https://truckmanualshub.

com/

BODY BUILDER INSTRUCTIONS

Mack Trucks

Cab, Instrument Panel

PI / CHU, AN / CXU, GR / GU, TD
LR, TE / MRU
Section 8
Introduction
This information provides specifications for chassis body installation for MACK vehicles.

Note: We have attempted to cover as much information as possible. However, this

information does not cover all the unique variations that a vehicle chassis may present.
Note that illustrations are typical but may not reflect all the variations of assembly.

All data provided is based on information that was current at time of release. However,
this information is subject to change without notice.
Please note that no part of this information may be reproduced, stored, or transmitted by
any means without the express written permission of MACK Trucks, Inc.

Contents:
• “AN, GR, PI DASHBOARD SWITCH LOCATIONS”, page 3

• “Overview of Instruments”, page 7

• “Instrument Cluster”, page 8

• “Gauge Layout”, page 9

• “Alarm, Check and Information Symbols”, page 15

• “Warning Indicator Light Panel”, page 17

• “Dash Switches”, page 19

• “Switch Package AUXSW-6B Assignable Body Builder Dash Mounted Rocker Switches”,
page 20

• “Lens Kit for Assignable Body Builder Switches: Part # 22392309”, page 21

• “TE/MRU Dash Panel”, page 22

• “Gauge Layout”, page 23

• “Right Hand Gauges”, page 24

• “Alarm, Check and Information Symbols”, page 26

• “Warning Indicator Light Panel”, page 28

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Page 1 (43)
All Rights Reserved
 https://truckmanualshub.com/

• “LR DASH PANEL”, page 31

• “Alarm, Check and Information Symbols”, page 33

• “Warning Indicator Light Panel”, page 34

• “PTO”, page 36

• “VECU/BBM Locations”, page 40

PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8

USA141896628 Date 3.2018 Release Page 2 (43)
 https://truckmanualshub.com/
Instrument Panel
AN, GR, PI DASHBOARD SWITCH LOCATIONS

W3133549

Panel Arrangement A and B

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 3 (43)
All Rights Reserved
 https://truckmanualshub.com/

W3133550 W3133551

Panel A Panel B

Number Part Number Description 19 82719617 FLOOR LAMP

SWITCH (non-
1 22392299 Cruise ON / OFF
gas only)
2 22392282 Cruise SET /
20 23006490 HEADLAMP
RESUME
SWITCH
3 22559210 Cummins Engine
Brake
4 22392546 Grade Gripper
Disable
5 22392314 ATC (MUD /
SNOW)
6 22393029 Trailer AUX
(CENTER PIN)
7 22396611 IGN AUX
8 22392442 DIFF LOCK (IN-
TER WHEEL)
9 22846096 INTERAXLE
LOCK
10 22392259 PLOW LAMPS
11 22559918 AIR SUSP
(DUMP)
12 22392281 STROBE
13 22392399 BATTERY AUX
14 22846105 PTO 1
15 22846105 PTO 2
16 22559226 BEACON LIGHT
17 23229511 FAN CLUTCH
OVERRIDE
18 22392285 ASSIGNABLE
ON / OFF

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 4 (43)
All Rights Reserved
 https://truckmanualshub.com/
OTHER AVAILABLE SWITCH OPTIONS

Part Number Description

22572307 LDWS DISABLE
22392308 TIME GAP (ACC)
22392420 ATC
22392256 RETARDER
22392260 ASSIGNABLE ON / OFF
22392286 WINDSHIELD DEFROST
22392297 ECS RAISE / LOWER
22392311 ASSIGNABLE MOMENTARY
22396071 POWER FLOAT
22396079 LOW HYDRA OIL OVERRIDE
22396090 SPREADER LIGHTS
22396625 REAR AMBER FLASHER
22559241 SANDER LIGHT
22559244 CHAIN LIGHT
22559245 ROTATING LIGHT
22559917 BOGIE CONTROL
22846089 TAIL GATE LOCK / UNLOCK
22846090 TAIL GATE LOCK / UNLOCK
22846091 SNOW INGESTION
22846093 NEUTRAL CONTROL
22846096 INTERAXLE
22846097 SUSP HEIGHT CONTROL
22846101 5TH WHEEL
22846108 PTO CONTROL (MUNCIE)
22846121 ECS MODE
22879194 LOAD LIGHT
23053219 FORWARD LIFT AXLE
23053220 REAR LIFT AXLE
23093324 FRONT DIFF LOCK
23093325 REAR DIFF LOCK
23229509 SHUTDOWN OVERRIDE
23229510 WINDSHIELD DEFROST
23229512 ATC
23229513 INTER WHEEL LOCK
23229514 GRADE GRIPPER DISABLE
23229515 LOW HYDRA OIL OVERRIDE
23229516 LDWS DISABLE
23229517 FRONT DIFF LOCK

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 5 (43)
All Rights Reserved
 https://truckmanualshub.com/
Part Number Description
23229518 REAR DIFF LOCK
23239140 ASSIGNABLE MOMENTARY
23239141 IGNITION (15 AMP)
23239142 REAR AMBER FLASHER

Notes

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 6 (43)
All Rights Reserved
 https://truckmanualshub.com/
Overview of Instruments
Before driving this vehicle, locate the instruments and controls, and become thoroughly familiar with their operation. After
starting and when driving, ensure that the instrument readings are normal.

