info@sandvik.

com
CONSTRUCTION.SANDVIK.COM

DTH TOOLS, PARTS AND KNOW-HOW

Art. no. DTHC10-6015ENG

FOR HASSLE-FREE DRILLING

1 2
 EXTENDING
LIFETIME
How to keep
your equipment in
tip-top shape.

11 CONTINUOUS
IMPROVEMENT
Innovations that
make life easier. 12
TROUBLE-
SHOOTING GUIDE
Identify and eliminate
common issues.

5 17
DTH DRILLING –
HERE’S THE LOW-DOWN
Tips and tricks for
smooth operations.

9
BUILDING ISTANBUL’S
WALL STREET
Sandvik equipment in action.

60
DRILL BITS THAT
TAKE YOU FURTHER
15
13
Designed for superior MASTERING
penetration. CEMENTED CARBIDES
Years of experience in
every insert.

76
DRILL PIPES
ZERO TOLERANCE

82
Engineered for a
long lifetime. OF FAILURE
ACCESSORIES R&D solves
For safer and easier challenges on site.
hammer operation.

20
HAMMERS THAT
DRIVE PRODUCTIVITY
High power with low
fuel consumption.

4
 DTH DRILLING –
HERE’S THE LOW-DOWN
Drilling holes in the ground is never completely trouble free, as anyone
who’s worked with DTH knows. However well-prepared you are, there can
always be surprises in store a few metres down.
Still, there’s a lot you can do to make life easier. And we are committed
to helping you. When it comes to drilling, we know what you’re up against.
That’s why we put such a big focus on R&D, making hammers and bits
better and better all the time. And that’s also why service and support
are top priorities for us.
What we do goes beyond advanced metals and high-tech products. It’s
about know-how. We’ve been working with DTH drilling for many years.
We know the applications, we know the challenges, and we know how to
get the best setup whatever the conditions.
So here’s a bit of know-how for you right here and now. Instead of just
printing a products and parts listing, we wanted to share some insight.
The tips you’ll find on these pages are things I’ve learned on job sites over
the years. It’s not rocket science, but then we’re not building rockets.
I hope they’re a good starting point anyway.
Got questions or need ways to drill better? Call Sandvik and use our
know-how.
Happy drilling!
Henrik Paues

THE ANSWER MAY BE CLOSER THAN YOU THINK

Avoid costly standstills and callouts! The operator instruction
manual that comes with your equipment contains detailed
information that will help you solve most issues quickly and easily.

Henrik Paues,
Application Specialist

5 6
 HASSLE-FREE DRILLING
STARTS WITH THE BASICS
Many potential problems in down-the-hole drilling can be avoided by taking
care to get the basics right. It comes down to the right tools and settings for
the conditions, and proper care of equipment. Here are my tips for drilling
further without hassle.

RIGHT FACE QUARRYING: CONSTRUCTION: WELL DRILLING:

First off, choose the right face THE RIGHT SETUP IS SIZE REALLY DOES NOT ALL ROCK DRILL OILS
design for the type of rock and EVERYTHING MATTER ARE THE SAME
your drilling priorities (e.g. tool Holes are relatively shallow in In construction applications, the One of the big problems here is the
lifetime, penetration rate, etc). quarrying applications, and holes can be anything from 3 use of cheap lubricants that don’t
Flat face works well for most accuracy is essential. That inches to 30 inches. The most meet the specification for rock
rock conditions and is especially demands a good setup. The drill common error is trying to drill too drill oil. Make sure whatever you’re
good in fractured, fissured needs to be centered, with the big a hole for the hammer. A 6 inch injecting into the airstream is what
and mixed rock formations. correct angle as required by the hammer is good from 6.25 inches your manufacturer recommends.
Concave face is the most drill and blast program. Build the to about 8 inches. Above that, you The requirements are determined
straightforward to operate and hole for the first few feet so it stays need a larger diameter hammer. by ambient temperature and
another good all-rounder, as open and nothing falls in. Stock the Using a bit that’s too big for the operating air temperature.
well as being particularly suited hole with water injection to build a hammer results in bit failure, slow
to deep hole drilling with high collar. Once you reach competent production, and a lot of frustration. Another key factor is the water
accuracy. Convex face gives a ground, you can go to full feed injected. This needs to be neutral
high penetration rate in softer to pressure, air pressure and rotation. A great many of the drilling or somewhat alkaline in order to
medium-hard rock. stoppages on construction sites prevent corrosion. When the hole
If you’re using multiple drill rods, are due to running out of fuel, oil is finished, flush the hammer out
RIGHT BIT
cover the lower rod when adding or water. Always do a walk-around with clean air and lubricate all parts
One of the most important issues a new one to keep contamination and check supplies before turning to maximize lifetime. After-drilling
when it comes to bit selection is out of the hammer. the drill on. maintenance is critical for deep-
choosing a bit large enough to hole applications.
allow cuttings to get around the
hammer and out of the hole. An Sandvik experts know the ground
undersized bit will slow you down,
as well as creating backpressure RIGHT SETTINGS
that shortens the life of carbides. Two of the biggest challenges TAKE 5 MINUTES
just the air pressure gauge on
It’s also important to start with in DTH drilling are feed pressure the drill and a stopwatch! First, Take five minutes before starting any task to consider any
the right carbide, bearing in mind and rotation. To get feed pressure gradually accelerate until you get potential hazards. Check you have everything you need to
that the tougher compounds can right, gradually increase until you an increase in penetration rate. do the job. Then do a quick risk assessment and decide what
extend the lifetime of the bit by 2-5 reach maximum operating air Continue until the penetration rate control measures are needed. Use this simple checklist:
times depending on the conditions. pressure. You now have optimum no longer increases. You have now • WHAT am I doing?
XT48 works for most drilling feed pressure and do not need to reached optimal rotation speed.
• WHY am I doing it?
conditions and should be the first increase further.
Carbide wear gives a good clue • WHAT could go wrong? Am I familiar with this task?
choice if there’s any uncertainty When it comes to rotation, it’s all to rotation. The wear should be Is my e quipment/tooling up to standard and safe?
about the rock type. DP65 is the about finding the happy medium. centered. A worn leading edge • HOW could this affect me and others?
right choice for hard, abrasive Too slow and productivity suffers. indicates too high rotation speed. Identify the hazards.
conditions, and DP55 in ballistic Too fast and you get excessive A worn trailing edge indicates the • WHAT can I do about it?
configurations gives fastest overall carbide wear. But there’s an easy speed is too low.
drilling in softer to medium-rock. way to find the right speed, using

7 8
 NIBU BORR
Swedish well driller Nibu Borr depends
on the quality of its equipment – and the
knowledge of its supplier. The RH460
hammer, and Nibu’s partnership with
Sandvik, has lifted performance.

OKIE DRILLING
Despite tough times, Okie Drilling in
Oklahoma has had eight years of
continuous growth. Okie believes it’s
down to the service focus of their people,
combined with Sandvik Construction’s
products and services.

BUILDING ISTANBUL’S SIZE

4.2 million m2

WALL STREET
COST
US$2.6 billion
PLAN
Four districts focusing on culture,
commerce, civic functions and governance.
A new financial district is being contracted for part of the foundation drilling.
LOCATION
constructed in vibrant Istanbul: the The company opted to use the RH460, and the
Between Ataşehir and Ümraniye districts,
Istanbul International Finance results have been little short of astonishing.
close to Istanbul’s historic centre.
Center. The US$2.6 billion
Fuel consumption was reduced by more than
development covers a 70 INFRASTRUCTURE CHANGES
50% compared to Terra Zemin’s previous
hectare site and is scheduled Transportation system incl. new subway line
hammer – 0.88 litres per minute compared to
for completion in 2016. The and station. Sustainable power, water, data
1.81 litres per minute.
Sandvik RH460 hammer is and security.
making its mark on the project. The RH460 also gave a 10% higher
SCHEDULED FOR COMPLETION
penetration rate.
Terra Zemin, a long-time Sandvik Late 2016
Construction customer, has been www.construction.sandvik.com

9 10
 EXTENDING CONTINUOUS
LIFETIME IMPROVEMENT
Our DTH hammers and tools are designed to give an outstanding service We constantly work on refining the technology in our hammers and bits
life. Give them proper care and they will still be going when others have long to help you do more and ensure you experience fewer problems. Every
given up. innovation is there for a reason – to remove the hassle in DTH drilling.

HAMMER MAINTENANCE STORING POWER YOU CAN DEPEND ON FUEL-SAVING DESIGN

Maintaining a hammer requires strict attention to Never allow a hammer and bit to remain overnight in a Our RH460 hammer is designed to give Lower air consumption means lower
safety due to the size and weight of the equipment and hole that contains water or mud. The corrosive action performance you can trust without fuel costs. The air cycle of the RH460
its parts. Remember also that even this tough piece caused by these conditions may seriously damage the question. However tough the conditions, hammer optimizes the expansion and
of equipment can be irreversibly damaged by bad hammer. Follow these points to protect components it simply won’t let you down. That’s what compression rate, giving more
maintenance practices. from rust and ensure the hammer is always ready for use. innovation means to us. power with less air.
• It is important to read the safety • Disassemble the hammer completely.
We have reduced air consumption for
procedures in the operator’s manual before
• Thoroughly clean and repair all components. lower fuel costs, boosted power for higher
assembling/disassembling the hammer.
• Reassemble the hammer immediately keeping productivity, and optimized lubrication for
• Always keep the hammer in the proper position
joints loose. longer piston and hammer life.
to avoid heavy parts falling out.
• Coat the entire hammer inside diameter with a
• Use a proper assembly stand to ensure the
light film of rock drill oil. Coat all the threads
hammer and its parts do not fall or roll over.
with thread grease.
• Always use tongs with jaws that place a uniform
• Install thread protectors.
load on the outside diameter of the hammer.

• Never grip the hammer with pipe wrenches

• Seal each end of the hammer to keep dirt and SMOOTH RUNNING
dust out.
or other wrenches that could deform or damage The special oil grooves in the RH460 piston
the hammer. • Always store the hammer in a suitable ensure constant and consistent lubrication
protective container in a dry location.
• Always place tongs on the body of the bit, not on between the piston and internal parts
the carbides. • Grease the bit shank. to reduce galling related failures.
• Do not apply heat to the piston case to remove • Place a protective cover on the bit to prevent They are also designed to help to
the driver sub or the top sub. foot valve breakage. ROCK SOLID minimize air leakage.
• Always store the bit in a dry location. The V-lock system is designed to prevent
• Before storing the hammer overnight or over the movement of the inner cylinder and
a weekend, clean the hammer by blowing air distributor, reducing galling-related
lubricated air through the system and insert failures. This simple design means
rock drill oil into top sub. Push the check valve
dart open with rounded end drift pin to ensure the oil
no tools are required for assembly or
inlet to the hammer. disassembly. The steel make-up ring
creates a constant make-up force,
independent of temperature and time.

NO VIBRATION
ACCESSORIES FOR SMOOTHER WORKING The piston bearing surface is designed
Sandvik has developed a comprehensive range of accessories and located for better bearing capabilities.
to make working with Sandvik hammers safer and smoother. It eliminates bending vibrations, which
These include hammer lifting bails, foot valve assembly and can result in galling failures.
disassembly tools and a comprehensive hammer service kit.
See page 86 for details

11 12
 ZERO TOLERANCE
OF FAILURE
We combine our R&D focus with a commitment to
solving our customers’ challenges. Spending a lot of time
out on site helps us gain a deep understanding of these
challenges. The end result: solutions that really work.

FROM DESIGN TO TESTING EFFECTIVE SIMULATIONS

Seemingly random premature fatigue GAVE THE ANSWER
failures in the drill bit have long Our R&D technicians and engineers Testing was carried out in cooperation
been an occupational hazard in rock visited several customers to get a with Okie Drilling Company, Inc.
drilling. But not any more. We set our Established in 2003 and based in
deeper understanding. The Applied
Stigler, Oklahoma, the company’s core
development team the task of solving Research team then ran calculations business is drilling for rock quarries
the mystery. Working closely with and tested various configurations and state road projects. It’s demanding
customers, they got to the bottom of to reduce stress levels in the drill work that requires efficient and reliable
this industry-wide issue and solved it bit. Using FE analysis for reliable equipment. Sandvik RH550 series
with a new drill bit design. hammers provide the performance Okie
simulations gave a clear indication
depends on to deliver.
of what caused the damage.
The challenge was that these failures
could occur at different stages Our team then worked on a new bit
in the drilling and under differing design and carried out extensive
conditions, with no clear reason for testing together with customers.
it to happen. We were determined to
find the answer. The results were excellent. The
original bits had an average service
To tackle the issue the team worked life of 1,500 metres, but we aimed to
on the entire process, from design to achieve 3,000 metres with the new
testing with customers. The first step design. In fact, the new bit design
was to investigate where the cracks reached an astonishing average of
initiated in the bit. 6,900 metres on the same drill sites.

The new design proved so effective

that it will be adopted across the
product range.

13 14
 MASTERING

PRECAUTIONS

CEMENTED CARBIDES
• Avoid formation and inhalation of dust. Wet grinding
is recommended.
• Always use adequate exhaust ventilation to limit
personal exposure to well below the occupational
exposure limits.
• Use respiratory protection if adequate ventilation is
Cemented carbides are a key to efficient and productive drilling. Whatever not available.
you’re doing, we can ensure the right grade for the task. We are a world • Use safety goggles, gloves, and suitable protective clothing.

leader in research and development for cemented carbides. That know- • IF INHALED: If breathing is difficult, remove victim to fresh
air and keep at rest in a position comfortable for breathing.
how goes into every bit you order. If experiencing respiratory symptoms: Call a POISON
CENTER or doctor/physician.

MATERIALS EXPERTISE GRINDING OF CEMENTED CARBIDE

We continue to develop new hard material alloys to Grinding or heating a cemented carbide product will
meet today’s industry challenges. Tool performance is produce dust or fumes of hazardous ingredients that
crucial when you’re dealing with harder rock and mineral can be inhaled, swallowed or come in contact with the HEALTH AND SAFETY INFORMATION MATERIAL
formations. The cemented carbide insert material’s skin or eyes. COMPOSITION
resistance to wear and fracturing is particularly important. Most hard metal products contain tungsten carbide and cobalt.
Cemented carbide contains two hazardous components:
Dual Property (DP) cemented carbides are our cobalt and tungsten carbide. Causes of exposure
patented grades. Their properties are tailored to Grinding or heating hard metal blanks or hard metal products will
Cobalt may cause sensitization through inhalation or
suit drilling conditions causing exceptional load or produce dust or fumes with dangerous ingredients that can be
skin contact. Inhalation or skin contact may also cause
cemented carbide wear. inhaled, swallowed or come in contact with the skin or eyes.
irritation. Sensitive persons may experience an allergic
reaction. Long-term inhalation of high concentrations may Acute toxicity
cause permanent respiratory disease. The dust is toxic when inhaled. Inhalation may cause irritation and
inflammation in the airways. Skin contact can cause irritation and
rash. Sensitized persons may experience an allergic reaction.
Chronic toxicity
Prolonged inhalation of high concentrations may cause lung
fibrosis or lung cancer. Cobalt is a potent skin sensitizer.
Repeated or prolonged contact can cause sensitization.

CLASSIFICATION
• The following hazard classification according to
GHS/CLP applies to the hard metal powder
(3%≤Co<10%):
• Acute Inhalation 3, H331: Toxic if inhaled.
• Carcinogenicity 1B, H350i: May cause cancer if inhaled.
• Repr. 2, H361f: Suspected of damaging fertility.
• STOT RE 1, H372: Causes damage to lungs through
prolonged or repeated exposure through inhalation.
XT48 DP55 DP65 • Resp. Sens. 1B, H334: May cause allergy or asthma
Sandvik’s stadard cemented This grade has wear resistance DP65 has similar toughness to symptoms or breathing difficulties if inhaled.
carbide grade for most drilling similar to XT48, but offers greater XT48, but considerably higher
• Skin Sens.1, H317: May cause an allergic skin reaction.
conditions. XT48 should be your toughness. It is especially wear resistance. This grade
• Aquatic Acute 1, H400: Very toxic to aquatic life.
first choice, especially when suited to ballistic inserts, should be your first choice when
drilling in rock that is not fully accommodating the higher loads drilling in very abrasive rock with • Aquatic Chronic 2, H411: Toxic to aquatic life with
known. Spherical XT48 inserts the insert may be exposed to large spherical inserts. long-lasting effects.
are optimized to withstand high because of the longer protrusion.
load and wear.

