CAT-1577E CAT-1577E

CAT-1577E
 (D83)D89
D75

CF I 23 CF…W I39 CF…G I47 NUCF I 59 （R）NAST (I85)I86 NURT I97

CFKR I 29 CF-RU1 I43 CF…/SG I49 CR I 61
NART I89 CRY I99
CFES I 33 CF-FU1 I43 CFS I53 CRH I 69
CFE I 35 CF-SFU I45 CFS…W I57 CL I 22 NART…/SG I95

CRBH(V) CRBF(V)
 Gifu factory main entrance

Assembling process in a clean room

 CAT-1577E

The Needle Roller Bearing Series are manufactured through a control system that alleviates
their impact on the global environment to meet the quality requirements of ISO 14001 in
compliance with the quality requirements level of ISO 9001 for quality improvement.

This catalog adopts the SI system (system of international units) in conformance

with ISO (International Organization for Standardization) Standard 1000.

In the table of dimensions, standard products are referred to using identification numbers marked with .
The products are reputed for high quality, reasonable price and quick delivery. The identification numbers marked
with refer to our semi-standard products.
The specifications and dimensions of products in this catalogue are subject to change without prior notice.

1
 A

General Explanation Description of Each Series & Table of Dimensions C

Characteristics of Needle Roller Bearings A 3 Shell Type Needle Roller Bearings TA・TLA・BA・BHA B 1
Types and Features of Bearings A 5 Needle Roller Cages for general usage KT・KT…N C 1
D
Outline of Bearing Selection A 16 Needle Roller Cages for engine connecting rods KT…EG・KTV…EG C 17
Basic Dynamic Load Rating and Life A 17 Machined Type Needle Roller Bearings NA・TAFI・TRI・BRI D 1
Basic Static Load Rating and Static Safety Factor A 21 C-Lube Machined Type Needle Roller Bearings TAF…/SG D75 E
Calculation of Bearing Loads A 22 Needle Roller Bearings with separable cage NAF D 77
Boundary Dimensions and Identification Number A 26 Roller Bearings NAG・NAU・TRU・NAS E 1
Accuracy A 30 Thrust Bearings NTB・AS・AZK・WS・GS F 1
F
Clearance A 37 Combined Type Needle Roller Bearings NAX・NBX・NATA・NATB G 1
Fit A 39 Inner Rings IRT・IRB・LRT・LRB H 1
G
Design of Shaft and Housing A 44 Cam Followers CF・CFKR・CFS・NUCF・CR I 1
Lubrication A 49 C-Lube Cam Followers CF…/SG I49
Friction and Allowable Rotational Speed A 56 Roller Followers NAST・NART・NURT・CRY I77 H
Operating Temperature Range A 57 C-Lube Roller Followers NART…/SG I95
Handling of Bearings A 57 Crossed Roller Bearings CRBH(V)・CRBC・CRB・CRBT・CRBS・CRBF(V) J 1
Spherical Bushings SB・GE・SBB K 1 I
Pilloballs PB・PHS・POS・PHSA K 29
LHSA・LHS
L-balls

Super Flexible Nozzles SNA・SNM・SNPT

K45
K55
J
Parts For Needle Roller Bearings OS・DS・WR・AR・Needle Roller L 1

L
Presentation of Linear Motion Rolling Guide and Mechatronics Series M47

M
Alphabetical Index M61

2 3
 Nippon Thompson Co., Ltd. is a bearing
manufacturer that launched the technical
development of needle roller bearings for the
first time in Japan and is proud of the high
quality level and abundant varieties of its
products.
Needle roller bearings are bearings for
rotary motion that incorporate needle-
shaped thin rollers instead of ordinary
bearing balls or rollers. Compared with
other rolling bearings, they are small-sized
and lightweight but have a large load
capacity. They are widely used with high
reliability in the fields of automobiles,
industrial machinery, OA equipment, etc. as
resource-saving type bearings that make the
whole machine compact.

A1 A2
 A
Characteristics
Characteristics
of Needle
of Needle
RollerRoller
Bearings
Bearings
Bearings can
Bearings
be classified
can be classified
into two main
into two
types,
main
namely
types,rolling
namelybearings
rolling and
bearings
sliding
and
bearings.
sliding bearings.
Rolling bearings
Rolling bearings
can be subdivided
can be subdivided
Needle Roller
further intofurther
NeedleBearings
Roller are
ball bearings
Bearings
into ball and
high-precision
bearings
roller and
are high-precision
bearings
rolling bearings
roller according
rolling with
bearings according
bearings
a lowwith
to the rolling
sectional
to the
a low height,
sectional
elements.
rolling elements.
incorporating
height, incorporating
needle needle
Classification
Classification
of bearings
of bearings B
rollers as rollers
the rolling
as the
element.
rollingThey
element.
haveThey
the following
have the features.
following features.

Deep grooveDeep
ball bearings
groove ball bearings C
MeritsMerits
of Rolling
of Rolling
Bearings
Bearings Merits Merits
of Needle
of Needle
Roller Bearings
Roller Bearings Radial ball
Angular contact
Radial ball
Angular
ball contact
bearingsball bearings
bearingsbearings Self-aligningSelf-aligning
ball bearingsball bearings
ComparedCompared
with sliding
withbearings,
sliding bearings,
rolling bearings
rolling bearings
ComparedCompared
with otherwith
rolling
other
bearings,
rolling bearings,
Needle Needle
D

Ball bearings

Ball bearings
have the following
have the merits:
following merits: Roller Bearings
Roller have
Bearings
the following
have the advantages:
following advantages: Others Others

Thrust ball bearings

Thrust ball
with
bearings
flat backwith
faceflat back face
Static and
Static
kinetic
andfriction
kinetic is
friction
low. is low.
With a low
With
withstand
sectional
a low sectional
withstand
height, they
heavy loads.
height,
heavy loads.
canthey can
Thrust ball bearings
Thrust ball
with
bearings
aligningwith
seataligning
washerseat washer
E
Thrust ball
Thrust ball
Since theSince difference
the difference
between between
static friction
static and Since they
friction and Since
havethey
a low
havesectional
a low sectional
height compared
height compared bearingsbearings Double-direction
Double-direction
angular contact
angular
thrust
contact
ball bearings
thrust ball bearings
kinetic friction
kinetic
is small
frictionand
is small
the frictional
and the coefficient
frictional coefficient
is with
is otherwith
rolling
other
bearings
rolling bearings
and yet can
and withstand
yet can withstand

F
also small, also
drive
small,
unitsdrive
or machines
units or machines
can be made can be made heavy loads,
heavy
machines
loads, machines
can be madecan be
more
madecompact
more compact

Rolling bearings

Rolling bearings
Others Others
more compactmoreandcompact
lightweight,
and lightweight,
saving machine
savingcosts
machine costsand lightweight,
and lightweight,
thus savingthus
costs.
saving costs.

Bearings

Bearings
and powerand consumption.
power consumption.
Needle rollerNeedle
bearings
roller bearings

Stable accuracy
Stable accuracy
for longfor
periods.
can be maintained
long periods.
can be maintained RotatingRotating
torque istorque
mechanical
mechanical
small,isimproving
efficiency.
small, improving
efficiency.
Cylindrical roller
Cylindrical
bearings
roller bearings G
Radial roller
Radial roller
Tapered roller
Tapered
bearings
roller bearings
bearingsbearings
Owing toOwing
less wear,
to lessstable
wear, accuracy can be can Since
stable accuracy be the Since
rotating
theradius
rotating
is small,
radiusthe
is small,
rotating
thetorque
rotating torque

Roller bearings

Roller bearings
maintained
maintained
for long periods.
for long periods. is also small
is also
under
smalltheunder
samethefrictional
same conditions,
frictional conditions, Self-aligningSelf-aligning
roller bearings
roller bearings
thus improving
thus improving
mechanical mechanical
efficiency.efficiency.
Others Others H
MachineMachine
reliability
reliability
is improved.
is improved. Inertia isInertia
minimized.
is minimized. Thrust needle
Thrust
rollerneedle
bearings
roller bearings

Since theSince
bearingthelife
bearing
can be lifeestimated
can be estimated
based onbased Since
on the Since
bearingthevolume
bearingand volume
weightandareweight
small,are
thesmall, the Thrust roller
Thrust cylindrical
Thrust roller
Thrustroller
cylindrical
bearings
roller bearings I
rolling fatigue,
rolling
machine
fatigue,reliability
machine is reliability
improved.is improved. moment ofmoment
inertia of
of the
inertia
bearing
of theisbearing
minimized
is minimized
when it when it bearingsbearings Thrust tapered
is put in motion.
is put in motion. Thrust
roller
tapered
bearings
roller bearings

J
Others Others

Sliding bearings

Sliding bearings
Lubrication
Lubrication
is simplified.
is simplified. Most suited
Mosttosuited
oscillating
to oscillating
motions.motions.

Since grease
Sincelubrication
grease lubrication
is sufficient
is sufficient
in most cases,
in most cases,
Many rolling
Manyelements
rolling elements
are arranged
are arranged
at a small at a small
lubricationlubrication
can be simplified
can be simplified
for easy maintenance.
for easy maintenance.spacing pitch,
spacing
andpitch,
this configuration
oscillatingoscillating
and this configuration
motions. motions.
is most suited
is most
to suited to
Metals, bushings,
Metals, others
bushings, others
K

A3 A4
TypesTypes
and Features
and Features
of Bearings
of Bearings A
Bearings can
Bearings
be roughly
can beclassified
roughly into
classified
radial into
bearings
radialand
bearings
thrust and
bearings
thrustaccording
bearings according
to applicable
to applicable
load direction.
load direction. Crossed Roller
Crossed
Bearings
Roller are
Bearings
special are
shape
special
bearings
shape that
bearings
can simultaneously
that can simultaneously
receive loads
receive
in allloads
directions
in all directions
with a with a
Radial Bearings
Radial are
Bearings
grouped
areinto
grouped
Shell into
TypeShell
NeedleTypeRoller
Needle
Bearings,
Roller Bearings,
Machined Machined
Type Needle Type
Roller
Needle
Bearings,
Roller Bearings,
and and single bearing.
single bearing.
various other
various
types.
Follower Bearings
other
Thrust
Follower that
types.
Bearings
Bearings
are used
Thrustare
that for
Bearings
arecam
groupedareinto
usedmechanisms
grouped
Thrustinto
for cam mechanisms
Needle
Thrust
and linear and
Roller
motion
Needle
linear
Bearings
Rollerand
aremotion
grouped
Bearings
Thrustand
areinto
grouped
Roller
Thrust
Bearings.
Cam Followers
Roller Bearings.
into Cam Followers
and Rollerand Roller
Bearings other
Bearings
axial loadsaxial
thanother
andloads
rolling
PILLOBALLs
than
bearings,
rolling bearings,
and PILLOBALLs
such as self-aligning
and L-Ballsand
that
such as self-aligning
L-Balls
are used
that for
Spherical Spherical
arelink
used
Bushings Bushings
mechanisms,
that can support
for link mechanisms,
that canradial
are also available.
support
are also available.
loadsradial
andloads and
B
Followers.Followers.

Classification
Classification
of ofBearings
Bearings C
TA、TAM TA、TAM
TLA、TLAM
TLA、TLAM

D
BA、BAMBA、BAM
Shell Type Shell Type BHA、BHAM
BHA、BHAM
Needle Roller
Needle
Bearings
Roller Bearings
YT YT
YTL YTL
YB
YBH
YB
YBH
E
KT、KT…N
KT、KT…N
Needle RollerNeedle
Cages for
Roller
General
CagesUsage
for General Usage

F
KTW KTW
Needle Roller
Needle
Cages
Roller Cages
Radial Bearings

Radial Bearings

KT…EG KT…EG
Needle RollerNeedle
Cages for
Roller
Engine
Cages
Connecting
for EngineRods
Connecting Rods
KTV…EG KTV…EG

NA、RNANA、RNA
TAFI、TAF
TAFI、TAF
G
TRI、TR TRI、TR
BRI、BR BRI、BR

H
Machined Type
Machined Type
Needle Roller
Needle
Bearings
Roller Bearings GTRI、GTR
GTRI、GTR
High Rigidity Type
High Crossed
Rigidity Type
RollerCrossed
Bearings
Roller CRBH(V) CRBH(V)
(V) Bearings (V)
C-Lube Machined
C-Lube
TypeMachined
Needle Roller
Type Needle
Bearings TAF… /SGTAF… /SG
Roller Bearings
NAF、RNAF
NAF、RNAF
Needle RollerNeedle
Bearings
Roller
with Bearings
Separablewith
CageSeparable Cage
NAFW、RNAFW
NAFW、RNAFW
I
NAU NAU Mounting Holed
Mounting
Type High
Holed
Rigidity
Type High Rigidity
Crossed RollerCrossed
Bearings
Roller
(V) Bearings (V) CRBF(V) CRBF(V)
NAG NAG
Roller Bearings
Roller Bearings

J
TRU TRU
Roller Bearings
Roller
for Sheaves
Bearings for Sheaves NAS NAS

Thrust Needle
Thrust
Roller
Needle
Bearings
Roller Bearings NTB NTB
Bearings

Bearings
Thrust

Thrust

Thrust Roller
Thrust
Bearings
Roller Bearings AZK、AZ AZK、AZ K
with Thrust Ball
withBearing
Thrust Ball Bearing NAXI、NAX
NAXI、NAX
Combined Type

Combined Type

L
Bearings

Bearings

Combined Type
Combined Type with Thrust Roller
with Bearing
Thrust Roller Bearing NBXI、NBX
NBXI、NBX
Needle Roller
Needle
Bearings
Roller Bearings with Angular Contact
with Angular
Ball Bearing
Contact Ball Bearing NATA NATA
with Three-point
withContact
Three-point
Ball Bearing
Contact Ball Bearing NATB NATB

A5 A6
 A

Shell Type
Shell
Needle
Type Needle
Roller Bearings
Roller Bearings Machined
Machined
Type Needle
Type Needle
Roller Bearings
Roller Bearings B
Shell Type Shell
NeedleTypeRoller
NeedleBearings
Rollerare
Bearings
lightweight
are lightweight
with with Machined Type
Machined
NeedleTypeRoller
Needle
Bearings
Roller have
Bearings
an outer
have an outer
the lowest sectional
the lowestheight
sectional
among height
needle
amongroller
needle
bearings
roller bearings ring made ring
by machining,
made by machining,
heat treatment,
heat treatment,
and grinding.
and grinding.
with outer ring,
with outer
because ring,they
because
employ they
a shell
employtypea outer
shell type outer The outer ring
The has
outerstable
ring has
highstable
rigidityhigh
andrigidity
can beand
easily
can be easily
ring madering frommade
accurately drawn,
accurately
a thinfrom
carburized
special-steel
a thin special-steel
drawn, carburized
and quenched.
plate which
and quenched.
plate
is which is used even for
used
These bearings
light
even
These are
alloy
forhousings.
light alloy housings.
bearings
available
are inavailable
various intypes
various
and types and C
Since these Since
bearings
theseare bearings
press-fitted
are press-fitted
into the housing,
into the housing, optimally selectable
optimally selectable
for different for conditions
different conditions
such as such as
no axial positioning
no axial positioning
fixtures arefixtures
required.
areThey
required.
are ideal
They are ideal heavy loads,
heavy
high-speed
loads, high-speed
rotation androtation
low-speed
and rotation.
low-speed rotation.
for use in mass-produced
for use in mass-produced
articles thatarticles
requirethat
economy.
require economy. They are most
Theysuitable
are mostfor suitable
general-purpose
for general-purpose
applications.
applications.
D
Radial Bearings
Radial Bearings
Page B1 Page B1 Radial Bearing
Radial Bearing
Page D1 Page D1

E
Needle Needle
Roller Cages
Roller for
Cages
General
for General
Usage Usage Needle Needle
Roller Bearings
Roller Bearings
with Separable
with Separable
Cage Cage
Needle Roller
NeedleCagesRoller
for Cages
GeneralforUsage
General
areUsage
bearings
are bearings In Needle In Roller
NeedleBearings
Roller with
Bearings
Separable
with Separable
Cage, the Cage, the F
that display
thatexcellent
display rotational
excellent performance.
rotational performance.
Their Their inner ring,inner
outerring,
ring outer
and Needle
ring andRoller
NeedleCage Roller
are Cage are
specially shaped
speciallycages
shapedwithcages
high rigidity
with high
andrigidity
accuracy,
and accuracy, combined, combined,
and they can andbethey
separated
can be easily.
separated
Thiseasily.
type This type
precisely guide
precisely
the needle
guide the
rollers.
needle rollers. has a simplehasstructure
a simplewith
structure
high accuracy.
with high accuracy.
In addition,In addition,
Since needle
Sincerollers
needle
variations variations
withrollers
in diameterin are
extremely
diameter
with small
extremely
incorporated
dimensional
are incorporated
small dimensional
and retained,
and retained,
the radial clearance
an assembly
the radial can
clearance
ancombination.
be freely
assembly combination.
canselected
be freelybyselected
choosingby choosing
G
Needle Roller
NeedleCagesRoller
for Cages
GeneralforUsage
General
are Usage
useful are
in useful in These bearings
Thesehave
bearings
excellent
haverotational
excellent performance,
rotational performance,
small spaces
smallwhen
spaces
combined
when with
combined
shaftswith
and shafts
housing
and housing because Needle
because
Roller
Needle
CagesRoller
are used.
Cages are used.
bores that bores
are heatthat treated
are heatandtreated
accurately
and accurately
ground as ground as
raceway surfaces.
raceway surfaces.
H
Radial Bearing
Radial Bearing
Page C1 Page C1 Radial Bearing
Radial Bearing
Page D79 Page D79

I
Needle Needle
Roller Cages
Roller for
Cages
Engine
for Engine
Connecting
Connecting
Rods Rods Roller Bearings
Roller Bearings

J
Needle Roller
Needle
GagesRoller
for Gages
Engine for
Connecting
Engine Connecting
Rods are Rods are Roller Bearings,
Roller Bearings,
in which rollers
in whichare rollers
incorporated
are incorporated
in in
used for motor
used cycles,
for motorsmall
cycles,
motorsmall
vehicles,
motoroutboard
vehicles, outboard double rows,double
are non-separable
rows, are non-separable
heavy-dutyheavy-duty
bearings. bearings.
marines, snow
marines,
mobiles,
snowgeneral-purpose
mobiles, general-purpose
engines, high-
engines, high- They can withstand
They can notwithstand
only radial
not only
loadsradial
but axial
loadsloads
but axial loads
speed compressors,
speed compressors,
etc. that are
etc. operated
that are under
operated under as well, which
as well,
are supported
which are at
supported
the contacts
at the
between
contactsthebetween the
extremely severe
extremely
andsevere
complexandoperating
complexconditions
operating such
conditions such shoulders ofshoulders
inner andof outer
inner rings
and outer
and the
ringsend
andfaces
the of
end faces of
as heavy shock
as heavy
and stringent
loads,
shock
andlubrication.
highloads,
speeds,
stringent lubrication.
high
high
speeds,
temperatures,
high temperatures, rollers. Therefore,
rollers. Therefore,
fixing side of
fixing
they are most
a shaft.
theysuitable
side of a shaft.
are most forsuitable
use at the
for use at the
K
Needle Roller
Needle
CagesRoller
for Cages
Engine for
Connecting
Engine Connecting
Rods are Rods are
lightweight lightweight
and have high
and load
have ratings
high load
andratings
high rigidity
and high rigidity
as well as superior
as well as
wear
superior
resistance.
wear resistance.

Radial Bearing
Radial Bearing
Page C17 Page C17 Radial Bearing
Radial Bearing
Page E1 Page E1
L

A7 A8
 A

Thrust Thrust
Bearings
Bearings Cam Followers
Cam Followers B
Thrust Bearings
Thrust consist
Bearingsofconsist
a precisely
of a made
precisely
cage
made
and cage and Cam Followers
Cam Followers
are bearings are with
bearings
a studwithincorporating
a stud incorporating
rollers, and
rollers,
can receive
and canaxial
receive
loads.
axialThey
loads.
haveThey
highhave high needle rollers
needle
in arollers
thick walled
in a thick
outer
walled
ring.outer ring.
rigidity and
rigidity
high and
load high
capacities
load capacities
and can be andused
can in
be used in They are designed
They are designed
for outer ring
for outer
rotation,
ringandrotation,
the outer
and the outer
small spaces.
small spaces.
Thrust Needle
ThrustRoller
Needle
Bearings
Roller use
Bearings
needle use
rollers,
needlewhile
rollers, while
rings run directly
rings run
Various types
Various
ondirectly
of Cam
matingon cam
typesFollowers
mating
guidecam
of Cam Followers
surfaces.
guide surfaces.
are available.
are available.
They are They are C
Thrust Roller
Thrust
Bearings
Roller use
Bearings
cylindrical
use cylindrical
rollers. rollers. widely usedwidely
as follower
used asbearings
follower for
bearings
cam mechanisms
for cam mechanisms
and for linear
andmotions.
for linear motions.

D
Thrust Bearing
Thrust Bearing
Page F1 Page F1 Follower Follower
Bearing Bearing
Page I1 Page I1

E
Combined
Combined
Type Needle
Type Needle
Roller Bearings
Roller Bearings Roller Followers
Roller Followers
Combined Combined
Type NeedleType Needle
Roller Bearings
Roller Bearings
are are Roller Followers
Roller Followers
are bearingsare inbearings
which needle
in which
rollers
needlearerollers are F
combinations
combinations
of a radialofbearing
a radialand
bearing
a thrust
and bearing.
a thrust bearing. incorporated
incorporated
in a thick walled
in a thick
outer
walled
ring.outer ring.
Caged Needle
Caged Roller
NeedleBearings
Roller Bearings
are usedareas used
radial as radial These bearings
These arebearings
designed
are for
designed
outer ring
for outer
rotation,
ringand
rotation, and
bearings bearings
and ThrustandBallThrust
Bearings
Ball Bearings
or Thrust orRoller
Thrust Roller the outer rings
the outer
run directly
rings run
ondirectly
mating on
cammating
guidecam
surfaces.
guide surfaces.
Bearings are
Bearings
They can They
used as
arethrust
be subjected
usedbearings.
as thrust bearings.
can be subjected
to radial loads
to radial
andloads
axial and
loadsaxial loads
They are used
They as
and for linear
arefollower
andmotions.
used asbearings
followerfor
for linear motions.
bearings
cam mechanisms
for cam mechanisms
G
simultaneously.
simultaneously.

