BHZ-RFCA

REPAIRMANUAL

OLYMPUS
BH2-RFCA

CONTENTS

A. OUTLINE OF PRODUCT
1. MERCHANDISE NAME AND CODE IN OLYMPUS . . . . . . ..e...... A-l
2. OUTLINE OF MERCHANDISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-l
3. FEATURES ............................................ A-l
4. RESTRICTED CONDITIONS ............................... A-l
5. SPECIFICATIONS ...................................... A-l

B. DISASSEMBLY
1. DISASSEMBLY OF WHOLE UNIT ........................... B-l
2. DISASSEMBLY OF HEAT ABSORPTION TUBE ASS'Y ........... B-8
3. DISASSEMBLY OF SHUTTER ASS'Y ........................ B-8
4. DISASSEMBLY OF LENS FRAME ASS'Y ..................... B-9
5. DISASSEMBLY OF AS ASS'Y ............................. B-9
6. DISASSEMBLY OF FS ASS'Y ............................. B-10
7. DISASSEMBLY OF CONNECTOR ............................ B-11
8. DISASSEMBLY OF DOVETAIL ASS'Y ....................... B-11
9. DISASSEMBLY OF DOVETAIL MOUNT ....................... B-12

C. ASSEMBLY AND ADJUSTMENT

1. ASSEMBLY OF DOVETAIL MOUNT .......................... C-l
2. ASSEMBLY AND ADJUSTMENT OF DOVETAIL ASS'Y ........... C-l
3. ASSEMBLY OF CONNECTOR ............................... C-2
4. ASSEMBLY AND ADJUSTMENT OF FS ASS'Y ................. C-2
5. ASSEMBLY AND ADJUSTMENT OF AS ASS'Y ................. C-4
6. ASSEMBLY OF LENS FRAME ASS'Y ........................ c-5
7. ASSEMBLY OF SHUTTER ASS'Y ........................... c-5
8. ASSEMBLY OF HEAT ABSORPTION TUBE ASS'Y .............. C-6
9. ASSEMBLY AND ADJUSTMENT OF WHOLE UNIT ............... C-6

D. JIGS, TOOLS AND CHEMICALS

1. JIGS AND TOOLS . ..s...................... ..C......... D-l
2. ADHESIVES AND GREASE .C.............................. D-l
BH2-RFCA A. OUTLINE OF PRODUCT

CONTENTS

1. MERCHANDISE NAME AND SYMBOL IN OLYMPUS . . . . . . . . . . . A-l

2. OUTLINE OF MERCHANDISE . . . . . . . . ..,...........I..., A-l

3. FEATURES . . . . . . . . . . ..".................$.......... A-l

4. RESTRICTED CONDITIONS ........................... ..A- 1

5. SPECIFICATIONS ................................... A-l

BH2-RFCA A. OUTLINE OF PRODUCT

1, MERCHANDISE
NAMEAND CODEIN OLYMPUS
Merchandise name Reflected light fluorescence
illuminator
CODE in OLYMPUS BH2-RFCA

2, OUTLINEOF MERCHANDISE
(1) This is the main unit (illuminator) of the reflected light
fluorescence system.

(2) For the outline of merchandise, refer to the GENERAL RULE for BH2-RFC.

FEATURES
Refer to the GENERAL RULE for BH2-RFC.

RESTRICTEDCONDITIONS
Refer to the GENERAL RULE for BH2-RFC.

SPECIFICATIONS
Item Specification Remarks

Main unit (1) Height 70mm (including trunk)

(BH2-RFCA)
(2) Width 14omm
dimensions
(3) Length 207.5mm excluding projections

Weight (1) Approx. 1.5kg

Observation tube (1) 1.25X

magnification Same as
B2-RFA
Number of visual (1) 20
fields

Microscope (1) Reflected light fluorescence and

inspection transmissive observation
method
(2) Reflected light fluorescence -
Transmissive differential inter-
ference (at use of BH2-ANF, BH2-
NAF, BH2-NCF or BH2-NC)
(3) Reflected light fluorescence -
Phase contrast (at use of BH2-PCM,
BH2-NCF or BH2-NC)

