User Manual

Lambda Transmitter LT2

Lambda Probe LS2

Sensors and Systems for Combustion Engineering www.lamtec.de

 Table of Contents

Table of Contents

1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Validity of these Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 6
2.1 Explanation of the Symbols in the Safety Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 6
2.2 Proper Use - Conditions of Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 7
2.3 Permissible Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 8
2.4 Safety Equipment/Safety Measures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 9
2.5 Protection Against Emissions from Gas Carrying Channels . . . . . . . . . . . . . . . . . . . . .. 9
2.6 Important Notes on Shutdown/Return to Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.7 Environmental Protection, Waste Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1 System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2 Brief Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1 System Overview - Necessary Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1.1 Advantages of the Measurement Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.2 LT2 Lambda Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.2.1 LT2 Lambda Transmitter in Wall Mounting Case . . . . . . . . . . . . . . . . . . . . . . . . 15
4.2.2 Probe Connection Box (PCB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.3 Cold-start Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.4 Device Configuration and Factory Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.5 Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.5.1 Display and Operating Unit Type 657R0831 . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.5.2 Remote Display Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.5.3 Calculation of Combustion Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.5.4 Calculation of the CO2 Concentration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.5.5 Firing Rate Dependent and Fuel Specific Limit Values/Limit Curves. . . . . . . . . 27
4.5.6 Draught Measurement (Available on Request) Type 657R0110 . . . . . . . . . . . . 27
4.5.7 1 ... 4 Analogue Output (0/4 ... 20 mA, 1 ... 10 V) . . . . . . . . . . . . . . . . . . . . . . . 27
4.5.8 Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.5.9 1 ... 4 Analogue Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.5.10 BUS interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5 LAMTEC SYSTEM BUS (LSB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.1 Jumpers, LED, Fuses and Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.2 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.3 Wiring Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6 Commissioning/Decommissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.1 Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.1.1 Device Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.2 Preliminary Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.2.1 The LT2 Lambda Transmitter's Display and Operating Elements . . . . . . . . . . . 34
6.2.2 Monitor Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.2.3 Internal Display and Operating Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.3 Measurement Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.3.1 Install the Probe in the PIF and Align the GED . . . . . . . . . . . . . . . . . . . . . . . . . 38

2
Table of Contents

6.4 Setting up Service Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

6.5 Decommissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

7 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7.1 Operation/Measurement Value Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7.1.1 Measurement Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7.1.2 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.1.3 Status Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.1.4 Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.2 General Instructions for Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
7.2.1 Measurement During Distinct Pressure Surges at the Measuring Site . . . . . . . 42
7.2.2 Operational Failure, Switching On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
7.2.3 Liquid Purification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

8 Service and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

8.1 Checking the O2 Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
8.1.1 Checking the Air Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
8.1.2 Checking by Counter Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.2 Checking the LT2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
8.2.1 Checking the LT2's Measuring Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
8.2.2 Checking the Probe's Internal Resistance Measurement . . . . . . . . . . . . . . . . . 46
8.3 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
8.3.1 Consumable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

9 Faults/Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
9.1 Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
9.2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.3 Resetting Faults/Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
9.3.1 Faults - Causes and Solutions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
9.3.1.1 Probe voltage too low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
9.3.1.2 Defective LS2 Probe Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
9.3.1.3 Broken Wire Probe/Defective Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
9.3.1.4 No Probe Dynamics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
9.3.1.5 Fault Analogue Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
9.3.1.6 O2 Value Is Incorrect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
9.4 Warnings - Causes and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
9.4.1 LS2 Internal Resistance too High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
9.4.2 Offset Voltage to Air Invalid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
9.4.3 Analogue Inputs 1/2/3/4 Input Value too Large/too Small . . . . . . . . . . . . . . . . . 53
9.4.4 Configuration Error at Analogue Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
9.4.5 Service Warning 1/Service Warning 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

10 Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

11 Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
11.1 Technical Data LT2 Lambda Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
11.1.1 Technical Data LT2 in Wall Mounting Housing. . . . . . . . . . . . . . . . . . . . . . . . . . 55
11.2 Technical Data LS2 Lambda Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
11.3 Technical Data LS2-HT Lambda Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
11.3.1 Terminal Assignment terminal socket for Probe HT. . . . . . . . . . . . . . . . . . . . . . 65
11.4 Electric Connections Device Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

3
Table of Contents

11.4.1 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
11.4.2 DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
11.4.3 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
11.4.4 LT2 Power Electronic Type 657E1882. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
11.5 Wet/Dry Measurement Deviations, Conversion Table . . . . . . . . . . . . . . . . . . . . . . . . . . 68

12 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

4
 1 General Information

1 General Information
1.1 Validity of these Instructions

Content of this Operating Manual

This Operating Manual describes the Lambda Transmitter LT2 with all components necessary
for O2 measurement, such as the Lambda Probe LS2, the probe installation fitting, etc.

Accessories and special applications

Information on accessories and special applications is provided in the booklets supplied with
the particular systems. This information can be obtained from the manufacturers, at the Wall-
dorf address.
This Operating Manual explains the functioning, mounting, installation, maintenance and op-
eration of the Lambda Transmitter LT2. Other booklets, such as Product Information for exam-
ple, provide further information but must never be used as a substitute for this Operating
Manual.

CAUTION!
Always read the Operating Manual before starting work!
Please adhere strictly to all warnings/safety instructions!

For particular tasks, for example electrical installation, specialised knowledge is required.
These tasks may only be carried out by suitably qualified personnel. See chapter 2.3 Permis-
sible Users.

Validity
Our products undergo constant redevelopment. However, we make every effort to ensure that
the Operating Manual is accurate and relevant to individual applications.
All previous editions are rendered obsolete on publication of an updated and corrected new
edition.
On the last page you will find the current version number of this Operating Manual and the
corresponding order number.

5
 2 Safety

2 Safety
2.1 Explanation of the Symbols in the Safety Notes

The following symbols are used in this document to draw the user's attention to important safe-
ty information. They are located at points where the information is required. It is essential that
the safety information is observed and followed, and that applies particularly to the warnings.

DANGER!
This draws the user's attention to imminent danger. If it is not avoided, it will result in death or
very serious injury. The plant including its surroundings could be damaged.

WARNING!
This draws the user's attention to the possibility of imminent danger. If it is not avoided, it may
result in death or very serious injury. The plant including its surroundings could be damaged.

CAUTION!
This draws the user's attention to the possibility of imminent danger. If it is not avoided, it may
result in minor injuries. The plant including its surroundings could be damaged.

NOTICE
This draws the user's attention to important additional information about the system or system
components and offers further tips.

The safety information described above is incorporated into the instructions.

Thus, the operator is requested to:
1 Comply with the accident prevention regulations whenever work is being carried out.
2 Do everything possible within his control to prevent personal injury and damage to prop-
erty.

6
 2 Safety

2.2 Proper Use - Conditions of Use

Application
The LT2 Lambda Transmitter is an O2 measuring instrument for the continuous measurement
of O2 concentration in non-combustible gases in the super-stoichiometric domain, in conjunc-
tion with the LS2 Lambda Probe.
Suitable for gas measurements with a small proportion of combustible components
(< 10,000 ppm), for example in flue gases of combustions systems.
Admissible fuels:
• Non-interacting gaseous hydrocarbons
• Light oil
• Coal
• Biomass (wood)

NOTICE
Direct measurements in combustion gases are not possible.

If the system is to be used in some other way, and if the instrument's functionality in this ap-
plication cannot be unambiguously assessed, the manufacturer should be contacted in ad-
vance.
Prerequisites
It is assumed that facility planning, assembly, installation, commissioning, maintenance and
service works are carried out by sufficiently trained personnel, and these works are supervised
by qualified specialists.
Correct handling
Special attention must be paid to the following:
– The application must conform to the technical data and the specifications regarding au-
thorised use, assembly, connection, environmental and operational conditions (derived
from the job documentation, the instrument's user information, rating plates etc), and to
the documentation supplied.
– The local regulations and facility-specific and technical hazards must be noted and fol-
lowed.
– All steps necessary to protect the equipment, e.g. during transport, storage, maintenance
and inspection, should be carried out.

7
 2 Safety

2.3 Permissible Users

Qualified personnel
The person responsible for safety absolutely must guarantee that
• only qualified personnel perform work on the system parts.
Due to their training, education, experience, or instruction and due to their knowledge of
pertinent standards, provisions, accident prevention regulations, and system conditions,
qualified personnel are authorized to perform these tasks by the person responsible for
the safety of people and the system. It is decisive that this personnel must be able to rec-
ognise and prevent risks on time.
Experts are considered to be people according to DIN VDE 0105 or IEC 364 or directly
comparable standards like DIN 0832.
• These persons must have access to the provided operating manual and any pertinent or-
der-related documentation during all work and observe these documents within the scope
of preventing risks and damage.

User groups
For the handling of the Lambda Transmitter LT2, three user groups are required:
• Service technicians of LAMTEC or its OEM customers and/or trained customer personnel:
– Qualified technicians/engineers  have very good knowledge of the device.
– SERVICE access level - password-protected
• Operators, customer fitters, technicians for instrumentation and control technology, elec-
tricians, and electronic engineers  have introductory knowledge of the device.
– CUSTOMER access level - password-protected
• Operating personnel with basic knowledge
– OPERATION access level - no password

8
 2 Safety

2.4 Safety Equipment/Safety Measures

Hazards from electrical equipment

The LT2 and the Lambda Transmitter Lambda Probe is equipment for use in industrial electri-
cal power installations. Always switch off the power when working on mains connections or
mains voltage. If contact protection has been removed, reattach it before switching on the
power supply again. Damage to health or equipment may result from improper use or improp-
er handling.

NOTICE
To avoid damage, always observe the respective security notices.

