Worldwide

www.tyco-fire.com
Contacts

Pipe Fittings
NPT Threaded,
Ductile Iron
General Technical
Description Data
The TYCO Series 800 Threaded Pipe Approvals
Fittings and California Tees & Elbows UL Listed
are manufactured from ductile iron. FM Approved
They are stronger and more corrosion
Maximum Working Pressure
resistant than cast iron fittings. The
300 psi (20,7 bar)
additional strength is provided by the
ductile properties and by adding mag- Material
nesium while the iron is being poured Series 800 and California Fittings:
into the final cast shape. Although Ductile Iron
lighter than standard cast iron, the Figure 719 Plug:
fittings have an added advantage of Cast Iron
being less susceptible to cracking due
to their added strength. Pipe Thread
NPT per ANSI B1.20.1
The Series 800, California, and Figure
719 Threaded Pipe Fittings are a re-
Limited
designation for the Central Series 800, Installation Warranty
California, and Figure 719 Threaded Apply TEFLON tape or high quality pipe
Pipe Fittings. joint compound on male pipe threads For warranty terms and conditions, visit
and tighten two to three turns beyond www.tyco-fire.com.
NOTICE hand tight.
The Threaded Pipe Fittings described Ordering
herein must be installed and main- NOTICE
tained in compliance with this docu- Installers who have not used ductile iron
Procedure
ment, as well as with the applicable threaded fittings should be instructed Contact your local distributor for avail-
standards of the NATIONAL FIRE PRO- that the fittings are stronger than the ability. When placing an order, indicate
TECTION ASSOCIATION (NFPA), in pipe and overtightening the fitting can the full product name and Part Number
addition to the standards of any other create leaks and cause damage to pipe (P/N).
authorities having jurisdiction. Failure threads. In general, there is about one-
to do so may impair the performance half turn difference between cast iron
of these devices. and ductile iron fittings. Apply TEFLON
The owner is responsible for main- tape or high quality pipe joint com-
taining their fire protection system pound on the male pipe threads and
and devices in proper operating con- tighten two to three turns beyond hand
dition. Contact the installing contrac- tight. If an automatic make-on machine
tor or product manufacturer with any is being used, please exercise caution
questions. in setting the machine to the proper
parameters prior to tightening fittings
onto the male pipe threads.
 IMPORTANT
Refer to Technical Data Sheet
TFP2300 for warnings pertaining to
regulatory and health information.
Page 1 of 10 AUGUST 2018 TFP1710
TFP1710
Page 2 of 10

A
A

B B

B A B
A

FIGURE 811 FIGURE 813

90° ELBOW 45° ELBOW

Nominal Pipe Figure 811 Figure 813

Size

ANSI A B Approx. A B Approx.

Weight Part Weight Part
Inches Inches Inches Inches Inches
Lbs. Number Lbs. Number
DN (mm) (mm) (mm) (mm)
(kg) (kg)
1/2 1.13 0.56 0.24 0.88 0.38 0.22
86206 86780
15 (28,7) (14,2) (0,11) (22,4) (9,7) (0,09)
3/4 1.31 0.75 0.40 1.00 0.44 0.33
20 (33,3) (19,0) (0,18) 86205 (25,4) (11,2) (0,15) 86781
1 1.50 0.81 0.64 1.13 0.81 0.48
25 (38,1) (20,6) (0,29) 86200 (28,7) (20,6) (0,21) 86280
1-1/4 1.75 1.06 0.95 1.31 0.63 0.73
86201 86281
32 (44,5) (26,9) (0,43) (33,3) (16,0) (0,33)
1-1/2 1.94 1.19 1.24 1.44 0.69 0.93
86202 86282
40 (49,3) (30,2) (0,56) (36,6) (17,5) (0,42)
2 2.25 1.50 1.74 1.68 0.94 1.55
50 (57,1) (38,1) (0,79) 86203 (42,7) (23,9) (0,70) 86283
2-1/2 2.69 1.56 3.28 1.94 1.00 2.70
86204 86782
65 (68,3) (39,6) (1,49) (49,3) (25,4) (1,22)
TABLE A
FIGURES 811 & 813
NOMINAL DIMENSIONS
 TFP1710
Page 3 of 10