W8133358

1. Air Vent 8. Infotainment Screen / Display (SID) 15. Accelerator Pedal

2. Stalk Control 9. Secondary Gauges 16. Stalk Control

3. Tachometer 10. Dash Switches 17. Brake Pedal
4. Drivers Information Display (DID) 11. Climate Control Unit 18. Steering Wheel
5. Speedometer 12. Trailer Air Supply 19. Steering Column Tilt Control Pedal
6. mDRIVE Gear Selector 13. Tractor Parking Brake 20. Steering Wheel Switches
7. Radio (SEM) 14. Trailer Hand Brake

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 7 (43)
All Rights Reserved
 https://truckmanualshub.com/
Instrument Cluster
The instrument cluster provides system/component condition information to the driver. This information is available to assist
the driver in determining any necessary actions.

The instrument cluster consists of the following components: condition indicators (tell-tales), driver information display (DID),
gauges, speedometer and tachometer, on board diagnostic (OBD) fault and warning indicators.

W8133359

1. Condition Indicators (Tell-tale)

2. Driver Information Display (DID)
3. On Board Diagnostic (OBD) Fault and Warning Indicators
4. Speedometer
5. Gauges
6. Tachometer

Notes

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 8 (43)
All Rights Reserved
 https://truckmanualshub.com/
Gauge Layout
Tachometer
The tachometer displays the engine’s revolutions per minute (RPMs).

W3133360

Speedometer
Indicates the speed of the vehicle. The speedometer is driven by the vehicle’s electronic system.

W3133361

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 9 (43)
All Rights Reserved
 https://truckmanualshub.com/
Coolant Temperature Gauge
The coolant temperature gauge indicates engine coolant temperature. The normal operating temperature for Mack engines
is 80 to 105° C (170–215° F). If the temperature remains below or exceeds the normal temperature range, the cooling sys-
tem should be checked for problems by an authorized Mack Vehicle dealer. When coolant temperature is excessive, the red
STOP tell-tale illuminates and the buzzer will sound. The engine is at risk and the ECM may derate the engine power. Stop
at the first safe place where the problem can be checked.

W3133363

Engine Oil Pressure Gauge

Indicates engine oil pressure. When the engine oil pressure is too low, the red STOP tell-tale illuminates and the buzzer will
sound. If the engine oil pressure becomes low, the engine is at risk. Bring the vehicle to a safe stop where the problem can
be checked.

DANGER
Failure to take necessary action when the STOP tell-tale is on can ultimately result in automatic engine shutdown and loss
of power steering assist. Vehicle crash can occur, resulting in personal injury or death.

W3133319

Stop Tell-Tale

W3133362

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 10 (43)
All Rights Reserved
 https://truckmanualshub.com/
Aftertreatment DEF Gauge
Indicates the amount of Diesel Exhaust Fluid (DEF) in the tank.

W3133364

Fuel Gauge
Indicates the fuel level. The fuel gauge is connected to the fuel sensor unit in the fuel tank. There is only one sensor even if
the vehicle is equipped with dual tanks.

W3133365

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 11 (43)
All Rights Reserved
 https://truckmanualshub.com/
Secondary Brake Air Pressure Gauge
The secondary brake air pressure gauge is connected to the front circuit tank via sensors mounted on the passthrough wall.
The front and rear air gauges should register equal air pressure. By observing the gauge pointers, the operator can detect a
pressure drop if an air leak develops and can readily identify the circuit affected.

DANGER
Failure to observe these precautions can result in the loss of braking performance. This can lead to a vehicle accident,
which can result in personal injury or death.

W3133366

Primary Brake Air Pressure Gauge

The primary brake air pressure gauge is connected to the rear circuit tank via sensors mounted on the passthrough wall. The
front and rear air gauges should register equal air pressure. By observing the gauge pointers, the operator can detect a pres-
sure drop if an air leak develops and can readily identify the circuit affected.

DANGER
Failure to observe these precautions can result in the loss of braking performance. This can lead to a vehicle accident,
which can result in personal injury or death.

W3133367

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 12 (43)
All Rights Reserved
 https://truckmanualshub.com/
Secondary Gauges
On certain vehicles, secondary gauges are included. These gauges are located to the right of the steering wheel, above the
main switch location.

W3133368

1. Secondary Gauges

Notes

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 13 (43)
All Rights Reserved
 https://truckmanualshub.com/
Tell-Tales
A tell-tale is a display that indicates the actuation of a de-
vice, a correct or defective condition, or a failure to
function.
The operator should become familiar with these symbols
in order to recognize and react (if necessary) to the indi-
cated condition. Tell-tale symbols are shown in the instru-
ment panel cluster.