Preventive measures for improving operating safety

If the LT2 is used in conjunction with control and steering technology, the operator must ensure
that any breakdown or failure of the LT2 device does not cause inadmissible damage or dan-
gerous operating states. To avoid faults which could cause direct or indirect personal or ma-
terial damage, the operator must ensure that:
• the responsible maintenance personnel can be reached at any time and as quickly as pos-
sible
• the maintenance personnel are trained to correctly respond to faults with the LT2 Lambda
Transmitter and the associated malfunctions
• in the case of doubt, the faulty equipment can be switched off immediately
• A switch-off does not lead to direct follow-up problems.
Avoiding consequential damages
To avoid consequential damages in the event of failure, which could cause direct or indirect
personal or material damage, the owner must ensure that qualified personnel can assess the
faults and initiate appropriate measures to tackle them.

2.5 Protection Against Emissions from Gas Carrying Channels

The Lambda Transmitter LT2 is attached directly to the gas-carrying duct by the probe instal-
lation fitting (PIF) and the mating flange. If the LS2Lambda Probe or the probe installation fit-
ting (PIF) is removed, the operating system, especially if pressurised, can cause corrosive
and/or hot gas to escape from the duct through the flange, causing severe injury to the oper-
ator if the operator is unprotected and if appropriate safety precautions have not first been tak-
en.

WARNING!
Discharge of hot, corrosive gases!
With pressurised gas, corrosive gases and/or temperatures higher than 200 °C in the gas-car-
rying duct, gases can escape if the Lambda Probe LS2 or the probe installation fitting (PIF) is
removed
 Before opening, switch off the installation. If this is not possible, put on protective clothing
and masks
 Place appropriate warning signs in the vicinity of the unit
 Reseal the opening immediately. Appropriate sealing flanges (blind flanges) are available
as accessories

9
 2 Safety

2.6 Important Notes on Shutdown/Return to Service

The Lambda Transmitter and the Lambda Probe form a high quality electronic system. Treat
them with care at all times, including during shut-down, transport and storage.

Shut-down

NOTICE
Do not switch the Lambda Transmitter off as long as the Lambda Probe is mounted; including
when the relevant facility has been shut down. Residual gases cause corrosion and may dam-
age system parts.
 Do not store the instruments outdoors without protection!
Always store in a dry place, if possible in the original packaging.
 When dismantling, protect cable ends and plugs against corrosion and dirt. Corroded
plugs may cause malfunction.
 If possible, transport in the original packaging.

WARNING!
Danger of burns!
Probe becomes hot during operation.
If the probe is operated when removed, there is a danger of burns on the probe housing.
 Never lay the probe on flammable material and heat it up.
 Wear protective gloves

Return to service
According to chapter 6 Commissioning/Decommissioning.

2.7 Environmental Protection, Waste Disposal

The design of Lambda Transmitter and LS2 is also based on environmental considerations.
The modules can easily be separated and sorted into distinct types, and recycled accordingly.

10
 3 Overview

3 Overview
3.1 System Overview

The LT2 Lambda Transmitter is an all-purpose O2 measuring device based on microprocessor

for direct measurement of the O2 concentration under super-stoichiometric range (λ > 1) used
together with LS2 Lambda Probe.
For compilation of combustible gas components (CO/H2), the optional combination probe KS1
can be used.

Fig. 3-1 System overview LT2 Lambda Transmitter

11
3 Overview

Fig. 3-2 System overview - LT2 Lambda Transmitter input/output modules

12
 3 Overview

3.2 Brief Description

Universal O2 measuring instrument, based on the LS2 Lambda Probe (zirconium dioxide volt-
age probe), for the direct continuous measurement and monitoring of oil (EL) and gas com-
bustion systems in the super-stoichiometric domain ( > 1)without special gas purification.

Fig. 3-3 LT2 Lambda Transmitter wall-mounting housing IP65

400x300x150 mm (HxWxD) type 657R102-...

Fig. 3-4 LS2 Lambda Probe, type 650R1000 with gas extraction device (GED) type 655R1001 - R1003
and probe installation fitting (PIF) type 655R1010

13
 4 Technical Description

4 Technical Description
4.1 System Overview - Necessary Components

The O2 measurement system is available in various versions. It consists of the following com-
ponents:
– LS2/LS2-HT Lambda Probe
– Gas extraction device (GED)/flue gas bypass tube
– Probe installation fitting (PIF)/counterflange
– Probe connection box (PCB)
– LT2 Lambda Transmitter in IP65 wall-mounted housing

4.1.1 Advantages of the Measurement Principle

• No gas treatment needed, measurement directly in the humid flue gas

• Setting time at 90 %-value (T90) < 20 s
• Measuring gas temperature depending on the design up to 300 °C (572 °F)/up to 1200 °C
(2192 °F)
• Low heating power 15 ... 25 W
depending on the state of aging of the zirconium dioxide sensor
• Universal applicable
• Easy application
• Low-maintenance

14
 4 Technical Description

4.2 LT2 Lambda Transmitter

4.2.1 LT2 Lambda Transmitter in Wall Mounting Case

1 Display and operating unit

2 Probe and electronics trans-
former
3 Connection for Remote-Display-
Software (Option)
4 Connecting cable with plug for
display and operating unit
5 Electrical connections
6 BUS-interface alternative
LAMTEC SYSTEM BUS
(CAN BUS)
7 Operating mode display
multifunction push button
maintenance switch
8 Protective earth terminal for
cable screening
9 Monitor output
10 Mains connection (plug)
11 Terminal bar x 2
12 Relay module type 660R0017

Fig. 4-1 LT2 Lambda Transmitter in wall-mounting housing type 657R1025 with dis-
play and operating unit type 657R0831

Accessible after removing the front panel with the main

switch (POWER)
Fig. 4-2 Change over power supply voltage

NOTICE
Fuse replacement F1/F3 when changeover 230/115 VAC necessary !

15
 4 Technical Description

4.2.2 Probe Connection Box (PCB)

For use at large distances (> 2 m/6.562 ft) between probe and analyser, where no customised
cable is employed.
Input: Probe plug
Output: Terminal strip
The PCB contains a terminal strip and conversion to the probe and heating plugs.

Fig. 4-3 PCB-Dimension diagram high: 55 mm (2.166" in) protection class: IP54 Fig. 4-4 PCB-Connection diagram
33 Probe signal -
34 Probe signal +
35 Probe heater
36 Probe heater

16
 4 Technical Description

4.3 Cold-start Delay

Serves to suppress false measurements while the probe warms up to operating temperature.
Cold-start delay is always activated after POWER OFF and probe replacement.
The cold-start delay can be aborted at any time
• via the multifunction key
• via the optional display and operating unit, see separate publication
• via Remote-Display-Software, see separate publication
During the cold-start delay, either
• a substitute value (factory setting), O2 0 % vol. (P361)
• set the type of the substitute value for O2 in P362:
OFF: No output of the substitute value
ON: Output of the substitute value of the preceding parameter.
+Maintenance: (factory setting): Output of the substitute value of the preceding parameter,
even in maintenance mode.
+Maint.freeze: Output of the substitute value of the preceding parameter in the case of cold
start or error as hitherto. Additionally the preceding measurement value is freezed, as long as
maintenance mode is active.
The substitute value during cold start/error takes priority over the freezing of the measurement
value during maintenance.frozen
After a pre-heating period of 10 minutes the probe voltage stabilises to a value between
0 ... 20 mV and the AC inner resistance to a value below 100 .

17
 4 Technical Description

4.4 Device Configuration and Factory Setting

You can derive the device's variant from the variant number. You will find the variant number
on the type plate. The variant number is constructed according to the following key:

Serial Number
Example: LT2 in variant No.:
LS2 1S a1 b0 c11 c21 c31 c40 d15 d25 d30 d40 e00 f4 g1 i0 k0 m1 n0 oE z0
LT2: LS2 1S a1 b0 c11 c21 c31 c40 d15 d25 d30 d40 e00 f4 g1 i0 k0 m1 n0 oE z0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

1: for probe
KS1  configured for CO probe KS1
KS1D  configured for Combination Probe KS1D
LS2  configured for Lambda Probe LS2

2: Type
1S  standard type
2OEM  OEM type
3a  for probe with bypass and purge unit
3K  for probe type ’K - semi automatic calibration’
3KR  for probe type ’KR - cyclic regeneration’
4KA  for probe type ’KA - semi automatic calibration and purge’
5KV  for probe type ’KV - full automatic calibration’
6KVA  for probe type ’KVA - full automatic calibration and purge’
6KVZ  for probe type ’KV-full automatic calibration and regeneration cyclic’
7EX1  for probe type ’EX-area 1’
8EX2  for probe type ’EX-area 2’
9E  for probe type ’HT - ejector extraction’

3: Display
a0  without
a1  with display and operating unit 657R0831/33
a2  with display and operating unit 657R0833RBT

18
4 Technical Description

4: Pressure sensor
b1  with absolute pressure and differential pressure
b2  with differential pressure sensor
b3  with pressure sensor for draught measurement

5: Analogue output 1
c11  analogue output 1 current 4 ... 20 mA 657R0050
c12  analogue output 1 current 0 ... 20 mA 657R0050
c13  analogue output 1 voltage 0 ... 10 V 657R0050
c14  analogue output 1 current 4 ... 20 mA floating 657R0054
c15  analogue output 1 current 4 ... 20 mA floating 657R0054REG
c16  analogue output 1 current 0 ... 20 mA floating 657R0054
c17  analogue output 1 voltage 0 ... 10 V floating 657R0054
c18  analogue output 1 ejector control 657R0050E
c19  analogue output 1 current 4 ... 20 mA electrically isolated 657R0053

6: Analogue output 2
c21  analogue output 2 current 4 ... 20 mA 657R0050
c22  analogue output 2 current 0 ... 20 mA 657R0050
c23  analogue output 2 voltage 0 ... 10 V 657R0050
c24  analogue output 2 current 4 ... 20 mA floating 657R0051
c25  analogue output 2 current 4 ... 20 mA floating 657R0051REG
c26  analogue output 2 current 0 ... 20 mA floating 657R0051
c27  analogue output 2 voltage 0 ... 10 V floating 657R0051
c28  analogue output 2 ejector control 657R0050E
c29  analogue output 2 current 4 ... 20 mA electrically isolated 657R0053

