TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE. IMET Spa Loc. Tre Fontane - Cisano Bergamasco Tel. 035/4387911 - Fax. 035/787066 ; Web site: www.imetsaws.com a E-mail: [email protected] Manual Band Sawing Machine GBS 242 Autocut INSTRUCTIONS FOR USE 3 LES GBS 242 AutoCut ED.2016 eng rev.00 1/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE ommend to read carefully the information here included in order to install, use and maintain correctly and safely this machine. Please refer always to this instruction manual in case of assistance service need and keep it carefully for all the machine life. PLS CALL +390354387918 or +390354387928. 4 consequence of the continuous improvement of the product is that some images/descriptions here included could not correspond to the improved features of the machines. Your kind collaboration would help us in intevening asap. In the enclosed Compliance Declaration you will find the Safety and Reference Norms applied during the planning and construction of this machine. The choice and the use of the parts have been made by considering the conditions of use and the long machine life, The identification plate, with the serial number, is fixed on the control box right angle ; 4.1 ATTACHED DOCUMENT FOR E.M.C. (INDUSTRIAL ENVIRONMENT) The user is responsible for the installation and use of this machine in compliance with the manufacturer's instructions shown in this manual. This equipment meets the protection requirements in accordance with the Directives 2006/42/EEC, and 2004/108/CE for Electromagnetic Compatibility (EMC). In particular, it follows the technical guidelines of the Directives EN55011, EN50082-2 and it has been made for industrial and not for household use In the event of electromagnetic interferences the user is responsible for solving the problem with the help of the technical assistance by the manufacturer. Before installing the machine the user must take into account possible electromagnetic problems of the working area. In particular, we suggest to install the machine away from -signalling, control and telephone cables; ~racio-television transmitters and receivers; computers or controlling and measuring instrument; -safety and protection devices. The electric supply cable must be kept as short as possible, without any twists, Covers, doors and the frame must be suitably closed when the saw is operating, Under no circumstances the machine must be modified except for adjustments and changes specifically approved by the manufacturer. Follow the maintenance schedule. GBS 242 AutoCut ED.2016 eng rev.00 2/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE CE DECLARATION OF CONFORMITY (enc. THE MANUFACTURER : IMET S.p.A Localita Tre Fontane 24034 - CISANO BERGAMASCO -BG- ITALIA HEREBY DECLARES THAT in designing and manufacturing the machine described here below , we have considered the m important requirements of safety and health dictated by the European Directives of the Mac’ Security, Remember that this declaration loses its validity if machine is modified without our agreement. Trade name BAND SAWING MACHINE FOR METALS Code / Model / Type Manufacturing year ORIGINAL WITHIN THE MACHINE. Serial number —_— "BREE PN AU) 2CETOF YRECEUROPEAN PARLIAMENT AND OF THE COUNCIL OF TI 17TH/05/2006 REGARDING THE MACHINES AND THAT MODIFIES THE DIRECTIVE 95/16/CE: DIRECTIVE 2004/108/CE OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF THE 15/12/04 REGARDING THE