H
Combined
Combined
Type Bearing
Type Bearing
Page G1 Page G1 Follower Follower
Bearing Bearing
Page I77 Page I77

I
Inner Rings
Inner Rings Crossed
Crossed
Roller Bearings
Roller Bearings

J
Inner Rings
Inner
are Rings
heat-treated
are heat-treated
and finished
andbyfinished
grinding
bytogrinding to Crossed Roller
Crossed Bearings
Roller Bearings
are high-rigidity
are high-rigidity
and compact and compact
a high degree
a highofdegree
accuracy
of accuracy
and are used
and arefor used
Needlefor Needle bearings with
bearings
their with
cylindrical
their cylindrical
rollers alternately
rollers alternately
crossed crossed
Roller Bearings.
Roller Bearings. at right angles
at right
to angles
each other
to each
between
other inner
betweenand inner
outerand outer
In the case
In the
of Needle
case ofRoller
Needle Bearings,
Roller Bearings,
normally normally
the the rings. A single
rings. Crossed
A single Roller
CrossedBearing
Rollercan
Bearing
take loads
can take loads
shafts areshafts
heat-treated
are heat-treated
and finished
and byfinished
grinding
by and
grinding and from any from
directions
any directions
at the sameat thetimesame
suchtime
as radial,
such as radial,

K
used as used
racewayas raceway
surfaces. surfaces.
However, However,
when it whenis it is thrust, andthrust,
momentandloads.
moment loads.
impossibleimpossible
to make to shaft
makesurfaces
shaft surfaces
accordingaccording
to the to the These bearings
These are
bearings
widelyareused
widely
in the used
rotating
in theparts
rotating
of parts of
specified surface
specifiedhardness
surface hardness
or surfaceorroughness,
surface roughness,
Inner Inner industrial robots,
industrial
machine
robots, tools,
machine
medical
tools,equipment,
medical equipment,
etc. etc.
Rings are Rings
used. are used. which require
which compactness,
require compactness,
high rigidityhigh and
rigidity
highand high
rotational accuracy.
rotational accuracy.

Component
Component
part part
Page H1 Page H1 Crossed Roller
CrossedBearing
Roller Bearing
Page J1 Page J1
L

A9 A10
 A

Spherical
Spherical
Bushings
Bushings Seals for
Seals
Needle
for Needle
Roller Bearings
Roller Bearings B
Spherical Spherical
Bushings Bushings
are self-aligning
are self-aligning
spherical spherical
plain plain Seals for Seals
NeedleforRoller
NeedleBearings
Roller Bearings
have a low have
sectional
a low sectional
bushings, bushings,
which have whichinner
have andinner
outerandrings outerwithrings with height and height
consist
andofconsist
a sheet of metal
a sheet
ringmetal
and ring
special
and special
spherical sliding
spherical surfaces.
sliding surfaces.
They can They
take acan large
takeradial
a large radial synthetic rubber.
synthetic rubber.
load and aload
They areThey
bi-directional
and a bi-directional
divided
are into
axial load axial
divided
at theload
steel-on-steel
same at time.
into steel-on-steel
the same time.
types thattypes are that are
As these seals
As these
height as height
are seals
manufactured
NeedleasRoller
Needle
are manufactured
Bearings,
to the same
Roller Bearings,
to the
sectional
grease leakage
same sectional
greaseand
leakage and C
suitable forsuitable
applications
for applications
where therewhere
are there
alternate
are loads
alternate loads the penetration
the penetration
of foreignofparticles
foreign can
particles
be effectively
can be effectively
or shock orloads,shockandloads,
maintenance-free
and maintenance-free
types which types which preventedprevented
by fitting bythem
fitting
directly
them todirectly
the sides
to theof sides of
require norequire
lubrication.
no lubrication. combinable combinable
bearings. bearings.
D
SphericalSpherical
Sliding Bearing
Sliding Bearing
Page K1 Page K1 Component
Component
Part Part
Page L1 Page L1

E
PILLOBALLs
PILLOBALLs Cir-clips
Cir-clips
for Needle
for Needle
Roller Bearings
Roller Bearings
PILLOBALLsPILLOBALLs
are compact are self-aligning
compact self-aligning
spherical spherical
plain plain Cir-clips for
Cir-clips
Needlefor Roller
Needle
Bearings
Roller have
Bearings
beenhave
specially
been specially F
bushings which
bushings canwhich
supportcana support
large radial
a large
loadradial
and aloadbi- and a bi- designed designed
for needleforroller
needle
bearings
roller on
bearings
which,on in which,
many in many
directionaldirectional
axial load axial
at theload
same at the
time.same time. cases, generally
cases, generally
available available
Cir-clips cannot
Cir-clipsbecannot
used. be used.
PILLOBALL PILLOBALL
Rod EndsRod haveEnds
eitherhave
a female
eitherthread
a femalein the
thread in the They haveTheya lowhave
sectional
a low height
sectional
andheight
are very
andrigid.
are very rigid.
body or a body
male or
assembledassembled
thread
a male
onto machines.
on thread
the body,
onto machines.
on so
thethey
body,can
sobethey
easily
can be easily There are There
Cir-clips
used for positioning
arefor
Cir-clips
shafts for
used for positioning
andshafts
for bores,
to preventtobearing
and for
andbores,
preventmovement
they are
and they are
bearing movement
in the in the G
PILLOBALLs PILLOBALLs
are used in are
control
used and
in control
link mechanisms
and link mechanisms
in in axial direction.
axial direction.
machine tools,
machine textile
tools,
machines,
textile machines,
packagingpackaging
machines,machines,
etc. etc.

H
SphericalSpherical
Sliding Bearing
Sliding Bearing
Page K29Page K29 Component
Component
Part Part L17Page L17
Page

I
L-BallsL-Balls NeedleNeedle
RollersRollers

J
L-Balls areL-Balls
self-aligning
are self-aligning
rod-ends consisting
rod-ends consisting
of a special of a special Needle Rollers
Needleare Rollers
used are
for needle
used for
roller
needle
bearings
roller and
bearings and
zinc die-cast
zincalloy
die-cast
bodyalloy
and body
a studded
and aball
studded
whichball
haswhich
its has its are rigid and
arehighly
rigid and
accurate.
highly accurate.
axis at right-angles
axis at right-angles
to the body. to the body. These needle
These rollers
needle
arerollers
widelyare
used
widely
as rolling
used elements
as rolling elements
They can They
performcantilting
perform
movement
tilting movement
and rotation
andwith
rotation
low with low for bearings,
for and
bearings,
also as
andpins
also
and
asshafts.
pins and shafts.
torque, andtorque,
transmit
andpower
transmitsmoothly
power due
smoothly
to thedue
uniform
to the uniform

K
clearance clearance
between the between
slidingthesurfaces.
sliding surfaces.
They are Theyused are
in link
usedmechanisms
in link mechanisms
in automobiles,
in automobiles,
construction
construction
machinery,machinery,
farm and farm packaging
and packaging
machines,machines,
etc. etc.

SphericalSpherical
Sliding Bearing
Sliding Bearing
Page K45Page K45 Component
Component
Part Part L23Page L23
Page
L

A11 A12
 A
Features
Features
of of
Bearings
Bearings
Bearing series
Bearing series Direction of
AppearanceAppearance Direction
Load direction
of LoadAllowable
direction Allowable
Friction Sectional Sectional
Friction Reference Reference Bearing series
Bearing series Direction of
AppearanceAppearance Direction
Load direction
of LoadAllowable
direction Allowable
Friction Sectional Sectional
Friction Reference Reference

B
motion and
motion
capacity and
rotational
capacityspeedrotational speed height height
page page motion and
motion
capacity and
rotational
capacityspeedrotational speed height height
page page

Needle rollerNeedle roller

Caged type Caged type bearings bearings
Shell Type Shell Type

C
Thrust Thrust
Needle Roller
Needle Roller B1∼ B1∼ Bearings Bearings F1∼ F1∼
Bearings Bearings
Full Full
complementcomplement Roller Roller
type type bearings bearings

With With
D
For For
general usage
general usage C1∼ C1∼ thrust thrust
ball bearing ball bearing
Needle Needle
Roller Cages
Roller Cages
For engine For engine With With
E
connecting connecting C17∼ C17∼ thrust thrust
rods rods roller bearingroller bearing
Combined Type
Combined Type
Needle Roller
Needle Roller G1∼ G1∼

Caged type Caged type

Bearings Bearings
With
angular
With
angular
F
contact contact
ball bearing ball bearing
Machined Type
Machined Type
Needle Roller
Needle Roller D1∼ D1∼

G
Bearings Bearings
With With
Full Full three-point three-point
complementcomplement contact contact
type type ball bearing ball bearing

Needle Roller
Needle Roller
Bearings with
BearingsCaged
Separable Cage
with type Caged type
Separable Cage
D79∼ D79∼ Caged type Caged type H
Cam Followers
Cam Followers I1∼ I1∼

Caged type Caged type

Full Full
complementcomplement
type type
I

J
Full Full
Roller Bearings
Roller Bearings Separable Separable
complementcomplement E1∼ E1∼ caged type caged type
type type

K
Non-separable
Non-separable
For sheavesFor sheaves Roller Followers
Roller Followers
caged type caged type I77∼ I77∼

Oscillating Oscillating
Radial Radial
Axial Light
Axial Medium
Light Medium
Heavy Especially
Heavy Especially Non-separable
Non-separable
Symbol Symbol
Rotation Rotation Excellent Excellent
Normal Normal

L
motion motion
load load
load loadload load
load load
load excellent
load excellent full full
complementcomplement
type type

A13 A14
 A
Features
Features
of of
Bearings
Bearings Outline
Outline
of Bearing
of Bearing
Selection
Selection
Bearings are Bearings
availableare inavailable
many types
in many
and types
sizes.andTo sizes.
obtain To
satisfactory
obtain satisfactory
bearing performance
bearing performance
in machinesin machines
and and
Direction of Direction
Load direction
of LoadAllowable
direction Allowable Sectional Sectional
Reference Reference
Bearing series
Bearing series AppearanceAppearance Friction Friction equipment,equipment,
it is essential
it istoessential
select the
to select
most suitable
the mostbearing
suitablebybearing
carefullybystudying
carefullythe
studying
requirements
the requirements
for the application.
for the application.
B
motion and
motion
capacity and
rotational
capacityspeedrotational speed height height
page page
Although there
Althoughis nothere
particular
is no procedure
particular procedure
or rule for or
bearing
rule for
selection,
bearing an
selection,
example anofexample
a commonly
of a commonly
adopted procedure
adopted procedure
is shown inisthe
shownfigure
in below.
the figure below.
Caged type,Caged type,
Separator type
Separator type
An example
An example
of procedure
of procedure
for bearing
for bearing
selection
selection

Confirmation
Confirmation
of of ● Identify the
● machine
Identify the
andmachine
place where
and place
the bearing
where is
thetobearing
be used.
is to be used.
C
1 1
Crossed Crossed Full Full ● Confirm ● theConfirm
requirements
the requirements
for bearingsforsuch
bearings
as required
such asbearing
required bearing
Roller Bearings
complementcomplement
Roller Bearings J1∼ J1∼ requirements
requirements
and and performance, performance,
and also confirm
and also
the confirm
operating
theconditions
operating and
conditions
specialand special
type type
operating
operating
conditions
conditions environmentenvironment
conditions. conditions.

● Select the ● bearing

Select thetype bearing
suitabletype
for suitable
the operating
for the operating
D
Slim type Slim type
2 Selection
2 Selection
of bearing
of bearing
type
conditions by
type
conditions
considering
tude, rigidity,tude,
friction,
by considering
rigidity,
space, etc. space, etc.
allowable
load direction
friction,
rotational
load
allowable
and
speed,
direction
magni-and magni-
rotational
bearing
See page See page
speed, bearing
A5 A5

Steel-on-steel
Steel-on-steel
E
● Select the●bearing
Select dimensions
the bearing bydimensions
calculating
bybearing
calculating bearing

3 Selection
3 Selection
type type of of load, life, static
load,
safety
life, static
factor,safety
etc. factor, etc. See page See page
Spherical Spherical bearing bearing
dimensions
dimensions A17 A17
K1∼ K1∼

F
Bushings Bushings

Maintenance-free
Maintenance-free
type type ● Select the
●accuracy
Select the
asaccuracy
required as
by required
the machine
by the
or machine or

4 Selection
4 Selection
accuracy
of
accuracy
of
class, etc.
class, etc.
equipment. equipment. See page See page
A30 A30

Insert type, Insert type,

Lubrication type
Lubrication type
G
● Select the
● Select
radial the
clearance
radial considering
clearance considering
the fit, the fit,

5 5 SelectionSelection
of
radial clearance
of
radial clearance
temperature,temperature,
rotational speed,
and fit and fitand outer rings,
and etc.
rotational
outer rings, etc.
inclination
speed, ofinclination
the innerof theSee
inner
page See page
A37 A37

PILLOBALLs
Die-casting type,
PILLOBALLs
Die-casting type,
Lubrication type
Lubrication type K29∼ K29∼ H
6 Determination
6 Determination
of bearing
of bearing
dimensions,
dimensions,
accuracy,
accuracy,
radial clearance
radial clearance
and fit and fit
Maintenance-free
type
Maintenance-free
type I
Selection
Selection
of of ● Select oil● or Select
greaseoillubrication.
or grease lubrication.

7 7 lubrication
lubrication
and and ● After selection
● After
select the oilselect
of selection
lubricant, of
application
the oilmethod.
in lubricant,
case of oilin lubrication,
application method.
case of oil lubrication,
See page See page

J
A49 A49
L-Balls L-BallsLubrication type
Lubrication type K45∼ K45∼
dust-proof
dust-proof
methodsmethods ● Select the●sealing
Selectmethod
the sealing
according
methodtoaccording
the lubricant.
to the lubricant.

● Design the● surrounding

Design the surrounding
part based on
part
howbased
to mount
on how to mount

Symbol Symbol
Rotation
Oscillating
Rotation
motion
Oscillating
Radial
motion
load
Radial
Axial
load
load
Light
Axial
loadload
Medium
Light
load
load
Medium
Heavy
load
load
Especially
Heavy
excellent
load
Especially
Excellent
excellent Excellent
Normal Normal 8 8 Design of
Design of
surrounding
surrounding
part part
or dismount or
anddismount
based on
and
mounting
based on
dimensions.
mounting dimensions. See page See page
A57 A57
K

9 Determination
9 Determination
of final specifications
of final specifications
of the bearing
of the bearing
and the and
surrounding
the surrounding
part part
L

A15 A16
Basic Dynamic Load Rating Basic rating life A
Roller bearings
and Life The basic rating life is defined as the total number of
Rotational speed min-1
n
10
15 20 30 40 60 80
100
150 200 300 400 600 800
1000
1500 2000 3000 4000 6000 8000
10000
15000 20000 30000 40000 60000
revolutions that 90% of a group of identical bearings fn
Velocity factor

B
1.4 1.3 1.2 1.1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.28 0.24 0.22 0.18 0.16 0.14 0.12 0.106
Life can be operated individually under the same condi- 1.44 1.0 0.20
tions free from any material damage caused by rolling 200 1000 10000 80000
h 300 400 500 600 700 800 900 2000 3000 4000 6000 8000 20000 40000 60000
Basic rating life represented by service hours
Rolling bearings will suffer damage due to various fatigue. Lh
fh
Life factor 0.80 0.85 0.90 0.95 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9
2.5 3.5 4.5
causes during service. Damage such as abnormal For rotation at a constant rotational speed, the basic 0.76 1.0 2.0 3.0 4.0 4.6
wear, seizure, and cracks is caused by improper use, rating life can be represented by the total service
including incorrect mounting, lack of oil, dust intrusion
and so on, and can be avoided by remedying these
hours. C
Ball bearings
causes. However, bearings will eventually be dam- Basic dynamic load rating 10 100 1000 10000
aged due to fatigue-flaking even if used properly. 　　　　　　　Rotational speed min
n
-1 15 20 30 40 60 80 150 200 300 400 600 800 1500 2000 3000 4000 6000 8000 15000 20000 30000 40000 60000

D
fn
When a bearing rotates under load, the raceways and The basic dynamic load rating is defined as the con- Velocity factor 1.4 1.3 1.2 1.1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.28 0.24 0.22 0.18 0.16 0.14 0.12 0.09 0.082
1.49 1.0 0.20 0.10
the rolling elements are subjected to repeated stress- stant radial load (in the case of radial bearings) or the 200 1000 10000 80000
h 300 400 500 600 700 800 900 2000 3000 4000 6000 8000 20000 30000 40000 60000
es concentrated on the part close to the surface. constant axial load acting along the bearing central Basic rating life represented by service hours Lh
axis (in the case of thrust bearings) that allows a fh
Fatigue, therefore, occurs in the surface layer, pro- Life factor
0.74
0.80 0.90
1.0
1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9
2.0
2.5
3.0
3.5
4.0
4.5
5.0 5.4

E
ducing damage in the form of scaling. This is called basic rating life of 1,000,000 revolutions.
flaking (spalling). When this occurs, the bearing can Fig. 2 Scales for rating life calculation
no longer be used. Calculation of rating life

Bearing Life The relationship among the basic rating life, basic

Bearing life is defined as the total number of revolu-

dynamic load rating and dynamic equivalent load
(bearing load) of rolling bearings is as follows: Bearing life factors for various machines
F
（      ）
tions (or total service hours at a constant rotational C p
L10 ＝ 　   …………………………………… (1)
speed) before a sign of the first flaking appears on the 　　　   　 P The required life of the bearing must be determined

G
rolling surface of raceway or rolling elements. 　　where, L10 ：Basic rating life,　106 rev. according to the machine in which the bearing is to be
However, even when bearings of the same size, C ：Basic dynamic load rating,　N used and the operating conditions.
structure, material and heat treatment are subjected P ：Dynamic equivalent load,　N Table 1 shows reference values of life factors for
to the same conditions, the bearing lives will show ：E xponent, Roller bearing: 10/3
p selecting a bearing for each machine.
variation (See Fig. 1.). This results from the statistical
H
Ball bearing: 3
nature of the fatigue phenomenon.
Accordingly, when the rotational speed per minute is Table 1 Life factor of bearings f h for various machines
In selecting a bearing, it is incorrect to take an aver-
given, the basic rating life is represented as the total
age life for all bearings as the design standard. It is Machine and life factor f h
service hours according to the following equations: Operating conditions
more practical to consider a bearing life that is reliable 〜3 2〜4 3〜5 4〜7 6〜
106L10
I
p
fo r t h e gr e a t e r p r o p o r t i o n o f b e a r i n g s u s e d . 　　　L h ＝ 60n ＝  500 f h 　……………………(2) Occasional or short term usage ・Power tools ・Agricultural machines
　 　
Therefore, the basic rating life defined in the following
is used. 　　　f   h ＝ f   n C　  …………………………………(3) Infrequent usage but requiring ・Construction machinery ・Conveyors
　P
reliable operation ・Elevators

（　　    …………………………………
        
n ）
1/p
33.3
　　　f n ＝ (4)
　　where, L h ：Basic rating life represented by
Intermittent operation but for ・Roll neck of rolling mills
comparatively long periods
・Small motors
・Deck cranes
・Factory motors
・Machine tools
・Crane sheaves
・Compressors
J
Basic rating life

・General cargo cranes ・General gear units ・Important gear units

service hours,　h
Failure probability density (Frequency of failure)

・Passenger cars ・Printing machines

n ：Rotational speed,　min-1


f h ：Life factor
f n ：Velocity factor
Operated in excess of 8 hours
per day or continuously for an
・Escalators ・Centrifugal separators
・Blowers
・Paper making machines
K
Average life

extended time ・Wood working machines

In addition, the rating life can be calculated by obtain-
・Plastic extruding machines
ing f h and f n from the life calculation scales of Fig. 2.

