LIQUID GLASS

15 - 35 ° C and the surface temperature to be applied should

be at least 5 ° C. It should not be applied in rainy weather. For
good adhesion, surface cleaning should be done very well. APPLICATION CONDITIONS
Any kind of oil, dust, dirt, rust and similar substances on the
IMPORTANT and RISKS
surfaces to be applied between the liquid glass and the floor The surface should be protected The application surface must be clean
Things to
which may prevent the liquid glass from sticking to the surface from rain, water, mechanical loads consider during and free from all impurities like dirt, oil,
and mud. The joint fillings should be
and after the
and impacts for 24 hours during and
should be completely cleaned. In tile, ceramic applications, if after the application.
application renewed if current ones abraded in
ceramic, tiles applications.

ISONEM LIQUID GLASS is a two-component product which existing joint fillings were worn away, they should be B component should be used Other ISONEM X
immediately after opening. It is not products
excellent adheres to surface like glass, mosaic, tile, porcelain, renewed. The sanded surface provides better mechanical appropriate to re-use an opened recommended

ceramic, marble, granite, natural stone, wood, concrete, properties for liquid glass application and helps to better packaging that took air. Application
temperature
It should be applied between 5 - 35
°C.
screed, galvanized sheet, aluminum etc.. The product which adhesion of the liquid glass to the surface. Pot life 50 – 60 minutes

has a high resistance to atmospheric conditions can be used Application Method : Before application, the two compo-
for waterproofing and decorative purposes. Produced in trans- nents must be mixed thoroughly and at the given ratios. The
parent the product has high chemical and physical besides two components can react only when the mixture is uniform
excellent water resistance. It is not affected by U.V and and complete. The number of floors to be applied for the best
outdoor weather conditions. It does not make yellowing, performance is indicated in the table below.

General Features
fading or peeling off in time. It is especially applied as a
solution to insulation problems arising on the floors such as TECHNICAL SPECIFICATIONS
balconies, terraces, bathrooms easily and without damaging · Pot Life (hours, 20°C) : 1 (may vary depending on ambient
Provides %100 B fl S1
Waterproofing Fire Class
the existing coating. temperature)
· Touch-free Drying (hours, 20°C) : 1 - 2 (may vary depending
USAGE AREAS on application surface, application fullness, and humidity.)
· Glass, glass brick, mosaic, mosaic tile, · Hardening Time (hours, 20 ° C) : 18 - 24 (relative humidity of Excellent
Adhesion
Fast
Drying
· Tiles, ceramics, marble, granite, natural stone, porcelain the air should be less than 80 %.)
surfaces · Full cure reaction time : 7 days
· In press bricks, CONSUMPTION : 0,150 - 0,200 kg/m² (two layers). 20 - 26 m² /
· On wooden surfaces, 4 kg set, 10 - 13 m² / 2 kg set
· Balcony, terrace, bathroom, kitchen, stone-covered exterior. PACKAGING : 4 kg set (Component A: 3,5 kg, Component B:
· Ceramic, glass mosaic covered ornamental pools. 0,5 kg), 2 kg set (Component A: 1,75 kg + Component B: 0,25
· It helps to prevent dusting on absorbent surfaces. kg)
SHELF LIFE : 24 months from date of production if stored in
APPLICATION INFORMATION original, unopened, undamaged packages.
Surface preparation : The relative humidity of the air should STORAGE CONDITIONS : Store tightly closed in a dry and cool
be maximum 80%, the ambient temperature should be place away from heat and fire.

CONCRETE MARBLE, GRANITE RAW WOOD TILE, CERAMICS MEMBRANE, SHINGLE STEEL, METAL
Application In the same direction as the first layer Horizontal In the same direction as the first layer Horizontal X
Horizontal
Surface Humidity Dry surface Dry surface Dry surface Dry surface X
Dry surface
Application Tools Roller (synthetic epoxy), brush, spray Roller (synthetic epoxy), brush, spray Roller (synthetic epoxy), brush, spray Roller (synthetic epoxy), brush, spray X Roller (synthetic epoxy), brush, spray

Primer Usage X X X X X X
Primer Consumption X X X X X X
Product Usage 2 Layers 1 Layer 2 Layers 1 Layer X 1 Layer
Product Consumption 150 - 200 g / m² ( 2 Layers ) 75 - 100 g / m² (1 Layer) 150 - 200 g / m² (2 Layers) 75 - 100 g / m² (1 Layer) 75 - 100 g / m² (1 Layer)
X
Between Two Coats 4 - 24 Hours X 4 - 24 Hours X X X
Touch-free Drying 1 - 2 Hours 1 - 2 Hours 1 - 2 Hours 1 - 2 Hours X 1 - 2 Hours
Through Drying 7 Days 7 Days 7 Days 7 Days X 7 Days

Note : Drying times are approximate data, it may vary depending on ambient conditions.

The information given in this technical data sheet has been prepared according to our knowledge, experiment results, and experiences. The correct and successful implementation of our products is completely beyond our control and responsibility. For this reason, our responsibility is
limited to the quality of our product only, and this manual overrides all previous technical statements, descriptions and label information. 18