ELECTROMAGNETIC COMPATIBILITY -EMC- DIRECTIVE 2006/95/CE OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF THE 12/12/06 REGARDING ELECTRICAL EQUIPMENT FOR USE OF LOW VOLTAGE -LVD- HARMONIZED STANDARDS REFERENCE EN.12100-1- EN12100-2; EN 55011, EN50082-2, EN 13898, EN 60204 LEGISLATIVE DECREE N.17 OF THE 27TH OF JANUARY 2010. AND AUTHORIZING THE PERSON LISTED BELOW TO ISSUE THE TECHNICAL FILE. Date: 01.01.2012 The signatory identification ‘The manager Angelo MeroniTRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE STANDARD VERSION COMPLETE WITH: electrical components complying with E.C. Norm EN60204-1, EN55011, EN50082-2, low voltage (24V) with start button inside the handle of the control lever, micro switches on the band protection ‘guard and on the band tensioner. Front screw vice with quick locking and fast positioning, it slides transversally from left to right along the workplane. Jaws of 135 mm height, quick and positive location at 0, 45 and 60 deg. left; base with 15 liter coolant tank and pump, composable floor stand with front door, blade brush, saw frame retum spring, bi-metal band, and manual of instructions. Available versions: Autocut : same features of the manual version plus the “Autocut System”, which takes advantage of the sawframe weight to make autonomous cuts with adjustable downfeed speed. Manual lifting of the sawframe after the cut. The technical specifications that you will find in the following tables serve to have a general evaluation of the machine and its performances. On not differently indicated, all data reported in this manual refer to the standard version, suitable for working at 400 V / 50 Hz if THREEPHASE. REO at: ‘ = cutting capacity( max. allovable dimensions) = blade dimensions Mb — weignt __M#™ =vice opening « @ =motor choice, minimum power, and blade speeds (at 50 Hz): — « |@l/e|/a eyo eI mm. Min. Kw |Mt/min| mm. | Kg. mm. [mm. |mm. 2965x27%0,9 |i,1/1,3 [35-70 |300 [290 Wm (250 [210 290x210 30 a [220 [200 | 210x100 LEFT eee [140 [130 | 140x130 LEFT 45° 170__[470__ | 470x170 RIGHT If the minimal lubrication is installed, the maximum capacities are reduced by about 10 mm Dimensions B L H nh (mm) width lenght height worktable height In use 1250 1500 1700 ‘Min.940 Packing 1020 1480 1100 WEIGHT=290NET (320 GROSS), GBS 242 AutoCut ED.2016 eng rev.00 7140TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE. FITTINGS / OPTIONALS Adjustable bar stop - standard device - Its fixed at the right side; itis suitable to make cuts of the same lenght. Minimal lubrication system - This device, applied to the saw, allows to eliminate almost completely the traditional coolant system, keeps the material much cleaner and avoids to waste cutting oll and water. It works only during the cut. It is comprised of a nozzle - 1/RI0463 - with micro-holes, a tank with devices to adjust the quantity of oil and the air pressure. The switch of the electric system - working with low tension 24V AC - allows to turn it off at any moment and use the normal coolant system 5. MAKE PROPER TOOTH SELECTION For maximum cutting efficiency and lowest cost per cut, it is important to select the blade with the right umber of teeth per inch (TPI) for the material being cut. ‘The material size and shape dictate tooth selection. TOOTH SELECTION - BAND CHOICE In this paragraph we recommend the type of cutting band in accordance with the material to use . To get the best Performance from this machine it's necessary to