Non-Impact 

tested – 150# C.S (Galvanised) CORROSION ALLOWANCE 0 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR INSTRUMENT AIR, PLANT AIR, UTILITY AIR PRESSURE TEST: 100 PSIG (PNEUMATIC) ASME CLASS 150 RF

AI A3A
General Engineering Services
Branch Connection Table BCT1 (Note-6)

NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2

NOMINAL DIA (mm) 15 20 25 40 50

SCHEDULE SCH. 80

WLL THICKNESS (mm) 3.73 3.91 4.55 5.08 5.54

PIPE THREADED ENDS, SMLS, ASTM-A106 GR.B,  GALVANISED (Note 1,3,5)

SCRD, ASME B16.11, FORGED STEEL, 3000#,

FITTINGS
ASTM A105N, GALVANISED (Note 5)

FLANGES ASME B16.5, 150#, SCRD. RF, ASTM A105N, GALVANISED (Note 5), SMOOTH FINISH

SPECTACLE BLIND 150#, FF, SMOOTH FINISH, ASTM A105 (GALV) TO ASME B-16.48

THREADOLET

SWAGES MSS-SP95, ASTM A234 Gr. WPB, GALVANISED BOTH ENDS THREADED MALE NPT (Note 5)

SCRD, ASME B16.11, HEX. HEADED PLUG, 3000#,

PLUGS
ASTM A105N, GALVANISED (Note 5)

JACKSCREW

SCRD, FORGED STEEL, 3000#, INTEGRAL SEATS, GROUND JOINT, ASTM-A105N,

UNIONS
GALVANISED (Note 5)

4.5mm THK, 150# ASME B16.20, 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING
GASKETS
FLEXITALLIC “CG” OR EQUAL

BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

BALL-FULL BORE
VALVES (Note 2 & 4)

BALL-RED BORE BA-57

BUTTERFLY
CHECK CH-21
GATE
GLOBE GL-26
NEEDLE
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1. Nipples to be manufactured in same material as pipe. ASME B 16.5 – Pipe Flanges and Flanged Fittings Press.
Temp (ºF)
2. For complete details of valves please refer applicable individual valve datasheets. ASME B 16.48 – Steel Line Blanks (psig)

3. Line Joints : For sizes upto 2 ” - THREADED ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded 32 to 100 285
4. Valve type selected shall be as per P&ID. ASME B-16.34 –Valves, Flanged, Threaded and Welding End
200 260
5. All galvanizing shall be by Hot Dip Galvanizing method, only as per ASTM – A123 std. ASME B31.3 – Process Piping
6. For Branching refer Appendix-C. ASME BPVC Section VIII, Div 1 & 2 – Rules for Construction of Pressure Vessels
7. Galva Coat shall be applied after welding, if any. ASME BPVC Section IX –Welding and Brazing Qualifications.
MSS SP-95 – Swage nipples and Bull Plugs

B * APR 2021 Final Issue SSP HAO HAO

A 02/03/2016 Final Issue HAO SSP SSP
Rev. Date Description By Chk. App.
 Non-Impact tested – 150# C.S With SW Fittings for 1.5” and below CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBON SERVICE PRESSURE TEST: DESIGN x 1.5 ASME CLASS 150 RF

PG, PL, FG, VA, VL, CG, DS, DO A1B
General Engineering Services
Branch Connection Table BCT1 (Note-7)                                           
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24 30
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 750
SCHEDULE SCH. 160 SCH. 80 SCH. 40 SCH. STD
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 5.54 5.49 6.02 7.11 8.18 9.27 10.31 9.53 9.53 9.53 9.53 9.53 9.53

PE, SMLS, ASTM-A106 GR.B BE, EFW ASTM A

PIPE BE, SMLS, ASTM A-106 GR.B
(Note 1,3) 672-C65 CL 12

BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS OR

SW, ASME B16.11, FORGED STEEL, 6000#, ASTM BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS, WALL
FITTINGS WELDED AND FULLY RADIOGRAPHED,
A105N THICKNESS TO MATCH PIPE
WALL THICKNESS TO MATCH PIPE

FLANGES 150#, SW. RF, SMOOTH FINISH, ASTM A105N 150#,RF WN, SMOOTH FINISH, ASTM A-105N, BORE TO MATCH PIPE

FIG 8 / SPCR & BLIND 150#, FF, SMOOTH FINISH, ASTM A516 GR 60 / 70 TO ASME B-16.48

SOCKOLET FORGED STEEL, 6000# ASTM-A105N (Note-7)

WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-7)

CAPS SW, 6000#, B16.11; ASTM- A105N
JACKSCREW ASME B 18.2.1, ASTM –A193 Gr. B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-6)
SW, FORGED STEEL, 6000#, INTEGRAL SEATS,
UNIONS
GROUND JOINT, ASTM-A105N
GASKETS 4.5mm THK, 150# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

BALL-FULL BA-76 / BA-76H

BA-7 / BA-7H (Note-9) BA-3 / BA-3H (Note-9) BA-5 / BA-5H (Note-9)
BORE (Note-9)
VALVES (Note 2 , 4 & 9)

BALL-RED BA-4 / BA-4 H (Note- BA-77 / BA-77H

BA-8 / BA-8H (Note-9) BA-6 / BA-6H (Note-9)
BORE 9) (Note-9)
BUTTERFLY
CHECK CH-26 CH-2 / CH-2A (Note-8)
GATE GA-19 GA-2
GLOBE GL-19 GL-2
NEEDLE NE-2

GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS

1.   Nipples to be manufactured in same material as pipe. ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings               Press.

Temp (ºF)
2.   For complete details of valves,  please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks (psig)

3.   Line Joints :  For sizes upto 1 ½ ”             - SOCKET WELDED ASME B 16.9 – Factory Made Wrought Butt Welding Fittings -20 to 100 285

                             For sizes  2” & above          - BUTT WELDED ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 260

4.   Valve type selected shall be as per P&ID. ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded  350 215

5.   For Welded fittings all welds shall be 100% radiographed. ASME B31.3 – Process Piping  400 200

6.    Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be provided with Jack Screw 
arrangement for the ease of removal 180° apart on one flange. Jack screw shall be procured separately while the drilling and the tapping to  ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels 500 170
match Jack Screw (as per Appendix-D) shall be done at  Site.
7.      For Branching refer Appendix-C. ASME BPVC Section IX –Welding and Brazing Qualifications.  600 140
8.       Type of check valve to be Preferably  Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check valves are required Both 
650 125
Swing/Double flanged can be used.
9. For temperature above 350 deg.F metal seated ball valve shall be used.
10. Ball valve shall be used for isolation B Apr-2021 Final Issue SSP HAO HAO

A 02/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 Impact tested for low temp. service – 150#  LTCS with SW fittings for 1.5” and below CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS AND PROPANE PRESSURE TEST: DESIGN x 1.5 ASME CLASS 150 RF

PG, PL, VL A7B
General Engineering Services
Branch Connection Table BCT1 (Note-7)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
SCHEDULE SCH. 160 SCH. 80 SCH. 40 SCH. 20 SCH. STD
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 5.54 5.49 6.02 7.11 6.35 6.35 6.35 9.53 9.53 9.53 9.53 9.53
PE, SMLS, ASTM-A333 GR.6
PIPE BE, SMLS, ASTM-A333 GR.6 BE, EFW, ASTM A671- CC65 CL12
(Note 1,3)
BW, ASTM-A420, GR. WPL 6, ASME B16.9,
SW, ASME B16.11, FORGED STEEL, 3000#, ASTM- BW, ASTM-A420, GR. WPL 6, ASME B16.9, SEAMLESS,
FITTINGS SEAMLESS OR WELDED AND FULLY
A350 LF2 CL1 WALL THICKNESS TO MATCH PIPE
RADIOGRAPHED,
FLANGES 150#, SW. RF, SMOOTH FINISH, A350 LF2 CL1 150#, RF WN, SMOOTH FINISH, ASTM-A350 LF2 CL1, BORE TO MATCH PIPE

FIG 8 / SPCR & BLIND 150#, FF, SMOOTH FINISH, ASTM A516 – 60 TO ASME B-16.48

SOCKOLET FORGED STEEL, 3000# ASTM-A350 LF2 CL1 (Note-7)

WELDOLET MSS SP-97, ASTM-A350 LF2 CL-1, SCHEDULE TO MATCH PIPE (Note-7)

CAPS ASTM-A350 LF2 CL1, SW 3000# B16.11

JACKSCREW ASME B 18.2.1, ASTM –A198 GR B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-6)

SW, FORGED STEEL, 3000#, INTEGRAL SEATS,

UNIONS
GROUND JOINT, ASTM-A350 LF2 CL1

GASKETS 4.5mm THK, 150# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
BOLTING ASTM-A-320 GR. L7 STUD BOLTS/ASTM-A194 GR. 4 NUTS
BALL-FULL
BA-70 BA-11 BA-78 BA-13
PORT
VALVES (Note 2 & 4)

BALL-RED
BA-71 BA-12 BA-79 BA-14
PORT
BUTTERFLY
CHECK CH-27 CH-5 / CH-5A (Note-8) CH-6 / CH-6A (Note-8)
GATE GA-20 GA-5
GLOBE GL-20 GL-5
NEEDLE NE-3
GENERAL NOTES: MANDATORY CODES & STANDARDS:
DESIGN LIMITS
1. Nipples to be manufactured in same material as pipe. ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings
Press.
2. For complete details of valves please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks Temp (ºF)
(psig)
3. Line Joints : For sizes upto 1 ½ ” - SOCKET WELDED ASME B 16.9 – Factory Made Wrought Butt Welding Fittings -50 to 100 285
For sizes 2” & above - BUTT WELDED ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 260
4. Valve type selected shall be as per P&ID. ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded

5. For Welded fittings all welds shall be 100% radiographed. ASME B31.3 – Process Piping

6. Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be provided with Jack Screw
arrangement for the ease of removal 180° apart on one flange. Jack screw shall be procured separately while the drilling and the tapping ASME BPVC Section VIII, Div 1 & 2 – Rules for Construction of Pressure Vessels
to match Jack Screw (per Appendix-D) shall be done at Site.
7. For Branching refer Appendix-C. ASME BPVC Section IX –Welding and Brazing Qualifications.
8. Type of check valve to be Preferably Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check valves are required Both
Swing/Double flanged can be used.
10. Ball valve shall be used for isolation
B Apr-2021 Final Issue SSP HAO HAO

A 2.3.16 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 Non-Impact tested – 150# C.S With internal coating / PE lining CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : INJECTION WATER, PRODUCED WATER PRESSURE TEST: DESIGN x 1.5 ASME CLASS 150 RF

WI, WO PIPING WITH INTERNAL COATING / LINING A1W (Note-9)

General Engineering Services
Branch Connection Table BCT1 (Note-7)
NOMINAL DIA (inch) 1/2 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24
NOMINAL DIA (mm) 15 40 50 80 100 150 200 250 300 350 400 450 500 600
SCHEDULE SCH. 160 SCH. 80 SCH. 40 SCH. STD
WALL THICKNESS (mm) 4.78 7.14 5.54 5.49 6.02 7.11 8.18 9.27 10.31 9.53 9.53 9.53 9.53 9.53

PIPE (Note – 10, 13) BE, SMLS, ASTM A-106 GR.B BE, ERW API-5L GR.B
BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS OR
FITTINGS (Note – 10, 13) BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS, WALL THICKNESS TO MATCH PIPE WELDED AND 100 % RT WALL THICKNESS TO MATCH
PIPE
FLANGES 150#,RF WN, SMOOTH FINISH, ASTM A-105N, BORE TO MATCH PIPE
SOCKOLET
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-7)
JACKSCREW ASME B 18.2.1, ASTM –A193 Gr. B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-6)
4.5mm THK, 150# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
GASKETS
(Gasket is not required if the pipe is PE lined)
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS
BALL-FULL
VALVES (Note 2, 4 & 9)