L
Continuous use for 24 hours and ・Water supply equipment
accidental stops not allowed ・Power station equipment

Rolling fatigue life

Fig. 1 Variation of rolling fatigue life

M

1N=0.102kgf=0.2248lbs.
A17 1mm=0.03937inch
A18
Life of oscillating bearing bearing life adjustment factors a1, a2 and a3, respec-
tively.
Life adjustment factor for operating conditions　a 3 Correction of basic dynamic load rating
for temperature and hardness
A
The life of an oscillating bearing can be obtained from This factor helps take into account the effects of oper-
L na ＝  a 1 a 2 a 3 L 10   …………………………… (6)
equation (5). 　　　 ating conditions, especially lubrication on the bearing. Temperature factor

B
90 C p 　　where,　L na：Corrected rating life,　106  rev. The bearing life is limited by the phenomenon of
　　　 　θ P（    ）
LOC ＝ 　   　 ………………………………(5)
a 1 ： Life adjustment factor for reliability fatigue which occurs, in general, beneath surfaces The operating temperature for each bearing is deter-
　　where, L OC： B asic rating life of oscillating a 2 ： Life adjustment factor for special subjected to repeated stresses. Under good lubrica- mined according to its material and structure. If spe-
bearing,　106 cycles tion conditions where the rolling element and raceway cial heat treatment is performed, bearings can be
bearing properties
surfaces are completely separated by an oil film and used at temperatures higher than +150°C. As the
2θ ： Oscillating angle, deg. (See Fig.3)
P ： Dynamic equivalent load,　N
a 3 ： Life adjustment factor for operat-
ing conditions
surface damage can be disregarded, a 3 is set to be 1.
However, when conditions of lubrication are not good,
allowable contact stress gradually decreases when
the bearing temperature exceeds 150°C, the basic
C
Therefore, when the oscillating frequency n 1min-1 is
namely, when the viscosity of the lubricating oil is low dynamic load rating is lowered and can be obtained
given, the basic rating life as represented by total Life adjustment factor for reliability　a 1 or the peripheral speed of the rolling elements is by the following equation:
oscillating hours can be obtained by substituting n 1
for n in equation (2) on page A17.
When 2θ is small, an oil film cannot be formed easily
The reliability of rolling bearings is defined as the pro-
especially low, and so on, a 3< 1 is used.
On the other hand, when lubrication is especially 　　　
C t ＝ f t C     …………………………………… (7) D
portion of bearings having a life equal to or greater
good, a value of a 3 > 1 can be used. When lubrica- 　　where,　C t ： Basic dynamic load rating
between the contact surfaces of the raceway and the than a certain specified value when a group of identi-
tion is not good and a 3 < 1 is used, the life adjustment considering temperature rise, 　N
rolling elements. This may cause fretting corrosion. cal bearings are operated under identical conditions.
factor a 2 cannot generally exceed 1.
In this case, please consult . With respect to individual bearings, it refers to the
probability of the life of a bearing being equal to or


f t ： Temperature factor (See Fig. 4.)
C： Basic dynamic load rating, 　N E
When selecting a bearing according to the basic
greater than a certain specified value. Temperature
dynamic load rating, it is recommended that a suitable
The corrected rating life for a reliability of (100-n )%
value for reliability factor a 1 is chosen for each appli- °C 150 200 250
F
can be obtained using equation (6). Table 2 shows
cation. The selection should be made using the
the values of the life adjustment factor a1 for various ft 1.0 0.95 0.9 0.85 0.8 0.75
(C/P ) or f h values determined by machine type and
reliabilities.
based upon the actual conditions of lubrication, tem-
Fig. 4 Temperature factor
perature, mounting, etc., which have already been
Table 2 Life adjustment factor for reliability a1
G
2θ experienced and obser ved in the same type of Further, if the bearing is used at high temperature, i.e.
machines. 120° C or above, the amount of dimensional displace-
Reliability　% Ln a1
ment gets larger. So special heat treatment is neces-
Fig. 3 Oscillating motion 90 L 10 1 Limiting conditions sary. If needed, please contact .
95 L5 0.62
96
97
L4
L3
0.53
0.44
These bearing life equations are applicable only when
the bearing is mounted and lubricated normally with-
Hardness factor H
Corrected rating life 98 L2 0.33 out intrusion of foreign materials and not used under When the shaft or housing is used as the raceway
99 L1 0.21 extreme operating conditions. surface instead of the inner or outer ring, the surface
When a rolling bearing is used in ordinary applica-
tions, the basic rating life can be calculated by equa-
Life adjustment factor for special bearing properties　a 2
Unless these conditions are satisfied, the life may be
shortened. For example, it is necessary to separately
hardness of the part used as the raceway surface
should be 58 〜 64HRC. I
tions (1) and (2) mentioned previously. consider the effects of bearing mounting errors, If it is less than 58HRC, the basic dynamic load rating is
This basic rating life applies to bearings which require The bearing life is extended or shortened according to excessive deformation of housing and shaft, centrifu- lowered and can be obtained by the following equation:
a reliability of 90%, have ordinary bearing properties gal force acting on rolling elements at high-speed rev-
J
the quality of the material, the manufacturing technol- C H ＝ f H C …………………………………… (8)
being made of materials of ordinary quality for rolling ogy of the bearing and its internal design. For these olution, excessive preload, especially large radial 　　　
bearings, and are used under ordinary operating con- special bearing life properties, the life is corrected by internal clearance of radial bearings, etc. 　　where, C H ： Basic dynamic load rating
ditions. the life adjustment factor for special bearing proper- When the dynamic equivalent load exceeds 1/2 of the considering hardness, 　N
In some applications, however, it is necessary to ties a 2. basic dynamic load rating, the life equations may not f H ： Hardness factor (See Fig. 5.)
obtain a rating life that applies to bearings which
require high reliability, have special bearing properties
The table of dimensions for Bearings shows the
values of the basic dynamic load rating which are
be applicable.
C ： Basic dynamic load rating　N K
or are used under special operating conditions. The determined taking into consideration the fact that Hardness of raceway surface
corrected rating life for these special cases can be bearing life has been extended by improved quality of HRC 60 50 40 30 20

L
obtained from the following equation by using the materials and advances in manufacturing technolo-
gies. Therefore, the bearing life is calculated using fH 1 0.8 0.6 0.4 0.2 0.1
equation (6) usually assuming a 2 = 1.
Fig. 5 Hardness factor

1N=0.102kgf=0.2248lbs.
A19 1mm=0.03937inch
A20
Basic Static Load Rating and Static safety factor Calculation of Bearing Loads Load factor A
Static Safety Factor The basic static load rating gives the theoretical allow-
The loads acting on bearings include the weight of the
Although radial loads and axial loads can be obtained
able limit of the static equivalent load. Normally, this by calculation, it is not unusual for the actual bearing
machine parts supported by the bearings, the weight
Basic static load rating
B
limit is corrected by considering the operating condi- loads to exceed the calculated loads, due to vibration
of the rotating body, loads produced when operating
tions and the requirements for the bearing. The cor- and shocks produced when operating the machine.
the machine, loads by belts or gears transmitting
When a bearing at rest sustains a heavy load or a rection factor, namely, the static safety factor f s is The actual bearing load is obtained from the following
power, and various other loads.
bearing rotating at a relatively low speed receives a defined as in the following equation and its general equation, by multiplying the calculated load by the
These loads can be divided into radial loads perpen-
heavy shock load, the contact stress may exceed a values are shown in Table 4. load factor:
C
dicular to the central axis of the bearings and axial
certain limiting value, producing a local permanent C0
f s ＝　　   ………………………………………(9) loads parallel to the central axis, and they act inde- F ＝ f w Fc    ……………………………………(10)
deformation in the raceways or the rolling elements, 　　　 P0 　　　
pendently or in combination with other loads. In addi-
and subsequently causing noise or vibration or lower- 　　where, C 0 ： Basic static load rating,　N tion, the magnitude of vibration or shocks on the bear- 　　where,　F ：Bearing load,　N
ing the rotating performance. The basic static load P 0 ： Static equivalent load, 　N fw ：Load factor (See Table 6.)
ings varies depending on the application of the
rating is, therefore, determined as a guideline for the
maximum allowable load for the bearing at rest, under Table 4 Static safety factor
machine. Thus, theoretically calculated loads may
not always be accurate and have to be corrected by
Fc ：Theoretically calculated load, 　N
D
which the permanent deformation will not exceed a
multiplying various empirical factors to obtain the Table 6 Load factor
certain limit value, and the lowering of the rotating Operating conditions of the bearing fs actual bearing loads.

E
performance will not occur. Its definition is given as Operating conditions Example fw
follows. When high rotational accuracy is required ≧3
The basic static load rating is the static load that gives For ordinary operation conditions ≧ 1.5 Smooth operation Electric motors, Air conditioning equipment,
the contact stress shown in Table 3 at the center of
Load distribution to bearings without shocks Measuring instruments, Machine tools
1 〜 1.2
For ordinary operation conditions not
the contact area of the rolling element and the race- requiring very smooth rotation ≧1 Reduction gearboxes, Vehicles, Textile
Table 5 shows examples of calculations where static
way receiving the maximum load. A radial load con-
stant in direction and magnitude is used in the case of
When there is almost no rotation loads are acting in radial direction.
Ordinary operation
machinery, Paper making machinery
1.2 〜 1.5
F
Operation subjected to Rolling mills, Rock crushers, Construc-
radial bearings, while an axial load constant in magni- 1.5 〜 3
In case of Shell Type Needle Roller Bearings of which vibration and shocks tion machinery
tude acting along the bearing central axis is used in

G
the case of thrust bearings. outer ring is drawn from a thin steel plate and then
carburized and quenched, it is necessary to use a sta-
Table 3 tic safety factor of 3 or more.

Type of bearing Contact stress MPa

Roller bearings 4 000

Table 5 Load distribution to bearings
H
Example Bearing load
Self-aligning ball bearings 4 600
Other ball bearings 4 200
a b

dK r 1 ＋ bK r 2
I
F r 1=
f

Kr1 Kr2 cK r 1 ＋ aK r 2
F r 2=
J
Fr1 Fr2
f
c d

a
d

b c
K
gK r 1 ＋ bK r 2 − cK r 3
F r1=
f

Kr1
Fr1
Kr2
Fr2
Kr3
F r2=
aK r 2 ＋ dK r 3 − eK r 1 L
f
e f

M
g

1N=0.102kgf=0.2248lbs.
A21 1mm=0.03937inch
A22
Bearing loads in case of belt or chain transmission H Mean equivalent load corresponding to fluctuating load A
∫
　　　T =9550000　　  …………………………… (14)  N
n p 1 p
F m =   
　　                                              ……………………
F n  d N (19)
When power is transmitted by a belt or chain, the load T When the load applied to the bearing fluctuates, the
N 0
　　　K t =　　   …………………………………… (15)
acting on the pulley or sprocket wheel is obtained R bearing life is calculated by using the mean equivalent 　　where,　F m：Mean equivalent load,　N
load Fm, which is a constant load that will give the 　 N ：Total number of revolutions,　rev.
B
from the following equations:
　　　K s = K t tan  θ   ………………………………(16)
bearing a life equal to that produced under the fluctu- 　 F n：Fluctuating load,　N
H
　　　T = 9550000　　  …………………………… (11) ating load. The mean equivalent load is obtained 　 p ：Exponent, Roller bearing = 10/3
n 　　　K c=  K t 2＋K s2 = K t  sec θ …………………(17)
from the following equation: Ball bearing = 3
T
　　　K t = 　　   ……………………………………(12)
R 　　 where, T ：Torque applied to gear,　N-mm
　K t：Tangential force acting on gear,　N
Table 9 shows examples of the calculation of mean
equivalent loads for various fluctuating loads.
C
　　where,
T ：Torque acting on pulley or sprocket
　K s：Radial force acting on gear,　N
wheel, 　N-mm
　K c：Resultant normal force on gear tooth surface,　N
K t：Effective transmitting force of belt or chain,　N
H ：Transmitting power,　kW


　H ：Transmitting power,　kW
　n ：Rotational speed,　min
-1
Table 9 Mean equivalent load for the fluctuation load
D
n ：Rotational speed,　min Mean equivalent load　F m
-1
Type of fluctuating load
　R ：Pitch circle radius of drive gear,　mm
R ：E f f e c t i v e r a d i u s o f p u l l e y o r
　θ：Pressure angle of gear,　deg.
sprocket wheel,　mm
E
F1
1 (F p  N ＋ F    N
F m = 2 ＋…＋ F n   N n)
p p p
F 1  1  2 
For belt transmission, the load K r acting on the pulley F2 Fm N p

shaft is obtained from the following equation, multiply- Kt Step load

where,　N 1：Total number of revolutions under load F 1 rev.
ing the effective transmitting force K t by the belt factor Fn
　　　　N 2：Total number of revolutions under load F 2 rev.
f b shown in Table 7. N1 N2
N
Nn
　　　　N n：Total number of revolutions under load F n rev.
F
Ks R
　　K r = f b K t   ………………………………………(13)

1
F m = ( 2F max ＋ F min )
G
Fmax
Table 7 Belt factor F 3
Fm
Monotonously
Type of belt fb changing load where,　F max：Maximum value of fluctuating load,　N
Fmin
　　　　F min ：Minimum value of fluctuating load,　N
V-belts 2   〜 2.5 Fig. 6 N

Timing belts 1.3 〜 2 H

Plain belts (with tension pulley) 2.5 〜 3 In this case, the resultant normal force on the tooth
Fmax
Plain belts 4   〜 5 surface acts as the radial force to the shaft and the F Fm
magnitude of vibration or shocks varies depending on 　F m ≒ 0.65 F max
In the case of chain transmission, a value of 1.2 to 1.5
is taken as the chain factor corresponding to f b. The
t h e a c c u ra c y a n d s u r fa c e f i n i s h o f t h e g e a r.
Therefore, the radial load K r applied to the shaft is N
I
Sinusoidally
load acting on the sprocket wheel shaft is obtained obtained from the following equation, multiplying the
fluctuating load
from equation (13) in the same manner as the belt resultant normal force K c on gear tooth surface by the

J
F Fmax
transmission. gear factor f z shown in Table 8. Fm

　F m ≒ 0.75 F max
N
Bearing loads in case of gear transmission 　　　K r = f z K c   ……………………………………(18)

K
When power is transmitted by gears, the force acting Table 8 Gear factor
on the gears varies according to the type of gear. FS FR
Type of gear fz F m = F S ＋ F R −
Spur gears produce radial loads only, but helical Fs
FS ＋ FR
Stationary load plus
gears, bevel gears and worm gears produce axial
Precision gears rotating load where,　F S：Stationary load,　N
loads in addition to radial loads. Taking the simplest 1.05 〜 1.1 　　　　F R：Rotating load,　N
L
FR
(Pitch error and form error: Less than 0.02mm)
case of spur gears as an example, the bearing load is
obtained from the following equations: Ordinary machined gears
1.1 〜 1.3
(Pitch error and form error: 0.02 〜 0.1mm)

1N=0.102kgf=0.2248lbs.
A23 1mm=0.03937inch
A24
Equivalent load Static equivalent load
Boundary Dimensions and Needle Roller Cage
A
The loads applied to the bearing are divided into radi- When both radial load and axial load are applied to Identification Number 　E w：Nominal roller set outside diameter
al loads that are applied perpendicular to the central the bearing simultaneously, the virtual load, acting on 　F w：Nominal roller set bore diameter
Boundary dimensions
B
axis and axial loads that are applied in parallel to the the center of the bearing, that will produce a maxi- 　B c ：Nominal cage width
central axis. These loads act independently or in com- mum contact stress on the contact surface between
bination with other loads. the rolling element and the raceway equal to that Examples of symbols for quantities indicating the
given by the radial load and the axial load is defined boundary dimensions of Needle Roller Bearings Bc

Dynamic equivalent load as a static equivalent load. are shown below. For details, see the table of dimen-

When both radial load and axial load are applied to

In the case of needle roller bearings, radial bearings
receive only radial loads and thrust bearings receive
sions for each model. C
the bearing simultaneously, the virtual load, acting on only axial loads. Accordingly, radial loads are directly Machined Type Needle Roller Bearing
the center of the bearing, that will give a life equal to used for the radial bearings, while axial loads are

Fw
Ew
that under the radial load and the axial load is defined directly used for the thrust bearings. 　d ： Nominal bearing bore diameter
as a dynamic equivalent load. 　D ： Nominal bearing outside diameter
In the case of needle roller bearings, radial bearings [For radial bearings] 　B ： Nominal inner ring width
receive only radial loads and thrust bearings receive 　　　P 0 r  = F r ………………………………………(22) 　C ： Nominal outer ring width
only axial loads. Accordingly, radial loads are directly
E
[For thrust bearings] 　F w ： Nominal roller set bore diameter
used in the life calculation of the radial bearings, while 　　　P 0 a = Fa  ………………………………………(23) 　r ： Chamfer dimensions of inner and outer rings Fig. 9 Needle Roller Cage
axial loads are directly used for the thrust bearings.
　r s min ： S m a l l e s t p e r m i s s i bl e s i n g l e c h a m fe r
　　where,　P 0r ：Static equivalent radial load,　N dimensions of inner and outer rings
[For radial bearings] 　　　　　　P 0a：Static equivalent axial load,　N Thrust Roller Bearing
　　　P r = F r  ………………………………………(20)
[For thrust bearings]
　　　　　　F r ：Radial load,　N
B
F
　　　　　　F a ：Axial load,　N C 　D c ：Nominal cage outside diameter
　　　P a= F a ………………………………………(21)
r 　d c ：Nominal cage bore diameter
　D w：Nominal roller diameter
　　where,　P r：Dynamic equivalent radial load,　N
G
r

　　　　　　Pa：Dynamic equivalent axial load,　N

　　　　　　F r：Radial load,　N

Fw
D
d
　　　　　　F a：Axial load,　N r Dw

r H
Fig. 7 Machined Type Needle Roller Bearing

Dc

dc
Shell Type Needle Roller Bearing

　D ：Nominal bearing outside diameter

　F w：Nominal roller set bore diameter
　C ：Nominal outer ring width　 J
Fig. 10 Thrust Roller Bearing
C

Fw
D
L
Fig. 8 Shell Type Needle Roller Bearing

1N=0.102kgf=0.2248lbs.
A25 1mm=0.03937inch
A26
Identification Number 4 Cage symbol  8 Classification symbol A
The identification number of Bearings consists Symbol Descriptions
Symbol Descriptions
of a model number and supplemental codes. The
(None) JIS Class 0
B
descriptions of typical codes and their arrangements N Made of synthetic resin
are shown below. There are many codes other than P6 JIS Class 6
V No cage or full complement
those described. See the section of identification
P5 JIS Class 5
number of each bearing.
5 Seal or shield symbol P4 JIS Class 4
Table 10 Arrangement of identification number of bearing
Symbol Descriptions
C
Model code 1
Model number Table 11 Indication of boundary dimensions
Boundary dimensions Z With dust cover
2
Model number
Material symbol 3 ZZ
U
With shields on both sides

With a seal on one side

Bearing type
Model code Indication of boundary dimensions D
Cage symbol 4 TA，TLA，YT，YTL Roller set bore diameter + Outer ring width
Shield symbol UU With seals on both sides Shell Type Needle Roller Bearings
BA，BHA，YB，YBH Roller set bore diameter + Outer ring width (1)
Supplemental Seal symbol,
5
E
code 2RS With seals on both sides Needle Roller Cages for General Usage KT，KTW Roller set bore diameter + Roller set outside diameter + Cage width
Bearing ring shape symbol 6 Needle Roller Cages for Engine Connecting Rods KT…EG，KTV…EG Roller set bore diameter + Roller set outside diameter + Cage width
Clearance symbol 7 NA，RNA Dimension series + Bore diameter number
6 Bearing ring shape symbol TR，TAF，GTR Roller set bore diameter + Bearing outside diameter + Bearing width
Classification symbol 8
F
Machined Type Needle Roller Bearings TRI，TAFI，GTRI Bearing bore diameter + Bearing outside diameter + Outer ring width
Symbol Descriptions
BR Roller set bore diameter + Bearing outside diameter + Bearing width (1)
1 Model code NR With stop ring on outer surface of outer ring BRI Bearing bore diameter + Bearing outside diameter + Outer ring width (1)
The model code represents the bearing series. The RNAF，RNAFW Roller set bore diameter + Bearing outside diameter + Bearing width
features of each bearing series are shown on pages OH (1) With oil hole in bearing ring Needle Roller Bearings with Separable Cage

G
NAF，NAFW Bearing bore diameter + Bearing outside diameter + Bearing width
A5 to A15. J No oil hole
NAU，NAG，NAS Dimension series + Bore diameter number
Roller Bearings
Note(1)　This differs depending on the type of bearing. See the TRU Bearing bore diameter + Bearing outside diameter + Bearing width
2 Boundary dimensions section of each bearing.
NTB，AS，WS，GS Bearing bore diameter + Bearing outside diameter
One of the following four kinds of presentation meth-

H
Thrust Bearings AZ Bearing bore diameter + Bearing outside diameter + Bearing height
ods is used for showing boundary dimensions in the
7 Clearance symbol AZK Bearing bore diameter + Bearing outside diameter + Roller diameter
identification number, which vary depending on the
bearing series. Table 11 shows the presentation NAX，NBX Roller set bore diameter + Assembled bearing width
Symbol Descriptions
methods of boundary dimensions for each model Combined Type Needle Roller Bearings NAXI，NBXI Innerring bore diameter + Assembled bearing width
Dimensional series + Bore diameter number
I
code. C2 NATA，NATB
C2 clearance
CF，NUCF，CFS Stud diameter
(None) CN clearance
　(a)Dimension series + Bore diameter number Cam Followers CFKR Bearing outside diameter
　(b)B ore diameter or roller set bore diameter + C3 C3 clearance CR，CRH Bearing outside diameter (1)
Outside diameter or roller set outside diameter + NAST，NART，NURT Bearing bore diameter
J
C4 C4 clearance Roller Followers
Width CRY Bearing outside diameter (1)
C5 C5 clearance
　(c)Bore diameter or roller set bore diameter + Width Crossed Roller Bearings CRBH(V)，CRB，CRBS，CRBT Bearing bore diameter + Bearing width
　(d)Basic diameter T1 SB…A，GE Inner ring bore diameter
Special radial clearance Spherical Bushings
SBB Inner ring bore diameter (1)
K
C1 (Applicable to Crossed Roller Bearings)
3 Material symbol PILLOBALLs PB,PHS,POS,PHSB,POSB,PHSA Inner ring bore diameter
C2
L-Balls LHSA，LHS Screw size
Symbol Type of material
Seals for Needle Roller Bearings OS，DS Shaft diameter + Seal outside diameter + Seal width
WR Shaft diameter

L
F Stainless steel for bearing rings and rolling elements Cir-clips for Needle Roller Bearings
AR Bore diameter
Note(1)　The nominal dimensions of inch series bearings are indicated in units of 1/16 inch.

1N=0.102kgf=0.2248lbs.
A27 1mm=0.03937inch
A28
 Example of identification number Accuracy A
(a) Example of "Dimension series + Bore diameter number" (b) Example of "Bore diameter or roller set bore diameter + The accuracy of Needle Roller Bearings con-
Remarks
Outside diameter or roller set outside diameter + width" for ms to JIS B 1514-1~-3 (Rolling bearings -
Tolerances of bearings), and the dimensional accura-
cy and rotational accuracy are specified. The speci-
The meanings of the new symbols for quantities
used for accuracy of radial bearings are as
B
Supplemental Supplemental
fied items are shown in Fig. 11. follows:
Model number code Model number code
Needle Roller Bearings are classified into 4 classes of ① ∆ represents the deviation of a dimension from
NA 49 02 C2 P6 KT 5 8 8 N
Model code
accuracy. These classes are represented by the
numbers 0, 6, 5 and 4, written in order of increasing
the specified value.
② V represents the variation of a dimension. C
Model code
accuracy. ③ Suffixes s , m , and p represent a single (or
Dimension series Roller set bore diameter Table 12 shows the accuracy for the inner rings of actual) measurement, a mean measurement,

D
radial bearings, Table 13 shows the accuracy for the and a measurement in a single radial plane,
Bore diameter number Roller set outside diameter outer rings of radial bearings, Table 14 shows the tol- respectively.
erances for the smallest single roller set bore diame- [Example] Vdp means the difference between
Clearance symbol Cage width
ter of radial bearings, and Table 15 shows the permis- the largest and the smallest of the bore
Classification symbol sible limit values of chamfer dimensions of radial

E
Cage symbol diameters in a single radial plane (circularity).
bearings. For thrust bearings, see the section on
Vdmp means the difference between the largest
accuracy of Thrust Bearings. Note that the series of
and the smallest of the single plane mean bore
Shell Type Needle Roller Bearings, Roller Bearings,
(c) Example of "Bore diameter or roller set bore diameter + width" (d) Example of "Basic diameter" diameters (cylindricity).
Cam Followers, Roller Followers, Combined Type

F
Needle Roller Bearings, and Crossed Roller Bearings
Supplemental have special accuracy. For further details, see the
Supplemental
Model number code Model number code section on accuracy of each bearing series.

