Key Programming

Contents
3 Series ................................................................................................................................................................................................ 2
3190-3193-3198-3900-3998 (Remote: 7777) ............................................................................................................................. 2
3868 Plip Upgrade – Auto Learning.............................................................................................................................................. 2
4 Series ................................................................................................................................................................................................ 3
4100-4198-4138 (Remote: 8722-2-Button, 8723-3 Button, 8015-5 Button) ................................................................................ 3
4435 (Remote: 8772).................................................................................................................................................................. 3
4 Series (Continued) ............................................................................................................................................................................ 4
4615-4625-4693-4698 (Remote: 8772 or ADR Card: NAV117A).................................................................................................. 4
6 Series ................................................................................................................................................................................................ 4
6402-6422 (Remote: 7777) ........................................................................................................................................................ 4
7 Series ................................................................................................................................................................................................ 5
7908-7928 (Remote: 7777) ........................................................................................................................................................ 5
Adding a 7 Series Touch Key (937) ............................................................................................................................................... 5
7518 (Five Button Remote: 7775) ............................................................................................................................................... 5
8 Series ................................................................................................................................................................................................ 6
8165-8185-8186-8188 (Remote: 7777) ...................................................................................................................................... 6
Adding a 8 Series Touch Key (937) ............................................................................................................................................... 6
G Series ................................................................................................................................................................................................ 6
G100-193-198 (Remote: 8772) ................................................................................................................................................... 7
G300-368 Procedure for adding new Driver Cards ........................................................................................................................ 7
Remote Central Door Locking............................................................................................................................................................... 7
1046 (Remote: 7777).................................................................................................................................................................. 7
Immobiliser .......................................................................................................................................................................................... 8
8510 (Touch Key: 937) ................................................................................................................................................................ 8
0802T (Touch Key: 937) .............................................................................................................................................................. 8
Pre-Coded Remote Keys ....................................................................................................................................................................... 8
6019-6019MKII - NO LONGER AVAILABLE .................................................................................................................................... 8
832-832SU .................................................................................................................................................................................. 8
5801 ........................................................................................................................................................................................... 8

PLEASE NOTE: SYSTEMS MUST BE IN A DISARMED STATE TO ENTER PROGRAMMING MODE

Page 0

Page 1 of 8
Ref: VOD/SF/639 Rev 1.0
Date: 04 November 2015 Uncontrolled If Printed or Copied Document Owner: B Scott / N Grove
Key Programming

3 Series
3190-3193-3198-3900-3998 (Remote: 7777)
If you have at least one working remote proceed as follows:

1. Disarm the system

2. Open drivers door and bonnet
3. Switch the ignition ON
4. Press and hold button A until the indicators flash once
5. Enter the PIN code via the button on the emergency override panel
6. The indicators will illuminate and the LED will illuminate permanently indicating that you are in ‘Auto-Learning Mode’
7. Press and hold both the buttons on the new remote, the LED between the buttons will flash, hold buttons until the LED
extinguishes
8. Release both buttons, the LED between the buttons will illuminate permanently
9. Press button A of the remote, the LED will flash, the LED on the emergency override panel will blink and the indicators will
flash confirming the addition of the remote
10. Repeat steps 7, 8 and 9 for ALL remotes including the original remote(s)
11. The system will automatically exit auto-learning if no operations are carried out within 30 seconds or the bonnet is closed

If you do not have any working remotes proceed as follows:

a. Disarm the system using the PIN code

b. Disconnect the alarm power supply
c. Open the drivers door and bonnet
d. Switch the ignition on
e. Reconnect the alarm power supply
f. Enter the PIN code
g. The LED on the emergency override panel with illuminate to 2 seconds confirming the correct PIN code
h. After 5 seconds the LED on the emergency override panel will blink indicating the it is in ‘Auto-Learning Mode’
i. Follow steps 7, 8 and 9 from above to add remotes

Note: A maximum of four remotes can be stored on the alarm system. Adding a new remote will erase all previously stored remotes.

3868 Plip Upgrade – Auto Learning

1. Disarm the system
2. Open the drivers door and bonnet
3. Switch ignition ON
4. Input the PIN code using the button on the emergency override panel
5. The indicators will flash once every 10 seconds to confirm you have entered programming table 1
6. Switch ignition OFF then ON, the indicators will flash twice every 10 seconds to confirm you have entered program table 2
7. Press and hold the button on the emergency override panel for no less than 2 seconds
8. Switch the ignition OFF and remove the key
9. Close the driver’s door
10. When the LED on the emergency override panel starts to flash rapidly press LOCK on the original vehicle remote
11. The LED will stop flashing, then start flashing slowly
12. With the LED flashing slowly, press UNLOCK on the original vehicle remote
13. The Indicators will illuminate for 3 seconds to confirm the process has been completed.

