NOTES:
0. ALL DRAWINGS ARE IN METRIC MEASUREMENTS
1. ALL ENGINEERING PRACTICES SHALL BE APPLIED WITH REGARDS TO HOLE AND SHAFT TOLERANCES.
2. WHERE SCREWS OR BOLTS ARE USED THE CLEARANCE HOLES SHALL BE APPROXIMATELY 5% TO 8% LARGER THAN THE MATCHING TAPPED HOLE.
3. PREFERABLY ALL TAPPED HOLES AND MATCHING SCREWS AND/OR BOLTS TO BE METRIC FINE (MF)
4. MATERIALS SPECIFIED ON THE DRAWINGS ARE INDICATIVE ONLY. THE BUILDER CAN MAKE HIS/HER OWN MATERIAL CHOICE.
5. ALL CONNECTIONS/JOINTS WHICH HAVE STEAM PRESSURE APPLIED TO IT SHALL BE SILVER/HARD SOLDERED.
6. COMPRESSION SPRINGS ARE DRAWN IN COMPRESSED STATE (CP), UNCOMPRESSED STATE IS APPROX 40% TO 60% LONGER THEN COMPRESSED STATE.
7. WHERE PREFERRED SCREW OR RIVETED CONNECTIONS CAN BE OMITTED AND PARTS CAN BE BONDED TOGETHER BY USING EITHER HIGH STRENGTH GLUE, EPOXY
RESIN, OR SOLDER.
8. PARTS WHICH ARE DIRECTLY EXPOSED TO STEAM AND/OR WATER SHOULD BE CONSTRUCTED USING NON-FERROUS OR NON CORROSIVE MATERIAL SUCH AS
BRASS, BRONZE, GUNMETAL, STAINLESS STEEL, COPPER OR MONEL.
9. THE ORDER IN WHICH THE PARTS/COMPONENTS ARE MANUFACTURED AND THE MODEL IS ASSEMBLED IS ENTIRELY LEFT TO THE BUILDER/MODEL MAKER.
10. A COLOUR SCHEME FOR THIS PROJECT IS ENTIRELY LEFT UP TO THE MODEL MAKER.
11. THE MANNER IN WHICH THE PARTS/COMPONENTS ARE MANUFACTURED IS ENTIRELY LEFT UP TO THE BUILDER.
12. USE LOCTITE, ON SCREW OR PRESS FIT CONNECTIONS OR SURFACES, WERE DEEMED NECESSARY TO PREVENT PARTS FROM LOOSENING.
13. WASHERS AND/OR SPRINGWASHERS SHALL BE USED WHERE DEEMED NECESSARY.
XX. ERRORS AND/OR OMISSIONS MAY OCCUR IN THE DRAWINGS, DO NOT HESITATE TO CONTACT ME SO THAT THE ERRORS/OMISSIONS CAN BE RECTIFIED.
