D ATA S H E E T

W24-2Exi
Photoelectric sensors for explosive atmospheres

Safe and reliable switching in Ex-areas (gas)

The W24-2Exi Series has been devel- • the WL24-2Exi photoelectric reflex
oped for applications in explosive sensor has a maximum scanning
areas, in order to provide intrinsic range up to 22 m/PL80A,
safety according to EN 60079-0 • the WLL24-2Exi fibre-optic cable
(2009), EN 60079-11 (2007) and version which, depending on the
EN 60079-28 (2007), and EC type type of optical head, can be used
examined by the “Physikalisch- in both through-beam and proxim-
Technische Bundesanstalt (PTB)” ity mode whereby the maximum
distance to the object is 1,000 mm
in Braunschweig, Germany. The
and 40 mm respectively.
switching outputs of the devices are
designed according to EN 60947-5-6
(NAMUR). The sturdy zinc die-cast housings with
enclosure rating IP 67 (IP 65 with
Therefore, the W24-2Exi Series
WLL24), the cable glands and plugs
labelled II 2G Ex ia op is IIC T4
that can be rotated towards the bot-
complies with the requirements of
tom and rear of the sensor, and very
Category 2G according to the new
good insensitivity to ambient light
Directive 94/9/EC (ATEX) and may be
make all of these devices ideally suit-
used in the explosive areas “Zone 1
ed for use in industrial environments.
(gas)” and “Zone 2 (gas)”.
The device variants used depend on
the specific application:
• the WT24-2Exi photoelectric
proximity sensor with an adjust-
able scanning distance of 100 ...
2,000 mm and background sup-
pression,
 WT24-2Exi Photoelectric proximity sensors, BGS, infrared – DC

Dimensional drawing
Scanning distance
40 … 2,000 mm

14
Photoelectric proximity sensors

7 14 17.5

6.5
Marking:
1
II 2G Ex ia op is IIC T4 according
2
to Directive 94/9/EG (ATEX)
3 4
According to category 2G

87.5
Switching output: 5

15
61
EN 60947-5-6 (NAMUR) 6
M5

4.7
8

26
Background suppression

max. 32
can be set very precisely 9

Infrared light 30 11.8

27 65

Adjustments 1 Alignment sight

2 LED signal strength indicator
2 3 Standard direction of the material being scanned
4 Middle of optic axis, sender
5 Middle of optic axis, receiver at close range
6 Middle of optic axis, receiver at long range
10 7 M5 threaded mounting hole, 6 mm deep
8 M5 threaded mounting hole
9 M16 screw fixing or M12 plug, rotatable by 90°
10 Adjustment of scanning distance: Potentiometer

Connection types
WT24-2X200 WT24-2X400

Accessories M16, terminals 4-pin, M12

Mounting systems
+8,2 V 1
Plug 4-pin, M12 1 +8.2 V
Switching amplifier 0V 2
2 0V
3
3 0V
4
4 NC

2 SICK 2010-06-01
Subject to change without notice
 W24-2Exi

Technical data WT24-2 X200 X400

Scanning distance, typ. max. 40 ... 2,000 mm 1)

Operating distance 100 ... 2,000 mm 1)
Adjustment of operating distance Potentiometer
Light source 2), light type LED, infrared light
Light spot diameter Approx. 50 mm at 2,000 mm
Supply voltage VS 3) 5 … 15.5 V DC
Residual ripple 4) 0.4 VPP
EC-type examination certificate PTB 03 ATEX 2105
Input voltage Ui max. 5) 15.5 V
Input current Ii max. 5) 53 mA
Input power Pi max. 5) 100 mW
Internal capacity Ci max. 5) 80 nF
Internal inductivity Li max. 5) ≈ 0 μH (negligible small)
Switching output/current consumption Control current dependent on switching 6)
Object is detected ≥ 2,2 mA
Object is not detected ≤ 1 mA
Switching mode Light-switching
Response time 7) ≤ 10 ms
Max. switching frequency 8) 50 Hz
Connection types M16, terminal connection
Plug 4-pin, M12
Protection class 9)
Circuit protection 10) A, C
Enclosure rating IP 67
Ambient temperature TA Operation: –20 °C … +60 °C
Storage: –25 °C ... +70 °C
Weight Approx. 330 g
Housing material Zinc die-cast housing
1) 3) 5) 9)
Object with 90 % remission (based on Limit values, Supply with switching For connection to a separately certified Reference voltage DC 50 V
10)
standard white to DIN 5033) amplifier EN2Ex (Ri approx. 1 kΩ) intrinsically safe circuit only A = VS-connections reverse-polarity
2) 4) 6)
Average service life 100,000 h at May not exceed or fall short of According to EN 60947-5-6 (NAMUR) protected
7)
TA = +25 °C VS tolerances Signal transit time with resistive load C = Interference pulse suppression
8)
With light/dark ratio 1:1
Scanning distance Lower bound of detection Ordering information
Model name Part No.
250 WT24-2X200 1041910
1 *) 900
WT24-2X400 1040722
2 *) 1,300

