Aroot Co., Ltd.
28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do ,18103, Republic of Korea
TEL +82-31-8077-5000 / FAX +82-31-624-5310 / http://www.miniprinter.com
P25 ENG Rev. C 01 / 2021
MOBILE PRINTER
MODEL � LK�P25
USER�S MANUAL
All specifications are subject to change without notice
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions.
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including
interference that may cause undesired operation.
Vic Barczyk
19700 S Vermont Ave Ste 200 Torrance, CA 90502 | USA
[email protected]Henning Mahlstedt
26188 Edewecht, Holljestr.9 | Germany
[email protected]Victor Almazan
Paseo de la Reforma No. 265 Piso 2.Oficina SBC. Col.
Cuauhtémoc, C.P. 06500 Ciudad de Mexico | Mexico
[email protected]Yan xiao rui
Room 902, No. 7, Lane 118, Xiaojishan Road, Sheshan Town,
Songjiang District, Shanghai | China
[email protected] Disposal of Old Electrical&Electronic Equipment(Applicable in
the European Union and other European countries with separate
collection systems)
This symbol on the product or on its packaging indicates that this product
shall not be treated as household waste. Instead it shall be handed over to
the applicable collection point for the recycling of electrical and electronics
equipment. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service
or the shop where you purchased the product.
Table of Contents
1. Safety Precautions 2
2. Unpacking 4
3. Product Overview 5
4. Usage and Installation 6
4-1. Control Panel Usage 6
4-2. Paper Roll Installation 7
4-3. Battery Installation 8
4-4. Charging Battery 10
4-5. Leather Case Usage 12
4-6. Self Test 13
5. Peripheral Connection 15
5-1. Bluetooth Connection 15
5-2. NFC Connection 16
5-3. Interface Cable Connection 17
6. Cleaning the Printer 18
7. JAM Error 19
8. Roll Media Specification 20
9. Black Mark 21
10. Printer Specification 22
11. Utilities 24
12. S/W 25
1. Safety Precautions
For better safety and reliability, adhere to the following precautionary measures.
Read and follow the instructions carefully before operation of the product.
Indication
Prohibition Must follow
Unplug the power from the
Do not disassemble
outlet
Grounding to prevent Do not handle the product with
electric shock wet hands
WARNING
Failure to follow these instructions could result in fire, electric shock,
other injuries, or property damage.
Do not bend the
Do not pull or
wire and do not
touch the power
allow the wire to be
plug with wet
pinched or crushed
hands.
by heavy objects.
Potential risk of
Potential risk of
electric shock or fire
electric shock or fire
If a power plug is
Do not overload broken or a plug
an electrical is cut or worn, do
outlet. not use it.
Potential risk of
Potential risk of
electric shock or fire
electric shock or fire
2
WARNING
Failure to follow these instructions could result in fire, electric shock,
other injuries, or property damage.
Do not disassemble,
repair or modify the
Do not unplug the
product.
power cable to turn
off the product. Potential risk of
malfunction, electric
Turn off the power
shock, or fire. When
using the power
the product needs to
button
be repaired, please
contact your reseller
CAUTION
Failure to follow these instructions could result in fire, electric shock,
other injuries, or property damage.
If the product
Do not install
needs to be
the product on
Dealer repaired, please
an unstable or
contact your
inclined surface.
reseller.
May cause
Potential risk of fire
damage or injury
or unit malfunction
Keep product Avoid excessive
away from the shock or drops.
water and other
Potential risk of
material. fire or property
Potential risk of fire damage
or unit malfunction
3
2. Unpacking
Standard
Printer Battery Quick Manual
Charger (USB Cable) Belt Clip (Battery Cover) Roll paper
Optional
Leather Case & Shoulder Strap
4
3. Product overview
Front
Open Button
-
Button Up: Opening the cover
USB & DC Power
Power Button
Paper Feed Button
Bottom
Battery Cover
5
4. Usage and Installation
4-1. Control Panel Usage
Button Name function
-
This button is used to turn the printer on and off.
-
When the printer is off, press this button for
Power
approximately 3 seconds and the printer will power on.
Button /
When you press this button while the printer is powered
Stand-by
on, the printer will turn off.
Button
-
When the printer is in power save mode, you can press
the button to enter Stand-by mode.
-
This button can be used to manually feed the paper.
-
Additionally, this button is also used to initiate self-
Paper tests and Hexadecimal Dumping.
Feed 01 Refer to the Self Test section of this manual for
Button information regarding self-tests.
02 Refer to the Note in Self Test section of this manual
for information regarding Hexadecimal Dumping.
-
If the Batt LED is lit, the battery is fully charged.
