KF12

Portable powered floor monitor

and PA system
DATASHEET
Features:
• Unique performance-to-size ratio
• Self powered + Auxiliary powered output
• Integrated DSP and remote control
• Symmetrical horizontal and vertical coverage
• Cabinet angled for floor monitor use
• Integrated 35mm pole adapter
• Integrated flying and stacking hardware
• Top quality components for outstanding
performance
• Top quality components for outstanding
performance
• For use in single, point source applications,
as a floor monitor and in combination with
other K-array systems

Applications:
• Small and medium scale events
• Theatres, concert halls, conferences,
churches

The K-array KF12 is a self-powered, 2-way speaker system. The KF12 uses a 12” neodymium speaker with a 3” voice coil
Its ultra-compact enclosure has an incredible reserve of for low-mid frequencies. The mid-high frequency section uses
power that delivers 127 dB continuous sound pressure with a co-axially mounted 3” voice coil neodymium compression
consistent 700 horizontal and vertical coverage. driver.
An internal DSP module provides 16 control presets.
The KF12 is best suited as a floor monitor and for medium Dedicated remote control software allows for control of the
throw applications in theatres, concert halls, churches and for speaker from a PC.
corporate AV events. The integrated 35mm pole mount and
the second amplifier output are specifically designed for use All the KF12 components are designed by the
with the K-array KL 18 passive sub. This combination extends K-array R&D department and custom made under
the system frequency response down to 30 Hz. the K-array quality control system.

www.k-array.com
HP Sound Equipment s.r.l. Viale Roma 7/i - 50037 - San Piero a Sieve (FI), Italy
tel. +39 055 8487222 - fax. +39 055 8487238 - e-mail: [email protected]
 KF12 DISPERSION GRAPHS
Acoustics 8 KHz
Speakers power handling 800 w + 200 W (AES) 4 KHz
1 KHz left
Max power 1200 x 500 W 1
500 Hz
top
90°
Impedance 8Ω + 8Ω 250 Hz 120° 60°

Frequency range 60 Hz - 19 KHz.

150° 30°
SPL 1W/ 1mt 97 dB (low) 101 dB (high) 2

Maximum SPL 127 dB continuous - 133 dB peak

back front
back 180° 0° front
Coverage
Horizontal 70°
-150° -30°
Vertical 70°

Crossover -120°
-90°
-60°

front
Type DSP controlled botton

Frequency 1.2 KHz horizontal

Transducers
Low - Mid frequency 1 x 12” Neodymium speakers with 3” voice coil
1 x 1” Neodymium coaxial compression drivers with
High frequency left
3” voice coil top
90°
120° 60°
Audio Input
Connectors male + female parallel 3-pin balanced XLR 150° 30°

Wiring Pin1 = ground / Pin2 = hot (+) / Pin3 = cold (-)

Power Audio Output back

back 180°
front
0° front

Connector 1 x 4-pin speakon

Remote control Input -150° -30°

Connectors 1 x female 8-pin RJ45

-120° -60°
-90°
Power Input front
botton

Connectors 2 x PowerCon IN/OUT

Amplifiers vertical
Type 1 modules class D - DSP controlled

Power 1000 W x 2 channel (2000 watt total) 3

Protection Dynamic limiter, over current, over temp, short circuits

AC power
210 - 240 Vac 50Hz (default)
Operating range
100 - 120 Vac 60Hz (selectable)
I.nom 5.5 A / 115 Vac - 3.6 A / 230 Vac

Minimum operation voltage 95 Vac - 195 Vac

Notes for data
Maximum operation voltage 125 Vac - 205 Vac 1. Maximum RMS applicable power for a musical signal, the
reference signal is the one proposed by EIAJ standard.
Default 12A(>10 sec) - 24A (<1 sec) 2. Measured @4 mt then scaled @1 mt
Max continuous and burst current 3. Amplifier wattage rating is based on the maximum
Selectable 20A(>10 sec) - 40A (<1sec)
unclipped burst sine wavwwe RMS voltage that the
Physical amplifier will produce into the nominal load impedance.

Dimensions 32.5 x 33.5 x 33.8 cm (12.91” x 13.19” x 13.31”) New materials and design are introduced into existing
products without previous notice. Present systems may
Weight 11.8 Kg (26.01 lbs) differ in some respects from those presented in this
brochure.