NAX 20 30 Z CF 10 V B UU
Model code Model code
Single bore diameter deviation  ∆ ds
G
Single plane mean bore diameter deviation   ∆ dmp
Roller set bore diameter Basic diameter (Stud diameter)
Single outside diameter deviation  ∆ Ds
Deviation of boundary

H
Assembled bearing width Cage symbol dimensions
Single plane mean outside diameter deviation  ∆ Dmp

Shield symbol Shape of stud head Deviation of a single inner ring width  ∆ Bs

Seal symbol Deviation of a single outer ring width  ∆ Cs

I
Accuracy of boundary
dimensions Bore diameter variation in a single radial plane  Vdsp

Mean bore diameter variation  Vdmp

Outside diameter variation in a single radial plane  VDsp

J
Variation of boundary
dimensions
Mean outside diameter variation  VDmp

Accuracy of Inner ring width variation  VBs

bearings
Outer ring width variation  VCs

Radial runout of assembled bearing inner ring  Kia

K
Assembled bearing inner ring face runout with raceway  Sia

Inner ring reference face runout with bore  Sd

L
Rotational
accuracy
Radial runout of assembled bearing outer ring  Kea

Assembled bearing outer ring face runout with raceway  Sea

Variation of outside surface generatrix inclination with outer ring reference face  SD

Fig. 11 Accuracy of bearings

M

A29 A30
Table 12 Tolerances for inner ring
d ∆ d mp ∆ ds Vd sp Vd mp K ia Sd S ia(3) ∆ Bs VBs
unit: μ m

d
A
Nominal bearing Single plane mean bore diameter deviation Single bore Bore diameter variation in a single radial plane Mean bore diameter Radial runout of Inner ring Assembled bearing Deviation of a single inner ring width Inner ring width variation Nominal bearing
bore diameter diameter variation assembled bearing reference face inner ring face bore diameter
deviation Diameter series 8, 9(1) Diameter series 0(2) inner ring runout with bore runout with raceway

mm Class 0 Class 6 Class 5 Class 4 Class 4

Class Class Class Class Class Class Class Class Class Class Class Class
0 6 5 4 0 6 5 4 0 6 5 4
Class Class Class Class Class Class Class Class
0 6 5 4 5 4 5 4
Class 0 Class 6
Class Class Class Class
Class 5
0 6
Class 4
5 4
mm B
Over Incl. High Low High Low High Low High Low High Low Max. Max. Max. Max. Max. Max. High Low High Low High Low High Low Max. Over Incl.
      2.5 10 0 - 8 0 - 7 0 - 5 0 - 4 0 - 4 10   9   5   4   8   7   4 3   6   5   3 2 10   6   4 2.5   7 3   7 3 0 - 120 0 - 120 0 - 40 0 - 40 15 15   5 2.5       2.5 10
    10 18 0 - 8 0 - 7 0 - 5 0 - 4 0 - 4 10   9   5   4   8   7   4 3   6   5   3 2 10   7   4 2.5   7 3   7 3 0 - 120 0 - 120 0 - 80 0 - 80 20 20   5 2.5     10 18
    18
    30
30
50
0

0
- 10
- 12
0

0
- 8
- 10
0

0
- 6
- 8
0

0
- 5
- 6
0

0
- 5 13
- 6 15
10
13
  6
  8
  5
  6
10
12
  8
10
  5
  6
4
5
  8
  9
  6
  8
  3
  4
2.5
3
13
15
  8
10
  4
  5
3
4
  8
  8
4
4
  8
  8
4
4
0

0
- 120
- 120
0

0
- 120

- 120
0

0
- 120

- 120
0

0
- 120

- 120
20
20
20
20
  5
  5
2.5     18
3     30 50
30
C
    50 80 0 - 15 0 - 12 0 - 9 0 - 7 0 - 7 19 15   9   7 19 15   7 5 11   9   5 3.5 20 10   5 4   8 5   8 5 0 - 150 0 - 150 0 - 150 0 - 150 25 25   6 4     50 80
    80 120 0 - 20 0 - 15 0 - 10 0 - 8 0 - 8 25 19 10   8 25 19   8 6 15 11   5 4 25 13   6 5   9 5   9 5 0 - 200 0 - 200 0 - 200 0 - 200 25 25   7 4     80 120
  120 180 0 - 25 0 - 18 0 - 13 0 - 10 0 - 10 31 23 13 10 31 23 10 8 19 14   7 5 30 18   8 6 10 6 10 7 0 - 250 0 - 250 0 - 250 0 - 250 30 30   8 5   120 180
  180
  250
250
315
0
0
- 30
- 35
0
0
- 22
- 25
0
0
- 15
- 18
0 - 12 0 - 12 38
44
28
31
15
18
12 38
44
28
31
12
14
9 23
26
17
19
  8
  9
6 40
50
20
25
10
13
8 11
13
7 13
15
8 0
0
- 300
- 350
0
0
- 300
- 350
0
0
- 300
- 350
0 - 300 30
35
30
35
10
13
6   180
  250
250
315 D
  315   400 0 - 40 0 - 30 0 - 23 50 38 23 50 38 18 30 23 12 60 30 15 15 20 0 - 400 0 - 400 0 - 400 40 40 15   315   400
  400   500 0 - 45 0 - 35 56 44 56 44 34 26 65 35 0 - 450 0 - 450 50 45   400   500
  500   630 0 - 50 0 - 40 63 50 63 50 38 30 70 40    0 - 500 0 - 500 60 50   500   630
  
  630
  800
1000
  800
1000
1250
0
0
0
- 75
- 100
- 125
80
90
100
0
0
0
- 750
- 1000
- 1250
70
80
100
  630
  800
1000
  800
1000
1250
E
1250 1600 0 - 160 120 0 - 1600 120 1250 1600
1600 2000 0 - 200 140 0 - 2000 140 1600 2000
Note(1)　Applicable to all series except NAS series
(2)　Applicable to NAS series F
(3)　Applicable to NATA and NATB series

G
Table 13 Tolerances for outer ring unit: μ m

D ∆ Dmp ∆ Ds VD sp(1) V D mp Kea SD S ea(4) ∆ Cs VCs D

Nominal bearing Single plane mean outside diameter deviation Single out- Outside diameter variation in a single radial plane Mean outside Radial runout of Variation of outside Assembled Deviation of a single Outer ring width variation Nominal bearing
outside diameter side diam- diameter variation assembled bearing surface generatrix bearing outer outer ring width outside diameter
eter devia- outer ring inclination with outer ring face runout
Open bearing Bearing with seal or shield
tion ring reference face with raceway

H
Diameter series 8, 9(2) Diameter series 0(3) Diameter series 0(3)
mm Class Class Class Class Class Class Class Class Class Class Class Class Class Class Class Class mm
Class 0 Class 6 Class 5 Class 4 Class 4 Class 6 Class 5 Class 4 Class 5 Class 4 Class 0, 6, 5, 4 Class 0 Class 6 Class 5 Class 4
0 6 5 4 0 6 5 4 0 6 5 4 0 6 5 4
Over Incl. High Low High Low High Low High Low High Low Max. Max. Max. Max. Max. Max. Max. High Low Max. Over Incl.
      2.5 6 0 - 8 0 - 7 0 - 5 0 - 4 0 - 4 10   9   5   4   8   7   4   3   9   6   5   3 2 15   8   5   3   8   4   8   5   5 2.5       2.5 6

I
      6 18 0 - 8 0 - 7 0 - 5 0 - 4 0 - 4 10   9   5   4   8   7   4   3   9   6   5   3 2 15   8   5   3   8   4   8   5   5 2.5       6 18
    18 30 0 - 9 0 - 8 0 - 6 0 - 5 0 - 5 12 10   6   5   9   8   5   4 10   7   6   3 2.5 15   9   6   4   8   4   8   5   5 2.5     18 30
    30 50 0 - 11 0 - 9 0 - 7 0 - 6 0 - 6 14 11   7   6 11   9   5   5 13   8   7   4 3 20 10   7   5   8   4   8   5   5 2.5     30 50
    50 80 0 - 13 0 - 11 0 - 9 0 - 7 0 - 7 16 14   9   7 13 11   7   5 16 10   8   5 3.5 25 13   8   5   8   4 10   5   6 3     50 80
    80 120 0 - 15 0 - 13 0 - 10 0 - 8 0 - 8 19 16 10   8 19 16   8   6 20 11 10   5 4 35 18 10   6   9   5 11   6   8 4     80 120

J
  120 150 0 - 18 0 - 15 0 - 11 0 - 9 0 - 9 23 19 11   9 23 19   8   7 25 14 11   6 5 40 20 11   7 10   5 13   7   8 5   120 150
  150 180 0 - 25 0 - 18 0 - 13 0 - 10 0 - 10 31 23 13 10 31 23 10   8 30 19 14   7 5 45 23 13   8 10   5 14   8 Same as the Same as the   8 5   150 180
  180 250 0 - 30 0 - 20 0 - 15 0 - 11 0 - 11 38 25 15 11 38 25 11   8 23 15   8 6 50 25 15 10 11   7 15 10 tolerance tolerance 10 7   180 250
values of ∆ Bs values of VBs
  250   315 0 - 35 0 - 25 0 - 18 0 - 13 0 - 13 44 31 18 13 44 31 14 10 26 19   9 7 60 30 18 11 13   8 18 10 11 7   250   315
  315   400 0 - 40 0 - 28 0 - 20 0 - 15 0 - 15 50 35 20 15 50 35 15 11 30 21 10 8 70 35 20 13 13 10 20 13 for d of the for d of the 13 8   315   400
  400   500 0 - 45 0 - 33 0 - 23 56 41 23 56 41 17 34 25 12 80 40 23 15 23 same bearing same bearing 15   400   500
  500
  630
  630
800
0
0
- 50
- 75
0
0
- 38
- 45
0
0
- 28
- 35
63
94
48
56
28
35
63 48
94 56
21
26
38
55
29
34
14
18
100
120
50
60
25
30
18
20
25
30
18
20
  500
  630
  630
800
K
  800 1000 0 - 100 0 - 60 125 75 125 75 75 45 140 75   800 1000
1000 1250 0 - 125 160 1000 1250
1250 1600 0 - 160 190 1250 1600
1600
2000
2000
2500
0
0
- 200
- 250
220
250
1600
2000
2000
2500 L
Note(1)　Classes 0 and 6 are applicable to outer rings without stop rings.
(2)　Applicable to all series except NAS series
(3)　Applicable to NAS series

M
(4)　Applicable to NATA and NATB series

1N=0.102kgf=0.2248lbs.
A31 1mm=0.03937inch
A32
Table 14 Tolerances for smallest single roller set
bore diameter F ws min(1) unit: μm
Table 15 Permissible limit values for chamfer
dimensions of radial bearings unit: mm
Methods of Measurement A
Fw ∆ Fws min r s min d r s max Measurement of Needle Roller Bearings is
Nominal roller set bore diameter Deviation of smallest single roller set bore diameter Smallest Nominal bore diameter Largest permissible single chamfer dimension based on JIS B 1515-1, -2 (Rolling bearings-
mm
B
permissible single Tolerances). Tables 16 and 17 show some examples
Over Incl. High Low chamfer dimension Over Incl. Radial direction Axial direction of the methods.
    3     6    ＋ 18 ＋ 10 0.1 ─ ─ 0.55（2）   0.55（2） Special methods are used to measure Shell Type
    6   10   ＋ 22 ＋ 13 0.15 ─ ─   0.6   （2）   0.6   Needle Roller Bearings. Therefore, refer to the sec-
  10   18 ＋ 27 ＋ 16 0.2 ─ ─   0.7   （2）   0.8   tion on accuracy for these bearings on page B3.
  18
  30
  30
  50
＋ 33
＋ 41
＋
＋
20
25 0.3
─
  40
  40
─
  0.8   （2）
  0.8
  1
  1
C
  50   80 ＋ 49 ＋ 30 0.4（1） ─ ─   0.8   1.2 Table 16 Measurement methods of accuracy of boundary dimensions
  80 120 ＋ 58 ＋ 36 ─   40   1.1   （2）   2
120 180 ＋ 68 ＋ 43 0.6
─ Measurement methods Accuracy and definitions
D
  40   1.3   2
180 250 ＋ 79 ＋ 50 ─   50   1.5   3
250 315 ＋ 88 ＋ 56 1
  50 ─   1.9   3 Zero the gauge indicator to the appropri- Calculated mean value of the maximum and minimum
315 400 ＋ 98 ＋ 62 ─ 120   2   3.5 Single bore ate size using gauge blocks or a master d mp values of the single bore diameter within a radial plane.
400 500 ＋ 108 ＋ 68 1.1 ring.
120 ─   2.5   4 diameter In several angular directions and in a sin- Mean bore diameter d sp max ＋ d sp min
d mp ＝
─
E
Note(1)　This is the diameter of the cylinder used instead of the 120   2.3   4 gle radial plane, measure and record the in a single plane 2
inner ring, where the radial clearance becomes 0 at least 1.5 largest and the smallest single bore diam- d sp：Single bore diameter in a single plane
in one radial direction. 120 ─   3   5 eters, d sp max and d sp min, within the mea-
─   80   3   4.5 suring zone (excluding the zone 1.2 times ∆ d mp Deviation of mean bore diameter in a single plane and
2   80 220   3.5   5 the respective maximum allowable cham- Deviation of mean bore nominal bore diameter.
fer dimensions of the inner ring face).
220 ─   3.8   6 Repeat angular measurements and record- diameter in a single ∆ d mp ＝ d mp − d
2.1
─
280
280
─
  4
  4.5
  6.5
  7
ings in several radial planes to determine
the largest and the smallest single bore
plane d ：Nominal bearing bore diameter
F
─ 100   3.8   6 diameter, d s max and d s min. V d sp Deviation of the maximum and minimum values of the
Variation of bore diameter single bore diameter within a radial plane.
2.5（1） 100 280   4.5   6
in a single plane V d sp ＝ d sp max − d sp min
280 ─   5   7

1.2rs max
3
─
280
280
─
  5
  5.5
  8
  8
V d mp
Deviation of the maximum and minimum values of mean bore
diameter in a single plane, for individual raceway rings with
G
Variation of mean
4 ─ ─   6.5   9 essentially cylindrical bore diameter surfaces.
bore diameter
5 ─ ─   8 10 V d mp ＝ d mp max − d mp min
─ ─
H
6 10 13 Deviation of single bore diameter and nominal bore diameter.
∆ ds

1.2rs max
Note(1)　 Not specified in JIS. ∆ ds ＝ d s − d
Deviation of a single
(2)　 The numeric value differs from JIS. d s：Single bore diameter (distance between two parallel straight lines touching
Remark 　Although the exact shape of the chamfer is not specified, bore diameter the intersection of the single bore diameter surface and the radial plane)
its profile in the axial plane must not extend beyond the
imaginary circular arc of radius rs min which is tangential Zero the gauge indicator to the appropri- Calculated mean value of the maximum and minimum
Single D mp
I
to the inner ring side surface and bearing bore surface or ate size using gauge blocks or a master. values of the single outside diameter within a radial plane.
to the outer ring side surface and bearing outside sur- outside In several angular directions and in a sin- Mean outside
gle radial plane, measure and record the diameter in a single D D sp max ＋ D sp min
face. (See Fig. 12.) diameter mp ＝
largest and the smallest single outside 2
diameters, Dsp max and Dsp min, within the plane
D sp：Single outside diameter in a single plane
measuring zone (excluding the zone 1.2
times the respective maximum allowable Deviation of mean outside diameter in a single plane and
chamfer dimensions of the outer ring
face).
∆ D mp
Deviation of mean outside ∆
nominal outside diameter.
D mp ＝ D mp − D
J
Repeat and record measurements in sev- diameter in a single plane
eral radial planes to determine the largest D：Nominal bearing outside diameter
Side surface of

and the smallest single outside diameter,

inner ring or

V D sp Deviation of the maximum and minimum values of the

outer ring

Ds max and Ds min.

K
Variation of outside single outside diameter within a radial plane.
diameter in a single plane V D sp ＝ D sp max − D sp min

1.2rs max
(Radial direction)

rs Deviation of the maximum and minimum values of mean

m V D mp
in
outside diameter in a single plane, for individual raceway
rs max

Variation of mean
rings with essentially cylindrical outside diameter surfaces.
rs min

L
outside diameter V D mp ＝ D mp max − D mp min
Bearing bore or
bearing outside rs min Deviation of single outside diameter and nominal outside diameter.
surface ∆ Ds ∆ Ds ＝ D s − D

1.2rs max
rs max
(Axial direction) Deviation of a single D s：Single outside diameter (distance between two
outside diameter parallel straight lines touching the intersection of the
Fig. 12 Permissible values for chamfer dimensions
single outside diameter surface and the radial plane)
M

1N=0.102kgf=0.2248lbs.
A33 1mm=0.03937inch
A34
 Table 17 Measurement methods for rotational accuracy
A
Measurement methods Accuracy and definitions Accuracy Measurement methods

Fasten the master gauge to a surface plate.

B
Position the bearing on the master gauge and apply Sd Use a precision arbor having a taper of approximately 1 : 5 000 on diameter.
Single bore
the indicator in the radial direction near the middle of Perpendicularity
diameter of Mount the bearing assembly on the tapered arbor and place the arbor
the width on the ring outside surface. Fws In radial bearings without inner rings, the distance
rolling Measure the amount of movement of the outer ring in between two parallel straight lines touching the
of inner ring between two centres so that it can be accurately rotated.
Single bore
element the radial direction by applying sufficient load on the face with Position the indicator against the reference face of the inner ring at a radi-
diameter of roller intersection of the inscribed circle of roller complement
outer ring in the same radial direction as that of the al distance from the arbor axis of half the mean diameter of the face.
complement
C
indicator and in the opposite radial direction. complement and the radial plane. respect to the
Take indicator readings while rotating the inner ring one revolution.
Record indicator readings at the extreme radial posi- bore
tions of the outer ring. Rotate the bearing and repeat
the measurement in several different angular posi- Support the reference face of the outer ring on a surface plate leaving the
tions to determine the largest and the smallest read-
SD inner ring, if an assembled bearing, free. Locate the outer ring cylindrical

1.2rs max
ings, Fws max and Fws min. In radial bearings without inner rings, the minimum value

D
Perpendicularity outside surface against two supports set at 90° to each other to centre the
of the single bore diameter of roller complement.
Measuring Fws min outer ring.
load
of outer ring
Smallest single bore Position the indicator directly above one support. The indicator and the
Remark Diameter of a cylinder where the smallest outside surface
diameter of roller two supports are axially located at the extremes of the measurement zone
single bore diameter of roller complement with respect to (positions 1.2 times the respective maximum allowable chamfer dimen-

1.2rs max
complement

E
has zero radial clearance in at least one Stopper
the face sions of the outer ring face).
Master radial direction.
gauge
Take indicator readings while rotating the outer ring one revolution.

Zero the gauge indicator to the appropriate Use a precision arbor having a taper of approximately 1 : 5 000 on diameter.
height from the reference surface using gauge Deviation of single inner ring width and nominal inner
Inner ring ∆ Bs K ia Mount the bearing assembly on the tapered arbor and place the arbor
blocks or a master.

F
ring width.
width Support one face of the inner or outer ring on Deviation of a single between two centres so that it can be accurately rotated.
Radial runout
three equally spaced fixed supports of equal Position the indicator against the outside surface of the outer ring as close
inner ring width
height and provide two suitable radial supports ∆ Bs ＝ B s − B of inner ring of
as possible to the middle of the outer ring raceway.
on the bore or outside surface set at 90° to each
assembled Hold the outer ring to prevent rotation but ensure its weight is supported
other to centre the inner or outer ring.
Position the indicator against the other face of Deviation of the maximum and minimum values of the bearing by the rolling elements. Take indicator readings while rotating the arbor
V Bs
G
the ring opposite one fixed support.
single inner ring width for individual inner rings. one revolution.
Rotate the inner or outer ring one revolution and
Variation of inner
measure and record the largest and the smallest
single inner (outer) ring width, B s max and B s min, ring width
V Bs ＝ B s max − B s min Use a precision arbor having a taper of approximately 1 : 5 000 on diameter.
(C s max and C s min). K ea Mount the bearing assembly on the tapered arbor and place the arbor
Radial runout
H
between two centres so that it can be accurately rotated.
Deviation of single outer ring width and nominal outer
Outer ring ∆ Cs of outer ring of Position the indicator against the outside surface of the outer ring as close
ring width.
width Deviation of a single assembled as possible to the middle of the outer ring raceway.
outer ring width Hold the inner ring stationary. Take indicator readings while rotating the
∆ Cs ＝ C s − C bearing
outer ring one revolution.