BA-3W BA-5W
BORE
BALL-RED
BA-2W/8W BA-4W BA-6W
BORE
BUTTERFLY

CHECK CH-2W/CH-2A-W

GLOBE GL-1W GL-2W

GENERAL NOTES: Notes (Contd.) DESIGN LIMITS
1. Nipples to be manufactured in same material as pipe. 14. PE lining of straight pipe spools shall be carried out by Piping Fabrication Contractor. The maximum length of spool has to be
Temp (ºF) Press. (psig)
2. For complete details of valves, please refer applicable individual valve datasheets. verified from Piping Fabrication Contractor (which has to be less than 18m due to transportation limitations).
3. Line Joints : For sizes 2” & above - BUTT WELDED 15. Bolt lengths shall be finalized after thickness of PE liner is calculated by Vendor. 32 to 100 275
4. Valve type selected shall be as per P&ID. 140 259
5. For Welded pipes and fittings all welds shall be 100% radiographed. MANDATORY CODES & STANDARDS:
6. Flanges used for Restriction Orifices of size 4” and larger shall be provided with Jack Screw arrangement for the ease of removal
180° apart on one flange. Jack screw shall be procured separately while the drilling and the tapping to match Jack Screw (as per API 6D – Flanged Valves
Appendix-D, of OMN-FAC-406) shall be done at Site.
7. For Branching refer Appendix-C of OMN-FAC-406. ASME B 16.5 – Pipe Flanges and Flanged Fittings

8. Do not use spectacle blinds or spades in lined piping. Use drop out spools (preferably near elbow) where required. ASME B 16.9 – Factory Made Wrought Butt Welding Fittings

9. “W” indicates – (a). All pipes & Fittings with Internal rotolining / internal epoxy coated or PE lined. Type of internal coaing shall be
ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded
discussed with Oxy Corrosion Engineer
10. All pipes & fittings (except 1” size) shall be procured with butt welding ends. Welding of flanges and rotolining of the fabricated
ASME B31.3 – Process Piping
assembly / spools shall be carried out by Piping Fabricator Contractor
11. For PE lined piping, annulus vent connection (1/8” dia. hole drilled on the main pipe) with flanges, gaskets and fasteners of ¾” size
ASME Section VIII – Boiler & Pressure Vessels Code, Pressure Vessels, Div 1& 2
(as per pipe class A1B) shall be provided near flange joints.
Also, backing rings shall be provided at all flanged joints. ASME Section IX –Welding Qualifications
12. PE liner thickness calculation shall be submitted by PE liner vendor for Oxy’s approval.
13. Minimum size of any process connection shall be 2"
14.Ball valve shall be used for isolation. B * APR 2021 Final Issue SP HAO HAO
A 02/03/2016 Final Issue HAO SSP SSP
Rev. Date Description By Chk. App.
 Class150 S.S 316 / 316 L (DUAL GRADE) (NOTE-6) CORROSION ALLOWANCE 0 mm PIPING SPECIFICATION

SERVICE : HYDROCARBONS  PRESSURE TEST: DESIGN X 1.5 ASME CLASS 150 RF

PL, PG & VL A2C
General Engineering Services
Branch Connection Table BCT1 (Note-5)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
SCHEDULE SCH. 40S SCH. 10S

WALL THICKNESS (mm) 2.77 2.87 3.38 3.68 2.77 3.05 3.05 3.4 3.76 4.19 4.57 4.78 4.78 4.78 5.54 6.35

PIPE BEVEL ENDS, SMLS, ASTM-A312 TP.316/316L,  (Note 1, 3)

FITTINGS BW, ASME B16.9, ASTM A403 - WP316/316L, SEAMLESS, WALL THICKNESS TO MATCH PIPE

FLANGES & BLIND ASME B16.5, 150#, WNRF, SMOOTH FINISH, ASTM A182 F316/F316L

FIG 8 / SPCR 150#, FF, SMOOTH FINISH, ASTM A240 TP316/TP316L TO ASME B-16.48

WELDOLET MSS-SP-97, ASTM A182 GR F316/F316L , BW ENDS, WALL THICKNESS TO MATCH PIPE

ASME B 18.2.1, ASTM –A193 Gr. B8 MACHINE BOLTS ,FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD
JACKSCREW
(Note-7)

GASKETS 4.5mm THK, 150# ASME B16.20, SS 316 (L) GRAPHITE SPIRAL WOUND WITH SS INNER RING / CENTERING FLEXITALLIC “CG” OR EQUAL
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS
BALL-FULL
BA-84 BA-86 BA-88
VALVES (Note

BORE
2,4,9,10,11)

BALL-RED
BA-85 BA-87 BA-89
BORE
CHECK (RF) CH-39 CH-40 / CH40A
GLOBE GL-29
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1.   Nipples to be manufactured in same material as pipe. ASME B 16.5 – Pipe Flanges and Flanged Fittings              
Press.
2.   For complete details of valves, please refer applicable individual valve datasheets. ASME B 16.48 – Steel Line Blanks Temp (ºF)
(psig)
3.   Line Joints :  For sizes  1/2” and Above   - BW ASME B 16.9 – Factory Made Wrought Butt Welding Fittings
4.   Valve type selected shall be as per P&ID.                              ASME B-16.34 –Valves, Flanged, Threaded and Welding End 32 to 100 275
5.   For Branching refer Appendix-C. ASME B31.3 – Process Piping  200 235
6. All Items shall be dual certified ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels 250 225
7.  Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be provided 
with Jack Screw arrangement for the ease of removal 180° apart on one flange. Jack screw shall be procured separately  ASME BPVC Section IX –Welding and Brazing Qualifications. 
while the drilling and the tapping to match Jack Screw (as per Appendix-D) shall be done at Site.
8. Design limits According to ASME B16.5 Flange Rating material group 2.2 MSS SP-97– Integrally Reinforced Forged – Branched Outlet Fittings
9. The use of reduced bore valve is preferred. Use full bore valves only when necessary for processing / operating 
requirements.
10. Type of check valve to be Preferably  Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check valves are 
required Both Swing/Double flanged can be used.
11. Piston type check valves for horizontal mounting only.
12. Ball Valves shall be used for isolation.
B * APR 2021 Final Issue SSP HAO HAO
A 02/03/2016 Final Issue HAO SSP SSP
Rev. Date Description By Chk. App.
 Non-Impact tested – 300# C.S with SW fittings for 1.5” & below CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS PRESSURE TEST: DESIGN x 1.5 ASME CLASS 300 RF

PG, PL, FG, DS, CG B1B
General Engineering Services
Branch Connection Table BCT1(Note-6)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
SCHEDULE SCH. 160 SCH. 80 SCH. 40 SCH. 30
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 5.54 5.49 6.02 7.11 8.18 9.27 10.31 11.13 12.7 11.13 12.7 14.27

PIPE PE, SMLS, ASTM-A106 GR.B,  (Note 1,5) BE, SMLS, ASTM A-106 GR.B BE, EFW, ASTM A672- C65 CL12

BW, ASTM-A-234, GR. WPBW, ASME B16.9,

FITTINGS SW, ASME B16.11, FORGED STEEL, 6000#, ASTM A105N BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS, WALL THICKNESS TO MATCH PIPE SEAMLESS OR WELDED AND 100% RT,
WALL THICKNESS TO MATCH PIPE

FLANGES 300#, SW. RF, SMOOTH FINISH, ASTM A105N 300#, RF WN,SMOOTH FINISH, ASTM-A-105N, BORE TO MATCH PIPE
FIG 8 / SPCR & BLIND 300#, FF, SMOOTH FINISH, ASTM A516 GR. 60 / 70 TO ASME B-16.48
SOCKOLET FORGED STEEL, 6000# ASTM-A105N (Note-6)
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-6)
CAPS SW, 6000#, B16.11 ASTM A105N
SW, FORGED STEEL 6000#, INTEGRAL SEATS, GROUND JOINT,
UNIONS
ASTM-A105N
JACKSCREW ASME B 18.2.1, ASTM –A193 Gr. B8 MACHINE BOLTS ,FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-3)
GASKETS 4.5mm THK, 300# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

BALL-FULL
BA-15 / BA-15H (Note-9) BA-17 / BA-17H (Note-9) BA-19 / BA-19H (Note-9)
VALVES (Note 2 ,4, & 9 )

BORE

BALL-RED
BA-16 / BA-16H (Note-9) BA-18 / BA-18 H (Note-9) BA-20 / BA-20H (Note-9)
BORE
BUTTERFLY
CHECK CH-28 CH-7 / CH-7A (Note-8)
GATE GA-21 GA-6
GLOBE GL-21 GL-6
NEEDLE
GENERAL NOTES: MANDATORY CODES & STANDARDS:
DESIGN LIMITS
1.  Nipples to be manufactured in same material as pipe ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings              
2.  For complete details of valves please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks Temp (ºF) Press. (psig)
3. Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be
provided with Jack Screw arrangement for the ease of removal 180° apart on one flange. Jack screw shall be ASME B 16.9 – Factory Made Wrought Butt Welding Fittings 32 to 100 740
procured separately while the drilling and the tapping to match Jack Screw (as per Appendix-D) shall be done at  
4. Valve type selected shall be as per P&ID. ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 680
5.  Line Joints :  For sizes upto 1 ½”   -SW ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded  350 645
                             For sizes 2”& above - BUTT WELDED ASME B31.3 – Process Piping  400 635
6.   For Branching refer Appendix-C. ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels 500 605
7.    For Welded fittings all welds shall be 100% radiographed. ASME BPVC Section IX –Welding and Brazing Qualifications.  600 570
8.   Type of check valve to be Preferably  Dual Plate Wafer Lug/Double Flanged except where Dissimilar  650 550
  Check valves are required Both Swing/Double flanged can be used. B * APR 2021 Final Issue SSP HAO HAO
9. . For temperature above 350 deg.F metal seated ball valve shall be used. A 02/03/2016 Final Issue HAO SSP SSP
10. Ball valves shall be used for isolation. Rev. Date Description By Chk. App.
 Non-Impact tested – 300# S.S with SW Fittings CORROSION ALLOWANCE 0 mm PIPING SPECIFICATION

SERVICE : CHEMICAL INJECTION PRESSURE TEST: DESIGN X 1.5 ASME CLASS 300 RF

CA B2B
General Engineering Services
Branch Connection Table BCT1 (Note-6)

NOMINAL DIA (inch) 1/2 3/4 1 1 1/2

NOMINAL DIA (mm) 15 20 25 40

SCHEDULE SCH. 40S SCH 10S
WLL THICKNESS (mm) 2.77 2.87 2.77 2.77
PLAIN ENDS, SMLS, ASTM-A312 GR.316,
PIPE
(Note 1,3,5)
SW, ASME B16.11, FORGED STEEL, 3000#,
FITTINGS
ASTM A182 F316
ASME B16.5, 300#, SW. RF, SMOOTH FINISH, ASTM
FLANGES
A182 F316,
300#, FF, SMOOTH FINISH, ASTM A240 TP 316 TO
FIG 8 / SPCR & BLIND
ASME B-16.48
SOCKOLET
SWAGES MSS-SP-95, ASTM A182 GR F316, SW ENDS
SW, ASME B16.11, 3000#,
CAPS
ASTM A182 GR F316
JACKSCREW
SW, FORGED SS, 3000#, INTEGRAL SEATS, GROUND
UNIONS
JOINT, ASTM-A182 F316
4.5mm THK, 300# ASME B16.20, SS 316 GRAPHITE
GASKETS SPIRAL WOUND WITH INNER RING FLEXITALLIC
“CG” OR EQUAL
ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR.
BOLTING
2H NUTS
BALL-FULL
BORE
VALVES (Note 2 & 4)