Note: This procedure is used to configure the alarm to the vehicle locking system. If new remotes are required, use the
manufacturer’s information to code new remotes to the car.

Page 1

Page 2 of 8
Ref: VOD/SF/639 Rev 1.0
Date: 04 November 2015 Uncontrolled If Printed or Copied Document Owner: B Scott / N Grove
Key Programming

4 Series
4100-4198-4138 (Remote: 8722-2-Button, 8723-3 Button, 8015-5 Button)
If you have at least one working remote proceed as follows:

1. Disarm the system

2. Open the drivers door and bonnet
3. Switch the ignition ON
4. Press on hold button A until the indicators flash once
5. Enter the PIN code via the button on the emergency override panel
6. The LED on the override panel and the indicators will flash 5 times to confirm the system is in ‘Auto-Learning Mode’
7. Press button A to add the remote, the LED on the override panel will illuminate for approx 1 second and the indicators will
flash once to confirm the remote is added
8. Repeat step 7 for all remotes including previously stored remotes
9. The system automatically exits auto-learning mode after 30 seconds if no further operations are carried out
10. To manually exit auto-learning, close the bonnet

If you do not have any working remotes, proceed as follows:

a. Disarm the system by entering the PIN code

b. Disconnect the alarm power supply
c. Open the drivers door and bonnet
d. Switch the ignition on
e. Reconnect the alarm power supply
f. Enter the PIN code
g. A long flash from the LED on the emergency panel confirms the correct PIN code
h. After 5 seconds the LED on the emergency panel will illuminate show confirm entry into the auto-learning mode
i. Repeat step 7 for all remotes you want to add

Note: A maximum of four remotes can be stored on the alarm system. Adding a new remote will erase all previously stored
remotes.

4435 (Remote: 8772)

1. Disarm the system
2. If possible, remove the antenna from the alarm system
3. Open the drivers door and bonnet
4. Turn the ignition on
5. Enter the PIN code
6. The indicators will flash to confirm entry into Auto-Learning Mode
7. Turn the ignition OFF then ON
8. Enter the PIN code
9. Press button A on the remote or the button on the driver card to add to the system; the LED on the emergency panel will flash
to confirm the remote has been added
10. Repeat step 9 for all remotes/driver cards.
11. Exit auto-learning by closing the bonnet

Note: A maximum of four remotes may be stored on the system. Adding a remote will erase all existing remotes stored
on the system.

Page 2

Page 3 of 8
Ref: VOD/SF/639 Rev 1.0
Date: 04 November 2015 Uncontrolled If Printed or Copied Document Owner: B Scott / N Grove
Key Programming

4 Series (Continued)
4615-4625-4693-4698 (Remote: 8772 or ADR Card: NAV117A)
1. Disarm the system
2. Open the bonnet (siren blue wire to ground, wireless siren only)
3. Open the drivers door
4. Connect main ECU blue wire to ground
5. Turn ignition on
6. Enter PIN code
7. Indicators will flash once to indicate programming mode entered
8. Switch ignition OFF and back ON
9. Indicators will flash twice (table 2 of programming)
10. Enter PIN code again
11. Press button A on the remote to add to the system
12. The LED will give one quick flash to confirm remote added
13. Repeat step 10 for all remotes (remotes not added will be deleted)
14. Exit programming mode by closing the bonnet or removing the main unit blue wire from ground

Note: It may be necessary to cycle the alarm (Arm/Disarm) immediately prior to entering programming mode. A
maximum of four remotes may be stored on the system. Adding a remote will erase all existing remotes stored on the
system. Remember to remove the main unit blue wire from ground on completion.

6 Series
6402-6422 (Remote: 7777)
1. Disarm the alarm with existing remote or touch key
2. Turn ignition ON
3. Touch the touch key onto the receptacle
4. Press and hold both buttons on the remote until the LED between the buttons stops flashing (approx 10 seconds)
5. Press button A twice to add to the system
6. Repeat steps 4 and 5 for all remotes you want to add
7. Switch ignition OFF to exit auto-learning mode.