undestand the right use of the used tools and what you have nct to do with them. The band you have to use must have the following sizes (in mm. ) maximum lenght = 2975 minimum lenght = 2955 total height= 27 _ thickness =0,9 itis also important the material of the band , itis usually used the bimetal band type in the different HARDNESS quality named M42 or SVGLB The endurance of the teeth Increases , and also the fragility, when pass from the material M2 to Mst To making a right cut itis also necessary to choose the pitch ( t) or the number of the teeth per inch (2). Usually the band must have the toothing as follows : ~ close toothing - to cut thin materials, tubular and profiles. = thin toothing- to cut solid materials or pieces that need a long band (for example . the central part ofa profile" U" ‘softer materials as aluminium, copper, soft bronze. By choosing the right one you can avoid a lat of working errors and you can get a good band penetration and the necessary space forthe chips Ifyou cut some pieces at the same time, you must consider them as only one piece by considering the global ‘size, The included table supply you the informations for aright choice, the same one can also be updated or changed by the user according to his personal experiences. Even ifthere are toothings with constant pitch , the most of the band sawing machines allow the use of band wth variable pitch tocthing - groups of teeth with different pitch between them that reduce vibrations and noice, by getting better the finishing and the capacity of removal. GBS 242 AutoCut ED.2016 eng rev.00 13/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE SUGGESTED TOOTH PITCH [SOLID |BIG PROFILES [BUNDLE REF. a PROFILES ‘Wall Lenght Outer | Wall Thickness | to Cut Diamet |Thickness (mm) (mm) er (mm) (mm) VARIABLE CONSTANT 14 M42 = = 5 max |- 10/14 M42 [10 M42 = = 1to2 = 8/12 M42 8 M42 20 max |= 2t04 - 6/10 M42 6 M42 40 max|- 4 to8 = 5/8 or 5/7 5 M42 30to |6to 12 = 50 to 100 4/6 M42 4 M42 50to |10to 20 : 70 to 120 3/4 M42or |3 M42orM51 |80to [15toMAX. |- 100 to MATERIAL ie. DIN | DIN N°] Maximum | Minimum] MOTOR | FEED /COO GROUP | denomination BLADE |BLADESP| SPEED | FORC| L SPEED EED (1or2) | E |ratio m/min_|_m/min 1)STRUCTUR | St37 St42 10037- |60 40 1 LOW [10% AL STEEL 10042 f ‘St50 St60 10050- |50 35 1 Low |10% 10060 HARDENING |C10 C15 10301 [45 35 1 LOW [15% STEEL 10401 i6MnCr5 17131 |40 30 1 Low/ [10% 20CrMo5 17264 Med AUTOMATIC [9520 10SPb28|10711 |70 50 1 LOW | 15% STEEL BEARING | 100Cr6 13505 [50 25 1 Med/ |5% STEEL Hig ‘SPRING 65Si7 15028 |40 30 f Med/ |5% STEEL Hig 4)CAST GG15GG30 |-- 50 30 1 Med/L|dry IRON ow '5)NOT- AL99.5 = 300 50 2 Med/L | 2% FERROUS _|GalSi15Mg ow BRONZE Cusn6é = 120 40 2 Med/ |2% COPPER CuSn6zn 200 50 2 Hig GBS 242 AutoCut ED.2016 eng rev.00 14/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE, ‘You need to consider: The width of the cut - That is, the distance in the eut that each tooth must travel from the point it enters the ‘work-piece nil it eaves the work-piece, and L The shape of the work-piece. © | Squares, Rectangles, Flats (Symbol : Mi) ‘Locate the width of cut on the chart. (inches ‘on the outer circle and millimeters on the inner circle.) Select the tooth pitch on the ring marked with the square shape which aligns with the width of cut. EXAMBLE: 6° (150mm) square, use a 2/3 Vari-Tooth. ‘© Round Solids (Symbol: @) Locate the diameter of your work-piece on the chant. Select the tooth pitch om the ring 