE CONVERTED TO "LOOPLESS".

All strap wrenches can be ordered as Loopless versions. However, if you already own DMC strap tools, we offer a
Retro Fit Kit to convert your existing looped strap tools to Loopless Strap Tools

RETROFIT KITS to convert looped strap tools to loopless strap tools. RETROFIT KIT COMPONENTS
Suggested
Strap Width Strap
Retrofit Kit P/N for Tool P/N Gripping
(color) Looped
Diameter

BT-BS-609SS-RK BT-BS-609 1/2" (Black) No .50" to 2.50"

BT-BS-609BSS-RK BT-BS-609B 1/2" (Blue) No .50" to 2.50"

BT-BS-610SS-RK BT-BS-610 1/2" (Black) No .25" to 1.50"

BT-BS-610BSS-RK BT-BS-610B 1/2" (Blue) No .25" to 1.50"
BT-BS-611SS-RK BT-BS-611 5/8" (Black) No 1.00" to 4.00"

BT-BS-618SS-RK BT-BS-618 1" (Black) No 1.00" to 4.00"

PAGE 44 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
HANDLE-LESS STRAP WRENCH

HANDLE-LESS STRAP WRENCHES

FOR TORQUE WRENCHES
TOOL STRAP SUGGESTED
STRAP
TIP WRENCH P/N STRAP P/N WIDTH GRIPPING
LOOPED
STYLE (COLOR) DIAMETER

HANDLE-LESS LOOPED STRAP WRENCHES

BT-BS-610T BT-A-6010 1/2"″ (Black) Yes .25"″ to 1.50"″

BT-BS-610BT* BT-A-6010B* 1/2"″ (Blue) Yes .25"″ to 1.50"″

A
BT-BS-610WT BT-A-6010W 1/2"″ (White) Yes .25"″ to 1.50"″

BT-BS-610RT BT-A-6010R 1/2"″ (Red) Yes .25"″ to 1.50"″

BT-BS-609T BT-A-6010 1/2"″ (Black) Yes .50"″ to 2.50"″

BT-BS-609BT* BT-A-6010B* 1/2"″ (Blue) Yes .50"″ to 2.50"″

B
BT-BS-609WT BT-A-6010W 1/2"″ (White) Yes .50"″ to 2.50"

BT-BS-609RT BT-A-6010R 1/2"″ (Red) Yes .50"″ to 2.50"″

The BT-BS-611T is shown here.
BT-BS-611T BT-A-6175 5/8"″ (Black) Yes 1.00"″ to 4.00"

HANDLE-LESS C BT-BS-611BT* BT-A-6175B* 5/8"″ (Blue) Yes 1.00"″ to 4.00"″

STRAP WRENCHES BT-BS-611WT BT-A-6175W 5/8"″ (White) Yes 1.00"″ to 4.00"″
DMC’s handle-less strap wrench
line has been specifically designed for BT-BS-618T BT-A-6185 1"″ (Black) Yes 1.00"″ to 4.00"″
torque-accurate connector assembly.
Based on DMC’s established line of C BT-BS-618BT* BT-A-6185B* 1"″ (Blue) Yes 1.00"″ to 4.00"″
torque wrenches, the handle-less strap BT-BS-618WT BT-A-6185W 1"″ (White) Yes 1.00"″ to 4.00"″
wrench attaches to the BT-ST-302D/
BT-ST-302DR Digital Torque Tool HANDLE-LESS LOOPLESS STRAP WRENCHES
and provides accurate torque without the
BT-BS-610SST BT-A-6010-BK 1/2" (Black) No .25" to 1.50"
interference of the strap wrench handle.
A BT-BS-610BSST BT-A-6010B-BK* 1/2" (Blue) No .25" to 1.50"

BT-BS-610RSST BT-A-6010R-BK 1/2"″ (Red) No .25"″ to 1.50"″

SEE TORQUE CONVERSION
BT-BS-609SST BT-A-6010-BK 1/2" (Black) No .50" to 2.50"
CHARTS ON PAGE 47 FOR USE OF
STRAP WRENCHES AND TORQUE B BT-BS-609BSST BT-A-6010B-BK* 1/2" (Blue) No .50" to 2.50"
MEASUREMENT TOOLS.
BT-BS-609RSST BT-A-6010R-BK 1/2"″ (Red) No .50"″ to 2.50"″

BT-BS-611SST BT-A-6175-BK 5/8" (Black) No 1.00"″ to 4.00"″

C
BT-BS-611BSST* BT-A-6175B-BK* 5/8"″ (Blue) No 1.00"″ to 4.00"″

BT-BS-618SST BT-A-6185-BK 1" (Black) No 1.00"″ to 4.00"

C
BT-BS-618BSST* BT-A-6185B-BK* 1"″ (Blue) No 1.00"″ to 4.00"″
*The blue series strap wrench and replacement straps are preferred for connector/accessory use.

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 45
TORQUE CONVERSION GENERAL INFORMATION

Torque is a standard term that is comprised of

“distance and force”. Since the force is applied
to a threaded component in a circular motion,
the distance applies to the radius (center of the
torque wrench drive to a designated point on
the torque wrench handle). In the case of wire
harness applications, it is usually expressed
in INCH-POUNDS, NEWTON-METERS, or
KILOGRAM-CENTIMETERS. When extensions
such as a crowfoot, or strap wrench is added
to a torque wrench, it changes the distance
(radius), so a mathematical formula is used to
determine the correct torque readings on the
torque wrench to compensate for the added
length. We have included the following formulas
for your convenience. See AIR 6151 (SAE) for
more information torque for connector/backshell
assembly.

When an adapter or extension is used on a torque wrench

it increases the torque range of the wrench. The formula
for computing torque when using an adapter or extension
is explained below.
Should it be necessary, due to obstructions, to have an angle
A = (Length) Distance from center of torque wrench between the two axes, then the above formula is modified as
square drive to center of the puller’s hand grip. follows. Due to increasing rounding errors, keep the angle as
B = Distance from center of torque wrench square small as possible.
drive to center of drive at end of extension.
C = (Torque) Torque wrench setting. A, B, C, D, & P are the same as above.
D = Torque desired at drive on end of extension.
P = (Force) Pull applied. E = Effective moment arm of the extension.
To determine torque wrench setting:
C = (D*A) / (A+B) Ø = Angle between extension axis and torque wrench axis.

NOTE: After computing “C” and setting wrench E = (B)(COS Ø)

to computation, measure and mark “A” where
pull is applied. Therefore:
It is recommended that the axis of the extension C = (D*A) / (A+(B*COS Ø))
always be used in line with axis of the torque wrench
as shown above. When Ø = 0, COS Ø = 1, then equation is reduced to
C = (D*A) / (A+B)

When Ø = 90°, COS Ø = 0 then C = D

(Regardless of the length B)
(Ref AIR 6151) `

PAGE 46 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 TORQUE CONVERSION CHARTS
TORQUE CONVERSION CHART
These torque conversion charts were calculated for the FOR BT-BS-609 SERIES USED WITH BT-ST-302D
BT-ST-302D/BT-ST-302DR Digital Torque Tool. If any
Diameter of DESIRED TORQUE VALUE (in-lbs)
other torque tool or instrument is used, calculate the torque Part Being
conversion by using the mathematical formula on page 46. Tightened 40 60 80 100 120 140 160 180 200
See page 63 for torque recommendations (Ref AIR6151).
0.50" 35 53 70 88 106 123 141 158 176

TORQUE CONVERSION CHART 0.75" 35 52 70 87 105 122 139 157 174

FOR BT-BS-611 AND BT-BS-618 SERIES 1.00" 34 52 69 86 103 121 138 155 172
USED WITH BT-ST-302D
1.50" 34 51 67 84 101 118 135 152 169
Diameter of DESIRED TORQUE VALUE (in-lbs)
Part Being 1.75" 33 50 67 83 100 117 134 150 167
Tightened 40 60 80 100 120 140 160 180 200 2.00" 33 50 66 83 99 116 132 149 165
1.00" 33 50 67 83 100 117 134 150 167
2.25" 33 49 65 82 98 115 131 147 164
1.50" 33 50 66 83 99 116 132 149 165
2.50" 32 49 65 81 97 113 130 146 162
1.75" 33 49 65 82 98 114 131 147 163 TORQUE READING ON INSTRUMENT (“C”)
2.00" 32 48 64 80 96 112 128 144 160
2.25" 32 48 63 79 95 111 127 143 158 TORQUE CONVERSION CHART
FOR BT-BS-610 SERIES USED WITH BT-ST-302D
2.50" 31 47 63 78 94 110 126 141 157
Diameter of DESIRED TORQUE VALUE (in-lbs)
2.75" 31 47 62 78 93 109 124 140 155 Part Being
Tightened 40 60 80 100 120 140 160 180 200
3.00" 31 46 62 77 92 108 123 138 154
0.25" 36 54 72 89 107 125 143 161 179
3.25" 30 46 61 76 91 107 122 137 152
0.50" 35 52 70 87 104 122 139 156 174
3.50" 30 45 60 75 90 106 121 136 151
0.75" 34 51 68 86 103 120 137 154 171
3.75" 30 45 60 75 90 105 119 134 149
1.00" 34 51 67 84 101 118 135 152 169
4.00" 30 44 59 74 89 104 118 133 148
1.50" 33 49 65 81 98 114 130 146 163
TORQUE READING ON INSTRUMENT (“C”)
1.75" 34 51 68 84 101 118 135 152 169
2.00" 33 50 67 83 100 117 133 150 166
2.25" 33 49 66 82 99 115 132 148 165
2.50" 32 49 65 81 97 113 130 146 162
TORQUE READING ON INSTRUMENT (“C”)