D
C A

FIGURE 812
90° REDUCING ELBOW

Nominal Pipe
Size Figure 812

ANSI A B C D Approx.
Weight Part
Inches Inches Inches Inches Inches Lbs. Number
DN (mm) (mm) (mm) (mm) (kg)
3/4 x 1/2 1.19 1.19 0.63 0.63 0.33
86342
20 x 15 (30,2) (30,2) (16,0) (16,0) (0,15)
1 x 1/2 1.25 1.38 0.56 0.81 0.44
86210
25 x 15 (31,8) (35,1) (14,2) (20,6) (0,20)
1 x 3/4 1.38 1.44 0.69 0.88 0.53
86211
25 x 20 (35,1) (36,6) (17,5) (22,4) (0,24)
1-1/4 x 1/2 1.31 1.50 0.63 0.94 0.64
86212
32 x 15 (33,3) (38,1) (16,0) (23,9) (0,29)
1-1/4 x 3/4 1.44 1.63 0.75 1.06 0.75
86213
32 x 20 (36,6) (41,4) (19,0) (26,9) (0,34)
1-1/4 x 1 1.56 1.68 0.88 1.00 0.77
86214
32 x 25 (39,6) (42,7) (22,4 (25,4) (0,35)
1-1/2 x 3/4 1.50 1.75 0.75 1.19 0.95
86221
40 x 20 (38,1) (44,4) (19,0) (30,2) (0,43)
1-1/2 x 1 1.63 1.81 0.88 1.13 0.99
86215
40 x 25 (41,4) (46,0) (22,4) (28,7) (0,45)
1-1/2 x 1-1/4 1.81 1.88 1.13 1.19 1.14
86216
40 x 32 (46,0) (47,8) (28,7) (30,2) (0,52)
2 x 3/4 1.63 1.94 0.88 1.38 1.39
86217
50 x 20 (41,4) (49,3) (22,4) (35,1) (0,63)
2x1 1.75 2.06 2.00 1.31 1.58
86218
50 x 25 (44,4) (52,3) (50,8) (33,3) (0,72)
2 x 1-1/2 2.00 2.19 1.25 1.44 1.67
86220
50 x 40 (50,8) (55,6) (31,8) (36,6) (0,76)
2-1/2 x 2 2.38 2.63 1.25 1.88 3.01
86762
65 x 50 (60,5) (66,8) (31,8) (47,8) (1,36)

TABLE B
FIGURE 812
NOMINAL DIMENSIONS
TFP1710
Page 4 of 10

A A

D B
C

C
D B

FIGURE 817
CROSS

Nominal Pipe Size Figure 817

ANSI A B C D Approx.
Weight Part
Inches Inches Inches Inches Inches Lbs. Number
DN (mm) (mm) (mm) (mm) (kg)
1 1.50 1.50 0.81 0.81 0.97
86284
25 (38,1) (38,1) (20,6) (20,6) (0,44)
1-1/4 1.75 1.75 1.06 1.06 1.59
86285
32 (44,4) (44,4) (26,9) (27,0) (0,72)
1-1/2 1.94 1.94 1.19 1.19 1.89
86286
40 (49,3) (49,3) (30,2) (30,2) (0,86)
2 2.25 2.25 1.50 1.50 2.93
86287
50 (57,1) (57,1) (38,1) (38,1) (1,33)
1-1/4 x 1-1/4 x 1 x 1 1.69 1.56 1.00 0.88 1.25
86289
32 x 32 x 25 x 25 (42,9) (39,6) (25,4) (22,4) (0,56)
1-1/2 x 1-1/2 x 1 x 1 1.81 1.63 1.06 1.94 1.48
86322
40 x 40 x 25 x 25 (46,0) (41,4) (26,9) (49,3) (0,71)
2x2 x1 x1 2.00 1.75 1.25 1.06 2.64
86291
50 x 50 x 25 x 25 (50,8) (44,4) (31,8) (26,9) (1,20)