6, BLMETAL SPEEDS AND FEEDS These figures are a guide to cutting 4"(100mm) material (orth 2 314 Vari-Tooth) when using a cutting fluid. ‘Increase Band Speed: 15% When catting 1/4" 4mom) material (10/14 Van-Tooth) 12% When cutting mm) material (6/10 Vati-Tooth) 10% When cutting 1-1/4"@2 mm) material(5/8 Vari-Tooth) 5% When cutting 2-1/2" (64 mam) material(4/6 Vari-Tooth) Decrease Band Speed: 12% When cutting 8°(200mm) material(2/3 Vari-Tooth) marked with the round shape which aligns “ALLOY with the size of stock you are cutting. ASTMNO. EXAMPLE: 4" (100mm) round, use 23/4 ‘Vari-Tooth. [Copper [173,932 314 96 © Tubing, Pipe, Steuctural (Symbol : OH Alloy “y 2 330,365 24 a Determine the average width of cut by oad 7 a dividing the area of the work-piece by the 330.260272 577] Te distance the saw blade must travel to finish the cut. Locate the average width of cut on 780,264,632,655 | 248 7 the chart. Select the tooth Ditch on the ring smarked with the tubing and structural shape, for,ro2,110,122,172 | 234 7 oe a ee ee TaLIsn0510; 34 | 7 cutting. EXAMPLE: 4"(100mm) outside diameter, 3°(7Smm) 635,706,715934 | 234 7 inside diameter tubing. 630 oT) 7 £°(00mm) OD =12.5 sqm (79cm) i 3°75 mm) ID = 7.0 sqln (44em") si 24 6 ae Satay eae 39 ~([ 103 1137 288 8 5.5 sq tn, (3Sem")/ 4” (100mzn) iS distance =1.38(35mum) average width meee ae 5 1.38" (35mm), use a 4°6 Vari-Tooth TISTHISTRESS | 279 Pd NOTE: The band speed and cutting rate = eae ee recommendations presented on this chart are [Carbon f00e,i015,1020,1025] "319 7 approximations and are to be used asa — 1035 308 oF starting point for most applications. For exxtsening prarsierd connll yours Tors onto22 | 299 | st blade supplier. GBS 242 AutoCut ED.2016 eng rev.00 15/4010261513 HAlsaes ASGSHAPES) i040] 269 | 82 Staisless [420 1 | 38 Steel 1042, 1541 me | 76 aa aaa |e 1084, 1045 as | 6 ae ee pone pea | Ee a Ts] 35 1095 et | 36 a 5 5 aes weasanosen | 29 | 73 i WE 7a on as 74340,E4540,8630 | 219 | 67 aes case | 8640 199 a 308 ns 35 E9310 3 347 110 3 HeSEL 700 | 30 1 35 416 @ 7 TELLTALE CHIPS hips ave the best indicators of comect feed force. Monitor chip information and adjust feed accordingly. ee ‘Thin or powdered chips ~ increase feed rate or reduce band speed. ‘Bumed heavy chips — reduce feed rate and/or band speed. (StueS ce (Curly silvery and warm chips ~ optimum feed rate and band speed. aa GBS 242 AutoCut ED.2016 eng rev.00 16/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE ‘On some parts of the machine there are come stickers which warn about the safety measures that have to be taken by the operator who runs it. Their meaning (easy to understand) is indicated in the following chart ‘SEGNALI DI AWERTIMENTO E PERICOLO — SAFETY SIGNS ‘SYMBOLES DE SECURITE - SICHERHEITSVORSCHRIFTEN a) == : a be) ete @ : aneeae VoR) coerntatettte 4 — /?—7?7 = Sit aa / “Bost Soe Ati Last oemennect_— PS2T sent herman GBS 242 AutoCut ED.2016 eng rev.00 17/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE ‘These are the references for a manual or Autocut » 2) 3) 4) 5) 8) 7 8) 9) 70) 1) 12) 13) 14) Ges222 BASE WITH DOOR ADJUSTABLE STOP BLOCKS FOR MITRE VICE OPENING HANDLE WORKPIECE LOCKING HANDLE FRONT SLIDING BLADE GUIDE BLADE COVER FIXING KNOB BLADE TENSIONER CONTROL LEVER HANDLE WITH HOLD T FRONT SLIDING BAND GUIDE STOP CONTROL CABINET GEAR AND MOTOR ELECTRIC COOLANT PUMP MITRE CUT HANDLE LEVER FLOOR STAND AND BASE CONNECTING RI0597 AutoCut ED.2016 eng rev.00 band saw machine ~ standard image~ curs ‘0 RUN MICROSWITCH INSIDE, SCREW 19/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE = MACHINE SETTING FOR STARTING Verity that the machine has not clear damages or faults and check upon the standard equipment that includes the toots, fitings to carry out some adjustments, using and maintenance handbook. In case the machine is supplied with adeitional equipment make sure that it is adaptable to the machine. Point in good time the possible damages or faults to the reseller or to the service staff before start-up the machine.- Remove the lock flask between saw frame and base.. The protective sustances put on the surfaces to protect the machine during the moving and transport must be cleaned by a non-filamentous clorth or paper, please check that there Is no rust on the metallic parts ‘Wincase of using compressed alr jet aways wear proper eye protection. Remove the possible ciry that can obstruct the passage of the coolant along the coolant hoses. ‘The patts in motion ( band guides, trolleys, pivots, bearing support, bearing disc ete. ) are already lubricated, the reducer gear holds the exact quantity of oll necessary to the operation because it is a LONG_LIFE construction type. USE OF MAIN MACHINE PARTS 7-LPOWER SYSTEMS AND CONTROL PANEL ‘The electica ating of your band saws with 400 elt phase, magnetic contol Before connecting your machine oan elechical power sytem, be sare the motor shaft is ramsing in the corect Sesion ‘Refer to the electical wiring diagram supplied with {your machine fr instactons ta how to connect saw to power source, Power must be at off when shel cover fs opened o during repaming Pleace check te movin dzection ofthe blade. Ifthe blade is moving in he wrong direcon, please re-connect the wire. RI0598 Operation way = 1. Push the green button(A)(fig.S1) to connect the power for the machine . 2. Fast moving saw-farm to approach cutting material ‘Tum the switch (D(fig S1)) to “Quick” push the handle of limit switch(A)(fiz S2),t cam move the saw farm manually to ‘near the material Ante Cutting ‘Tum the switch (D) (Gel) to “Automatic”, ‘puch the handle of limit switch(A)(fig $2) , The machine will going down and cut by itself Adjust (A) (fig.S3) to set up the down-feed speed im saw-farm 4. Manual Cutting: ‘Tum the switch (D) (fig Sl) to “Manual * , push the handle of limit switeh(A}(fig $2), ‘The machine will convert into the manual cutnng Adjust the spring and (A) (fig.S3) to use manual operation §. Select the blade cutting speed (B) (fig.S1) ! 6. Emergency Stop switch (C) (fg!) : fig S3 ‘The control box include : GBS 242 AutoCut ED.2016 eng rev.00 40‘TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE Main ewitch wit minimum tension coil for undervoltage disconnections- 1/RIO598- -GREEN light (controls of band tensioner, blade protection carter and 24V low tension circuit) -2/R10598- motor speed selector ~3/R10598- ) | -mode selector —/RI0596. wth 3 poston: a) manual cut % ; RIGHTt side. ») autonomous cut with gravity adjustable feed AULOCUE midcle postion ©) impulse lowering for fast approach without cut; LEFT side = hydraulic down-feed reaulator . ~5/R10598- is at the right comer of the base ADJUSTING UPWARD AND DOWNWARD TRAVEL OF SAW ARM ‘The downward travel ofthe saw arm should be adjusted Before swinging the base, make sure there is nothing a. in the way, or any interference. a 1. Unscrew out the knob (A) (fig. 7) swing the saw arm. Xs Refer to scale oa (B) (Gig. 7) for degree. - . 