HYDRAULIC MOTORS EPMT

APPLICATION
» Conveyors;
» Metal working machines;
» Machines for agriculture;
» Road building machines;
» Mining machinery;
» Food industries;
» Special vehicles;
» Plastic and rubber machinery etc.

CONTENTS OPTIONS
Specification data ......................................... 87 » Model- Disc valve, geroler;
Function diagrams ................................. 88÷90 » Flange with wheel mount;
Dimensions and mounting ............................ 91 » Short motor;
Shaft extensions ............................................ 92
» Tacho connection;
Dimensions and mounting- EPMTS, V ...... 93÷94
» Side and rear ports
Internal Spline data ....................................... 95
» Shafts- straight, splined and tapered;
Permissible shaft loads .................................. 95
» Metric and BSPP ports;
Tacho connection .......................................... 96
Order code .................................................. 96 » Other special features.

GENERAL
3
Displacement, [cm /rev.] 161,1÷725
Max. Speed, [RPM] 625÷175
Max. Torque, [daNm] 47÷125
Max. Output, [kW] 20,2÷33,5
Max. Pressure Drop, [bar] 200÷115
Max. Oil Flow, [l/min] 100÷125
Min. Speed, [RPM] 10÷5
Permissible Shaft Loads, [daN] Prad=1700; Pa=1000
Pressure fluid Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
O
Temperature range, [ C] -30÷90
2
Optimal Viscosity range, [mm /s] 20÷75
Filtration ISO code 20/16 (Min. recommended fluid filtration of 25 micron)

Oil flow in drain line Pressure Losses

P
bar
14
Pressure Oil flow in 12
Viscosity
drop drain line 10
(mm 2/s)
(bar) (l/min)
8
20 1,5
140 6
35 1
4
20 3
210 2
35 2
0
0 10 20 30 40 50 60 70 80 90 100 110 120 Q, l/min

86
 EPMT
MOTORS

SPECIFICATION DATA

EPMT EPMT EPMT EPMT EPMT EPMT EPMT EPMT

Type
160 200 250 315 400 500 630 725
3
Displacement [cm /rev.] 161,1 201,4 251,8 326,3 410,9 523,6 612,3 725
Max. Speed, cont. 625 625 500 380 305 240 206 172
[RPM] Int.* 780 750 600 460 365 285 247 205
Max. Torque cont. 47 59 73 95 108 122 123 125
[daNm] Int.* 56 71 88 114 126 137 138 140
peak** 66 82 102 133 144 160 161 165
Max. Output cont. 26,5 33,5 33,5 33,5 30 26,5 24,3 20,2
[kW] int.* 32 40 40 40 35 30 27,5 26,8
Max. Pressure Drop cont. 200 200 200 200 180 160 140 115
[bar] Int.* 240 240 240 240 210 180 160 130
peak** 280 280 280 280 240 210 190 160
Max. Oil Flow cont. 100 125 125 125 125 125 125 125
[l/min] Int.* 125 150 150 150 150 150 151,4 151,4
Max. Inlet Pressure cont. 210 210 210 210 210 210 210 210
[bar] Int.* 250 250 250 250 250 250 250 250
peak** 300 300 300 300 300 300 300 300
Max. Return Pressure cont. 0-100 RPM 75 75 75 75 75 75 75 75
without Drain Line or cont. 100-300 RPM 40 40 40 40 40 40 40 40
Max. Pressure cont. >300 RPM 20 20 20 20 20 - - -
in Drain Line , [bar] Int.* 0-max. RPM 75 75 75 75 75 75 75 75
Max. Return Pressure cont. 140 140 140 140 140 140 140 140
with Drain Line Int.* 175 175 175 175 175 175 175 175
[bar] peak** 210 210 210 210 210 210 210 210
Max. Starting Pressure with Unloaded Shaft, [bar] 10 10 10 10 10 10 10 10
Min. Starting Torque at max. press. drop cont. 34 43 53 74 84 95 95 95
[daNm] at max. press. drop Int.* 41 52 63 89 97 106 108 110
Min. Speed***, [RPM] 10 9 8 7 6 5 5 5
Weight, [kg] EPMT 20 20,5 21 22 23 24 25 26
EPMTW 22 22,5 23 24 25 26 27 28
EPMTS 15 15,5 16 17 18 19 20 21
EPMTV 11 11,5 12 13 14 15 16 17

* Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds of 5 RPM lower than given, consult factory or your regional manager.
1) Intermittent speed and intermittent pressure must not occur simultaneously.
2) Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3) Recommend using a premium quality, anti-wear type mineral based hydraulic oil, HLP(DIN51524) or HM(ISO6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4) Recommended minimum oil viscosity 13 mm²/s at 50ºC.
5) Recommended maximum system operating temperature is 82ºC.
6) To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.