7: Analogue output 3
c31  analogue output 3 current 4 ... 20 mA 657R0050
c32  analogue output 3 current 0 ... 20 mA 657R0050
c33  analogue output 3 voltage 0 ... 10 V 657R0050
c34  analogue output 3 current 4 ... 20 mA floating 657R0051
c35  analogue output 3 current 4 ... 20 mA floating 657R0051REG
c36  analogue output 3 current 0 ... 20 mA floating 657R0051
c37  analogue output 3 voltage 0 ... 10 V floating 657R0051
c38  analogue output 3 ejector control 657R0050E
c39  analogue output 3 current 4 ... 20 mA electrically isolated 657R0053

19
4 Technical Description

8: Analogue output 4
c41  analogue output 4 current 4 ... 20 mA 657R0050
c42  analogue output 4 current 0 ... 20 mA 657R0050
c43  analogue output 4 voltage 0 ... 10 V 657R0050
c44  analogue output 4 current 4 ... 20 mA floating 657R0051
c45  analogue output 4 current 4 ... 20 mA floating 657R0051REG
c46  analogue output 4 current 0 ... 20 mA floating 657R0051
c47  analogue output 4 voltage 0 ... 10 V floating 657R0051
c48  analogue output 4 ejector control 657R0050E
c49  analogue output 4 current 4 ... 20 mA electrically isolated 657R0053

9: Analogue input 1
d11  analogue input 1 potentiometer 1...5 k
d12  analogue input 1 current 0/4 ... 20 mA passive
d13  analogue input 1 voltage 0 ... 2900 mV (EX1)
d14  analogue input 1 pulse (RPM)
d15  analogue input 1 temperature Pt100 0 ... 320 °C (32 ... 608 °F)
d16  analogue input 1 temperature Pt100 0 ... 850 °C (32 ... 1562 °F)
d17  analogue input 1 current 0/4 ... 20 mA active (24 V supply)
d18  analogue input 1 differential pressure
d19  analogue input 1 voltage -100 ... 2000 mV (KS1D)

10: Analogue input 2

d21  analogue input 2 potentiometer 1 ... 5 k
d22  analogue input 2 current 0/4 ... 20 mA passive
d23  analogue input 2 voltage 0 ... 2900 mV (EX1)
d24  analogue input 2 pulse (RPM)
d25  analogue input 2 temperature Pt100 0 ... 320 °C (32 ... 608 °F)
d26  analogue input 2 temperature Pt100 0 ... 850 °C (32 ... 1562 °F)
d27  analogue input 2 current 0/4 ... 20 mA active (24 V supply)
d28  analogue input 2 absolute pressure
d29  analogue input 2 voltage 0 ... 10 V

11: Analogue input 3

d31  analogue input 3 potentiometer 1 ... 5 k
d32  analogue input 3 current 0/4 ... 20 mA passive
d33  analogue input 3 voltage 0 ... 2900 mV EX1
d34  analogue input 3 pulse (RPM)
d35  analogue input 3 temperature Pt100 0 ... 320 °C (32 ... 1562 °F)
d36  analogue input 3 temperature Pt100 0 ... 850 °C (32 ... 1562 °F)
d37  analogue input 3 current 0/4 ... 20 mA active (24 V supply)
d38  analogue input 3 differential pressure
d39  analogue input 3 voltage 0 ... 10 V

20
4 Technical Description

12: Analogue input 4

d41  analogue input 4 potentiometer 1 ... 5 k
d42  analogue input 4 current 0/4 ... 20 mA passive
d43  analogue input 4 voltage 0 ... 2900 mV EX1
d44  analogue input 4 pulse (RPM)
d45  analogue input 4 temperature Pt100 0 ... 320 °C (32 ... 608 °F)
d46  analogue input 4 temperature Pt100 0 ... 850 °C (32 ... 1562 °F)
d47  analogue input 4current 0/4 ... 20 mA active (24 V supply)
d48  analogue input 4 absolute pressure
d49  analogue input 4 voltage 0 ... 10 V

13: RM/LI/Controller/Firing Rate

e30  relay module 657R0857
e31  firing rate dep. limit values, firing rate def. LSB and relay module 657R0922
e32  firing rate dep. limit values, firing rate def. poti and relay module
657R0922/PO
e33  firing rate dep. limit values, firing rate def. current. and relay module
657R0922/ST
e34  O2-controller (PID), firing rate def. LSB and relay module 657R1120
e35  O2-controller PID, firing rate def. poti and relay module 657R1120/PO
e36  O2-controller PID, firing rate def. current. and relay module 657R1120/ST
e37  speed dependent O2 controller, firing rate def. LSB and relay module
657R1123
e38  speed depended O2 controller, firing rate def. LSB and relay module
657R1123/PO
e39  speed dependent O2 controller, firing rate def. current and relay module
657R1123/ST
e40  output of burner-firing rate at analogue output 657R1124

14: Efficiency calculation

f1  efficiency calculation (fixed ambient temperature) 657R0896
f2  efficiency calculation 657R0895
f3  temperature measurement 0 ... 320 °C/ 850 °C (32 °F ... 606 °F/1562 °F)
f4  efficiency calculation incl. 2x Pt100 sensors and analogue output
657R0917
f5  Efficiency calculation incl. 2x Pt100 sensors 699R0895
f6  Efficiency calculation incl. 1x Pt100 sensors 699R0896

15: Supply voltage

g1  supply voltage 230 VAC
g2  supply voltage 115 VAC

16: Reference air pump

i1  pump unit for reference air 230 VAC 657R1060
i3  pump unit for reference air 115 VAC 657R1060

21
4 Technical Description

17: Case heating

k1  housing heating 230 VAC/120 W 657R0367

18: CO monitoring/controlling
m1  CO controller master 657R0602
m2  CO controller slave 657R0602 & 663R1030
m3  CO monitoring master 657R0601
m4  CO monitoring slave 657R0601

19: Calculations
n1  CO2 calculation 657R0910
n2  O2 wet/dry conversion 657R0918

20: Language
oD  language German/English
oDF  language German/French
oE  language English/German
oEF  language English/French
oFE  language French/English

21: Special configuration

z1  special configuration 657R1030 KS1D RBT
z2  special configuration analogue input 1-current 0 ... 20 mA analogue input 2
voltage 0 ... 10 V
z3  special configuration stainless steel housing LT2 without window
z4  special configuration stainless steel housing LT2 viewing door
z5  special configuration stainless steel housing LT2K with window
z6  special configuration assembling in EEX-housing 657R0165
z7  special configuration firing rate analogy via analogue input 1 and analogue
input 2 - limit value 1
z8  configuration by order

22
 4 Technical Description

4.5 Options

4.5.1 Display and Operating Unit Type 657R0831

Fig. 4-5 Optional with LT2 in wall-mounting housing type 657R102

23
 4 Technical Description

4.5.2 Remote Display Software

The Remote Display Software is a PC software to configure the LT2. Use it instead of the dis-
play and operating unit, and to store and restore the data set.
• Remote Display Software including interface RS 232 module for PC type 657R1101
• Other licences for the Remote Display Software type 657R1102
• Suitable with windows-based computers
• Connection with LT2 via RS 232 interface.
Refer to special documentation DLT1004.

Fig. 4-6 Remote Display Software

24
 4 Technical Description

4.5.3 Calculation of Combustion Efficiency

The calculation follows the formula:

hF = 100 (qAf + qAg) %
qAf = Exhaust gas loss through free heat
qAg = Exhaust gas loss through bounded heat
qAf = (tA - tL) * [A2/21 - O2 + B]
Calculation of exhaust gas losses is based on the following mean fuel values:
Oil A2 = 0.68; B = 0.007
Gas A2 = 0.66; B = 0.009
It is assumed that the combustion is CO and soot-free.
Exhaust gas losses through bound heat are not taken into account.
Display:
Efficiency 0 ... 100 %
Exhaust gas losses 0 ... 100 %
Exhaust gas temperature 0 ... 320 °C
Intake air temperature 0 ... 320 °C
Other ranges on request
Measurement accuracy:
Temperature - better than 2 K
Efficiency/exhaust gas losses - better than 0.2 %
Electric connections:
depending on configuration/components
Measurement card:

3 4
22 26
21 25
20 24
19 23
Y2 - Pt100
measuring element

X2 - no connect
In the 657R0896 version, the intake air is specified as a constant.
The intake air temperature is not measured. Only recommended where the intake temperature
remains nearly constant over the whole year.
Set the average temperature of the intake air in parameter 1450.

25
 4 Technical Description

4.5.4 Calculation of the CO2 Concentration

Calculated by referring to the fuel from the measured O2 value and the CO2 maximum
value type 657R0910
The calculation follows the formula:
CO2 = CO2 max – (21 % -O2 / 21 %)
The calculation is based on the following max. CO2-contents at  = 1  O2 = 0 % vol.
referenced to dry exhaust gas.
Light fuel oil EL 15.4 Vol. %
Natural gas H 12.0 Vol. %
Heavy fuel oil HFO 15,9 %
Natural gas L 11.7 Vol. %
Individual specification of CO2 max. is possible via the parameters 846, 862, 878 and 894.

26
 4 Technical Description

4.5.5 Firing Rate Dependent and Fuel Specific Limit Values/Limit Curves

The burner firing-rate value or some other measured quantity is supplied via analogue input 4
or via LAMTEC SYSTEM BUS. Instead of fixed limit values you can enter fuel-specific curves
with 2 up to a maximum of 8 checkpoints.