3 *) 2,000 200
1
0 (mm) 500 1,000 1,500 2,000
*) Lower bound of detection area depending on the 150
Lower bound of detection/mm

adjusted scanning distance

1 Scanning distance on black, 6 % remission

100
2 Scanning distance on grey, 18 % remission
3 Scanning distance on white, 90 % remission
20 50

6%/90%
0
15 500 1000 1500 2000
adjusted scanning distance
18%/90%

10
% of scanning distance

5 90%/90%

0
500 1000 1500 2000
2010-06-01 SICK 3
Subject to change without notice
 izk:i&1

Professional Examination Board

ोफेशनल ए जा मनेशन बोड

Predefined Template

फोटो / Photo ह ता र / Signature

4” x 5” सेमी फोटो यहाँ

चपकाये
Box-2
नदश / Instruction)ह ता र / Signature)
4” x 5” cm photo
paste here
 (i)अपना पूरा ह ता र बॉ स-2 के अंदर कर, (ii) अँ ेजी के कै पटल
अ र esa vFkok vaxzsth ds y/kq gLrk{kj ekU; ugha gksaxs A (iii) एक से
अ धक ह ता र मा य नह ं ह गे
 (i) Do your full signature within box-2, (ii)signature in capital letter
Box-1
or Short is not allowed(iii) more than 1 signature will be invalid
नदश / Instruction(फोटो / Photo)
फोटो ाफके नचले ह से पर फोटो खचवाने क दनांक व आवेदक का नाम प ट होना चा हएतथा यह आवेदन करने क
त थ से तीन माह से अ धक पुराना नह ं होना चा हए
 Photograph of the candidate should bear his/ her name and the date on the front of the lower part of
photographandit should not old more than 3 months from application date

व-घोषणा / Self-declaration:

म घोषणा करता हूँ क मेरे वाराआवेदन म द गई सम त जानकार पण

ू तः स य है ।य द मेरे वारा द गई
जानकार कसी भी तर परझूठ या पा ता मापदं डक आव यकताओं अनुसारसंतोषजनकनह ंपाई जाती है तो मेर
उ मीदवार र क जा सकती ह।

अथवा / Or

I hereby declare that all statements made in this application are true to the best of my knowledge and
belief. If any information being found false at any stage or not satisfying the eligibility criteria

व-घोषणा / Self-declaration

(ऊपर दए गए घोषणा कोबॉ स-3 के अंदरअपने लेखन म कॉपी कर/ Copy in your
running hand writingin box-3, the declaration given above)

ोफे शनल ए जािमनेशन बोड, भोपाल समुह-3 भत पर ा-2022 Page 89

Box-3
 WL24-2Exi Photoelectric reflex sensors, red light – DC

Dimensional drawing
Scanning range
0 … 22 m

14
Photoelectric reflex sensors

5 14 17.5

6.5
Marking: 10
1
II 2G Ex ia op is IIC T4 according
2
to Directive 94/9/EG (ATEX)
According to category 2G

87.5
3

14
Switching output: 4
EN 60947-5-6 (NAMUR) M5

37

4.7
6
Red light

max. 32
Device plug can be rotated 7
30 11.8
through 90°
27 65

Adjustments 1 Alignment sight

2 LED signal strength indicator
2 3 Middle of optix axis, sender
4 Middle of optic axis, receiver
5 M5 threaded mounting hole, 6 mm deep
6 M5 threaded mounting hole
8 7 M16 screw fixing or M12 plug, rotatable by 90°
8 Sensitivity adjustment: Potentiometer

Connection types
WL24-2X230 WL24-2X430

Accessories M16, terminals 4-pin, M12

Mounting systems
+8,2 V 1
Reflectors 1 +8.2 V
Plug 4-pin, M12 0V 2
2 0V
Switching amplifier 3
3 0V
4
4 NC