GENERAL PURPOSE BACKSHELL/ACCESSORY TOOLS

TOOL IDENTIFICATION CHART
F
A BT-HT-110 1/4 " Socket Drive Handle A
C

BT-HT-210 1/4 " Stationary Drive

Mounting Arm
B
BT-HT-211 3/8 " Stationary Drive
Mounting Arm
B
BT-D-0551 3/8 " to 1/4″ Adapter
C
BT-D-0622 1/4 " to 3/8″ Adapter
D E G
3/8 " Square Drive
D BT-HT-107 T-Handle Wrench
1/4 " Square Drive
E BT-HT-100 T-Handle Wrench
F BT-A-0513 Ratchet 3/8 " Drive
G M-7LB Illuminated Magnifier
© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 47
JAM NUT SOCKET TOOLS

COMPOSITE JAM NUT

SOCKETS
A unique process was developed
to mold this composite material which
contains a higher percentage of
fiberglass than is customarily used in
conventional molding technology. This
makes them as light and as strong as A B C
possible. The material will not scratch
The correct application of torque plating, or damage the finish on
is essential to most connector cabinets, panels, or bulkheads when A COMPOSITE (NON-MARKING)
applications where Jam Nut receptacle used properly.
connectors are used. The sealing B STEEL
ALUMINUM JAM NUT SOCKETS
components (usually an “O” ring)
must be compressed, but not to the When a metal socket is required, C ALUMINUM
point of damage. Another important the anodized aluminum series jam nut
consideration when tightening Jam sockets are a good choice. They are specific Jam Nut applications. Jam
Nuts is the thread strength, especially machined to the same configuration as nut durability test report available upon
in the various types of aluminum and the composite jam nut sockets with the request - contact DMC customer
composite connectors. square hole drive for torquing. service.
DMC’s Jam Nut Socket tools have STEEL JAM NUT SOCKETS
been developed specifically for the A steel series of jam nut sockets is
installation of Jam Nut receptacle also available, which some users prefer
connectors. They are available in a for firewall or other applications where
light weight composite construction, higher torque values are required.
anodized machined aluminum, and The traditional “General Purpose”
durable steel series. formed stainless steel sockets
(on page 50) are great for non-torque

Jam Nut Sockets are ideal for

torquing jam nuts on panels where
several connectors are crowded
together and in other tight spaces.

PAGE 48 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 COMPOSITE OR METAL JAM NUT SOCKETS PART NUMBER BT-J -XXX XX
OUTSIDE
DMC PART FITS JAM NUT FITS JAM NUT SIZE: SQUARE BASIC P/N
DIAMETER
NUMBER SIZE: INCHES MILLIMETERS DRIVE SIZE DESIGNATOR (SEE CHART)
REFERENCE
BT-J-117 .608" to .628" 15.41 mm to 15.95 mm 1/4" .914" MATERIAL:
BLANK = COMPOSITE; AL = ALUMINUM; S = STEEL
BT-J-118* .628" to .649" 15.95 to 16.48 1/4" .955"
BT-J-120 .671" to .693" 17.04 to 17.60 1/4" .010"
BT-J-121 .693" to .717" 17.60 to 18.21 1/4" 1.04"
BT-J-122* .717" to .741" 18.21 to 18.82 1/4" 1.07"
TO FIND THE CORRECT JAM NUT
SOCKET FOR YOUR APPLICATION,
BT-J-123 .741" to .765" 18.82 to 19.43 1/4" 1.10" MEASURE ACROSS THE FLATS OF
BT-J-124 .765" to .791" 19.43 to 20.09 1/4" 1.13" THE JAM NUT YOU ARE WORKING
BT-J-125 .791" to .818" 20.09 to 20.77 1/4" 1.16" WITH. NEXT, FIND THE SIZE RANGE
BT-J-126 .818" to .845" 20.77 to 21.46 1/4" 1.19" IN THE ADJACENT TABLE. LISTED
BESIDE IT WILL BE THE SOCKET
BT-J-127 .845" to .873" 21.46 to 22.17 1/4" 1.22" YOU NEED.
BT-J-128 .873" to .902" 22.17 to 22.91 1/4" 1.26"
BT-J-129 .902" to .933" 22.91 to 23.69 1/4" 1.29"
BT-J-130 .933" to .964" 23.69 to 24.48 3/8" 1.33"
BT-J-131 .964" to .996" 24.48 to 25.29 3/8" 1.36"
BT-J-132 .996" to 1.030" 25.29 to 26.16 3/8" 1.41"
BT-J-133 1.030" to 1.064" 26.16 to 27.02 3/8" 1.45"
BT-J-134 1.064" to 1.100" 27.02 to 27.94 3/8" 1.51"
BT-J-135 1.100" to 1.137" 27.94 to 28.87 3/8" 1.55"
BT-J-136 1.137" to 1.175" 28.87 to 29.84 3/8" 1.59"
BT-J-137 1.175" to 1.214" 29.84 to 30.83 3/8" 1.63"
BT-J-138 1.214" to 1.255" 30.83 to 31.87 3/8" 1.69"
BT-J-139 1.255" to 1.297" 31.87 to 32.94 3/8" 1.73"
BT-J-140 1.297" to 1.340" 32.94 to 34.03 3/8" 1.78"
BT-J-141 1.340" to 1.385" 34.03 to 35.17 3/8" 1.84"
BT-J-142 1.385" to 1.432" 35.17 to 36.37 3/8" 1.89"
BT-J-143 1.432" to 1.480" 36.37 to 37.59 3/8" 1.95"
BT-J-144 1.480" to 1.529" 37.59 to 38.83 3/8" 2.00"
BT-J-145 1.529" to 1.580" 38.83 to 40.13 3/8" 2.06"
BT-J-146 1.580" to 1.633" 40.13 to 41.47 3/8" 2.12"
BT-J-147 1.633" to 1.688" 41.47 to 42.87 3/8" 2.19"
BT-J-148 1.688" to 1.745" 42.87 to 44.32 3/8" 2.25"
BT-J-149 1.745" to 1.803" 44.32 to 45.79 3/8" 2.32"
BT-J-150 1.803" to 1.864" 45.79 to 47.34 3/8" 2.39"
BT-J-151 1.864" to 1.926" 47.34 to 48.92 3/8" 2.46"
BT-J-152 1.926" to 1.991" 48.92 to 50.57 3/8" 2.54"
BT-J-153 1.991" to 2.057" 50.57 to 52.24 3/8" 2.61"
BT-J-154 2.057" to 2.126" 52.24 to 54.00 3/8" 2.69"
BT-J-155 2.126" to 2.197" 54.00 to 55.80 3/8" 2.78"
BT-J-156 2.197" to 2.271" 55.80 to 57.68 3/8" 2.87"
BT-J-157 2.271" to 2.347" 57.68 to 59.61 3/8" 2.95"
BT-J-158 2.347" to 2.426" 59.61 to 61.62 3/8" 3.04"
BT-J-159 2.426" to 2.507" 61.62 to 63.67 3/8" 3.14"
BT-J-160* 2.507" to 2.591" 63.67 to 65.81 3/8" 3.24"
BT-J-161 2.591" to 2.678" 65.81 to 68.02 3/8" 3.34"
BT-J-162 2.678" to 2.769" 68.02 to 70.33 3/8" 3.44"
BT-J-163 2.769" to 2.860" 70.33 to 72.64 3/8" 3.54"
We also recommend that you
BT-J-164 2.860" to 2.956" 72.64 to 75.08 3/8" 3.66"
consider DMC's Safe-T-Cable® to
BT-J-165 2.956" to 3.055" 75.08 to 77.59 3/8" 3.77" secure Jam Nut receptacles where
BT-J-166 3.055" to 3.157" 77.59 to 80.18 3/8" 3.89" lockwire holes are provided.
BT-J-170* 3.457" to 3.557" 87.81 to 90.35 3/8" 4.38" The Low Profile Ferrule (shown
*Not available in composite material. here) lends itself to an efficient security
system for jam nut receptacles.

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 49
GENERAL PURPOSE JAM NUT SOCKETS

GENERAL PURPOSE JAM NUT SOCKETS

GENERAL PURPOSE JAM NUT SOCKETS
Formed Stainless Steel Jam Nut sockets are great AMPHENOL HEX REF.
DMC FITS JAM NUT EQUIVALENT
for non-torque specific jam nut applications. They are PART# SIZE: INCHES
BCO PART DIM:
COMPOSITE
NUMBER INCHES
plated for corrosion resistance, and have drive holes
to accommodate a metal rod drive tool (P/N DW75). CS8 .755 to .763 11-6266-3 3/4" BT-J-123
CS10 .880 to .888 11-6266-5 7/8" BT-J-128
CS12 1.068 to 1.077 11-6266-8 1 1/16" BT-J-134
CS14 1.194 to 1.204 11-6266-10 1 3/16" BT-J-137
CS16 1.320 to 1.331 11-6266-12 1 5/16" BT-J-140
CS18 1.446 to 1.457 11-6266-14 1 7/16" BT-J-143
CS20 1.571 to 1.580 11-6266-16 1 9/16" BT-J-145
CS22 1.696 to 1.708 11-6266-18 1 11/16" BT-J-148
CS24 1.822 to 1.835 11-6266-20 1 13/16" BT-J-150
CS22-1 2.011 to 2.025 11-6266-23 2"″ BT-J-153
CS24-1 2.137 to 2.151 11-6266-25 2 1/8"″ BT-J-155
BT-J-161 &
CS32 2.640 to 2.687 11-6266-33 2 5/8"
BT-J-162