4 15 16
 TROUBLESHOOTING
GUIDE
Some of the most common problems encountered in DTH drilling
relate to rotation, feed force and bailing. Use this checklist as a starting
point for troubleshooting.

SYMPTOM: POSSIBLE CAUSE:

• Excessive vibration and high-pitched n
oise in the drill string
• Low penetration rate Feed force
• Joints become loose causing excessive heat generation and galling
• Premature failure of the bit (button pop-outs, excessive gage wear
too low
& r apid wear to the bit shank)
• Premature failure of the hammer (rapid wear to the driver sub splines)

SYMPTOM: POSSIBLE CAUSE:

• Drill string rotation becomes labored and uneven
• Noise from the drill string Feed force
• Low penetration rate
• Bending stress failures
too high
• Wear to all drill string components increases
• Jamming increases

SYMPTOM: POSSIBLE CAUSE:

• Jerky rotation
• Excessive vibration Rotation
• Low penetration rate
• Finer drill cuttings
speed too low
• Increased bit wear (especially on l eading edge of buttons)
• Button pop-outs
• Rapid wear to the bit shank and driver sub splines.

SYMPTOM:
• Excessive vibration
POSSIBLE CAUSE: ”The key to hassle-free drilling
• Low penetration rate Rotation is to make sure you have the
• Higher bit wear (especially to gage row buttons and adjacent
bit body steel)
speed too high
right bit, the right carbide
and the right settings for the
SYMPTOM: POSSIBLE CAUSE:
• Jamming increases
• Low penetration rate Incorrect
• Accumulation, and re-drilling, of cuttings in the hole
(finer drill cuttings)
bailing velocity conditions you’re dealing with.”
• Increased bit wear
• Increased wear to the hammer, d
rill pipes and bit body Henrik Paues, Application Specialist

4 17 18
 HAMMERS
THAT DRIVE
PRODUCTIVITY
Sandvik hammers combine high power and speed
with low fuel consumption. They are tried and
tested in demanding applications the world over.
RH460
The new RH460 hammer has been developed with a focus on improving
reliability and economy through cutting air consumption, increasing power
and improving lubrication. It gives higher impact energy with lower levels of
air consumption, giving high productivity in variable ground conditions.

RH550
The RH550 is the first choice for drilling hard and abrasive rocks and is
designed for operating pressures from 10-24 bar. It features a patented
shank design for optimized energy efficiency, and no foot valve. Models are
available with heavy-duty or reversible casings to ensure maximal life in high-
speed drilling applications in abrasive rock formations.

RH350
The RH350 is a lean and dependable hammer based on a well-proven design.
This hammer works with various industry-standard shank designs. The RH350
is suitable when drilling holes with a diameter of 244 mm up to 900 mm.

RH550 COMPLETE HAMMERS 21

RH550 REPLACEMENT PARTS 25

RH460 COMPLETE HAMMERS 37

RH460 REPLACEMENT PARTS 41

RH350 COMPLETE HAMMERS 51

RH350 REPLACEMENT PARTS 53

19 20
RH550r 3" Replacement parts Item description
Complete hammer
Part No.
RH550g 5" Replacement parts Item description
Complete Hammer
Part No.

2 3/8" API reg. pin top sub 32-5530-RMA/16S   3 1/2" API reg. pin top sub 32-5555-GMA/04C
#21 Cubex. pin top sub 32-5530-RMA/63S   #24 Cubex. pin top sub 32-5555-GMA/77C

Bit shank Bit shank

M30   M50

Hammer length with bit Hammer length with bit

Weight Outside diameter Hammer length Weight Outside diameter Hammer length
Bit closed Bit extended Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch kg lb mm inch mm inch mm inch mm inch

25 55 81.3 3.2 823 32.4 875 34.4 911 35.9 73 160 126 4.96 987 38.86 1082 42.6 1122 44.2

Air consumption, cfm Air consumption, m³/min Air consumption, cfm Air consumption, m³/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

172 304 436 4.87 8.61 12.34 305 580 855 8.64 16.42 24.21

Low Volume Option 285 540 790 8.07 15.25 22.37

RH550r 4" Replacement parts Item description

Complete Hammer
Part No.
RH550r 5" Replacement parts Item description Part No.
Complete Hammer
2 3/8" API reg. pin top sub 32-5540-RMA/16S
3 1/2" API reg. pin top sub 32-5555-RMA/04C
2 7/8" API reg. pin top sub 32-5540-RMA/11S
2 7/8" API reg. pin top sub 32-5555-RMA/11C
#24 Cubex. pin top sub 32-5540-RMA/77S
#24 Cubex. pin top sub 32-5555-RMA/77C

Bit shank
Bit shank
M40
M50

Hammer length with bit

Weight Outside diameter Hammer length Hammer length with bit
Bit closed Bit extended Weight Outside diameter Hammer length
Bit closed Bit extended
kg lb mm inch mm inch mm inch mm inch
kg lb mm inch mm inch mm inch mm inch
38 83 98 3.56 914 36 989 38.9 1029 40.5
73 160 126 4.96 987 38.86 1082 42.6 1122 44.2
Air consumption, cfm Air consumption, m³/min
Air consumption, cfm Air consumption, m³/min
150 psi 250 psi 350 psi 10 bar 18 bar 24 bar
150 psi 250 psi 350 psi 10 bar 18 bar 24 bar
180 370 560 5.1 10.5 15.9
305 580 855 8.64 16.42 24.21
Low Volume Option 151 315 466 4.3 8.9 13.2
Low Volume Option 285 540 790 8.07 15.25 22.37

RH550 5" Replacement parts Item description

Complete Hammer
Part No.
RH550 6" Replacement parts Item description
Complete hammer
Part No.

3 1/2" API reg. pin top sub 32-5550-SMA/04S 3 1/2" API reg. pin top sub 32-5560-SMA/04S
2 7/8" API reg. pin top sub 32-5550-SMA/11S
Bit shank
Bit shank M60
M50

Hammer length with bit Hammer length with bit

Weight Outside diameter Hammer length Weight Outside diameter Hammer length
Bit closed Bit extended Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch kg lb mm inch mm inch mm inch mm inch

68 145 120 4.72 987 38.86 1082 42.6 1122 44.2 72 158 142 5.6 922 36.3 1008 39.7 1046 41.2

Air consumption, cfm Air consumption, m³/min Air consumption, cfm Air consumption, m³/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

305 580 855 8.64 16.42 24.21 343 659 972 9.8 18.7 27.5

Low Volume Option 285 540 790 8.07 15.25 22.37

21 22
RH550g 6" Replacement parts Item description
Complete hammer
Part No.
RH550r 8" Replacement parts Item description
Complete Hammer
Part No.

  3 1/2" API reg. pin top sub 32-5565-GMA/04C 4 1/2" API reg. pin top sub 32-5585-RMA/19C
  #28 Cubex. pin top sub 32-5565-GMA/56C
Bit shank
Bit shank M80
M60

Hammer length with bit Hammer length with bit

Weight Outside diameter Hammer length Weight Outside diameter Hammer length
Bit closed Bit extended Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch kg lb mm inch mm inch mm inch mm inch

82 180 150 5.9 922 36.3 1008 39.7 1046 41.2 173 380 181 7.12 1219 48 1310 51.6 1354 53.3

Air consumption, cfm Air consumption, m³/min Air consumption, cfm Air consumption, m³/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

343 659 972 9.8 18.7 27.5 460 850 1240 13 23.8 35.1

Low Volume Option 300 560 830 08.05 15.9 23.5

RH550r 6" Replacement parts Item description

Complete hammer
Part No.

RH550w 8" Replacement parts Item description Part No.

Complete Hammer
3 1/2" API reg. pin top sub 32-5565-RMA/04C
4 1/2" API reg. pin top sub 32-5585-WMA/19S
#28 Cubex. pin top sub 32-5565-RMA/56C
3 1/2" BECO. pin top sub 32-5565-RMA/55C
Bit shank
M80
Bit shank
M60

Hammer length with bit

Hammer length with bit Weight Outside diameter Hammer length
Weight Outside diameter Hammer length Bit closed Bit extended
Bit closed Bit extended
kg lb mm inch mm inch mm inch mm inch
kg lb mm inch mm inch mm inch mm inch
173 380 181 7.12 1270 50 1361 53.6 1405 55.3
82 180 150 5.9 922 36.3 1008 39.7 1046 41.2
Air consumption, cfm Air consumption, m³/min
Air consumption, cfm Air consumption, m³/min
150 psi 250 psi 350 psi 10 bar 18 bar 24 bar
150 psi 250 psi 350 psi 10 bar 18 bar 24 bar
525 975 1540 14.9 27.6 43.6
343 659 972 9.8 18.7 27.5

RH550w 6" Replacement parts Item description

Complete hammer
Part No.

3 1/2" API reg. pin 32-5560-WMA/04S

Bit shank
M60

Hammer length with bit

Weight Outside diameter Hammer length
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

72 158 142 5.6 922 36.3 1008 39.7 1046 41.2

Air consumption, cfm Air consumption, m³/min

150 psi 250 psi 350 psi 10 bar 18 bar 24 bar

395 759 1120 11.2 21.5 31.7

Low volume option 345 680 1000 9.8 19.3 28.3

23 24
RH550r 3" RH550r 4"

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top subs 1. Top subs with 3 O-rings
2 3/8" API reg. pin 5 11 33-3A001/16A 2 3/8" API reg. pin 10 22 33-48001-1/16A
#21 Cubex. pin 5 11 33-3A001/63A 2 7/8" API reg. pin 10 22 33-48001-1/11A
2. O-ring top sub (3) ID and OD In seal kit 1 #24 Cubex. pin 10 22 33-48001-1/77A
1
3. Check valve dart with spring 0.3 0.7 25-99006A 2. O-ring top sub OD (1) In seal kit
4. Check valve dart spring 0.02 0.01 22-99071 3. O-ring top sub ID (2) In seal kit
5. Check valve guide 0.23 0.5 39-3A001 4. Check valve dart (with spring) 0.3 0.66 25-99001A
6. Feed tube retainer pin 0.03 0.1 12-99021 5. Check valve spring 0.02 0.04 22-99071
7. Choke set, blank 1/8", 3/16", & 1/4" 0.1 0.2 29-48017A 6. Check valve guide 0.2 0.44 39-48001-1
2
2 8. Feed tube with retainer pin & 7. Choke set, blank 1/8", 3/16", & 1/4" 0.1 0.22 29-48017A
0.45 1 37-3A001A 3
blank choke 12 8. Feed tube retainer pin 0.03 0.07 12-99014
9. Piston 3.86 8.5 36-3A081 9. Tuning ring for low volume (optional) 0.23 0.51 56-48552
3 10. Piston case with retainer ring 10.9 24 35-3A006A 4 10. Feed tube with retainer pin and
0.7 1.54 37-48001-1A
11. Piston retainer ring 0.05 0.1 23-99027 blank choke
4 5
12. O-rings – guide sleeve, bit retainer (3) In seal kit 11. Piston 7 15.4 36-48J81

5 13. Guide sleeve with 2 O-rings (#12) 1 2.2 26-3A010A 12. Piston case with retainer ring 15 33 35-48014A
6
10 14. Bit retainer ring with O-ring (#12) 0.09 0.2 27-3A006A 13. Piston retainer ring 0.05 0.11 23-99029
6 15. Driver sub (O-ring not req.) 2.18 4.8 34-3A006 14. O-rings guide sleeve & bit ret. (3) In seal kit
15. Guide sleeve with 2 O-rings (#14) 1.8 3.96 26-48J10A
13
7 Seal Kit 7 16. Bit retainer ring with O-ring (#14) 0.23 0.51 27-48006A
3 piece of #2 & 3 of #12 0.25 0.5 38-3A056 14 17. Driver sub 3.2 7.04 34-48006
8

Rebuild Kit Seal Kit

9 15
1 piece of #1, 1 of #10, 1 of #15 & seal kit 1 piece of #2, 2 of #3 & 3 of #14 0.25 0.5 38-48056-1

11 2 3/8" API reg. pin 18.1 40 38-3A001/16

8 #21 Cubex. pin 18.1 40 33-3A001/63 Rebuild Kit
12 10 14
1 piece of #1, 1 of #12, 1 of #17 & seal kit
16
2 3/8" API reg. pin 28 62 38-48001/16
13 2 7/8" API reg. pin 28 62 38-48001/11
17 #24 Cubex. pin 28 62 38-48001/77

12
14 11
9

15

25 26
RH550 5" RH550g 5"

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top subs with 3 O-rings 1. Top subs with 3 O-rings
3 1/2" API reg. pin 10 22 33-58D01/04A 3 1/2" API reg. pin 18 39.6 33-58D02/04CA
2 7/8" API reg. pin 10 22 33-58D01/11A #24 Cubex. pin 18 39.6 33-58D02/77CA
1 2. O-ring top sub OD (1) In seal kit 1 2. O-ring top sub OD (1) In seal kit
3. O-ring top sub ID (2) In seal kit 3. O-ring top sub ID (2) In seal kit
4. Check valve dart (with spring) 0.3 0.66 25-99002A 4. Check valve dart (with spring) 0.3 0.66 25-99002A
5. Check valve spring 0.02 0.04 22-99072 5. Check valve spring 0.02 0.04 22-99072

2 6. Check valve guide 0.3 0.66 39-58S01 2 6. Check valve guide 0.3 0.66 39-58S01
7. O-Ring feed tube (1) In seal kit 7. Choke set, blank 1/8", 3/16", & 1/4" 0.12 0.26 29-68017A
3 3
8. Choke set, blank 1/8", 3/16", & 1/4" 0.12 0.26 29-68017A 8. O-ring feed tube (1) In seal kit
9. Feed tube retainer pin 0.09 0.2 12-99018 9. Feed tube retainer pin 0.09 0.2 12-99018
4 4
10. Feed tube with retainer pin and 10. Feed tube with retainer pin and
1 2.2 37-58001A 1 2.2 37-58001A
blank choke blank choke

11. Tuning ring for low volume (optional) 0.03 0.07 56-58552 13 11. Tuning ring for low volume (optional) 0.03 0.07 56-58552
5 13 5
12. Piston 12 26.4 36-58J81 12. Piston 12 26.4 36-58J81
13. Piston case with retainer ring 27 59.4 35-58D06A 13. Piston case with retainer ring 29 63.8 35-58D07A

6 14. Piston retainer ring 0.05 0.11 23-99032 6 14. Piston retainer ring 0.05 0.11 23-99032
15. O-rings guide sleeve & bit ret. (3) In seal kit 15. O-rings guide sleeve & bit ret. (3) In seal kit
16. Guide sleeve with 2 O-rings (#14) 3 6.6 26-58J10A 16. Guide sleeve with 2 O-rings (#14) 3 6.6 26-58J10A
17. Bit retainer ring with O-ring (#14) 0.5 1.1 27-58006A 17. Bit retainer ring with O-ring (#14) 0.5 1.1 27-58006A
7 18. Driver sub 6 13.2 34-58D69 7 18. Driver sub 7 15.4 34-58D70
8 8
9 14 9 14
10 15 Seal Kit
10 15 Seal Kit
1 piece of #2, 2 of #3, 1 of #7 & 3 of #15 0.45 0.99 38-58D56 1 piece of #2, 2 of #3, 1 of #7 & 3 of #15 0.45 0.99 38-58D56

