MasterSeal® 910

Water swelling waterbar for joints

DESCRIPTION PACKAGING
MasterSeal 910 Waterbar is suitable for all 20 x 10 mm (± 5%) 30 linear metres per carton.
construction joints subject to hydrostatic pressure,
on one or both sides. MasterSeal 910 provide TYPICAL PROPERTIES*
simple but efficient waterproofing of construction
joints. Movements in the joint, e.g. by shrinkage or Basis polymer composite
settlement in the substrate, are taken up by the Water seepage (when none
elastic profile of the MasterSeal 910 Waterbar. placed in expansion joint)
MasterSeal 910 has been successfully employed Application temperatures -30°C to +50°C
to waterproof joints where an opening of up to Freeze / thaw resistance no influence before and
5mm was deliberately created. Water pressure of after concreting
up to 5 bar was sealed.
APPLICATION GUIDELINES
MasterSeal 910 is based on a newly developed
polymer technology providing flexible polymer
SURFACE PREPARATION
composites which have high chemical resistance
capable of storing water in their molecular All joints to be waterproofed with MasterSeal 910
structure by increasing their volume. Waterbars must first be cleaned. Free standing
water and sharp protrusions must be avoided.
Where previously MasterSeal 910 was available MasterSeal 910 Waterbars can be installed on
in different grades for various exposure conditions. moist or frozen surfaces.
A single version of MasterSeal 910 now resists
deterioration in the following conditions: In fresh MasterSeal 910 Waterbars are resistant to most
water and where the water has a high salt content ordinary mould release agents, but if in doubt the
(sea water, brackish water), in construction with installed waterbar should always be protected from
high chemical exposure and/or exposure of accidental exposure to form release agents.
solvents, including oils and fuels.
PLACING / APPLICATION
MasterSeal 910 is a component of the Master For normal joint widths of 200-400 mm,
Builders Solutions pile-cap waterproofing and MasterSeal 910 is placed in the middle of the
watertight jointing systems. Consult your joint. For added safety thicker walls can be fitted
representative for details. with 2 waterbars.

ADVANTAGES MasterSeal 910 Waterbars are glued into the joint

When in contact with water the MasterSeal 910 with a special adhesive for MasterSeal 910
Waterbars will slowly increase in volume (swell) Waterbars. On vertical surfaces the
without changing the homogeneous structure of MasterSeal 910 is temporarily fixed to the
the polymer matrix. The increase in volume by the construction joint with a nail until the adhesive
swelling action can be up to 200% (depending on dries.
type of water). The pressure of the swelling action
will cause the MasterSeal 910 Waterbar to profile
itself exactly into the joint filling all cavities and
effectively stopping water seepage, even at high
external water pressure.

The MasterSeal 910 Waterbars will not transport

water through their polymer matrix and thus not
act as a capillary duct. The swelling action is
limited to the sides exposed to water.
MasterSeal® 910

MasterSeal 910 Waterbar MUST always be QUALITY AND CARE

secured so that the waterbar is in close contact All products originating from Master Builders
with the surface of the substrate otherwise the full Solutions Dubai, UAE facility are manufactured
waterproofing effect will not be obtained. under a management system independently
certified to conform to the requirements of the
After placing the MasterSeal 910 Waterbar the quality, environmental and occupational health &
joint area should be kept clean and free of loose safety standards ISO 9001 and ISO 14001.
dirt and stones before concreting. The minimum
concrete cover of MasterSeal 910 Waterbar is
80 mm. * Properties listed are based on laboratory controlled tests.

® = Registered trademark of the MBCC Group in many countries.

BUTT JOINTS
MasterSeal 910 Waterbars should never be glued
at butt joints but laid with a 20 mm overlap.

STORAGE AND SHELF LIFE

Store under cover out of direct sunlight and protect
from extremes of temperature. In tropical climates
the product must be stored in an air-conditioned
environment.
The shelf life is 12 months when stored as above.

Failure to comply with the recommended storage

conditions may result in premature deterioration of
the product or packaging. For specific storage and
disposal instructions refer to the Material Safety
Data Sheet.

HEALTH AND SAFETY

As with all chemical products, care should be
taken during use and storage to avoid contact with
eyes mouth, skin and foodstuffs. If accidentally
ingested, seek immediate medical attention.
Reseal containers after use. For further
information, refer to material safety data sheet.

MBS_CC-UAE/Sl_910_12_94/v1/11_13/v2/12_19
The technical information and application advice given in this Master Builders Solutions publication are based on
STATEMENT OF the present state of our best scientific and practical knowledge. As the information herein is of a general nature, no
RESPONSIBILITY assumption can be made as to a product's suitability for a particular use or application and no warranty as to its
accuracy, reliability or completeness either expressed or implied is given other than those required by law. The user
is responsible for checking the suitability of products for their intended use.

Field service where provided does not constitute supervisory responsibility. Suggestions made by Master Builders
NOTE Solutions either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since
they, and not Master Builders Solutions, are responsible for carrying out procedures appropriate to a specific
application.

Master Builders Solutions Disclaimer: the TUV mark

Construction Chemicals LLC relates to certified management
P.O. Box 37127, Dubai, UAE system and not to the product
Tel: +971 4 8090800 mentioned on this datasheet
www.master-builders-solutions.com/en-ae