Colors
To promote visual recognition internationally, specific col-
ors for tell-tales have been established. Unless govern-
mental regulations (in the area where the vehicle is to be
used) or engineering directives specify otherwise, the
standard colors are:

• Steady Blue — high-beam headlights

• Flashing Green — turn signals

• Flashing Red — hazard condition involving the safety

of personnel

• Steady Green — system in operation

• Steady Red — warning, immediate action required

• Amber — early warning, such as low fuel or Anti-Lock

Brake System (ABS) malfunction

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 14 (43)
All Rights Reserved
 https://truckmanualshub.com/
Alarm, Check and Information Symbols
Number Symbols Meaning

Malfunction Indi-
1
cator Lamp
W3133317

Hill Assist
2
Indicator
W3133318

3 Stop

W3133319

4 Interaxle lock
W3133320

5 Differential lock
W3133321

Turn Signal
6
Indicator
W3133322

Parking Brake
7
engaged
W3133324

Safety Belts
8
Reminder
W3133-

326

Aftertreatment
9 DPF
Regeneration
W3133327

Aftertreatment
High Exhaust
10
System
W3133328 Temperature

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 15 (43)
All Rights Reserved
 https://truckmanualshub.com/
Number Symbols Meaning Number Symbols Meaning

W3133339

ABS Malfunction
11
Trailer
W313-
Electronic Stabil-
3329
21 ity Control (ESC)
W31-
Indicator
333-

ABS Malfunction 40
12
Tractor
W3133330
Daytime Running
22 Light (DRL)
W3133341 Indicator
Preheating Ac-
13 tive or Preheat-
ing Fault Lane Changing
W3133331
23 System (LCS)
Indicator
W3133342
High Beam
14
Indicator
W3133333

24 Airbag Indicator

Aftertreatment W3133343

15 DEF Tank Low

Indicator
W3133334
Tire Pressure
Monitoring Sys-
25
tem (TPMS)
W3133344
Indicator
16 Check Indicator
W313333-

5
Automatic Trac-
26 tion Control
W31333-
(ATC)
45

17 Light Indicator

W3133336

Tractor Control
18 System (TCS)
Indicator
W3133337

Lane Departure
19 Warning System
W3- (LDWS) Indicator
133-

338

Power Take-off
20
(PTO) Indicator

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 16 (43)
All Rights Reserved
 https://truckmanualshub.com/
Warning Indicator Light Panel
1. Malfunction Indicator Lamp
Malfunction Indicator Lamp indicates government Regulation On Board Diagnostics (OBD) faults.

2. Hill Assist Indicator

Indicates hill assist is active.

3. Stop Tell-Tale
Illuminates when conditions require the driver to stop the vehicle. This usually occurs when vehicle conditions fall below des-
ignated standards for operation.

DANGER
Failure to take necessary action when the STOP tell-tale is on can ultimately result in automatic engine shutdown and loss
of power steering assist. Vehicle crash can occur, resulting in personal injury or death.

4. Interaxle Lock
Illuminates when interaxle lock is engaged.

5. Differential Lock
Illuminates when differential lock is engaged.

6. Turn Signal Indicator

Flashes when turn signals are active.

7. Parking Brake Engaged

Indicates parking brake is engaged.

8. Safety Belt Reminder

Indicates safety belt needs to be fastened.

9. Aftertreatment DPF Regeneration

Indicates aftertreatments DPF regeneration is required.

10. High Exhaust System Temperature (HEST) Indicator

The HEST Indicator illuminates when the exhaust temperature reaches 300° C (572° F) and the regeneration process be-
gins. When the regeneration process is completed, the engine should be allowed to run until the HEST indicator shuts off.

During regeneration while the vehicle is moving, the HEST indicator will only illuminate when vehicle speed is less than 8
kph (5 mph). During a parked regeneration, the HEST indicator will turn off when regeneration is complete and the exhaust
temperature has returned to a normal temperature.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 17 (43)
All Rights Reserved
 https://truckmanualshub.com/
11. ABS Trailer Malfunction
Indicates a problem being reported by the Trailer ABS System.

12. ABS Tractor Malfunction

Indicates a problem being reported by the Tractor ABS System.

13. Preheating Active

Indicates that preheating is active.

14. High Beam

Illuminates when high beam lights are engaged.

15. Aftertreatment DEF Tank Low

Illuminates when the fluid level is low. It also Flashes when the level becomes critically low.

16. Check Indicator

Illuminates when there is an engine or aftertreatment system issue.

17. Light Indicator

Illuminates when there is a lighting system error.

18. Traction Control System (TCS) Indicator

Indicates that the TCS is active.

19. Lane Departure Warning System (LDWS) Indicator

Indicates that the LDWS is off.