87
 EPMT
MOTORS
FUNCTION DIAGRAMS
EPMT 160
Cont.

Cont.

EPMT 200
Cont.

Cont.

The function diagrams data was collected at back pressure 5÷10 bar
and oil with viscosity of 32 mm²/s at 50° C.
88
 EPMT
MOTORS
FUNCTION DIAGRAMS

EPMT 250
Cont.

Cont.

EPMT 315
Cont.

Cont.

89
 EPMT
MOTORS
FUNCTION DIAGRAMS
EPMT 400
Cont.

Cont.

EPMT 500
Cont.

Cont.

The function diagrams data was collected at back pressure 5÷10 bar
and oil with viscosity of 32 mm²/s at 50° C.
90
 EPMT
MOTORS

DIMENSIONS AND MOUNTING DATA

Port A

Port B

Porting Mounting
Side Ports Square Mount (4 Holes)

T
C

P(A,B)

E Rear Ports W Wheel Mount

P(A,B) plugged

Port A

Port B

Standard Rotation Reverse Rotation

C: 4xM10-10 mm depth
Viewed from Shaft End Viewed from Shaft End
P(A,B): 2xG3/4 or 2xM27x2-17 mm depth
Port A Pressurized - CW Port A Pressurized - CCW
Port B Pressurized - CCW Port B Pressurized - CW T: G 1/4 or M14x1,5 - 12 mm depth (plugged)

Type L, mm Type L, mm L 2, mm Type L, mm Type L, mm L2 , mm *L1, mm

EPMT 160 190 EPMTE 160 200 140 EPMTW 160 123 EPMTWE 160 133 73 16,5
EPMT 200 195 EPMTE 200 205 145 EPMTW 200 128 EPMTWE 200 138 78 21,5
EPMT 250 201 EPMTE 250 211 151 EPMTW 250 134 EPMTWE 250 144 84 27,8
EPMT 315 211 EPMTE 315 221 161 EPMTW 315 144 EPMTWE 315 154 94 37,0
EPMT 400 221 EPMTE 400 231 171 EPMTW 400 154 EPMTWE 400 164 104 47,5
EPMT 500 235 EPMTE 500 245 185 EPMTW 500 168 EPMTWE 500 118178 61,5
EPMT 630 242,5 EPMTE 630 252,5 192,5 EPMTW 630 175,5 EPMTWE 630 185,5 125,5 72,5
EPMT 725 260 EPMTE 725 270 210 EPMTW 725 193 EPMTWE 725 193 143 86,5

* The width of the gerolor is 3,5 mm greater than L1.

91
 EPMT
MOTORS

SHAFT EXTENSIONS

C -ø40 straight, Parallel key A12x8x70 DIN 6885 K -tapered 1:10, Parallel key B12x8x28 DIN 6885
Max. Torque 132,8 daNm Max. Torque 210,7 daNm
S=46
Tightening Torque
50±3 daNm

max 114

max 114

CO -ø1½" straight, Parallel key 3 8"x 3 8"x 2¼" BS46 SH -ø1½" splined 17T, DP 12/24 ANSI B92.1-1976
Max. Torque 132,8 daNm Max. Torque 132,8 daNm

max 114
max 114

SL -ø34,85 p.t.o. DIN 9611 Form 1

Max. Torque 77 daNm

D
- Motor Mounting Surface
max 134

92
 EPMT
MOTORS

DIMENSIONS AND MOUNTING DATA - EPMTS and EPMTV

max L

Port A

Port B

Porting Mounting
Side Ports S - Short Mount

max 36,1
min 32,9
C
4xø14,2

P(A,B)
"O" Ring 125x3

T 8±0,2

E Rear Ports plugged

P(A,B)
V - Very Short Mount
72±0,2

max 25
Port A

Port B Drain port

"O" Ring 100x3

max L
max
72±0,2
+0,5
max L 90,5 -1,6

Standard Rotation Reverse Rotation

Viewed from Shaft End Viewed from Shaft End C : 4xM10-10 mm depth
Port A Pressurized - CW Port A Pressurized - CCW P (A,B): 2xG3/4 or 2xM27x2-17 mm depth
Port B Pressurized - CCW Port B Pressurized - CW T : G ¼ or M14x1,5 - 12 mm depth (plugged)

Type L, mm Type L, mm L 2, mm Type L, mm Type L, mm L 2, mm *L1, mm

EPMTS 160 146 EPMTSE 160 156 96 EPMTV 160 101 EPMTVE 160 111 51,5 16,5
EPMTS 200 151 EPMTSE 200 161 101 EPMTV 200 106 EPMTVE 200 116 56,5 21,5
EPMTS 250 157 EPMTSE 250 167 107 EPMTV 250 112 EPMTVE 250 122 62,8 27,8
EPMTS 315 166 EPMTSE 315 176 116 EPMTV 315 121 EPMTVE 315 131 72 37,0
EPMTS 400 177 EPMTSE 400 187 127 EPMTV 400 132 EPMTVE 400 142 82,5 47,5
EPMTS 500 191 EPMTSE 500 201 142 EPMTV 500 146 EPMTVE 500 156 96,5. 61,5
EPMTS 630 198,5 EPMTSE 630 208,5 146,5 EPMTV 630 153,5 EPMTVE 630 163,5 104 72,5
EPMTS 725 216 EPMTSE 725 226 167 EPMTV 725 171 EPMTVE 725 181 121,5 86,5

* The width of the gerolor is 3,5 mm greater than L1.