11 11
16 Rebuild Kit 16 Rebuild Kit
1 piece of #1, 1 of #13, 1 of #18 & seal kit 1 piece of #1, 1 of #13, 1 of #18 & seal kit
  3 1/2" API reg. pin 43 94.6 38-58D01/04 15   3 1/2" API reg. pin 54 118.8 38-58D02/04C
15 17
  2 7/8" API reg. pin 43 94.6 38-58D01/11   #24 Cubex. pin 54 118.8 38-58D02/77C
15
12 17
12
18 18

27 28
RH550r 5" RH550 6"

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top subs with 3 O-rings 1. Top sub with 3 O-rings
3 1/2" API reg. pin 18 39.6 33-58S02/04CA   3 1/2" API reg. pin 20 44 33-68D08/04A
2 7/8" API reg. pin 18 39.6 33-58S02/11CA 2. O-ring top sub OD (1) In seal kit
1 1
#24 Cubex. pin 18 39.6 33-58S02/77CA 3. O-ring top sub ID (2) In seal kit
2. O-Ring top sub OD (1) In seal kit 4. Check valve dart with spring 0.3 0.66 25-99002A
3. O-Ring top sub ID (2) In seal kit 5. Check valve dart spring 0.02 0.044 22-99072
4. Check valve dart (with spring) 0.3 0.66 25-99002A 6. Check valve guide 0.3 0.66 39-68001

2 5. Check valve spring 0.02 0.04 22-99072 7. Choke set, blank 1/8", 3/16", & 1/4" 0.12 0.264 29-68017A
2
6. Check valve guide 0.3 0.66 39-58S01 8. Feed tube retainer pin 0.2 0.44 12-99013
3 3
7. Choke set, blank 1/8", 3/16", & 1/4" 0.12 0.26 29-68017A 9. Feed tube with retainer pin and
1 2.2 37-68601A
8. O-ring feed tube (1) In seal kit blank choke
4 9. Feed tube retainer pin 0.09 0.2 12-99018 10. Piston 18 39.6 36-68J81
4
10. Feed tube with retainer pin and 11. Piston case with retainer ring 33 72.6 35-68D14A
1 2.2 37-58001A
blank choke 12. Piston retainer ring 0.1 0.22 23-99028
5 13
11. Tuning ring for low volume (optional) 0.03 0.07 56-58552 13. O-rings – guide sleeve, bit retainer (3) In seal kit
5
12. Piston 12 26.4 36-58J81 14. Guide sleeve with 2 O-rings (#13) 4 8.8 26-68J10A
6 13. Piston case with retainer ring 29 63.8 35-58007A
11 15. Bit retainer ring with O-ring (#13) 1 2.2 27-68006A
14. Piston retainer ring 0.05 0.11 23-99032 16. Driver sub 6 13.2 34-68D69
6
15. O-rings guide sleeve & bit ret. (3) In seal kit
16. Guide sleeve with 2 O-rings (#14) 3 6.6 26-58J10A Seal Kit
7 17. Bit retainer ring with O-ring (#14) 0.5 1.1 27-58006A 1 piece of #2, 2 of #3 & 3 of #13 0.25 0.55 38-68656
8 18. Driver sub 7 15.4 34-58070 7
9 14
15 Seal Kit 12 Rebuild Kit
10
1 piece of #2, 2 of #3, 1 of #7 & 3 of #15 0.45 0.99 38-58D56 1 piece of #1, 1 of #11, 1 of #16 & seal kit
8 13
Rebuild Kit 3 1/2" API reg. pin 20 44 38-68D08/04
11
16 1 piece of #1, 1 of #13, 1 of #18 & seal kit
9
3 1/2" API reg. pin 54 118.8 38-58S02/04C 14
15 2 7/8" API reg. pin 54 118.8 38-58S02/11C
17 #24 Cubex. pin 54 118.8 38-58S02/77C
15 13
12 15
18 13

10 16

29 30
RH550g 6" RH550r 6"

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top sub with 3 O-rings 1. Top sub with 3 O-rings
  3 1/2" API reg. pin 22 48.4 33-6L009/04CA   3 1/2" API reg. pin 22 48.4 33-68602/04CA
  #28 Cubex. pin 22 48.4 33-6L009/56CA 1   #28 Cubex. pin 22 48.4 33-68602/56CA
1
2. O-ring top sub OD (1) In seal kit   3 1/2" BECO. pin 22 48.4 33-68602/55CA
3. O-ring top sub ID (2) In seal kit 2. O-ring top sub OD (1) In seal kit
4. Check valve dart with spring 0.3 0.66 25-99002A 3. O-ring top sub ID (2) In seal kit
5. Check valve dart spring 0.02 0.044 22-99072 4. Check valve dart with spring 0.3 0.66 25-99002A

2 6. Check valve guide 0.3 0.66 39-68001 2 5. Check valve dart spring 0.02 0.044 22-99072
7. Choke set, blank 1/8", 3/16", & 1/4" 0.12 0.264 29-68017A 6. Check valve guide 0.3 0.66 39-68001
3 3
8. Feed tube retainer pin 0.2 0.44 12-99013 7. Choke set, blank 1/8", 3/16", & 1/4" 0.12 0.264 29-68017A

9. Feed tube with retainer pin and 8. Feed tube retainer pin 0.2 0.44 12-99013
1 2.2 37-68601A
blank choke
4 4 9. Feed tube with retainer pin and
1 2.2 37-68601A
10. Piston 18 39.6 36-68J81 blank choke

11. Piston case with retainer ring 33 72.6 35-6LD68A 10. Piston 18 39.6 36-68J81
12. Piston retainer ring 0.1 0.22 23-99028 11. Piston case with retainer ring 33 72.6 35-68668A
5 5
13. O-rings – guide sleeve, bit retainer (3) In seal kit 12. Piston retainer ring 0.1 0.22 23-99028
11 11
14. Guide sleeve with 2 O-rings (#13) 4 8.8 26-68J10A 13. O-rings – guide sleeve, bit retainer (3) In seal kit

6 15. Bit retainer ring with O-ring (#13) 1 2.2 27-68006A 6 14. Guide sleeve with 2 O-rings (#13) 4 8.8 26-68J10A
16. Driver sub 6 13.2 34-6LD70 15. Bit retainer ring with O-ring (#13) 1 2.2 27-68006A
16. Driver sub 6 13.2 34-68670
Seal Kit
7 7
1 pieces of #2, 2 of #3 & 3 of #13 0.25 0.5 38-68656 Seal Kit
12 12 1 pieces of #2, 2 of #3 & 3 of #13 0.25 0.5 38-68656

8 Rebuild Kit 8
13 13
1 piece of #1, 1 of #11, 1 of #16 & seal kit Rebuild Kit

9   3 1/2" API reg. pin 62 136.4 38-6LD09/04C 9 1 piece of #1, 1 of #11, 1 of #16 & seal kit
14   #28 Cubex. pin 62 136.4 38-6LD09/56C 14   3 1/2" API reg. pin 62 136.4 38-68602/04C
  #28 Cubex. pin 62 136.4 38-68602/56C
  3 1/2" BECO. pin 62 136.4 38-68602/55C
13 13

15 15
13 13

10 10 16
16

31 32
RH550w 6" RH550r 8"

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top sub with 3 O-rings 1. Top sub with 3 O-rings
  3 1/2" API reg. pin 20 44 33-68N08/04A   4 1/2" API reg. pin 42 92.4 33-88002/19CA
1 2. O-ring top sub OD (1) In seal kit 2. O-ring top sub OD (1) In seal kit
3. O-ring top sub ID (2) In seal kit 3. O-ring top sub ID (2) In seal kit
1
4. Check valve dart with spring 0.3 0.66 25-99002A 4. Check valve dart (with spring) 0.5 1.1 38-11663A
5. Check valve dart spring 0.02 0.044 22-99072 5. Check valve spring 0.1 0.22 38-1/1235-073
6. Check valve guide 0.3 0.66 39-68001 6. Check valve guide 0.7 1.54 39-88001
2 2
7. Choke set, blank 1/8", 3/16", & 1/4" 0.12 0.264 29-68017A 7. Choke set, blank 1/8", 3/16", & 1/4" 0.12 0.264 29-68017A
3 12-99013 12-99016
8. Feed tube retainer pin 0.2 0.44 3 8. Feed tube retainer pin 0.2 0.44
9. Tuning ring (optional) 0.4 0.9 56-68552 9. Tuning ring for low volume (optinal) 0.8 1.76 56-88552

10. Feed tube with retainer pin and 10. Feed tube with retainer pin and
4 1 2.2 37-68301A 2.2 4.84 37-88001A
blank choke 4 blank choke

11. Piston 18 39.6 36-68J81 11. Piston 42 92.4 36-88J81

12. Piston case with retainer ring 33 72.6 35-68D14A 12. Piston case with retainer ring 56 123.2 35-88002A
5 13. Piston retainer ring 0.1 0.22 23-99028 5 13. Piston retainer ring 0.2 0.44 23-99030
12
12 14. O-rings – guide sleeve, bit retainer 14. O-rings guide sleeve & bit ret. (3) In seal kit
In seal kit
(3 req.) 15. Guide sleeve with 2 O-rings (#14) 11 24.2 26-88J10A
6 15. Guide sleeve with 2 O-rings (#13) 4 8.8 26-68J10A 6 16. Bit retainer ring with O-ring (#14) 1.9 4.18 27-88006A
16. Bit retainer ring with O-ring (#13) 1 2.2 27-68006A 17. Driver sub 17 37.4 34-88007
17. Driver sub 6 13.2 34-68D69
7
Seal Kit
7
Seal Kit 13 1 piece of #2, 2 of #3 & 3 of #14 0.25 0.55 38-88056
1 pieces of #2, 2 of #3 & 3 of #14 0.25 0.5 38-68656 14
8 13 8
Rebuild Kit
9 14 Rebuild Kit 9 1 piece of #1, 1 of #12, 1 of #17 & seal kit
1 piece of #1, 1 of #12, 1 of #17 & seal kit 10 15 4 1/2" API reg. pin 115 253 38-88002/19C
15   3 1/2" API reg. pin 20 44 38-68N08/04
10
14
14 16
16 14
14
11 17
17
11

33 34
RH550w 8"

Replacement parts Item description Weight Part No.

kg lb
1. Top sub with 3 O-rings
  4 1/2" API reg. pin 42 92.4 33-88302/19A
2. O-ring top sub OD (1) In seal kit
1
3. O-ring top sub ID (2) In seal kit
4. Check valve dart (with spring) 0.5 1.1 38-11663A
5. Check valve spring 0.1 0.22 38-1/1235-073
2 6. Check valve guide 0.7 1.54 39-88001
7. Choke set, blank 1/8", 3/16", & 1/4" 0.12 0.26 29-68017A
3
8. Feed tube retainer pin 0.2 0.44 12-99016

9. Feed tube with retainer pin and

2.2 4.84 37-88301A
blank choke
4
10. Piston 42 92.4 36-88J81
11. Piston case with retainer ring 56 123.2 35-88302A
12. Piston retainer ring 0.2 0.44 23-99030
5
13. O-rings guide sleeve & bit ret. (3) In seal kit

11 14. Guide sleeve with 2 O-rings (#14) 11 24.2 26-88J10A

15. Bit retainer ring with O-ring (#14) 1.9 4.18 27-88006A
6
16. Driver sub 17 37.4 34-88007

Seal Kit
7 1 piece of #2, 2 of #3 & 3 of #13 0.25 0.55 38-88056
12
8
13 Rebuild Kit
1 piece of #1, 1 of #11, 1 of #16 & seal kit
14
9 4 1/2" API reg. pin 115 253 38-88302/19

13
15

10 16

35 36
RH460 4" Replacement parts Item description
Complete Hammer
Part No.
RH460 5" Replacement parts Item description
Complete Hammer
Part No.

2 3/8" API reg pin 32-4640-SDA-16S 3 1/2" API reg pin 32-4650-SQA-04S
#24 Cubex pin 32-4640-SDA-77S
Bit shank
Bit shank QL50
DHD340

Hammer length with bit Hammer length with bit

Weight Outside diameter Hammer length Weight Outside diameter Hammer length
Bit closed Bit extended Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch kg lb mm inch mm inch mm inch mm inch

40 88 97.5 3.84 985 38.78 1075 42.16 1109 43.66 66 145 120 4.72 1067 42.01 1156 45.51 1185 46.65

Air consumption, cfm Air consumption, m³/min, DIN 1343 Power output [kW] Air consumption, cfm Air consumption, m³/min, DIN 1343 Power output [kW]
150 psi 250 psi 350 psi 10 bar 18 bar 24 bar 24 bar 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar 24 bar

177 399 565 5 11.3 16 23.5 286 540 770 8.1 15.3 21.8 32.1

RH460 4" Replacement parts Item description

Complete Hammer
Part No.
RH460g 5" Replacement parts Item description
Complete Hammer
Part No.

2 3/8" API reg pin 32-4640-STA-16S 3 1/2" API reg pin 32-4655-GQA-04C
#24 Cubex pin 32-4640-STA-77S #24 Cubex pin 32-4655-GQA-77C

Bit shank Bit shank

QLX40 QL50

Hammer length with bit Hammer length with bit

Weight Outside diameter Hammer length Weight Outside diameter Hammer length
Bit closed Bit extended Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch kg lb mm inch mm inch mm inch mm inch

40 88 97.5 3.84 985 38.78 1075 42.16 1109 43.66 76 167 126 4.96 1067 42.01 1156 45.51 1185 46.65

Air consumption, cfm Air consumption, m³/min, DIN 1343 Power output [kW] Air consumption, cfm Air consumption, m³/min, DIN 1343 Power output [kW]
150 psi 250 psi 350 psi 10 bar 18 bar 24 bar 24 bar 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar 24 bar

177 399 565 5 11.3 16 23.5 286 540 770 8.1 15.3 21.8 32.1

RH460hp 4" Replacement parts Item description

Complete Hammer
Part No.
RH460hp 5" Replacement parts Item description
Complete Hammer
Part No.

2 3/8" API reg pin 32-4640-ETB-16S 3 1/2" API reg pin 32-4655-EQB-04C

Bit shank Bit shank

QLX40 QL50

Hammer length with bit Hammer length with bit

Weight Outside diameter Hammer length Weight Outside diameter Hammer length
Bit closed Bit extended Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch kg lb mm inch mm inch mm inch mm inch

41 90 97.5 3.84 985 38.78 1075 42.16 1109 43.66 76 168 126 4.96 1067 42.01 1156 45.51 1185 46.65

Air consumption, cfm Air consumption, m³/min, DIN 1343 Power output [kW] Air consumption, cfm Air consumption, m³/min, DIN 1343 Power output [kW]
250 psi 350 psi 500 psi 18 bar 24 bar 35 bar 35 bar 250 psi 350 psi 500 psi 18 bar 24 bar 35 bar 35 bar

364 519 805 10.3 14.7 22.8 32 501 692 1102 14.2 19.6 31.2 41.6

37 38
RH460 6" Replacement parts Item description
Complete Hammer
Part No.
RH460g 8" Replacement parts Item description
Complete Hammer
Part No.

3 1/2" API reg pin 32-4660-SQA-04S 4 1/2" API reg pin 32-4685-GQA-19C
4 1/2 BECO pin 32-4685-GQA-72C
Bit shank
QL60 Bit shank
QL80

Hammer length with bit Hammer length with bit

Weight Outside diameter Hammer length Weight Outside diameter Hammer length
Bit closed Bit extended Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch kg lb mm inch mm inch mm inch mm inch

100 220 142 5.59 1155 45.47 1263 49.72 1304 51.34 244 537 194 7.64 1426 56.14 1566 61.65 1608 63.31

Air consumption, cfm Air consumption, m³/min, DIN 1343 Power output [kW] Air consumption, cfm Air consumption, m³/min, DIN 1343 Power output [kW]
150 psi 250 psi 350 psi 10 bar 18 bar 24 bar 24 bar 150 psi 250 psi 350 psi 10 bar 18 bar 24 bar 24 bar

300 632 879 8.5 17.9 25 41.7 314 862 1274 8.9 24.4 36 49.7

RH460g 6" Replacement parts Item description

Complete Hammer
Part No.