20. Power Take-off (PTO) Indicator

Indicates that the PTO is active.

21. Electronic Stability Control (ESC) Indicator

Indicates that the ESC system is active.

22. Daytime Running Light (DRL) Indicator

Indicates that the DRLs are active.

23. Lane Change System (LCS) Indicator

Indicates that the LCS is off or disabled.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 18 (43)
All Rights Reserved
 https://truckmanualshub.com/
24. Airbag Indicator
Indicates that there is an airbag error. Maintenance is required.

25. Tire Pressure Monitoring System (TPMS) Indicator

Indicates that there is an issue with the vehicle’s tire pressure. Maintenance is required.

26. Automatic Traction Control (ATC) Indicator

Indicates that the vehicle is losing traction and the ATC is engaging.

Dash Switches
General
Switches that may be fitted in your vehicle are on the following pages. The available switches in your particular vehicle are
dependent on the vehicle’s equipment.

Movable Switches
The location of the majority of the switches can be easily adapted to your requirements. A few switches cannot be moved for
safety reasons. Contact an authorized dealership for more information.

Switch Styles
There are three types of switches that are used on the dash panel.

Locking Standard BodyBuilder Assignable

W3133393 W3133394 W3133395

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 19 (43)
All Rights Reserved
 https://truckmanualshub.com/
Switch Package AUXSW-6B Assignable Body Builder Dash Mounted
Rocker Switches
(3) 20A, Ignition Powered, Latching On / Off (Part Number: 22396611)

(2) 15A, Ignition Powered, Latching On / Off (Part Number: 23239141)

(1) 20A, Ignition Powered, Momentary On / Off (EAXD4X) (Part Number: 22392311)

Affects: Conventional Models

When switch package option AUXSW-6B is ordered, switches will be in position #7, #12, #13, #16, #17, and #18.

W3133963

AUXSW-6B switch package is highlighted in red. The above image represents the standard installation locations. Switch lo-
cations can change based on other equipment ordered and assembly procedures.

Number Description
20A, Ignition Powered,
7
Momentary On / Off (EAXD4X)

12 15A, Ignition Powered, Latching On / Off

13 15A, Ignition Powered, Latching On / Off

16 20A, Ignition Powered, Latching On / Off

17 20A, Ignition Powered, Latching On / Off

18 20A, Ignition Powered, Latching On / Off

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 20 (43)
All Rights Reserved
 https://truckmanualshub.com/

Lens Kit for Assignable Body Builder Switches: Part # 22392309

W3133399

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 21 (43)
All Rights Reserved
 https://truckmanualshub.com/
TE/MRU Dash Panel
Dash Overview
Before driving this vehicle, locate the instruments and controls, and become familiar with their operation. After starting and
when driving, ensure that the instrument readings are normal.

W2122037

1. Light Control Panel 6. Climate Control Panel 11. Parking Brake

2. Tachometer 7. Switch Locations 12. Air Pressure Gauge
3. Tell-Tale Display 8. Brake Pedal 13. Fuel Gauge
4. Electric Horn 9. Accelerator Pedal
5. Vent 10. Ignition

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 22 (43)
All Rights Reserved
 https://truckmanualshub.com/
Gauge Layout

W3133390

1. Tachometer 4. Transmission Oil Temperature 7. Engine Oil Pressure Gauge

Gauge
2. Warning Indicator Lamps 5. Odometer / Trip Counter 8. Hour Meter
3. Speedometer 6. Voltmeter 9. Engine Coolant Temperature Gauge

1. Tachometer
Indicates engine speed in revolutions per minute (RPM). Tachometer readings should be used as a guide for shifting, as well
as to prevent engine damage due to over speed.

2. Warning Indicator Lamps

Illuminates if a status or fault indicator condition is active.

3. Speedometer
Indicates road speed in miles and/or kilometers per hour.

4. Transmission Oil Temperature Gauge

Indicates transmission oil temperature.

5. Odometer
Measures the distance traveled by the vehicle.

6. Voltmeter
Indicates the surface charge of the battery with the engine NOT running (and the ignition ON). Indicates the condition of
charging system with the engine running.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 23 (43)
All Rights Reserved
 https://truckmanualshub.com/
7. Engine Oil Pressure Gauge
Indicates engine oil pressure. The normal operating oil pressure for a Mack MP7™ engine (at governed speed) is 275.8 –
620.5 kPa (40 – 90 psi). At idling speed, the oil pressure should be 275.8 – 413.9 kPa (40 – 60 psi). Should the oil pressure
drop suddenly from the normal readings, stop the engine immediately and determine the cause.

8. Hour Meter
Indicates hours of engine operation. Hours of operation should be used as a guide for certain engine or PTO maintenance
operations.

9. Engine Coolant Temperature Gauge

Indicates the temperature of the engine coolant. The normal operating temperature for a Mack MP7™ engine is 77-107° C
(170–225° F). The driver will receive a warning if the coolant temperature reaches 106° C (223° F) and engine shutdown will
occur at 108° C (227° F) if the engine coolant temperature shut down option is enabled.