4 SICK 2010-06-01
Subject to change without notice
 W24-2Exi

Technical data WL24-2 X230 X430

Scanning range typ. max. 0 ... 22 m

Scanning range, recommended 0 … 15 m
Relating to Reflector PL80A
Sensivity adjustment Potentiometer
Light source 1), light type LED, red light
Light spot diameter 250 mm at 15 m
Supply voltage VS 2) 5 … 15.5 V DC
Residual ripple 3) 0.4 VPP
EC-type examination certificate PTB 08 ATEX 2029
Input voltage Ui max. 4) 15.5 V
Input current Ii max. 4) 53 mA
Input power Pi max. 4) 100 mW
Internal capacity Ci max. 4) 80 nF
Internal inductivity Li max. 4) ≈ 0 μH (negligible small)
Switching output/current consumption Control current dependent on switching 5)
Light beam not interrupted ≥ 2.2 mA
Light beam interrupted ≤ 1 mA
Switching mode Light-switching
Response time 6) ≤ 10 ms
Max. switching frequency 7) 50 Hz
Connection types M16, terminal connection
Plug 4-pin, M12
Protection class 8)
Circuit protection 9) A, C
Enclosure rating IP 67
Ambient temperature TA Operation: –20 °C … +60 °C
Storage: –25 °C ... +70 °C
Weight Approx. 330 g
Housing material Zinc die-cast housing
1) 3) 6)
Average service life 100,000 h at May not exceed or fall short of Signal transit time with resistive load
7)
TA = +25 °C VS tolerances With light/dark ratio 1:1
2) 4) 8)
Limit values, Supply with switching am- For connection to a separately certified Reference voltage 50 V DC
9)
plifier EN2Ex (Ri approx. 1 kΩ) intrinsically safe circuit only A = VS-connections reverse-polarity
5)
According to EN 60947-5-6 (NAMUR) protected
C = Interference pulse suppression

Scanning range and operating reserve Ordering information

100
Model name Part No.
1 0.03 15 22 WL24-2X230 1026036
16 WL24-2X430 1026037
2 0.03 11

3 0.03 11 16 1

4 0.03 9 13

5 0.03 7 10 2 3
10
6 0.3 6 10 4
7 0.15 10 14 20
5
Operating reserve

Operating range
0 (m) 4 8 12 16 20 24

Operating range Typ. max. scanning range

Scanning range
max. typical
1
Reflector type Operating range (m) 4 8 12 16 20 24
1 P L80A 0.03 ... 15 m
2 PL50A 0.03 ... 11 m
3 PL40A 0.03 ... 11 m
4 PL30A 0.03 ... 9 m
5 PL20A 0.03 ... 7 m
6 Diamond Grade (20 cm x 20 cm) 0.3 ... 6 m
7 C110 0.15 ... 14 m

2010-06-01 SICK 5
Subject to change without notice
 WLL24-2Exi Photoelectric sensors with fibre-optic cable, red light – DC

Dimensional drawing
Scanning distance
0 … 40 mm

14
Scanning range
0 … 1,000 mm 10 5 14 18

7
1
Photoelectric sensors with fibre-optic cable
2
Marking:
II 2G Ex ia op is IIC T4 according 3

87.5
14
to Directive 94/9/EG (ATEX) 4

37.5
EN 60947-5-6 (NAMUR) M5

4.7
6
Red light

max. 32
Fibre-optic cable, exchangeable 7 30 11.8

27 65

74.7

Adjustments 1 Alignment sight

2 LED signal strength indicator
2 3 Middle of optic axis, sender
4 Middle of optic axis, receiver
5 M5 threaded mounting hole, 6 mm deep
6 M5 threaded mounting hole
8 7 M16 screw fixing or plug M12, 4-pin,
rotatable by 90°
8 Sensitivity adjustment: Potentiometer

Connection types
WLL24-2X230 WLL24-2X430

Accessories M16, terminals 4-pin, M12

Mounting systems
+8,2 V 1
Reflectors 1 +8.2 V
Plug 4-pin, M12 0V 2
2 0V
Switching amplifier 3
3 0V
4
4 NC

6 SICK 2010-06-01
Subject to change without notice
 W24-2Exi

Technical data WLL24-2 X230 X430

Scanning distance typ. max. 0 ... 40 mm 1)