A-l
B:H2-RFCA A. OUTLINE OF PRODUCT

Item Specification Remarks

6 Iri.s (1) Aperture iris built in ($1 - 5

(2) Field iris (with a centering device) ($2 - 7
built in

7 Analyzer dummy (1) Square hole fitting with a click AB6765

(2) One supplementary barrier filter
demountable

8 Cube plate (1) Screw fixing type AB7281

9 Ultraviolet rays (1) Fitting/insertion type AB6743

protective shade

10 Nameplate (1) Magnet absorption type 9 types AB6754 - 62

11 Shutter (1) Slide type

(2) Aperture and ND25

12 1 Main body (1) Round dovetail (with a supplementary

foot)

2 Observation (1) Round dovetail (female side)

tube

3 Lamp house (1) Round hole fitting * Illuminator

BH2-RFCA

4 Power supply (1) Cable with a connector * Lamp house

unit BH2-LSl?F

* Cube slider

Flxlng with a screw

BH2-ANF

9 Analyzer dummy (1) Inserting into a square hole with a *BH2-RFCA

click

10 Analyzer (1) Inserting into a square hole with a * BH2-RFCA

slider BH2-ANF click

A-2
BH2-RFCA A. OUTLINE OF PRODUCT

Item Specification Remarks

11 Nomarski prism (1) Inserting into a square hole and * BH2-RFCA

slider BH2-NAF fixing with a screw

12 Prism cap (1) Inserting into a square hole and * BH2-RFCA

2 fixing with a screw
5
13 Ultraviolet (1) Inserting into a square hole and * BH2-RFCA
z
rays protective fixing with a spring
tJJ
.Z shade
+J
2 14 Nameplate (1) Fixing by magnet * BH2-RFCA
z -
15 Cube window (1) Fixing by magnet * BH2-RFCA
cover

16 Cube slider (1) Fixing with a screw * Cube slide

knob

13 1 Excitation (1) Slider with a click (with a stopper

a method at both ends)

s 2 Nomarski prism (1) Slider with a stopper

2 (2) Retardation with a fine adjustment

c .z screw
.: z
::z 3 Analyzer (1) Slider with a click
-
::
cx3 4 Shutter (1) Slider with a click

Asterisk (*) in the remarks column indicates

a matching part.

A-3
BH2-RE'CA B. DISASSEMBLY

CONTENTS

1. DISASSEMBLY OF WHOLE UNIT ....................... B-l

2. DISASSEMBLY OF HEAT ABSORPTION TUBE ASS'Y ....... B-8

3. DISASSEMBLY OF SHUTTER ASS'Y .................... B-8

4. DISASSEMBLY OF LENS FRAME ASS'Y ................. B-9

5. DLSASSEMBLY OF AS ASS'Y ......................... B-9

6. DISASSEMBLY OF FS ASS'Y ......................... B-10

7. DISASSEMBLY OF CONNECTOR ........................ B-11

8. DISASSEMBLY OF DOVETAIL ASS'Y ................... B-11

9. DISASSEMBLY OF DOVETAIL MOUNT ................... B-12

 BH2-RFCA B. DISASSEMBLY

\,> rl, DISASSEMBLY

OF WHOLEUNIT I
l-l Remove the A-PLATEa .

l-2 LoosetheKNOB@, and remove the

NAF dummy@.

B-l
BH2-RFCA B. DISASSEMBLY

l-3 Remove the KNOB@)by turning it

counter-clockwise, and remove the
COVER-R@.
* The COVER-R@is magnetic
type.

174 Remove the COVER-L@.

* The COVER-LOis magnetic
type.

Remove the NAMEPLATES@ (9 pieces).

* The NAMEPLATE@ is magnetic type. L/J

B-2
BH2-RFCA B. DISASSEMBLY

1-6 Remove the NAMEPLATE@.

SCREW PSK2x3SA 4 PCS.

l-7 Remove the HEAT ABSORPTION TUBE

ASS'Y@.

SCREW CSK3x8SA 4 PCS.

1-8 Remove the SHUTTER ASS'Y@and

the CLICK-SPRING @.

B-3
I3A2-RFCA B. DISASSEMBLY

1-9 Remove the ARM@ .

SCRFaWCUK3xlOSA 4 PCS.

l-10 Remove the KNURLED RING@.

.d

1-11 Remove the AS-ASS'Y@. d’

SCREW CSK2.6x8SA 3 PCS.

B-4
BH2-RFCA B. DISASSEMBLY

l-13 Remove the CONNECTOR@ .

SCREW 3x8SA 4 PCS.

l-14 Remove the LENS ASSlY@).