CAUTION
Avoid component damage, coolant temperate must NOT exceed 107° C (225° F).

Right Hand Gauges

W3133391

1. Air Pressure Gauge

Indicates air pressure in the air brake system. The normal operating air pressure is 759 kPa - 897 kPa (110 psi - 130 psi). If
pressure drops below 75 psi (±5 psi), the warning buzzer and warning light will go on. Determine the cause of failure before
proceeding.

2. Fuel/DEF Gauge
Registers the fuel and DEF levels in the supply tank(s).

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 24 (43)
All Rights Reserved
 https://truckmanualshub.com/
Tell-Tales
A tell-tale is a display that indicates the actuation of a de-
vice, a correct or defective condition, or a failure to
function.
The operator should become familiar with these symbols
in order to recognize and react (if necessary) to the indi-
cated condition. Tell-tale symbols are shown in the instru-
ment panel cluster.

Colors
To promote visual recognition internationally, specific col-
ors for tell-tales have been established. Unless govern-
mental regulations (in the area where the vehicle is to be
used) or engineering directives specify otherwise, the
standard colors are:

• Blue — high-beam headlights/engine maintenance

• Flashing Green — turn signals

• Flashing Red — hazard condition involving the safety

of personnel

• Steady Green — system in operation

• Steady Red — warning, immediate action required

• Amber — early warning, such as low fuel or Anti-Lock

Brake System (ABS) malfunction

CAUTION
The maximum safe oil temperature for Mack transmis-
sions is 121° C (250° F) for mineral-based oil, or 148° C
(300° F) for synthetic oil. Continued operation with oil
above this temperature will cause repaid deterioration of
the oil’s lubricating properties and is NOT recommended.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 25 (43)
All Rights Reserved
 https://truckmanualshub.com/
Alarm, Check and Information Symbols
Number Symbols Meaning

Malfunction Indi-
1
cator Lamp
W3133369

2 Wait to Start

W3133370

Electronic Mal-
3
function Indicator
W3133371

Engine Shut-
4
down Indicator
W3133372

Aftertreatment
5 DEF Tank Low
Level Indicator
W3133373

6 Grade Gripper

W3133374

Anti-Brake Sys-
7 tem Indicator
(ABS)
W3133375

Turn Signal
8
Indicator
W3133376

9 R Reverse

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 26 (43)
All Rights Reserved
 https://truckmanualshub.com/
Number Symbols Meaning Number Symbols Meaning
10 N Neutral
11 PTO Power Take Off Maintenance
25
Indicates ATC Due Indicator
12 ATC
Malfunction W3133384

Indicates low air

13 Low Air
pressure

Fuel Filter
26
High Beam Restriction
14
Indicator
W3133385
W3133377

Parking Brake Air Filter

15 27
engaged Restriction

W3133507 W3133386

Aftertreatment
16 DPF 28 Engine Oil Level
Regeneration
W3133379 W3133387

Check SCR Indicates Trans-

17 CHECK SCR
Indicator 29 Check Trans mission
Malfunction
ENGINE Engine Derate
18
DERATE Indicator Regen In
30 Regeneration
Progress
Vehicle Speed Indicates limits in
19
Limited speed
Right Hand Aftertreatment
20 RH Operation DPF
Operation 31
Regeneration
Indicates vehicle W3133388
21 Forced Neutral is in forced
neutral
Indicates engine
Change Engine Low Coolant Lev-
22 oil change is 32
Oil el Indicator
needed
W3133389

Road Stability
23
Advantage
W3133380

24 HEST Indicator

W3133381

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 27 (43)
All Rights Reserved
 https://truckmanualshub.com/
Warning Indicator Light Panel
1. Malfunction Indicator Lamp
Malfunction Indicator Lamp (MIL) indicates On Board Diagnostics (OBD) faults. Lamp remains active after repair until system
operation confirms repair.

2. Wait to Start
Indicates that the intake pre-heat is enabled. Wait to start engine until light goes out.

3. Electronic Malfunction Indicator

Illuminates when an electronic malfunction is detected.

4. Engine Malfunction Indicator

Indicates that occurrence of a condition which is required that the engine be shut down (i.e., low coolant level, low oil pres-
sure or high coolant temperature). If the engine shutdown feature is enabled, the operator has about 15 seconds after the
light goes on to pull to the side of the road before the engine shuts off. If the engine shutdown feature is disabled, the indica-
tor will function as a warning light but the engine will not shutdown.

5. Aftertreatment DEF Tank Low Indicator

Illuminates when the fluid level is low. It also Flashes when the level becomes critically low.

6. Grade Gripper
Grade Gripper provides anti-roll back assistance during the transition from a stopped position to starting on a grade.