DMC1554 SET INCLUDES ALL 12 SOCKETS LISTED ABOVE AND DW75 DRIVE ROD

JR700

ADJUSTABLE TORQUE CONVERSION CHART

JAM NUT WRENCH FOR JR700 TOOL USED WITH BT-ST-302D/BT-ST-302DR
The JR700 adjustable jam
Diameter of
nut wrench is a versatile tool for Part Being DESIRED TORQUE VALUE (in-lbs) (“D”)
maintenance and low volume Tightened
production. The rugged all steel 40 60 80 100 120 140 160 180 200
construction makes this tool a good
0.50" 25 38 51 64 76 89 102 115 127
choice for heavy duty applications.
0.75" 26 39 51 64 77 90 103 116 128
The tool may be adjusted to
accommodate hex nuts from .75 inch 1.00" 26 39 52 65 78 91 104 117 129
to 3.25 inch (across flat) dimensions. 1.50" 26 40 53 66 79 92 106 119 132
The maximum working depth is 1.0 1.75" 27 40 53 67 80 93 107 120 133
inch. This range accommodates most
2.00" 27 40 54 67 81 94 108 121 135
common connectors.
A standard 3/8 inch drive torque 2.25" 27 41 54 68 82 95 109 122 136
tool may be used in conjunction 2.50" 27 41 55 69 82 96 110 124 137
with this tool to limit the possibility 2.75" 28 42 55 69 83 97 111 125 139
of overtightening. If torque values 3.00" 28 42 56 70 84 98 112 126 140
require close tolerance accuracy,
3.25" 28 42 57 71 85 99 113 127 141
direct reading sockets (page 34)
are recommended. TORQUE READING ON INSTRUMENT (“C”)

SEE TORQUE CONVERSION CHARTS ON PAGE 47 FOR USE OF STRAP

WRENCHES AND TORQUE MEASUREMENT TOOLS.
PAGE 50 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
CIRCULAR RING PLIERS
CIRCULAR RING PLIERS

CIRCULAR RING PLIERS

The DRPXX circular ring pliers are
specifically designed to grip circular
connector and backshell components
which would be deformed by other
gripping methods. The non marring
­rubber jaw lining material is available in
strip form and may be used to replace
worn jaw inserts. It is held in place by
interlocking fingers which are molded into
the material.
The following chart defines the working
Durable hinge allows tool to open 180°. Pads are easily replaceable.
diameters and the tools which are
available in this series.
TOOL PART GRIP RANGE*
Replacement Pads for Circular Ring
NUMBER INCH METRIC (mm) Pliers are available (P/N DRP-RS-1). This
DRP7, DRP7N** 0.50 to 0.53 12.70 to 13.46 replacement pad is supplied as a 4.25"
DRP8, DRP8N** 0.56 to 0.59 14.22 to 14.98 strip that must be cut to length needed.
DRP9, DRP9N** 0.62 to 0.65 15.74 to 16.51
Mini Soft-Jaw Pliers
DRP10, DRP10N** 0.67 to 0.70 17.01 to 17.78 with angled head
BT-SJ-509A
DRP11, DRP11N** 0.74 to 0.77 18.79 to 19.55
DRP12, DRP12N* 0.80 to 0.83 20.32 to 21.08 Mini Soft-Jaw Pliers
with straight head
DRP13, DRP13N** 0.85 to 0.88 21.59 to 22.35 BT-SJ-509R
DRP14, DRP14N** 0.89 to 0.92 22.60 to 23.36
DRP15, DRP15N** 0.97 to 1.00 24.63 to 25.40
DRP16, DRP16N** 1.05 to 1.08 26.67 to 27.43
DRP17, DRP17N** 1.08 to 1.11 27.43 to 28.19
DRP18, DRP18N** 1.11 to 1.14 28.19 to 28.95 Soft-Jaw Pliers
BT-SJ-468
DRP19, DRP19N** 1.20 to 1.23 30.48 to 31.24
DRP20, DRP20N** 1.27 to 1.30 32.25 to 33.02
SOFT JAW ADJUSTABLE PLIERS
DRP21, DRP21N** 1.33 to 1.36 33.78 to 34.54
The BT-SJ-468 soft jaw adjustable
DRP22, DRP22N** 1.39 to 1.42 35.30 to 36.06 pliers are a handy addition to general
DRP23, DRP23N** 1.45 to 1.48 36.83 to 37.59 maintenance tool stations. This tool can
DRP24, DRP24N** 1.49 to 1.52 37.84 to 38.60 provide a reliable gripping function for
DRP25, DRP25N** 1.57 to 1.60 39.87 to 40.64
assembly, disassembly, and positioning
of circular and oval parts.
DRP26, DRP26N** 1.61 to 1.64 40.89 to 41.65
The Mini Soft-Jaw Pliers are available
DRP27, DRP27N** 1.76 to 1.79 44.70 to 45.46 in both straight (BT-SJ-509R) and 30°
DRP28, DRP28N** 1.89 to 1.92 48.00 to 48.76 angled head (BT-SJ-509A) versions.
DMC1924 Set of 15 DRP Series Pliers and 10 Replacement Pads Replacement jaw inserts are available
DRP-RS-1 Replacement Pad for all DRP Series Pliers
for all soft jaw pliers, contact DMC for
part numbers.
*On a smooth surface. Knurled surfaces slightly below this range are compatible with these tools.
**These port numbers indicate pliers sizes with a more narrow head.
© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 51
EMI/RFI SHIELD BAND APPLICATION TOOLS

Introduction:
Welded Buckle Type
The Aerospace Industry has standardized on two distinct Band Styles for Ter-
mination of EMI/RFI Shielding on wiring systems. DMC is the only QPL Suppli-
er with complete coverage of all M85049/128 Accessory Bands. This page and
the following page is a summary of our Shield Band Installation Tooling. More
complete and detailed Product Information is available. Contact DMC and ask
Stamped Buckle Type for the M85049/128 EMI/RFI Shield Band Tooling Guide.

The two Configurations are commonly referred to as the “Stamped Buckle”

Stamped Buckle Type Bands and the “Welded Buckle” Bands. Each configuration is terminated with a
different complement of tooling. The following table is a quick reference guide
to the Shield Band Part Numbers, and the Tooling Type which is designated for
each.
Quick Reference Band Part Number Installation to Tool Table
MIL P/N DMC P/N USED WITH MIL P/N DMC P/N USED WITH
M85049/128-1 DBS-128-1 2 STEP TOOL M85049/128-5 DBS-128-5 2 STEP TOOL
Welded Buckle Type
M85049/128-2 DBS-128-2 2 STEP TOOL M85049/128-6 DBS-128-6 2 STEP TOOL

M85049/128-3 DBS-128-3 1 STEP TOOL M85049/128-7 DBS-128-7 1 STEP TOOL

M85049/128-4 DBS-128-4 1 STEP TOOL M85049/128-8 DBS-128-8 1 STEP TOOL

One Step Banding Tools System

ONE-STEP BAND APPLICATION TOOLS
DBS-2100 & DBS-2200 (M81306/1-A & M81306/1-B)
The One-Step Band Application Tools are built to M81306/1 and designed to install M85049/128-3,
M85049/128-4, M85049/128-7, and M85049/128-8 “stamped buckle” bands. These tools are constructed
to survive the demands of production and maintenance use, and
remain precisely adjusted to provide a quality band termination.
The tension-lock system gives the operator a positive indication when the
preset tension is reached.

DBS-2200 .125 Wide Mini-Band Application Tool M81306/1-B:

• Size and Weight: 6.71” x 6.75” x .92”, 1.02 lbs.
• Tension Range: 75–85 lbs.
• Cut-off blades replaceable with Blade Replacement Kit: DBS-2100-BRK

DBS-2100 .250 Wide Band Application Tool M81306/1-A:

• Size and Weight: 6.71” x 6.75” x .92”, 1.02 lbs.
• Tension Range: 145–155 lbs.
• Cut-off blades replaceable with Blade Replacement Kit: DBS-2100-BRK

Field Inspection Gages are available to check the tension of the DMC
One-Step Banding Tools. The .250 width band tool (DBS-2100 Series)
requires the DBS-CG7 (M81306/1C) gage and the .125 width band tool
(DBS-2200) requires the DBS-CG8 (M81306/1D) gage. Other verifica-
tion devices are available. Consult DMC for details.
PAGE 52 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 MILITARY PART NUMBER TO DMC PART NUMBER CHART
TOOL MIL P/N DESCRIPTION WIDTH DMC P/N APPLICATION
M81306/1-01 Set: One-Step Tool, Gage, and Tension Key .250 DBS-2102 M85049/128-3 & -4
M81306/1-02 Set: One-Step Tool, Gage, and Tension Key .125 DBS-2202 M85049/128-7 & -8
M81306/1A One-Step Band Installation Tool .250 DBS-2100 M85049/128-3 & -4
M81306/1B One-Step Band Installation Tool .125 DBS-2200 M85049/128-7 & -8
M81306/1C Tension Verification Compression Fixture .250 DBS-CG7 DBS-2100
M81306/1D Tension Verification Compression Fixture .125 DBS-CG8 DBS-2200
M81306/1E Tension Adjustment Key .125 & .250 DBS-2100-32 DBS-2100 & DBS-2200
M81306/2-01 Two-Step Installation Tool and Roll-Over Tool .250 DBS-1101 M85049/128-1 & -2
M81306/2-02 Two-Step Installation Tool and Roll-Over Tool .125 DBS-1201 M85049/128-5 & -6
M81306/2-01A Two-Step Band Tool .250 DBS-1100 M85049/128-1 & -2
M81306/2-02B Two-Step Band Tool .125 DBS-1200 M85049/128-5 & -6
M81306/2-01C Roll Over Tool .250 DBS-RO3 M85049/128-1 & -2
M81306/2-02D Roll Over Tool .125 DBS-RO5 M85049/128-5 & -6
M81306/2-01E Tension Verification Gage & Compression Fixture .250 DBS-CG2A DBS-1100
M81306/2-02F Tension Verification Gage & Compression Fixture .125 DBS-CG3A DBS-1200

Two-Step Banding Tools System

DBS-1100 (M81306/2-01A)
or
DBS-1200 (M81306/2-02B)

The DMC verification System

is easily accomplished with
a simple compression fixture
and a GO-NO/GO Gage. See
table above for part numbers
and Application for the DBS-
PBT1100 CG verification Gage and
Compression Fixtures. Other
Uses compressed air to install the
verification devices are avail-
same M85049/128-X Bands as the
Corresponding Manual Tool DBS-RO3 able, consult DMC for details.