1 limit curve 1
fuel (curve 5)
2 limit curve 2
fuel 1 (curve 7)
3 burner firing rate [%]
4 regular firing rate input
[mA]

Fig. 4-7 Limit curves (factory settings), parameters adjusted to values

below threshold.
Possible combinations:
either
• 2 fuels with 4 limit curves / limit values per fuel
• 4 fuels with 2 limit curves / limit values per fuel
For details see supplement to the operating instructions for the optional "Display and operat-
ing unit”

4.5.6 Draught Measurement (Available on Request) Type 657R0110

Differential pressure sensor for measuring

• Flue draught
• Combustion chamber pressure
• etc.
On request → please specify the required pressure range.

4.5.7 1 ... 4 Analogue Output (0/4 ... 20 mA, 1 ... 10 V)

Max. 2 floating (output 1 and 2), max. potential difference  20 V, configurable in any order
Direct current 0/4 ... 20 mA, load 0 ... 600 
Direct voltage 0 ... 10 V, load ≥ 10 k
Analogue output card 0/4 ... 20 mA, 0 ... 10 V type 657R0050
Analogue output card 0/4 ... 20 mA, 0 ... 10 V, floating, max. potential difference  20 V
type 657R0051

27
 4 Technical Description

4.5.8 Digital Outputs

Parameter group 1030 to 1099

Digital output 1: Via internal relay (1 switch over) to LT2supply section
electronics
1 ... 48 VDC/AC, 3 A
as standard
0 ... 230 VAC, 2 A
Digital output 2 to 7: Via internal relay module
type 660R0857 6 relays (1 switch over), switching capability
(optional) max. 230 VAC, 4 A
alternative (on request)
The outputs can be configured arbitrarily via the (optional) display and operating unit and the
Remote Display Software. (parameter 1030 ... 1099)

Fig. 4-8 Relay module type 657R0857

NOTICE
To avoid EMC faults shield the branch lines of the relay modules.
When using unshielded cables loop them twice trough the provided ferrite ring.

28
 4 Technical Description

4.5.9 1 ... 4 Analogue Inputs

• Analogue inputs by measurement cards, arbitrary configuration e.g. for temperature sen-
sor, further pressure sensors, LS2 Lambda Probe, standard signals etc; max. 2 of these
floating,
max. potential difference  20 V

External communication processor with PROFIBUS DP module

By plug-in card on LT2 power pack electronic (max. 2)
• Analogue input card 0/4 ... 20 mA type 663P6001
• Analogue input card 0/4 ... 20 mA with supply 24 VDC for transmitter LT1/LT2 type
663P6002
• Analogue input card for potentiometer 1 ... 5 k type 657P6000
• Input temperature for Pt100 type 657R0890
range of measuring alternative 0 ... 320 °C/608 °F
0 ... 850 °C/1562 °F (please specify when ordering)

Electric connection see chapter11.4 Electric Connections Device Side

29
 4 Technical Description

4.5.10 BUS interface

Electrical connector via LAMTEC SYSTEM BUS to external communications processor.

Fig. 4-9 External communication processor with PROFIBUS-module

• For the systems:
– PROFIBUS DP, type 663R040-1PB/LT
– Modbus RTU, type 663R040-3MBK/LT
• (Details see separate publication)

30
 5 LAMTEC SYSTEM BUS (LSB)

5 LAMTEC SYSTEM BUS (LSB)

5.1 Jumpers, LED, Fuses and Terminals

1 F6 - T315 mA 5 VDC - LSB

2 BR12, BR13 → position ’C’ - CAN

3 BR105 → position 2-3 (left)
4 LED1 – green → RxD from LSB *
LED2 – yellow → TxD from LSB *
5 BR102 – BR104 position 1-2 (left)
base board V.03 and higher
6 BR101–120 termination resistor LSB,
→ position 1-2 (right)
without terminating resistor
→ position 2-3 (left)
with terminating resistor
7 terminal 71 → CAN-GND
terminal 74 → CAN-H
terminal → CAN-L

* LED flickering

Fig. 5-1 LT2 assignment

5.2 Function

NOTICE
The data of the LT2 is only transferred by LAMTEC SYSTEM BUS if the device is set to MEAS-
URING and not to MAINTENANCE or ERROR.
If the communication works properly LED 1 and LED 2 are flashing.

31
 5 LAMTEC SYSTEM BUS (LSB)

5.3 Wiring Example

Master ID9 with Display LAMTEC SYSTEM BUS

BR101: 1-2 termination not active
CAN-H KL. 74
CAN-L KL. 75
CAN-GND KL. 71
Slave ID10 without Display LAMTEC SYSTEM BUS
BR101: 2-3 termination active
CAN-H KL. 74
CAN-L KL. 75
CAN-GND KL. 71

NOTICE
Set the master LT (with display) to LSB- device ID 9 and the slave to ID 10 for remote display
via LSB (LT-parameter 3801).
It is not possible to connect the master (LT with display) to the remote software and to the re-
mote display at the same time. The connection which is established first takes priority over the
other.
It is possible to use the remote software on the slave LT (LT without display) simultaneously.
Establish and interrupt the remote connection in the menu diag/remote. It is possible to inter-
rupt the connection at the master and the slave as well.

32
 6 Commissioning/Decommissioning

6 Commissioning/Decommissioning
6.1 Factory Settings

6.1.1 Device Configuration

(unless otherwise specified in the order)

Measuring range: 0 ... 30 % vol O2
Resolution: 0,1 % vol O2 in range of 0 ... 18 % vol O2
1 % vol O2 in range over 18 % vol O2
Probe temperature: 880 K
(Parameter 141)
Analogue output 1: 4 ... 20 mA = 0 ... 10 % vol O2
via parameter 531
0 ... 20 mA adjustable
Load: 0 ... 600 
– Measurement span can be freely configured via the parameters 532 and 533
– Relay outputs Idle current principle
Relay output 1: Collecting fault message
Relay output 2: Warning and maintenance
Relay output 3: Measurement
Relay output 4: Boundary value 1
Relay output 5: Boundary value 2
Relay output 6: Boundary value 3
Relay output 7: Boundary value 4
– Boundary values
Boundary value 1: Switched off
Boundary value 2: Switched off
Boundary value 3: Switched off
Boundary value 4: < -5 mV value smaller than threshold
3 seconds release delay
Reset mode "automatic”
(for monitoring the probe;
air value))
– Digital inputs
Input 1: Reset fault/warning
Input 2: Reset boundary value messages
Input 3: Offset-calibration maintenance on/off
Input 4: PID-controller off
Input 5: Maintenance on/off (from software 1V33a)
Input 6: Fuel 2 (Gas)*
Input 7: Fuel 3*
Input 8: Fuel 4*
* Parameter 836 - service level must be present at digital inputs.
Without signal default heating oil EL.

– RS 232-interface device address 1

9600 Baud
parity none

33
 6 Commissioning/Decommissioning

6.2 Preliminary Works

6.2.1 The LT2 Lambda Transmitter's Display and Operating Elements

The LT2's operation and the display of measured values, operational and error messages take
place by the (optional) display and operating unit, or by a PC in combination with the Remote
Display Software. The LT2 itself has only limited operating capabilities, which do not allow LT2
to display or process all the functions necessary for operation, maintenance and servicing.

NOTICE
The internal display and operating elements are not freely accessible with LT2 for panel
mounting!

1 Display of operating
mode
2 Warning /
Fault display
3 Maintenance switch
4 Multifunction key

Fig. 6-1 Internal display and operating elements on the processor

board

6.2.2 Monitor Output

The monitor output (terminals 31 (-) and 32 (+)) makes it possible to connect a multimeter for
example. The device indicates the following values by the monitor output:
– O2 measured value
– Probe voltage [U]
– The measuring cell's AC internal resistor [Ri]
DIP switch processor card

SW 1 SW 2 Monitor output function

OFF OFF O2 measured value 0 ... 2.5 V = 0 ... 25 % vol O2

ON OFF O2 probe voltage (U-O2) 0 ... 2.5 V = 0 ... 250 mV

OFF ON O2 cell’s internal resistance 0 ... 2.5 V = 0 ... 250 

Input resistance of the connected measuring device greater than 10 k.

34
 6 Commissioning/Decommissioning

6.2.3 Internal Display and Operating Elements

Legend: LED is off flashes lights up

Multifunction key T 2 Operation (green) LED 6 Operating mode (green) LED 5

Maintenance switch S 1

Operation Measurement
Calibration

Offset compensation (flashes slowly)

With test gas/comparative measure-
ment (flashes quickly)

Maintenance mode off

Maintenance mode on

Maintenance (orange) LED 1 Warning/fault (red) LED 12

Maintenance mode active No warning / fault

Normal operation At least one warning present
At least one fault present

NOTICE

Function Key operation

Toggle the displayed warning/ fault Press briefly
Reset the displayed warning/fault Press for longer than 3 sec*
Abort cold-start Press for longer than 3 sec**
Trigger an offset calibration to ambient air Press key for longer than 3 sec
during measurement**
* Some warnings and faults cannot be reset if the error is still present or the routine is
still running.
** If at least one warning or fault is still present, the key must be pressed for longer than
6 seconds.

35
 6 Commissioning/Decommissioning

6.3 Measurement Start-up

• Connect the probe but do not install it

Switch to MAINTENANCE
either via the display and operating unit in menu
[diag] or with the maintenance switch S1

Fig. 6-2 Maintenance (orange) LED 1

NOTICE
The maintenance switch always has priority.

– MAINTENANCE mode • Switch on voltage

active • LED 1 shows MAINTENANCE
– Normal OPERATION • Probe warms up

– MAINTENANCE mode OFF

• COLD START is shown
LED 6 OPERATION ON
LED 5 MEASUREMENT OFF
– MAINTENANCE mode ON

NOTICE
During cold start the display and operating unit or the monitor output indicate the cell’s inner
resistance RI.

The measurement function is ready for operation after 10 minutes.

Measurement is shown
LED 6 OPERATION is ON
LED 5 MEASUREMENT is ON

NOTICE
The cold-start delay can be activated from the display and operating unit → [cal] key. Proceed
as prompted by the menu, or interrupt by pressing the multifunction key T2 (for longer than 3
seconds, or if a warning or a fault is still present, for longer than 6 seconds).