Scanning distance 0 ... 25 mm 2)
Scanning distance 0 ... 10 mm 3)
Fibre-optic cable (proximity system) LL3-DB01
Adjustment of operating distance Potentiometer
Scanning range typ. max. 0 … 1,000 mm
Fibre-optic cable (Through-beam system) LL3-TB02 and tip adapter LL3-TA01
Scanning range, recommended 0 … 100 mm
Fibre-optic cable (Through-beam system) LL3-TB02
Sensivity adjustment Potentiometer
Light source 4), light type LED, red light
Supply voltage VS 5) 5 … 15.5 V DC
Residual ripple 6) 0.4 VPP
EC-type examination certificate PTB 08 ATEX 2029
Input voltage Ui max. 7) 15.5 V
Input current Ii max. 7) 53 mA
Input power Pi max. 7) 100 mW
Internal capacity Ci max. 7) 80 nF
Internal inductivity Li max. 7) ≈ 0 μH (negligible small)
Switching outputs/current consumption Control current dependent on switching 8)
Light beam not interrupted ≥ 2.2 mA
Light beam interrupted ≤ 1 mA
Switching mode Light-switching
Response time 9) ≤ 10 ms
Max. switching frequency 10) 50 Hz
Connection types M16, terminal connection
Plug 4-pin, M12
Protection class 11)
Circuit protection 12) A, C
Enclosure rating IP 65
Ambient temperature TA Operation: –20 °C … +60 °C
Storage: –25 °C ... +70 °C
Weight Approx. 330 g
Housing material Zinc die-cast housing
1) 5) 8) 12)
Object with 90 % remission (based on Limit values, Supply with switching According to EN 60947-5-6 (NAMUR) A = VS-connections reverse-polarity
9)
standard white to DIN 5033) amplifier EN2Ex (Ri approx. 1 kΩ) Signal transit time with resistive load protected
2) Object with 18 % remission, gray 6) May not exceed or fall short of 10) With light/dark ratio 1:1 C = Interference pulse suppression
3) 11)
Object with 6 % remission, black VS tolerances Reference voltage 50 V DC
4) 7)
Average service life 100,000 h at For connection to a separately certified
TA = +25 °C intrinsically safe circuit only

Ordering information
Model name Part No.
WLL24-2X230 1026038
WLL24-2X430 1026039

2010-06-01 SICK 7
Subject to change without notice
 Australia Österreich
2010-06-01 ∙ GO/GO (2010-06) ∙ A4 4c int35

Phone +61 3 9497 4100 Phone +43 (0)22 36 62 28 8-0

1800 33 48 02 – tollfree E-Mail [email protected]
E-Mail [email protected] Polska
Belgium/Luxembourg Phone +48 22 837 40 50
Phone +32 (0)2 466 55 66 E-Mail [email protected]
E-Mail [email protected] Republic of Korea
Brasil Phone +82-2 786 6321/4
Phone +55 11 3215-4900 E-Mail [email protected]
E-Mail [email protected] Republika Slovenija
Ceská Republika Phone +386 (0)1-47 69 990
Phone +420 2 57 91 18 50 E-Mail [email protected]
E-Mail [email protected] România
China Phone +40 356 171 120
Phone +852-2763 6966 E-Mail [email protected]
E-Mail [email protected] Russia
Danmark Phone +7 495 775 05 34
Phone +45 45 82 64 00 E-Mail [email protected]
E-Mail [email protected] Schweiz
Deutschland Phone +41 41 619 29 39
Phone +49 211 5301-301 E-Mail [email protected]
E-Mail [email protected] Singapore
España Phone +65 6744 3732
Phone +34 93 480 31 00 E-Mail [email protected]
E-Mail [email protected] Suomi
France Phone +358-9-25 15 800
Phone +33 1 64 62 35 00 E-Mail [email protected]
E-Mail [email protected] Sverige
Great Britain Phone +46 10 110 10 00
Phone +44 (0)1727 831121 E-Mail [email protected]
E-Mail [email protected] Taiwan
India Phone +886 2 2375-6288
Phone +91–22–4033 8333 E-Mail [email protected]
E-Mail [email protected] Türkiye
Israel Phone +90 216 587 74 00
Phone +972-4-999-0590 E-Mail [email protected]
E-Mail [email protected] United Arab Emirates
Italia Phone +971 4 8865 878
Phone +39 02 27 43 41 E-Mail [email protected]
E-Mail [email protected] USA/Canada/México
Japan Phone +1(952) 941-6780
Phone +81 (0)3 3358 1341 1 800-325-7425 – tollfree
E-Mail [email protected] E-Mail [email protected]
Nederlands
Phone +31 (0)30 229 25 44
E-Mail [email protected]
Norge More representatives and agencies
Phone +47 67 81 50 00 in all major industrial nations at
E-Mail [email protected] www.sick.com

SICK AG | Waldkirch | Germany | www.sick.com