DBS-1100 AND DBS-1200 PBT1100 & PMBT1200

HAND OPERATED BANDING TOOLS PNEUMATIC BAND APPLICATION TOOLS
TWO STEP BAND APPLICATION TOOLS The PBT1100 & PMBT1200 series Pneumatic Band
Application Tools are lightweight, dependable, and easy to
DBS-1100 (M81306/2-01A) .250 Wide Band Tool:
operate. Many of the components are interchangeable with the
corresponding hand tool. DMC’s Pneumatic Two-Step Banding
• Size and Weight: 1.38” x 5.5” x 7.5”, 1.4 lbs.
Tools are compatible with all currently available welded bands
• Tension Range: 140–160 lbs.
to M85049/128.
• Cut-off blade: replaceable with DBS-1100-7
PBT1100 .250 Wide Band Application Tool
DBS-1200 (M81306/2-02B) .125 Wide Mini-Band Tool:
• Size and Weight: 1.38” x 5.5” x 7.5”, 1.4 lbs. • Size and Weight: 8.75” L, 1.52 lbs.
• Tension Range: 70-90 lbs. • Calibration Range: 140–160 lbs.
• Cut-off blade: replaceable with DBS-1100-7
PMBT1200 .125 Wide Mini-Band Application Tool
• Size and Weight: 8.75” L x 1.52 lbs.
• Calibration Range: 70-90 lbs.

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 53
DMC SHIELD BAND INSTALLATION KITS

The DMC2058A One-Step Band Installation Kit

The DMC2058A is an all inclusive One-step Band Installation Kit. It

provides your service technicians with both the DBS-2100 (M81306/1A)
.250” Wide Band Application Tool and the DBS-2200 (M81306/1B) .125”
Wide Mini-Band Application Tool, along with stamped buckle bands,
and all accessories needed to terminate bands.
Also included are all calibration, support accessories, and illustrated
operating instructions for all the tooling
DMC2058A Contents included.
DBS-2102 (M81306/1-01) The DMC2058A Kit is equipped to
install all M85049/128-3,-4 (.250 Wide)
DBS-2202 (M81306/1-02)
and M85049/128-7, -8 (.125 Wide) DMC2058A One-Step
M85049/128-3 (10 PCS) stamped EMI/RFI shield bands. Banding Tool Kit
M85049/128-7 (10 PCS)

The DMC Two-Step Band Installation Kit

If your process calls for the welded buckle shield bands,

the Two- Step Band Installation Kit will provide all tools and
accessories to support the assembly or maintenance of your
wiring system.
Also included are all calibration, support accessories, and
illustrated operating instructions for all the tooling included.
The DMC60A Kit is equipped to install all M85049/128-1, -2
(.250 Wide) welded EMI/RFI shield bands. The DMC 1379 similar
to the DMC60A, but without cutters and shielding (includes all
two step tools for .250 wide welded buckle bands).
Tool Kit is supplied in 1 fiberglass case and includes : Name
Plate, Foam Pads/Inserts, Contents and Instruction Sheets.
DMC60A Two-Step Other installation kits available with different capabilities.
Banding Tool Kit Contact DMC for details.

DMC60A Contents
Quantity Part # Description
1 DBS-1100 (M81306/2-01A) Hand Operated Band Application Tool - 1/4”
1 DBS-BR1 Band Removal Tool
1 DBS-RO3 (M81306/2-01C) Roll-Over Tool for .250 Band Tab
1 DBS-GG2 Field Calibration Fixture for DBS-1100
1 G691 Go/No-Go Gage for DBS-CG2 Fixture
100 M85049/128-2 .250 wide x 14.0" long EMI/RFI Band (coiled)*
1 MISC. Tape, Braided Shielding, & Split Rings, & Hex Wrenches, Shears, Spare Cutter blades

PAGE 54 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
EMI/RFI BAND APPLICATION SYSTEM
FOR .125 & .250 SHIELD TERMINATION BANDS
Careful measurement should be made prior to installing Apply an adequate amount of pressure in line with the
the backshell. The outer jacket is then uniformly removed cable as it enters the
at a distance which would backshell to allow the
allow the braid to make a 1/8 inch space to be
comfortable transition onto reduced to zero. The
the backshell termination tool is then activated
area. This dimension will to the preset tension.
vary depending upon the The band is then bent
differences between cable sharply at the buckle
and backshell diameters or other application dependent approximately 90° then cut-off using the cut-off lever on
factors. the tool (applies to two-step only). If the band is uncurled
The braid is then trimmed to a length which will allow for any reason, it must be double looped through the
it to extend 1 inch past the backshell termination platform. buckle before termination.
Then the braid is carefully The 90° tab is then curled and folded back over the
folded rearward to expose the buckle using the rollover tool (applies to two-step only).
wires which will be inside the For braiding a non-jacket cable use fine point shears
backshell. to trim the excess braid as
A sufficient number of wraps close to the connector side
of self-vulcanizing tape (nor- of the bands as possible. Do
mally red in color) are applied over the wires to build up a not leave any unsecured braid
diameter slightly less than the inside diameter of the back- wires longer than 1/8 inch. Do
shell. Care should be taken not to apply tension to the not allow the trimmed wires to
contacts located in the outer perimeter of the connector. fall in any areas where they
These layers of tape are followed by a minimum of one may present a foreign object
layer of Teflon tape which damage hazard.
will prevent adhesion with PROCEDURE FOR SPLICING
the backshell and other
components. The jacket is present, and
shield has been cut and sep-
The backshell is then arated to expose the wires
installed onto the connec- requiring service. Care must
tor, using a nonabrasive tool such as a strap wrench. be taken to avoid damag-
The braid is then care- ing the insulation on internal
fully moved from under the wires. The required service is
backshell. It is important to then completed.
retain the woven charac-
teristics of the braid during The wire bundle is then
this step. protected by a few wraps of
self-vulcanizing tape followed
Use self-vulcanizing tape or a preformed component to by 2–3 layers of teflon tape.
build up the area behind the backshell. It is important that An appro­priate size split-
the braid is sup­ported in the transition from the backshell ring set is then selected and
rear diameter to the natural diameter of the wire bundle. installed. One layer of teflon
Leave approximately 1/8 inch tape is applied over the split
spacing between the tape ring set to hold the halves in position while the next steps
wrap and the backshell. are being performed.
The braid is pushed into The braid is then overlapped across the split ring set. Be
position over the backshell sure the braid ends protrude completely under the band in
­termination platform. Care both directions.
must be taken to make sure
the weave is uniform and no Heat-shrinkable tape is then
large “windows” are present. applied over the splice. When a
jacketed cable is used, be sure
A shield termination band is then loaded into the tool. The the tape extends onto the jacket in
band is then slid over the connector/backshell assembly both directions.
into a position of a
­ lignment with the t­er­mination platform.

*NOTE: 2 Step Tool shown. These instructions are general and apply to One Step and Two Step tools. If these instructions conflict with engineering processes, the latter shall apply.
© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 55
 BETA ADAPTOR KITS

Kit configuration may vary from example shown.

Configuration depends on application, user requirements,
and packaging needs of the customer.

PAGE 56 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 BETA ADAPTOR TOOL KITS
MORE THAN JUST A BOX OF TOOLS!

DMC’s Adaptor Tool Kits are

designed to keep your BETA tools
organized and provide all the necessary
information concerning the selection
and use of the tooling. A collection of
tools and accessories are packaged in a
well organized case or cabinet. And the
complete support data package makes
a DMC Kit more than just a box of tools.
DMC has designed and manufactured
system service kits longer than anyone
in the connector tooling industry. This
experience has enabled DMC the
capabilities to design a wiring system
service kit for virtually any electrical
interconnect system. DMC Kits have
proven their reliability and versatility
over years of dependable service to the
manufacturing and MRO industries.
We offer an extensive line of
maintenance/repair kits, production
(work station) kits, and tool sets,
many of which contain tools from
the BETA product line. For a listing
of wiring system maintenance tool
kits, or assistance with your individual
requirements, contact DMC.
Many BETA Backshell Tools are
available with other DMC products in
existing DMC Wiring System Service Kits
or in a different configuration than those
shown. Please consult DMC for your
specific requirements.

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • FAX 407-855-6884 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 57
AS85049 CONNECTOR ACCESSORIES
QUICK REFERENCE GUIDE

SPECIFICATION TITLE APPLICATION PAGE SPECIFICATION TITLE APPLICATION PAGE

Backshell, Environmental, AS50151 Solder AS50151 Crimp,
Cable Sealing, Straight, Type, V Thread of Backshell, Environmental, MIL-DTL-26482
AS85049/1 6
Grounding (Without Strain MS310X, Classes A, Cable Sealing, Straight, Series 2, AS81703
AS85049/10 9, 20
Relief), Category 1C B, C or K Connectors Shield Termination, Series 3, and MIL-
Category 1A DTL-83723 Series III
AS50151 Solder
Backshell, Environmental, Connectors
Type, V Thread of
AS85049/2 Cable Sealing, Straight, 6
MS310X, Classes A, AS50151 Crimp, MIL-
Category 1C DTL-26482 Series 2,
B, C or K Connectors Backshell, Environmental, Cable
AS85049/11 AS81703 Series 3, and 9, 20
MIL-DTL-22992 Sealing, Straight, Category 1A
MIL-DTL-83723 Series
Backshell, Cable Sealing,
AS85049/3 Connectors, Classes 7 III Connectors
Straight, Category 1A
C, J, and R Backshell, Straight, Non-Self-
MIL-DTL-38999 Series
Backshell, Cable Sealing, MIL-DTL-22992 AS85049/14 Locking and Self-Locking, 14, 15
III and IV Connectors
AS85049/4 Straight, Step-Up, Category Connectors, Classes 7 Category 3B
1A C, J, and R Strain Relief, 45°, Non-Self-
MIL-DTL-38999 Series
AS85049/15 Locking and Self-Locking, 14, 15
Backshell, Cable Sealing, MIL-DTL-22992 Category 4C
III and IV Connectors
AS85049/5 Straight, Step-Down, Connectors, Classes 7
Category 1A C, J, and R Strain Relief, 90°, Non-Self-
MIL-DTL-38999 Series
AS85049/16 Locking and Self-Locking, 14, 15
III and IV Connectors
AS50151 Crimp, Category 4C
MIL-DTL-26482 Backshell, Environmental,
Backshell, Environmental, MIL-DTL-38999 Series
Series 2, AS81703 AS85049/17 Straight, Shield Termination, 12, 13
AS85049/6 Cable Sealing, 45°, Shield 9, 20 I and II Connectors
Series 3, and MIL- Category 2B
Termination, Category 1A
DTL-83723 Series III
Backshell, Environmental, MIL-DTL-38999 Series
Connectors AS85049/18 14, 15
Straight, RFI/EMI, Category 2B III and IV Connectors