93
 EPMT
MOTORS

DIMENSIONS OF THE ATTACHED COMPONENT

EPMTS

+1
ø92

F: Oil circulation hole I: O- Ring 125x3mm

G: Internal drain channel J: 4xM12-18 mm depth, 900
H: Hardened stop plate T: Drain connection G1/4 or M14x1,5

EPMTV

depth min
Four

F: Oil circulation hole H: Hardened stop plate

G: Internal drain channel I: O- Ring 100x3mm

DRAIN CONNECTION
A drain line ought to be used when pressure in the return line can exceed the permissible pressure. It can be
connected:
- For EPMTS at the drain port of the motor;
- For EPMTV at the drain connection of the attached component. The maximum pressure in the drain line is limited
by the attached component and its shaft seal.
The drain line must be possible for oil to flow freely between motor and attached component and must be led to the
tank. The maximum pressure in the drain line is limited by the attached component and its seal.

94
 EPMT
MOTORS

INTERNAL SPLINE DATA FOR THE ATTACHED COMPONENT

Standard ANSI B92.1-1976, class 5

[m=2.1166; corrected x.m=+1,0]
Fillet Root Side Fit mm
Number of Teeth z 16
Diametral Pitch DP 12/24
Pressure Angle 30O
Pitch Dia. D 33,8656 L

Major Dia. Dri 38,4+0,4

Minor Dia. Di 32,15+0,04 Hardening Specification:
Space Width [Circular] Lo 4,516±0,037 HRC 60±2
Fillet Radius Rmin 0,5 HRC 52
Max. Measurement between Pin L 26,9+0,10 0,7±0,2 mm effective case depth
Pin Dia. d 4,835±0,001 Material 20 MoCr4 DIN 17210 or better

PERMISSIBLE SHAFT LOADS

The output shaft runs in tapered bearings that permit high axial and radial forces.
Curve "1" shows max. radial shaft load. Any shaft load exceeding the values quoted in the curve will seriously reduce motor
life. The two other curves apply to a B10 bearing life of 3000 hours at 200 RPM.

Prad (daN) 1
5000

4000

3000

2000 Pa=0
Pa=1000 daN

1000

0
50 100 150 180 (mm)
max 114

Pamax=1000 daN

max 181

Pamax=1000 daN

95
 EPMT
MOTORS

MOTORS WITH TACHO CONNECTION

ORDER CODE

1 2 3 4 5 6 7 8 9 10

EPMT

Pos.1 - Mounting Flange Pos. 5 - Ports

omit - Square mount, four holes omit - BSPP (ISO 228)
S - Short mount M - Metric (ISO 262)
V - Very short mount
W - Wheel mount Pos. 6 - Speed Monitoring
omit - none
Pos.2 - Port type T - with tacho connection (only for side ports)
omit - Side ports
E - Rear ports Pos. 7 - Special Features
omit - none
Pos.3 - Displacement code LL -Low Leakage
160 - 161,1[cm3/rev] LSV - Low Speed Valve
200 - 201,4[cm3/rev]
250 - 251,8[cm3/rev] Pos. 8 - Rotation
315 - 326,3[cm3/rev] omit - Standard Rotation
400 - 410,9[cm3/rev] R - Reverse Rotation
500 - 523,6[cm3/rev]
Pos. 9 - Option (Paint)**
630 - 612,3[cm3/rev] (without Function diagram)
omit - no Paint
725 - 725,0[cm3/rev] (without Function diagram)
P - Painted
Pos.4 - Shaft Extensions* PC - Corrosion Protected Paint
C - ø40 straight, Parallel key A12x8x70 DIN6885 Pos.10 - Design Series
CO - ø1½ ” straight, Parallel key 3/8”x3/8”x2¼” BS46 omit - Factory specified
K - ø45 tapered 1:10, Parallel key B12x8x28 DIN6885
SL - ø34,85 p.t.o. DIN 9611 Form 1
SH - ø1½" splined 17T ANSI B92.1-1976

NOTES:
* The permissible output torque for shafts must be not exceeded!
** Color at customer's request.

The hydraulic motors are mangano-phosphatized as standard.

96