TCG 01-G The TCG 01-G is a highly accurate, full featured

Global Navigation Satellite System (GNSS) clock

GNSS Clock trusted and proven for use in electricity
protection and control systems. The TCG 01-G
supports IEEE 1588v2 and conforms to IEC 61850.

Key Features The TCG 01-G can reference signals from either or both the GPS and
• References GPS and GLONASS GLONASS satellite networks. The clock synchronizes multiple IEDs
networks
(Intelligent Electronic Devices) within a network, including protection
• Multi-level password protection
relays and remote telemetry units, and provides time-stamps to all
• Independently isolated outputs
electronic data being generated by the IEDs.
• Isolated power supply
• High power line drivers
• Low noise characteristics due to Supports
balanced pair distribution • IEEE 1588-2008
• UTC and LST with user defined o IEEE C37.238-2011 Power Profile
DST options o IEEE C37.238-2017 Power Profile
• Remote configuration over o ITU-T G.8265.1 Telecom Profile (Slave only)
Ethernet o ITU-T G.8275.1 Telecom Profile (Full)
• Configuration Security o IEC 61850-9-3 Power Utility profile
• Enhanced security and
• DC IRIG-B or Modified Manchester
encryption that exceeds NERC
CIP requirements • AM IRIG-B (Modulated)
• Remote firmware upgrades • Serial Strings
• User defined pulses
• DCF77 Simulated time code
• NTPv3, NTPv4, SNTP
• Event Recording
Physical Inputs and Outputs
(W) 160 mm x (D) 155 mm x (H) 40 2 x independently programmable outputs, either:
mm, 0.8 kg, 1U 19” rack mount • TTL 0 - 5 V, 150 mA (BNC or 2-pin)
bracket accessory included IP40 • RS422 ± 5V differential, 50-unit loads (2-pin)
(Ingress Protection rating) • HV switch MOSFET 250V 100 mA (2-pin)
• Fiber TX (62.5/ 125 µm, λ 820 nm), compatible with multi-mode fiber (ST
Fiber connectors)
• Minimum optical power -22.8dBm, if using Tekron ITR, typical optical power
Front Panel budget 6.6dB
The TCG 01-G has a 2-line x 16 Timing accuracy: <100 ns to UTC
character FSTN LCD display and two
1 x RS232/ RS422 serial port, DCE wired (DB9)
LEDs indicating multiple statuses,
• RS232: Signals are +/- 9 V, 10 mA.
including:
• Serial time messages can be configured to be output at 1200,
2400,4800, 9600, 19200 and 38400 baud. Programmable pulse or
• Sync Status IRIG-B available on pin 1.
• Satellite acquisition mode Timing accuracy of RS232/ RS422 port:
• Alarm • Serial Message: <1 bit time typical to UTC
• Display mode button • Pulse/ or IRIG-B time code: <1.5 μs to UTC

1 x AM IRIG-B, 8 Vpp, 120 ohm (BNC)

GNSS Receiver Timing accuracy: <2 μs to UTC
L1, C/ A code, 32 Channel Parallel- 2 x Event recording inputs/ DC IRIG-B inputs (2 pin) Input rating: 5 V, 7 mA (10
tracking receiver V, 20 mA also accepted) Timing accuracy <100 ns.
Frequency: Minimum threshold voltage: 4.15V
1598 MHz
1 x Antenna fail alarm (2 pin - Form A contact) Contact rating: 200 V, 150 mA DC
Sensitivity: or 150 V, 100 mA AC
• Acquisition: -148 dBm
• Tracking: -160 dBm 1 x Sync relay (2 pin - Form A contact) Contact rating: 200 V, 150 mA DC or 150
V, 100 mA AC

1 x SMA Female Antenna Connector

Oscillator – TCXO • 5V DC @ 50mA antenna power supply
Holdover characteristics operating • 50Ω Impedance
at 25C:
1 x RJ45 10/100 Mbps UTP connector
• TCXO 1PPS drifts 0.55 ms over a • Timestamping accuracy: <100 ns to UTC
(NTP/SNTP + PTP)
24 hour period.
• Protocols Supported:
• Drift rate: 7 ppb per second ARP, UDP, ICMP, TFTP, DHCP, VLAN.
• Auto MDIX
• Auto Negotiate
Fiber IRIG-B Input Option
Back Panel:
• ST Fiber (62.5/12.5μm λ
820nm)
• Minimum guaranteed optical
power threshold -24dBm
• if using Tekron ITR, typical
optical power budget 6.6dB
Configuration Software Programmable Outputs
Windows based configuration • IRIG-B (B00x / B22x) time code with selectable C37.118.1 and AFNOR
software is available for download S87-500 extensions
on the Tekron website. Remote • DCF77 time code, 1 kHz square wave
configuration over Ethernet • User defined pulse sequences:
includes the following user Repetition rates from 20 ms to 24 hours
adjustable features: Offsets and durations from 10 ms to 24 hours
• Multi-level access control
• Privacy & authentication Serial Strings
methods equivalent to SNMP • NMEA-0183 ZDA
USM • NMEA-0183 RMC
• “Supervisor-mode” prevents • IRIG J-17
non-approved changes • Tekron A - H (Eight protocols for plug and play compatibility with a
• Test mode wide range of equipment).
• Commissioning tool
SNMP
Timing & Synchronization • v1, v2c & v3 support can be independently enabled
Worldwide daylight savings and • Configurable v1, v2c community names & security groups
local time configuration using either • Fully configurable via SNMP
rule based or fixed date methods. • v3 User-based Security Module (USM) support
Options that allow equipment • USM authentication methods: MD5, SHA
checks prior to full installation and • USM privacy methods: DES, AES
adjustable hold-over times to • USM MIB support
increase reliability in the case of • Notifications
poor GNSS coverage. Adjustments • SNMP trap generation v1, v2c & v3
to compensate for installation • SNMPv3 traps can be authenticated & privatized via USM
parameters such as delay of GNSS • Syslog (RFC-3164 & 5424 varieties)
signal through antenna cable.
Environment and Electrical
Power Supply: L=14-36 Vdc (2 pin)
Contact Us M=20-75 Vdc (2 pin)
• www.tekron.com H=90 -300 Vdc (2 pin)
• Phone: +64 4 566 7722 • Power drain: 6W max
• Sales Freephone: (Australia) • Operating temperature:
1800 506 311 -10 to 65°C
• Sales Freephone: (North • Humidity: To 95% RH
America) 1800 256 2309 (non-condensing)
Note: • Isolation:
The quickest and most effective Outputs to base unit: 2.5 kV
method to request a quote is Power supply to I/O: 3.5 kV
through the online quote request
form on the Tekron website.