AS50151 Crimp, Backshell, Nonenvironmental, MIL-DTL-38999 Series

AS85049/19 14, 15
MIL-DTL-26482 Straight, RFI/EMI, Category 3B III and IV Connectors
Backshell, Environmental,
Series 2, AS81703 Backshell, Straight, RFI, EMI, MIL-DTL-38999 Series
AS85049/7 Cable Sealing, 45°, 9, 20 AS85049/20 14, 15
Series 3, and MIL- Category 3B III and IV Connectors
Category 1A
DTL-83723 Series III
Connectors Backshell, Nonenvironmental, MIL-DTL-38999 Series
AS85049/21 14, 15
Straight, Category 3B III and IV Connectors
AS50151 Crimp,
MIL-DTL-26482
Backshell, Environmental, AS50151 Crimp, MIL-
Series 2, AS81703
AS85049/8 Cable Sealing, 90°, Shield 9, 20 Backshell, Nonenvironmental, DTL-26482 Series 2,
Series 3, and MIL-
Termination, Category 1A AS85049/23 45°, Shield Termination, AS81703 Series 3, and 9, 20
DTL-83723 Series III
Category 3A MIL-DTL-83723 Series
Connectors III Connectors

AS50151 Crimp,
MIL-DTL-26482 AS50151 Crimp, MIL-
Backshell, Environmental,
Series 2, AS81703 Backshell, Nonenvironmental, DTL-26482 Series 2,
AS85049/9 Cable Sealing, 90°, 9, 20
Series 3, and MIL- AS85049/24 90°, Shield Termination, AS81703 Series 3, and 9, 20
Category 1A Category 3A MIL-DTL-83723 Series
DTL-83723 Series III
Connectors III Connectors

Right Angle Strain Relief Backshells

Tie Strap Backshell with Shield Sockets

Non-Environmental Right Straight

Right Angle Non-Environmental
Angle Strain Relief Backshells Environmental Backshell Strain Relief Backshell
DMC does NOT provide connectors, backshells, accessories, or wiring components. Parts shown here are for reference only.

PAGE 58 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 SPECIFICATION TITLE APPLICATION PAGE SPECIFICATION TITLE APPLICATION PAGE
AS50151 Crimp, MIL- Strain Relief, Straight, Self-
MIL-DTL-38999 Series
Backshell, Nonenvironmental, DTL-26482 Series 2, AS85049/38 Locking and Non-Self-Locking 14, 15
III and IV Connectors
AS85049/25 Straight, Shield Termination, AS81703 Series 3, and 9, 20 Category 4C
Category 3A MIL-DTL-83723 Series
Strain Relief, 90°, Self-Locking
III Connectors MIL-DTL-38999 Series
AS85049/39 and Non-Self-Locking Category 14, 15
III and IV Connectors
AS50151 Crimp, MIL- 4C
Backshell, Nonenvironmental, DTL-26482 Series 2,
AS50151 Solder Type,
AS85049/26 Straight, Shield Termination, AS81703 Series 3, and 9, 20
Nonenvironmental, Strain Relief, V Thread of MS310X,
Category 3A MIL-DTL-83723 Series AS85049/41 6
Straight, Category 4C Classes A, B, C or K
III Connectors
Connectors
Backshell, Nonenvironmental,
MIL-DTL-38999 Series AS50151 Solder Type,
AS85049/27 Straight, Self-Locking and Non- 12, 13
I and II Connectors Nonenvironmental, Strain Relief, V Thread of MS310X,
Self-Locking, Category 3B AS85049/42 6
Straight, Category 4A Classes A, B, C or K
Backshell, Nonenvironmental, Connectors
MIL-DTL-83733
AS85049/28 Straight, Shield Termination, N/A
Connectors AS50151 Crimp, MIL-
Category 3B
Strain Relief, Nonenvironmental, DTL-26482 Series 2,
Backshell, Nonenvironmental, MIL-DTL-38999 Series AS85049/43 Self-Locking and Non-Self- AS81703 Series 3, and 6, 9, 20
AS85049/29 12, 13
Straight, Category 3B I and II Connectors Locking, 45°, Category 4B MIL-DTL-83723 Series
III Connectors
Backshell, Nonenvironmental,
MIL-DTL-38999 Series
AS85049/30 Straight, Individual Shielded 12, 13
I and II Connectors
Wire Termination, Category 3B Strain Relief, Straight, Category MIL-DTL-83733
AS85049/44 N/A
4C Rectangular Connectors
AS50151 Crimp, MIL-
Backshell, Nonenvironmental, DTL-26482 Series 2,
AS85049/31 Straight, Self-Locking and Non- AS81703 Series 3, and 9, 20 MIL-DTL-27599 Series
Self-Locking, Category 3B MIL-DTL-83723 Series Strain Relief, Straight, I and MIL-DTL-38999
AS85049/45 12, 13
III Connectors Nonmetallic, Category 4C Series I and II
Connectors

Backshell, Nonenvironmental, MIL-DTL-27599 Series

MIL-DTL-38999 Series Strain Relief, 90°, Nonmetallic, I and MIL-DTL-38999
AS85049/32 90°, Shield Termination, 12, 13 AS85049/46 12, 13
I and II Connectors Category 4C Series I and II
Category 7
Connectors
Strain Relief, 90°, Self-Locking
Backshell, Nonenvironmental, MIL-DTL-38999 Series
MIL-DTL-38999 Series AS85049/47 and Nonself-Locking, Category 12, 13
AS85049/33 Straight, Shield Termination, 12, 13 I and II Connectors
I and II Connectors 4C
Category 7
Strain Relief, Straight, Category MIL-DTL-24308
MIL-DTL-26482 Series AS85049/48 N/A
7 Rectangular Connectors
I Jam Nut Receptacle
Backshell, Nonenvironmental, Connector (Inactive for Strain Relief, Straight, Self-
AS85049/34 9 MIL-DTL-38999 Series
Threaded Adapter, Category 7 New Design Equipment AS85049/49 Locking and Nonself-Locking, 12, 13
I and II Connectors
or Modification of Category 4C
Existing Equipment)
MIL-DTL-24308
AS85049/50 Strain Relief, 90°, Category 7 N/A
MIL-DTL-27599 Series Rectangular Connectors
Backshell, Nonenvironmental,
1 and MIL-DTL-38999
AS85049/36 Straight, EMI/RFI Shield 12, 14
Series I and II AS50151 Crimp, MIL-
Termination, Category 3B
Connectors Strain Relief, Nonenvironmental, DTL-26482 Series 2,
AS85049/51 90°, Self-Locking and Non- AS81703 Series 3, and 6, 9, 20
Backshell, Nonenvironmental,
MIL-DTL-38999 Series Self-Locking, Category 4B MIL-DTL-83723 Series
AS85049/37 Split 90°, EMI/RFI Shield 12, 13
I and II Connectors III Connectors
Termination, Category 3B

Straight Non-Environmental Straight Environmental Backshell

Strain Relief Backshells

Compression Ring
Extended Backshells

DMC does NOT provide connectors, backshells, accessories, or wiring components. Parts shown here are for reference only.

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 59
AS85049 CONNECTOR ACCESSORIES
QUICK REFERENCE GUIDE

SPECIFICATION TITLE APPLICATION PAGE SPECIFICATION TITLE APPLICATION PAGE

AS50151 Crimp, MIL- Strain Relief, Split 90°, MIL-DTL-38999 Series
AS85049/65 12, 13
Strain Relief, Nonenvironmental, DTL-26482 Series 2, Category 4C I and II Connectors
AS85049/52 Straight, Self-Locking and Non- AS81703 Series 3, and 6, 9, 20
Self-Locking, Category 4B MIL-DTL-83723 Series Adapter, Shrink Boot, Category MIL-DTL-38999 Series
III Connectors AS85049/69 14, 15
5 III and IV Connectors
AS50151 Crimp, MIL-
DTL-26482 Series 2, Use With AS85049/61
Strain Relief, Nonenvironmental, AS85049/74 Potting Boot, Category 7 N/A
AS85049/53 AS81703 Series 3, and 6, 9, 20 Potting Boot Ring
Straight, Category 4C
MIL-DTL-83723 Series Use With AS85049/58
III Connectors AS85049/75 Potting Boot, Category 7 N/A
Potting Boot Ring

AS50151 Crimp, MIL- Backshell, Environmental, 90°,

MIL-DTL-38999 Series
DTL-26482 Series 2, AS85049/76 Shield Termination, Category 12, 13
Strain Relief, Nonenvironmental, I and II Connectors
AS85049/54 AS81703 Series 3, and 6, 9, 20 2B, Nonself-Locking
45°, Category 4C
MIL-DTL-83723 Series Backshell, Environmental, 45°,
III Connectors MIL-DTL-38999 Series
AS85049/77 Shield Termination, Category 12, 13
I and II Connectors
2B, Nonself-Locking
AS50151 Crimp, MIL-
Strain Relief, Nonenvironmental, DTL-26482 Series 2, Backshell, Environmental, 45°,
MIL-DTL-38999 Series
AS85049/55 90°, Self-Locking and Non- AS81703 Series 3, and 6, 9, 20 AS85049/78 Shield Termination, Category 14, 15
III and IV Connectors
Self-Locking, Category 4C MIL-DTL-83723 Series 2B, Nonself-Locking
III Connectors Backshell, Environmental, 90°,
MIL-DTL-38999 Series
Strain Relief, Straight, Category MIL-DTL-38999 Series AS85049/79 Shield Termination, Category 14, 15
AS85049/56 12, 13 III and IV Connectors
4C I and II Connectors 2B, Nonself-Locking