2. Screw out the knob (A) (fig. 7). then start the cutting a 7-S.vise for left and right position Please proceed as follows to obtain desired clamp vise moving to left and right Before moving the vise, make sure there is nothing in the way. or any interference. 1. Unscrew out the knob (A) (fig.7-1) and push the vise 2. The handle willbe left side when the vise stay in left side as(Gig 7-2) 3. And push the handle by anti-clockwise until hear the noise from the vise push the handle ‘Then the handle will be left side (fig.7-3 ) A Fig74 Fig 7-2 Fig 7-3 GBS 242 AutoCut ED.2016 eng rev.00 23/40‘TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE 7-9 REMOVING AND INSTALLING THE BLADE When it is necessary to replace the blade. proceed as follows: |L Raise the saw frame about 6" and close the feed owoff knob by turning it clockwise a fr asi will o (fig 8). 2. Move the blade guide arm to the right. Fig 9). 3. Disconnect the machine from the power source. Loosen cover screw, remove cover (A), open the cover (B), remove cover (C) , then clean the chips and dir inside the machine. 4, Release blade tension (F) (fig 9) by fuming the blade tension hand-wheel counterclockwise. 5, Remove the blade from both wheels and out of each blade guide. But remove side (B) saw blade. When totally released, then remove the side (A). 6. Make sure the teeth of the new blade are pointing in the right direction. TF necessary, tum the blade inside out 7. Place the new blade om the wheels, Inthe blade guides and adjust blade tension and blade guides Fig8 A B Figo CF S.MAINTAINING ‘That's easier to keep machine in good condition or best performance by means of maintaining it at any time than remedy it after it is out of order. (1) Daily Maintenance (by operator) (a) Fill the lubricant before starting machine everyday. (b) Ifthe temperature of spindle caused over-heating or strange noise, stop machine immediately to cheek it fo keeping accurate performance. (©) Keep work area clean; release vise, cuter, work-piece from table; switch off power source; take chip or dus away from machine and follow instructions lubrication or coating rust proof oil before leaving. (2) Weekly Maintenance () Clean and coat the cross leading screw with ol. (b) Check to see if sliding surface and turning pats lack of lubricant. If tile lricant is insufficient, flit. (3) Monthly Maintenance (@) Check if the fixed portion has been loose. (b) Lubricate bearing worm, and worm shaft to avoid the wearing. (4) Yeasly Maintenance (@) Adjust table to horizontal position for maintenance of accuracy. (b) Check electric cord, phugs, switch, at least once and a year to avoid loosening or wearing. GBS 242 AutoCut ED.2016 eng rev.00 24/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE This machine service cooling system ‘The tube was separate. You need to connect it. 1. Assemble the machine stand 2. Assemble the chip-tank (A) (Fig 10) 3. Put the water tank (A) (Fig 10-1 ) into the machine stand 4. Connect the tube( B) (Fig 10-1 ) from the chip-tank (A) (Fig 10 ) to the water tank 3. Screw tight of the tube at the down part of chip tank by the scsew( B) (Fig 10-2 ) ’ = B A’ Fig.102 B 9.1 .Chips clean That is easier to clean the chips by moving the chips tank A (Fig 10 ) Fig.10 A’ ~ BAND RUNNING-IN For granting a better machine efficiency and a longer blade life it is really necessary a good running-in of the machine. For the first works of each band we recommend to reduce the penetration speed of the blade in the workpiece until half of the normal value - about 40 om / min.