Remove also the following parts

at the same time.
* WASHERB
- LENS ASS'Y@
. DIAPHRAGM@

* The washer will be used for

parfocality adjustment in
assembling, and must not be lost.

LOWER-PLATE

B-5
BH2-RFCA B. DISASSEMBLY

l-15 Pull the SHAFTa, and remove the

DOVETAIL ASSlY@ .
* Loose the STOPPER SCREW@.

1-16 Remove the DOVETAIL ASS'Y 9.

SCREW AB3x4SA 4 PCS.

l-17 Remove the KNOB@.

B-6
BH2-RF'CA B. DISASSEMBLY

0-2 l-18 Remove the UPPER PLATEO . Remove

also the DOVETAIL PLATE@.
SCREW 3x8SA 4 PCS.
0
1
* The DOVETAIL PLATE@will be
used for parfocality adjustment
in assembling, and must not be
lost.

1-19 Remove the LOWER PLATE@).

03 SCREW 3x8SA 4 PCS.

‘,I<.il,,
::.1‘,,,:
?,‘,.
i,‘,

l-20 Remove the A-SPRING@.

SCREW 3PUK2x2SA 2 PCS.

B-7
 EIH2-WCA B. DISASSEMBLY

l-21 Remove the U-SPRINGa .

SCREW 3PUK2x4SA 2 PCS.

1 2, DISASSEMBLY
OF HEATABSORPTION
TUBE ASS'Y
2-l Remove the RING@by turning it --J
counter-clockwise, and remove the
FILTER@.
2-2 Remove the RING@by turning it
counter-clockwise, and remove the
LENS@.

HEAT-ABSORPTION-TUBE

--
.3, DISASSEMBLY
--_____-- OF SHUTTERASS'Y
1
d
3-l Remove the RING@by turning it
counter-clockwise, and remove the
FILTER@ m

3-2 Remove two KNOBS@.

B-8
 BH2-RFCA B. DISASSEMBLY

t 4, DISASSEMBLY
OF LENS FRAMEASS'Y

4-l Remove the LEVERa.-

4-2 Remove the AS-ASS'Y@.

SCREW0 ANU2x3SA 3 PCS.

4-3 Remove the RING @by turning it

counter-clockwise, and remove the
LENS@ .

j 5, DISASSEMBLY
OF AS ASS'Y
L
5-l Remove the INNER-FRAME@, and
take off four DIAPHRAGM-BLADES-RO .

06

B-9
 I3H:2-RFCA B. DISASSEMBLY

1 6, DISASSEMBLY
OF FS ASS'Y
6-l Remove the FIXING-SPRINGO .

6-2 Remove the LEVER-l@ .

6-3 Remove two KNOBS 0.

6-4 Remove SPRING HOUSING@.

Remove also the following parts
at the same time.
. SPRINGa
. SPINDLE@

6-5 Remove the RING@by turning it

counter-clockwise, and remove the
FS-ASS'@ .

6-6 Remove the INNER-FRAME@, and

take off eight DIAPHRAGM-BLADES-A
0.

B-10
 BH2-RFCA B. DISASSEMBLY

j 7, DISASSEMBLY
OF CONNECTOR 1
7-1 Remove the RINGaby turning it
counter-clockwise, and remove the
LENS 0.

18, DISASSEMBLY
OF DOVETAILASS'Y

Remove the SHAFTa.

Remove three R-KNOBS@.

Remove two COVERS 0.

SCREW PSK2x3 4 PCS.

8-4 Remove three SCREWS@.

The following parts come off at
the same time.

. Three SPRINGS@
' Three BALLS@

B-11
 E5l-r.2
-FTFCA B. DISASSEMBLY

--9, DISASSEMBLYOF DOVETAILMOUNT

L-____
9-1 Remove the SCREWa. Remove also
the following parts at the same
time.
. SPRING@
. BALLa

9-2 Remove the DOVETAIL@.

SCREW CUK2.6x8SA 3 PCS.