V Cs
Deviation of the maximum and minimum values of the
S ia Support the reference face of the outer ring on a surface plate with a pilot
I
single outer ring width for individual outer rings.
Variation of outer for centering the outside diameter of the ring. Apply a dynamically stable
Axial runout of Load on inner ring
ring width coaxial load to the reference face of the inner ring in order to ensure con-
V C s ＝ C s max − C s min inner ring of

J
tact between rolling elements and raceways.
assembled Position the indicator against the reference face of the inner ring and take
Support the bearing on a surface plate. Zero the
bearing indicator readings while rotating the inner ring one revolution.
gauge indicator to an appropriate height from the sur-
Bearing
face plate using gauge blocks or a master.
height
Place a plate of known thickness on the bearing Deviation of actual bearing height and nominal bearing

K
assembly, apply a dynamically stable coaxial load, and height of the thrust bearing. S ea Support the reference face of the inner ring on a surface plate with a pilot
position the indicator over the centre of the plate.
∆ Ts for centering in the bore of the inner ring. Apply a dynamically stable
Rotate the housing washer several times, to be sure to Axial runout of Load on outer ring
∆ Ts ＝ T s − T coaxial load to the reference face of the outer ring in order to ensure con-
reach the smallest height, and take indicator readings. Deviation of the outer ring of tact between rolling elements and raceways.
actual bearing height
Disk master assembled Position the indicator against the reference face of the outer ring and take
T s：Actual bearing height
T   ：Nominal bearing height
bearing indicator readings while rotating the outer ring one revolution.
L

1N=0.102kgf=0.2248lbs.
A35 1mm=0.03937inch
A36
Clearance 1 Table 18 shows the radial internal clearances of
Needle Roller Bearings with Inner Ring based on JIS
Selection of clearance 　　　∆ C ＝ ∆ F ＋ ∆ E  ………………………………(24)
A
The clearances between the bearing rings and rolling B 1520 (Rolling bearings-Radial internal clearance). Radial clearances of needle roller bearings change 　　where,　∆ C ：Amount of reduction of the radial
elements are known as bearing clearances. When The radial internal clearances are classified into C2, according to bearing fit, temperature difference clearance, mm
　　　　　　∆ F ：Amount of expansion of the out-
B
either the inner or outer ring is fixed and a specified CN, C3, C4, and C5, with clearances increasing in between bearing rings and rolling elements, loads,
measuring load is applied to the free bearing ring this order. CN is used under normal operating condi- etc., and these factors greatly influence bearing life, side diameter of inner ring, mm
inward and outward alternately in the radial direction, tions. When a smaller range in radial internal clear- accuracy, noise, generation of heat, etc. If radial 　　　　　　∆ E ：Amount of shrinkage of the bore
the displacement of the free bearing is referred to as ance than the values shown in Table 18 is required, clearances are too large, noise and vibration will diameter of outer ring, mm
please consult . increase, and if they are too small, abnormally great
C
the radial internal clearance. The amount of measur-
ing load in this case is extremely small, and its values forces are exerted on the contact areas between 1 Amount of expansion of the outside diameter of inner ring
are specified in JIS B 1515-2 (Rolling bearings-Toler- 2 In the case of Shell Type Needle Roller Bearings, raceways and rolling elements, resulting in abnormal-
ances-Part2:Measuring and gauging principles and the correct dimensional accuracy is achieved only ly high heat generation and a decrease in bearing life. ・With solid shaft
methods). after the bearings are press-fitted into the specified Therefore, in the ideal case, the clearance provided
d
housing bore. Therefore, the clearances shown in
Table 18 are not applicable. See page B5.
before mounting should be such that it will become
zero or slightly larger when the bearing has reached
　　　∆ F ＝ ∆ de               ………………………………(25)
F D
steady-state operation and the temperature has ・With hollow shaft
3 For the radial internal clearances of Cam Followers, become constant (saturation temperature). However, d 1 − (d i /d ) 2
Roller Followers and Crossed Roller Bearings, see the it is difficult to achieve this ideal state for all bearings. 　　　∆ F ＝ ∆ de　　　　　　　　　　　　　　　  　   ……(26)
relevant section for each bearing. Under general operating conditions, bearings with CN
F 1 − (d/F ) 2 (d i /d ) 2
　　where,　∆ de ：Effective interference of inner ring, mm
E
clearance are most widely used, and are manufac-
tured to provide satisfactory performance when fitted 　　　　　　d　 ：Bore diameter of inner ring, mm
according to Tables 21 and 22. 　　　　　　F　 ：Outside diameter of inner ring, mm
When radial internal clearances other than CN are
used, refer to Table 19.
　　　　　　d i　 ：Bore diameter of hollow shaft, mm
F
2 Amount of shrinkage of the bore diameter of outer ring
Table 18 Radial internal clearances of Needle Roller Bearings unit: μm
・With steel housing（D 0 ＝∞）
d
Nominal bore diameter
Classification of clearances Table 19 Examples of selecting radial internal
clearances other than CN clearance
　　　∆ E ＝ ∆ De　
E
        ………………………………(27)
G
mm C2 CN C3 C4 C5 D
Over Incl. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Operating conditions Selection of clearance
・With steel housing（D 0 ≠∞）
─ 10 0 25 20 45 35 60 50 75 ─ ─
10 24 0 25 20 45 35 60 50 75 65 90
When heavy loads and shock loads are
applied, and amount of interference is great. 　　　∆ E ＝ ∆ De 　
E
       
1 − (D/D 0) 2
D 1 − (E/D ) 2 (D/D 0) 2
  ……(28) H
24 30 0 25 20 45 35 60 50 75 70 95
30 40 5 30 25 50 45 70 60 85 80 105 When directionally indeterminate loads are applied,
and a tight fit is required for both inner and outer rings. 　　where,　∆ D e ：Effective interference of outer ring, mm
40 50 5 35 30 60 50 80 70 100 95 125 C3 or larger clearance 　　　　　　D ：Outside diameter of outer ring, mm
50
65
65
80
10
10
40
45
40
40
70
75
60
65
90
100
80
90
110
125
110
130
140
165
When temperature of inner ring is much
higher than that of outer ring.
　　　　　　E ：Bore diameter of outer ring, mm
　　　　　　D 0 ：Outside diameter of housing, mm
I
80 100 15 50 50 85 75 110 105 140 155 190 When shaft deflection and/or mounting
100 120 15 55 50 90 85 125 125 165 180 220 error to the housing are great. Reduction of radial clearances due to
J
120 140 15 60 60 105 100 145 145 190 200 245
When less noise and vibration are required. temperature differences between inner
140 160 20 70 70 120 115 165 165 215 225 275
When a loose fit is required for both inner and outer rings. C2 or smaller clearance and outer rings
160 180 25 75 75 125 120 170 170 220 250 300
When preload is required.
180 200 35 90 90 145 140 195 195 250 275 330 Frictional heat generated by rotation is dissipated
200 225 45 105 105 165 160 220 220 280 305 365 through the shafts and housings as well as through oil
225
250
250
280
45
55
110
125
110
125
175
195
170
190
235
260
235
260
300
330
330
370
395
440
Reduction of radial clearances by fit and air. Under general operating conditions, heat dis- K
sipation is larger on the housing side compared with
280 315 55 130 130 205 200 275 275 350 410 485 When the inner or outer rings are interference fitted that on the shaft side, and the temperature of the
315 355 65 145 145 225 225 305 305 385 455 535 onto shafts and into housings, respectively, they outer ring is usually lower than that of the inner ring.
355
400
400
450
100
110
190
210
190
210
280
310
280
310
370
410
370
410
460
510
510
565
600
665
expand or shrink due to elastic deformation. As the
result, the radial clearances are reduced. These
During operation, the temperature of the rolling ele-
ments is the highest, followed by that of the inner ring
L
450 500 110 220 220 330 330 440 440 550 625 735 reduced radial clearances are called residual (inter- and that of the outer ring. The amount of thermal
Remark 　For bearings with CN clearance, no symbol is attached to the identification number. In the case of bearings with C2, C3, C4 and C5 nal) clearances. expansion, therefore, varies, and the radial clearances
clearances, these symbols are attached to the identification number.

M
The amount of reduction is obtained by the following are reduced. This reduced radial clearance is called
　　　　 Example　NA　4905　C2
equation, and it is generally 70 to 90% of the interfer- the effective (internal) clearance, and the amount of
ence amount. reduction is obtained by the following equation:

1N=0.102kgf=0.2248lbs.
A37 1mm=0.03937inch
A38
　　　∆ δ＝ α∆ t E …………………………………(29)
Fit Conditions for determination of fit as ∆ T, the temperature difference between the inner
ring and the shaft can be estimated to be (0.1 〜 0.15)
A
　　where, ∆ δ ： Reduction of radial clearance, mm When determining a suitable fit for a bearing, it is nec- ∆ T. Accordingly, the amount of reduction of the inner
α ： Coefficient of linear expansion for Purpose of fit essary to consider various conditions such as nature ring interference is obtained by the following equation.

B
bearing steel and magnitude of the load, temperature, required
To achieve the best performance of needle roller   ∆ dT ＝ (0.1 〜 0.15) ∆ T α d ≒ 0.0015 ∆ T d ×10 -3 …(32)
　　　　　　　　　　　　　 ≒ 12.5 × 10-6 1/ °C rotational accuracy, material/finish grade/thickness of
bearings, it is important that the bearing rings are cor-
∆ t ： Temperature difference between the the shaft and housing, ease of mounting and dis- 　　where, ∆ dT ： Reduction amount of inner ring
rectly fitted onto the shaft and into the housing.
outer ring and the inner ring plus rolling mounting, etc. interference due to temperature
The purpose of fit is to provide the appropriate
elements considered as one unit, °C
C
amount of interference required between the inner difference, mm
E ： Bore diameter of outer ring, mm 1  Nature of load and fit
ring and the shaft or between the outer ring and the ∆ T ： Temperature difference between
Basically, the appropriate fit depends on whether the
housing, to prevent harmful mutual slippage. the inside of the bearing and the
The temperature difference ∆ t is considered to be 5 load direction is rotational or stationary in relation to
If the interference is insufficient, it will cause a harmful outside of the housing, °C
〜 10°C under normal operating conditions and 15 〜 the inner and outer rings.
relative displacement, known as creep, between the α ： Coefficient of linear expansion
20°C at high rotational speeds. Therefore, when the
temperature difference is great, a correspondingly
fitted surfaces in the circumferential direction. This
may lead to abnormal wear of fitted surfaces, intru-
The relationship between the nature of radial loads
and the fit is, in general, based on Table 20. for bearing steel D
larger radial internal clearance must be selected. ≒ 12.5×10-6 1/ °C
sion of wear particles into the bearing, generation of
2  Load amount and interference d ： Bore diameter of inner ring, mm
abnormal heat, vibration, etc. Therefore, a suitable fit
The greater the load, the larger the interference must
must be selected.
be. 4  Shaft finish grade and interference
Since peaks of surface roughness of the fitted surface
E
When selecting an interference between the inner ring
Table 20 Nature of radial load and fit and the shaft, it is necessary to estimate the reduction are crushed down when fitting the bearing, the effec-
of interference due to the radial load. The amount of tive interference becomes smaller than the apparent
Fit
Nature of the load
Rotating conditions Inner ring Outer ring
reduction of interference is obtained by the following
equations.
interference obtained by measurements, and it is gen-
erally obtained by the following equations.
F
・For ground shaft
Inner ring : Rotating ・When F r ≦ 0.2C 0
d
Outer ring : Stationary
Load direction : Fixed 　　　∆ dF ＝ 0.08 d F ×10 ………………(30)
　     r
-3
　　 　∆ de ＝　　　  ∆ df   …………………………(33)
d＋2 G
B ・For machined shaft
Rotating load on inner ring Interference fit Clearance fit
Stationary load on outer ring ・When F r>0.2C 0
d
　　 　∆ de ＝　　　  ∆ df   …………………………(34)
Inner ring : Stationary
Outer ring : Rotating
Fr
　　　∆ dF ＝ 0.02       × 10
B
-3     
……………………(31)
d＋3
H
Load direction : Rotating with outer ring 　　where, ∆ de ： Effective interference of inner ring,
　　where, F r ：Radial load applied to bearing, N mm
C0 ：Basic static load rating, N d ： Bore diameter of inner ring, mm
I

∆ dF ：Amount of reduction of inner ∆ df ： Apparent interference, mm

Inner ring : Stationary ring interference, mm
Outer ring : Rotating d ：Bore diameter of inner ring, mm 5  Minimum interference and maximum interference
Load direction : Fixed
B ：Width of inner ring, mm When the load direction is rotating in relation to the
Rotating load on outer ring
Stationary load on inner ring
Clearance fit Interference fit
inner ring, the inner ring is fitted with interference to
the shaft.
J
3  Temperature conditions and change of interference
The interference of fitted surfaces is also influenced For solid ground steel shafts, the minimum interfer-
Inner ring : Rotating
by the temperature difference between the bearing e n c e ( r e q u i r e d a p p a r e n t i n t e r fe r e n c e ) ∆ d f i s
Outer ring : Stationary
Load direction : Rotating with inner ring and the shaft and housing. For example, when steam
is flowing through a hollow shaft, or when the housing
expressed by the following equation which is deduced
from equations (30) or (31), (32) and (33). K
is made of light metal, it is necessary to take into con-
d＋2
The load direction is not sideration the differences in temperature, the coeffi- 　　∆ df ≧　　　  (∆ dF ＋ 0.0015 ∆ T d×10 -3 )  …(35)
d
L
fixed, including cases where Inner ring : Rotating or stationary cient of linear expansion and other such factors.
Directionally indeterminate load the load direction is fluctuat- Outer ring : Rotating or stationary Interference fit Interference fit Usually, the interference of the inner ring decreases It is desired that the maximum interference should be
ing or there is an unbal- Load direction : Not fixed as the bearing temperature increases during opera- less than 1/1000 of the shaft diameter. In the case of
anced load. tion. If the temperature difference between the inside the outer ring, the effective interference varies accord-
of the bearing and the outside of the housing is taken ing to the housing material, thickness, shape, etc., so
it is determined empirically. M

1N=0.102kgf=0.2248lbs.
A39 1mm=0.03937inch
A40
Selection of fit Table 22 Fit between needle roller bearings with inner ring and shafts
A
Shaft dia. mm Tolerance class Application examples
When selecting a suitable fit, in addition to the various Operating conditions
Over Incl. of shaft（1） (Reference)
conditions mentioned above, it is necessary to draw

B
on experience and practical results. Light load, normal load, low or
Tables 21 and 22 show the most general fit data. medium rotating speed
g6
Wheels on dead axles
When a thin housing or a hollow shaft is used, the Control lever gears
Stationary load
interference is made larger than an ordinary fit. Heavy load, medium rotating speed All shaft diameters h6
on inner ring Rope sheaves
The fit between needle roller bearings without inner
ring and shafts is based on Table 23.
For the fit between Shell Type Needle Roller Bearings
Especially smooth operation and
accuracy are required.
h5
Tension pulleys
C
and housing bores, see page B5. − 50 j5 Electric appliances, Precision machinery
For the fit between inner rings for Shell Type Needle Light load
  50 100 k5 Machine tools, Pumps
Roller Bearings and shafts, see Table 22.
Rotating load
on inner ring or
100
200
200
−
m6（2）
n6（3）
Blowers, Transportation vehicles D
Directionally
−  50 k5（ ） 4
General bearing applications
indeterminate Normal load
  50 150 m5，m6（2）
Pumps, Transmission gearboxes,
Table 21 Fit between needle roller bearings and housing bores (Not applicable to Shell Type Needle Roller Bearings) 150 200 n6（3）
E
load Wood working machinery, Internal combustion engines
200 − p6（3）
Tolerance class of
Operating conditions Application examples (Reference)
housing bore（1） Heavy load − 150 n6（3） Industrial vehicles, Construction machinery
Shock load 150 − p6（3） Crushers
Heavy load on thin housing, large
P7（2） Flywheels Notes(1)　This table applies to solid steel shafts.
shock load

Rotating load on
Heavy load, normal load N7（2） Wheel bosses, transmission gears
(2)　It is necessary to examine the reduction of radial internal clearances caused by the expansion of inner rings after mounting.
(3)　It is necessary to use bearings with radial internal clearances greater than CN clearance.
(4)　For NATA and NATB, do not use a tighter fit than k5.
F
outer ring

Light load, fluctuating load M7 Pulleys, tension pulleys Table 23 Tolerance class of shafts assembled with needle roller bearings without inner ring

Large shock load Eccentric wheels, pumps

Fw
Nominal roller set bore diameter
Radial internal clearance
G
M7
mm Smaller than CN clearance CN clearance Larger than CN clearance
Directionally
indeterminate Heavy load, normal load K7 Compressors Tolerance class of shaft（1）
H
Over Incl.
load
　− 65 k5 h5 g6
Normal load, light load J7 Crankshafts, compressors
65 80 k5 h5 f6
80 160 k5 g5 f6

I
Shock load, heavy load J7 General bearing applications, gear shafts 160 180 k5 g5 e6
180 200 j5 g5 e6
Stationary load
Normal load, light load H7 General bearing applications 200 250 j5 f6 e6
on outer ring
250 315 h5 f6 e6
315 − g5 f6 d6
J
With heat conduction through shaft G7 Paper dryers
Note(1)　When the housing bore fit is tighter than K7, the shaft diameter is made smaller by considering shrinkage of roller set bore diameter
Light load, normal load, requirements of high-precision after mounting.
K6 Main spindles of machine tools
rotation and high rigidity
Notes(1)　This table applies to steel or cast iron housings. For lighter metal, a tighter fit should be selected.
For split housings, do not use a fit tighter than J7.
(2)　Care should be taken so that the radial internal clearance is not too small.
Remark 　Light load, normal load and heavy load represent P ≦ 0.06C, 0.06C<P ≦ 0.12C, and 0.12C<P, respectively, where P is the
K
dynamic equivalent radial load and C is the basic dynamic load rating of the bearing to be used.

1N=0.102kgf=0.2248lbs.
A41 1mm=0.03937inch
A42
Table 24 Fit values for radial bearings (JIS Class 0) (Fit with housing bore) unit: μｍ
Design of Shaft and Housing Inclination of shaft
A
D ∆ Dmp G7 H7 J7 K6 K7 M7 N7 P7
Nominal outside Single plane mean Shafts and outer rings may have some inclination
Accuracy and roughness of shaft and housing

Housing

Housing

Housing

Housing

Housing

Housing

Housing

Housing
diameter outside diameter between them due to deflection of the shaft, machin-

B
mm deviation ing accuracy of shafts and housings, errors in mount-
Bearing Bearing Bearing Bearing Bearing Bearing Bearing Bearing
Accuracy and roughness of fitting surface
ing, etc.
Over Incl. High Low
In this case, the use of two or more bearings in tan-
3 6 0 - 8 - 24 〜 - 4 - 20 〜 0 -14 〜 6 -10 〜 6 -11 〜 9 -  8 〜 12 -  4 〜 16 0 〜 20 Since the bearing rings of needle roller bearings are
dem arrangement on a single shaft should be avoid-
6 10 0 - 8 - 28 〜 - 5 - 23 〜 0 -16 〜 7 -10 〜 7 -13 〜 10 -  8 〜 15 -  4 〜 19 1 〜 24 thin, their performance is easily affected by poor
ed. Instead, a bearing with large load ratings should
10
18
18
30
0
0
- 8
- 9
- 32 〜
- 37 〜
- 6
- 7
- 26 〜 0
- 30 〜 0
-18 〜 8
-21 〜 9
-10 〜 9
-11 〜 11
-14 〜 12
-15 〜 15
-  8 〜 18
-  9 〜 21
-  3 〜 23
-  2 〜 28
3 〜 29
5 〜 35
accuracy of shafts or housings. Under general oper-
ating conditions, the fitting surfaces of shafts and
be used.
It is recommended that inclination of shafts be less
C
30 50 0 -11 - 45 〜 - 9 - 36 〜 0 -25 〜 11 -14 〜 13 -18 〜 18 -11 〜 25 -  3 〜 33 6 〜 42 housings can be finished by lathe turning. However,
than 1/1000.
50 80 0 -13 - 53 〜 -10 - 43 〜 0 -31 〜 12 -17 〜 15 -22 〜 21 -13 〜 30 -  4 〜 39 8 〜 51 when the load is great and high accuracy and low
- 62 〜 - 50 〜 0 -37 〜 13 -19 〜 18 -25 〜 25 -15 〜 35 -  5 〜 45 9 〜 59 noise are required, a grinding finish is required.
D
80 120 0 -15 -12 Table 27 Tolerance class IT values for basic
120 150 0 -18 - 72 〜 -14 - 58 〜 0 -44 〜 14 -22 〜 21 -30 〜 28 -18 〜 40 -  6 〜 52 10 〜 68 Table 26 shows the accuracy and roughness of fitting
dimensions
150 180 0 -25 - 79 〜 -14 - 65 〜 0 -51 〜 14 -29 〜 21 -37 〜 28 -25 〜 40 -13 〜 52 3 〜 68 surfaces for general use.
Basic dimension Tolerance class（1）
180 250 0 -30 - 91 〜 -15 - 76 〜 0 -60 〜 16 -35 〜 24 -43 〜 33 -30 〜 46 -16 〜 60 3 〜 79
mm IT5 IT6 IT7
250 315 0 -35 -104 〜 -17 - 87 〜 0 -71 〜 16 -40 〜 27 -51 〜 36 -35 〜 52 -21 〜 66 1 〜 88 Accuracy and roughness of raceway surface
315
400
400
500
0
0
-40
-45
-115 〜
-128 〜
-18
-20
- 97 〜 0
-108 〜 0
-79 〜 18
-88 〜 20
-47 〜 29
-53 〜 32
-57 〜 40
-63 〜 45
-40 〜 57
-45 〜 63
-24 〜 73
-28 〜 80
1 〜 98
0 〜 108 In case of needle roller bearings unlike other bear-
Over
　−
Incl.
3 4
Tolerance　μｍ
6 10
E
Remark　The negative value denotes a clearance and the positive value denotes an interference. ings, mating surfaces such as shaft and housing bore 3 6 5 8 12
surfaces can be used directly as the raceway sur- 6 10 6 9 15

F
faces. For such use, accuracy and roughness of the 10 18 8 11 18
Table 25 Fit values for radial bearings (JIS Class 0) (Fit with shaft)　         unit: μｍ raceway surfaces are important because they will 18 30 9 13 21
d ∆ d mp g6 h5 h6 j5 k5 m5 m6 n6 p6 influence bearing life, noise and accuracy. 30 50 11 16 25
Nominal bore Single plane mean In general, accuracy and roughness of raceway sur- 50 80 13 19 30
Bearing