7. Anti—Lock Brake System (ABS) Indicator

Indicates an ABS malfunction. Also illuminates momentarily as a bulb check when the ignition is turned on. If the light turns
on and stays on, a malfunction is indicated. If the light does not turn on when the ignition is turned on, the bulb and/or the
power source may be defective.
Note: When an ABS malfunction is detected, anti-lock braking in the affected wheel will be disabled and normal braking will
return; the other wheels will retain anti-lock braking.

8. Turn Signal Indicators

Flashes when turn signals are activated.

9. Reverse Indicator
Indicates that the transmission is in Reverse.

10. Neutral Indicator

Indicates that the transmission is in Neutral.

11. Power Take-Off

Indicates PTO.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 28 (43)
All Rights Reserved
 https://truckmanualshub.com/
12. Automatic Traction Control (ATC) Indicator
Indicates that ATC is operating.

13. Low Air Pressure Warning Indicator

Indicates low air pressure in the air brake system(s). This feature may also come with a buzzer.

14. High Beam Indicator

Indicates that high beams are on.

15. Parking Brake Indicator

Indicates that the parking brake is engaged.

16. Aftertreatment DPF Regeneration Required Icon

Flashes when the Diesel Particulate Filter (DPF) is becoming full / overfull and regeneration is needed.

17. Check SCR

Illuminates if a DPF Quality or Tampering fault code is active.

18. Engine Derate

Illuminates when the engine is in light or heavy DPF / DEF inducement or if derate > 20%.

19. Vehicle Speed Limited

Illuminates if speed limited via the DEF 5 mph inducement of DPF VSL function.

20. Right-Hand Operation

Indicates that a right-hand drive mode has been enabled.

21. Forced Neutral

Illuminates when PTO is engaged and the vehicle is not moving.

22. Change Engine Oil

If illuminated, immediately check the level of the engine oil.

23. Road Stability Advantage (RSA)

Blinks whenever the system is active. The tell-tale is constantly illuminated if there is a system error.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 29 (43)
All Rights Reserved
 https://truckmanualshub.com/
24. High Exhaust System Temperature (HEST) Indicator
The HEST Indicator illuminates when the exhaust temperature reaches 300° C (572° F) and the regeneration process be-
gins. When the regeneration process is completed, the engine should be allowed to run until the HEST indicator shuts off.

During regeneration while the vehicle is moving, the HEST indicator will only illuminate when vehicle speed is less than 8
kph (5 mph). During a parked regeneration, the HEST indicator will turn off when regeneration is complete and the exhaust
temperature has returned to a normal temperature.

25. Maintenance Due Indicator

Indicates that a maintenance alert has been issued (maintenance is due).

26. Fuel Filter Restriction

Illuminates when the fuel filter restriction limit is reached.

27. Air Filter Restriction

Illuminates when the air filter restriction limit is reached.

28. Engine Oil Level

If illuminated, immediately check the level of your engine oil.

29. Check Trans

Indicates transmission malfunction. Only present on vehicle equipped with automatic transmission.

30. Regen In Progress

Indicates regeneration is in progress.

31. Aftertreatment DPF Regeneration Required Icon

Illuminates when the inhibit switch is turned on. It will allow the driver to know that the switch is in the inhibit position and a re-
generation will not occur.

32. Low Coolant Level Indicator

Illuminates when the coolant level in the coolant surge tank is below the specified level. Stop and add coolant.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 30 (43)
All Rights Reserved
 https://truckmanualshub.com/
LR DASH PANEL
Overview of Instruments
Before driving this vehicle, locate the instruments and controls, and become familiar with their operation. After starting and
when driving, ensure that the instrument readings are normal.

Dash Overview

W2122036

1. Air Vent 9. Climate Control Panel 17. Transmission Oil Temperature

2. Enter / Escape for Driver Information 10. Turn Signal 18. Fuel Gauge / Diesel Exhaust Fluid
Display (DID) (DEF) Gauge
3. Cluster 11. Telescopic Steering Adjust Lever 19. Switch Location
4. Air Vent 12. Brake Pedal 20. Operating Position Selector

5. Cruise Control 13. Accelerator Pedal 21. Mirror Adjustment Knob

6. Speed Control 14. Electric Horn 22. Auxiliary Lighter
7. Park Brake 15. Manifold Pressure or Rear Axle 23. CB Radio Connector (Positive and
Gauge Negative)
8. Audio 16. Gear Selector 24. Ignition

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 31 (43)
All Rights Reserved
 https://truckmanualshub.com/
Instrument Panel Gauge Layout

W3133392

1. Engine Coolant
2. Tachometer
3. Speedometer
4. Primary Air Pressure
5. Engine Oil Pressure
6. Drivers Information Display (DID)
7. Secondary Air Pressure

Tell-Tales
A tell-tale is a display that indicates the actuation of a de-
vice, a correct or defective condition, or a failure to
function.
The operator should become familiar with these symbols
in order to recognize and react (if necessary) to the indi-
cated condition. Tell-tale symbols are shown in the instru-
ment panel cluster.

