NOTES:

1. CONCRETE:

DEVELOP THE REQUIRED PILE JOINT STRENGTH.

DOWELS
450mm CONCRETE SHALL CONFORMTO THE REQUIREMENTSOF CLASS AA CONRETE.WITH 27.6 Mpa

DIAMETERAND LENGTHOF REINFORCINGSTEEL

DOWELS TO BE AS RECOMMENDEDBY THE
OF EPOXYRESININ ORDERTO
CYLINDER STRENGTH AND 19.0 mm. MAXIMUM AGGREGATE SIZE.

2. REINFORCEMENT:
450mm A. ALL REINFORCINGSTEELSHALLBE DEFORMEDBARSCONFORMINGTO AASHTOM31 (ASTMA615)
50

(SEE NOTE 5b)

GRADE 40.
TOP ELEV OF PILE = 65.72m 10 mmø SPACER RING BAR B. SPLICES OF ADJACENT LONGITUDINAL STEEL SHALL BE STAGGERED100 BAR DIAMETERS
APART.LENGTHOF SPLICESSHALLBE 100 mm. FOR 25 mm Ø AND1300mm FOR 28 mm Ø AND 1700
EPOXY RESIN mm. FOR 32 mm Ø.
BONDING MORTAR C. SPIRAL-TIES SHALL BE WELDED AT SPLICES.
PILE CUT-OFF LENGTH

RECEIVING HOLES SHALL

MANUFACTURER

450mm
BE 20 mm LARGER THAN 3. DRIVING
DOWELS A. PILE HEADSSHALLBE PROTECTEDFROM DIRECTIMPACT OF THE HAMMERBY CUSHION BLOCKS
1000mm

CONSISTING OF SEVERAL BLOCKS OF WOOD OR OTHER APPROVED MATERIALS.

5 @ 50 PITCH

B. PILES SHALLBE DRIVENTO A DEPTHTHAT WILL PRODUCETHE REQUIREDALLOWABLEBEARING

CAPACITY.

4. PILE FOUNDATION DESIGN

LONGITUDINAL A. IN PILE-BENT PIERS, PILE LENGTHS SHALL BE DETERMINEDBY THE ENGINEER/CONSULTANT
REINFORCEMENT
BASED ON THE ALLOWABLE PILE BEARING CAPACITY SPECIFIED BELOW.
B. IN COLUMN-BENT PIERS,THENUMBER,LOCATION AND LENGTHOF PILESSHALLBE DETERMINED

30
BY THE ENGINEER/CONSULTANT BASED ON THE LOADINGINFORMATIONGIVEN IN THE PIERS
DETAILS.
10 mmø SPIRAL ELEVATION
5. PILE SPLICE:
A. PILES MAY BE SPLICEDONLY IF STRICTLYNECESSARYAND APPROVEDBY THE ENGINEER.PILE
SPLICES SHALL BE LOCATED AT LEAST 10m BELOW THE EXISTING GROUND LEVEL.
B. PILE SPLICE SHALL DEVELOP100% AXIAL, AND 50% BENDINGOF THE CAPACITYOF THE PILE
4 PILE SPLICE DETAIL SECTION WHERE THE SPLICE IS LOCATED.
10 mmø SPIRAL

SP15 40

6. ALLOWABLE PILE BEARING CAPACITY:

750 KN. PER PILE
12000mm

BALANCE @ 100 PITCH

7. MINIMUM HAMMER ENERGY RATING

= 83 Kn-m
75 450mm TYPE OF HAMMER: HYDRAULIC HAMMER

8. BASIS FOR COMPUTING ALLOWABLE PILE BEARING CAPACITY:

167 eh Eh Wr + 0.16 Wp
120 Pall =
WELD LENGTH S + 2.54 Wr + WP
8-28 mmø
450mm

LONGITUDINAL
BARS WHERE:
Pall = ALLOWABLE PILE BEARING CAPACITY (KN)
150 eh = HAMMER EFFICIENCY
LAP LENGTH Eh = HAMMER ENERGY RATING (KN-m)
1000mm

Wr = WEIGHT OF RAM (KN)

75

Wp = WEIGHT OF PILE AND OTHER DRIVEN WEIGHTS (KN)

S = AVERAGE PENETRATION
ELEVATION
5 @ 50 PITCH

9. TEST PILES:
TEST PILES SHALLBE DRIVENWITH HYDRAULIC HAMMERUSED FOR DRIVINGREGULARPILES AND
5 MAY BE PART OF FOUNDATION IF APPROVED BY THE ENGINEER.
3 P I L E S E C T I O N
SP15 40 SCALE 1:5 3 MIN 10. PICK - UP POINTS:
IN PICK - UP POINTSSHALLBE MARKEDON ALL PILESAND ALL LIFTINGSHALL BE DONEAT THESE
50

POINTS.

300 x 300 3
0.30L 0.70L

6-32 mmø x 600

L
5 @ 50 PITCH

ANCHOR BARS

1-POINT PICK-UP
SECTION
1 P I L E E L E V A T I O N 0.21L 0.58L 0.21L
SP15 40 SCALE 1:10
50

FULL WELD
150

5 WELDED SPLICE DETAIL L

SP15 40 NOT TO SCALE
BENT PLATE
100x100x12x300 2-POINT PICK-UP
LONG

2 PILE TIP FOR HARD DRIVING THE USE OF SPECIAL EMBEDDED OR ATTACHED LIFTING DEVICES SHALL BE SUBJECT TO THE
SP15 40 SCALE 1:10 APPROVAL OF THE ENGINEER.

PROJECT NAME AND LOCATION: SHEET CONTENTS: SURVEYED: PREPARED: SUBMITTED: RECOMMENDED: APPROVED: SET NO. SHEET NO.
REPUBLIC OF THE PHILIPPINES
C.Y. 2023 PROJECT RONALD M. ABERIN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS DETAILED ENGINEERING DESIGN PLAN FOR ENGINEER II
REGION - X WIDENING OF PERMANENT BRIDGES SP 41
CAGAYAN DE ORO 1st DISTRICT ENGINEERING OFFICE ARDENT B. DAGALA JOSE MARCOS S. DACANAY EVELYN A. TIRADO ANA LEE M. MANZANO,DM,A.Er
IPONAN BRIDGE 2 (B01397MN) PILE SECTIONS AND DETAIL DRAFTED:
ENGINEER II CHIEF, PLANNING AND DESIGN SECTION ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER
10th RES Comp. Bulua, Cagayan de Oro City 15 23 57
ALONG BUTUAN CITY-CAGAYAN DE ORO CITY-ILIGAN CITY RD. ERIKA FAYE S. GUTIERREZ DATE: DATE: DATE: DATE:
CAGAYAN DE ORO CITY ENGINEER II
DATE :