Strain Relief, 45°, Self-Locking Dummy Contact, Sizes 12 and MIL-DTL-38999 12, 13,
MIL-DTL-38999 Series AS85049/80
AS85049/57 and Nonself-Locking, Category 12, 13 8, Category 7 Connectors 14, 15
I and II Connectors
4C MIL-DTL-38999 12, 13,
AS85049/81 Seal Plug, Size 10, Category 7
MIL-DTL-38999 Series Connectors 14, 15
AS85049/58 Ring, Potting Boot, Category 5 12, 13
I and II Connectors Backshell, Straight, Self- AS50151 Crimp, MIL-
MIL-DTL-22992 Locking, Non Self-Locking, DTL-26482 Series 2,
Adapter, Shrink Boot, Category AS85049/82 Shield Band Termination AS81703 Series 3, and 6, 9, 20
AS85049/59 Connectors, Classes C, 7
5 (RFI/EMI), Shrink Sleeve MIL-DTL-83723 Series
J, and R
Accommodation, Category 3B III Connectors
AS50151 Crimp,
MIL-C-26482 Series 2, Backshell, 45°, Self-Locking, AS50151 Crimp, MIL-
Adapter, Shrink Boot, Category Non Self-Locking, Shield DTL-26482 Series 2,
AS85049/60 AS81703 Series 3, and 6, 9, 20
5 AS85049/83 Band Termination, (RFI/EMI), AS81703 Series 3, and 6, 9, 20
MIL-DTL-83723 Series
III Connectors Shrink Sleeve Accommodation, MIL-DTL-83723 Series
Category 3B III Connectors
MIL-DTL-27599
AS85049/61 Ring, Potting Boot, Category 5 N/A
Connectors
Backshell, 90°, Self-Locking, AS50151 Crimp, MIL-
Adapter, Shrink Boot, Category MIL-DTL-38999 Series Non Self-Locking, Shield DTL-26482 Series 2,
AS85049/62 12, 13 AS85049/84 Band Termination, (RFI/EMI), AS81703 Series 3, and 6, 9, 20
5 I and II Connectors
Shrink Sleeve Accommodation, MIL-DTL-83723 Series
Category 3B III Connectors
Strain Relief, 90°, Self-Locking
MIL-DTL-38999 Series
AS85049/63 and Nonself-Locking, Category 12, 13
I and II Connectors Backshell, Straight, Self-
4C
Locking, Non Self-Locking,
MIL-DTL-38999 Series
AS85049/85 Shield Band Termination, 12, 13
Strain Relief, Split, Straight, MIL-DTL-38999 Series I and II Connectors
AS85049/64 12, 13 (RFI/EMI), Shrink Boot
Category 4C I and II Connectors Accommodation, Category 3B

Protective Cover and Lanyard Dummy Contacts

(Ref: AS85049/80)

Shorting Cap Backshell

DMC does NOT provide connectors, backshells, accessories, or wiring components. Parts shown here are for reference only.

PAGE 60 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
 SPECIFICATION TITLE APPLICATION PAGE SPECIFICATION TITLE APPLICATION PAGE
Backshell, 45°, Self-Locking, Mounting Device, Flange
Non Self-Locking, Shield AS85049/96 Type, 1/4 Mounting Perimeter, General Use N/A
MIL-DTL-38999 Series
AS85049/86 Band Termination, (RFI/EMI), 12, 13 Medium/Light Duty, Category 7
I and II Connectors
Shrink Sleeve Accommodation,
RFI/EMI, Electrical, Strain MIL-DTL-38999
Category 3B
AS85049/103 Relief, Straight, Self-Locking, (Composite) Series III 14, 15
Backshell, 90°, Self-Locking, Category 3C and IV Connectors
Non Self-Locking, Shield
MIL-DTL-38999 Series MIL-DTL-38999
AS85049/87 Band Termination, (RFI/EMI), 12, 13 RFI/EMI, Electrical, Strain Relief,
I and II Connectors AS85049/104 (Composite) Series III 14, 15
Shrink Sleeve Accommodation, 45°, Self-Locking, Category 3C
and IV Connectors
Category 3B
Backshell, Straight, Self-
MIL-DTL-38999
Locking, Non Self-Locking, RFI/EMI, Electrical, Strain Relief,
MIL-DTL-38999 Series AS85049/105 (Composite) Series III 14, 15
AS85049/88 Shield Band Termination, 14, 15 90°, Self-Locking, Category 3C
III and IV Connectors and IV Connectors
(RFI/EMI), Shrink Boot
Accommodation, Category 3B
Backshell, Straight, Non AS50151 Crimp, MIL-
Backshell, 45°, Self- Self-Locking, Self-Locking, Pre- DTL-26482 Series 2,
Locking, Non Self- AS85049/109 Attached Shield Termination AS81703 Series 3, and 6, 9, 20
Locking, Shield Band MIL-DTL-38999 (RFI/EMI), Boot Accommodation, MIL-DTL-83723 Series
AS85049/89 Termination, (RFI/ Series III and IV 14, 15 Category 3B III Connectors
EMI), Shrink Sleeve Connectors
Accommodation, Backshell, 90°, Non Self- AS50151 Crimp, MIL-
Category 3B Locking, Self-Locking, Pre- DTL-26482 Series 2,
AS85049/111 Attached Shield Termination AS81703 Series 3, and 6, 9, 20
Backshell, 90°, Self- (RFI/EMI), Boot Accommodation, MIL-DTL-83723 Series
Locking, Non Self- Category 3B III Connectors
Locking, Shield Band MIL-DTL-38999
AS85049/90 Termination, (RFI/ Series III and IV 14, 15
EMI), Shrink Sleeve Connectors Backshell, Straight, Non
Accommodation, Self-Locking, Self-Locking, Pre-
MIL-DTL-38999 Series
Category 3B AS85049/112 Attached Shield Termination 12, 13
I and II Connectors
(RFI/EMI), Boot Accommodation,
MIL-DTL-38999 Category 3B
Strain Relief, Straight,
(Composite)
AS85049/91 Self-Locking, Category 14, 15
Series III and IV
4C
Connectors Backshell, 90°, Non Self-
MIL-DTL-38999 Locking, Self-Locking, Pre-
MIL-DTL-38999 Series
Strain Relief, 90°, Self- (Composite) AS85049/114 Attached Shield Termination 12, 13
AS85049/92 14, 15 I and II Connectors
Locking, Category 4C Series III and IV (RFI/EMI), Boot Accommodation,
Connectors Category 3B

Termination, Shield, Split

Support Ring, Composite, Backshell, Straight, Non
AS85049/93 General Use N/A
Nonenvironmental, Self-Locking, Self-Locking, Pre-
MIL-DTL-38999 Series
Straight, Category 7 AS85049/115 Attached Shield Termination 14, 15
III and IV Connectors
(RFI/EMI), Boot Accommodation,
Mounting Device, Flange
Category 3B
Type, Full Perimeter,
AS85049/94 General Use N/A
Medium/Light Duty,
Category 7 Backshell, 90°, Non Self-
Locking, Self-Locking, Pre-
Mounting Device, Flange MIL-DTL-38999 Series
AS85049/117 Attached Shield Termination 14, 15
Type, 3/4 Mounting III and IV Connectors
AS85049/95 General Use N/A (RFI/EMI), Boot Accommodation,
Perimeter, Medium/Light
Category 3B
Duty, Category 7

Nut Plate for

Mounting
Connectors

Jam Nut for Panel Right Angle EMI Shielded Backshell

Mount Connectors

DMC does NOT provide connectors, backshells, accessories, or wiring components. Parts shown here are for reference only.

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 61
AS85049 CONNECTOR ACCESSORIES
QUICK REFERENCE GUIDE

SPECIFICATION TITLE APPLICATION PAGE SPECIFICATION TITLE APPLICATION PAGE

AS50151 Crimp, MIL- Connector Accessories, Fiber MIL-DTL-38999 Series

Backshell, Strain Relief, DTL-26482 Series 2, AS85049/131 Optic, Straight, Self-Locking, III and AS5590/1 14
AS85049/118 Straight, Self-Locking, Non AS81703 Series 3, and 6, 9, 20 Category 3B Connectors
Self-Locking, Category 4B MIL-DTL-83723 Series
III Connectors
Connector Accessories, Fiber MIL-DTL-38999 Series
AS85049/132 Optic, 45°, Self-Locking, III and AS5590/1 14
AS50151 Crimp, MIL- Category 3B Connectors
Backshell, Strain Relief, 90°, DTL-26482 Series 2,
AS85049/120 Self-Locking, Non Self-Locking, AS81703 Series 3, and 6, 9, 20
Connector Accessories, Fiber MIL-DTL-38999 Series
Category 4B MIL-DTL-83723 Series
AS85049/133 Optic, 90°, Self-Locking, III and AS5590/1 14
III Connectors
Category 3B Connectors

Backshell, Strain Relief,

MIL-DTL-38999 Series Connector Accessories, Fiber Fiber Optic Connectors
AS85049/121 Straight, Self-Locking, Non 12, 13 AS85049/134 N/A
I and II Connectors Optic, Filler Plug, Category 7 and Systems
Self-Locking, Category 4C