BALL-RED
BA-69
BORE
BUTTERFLY
CHECK CH-25
GATE
GLOBE
NEEDLE
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1. Nipples to be manufactured in same material as pipe. ASME B 16.5 – Pipe Flanges and Flanged Fittings
Temp (ºF) Press. (psig)
2. For complete details of valves, please refer applicable individual valve datasheets. ASME B 16.48 – Steel Line Blanks
3. Line Joints : For sizes upto 1.5 ” - SW ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded
32 to 100 720
4. Valve type selected shall be as per P&ID. ASME B-16.34 –Valves, Flanged, Threaded and Welding End
5. For Branching refer Appendix-C. ASME B31.3 – Process Piping 200 620
ASME BPVC Section VIII, Div 1 & 2 – Rules for Construction of Pressure Vessels
ASME BPVC Section IX –Welding and Brazing Qualifications.
MSS SP-95 – Swage nipples and Bull Plugs

B Apr-2021 Final Issue SSP HAO HAO

A 02/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 Non-Impact tested for t<1/2” & Impact tested for t> 1/2” - 300# C.S With SW Fittings for 1.5” and 
CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION
below sizes
SERVICE : GENERAL PIPING FOR GLYCOL SERVICE PRESSURE TEST: DESIGN x 1.5 ASME CLASS 300 RF
CG B6B
General Engineering Services
Branch Connection Table BCT1 (Note-7)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
SCHEDULE SCH. 160 SCH. 80 SCH. 40 SCH 30
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 5.54 5.49 6.02 7.11 8.18 9.27 10.31 11.13 12.7 11.13 12.7 14.27

PIPE PE, SMLS, ASTM-A106 GR.B, (Note 1,3) BE, SMLS, ASTM A-106 GR.B BE, EFW, ASTM A671 GR CC65 CL12 (Note-8)

SW, ASME B16.11, FORGED STEEL, 6000#, ASTM BW, ASTM-A420 GR. WPL6, WT. TO MATCH PIPE.
FITTINGS BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS WALL THICKNESS TO MATCH PIPE
A105N SMLS OR WELDED & 100% RT (Note-8)

FLANGES 300#, SW. RF. SMOOTH FINISH, ASTM A105N 300#, RF WN, SMOOTH FINISH, ASTM-A-105N, BORE TO MATCH PIPE
FIG 8 / SPCR & BLIND 300#, FF, SMOOTH FINISH, ASTM A516 – 60 / 70 TO ASME B-16.48

SOCKOLET FORGED STEEL, 6000# ASTM-A105N (Note-7)

WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-7)

CAPS SW, 6000# B16.11; ASTM A105N
JACKSCREW ASME B 18.2.1, ASTM –A193-B8 MACHINED BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-6)
SW, FORGED STEEL, 6000#, INTEGRAL SEATS, GROUND
UNIONS
JOINT, ASTM-A105N
GASKETS 4.5mm THK, 300# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS
BALL-FULL
BA-15 BA-17 BA-19 BA-21
BORE
VALVES (Note 2 & 4)

BALL-RED
BA-16 BA-18 BA-20 BA-22
BORE
BUTTERFLY
CHECK CH-28 CH-7 / CH-7A (Note-9) CH-8 / CH-8A (Note-9)
GATE GA-21 GA-6 GA-7
GLOBE GL-21 GL-6
NEEDLE NE-3
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1.   Nipples to be manufactured in same material as pipe. ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings               Press.
Temp (ºF)
2.    For complete details of valves  please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks (psig)

3.   Line Joints :  For sizes upto 1 ½ ”             - SOCKET WELDED ASME B 16.9 – Factory Made Wrought Butt Welding Fittings -20 to 100 740

                             For sizes  2” & above          - BUTT WELDED ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 675
4.   Valve type selected shall be as per P&ID. ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded  350 645
5.     For Welded fittings all welds shall be 100% radiographed. ASME B31.3 – Process Piping 
6.    Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be provided with Jack Screw 
arrangement for the ease of removal 180° apart on one flange. Jack screw shall be procured separately while the drilling and the tapping to  ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels
match Jack Screw (as per Appendix-D) shall be done at  Site.
7.    For Branching refer Appendix-C. ASME BPVC Section IX –Welding and Brazing Qualifications. 

8.   Depending on Project requirement, Carbon Steel material with impact testing certification can be used in place of LTCS.

9.   Type of check valve to be Preferably  Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check valves are required Both 
Swing/Double flanged can be used.
10. Ball valves shall be used for isolation B Apr-2021 Final Issue SSP HAO HAO

A 02/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 Impact tested for low temp. service – 300# C.S with SW fittings for 1.5” and below sizes CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS AND PROPANE PRESSURE TEST: DESIGN x 1.5 ASME CLASS 300 RF

PG, PL B7B
General Engineering Services
Branch Connection Table BCT1 (Note-7)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
SCHEDULE SCH. 160 SCH. 80 SCH. 40 SCH 30
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 5.54 5.49 6.02 7.11 8.18 9.27 10.31 11.13 12.7 11.13 12.7 14.27
PE, SMLS, ASTM-A333 GR.6
PIPE BE, SMLS, ASTM-A333 GR.6 EFW,BE,ASTM A671-CC65 CL12
(Note 1,3)
BW, ASTM-A420, GR. WPL 6, ASME B16.9,
SW, ASME B16.11, FORGED STEEL, 6000#, ASTM-A350 LF2 BW, ASTM-A420, GR. WPL 6, ASME B16.9, SEAMLESS, WALL THICKNESS TO SEAMLESS OR WELDED AND FULLY
FITTINGS
CL1 MATCH PIPE RADIOGRAPHED,
WALL THICKNESS TO MATCH PIPE

FLANGES 300#, SW. RF, SMOOTH FINISH, A350 LF2 CL1 300#, RF WN, SMOOTH FINISH, ASTM-A350 LF2 CL1, BORE TO MATCH PIPE

FIG 8 / SPCR & BLIND 300#, FF, SMOOTH FINISH, ASTM A516 – 60 / 70 TO ASME B-16.48

SOCKOLET FORGED STEEL, 6000# ASTM-A350 LF2 (Note-7) CL1

WELDOLET MSS SP-97, ASTM-A350 LF2 CL1, SCHEDULE TO MATCH PIPE (Note-7)

CAPS ASTM-A350 LF2 CL1, SW 6000# B16.11

JACKSCREW ASME B 18.2.1, ASTM –A193 Gr. B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-6)
SW, FORGED STEEL, 6000#, INTEGRAL SEATS, GROUND
UNIONS
JOINT, ASTM-A350 LF2 CL1
GASKETS 4.5mm THK, 300# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
BOLTING ASTM-A-320 L7 STUD BOLTS/A194-Gr 4 NUTS
BALL-FULL
BA-60 BA-27 BA-21
VALVES (Note 2 & 4)

BORE
BALL-RED
BA-61 BA-28 BA-22
BORE
CHECK CH-29 CH-10 / CH-10A (Note-8) CH-11 / CH-11A (Note-8)
GATE GA-22 GA-7
GLOBE GL-22 GL-7
NEEDLE NE-5
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1. Nipples to be manufactured in same material as pipe. ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings Press.
Temp (ºF)
2. For complete details of valves please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks (psig)

3. Line Joints : For sizes upto 1 ½ ” - SW ASME B 16.9 – Factory Made Wrought Butt Welding Fittings -50 to 100 740
For sizes 2” & above - BUTT WELDED ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 680
4. Valve type selected shall be as per P&ID. ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded
5. For Welded fittings all welds shall be 100% radiographed. ASME B31.3 – Process Piping

6. Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be provided with Jack Screw arrangement for the ease of
removal 180° apart on one flange. Jack screw shall be procured separately while the drilling and the tapping to match Jack Screw (as per Appendix-D) shall be done at ASME BPVC Section VIII, Div 1 & 2 – Rules for Construction of Pressure Vessels
Site.

7. For Branching refer Appendix-C. ASME BPVC Section IX –Welding and Brazing Qualifications.
8. Type of check valve to be Preferably Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check valves are required Both Swing/Double flanged can be
used.
9. ball valve shall be used for isolation.

B Apr-2021 Final Issue SSP HAO HAO

A 02/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 Non-Impact tested – 300# C.S With internal coating / PE lining CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : INJECTION WATER, PRODUCED WATER PRESSURE TEST: DESIGN x 1.5 ASME CLASS 300 RF

WI, WO PIPING WITH INTERNAL COATING / LINING B1W (Note-9)

General Engineering Services
Branch Connection Table BCT1 (Note-7)
NOMINAL DIA (inch) 2 3 4 6 8 10 12 14 16 18 20 24
NOMINAL DIA (mm) 50 80 100 150 200 250 300 350 400 450 500 600
SCHEDULE SCH. 80 SCH. 40 SCH 30
WALL THICKNESS (mm) 5.54 5.49 6.02 7.11 8.18 9.27 10.31 11.13 12.7 11.13 12.7 14.27
PIPE (Note – 10, 13) BE, SMLS, ASTM A-106 GR.B BE, ERW API-5L GR.B
BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS, WALL THICKNESS TO BW, ASTM-A-234, GR. WPB, ASME B16.9,
FITTINGS (Note – 10, 13)
MATCH PIPE SEAMLESS OR WELDED AND 100 % RT WALL
FLANGES 300#,RF WN, SMOOTH FINISH, ASTM A-105N, BORE TO MATCH PIPE
SOCKOLET
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-7)
JACKSCREW ASME B 18.2.1, ASTM –A193 Gr. B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-6)
UNIONS
4.5mm THK, 300# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
GASKETS
(Gasket is not required if the pipe is PE lined)
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS
BALL-FULL
VALVES (Note 2,

BA-17W
BORE
BALL-RED
4 & 9)

BA-18W BA -20W
BORE
CHECK CH-7-W/CH-7A-W
GL-6-W
GENERAL NOTES: Notes (Contd.) DESIGN LIMITS
1.   Nipples to be manufactured in same material as pipe. 13. PE lining of straight pipe spools shall be carried out by Piping Fabrication Contractor. The maximum length Press.
 of spool has to be verified from Piping Fabrication Contractor (which has to be less than 18m due to transportation  Temp (ºF)
2.   For complete details of valves please refer applicable individual valve datasheets. (psig)
limitations).
3.   Line Joints :  For sizes  2” & above          - BUTT WELDED 14. Bolt lengths shall be finalized after thickness of PE liner is calculated by Vendor. 32 to 100 720
4.   Valve type selected shall be as per P&ID. 140 680
5.   For Welded pipes and fittings all welds shall be 100% radiographed. MANDATORY CODES & STANDARDS:
6.    Flanges used for Restriction Orifices of size 4” and larger shall be provided with Jack Screw arrangement for the 
ease of removal 180° apart on one flange. Jack screw shall be procured separately while the drilling and the tapping  API 6D – Flanged Valves
to match Jack Screw (as per Appendix-D, of OMN-FAC-406) shall be done at Site.
7.      For Branching refer Appendix-C of OMN-FAC-406. ASME B 16.5 –  Pipe Flanges and Flanged Fittings             
8.       Do not use spectacle blinds or spades in lined piping. Use drop out spools (preferably near elbow) where 
ASME B 16.9 – Factory Made Wrought Butt Welding Fittings
required. 
9. “W” indicates – (a). All pipes & Fittings with Internal rotolining / internal epoxy coated or PE lined. Type of internal 
ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded
coating shall be discussed with Oxy corrosion engineer
10. All pipes & fittings (except 1” size) shall be procured with butt welding ends. Welding of flanges and rotolining of 
ASME B31.3 – Process Piping 
the fabricated assembly / spools shall be carried out by Piping Fabricator Contractor
11. For PE lined piping, annulus vent connection (1/8” dia. hole drilled on the main pipe) with flanges, gaskets and 
ASME Section VIII – Boiler & Pressure Vessels Code, Pressure Vessels, Div 1& 2
fasteners of ¾” size (as per pipe class B1B) shall be provided near flange joints.
Also, backing rings shall be provided at all flanged joints. ASME Section IX –Welding Qualifications
12. PE liner thickness calculation shall be submitted by PE liner vendor for Oxy’s approval.
14.Ball valve shall be used for isolation.
B * APR 2021 Final Issue ssp SP HAO
A 03/03/2016 Final Issue HAO SSP SSP
Rev. Date Description By Chk. App.
 Class 300 S.S 316 / 316 L (DUAL GRADE) (NOTE-6) CORROSION ALLOWANCE 0 mm PIPING SPECIFICATION