If you need to add a touch key to the system a Jolly Programmer will be required. A maximum of four remotes may be stored on the
system.

Page 3

Page 4 of 8
Ref: VOD/SF/639 Rev 1.0
Date: 04 November 2015 Uncontrolled If Printed or Copied Document Owner: B Scott / N Grove
Key Programming

7 Series
7908-7928 (Remote: 7777)
1. Disarm the system
2. Turn the ignition ON and OFF 3 times within 7 seconds, the system LED will illuminate
3. When the LED extinguishes switch the ignition ON
4. The LED will flash. Count the number of flashes to correspond with the first digit of the PIN code
5. Switch the ignition OFF then back ON and count the flashes for the second digit of the PIN code
6. Repeat steps 3 and 4 until all four digits of the PIN code have been entered (finishing with the ignition ON)
7. If a touch key is programmed to the system touch it onto the receptacle now and the LED will illuminate. If the touch keys
have been programmed out the LED will illuminate after step 4
8. Press and hold both buttons of the remote until the LED between the buttons stops flashing (approx 10 seconds)
9. Press button A to add to the system (the LED on the dash will extinguish for 1 second to confirm)
10. Repeat steps 7 and 8 for all remotes you want stored on the system (maximum of four)
11. Switch the ignition off to exit auto-learning

Adding a 7 Series Touch Key (937)

1. Enter the PIN code as described above
2. Touch a touch key onto the receptacle (existing or new one)
3. The LED will extinguish to confirm
4. Touch the next touch key onto the receptacle
5. The LED will extinguish to confirm
6. Turn the ignition off to exit programming

7518 (Five Button Remote: 7775)

1. Disarm the system
2. Switch the ignition ON and OFF 3 times within 7 seconds, the LED will illuminate for approx 3 seconds
3. When the LED extinguishes switch the ignition ON and count the flashes of the LED to correspond with the first digit of the PIN
code
4. Turn the ignition OFF and back ON and repeat counting for second digit of PIN code
5. Turn the ignition OFF and back ON and repeat counting for third digit of PIN code
6. Turn the ignition OFF and back ON and repeat counting for forth digit of PIN code
7. Turn the ignition OFF then back ON, then LED will illuminate permanently
8. Press buttons 1 and 4 simultaneously, the LED will extinguish for 1 second to confirm the addition of the remote
9. Repeat step 8 for all remotes you want to store on the system
10. Switch the ignition OFF to exit programming

Note: A working touch key is required for programming. Adding a new remote will erase all old remotes. A maximum of 4 remotes can
be stored to the system.

Page 4
Page 5 of 8
Ref: VOD/SF/639 Rev 1.0
Date: 04 November 2015 Uncontrolled If Printed or Copied Document Owner: B Scott / N Grove
Key Programming

8 Series
8165-8185-8186-8188 (Remote: 7777)
1. Disarm the system
2. Turn the ignition ON and OFF 3 times within 7 seconds, the system LED will illuminate
3. When the LED extinguishes switch the ignition ON
4. The LED will flash. Count the number of flashes to correspond with the first digit of the PIN code
5. Switch the ignition OFF then back ON and count the flashes for the second digit of the PIN code
6. Repeat steps 3 and 4 until all four digits of the PIN code have been entered (finishing with the ignition ON)
7. If a touch key is programmed to the system touch it onto the receptacle now and the LED will illuminate. If the touch keys
have been programmed out the LED will illuminate after step 4
8. Press and hold both buttons of the remote until the LED between the buttons stops flashing (approx 10 seconds)
9. Press button A to add to the system (the LED on the dash will extinguish for 1 second to confirm)
10. Repeat steps 7 and 8 for all remotes you want stored on the system (maximum of four)
11. Switch the ignition off to exit auto-learning

Adding a 8 Series Touch Key (937)

1. Enter the PIN code as described above
2. Touch a touch key onto the receptacle (existing or new one)
3. The LED will extinguish to confirm
4. Touch the next touch key onto the receptacle
5. The LED will extinguish to confirm
6. Turn the ignition off to exit programming

Note: A working touch key is required for programming. Adding a new remote will erase all old remotes. A maximum of 4 remotes can
be stored to the system.