~ and keep the blade rotation speed constant. Only after cutting 250/350 cm? of the materia it is possible to increase the penetration speed till reaching the normal value. ‘The working conditions can be also valued by considering the chips produced during the cutting, you can find 3 kinds of chips: THIN OR POWDERED CHIPS indicate poor advancing pressure and / or low speed, too ite teeth. = 2 BIG CHIPS - MAYBE BLUE / BROWN indicate overload on the blade, poor lubricating. = b SPIRAL AND RIGHT ENVELOPPED CHIPS indicate the ideal cutting conditions. =< For a right use see the paragraph CHOICE OF THE BAND. - MACHINE RUNNING-IN GBS 242 AutoCut ED.2016 eng rev.00 25/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE, eoTETE Spee Ses Dee z GBS 242 AUTOCUT 2V 3F V400/50 Tet n2GH rep Pee ee ee =I ee TTT ‘| I kl ‘| i —|| GBs 2420 AUTOCUT 2V 3F V400/50 i p3GH Sara Perera se GBS 242 AutoCut ED.2016 eng rev.00 30/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE. NR |BEZEICHNUNG TYP GROSSE sik 7 CAP Screw XCCMFS61025 MIO25 4 2 Washer ‘27002 40x40 25 2 3 Shaft 27008 4 4 [Anchor Block. 27004) 1 5 [C=ring 4 3n Screw z 32 | Sew 3 6 Bearing (ax6205, (6205 2 7 Left Body frame 28507 1 7H PIPE connect 2100764 1 7f2___| PIPE connect for Body frame /30007°2 '50x100%730 1 713 ___| Right Body frame [300073 1 2 Big Waswher [276128 1 13 Load Screw, 27019%4 13 [Washer xcwmwaciestt 1 14 Hox. Sockst Head Screw XCOMWS6525 Mex26t s 18 Fixed Block 27015 2 16 [CAPScrew XCCMWS8B40 Meso 4 7 Bushing 4 18 Reducer Block 30018 4 18 Washer Spring washer MB Ms 4 2 ‘Screw xCMEFEZS Meo 4 2ot__[rut Ms. 4 2 Reducer '30021 1 2 Motor Z7O22/ZUOOSIZEON 1 25 [CAP Sorew XCCMFSSI025 M1025 4 2 Key 2087 ex7x70 ‘i 28 ‘Output Shaft 20028 1 2 Key 20021 7030 4 20 Bearing 27080 6906 2 a ‘Spring Support 30081 1 31/1 | spring holder screw. 270314" s 2 Spring 32147 1 38 Stool Brush 27088) 1 331 [Blade Cover 2008341 1 Ea Brush holder 270832 1 34 ‘Serew Mi6e40 1 241__| Bearing Cover 75081 1 3 ‘Spring Washer 3208211) 2 36 Frame Pivot Shaft 30038 1 38 Screw 2 8 ‘Screw 825 4 39n_[ copper 120806 1 0 Fixed Block 32081 1 a ‘Sat Screw XCCMISEEE Mee 2 2 ‘Switch s1021 VMN-ASS 1 NR |BEZEICHNUNG TP GROSSE STK 3 [Handel fs10226 270431 1 GBS 242 AutoCut ED.2016 eng rev.00 31/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE I nese 20 2aso4a 4 = [Seow Maco 1 = ___|seow XOMBFB MGS 2 Blade adjust sick 30048 4 = [Sew XCMBFSIO M50 2 52 [Blade Cover (Front 27052 #7037 1 33 [Blade Adjust Front) 30053 a 5 [euiae 32084 2 55 | cuide holder 32078 = st |euide 22079 4 56 [screw 4 60 Eccentio Guide 27057 4 et [Bearing ‘ax608() 608 8 2 [Screw XCMBFSIS 5x5 4 3 [CaPsorew XCCMFSS8A0 MBO 3 4 __[ Spring Washer XCWWeOS a 1 65 [Blade Adjustabie (Rear) 30085 4 65 | vane. 210496 2 03 |cAPSerew a G7 | Chip Plate 3006747037, 1 o 2 oy xcwnweos 1 70 XCMOFSIO Ms 1 71 20071 1 72 27002 400.25 1 73 XCMaFIO2S 1 74 1 Tart 2 Ta 2 75 | Blade Back Cover 20075 #7035 1 75H | Blade Left Cover 30075*1#7037 1 75 | blade up cover 30075287037 1 7513 | blade down cover 30075°347035. 