Bearing

Bearing

Bearing

Bearing

Bearing

Bearing

Bearing

Bearing
diameter bore diameter faces are based on Table 26. 80 120 15 22 35
mm deviation
Over Incl. High Low
Shaft Shaft Shaft Shaft Shaft Shaft Shaft Shaft Shaft
120
180
180
250
18
20
25
29
40
46
G
250 315 23 32 52
3 6 0 -  8 -12 〜 4 -  5 〜 8 -  8 〜 8 -  2 〜 11 1 〜 14 4 〜 17 4〜 20 8〜 24 12 〜 28
315 400 25 36 57
6 10 0 -  8 -14 〜 3 -  6 〜 8 -  9 〜 8 -  2 〜 12 1 〜 15 6 〜 20 6〜 23 10 〜 27 15 〜 32
10
18
18
30
0
0
-  8
-10
-17 〜
-20 〜
2
3
-  8 〜 8
-  9 〜 10
-11 〜 8
-13 〜 10
-  3 〜 13
-  4 〜 15
1 〜 17
2 〜 21
7 〜 23
8 〜 27
7〜
8〜
26
31
12 〜
15 〜
31
38
18 〜
22 〜
37
45
400
500
500
630
27
30
40
44
63
70 H
Note(1)　Based on JIS B 0401.
30 50 0 -12 -25 〜 3 -11 〜 12 -16 〜 12 -  5 〜 18 2 〜 25 9 〜 32 9〜 37 17 〜 45 26 〜 54
50 80 0 -15 -29 〜 5 -13 〜 15 -19 〜 15 -  7 〜 21 2 〜 30 11 〜 39 11 〜 45 20 〜 54 32 〜 66
80
120
120
140
0 -20 -34 〜 8 -15 〜 20 -22 〜 20 -  9 〜 26 3 〜 38 13 〜 48 13 〜 55 23 〜 65 37 〜 79 Table 26 Specifications of shafts and housings for radial needle roller bearings
Shaft Housing bore
I
140 160 0 -25 -39 〜 11 -18 〜 25 -25 〜 25 -11 〜 32 3 〜 46 15 〜 58 15 〜 65 27 〜 77 43 〜 93 Item
160 180 Fitting surface Raceway surface Fitting surface Raceway surface

180 200 0.3 × IT6（1） 0.3 × IT6（1） 0.3 × IT7（1） 0.3 × IT7（1）
200
225
225
250
0 -30 -44 〜 15 -20 〜 30 -29 〜 30 -13 〜 37 4 〜 54 17 〜 67 17 〜 76 31 〜 90 50 〜 109 Circularity or
0.3 × IT5（1）
or
0.3 × IT5（1）
or
0.3 × IT6（1）
or
0.3 × IT6（1） J
250 280 0.5 × IT6（2） 0.3 × IT6（1） 0.5 × IT7（2） 0.3 × IT7（1）
0 -35 -49 〜 18 -23 〜 35 -32 〜 35 -16 〜 42 4 〜 62 20 〜 78 20 〜 87 34 〜 101 56 〜 123 Cylindricity or or or or
280 315
0.5 × IT5（2） 0.3 × IT5（1） 0.5 × IT6（2） 0.3 × IT6（1）
315
355
355
400
0 -40 -54 〜 22 -25 〜 40 -36 〜 40 -18 〜 47 4 〜 69 21 〜 86 21 〜 97 37 〜 113 62 〜 138
Surface roughness μ mRa 0.8 0.2（3） 1.6 0.2（3） K
400 450 　　  　　 　   （μ mRy） (3.2) (0.8) (6.3) (0.8)
0 -45 -60 〜 25 -27 〜 45 -40 〜 45 -20 〜 52 5 〜 77 23 〜 95 23 〜 108 40 〜 125 68 〜 153
450 500

L
Remark　The negative value denotes a clearance and the positive value denotes an interference.
Hardness − 58 〜 64HRC（4） − 58 〜 64HRC（4）

Notes(1)　30% or less of the dimensional tolerance for shafts or housing bores is recommended.
(2)　50% or less of the dimensional tolerance for shafts or housing bores is recommended.
(3)　When required accuracy is not critical, a surface roughness within 0.8 μmRa (3.2 μmRy ) is allowable.

M
(4)　An appropriate thickness of the hardened layer is required.
Remark　 For tolerance class IT, see Table 27.

1N=0.102kgf=0.2248lbs.
A43 1mm=0.03937inch
A44
Raceway materials and heat treatment Dimensions related to mounting of bearings Table 28 Largest permissible single corner radius
of shafts and housings  r as max
entry of harmful foreign substances, such as dirt, dust
and water. For this reason, sealing devices must
A
When using shafts and housings as raceways, the fol- The dimensions of shaft and housing related to unit: mm always work effectively to seal and prevent against
lowing materials are generally used. mounting of the needle roller bearings are shown in r s min r as max dust penetration under all operating conditions. Also,

B
　High-carbon chromium bearing steel the table of dimensions for each bearing. (See Fig. Smallest permissible Largest permissible single when selecting a suitable sealing method, it is neces-
single chamfer corner radius of shafts and
SUJ2 JIS G 4805 13.) sary to consider such factors as the type of lubricant,
dimension housings
　Carburizing steel SCM415 〜 421   JIS G 4053 The minimum value of the shaft shoulder diameter d a peripheral speed of the seal, operating temperature,
which receives the inner ring, and the maximum value 0.1 0.1 shaft eccentricity, seal friction, etc. as well as ease of
　Carburizing steel SNCM 220 JIS G 4053 rs min Housing
of the housing shoulder diameter D a which receives 0.15 0.15

rs min
　Carburizing steel assembly and disassembly.
C
SCr 420 JIS G 4053 ras max
the outer ring, represent the effective shoulder diame- 0.2 0.2 Sealing methods are of the non-contact and contact
　Carburizing steel SNC 415、815 JIS G 4053 0.3 0.3
ters (excluding the chamfered part) which make prop- types, and it is necessary to select the appropriate
　Carburizing steel S 15 CK JIS G 4051 0.4 0.4
er contact with the side faces of the inner and outer type depending on the application.
In addition, S50C and S55C (JIS G 4051) can be 0.6 0.6
rings respectively.
used after through hardening or induction hardening. 1 1
The hardened layer produced by tempering at +160
Also, the maximum value of the shaft shoulder (or
1.1 1 ras max Non-contact type sealing method D

rs min
inner ring retaining piece) diameter d a is the dimen- 1.5 1.5
rs min
〜 +180°C after hardening must have a fine uniform
sion related to the ease of mounting/dismounting of 2 2 Shaft There are many methods of non-contact type sealing,
martensite microstructure.
the shaft and inner ring to/from the housing and outer 2.1 2 including the use of oil grooves, flingers and
When hardening the raceway surface by case hard-
ring.
E
2.5 2 labyrinths, which utilize the centrifugal force and nar-
ening or induction hardening, a surface hardness of
The largest permissible single corner radius r as max of 3 2.5 row gaps.
58 〜 64HRC and an appropriate thickness of the
the shaft and housing must be smaller than the small- 4 3 Since they do not make direct contact with the shaft
hardened layer must be ensured. The minimum
est permissible single chamfer dimension r s min of the 5 4 or housing, it is unnecessary to consider friction and
effective thickness of the hardened layer after heat
bearing so that the side surface of the bearing can wear, and the non-contact sealing method is suitable

F
treatment and grinding is defined as the distance from
make proper contact with the shoulder. Table 28 Table 29 Fillet relief dimensions for ground shafts for high speed rotation and high operating tempera-
the surface to the depth where the hardness is
shows the related dimensions. and housings  unit: mm tures. However, because of gaps, this method is not
550HV, and it is obtained by the following equation.
For dimensions of the fillet relief when finishing the r s min always sufficient in preventing oil leakage and dust
　　　
Eht ≧ 0.8Dw(0.1 ＋ 0.002D w) ……………(36) shaft or housing by grinding, the values shown in Smallest permissible Fillet relief dimensions entry when the machine is not in operation.

G
Table 29 are recommended. single chamfer
　　where,　E ht ：M inimum effective thickness of For other dimensions related to mounting, see the dimension t r gs b 1  Oil groove
the hardened layer, mm related section for each bearing as required. 1 0.2 1.3   2 Oil grooves are provided on either the shaft or hous-

rgs
h
　　　　D w：Roller diameter, mm

t
In addition, for ease in dismounting of bearings, it is 1.1 0.3 1.5   2.4 ing bore, or on both for more effective sealing (See
Generally, the required effective thickness of the convenient to make notches in the shoulder of the 1.5 0.4 2   3.2 Fig. 14.). The clearance between the shaft and the
hardened layer is at least 0.3 mm. shaft or housing to allow the insertion of dismounting
hooks.
2
2.1
0.5
0.5
2.5
2.5
  4
  4
rs min

b
housing bore should be as small as possible, and the
values shown in Table 30 are generally used, taking
H
3 0.5 3   4.7
into consideration errors in machining and assembly,
4 0.5 4   5.9
shaft deformation, etc. Three or more grooves are
5 0.6 5   7.4
6
7.5
0.6
0.6
6
7
  8.6
10
made with a width of 3 〜 5 mm and a depth of 4 〜 5
mm. If the grooves are filled with grease, it will be I
more effective for dust prevention.
As shown in Fig. 15, helical grooves are suitable for
Sealing horizontal shafts which have a fixed direction of rota-

To obtain the best performance of rolling bearings, it

tion. Right or left handed grooves are used according J
Da
da

to the direction of rotation, and they are used for oil

is necessary to prevent leakage of lubricant and the lubrication normally in conjunction with a suitable anti-
dust device.

K
Fig. 13 Dimensions related to mounting

M
(1) (2) (3)
Fig. 14

1N=0.102kgf=0.2248lbs.
A45 1mm=0.03937inch
A46
Table 30 Clearance between grooved shaft and
housing bore unit: mm
3  Labyrinth
Although it is a little difficult to make, the labyrinth is
Contact type sealing method Table 33 Peripheral speed and surface roughness
of shaft A
very effective in preventing oil leakage especially at In this type of sealing, the shaft is sealed by the appli- Peripheral speed  m ／ s Surface roughness
Shaft dia. Clearance
high speeds. At low speeds, filling the labyrinth with cation of pressure resulting from the elasticity of the Over Incl. μ mRa ( μ mRy)

B
Incl. 50 mm 0.25 〜 0.4 grease is effective in preventing the entry of dust. In seal material to the sealing surface of the shaft, which −   5 0.8(3.2)
Fig. 17, it is necessary to split the housing or cover rotates, reciprocates or oscillates. Synthetic rubber,
Over 50 mm 0.5 〜 1   5 10 0.4(1.6)
plate into two. In Fig. 18, it is easy to assemble, and synthetic resin and felt are generally used as sealing
10 − 0.2(0.8)
if combined with an oil seal, it improves the sealing materials.
effect.
Table 31 shows the labyrinth clearances generally
used.
1  Oil seal
Synthetic rubber oil seals are the most general type of
2  Felt seal
Because of their simple structure, felt seals have long
C
sealing used. The sealing effect is obtained when the been used to protect grease lubrication from dust.
elastic lip comes into contact with the shaft. Some Since felt absorbs some grease during operation, it

Fig. 15
lips are spring-loaded to maintain adequate pressing
force.
hardly causes heat generation and seizure, but it can-
not be used when the peripheral speed of the shaft is D
The sliding surfaces of the lip and the shaft always high (more than 4 m/s). Where there is a high con-
show frictional behavior such that the boundary lubri- centration of dirt and dust, they may become attached
cation and fluid lubrication are mixed. If there is an to the contact surface of felt, sometimes scratching
2  Flinger
The oil flinger is a disk attached to the shaft which
(1)
insufficient amount of oil between the contact sur- the shaft surface. To prevent this, two felt seals are E
throws off oil due to the centrifugal force of rotation faces, it will cause heat generation, wear and seizure. placed apart from each other, or a felt seal is used
and thus prevents oil leakage and the entry of foreign Conversely, if the oil film is too thick, it may cause oil together with a synthetic rubber seal.
particles. Fig. 16 (1) shows an example in which the leakage.
flinger is located inside the housing, mainly to prevent
oil leakage. Since it sucks in dust and dirt, it should
General oil seals are specified in JIS B 2402-1~5.
Oil Seals for Needle Roller Bearings (See page
F
be used in a dust free environment. Fig. 16 (2) shows L1.) have a low sectional height to match the Needle
an example in which the flinger is located outside the Roller Bearings.

G
housing, and is used in combination with another Nitrile rubber is generally used as the material for oil
(2)
sealing device, to prevent entry of foreign particles. seal lips. Table 32 shows the materials and their
operating temperature ranges.
The finished surface of the shaft where the seal lip
Fig. 17 makes contact must have an appropriate surface
roughness, as shown in Table 33, according to the
peripheral speed. It must also have accurate circular-
H
ity, and the shaft eccentricity should be less than 0.05
(1) mm.
To increase wear resistance, the hardness of the slid-
ing part of the shaft must be more than 40HRC. This I
can be achieved by hard-chrome plating or heat treat-
ment.

(2)
Fig. 18
Table 32 Seal materials and operating temperatures J
Fig. 16
Seal material Operating temperature range ℃
Table 31 Labyrinth clearance unit: mm

Shaft dia.
Clearance
Nitrile rubber
Acrylic rubber
− 25 〜＋ 120
− 15 〜＋ 130
K
Radial direction Axial direction Synthetic rubber
Silicon rubber − 50 〜＋ 180
Incl. 50 mm 0.25 〜 0.4 1〜2
Fluoro rubber − 10 〜＋ 180
Over 50 mm 0.5 〜 1 3〜5
Tetrafluoethylene resin − 50 〜＋ 220
L

1N=0.102kgf=0.2248lbs.
A47 1mm=0.03937inch
A48
Lubrication Methods of lubrication Grease lubrication 2  Replenishment of grease
The life of grease depends on its type and quality, the
A
Grease lubrication and oil lubrication are generally 1  Amount of grease to be filled type and dimensions of the bearing, operating condi-
Purpose of lubrication used for rolling bearings. In special cases, solid lubri- The amount of grease to be filled depends on the tions, temperature, amount of wear, penetration of for-

B
cants are also used. housing structure, dimensions, type of grease used eign particles and water, etc.
The main purpose of bearing lubrication is to reduce
In general, grease lubrication requires the simplest and atmosphere. Generally, filling about 1/3 to 1/2 of Fig. 20 shows the replenishment intervals for grease,
friction and wear and to prevent heat generation and
sealing device. It is therefore economical, and widely the free space inside of the bearing and the housing and is used as a general guideline. The values
seizure. The lubricant and the lubricating method
used. Also, once filled with grease, the bearing can is considered to be appropriate. Too much will cause obtained from this diagram apply to cases in which
have a big influence on the operating performance of
be used for a long period without replenishing the a rise in temperature, and care should be taken espe- the load condition is normal, the machine body is sta-
C
the bearing, and it is therefore necessary to select
grease. However, compared with oil, its heat removal cially at high speed rotations. tionary, and the operating temperature on the outer
them suitably for the operating conditions.
properties and cooling capacity are inferior, since In Fig. 19, several grease pockets are provided by the surface of bearing outer ring is less than +70°C. If
The effects of lubrication are as follows.
grease has high flow resistance, which causes high grease sectors on one side of the bearing. Even if the the temperature exceeds +70°C, as a general rule,
churning heat. filled grease is dispersed by the centrifugal force at the replenishment interval is halved for every 15°C
1  Reduction of friction and wear
At the contact surfaces between the race rings, rolling
elements and cage of the bearing, lubrication pre-
Oil has greater fluidity and superior heat removal
properties. It is therefore suitable for high-speed
high rotational speeds, it is trapped by the grease
pockets and diverted back into the bearing again. Old
increase.
D
operations. In addition, it is simple to filter out dust grease accumulates in the space on the opposite side
vents metal-to-metal contact, and reduces friction and
and dirt from oil. Thus it can prevent the generation of the bearing, and this can be removed periodically
wear due to sliding and rolling, in the latter of which
of noise and vibration and increase bearing life.
E
micro-slips occur by differential slip, skew, spin, or by taking off the cover.
Another advantage of oil lubrication is that it offers the
elastic deformation.
possibility for selecting the appropriate method for
particular operating conditions from among various
2  Elimination of frictional heat available lubrication methods. However, measures to
The lubricant removes the heat generated by friction
or transferred from outside, and prevents overheating
prevent oil leakage are required. As a guideline for
selection, Table 34 compares grease and oil lubrica-
F
of the bearing. Circulating lubrication is generally
tion.
used for this purpose.
For the lubricants used for Spherical Bushings,

G
see page K8.
3  Influence on bearing life
The bearing life is extended if the rolling contact sur-
faces between the race rings and rolling elements are Table 34 Comparison between grease lubrication Fig. 19
separated by an oil film of adequate thickness, and is and oil lubrication

H
shortened if the oil film is inadequate due to low oil
Item Grease lubrication（1） Oil lubrication 20000
viscosity, etc.
15000
Sealing,
4  Rust prevention Simple Slightly complicated 10000
Housing structure
The lubricant prevents rust formation on the inside 8000

and outside surfaces of the bearing. High temperature allowed 6000

I

hours
Temperature High temperature not allowed
(Cooling effect by circulation) 5000

d ＝ 20
4000

10
m
5  Dust prevention

m
tf
Rotational speed Low and medium speeds High speed allowed 3000
Grease lubrication is particularly effective for dust pre-

30 0
Replenishment interval for grease,

4
J

50 0
6
2000
vention. Oil circulating or jet lubrication is effective in

80
10
120
140

0
Load Low and medium loads High load allowed

1600
washing foreign particles away from the area around 1500

18
200
240
280
300
the bearing. 1000
Elaborate
Maintenance Easy 800
(Pay special attention to oil leaks. )

K
600
500
Lubricant replacement Slightly complicated Simple 400

300

Lubrication performance Good Very good 200 Remark　

200 400 600 1000 2000 4000 6000 10000

L
d is the bore diameter of the inner ring. For a
Rotational speed, n min-1 bearing without an inner ring, the roller set bore
Dust filtration Difficult Simple
diameter F w is used for d .

Dust and dirt can be removed by Fig. 20 Interval for replenishment of grease
Entry of dust and dirt Easy measures for protection
filtering in circulating lubrication.
Note(1)　This represents bearing grease for general use. M

1N=0.102kgf=0.2248lbs.
A49 1mm=0.03937inch
A50
Oil lubrication oil flows along the grooves in the case and accumu-
lates in the oil pockets, keeping the oil level constant.
the bearing rotates together with the bearing forming
an air wall. As shown in Fig. 24, the jet from the noz-
Lubricants A
1  Oil bath lubrication So the oil is steadily supplied to the bearing. zle blows directly into the space between the inner For rolling bearings, lubricating grease or oil is gener-
This is the most commonly used oil lubrication ring and the cage. Due to the large amount of oil ally used. For special applications, solid lubricants

B
method, and is used for medium and low speeds. If being used, it is more effective to make the discharge are used.
the amount of oil is too large, heat will be generated port larger, and use the forced discharge.
by churning, and if the amount is too small, seizure When the d m n value (mean value of the bearing out- Lubricating grease
will occur. Therefore, the correct amount of oil must side and bore diameters in millimeter x rotational
be maintained. When the machine is stationary, the speed in min-1) is more than 1,000,000, the speed of Grease is a semi-solid lubricant made by mixing base
correct oil level in the case of a bearing mounted on a
horizontal shaft, is near the center of the lowest rolling
the jet should be 10 〜 20 m/s, the nozzle diameter
should be about 1 mm, oil supply pressure should be
oil (liquid lubricant) and a thickener under heat and
adding additives as required.
C
element. In the case of a vertical shaft, about 50% of 0.1 〜 0.5 MPa, and the oil supply amount should be There are many types of grease according to various
the surfaces of the rolling elements should be sub- about 500 cc/min or greater. When the rotational combinations of base oil, thickeners and additives.
Fig. 22 Oil splash lubrication
merged in oil.
It is desirable to provide an oil gauge so that the oil
speed is higher, the oil supply pressure and the oil
amount should be higher.
Grease is usually classified by thickeners and base
oil. Table 35 shows the general properties of each D
level can be easily checked while the machine is sta- 4  Oil circulating lubrication type of grease.
tionary or running. When automatic lubrication is more economical
because lubrication is required at many points, or
2  Oil drip lubrication when cooling is required for high rotational speed, this
method is used. The oil is supplied with a pump,
E
Oil drips, which are fed down from a sight-feed oiler or
along a fiber string, become an oil spray due to wind which can control the oil pressure, and a filter or cool-
pressure generated by the rotating cage, shaft, nut, er, etc. can be set up in the circulation system, mak-
etc., or they strike the rotating parts and form an oil
spray, which fills up the housing and every required
ing this an ideal method of lubrication. As shown in
Fig. 23, the oil supply and discharge ports are located F
part. Because oil spray removes frictional heat, this opposite to each other, and the discharge port is
method has a more effective cooling effect than the oil made large to prevent the accumulation of oil.
Fig. 24 Oil jet lubrication

G
bath method, and is widely used for high-speed rota-
tion and medium load conditions.
In the case of the sight-feed oiler (Fig. 21), the num- Table 35 Properties of various types of grease
ber of drips can be adjusted. However, this is difficult Name (Common name) Calcium Sodium Aluminum Mixed base Barium Non-soap base grease
grease grease grease grease grease Lithium grease
using the string-feed method. The number of drips (Non-soap grease)
depends on the bearing type, rotational speed, etc.,
but 5 〜 6 drips per minute is generally used. Item （　　）
grease （　　）
Cup
grease （　　）
Fiber Mobile
grease （　　）
grease （　　）
grease （　　）
Diester
grease
Silicon Bentone H
Base oil Mineral oil Mineral oil Mineral oil Mineral oil Mineral oil Mineral oil Diester oil Silicon oil Mineral oil Synthetic oil

Na + Ca soap, Silica gel.