TABLE C
FIGURE 817
NOMINAL DIMENSIONS
 TFP1710
Page 5 of 10

A B
B
B A
B
A

FIGURE 818
FIGURE 814 STRAIGHT COUP LING
IRON TEE

Nominal Pipe
Size Figure 814 Figure 818

ANSI A B Approx. A B Approx.

Weight Part Weight Part
Inches Inches Inches Inches Inches
Lbs. Number Lbs. Number
DN (mm) (mm) (mm) (mm)
(kg) (kg)
1/2 1.13 0.56 0.33 1.38 0.31 0.18
86340 72779
15 (28,7) (14,2) (0,15) (35,1) (7,9) (0,08)
3/4 1.31 0.75 0.50 1.63 0.56 0.26
86341 72778
20 (33,3) (19,0) (0,23) (41,4) (14,0) (0,11)
1 1.50 0.81 0.85 1.75 0.38 0.44
86230 72755
25 (38,1) (20,6) (0,38) (44,4) (9,7) (0,20)
1-1/4 1.75 1.06 1.30 2.00 0.56 0.54
86231 72754
32 (44,4) (26,9) (0,59) (50,8) (14,0) (0,24)
1-1/2 1.94 1.19 1.63 2.19 0.75 0.71
86232 72753
40 (49,3) (30,2) (0,74) (55,6) (19,0) (0,32)
2 2.25 1.50 2.63 2.63 1.13 1.15
86233 72752
50 (57,1) (38,1) (1,19) (66,8) (28,7) (0,52)
2-1/2 2.69 1.56 4.55 3.00 0.75 2.29
86234 72758
65 (68,3) (39,6) (2,06) (76,2) (19,0) (1,04)