3 1/2" API reg pin 32-4665-GQA-04C

#28 Cubex pin 32-4665-GQA-56C

Bit shank
QL60

Hammer length with bit

Weight Outside diameter Hammer length
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

117 257 150 5.91 1155 45.47 1263 49.72 1304 51.34

Air consumption, cfm Air consumption, m³/min, DIN 1343 Power output [kW]
150 psi 250 psi 350 psi 10 bar 18 bar 24 bar 24 bar

300 632 879 8.5 17.9 25 41.7

RH460 8" Replacement parts Item description

Complete Hammer
Part No.

4 1/2" API reg pin 32-4680-SQA-19S

Bit shank
QL80

Hammer length with bit

Weight Outside diameter Hammer length
Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch

213 469 183 7.20 1426 56.14 1566 61.65 1608 63.31

Air consumption, cfm Air consumption, m³/min, DIN 1343 Power output [kW]
150 psi 250 psi 350 psi 10 bar 18 bar 24 bar 24 bar

314 862 1274 8.9 24.4 36 49.7

39 40
RH460 4" RH460 4"

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top sub 1. Top sub
2 3/8" API reg pin 8.2 18 BG00014822 2 3/8" API reg pin 8.2 18. BG00014822
#24 Cubex pin 7.9 17.4 BG00242018 #24 Cubex pin 7.9 17.4 BG00242018
1 1
2 7/8” API reg pin 8.8 19.4 BG00388091 2 7/8” API reg pin 8.8 19.4 BG00388091
2. Check valve dart no choke 0.24 0.53 BG00320005 2. Check valve dart no choke 0.24 0.53 BG00320005
3. Check valve spring 0.02 0.04 BG00118911 3. Check valve spring 0.02 0.04 BG00118911
4. Make up ring 0.1 0.22 BG00014825 4. Make up ring 0.1 0.22 BG00014825
2 2
5. Air distributor with O-ring 2 4.4 BG00056811 5. Air distributor with O-ring 2 4.4 BG00056811
6. O-ring air distributor In seal kit 6. O-ring air distributor In seal kit

3 7. Inner cylinder 2.1 4.62 BG00110688 3 7. Inner cylinder 2.1 4.62 BG00110688
8. Piston DHD340 7.8 17.2 BG00243036 8. Piston QLX40 7.7 16.9 BG00242889

4 9. Piston case with retainer ring 15.4 33.9 BG00050403 4 9. Piston case with retainer ring 15.4 33.9 BG00050403
10. Piston retainer ring 0.1 0.22 BG00014819 10. Piston retainer ring 0.1 0.22 BG00014819
11. Bit retainer ring with O-ring DHD340 0.17 0.37 BG00014818 11. Bit retainer ring with O-ring QLX40 0.2 0.44 BG00059039

5 9 12. O-ring bit retainer ring In seal kit 5 9 12. O-ring bit retainer ring In seal kit
13. Driver sub 3.5 7.7 BG00059100 13. Driver sub 2.8 6.16 BG00058997

Optional Optional

Air screen 0.05 0.11 BG00014743 Air screen 0.05 0.11 BG00014743

Air screen circlip 0.01 0.02 BG00014740 Air screen circlip 0.01 0.02 BG00014740

6 Choke set, blank, 3mm, 4.5mm and 6mm 0.02 0.04 BG00015430 6 Choke set, blank, 3mm, 4.5mm and 6mm 0.02 0.04 BG00015430

Check valve dart with choke hole 0.24 0.53 BG00119068 Check valve dart with choke hole 0.24 0.53 BG00119068

Driver sub hard faced DHD340 3.5 7.7 BG00241988 Driver sub hard faced QLX40 2.8 6.16 BG00242001
10 10

Seal Kit Seal Kit

11 11 1 piece of #6, #12 0.02 0.04 BG00014848
1 piece of #6, #12 0.02 0.04 BG00014848

7 7
12 12
Rebuild Kit Rebuild Kit

1 piece of #1, #9, #13 & seal kit 1 piece of #1, #9, #13 & seal kit

2 3/8" API reg pin 27 59.4 BG00081841 2 3/8" API reg pin 27 59.4 BG00242267

13 #24 Cubex pin 26.8 59 BG00242283 13 #24 Cubex pin 26.8 59 BG00242295

8 8

41 42
RH460hp 4" RH460 5"

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top sub 1. Top sub
1 2 3/8" API reg pin 8.2 18 BG00014822 3 1/2" API reg pin 14.8 32.56 BG00014995
2 7/8” API reg pin 8.8 19.4 BG00388091 2. Check valve dart no choke 0.45 0.99 BG00319921
2. Check valve dart no choke 0.24 0.53 BG00320005 1 3. Check valve spring 0.03 0.07 BG00014972
3. Check valve spring 0.02 0.04 BG00118911 4. Make up ring 0.20 0.44 BG00014994
4. Make up ring 0.1 0.22 BG00014825 5. Air distributor with O-ring 3.60 7.92 BG00014996

2 5. Air distributor with O-ring 2 4.4 BG00175586 6. O-ring air distributor In seal kit
6. O-ring air distributor In seal kit 7. Inner cylinder 4.2 9.24 BG00025161
7. Inner cylinder 2.1 4.62 BG00110688 2 8. Piston 14.3 31.46 BG00062889
8. Piston QLX40 7.7 16.9 BG00242889 9. Piston case with retainer ring 22 48.4 BG00014999
3
9. Piston case with retainer ring 15.4 33.9 BG00050403 10. Piston retainer ring 0.10 0.22 BG00014998
3
4 10. Piston retainer ring 0.1 0.22 BG00014819 11. O-ring guide sleeve In seal kit
11. Bit retainer ring with O-ring QLX40 0.2 0.44 BG00059039 12. Guide sleeve with O-ring 1 2.2 BG00014988
12. O-ring bit retainer ring In seal kit 4 13. Bit retainer ring with O-ring 0.4 0.88 BG00014989
13. Driver sub hard faced QLX40 2.8 6.16 BG00242001 14. O-ring bit retainer ring In seal kit
9
5 9 15. Driver sub 5 11 BG00014993
5
Optional
Air screen 0.05 0.11 BG00014743 Optional
Air screen circlip 0.01 0.02 BG00014740 Air screen 0.14 0.31 BG00014867

6 Choke set, blank, 3mm, 4.5mm and 6mm 0.02 0.04 BG00015430 Air screen circlip 0.01 0.02 BG00014862
Check valve dart with choke hole 0.24 0.53 BG00119068 Choke set, blank, 3mm, 4.5mm and 6mm 0.01 0.02 BG00015430
6
10 Check valve dart with choke hole 0.4 0.88 BG00014985
Seal Kit Driver sub hard faced 5 11 BG00162923
1 piece of #6, #12 0.02 0.04 BG00014848
11
7 Seal Kit
10 Rebuild Kit 1 piece of #6, #14 & 2 of #11 0.01 0.02 BG00015014
7 12
1 piece of #1, #9, #13 & seal kit
11 2 3/8" API reg pin 26.5 58.3 BG00242285 Rebuild Kit
11 1 piece of #1, #9, #15 & seal kit
12 3 1/2" API reg pin 41.5 91.3 BG00081790

13

14
13
8

8 15

43 44
RH460g 5" RH460hp 5"

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top sub 1. Top sub
3 1/2" API reg pin 15.5 34.1 BG00068455 1 3 1/2" API reg pin 15.5 34.1 BG00068455
#24 Cubex pin 13.5 29.7 BG00166404 2. Check valve dart no choke 0.45 0.99 BG00319921
1 2. Check valve dart no choke 0.45 0.99 BG00319921 3. Check valve spring 0.03 0.07 BG00014972
3. Check valve spring 0.03 0.07 BG00014972 4. Make up ring 0.2 0.44 BG00014994
4. Make up ring 0.20 0.44 BG00014994 5. Air distributor with O-ring 3.6 7.92 BG00093776
5. Air distributor with O-ring 3.60 7.92 BG00014996 6. O-ring air distributor In seal kit
2
2 6. O-ring air distributor In seal kit 7. Inner cylinder 4.2 9.24 BG00025161
7. Inner cylinder 4.20 9.24 BG00025161 8. Piston 14.3 31.5 BG00062889
8. Piston 14.3 31.5 BG00062889 9. Piston case with retainer ring 30 66 BG00068439

3 9. Piston case with retainer ring 30.0 66.0 BG00068439

3 10. Piston retainer ring 0.1 0.22 BG00014998
10. Piston retainer ring 0.10 0.22 BG00014998 11. O-ring guide sleeve In seal kit
4 In seal kit BG00014988
11. O-ring guide sleeve 4 12. Guide sleeve with O-ring 1 2.2
12. Guide sleeve with O-ring 1.00 2.20 BG00014988 13. Bit retainer ring with O-ring 0.4 0.88 BG00014989
9 13. Bit retainer ring with O-ring 0.40 0.88 BG00014989 14. O-ring bit retainer ring In seal kit
5
14. O-ring bit retainer ring In seal kit 15. Driver sub hard faced 5.5 12.1 BG00068435
15. Driver sub hard faced 5.50 12.1 BG00068435 5 9
Optional
Optional Air screen 0.14 0.31 BG00014867
Air screen 0.14 0.31 BG00014867 Air screen circlip 0.01 0.02 BG00014862
6 Air screen circlip 0.01 0.02 BG00014862 6 Choke set, blank, 3mm, 4.5mm and 6mm 0.01 0.02 BG00015430
10 Choke set, blank, 3mm, 4.5mm and 6mm 0.01 0.02 BG00015430 Check valve dart with choke hole 0.4 0.88 BG00014985
Check valve dart with choke hole 0.40 0.88 BG00014985

11 10 Seal Kit
Seal Kit 7 1 piece of #6, #14 & 2 of #11 0.01 0.02 BG00015014
11
7 1 piece of #6, #14 & 2 of #11 0.01 0.02 BG00015014
12
12 Rebuild Kit
Rebuild Kit 1 piece of #1, #9, #15 & seal kit
11
11 1 piece of #1, #9, #15 & seal kit 3 1/2" API reg pin 51 112 BG00081817
3 1/2" API reg pin 51.0 112 BG00081817 13
13 #24 Cubex pin 49.0 108 BG00166783
14
14

8
8 15 15

45 46
RH460 6" RH460g 6"

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top sub 1. Top sub
1 1
3 1/2" API reg pin 24 52.8 BG00014888 3 1/2" API reg pin 25.4 55.9 BG00224812

2. O-ring top sub In seal kit #28 Cubex pin 26 57.2 BG00237751

3. Check valve dart no choke 0.7 1.54 BG00321398 2. O-ring top sub In seal kit

4. Check valve spring 0.1 0.22 BG00014864 3. Check valve dart no choke 0.7 1.54 BG00321398

2 4. Check valve spring 0.03 0.07 BG00014864

5. Make up ring 0.4 0.88 BG00014865 2
5. Make up ring 0.4 0.88 BG00014865
6. Air distributor with O-ring 6.2 13.6 BG00054361
6. Air distributor with O-ring 6.2 13.6 BG00054361
3 7. O-ring air distributor In seal kit
3 7. O-ring air distributor In seal kit
8. Inner cylinder 6.4 14.1 BG00123002
8. Inner cylinder 6.4 14.1 BG00123002
9. Piston 21.4 47.1 BG00243084
9. Piston 21.4 47.1 BG00243084
4 10. Piston case with retainer ring 32.4 71.3 BG00054318
4 10. Piston case with retainer ring 46.4 102 BG00224808
11. Piston retainer ring 0.1 0.22 BG00055711
11. Piston retainer ring 0.1 0.22 BG00055711
5 12. O-ring guide sleeve In seal kit
5 10 12. O-ring guide sleeve In seal kit
13. Guide sleeve with O-ring 2.3 5.06 BG00055719
13. Guide sleeve with O-ring 2.3 5.06 BG00055719
6 14. Bit retainer ring with O-ring 0.6 1.32 BG00014871
14. Bit retainer ring with O-ring 0.6 1.32 BG00014871
10 15. O-ring bit retainer ring In seal kit 6
15. O-ring bit retainer ring In seal kit
16. Driver sub 6.5 14.3 BG00014887 16. Driver sub 7.2 15.8 BG00224798

Optional Optional
Air screen 0.1 0.22 BG00014867 Air screen 0.1 0.22 BG00014867
7 Air screen circlip 0.01 0.02 BG00014862 Air screen circlip 0.01 0.02 BG00014862
11 7
Choke set, blank, 3mm, 4.5mm and 6mm 0.01 0.02 BG00081800 11 Choke set, blank, 3mm, 4.5mm and 6mm 0.01 0.02 BG00081800

12 Check valve dart with choke hole 0.7 1.54 BG00014869 Check valve dart with choke hole 0.7 1.54 BG00014869
Driver sub hard faced 6.50 14.3 BG00242302 12
Seal Kit
8 13 13 1 Piece of #2, #7, #15 & 2 of #12 0.01 0.02 BG00014894
Seal Kit
8
1 Piece of #2, #7, #15 & 2 of #12 0.01 0.02 BG00014894
12 12 Rebuild Kit

Rebuild Kit 1 piece of #1, #10, #16 & seal kit

14 14 3 1/2" API reg pin 79 174 BG00240400
1 piece of #1, #10, #16 & seal kit
15 3 1/2" API reg pin 63.0 139 BG00240392 15 #28 Cubex pin 80 176 BG00240135

16
9 16
9

47 48
RH460 8" RH460g 8"

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top sub 1. Top sub
1 4 1/2" API reg pin 55 121 BG00096730 1 4 1/2" API reg pin 57.0 125 BG00365764
2. Check valve dart no choke 0.80 1.76 BG00321984 4 1/2 BECO pin 57.0 125 BG00278298
3. Check valve spring 0.04 0.09 BG00015376 2. Check valve dart no choke 0.80 1.76 BG00321984
4. Make up ring 0.4 0.88 BG00015380 3. Check valve spring 0.04 0.09 BG00015376
5. Air distributor with O-ring 9.4 20.7 BG00078615 4. Make up ring 0.40 0.88 BG00015380
6. O-ring air distributor In seal kit 5. Air distributor with O-ring 9.40 20.7 BG00078615
7. Inner cylinder 10.5 23.1 BG00057803 2
2 6. O-ring air distributor In seal kit
8. Piston 50 110 BG00277131 7. Inner cylinder 10.5 23.1 BG00057803
9. Piston case with retainer ring 64 141 BG00057909 8. Piston 50.0 110 BG00277131
10. Piston retainer ring 0.2 0.44 BG00096748
3 3 9. Piston case with retainer ring 94.2 207 BG00278268
11. O-ring guide sleeve In seal kit 10. Piston retainer ring 0.20 0.44 BG00096748
12. Guide sleeve with O-ring 3 6.6 BG00096749
11. O-ring guide Sleeve In seal kit
4 13. Bit retainer ring with O-ring 1.4 3.08 BG00096752
4
12. Guide sleeve with O-ring 3.00 6.60 BG00096749
14. O-ring bit retainer ring In seal kit
13. Bit retainer ring with O-ring 1.40 3.08 BG00096752
15. Driver sub 13.6 29.9 BG00096753 5
5 9 9 14. O-ring bit retainer ring In seal kit
15. Driver sub hard faced 15.9 35.0 BG00303677
Optional
Air screen 0.2 0.44 BG00303642
Optional
Air screen circlip 0.01 0.02 BG00303733
Air screen 0.20 0.44 BG00303642
6 Choke set, blank, 3mm, 4.5mm and 6mm 0.01 0.02 BG00081800 6
Air screen circlip 0.01 0.02 BG00303733
Check valve dart with choke hole 0.8 1.76 BG00015375
Choke set, blank, 3mm, 4.5mm and 6mm 0.01 0.02 BG00081800
Driver sub hard faced 13.6 29.9 BG00367978
Check valve dart with choke hole 0.80 1.76 BG00015375
10 10
Seal Kit
Seal Kit
7 11 1 piece of #6, #11 & #14 0.01 0.02 BG00303706 7 11 1 piece of #6, #11 & #14 0.01 0.02 BG00303706

Rebuild Kit
12 12 Rebuild Kit
1 piece of #1, #9, #15 & seal kit
1 piece of #1, #9, #15 & seal kit
4 1/2" API reg pin 134 295 BG00305733
4 1/2" API reg pin 168 370 BG00367721
13 13
4 1/2 BECO pin 167 367 BG00305742

14 14

8 8
15
15

49 50
RH350 10" SD Replacement parts Item description
Complete Hammer
Part No.
RH350 15” SD Replacement parts Item description
Complete Hammer
Part No.

