Scribd
Upload
137 views2 pages

Cape Cod Plan 8 FT 8 FT Double Central

This document provides the materials list and dimensions for a double Cape Cod rail gate with two 8-foot wide gates hung between central eye hinge posts. It includes the hardware required, such as central eye hinge sets, cane bolts, and throw over gate loops. Lumber requirements are listed for the posts, rails, stiles, and diagonals. Fastener quantities are also specified.

Uploaded by

Leandro Picoloto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
137 views2 pages

Cape Cod Plan 8 FT 8 FT Double Central

This document provides the materials list and dimensions for a double Cape Cod rail gate with two 8-foot wide gates hung between central eye hinge posts. It includes the hardware required, such as central eye hinge sets, cane bolts, and throw over gate loops. Lumber requirements are listed for the posts, rails, stiles, and diagonals. Fastener quantities are also specified.

Uploaded by

Leandro Picoloto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DOUBLE CAPE COD RAIL GATE (TWO 8 FOOT WIDE 46” HIGH GATES)

CENTRAL EYE HINGES (Product Codes #8312) GATE HUNG BETWEEN POSTS
Distance between gate and hinge post A
Width of Left Gate B
Distance between gates C
Width of Right Gate D
Distance between gate and hinge post E
Total distance between posts F

Hardware Required
Galvanized Finish Black Powder Coat over Galvanized Finish Central Eye Hinge Advantages
Hinge Sets 2 of 8312-S242 2 of 8312-S24P
fasteners included Two Sets Includes Opens both ways 100 degrees
with hardware two 24 inch double strap (8312-542 or 8312-54SP) Incredible amount of adjustment
two adjustable bottom gate fitting (8250-002 or 8250-00P) Easy operation
four 12" adjustable gate pin (8800-122 or 8800-12P) Very strong
Cane Bolt (Vertical) 1 or 2 of 5000-242* 1 or 2 of 5000-24SP*
Dimensions (feet and inches)
Central Latch Options
A B C D E F
Throw Over Gate Loop 4200-032 4200-03SP 4.5" 8' 1" 8' 4.5" 16' 10"
Cane Bolt and Keep 5000-122 plus 5000-002 5000-12SP plus 5000-00SP 4.5" 8' 1" 8' 4.5" 16' 10"
Lumber Required
Posts 2 of 10' x 6" x6" (usually dressed out at 5.5" x 5.5")
Rails, Stiles (uprights) and Diagonals made from full 1" thick by 5.5" wide lumber (commonly stocked decking material or rough cut lumber)
Rails 8 of 8' x 1" x 5.5"
Stiles 6 of 8' x 1" x 5.5"
Diagonals 4 of 10' x 1" x 5.5"
Filler Blocks 4 of 10' x 1" x 5.5" (Parts E,F, and G on Plan Layout)
Fasteners Required
Approximately 100 of 1.75" x #8 wood screws (stainless preferred)
32 of 3.5" x 3/8" carriage bolts (hot dipped galvanized or stainless steel), nuts, and washers
*One 24" Cane Bolt (5000-242 or 5000-24SP) is required for central stability. Two are needed if you require a means of keeping the gates open.
Hoover Fence Company
Download includes this materials list, component cutting and layout sheet, tips on installing gate posts, and detailed instructions.
For a complete listing of our free gate plans and gate layouts visit hooverfence.com.

You might also like