TABLE D
FIGURES 814 & 818
NOMINAL DIMENSIONS
TFP1710
Page 6 of 10

B
E
F

A D

FIGURE 815
REDUCING TEE

Nominal Pipe Size Figure 815

ANSI A B C D E F Approx.
Weight Part
Inches Inches Inches Inches Inches Inches Inches Lbs. Number
DN (mm) (mm) (mm) (mm) (mm) (mm) (kg)
3/4 x 3/4 x 1/2 1.19 1.19 1.25 0.63 0.63 0.69 0.46
86235
20 x 20 x 15 (30,2) (30,2) (31,8) (16,0) (16,0) (17,5) (0,21)
3/4 x 3/4 x 1 1.44 1.44 1.38 0.88 0.88 0.69 0.68
86755
20 x 20 x 25 (36,6) (36,6) (35,1) (22,4) (22,4) (17,5) (0,31)
1 x 1/2 x 1 1.50 1.38 1.50 0.81 0.81 0.81 0.70
86236
25 x 15 x 25 (38,1) (35,1) (38,1) (20,6) (20,6) (20,6) (0,32)
1 x 3/4 x 1/2 1.25 1.19 1.38 0.56 0.63 0.81 0.63
86756
25 x 20 x 15 (31,8) (30,2) (35,1) (14,2) (16,0) (20,6) (0,28)
1 x 3/4 x 3/4 1.38 1.31 1.44 0.69 0.75 0.88 0.68
86757
25 x 20 x 20 (35,1) (33,3) (36,6) (17,5) (19,0) (22,4) (0,31)
1 x 3/4 x 1 1.50 1.44 1.50 0.81 0.88 0.81 0.77
86237
25 x 20 x 25 (38,1) (36,6) (38,1) (20,6) (22,4) (20,6) (0,35)
1 x 1 x 1/2 1.25 1.25 1.38 0.56 0.56 0.81 0.66
86238
25 x 25 x 15 (31,8) (31,8) (35,1) (14,3) (14,3) (20,6) (0,30)
1 x 1 x 3/4 1.38 1.38 1.44 0.69 0.69 0.88 0.73
86239
25 x 25 x 20 (35,1) (35,1) (36,6) (17,5) (17,5) (22,4) (0,33)
1 x 1 x 1-1/4 1.69 1.69 1.56 1.00 1.00 0.88 0.97
86240
25 x 25 x 32 (42,9) (42,9) (39,6) (25,4) (25,4) (22,4) (0,44)
1 x 1 x 1-1/2 1.81 1.81 1.63 1.13 1.13 0.88 1.14
86241
25 x 25 x 40 (46,0) (46,0) (41,4) (28,6) (28,6) (22,4) (0,52)
1-1/4 x 1 x 1/2 1.94 1.25 1.56 0.63 0.56 1.00 0.81
86242
32 x 25 x 15 (49,2) (31,8) (39,6) (15,9) (14,3) (25,4) (0,37)
1-1/4 x 1 x 3/4 1.44 1.38 1.62 0.75 0.69 1.06 0.90
86243
32 x 25 x 20 (36,6) (35,1) (41,2) (19,0) (17,5) (27,0) (0,41)
1-1/4 x 1 x 1 1.56 1.50 1.69 0.88 0.81 1.00 1.03
86244
32 x 25 x 25 (39,6) (38,1) (42,9) (22,4) (20,6) (25,4) (0,47)
1-1/4 x 1 x 1-1/4 1.75 1.69 1.75 1.06 1.00 1.06 1.10
86245
32 x 25 x 32 (44,4) (42,9) (44,4) (27,0) (25,4) (27,0) (0,50)
1-1/4 x 1 x 1-1/2 1.88 1.81 1.81 1.19 1.13 1.06 1.43
86246
32 x 25 x 40 (47,6) (46,0) (46,0) (30,1) (28,6) (27,0) (0,65)
1-1/4 x 1-1/4 x 1/2 1.38 1.38 1.56 0.69 0.69 1.00 0.87
32 x 32 x 15 (35,1) (35,1) (39,6) (17,5) (17,5) (25,4) (0,39) 86247
1-1/4 x 1-1/4 x 3/4 1.44 1.44 1.63 0.75 0.75 1.06 0.96
86248
32 x 32 x 20 (36,6) (36,6) (41,4) (19,0) (19,0) (27,0) (0,43)
1-1/4 x 1-1/4 x 1 1.56 1.56 1.69 0.88 0.88 1.00 1.10
86249
32 x 32 x 25 (39,6) (39,6) (42,9) (22,4) (22,4) (25,4) (0,50)
1-1/4 x 1-1/4 x 1-1/2 1.88 1.88 1.81 1.81 1.81 1.06 1.50
86250
32 x 32 x 40 (47,6) (47,6) (46,0) (46,0) (46,0) (27,0) (0,68)
1-1/4 x 1-1/4 x 2 2.13 2.13 2.00 1.44 1.44 1.13 2.00
86251
32 x 32 x 50 (54,1) (54,1) (50,8) (36,6) (36,6) (28,6) (0,91)
1-1/2 x 1 x 1/2 1.44 1.31 1.69 0.69 0.63 1.13 0.97
86252
40 x 25 x 15 (36,6) (33,3) (42,9) (17,5) (15,9) (28,6) (0,44)
1-1/2 x 1 x 3/4 1.50 1.38 1.75 0.75 0.69 1.19 1.14
86253
40 x 25 x 20 (38,1) (35,1) (44,4) (19,0) (17,5) (30,2) (0,52)
1-1/2 x 1 x 1 1.63 1.50 1.81 0.88 0.81 1.13 1.14
86254
40 x 25 x 25 (41,4) (38,1) (46,0) (22,4) (20,6) (28,7) (0,52)
1-1/2 x 1 x 1-1/2 1.94 1.81 1.94 1.19 1.13 1.19 1.52
86256
40 x 25 x 40 (49,3) (46,0) (49,2) (30,2) (28,6) (30,2) (0,69)