6 5/8 API Reg Pin 32-3510-SSA/39S 7 5/8 API Reg Pin 32-3515-SSA/15S

Bit shank Bit shank

SD10 SD15

Hammer length with bit Hammer length with bit

Weight Outside diameter Hammer length Weight Outside diameter Hammer length
Bit closed Bit extended Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch kg lb mm inch mm inch mm inch mm inch

360 795 226 8,9 1480 58,3 1640 64,6 1690 66,5 1100 2420 360 14,2 1904 75 2160 85 2210 87

Air consumption, cfm Air consumption, m3/min Air consumption, cfm Air consumption, m3/min
150 psi 200 psi 250 psi 300 psi 10 bar 14 bar 17 bar 21 bar 150 psi 200 psi 250 psi 10 bar 14 bar 17 bar

690 980 1290 1610 19,5 27,8 36,5 45,6 1650 2090 2680 46,7 59,2 75,9

RH350 12” SD Replacement parts Item description

Complete Hammer
Part No.
RH350 18” SD Replacement parts Item description
Complete Hammer
Part No.

6 5/8 API Reg Pin 32-3512-SSA/39S 8 5/8 API Reg Pin 32-3518-SSA/69S

Bit shank Bit shank

SD12 SD18

Hammer length with bit Hammer length with bit

Weight Outside diameter Hammer length Weight Outside diameter Hammer length
Bit closed Bit extended Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch kg lb mm inch mm inch mm inch mm inch

618 1360 275 10,8 1729 68,1 1984 78,1 2034 80,1 1560 3430 410 16,1 2040 80,3 2290 90,3 2340 92,3

Air consumption, cfm Air consumption, m3/min Air consumption, cfm Air consumption, m3/min
150 psi 200 psi 250 psi 10 bar 14 bar 17 bar 100 psi 150 psi 200 psi 7 bar 10 bar 14 bar

880 1250 1700 19,5 35,4 48,1 1430 2120 3000 40,5 60,0 84,9

RH350 12” DHD Replacement parts Item description

Complete Hammer
Part No.
RH350 18” Numa Replacement parts Item description
Complete Hammer
Part No.

6 5/8 API Reg Pin 32-3512-SDA/39S 8 5/8 API Reg Pin 32-3518-SNA/69S

Bit shank Bit shank

DHD 112 N180

Hammer length with bit Hammer length with bit

Weight Outside diameter Hammer length Weight Outside diameter Hammer length
Bit closed Bit extended Bit closed Bit extended

kg lb mm inch mm inch mm inch mm inch kg lb mm inch mm inch mm inch mm inch

620 1365 275 10,8 1750 68,9 2004 78,9 2054 80,9 1574 3460 410 16,1 1993 78,5 2248 88,5 2298 90,5

Air consumption, cfm Air consumption, m3/min Air consumption, cfm Air consumption, m3/min
150 psi 200 psi 250 psi 10 bar 14 bar 17 bar 100 psi 150 psi 200 psi 7 bar 10 bar 14 bar

880 1250 1700 24,9 35,4 48,1 1430 2120 3000 40,5 60,0 84,9

51 52
RH350 10" SD RH350 12" SD

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top Sub 6 5/8 API Reg Pin BG00029652 1 1. Top Sub 6 5/8 API Reg Pin BG00031105
1 2. Break Out Ring BG00029666 2. Break Out Ring BG00031108
3. O-Ring, Top Sub In Seal Kit 3. O-Ring, Top Sub In Seal Kit
4. Check Valve BG00029667 4. Check Valve BG00031109
5. Choke, blank BG00047875 5. Choke, blank BG00047947
5. Choke, 1/4” BG00047876 5. Choke, 1/4" BG00047949
2
2 5. Choke, 3/8” BG00047877 5. Choke, 3/8" BG00047950
3
3 5. Choke, 1/2” BG00047878 5 5. Choke, 1/2" BG00047951
5
4 6. Check Valve Spring BG00029670 4 6. Check Valve Spring BG00054450
7. Spacer BG00029668 7. Spacer BG00031110
8. Make Up Ring BG00029669 6 8. Make Up Ring BG00031111
6 9. Rigid Valve BG00029671 9. Rigid Valve BG00031112
7
10. O-Ring, Rigid Valve In Seal Kit 10. O-Ring, Rigid Valve In Seal Kit
7 8
11. Inner Sleeve BG00029672 11. Inner Sleeve BG00031113
8
12. Piston Case BG00029673 12. Piston Case BG00054500
9
13. Piston BG00029674 13. Stop Ring BG00031114
9 12
12 14. Piston Reatiner Ring BG00029675 14. Piston BG00054499
15. O-Ring, Bit Retainer Ring In Seal Kit 15. Piston Reatiner Ring BG00031117
16. Bit Retainer Ring BG00029676 16. O-Ring, Bit Retainer Ring In Seal Kit
10
17. Driver Sub BG00029677 17. Bit Retainer Ring BG00031118
10
18. Guide Sleeve BG00031121
14 15
15 11 19. Driver Sub BG00031122
11 16
16 17
2
Seal Kit Seal Kit
13 18
1 of 3, 1 of 10, 3 of 15 BG00032790 1 piece of 3, 1 of 10, 3 of 16 BG00032791

17 2
14
13
19

53 54
RH350 12" DHD RH350 15" SD

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top Sub 6 5/8 API Reg Pin BG00031105 1. Top Sub 7 5/8 API Reg Pin BG00032389
1 2. Break Out Ring BG00031108 1 2. Break Out Ring BG00032528
3. O-Ring, Top Sub In Seal Kit 3. O-Ring, Top Sub In Seal Kit
4. Check Valve BG00031109 4. Check Valve BG00032529
5. Choke, blank BG00047947 5. Choke, blank BG00047952
5. Choke, 1/4" BG00047949 2 5. Choke, 1/4" BG00047953
2
5. Choke, 3/8" BG00047950 3 5. Choke, 3/8" BG00047954
3
5
5. Choke, 1/2" BG00047951 5 5. Choke, 1/2" BG00047957
4 6. Check Valve Spring BG00054450 4 6. Check Valve Spring BG00032533
7. Spacer BG00031110 6 7. Spacer BG00032530
8. Make Up Ring BG00031111 8. Make Up Ring BG00032531
6 7
9. Rigid Valve BG00031112 9. Rigid Valve BG00032536
7 8
10. O-Ring, Rigid Valve In Seal Kit 10 O-Ring, Rigid Valve In Seal Kit
8
11. Inner Sleeve BG00031113 11. Inner Sleeve BG00032540
12. Piston Case BG00031116 9 12. Piston Case BG00032543
9
13. Stop Ring BG00031114 13. Piston BG00032546
12 14. Piston BG00031115 12 14. Bushing BG00032547
15. Bushing BG00031403 15. Piston Reatiner Ring BG00032548
10
16. Bushing Stop Ring BG00031404 14 16. O-Ring, Bit Retainer Ring In Seal Kit
10
17. O-Ring, Bit Retainer Ring In Seal Kit 15 17. Bit Retainer Ring BG00032551
18. Bit Retainer Ring BG00031405 11 16 18. Guide Sleeve BG00032552
15
11 19. Driver Sub BG00031406 19. Driver Sub BG00032553
17
16 18
17 Seal Kit Seal Kit
13 18 1 piece of 3, 1 of 10, 3 of 17 BG00032791 13 2 1 piece of 3, 1 of 10, 3 of 16 BG00032792

14
19 19

55 56
RH350 18" SD RH350 18" Numa

Replacement parts Item description Weight Part No. Replacement parts Item description Weight Part No.
kg lb kg lb
1. Top Sub 8 5/8 API Reg Pin BG00032612 1. Top Sub 8 5/8 API Reg Pin BG00032612
1 2. Break Out Ring, Upper BG00032613 1 2. Break Out Ring BG00032613
3. O-Ring, Top Sub In Seal Kit 3. O-Ring, Top Sub In Seal Kit
4. Check Valve BG00032614 4. Check Valve BG00032614
5. Choke, blank BG00047958 5. Choke, blank BG00047958

2 5. Choke, 1/4" BG00047959 2 5. Choke, 1/4" BG00047959

5. Choke, 3/8" BG00047960 5. Choke, 3/8" BG00047960
3 3
5. Choke, 1/2" BG00047961 5. Choke, 1/2" BG00047961
5 5
6. Check Valve Spring BG00032615 6. Check Valve Spring BG00032615
4 7. Spacer BG00032616
4 7. Spacer BG00032616
8. Make Up Ring BG00032617 8. Make Up Ring BG00032617
6 6
9. Rigid Valve BG00032618 9. Rigid Valve BG00032618
7 7
10. O-Ring, Rigid Valve In Seal Kit 10. O-Ring, Rigid Valve In Seal Kit
8 11. Inner Sleeve BG00032619 8 11. Inner Sleeve BG00032619
12. Piston Case BG00032620 12. Piston Case BG00032704

9 12 13. Piston BG00032621 9 12 13. Piston BG00032705

14. Bushing BG00032622 14. Bushing BG00032706
15. Piston Reatiner Ring BG00032623 15. Piston Reatiner Ring BG00032623
16. O-Ring, Bit Retainer Ring In Seal Kit 16. O-Ring, Bit Retainer Ring In Seal Kit
14 10
10 17. Bit Retainer Ring BG00032624 14 17. Bit Retainer Ring BG00032707
18. Guide Sleeve BG00032625 18. Driver Sub BG00032708

11 15 19. Break Out Ring, Lower BG00032626 11 15

16 20. Driver Sub BG00032627 16
17 17
Seal Kit Seal Kit
18 1 piece of 3, 1 of 10, 3 of 16 BG00032793 2 1 piece of 3, 1 of 10, 3 of 16 BG00032793

19 13
13
18

20

57 58
 DRILL BITS
THAT TAKE
YOU FURTHER
Whatever conditions you’re dealing with,
Sandvik DTH drill bits make the job easier. They
are fitted with our proprietary cemented carbide
tips, which are designed to drill further.
The drill bit bodies are made from precision hardened nickel molybdenum
steel, with a compound curve shape for faster and smoother cutting and
easier removal of cuttings.

Our well-proven button bit designs are trusted by customers around

the world. The bits in the new range have an optimized head length with
maximized steel support for the cemented carbide buttons, deep face
grooves for excellent flushing and an aggressive cutting structure.

BIT SELECTION GUIDE 61

BIT SHANK IDENTIFICATION CHART 62

DRILL BITS / M SHANKS 63

DRILL BITS / DHD 340 SHANKS 67

DRILL BITS / QLX 40 SHANKS 68

DRILL BITS / QL 50 SHANKS 69

DRILL BITS / QL 60 SHANKS 70

DRILL BITS / QL 80 SHANKS 72

DRILL BITS / RH350 SHANKS 73

59 60
BIT SELECTION GUIDE BIT SHANK IDENTIFICATION CHART

Faces Carbides Rock hardness Rock structure Rock abrasiveness M 30 • 3" L = 224 mm, 8 Splines DHD 340 • 4" L = 209 mm, 8 Splines

Very hard Softer Fissured Homogeneous Very abrasive Non abrasive

Concave Ballistic

L L

M 40 • 4" L = 228 mm, 12 Splines QLX40 • 4" L = 209 mm, 12 Splines

Very hard Softer Fissured Homogeneous Very abrasive Non abrasive

Concave Spherical
L L

M 50 • 5" L = 287 mm, 12 Splines QL 50 • 5" L = 240 mm, 12 Splines

L L

Very hard Softer Fissured Homogeneous Very abrasive Non abrasive

Convex Ballistic M 60 • 6" L = 230 mm, 12 Splines QL 60 • 6" L = 253 mm, 12 Splines

L L

M 80 • 8" L = 329 mm, 12 Splines QL 80 • 8" L = 332 mm, 16 Splines

Very hard Softer Fissured Homogeneous Very abrasive Non abrasive

Convex Spherical /Ballistic

L L

SD 10 • 10” L = 412 mm, 8 Splines SD 12 • 12” L = 519 mm, 8 Splines

Very hard Softer Fissured Homogeneous Very abrasive Non abrasive

Flat Spherical
L L

DHD 112 • 12” L = 542 mm, 8 Splines SD 18 • 18” L = 674 mm, 12 Splines

L L

Cemented carbides types specifications

SD 15 • 15” L = 606 mm, 12 Splines N180 NUMA • 18” L = 603 mm, 12 Splines

This bit selection guide will help you select the right bit for the type of rock you are drilling,
Note: Cemented carbide grades DP55 and DP65 are available on several bits.

Convex face with spherical gauge buttons and ballistic front buttons.
L L

61 62
DRILL BITS / M SHANKS DRILL BITS / M SHANKS

Diameter Air Gauge Button dia. mm Weight Diameter Air Gauge Button dia. mm Weight
Sandvik RH550 Part No. Shank Sandvik RH550 Part No. Shank
holes buttons holes buttons
mm inch gauge front Kg lb mm inch gauge front Kg lb

M30 M40
Convex face / Ballistic button M30 Convex Face / Ballistic & Spherical Buttons
90 3 1/2 2 8 12 12 4,7 10 42-3A51090-R48 115 4 1/2 2 8 14 14 8,4 18 42-485B115-L55*
95 3 3/4 2 8 12 12 4,7 10 42-3A51095-R48 127 5 2 8 14 14 12 26 42-485B127-L55*
100 3 7/8 2 8 13 13 5,3 12 42-3A54100-R48

105 4 1/8 2 8 14 14 5,3 12 42-3A5B105-R48 M50

Flat face / Spherical button Concave face / Ballistic button M50
90 3 1/2 2 8 11 11 4,7 10 42-3AF0090-S48 140 5 1/2 2 8 16 14 15 33 42-5819140-R48
95 3 3/4 2 8 12 12 4,7 10 42-3AF1095-S48 140 5 1/2 2 8 16 14 15 33 42-5819140-R55
100 3 7/8 2 8 13 13 5,3 12 42-3AF4100-S48 146 5 3/4 2 8 16 14 16 35 42-5819146-R48*
105 4 1/8 2 8 14 14 5,3 12 42-3AFB105-S48 146 5 3/4 2 8 16 14 16 35 42-5819146-R55

Concave face / Spherical button

M40 130 5 1/8 2 8 16 13 13,9 31 42-5818130-S48*
Concave face / Ballistic button M40 133 5 1/4 2 8 16 13 14,3 31 42-5818133-S48*
115 4 1/2 2 8 14 14 8,4 18 42-481B115-R48 140 5 1/2 2 8 16 14 15 33 42-5819140-S48
115 4 1/2 2 8 14 14 8,4 18 42-481B115-R55 140 5 1/2 2 8 16 14 15 33 42-5819140-S65
127 5 2 8 14 14 12 26 42-481B127-R48 146 5 3/4 2 8 16 14 16 35 42-5819146-S48
127 5 2 8 14 14 12 26 42-481B127-R55* 146 5 3/4 2 8 16 14 16 35 42-5819146-S65
Concave face / Spherical button 152 6 2 8 18 16 17,1 38 42-581D152-S48
115 4 1/2 2 8 14 14 8,4 18 42-481B115-S48 165 6 1/2 2 8 18 16 18 40 42-581D165-S48
115 4 1/2 2 8 14 14 8,4 18 42-481B115-S65 Convex face / Ballistic button
121 4 3/4 2 8 14 14 11 24 42-481B121-S48 130 5 1/8 3 9 16 14 13,9 31 42-58L9130-R48*
121 4 3/4 2 8 14 14 11 24 42-481B121-S65 * 133 5 1/4 3 9 16 14 14,3 31 42-58L9133-R48*
127 5 2 8 14 14 12 26 42-481B127-S48 140 5 1/2 3 9 16 16 15 33 42-58LC140-R48
127 5 2 8 14 14 12 26 42-481B127-S65* 140 5 1/2 3 9 16 16 15 33 42-58LC140-R55
130 5 1/8 2 8 16 13 14 31 42-4818130-S48 146 5 3/4 3 9 16 16 16 35 42-58LC146-R48
133 5 1/4 2 8 16 13 15 33 42-4818133-S48* 146 5 3/4 3 9 16 16 16 35 42-58LC146-R55