Page 5

Page 6 of 8
Ref: VOD/SF/639 Rev 1.0
Date: 04 November 2015 Uncontrolled If Printed or Copied Document Owner: B Scott / N Grove
Key Programming

G Series
G100-193-198 (Remote: 8772)
1. Disarm the system
2. Open the drivers door and bonnet
3. Switch the ignition ON
4. Press and hold button A on the remote until the indicators flash once
5. Enter the PIN code on the emergency override panel
6. The indicators will confirm by flashing 5 times and the LED will be permanently illuminated
7. Press button A on the remote to add to the system; the LED will extinguish for 1 second and the indicators will flash to confirm
8. Repeat step 7 for all remotes you want to have stored on the system (adding remotes will erase all existing remotes)
9. If the system receives no input for 30 seconds it will exit auto-learning automatically
10. To exit auto-learning close the bonnet

If you do not have any working remotes, proceed as follows:

a. Disarm the system by entering the PIN code

b. Disconnect the alarm power supply
c. Open the drivers door and bonnet
d. Switch the ignition on
e. Reconnect the alarm power supply
f. Enter the PIN code
g. A long flash from the LED on the emergency panel confirms the correct PIN code
h. After 5 seconds the LED on the emergency panel will illuminate show confirm entry into the auto-learning mode
i. Repeat step 7 for all remotes you want to add

G300-368 Procedure for adding new Driver Cards

1. Disarm the system
2. Open the drivers door and bonnet
3. Turn the ignition ON
4. Enter PIN code using the button on the emergency override panel
5. The indicators will flash once and the LED will illuminate to confirm access to the Auto-Learning Mode
6. Enter the PIN code
7. The indicators will flash 5 times and the LED will illuminate permanently to confirm correct PIN code
8. Press the button on the driver card, the indicators will flash once and the LED will extinguish for 1 second to confirm the
addition of the driver card
9. Repeat step 8 for all driver cards you want to store (all existing cards will be erased)
10. If the system receives no input for 30 seconds it will exit auto-learning automatically
11. To exit auto-learning close the bonnet

Remote Central Door Locking

1046 (Remote: 7777)
1. Press button B to unlock the doors
2. Locate the 1046 control unit and set switch ‘2’ to ON
3. Press and hold both buttons of the remote, the LED will flash, when the LED stops flashing release the buttons. The LED will
be permanently illuminated
4. Press the large button to add the remote to the system
5. Repeat steps 3 and 4 for all remotes you want stored on the system
6. When all remotes are added return switch ‘2’to off
7. Test all remotes

Page 6

Page 7 of 8
Ref: VOD/SF/639 Rev 1.0
Date: 04 November 2015 Uncontrolled If Printed or Copied Document Owner: B Scott / N Grove
Key Programming

Immobiliser
8510 (Touch Key: 937)
1. Disarm the system
2. Turn the ignition ON and OFF 3 times, then ON within 7 seconds
3. The LED will illuminate permanently
4. Touch a working touch key onto the receptacle, the LED will extinguish for 1 second
5. Repeat step 3 for the additional keys you want to add
6. Switch the ignition OFF to exit programming

Note: A maximum of 4 touch keys can be stored on the system. Adding keys will erase all existing keys

0802T (Touch Key: 937)

1. Disarm the immobiliser using a working touch key (LED extinguished)
2. Turn the immobiliser switch ‘1’ to the ON position (the LED will illuminate)
3. Touch a new key into the mini-socket for approx 1 second, the LED will flash
4. Repeat step 3 for all the existing touch key
5. Turn the immobiliser switch ‘1’ to the OFF position (the LED will extinguish)
6. Test both keys.

Note: A maximum of 2 keys can be stored on this system. Adding a key will erase the existing key.

Pre-Coded Remote Keys

6019-6019MKII - NO LONGER AVAILABLE

The 6019 uses a pre-coded 6657 (418 MHz) remote.
These can be ordered from Cobra; please supply the code from circuit board of the original remote or on the CPU (9 digits
OR 9 digits + G).
832-832SU
The 832 uses a pre-coded 6657 (433 MHz) remote.
These can be ordered from Cobra; please supply the code from circuit board of the original remote or on the CPU
(9 digits + E).

5801
The 5801 uses a pre-coded 5557 remote.
These can be ordered from Cobra; please supply the code from the circuit board of the original remote or on the CPU (4
digits OR 1 letter+5 digits OR 2 letters+5 digits + G)

Page 7

Page 8 of 8
Ref: VOD/SF/639 Rev 1.0
Date: 04 November 2015 Uncontrolled If Printed or Copied Document Owner: B Scott / N Grove