TABLE E (1 OF 2)
FIGURE 815
NOMINAL DIMENSIONS
 TFP1710
Page 7 of 10

B
E
F

A D

FIGURE 815
REDUCING TEE

Nominal Pipe Size Figure 815

ANSI A B C D E F Approx.
Weight Part
Inches Inches Inches Inches Inches Inches Inches Lbs. Number
DN (mm) (mm) (mm) (mm) (mm) (mm) (kg)
1-1/2 x 1-1/4 x 1/2 1.44 1.31 1.69 0.69 0.63 1.13 1.03
86257
40 x 32 x 15 (36,6) (33,3) (42,9) (17,5) (16,0) (28,7) (0,47)
1-1/2 x 1-1/4 x 3/4 1.50 1.44 1.75 0.75 0.75 1.19 1.10
86258
40 x 32 x 20 (38,1) (36,6) (44,5) (19,0) (19,0) (30,1) (0,50)
1-1/2 x 1-1/4 x 1 1.63 1.56 1.81 0.88 0.88 1.13 1.31
86259
40 x 32 x 25 (41,4) (39,7) (46,0) (22,4) (22,4) (28,7) (0,59)
1-1/2 x 1-1/4 x 2 2.19 2.13 2.00 1.44 1.44 1.25 1.94
86260
40 x 32 x 50 (55,6) (54,1) (50,8) (36,6) (36,6) (57,1) (0,88)
1-1/2 x 1-1/2 x 1/2 1.44 1.44 1.69 0.69 0.69 1.13 1.14
86261
40 x 40 x 15 (36,6) (36,6) (42,9) (17,5) (17,5) (28,7) (0,52)
1-1/2 x 1-1/2 x 3/4 1.50 1.50 1.75 0.75 0.75 1.19 1.23
40 x 40 x 20 (38,1) (38,1) (44,4) (19,0) (19,0) (30,1) (0,56) 86262
1-1/2 x 1-1/2 x 1 1.63 1.63 1.81 0.88 0.88 1.13 1.38
86263
40 x 40 x 25 (41,2) (41,2) (46,0) (22,4) (22,4) (28,7) (0,62)
1-1/2 x 1-1/2 x 1-1/4 1.81 1.81 1.88 1.06 1.06 1.19 1.50
86264
40 x 40 x 32 (46,0) (46,0) (47,6) (27,0) (27,0) (30,1) (0,68)
1-1/2 x 1-1/2 x 2 2.19 2.19 2.00 1.44 1.44 1.25 2.00
86265
40 x 40 x 50 (55,5) (55,5) (50,8) (36,6) (36,6) (31,7) (0,91)
2x1 x2 2.25 2.00 2.25 1.50 1.31 1.50 2.18
86266
50 x 25 x 50 (57,2) (50,8) (57,2) (38,1) (33,3) (38,1) (0,99)
2 x 1-1/4 x 2 2.25 2.13 2.25 1.50 1.44 1.50 2.31
86267
50 x 32 x 50 (57,2) (54,1) (57,2) (38,1) (36,6) (38,1) (1,05)
2 x 1-1/2 x 1/2 1.50 1.44 1.88 0.75 0.69 1.31 1.50
86268
50 x 40 x 15 (38,1) (36,6) (47,8) (19,0) (17,5) (33,3) (0,68)
2 x 1-1/2 x 3/4 1.63 1.50 1.94 0.88 0.75 1.38 1.61
86269
50 x 40 x 20 (41,4) (38,1) (49,3) (22,4) (19,0) (35,0) (0,73)
2 x 1-1/2 x 1 1.75 1.63 2.00 1.00 0.88 1.31 1.65
50 x 40 x 25 (44,5) (41,4) (50,8) (25,4) (22,4) (33,3) (0,75) 86270
2 x 1-1/2 x 1-1/2 2.06 1.94 2.19 1.31 1.19 1.44 2.03
86272
50 x 40 x 40 (52,4) (49,2) (55,5) (33,3) (30,2) (36,6) (0,92)
2 x 1-1/2 x 2 2.25 2.19 2.50 1.50 1.44 1.50 2.37
86273
50 x 40 x 50 (57,1) (55,5) (63,5) (38,1) (36,6) (38,1) (1,07)
2 x 2 x 1/2 1.50 1.50 1.88 0.75 0.75 1.31 1.50
86222
50 x 50 x 15 (38,1) (38,1) (47,8) (19,0) (19,0) (33,3) (0,68)
2 x 2 x 3/4 1.63 1.63 1.94 0.88 0.88 1.38 1.67
86223
50 x 50 x 20 (41,4) (41,4) (49,3) (22,4) (22,4) (35,0) (0,76)
2x2 x1 1.75 1.75 2.00 1.00 1.00 1.31 1.91
86224
50 x 50 x 25 (44,5) (44,5) (50,8) (25,4) (25,4) (33,3) (0,86)
2 x 2 x 1-1/4 1.88 1.88 2.13 1.13 1.13 1.44 2.05
86225
50 x 50 x 32 (47,8) (47,8) (54,1) (28,7) (28,7) (36,6) (0,93)
2 x 2 x 1-1/2 2.00 2.00 2.19 1.25 1.25 1.50 2.11
86226
50 x 50 x 40 (50,8) (50,8) (55,6) (31,8) (31,8) (38,1) (0,96)
2 x 2 x 2-1/2 2.63 2.63 2.38 1.75 1.88 1.44 3.67
86227
50 x 50 x 65 (66,8) (66,8) (60,5) (44,5) (47,8) (36,6) (1,66)
2-1/2 x 2 x 3/4 1.75 1.63 2.31 0.63 0.88 1.75 2.22
86274
65 x 50 x 20 (44,5) (41,4) (58,7) (15,9) (22,4) (44,5) (1,01)