Ca soap
I
Thickener Na soap Al soap Ba soap Li soap Li soap Li soap Bentone Polyurea,
Fig. 23 Oil circulating lubrication Li + Ca soap etc.
Fibrous and Stringy and Fibrous and Fibrous and
Appearance Buttery Buttery Buttery Buttery Buttery Buttery
buttery buttery buttery buttery
5  Oil mist lubrication
After dirt and dust are removed by a filter, the oil is Pour point ℃ 80 〜 90 150 〜 180 70 〜 90 160 〜 190 150 〜 180 170 〜 190 170 〜 190 200 〜 250 200 〜 None
turned into a spray by dry compressed air, and this
lubricates the bearing. When the air and oil pass
Operating temperature range ℃ − 10 〜＋ 70 − 20 〜＋ 120 − 10 〜＋ 80 − 10 〜＋ 100 − 10 〜＋ 135 − 20 〜＋ 120 − 50 〜＋ 120 − 50 〜＋ 180 − 10 〜＋ 150 〜＋ 200 J
Pressure resistance Strong to weak Strong to medium Strong Strong Strong to medium Medium Medium Weak Medium to weak Medium
Fig. 21 Oil drip lubrication through the bearing, the air cools the bearing and the
Good, poor for Na+
oil lubricates it. In addition, because the air inside the Water resistance Good Poor Good Good Good Good Good Good Good
Ca soap grease
3  Oil splash lubrication
In this method, oil is splashed in all directions by the
housing is at a higher pressure than the outside air,
the entry of water and foreign particles is prevented. Mechanical stability Fair Good Poor Good Poor Excellent Excellent Excellent Good Good to poor K
rotation of the gear or disk. This can be used for con- There are many other advantages of this method, and Contains about Long fibrous It has water Usable at fairly It has water This is the best Excellent Mainly used Generally good heat resis-
siderably high-speed rotations without soaking the it is suitable for high rotational speed applications 1% water. grease cannot and rust resis- high speeds. and heat resis- all-purpose under low for high tem- tance. Grease having a miner-
When the tem- withstand high tant proper- tant proper- grease among temperature peratures. Not al base oil is for general use.
bearing directly in oil. such as high speed internal grinding spindles.
L
perature rises speeds, but ties, and ties. This is an soap based conditions and suited to high Grease having a synthetic base
In the gear case where shafts and bearings are lubri- to more than has good pres- adheres easily all-purpose greases. has superior speeds and oil is suitable for special use
+80°C, the sure resis- to metal sur- grease. frictional prop- heavy loads. where superior heat and chem-
cated with the same oil, wear particles may be intro- 6  Oil jet lubrication Features and application water evapo- tance proper- face. erties. ical resistance properties are
duced into the bearing as they might get mixed with This is a highly reliable lubrication method and is used rates and the ties. Short Suitable for required.
grease sepa- fibrous grease small bearings
the oil. In this case, a permanent magnet is provided under severe conditions such as ultra-high rotational rates into oil is compara- used in mea-
at the bottom of the gear case to collect metal parti-
cles, or a shield plate is installed next to the bearing.
speeds and high temperatures. The speed of the oil
jet should be more than 20% of the peripheral speed
and soap. This
is used for
medium loads.
tively good for
high speeds.
suring instru-
ments. M
Fig. 22 shows another method in which the splashed of the inner ring raceway surface, since the air around

1N=0.102kgf=0.2248lbs.
A51 1mm=0.03937inch
A52
 1  Base oil
Petroleum lubricating oil is usually used as the base
running for long periods of time, its temperature rises.
This results in oxidation of the lubricant and formation Redwood Saybolt
(sec) (sec)
Centi
strokes
A
oil. of oxides, which lead to corrosion of the bearing. ISO viscosity grade
2000 (Viscosity index 80)
As the lubricating performance of grease depends Thus, when a bearing is to be operated for long peri- 5000 5000 1000 A : VG 7 H ： VG100

B
mainly on that of base oil, the viscosity of the base oil ods of time without regreasing, antioxidants are 500 B ： VG10 J ： VG150
2000 2000 C ： VG15 K ： VG220
is an important property. In general, low viscosity is added. In addition, grease containing extreme pres- 1000
300
1000 200 D ： VG22 L ： VG320
suitable for light-load and high-speed rotations, and sure additives is suitable for use in places that are E ： VG32 M： VG460
500 500 100
high viscosity for heavy-load and low-speed rotations. subjected to heavy loads. F ： VG46 N ： VG680
300 300 G： VG68
Synthetic lubricants of the diester or silicon series are 50

Viscosity
C
200 200 40
used instead of lubricants of the petroleum series in 5  Miscibility of different greases 30
100 A B C D E F G H J K L M N
consideration of the pour point and high temperature In principle, it is desirable to use grease of the same 80
100 20
stability. brand. However, when the mixing of different greases 80
60
is unavoidable, greases with the same type of thick- 60 10
50
2  Thickener
As shown in Table 35, metal soap bases are mostly
ener and with a similar type of base oil should be
used. 40
50
D
5
used as thickeners. In particular, Na-soap is water- It should be noted that if different types of grease are 40 4
soluble and emulsifies easily, and it cannot be used in mixed, they may interact with each other and the con- -20 0 20 40 60 80 100 120 140 160 °C
damp or wet areas. The type of thickener and the sistency will become softer than that for the individual
pour point of grease have a close relationship. In greases. -20 0 20 40 60 80 100 120

Temperature
160 200 240 280 320 °F
E
general, the higher the pour point, the higher the max-
imum usable temperature of grease. However, even Lubricating oil
Fig. 25 Relationship between viscosity and temperature of lubricating oil
when the grease uses a thickener having a high pour
point, its upper operating temperature limit is low if its
base oil has low heat resistance.
For rolling bearings, refined mineral oil or synthetic oil
is used. To improve its properties, antioxidant addi- Table 38 Conditions of bearing use and examples of lubricating oil selection
F
tives, extreme pressure additives and detergent addi-
ISO viscosity grade(VG)
3  Consistency tives are added as required. Conditions

G
This represents the hardness grade of grease. When selecting lubricating oil, it is important to select 10 15 22 32 46 68 100 150 220 320 460 680
Grease becomes harder in proportion to the amount oil which has adequate viscosity under operating tem- Refrigerator oil
− 30 〜    0℃

of thickener if the same thickener is used. peratures. If the viscosity is too low, the formation of 

Immediately after grease has been stirred (usually 60 the oil film will be insufficient, causing abnormal wear

Operating temperature
Bearing oil
times), a depression is formed in the grease in a and seizure. On the other hand, if the viscosity is too

　  0 〜  50℃ 
specified time using a specified cone. The consisten-
cy (combined consistency) is expressed by the value
high, it will generate excessive heat or increase power
loss due to viscous resistance. As a general stan-
 Turbine oil
 H
 Bearing oil
of depth of depression (mm) multiplied by 10. dard, oil having higher viscosity should be used for 　50 〜  80℃ 
Turbine oil
This value gives an estimate of the fluidity during heavier loads and oil having lower viscosity should be 

operation with a greater value for softer grease.
Table 36 shows the consistency number of grease
used for higher rotational speeds.
Under conditions of normal use for various bearings, 　80 〜 110℃

Turbine oil
Bearing oil

Gear oil
I
and the relationship between the consistency and the values of viscosity shown in Table 37 will be a
 
 
operating conditions. guideline.
d mn value

Large  Small
The relationship between viscosity and temperature Load
J

Small  Large
Table 36 Consistency and operating conditions of grease can be obtained from Fig. 25. Also, Table 38 shows
examples of selecting lubricating oil according to the Remarks　・Lubricating oils are based on JIS K 2211 (Refrigerating machine oils), JIS K 2239 (Bearing Oil), JIS K 2213 (Turbine Oil), and
NLGI JIS K 2219 (Gear Oil).
Combined consistency Application conditions of bearing use.
consistency number 　　　　　・The method of lubrication in these cases is mainly oil bath lubrication or circulating lubrication.
　　　　　・When the temperature is on the high side within the operating temperature range, oils of high viscosity are used.
385 〜 355
K
0 For centralized lubrication, 　　　　　・d mn represents the mean value of the bore and outside diameters (mm) of the bearing multiplied by the rotational speed (min-1).
Table 37 Bearing series and required viscosity of lubricating oil
1 340 〜 310 For oscillating motion
Kinematic viscosity at
2 295 〜 265 For general use Bearing series
operating temperatures
3 250 〜 220 For general use, For high temperature
Needle roller bearings
4 205 〜 175 For sealing with grease
Roller bearings
13 mm2/s or more
L
4  Additives Crossed roller bearings 20 mm2/s or more
Additives include various types of substances, which

M
Thrust needle roller bearings
are added to grease in small quantities to improve its 32 mm2/s or more
Thrust roller bearings
characteristics. For example, when a bearing is kept

1N=0.102kgf=0.2248lbs.
A53 1mm=0.03937inch
A54
C-Lube Bearing ・To ensure normal rotation of the bearing, apply a
load of 1% or more of the basic dynamic load rating
Friction and Allowable Allowable rotational speed A
C-Lube Bearing is a bearing that is lubricated at use. Rotational Speed As the rotational speed of rolling bear ings is
with a newly developed thermosetting solid-type lubri- ・The allowable rotational speed is different from that increased, the bearing temperature also increases
Friction
B
cant. A large amount of lubricating oil and fine parti- of the general needle roller bearings. For dmn, d1n, due to the heat generated at the contact surfaces
cles of ultra high molecular weight polyolefin resin are and dn, use the values in Table 39 or less as guide- between the cage, raceways and rolling elements,
solidified by heat treatment to fill the inner space of lines. Compared with sliding bearings, the starting (static) until it finally leads to bearing seizure. It is therefore
the bearing. As the bearing rotates, the lubricating oil friction for rolling bearings is small, and the difference necessary to maintain the rotational speed of a bear-
oozes out onto the raceway in proper quantities, between the starting (static) friction and the kinetic ing below a certain limit value to ensure safe opera-
maintaining the lubrication performance for a long
period of time. Solid-type lubricant
friction is also small. The loss of power and tempera-
ture rise in machines are thus reduced, improving the
tion for long periods. This limit value is called the
allowable rotational speed.
C
The dimension tables for C-Lube Machined Type mechanical efficiency. Since the amount of heat generated is approximately
Needle Roller Bearings, C-Lube Cam Followers, and Frictional torque is influenced by the bearing type, proportional to the sliding speed at the contact area,
C-Lube Roller Followers are shown on pages D77,
I49, and I95.
bearing load, rotational speed, lubricant characteris-
tics, etc. It varies according to the lubricant when
this sliding speed is an approximate guide indicating
the limit of the bearing rotational speed. D
C-Lube Bearing is available in all Needle Roller operated under light-loads and high-speed conditions, The allowable rotational speed of bearings thus varies
Bearing series. Also C-Lube Bearings for food pro- and according to the load when operated under according to the bearing type, size, bearing load,
cessing are available, using NSF H1-certified lubrica- heavy-loads and low-speed conditions. method of lubrication, radial clearance, and other
E
Needle roller

tion oil and resin compliant with FDA standards to mit- Frictional torque of rolling bearings is complicated such factors.
igate any effect on human health. If needed, please because it is influenced by various factors, but for The allowable rotational speeds shown in the table of
contact . convenience, it can be expressed approximately by dimensions are empirical values. They are not
Outer ring
the following equations. absolute values and can be changed according to the
Features of C-Lube Bearing
Structure of C-Lube Bearing
d
・Radial bearings　M ＝μ P　　……………………(37)
bearing use conditions. Depending on the structure
and accuracy around the bearing, the lubricant and
F
・Most suitable for preventing grease dry-up in appli- 2 the lubrication method, it is possible for some bear-
dm ings to be operated at more than twice the allowable
cations where lubrication is difficult. ・Thrust bearings　M ＝μ P　　……………………(38)
2
・Great reduction of maintenance work by extending
G
rotational speed given in the table without trouble.
Table 39 C-Lube Bearing dmn , d1n , dn
the lubrication interval. 　　where,　M ：Frictional torque, N-mm
Representative model Allowable rotational speed
・Elimination of oil contamination, making this bear- 　　　　　　μ ：Coefficient of friction
Main model code dmn（1）、d1n（2）、dn（3）
ing most suitable for applications that would be
C-Lube Machined Type Needle Roller Bearings TAF･･･/SG dmn=20 000 　　　　　　P ：Bearing load, N
adversely affected by oil.

Cautions for using C-Lube Bearing

C-Lube Cam Followers
C-Lube Roller Followers（4）
CF･･･/SG
NART･･･/SG
d1n =10 000
dn = 8 000
　　　　　　d ：Bearing bore diameter, mm
　　　　　　d m：Mean value of bearing bore and H
Notes(1)   
dmn ＝＝（bore diameter of bearing［mm］＋ outside diameter of bearing［mm］） outside diameters, mm
　　　　　　　　 /2 × rotational speed［min-1］
・Never wash C-Lube Bearing with organic solvent (2)   d1n ＝ ＝ stud diameter［mm］×rotational speed［min-1］
and/or white kerosene which have the ability to
remove fat, or leave the bearing in contact with
(3)   dn ＝ ＝ inner ring bore diameter［mm］×rotational speed［min-1］
(4)   The allowable rotational speed of C-Lube Roller Followers
The approximate coefficients of friction of
Bearings under operating conditions, in which lubrica- I
is applicable to use with oscillating rotation. For use with tion and mounting are correct and where loads are
these agents. one-way or continuous rotation, please consult .
・The operating temperature range is -15 〜 +80°C. relatively large and stable, are shown in Table 40.

J
For continuous operation, the recommended oper-
ating temperature is +60°C or less. Table 40 Coefficient of friction

Bearing series μ

0.0010 〜 0.0030
K
Needle roller bearings with cage
Full complement needle roller bearings 0.0030 〜 0.0050
Thrust needle roller bearings 0.0030 〜 0.0040
Thrust roller bearings 0.0030 〜 0.0040

1N=0.102kgf=0.2248lbs.
A55 1mm=0.03937inch
A56
Operating Temperature Range Handling of Bearings Methods of mounting When press fitting, the friction of the fitting surfaces
can be reduced by applying high viscosity oil over the
A
Mounting methods of bearings are different according fitting surfaces.
The allowable operating temperature range for needle Precautions in handling to the type of bearing and the fit. In general, mount- The pressing-in or pulling-out force to be applied to
roller bearings is generally -20 〜 +120°C.

B
ing of needle roller bearings is comparatively easy. the bearing is given on page A59.
When operating at temperatures outside this range, Since the bearing is a high-accuracy mechanical ele-
However, non-separable bearings with large interfer-
the operation may be limited by the allowable temper- ment, special attention must be paid to its handling.
ences should be handled with great care. 2  Mounting by shrink fitting
ature range of prepacked grease, seal, cage material, The following precautions should be noted when han-
This method is used when the interference is great or
etc. Further, if the bearing is used at high tempera- dling the bearings.
1  Mounting by press fit when a large bearing is to be fitted. The housing is
C
ture, i.e. 120°C or above, the amount of dimensional
Small and medium bearings with small interferences heated and thermally expanded when fitting the outer
displacement gets larger. So special heat treatment is 1  Bearings and their surrounding parts should be kept clean.
require a small pressing-in force for mounting, and ring to the housing and the inner ring is heated and
necessary. Bearings and their surrounding parts must be kept
they are mounted using a press at room temperature. expanded when fitting it to the shaft allowing the bear-
The operating temperature range for some types of clean paying special attention to dust and dirt. Tools
The bearing should be pressed in carefully, applying a ing to be set easily within a short time. The maximum
bearings is different from the above. See the section and the working environment should also be cleaned.
for each bearing.
2  Bearings should be handled carefully.
force evenly to the bearing with a fitting tool as shown
in Fig. 26. For separable bearings, the inner and
allowable temperature for the shrink fit is +120°C, and
heating should be performed appropriately. Pure D
outer rings can be mounted separately, and the non-corrosive mineral oil is recommended as the
A shock load during handling may cause scratches,
mounting work is simple. However, when installing heating oil for shrink fit, and insulation oil for trans-
indentations and even cracks or chips on the raceway
the shaft and inner ring assembly into the outer ring, formers is considered to be the best. During cooling,
surfaces and rolling elements.
care should be taken not to damage the raceway sur- the bearing also shrinks in the axial direction. E
faces and rolling elements. Therefore, to ensure that there is no clearance
3  Bearings should be mounted or dismounted with proper tools.
between the bearing and the shoulder, an axial force
When mounting and dismounting, tools suitable for
must be applied continuously to the bearing until it
the bearing type should be used.
has cooled.
When the interference between the outer ring and the
F
4  Bearings should be protected against corrosion.
housing is great, an expansion fit method in which the
Bearings are treated with anti-corrosive oil. However,
bearing is cooled using dry ice or other cooling agent
when handling them with bare hands, sweat from the

G
before fitting can be used. Immediately after fitting,
hands may result in future rust formation. Gloves
however, moisture from the air easily condenses on
should be worn, or hands should be dipped in mineral
the bearing. Therefore, it is necessary to take pre-
oil.
ventive measures against corrosion.

Mounting
Fig. 26
H
Preparation When mounting non-separable bearings, the inner
and outer rings are pressed in simultaneously by
Before mounting the bearing, the dimensions and fil-
lets of the shaft and housing should be checked to
applying a cover plate as shown in Fig. 27. It must
never happen that the inner ring is press-fitted to the I
ensure that they conform to specifications. shaft by striking the outer ring, or the outer ring by
Bearings should be unwrapped just before mounting. striking the inner ring, because the raceway surfaces

J
In case of grease lubrication, bearings should be filled and rolling elements will be scratched or indented.
with grease without cleaning the bearings. Even in
the case of oil lubrication, it is normally unnecessary
to clean the bearings. However, when high accuracy
is required or when using at high speeds, the bear-
ings should be cleaned using cleaning oil to remove
thoroughly oily contents. The cleaned bearings
K
should not be left alone without anti-corrosive precau-
tions, because bearings can easily be corroded after
anti-corrosive agents are removed.
Lubricating grease is prepacked in some types of
L
bearings. Therefore, refer to the relevant section for
Fig. 27
each bearing.

1N=0.102kgf=0.2248lbs.
A57 1mm=0.03937inch
A58
Pressing force and pulling force Dismounting Dismounting of inner ring
A
Guidelines for the pressing force when pressing in the Dismounting of the bearings is carried out for the peri- In the case of bearings such as needle roller bearings
inner ring to the shaft and the pulling force when odic inspection or repairs of machines. By inspecting in which the inner and outer rings are separable, the

B
pulling it out are obtained from the following equation. the bearing, related parts or mechanisms, lubrication, simplest way to press out the inner ring is by using a
etc., important data is obtained. In the same manner press as shown in Fig. 29.
　　　K ＝ f k　　　   ∆ d f｛
d＋2
d d 2
B  1 −　　 ｝
F
   ………(39) ( ) as in mounting, care should be taken to prevent dam-
age to the bearing or other parts.
The puller shown in Fig. 30 is also generally used.
This is designed according to the bearing size. In
　　where, 　K ：Pressing or pulling force, N A suitable dismounting method should be selected addition, there are a 3-hook puller (Fig. 31) and a 2-
　　　　　　 f k ：Resistance factor determined by the coefficient of friction according to the type of the bearing, fit, etc. Bearings
mounted by interference fit are especially difficult to
hook puller for wide-range use. C
　　　　　　 When pressing in inner ring to shaft,  f k=4×104
dismount, and it is necessary to give due considera- Fig. 31
　　　　　　 When pulling out inner ring from shaft,  f k=6×104
tion to the structure around the bearing during the
　　　　　　d 　：Bore diameter of inner ring, mm Press

　　　　　　∆ d f ：Apparent interference, mm

design stage.
In addition to these, when it is difficult to remove the D
　　　　　　B 　：Width of inner ring, mm Dismounting of outer ring
inner ring due to high shoulders, several holes for
　　　　　　F 　：Outside diameter of inner ring, mm removal pins are made through the shoulder, or sev-
The actual pressing force or pulling force may be eral hook grooves are cut in the shoulder as shown in
Outer rings mounted by interference fit are dismount-
greater than the calculated value due to mounting
errors. When designing a puller, it is necessary that
ed as shown in Fig. 28, by screwing in the push-out
Fig. 32 and Fig. 33.
When a bearing is not to be used again after removal, E
bolts evenly through several screw holes provided at
the puller has the strength (rigidity) to withstand more it may be removed by heating with a torch lamp.
places corresponding to the side face of the outer
than 5 times the calculated value. ring.