• Observe the cell’s inner resistance and read the probe voltage alternatively via display and
operating unit (if available) or at the monitor output.

NOTICE
To read the probe voltage --> confirm with [meas] and choose probe voltage US.

36
6 Commissioning/Decommissioning

After a 10 minutes heating phase, the probe voltage

would be stabilised to values between -5 and -15 mV
and the measuring cell (Ri probe) internal resistance
would be stabilised to values below 100, for new
probe below 20 . Are positive values displayed in
air, the probe’s polarity is reversed. Swap probe con-
nection on terminals 33/34.
Fig. 6-3 Multifunction key T2 Proceed with offset calibration alternatively by using
display and operating unit in [cal] or the multifunc-
tional key T2 (hold for more than 3 seconds in
MEASURING mode).

NOTICE
Calibration is displayed
LED 6 OPERATION is ON
LED 5 MEASUREMENT is flashing
• Wait for offset calibration to be finished.
Flashing has stopped.
• Enter probe temperature from the test protocol, parameter 141 ’customer access level’;
alternatively see separate manual in
– Display and operating unit (optional)
– Remote display software (optional)
• Exit MAINTENANCE

NOTICE
"Probe temperature T"
The LT2 Lambda Transmitter and LS2 Lambda Probe are not adjusted to each other. The LS2
Lambda Probe is subject to production dispersion, which can be compensated by offset cali-
bration and probe temperature. A probe calibration with test gas is not necessary.
The probe temperatures determined by the end test can be found in the test protocol (which
is part of the delivery).

• Install probe

NOTICE
When installing or operating the probe, ensure that the probe does not get into contact with
oil, grease or boiler cleaning materials.
This does not apply only to the cell, but also to the connector region!
The thread and the clamping ring should be treated with mounting paste type 655R1090 to
prevent for seizing.
Poisoned or contaminated probes can be identified by an air voltage of -20 …- 30 mV.
The probe must always be in operation when it is installed. This avoids the precipitation of
moisture on the measuring cell, which in certain cases can lead to erroneous measurements
and to the probe's destruction!

37
 6 Commissioning/Decommissioning

6.3.1 Install the Probe in the PIF and Align the GED

• Start up combustion
• Measured value plausible?
Check if necessary via comparative measurement

NOTICE
Almost all extractive O2-meters measure ’dry’, in contrast to the in-situ ZrO2-meters; i.e. mois-
ture is extracted from the flue gas through a purification process (cooler) or a chemical absorb-
er (silica gel). This reduces the volume of the measured gas, and thus the proportion of O2
increases. This fact must be taken into account during comparative measurement. A diagram
for converting wet into dry measurements can be found in chapter 11.4 Electric Connections
Device Side

• If large deviations are present, it is possible to compensate for the values obtained via
– the display and operating unit, in [cal]
– the service and diagnostic software
– as follows, using the multifunction key:
Measure the O2 value at the monitor output or analogue output. Start calibration with the mul-
tifunction key. LED 5 should flash rapidly
Briefly pressing the multifunction key increases the output O2 value by 0.1 %

Pressing for a longer (time s)

The modification direction is inverted.

NOTICE
Calibration should only be carried out if it was previously ascertained that the comparison in-
strument is measuring correctly (e.g. by using test gases).

In any event, offset calibration should previously have been carried out in operational (warm)
conditions.
It is necessary to ensure that ambient air is present at the measurement site. If this is not en-
sured, the probe must be dismantled again for the offset

38
 6 Commissioning/Decommissioning

6.4 Setting up Service Warnings

Service warnings 1 and 2 are designed to draw attention to regular servicing.

The service warnings can be freely defined by the operator, e.g.
Service warning 1  check probe
Service warning 2  dismantle and clean probe
The appropriate cycle times can be specified via the parameters 1260 and 1261 in the range
1 to 65535 hours.

6.5 Decommissioning

In order to be sure to avoid damaging the probe’s ZrO2 measuring element, the probe must
be dismantled before the system is shut down or immediately after the supply voltage is
switched off.

NOTICE
Dismantle the probe before shutting down the measurement system.

CAUTION!
Hot probe!
The probe may be hot during mounting/demounting! Risk of burns!
 Wear appropriate protective clothing.
 Be careful.
 Do not place the hot probe on flammable material.

NOTICE
Once dismantled, the probe can be stored indefinitely. The zirconium element is only con-
sumed during operation (measuring cell at operating temperature). This also applies where a
probe has already been used previously.

39
 7 Operation

7 Operation
7.1 Operation/Measurement Value Display

• Display and operating unit (optional) is included as a

standard in LT2 19” for panel installation.
• Service and diagnostic software (optional)
• Limited by multifunction key and monitor output

7.1.1 Measurement Value

• O2 actual value 0 … 30 % vol O2

Resolution: 0.1 % vol O2
up to 18 % vol O2
1.0 % vol O2
above 18 % vol O2
• Probe voltage -30 ... +150 mV
Resolution: 0.1 mV
• AC internal resistance of the ZrO2 cell 0 … 750 
Resolution: better than 0.2 
Displayed up to 999.9 
• Exhaust gas temperature (optional) 0 … 320 °C/32 °F ... 608 °F
Resolution: 1 °C/33.8 °F
Alternatively: 0 ... 850 °C/
32 °F ... 1562 °F
Resolution: better than 2 °C/
35.6 °F
• Combustion efficiency (optional) 0 … 100 %
Resolution: 0.1 %
• Calculated CO2-concentration (optional) 0 … 20 % vol
Resolution: 0.1 % vol
• CO/H2 concentration, shown as 0 … 10,000 ppm
COe [CO equivalent] Resolution: variable 1 ... 100 ppm
depending on meas-
ured value
Alternatively: 1 % of measured
value,
not better than 1 ppm
• Customised values Can be freely configured, e.g. exhaust
gas, temperature, efficiency, CO2 con-
centration etc.

40
 7 Operation

7.1.2 Commands

• Abort ’Cold-start delay’  Directly during measurement

• Offset compensation  Compensate probe to ambient air, 21 % vol O2
• Calibration Perform measured value compensation by compara-
tive measurement. Test calibration only in connection
with a special testing device or with LS2-HT possible.
• Fault/warning  Reset
• Limit values  Reset

7.1.3 Status Signals

• Measurement
• Calibration offset [Cal - offs]
• Calibration [Cal - gas]
• Maintenance
• Cold-start
• Probe heating active
• Measurement/no measurement
• At least one warning active
• At least one fault active

Status message during calibration

• Offset
• Cal-Gas

7.1.4 Operating Parameters

• Downward counter, cold-start delay

• Time, date
• Operating hours counter

41
 7 Operation

7.2 General Instructions for Operation

7.2.1 Measurement During Distinct Pressure Surges at the Measuring Site

If the display jumps badly, damping can be increased via the (optional) display and operating
unit and the service and diagnostic software (i.e. by increasing the integration's time-con-
stant); this steadies the display: parameter 360 - Operational release level. However, this
slows down the display in terms of reaching an end state.

NOTICE
Large damping simultaneously leads to an artificial slowing down of the measurement signal.

7.2.2 Operational Failure, Switching On and Off

In the event of long interruptions during operation, which are lasting for longer than approx. 3
months, it is recommended to switch off the measuring system. The probe should be disman-
tled to avoid damage (see chapters 6.4 Setting up Service Warnings and 6.5 Decommission-
ing.).

NOTICE
Recommendation: Continue with the measurement in case of short service interruptions.

7.2.3 Liquid Purification

To perform a liquid purification of the boiler is possible, if the probe is dismantled before. Per-
forming a liquid purification to an installed probe, can damage the probe. An error free opera-
tion is no longer possible.

NOTICE
For the liquid purification, the probe must be dismantled by all means. A liquid purification of
an installed probe will damage the probe.

42
 8 Service and Maintenance

8 Service and Maintenance

To perform a liquid purification note the following:
Only perform a liquid purification, if the probe is dismounted.Performing the liquid purification
without dismounting the probe will damage the probe. The probe will not function properly after
that.

NOTICE
Always dismount the probe before liquid purification. Liquid purification without dismounting
the probe will damage the probe.

8.1 Checking the O2 Probe

8.1.1 Checking the Air Voltage

• Switch off the facility

• Pre purge, until no more flue gas is present at the
measurement site (approx. 1 minute).
• Turn off the pre purge.
• Carry out offset calibration either by
• the (optional) display and operating unit in
Fig. 8-1 T2 multifunction key
[cal] - menu-driven
• the (optional) service and diagnostic software
• T2 multifunction key

NOTICE

Functions Handling of the Keys

Toggle the displayed warning/fault Press shortly
Reset the displayed warning/fault Press for longer than 3 sec.*
Quick start of the measuring gas pump - abort of Press for longer than 3sec.**
the cold start
Trigger an offset calibration Press key for longer than 3 sec.
during measurement **
* Some warnings and faults cannot be reset if the error is still present or the routine is
still running.
** If at least one warning or fault is still present, the key must be pressed for longer than
6 seconds.
If probe voltage is outside the permissible range, the warning ’Offset calibration to air invalid’
is indicated.
• Read out probe voltage at LT2 either by
– the display and operating unit (option)
– the service and diagnostic software (option)
– measure probe voltage with a multimeter;
Connect a digital voltmeter in parallel to the probe at terminal 33 (-) and 34 (+).
Compare the measured voltage with the displayed voltage (US).
• Valid range: 5 mV … -30 mV
• If the probe’s voltage is above/below this range → replace probe

43
8 Service and Maintenance

NOTICE
Do not forget!
Perform a new offset-calibration in ambient air and enter the probe’s new temperature value
after replacing the probe.

