N1602-1 Alternator / N3118 Regulator
C. E. Niehoff & Co. OEM Wiring Connections
BRUSHLESS ALTERNATORS Dual or Single Voltage
Installation Instructions
DUAL VOLTAGE (28 V/14 V) applications
(see other side for single voltage):
1. Connect as shown on this page. Boots (2)
➛
Locknut, #10-24;
➛
➛
torque to 2.3 Nm / 20 lb.in. Locknut, 0.2500-20;
Washer
➛ ➛
➛ torque to 4 Nm / 35 lb.in.
➛ Washer
Regulator - AC terminal ➛ Regulator - IGN terminal
➛
Regulator
➛
➛
Boot
➛
➛ connectors
Vehicle
➛
harness Regulator - 14 V terminal
Washer
Nut, 0.3125-18 UNC-2B;
torque to 5.6 Nm / 50 lb.in.
Figure 1- N1602-1 Alternator Figure 1a - N3118 Regulator Wiring Connections
B+ connections on alternator
Bolt, 0.3750-16 UNC-2A; torque to 20 Nm / 15 lb.ft. when securing B+ cables. Both positive
cables must be connected together at battery positive potential when alternator is installed
in vehicle and during operation. Interconnect cable is part of vehicle cabling.
➛ ➛
Interconnect Lockwasher
Lockwasher ➛ cable
➛
➛ Washer
Washer
➛ ➛
Positive cable from vehicle
Positive cable
➛
from vehicle ➛ Secure alternator mounting
lug to vehicle using hard-
➛
ware specified by vehicle
➛
➛
manufacturer and torque
B– connections on alternator
B+ output terminals sufficient to withstand weight
Bolt, 0.3125-18 UNC-2A; torque to 9
➛
of alternator.
Nm / 80 lb. in. when securing B–
cables. Both ground cables must be
➛
MS21245-L12 nut;
connected to vehicle’s common ➛ torque to 163 Nm/
ground when alternator is installed in 120 lb. ft. when
➛
vehicle and during installing drive pulley.
operation.
Washer
Lock Washer Secure alternator mounting
➛
lugs to vehicle using hard-
Washer
➛
➛ ➛ ➛ ware specified by vehicle
manufacturer and torque
➛
Vehicle
harness sufficient to withstand weight
of alternator.
Figure 1b - B+ and B– Terminal Connections
Page 1 of 2 II0059A
SINGLE VOLTAGE (28 V) applications
(see other side for dual voltage):
1. Connect as shown on this page. Boots (2)
➛
Locknut, #10-24;
➛
➛
torque to 2.3 Nm / 20 lb.in. Locknut, 0.2500-20;
Washer
➛ ➛
➛ torque to 4 Nm / 35 lb.in.
➛ Washer
Regulator - AC terminal ➛ Regulator - IGN terminal
➛
Regulator
➛
➛
➛
➛ connectors
➛
Washer Regulator - 14 V terminal
Nut, 0.3125-18 UNC-2B;
torque to 5.6 Nm / 50 lb.in.
Figure 2- N1602-1 Alternator Figure 2a - N3118 Regulator Wiring Connections
B+ connections on alternator
Bolt, 0.3750-16 UNC-2A; torque to 20 Nm / 15 lb.ft. when securing B+ cables. Both positive
cables must be connected together at battery positive potential when alternator is installed
in vehicle and during operation. Interconnect cable is part of vehicle cabling.
➛ ➛
Interconnect Lockwasher
Lockwasher ➛ cable
➛
➛ Washer
Washer
➛ ➛
Positive cable from vehicle
Positive cable
➛
from vehicle ➛ Secure alternator mounting
lug to vehicle using hard-
➛
ware specified by vehicle
➛
➛
manufacturer and torque
B– connections on alternator
B+ output terminals sufficient to withstand weight
Bolt, 0.3125-18 UNC-2A; torque to 9
➛
of alternator.
Nm / 80 lb. in. when securing B–
cables. Both ground cables must be
➛
MS21245-L12 nut;
connected to vehicle’s common ➛ torque to 163 Nm/
ground when alternator is installed in 120 lb. ft. when
➛
vehicle and during installing drive pulley.
operation.
Washer
Lock Washer Secure alternator mounting
➛
lugs to vehicle using hard-
Washer
➛
➛ ➛ ➛ ware specified by vehicle
manufacturer and torque
➛
Vehicle
harness sufficient to withstand weight
of alternator.
Figure 2b - B+ and B– Terminal Connections
C. E. Niehoff & Co. • 2021 Lee Street • Evanston, IL 60202 Tech Services Hotline 800-643-4633
Page 2 of 2 II0059A