SERVICE : HYDROCARBONS  PRESSURE TEST: DESIGN X 1.5 ASME CLASS 300 RF

PL, PG & VL B2C
General Engineering Services
Branch Connection Table BCT1 (Note-5)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
SCHEDULE SCH. 40S SCH. 30
WALL THICKNESS (mm) 2.77 2.87 2.77 3.68 3.91 5.49 6.02 7.11 7.04 7.8 8.38 9.53 9.53 11.13 12.7 14.27
BEVEL ENDS, WELDED, ASTM-A358 TP 316 / 316L,
PIPE BEVEL ENDS, SMLS, ASTM-A312 TP.316/316L,  (Note 1, 3)
(Note 1, 3)
BW, ASME B16.9, ASTM A403 - WP316/316L, SEAMLESS OR
FITTINGS BW, ASME B16.9, ASTM A403 - WP316/316L, SEAMLESS, WALL THICKNESS TO MATCH PIPE
WELDED, WALL THICKNESS TO MATCH PIPE
FLANGES & BLIND ASME B16.5, 300#, WNRF, SMOOTH FINISH, ASTM A182 F316 / 316L
FIG 8 / SPCR 300#, FF, SMOOTH FINISH, ASTM A240 TP 316/316L TO ASME B-16.48
WELDOLET MSS-SP-97, ASTM A182 GR F316/316L , BW ENDS, WALL THICKNESS TO MATCH PIPE
JACKSCREW ASME B 18.2.1, ASTM –A193 Gr. B8 MACHINE BOLTS ,FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-7)
GASKETS 4.5mm THK, 300# ASME B16.20, SS 316 (L) GRAPHITE SPIRAL WOUND WITH SS INNER RING / CENTERING FLEXITALLIC “CG” OR EQUAL
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

BALL-FULL
BA-90 BA-94
VALVES (Note

BORE
2,4,9,10,11)

BALL-RED
BA-91 BA-95
BORE

CHECK (RF) CH-41 CH-42 / CH-42A

GLOBE GL-30
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1.   Nipples to be manufactured in same material as pipe. ASME B 16.5 – Pipe Flanges and Flanged Fittings               Temp Press.
2.   For complete details of valves, please refer applicable individual valve datasheets. ASME B 16.48 – Steel Line Blanks (ºF) (psig)
32 to
3.   Line Joints :  For sizes  1/2” and Above   - BW ASME B 16.9 – Factory Made Wrought Butt Welding Fittings 720
100
4.   Valve type selected shall be as per P&ID.                              ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 620
5.   For Branching refer Appendix-C. ASME B31.3 – Process Piping  300 560
6. All Items shall be dual certified ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels
7.  Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be provided 
with Jack Screw arrangement for the ease of removal 180° apart on one flange. Jack screw shall be procured  ASME BPVC Section IX –Welding and Brazing Qualifications. 
separately while the drilling and the tapping to match Jack Screw (as per Appendix-D) shall be done at Site.
8. Design limits According to ASME B16.5 Flange Rating material group 2.2 MSS SP-97– Integrally Reinforced Forged – Branched Outlet Fittings
9. The use of reduced bore valve is preferred. Use full bore valves only when necessary for processing / operating 
requirements.
10. Type of check valve to be Preferably  Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check valves 
are required Both Swing/Double flanged can be used.
11. Piston type check valves for horizontal mounting only.
12. Ball Valves shall be used for isolation.
B * APR 2021 Final Issue SSP HAO HAO

A 03/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 Non-Impact tested C.S – 600# (with SW fittings for 1 ½” and below) CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS PRESSURE TEST: DESIGN x 1.5 ASME CLASS 600 RF

PG, PL, PH, FG, CG D1B
General Engineering Services
Branch Connection Table BCT1(Note-6)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
SCHEDULE SCH. 160 SCH. 80 SCH 60
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 5.54 7.62 8.56 10.97 12.7 15.09 17.48 19.05 21.44 19.1 20.62 24.61
BE,EFW,ASTM A672 C65
PIPE PE, SMLS, ASTM-A106 GR.B  (Note 1,5) BE, SMLS, ASTM A-106 GR.B
CL22
BW, ASTM-A-234, GR. WPBW,
ASME B16.9, SEAMLESS OR
FITTINGS SW, ASME B16.11, FORGED STEEL, 6000#, ASTM A105N BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS, WALL THICKNESS TO MATCH PIPE
WELDED AND FULLY
RADIOGRAPHED,
FLANGES 600#, SW. RF, SMOOTH FINISH, ASTM A105N 600#, RF WN, SMOOTH FINISH, ASTM-A-105N, BORE TO MATCH PIPE
FIG 8 / SPCR & BLIND 600#, FF, SMOOTH FINISH, ASTM A516 – 60 / 70 TO ASME B-16.48
SOCKOLET FORGED STEEL, 6000# ASTM-A105N (Note-6)
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-6)
CAPS SW, 6000# B 16.11 ASTM A105N
SW, FORGED STEEL , 6000#, INTEGRAL SEATS, GROUND
UNIONS
JOINT, ASTM-A105N
JACKSCREW ASME B 18.2.1, ASTM –A193-B8 MACHINED BOLTS, FULL LENGTH UNC THREAD WITH HEX HEAD (Note-3)
GASKETS 4.5mm THK, 600# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

BALL-FULL
BA-29 / BA-29H (Note-9) BA-31 / BA-31H (Note-9) BA-33 / BA-33H (Note-9)
BORE
VALVES (Note 2 ,4, & 9 )

BALL-RED
BA-30 / BA-30H (Note-9) BA-32 / BA-32H (Note-9) BA-34 / BA-34H (Note-9)
BORE
BUTTERFLY

CHECK CH-30 CH-12 / CH-12A (Note-8)

GATE GA-23 GA-10
GLOBE GL-23 GL-8
NEEDLE
MANDATORY CODES & STANDARDS:
GENERAL NOTES: DESIGN LIMITS
ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings              
1.  Nipples to be manufactured in same material as pipe ASME B 16.48– Steel Line Blanks Temp (ºF) Press. (psig)
2.  For complete details of valves please refer applicable individual valve datasheets. ASME B 16.9 – Factory Made Wrought Butt Welding Fittings 32 to 100 1480
3.  Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 6” and larger 
200 1360
shall be provided with Jack Screw arrangement for the ease of removal 180° apart on one flange. 
ASME B-16.34 –Valves, Flanged, Threaded and Welding End
Jack screw shall be procured separately while the drilling and the tapping to match Jack Screw (as 
350 1287.5
per Appendix-D) shall be done at  Site.
4. Valve type selected shall be as per P&ID. ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded  400 1265
5.  Line Joints :  For sizes upto 1 ½”   - SW ASME B31.3 – Process Piping  500 1205
                             For sizes 2”& above - BUTT WELDED ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels 600 1135
6.   For Branching refer Appendix-C. ASME BPVC Section IX –Welding and Brazing Qualifications.  650 1100
7.   For Welded fittings all welds shall be 100% radiographed. 650 1100
8.    Type of check valve to be Preferably  Dual Plate Wafer Lug/Double Flanged except where 
Dissimilar Check valves are required Both Swing/Double flanged can be used.
9. . For temperature above 350 deg.F metal seated ball valve shall be used. B * APR 2021 Final Issue SSP HAO HAO

10. Ball Valves shall be used for isolation. A 03/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 Non-Impact tested for t<1/2” & Impact tested for t> 1/2” - 600# C.S With SW Fittings for 1.5” and below sizes CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR GLYCOL SERVICE PRESSURE TEST: DESIGN x 1.5 ASME CLASS 600 RF

CG D6B
General Engineering Services
Branch Connection Table BCT1 (Note-7)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
SCHEDULE SCH. 160 SCH. 80 SCH 60
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 5.54 7.62 8.56 10.97 12.7 15.09 17.48 19.05 21.44 19.05 20.62 24.61
BE, EFW, ASTM A671 GRCC65 CL22
PIPE PE, SMLS, ASTM-A106 GR.B, (Note 1,3) BE, SMLS, ASTM A-106 GR.B BE, SMLS, ASTM – A333 GR.6 (Note-8)
(Note-8)

BW, ASTM-A420 GR. WPL6, WT. TO

BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS, WT TO
FITTINGS SW, ASME B16.11, FORGED STEEL, 6000#, ASTM A105N BW, ASTM-A420 GR. WPL6, SEAMLESS, WALL THICKNESS TO MATCH PIPE MATCH PIPE, SEAMLESS OR WELDED
MATCH PIPE
& FULL RADIOGRAPHED

FLANGES 600#, SW. RF. SMOOTH FINISH,ASTM A105N 600#, RF WN, SMOOTH FINISH, ASTM-A-105N, BORE TO MATCH PIPE
FIG 8 / SPCR & BLIND 600#, FF, SMOOTH FINISH, ASTM A516 – 60 / 70 TO ASME B-16.48
SOCKOLET FORGED STEEL, 6000# ASTM-A105N (Note-7)
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-7)
CAPS SW, 6000# B16.11; ASTM A105N
JACKSCREW ASME B 18.2.1, ASTM –A193-B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-6)
SW, FORGED STEEL, 6000#, INTEGRAL SEATS, GROUND JOINT,
UNIONS
ASTM-A105N

GASKETS 4.5mm THK, 600# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL

BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

BALL-FULL
BA-29 BA-31 BA-33 BA-35
BORE
VALVES (Note 2 & 4)

BALL-RED
BA-30 BA-32 BA-34 BA-36
BORE
BUTTERFLY
CHECK CH-30 CH-12 / CH-12A (Note-9) CH-13 / CH-13A (Note-9)
GATE GA-23 GA-10 GA-11
GLOBE GL-23 GL-8 GL-9
NEEDLE NE-4
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1.   Nipples to be manufactured in same material as pipe. ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings              
Temp (ºF) Press. (psig)
2.    For complete details of valves  please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks
3.   Line Joints :  For sizes upto 1 ½ ”            - SOCKET WELDED ASME B 16.9 – Factory Made Wrought Butt Welding Fittings -20 to 100 1480
                             For sizes  2” & above          - BUTT WELDED ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 1360
4.   Valve type selected shall be as per P&ID. ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded  350 1287.5
5.     For Welded fittings all welds shall be 100% radiographed. ASME B31.3 – Process Piping 
6.    Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be provided with Jack Screw arrangement for the ease 
ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels
of removal 180° apart on one flange. Jack screw shall be procured separately while the drilling and the tapping to match Jack Screw (as per Appendix-D) shall be 
7.      For Branching refer Appendix-C. ASME BPVC Section IX –Welding and Brazing Qualifications. 
8.     Depending on Project requirement, Carbon Steel material with impact testing certification can     be used in place of LTCS.
9.    Type of check valve to be Preferably  Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check valves are required Both Swing/Double flanged 
can be used.
10. Ball valves shall be used for isolation.

B * APR 2021 Final Issue SSP HAO HAO

A 03/03/2016 Final Issue HAO SSP SSP

Rev Date Description By Chk. App.