Limit value 4 is set at the factory: An automatic check of the probe is possible at downtime and
at pre-purge of the plant. No response of the limit values!
Limit value 4 → 5 mV shortfall, automatic reset
Delay time of the trigger 3 seconds
-30 mV shortfall is monitored by fault no. 1
An intact probe does not cause fault no. 1.
If fault no. 1 ’probe voltage < -30 mV’ occurs reset it manually.

NOTICE
After the loss of the power supply (and therefore the heating of the probe) the probe voltage
may decrease for a moment to -30 mV in the heating period.

Recommendation: Retain the factory-set limit value 4 for safety reasons.

If the facility cannot be switched off, the probe must be dismantled for examination.

44
 8 Service and Maintenance

8.1.2 Checking by Counter Measurement

Precise checking of the measurements is only possible through counter measurement with a
second probe, or by comparing the measured values after probe replacement.

NOTICE
During counter measurement, check whether the instrument being used measures wet or dry.
Those with an advance gas cooler are always used for dry measurement. This also applies to
instruments that extract moisture via a chemical compound. The LS2 Lambda Probe meas-
ures wet. The difference between wet and dry measurements can be obtained from the dia-
gram in the Appendix (see chapter 11.5 Wet/Dry Measurement Deviations, Conversion Table).

• If large deviations are present, it is possible to compensate for the values obtained via
– the display and operating unit, in [cal]

NOTICE
Confirm the new calibration value with ENTER or OK during the calibration of the measure-
ment value with the display and operating unit → [cal]. If not, the menu will be quit automati-
cally after 15 s and the new calibration value is discarded.

• the service and diagnostic software

• as follows, using the multifunction key:
– Measure the O2 value at the monitor output or analogue output.
– Start calibration with the multifunction key.
– LED 5 should flash rapidly (see chapter 6.2.3 Internal Display and Operating Ele-
ments).
– Press briefly: The O2 value is changed by 0.1 %
– Press long (> 3 seconds): The direction of change is reversed.

NOTICE
Which instrument measures correctly?
Compensation should only be carried out if it was previously ascertained, e.g. by using test
gases, that the comparison instrument is measuring correctly.

45
 8 Service and Maintenance

8.2 Checking the LT2

8.2.1 Checking the LT2's Measuring Input

Connect a digital voltmeter between terminals 33 (-) and 34 (+), in parallel to the probe. Com-
pare the measured voltage with the probe voltage displayed (US).
Range: -30 mV … +300 mV.
If the difference is less than 1 mV, the LT2 is operating correctly.
If the difference exceeds 1 mV, repeat the above step with another digital voltmeter.

NOTICE
Check the accuracy of the digital voltmeter used.

If the difference persists → exchange the instrument.

8.2.2 Checking the Probe's Internal Resistance Measurement

Checking the probe’s inner resistance

 Available only with a probe simulator, type 655R1030.
1. Connect the probe simulator to terminals 33 (-) and 34 (+)
2. Set an internal resistance < 200 W with a potentiometer
3. Check with volt meter:
a) AC voltage between terminals 33 (-) and 34 (+).
b) Indication in mV = corresponds to one half of the probe's internal resistance.
c) Ri > 200  – after 10 s Warning ’Inner resistance [Probe Name] too high’
Ri > 300  – after 10 s Failure ’Probe broken wire/Probe defective’
Example: 75 mV 150 

NOTICE
During COLD START the monitoring of the probe’s internal resistance is disabled.

8.3 Maintenance

Check the measurement system on a monthly, quarterly or semi-annual basis, depending on

the application.

8.3.1 Consumable

Lambda Probe Mean lifetime

– natural gas and light fuel oil: 3 ... 5 years
– with heavy fuel oil, coal and biogas: 1 ... 3 years

46
 9 Faults/Warnings

9 Faults/Warnings
Messages in plain text (see chapter 7.1.3 Status Signals).
• by (optional) display and operating unit, in menu [diag]
• by Remote-display software (optional)
• by LED row, LED 7 to 12, on LT2's processor board
If several faults/warnings are present, they can be called up in sequence by activating the T2
multifunction key.

9.1 Faults

Legend LED is off flashes lights up

Message by LED line, LED 7 to 12, LED 12 flashes
Faults (flashing)

12 11 10 9 8 7 Fault No.:
No warnings/faults active

1 Probe voltage < -30 mV

2 Probe heater faulty

Display of active faults (red), flashes 5 Probe broken wire/probe faulty

9 Dynamic response missing

11 Fault analogue outputs

47
 9 Faults/Warnings

9.2 Warnings

Legend: LED is off flashes lights up

Message by LED row, LED 7 to 12, LED 12 lights up.
Warnings (LED ON)

12 11 10 9 8 7 Warning No.:

No warnings/faults active

1 Internal resistance too high

2 Offset voltage to air invalid

Display of active warnings (red), Analogue input 1: input value too
LED(s) permanently on. 19 high/low
Analogue input 2: input value too
20 high/low
Analogue input 3: input value too
21 high/low
Analogue input 4: input value too
22 high/low
Configuration error analogue
23 output

24 Service warning 1

25 Service warning 2

26 No probe dynamics *

27 Dynamic test triggered *

* Only relevant in conjunction with an integrated O2 control system.

Without an integrated O2control system the dynamic test should remain OFF 
parameter 1330 = 0.

48
 9 Faults/Warnings

9.3 Resetting Faults/Warnings

• by (optional) display and operating unit, in [diag], menu-driven

• by service and diagnostic software in [status], menu-driven
• by digital inputs – input 1
• by pressing the T2 multifunction key (for longer than 3 seconds per fault).
If several faults are present simultaneously, press the multifunction key several times.
Press the key [diag] to switch to warnings and faults. Select the single warnings, faults or limit
values with the cursor keys (up/down).

NOTICE
Limit values are displayed only if they are activated in parameters 930/940/950/960 (access
level ’Service’).

NOTICE
Reset all warnings or faults by quitting them. If necessary eliminate the cause of the warning/
fault.

49
 9 Faults/Warnings

9.3.1 Faults - Causes and Solutions

9.3.1.1 Probe voltage too low

• Probe + / - reversed probe connection terminal 33-34 change

• Probe poisoned replace

NOTICE
Probe voltage to air +5 to –30 mV

9.3.1.2 Defective LS2 Probe Heating

NOTICE
In 99 % of all cases, the LS2 Lambda Probe was disconnected during operation. Reset fault
either by the multifunction key or by the display and operating unit etc.

1. Reset fault either by the multifunction key or by the display and operating unit etc.
2. A defect only exists if the fault cannot be reset.
Possible causes:
• Check fuse F 5 (see chapter 11.4.4 LT2 Power Electronic Type 657E1882
• Check the probe heater. In an intact heater, ca.10 (9  ... 11 ) can be measured
between terminal 35 and 36. If not (R ) heater faulty. Replace probe.
• If intact, check the supply voltage: The probe heater must be supplied with about 13 VDC,
cyclically reversed. If not, check the wiring and the terminals and tighten if necessary.

NOTICE
The probe is heated with direct current at approx. 13 V, cyclically reversed. Therefore the use
of a multimeter to measure it is somewhat difficult.

NOTICE
The current heating data can be read out from LT2 operating parameters 41/42/43.

9.3.1.3 Broken Wire Probe/Defective Probe

This message is indicated if the AC internal resistance (Ri) or the ZrO2 cell exceeds the per-
missible limit of 300 . Before or after this message you normally will get the warning ’Inner
resistance [probe] too high’.
Possible reasons:
• The probe is disconnected (measuring signal on terminals 33 to 34)
• Loose connection  check the terminals, re-tighten
• Probe too cold, possibly enhance the heating power gradually (0.5 W)
• Check wiring, if OK  replace probe

50
 9 Faults/Warnings

9.3.1.4 No Probe Dynamics

No probe dynamic detected. Check the probe.

NOTICE
Testing is shut off on delivery.
Activate testing in parameter group 1330 to 1334.
The testing checks, if the measuring value changes more than the parameter set threshold
value during a specified time.
Only valid in combination with an integrated O2 control.

9.3.1.5 Fault Analogue Output

Check the parameters of the analogue outputs.

• Parameter 530 … 539 analogue output 1
• Parameter 540 … 549 analogue output 2
• Parameter 550 … 559 analogue output 3
• Parameter 560 … 569 analogue output 4
Check the analogue outputs on the processor electronic and replace them if necessary. An
analogue output might be activated, but is not assembled 

Check assembly.
(see chapter11.4.3 Fuses)

9.3.1.6 O2 Value Is Incorrect

If a control measurement results in a different O2 value than the one displayed:

• Has the relationship between wet/dry measurement been taken into account?
see chapter 11.5 Wet/Dry Measurement Deviations, Conversion Table
• Check LT2 and probe, see chapter 8.2 Checking the LT2
• Commission the new probe as described in chapter 6 Commissioning/Decommissioning
• Measuring value too high? Secondary air, check sealing and hose connections if they are
tight.

NOTICE
During counter measurement, check whether the instrument being used measures wet or dry.
Those with an advance gas cooler are always used for dry measurement. This also applies to
instruments that extract moisture via a chemical compound. The LS2 Lambda Probe meas-
ures wet. The difference between wet and dry measurements can be obtained from the dia-
gram in the Appendix, see chapter 11.5 Wet/Dry Measurement Deviations, Conversion Table

51
 9 Faults/Warnings

9.4 Warnings - Causes and Solutions

In general: Warnings do not affect the measurement functions.

9.4.1 LS2 Internal Resistance too High

This message is output if the AC internal resistance (RI) of the ZrO2 cell exceeds the permis-
sible limit of 200 during operation.
Possible cause:
Probe aged (worn out)  Obtain a spare probe and replace.
Measurement can continue, using caution. Check accuracy by counter-measurement,
see chapter 7 Operation
– Check fuses F2, see chapter11.4.3 Fuses
– Fault in supply section electronics  replace
Check the Lambda Transmitter’s electronic:
Measure the AC voltage across LT2 terminals 33 and 34, using a multimeter.
The result in mV corresponds approx. to half the AC internal resistance.