B-12
BH2-RFCA C. ASSEMBLY AND ADJUSTMENT

CONTENTS

1. ASSEMBLY OF DOVETAIL MOUNT ........................ C-l

2. ASSEMBLY AND ADJUSTMENT OF DOVETAIL ASS'Y ......... C-l

3. ASSEMBLY OF CONNECTOR ............................. c-2

4. ASSEMBLY AND ADJUSTMENT OF FS ASS'Y ............... C-2

5. ASSEMBLY AND ADJUSTMENT OF AS ASS'Y ............... C-4

6. ASSEMBLY OF LENS FRAME ASS'Y ...................... C-5

7. ASSEMBLY OF SHUTTER ASS'Y ......................... c-5

8. ASSEMBLY OF HEAT ABSORPTION TUBE ASS'Y ............ C-6

9. ASSEMBLY AND ADJUSTMENT OF WHOLE UNIT ............. c-6

 BH2-RFCA C. ASSEMBLY AND ADJUSTMENT

mAssEMBLY OF DOVETAILMOUNT
l-1 Attach the DOVETAILO .

SCREW CUK2.6x8SA 3 PCS.

1-2 Insert the BALLBand SPRING@,

and tighten the SCREW@.
* Apply grease to the BALL@and
SPRING@

GREASE LOS72515 (OT2008)

CUK2.6x8SA

2, ASSEMBLYOF DOVETAILASS'Y
i
2-l Insert the BALLa (3 PCS.) and
SPRING@ (3 PCS.), and tighten
the SCREW0 (3 PCS.).
* Apply GREASE to the BALLa
(3 PCS.) and SPRING@ (3 PCS.).

GREASE ~0~72515 (0~2008)

2-2 Adjust the click force.

(1) Set the supplied CUBE@ (B2-BF,
etc.).

(2) Measure the click force by using

a tension gauge (lkg).

Standard 5oog IL 1oog

(3) If a click force does not meet

the standard, adjust by changing
the inserting depth of the
SCREW@ (3 PCS.).

(4) Apply adhesive to the screw head..

Adhesive SHELLAC (OTl131)

~001 Tension gauge (&'1145)

C-l
 BH2-RFCA C. ASSEMBLY AND ADJUSTMENT

2-3 Attach the COVERa (2 PCS.).

SCREW PSK2x3SA 4 PCS.
* Apply an adhesive to the SCREWS .
Adhesive PERMA LOK (OT1126)
2-4 Attach the KNOB@ (3 PCS.).
* Apply small amount of grease to
the thread.
GREASE Los72515 (OT2008)
2-5 Attach the SHAFT@.
* apply adhesive to the thread.
Adhesive Araldite rapid(OT1315)

/_ 3, ASSEMBLYOF CONNECTOR UJ

Side with hard 3-l Insert the LENS@, and turn the
/ radius of curvature RING@clockwise.

* Pay attention to the lens

direction. (See the drawing.)
* Apply adhesive to the RING@.

Adhesive SHELLAC (OT1131)

-~___ --
I-4, ASSEMBLYANDADJUSTMENTOF FS ASS'Y J/
4-l Set the OUTER-FRAME@and DIAPHRAGM
BLADE-Aa (8 PCS.), and attach the
INNER-FRAME@.

06 * Pay attention to the front/back

side of the DIAPHRAGM-BLADEA@.
(See the drawing on the left.)
* Apply a thin coat of grease all
OUTER-FRAME around the INNER FRAME@.
q INNER-FRAME GREASE ~023P (0T2116)
\ r-d

c-2
BH2-RFCA C. ASSEMBLY AND ADJUSTMENT

4-2 Check the function of the DIAPHRAGM

BLADE-A@.
(1) Verify that the iris diameter is
smoothly varied from minimum to
maximum.
(2) Verify that the following
standard is met when the iris
diameter is minimum.

Drill of 1.3mm 4 passes,

but not 1.4mm.
Standard -
The ratio of longest side
to shortest side is 2:l
or less.

4-3 Insert the FS-ASS'Y into the

INNER-TUBE 0, and attach the
RINGO .
* Apply grease to both endfaces
and all around the FS-ASS'Y .
* The fine side of the RIMGO
should come to the iris side.

GREASE LOS72515 (0~2008)

Adhesive SHELLAC (OT1131)

4-4 Set the SPRING @ and SP1NDLEai.n

the SPRING-HOUSING 0 , and secure
it to the INNER-TUBE@.
* Apply grease to the ends of the
SPRING 0 and SPINDLE@..
* Apply adhesive to the thread of
the SPRING HOUSING 0 .
GR33ASE Los72515 (0~2008)
Adhesive SHELLAC (OT1131)

4-5 Attach two KNOBS@.

* Apply small amount of grease to
the KNOB thread.
GREASE LOS72515 (OT2008)

4-6 Attach the LEVER@.