TABLE E (2 OF 2)
FIGURE 815
NOMINAL DIMENSIONS
TFP1710
Page 8 of 10

A B A A

FIGURE 820 FIGURE 830 FIGURE 719

CAP BRASS SEAT UNION PLUG

Nominal Pipe
Size Figure 820 Figure 830 Figure 719

ANSI A Approx. A B Approx. A Approx.

Weight Part Weight Part Weight Part
Inches Inches Lbs. Inches Inches Lbs. Inches Lbs.
Number Number Number
DN (mm) (kg) (mm) (mm) (kg) (mm) (kg)
1/2 0.88 0.15 1.88 0.81 0.47 0.94 0.10
72776 86207 86292
15 (22,4) (0,06) (47,8) (20,6) (0,21) (23,9) (0,04)
3/4 1.00 0.22 2.00 0.94 0.66 1.13 0.18
20 (25,4) (0,10) 72777 (50,8) (23,9) (0,30) 86275 (28,7) (0,08) 86293
1 1.18 0.33 2.19 0.81 1.08 1.25 0.28
72824 86276 86294
25 (30,0) (0,15) (55,6) (20,6) (0,49) (31,7) (0,13)
1-1/4 1.31 0.54 2.50 1.06 1.54 1.38 0.50
32 (33,3) (0,24) 72756 (63,5) (26,9) (0,70) 86277 (35,1) (0,23) 86295
1-1/2 1.38 0.68 2.63 1.19 2.03 1.44 0.70
72822 86278 86296
40 (35,1) (0,31) (66,8) (30,2) (0,92) (36,6) (0,32)
2 1.50 0.96 3.13 1.63 3.15 1.50 0.90
72823 86279 86297
50 (38,1) (0,43) (79,5) (41,4) (1,43) (38,1) (0,41)
2-1/2 1.75 1.80
65 (44,5) (0,82) 72825 — — — — — — —

TABLE F
FIGURES 820, 830 & 719
NOMINAL DIMENSIONS
 TFP1710
Page 9 of 10

B A

FIGURE 825 FIGURE 827 FIGURE 816

EXTENSION PIECE HEX BUSHING REDUCING COUPLING

Nominal Pipe Figure 825 Figure 827 Figure 816

Size Extension Piece Hex Bushing Reducing Coupling

ANSI A Approx. A Approx. A B Approx.