9.4.2 Offset Voltage to Air Invalid

The voltage determined during offset compensation is not permissible.

Check whether probe is in air.
If yes - check probe voltage to air.
Permissible voltage range +5 … -30 mV.

52
 9 Faults/Warnings

9.4.3 Analogue Inputs 1/2/3/4 Input Value too Large/too Small

The input value at the relevant analogue input is outside the permissible range.
• Check parameters 574/584/594/604 (minimum) and parameters 578/585/595/605 (maxi-
mum). Parameters 570/580/590/600 indicate the current value.
• Check wiring  poles reversed?
• Check source (connected instrument).
• Analogue input card defective? Replace it.

9.4.4 Configuration Error at Analogue Outputs

Parameters have been set for analogue outputs not physically found. Check parameters 539,
549, 559, 569 and 530, 540, 550, 560 and compare with the fitted cards.
If necessary, replace the analogue output cards and/or processor card.

9.4.5 Service Warning 1/Service Warning 2

The service warnings are designed to draw attention to regular servicing. The service warn-
ings can be freely defined by the operator, e.g.
Service warning 1  check probe
Service warning 2  replace probe
The appropriate cycle times can be freely configured by the parameters 1260 and 1261.

53
 10 Spare Parts

10 Spare Parts
The following is a list of relevant spare parts. It is recommended to maintain a stock of the
spares marked (1).
Spares marked with the footnote (2) should be kept if considered appropriate.
Spares marked with the footnote (3) should be kept only if the system is equipped with the rel-
evant option.

Spare parts

Display and Operation Unit LT2 657R0833 (3)

1 Replacement main board for LT2, without connector set 657E1882 (2)
1 Processor electronic board for LT2 657R1874 LT2 (2)
1 Replacement power supply transformer for LT2 657P0342 (2)
1 Analogue output module 0/4 ... 20 mA; 0 ... 10 V 657R0050 (2)
1 Analogue output module0/4 ... 20 mA; 0 ... 10 V floating, Max. potential difference 20 V 657R0051 (3)
1 Analogue input module LT1/LT2 Potentiometer 1 ... 5  657P6000(3)
1 Analogue input module 0/4 ... 20 mA 663P6001 (3)
1 Analogue input module 0/4 ... 20 mA with supply 24 VDC for transmitter 663P6002 (3)
1 Analogue input module 0/2 ... 10 V 657P6005 (3)
1 Temperature input for Pt100 657R0890 (3)
1 Temperature sensor Pt100, 250 mm (9.843" in) long 657R0891 (3)
1 Relay card for digital outputs, 6 relays, 1 switcher each 660R0017 (3)

54
 11 Appendix

11 Appendix
11.1 Technical Data LT2 Lambda Transmitter

11.1.1 Technical Data LT2 in Wall Mounting Housing

Fig. 11-1 LT2 in wall-mounted housing

Fig. 11-2 Wall mounting housing

55
11 Appendix

Fig. 11-3 Wall mounting housing with reference gas pump

LT2 in wall mounting housing

Housing Housing in sheet steel, powder-coated

Dimensions (HxWxD) 400x300x150 mm/15.75"x11.81"x5.91" in - without reference
gas pump
500x300x200 mm/19.69"x11.81"x7.87" in - with reference
gas pump
Colour Light grey RAL 7035
Weight 10 kg/22.05 lb
with display and operating unit +0,5 kg/1.10 lb
Control elements Display and operating unit with LCD graphic display (option)
LSB Remote Software (option)

56
11 Appendix

Characteristics
Power supply 230 VAC and 115 VAC
+10 % / -15 %, 48 Hz ... 62 Hz
Use only in earthed networks!
Power consumption max. 50 VA short-term 150 VA (heating phase probe)
Display LCD graphic display 100x80 mm (WxH)/3.94"in.x3.15" in
in panel installation housing = standard
in wall mounting housing = optional
Resolution O2: 0,1 Vol. % O2 in range 0 ... 18 Vol. % O2
1,0 Vol. % O2 in range 18 ... 30 Vol. % O2
CO: 1 ppm in CO range
Measurement accuracy (standard value) With Lambda Probe LS2:
– other Measurement accuracies can be 0,1 Vol. % O2 in range 0 ... 18 Vol. % O2
achieved depending on the design 1,0 Vol. % O2 in range 18 ... 30 Vol. % O2
With Combination Probe KS1 or KS1D:
O2:10 % of the measured value, no more precise than
0,3 Vol. % O2
CO: 25 % of the measured value, no more precise than
10 ppm on natural gas combustion, after previous calibration
under operating plant conditions with a CO-reference
measurement in measuring range 0 ... 100 ppm
Time for operational readiness approx. 10 minutes after MAINS ON
Cold start delay automatically cold start delay, 10 min.

Analogue outputs
Monitor output 0 ... 2,55 VDC, load >10 k, 100 nF
1 ... 4 current/voltage outputs 1 (LS2, KS1) or 2 (KS1D) standard – up to 4 options
direct current 0/4 ... 20 mA load 0 ... 600 
direct voltage 0 ... 10 V load 10 k non floating (potential
isolation optional)

Analogue inputs
Analogue inputs: 1 ... 4 via plug-in card on LT2 power pack electronic
– Analogue input module potentiometer 1 ... 5 k
type 657P6000
– Analogue input module 0/4 ... 20 mA type 663P6001
– Analogue input module 0/4 ... 20 mA with supply 24 VDC
for transducer type 663P6002
– Temperature input for Pt100 sensor type 657R0890
temperature range 0 ... 320 °C/32 °F ... 608 °F/
0 ... 850 °C/32 °F ... 1562 °F resolution 1 °C/33.8 °F

Digital output
Digital output 1 standard + 6 optional
– 1 relay output 0 ... 230 VAC, 2 A – 0 ... 42 VDC, 3 A
collective fault indicator
– relay card with 6 relays (1 changeover switch)
0 ... 230 VAC, 2 A – 0 ... 42 VDC, 3 A

57
11 Appendix

Digital input
Digital input 8 inputs - configurable (any)
Factory settings: 24 VDC referenced to instrument potential,
Can be switched via jumper to floating, for external voltage
source.

Interface
Interface LAMTEC SYSTEM BUS
RS 232 only in combination with PC Remote Software
BUS connection PROFIBUS DP
Modbus RTU

Operating condition
ambient temperature Operation: -20 °C ... +60 °C/-4 °F ... 140 °F
Transport and storage: -40 °C ... +85 °C/-40 °F ... 185 °F
Protection class to DIN 40050 IP65
CE Declaration of Conformity 2014/30/EU – EMC Directive
2014/35/EU – Low Voltage Directive
2011/65/EU – RoHS Directive

58
 11 Appendix

11.2 Technical Data LS2 Lambda Probe

Fig. 11-4 Lambda Probe LS2 in housing with gas extraction device (GED) and probe installation fitting
(PIF)

Fig. 11-5 Lambda Probe LS2 in housing with gas extraction device (GED) and probe installation fitting
(PIF)

1 Probe in housing 650R1000

2 Probe heat
3 Probe installation fitting type 655R1010 655R1010
4 Gas extraction device length X = 150 mm/5.91" in 655R1001
Gas extraction device length X = 300 mm/11.81" in 655R1002
Gas extraction device length X = 450 mm/17.72" in 655R1003
Gas extraction device length X = 1,000 mm/39.37" in 655R1004

59
11 Appendix

Characteristics
Measurement range 0 ... 18 by Vol. %
with restriction 0 ... 21 Vol. % O2
Measurement accuracy  10 % of measured value
not more than  0,3 by Vol. %
Effect of measured gas pressure -1,6 mV / 100 mbar change
Response time t60 (60% of final value)  10 seconds
Error influences Temperature change of the measuring gas depending on the
accuracy of temperature control of the ZrO2 measuring cell
Permissible fuels Non-interacting gaseous hydrocarbons and light heating oil
direct measurement in combustion gas are not possible
Permissible continuous exhaust gas temperature  300 °C (572 °F)
Probe output voltage 0,01 ... 21 by Vol. % O2 150 ... -15 mV
Probe internal resistance RI in air at 20°C (68 °F) 15 ... 30 
and 17 W heat output
Probe voltage in air 20° C (68 °F) and 17 W heat 0 ... -15 mV
output (new probe)
Heat output at room temperature 16 ... 22 W - depending on version
Supply voltage of heating in plug Polarity is changed cyclically if PH 18 VA  11,4 V
if PH 20 VA  12,34 V
if PH 25 VA  14,8 V
Heat output for T = 350 °C (662 °F) ca.17 W
Heating current if PH 20 VA approx. 1,4 A
approx. 5A briefly during heating
PTC characteristic
Electrical connection Plug
Isolation resistance between heating and probe > 30 M
connections
Weight [g] [oz] 600 (21.2) (with housing),
290 (10.2) (without housing)
Material probe housing 1.4751/1.4301
Material connecting pipework cooper strand nickel-plated
Insulation FEP

Environmental conditions
Operating temperature Connecting cable  150 °C (302 °F)
Useful life  2 years with heating oil and natural gas
Mounting position horizontal via vertical to horizontal
Protection class DIN 40050; IP42

60
 11 Appendix

11.3 Technical Data LS2-HT Lambda Probe

Fig. 11-6 LS2-HT with flue gas bypass tube

Fig. 11-7 Dimensional drawing Lambda Probe LS2-HT (high temperature) with flue gas bypass tube

1 Lambda Probe LS2-HT high temperature type 650R1515

2 Connection head max. 100 °C (212 °F)
3 Flange seal Novaphit type 656P0263
4 Flange seal graphite type 655P4211
5 Counter flange with tube socket KTL coated type 655R0179 or
Counter flange with tube socket stainless steel 1.4571 type
6 Flue gas temperature at the probe head max. 450 °C (842 °F)
7 Abgasumlenkrohr
8 Diameter/diagonal maximum. 70 mm
9 Gas velocity:
> 1 < 10 m/s (32.81 ft/s) at a length of > 1,000 mm (39.370" in)
> 1 < 30 m/s (98.425 ft) at a length of  1,000 mm (39.370" in)
From 16 m/s (52.493 ft/s) on with increasing accuracy !
10 Length: 500 ... 2.000 mm (19.68 ... 78.74" in)
11 Hose connection 4/6 mm (0.02 in.) for calibration gas
12 Connecting cable with plug, length 2 m (6.6 ft.)