* Apply adhesive to the lever
thread.
Adhesive SHELLAC (OT1131)
4-7 Attach the FIXING SPRING@.

c-3
 BH2-RFCA c. ASSEMBLY AND ADJUSTMENT

4-8 Adjust FS centering, and check the

open/close function.
(1) Move the two KNOBS 0, and verify
that FS moves vertically and
horizontally. Set it almost at
the center.
(2) Move the LEVER@ , and verify
that DIAPHRAGM BLADE opens and
closes smoothly.

r5, ASSEMBLYAND ADJUSTMENT

OF AS ASS'Y I
5-1 Set the DIAPHRAGM-BLADE-A@ (4 PCS.)
in the OUTER-FRAME@ , and attach
the INNER-FRAMEa .
* Apply small amount of grease to
the INNER-FRAMEa .

GREASE G023P (OT2116)

5-2 Check the open/close function.

@ Verify that the iris diameter
is smoothly varied Erom minimum
to maximum.
Dowe 1 :i
@ Verify that the following
standard is met when the iris
diameter is minimum.

Drill of lmm 6 passes,

but not l.lmm.
Standard
The ratio of longest
side to shortest side
is 3:l or less.

c-4
 BH2-RFCA C. ASSEMBLY AND ADJUSTMENT

1 6, ASSEMBLYOF LENS FRAMEASS'Y 1

6-1 Insert the LENS@, and turn the
RING@clockwise. (Use a PIN
FACE WRENCH .)
* The radius of curvature of the
lens is the same on both sides.
(no directivity)
* Apply adhesive to the RINGa
(at one point).
Adhesive SHELLAC (OT1131)

6-2 Apply adhesive to the AS ASS'Y ,

and fasten it tentatively with
three SCREWS@.
SCREW ANU2x3SA

6-3 Attach the LEVER@.

* apply adhesive to the thread.

6-4 Check the AS for opening and

closing.
Move the lever, and verify that
the spring opens and closes smooth-
ly.

/ 7, ASSEMBLYOF SHUTTERASS'Y
7-l Attach two KNOBS@.
* Apply adhesive to the thread.

Adhesive Araldite rapid

(OT1315)

7-2 Insert the FILTER@, and turn

the RING@clockwise.
* apply adhesive to the RING@.

Adhesive SHELLAC (OT1131)

c-5
 BH2-RFCA C.
~__ ASSEMBLY AND ADJUSTMENT

1- 8, ASSEMBLYOF HEATABSORPTION
--__ TUBEASS'Y
8-1 Insert the LENS @, and turn the
RING@clockwise.
Side with hard
radius of curvatur * Pay attention to the LENS@
direction. (See the drawing.)

0 ‘I 8-2 Insert the FILTER@,

RING@clockwise.
and turn the

8-3 Apply adhesive to the RINGsBand

0.

Adhesive SHELLAC (OT1131)

--___~
! 91, ASSEMBLYANDADJUSTMENTOF WHOLEUNIT
9-l Attach the U-SPRING@.

SCREW 3PUK2x4SA 2 PCS.

* Apply adhesive to the screws.

Adhesive PERMA LOK (OT1126)

I< 3PUK 2x4SA

9-2 Attach the A-SPRING@.

'%-3PUK 2x2SA

07 SCREW 3PUK2x2SA 2 pcs.

C-6
BH2-RFCA C. ASSEMBLY AND ADJUSTMENT

9-3 Adjust the A-SPRINGaclick force.

(See the preceding page.)

(1) Measure the click force when

pressing by using Bt12-ANF or
ANF DUMMY, and verify that the
following standard is met.
(Use a lkg tension gauge.)

Standard 5oog t 1oog

(2) If the standard is not met,

adjust by changing the A-SPRING
position.
* After adjustment, apply
adhesive to the screw.

Adhesive SHELLAC (OT1131)

~001 Tension gauge (sT1145)

9-4 Attach the LOWER PLATED.

SCREW AB3x8SA 4 PCS.

* Apply adhesive to the screws,

Adhesive PERMA LOK (OT1126)

3x8SA

9-5 Set the DOVETAIL-PLATE@used at

disassembling, and attach the
upper plate.

SCREW AB3x8SA 4 PCS.

9-6 Attach the KNOB@.

* apply grease to the thread.