Convex face / Ballistic button 152 6 3 9 18 16 17,1 38 42-58LD152-R48*

110 4 3/8 2 8 14 14 8 18 42-485B110-R48 Flat face / Spherical button
115 4 1/2 2 8 14 14 8,4 18 42-485B115-R48 130 5 1/8 2 8 16 14 13,9 31 42-58F9130-S48*
115 4 1/2 2 8 14 14 8,4 18 42-485B115-R55 133 5 1/4 3 9 16 14 14,3 31 42-58F9133-S48*
121 4 3/4 2 8 14 14 11 24 42-485B121-R48* 140 5 1/2 3 9 16 14 15 33 42-5829140-S48
127 5 2 8 14 14 12 26 42-485B127-R48 140 5 1/2 3 9 16 14 15 33 42-5829140-S65
127 5 2 8 14 14 12 26 42-485B127-R55 146 5 3/4 3 9 16 14 16 35 42-5829146-S48
130 5 1/8 3 9 16 14 14 31 42-48L9130-R48 146 5 3/4 3 9 16 14 16 35 42-5829146-S65*
133 5 1/4 3 9 16 14 15 33 42-48L9133-R48* 152 6 3 9 18 16 17,1 38 42-582D152-S48
Flat face / Spherical button Convex Face / Ballistic & Spherical Buttons
110 4 3/8 2 8 14 14 8 18 42-48FB110-S48 140 5 1/2 3 9 16 16 15 33 42-58LC140-L55*
115 4 1/2 2 8 14 14 8,4 18 42-48FB115-S48 146 5 3/4 3 9 16 16 16 35 42-58LC146-L55*
115 4 1/2 2 8 14 14 8,4 18 42-48FB115-S65*
121 4 3/4 2 8 14 14 8,4 18 42-48FB121-S48*
127 5 2 8 14 14 12 26 42-48FB127-S48
127 5 2 8 14 14 12 26 42-48FB127-S65*
130 5 1/8 2 8 16 14 14 31 42-48F9130-S48
133 5 1/4 2 8 16 14 15 33 42-48F9133-S48*

*contact you Sandvik representative for availability *contact you Sandvik representative for availability

63 64
DRILL BITS / M SHANKS DRILL BITS / M SHANKS

Diameter Air Gauge Button dia. mm Weight Diameter Air Gauge Button dia. mm Weight
Sandvik RH550 Part No. Shank Sandvik RH550 Part No. Shank
holes buttons holes buttons
mm inch gauge front Kg lb mm inch gauge front Kg lb
M60 M80
Concave Face / Ballistic Button M60 Concave face / Spherical button M80
165 6 1/2 3 9 18 18 22,9 50 42-68DE165-R48 200 7 7/8 3 9 18 18 41 90 42-88PE200-S48*
165 6 1/2 3 9 18 18 22,9 50 42-68DE165-R55* 203 8 3 9 18 18 41 90 42-88PE203-S48
172 6 3/4 3 9 18 18 25 55 42-68DE172-R48* 216 8 1/2 3 9 18 18 42 92 42-88PE216-S48
172 6 3/4 3 9 18 18 25 55 42-68DE172-R55* 219 8 5/8 3 9 18 18 42 92 42-88PE219-S48

Concave face / Spherical button 222 8 3/4 3 12 18 18 49 108 42-888E222-S48

152 6 2 8 18 18 21,8 48 42-681E152-S48 226 8 7/8 3 12 18 18 51 112 42-888E226-S48*
152 6 2 8 18 18 21,8 48 42-681E152-S65* 229 9 3 12 18 18 53 117 42-888E229-S48
155 6 1/8 2 8 18 18 22,2 49 42-681E155-S48 241 9 1/2 3 12 18 18 57 125 42-888E241-S48 *
155 6 1/8 2 8 18 18 22,2 49 42-681E155-S65 251 9 7/8 3 12 18 18 57 125 42-888E251-S48*
159 6 1/4 2 8 18 18 22,9 50 42-681E159-S48* 254 10 3 12 18 18 57 125 42-888E254-S48
159 6 1/4 2 8 18 18 22,9 50 42-681E159-S65* 270 10,625 3 12 18 18 61 134 42-888E270-S48
165 6 1/2 3 9 18 18 23,5 52 42-68DE165-S48 305 12 3 12 18 18 77 169 42-888E305-S48*
165 6 1/2 3 9 18 18 23,5 52 42-68DE165-S65 Flat Face / Spherical Button
172 6 3/4 3 9 18 18 25 55 42-68DE172-S48 203 8 3 9 18 18 41 90 42-882E203-S48*
172 6 3/4 3 9 18 18 25 55 42-68DE172-S65 216 8 1/2 3 9 18 18 42 92 42-882E216-S48*
178 7 3 9 18 18 26 57 42-68DE178-S48 222 8 3/4 3 12 18 18 49 108 42-88KE222-S48*
190 7 1/2 3 9 18 18 27 59 42-68DE190-S48

203 8 3 9 18 18 29,1 64 42-68DE203-S48

Convex face / Ballistic button

152 6 3 9 18 18 21,8 48 42-68LE152-R48*

152 6 3 9 18 18 21,8 48 42-68LE152-R55*

155 6 1/8 3 9 18 18 22,2 49 42-68LE155-R48*

155 6 1/8 3 9 18 18 22,2 49 42-68LE155-R55

159 6 1/4 3 9 18 18 22,9 50 42-68LE159-R48*

159 6 1/4 3 9 18 18 22,9 50 42-68LE159-R55*

165 6 1/2 3 9 18 18 23,5 52 42-68GE165-R48

165 6 1/2 3 9 18 18 23,5 52 42-68GE165-R55

172 6 3/4 3 9 18 18 25 55 42-68GE172-R48

172 6 3/4 3 9 18 18 25 55 42-68GE172-R55

178 7 3 9 18 18 26 57 42-68GE178-R48*

178 7 3 9 18 18 26 57 42-68GE178-R55*

Flat face / Spherical button

152 6 3 9 18 18 21,8 48 42-682D152-S48*

155 6 1/8 3 9 18 18 22,2 49 42-682D155-S48*

165 6 1/2 3 9 18 18 23,5 52 42-682E165-S48

165 6 1/2 3 9 18 18 23,5 52 42-682E165-S65

172 6 3/4 3 9 18 18 25 55 42-682E172-S48

172 6 3/4 3 9 18 18 25 55 42-682E172-S65

178 7 3 9 18 18 26 57 42-682E178-S48

190 7 1/2 3 9 18 18 27 59 42-682E190-S48*

203 8 3 9 18 18 29,1 64 42-682E203-S48

Concave Face / Ballistic & Spherical Button

165 6 1/2 3 9 18 18 23,5 52 42-68GE165-L55*

172 6 3/4 3 9 18 18 25 55 42-68GE172-L55*

*contact you Sandvik representative for availability *contact you Sandvik representative for availability

65 66
DRILL BITS / DHD 340 SHANKS DRILL BITS / QLX 40 SHANKS

Diameter Air Gauge Button dia. mm Weight Diameter Air Gauge Button dia. mm Weight
Sandvik RH460 Part No. Shank Sandvik RH460 Part No. Shank
holes buttons holes buttons
mm inch gauge front Kg lb mm inch gauge front Kg lb

DHD 340 QLX 40

Concave face / Ballistic button DHD 340 Concave Face / Ballistic Button QLX 40
115 4 1/2 2 8 14 13 8,4 18 42-361A115-R48 115 4 1/2 2 8 14 13 8,4 18 42-4G1A115-R48

115 4 1/2 2 8 14 13 8,4 18 42-361A115-R55 115 4 1/2 2 8 14 13 8,4 18 42-4G1A115-R55

127 5 2 8 14 13 12 26 42-361A127-R48 127 5 2 8 14 13 12 26 42-4G1A127-R48

127 5 2 8 14 13 12 26 42-361A127-R55 127 5 2 8 14 13 12 26 42-4G1A127-R55

Concave face / Spherical button

115 4 1/2 2 8 14 13 8,4 18 42-361A115-S48 Concave Face / Spherical Button
115 4 1/2 2 8 14 13 8,4 18 42-361A115-S65 115 4 1/2 2 8 14 13 8,4 18 42-4G1A115-S48

121 4 3/4 2 8 14 13 11 24 42-361A121-S48 115 4 1/2 2 8 14 13 8,4 18 42-4G1A115-S65

121 4 3/4 2 8 14 13 11 24 42-361A121-S65 121 4 3/4 2 8 14 13 11 24 42-4G1A121-S48*

127 5 2 8 14 13 12 26 42-361A127-S48 121 4 3/4 2 8 14 13 11 24 42-4G1A121-S65*

127 5 2 8 14 13 12 26 42-361A127-S65 127 5 2 8 14 13 12 26 42-4G1A127-S48

130 5 1/8 2 8 16 13 14 31 42-3618130-S48 130 5 1/8 2 8 16 13 14 31 42-4G18130-S48

Convex face / Ballistic button

110 4 3/8 2 8 14 13 8 18 42-365A110-R48 Convex Face / Ballistic Button
115 4 1/2 2 8 14 13 8,4 18 42-365A115-R48 110 4 3/8 2 8 14 13 8 18 42-4G5A110-R48

115 4 1/2 2 8 14 13 8,4 18 42-365A115-R55 115 4 1/2 2 8 14 13 8,4 18 42-4G5A115-R48

121 4 3/4 2 8 14 13 11 24 42-365A121-R48* 115 4 1/2 2 8 14 13 8,4 18 42-4G5A115-R55

127 5 2 8 14 13 12 26 42-365A127-R48 127 5 2 8 14 13 12 26 42-4G5A127-R48

127 5 2 8 14 13 12 26 42-365A127-R55 130 5 1/8 3 9 16 13 14 31 42-4GL8130-R48

130 5 1/8 3 9 16 13 14 31 42-36L8130-R48

Flat face / Spherical button Flat Face / Spherical Button

110 4 3/8 2 8 14 13 8 18 42-36FA110-S48 110 4 3/8 2 8 14 13 8 18 42-4GFA110-S48

115 4 1/2 2 8 14 13 8,4 18 42-36FA115-S48 115 4 1/2 2 8 14 13 8,4 18 42-4GFA115-S48

115 4 1/2 2 8 14 13 8,4 18 42-36FA115-S65 115 4 1/2 2 8 14 13 8,4 18 42-4GFA115-S65

115 4 1/2 2 8 16 13 8,4 18 42-36F8115-S65 115 4 1/2 2 8 16 13 8,4 18 42-4GF8115-S65

121 4 3/4 2 8 14 13 11 24 42-36FA121-S48* 127 5 2 8 14 13 12 26 42-4GFA127-S48

127 5 2 8 14 13 12 26 42-36FA127-S48 127 5 2 8 14 13 12 26 42-4GFA127-S65

127 5 2 8 14 13 12 26 42-36FA127-S65 130 5 1/8 2 8 16 13 14 31 42-4GF8130-S48

130 5 1/8 2 8 16 13 14 31 42-36F8130-S48 Foot valve

Foot valve 0.5 1 47-4G017
0.5 1 47-36017

*contact you Sandvik representative for availability *contact you Sandvik representative for availability

67 68
DRILL BITS / QL 50 SHANKS DRILL BITS / QL 60 SHANKS

Diameter Air Gauge Button dia. mm Weight Diameter Air Gauge Button dia. mm Weight
Sandvik RH460 Part No. Shank Sandvik RH460 Part No. Shank
holes buttons holes buttons
mm inch gauge front Kg lb mm inch gauge front kg lb

QL 50 QL 60
Concave face / Ballistic button QL 50 Concave Face / Ballistic Button QL 60
140 5 1/2 2 8 16 14 15 33 42-5019140-R48 165 6 1/2 3 9 18 18 26,9 59 42-76DE165-R48*

140 5 1/2 2 8 16 14 15 33 42-5019140-R55 165 6 1/2 3 9 18 18 26,9 59 42-76DE165-R55*

146 5 3/4 2 8 16 14 16 35 42-5019146-R48* 172 6 3/4 3 9 18 18 29 64 42-76DE172-R48*

146 5 3/4 2 8 16 14 16 35 42-5019146-R55* 172 6 3/4 3 9 18 18 29 64 42-76DE172-R55*

Concave face / Spherical button

Concave face / Spherical button 152 6 2 8 18 18 25,8 57 42-761E152-S48

130 5 1/8 2 8 16 13 13,9 31 42-5018130-S48* 152 6 2 8 18 18 25,8 57 42-761E152-S65*

133 5 1/4 2 8 16 13 14,3 31 42-5018133-S48 155 6 1/8 2 8 18 18 26,2 58 42-761E155-S48

140 5 1/2 2 8 16 14 15 33 42-5019140-S48 155 6 1/8 2 8 18 18 26,2 58 42-761E155-S65

140 5 1/2 2 8 16 14 15 33 42-5019140-S65 159 6 1/4 2 8 18 18 26,9 59 42-761E159-S48*

146 5 3/4 2 8 16 14 16 35 42-5019146-S48 159 6 1/4 2 8 18 18 26,9 59 42-761E159-S65*

146 5 3/4 2 8 16 14 16 35 42-5019146-S65 165 6 1/2 3 9 18 18 27,5 61 42-76DE165-S48

152 6 2 8 18 16 17,1 38 42-501D152-S48 165 6 1/2 3 9 18 18 27,5 61 42-76DE165-S65

Convex face / Ballistic button 172 6 3/4 3 9 18 18 29 64 42-76DE172-S48

130 5 1/8 3 9 16 14 13,9 31 42-50L9130-R48 172 6 3/4 3 9 18 18 29 64 42-76DE172-S65

133 5 1/4 3 9 16 14 14,3 31 42-50L9133-R48* 178 7 3 9 18 18 30 66 42-76DE178-S48*

140 5 1/2 3 9 16 16 15 33 42-50LC140-R48 190 7 1/2 3 9 18 18 31 68 42-76DE190-S48*

140 5 1/2 3 9 16 16 15 33 42-50LC140-R55 203 8 3 9 18 18 33,1 73 42-76DE203-S48

146 5 3/4 3 9 16 16 16 35 42-50LC146-R48 Convex face / Ballistic button

146 5 3/4 3 9 16 16 16 35 42-50LC146-R55 152 6 3 9 18 18 25,8 57 42-76LE152-R48*

152 6 3 9 18 16 17,1 38 42-50LD152-R48 152 6 3 9 18 18 25,8 57 42-76LE152-R55*

Flat face / Spherical button 155 6 1/8 3 9 18 18 26,2 58 42-76LE155-R48*

130 5 1/8 2 8 16 14 13,9 31 42-50F9130-S48 155 6 1/8 3 9 18 18 26,2 58 42-76LE155-R55*

133 5 1/4 2 8 16 14 14,3 31 42-50F9133-S48* 159 6 1/4 3 9 18 18 26,9 59 42-76LE159-R48*

140 5 1/2 3 9 16 14 15 33 42-5029140-S48 159 6 1/4 3 9 18 18 26,9 59 42-76LE159-R55*

140 5 1/2 3 9 16 14 15 33 42-5029140-S65 165 6 1/2 3 9 18 18 27,5 61 42-76GE165-R48

146 5 3/4 3 9 16 14 16 35 42-5029146-S48 165 6 1/2 3 9 18 18 27,5 61 42-76GE165-R55

146 5 3/4 3 9 16 14 16 35 42-5029146-S65 172 6 3/4 3 9 18 18 29 64 42-76GE172-R48

152 6 3 9 18 16 17,1 38 42-502D152-S48 172 6 3/4 3 9 18 18 29 64 42-76GE172-R55

Convex Face / Ballistic & Spherical Button 178 7 3 9 18 18 30 66 42-76GE178-R48*

140 5 1/2 3 9 16 16 15 33 42-50LC140-L55 178 7 3 9 18 18 30 66 42-76GE178-R55*

146 5 3/4 3 9 16 16 16 35 42-50LC146-L55 203 8 3 9 18 18 33,1 73 42-76GE203-R48*

Foot valve 203 8 3 9 18 18 33,1 73 42-76GE203-R55*

0.5 1.2 47-50017 Flat face / Spherical button

152 6 3 9 18 16 25,8 57 42-762D152-S48*

155 6 1/8 3 9 18 16 26,2 58 42-762D155-S48*

159 6 1/4 3 9 18 16 26,9 59 42-762D159-S48*

165 6 1/2 3 9 18 18 27,5 61 42-762E165-S48

165 6 1/2 3 9 18 18 27,5 61 42-762E165-S65

172 6 3/4 3 9 18 18 29 64 42-762E172-S48

172 6 3/4 3 9 18 18 29 64 42-762E172-S65

178 7 3 9 18 18 30 66 42-762E178-S48*

190 7 1/2 3 9 18 18 31 68 42-762E190-S48*

203 8 3 9 18 18 33,1 73 42-762E203-S48

*contact you Sandvik representative for availability *contact you Sandvik representative for availability

