Scribd
Upload
98 views1 page

CTS Sentinel I28 Installation Guide

1. The document provides installation and mounting data for an I28 device, including port locations for supply vacuum, supply air, pilot air, and power entry. 2. Key dimensions are provided such as overall height, width, depth, and locations of mounting holes and ports. 3. The device has four rear mounting holes for attachment to a mounting plate with a minimum thickness of 1/4 inch.

Uploaded by

Carsen Appel
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
98 views1 page

CTS Sentinel I28 Installation Guide

1. The document provides installation and mounting data for an I28 device, including port locations for supply vacuum, supply air, pilot air, and power entry. 2. Key dimensions are provided such as overall height, width, depth, and locations of mounting holes and ports. 3. The device has four rear mounting holes for attachment to a mounting plate with a minimum thickness of 1/4 inch.

Uploaded by

Carsen Appel
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Table Of Contents

8 7 6 5 4 3 2 1

I28 INSTALLATION AND D


D
MOUNTING DATA
1/4 NPT PORT
FOR SUPPLY VACUUM
"PLUG IT WHEN USING A SINGLE SOURCE"

1/4 NPT PORT 1/8 NPT PORT


FOR SUPPLY AIR FOR PILOT AIR
POWER ENTRY 3 PRONG [545.05]
STANDARD WITH 120 VAC, 21.46
C 3 CONDUCTOR CABLE FOR 305.57 C
APPROX. WITH LID OPEN
ALL OTHERS 12.030
257.64
220.61 10.143 Hanging Hole
RS232 SERIAL PORT Mounting Holes For 1/4 Inch SHCS
8.685
128.82
I/O FUSE HOLDER-1A 5.07
ETHERNET
ELECTRONIC MODULE,AC-I28)

3.341

235.59
9.275
I/O CONNECTOR

B 115.63 B
299.15
4.552
11.777
Mounting Holes

FOUR (4) REAR MOUNTING HOLES FOR


1/4" SOCKET HEAD CAP SCREW OR
6 MM SOCKET HEAD CAP SCREW BY 3 1/2 INCH LONG
(1/4 INCH MINIMUM MOUNTING PLATE THICKNESS)
TEST PORT
ALLOW 4 IN (101.6 MM) CLEARANCE FOR
SELF TEST CAP SELF TEST CAP INSTALLATION OF TEST LINE AND HAND
AND HOLDER CLEARANCE
DESCRIPTION: UNLESS OTHERWISE SPECIFIED
A Base Assembly BREAK ALL SHARP CORNERS A
MATERIAL: 5555 DRY FORK RD. CLEVES, OH 45002
TOLERANCES:

SolidWorks
CUSTOMER
1 PLACE DECIMAL .050" [1.27mm]
FINISH: 2 PLACE DECIMAL
3 PLACE DECIMAL
.010" [0.25mm]
.003" [0.08mm] CTS R&D
- ANGLULAR DIMS 0 30' TITLE
QUANTITY: HEAT TREAT: 125
INDICATES
500 MAXIMUM FINISH REQ'D ON
Assy,CTS,A12-547
SURFACES WITHOUT A SYMBOL

Wednesday, January 18, 2012


DRAWN BY SIZE DATE DWG NO. REV
FILE LOCATION:
DRILLED AND COUNTERBORED
YA D 10/28/2011 A12-547 A
CHECKED BY
HOLE DIAMETERS:
-.005" / +.015" [-0.13mm / +0.4mm] SCALE
1:4 SHEET 1 OF 3

8 7 6 5 4 3 2 1 2 of 68

You might also like