MATERIAL ABBREVIATIONS:
ALU = ALUMINIUM
HALU= HARD ALUMINIUM
BRS = BRASS
BRZ = BRONZE OR GUNMETAL (BRZ/GM)
CI = CAST IRON
CU = COPPER
GRA = GRAPHITE
MS = MILD STEEL/BRIGHT MILD STEEL
SS = SILVER STEEL OR STAINLESS STEEL
SPS = SPRING STEEL
PEEK= POLYETHER ETHER KETONE OTHER ABBREVIATIONS
SYN = SYNTHETIC MATERIAL SUCH AS VETON, NYLON, TEFLON AS = AS SHOWN
OR RUBBER DP = DEEP
IN GENERAL SYNTHETIC MATERIALS SOULD BE ABLE TO DAA= DRILL AFTER ASSEMBLY
WITHSTAND THE HEAT AND PRESSURE(S) APPLIED TO D&TAA= DRILL AND TAP AFTER ASSEMBLY
THEM. CF = CLOSE FIT (SIZE FOR SIZE)
nnn/nnn MEANS THAT EITHER MATERIAL CAN BE USED PF = PRESS FIT
PFAA= PRESS FIT AFTER ASSEMBLY
PCD = PITCH CIRCLE DIAMETER
RM = REAM
HEX = HEXACON, 6SIDED
STEAM IN CP = COMPRESSED
KNL = KNURLED
CSK = COUNTERSINK
PL = PLACES
DWL= DOWEL
SPF= SPOTFACE
(T)HESOP=(TAPPED)HOLES EQUALLY SPACED ON PCD
(T)HESOC=(TAPPED)HOLES EQUALLY SPACED ON
CIRCUMFERENCE
OD = OUTSIDE DIAMETER
ID = INSIDE DIAMETER
MAX/MIN = CRITICAL DIMENSION
SA-xxx = SUB ASSEMBLY-xxx
QTY. PART NUMBER
1 09D-22-00-1-01-BASE FRAME
1 09D-22-00-1-02-CLINDER BLOCK
1 09D-22-00-1-02-CLINDER BLOCK
1 09D-22-00-1-03-VALVE CHEST
2 09D-22-00-1-04-MAIN BEARING
1 09D-22-00-2-01-CRANKSHAFT
2 09D-22-00-2-02-PISTON+CROSSHEAD
2 09D-22-00-2-03-CON-ROD
2 09D-22-00-2-04-SLIDE VALVE
2 09D-22-00-2-05-SLIDE VALVE GUIDE
2 09D-22-00-2-06-SLIDE VALVE REVERSER LINK
1 09D-22-00-2-07-SLIDE VALVE PARALLEL LINK
2 09D-22-00-2-08-ECCENTRIC
2 09D-22-00-2-09-ECCENTRIC STRAP
1 09D-22-00-2-10-REVERSER HANDLE
93.5 3.7
14 09D-22-00-M3 NUT
16 09D-22-00-M3x12 A-K CYL HEAD SCREW
2 09D-22-00-M3x6 A-K GRUB SCREW
28 09D-22-00-M3x9 A-K CYL HEAD SCREW
1 09D-22-00-M4 DOME NUT
14 09D-22-00-M4 NUT
4 09D-22-00-M4 WASHER-SPECIAL
4 09D-22-00-M4 WASHER
18 09D-22-00-M4x10 A-K CYL HEAD SCREW
4 09D-22-00-M4x14 A-K CYL HEAD SCREW
4 09D-22-00-M4x20 A-K CYL HEAD SCREW
1 09D-22-00-M4x5 A-K GRUB SCREW
275 10.8 STEAM OUT 4 09D-22-00-M5 NUT
190 7.5 4 09D-22-00-M5x14 A-K CYL HEAD SCREW
2 09D-22-00-M6 NUT
NOTES: DESIGNED BY J.A.M. DE WAAL
TITLE PROJECTION
DRAWING CONTENTS PROJECT No 09D-22-00 MODEL SCALE: 1:1
JDWDS
EXPERIMENTAL 2 CYL. HORIZ. STEAM ENGINE GENERAL ARRANGEMENT, NOTES, JDW DRAUGHTING SERVICES
J.A.M. DE WAAL. 12 BRIGHTWELL STREET PAPAKURA
DATE
JANUARY 2021
DWG SCALE: 1:1 @A3 OR AS SHOWN
J.A.M. DE WAAL PAPAKURA NZ
Copyright ©
USING THE SLIDE VALVES AS REVERSER ISOMETRIC VIEW, BILL OF MATERIALS SHEET: 01 OF 04 A3 No: 09D-22-00-SHT01
2110. NEW ZEALAND. PHONE: OO64 09 2988815. MOB:
0211791000 E-MAIL: [email protected].
DRAWINGS ARE FOR PERSONAL USE ONLY NOT FOR COMMERCIAL PURPOSES