69 70
DRILL BITS / QL 60 SHANKS DRILL BITS / QL 80 SHANKS

Diameter Air Gauge Button dia. mm Weight Diameter Air Gauge Button dia. mm Weight
Sandvik RH460 Part No. Shank Sandvik RH460 Part No. Shank
holes buttons holes buttons
mm inch gauge front kg lb mm inch gauge front kg lb

QL 60 QL 80
Convex Face / Spherical & Ballistic Button QL 60 Concave face / Spherical button QL 80
165 6 1/2 3 9 18 18 27,5 61 42-76GE165-L55* 200 7 7/8 3 9 18 18 49,9 110 42-83PE200-S48*

172 6 3/4 3 9 18 18 29 64 42-76GE172-L55* 203 8 3 9 18 18 50,4 111 42-83PE203-S48

Foot valve 216 8 1/2 3 9 18 18 52,7 116 42-83PE216-S48

0.5 1.2 47-76017 219 8 5/8 3 9 18 18 53,4 117 42-83PE219-S48

222 8 3/4 3 12 18 18 54,4 120 42-838E222-S48

226 8 7/8 3 12 18 18 54,8 121 42-838E226-S48*

229 9 3 12 18 18 55,2 121 42-838E229-S48

241 9 1/2 3 12 18 18 60,8 134 42-838E241-S48*

251 9 7/8 3 12 18 18 63,5 140 42-838E251-S48*

254 10 3 12 18 18 64 141 42-838E254-S48

270 10 5/8 3 12 18 18 71,8 158 42-838E270-S48

305 12 3 12 18 18 85 187 42-838E305-S48*

Convex Face / Ballistic Button

203 8 3 9 18 18 50,4 111 42-83GE203-R55*

216 8 1/2 3 9 18 18 52,7 116 42-83GE216-R55*

222 8 3/4 3 9 18 18 54,4 120 42-83GE222-R55*

Flat Face / Spherical Button

203 8 3 9 18 18 50,4 111 42-832E203-S48*

216 8 1/2 3 9 18 18 52,7 116 42-832E216-S48*

222 8 3/4 3 12 18 18 54,4 120 42-83KE222-S48*

229 9 3 12 18 18 55,2 121 42-83KE229-S48*

Foot valve

0.5 1.2 47-83017

*contact you Sandvik representative for availability *contact you Sandvik representative for availability

71 72
DRILL BITS / RH350 SHANKS DRILL BITS / RH350 SHANKS

Diameter Air Gauge Button dia. mm Weight Diameter Air Gauge Button dia. mm Weight
Sandvik RH350 Part No. Shank Sandvik RH350 Part No. Shank
holes buttons holes buttons
mm inch gauge front kg lb mm inch gauge front kg lb

SD 10 SD 15
Concave Face / Spherical Button SD 10 Concave Face / Spherical Button SD 15
244 9 5/8 2 12 18 16 42-10JD244-SPP 444 17 1/2 4 28 20 18 42-15JV444-SPP

248 9 3/4 2 12 18 16 42-10JD248-SPP 457 18 4 36 20 18 42-15JV457-SPP

251 9 7/8 2 12 18 16 42-10JD251-SPP 483 19 4 36 20 18 42-15JV483-SPP

254 10 2 12 18 16 42-10JD254-SPP 508 20 4 36 20 18 42-15JV508-SPP

260 10 1/4 3 12 18 16 42-108D260-SPP 533 21 4 36 20 18 42-15JV533-SPP

267 10 1/2 3 12 18 16 42-108D267-SPP 559 22 4 40 20 18 42-15JV559-SPP

273 10 3/4 3 12 18 16 42-108D273-SPP 584 23 4 40 20 18 42-15JV584-SPP

279 11 3 12 18 16 42-108D279-SPP 610 24 4 40 22 20 42-15JV610-SPP

292 11 1/2 3 24 18 16 42-10JD292-SPP

302 11 8/9 3 15 18 16 42-10JD302-SPP SD 18

305 12 3 15 18 16 42-10JD305-SPP Concave Face / Spherical Button SD 18
Foot valve 444 17 1/2 4 28 20 18 42-18JV444-SPP
0.5 1.2 47-76017 508 20 4 36 20 18 42-18JV508-SPP

558 22 4 40 20 18 42-18JV558-SPP

SD 12 584 23 4 40 20 18 42-18JV584-SPP
Concave Face / Spherical Button SD 12 610 24 4 40 22 20 42-18JV609-SPP
298 11 5/6 3 24 18 16 42-12JD298-SPP 635 25 4 40 22 20 42-18JV635-SPP
304 12 3 15 18 16 42-12VD304-SPP 660 26 4 40 22 20 42-18JV660-SPP
317 12 1/2 3 15 18 16 42-12VD317-SPP 711 28 6 42 22 20 42-18JV711-SPP
323 12 5/7 3 15 18 16 42-12VD323-SPP 762 30 6 54 22 20 42-18JV762-SPP
330 13 3 15 18 16 42-12VD330-SPP 838 33 6 54 22 20 42-18JV838-SPP
343 13 1/2 3 27 18 16 42-12JD343-SPP

355 14 3 27 18 16 42-12JD355-SPP
N180 NUMA
355 14 3 27 18 16 42-12JD355-WPP Concave Face / Spherical Button N 180
381 15 3 27 20 18 42-12JV381-SPP 444 17 1/2 4 28 20 18 42-85JV444-SPP
407 19 4/7 4 28 20 18 42-12JV407-SPP 508 20 4 36 20 18 42-85JV508-SPP
444 17 1/2 4 28 20 18 42-12JV444-SPP 558 22 4 40 20 18 42-85JV558-SPP

584 23 4 40 20 18 42-85JV584-SPP

DHD 112 610 24 4 40 22 20 42-85JV609-SPP

Concave Face / Spherical Button DHD 12 635 25 4 40 22 20 42-85JV635-SPP
298 11 5/6 3 24 18 16 42-91JD298-SPP 660 26 4 40 22 20 42-85JV660-SPP
304 12 3 15 18 16 42-91VD304-SPP 711 28 6 42 22 20 42-85JV711-SPP
317 12 1/2 3 15 18 16 42-91VD317-SPP 762 30 6 54 22 20 42-85JV762-SPP
323 12 5/7 3 15 18 16 42-91VD323-SPP 838 33 6 54 22 20 42-85JV838-SPP
330 13 3 15 18 16 42-91VD330-SPP

355 14 3 27 18 16 42-91JD355-SPP

381

407
15

14
3

4
27

28
20

20
18

18
42-91JV381-SPP

42-91JV407-SPP REAMING BITS

444 17 1/2 4 28 20 18 42-91JV444-SPP

For further information, please

contact your nearest Sandvik
representative for a quote and
delivery time.

73 74
 DRILL PIPES
Our drill pipes are built for a long life. We leave
nothing to chance – welds are inspected using
ultrasound to ensure a high-strength product.
These pipes are specifically engineered to
work with our hammers. In addition, we offer
complete drill string components tailored to
your requirements, from air swivels, hammers
and bits, to complete drill rig solutions.

SANDVIK DRILL PIPES 77

SANDVIK ROTATION UNIT ADAPTERS 79

SANDVIK SUBS 80

75 76
SANDVIK DRILL PIPES SANDVIK DRILL PIPES

Length (mm)
Diameter Wall Thread for Thread for Tool joint Tool joint Weight
Length Spanner Internal
outside thickness pipe male pipe female length length Box Part no.
Tool joint length PIN (mm) Tool joint length BOX (mm) (mm) Flat Spline
(mm) (mm) (Pin) (Box) Pin (mm) (mm) kg lb

––>
102 6.3 5000 API 2 7/8" Reg API 2 7/8" Reg N N 270 270 89 196 52-102-101266

Diameter 102 6.3 5000 API 2 7/8" Reg API 2 7/8" Reg N N 350 350 98 216 52-102-10508620
outside
102 6.3 5000 API 2 7/8" Reg API 2 7/8" Reg N N 270 270 85 187 52-102-10502702
(mm)
102 6.3 6000 API 2 7/8" Reg API 2 7/8" Reg N N 270 270 94 207 52-102-101618

102 6.3 6000 API 2 7/8" Reg API 2 7/8" Reg N N 350 350 112 247 52-102-10506339
Thread for pipe Wall thickness (mm) Thread for pipe 102 6.3 7500 API 2 7/8" Reg API 2 7/8" Reg N N 350 350 136 300 52-102-103692
male (PIN) female (BOX)
102 8.8 6100 3 1/8" DIBH 3 1/8" DIBH Y Y 150 220 132 291 52-102-102935

102 8.8 9144 API 2 7/8" Reg API 2 7/8" Reg Y N 340 315 200 441 52-102-101914

102 12 6096 CUBEX #24 CUBEX #24 N N 280 280 180 397 52-CP000458

114 6.3 1196 CUBEX #28 CUBEX #28 Y Y 130 220 30 67 52-114-102298
Diameter Wall Thread for Thread for Tool joint Tool joint Weight
Length Spanner Internal 114 6.3 3000 API 3 1/2" Reg API 3 1/2" Reg Y N 140 185 60 132 52-114-101139
outside thickness pipe male pipe female length length Box Part no.
(mm) Flat Spline
(mm) (mm) (Pin) (Box) Pin (mm) (mm) kg lb 114 6.3 5000 API 3 1/2" Reg API 3 1/2" Reg N N 350 350 115 254 52-114-10508621

76 4.0 3000 API 2 3/8" Reg API 2 3/8" Reg Y N 107 165 24 53 52-076-101018 114 6.3 5000 API 3 1/2" Reg API 3 1/2" Reg N N 190 260 93 205 52-114-10504087

76 4.0 3000 API 2 3/8" Reg API 2 3/8" Reg N N 190 190 31 68 52-076-10688900 114 6.3 6000 API 3 1/2" Reg API 3 1/2" Reg N N 350 350 132 291 52-114-10505147

76 6.3 3048 API 2 3/8" Reg API 2 3/8" Reg Y N 190 260 39 86 52-076-102801 114 6.3 6000 API 3 1/2" Reg API 3 1/2" Reg N N 270 260 120 265 52-114-101238

76 6.3 4000 API 2 3/8" Reg API 2 3/8" Reg N N 190 190 46 101 52-076-10686408 114 6.3 7500 API 3 1/2" Reg API 3 1/2" Reg N N 350 350 156 344 52-114-103693

76 6.3 5000 API 2 3/8" Reg API 2 3/8" Reg N N 350 350 65 143 52-076-10508618 114 8.8 6000 API 3 1/2" Reg API 3 1/2" Reg N N 270 260 156 344 52-114-102072

76 6.3 5000 API 2 3/8" Reg API 2 3/8" Reg N N 190 190 58 128 52-076-10686990 114 8.8 7500 API 3 1/2" Reg API 3 1/2" Reg N N 350 350 201 443 52-114-103719

114 8.8 7620 API 3 1/2" Reg API 3 1/2" Reg Y N 310 300 187 412 52-114-101228

79 6.3 1524 CUBEX #21 CUBEX #21 Y Y 110 190 21 46 52-20340-111 114 8.8 9144 API 3 1/2" Reg API 3 1/2" Reg Y N 490 225 230 507 52-114-101597

79 6.3 1829 CUBEX #21 CUBEX #21 Y Y 110 190 26 56 52-20340-109 114 8.8 9144 API 3 1/2" Reg API 3 1/2" Reg Y N 310 300 222 489 52-114-101841

114 10.0 1524 CUBEX #28 CUBEX #28 Y Y 170 260 62 137 52-20830-101H

89 4.0 1800 API 2 3/8" Reg API 2 3/8" Reg Y N 107 158 20 44 52-089-101048 114 12 1219 API 3 1/2" Reg API 3 1/2" Reg Y N 490 350 58 128 52-114-102738

89 4.0 3000 API 2 3/8" Reg API 2 3/8" Reg Y N 107 158 30 66 52-089-101051 114 12 2400 API 3 1/2" Reg API 3 1/2" Reg Y N 490 350 95 209 52-114-102740

89 4.0 4000 API 2 3/8" Reg API 2 3/8" Reg N N 190 190 46 101 52-089-10686310 114 12 3000 API 3 1/2" Reg API 3 1/2" Reg Y N 490 362 116 256 52-114-102520

89 4.0 4500 API 2 3/8" Reg API 2 3/8" Reg Y N 107 158 45 99 52-089-103231 114 12 9144 API 3 1/2" Reg API 3 1/2" Reg Y N 490 225 305 672 52-114-101808

89 6.3 1500 API 2 3/8" Reg API 2 3/8" Reg Y N 107 158 24 53 52-089-101077 114 12 9144 API 3 1/2" Reg API 3 1/2" Reg Y N 490 362 310 683 52-114-102521

89 6.3 1800 API 2 3/8" Reg API 2 3/8" Reg N N 300 300 31 68 52-089-102653 114 12 9144 BECO 3" BECO 3" Y N 490 225 308 678 52-114-102919

89 6.3 1829 CUBEX #21 CUBEX #21 Y Y 110 200 28 62 52-20340-103 114 12 9144 BECO 3" BECO 3" Y N 310 300 303 668 52-114-103183

89 6.3 1829 CUBEX #24 CUBEX #24 Y Y 110 200 29 64 52-20340-105 114 12.5 7620 API 3 1/2" Reg API 3 1/2" Reg Y N 490 225 231 509 52-114-101494