61
11 Appendix

Fig. 11-8 Dimensions of counter flange with tube socket

Technical data*
Measuring range O2: 0 ... 21 % O2
Measuring precision  10 % of measured value
 5 % of measured value after test gas calibration – not better
than  0,3 Vol. %
Sensor signal - 30 ... + 150 mV
Response time t60: < 3 s
t90: < 9 s

Response time LS2-HT with flue gas bypass t60AUR = tAUR+ t60 (see Fig. 11-9 Flue gas bypass tube delay
tube ** time as function of the velocity in the exhaust air channel
depending on the varying lengths of the flue gas bypass tube)
Relaxation time t90: < 8 s
(measurement readiness after overload)
Offset to environment < 0,3 Vol. %
Hysteresis < 1 % from measured value

Linearity < 1 % from measured value

Repeating precision < 0,1 % deviation from measured value

Ambient pressure dependency < 0,1 % from measured value (of normal pressure at sea level
in comparison with pressure at altitude of 2000 m, i.e., op -
200 mbar)

62
 11 Appendix

Technical data*
Differential pressure dependency < -1,8 mV UO2 per 100 mbar overpressure in the measuring
chamber in comparison with environment

Drift < 1,7 % from measured value (after 1000 h of operation in EL

light fuel oil and 1004 switching cycles on/off)

Cross sensitivity*** to CO2 (15 Vol. %) < 0,1 Vol. %

to CO (874 ppm) < 0,1 Vol. %
to CH4 (76 ppm) < 0,1 Vol. %
to SO2 (76 ppm) < 0,1 Vol. %
to NO (245 ppm) < 0,1 Vol. %
Humidity < 2,3 % from measured value
Influence of the installation position None if LS2 is installed according to the information in the
operating instructions.
Influence of the mains voltage None if LS2 is installed according to the information in the
operating instructions.
Influence of leakage None if LS2 is installed according to the information in the
operating instructions.
Influence of the measuring gas Change of -1,6 mV/100 mbar
Internal resistance of probe 15 … 25  (ZrO2 measuring cell in the air in case of 22 W
heating output)
Heating consumption 10 ... 25 W, (at TGas 350 °C approx. 18 W)
(according to design, measuring gas temperature and meas-
uring speed)
Supply voltage for heating AC/DC
At PH 18 VA  11,4 V
At PH 20 VA  12,34 V
At PH 25 VA  14,8 V
Heating current PH 20 VA approx. 1,6 A
approx. 5 A short term during heating
PTC characteristic
Insulation resistance < 30 M (between heating and probe connection)
Lifetime > 3 years (in case of light fuel oil and natural gas)
Weight
Probe LS2-HT 1300 g
Material of probe housing
LS2 HT 1.4571
Material connecting housing LS2-HT Aluminium
Material of connecting line Nickel-plated copper strand
FEP insulation
Operating temperature of the measuring cell 650 °C
(sensor) at 13 V heating voltage in the air (20 °C)
Measuring principle Zirconium dioxide cell (ZrO2) potentiometric (voltage probe)
Heating time 10 min until operating temperature is reached

* Information according to EN 16340:2014 D

** Test report LTC-14-IB-09-V1.0 upon request

*** O2: Information assumes an operating gas composition of 5 vol. % O2, rest is N2

63
 11 Appendix

Conditions for use

Mounting / measuring gas extraction device Directly in exhaust gas channel/ in situ
Seal tightness qL ≤ 100 cm3/h*
Mounting position Horizontal to vertical
Permissible fuels Residue-free, gaseous hydrocarbons, light fuel oil, heavy fuel
oil (HFO), lignite and coal, biomass (according to design)
Permissible exhaust gas temperature on probe < 450 °C***
head
Permissible operating temperature < 100 °C on cable lead
< 100 °C on connecting cable
Permissible storage temperature -20 ... +70 °C
Permissible measuring gas speed < 16 m/s
(higher measurement speed increases the measurement
error). Current safety measures can be deployed.
Attention:
With flue gas bypass tube length > 1 m, a high current speed
(> 30m/s) can lead to flutter and vibration of flue gas bypass
tube.
Degree of protection IP65
* According to DIN V 18160-1:2006-01 Seal tightness towards environment through housing and fastening

Fig. 11-9 Flue gas bypass tube delay time as function of the velocity in the exhaust air channel depending
on the varying lengths of the flue gas bypass tube
The figure shows the delay time tEGDT [s] resulting from the length of the flue gas bypass
tube LEGDT [mm] as a function of a flow velocity in the middle of the flue air channel v [m/s].

64
 11 Appendix

11.3.1 Terminal Assignment terminal socket for Probe HT

1 (-) Probe signal (grey)

3 (+) Probe signal (black)
4 without configuration
5 Probe heating (white)
6 Probe heating (white)

Fig. 11-10 Terminal socket LS2-HT up to

6/2015

1 (+) Probe signal (black)

2 without configuration
3 Probe heating (white)
4 Probe heating (white)
5 not equipped
6 (-) Signal (grey)

Fig. 11-11 Terminal socket LS2-HT from

6/2015

65
 11 Appendix

11.4 Electric Connections Device Side

11.4.1 Jumpers

LAMTEC SYSTEM BUS

BR101: Selection of connection resistance: 1-2 off, 2-3 on.
BR105: Position 2-3
The new processor card must also be set up for the LAMTEC SYSTEM BUS (BR12 and
BR13 in position “C“).

Digital inputs
BR106, 107: Position 1-2: Digital inputs referenced to instrument potential.
Position 2-3: Digital inputs, galvanic isolation.

11.4.2 DIP Switch

DIP switch processor card

(see illustration at 6.2.2 Monitor Output)

SW 1 SW 2 Monitor output function

OFF OFF O2 measured value 0 ... 2.5 V = 0 ... 25 % vol O2

ON OFF O2 probe voltage (U-O2) 0 ... 2.5 V = 0 ... 250 mV

OFF ON O2 cell’s internal resistance 0 ... 2.5 V = 0 ... 250 

11.4.3 Fuses

Designation Value Function

F1 1A inertial for 230 V (IEC60127-2/5) Primary fuse
2A inertial for 115 V (IEC60127-2/5)
F2 0.4 A inertial (IEC60127-2/3 or /5) Probe measuring electronics
F3 1 A inertial (IEC60127-2/3 or /5) 12 V for display background illumination
F4 1.25 A inertial (IEC60127-2/3 or /5)  5 V supply for processor card
F5 4 A inertial Probe heating and 24 V supply
from 11/2016 3,15A ultra slow fuse
F6 0.315 A inertial (IEC60127-2/3 or /5) LAMTEC SYSTEM BUS

66
 11 Appendix

11.4.4 LT2 Power Electronic Type 657E1882

Fig. 11-12 LT2 Power electronic type 657E1882

1 Transformer LT2 230/115 V change over 10 BR 106, BR 107

2 Module 1-4 Analogue outputs 11 Analogue outputs
3 Plug connector for interface modules, 12 Probe connection
e.g. RS232 in combination with interface module 13 Monitor output
4 DIP-switch 14 Analogue outputs
5 Maintenance switch 15 Relay output 1 e.g. for combined fault indication.
6 Multifunction push button switch 16 Power supply connection 230/115 V, 50/60 Hz
7 Row of LED’s for operating and status messages 17 Module 1-4
(fault/warning) Analogue inputs (voltage, current, potentiometer)
8 LAMTEC SYSTEM BUS 18 Power supply switch
9 Digital outputs (open collector) 19 Electrical connection X211 for relay module

CAUTION!
Different fuse figures F1 for 230 V and 115 V supply voltage.
Guard against supply voltage toggling!

67
 11 Appendix

11.5 Wet/Dry Measurement Deviations, Conversion Table

NOTICE
The LT2 carries out measurements directly in the humid flue gases (wet measurement). When
extractive devices are used, flue gases are removed and prepared. "Dry Measurements" are
normally used here, since the humidity has been extracted from the flue gas. As a result, O2
measurement values vary (see diagrams below).

Theoretical maximum deviations between wet and Calibration diagram and conversion table of the concentra-
dry measurement of the O2 concentration with tion values of wet (O2(n)) and dry (O2(tr)) measured oxygen
natural gas (CH4) or oil (CH2)X as fuel

O2 concentration range Constant K Gas/CH4 Constant K oil/(CH2)X

0 - 6% O2 1.18 1.115
6 - 12% O2 1.12 1.08
0 - 12% O2 1.15 1.10
Alternatively, the H2O share can be automatically calculated via a fixed factor.
To perform a liquid purification of the boiler is possible, if the probe is dismantled before. Per-
forming a liquid purification to an installed probe, can damage the probe. An error free opera-
tion is no longer possible.

NOTICE
For the liquid purification, the probe must be dismantled by all means. A liquid purification of
an installed probe will damage the probe.

68
12 Declaration of Conformity

12 Declaration of Conformity

69
12 Declaration of Conformity

70
The information in this publication is subject to technical changes.

LAMTEC Meß- und Regeltechnik

für Feuerungen GmbH & Co. KG
Wiesenstraße 6
D-69190 Walldorf
Telefon: +49 (0) 6227 6052-0 [email protected]
Telefax: +49 (0) 6227 6052-57 www.lamtec.de

Printed in Germany | Copyright  2017 Print-No. DLT6080-17-aEN-038