1 76 | Wire fed Board 1 Tart [CAPS crow Z 77 [lade Cover pate 285077 er10103 2 77 [lade Coverpiate as077-4 crio108 3 73 |sawstade 0078 296507909 1 72 |iaer wheat 20079 1 [owing xcwpes2s 525 fl 1 | screw XCMBFE20 Mac0 1 52 [Washer XCMMe23 MB X20X3 o 2 [whoet 18075 4 84 [Bearing Cover 27085 1 Bart [Bering 51106, 77086 i108 t @5 [vise Handle 32061 1 NR [BEZeICHNUNG TYP GROSSE sm 85 | Vise Handle Fired Boerd 0086 4 eat |capscrew 3 a: ‘Spring 32033) 4 GBS 242 AutoCult ED.2016 eng rev.00 32/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE 29 [beadecrow 20088 f 90 | Vise Hands Set 0080 3 1 | Vise Handle Rod 0094 1 8th | bearing (0x6904-2RS 6908 4 92 | Leacscrew Copper 30082 4 22 | Leadserow Spxing 0092" 1 ©3__| Moveable Vise Jaw Bracket 30098 1 3671 | Moveable DowmiVio Jaw Bracket Board 300051 2 9372 | set row pes Sao ssaw = | 9314 | set screw (aa 4 | knob 30084 1 25 | Vise Pate 20085 1 35 [sow 2 96 | vise cover 30086 4 96 | screw = 2672 | Spring pin 2 9673 | Nut é 7 | ste 32055 4 8 |Letvise 30088 4 ee [screw XxcM66246-9 1040 4 9672 | sow 2 983 | sew 2 964 [capserew 2 985 | washer 300085 é 9 |Lottvieo Plate 30009 1 100 | Left Cuting Plato ‘20100 1 101 | Fixed Vise Jaw Bracket 30101 1 TO1A [Oring ‘ovoos 44°26 1 roi | serew XOCMWS1025 CAPI0.25 é 10172 | incicator Fixed Board sort? 1 708 | soew 1 102 [Moveable Vise Jaw Brackst Board 30102 161751450 4 02" | serew XQMAB25 825, 3 10272 | washer 4 1028 | caPScrew 2 103 | Bearing 51106 27086 sri06 1 ca 27113 1 104 | asdegree Plato 2ri20cr4 1 ae XCMF1030 1 10572 [nut XoMeA10 3 105A | Base 3010587087 1 1058 [Front door 1 105¢___[cAaPserew 2 NR [BEZEICHNUNG TYP GROSSE STK, 1050 [Washer 3 105E | Serew XOMGF1040 2 105F [Screw 1 1056 | set Nut 4 1054 [Nut 1 GBS 242 AutoCut ED.2016 eng rev.00 33/40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE 25 | Zee Degree Fixed Board 0106 225 4 ransie ‘20600 MBx30_ 1 CAPScrow 4 Washer 4 (CAPSereW 1 Tose [nut 4 107 [Tank 30107#7037, 4 108 | Right Cutting Pate 30108 1 7081 [ screw 6 109 Vise Copper 30109 2019 1 108/5| Vise ton 30109" 20418) 1 410 | knob Nut 27108 4 111 | Screw 6°20 4 112 | stop Braket 27107 4 119 | Rod stock stop 27106 1 114 [Right Vie sori 1 115 [knob 320504 gi 116 | Plato 30116 1 Tet | Screw 1 117 [Right View Plate 0117 a 718 | witor Plate 0118 1 1181 [scww 2 1182 [oilHead ‘SU005 tox1.0 4 1188 [nut 2 184 [Nut 1 71865 | sorew 1 110 | Breaking Elstonio Board 0118 1 tia [cascrew 1 720 | Nut 2118 1 122 Ani-Chip Cover 27037 il 123 | bushing anit 4 724 | Bearing 32008 0x3 2008, 2 425 | eyinder support 30126 1 1258 | Spring holder 12060 1 4258 | Spxing support 21186. a 125 [Washer XCMMe233 87253 1 1251 [screw XOCMWS6825 CAP 8°25 4 1252 [screw XCCMWS1065 CAP 10x65 1 1254 [Pin XCWMWCGE30 630 2 1256 [Nut 1 1256 | screw 1 NR [BEZEICHNUNG TP (GROSSE STK 125 | olinder 30128 il 126A | eyinder support plate 301268 1 127 [oithouse suppot pate 30127 1 127 [screw 1 128 | Eletronic control suppote 30128 1 128 [screw 4 GBS 242 AutoCut ED.2016 eng rev.00 34/40‘TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE 1282 __|CAPScrew 2 120 ‘Swivel table. 30129 1 1201 | Angle stick ud 130 Main shaft 30130 H 134 Bearing 32006. .9x32006 32006 i 133 ‘Switch cover, 28520087035, 1 132 ‘Switch Base. 285200°1 #7035 a 134 PUMP 10013 iu 1344 [crow z 1348 | L-copper 271361G. 1 138 Tank 30136 iu 137 House 30137 iJ 137A | Tube Bundle hs 1056 1048 \ 104A GBS 242 AutoCut ED.2016 eng rev.00 105H 1056 a 35/40‘TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE (GBS 242 AuioCut ED.2016 ng f0v.00 3640“TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE GDS 242 AuioCut ED.2016 ng rev.00 3e40TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE. (GBS 242 AutoCt ED.2016 eng rov.00 3940 1/3 ae ) Se aTRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE GBS 242 AntoCu ED.2016 eng rev.00 4040