89 6.3 3000 API 2 3/8" Reg API 2 3/8" Reg Y N 107 158 43 95 52-089-101079
127 6.3 1524 CUBEX #28 CUBEX #28 Y Y 170 260 47 104 52-20830-101
89 6.3 5000 API 2 3/8" Reg API 2 3/8" Reg N N 190 190 76 166 52-089-10686409
127 6.3 6000 API 3 1/2" Reg API 3 1/2" Reg N N 350 350 154 340 52-127-10505190
89 6.3 5000 API 2 3/8" Reg API 2 3/8" Reg N N 350 350 82 181 52-089-10508619
127 6.3 7500 API 3 1/2" Reg API 3 1/2" Reg N N 350 350 181 399 52-127-103694
89 6.3 6000 API 2 3/8" Reg API 2 3/8" Reg N N 350 350 95 209 52-089-10505952
127 8.8 1829 CUBEX #28 CUBEX #28 Y Y 130 220 65 143 52-20830-117
89 6.3 7500 API 2 3/8" Reg API 2 3/8" Reg N N 350 350 114 251 52-089-103691
127 8.8 6096 CUBEX #28 CUBEX #28 N N 280 280 183 403 52-127-103201
89 8.8 5000 API 2 3/8" Reg API 2 3/8" Reg N N 350 350 90 198 52-089-102955
127 8.8 7500 API 3 1/2" Reg API 3 1/2" Reg N N 350 350 228 503 52-127-103720
89 8.8 6000 API 2 3/8" Reg API 2 3/8" Reg N N 350 350 112 247 52-089-10671706
127 12 6096 API 3 1/2" Reg API 3 1/2" Reg N N 280 280 239 527 52-127-102990
89 8.8 6000 API 2 3/8" Reg API 2 3/8" Reg N N 270 270 112 247 52-089-101833
127 12 6096 BECO 3 1/2" BECO 3 1/2" N N 280 280 239 527 52-CP002185
89 12 6096 CUBEX #24 CUBEX #24 N N 280 280 150 331 52-CP001500
127 12 8077 API 3 1/2" Reg API 3 1/2" Reg Y N 315 315 310 683 52-127-102394
102 6.3 1524 CUBEX #24 CUBEX #24 Y Y 150 220 32 69 52-20830-132
127 12 9144 API 3 1/2" Reg API 3 1/2" Reg Y N 315 315 353 778 52-127-102327
102 6.3 1828 CUBEX #24 CUBEX #24 Y Y 150 220 41 90 52-102-101393

102 6.3 4000 API 2 7/8" Reg API 2 7/8" Reg N N 270 270 74 163 52-102-102778 140 8.8 7500 API 4 1/2" Reg API 4 1/2" Reg N N 350 350 257 567 52-140-103695

––>

77 78
SANDVIK ROTATION UNIT ADAPTERS SANDVIK SUBS

Diameter Diameter
outside outside
(mm) (mm)

Thread for pipe Thread for pipe Thread for Thread for pipe
female (BOX) Length, shoulder to male (PIN) pipe female Length, shoulder to male (PIN)
shoulder (mm) (BOX) shoulder (mm)

Length Thread Thread Weight Thread Length Weight

Diameter Thread Diameter Thread for
shoulder to for male for female Spanner Internal for female shoulder to Spanner Internal
outside for male Part no. outside male connection Part no.
shoulder connection connection Flats Splines connection shoulder Flats Splines
(mm) connection (Pin) kg lb (mm) (Pin) kg lb
(mm) (Pin) (Box) (Box) (mm)

76 215 M62x2 2 3/8 Reg Y N 7 14 52-076-11687703 89 API 2 3/8" Reg API 2 3/8" Reg 305 N N 13 29 52-089-111202
76 131 M62x2 2 3/8 Reg Y N 5 10 52-076-11516950
102 CUBEX #24 API 2 3/8" Reg 140 N N 9 20 52-102-112648
89 215 M62x2 2 3/8 Reg Y N 9 20 52-089-11512674 102 API 2 7/8" Reg API 2 3/8" Reg 130 Y N 7 15 52-102-111029
89 300 M80x3 2 3/8 Reg Y N 13 28 52-089-11516555
89 89 M62x2 2 3/8 Reg Y N 6 13 52-089-11687217 114 CUBEX #24 API 3 1/2" Reg 160 Y N 10 22 52-114-112649
114 CUBEX #24 API 3 1/2" Reg 160 Y Y 9 20 52-114-112269
102 300 M80x3 2 7/8 Reg Y N 17 37 52-102-11517523 114 CUBEX #28 API 3 1/2" Reg 160 Y Y 11 24 52-114-111059
102 215 M62x2 2 7/8 Reg Y N 13 28 52-102-11502994 114 API 2 3/8" Reg API 3 1/2" Reg 160 Y N 9 19 52-114-111053
114 API 2 7/8" Reg API 3 1/2" Reg 160 Y N 9 20 52-114-111056
114 300 M80x3 3 1/2 Reg Y N 19 42 52-114-11505151 114 API 3 1/2" Reg API 2 3/8" Reg 120 Y N 9 20 52-114-111031
114 215 M62x2 3 1/2 Reg Y N 13 29 52-114-11503612 114 API 3 1/2" Reg API 2 3/8" Reg 223 Y N 10 22 52-114-11518177
114 307 3 1/2 Reg 2 3/8 Reg Y N 14 30 52-114-11518907 114 API 3 1/2" Reg API 2 7/8" Reg 150 Y N 11 24 52-114-111039
114 307 3 1/2 Reg 3 1/2 Reg Y N 21 47 52-114-11518332 114 API 3 1/2" Reg API 3 1/2" Reg 160 Y N 11 23 52-114-111061
114 307 3 1/2 Reg 3 1/2 Reg Y N 26 56 52-114-11518871 114 API 3 1/2" Reg API 3 1/2" Reg 228 Y N 15 33 52-114-111352
114 API 3 1/2" Reg API 3 1/2" Reg 230 Y N 14 32 52-114-112668
127 307 3 1/2 Reg 3 1/2 Reg Y N 27 60 52-127-11518872 114 API 3 1/2" Reg API 3 1/2" Reg 305 N N 21 46 52-114-111578
127 300 M80x3 3 1/2 Reg Y N 24 53 52-127-11516261 114 API 3 1/2" Reg API 3 1/2" Reg 500 Y N 32 70 52-114-112537
114 DIBH 3 1/8" API 3 1/2" Reg 260 Y N 17 36 52-114-112700
114 BECO 3" API 3 1/2" Reg 160 Y N 10 22 52-114-112637

127 CUBEX #28 API 3 1/2" Reg 132 Y Y 11 23 52-127-111060

127 BECO 3 1/2" API 3 1/2" Reg 228 Y N 20 44 52-127-111897
127 BECO 3 1/2" API 3 1/2" Reg 228 Y N 20 44 52-127-111943
127 BECO 3 1/2" API 3 1/2" Reg 410 Y N 36 79 52-127-112572
127 BECO 3 1/2" API 3 1/2" Reg 609 Y N 55 121 52-127-111524
127 API 3 1/2" Reg BECO 3" 228 Y N 19 41 52-127-112543
127 DIBH 3 1/8" API 3 1/2" Reg 260 Y N 21 46 52-127-11-2675
127 DIBH 3 1/8" DIBH 3 1/8" 260 Y N 15 32 52-127-112674

140 BECO 3 1/2" API 4 1/2" Reg 228 Y N 21 46 52-140-111948

146 API 4 1/2" Reg API 3 1/2" Reg 132 Y N 17 36 52-146-111067

150 API 4" IF API 3 1/2" Reg 280 N N 37 82 52-150-112621

164 API 3 1/2" Reg BECO 3 1/2" 311 Y N 33 73 52-164-112616

164 API 4 1/2" Reg CUBEX #24 310 Y N 24 53 52-164-112592
164 API 4 1/2" Reg CUBEX #28 310 Y N 26 57 52-164-112667

171 API 5 1/2" Reg API 3 1/2" Reg 406 Y N 42 93 52-171-112396

171 API 5 1/2" Reg API 3 1/2" Reg 406 Y N 43 95 52-171-112065
171 API 5 1/2" Reg API 3 1/2" Reg 406 Y N 45 99 52-171-112402

79 80
 ACCESSORIES
FOR INCREASED
SAFETY AND
PRODUCTIVITY
We’ve developed a wide range of accessories
that make it easier and safer to work with
hammers. They include hammer lifting bails, foot
valve assembly and disassembly tools and a
comprehensive hammer service kit.

SANDVIK TUBEX SYSTEMS 83

ACCESSORIES 85

PART NO. KEYS 86

81 82
SANDVIK TUBEX SYSTEMS SANDVIK TUBEX SYSTEMS

Tubex XL-140
Part Description Weight (kg) Weight (lb) Part no.
Guide device QL50 (Foot valve, 47-55017) 21 46,3 80-5500-140D
Guide device DHD350 (Foot valve, 47-69037) 21 46,3 80-6900-140D
Pilot bit 2/8, 14/14, CV, DP65 11 24,2 81-140A-140A65
Hammer Guide sleeve Steel casing Drill pipe
Eccentric reamer 4 8,8 82-140A-189W65
Casing shoe 2,4 5,3 84-140D-00
Locking kit 0,5 1 85-140A-KT
Pilot bit Reamer Casing Guide
shoe device
Tubex XL-165
Guide device M60 34 75 80-6800-165D
Locking kit
Guide device DHD360 (Foot valve, 47-73017-1) 34 75 80-7300-165D
Guide device QL60 (Foot valve,47-76017) 34 75 80-7600-165D
Pilot bit 2/8, 16/16, CV, DP65 17 37,5 81-165A-165A65
Eccentric reamer 7 15,4 82-165A-212W65

Tubex product range Casing shoe 3,2 7 84-165D-00

Locking kit 0,5 1 85-165A-KT
Tubex type Casing, recom. size (mm) Min. wall thickness Max. drill bit diameter Reaming diameter
Max. OD Min. ID
(mm) (mm) A (mm) Tubex XL-180
Guide device DHD360 (Foot valve, 47-73017-1) 44 97 80-7300-180D
90 115 102 5 90 123
Pilot bit 2/8, 16/16, CV, DP65 24 53 81-180A-180A65
115 142 128 5 115 152
Eccentric reamer 10 22 82-180A-232W65
140 171 157 5 140 187
Casing shoe 4 8,8 84-180D-00
165 196 183 5,5 165 212
Locking kit 0,5 1 85-180A-KT
180 219 194 6,3 180 232
Tubex XL-190
190 222 205 6,3 190 237
Guide device M60 40 88 80-6800-190D
240 273 260 6,3 240 306
Guide device QL60 (Foot valve, 47-76017) 44 97 80-7600-190D
280 327 305 7,1 280 370
Guide device DHD360 (Foot valve, 47-73017-1) 44 97 80-7300-190D
Pilot bit 3/8, 16/16, CV, DP65 29 64 81-190A-190A65
Tubex XL-90 Eccentric reamer 10 22 82-190A-237W65
Part Description Weight (kg) Weight (lb) Part no. Casing shoe 4 8,8 84-190D-00
Guide device M30 7 15,4 80-3A00-090D Locking kit 0,5 1,0 85-190A-KT
Guide device DHD3,5 (Foot valve, 47-24017) 7 15,4 80-2400-090D Tubex XL-240
Pilot bit 1/8, 12/12, CV, DP65 3,6 7,9 81-090B-090A65 Guide device M80 67 148 80-8800-240D
Eccentric reamer 1,4 3 82-090B-123W65 Guide device DHD 380 (Foot valve, 47-87017) 67 148 80-8700-240D
Casing shoe 1,1 2,4 84-090D-00 Pilot bit 2/12, 16/16, CV, DP65 46 101 81-240B-240A65
Locking kit 0,5 1 85-090A-KT Eccentric reamer 18 40 82-240B-308W65
Tubex XL-115 Casing shoe 7 15,4 84-240A-00
Guide device M40 12 26,4 80-4800-115D Locking kit 1 2,2 85-240A-KT
Guide device DHD340 (Foot valve, 47-36017) 12 26,4 80-3600-115D Tubex XL-280
Guide device QLX40 (Foot valve, 47-4G017) 12 26,4 80-4G00-115D Guide device SD10 (Foot valve, 47-10017) 160 353 80-1000-280A
Pilot bit 2/8, 14/14, CV, DP65 8 17,6 81-115A-115A65 Pilot bit 3/12, 18/18, CV, DP65 88 194 81-280A-280A65
Eccentric reamer 2,6 5,7 82-115A-152W65 Eccentric reamer 43 94 82-280A-378W65
Casing shoe 1,6 3,5 84-115D-00 Casing shoe 15 33 84-280A-00
Locking kit 0,5 1 85-115A-KT Locking kit 1,5 3,3 85-280A-KT

83 84
ACCESSORIES PART NO. KEYS

Weight Hammers
Description Part No.
kg lb
Hammer lifting bail Hammer code 32 - 55 65 - R M A / 04 C
2-3/8" Reg box 3600 kg 5.1 11.2 BG00016425
Hammer
2-7/8" Reg box 3600 kg 8 17.6 BG00016426 family Hammer External
Hammer lifting bail 55 = RH550 diameter Application modifiers
3-1/2" Reg box 3600 kg 14 30.8 BG00016427
46 = RH460 30 = 3" modifier Hammer Top sub connection S Standard
3-1/2" IF box 3600 kg 10 22 BG00016428 35 = RH350 35 = 3.5" R Reversible shank For Internal 04 = 3 ½ API REG PIN Retract carbides
C
40 = 4" G HD (Large OD) M Mission use in top sub
4-1/2" Reg box 3600 kg 19 41.8 BG00016429 11 = 2 ⅞ API REG PIN
50 = 5" W Deep hole Q QL 16 = 2 ⅜ API REG PIN
CUBEX #24 box 3600 kg 13 28.6 BG00294441 55 = 5" HD H Horizontal D DHD 19 = 4 ½ API REG PIN
60 = 6" S Standard T QLX 39 = 6 ⅝ API REG PIN
CUBEX #21 box 3600 kg 13 28.6 BG00294442
65 = 6" HD expanded N NUMA 25 = 3 ½ API REG BOX
E
CUBEX #28 box 3600 kg 13 28.6 BG00294450 70 = 7" HD pressure range 74 = 3 ½ API IF PIN
80 = 8" 55 = 3 ½ BECO PIN
4 1/2" BECO box 3600 kg 25 55 BG00294443
85 = 8" HD 69 = 8 5/8 API REG PIN
10 = 10" 72 = 4 ½ BECO PIN
12 = 12" 77 = #24 CUBEX PIN
Hammer service kit Hammer service kit 15 = 15" 63 = #21 CUBEX PIN
4" 2 4.4 BG00303552 18 = 18" 56 = #28 CUBEX PIN
84 = 5 1/4" BECO PIN
5" 4.5 9.9 BG00274811

6" 5.4 11.9 BG00275989

8" 11.5 25.3 BG00324800

Foot valve assembly tool

QLX40 0.3 0.7 62-4G017A

Drill bits
Foot valve DHD3.5 0.2 0.4 62-24017A
assembly tool DHD340 0.3 0.7 62-36017A
Bit code 42 - 68 G E 165 - R 55 H
QL50 0.4 0.8 62-55017A Shank code
QL60 0.4 0.8 62-76017A 3A = M 30 Face design
3H = DHD 3.5 HD Options
Concave face Button
QL80 0.6 1.3 62-83017A 4G = QLX40 combination Bit diameter in Carbide grade H = Extra hard body
Face Flushing Gauge millimeters 48 = XT48 F = Rope fishing thread
48 = M 40 0 = 11 / 11
code holes buttons
58 = M 50 1 = 12 / 12 55 = DP55
1 2 8 Button style 65 = DP65
Foot valve disassembly tool 68 = M 60 2 = 13 / 11
88 = M 80 D 3 9 With wear D2 = Diamond
Foot valve DHD3.5 / DHD340 1.8 3.9 63-010KTA
3 = 13 / 12 Shape Std
24 = DHD 3.5 T 2 10 protection
disassembly tool 4 = 13 / 13
36 = DHD 340 8 3 12 Spherical S W
QLX4 / QL5 / DHD350 2.5 5.5 63-020KTA 5 = 14 / 11
69 = DHD 350 P,J 3 varies
6 = 14 / 12 Ballistic R U
QL6 / DHD 360 3.2 7 63-030KTA Flat face
73 = DHD 360 7 = 16 / 12
87 = DHD 380 Face Flushing Gauge 8 = 16 / 13 Spherical
QL8 / DHD380 4.9 10.9 63-040KTA
50 = QL 50 code holes buttons gauge L T
9 = 16 / 14
Ballistical face
76 = QL 60 A 2 10 A = 14 / 13
83 = QL 80 F 2 8 B = 14 / 14
2 3 9 C = 16 / 16
K 3 12 D = 18 / 16
Convex face E = 18 / 18
F = 18 / 14
Face Flushing Gauge
code holes buttons G = 12 / 11
3 2 7
5 2 8
6 2 10
C 3 12
L 3 9
G 3 9

85 86
87