SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 1/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE
COMPANY/UNDERTAKING
Product identifier
Product name: CADWELD® Mold Sealer (T403)
Relevant identified uses of the substance or mixture and uses advised against
Application: Sealer.
Details of the supplier of the safety data sheet
Manufacturer: nVent
ERICO International Corporation
34600 Solon Road
Solon, Ohio 44139
Tel:(440) 248-0100
Further information can be
[email protected]obtained from:
Emergency telephone number
Emergency telephone: National Capital Poison Center: 1-800-222-1222
Chemtel
1-800-255-3924 USA
+01-813-248-0585 International
SECTION 2: HAZARDS IDENTIFICATION
Classification of the substance or mixture
OSHA 2012: Not classified.
Data shows that products containing less than 8.5% disodium tetraborate
decahydrate (CAS 1303-96-4) are not hazardous to reproduction
Label elements
The substance/mixture does not meet the criteria for classification and labeling.
Other hazards
PBT/vPvB: This product does not contain any PBT or vPvB substances.
Other: Dust may irritate throat and respiratory system and cause coughing. The product
may contain crystalline silica in respirable fraction.
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
Mixtures
Only classified substances above threshold limits are shown.
SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 2/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
OSHA 2012:
%: CAS-No.: EC No.: REACH Reg. Chemical name: Hazard Notes:
No: classification:
10-20 1332-58-7 310-194-1 - Kaolin - #
1-<8.5 1303-96-4 - Disodium tetraborate Decahydrate Category 1B SCL
reproductive
toxicantFD
Notes: #: The substance has been assigned an exposure limit.
References: The full text for all hazard statements is displayed in section 16.
SECTION 4: FIRST AID MEASURES
Description of first aid measures
Inhalation: Dust inhalation: Move into fresh air and keep at rest. Get medical attention if any
discomfort continues.
Skin contact: Remove contaminated clothing immediately and wash skin with soap and water.
Then apply a fatty cream.
Eye contact: Immediately flush with plenty of water for at least 15 minutes. Remove any
contact lenses and open eyelids widely. If irritation persists: Seek medical
attention and bring along these instructions.
Ingestion: Immediately rinse mouth and drink 1-2 glasses of water. Keep person under
observation. If uncomfortable: Transportation to hospital. Bring along these
instructions.
Most important symptoms and effects, both acute and delayed
Symptoms/effects: See section 11 for more detailed information on health effects and symptoms.
Indication of any immediate medical attention and special treatment needed
Medical attention/treatments: Treat symptomatically.
SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 3/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
SECTION 5: FIREFIGHTING MEASURES
Extinguishing media
Extinguishing media: Use fire-extinguishing media appropriate for surrounding materials.
Special hazards arising from the substance or mixture
Specific hazards: No specific precautions.
Ignition temperature: >1650 °F (900 °C)
Advice for firefighters
Protective equipment for fire- Selection of respiratory protection for fire fighting: follow the general fire
fighters: precautions indicated in the workplace.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Personal precautions: Avoid generation and spreading of dust. Avoid inhalation of dust.
Environmental precautions
Environmental No special precautions.
precautions:
Methods and material for containment and cleaning up
Spill Cleanup Methods: Collect spillage with shovel, broom or the like.
Reference to other sections
References: For personal protection, see section 8.
For waste disposal, see section 13.
SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 4/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
SECTION 7: HANDLING AND STORAGE
Precautions for safe handling
Safe handling advice: Avoid inhalation of dust and contact with skin and eyes. Change contaminated
clothing.
Technical measures: All product instructions should be followed to ensure proper welding and safety.
For additional information, see American National Standard, Safety In Welding
And Cutting, and Z49.1. Avoid spreading dust.
Conditions for safe storage, including any incompatibilities
Technical measures for safe No special precautions.
storage:
Storage conditions: Store in tightly closed original container in a dry and cool place. Protect from
moisture.
Specific end use(s)
Specific use(s): Sealer.
SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 5/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
Control parameters
Occupational exposure limits:
CAS-No.: Chemical name: As: Exposure limits: Type: Notes: References
:
1303-96-4 Borates, tetra, sodium - 5 mg/m3 TWA - NIOSH
salts (Decahydrate)
1332-58-7 Kaolin, total particulate - 10 mg/m3 TWA - NIOSH
1332-58-7 Kaolin, respirable fraction - 5 mg/m3 TWA - NIOSH
- Kaolin, respirable fraction - 2 mg/m3 TWA A4 ACGIH
- Kaolin, total dust - 15 mg/m3 TWA - OSHA
- Kaolin, respirable fraction - 5 mg/m3 TWA - OSHA
Notes: A4: Not Classifiable as a Human Carcinogen.
ACGIH: Threshold Limit Values 2020 (ACGIH).
NIOSH: NIOSH Pocket Guide to Chemical Hazards (September 2007).
OSHA: Occupational Safety and Health Standards, Air contaminants
(amendments 2017).
Exposure controls
Engineering measures: Provide adequate ventilation. Observe Occupational Exposure Limits and
minimize the risk of inhalation of dust.
Personal protection: Protective gloves and goggles are recommended. Personal protection
equipment should be chosen according to the ANSI standards and in
discussion with the supplier of the personal protective equipment.
Respiratory equipment: No specific recommendation made, but respiratory protection must be used if
the general level exceeds the Recommended Occupational Exposure Limit.
Eye protection: Safety glasses recommended.
Skin protection: No special precautions.
Hygiene measures: Wash hands after handling. Change contaminated clothing. Wash
contaminated clothing before reuse.
SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 6/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Information on basic physical and chemical properties
Appearance: Solid.
Form: Dough-like
Odor: Dough-like
Odor threshold: Not available.
pH: Not available.
Melting point / freezing point: Not available.
Boiling point: Not available.
Flash point: Not available.
Evaporation rate: Not available.
Explosion limits: Not available.
Vapor pressure: Not available.
Vapor density: Not available.
Relative density: Not available.
Solubility: Slightly soluble in water.
Partition coefficient (n- Not available.
octanol/water):
Auto-ignition Not available.
temperature (°F):
Decomposition Not available.
temperature (°F):
Viscosity: Not available.
Oxidizing properties: Not available.
Other information
Other data: Specific Gravity (Water=1): 2.0
SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 7/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
SECTION 10: STABILITY AND REACTIVITY
Reactivity
Reactivity: Not reactive.
Chemical stability
Stability: Stable under normal temperature conditions.
Possibility of hazardous reactions
Hazardous Reactions: None known.
Conditions to avoid
Conditions/materials to avoid: Temperatures above ignition point.(1650°F)
Incompatible materials
Incompatible materials: None known.
Hazardous decomposition products
Hazardous decomposition Polymerization will not occur.
products:
SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 8/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
SECTION 11: TOXICOLOGICAL INFORMATION
Information on toxicological effects
Acute Toxicity (Oral): Based on available data, the classification criteria are not met.
Acute Toxicity (Dermal): Based on available data, the classification criteria are not met.
Acute Toxicity (Inhalation): Based on available data, the classification criteria are not met.
Skin Corrosion/Irritation: Based on available data, the classification criteria are not met.
Serious eye damage/irritation: Based on available data, the classification criteria are not met.
Respiratory or skin Based on available data, the classification criteria are not met.
sensitization:
Germ cell mutagenicity: Based on available data, the classification criteria are not met.
Carcinogenicity: Based on available data, the classification criteria are not met.
Reproductive Toxicity: Based on available data, the classification criteria are not met.
STOT - Single exposure: Based on available data, the classification criteria are not met.
STOT - Repeated exposure: Based on available data, the classification criteria are not met.
Aspiration hazard: Based on available data, the classification criteria are not met.
Inhalation: Dust may irritate throat and respiratory system and cause coughing.
Skin contact: Prolonged contact may cause redness, irritation and dry skin.
Eye contact: May irritate and cause redness and pain.
Ingestion: Ingestion may cause severe irritation of the mouth, the esophagus and the
gastrointestinal tract.