Battery -
If you can hear a beeping sound and LED light is
Status turned off, the battery is at the lowest level.
Lamp -
If the battery is not charged at all, the printer turns
off automatically.
Error -
If the red light is turned on, there is no paper or the
Lamp paper cover is open.
LINK/ -
LINK: LED BLINK
Power -
POWER ON: GREEN LED ON
Light -
POWER OFF: LED OFF
6
4-2. Paper Roll Installation
CAUTION
Make sure to be careful of
the HOT head.
Open Button
Press the Open button up to open Place the paper roll as shown.
the paper cover. Make sure the paper is placed in the
right direction.
1 2
3 4
CAUTION CAUTION
Please make sure you hear If the cover is not shut down
the closing sound of the completely, the printer may
upper cover. not work properly.
Pull a short length of paper out of the Tear off the additional paper using tear
printer and close the cover. bar.
7
4-3. Battery Installation
Standard
Remove the screw as shown. Open the battery cover and connect the
battery jack to the printer.
1 2
3 4
Insert the battery and close the battery Install the screw.
cover.
8
Belt Clip Battery Cover
Install in the same order as the battery cover.
NOTE
As the battery is not charged at the time of your purchase, charge the battery
prior to using the printer.
9
4-4. Charging Battery
How to charge with power cord
1 Make sure the printer is turned off.
2 After opening the DC JACK cover, connect the DC JACK to the printer.
3 Plug the power cord into the electrical outlet.
CAUTION
After opening the DC cover, pull the cover slightly.
Be careful not to pull too hard.
NOTE
01 If the charger provided by the manufacturer is not used, the printer can be
damaged, and the manufacturer is not liable for the consequential damage.
02 Before removing the battery, make sure that power is turned off.
03 When charging is completed, the power is automatically turned off.
04 The printer does not work when only connected to the charger.
05 The battery needs to be installed to operate the printer.
06 While charging, do not turn on the power.
07 Do not operate the printer while charging the battery.
08 Do not connect the charger while the printer is operating.
10
How to charge with PC
Disconnect the USB cable from the power cord adapter.
1
2
Connect the USB cable to the PC to charge the printer.
11
4-5. Leather Case Usage Optional
Open the leather case. Place the printer into the leather case.
1 2
3 4
Close the cover and press down on the Connect the shoulder strap to leather
Velcro. case rings.
12
4-6. Self Test
Turn off the power by pressing the While you are holding the FEED button,
power button for approximately 3 press the power button.
seconds.
1 2
3 4
NOTE
01 To enter hex dump mode, press
the FEED button once more.
02 If the FEED button is not pressed,
the self-test will automatically
finish after 3 seconds.
The self-test will print.
13
Self-Test Printout Sample
Upon initial installation or for
troubleshooting, you can run the
diagnostic test to get information
about:
- Firmware version, emulation,
codepage, sensor settings, interface
settings, etc.
If no issues are found with the
diagnostic test, examine other devices
and software.
The diagnostic test is working
independently of devices and software.
※ Motor protection from being
overheated
To prevent the motor from
overheating, stop the printer for at
least 30 seconds after continuously
printing 1.5 meters.
14
5. Peripheral Connection
This product can communicate with other devices via Bluetooth or a
communication cable.
5-1. Bluetooth Connection
1 The Printer can be connected to devices equipped with Bluetooth
communication capabilities(PDAs, PCs, etc.).
2 Use the Bluetooth connection function supported by your device to connect to
the printer.
NOTE
- This model supports numeric comparison function.
- Please refer to the configuration manual for details.
15
5-2. NFC Connection
The printer can be connected to devices equipped with NFC communication
capabilities.
Use the NFC connection function supported by the device to connect to the printer.
NOTE
- Please refer to the configuration manual for details.
- NFC is only compatible with Bluetooth.
16
5-3. Interface Cable Connection
USB
COVER
1 Flip over the connector cover and connect USB cable to the printer connector.
NOTE
Only use cables included with the printer. (USB)
2 Connect the interface cable to the USB port of the device (PDA, PC, etc.).
17
6. Cleaning the Printer
If the interior of the printer is dusty, printing quality can be reduced.
In this case, follow the instructions below to clean the printer.
NOTE
01 Make sure to turn the printer power off prior to cleaning.
02 Regarding printhead cleaning, as the printhead gets very hot during printing,
turn off the printer power and wait approximately 10 minutes before cleaning.
03 When cleaning the printhead, take care not to touch the heated portion of the
printhead. The printhead can be damaged by static electricity.
04 Take care not to allow the printhead to become scratched and /
or damaged in any way.
HEAD
1 Use an applicator swab moistened with an alcohol solution to clean the
printhead and remove any dust.