Connector Accessories, Fiber MIL-DTL-38999 Series

Backshell, Strain Relief, 90°,
MIL-DTL-38999 Series AS85049/135 Optic, Split, Straight, Self- III and AS5590/1 14
AS85049/123 Self-Locking, Non Self-Locking, 12, 13
I and II Connectors Locking, Category 3B Connectors
Category 4C

Connector Accessories, Fiber MIL-DTL-38999 Series

Backshell, Strain Relief,
MIL-DTL-38999 Series AS85049/136 Optic, Split, 45°, Self-Locking, III and AS5590/1 14
AS85049/124 Straight, Self-Locking, Non 14, 15
III and IV Connectors Category 3B Connectors
Self-Locking, Category 4C

Connector Accessories, Fiber MIL-DTL-38999 Series

Backshell, Strain Relief, 90°,
MIL-DTL-38999 Series AS85049/137 Optic, Split, 90°, Self-Locking, III and AS5590/1 14
AS85049/126 Self-Locking, Non Self-Locking, 14, 15
III and IV Connectors Category 3B Connectors
Category 4C

Use With SAE AS85049/138 Cap, Dust, Plastic, Category 9 General Use N/A
AS85049/118, /120,
AS85049/127 Bushing Strip, Category 7 N/A
/121, /123, /124, and
/126 Accessories Bushing, Cable Clamp to Cable,
AS85049//139 Telescoping For AS85049 General Use N/A
Cable Clamps, Category 9
Use With SAE
AS85049/82 -
Backshell, Shield Band, Boots, Heat-Shrinkable,
AS85049/128 /90, /109 - /117 52-55 AS85049/140 General Use N/A
Category 7 Straight, Category 9
Accessories, and
General Use
Boots, Heat-Shrinkable, 90°,
AS85049/141 General Use N/A
Category 9

Gasket Material, Conductive,

AS85049/130 Non Conductive, Flange Mount, General Use N/A Boots & Sleeves, Transitions,
Category 7 AS85049/142 General Use N/A
Heat-Shrinkable, Category 9

Band Termination System Shield Termination Bands

(Ref: AS85049/128)

EMI Shielded Backshells

for Rectangular Connectors

DMC does NOT provide connectors, backshells, accessories, or wiring components. Parts shown here are for reference only.

PAGE 62 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
TORQUE TIGHTENING REFERENCE
(FROM SAE-AIR 6151 STANDARD)
The SAE AIR 6151 Aerospace Information Report (Torque, Threaded Application, Electrical Connector,
Accessory and Terminal Board Installation) was the product of work by DMC and other experienced
aerospace wiring system designers, manufacturers, and component suppliers (including connectors
and backshells/accessories). We recommend the use of this valuable industry specification for
torque relating to connectors and other threaded components. The following tables reflect Torque
Values (based on Connector Classification) and are presented here as a quick reference guide. The
SAE AIR6151 is available at www.sae.org by typing AIR6151 into the search box, and following the
instructions for purchase and download.

CONNECTOR ACCESSORY* TORQUE/in-lb (Source SAE AIR6151)

Connector Shell Group 1 Group 2 Group 3 Group 4 Group 5
Sizes MIN/MAX MIN/MAX MIN/MAX MIN/MAX MIN/MAX
8,9,A 30/40 51/61 20/25 66/77 91/101
3,10,10SL, 11, B 30/40 71/81 20/30 103/113 115/125
7,12,12S,13,C 35/45 103/113 25/35 115/125 115/125
14,14S,15,D 35/45 111/121 25/35 139/149 139/149
16,16S,17,E 35/45 111/121 30/40 139/149 139/149
18,19,27,F 35/45 111/121 30/40 139/149 175/185
20,21,37,G 75/85 131/141 35/45 175/185 199/209
22,23,H 75/85 131/141 35/45 175/185 223/233
24,25,61,J 75/85 131/141 35/45 175/185 259/269
28,29 115/125 143/153 115/125 187/197 307/317
32,33 115/125 143/153
36 115/125 142/153
SEE PAGE 40 FOR INFORMATION
40 155/165 159/169
ON TORQUE APPLICATION TOOLING
44 155/165 159/169
48 155/165 159/169

Connector Accessory Recommended Torque (Backshell Installation)

Recommended torque for accessories such as those defined in SAE AS85049 to connector rear threads are listed
in the table above.
Group 1 is for aluminum connectors and medium/light duty accessories including connector series; AS50151
(AS31001 Series), MIL-DTL-26482 Series 1, MIL-DTL-26500, MIL-DTL-27599, MIL-DTL-38999 Series I and II,
MIL-C-81511 Series 1, 2, 3, 4, AS81703 Series 1.
Group 2 is for aluminum connectors and heavy duty accessories including connector series; AS50151 (AS34001
Series), MIL-DTL-22992, MIL-DTL-26482 Series 2, MIL-DTL-28840, MIL-DTL-38999 Series III and IV, AS81703
Series 3, MIL-DTL-83723 Series 1, 2, 3.
Group 3 is for connectors and accessories with composite (high grade engineering thermoplastic) material
coupling threads.
Group 4 is for connectors and accessories with aluminum coupling threads used in high vibration (engine)
applications.
Group 5 is for connectors and accessories with corrosion resistant steel coupling threads used in high vibration
(engine) applications.

*Source for torque values: AIR6151 Rev B.

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 63
TORQUE TIGHTENING REFERENCE
(FROM SAE AIR6151 STANDARD)

Typical Application - Torque Tightening a Connector Assembly

Recommended Connector Receptacle Jam Nut Torque/in-lb MIL-DTL-38999 (Source SAE AIR6151)
Recommended Recommended
Series I Series II Series III Series IV
Torque (Max/Min) Torque (Max/Min)
28/34 9 30/36 09
30/36 40/46 11
34/40 11 55/60 13 11
40/46 8 70/75 15 13
46/50 70/75 15
50/55 13 10 80/85 17
55/60 80/85 17
70/75 15 12 90/95 19
75/80 100/110 21 19
80/85 17 14 110/120 23 21
80/85 19 16 120/130 25 23
100/110 120/130 25
105/115 21 18
105/115 23 20 SEE PAGE 48 FOR DETAILS ON BETA
110/120 25 22 JAM-NUT TOOLING FROM DMC
120/130 24