Specific effects: Frequent inhalation of dust over a long period of time increases the risk of
developing lung diseases. Contains small amounts of a substance which is
suspected to be harmful to the unborn child and to the reproduction capability.
(Borax)
This product contains no ingredient listed on the NTP, OSHA or IARC carcinogen
lists.
Information on other hazards
Endocrine disrupting The product does not contain any substance identified as having endocrine
properties: disrupting properties.
SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 9/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
SECTION 12: ECOLOGICAL INFORMATION
Toxicity
Ecotoxicity: The environmental hazard of the product is considered to be limited.
Persistence and degradability
Degradability: The product is not biodegradable.
Bioaccumulative potential
Bioaccumulative potential: No data available on bioaccumulation.
Mobility in soil
Mobility: The product is insoluble in water and will sediment in water systems.
Results of PBT and vPvB assessment
PBT/vPvB: This product does not contain any PBT or vPvB substances.
Endocrine disrupting properties
Endocrine disrupting The product does not contain any substance identified as having endocrine
properties: disrupting properties.
Other adverse effects
Other adverse effects: None known.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste treatment methods
Dispose of waste and residues in accordance with local authority requirements.
Reacted/Used Product - can be disposed of as a non-hazardous waste.
SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 10/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
SECTION 14: TRANSPORT INFORMATION
The product is not covered by international regulation on the transport of dangerous goods (IMDG, IATA, DOT).
UN number
UN-No: -
UN proper shipping name
Proper Shipping Name: -
Transport hazard class(es)
Class: -
Packing group
PG: -
Environmental hazards
Marine pollutant: -
Environmentally Hazardous -
substance:
Special precautions for user
Special precautions: Not relevant.
Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Transport in bulk: Not relevant.
SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 11/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
SECTION 15: REGULATORY INFORMATION
Safety, health and environmental regulations/legislation specific for the substance or mixture
Special provisions: State and local regulation may apply.
TSCA: The ingredients of this product are on the TSCA Inventory.
SARA Section 302: No.
SARA Section 304: No.
SARA Section 313: No.
NFPA Rating: Health:1 Fire:0 Reactivity:0 Other:-
National regulation: The following lists have been checked:
The Code of Federal Regulation, Title 29, part 1910. Occupational Safety and
Health Standards, Hazard Communication, with amendments.
Threshold Limit Values (2020), ACGIH, by the American Conference on
Governmental Industrial Hygienists.
The Code of Federal Regulation, Title 29, part 1910. Occupational Safety and
Health Standards, Air contaminants (OSHA), with amendments.
NIOSH Pocket Guide to Chemical Hazards.
U.S. Department of health and human services: 2016 - Report on Carcinogens -
14th Edition.
The Code of Federal Regulation. Title 40, part 355.50. Emergency Planning and
Notification.
The Code of Federal Regulation. Title 40, part 372.65. Toxic Chemical Release
Reporting: Community Right to Know.
International Agency for Research on Cancer (IARC): IARC Monographs on the
Evaluation of Carcinogenic Risks to Humans. Lyon: IARC, World Health
Organization.
SAFETY DATA SHEET
Product name: CADWELD® Mold Sealer (T403) Page: 12/12
Supersedes date: 2016-05-04 Revision: 2021-05-03
SDS-ID: CADWELD_MS_US Version number: US-EN/4.0
SECTION 16: OTHER INFORMATION
The user must be instructed in the proper work procedure and be familiar with the contents of these instructions.
The following sections contain revisions or new statements: 2, 3, 4, 8, 10, 11, 12, 13, 15, 16.
Abbreviations and acronyms
used in the safety data sheet: PBT = Persistent, Bioaccumulative and Toxic.
vPvB = very Persistent and very Bioaccumulative.
Additional information: Date of compilation: 2021.05.03
Wording of H-statements:
H360 May damage fertility or the unborn child.
The information on this data sheet represents our current data and is reliable provided that the product is used
under the prescribed conditions and in accordance with the application specified on the packaging and/or in the
technical guidance literature. Any other use of the product which involves using the product in combination with
any other product or any other process is the responsibility of the user.