Colors
To promote visual recognition internationally, specific col-
ors for tell-tales have been established. Unless govern-
mental regulations (in the area where the vehicle is to be
used) or engineering directives specify otherwise, the
standard colors are:

• Blue — high-beam headlights/engine maintenance

• Flashing Green — turn signals

• Flashing Red — hazard condition involving the safety

of personnel

• Steady Green — system in operation

• Steady Red — warning, immediate action required

• Amber — early warning, such as low fuel or Anti-Lock

Brake System (ABS) malfunction

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 32 (43)
All Rights Reserved
 https://truckmanualshub.com/
Alarm, Check and Information Symbols
Number Symbols Meaning Number Symbols Meaning

11 PTO Power Take Off

Malfunction Indi- Indicates ATC

1 12 ATC
cator Lamp Malfunction
Indicates low air
W3133369 13 Low Air
pressure
BRAKE Emergency
14
Brake Indicator
2 Wait to Start

W3133370
Information
15
Indicator
W3133378
Electronic Mal-
3
function Indicator
W3133371
High Beam
16
Indicator
W3133377
Engine Shut-
4
down Indicator
W3133372
Parking Brake
17
Engaged
W3133507
Aftertreatment
5 DEF Tank Low
Level Indicator
Safety Belts
W3133373
Reminder
18

W3133382

6 Grade Gripper
Aftertreatment
19 DPF
W3133374
Regeneration
W3133379

Anti-Brake Sys- Aftertreatment

7 tem Indicator High Exhaust
20
(ABS) System
Temperature
W3133375 W3133381

Turn Signal
8
Indicator
W3133376

9 R Reverse
10 N Neutral

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 33 (43)
All Rights Reserved
 https://truckmanualshub.com/
Warning Indicator Light Panel
1. Malfunction Indicator Lamp
Malfunction Indicator Lamp (MIL) indicates On Board Diagnostics (OBD) faults. Lamp remains active after repair until system
operation confirms repair.

2. Wait to Start
Indicates that the intake pre-heat is enabled. Wait to start engine until light goes out.

3. Electronic Malfunction Indicator

Illuminates when an electronic malfunction is detected.

4. Engine Shutdown Indicator

Indicates that occurrence of a condition which requires that the engine be shut down (i.e., low coolant level, low oil pressure
or high coolant temperature). If the engine shutdown feature is enabled, the operator has about 15 seconds after the light
goes on to pull to the side of the road before the engine shuts off. If the engine shutdown feature is disabled, the indicator will
function as a warning light but the engine will not shutdown.

5. Aftertreatment DEF Tank Low Indicator

Illuminates when the fluid level is low. It also Flashes when the level becomes critically low.

6. Grade Gripper
Grade Gripper provides anti-roll back assistance during the transition from a stopped position to starting on a grade.

7. Anti-Lock Brake System (ABS) Indicator

Indicates an ABS malfunction. Also illuminates momentarily as a bulb check when the ignition is turned on. If the light turns
on and stays on, a malfunction is indicated. If the light does not turn on when the ignition is turned on, the bulb and/or the
power source may be defective.
Note: When an ABS malfunction is detected, anti-lock braking in the affected wheel will be disabled and normal braking will
return; the other wheels will retain anti-lock braking.

8. Turn Signal Indicators

Flashes when turn signals are activated.

9. Reverse Indicator
Indicates that the transmission is in Reverse.

10. Neutral Indicator

Indicates that the transmission is in Neutral.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 34 (43)
All Rights Reserved
 https://truckmanualshub.com/
11. Power Take-Off
Indicates PTO.

12. Automatic Traction Control (ATC) Indicator

Indicates that ATC is operating.

13. Low Air Pressure Warning Indicator

Indicates low air pressure in the air brake system(s). This feature may also come with a buzzer.

14. Emergency Brake

Indicates emergency brake is engaged.

15. Information Indicator

Indicates a malfunction. See a Mack technician if illuminated.

16. High Beam Indicator

Indicates that high beams are on.

17. Parking Brake Indicator

Indicates that the parking brake is engaged.

18. Safety Belt Indicator

Indicates that the safety belt needs to be fastened.

19. Aftertreatment DPF Regeneration

Illuminates when the inhibit switch is turned on. It notifies the driver when the switch is in inhibit position and regeneration will
not occur.

20. Aftertreatment High Exhaust System Temperature

Indicates high exhaust temperature.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 35 (43)
All Rights Reserved
 https://truckmanualshub.com/
PTO
DANGER CAUTION
A Rotating PTO shaft can snag clothes, hands, etc., It is important to only engage the switch when the PTO is
causing severe personal injury or death. To avoid injury required. Leaving the PTO pump engaged when not
or death: needed can lead to poor performance and pump
• Do NOT go near rotating shafts when the engine is damage.
running.
• STOP the engine before attempting to work on a PTO,
its controls or related equipment. Note: Some PTOs can not be operated while driving the ve-
hicle. To do so would cause component damage.
To avoid component damage, contact a certified dealer to
confirm if the vehicle’s PTO can be used while driving.