 Impact tested for low temperature service - 600# C.S with SW fittings for 1.5” and below sizes CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS PRESSURE TEST: DESIGN x 1.5 ASME CLASS 600 RF

PG,VL D7B
General Engineering Services
Branch Connection Table BCT1(Note-7)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16 18 20 24
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
SCHEDULE SCH. 160 SCH. 80 SCH. 60
WALL THICKNESS (mm) 4.77 5.56 6.35 7.14 5.54 7.62 8.56 10.97 12.7 15.06 17.48 19.05 21.41 19.05 20.62 24.61
PE, SMLS, ASTM A-333 GR.6,
PIPE BE, SMLS, ASTM A-333 GR.6 BE, EFW, ASTM A671 GRCC65 CL22
(Note 1,3)

BW, ASME B 16.9, ASTM-A-420, GR. WPL-6,

SW, ASME B16.11, FORGED STEEL, 6000#,  ASTM-A350 GR. WALL THICKNESS TO MATCH PIPE,
FITTINGS BW, ASME B 16.9, ASTM-A-420, GR. WPL 6, SEAMLESS, WALL THICKNESS TO MATCH PIPE
LF2 CL1 SEAMLESS OR WELDED AND FULLY
RADIOGRAPHED

FLANGES 600#, SW. RF,  SMOOTH FINISH, A350 GR. LF2 CL1 600#, RF WN, SMOOTH FINISH, ASTM-A350 GR. LF2 CL1, BORE TO MATCH PIPE
FIG 8 / SPCR & BLIND 600#, FF, SMOOTH FINISH, ASTM A516 – 60 / 70 TO ASME B-16.48

SOCKOLET FORGED STEEL, 6000#  ASTM-A350 GR. LF2 CL1(Note-7)

MSS-SP97,  ASTM-A350 GR. LF2 CL1, SCHEDULE TO MATCH PIPE

WELDOLET
(Note-7)
CAPS SW, 6000# B16.11,  A350 GR. LF2 CL1
JACKSCREW ASME B 18.2.1, ASTM A-A193-B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-6)
SW, FORGED STEEL 6000#, INTEGRAL SEATS, GROUND JOINT,
UNIONS
ASTM-A350 GR. LF2 CL1
GASKETS 4.5mm THK, 600# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
BOLTING ASTM-A-320 GR.L7 STUD BOLTS W/ASTM-A194 GR. 4 NUTS
BALL-FULL
BA-23 BA-25 BA-35
BORE
VALVES (Note 2&4 )

BALL-RED
BA-24 BA-26 BA-36
BORE
BUTTERFLY
CHECK CH-31 CH-36 & CH-36A
GATE GA-24
GLOBE GL-24
NEEDLE
GENERAL NOTES: MANDATORY CODES & STANDARDS:
DESIGN LIMITS
1.   Nipples to be manufactured in same material as pipe. ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings              
2.   For complete details of valves  please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks Temp (ºF) Press. (psig)
3.   Line Joints :  For sizes upto 1 ½ ”             - SW ASME B 16.9 – Factory Made Wrought Butt Welding Fittings -50 to 100 1480
                             For sizes  2” & above          - BUTT WELDED ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 1360
4.   Valve type selected shall be as per P&ID. ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded 
5.     For Welded fittings all welds shall be 100% radiographed. ASME B31.3 – Process Piping 
6. Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall
be provided with Jack Screw arrangement for the ease of removal 180° apart on one flange. Jack screw shall 
ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels
be procured separately while the drilling and the tapping to match Jack Screw (as per Appendix-D) shall be
done at  Site.
7.      For Branching refer Appendix-C. ASME BPVC Section IX –Welding and Brazing Qualifications. 
8. Ball valves shall be used for Isolation.

B * APR 2021 Final Issue SSP HAO HAO

A 03/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 Non-Impact tested – 600# C.S With internal coating / PE lining CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : INJECTION WATER, PRODUCED WATER PRESSURE TEST: DESIGN x 1.5 ASME CLASS 600 RF

WI, WO PIPING WITH INTERNAL COATING / LINING D1W (Note-9)

General Engineering Services
Branch Connection Table BCT1 (Note-7)
NOMINAL DIA (inch) 1/2 1 2 3 4 6 8 10 12
NOMINAL DIA (mm) 15 25 50 80 100 150 200 250 300
SCHEDULE SCH. 160 SCH. 80
WALL THICKNESS (mm) 4.78 6.35 5.54 7.62 8.56 10.97 12.7 15.09 17.48
PIPE (Note – 10, 13) BE, SMLS, ASTM A-106 GR.B

FITTINGS (Note – 10, 13) BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS,

FLANGES 600#,RF, SMOOTH FINISH, ASTM A-105N, BORE TO MATCH PIPE

WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-7)
ASME B 18.2.1, ASTM –A193 Gr. B8 MACHINE BOLTS,
JACKSCREW
FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-6)
4.5mm THK, 600# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL (Gasket is not required if the pipe 
GASKETS
is PE lined)
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS
VALVES (Note 2, 4

BALL-FULL
BA-31-W BA-33-W
BORE
BALL-RED
& 9)

BA-30 W BA-32-W BA-34-W

BORE
CHECK CH-12-W
GLOBE GL-8-W
GENERAL NOTES: Notes (Contd.) DESIGN LIMITS
1.   Nipples to be manufactured in same material as pipe. 13. PE lining of straight pipe spools shall be carried out by Piping Fabrication Contractor. 
The maximum length of spool has to be verified from Piping Fabrication Contractor (which has to be less than 18m due  Temp (ºF) Press. (psig)
2.   For complete details of valves, please refer applicable individual valve datasheets.
to transportation limitations).
3.   Line Joints :  For sizes  2” & above          - BUTT WELDED 14. Bolt lengths shall be finalized after thickness of PE liner is calculated by Vendor. 32 to 100 1140
4.   Valve type selected shall be as per P&ID. 15. Minimum process connection shall be 2" 140 1360
5.   For Welded pipes and fittings all welds shall be 100% radiographed. MANDATORY CODES & STANDARDS:
6.    Flanges used for Restriction Orifices of size 4” and larger shall be provided with Jack Screw arrangement for 
the ease of removal 180° apart on one flange. Jack screw shall be procured separately while the drilling and the  API 6D – Flanged Valves
tapping to match Jack Screw (as per Appendix-D) shall be done at Site.

7.      For Branching refer Appendix-C. ASME B 16.5 –  Pipe Flanges and Flanged Fittings             

8.Do not use spectacle blinds or spades in lined piping. Use drop out spools (preferably near elbow) where 
ASME B 16.9 – Factory Made Wrought Butt Welding Fittings
required. 
9. “W” indicates – (a). All pipes & Fittings with Internal rotolining / internal epoxy coated or PE lined. Type of 
ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded
internal coating shall be discussed with Oxy corrosion engineer
10. All pipes & fittings (except 1” size) shall be procured with butt welding ends. Welding of flanges and rotolining 
ASME B31.3 – Process Piping 
of the fabricated assembly / spools shall be carried out by Piping Fabricator Contractor

11. For PE lined piping, annulus vent connection (1/8” dia. hole drilled on the main pipe) with flanges, gaskets and 
ASME Section VIII – Boiler & Pressure Vessels Code, Pressure Vessels, Div 1& 2
fasteners of ¾” size (as per pipe class D1B) shall be provided near flange joints.

Also, backing rings shall be provided at all flanged joints. ASME Section IX –Welding Qualifications

12. PE liner thickness calculation shall be submitted by PE liner vendor for Oxy’s approval.

B * APR 2021 Final Issue SSP HAO HAO

A 03/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By CHk APP

 Class 600 S.S 316 / 316 L (DUAL GRADE) (NOTE-6) CORROSION ALLOWANCE 0 mm PIPING SPECIFICATION

SERVICE : HYDROCARBONS  PRESSURE TEST: DESIGN X 1.5 ASME CLASS 600 RF

PL, PG & VL D2C
General Engineering Services
Branch Connection Table BCT1 (Note-5)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300
SCHEDULE SCH. 40S SCH. 80S(Note:13)
WALL THICKNESS (mm) 2.77 2.87 3.38 3.68 3.91 5.49 6.02 7.11 12.7 12.7 12.7

PIPE BEVEL ENDS, SMLS, ASTM-A312 TP.316/316L,  (Note 1, 3)

FITTINGS BW, ASME B16.9, ASTM A403 - WP316/316L, SEAMLESS, WALL THICKNESS TO MATCH PIPE

FLANGES ASME B16.5, 600#, WNRF, SMOOTH FINISH, ASTM A182 F316 / 316L

BLIND ASME B16.5, 600#, WNRF, SMOOTH FINISH, ASTM A182 F316 / 316L

FIG 8 / SPCR 600#, FF, SMOOTH FINISH, ASTM A240 TP 316/316L TO ASME B-16.48

WELDOLET MSS-SP-97, ASTM A182 GR F316/316L , BW ENDS, WALL THICKNESS TO MATCH PIPE

ASME B 18.2.1, ASTM –A193 Gr. B8 MACHINE BOLTS , FULL LENGTH UNC
JACKSCREW
THREAD WITH HEXAGONAL HEAD (Note-7)

GASKETS 4.5mm THK, 600# ASME B16.20, SS 316/316L GRAPHITE SPIRAL WOUND WITH SS INNER RING / CENTERING FLEXITALLIC “CG” OR EQUAL

BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

BALL-FULL
BA-92 BA-96 BA-98
VALVES (Note

BORE
2,4,9,10,11)

BALL-RED BORE BA-94 BA-97 BA-99

CHECK CH-43 CH-44 / CH-44A

GLOBE GL-31
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1.   Nipples to be manufactured in same material as pipe. ASME B 16.5 – Pipe Flanges and Flanged Fittings               Temp Press.
2.   For complete details of valves, please refer applicable individual valve datasheets. ASME B 16.48 – Steel Line Blanks (ºF) (psig)
32 to
3.   Line Joints :  For sizes  1/2” and Above   - BW ASME B 16.9 – Factory Made Wrought Butt Welding Fittings 1440
100
4.   Valve type selected shall be as per P&ID.                              ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 1240
5.   For Branching refer Appendix-C. ASME B31.3 – Process Piping  260 1168
6.  All Items shall be dual certified. ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels
7.  Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be provided with Jack Screw 
arrangement for the ease of removal 180° apart on one flange. Jack screw shall be procured separately while the drilling and the  ASME BPVC Section IX –Welding and Brazing Qualifications. 
tapping to match Jack Screw (as per Appendix-D) shall be done at Site.
8. Design limits According to ASME B16.5 Flange Rating material group 2.2 MSS SP-97– Integrally Reinforced Forged – Branched Outlet Fittings

9. The use of reduced bore valve is preferred. Use full bore valves only when necessary for processing / operating requirements.
10. Type of check valve to be Preferably  Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check valves are required 
Both Swing/Double flanged can be used.
11. Piston type check valves for horizontal mounting only.
12. Ball Valves shall be used for Isolation.
B * APR 2021 Final Issue SSP HAO HAO

A 03/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 Non-Impact tested C.S (with SW fittings for 1 ½” and below sizes) CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS PRESSURE TEST: DESIGN x 1.5 ASME CLASS 900 RF
PG, PH, PL E1B
General Engineering Services
Branch Connection Table BCT1(Note-6)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400
SCHEDULE SCH. 160 SCH. 120
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 8.74 11.13 11.13 14.27 18.26 21.44 25.4 27.79 30.96
PIPE PE, SMLS, ASTM-A106 GR.B, (Note 1,5) BE, SMLS, ASTM A-106 GR.B
FITTINGS SW, ASME B16.11, FORGED STEEL, 6000#, ASTM A105N BW, ASTM-A-234, GR. WPB, ASME B16.9 SEAMLESS, WALL THICKNESS TO MATCH PIPE
FLANGES 1500#, SW. RF, SMOOTH FINISH, ASTM A105N 900#, RF WN, SMOOTH FINISH, ASTM-A-105N, BORE TO MATCH PIPE

FIG 8 / SPCR & BLIND 900#, FF, 3.2 – 6.3 MICROMETER Ra, ASTM A516 – 60 / 70 TO ASME B-16.48

SOCKOLET FORGED STEEL, 6000# ASTM-A105N (Note-6)

WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-6)
CAPS SW, 6000# B16.11 ASTM A105N

UNIONS SW, FORGED STEEL 6000#, INTEGRAL SEATS, GROUND JOINT, ASTM-A105N

JACKSCREW ASME B 18.2.1, ASTM –A193-B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-3)

GASKETS 4.5mm THK, 900# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

BALL-FULL
BA-39 / BA-39H BA-41 / BA-41H BA-43 / BA-43H
VALVES (Note 2 ,4, & 8 )

BORE

BALL-RED BORE BA-40 / BA-40H BA-42 / BA-42H BA-44 / BA-44H

BUTTERFLY
CHECK CH-32 CH-16 / CH-16A (Note-7)
GATE GA-25 GA-27
GLOBE GL-25 GL-15
NEEDLE
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1. Nipples to be manufactured in same material as pipe ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings
Temp (ºF) Press. (psig)
2. For complete details of valves please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks

3. Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be provided with Jack Screw
arrangement for the ease of removal 180° apart on one flange. Jack screw shall be procured separately while the drilling and the tapping to ASME B 16.9 – Factory Made Wrought Butt Welding Fittings 32 to 100 2220
match Jack Screw (as per Appendix-D) shall be done at Site.
4. Valve type selected shall be as per P&ID. ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 2035
5. Line Joints : For sizes upto 1 ½” - SW ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded 350 1932.5
For sizes 2”& above - BUTT WELDED ASME B31.3 – Process Piping 400 1900
6. For Branching refer Appendix-C. ASME BPVC Section VIII, Div 1 & 2 – Rules for Construction of Pressure Vessels 500 1810
7. Type of check valve to be Preferably Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check valves are required Both
ASME BPVC Section IX –Welding and Brazing Qualifications. 600 1705
Swing/Double flanged can be used.
8. For temperature above 350 deg.F metal seated ball valve shall be used. 650 1650
9. Ball valves shall be used for Isolation.
B * APR 2021 Final Issue SSP HAO HAO

A 03/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 PIPING 
Non-Impact tested for t<1/2” & Impact tested for t> 1/2” - 900# C.S With SW Fittings for 1.5” and below sizes CORROSION ALLOWANCE 0.050in / 1.25 mm
SPECIFICATION
SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS FOR MIN SERVICE TEMP UPTO      -20°F PRESSURE TEST: DESIGN x 1.5 ASME CLASS 900 RF

General Engineering Services

PG, PL E6B
Branch Connection Table BCT1(Note-6)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300
SCHEDULE SCH. 160 SCH. 120
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 8.74 11.13 11.13 14.27 18.26 21.44 25.4 27.79 30.96
PIPE PE, SMLS, ASTM-A106 GR.B,   (Note 1,5) BE, SMLS, ASTM A-106 GR.B BE, SMLS, ASTM A-333 GR.6
FITTINGS SW, ASME B16.11, FORGED STEEL, 6000#, ASTM BW, ASTM-A-234, GR. WPB, ASME B16.9 SMLS, WT TO BW, ASTM-A-420, GR. WPL6, ASME B16.9 SMLS, WT TO MATCH PIPE
FLANGES 1500#, SW. RF, SMOOTH FINISH, ASTM A105N 900#RF, WN, SMOOTH FINISH, ASTM-A-105N, BORE TO MATCH PIPE
FIG 8 / SPCR & BLIND 900#, FF, SMOOTH FINISH, ASTM A516 – 60 / 70 TO ASME B-16.48
FORGED STEEL, 6000# ASTM-A105N
SOCKOLET
(Note-6)
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-6)
CAPS SW, 6000# B16.11 ASTM A105N
SW, FORGED STEEL 6000#, INTEGRAL SEATS,
UNIONS
GROUND JOINT, ASTM-A105N
JACKSCREW ASME B 18.2.1, ASTM –A193-B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-3)
GASKETS 4.5mm THK, 900# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUIVALENT
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

BALL-FULL
BA-39 BA-41 BA-67
BORE
VALVES (Note 2&4 )

BALL-RED
BA-40 BA-42 BA-68
BORE
BUTTERFL
Y
CHECK CH-32 CH-16 / CH-16A (Note-7) CH-33 / CH-33A (Note-7)
GATE GA-25 GA-27 GA-28
GLOBE GL-25 GL-15
NEEDLE
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1.  Nipples to be manufactured in same material as pipe ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings              
Temp (ºF) Press. (psig)
2.  For complete details of valves please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks
3. Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4”
and larger shall be provided with Jack Screw arrangement for the ease of removal 180° apart
ASME B 16.9 – Factory Made Wrought Butt Welding Fittings -20 to 100 2220
on one flange. Jack screw shall be procured separately while the drilling and the tapping to
match Jack Screw (as per Appendix-D) shall be done at Site.
4.  Valve type selected shall be as per P&ID. ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 2035
5.  Line Joints :  For sizes upto 1 ½”   - SW ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded  350 1932.5
                             For sizes 2”& above - BUTT WELDED ASME B31.3 – Process Piping 
6.  For Branching refer Appendix-C. ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels
7. Type of check valve to be Preferably Dual Plate Wafer Lug/Double Flanged except where
ASME BPVC Section IX –Welding and Brazing Qualifications. 
Dissimilar Check valves are required Both Swing/Double flanged can be used.
8. Ball Valves shall be used for Isolation.

B * APR 2021 Final Issue SSP HAO HAO

A 06/03/2016 Final Issue HAO SSP SSP
Rev. Date Description By Chk. App.
 Impact tested  for Low Temperature Service – 
CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION
900 #, LTCS with SW fittings for 1 ½” and below sizes

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS PRESSURE TEST: DESIGN x 1.5 ASME CLASS 900 RF

PG, PL, VL E7B
General Engineering Services
Branch Connection Table BCT1(Note-6)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 14 16
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300 350 400
SCHEDULE SCH. 160 SCH. 120
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 8.74 11.13 11.13 14.27 18.26 21.44 25.4 27.79 30.96

PIPE PE, SMLS, ASTM-A333 GR.6   (Note 1,5) BE, SMLS, ASTM A333 GR.6

SW, ASME B16.11, FORGED STEEL, 6000#, ASTM

FITTINGS BW, ASTM A420 GR. WPL 6, GR. WPB, ASME B16.9 SEAMLESS, WALL THICKNESS TO MATCH PIPE
A350 GR. LF2 CL.1
1500#, SW. RF, SMOOTH FINISH, ASTM A350 GR. LF2
FLANGES 900#, RF WN, SMOOTH FINISH, ASTM A350 GR. LF2 CL.1, BORE TO MATCH PIPE
CL.1
FIG 8 / SPCR & BLIND 900#, FF, 3.2 – 6.3 MICROMETER Ra, ASTM A516 – 60 TO ASME B-16.48
FORGED STEEL, 6000#
SOCKOLET
ASTM- A350 GR. LF2 CL.1 (Note-6)
MSS SP-97, ASTM- A350 GR. LF2 CL.1,
WELDOLET
SCHEDULE TO MATCH PIPE (Note-6)
CAPS SW, 6000# B16.11 ASTM A350 GR. LF2 CL.1
SW, FORGED STEEL 6000#, INTEGRAL SEATS, GROUND
UNIONS JOINT,
ASTM- A350 GR. LF2 CL.1
JACKSCREW ASME B 18.2.1, ASTM –A193-B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-3)
GASKETS 4.5mm THK, 900# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
BOLTING ASTM-A320 GR. L7 STUD BOLTS W/ASTM-A194 GR. 4 NUTS
BALL-FULL
BA-80 BA-82 BA-67
BORE
VALVES (Note 2&4 )

BALL-RED
BA-81 BA-83 BA-68
BORE
BUTTERFLY
CHECK CH-37 CH-38 / CH-38A (Note-7)
GATE GA-29 GA-30
GLOBE GL-27 GL-28
NEEDLE
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1.  Nipples to be manufactured in same material as pipe ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings              
Temp (ºF) Press. (psig)
2.  For complete details of valves please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks
3. Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger
shall be provided with Jack Screw arrangement for the ease of removal 180° apart on one flange.
ASME B 16.9 – Factory Made Wrought Butt Welding Fittings -50 to 100 2220
Jack screw shall be procured separately while the drilling and the tapping to match Jack Screw (as
per Appendix-D) shall be done at  Site.
4.  Valve type selected shall be as per P&ID. ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 2035
5.  Line Joints :  For sizes upto 1 ½”   - SW ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded 
                             For sizes 2”& above - BUTT WELDED ASME B31.3 – Process Piping 
6.  For Branching refer Appendix-C. ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels
7. Type of check valve to be Preferably Dual Plate Wafer Lug/Double Flanged except where
ASME BPVC Section IX –Welding and Brazing Qualifications. 
Dissimilar Check valves are required Both Swing/Double flanged can be used.
8. Ball valves shall be used for Isolation

B * APR 2021 Final Issue SSP HAO HAO

A 06/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 Non-Impact tested – 900# C.S With internal coating / PE lining CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : PRODUCED WATER PRESSURE TEST: DESIGN x 1.5 ASME CLASS 900 RF

WO PIPING WITH INTERNAL COATING / LINING E1W (Note-9)
General Engineering Services
Branch Connection Table BCT1 (Note-7)
NOMINAL DIA (inch) 2 3 4 6 8 10 12
NOMINAL DIA (mm) 50 80 100 150 200 250 300
SCHEDULE SCH. 160 SCH. 120
WALL THICKNESS (mm) 8.74 11.13 11.13 14.27 18.26 21.44 25.4
PIPE (Note – 10, 13) BE, SMLS, ASTM A-106 GR.B

FITTINGS (Note – 10, 13) BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS,WALL THICKNESS TO MATCH PIPE

FLANGES 900#,RF WN, SMOOTH FINISH, ASTM A-105N, BORE TO MATCH PIPE
SOCKOLET
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-7)
ASME B 18.2.1, ASTM –A193 Gr. B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH
JACKSCREW
HEXAGONAL HEAD (Note-6)
UNIONS
4.5mm THK, 900# ASME B16.20 316SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL (Gasket 
GASKETS
is not required if the pipe is PE lined)
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS
VALVES (Note 2, 4

BALL-FULL
BA-104 W BA-106 W
BORE
BALL-RED
& 9)

BA-105 W BA-107 W
BORE
CHECK CH – 47 / CH- 47A
GLOBE GL-15-W
GENERAL NOTES: Notes (Contd.) DESIGN LIMITS
1.   Nipples to be manufactured in same material as pipe. 13. PE lining of straight pipe spools shall be carried out by Piping Fabrication Contractor. 
Press.
The maximum length of spool has to be verified from Piping Fabrication Contractor (which has to be less than 18m due to  Temp (ºF)
2.   For complete details of valves, please refer applicable individual valve datasheets. (psig)
transportation limitations).
3.   Line Joints :  For sizes  2” & above          - BUTT WELDED 14. Bolt lengths shall be finalized after thickness of PE liner is calculated by Vendor. 32 to 100 2160
4.   Valve type selected shall be as per P&ID. 140 2040
5.   Minimum size of branches shall be 2” (including vent and drains). MANDATORY CODES & STANDARDS:
6.    Flanges used for Restriction Orifices of size 4” and larger shall be provided with Jack Screw arrangement for the ease of 
removal 180° apart on one flange. Jack screw shall be procured separately while the drilling and the tapping to match Jack  API 6D – Flanged Valves
Screw (as per Appendix-D, ) shall be done at Site.
7. For Branching refer Appendix-C. ASME B 16.5 –  Pipe Flanges and Flanged Fittings             

8.Do not use spectacle blinds or spades in lined piping. Use drop out spools (preferably near elbow) where required.  ASME B 16.9 – Factory Made Wrought Butt Welding Fittings
9. “W” indicates – (a). All pipes & Fittings with Internal rotolining / internal epoxy coated or PE lined. Type of internal coating 
ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded
shall be discussed with Oxy corrosion engineer
10. All pipes & fittings shall be procured with butt welding ends. Welding of flanges and rotolining of the fabricated assembly / 
ASME B31.3 – Process Piping 
spools shall be carried out by Piping Fabricator Contractor
11. For PE lined piping, annulus vent connection (1/8” dia. hole drilled on the main pipe) with valves, flanges, gaskets and 
ASME Section VIII – Boiler & Pressure Vessels Code, Pressure Vessels, Div 1& 2
fasteners of ¾” size (as per pipe class F6C) shall be provided near flange joints.