GREASE LOS72515 (OT2008)

E3H%-RFCA C. ASSEMBLE AND ADJUSTMENT

9-7 Set BH2-NAF or NAF DUMMY@, and

verify that the it can be inserted
up to the stopper position and
securely fixed.

9-8 Verify that the UV-PROTECTIVE- d

SHADE@ can be securely mounted
and demounted.

9-9 Attach the DOVETAIL ASSlY@.

L.2)
SCREW AB3x4SA 4 PCS.

c-8
BH2-RFCA C. ASSEMBLY AND ADJUSTMENT

9-10 Insert the DOVETAIL-MOUNT@, mea-

sure and adjust the click force
and verify that the following
1 01
standard
gauge. 1
is met. (Use a lkg tension

- Tension gauge (lkg) OT1145

standard 7oog + 1oog
* If the standard is not met,
I adjust by changing the tightening
force of the screw which fixes
the DOVETAIL ASS'Y@ .
Faces meet each other. * After adjustment, apply adhesive
to the screw head.
Adhesive
SHELLAC
(OT1131)

I--.- SCREW
9-11 Adjust the dovetail's right angle.
(1) Set the jig as illustrated on the
left.
- COLLIMATORa KNoo47
- ADJUSTING MIRROR@ RFCAKCOOl
* ADAPTER FOR COLLIMATOR@RFCAKC002
. STANDARD CUBE@

(2) Verify that the dovetail's right

angle meets the following standard
at the middle cube position.
Standard Within half of
collimator scale
(3) If the standard is not met, ad-
just the tightening depth of the
SCREW@ (4 PCS.) and SCREW@(4pcs).
(4) Check for deviation from the center
at each cube position (3 positions),
and verify that the following
standard is met.
Standard Within 1.5 of colli-
mator scale
(5) Move the cube switching knob and
verify that the dovetail does not
rattle at each cube position.

c-9
BH;!-RE'CA C. ASSEMBLY AND ADJUSTMENT

9-12 Insert the DIAPHRAGM@, LENS-ASS'Y

@and WASHER@, and attach the
LENS ASSlY@.

LOWER-PLATE
* Use the same WASHER@which has
0 1 been disassembled.

02

9-13 Adjust the parfocality.

(1) Set the following jigs in BHS as
follows:
. STANDARD TUBE @ ;B-KN0003
. STANDARD OC @(for LB);KN0031
31
. STANDARD OB@ (for LB);KN0016
. STANDARD CUBE@RFCAKC004

(2) Check the parfocality, and verify

that the following standard is met.
standard Within +3 scale of
STANDARD OC @
(3) If the standard is not met, adjust
by selecting an appropriate washer.
(Refer to the list of washers given
List of washers on the left.)
(4) Apply adhesive to the LENS-FRAME@.
Adhesive SHELLAC (OT1131)

AB 3X8SA

I AB7016 tl. 2 I

L.---
AB7017
---
1~~70181
tl.
tl.
4
6 I
I I f
'1. 8
t2. 0

c-10
 BH2-RFCA C. ASSEMBLY AND ADJUSTMENT

9-14 Adjust the optical axis.

(1) Set the following jigs in BHS as
follows:
* STANDARD TUBE@ : B-KN0003
- STANDARD OC@ (for LB): KNOO30
- STANDARDOB@ (for LB): KNO015
' STANDARD CUBE@ : RFCAKC004

(2) Check the optical axis, and

verify that the following
standard is met.

~~

‘W AB 3x8s~
(3) If the standard is not met, adjust
by changing the UPPER-PLATEa
position.
SCREW AB3x8SA 4 PCS.
(4) Apply adhesive to the screw after
adjustment.
Adhesive SHELLAC (OT1131)

9-15 Attach the CONNECTOR ASS'Y .

SCREW AB3x8SA 4 PCS.
* Pay attention to the attaching
position. (See the drawing
below.)

AB 3x8SA
L CONNECTOR ASS'Y
UPPER PLATE

Hole position
OWER PLATE

c-11
BH2-,RFCA C. ASSEMBLY AND ADJUSTMENT

9-16 Adjust the optical axis.