A Power Take-Off (PTO) is a device that transfers power from the engine to another piece of equipment attached to the ve-
hicle. Some examples include cement mixers and the compactor on a garbage vehicle.

A maximum of four PTOs can be operated in unison. One PTO is preset as a priority component. The remaining PTOs are
preset as secondary, third or fourth in priority. The priority settings are dependent on the PTO preset arrangement and the
number of PTOs available.

There are three basic types of PTOs available: engine-mounted, transmission-mounted, and drive shaft-mounted.

The engine-mounted PTO is direct-mounted to the engine and is engaged with a bypass valve operated by an internal
switch.

The transmission-mounted PTO is clutch-dependent, which means that operation can be regulated by depressing or re-
leasing the clutch pedal. For mDrive transmissions, this is controlled by the Transmission Electronic Control Unit (TECU). If
the vehicle has an automatic transmission the PTO operation and speed adjustment is controlled via an interior switch.

Depending on customer specification, some transmission-mounted PTOs are not operable when driving the vehicle.

The drive shaft-mounted PTO consists of an additional gearbox that divides the drive shaft into two shafts. One shaft drives
the vehicle’s axle. The other shaft drives the PTO.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 36 (43)
All Rights Reserved
 https://truckmanualshub.com/
When the PTO is engaged, the PTO tell-tale illuminates in the instrument cluster.

W3133339

PTO Tell-Tale

Use the following switch to activate/deactivate the PTO.

W3133396

PTO Switch

For manual transmissions:

1. From a parked location, depress the clutch pedal.

2. Engage the PTO by pressing the PTO switch. Press the locking tab and at the same time depress the main part of the
switch.

3. Release the clutch pedal to start the PTO.

For automatic transmissions:

1. Engage the PTO by pressing the PTO switch. Press the locking tab and at the same time depress the main part of the
switch.

The PTO engages.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 37 (43)
All Rights Reserved
 https://truckmanualshub.com/
Engine-Mounted PTO
Prior to engaging the PTO, stop the vehicle. Then run the engine at low idle or at a low speed.

1. Engage the PTO by pressing the PTO switch. Press the locking tab and at the same time depress the main part of the
switch.

The PTO is now in operation and hydraulic flow is regulated by the engine speed.

PTO Speed Adjustment

For the PTO speed adjustment to function, the Cruise Control and PTO must be activated. If the PTO can be activated while
driving the vehicle, the vehicle speed must be under approximately 8 Km/h (5 mph).

To set the engine speed:

1. Press the Cruise Control / Speed Control Switch to the ON position. This switch can be located on the steering wheel or
on the dash of the vehicle.

2. Press the PTO switch to the ON position.

The PTO is now active. The PTO revolutions per minute (RPM) automatically adjusts to the preset PTO speed.

For vehicles with the cruise control switches in the steering wheel or on the dash:

3. Press and hold the RESUME / SET or ACCEL / DECEL button to increase or decrease PTO engine speed. Then press
SET to have the PTO maintain the desired speed.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 38 (43)
All Rights Reserved
 https://truckmanualshub.com/

W3133397

1. Cruise Control Resume / Set Steering Wheel Switch

2. Cruise Control ON / OFF / Cancel Steering Wheel Switch

W3133398

Speed Control (Cruise Control) Switch

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 39 (43)
All Rights Reserved
 https://truckmanualshub.com/
VECU/BBM Locations
VECU/Body Builder Module Location for AN / PI / GR

W3133540

1. Module location behind D Panel

Body Builder Module Location for CHU / CXU / GU

W3133541

1. Module location behind the engine cover

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 40 (43)
All Rights Reserved
 https://truckmanualshub.com/
VECU Location for CHU / CXU / GU / TD

W3133542

1. VECU location behind D Panel

VECU/Body Builders Module Location for TE / MRU

W3133543

1. Module location at rear of cab on engine tunnel

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 41 (43)
All Rights Reserved
 https://truckmanualshub.com/
VECU/Body Builders Module Location for LR

W3133544

1. Module location right hand side behind lower dash panel

How to identify VECU and BBM (Vehicles Built From 1/1/2018 — Current)

W3133545
W3133546

VECU ONLY VECU / BBM

Note: BBM will have the white and orange connector plug
and the VECU will have the blue and green connector.

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 42 (43)
All Rights Reserved
 https://truckmanualshub.com/
How to identify VECU and BBM (Vehicles Built Before 12/31/2017)

W3133547 W3133548

VECU BBM

Note: BBM will have the white and orange connector plug
and the VECU will have the blue and green connector.

Notes

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU, Section 8
USA141896628 Date 3.2018 Cab, Instrument Panel Page 43 (43)
All Rights Reserved