PAGE 64 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
NATIONAL STOCK NUMBERS
FOR BETA™ SERIES TOOLING

DMC P/N NSN P/N DMC P/N NSN P/N DMC P/N NSN P/N DMC P/N NSN P/N

BT-AT-1500 5120-01-376-9839 CM288-33B 5120-01-377-4586 CM389S-8 5120-01-377-1273 CM5015R-32 5120-01-377-1333

BT-BS-601 5120-01-335-8841 CM288R-11A 5120-01-377-4603 CM389T-11A 5120-01-377-1302 CM5015R-36 5120-01-377-1298
BT-BS-609 5120-01-335-8842 CM288R-11B 5120-01-377-4534 CM389T-11B 5120-01-377-1178 CM5015R-40 5120-01-377-1316
BT-BS-610 5120-01-335-8843 CM288R-13A 5120-01-377-4545 CM389T-13A 5120-01-377-1215 CM5015R-44 5120-01-377-1202
BT-BS-611 5120-01-335-8844 CM288R-13B 5120-01-377-1327 CM389T-13B 5120-01-377-1297 CM5015R-48 5120-01-379-0200
BT-BS-618 5120-01-335-8845 CM288R-15A 5120-01-377-1269 CM389T-15A 5120-01-377-1172 CM5015R-8 5120-01-377-1238
BT-BS-625 5120-01-335-8846 CM288R-15B 5120-01-379-0154 CM389T-15B 5120-01-377-1200 CM815L-10A 5120-01-377-1312
BT-BS-630 5120-01-335-8847 CM288R-17A 5120-01-377-1182 CM389T-17A 5120-01-379-0146 CM815L-10B 5120-01-377-1264
BT-J-132 5120-01-368-4132 CM288R-17B 5120-01-377-1321 CM389T-17B 5120-01-377-1263 CM815L-14A 5120-01-377-1169
BT-ST-701 5120-01-335-8179 CM288R-19A 5120-01-377-1301 CM389T-19A 5120-01-377-4604 CM815L-14B 5120-01-377-1328
BT-ST-725 5120-01-335-8177 CM288R-19B 5120-01-377-1314 CM389T-19B 5120-01-377-1311 CM815L-16A 5120-01-377-1170
BT-ST-751 5120-01-335-8178 CM288R-23A 5120-01-377-1227 CM389T-21A 5120-01-377-1207 CM815L-16B 5120-01-377-4583
CM229-12 5120-01-377-1198 CM288R-23B 5120-01-377-1251 CM389T-21B 5120-01-377-1224 CM815L-18A 5120-01-377-4530
CM229-14 5120-01-377-1250 CM288R-25A 5120-01-377-1294 CM389T-23A 5120-01-377-1245 CM815L-18B 5120-01-377-4567
CM229-16 5120-01-377-1284 CM288R-25B 5120-01-377-1171 CM389T-23B 5120-01-377-1158 CM815L-20A 5120-01-377-1335
CM229-18 5120-01-377-1157 CM288R-29A 5120-01-377-1197 CM389T-25A 5120-01-255-7893 CM815L-20B 5120-01-377-1189
CM229-20 5120-01-377-4529 CM288R-29B 5120-01-377-1240 CM389T-25B 5120-01-377-1320 CM815L-22A 5120-01-377-4553
CM229-22 5120-01-377-1324 CM288R-33A 5120-01-377-4523 CM389T-9A 5120-01-377-1230 CM815L-22B 5120-01-377-4570
CM229-24 5120-01-377-1257 CM288R-33B 5120-01-377-1318 CM389T-9B 5120-01-379-0194 CM815L-24A 5120-01-377-1334
CM229-36 5120-01-377-1272 CM389B-11 5120-01-377-1234 CM389TR-11A 5120-01-377-1288 CM815L-24B 5120-01-377-4508
CM229-40 5120-01-377-4507 CM389B-13 5120-01-368-4117 CM389TR-11B 5120-01-379-0139 CM815L-8A 5120-01-377-4595
CM229L-28 5120-01-377-1319 CM389B-15 5120-01-368-4133 CM389TR-13A 5120-01-377-1252 CM815L-8B 5120-01-377-4543
CM229L-32 5120-01-377-1223 CM389B-17 5120-01-377-1261 CM389TR-13B 5120-01-379-0171 CM815L-10A 5120-01-377-4569
CM229L-44 5120-01-377-4578 CM389B-19 5120-01-377-1305 CM389TR-15A 5120-01-377-1188 CM815L-10B 5120-01-377-4519
CM229L-48 5120-01-377-1287 CM389B-21 5120-01-377-1208 CM389TR-15B 5120-01-379-0140 CM815S-14A 5120-01-377-4552
CM229L-52 5120-01-377-1187 CM389B-23 5120-01-377-1236 CM389TR-17A 5120-01-379-0193 CM815S-14B 5120-01-377-4581
CM264-10 5120-01-377-4551 CM389B-25 5120-01-377-1152 CM389TR-17B 5120-01-379-0191 CM815S-16A 5120-01-377-1308
CM264-12 5120-01-368-4118 CM389BR-11 5120-01-377-1186 CM389TR-19A 5120-01-379-0172 CM815S-16B 5120-01-377-1216
CM264-14 5120-01-368-4119 CM389BR-13 5120-01-377-1210 CM389TR-19B 5120-01-379-0161 CM815S-18A 5120-01-377-1310
CM264-16 5120-01-368-4120 CM389BR-15 5120-01-377-1244 CM389TR-21A 5120-01-379-0142 CM815S-18B 5120-01-377-1211
CM264-18 5120-01-377-4564 CM389BR-17 5120-01-377-1300 CM389TR-21B 5120-01-379-0180 CM815S-8 5120-01-377-1331
CM264-20 5120-01-368-4121 CM389BR-19 5120-01-377-1181 CM389TR-23A 5120-01-379-0173 CM837-10A 5120-01-368-4124
CM264-22 5120-01-377-4584 CM389BR-21 5120-01-377-1214 CM389TR-23B 5120-01-377-4535 CM837-10B 5120-01-377-1296
CM264-24 5120-01-377-4513 CM389BR-23 5120-01-377-1190 CM389TR-25A 5120-01-377-4605 CM837-12A 5120-01-377-1313
CM264-8 5120-01-377-1212 CM389BR-25 5120-01-377-1249 CM389TR-25B 5120-01-377-4568 CM837-12B 5120-01-377-1307
CM264R-10 5120-01-377-1233 CM389L-11 5120-01-377-1156 CM389TR-9A 5120-01-377-4600 CM837-14A 5120-01-368-4125
CM264R-12 5120-01-368-4123 CM389L-13 5120-01-377-1192 CM389TR-9B 5120-01-377-4527 CM837-14B 5120-01-377-1193
CM264R-14 5120-01-368-4122 CM389L-15 5120-01-377-1225 CM5015-10 5120-01-377-4562 CM837-16A 5120-01-368-4126
CM264R-16 5120-01-377-1256 CM389L-17 5120-01-377-1266 CM5015-12 5120-01-377-4602 CM837-16B 5120-01-377-1231
CM264R-18 5120-01-377-1291 CM389L-19 5120-01-377-1151 CM5015-14 5120-01-377-4536 CM837-18A 5120-01-368-4127
CM264R-20 5120-01-377-1149 CM389L-21 5120-01-377-1180 CM5015-16 5120-01-377-4547 CM837-18B 5120-01-377-1260
CM264R-22 5120-01-377-1203 CM389L-23 5120-01-368-4143 CM5015-18 5120-01-368-4147 CM837-20A 5120-01-368-4128
CM264R-24 5120-01-377-1222 CM389L-25 5120-01-368-4142 CM5015-20 5120-01-377-4587 CM837-20B 5120-01-377-1285
CM264R-8 5120-01-377-1239 CM389L-9 5120-01-377-1226 CM5015-22 5120-01-377-4526 CM837-22A 5120-01-368-4131
CM288-11A 5120-01-377-1271 CM389LR-11 5120-01-377-1259 CM5015-24 5120-01-377-4559 CM837-22B 5120-01-368-4129
CM288-11B 5120-01-377-1150 CM389LR-13 5120-01-377-1292 CM5015-28 5120-01-368-4146 CM837-24A 5120-01-368-4130
CM288-13A 5120-01-377-1179 CM389LR-15 5120-01-377-1161 CM5015-32 5120-01-377-4588 CM837-24B 5120-01-377-1162
CM288-13B 5120-01-377-1204 CM389LR-17 5120-01-377-1213 CM5015-36 5120-01-377-4518 CM837-8A 5120-01-377-1194
CM288-15A 5120-01-377-1235 CM389LR-19 5120-01-377-1267 CM5015-40 5120-01-377-1209 CM837-8B 5120-01-377-4560
CM288-15B 5120-01-377-1258 CM389LR-21 5120-01-377-1329 CM5015-44 5120-01-377-4574 CM837-8C 5120-01-377-1330
CM288-17A 5120-01-377-1332 CM389LR-23 5120-01-368-4145 CM5015-48 5120-01-377-1306 CM837-8D 5120-01-377-1147
CM288-17B 5120-01-377-1177 CM389LR-25 5120-01-368-4144 CM5015-8 5120-01-377-1201 CM837RB-10 5120-01-377-4571
CM288-19A 5120-01-377-4548 CM389LR-9 5120-01-377-1295 CM5015R-10 5120-01-377-4579 CM837RB-12 5120-01-368-4135
CM288-19B 5120-01-377-4565 CM389S-10 5120-01-377-4549 CM5015R-12 5120-01-377-4506 CM837RB-14 5120-01-368-4136
CM288-23A 5120-01-377-4609 CM389S-12 5120-01-377-4573 CM5015R-14 5120-01-368-4134 CM837RB-16 5120-01-368-4137
CM288-23B 5120-01-377-4524 CM389S-14 5120-01-377-1309 CM5015R-16 5120-01-377-1315 CM837RB-18 5120-01-368-4138
CM288-25A 5120-01-377-1326 CM389S-16 5120-01-377-1183 CM5015R-18 5120-01-377-1217 CM837RB-20 5120-01-368-4139
CM288-25B 5120-01-377-1278 CM389S-18 5120-01-377-1323 CM5015R-20 5120-01-377-1253 CM837RB-22 5120-01-368-4140
CM288-29A 5120-01-377-4514 CM389S-20 5120-01-377-1268 CM5015R-22 5120-01-368-4149 CM837RB-24 5120-01-368-4141
CM288-29B 5120-01-377-1317 CM389S-22 5120-01-377-4598 CM5015R-24 5120-01-410-7026 CM837RB-8 5120-01-377-1185
CM288-33A 5120-01-377-1243 CM389S-24 5120-01-377-1325 CM5015R-28 5120-01-377-1218

Additional NSNs may be available, consult DMC.

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM PAGE 65
 LIMITATION OF LIABILITY/
LIMITED WARRANTY*
LIMITATION OF LIABILITY:
DMC IS NOT LIABLE FOR
CONSEQUENTIAL OR
SPECIAL DAMAGES OF ANY
NATURE OR KIND RESULTING
FROM THE USE, MISUSE
OR UNAPPROVED USE OF
ANY OF ITS PRODUCTS.
OWNERS AND USERS OF
DMC PRODUCTS ASSUME
FULL RESPONSIBILITY
FOR INSTRUCTING THEIR
EMPLOYEES IN THE PROPER,
APPROVED, AND SAFE USE OF
SUCH PRODUCTS.
LIMITED WARRANTY: DMC warrants
each new product sold by it to be free
from defects in material and workmanship
under normal use and service. DMC’s
obligation under this warranty is limited to
the free correction or, at DMC’s option,
the refund of the purchase price of any
such product which proves defective in
normal service within ninety (90) days
after delivery to the first user, provided
that the product is returned to DMC with
all transportation charges prepaid and
which shall appear to DMC’s satisfaction,
after DMC’s inspection, to have been
defective in material or workmanship, it
being understood that DMC products are
not consumer products. This warranty
shall not cover any damage to any
product which, in the opinion of DMC,
was caused by normal wear, misuse,
improper operation, tampering, neglect,
or accident. This warranty is in lieu of all
other warranties express or implied. No
warranty, express or implied, is made
or authorized to be made or assumed
with respect to products of Daniels
Manufacturing Corporation other than
those herein set forth.

PAGE 66 © COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE: 407-855-6161 • E-MAIL: [email protected] • WWW.DMCTOOLS.COM
OTHER PRODUCTS FROM DMC

Contact our k­ nowledgeable staff

of customer s­ ervice ­application
experts for details on other q­ uality
products from DMC.
DMC tools have become the s­ tandard for
Military, Aircraft, Aerospace and Industrial use.
DMC can meet your needs for c ­ onnector s­ ystem
production and maintenance, f­astener retention
system and test/verification e
­ quipment for
compliance with SPC/ISO ­standards.

COMPLETE MAINTENANCE TOOL KITS

HAND OPERATED
CRIMP TOOLS

Safe-T-Cable® FASTENER
RETENTION SYSTEM

PNEUMATIC CRIMP TOOLS

ALPHATRON WIRE WIRE STRIPPERS AND

CRIMP PULL TESTERS REPLACEMENT BLADES

BATTERY POWERED
CRIMP TOOLS

© COPYRIGHT 2022 DANIELS MANUFACTURING CORP., ORLANDO, FL • PHONE:

© COPYRIGHT 407-855-6161
2022 DANIELS • E-MAIL:
MANUFACTURING [email protected]
CORP., ORLANDO, FL • PHONE:•407-855-6161
WWW.DMCTOOLS.COM PAGE 67
• E-MAIL: [email protected] • WWW.DMCTOOLS.COM