Weight Part Weight Part Weight Part
Inches Inches Inches Inches Inches
Lbs. Number Lbs. Number Lbs. Number
DN (mm) (mm) (mm) (mm)
(kg) (kg) (kg)
1/2 x 1/2 1.50 0.20
72751 — — — — — — —
15 x 15 (38,1) (0,09)
1/2 x 1/2 2.00 0.27
72980 — — — — — — —
15 x 15 (50,8) (0,12)
3/4 x 3/4 1.50 0.22
20 x 20 (38,1) (0,10) 72981 — — — — — — —
3/4 x 3/4 2.00 0.31
20 x 20 (50,8) (0,14) 73982 — — — — — — —
3/4 x 1/2 1.75 0.69 0.38
20 x 15 — — — — — — (43,2) (17,5) (0,17) 86772
1 x 1/2 1.06 0.22 1.69 0.50 0.38
— — — 72726 86228
25 x 15 (26,9) (0,10) (42,9) (12,7) (0,17)
1 x 3/4 1.06 0.18 1.75 0.50 0.53
25 x 20 — — — (26,9) (0,08) 72762 (43,2) (12,7) (0,24) 86229
1-1/4 x 1 1.19 0.31
32 x 25 — — — (30,2) (0,14) 72763 — — — —
1-1/2 x 1 1.25 0.53
— — — 72757 — — — —
40 x 25 (31,7) (0,24)
1-1/2 x 1-1/4 1.25 0.35
— — — 72764 — — — —
40 x 32 (31,7) (0,10)
2x1 1.38 0.75
— — — 72759 — — — —
50 x 25 (35,1) (0,34)
2 x 1-1/4 1.38 0.69
— — — 72761 — — — —
50 x 32 (35,1) (0,31)
2 x 1-1/2 1.38 0.62
50 x 40 — — — (35,1) (0,28) 72775 — — — —

TABLE G
FIGURE 825, 827 & 816
NOMINAL DIMENSIONS
TFP1710
Page 10 of 10

A A
B C B C

D D

FIGURE 832
CALIFORNIA TEES

Nominal Pipe
Size Figure 832

ANSI A B C D Approx.
Weight Part
Inches Inches Inches Inches Inches Lbs. Number
DN (mm) (mm) (mm) (mm) (kg)
1 x 1/2 x 1 1.50 0.88 0.75 3.00 0.95
42000
25 x 15 x 25 (38,1) (22,4) (19,1) (76,2) (0,43)
1x1x1 1.50 0.75 0.75 3.00 0.95
42001
25 x 25 x 25 (38,1) (19,1) (19,1) (76,2) (0,43)

TABLE H
FIGURE 832
NOMINAL DIMENSIONS

C C

A B A B

FIGURE 831
STREET ELBOWS
Nominal Pipe
Size Figure 831

ANSI A B C Approx.
Weight Part
Inches Inches Inches Inches Lbs. Number
DN (mm) (mm) (mm) (kg)
1 x 1/2 1.50 0.75 3.00 0.70
42003
25 x 15 (38,1) (19,1) (76,2) (0,32)
1x1 1.50 0.75 3.00 0.90
42002
25 x 25 (38,1) (19,1) (76,2) (0,40)

TABLE J
FIGURE 831
NOMINAL DIMENSIONS

1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone +1-215-362-0700

© 2018 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.

NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered trademarks of National Fire Protection Association;
TEFLON is a registered trademark of DuPont