Also, backing rings shall be provided at all flanged joints. ASME Section IX –Welding Qualifications

12. PE liner thickness calculation shall be submitted by PE liner vendor for Oxy’s approval.
 
B * APR 2021 Final Issue SSP HAO HAO

A 06/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 CORROSION  PIPING 
Class 900 S.S 316 / SS 316L; Dual Certified (NOTE – 6) 0 mm
ALLOWANCE SPECIFICATION
ASME CLASS 900 
SERVICE : HYDROCARBONS  PRESSURE TEST: DESIGN X 1.5
RF
PL, PG & VL E2C
General Engineering Services
Branch Connection Table BCT1 (Note-5)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4
NOMINAL DIA (mm) 15 20 25 40 50 80 100
SCHEDULE SCH. 80S
WALL THICKNESS (mm) 3.73 3.91 4.55 5.08 5.54 7.62 8.56
PIPE BEVEL ENDS, SMLS, ASTM-A312 TP 316 / 316L,  (Note 1, 3)
FITTINGS BW, ASME B16.9, ASTM A403 – WP 316 / 316L, SEAMLESS, WALL THICKNESS TO MATCH PIPE
FLANGES & BLIND ASME B16.5, 900#, WNRF, SMOOTH FINISH, ASTM A182 F316 / 316L
FIG 8 / SPCR 900#, FF, SMOOTH FINISH, ASTM A240 TP 316 / 316L TO ASME B-16.48
MSS-SP-97, ASTM A182 GR F316 / 316L , BW
WELDOLET
WALL THICKNESS TO MATCH PIPE
GASKETS 4.5mm THK, 900# ASME B16.20, SS 316 (L) GRAPHITE SPIRAL WOUND WITH SS INNER RING /
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS
BALL-FULL
VALVES (Note 2,

BA-100/BA-100H BA-102/BA-102H
BORE
4, 8, 9, 10)

BALL-RED
BA-101/BA-101H BA-103/BA-103H
BORE
CHECK CH-45 CH-46 / CH-46A
GLOBE GL-32
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1.   Nipples to be manufactured in same material as pipe. ASME B 16.5 – Pipe Flanges and Flanged Fittings               Press.
Temp (ºF)
2.   For complete details of valves, please refer applicable individual valve datasheets. ASME B 16.48 – Steel Line Blanks (psig)
3.   Line Joints :  For sizes  1/2” and Above   - BW ASME B 16.9 – Factory Made Wrought Butt Welding Fittings 32 to 100 2160
4.   Valve type selected shall be as per P&ID.                              ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 1860
5.   For Branching refer Appendix-C. ASME B31.3 – Process Piping  300 1680
6. All items shall be dual certified. ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of  350 1610
7. Design limits According to ASME B16.5 Flange Rating material group 2.2 ASME BPVC Section IX –Welding and Brazing Qualifications. 
8. The use of reduced bore valve is preferred. Use full bore valves only when necessary for processing /  MSS SP-97– Integrally Reinforced Forged – Branched Outlet Fittings
9. Piston type check valves for horizontal mounting only.
10. Type of check valve to be Preferably  Dual Plate Wafer Lug/Double Flanged except where Dissimilar 
Check valves are required Both Swing/Double flanged can be used.
11. Ball Valves shall be used for Isolation.

B * APR 2021 Final Issue SSP HAO HAO

A 06/03/2016 Final Issue HAO SSP SSP
Rev. Date Description By Chk App.
 PIPING 
Non-Impact tested 1500# Carbon Steel with BW fittings  CORROSION ALLOWANCE 0.050in / 1.25 mm
SPECIFICATION

ASME CLASS 1500    
SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS PRESSURE TEST: DESIGN x 1.5
RTJ
PG, PL F1C
General Engineering Services
Branch Connection Table BCT1(Note-6)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300
SCHEDULE SCH. 160
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 8.74 11.13 13.49 18.26 23.01 28.58 33.32

PIPE BE, SMLS, ASTM-A106 GR.B, (Note 1,5) BE, SMLS, ASTM A-106 GR.B

BUTT WELD ENDS , ASME B16.9, FORGED STEEL, ASTM

FITTINGS BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS, WALL THICKNESS TO MATCH PIPE
A105N
FLANGES WN, 1500# RTJ, ASTM A105N 1500#, RTJ WN, ASTM-A-105N, BORE TO MATCH PIPE
FIG 8 / SPCR & BLIND 1500#, RTJ, ASTM A 516 Gr.60, TO ASME B-16.48
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-6)
PLUGS

JACKSCREW ASME B 18.2.1, ASTM –A193- B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-3)

GASKETS TYPE R, 1500#, ASME B16.20, OCTAGONAL RING, SOFT IRON (90 BHN MAX), CADMIUM PLATED
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS
BALL-FULL
BA-45 BA-47 BA-49
VALVES (Note 2&4 )

BORE
BALL-RED
BA-46 BA-48 BA-50
BORE
BUTTERFLY
CHECK CH-17 CH-18 / CH-18A (Note-7)
GATE GA-13 GA-14
GLOBE
NEEDLE
MANDATORY CODES & STANDARDS:
GENERAL NOTES: DESIGN LIMITS
ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings              

1.  Nipples to be manufactured in same material as pipe ASME B 16.48– Steel Line Blanks Temp (ºF) Press. (psig)

2.  For complete details of valves please refer applicable individual valve datasheets. ASME B 16.9 – Factory Made Wrought Butt Welding Fittings 46 to 100 3705

3. Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be
provided with Jack Screw arrangement for the ease of removal 180° apart on one flange. Jack screw shall be ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 3395
procured separately while the drilling and the tapping to match Jack Screw (as per Appendix-D) shall be done at
Site. ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded 
4.  Valve type selected shall be as per P&ID. ASME B31.3 – Process Piping 
5.  Line Joints :  For all sizes   -BUTT WELDED ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels
6.  For Branching refer Appendix-C. ASME BPVC Section IX –Welding and Brazing Qualifications. 
7. Type of check valve to be Preferably Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check
valves are required Both Swing/Double flanged can be used.
8. Ball Valves shall be used for Isolation.
B * APR 2021 Final Issue SSP HAO HAO
A 06/03/2016 Final Issue HAO SSP SSP
Rev. Date Description By Chk. App.
 Non-Impact tested CS for t < ½” and  Impact tested CS for t> ½” -  1500# with BW fittings  CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS FOR MIN SERVICE TEMP UPTO  -20°F PRESSURE TEST: DESIGN x 1.5 ASME CLASS 1500    RTJ

PG, PL F6C
General Engineering Services
Branch Connection Table BCT1(Note-6)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300
SCHEDULE SCH. 160
WALL THICKNESS (mm) 4.78 5.56 6.35 7.14 8.74 11.13 13.49 18.26 23.01 28.58 33.32
PIPE BE, SMLS, ASTM-A106 GR.B, (Note 1,5) BE, SMLS, ASTM A106-B BE, SMLS, ASTM A-333 GR.6
BW, ASTM-A-234-WPB, ASME
BW, ASME B16.9, ASTM A234-WPB ; SMLS, WT TO
FITTINGS B16.9, SMLS, WT TO MATCH BW, ASTM-A-420-WPL6, ASME B16.9, SMLS, WT TO MATCH PIPE
MATCH PIPE
PIPE
FLANGES WN, 1500# RTJ, ASTM A105N 1500#, RTJ WN,1500#, ASTM-A-105N, BORE TO MATCH PIPE
FIG 8 / SPCR & BLIND 1500#, RTJ, ASTM A 516 Gr.60 / 70, TO ASME B-16.48
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-6)
PLUGS
JACKSCREW ASME B 18.2.1, ASTM –A193- B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-3)
GASKETS TYPE R, 1500#, ASME B16.20, OCTAGONAL RING, SOFT IRON (90 BHN MAX), CADMIUM PLATED
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

BALL-FULL
BA-45 BA-47 BA-72
BORE
VALVES (Note 2&4 )

BALL-RED
BA-46 BA-48 BA-73
BORE

BUTTERFLY

CHECK CH-17 CH-18 / CH-18A (Note-7) CH-35 / CH-35A (Note-7)

GATE GA-13 GA-14 GA-26
GLOBE
NEEDLE
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1.  Nipples to be manufactured in same material as pipe ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings               Temp (ºF) Press. (psig)
2.  For complete details of valves please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks -20 to 100 3705
3. Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and
larger shall be provided with Jack Screw arrangement for the ease of removal 180° apart on one
ASME B 16.9 – Factory Made Wrought Butt Welding Fittings 200 3395
flange. Jack screw shall be procured separately while the drilling and the tapping to match Jack
Screw (as per Appendix-D) shall be done at  Site.
4.  Valve type selected shall be as per P&ID. ASME B-16.34 –Valves, Flanged, Threaded and Welding End
5.  Line Joints :  For all sizes   -BUTT WELDED ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded 
6.  For Branching refer Appendix-C. ASME B31.3 – Process Piping 
7. Type of check valve to be Preferably Dual Plate Wafer Lug/Double Flanged except where
ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels
Dissimilar Check valves are required Both Swing/Double flanged can be used.
8. Ball Valves shall be use for Isolation. ASME BPVC Section IX –Welding and Brazing Qualifications. 

B * APR 2021 Final Issue SSP HAO HAO

A 06/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.

 Non-Impact tested – 1500# C.S With internal coating / PE lining CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : PRODUCED WATER PRESSURE TEST: DESIGN x 1.5 ASME CLASS 1500 RF

WI, WO PIPING WITH INTERNAL COATING / LINING F1W (Note-9)

General Engineering Services
Branch Connection Table BCT1 (Note-7)

NOMINAL DIA (inch) 2 3 4 6 8 10 12

NOMINAL DIA (mm) 50 80 100 150 200 250 300

SCHEDULE SCH. 160

WALL THICKNESS (mm) 8.74 11.13 13.49 18.26 23.01 28.58 33.32

PIPE (Note – 10, 13) BE, SMLS, ASTM A-106 GR.B

BW, ASTM-A-234, GR. WPB, ASME B16.9, SEAMLESS,
FITTINGS (Note – 10, 13)
WALL THICKNESS TO MATCH PIPE
FLANGES 1500#,RF WN, SMOOTH FINISH, ASTM A-105N, BORE TO MATCH PIPE
FIG * / SPAR & BLIND 1500#,RF, ASTM A516 Gr. 60, TO ASME B 16.48
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-7)
ASME B 18.2.1, ASTM –A193 Gr. B8 MACHINE BOLTS, FULL LENGTH UNC THREAD
JACKSCREW
WITH HEXAGONAL HEAD (Note-6)

4.5mm THK, 1500# ASME B16.20 316 SS GRAPHITE SPIRAL WOUND WITH INNER RING FLEXITALLIC “CG” OR EQUAL
GASKETS
(Gasket is not required if the pipe is PE lined)

BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

VALVES (Note 2,

BALL-FULL BORE BA-108 W BA-110 W

4 & 9)

BALL-RED BORE BA-109 W BA-111 W

CHECK CH – 49 W / CH- 50 W
GLOBE GL-10 W
GENERAL NOTES: Notes (Contd.) DESIGN LIMITS
1. Nipples to be manufactured in same material as pipe. 13. PE lining of straight pipe spools shall be carried out by Piping Fabrication Contractor.
Temp (ºF) Press. (psig)
2. For complete details of valves, please refer applicable individual valve datasheets. The maximum length of spool has to be verified from Piping Fabrication Contractor (which has to be less than 18m due to transportation limitations).