(1) Set the following jigs in BHS as
follows:
* Objective 10X@
. MIRRORS (Parallel)(Equal grade
LP1576)
- STANDARD CUBE@ : RFCAKC004
. POSITIONING JIG FOR AB6736:@
RFCAKC003
* STANDARD REVOLVING NOSEPIECE@ :
35 B-KN0002
* STANDARD TUBE@ : B-KN0003
36 * STANDARD OCO (For LB): NO030
(2) Check the optical axis at each
cube position (3 positions), and
verify that the following standard
is met.
AB 3x8SA
I

06 (3) If the standard

by changing the
is not met, adjust
CONNECTOR ASS'Y@
position.
SCREW AB3x8SA 4 PCS.
(4) Apply adhesive to the four screws
after adjustment.
Adhesive SHELLAC (OT1131)

FS-ASS'Y 9-17 Attach the FS ASS'Y .

SCREW CSK2.6xlOSA 3 PCS.
* apply adhesive to the screws.
Adhesive PERMA LOK (OT1126)

c-12
BH2-RFCA C. ASSEMBLY AND ADJUSTMENT

9-18 Attach the AS ASS'YO .

I _l.-_l__, SCREW CSK2.6x8SA 3 PCS.

* apply adhesive (PERMA LOK MM) to

the screws.

Adhesive PERMA LOK MM (0~1126)

9-19 Adjust the AS iris center.

(1) Set the following jigs in BHS as

follows:
. STANDARD TUBE@B-KN0003

* CENTERING TELESCOPE@ : KNO029

. MIRROR@ (Parallel)(Equal grade
LP1576)
* OBJECTIVE 10X@
. STANDARD CUBE@ : RE'CAKC004

(2) Adjust the three screws so that

the AS center comes to the center
of the visual field.
* After the adjustment, apply
adhesive to the screws.
* Set the FS iris to the center
in the same manner.

SCREW ANU2x3SA 3 pcs.

6-x

AS-ASS'Y, // '\ \ Adhesive SHELLAC (OT1131)

/ .Y \
‘)
*

- ANU 2x3SA

c-13
BH2-RF'CA C. ASSEMBLY AND ADJUSTMENT

9-21 Attach the ARM@.

SCREW CUK3xl.OSA 4 PCS.

9-22 Set the CLICK-SPRING@, and

attach the SHUTTER-ASS'Y @.

* Apply small amount of grease to

the click groove of the CLICK-
SPRING@.

GREASE ~os72515 (0~2008)

c-14
BH2-RFCA C. ASSEMBLY AND ADJUSTMENT

9-23 Attach the HEAT-ABSORPTION-TUBE-

ASS'YO.

SCREW CSK3x8SA 4 PCS.

9-24 Attach the NAMEPLATE@.

SCREW PSK2x3SA 4 PCS.

9-25 Attach the NAMEPLATE@ (9 PCS.)

as illustrated on the left.
* The NAMEPLATE is magnetic type.
type.

4 U 9 IG

I 5 v

c-15
B’H2-RFCA c. ASSEMBLY AND ADJUSTMENT

9-26 Attach the COVER-LO .

* The COVER-LOis magnetic type.

type -

9-27 Set the COVER-Ra, and turn the d

KNOB@clockwise.
* The COVER-R@is magnetic type.
type.

d’
9-28 Insert the NAF-DUMMYBand fasten
it with the KNOB@.

9-29 Insert the ANF-DUMMY@.

c-16
BH2-RFCA D. JIGS, TOOLS AND CHEMICALS

CONTENTS

1. JIGS AND TOOLS .................................. D-l

2. ADHESIVES AND GREASE ............................ D-l

BH2-RFCA D. JIGS, TOOLS AND CHEMICALS

1. Jigs and Tools

I No. I Name I

B-KN0002 Standard nosepiece I

B-KN0003 Standard jig for mechanical tube length control

KNoo15 Centering objective for optical alignment (for long barrel)

KNO016 Standard objective for optical length adjustment (for long barrel)

moo29 Special centering telescope (d = 23.2mm)

KNoo30 Special eyepiece with cross hairs (long barrel)

KNoo31 Special eyepiece for optical tube length adjustment (for

KNoo47 Collimator

OT1145 Tension gauge (lkg)

WCAKCOOl Adjusting mirror for squareness

RFCAKCOO2 Adaptor for collimator

I WCAKC003 Positioning jig for AB6736

1 RFCAKCOO4 1 Standard cube

2. Adhesives and Grease

I No. I Name

I OT1126 Adhesive PEHMA LOK MM I

I OT1131 Adhesive SHELLAC

I OT1315 I Adhesive APALDITE RAPID I

I OT2008 I Grease Los72515

I OT2116 I Grease G023P I

D-l