NAPHTHAPLAST G-808UL

Water-Reducing & Retarding Super-Plasticizer

Description

High range water reducer designed to obtain rheoplastic concrete with slump of at least 100mm, without
segregation.

• Reduces thermal peaks.

• Extended setting time and longer workability.
• Reduction of 15% water content.
• Increases ultimate compressive strength.
• Effects economies of concrete mix by saving cement.
• Improves pump-ability of the material.
• Improves cohesive properties of concrete.
• Reduces the placing problems in hot weather concrete.
• Improves trowel-ability & surface finish.
• Reduces the incidence of honeycombing, shrinkage and cold joints during vibration.

Recommended Uses

• Pre-cast concrete manufacture.

• Ready mix concrete.
• Long distance transportation.
• In hot weather conditions, to extend workability.
• Mass concrete pours.

ADMIXTURES

S PAEDCMI A
I XLTAUDRME ISX T U R E S

S USRPFEACCI A
E LI MAPDRMOI V
XE M RE EN ST
TU

G RSOU UR TF SA C E I M P R O V E M E N T

W AGTREORUPT RS O O F I N G

F LW
OAOTREI R
NPGR O O F I N G

I NF
DLUO
SOTR
RIIANLGC O A T I N G S

J OI INNDTUSSETARLI A N
L TCSO A T I N G S

R EJPOAI INRT / SCERAALCAKN ITNSJ E C T I O N

TIR
L IENPGA S
I RY/SCTREAMCSK I N J E C T I O N

TILING SYSTEMS
Technical Data

Type G-808UL

Color Dark brown liquid

Chloride content to
BS5075 :1982 Nil

Nitrate content Nil Important Information:

Consumption with 100kg Cement 0.5 - 1.5 % Supplied in: 210 Liter Drums or
1000 litre IBC tanks.
Specific Gravity 1.18 - 1.20 @ 25 °C

Air contents
Storage: In a dry, frost free area, out of
Less than 1%
direct sunlight. If product has frozen,
Freezing Point 0°C. can be reconstituted, thaw and agitate until completely
if stirred after thawing reconstituted.

Flash Point None Shelf life: 24 months.

Hazard Class: No dangerous goods. Consult

MSDS for details.

Standards:
Application Guidelines ASTM C-494 Type B, D and G.

Setting Time:
NaphthaPlast G-808UL ensures that rehoplastic concrete remains workable in excess of 3
hours at +20°C. Workability loss is dependent on temperature, type of cement, nature of
aggregate and, method of transport. It is strongly recommended that concrete should be
properly cured, particularly in hot and dry climates.

Effect of Over Dosage:

• Retardation of initial set.
• Increase in air contents.
• Loss of workability.
• Bleed/segregation of mix.

Mixing:
NaphthaPlast G-808UL should be added to concrete during mixing cycle at same time as the
water and aggregates. Never add G-808UL to the dry cement. G-808UL is introduced into the
mixer together with mixing water. The plasticizing effect or water reduction is higher if the
admixture is added to the concrete after 50-70% of the mixing water has been added.

Curing:
Fresh poured concrete must be cured properly, particularly when subject to high
temperatures, in order to prevent drying shrinkages and cracks. Use Vertex Curing
Compounds to achieve best results or apply wet hessians.

Caution:
NaphthaPlast G-808UL is not a fire or health hazard. Spillages should be washed down
immediately with cold water. For further information refer to the material safety data sheet.
The information provided in this leaflet is supplied by our consulting service and is the end result of exhaustive research and extensive
experience. However, it is without any liability on our part particularly regarding third party proprietary rights. This information does not
relieve the user of the responsibility for verifying that the products and processes are suitable for the intended application. The data
presented was derived from tests under normal climate conditions according to DIN 50014 and mean average values and analysis.
Deviations are possible when delivery takes place. Given the recommendations may differ from those shown in this leaflet, written
confirmation should be sought. It is the responsibility of the purchaser to ensure they have latest leaflet issue and that its contents are
current. Our customer service staff will be glad to provide assistance at any time. We appreciate the interest you have shown in our
products. This technical datasheet supersedes previously issued information.

VERTEX
C hem i ca ls (Pvt .) Lt d.
Plot # 1-A Misc Zone, Phone: +92 (0) 41 8507212-13
Value Addition City, Fax: +92 (0) 41 850 7214
Sahianwala Road Khurriawala, Email: [email protected]
Faisalabad, Pakistan. Website: vertexchemicals.pk