2 Once the cleaning is completed, wait a few minutes before inserting the paper
roll into the printer.
Preventing Overheating
To prevent the motor from overheating, stop the printer for at least 30 seconds
after continuously printing 1.5 meters.
18
7. JAM Error
CAUTION
Make sure to be careful of
the HOT head.
When you face with a paper jam error, Please remove the paper.
please press the button up to open the
printer cover.
1 2
3
NOTE NOTE
Please make sure you hear If the cover is not shut down
the closing sound of the completely, the printer may
upper cover. not work properly.
After removing, close the cover. The printer will work normally.
19
8. Roll Media Specification
Core
Diameter (A) 12.5 mm
Roll
Max.Diameter (B) 40 mm
Max.Media Width (C) 58 mm
Min.Media Thickness 0.06 mm
Protect the printhead from sand, grit, and other hard particles
during printing and storage. Keep the cover closed.
Even very small foreign particles may cause severe harm to the printhead.
20
9. Black Mark
1.8 ~ 8.3
PAPER FEEDING DIRECTION
10 ~ 58
12.5
48 (PRINT WIDTH )
5 5
58 (MAX PAPER WIDTH)
21
10. Printer Specification
Printing Method Direct Thermal
Printing Speed Max. 60mm/s
Resolution 203 DPI
FontA(12x24), FontB(9x17), Asian Font(KOR,
Character
JPN, CHN_GB2312, CHN_BIG5)
UPC-A, UPC-E, EAN-8, Code39, ITF, Codabar,
1D
Code93, Code128, EAN-13
Barcode
2D QR, PDF417, Maxicode, Datamatrix
Emulation ESC/POS Compatible
Windows Driver(10, 2012, 8, 7, 2008, VISTA, 2003,
XP, 32bit & 64bit), Window CE & Mobile Driver
Driver & SDK(CE 4.2~, Mobile 5.0~), Linux Driver, Mac
Driver, OPOS Driver, Java POS Driver, iOS SDK,
Android(2.1~) SDK, Blackberry SDK, Symbian
Sensor Paper end, Cover open, Black mark
Paper type Thermal paper
Width Max. 58 mm
Thickness 0.06 mm
Paper
Roll Max
Max. 40 mm
Diameter
Roll Core 12.5 mm ± 0.5 mm
USB, Bluetooth Smart
Interface Standard
Ready(Bluetooth4.2+BLE), NFC Tag
Battery Input AC100 ~ 240V, 50 / 60Hz
Charger Output 5V, 1A
Battery type Li-ion
Battery Output 3.7V, 2600mAh
Charging time Adaptor : 3.5 Hrs / USB : 6 Hrs
22
Size 79 x 44.4 x 103.2 [W x D x H (mm)]
Weight 189g (with battery)
Operation -10 ~ 50℃
Temperature
Storage -20 ~ 60℃
Operation 10 ~ 80%
Humidity
Storage 10 ~ 90%
23
11. Utilities
The following utilities and concerned manual can be found on the CD or homepage.
No. Name Description
This is a utility that allows you to set printers by
1 Configuration Tool interface. Detailed settings such as Wi-Fi, Ethernet, and
COM ports can be configured.
2 Download Tool(F/W) Printer's F/W and Font Download can be done.
With NVUpload running on Windows OS, you can
3 NVUpload upload and remove the bmp file as Logo in the
printer's flash memory, and print test is possible.
It is a utility app that prints text, barcodes, images,
Android Utility
4 etc. through Bluetooth and Wi-Fi communication, and
(Sewoo M_Utility)
able to printer settings.
24
12. S/W
We provides SDK, Driver, etc. as follows to respond to various S/W usage
environments.
You can download this S/W from the homepage.
No Name Description
This is an install program used to print a Mobile
1 Windows Driver
printer in Windows OS.
This is the Cups Driver used to print a Mobile printer
2 Linux Driver
in the Linux environment.
This is a driver that controls Mobile printers using the
OPOS standard.
3 OPOS Driver
It can be used after initial setting(Mobile Printer&MSR)
using the setting tool.
JavaPOS driver is an interface standard for POS
4 JavaPOS Driver software written in Java, and can be used in Mobile
Printer when printing a receipt.
This is the Cups Driver used to print a Mobile printer
5 Mac Driver
in the Mac OS environment.
Android Plugin This is a print service plug-in that allows you to print
6 (Sewoo Print Service documents, images, and web pages without installing
Plugin) additional apps.
This is library for communication and data output
7 Windows SDK
with Mobile printer in Windows OS.
This is library for communication and data output
8 Android SDK
with Mobile printers in Android OS.
This is library for communication and data output
9 iOS SDK
with Mobile printers in iOS.
25
PATENT
26