3. Line Joints : For sizes 2” & above - BUTT WELDED 14. Bolt lengths shall be finalized after thickness of PE liner is calculated by Vendor. 32 to 100 3600

4. Valve type selected shall be as per P&ID. 140 3398

6. Flanges used for Restriction Orifices of size 4” and larger shall be provided with Jack Screw arrangement for the ease of
MANDATORY CODES & STANDARDS:
removal 180° apart on one flange. Jack screw shall be procured
separately while the drilling and the tapping to match Jack Screw (as per Appendix-D, of OMN-FAC-406) shall be done at
API 6D – Flanged Valves
Site.
7. For Branching refer Appendix-C of OMN-FAC-406. ASME B 16.5 – Pipe Flanges and Flanged Fittings

8. Do not use spectacle blinds or spades in lined piping. Use drop out spools (preferably near elbow) where required. ASME B 16.9 – Factory Made Wrought Butt Welding Fittings

9. “W” indicates – (a). All pipes & Fittings with Internal rotolining / internal epoxy coated or PE lined. Type of internal
ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded
coating shall be discussed with Oxy corrosion engineer
10. All pipes & fittings shall be procured with butt welding ends. Welding of flanges and rotolining of the fabricated
ASME B31.3 – Process Piping
assembly / spools shall be carried out by Piping Fabricator Contractor
11. For PE lined piping, annulus vent connection (1/8” dia. hole drilled on the main pipe) with valves, flanges, gaskets and
ASME Section VIII – Boiler & Pressure Vessels Code, Pressure Vessels, Div 1& 2
fasteners of ¾” size (as per pipe class F6C) shall be provided near flange joints.
Also, backing rings shall be provided at all flanged joints. ASME Section IX –Welding Qualifications

12. PE liner thickness calculation shall be submitted by PE liner vendor for Oxy’s approval. B * APR 2021 Final Issue SSP HAO HAO

A 02/03/2016 Final Issue HAO SSP SSP

Rev DATE DESCRIPTION ISSUED BY APPROVED BY APPROVED BY

 Non Impact tested Carbon Steel with butt welded fittings ,2500#  CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS PRESSURE TEST: DESIGN x 1.5 ASME CLASS 2500    RTJ

PG G1C
General Engineering Services
Branch Connection Table BCT1(Note-7) 
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300
SCHEDULE SCH. XXS CALCULATED (Note-6)
WALL THICKNESS (mm) 7.47 7.82 9.09 10.15 11.07 15.5 19.5 28 36 44.5 52.5
PIPE BE, SMLS, ASTM-A106 GR.B, (Note-1) BE, SMLS, ASTM-A106 GR.B
FITTINGS BW, ASME B16.9, FORGED STEEL, ASTM A105N BW, ASTM-A-234, GR. WPB, ASME B16.9 SEAMLESS , WALL THICKNESS TO MATCH PIPE
FLANGES 2500#, RTJ WN, ASTM-A-105N, BORE TO MATCH PIPE
SOCKOLET
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-7)
STEEL LINE BLANK 2500#, RTJ, ASTM A 516 Gr.60 / 70 TO ASME B-16.48
ASME B 18.2.1, ASTM –A193 B8 MACHINE BOLTS, FULL LENGTH UNC THREAD
JACKSCREW
WITH HEXAGONAL HEAD (Note-3)
GASKETS TYPE R, 2500#, ASME B16.20, OCTAGONAL RING, SOFT IRON (90 BHN MAX), CADMIUM PLATED
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS
BALL-FULL
(Note-8) BA-55 BA-63
VALVES (Note 2&4 )

PORT
BALL-RED
(Note-8) BA-56 BA-64
PORT
BUTTERFLY
CHECK CH-19 CH-23 / CH-23A ( Note-9)
GATE GA-17 GA-18
GLOBE GL-13 GL-14
GENERAL NOTES:
MANDATORY CODES & STANDARDS: DESIGN LIMITS
1.  Nipples to be manufactured in same material as pipe.
2. For valve description refer valve data sheets. ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings              
3. Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and ASME B 16.48– Steel Line Blanks
Temp (ºF) Press. (psig)
larger shall be provided with Jack Screw arrangement for the ease of removal 180° apart on one
flange. Jack screw shall be procured separately while the drilling and the tapping to match Jack ASME B 16.9 – Factory Made Wrought Butt Welding Fittings
Screw (as per  Appendix-D) shall be done  at  Site.
4. In case any welded fitting is approved, it has to be 100% radiographed. ASME B-16.34 –Valves, Flanged, Threaded and Welding End 46 to 100 6170
5. Valve type selected shall be as per P&ID. ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded  200 5655
6. Due to non-availability of required sizes in ASME  B36.10 minimum required thicknesses are 
ASME B31.3 – Process Piping 
specified.
7. For Branching table refer Appendix-C. ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels

8. In place of Ball valves, Gate valves shall be used. ASME BPVC Section IX –Welding and Brazing Qualifications
9.Type of check valve to be Preferably  Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check 
valves are required Both Swing/Double flanged can be used.
10. Ball valves shall be used for isolation.

  B * APR 2021 Final Issue SSP HAO HAO

A 06/03/2016 Final Issue HAO SSP SSP

Rev Date Description By CHKD APPR

 Non-Impact tested CS for t < ½” and  Impact tested CS for t> ½” -  2500# with BW fittings CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS FOR MIN SERVICE TEMP UPTO -20°F PRESSURE TEST: DESIGN x 1.5 ASME CLASS 2500    RTJ

PG G6C
General Engineering Services
Branch Connection Table BCT1(Note-7) 
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300
SCHEDULE SCH. XXS CALCULATED (Note-6)
WALL THICKNESS (mm) 7.47 7.82 9.09 10.15 11.07 15.5 19.5 28 36 44.5 52.5
PIPE BE, SMLS, ASTM-A106 GR.B, (Note-1) BE, SMLS, ASTM-A333 GR.6
FITTINGS BW, ASME B16.9, ASTM A234-WPB ; SMLS, WT TO MATCH PIPE BW, ASTM-A-420, GR. WPL6, ASME B16.9 SEAMLESS , WALL THICKNESS TO MATCH PIPE
FLANGES 2500#RTJ WN, ASTM-A-105N, BORE TO MATCH PIPE
WELDOLET MSS SP-97, ASTM-A105N, SCHEDULE TO MATCH PIPE (Note-7)
STEEL LINE BLANK 2500#, RTJ, ASTM A 516 Gr.60 / 70, TO ASME B-16.48
JACKSCREW ASME B 18.2.1, ASTM –A193 B8 MACHINE BOLTS, FULL LENGTH UNC THREAD WITH HEXAGONAL HEAD (Note-3)
GASKETS TYPE R, 2500#, ASME B16.20, OCTAGONAL RING, SOFT IRON (90 BHN MAX), CADMIUM PLATED
BOLTING ASTM-A-193 GR. B7 STUD BOLTS W/ASTM-A194 GR. 2H NUTS

BALL-FULL PORT (Note-8) BA-55 BA-63

VALVES (Note 2&4 )

BALL-RED PORT (Note-8) BA-56 BA-64

BUTTERFLY
CHECK CH-22 CH-23/CH23A (Note-9)
GATE GA-17 GA-18
GLOBE GL-13 GL-14
GENERAL NOTES: MANDATORY CODES & STANDARDS:
1.     Nipples to be manufactured in same material as pipe. ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings               DESIGN LIMITS
2.  For valve description refer valve data sheets. ASME B 16.48– Steel Line Blanks
3.  Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and Press.
ASME B 16.9 – Factory Made Wrought Butt Welding Fittings Temp (ºF)
larger shall be provided with  Jack Screw arrangement  for the  ease of  removal  180° (psig)
apart on one flange. Jack screw shall be procured separately while the drilling and the tapping
ASME B-16.34 –Valves, Flanged, Threaded and Welding End -20 to 100 6170
to match Jack Screw (as per  Appendix-D) shall be done  at  Site.
4. In case any welded fitting is approved, it has to be 100% radiographed. ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded  200 5655
5. Valve type selected shall be as per P&ID. ASME B31.3 – Process Piping 
6.  Due to non-availability of required sizes in ASME B36.10 minimum required thicknesses are
ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels
specified.
7.  For Branching table refer Appendix-C. ASME BPVC Section IX –Welding and Brazing Qualifications
8. In place of Ball valves, Gate valves shall be used.
9.Type of check valve to be Preferably Dual Plate Wafer Lug/Double Flanged except where
Dissimilar Check valves are required Both Swing/Double flanged can be used.
10. Ball valves shall be used for Isolation.

B * APR 2021 Final Issue SSP HAO HAO

A 06/03/2016 Final Issue HAO SSP SSP

Rev Date Description By CHKD APPR

 Impact tested for low temp. service – 2500# C.S with BW fittings CORROSION ALLOWANCE 0.050in / 1.25 mm PIPING SPECIFICATION

SERVICE : GENERAL PIPING FOR SWEET HYDROCARBONS PRESSURE TEST: DESIGN x 1.5 ASME CLASS 2500 RTJ

PG G7C
General Engineering Services
Branch Connection Table BCT1 (Note-7)
NOMINAL DIA (inch) 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
NOMINAL DIA (mm) 15 20 25 40 50 80 100 150 200 250 300
SCHEDULE SCH. XXS (Note-8)
WALL THICKNESS (mm) 7.47 7.82 9.09 10.15 11.07 15.5 19.5 28 36 44.5 52.5
PIPE BE, SMLS, ASTM-A333 GR.6, (Note 1,3) BE, SMLS, ASTM-A333 GR.6
FITTINGS BW, ASTM-A420, GR. WPL 6, ASME B16.9, SEAMLESS , WALL THICKNESS TO MATCH PIPE
FLANGES RTJ WN, 2500#, ASTM-A350 LF2 CL1, BORE TO MATCH PIPE
SOCKOLET
WELDOLET MSS SP-97, ASTM-A350 LF2CL1, SCHEDULE TO MATCH PIPE (Note-7)
STEEL LINE BLANK ASME B16.48,SPECTACLE BLIND,ASTM A 516 Gr.70, SUITABLE FOR ASME B16.5 ,2500# RTJ

ASME B 18.2.1, ASTM –A193 B8 MACHINE BOLTS, FULL LENGTH UNC

JACKSCREW
THREAD WITH HEXAGONAL HEAD (Note-6)

GASKETS TYPE R, 2500# ASME B16.20, OCTAGONAL RING, SOFT IRON (90 BHN MAX), CADMIUM PLATED
BOLTING ASTM-A-320 GR. L7 STUD BOLTS W/ASTM-A194 GR. 4 NUTS

BALL-FULL BORE (Note-9) BA-55 BA-63

VALVES (Note 2 & 4)

BALL-RED BORE (Note-9) BA-56 BA-64

BUTTERFLY
CHECK CH-22 CH-23 / CH-23A (Note-10)
GATE GA-17 GA-18
GLOBE GL-13 GL-14
NEEDLE
GENERAL NOTES: MANDATORY CODES & STANDARDS: DESIGN LIMITS
1.   Nipples to be manufactured in same material as pipe. ASME B 16.5 & ASME B 16.47 Series A – Pipe Flanges and Flanged Fittings               Press.
Temp (ºF)
2.    For complete details of valves  please refer applicable individual valve datasheets. ASME B 16.48– Steel Line Blanks (psig)
3.   Line Joints :  For sizes upto ½ ” & ABOVE             -  BUTT WELDED ASME B 16.9 –  Factory Made Wrought Butt Welding Fittings -50 to 100 6170
 4.  Valve type selected shall be as per P&ID. ASME B-16.34 –Valves, Flanged, Threaded and Welding End 200 5655
5.   For Welded fittings all welds shall be 100% radiographed. ASME B 16.11 – Forged Steel Fittings, Socket Welding and Threaded 
6.    Flanges used for Steel line blanks, Paddles, Spacers and Restriction Orifices of size 4” and larger shall be provided with Jack Screw arrangement for the 
ease of removal 180° apart on one flange. Jack screw shall be procured separately while the drilling and the tapping to match Jack Screw (as per Appendix-D)  ASME B31.3 – Process Piping 
shall be done at  Site.
7.    For Branching refer Appendix-C. ASME BPVC Section VIII,  Div 1 & 2 – Rules for Construction of Pressure Vessels
8.   Due to non-availability of required sizes in ASME  B36.10  minimum required thicknesses are specified. ASME BPVC Section IX –Welding and Brazing Qualifications. 
9.    In place of Ball valves, Gate valves shall be used.
10.  Type of check valve to be Preferably  Dual Plate Wafer Lug/Double Flanged except where Dissimilar Check valves are required Both Swing/Double flanged 
can be used.
11. Ball Valves shall be used for Isolation
B * APR 2021 Final Issue SSP HAO HAO

A 06/03/2016 Final Issue HAO SSP SSP

Rev. Date Description By Chk. App.