F
Running test
After mounting the bearing, a running test is carried
out to check whether the mounting is nor mal. G
Usually, it is first checked by manual turning. Then, it
is operated by power gradually from no-load and low-
speed up to normal operating conditions to check for
abnormalities.
Noise can be checked by using a soundscope or simi- Fig. 29
H
Fig. 32
lar instrument. In this test, checks are carried out for
the following abnormalities.
Fig. 28

1  Manual turning I
　(a) Uneven torque ……………… Improper mounting
　(b) Sticking and rattling … Scratches or indentations
on the raceway surface
　(c) Irregular noise … Penetration of dust or foreign
particles
J
2  Power running
　(a) Abnormal noise or vibration … Indentations on
the raceway surface, too great clearance Fig. 30 Fig. 33 K
　(b) Abnormal temperature … Unsuitable lubricant,
improper mounting, too small clearance

1N=0.102kgf=0.2248lbs.
A59 1mm=0.03937inch
A60
Inspection of bearing Maintenance and inspection Table 41 Damage, causes and corrective action
A
Cleaning of bearing Maintenance and inspection Condition of bearing damage Cause Corrective action

Flakings at opposite circumferential positions on raceway

B
When inspecting a bearing after removal, the appear- Maintenance and inspection are carried out to main- Improper roundness of housing bore Correction of housing bore accuracy
surfaces
ance of the bearing should be recorded first. Then, tain good performance of bearings installed in the
after the residual amount of lubricant is checked and machine. Flakings in the vicinity of raceway surface edges and roller Improper mounting, Shaft deflection, Poor Careful mounting, Careful centering, Correction
ends centering, Poor accuracy of shaft or housing of shoulders of shaft and housing for right angles

Flaking
a sample of lubricant is collected, the bearing should Maintenance is performed by checking the machine
be cleaned. operating conditions, checking and replenishing or Flakings on raceway surfaces with an interval corresponding to Great shock load when mounting, Rusting Careful mounting, Protection against rust for
For cleaning, light oil or kerosene is commonly used.
Cleaning is divided into rough cleaning and final
replacing the lubricant, checking the bearing and
related parts by periodic disassembly and other such
roller pitch during machine stoppage
Too small clearance, Too great load, Poor
long periods of machine stoppage
Correct selection of fit and clearance
C
Early flaking on raceway surfaces and rolling elements
cleaning, and wire gauze is set as a raised bottom in procedures. lubrication, Rusting, etc. Correct selection of lubricant
a container to prevent the bearing from touching the Items for inspection of a running bearing in a machine Poor lubrication in early stage
Selection of softer grease,
bottom of the container. include the bearing temperature, noise, vibration and Galling on raceway surfaces and rolling surfaces of rollers Grease consistency too hard
Avoiding quick acceleration D

Galling
Lubricating grease and adhering substances such as condition of lubricant. High acceleration at start
foreign particles are removed with a brush, etc., When any abnormality is found during operation, the Poor lubrication, Poor mounting, Correct selection of lubricant
Galling between roller end faces and collar guide surfaces
using oil for rough cleaning. Care should be taken cause should be investigated and measures taken by Large axial load Correct mounting
during this process, because if the bearing is turned referring to the section on running test on page A59.
E
Excessive shock load, Too much interference. Reevaluation of load conditions, Correction of fit,
with foreign particles attached, the raceway surfaces When removing a bearing, refer to the section on dis- Poor cylindricity of shaft. Too large fillet radius, Correction of machining accuracy of shaft or
Cracks in outer or inner ring
may be scratched. mounting on page A59. Development of thermal cracks, sleeve, Making fillet radius smaller than the
Final cleaning is carried out by turning the bearing in Development of flaking chamfer dimension of bearing

Breakage
cleaning oil. It is desirable that the cleaning oil is kept Damage, causes and corrective action Development of flaking

F
Cracked rolling elements,
clean by filtering. Immediately after cleaning, the Shock to collar when mounting, Careful handling and mounting
broken collar
bearing must be protected against corrosion. Rolling bearings can generally be used fully up to Dropped by careless handling
their rolling fatigue life if they are properly selected, Abnormal load to cage by poor mounting, Minimizing mounting errors,
Broken cage
Inspection and evaluation of bearing mounted, operated and maintained. However, they Poor lubrication Study of lubricating method and lubricant

G
may actually be damaged earlier than their expected Indentations on raceway surfaces at an interval Shock load applied when mounting,
The judgement as to whether the removed bearing is lifetimes creating problems or accidents. Common Careful handling
corresponding to the pitch between rolling elements (brinelling) Excessive load while stopping

Dent
reusable depends on the inspection after cleaning. causes of damage include improper mounting or han-
Biting of foreign substances such as Cleaning of housing, Improvement of sealing,
Conditions of the raceway surfaces, rolling elements dling, insufficient lubrication and penetration of foreign Indentation on raceway surfaces and rolling surfaces of rollers
metal chips and sands Use of clean lubricant
and fitting surfaces, wear condition of the cage, particles.
increase of bearing clearance, dimensions, rotational
accuracy, etc. should be checked for damage and
It may be difficult to determine the exact cause of a
problem by checking only the damaged bearing. The
False brinelling
(Phenomenon like brinelling)
Vibration when the bearing is stationary such
as during transportation,
Fixing of shaft and housing,
Use of lubricating oil, H
Oscillating motion with small amplitude Application of preload to reduce vibration
abnormalities. conditions of the machine before and after the occur-
Fretting

Abnormal wear
The evaluation is performed based on the experience rence of the damage, the location and the operating Increase of interference,
Localized wear of fitted surfaces accompanied by red-brown Sliding between fitted surfaces
taking into consideration the degree of damage,
machine performance, importance of the machine,
and ambient conditions of the bearing, the structure
around the bearing, etc. should also be examined. It
wear particles
Wear on raceway surfaces, collar surfaces, rolling surfaces of Penetration of foreign particles, Poor
Application of oil

Improvement of sealing, Cleaning of housing

I
operating conditions, period until the next inspection, then becomes possible to assess the cause of the
rollers, cages, etc. lubrication, Rust Use of clean lubricant
and other such factors. damage by linking the conditions of the damaged
bearing to the probable causes arising from the Creep Sliding between fitted surfaces, Increase of interference,

machine operation, and to prevent the recurrence of

Wear on fitted surfaces Insufficient tightening of sleeve Correct tightening of sleeve
Supply of proper amount of proper lubricant,
J
similar problems. Discoloration of rolling elements and/or raceway surfaces

Seizure
Common types of damage, causes and corrective Poor lubrication, Too small clearance, Poor Rechecking of fit and bearing clearance
and/or flange surfaces, Adhesion and welding, Discoloration of
mounting Rechecking of mounting dimensions and related
action are listed in Table 41. cage

K
parts

corrosion corrosion
Insulation of bearing,
Electric
Ripples on raceway surfaces Melting by sparks due to electric current
Grounding to avoid electric current
Careful storage if under high temperature and
Rust or corrosion on bearing inside surfaces or Condensation of vapor in air,
Rust,

high humidity, Protection against rust,

on fitted surfaces Penetration of corrosive substances
Improvement of sealing L

1N=0.102kgf=0.2248lbs.
A61 1mm=0.03937inch
A62
 Shell Type
Shell
Needle
TypeRoller
NeedleBearings
Roller Bearings
TA・TLA・BA
TA・TLA
BHA・BA・BHA B1 B1

Needle Roller
NeedleCages
Roller
forCages
general
forusage
generalKT
usage KT C1 C1

Needle Roller
NeedleCages
Roller
forCages
enginefor
connecting
engine connecting
rods KT…EG
rods ・KT…EG・KTV…EG
KTV…EG C17 C17

MachinedMachined
Type Needle
TypeRoller
NeedleBearings
Roller Bearings
NA・TAFI・
NA・・
TRI BRI・TRI・BRI
TAFI D1 D1

C-Lube Machined
C-Lube Machined
Type Needle
TypeRoller
NeedleBearings
Roller Bearings
TAF…/SGTAF…/SG D75 D75

Needle Roller
NeedleBearings
Roller Bearings
with separable
with separable
cage NAF cage NAF D79 D79

Roller Bearings
Roller Bearings
NAG・NAU・TRU
NAG・NAU
・NAS
・TRU・NAS E1 E1

Thrust Bearings
Thrust Bearings
NTB・AS・NTB
AZK・
・AS
WS・・GS・WS・GS
AZK F1 F1

Combined
Combined
Type Needle
TypeRoller
NeedleBearings
Roller Bearings
NAX・NBX・NATA
NAX・NBX
・NATB
・NATA・NATB G1 G1

Inner Rings
InnerIRT
Rings
・IRB・IRT
LRT・・
IRB・LRT・LRB
LRB H1 H1

Cam Followers
Cam Followers
CF・CFKRCF
・CFS
・CFKR
・NUCF
・CFS
・CR
・NUCF・CR I1 I1

C-Lube Cam
C-Lube
Followers
Cam Followers
CF…/SG CF…/SG I49 I49

Roller Followers
Roller Followers
NAST・NART・NURT
NAST・NART
・CRY
・NURT・CRY I77 I77

C-Lube Roller
C-LubeFollowers
Roller Followers
NART…/SG
NART…/SG I95 I95

Crossed Crossed
Roller Bearings
Roller Bearings
CRBH(V)・CRBH
CRBC・ )・CRBC
(VCRB ・CRBT
・CRB
・CRBS
・CRBT
・CRBF
・CRBS
(V)・CRBF
J1 (V) J1

SphericalSpherical
BushingsBushings
SB・GE・SBB
SB・GE・SBB K1 K1

PilloballsPilloballs
PB・PHS・PB・PHS
POS・PHSA
・POS・PHSA K29 K29

L-balls L-balls
LHSA・LHSLHSA・LHS K45 K45

Super Flexible
Super Nozzles
Flexible Nozzles
SNA・SNM・SNPT
SNA・SNM・SNPT K55 K55

Parts ForParts
Needle
ForRoller
NeedleBearings
Roller Bearings
OS・DS・WR・
OS・AR
DS・
・WR・AR・
Needle Roller
Needle Roller L1 L1
A63
 ■ Structure and features Structures of Shell Type Needle Roller Bearings
Shell Type Needle Roller Bearings are light-
Standard Caged Type
weight bearings with large load ratings. They employ Outer ring
a shell type outer ring made from a thin special-steel
plate which is accurately drawn, carburized and Thrust ring

●Shell Type Caged Needle Roller Bearings quenched, thus providing the lowest sectional height
among the needle roller bearings.
●Shell Type Grease Retained Full Complement Needle Roller Bearings There are two types of bearings available in this Needle Roller
series; the caged type and the full complement type.
The appropriate type can be selected according to the
Cage
operating conditions. The caged type has a structure
in which the needle rollers are accurately guided by
the cage and thrust rings. It is useful for applications
at high-speed rotation. The full complement type nee- Caged and closed end type Outer ring
dle roller bearing, on the other hand, is suitable for
heavy-load applications at low-speed rotation.
Since these bearings are press-fitted into the housing, Thrust ring
no fixtures for axial positioning are needed. They are
ideal for use in mass-produced articles that require
economy, and have a wide variety of applications. Needle Roller

Cage

Caged type with two seals Outer ring

Thrust ring

Needle Roller

Cage

Seal

Grease retained full complement type Outer ring

Needle Roller

B1 B2
■ Types ■ Identification Number Table 2.1 M
 easuring gauges for metric series
bearings unit: mm
Table 2.2 M
 easuring gauges for inch series
bearings unit: mm

Numerous varieties of Shell Type Needle Roller The identification number of Shell Type Needle Roller Fw Ring gauge Plug gauge Fw Ring gauge Plug gauge
Bearings are available as shown in Table 1. Nominal roller set Nominal roller set
Bearings consists of a model code and dimensions. TA…Z(1) TLA…Z(2) Go No-go bore diameter BA…Z( ) BHA…Z( ) Go No-go
1 2
bore diameter
Examples of the arrangement are shown below.
When using with inner rings, the assembled inner   4 −   7.981   4.004   4.016   3.969   7.155 −   3.990   4.016
Table 1 Type of bearing
rings shown in the dimension tables are used. An   5 −   8.981   5.004   5.016   4.762   8.730 −   4.783   4.808
Type Caged Full complement
example in this case is also shown below. Inner rings   6 −   9.981   6.004   6.016   6.350 11.125 −   6.388   6.414
Standard Closed end With seals（1）Grease retained
Series
are delivered separately.   7 − 10.977   7.005   7.020   7.938 12.713 14.300   7.976   8.001
− TLA … Z TLAM TLA … UU YTL   8 14.992 11.977   8.005   8.020   9.525 14.300 15.888   9.563   9.588
Metric series
Heavy duty TA … Z TAM − YT Examples of identification number   9 15.992 12.977   9.005   9.020 11.112 15.888 17.475 11.151 11.176
− BA … Z BAM − YB 10 16.992 13.977 10.005 10.020 12.700 17.475 19.063 12.738 12.764
Inch series Example 1
Heavy duty BHA … Z BHAM − YBH 15.977(3) 14.288 19.063 20.650 14.326 14.351
Model code Dimensions 12 18.991 12.006 12.024
Note(1)　When the heavy duty type with seals or the closed end 17.977(3) 15.875 20.650 22.238 15.913 15.938
type with one seal is required, please consult  . TA 18 20 Z 13 − 18.972 13.006 13.024 17.462 22.238 23.825 17.501 17.526
Remark　A "W" is added to the model code to indicate that the
rolling elements are of the double-row type. 14 21.991 19.972 14.006 14.024 19.050 25.387 26.975 19.063 19.088
Type of bearing
　　　　  Example　TAW 5045 Z 15 21.991 20.972 15.006 15.024 20.638 26.975 28.562 20.650 20.676
Roller set bore diameter 16 23.991 21.972 16.006 16.024 22.225 28.562 30.150 22.238 22.263
Shell Type Caged Needle Roller Bearings （18mm） 17 23.991 22.972 17.006 17.024 23.812 30.150 − 23.825 23.851
18 24.991 23.972 18.006 18.024 25.400 31.737 33.325 25.413 25.438
Outer ring width
Standard type （20mm） 19 26.991 − 19.007 19.028 26.988 33.325 − 27.000 27.026
This type has a narrow gap between the bore of the 26.991(4) 28.575 34.912 38.087 28.588 28.613
marked-side flange of the outer ring (brand, bearing 20 25.972 20.007 20.028
Example 2 (With inner ring) 27.991(4) 30.162 38.087 − 30.175 30.201
number, etc. are marked) and the shaft, which pre- 21 28.991 − 21.007 21.028 31.750 38.087 41.262 31.763 31.788
vents grease leaks and the entry of foreign particles. Identification number of Identification number of
Inner Ring 28.991(5) 33.338 41.262 − 33.350 33.378
Shell Type Needle Roller Bearing 22 27.972 22.007 22.028
This type has wide applications.
29.991(5) 34.925 41.262 44.437 34.938 34.966
TA 1820 Z ＋
  IRT 1520 30.989(6) 38.100 47.612 − 38.113 38.143
Closed end type 24 − 24.007 24.028
31.989(6) 41.275 50.787 − 41.288 41.318
This type is completely closed on one side of the
25 32.989 31.967 25.007 25.028 44.450 53.962 57.137 44.463 44.496
outer ring, and is ideal for use when perfect closing of
− −
■ Accuracy
26 33.989 26.007 26.028 47.625 57.137 47.638 47.671
shaft ends is desired.
28 36.989 34.967 28.007 28.028 50.800 60.312 − 50.815 50.848
The shape of the closed end surface of the outer ring
The outer rings of Shell Type Needle Roller Bearings 29 37.989 − 29.007 29.028 52.388 − 64.280 52.413 52.451
is divided into two types, and the dimensions t1 and t2
are thin and therefore cannot avoid deformation due 30 39.989 36.967 30.007 30.028 53.975 63.487 − 53.990 54.028
in the illustrations shown in the dimension tables
to heat treatment. It is thus not appropriate to take 32 41.989 − 32.009 32.034 57.150 66.662 − 57.165 57.203
apply to the bearings with the roller set bore diame-
35 44.989 41.967 35.009 35.034 66.675 76.187 − 66.700 66.738
ters, Fw > 22 and Fw ≦ 22, respectively. direct measurements of the bearing. The roller set
bore diameter is measured using a plug gauge or 37 46.989 − 37.009 37.034 69.850 79.362 − 69.875 69.914
Type with seals at both sides tapered gauge after press-fitting the bearing to a suit- 38 47.989 − 38.009 38.034 Notes(1)　Also applicable to BAM and YB
(2)　Also applicable to BHAM and YBH
This type has a wider outer ring than the standard able ring gauge. The gauge specifications are shown 40 49.989 46.967 40.009 40.034
type and is installed with seals consisting of a rein- in Tables 2.1 and 2.2. 45 54.988 51.961 45.009 45.034
Tolerances of outer ring width C are shown in Table 50 61.988 57.961 50.009 50.034 Table 3 Tolerances of outer ring width C unit: mm
forcing ring and special synthetic rubber to prevent
grease leaks and the entry of foreign particles. 3. 55 66.988 62.961 55.010 55.040
Series Tolerance
60 71.988 − 60.010 60.040
Shell Type Grease Retained Full Complement 62 73.988 − 62.010 62.040
Metric 0 〜− 0.20
Needle Roller Bearings 65 76.988 − 65.010 65.040
70 81.987 − 70.010 70.040
Inch 0 〜− 0.25
This type has full complement rollers which extend to Notes(1)　Also applicable to TAM and YT
(2)　Also applicable to TLAM, YTL, TLA…UU
the full width of the outer ring raceway. It can, there-
(3)　The upper value is for TLA 1210Z model, and the lower
fore, withstand heavy bearing loads and is most suit- value is for TLA 1212Z model.
able for low and medium rotational speeds as well as (4)　The lower value is for TA 202820Z model, and the upper
value is for models other than TA 202820Z model.
rocking motions. As lubricating grease is prepacked (5)　T he lower value is for TA 223016Z and TA 223020Z
with the rollers, the bearing can be operated immedi- models, and the upper value is for models other than
ately after being fitted. those models.
(6)　T he lower value is for TA 243216Z and TA 243220Z
models, and the upper value is for models other than
those models.

1N=0.102kgf=0.2248lbs.
B3 1mm=0.03937inch
B4
■ Fit Table 4 shows the recommended fit for Shell Type
Needle Roller Bearings. ■ Lubrication ■ Oil Hole
As the outer ring is thin, the correct dimensions and Table 5 shows a calculation example of radial clear- Bearings with prepacked grease are shown in Table For Shell Type Needle Roller Bearings with an oil
accuracy of Shell Type Needle Roller Bearings are ance after fitting. This calculation applies to bearings 6. ALVANIA GREASE S2 (SHOWA SHELL SEKIYU hole, "OH" is appended to the end of the identification
obtained only after they have been press-fitted into without inner ring to be fitted into rigid steel or cast K.K.) is prepacked as the lubricating grease. number.
the housing bore. Bearing accuracy is directly affect- iron housings. When the housing is made of light In the case of bearings without prepacked grease, 　Example　TA  2525  Z  OH
ed by housing dimensions, shape and rigidity. This alloy or a thin steel pipe, it is necessary to check perform proper lubrication for use. If the bearings are The symbol "OH" is not marked on the bearing itself,
should be taken into account when considering fit and dimensions by actual measurement. operated without lubrication, the wear of the roller but is shown on its packaging, etc. When bearings
accuracy. The radial clearance after fitting the bear- Generally, when making the radial clearance smaller, contact surfaces will increase and the bearing life will with multiple oil holes are required, please consult
ing to the shaft and the housing bore varies with their it is recommended that the shaft diameter be be shortened. .
tolerances. increased, without decreasing the housing bore diam-
eter. Table 6 Bearings with prepacked grease 〇：With prepacked grease　×：Without prepacked grease
Bearing type Caged Full complement

Table 4 Recommended fit Series Standard Closed end With seals Grease retained

Tolerance class TLA，TLAM，YTL × × 〇 〇

Metric series
Type of bearing Housing material Shaft (1) TA，TAM，YT × × − 〇
Housing bore × × 〇
Without inner ring With inner ring BA，BAM，YB −
Inch series
Steel BHA，BHAM，YBH × × − 〇
TA … Z，BA … Z，BHA … Z， h6 k5(j5) J7
Cast iron
TAM，BAM，BHAM，
■ Static Safety Factor
Light alloy
YT，YB，YBH h6 k5(j5) M7(N7)
(Thin steel pipe)
Steel Since Shell Type Needle Roller Bearings employ an
h6 k5(j5) N7
TLA … Z，TLAM，YTL， Cast iron outer ring made from a thin steel plate which is drawn, 15°
TLA … UU Light alloy carburized and quenched, excessively large loads
h6 k5(j5) R7(S7)
(Thin steel pipe) must be avoided. The required static safety factor is
Note(1)　When housings are made of light alloy or a thin steel pipe, the roller set bore diameter is greatly affected by the housing thickness and usually more than 3. D -0.2
-0.3
shape. Therefore, before mass-production assembly, assembly tests should be carried out to confirm the amount of dimensional
change and to determine the tolerance of the shaft which will give normal clearances.

Table 5 Calculation example of radial clearance after fitting unit: mm ■ Specifications of shaft and housing Fw-0.025
Calculation procedure Example of TLA 2020 Z Shell Type Needle Roller Bearings are commonly
used without an inner ring. In such cases, the surface
 1 Dimension of roller set bore diameter of bearing after it has been press-fitted into the ring gauge. From Table 2.1 on page B4 hardness of the raceway surface should be 58 〜
Dimension of ring gauge (D0): See Tables 2.1 and 2.2 on page B4. D0 ＝25.972 64HRC and the surface roughness should not exceed
Max. value of roller set bore dia. (Fw max): No-go dimension of plug gauge Fw max ＝20.028
0.2 μ mRa. However, when the operating condition is Fig.1 Example of mounting tool
Min. value of roller set bore dia. (Fw min): Go dimension of plug gauge Fw min ＝20.007
Gr

not severe, a surface roughness 0.8μmRa or less

 2 Dimension of housing bore From the dimension table on page B14, can be used.
Max. value of housing bore (Dmax): See the dimension table. Dmax＝25.993
If the surface hardness is low, the load rating must be
Min. value of housing bore (Dmin): See the dimension table. Dmin ＝25.972
Fw

D
F

corrected by the hardness factor shown on page A20.

 3 Dimension of roller set bore diameter of bearing after it has been press-fitted into the housing bore From the equations, When the shaft cannot be heat treated and finished
Max. value of roller set bore dia.(Fwe max)＝(Dmax−D0) ＋Fw max Fwe max＝20.049 by grinding, the use of Inner Rings for Shell
Min. value of roller set bore dia.(Fwe min)＝(Dmin−D0) ＋Fw min Fwe min ＝20.007
Type Needle Roller Bearings (See page H1.) is rec-
 4 Dimension of shaft From the dimension table on page B14, ommended.
Max. value of shaft dia. (Fmax): See the dimension table. Fmax ＝20.000
Min. value of shaft dia. (Fmin ): See the dimension table. Fmin ＝19.987
 5 Radial clearance after mounting From the equations, ■ Mounting
Max. value of radial clearance(Gr max)＝Fwe max−Fmin Gr max ＝0.062
D : Housing bore diameter Shell Type Needle Roller Bearings should be pressed
Min. value of radial clearance(Gr min) ＝Fwe min−Fmax Gr min ＝0.007
Fw : Roller set bore diameter The radial clearance into the housings gently using the appropriate tool as
F : Shaft diameter after mounting becomes
Gr : Radial clearance shown in Fig. 1, with their marked end surface up. As
0.007~0.062 mm. the outer ring is thin, it must never be struck directly
with a hammer. Fig.2 Mounting examples
Since the outer rings of Shell Type Needle Roller
Bearings are firmly fitted to housing bores with inter-
ference, it is unnecessary to fix them axially. Fig. 2
shows mounting examples.

1N=0.102kgf=0.2248lbs.
B5 1mm=0.03937inch
B6
 SHELL TYPE NEEDLE ROLLER BEARINGS

C C C

t2

Fw
Fw
Fw

D
D
D
TA … Z　TLA … Z TAM TLAM YT YTL

Shaft dia. 4 − 10 mm

Identification number Boundary dimensions Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft mm load rating load rating rotational inner ring
speed(1)
dia.
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
(Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) Fw D C t2 h6 J7 N7
mm g g g g g Max. Max. Min. Max. Min. Max. Min. N N min-1

4 ─ ─ ─ ─ TLA 48 Z 1.54 TLAM 48 1.67 ─ ─ 4 8 8 1 1 350 1 010 75 000 ─

4.000 3.992 ─ ─ 7.996 7.981
─ ─ ─ ─ ─ ─ ─ ─ YTL 48 1.73 4 8 8 ─ 3 010 2 900 40 000 ─

5 ─ ─ ─ ─ TLA 59 Z 1.9 TLAM 59 2 ─ ─ 5 9 9 1 1 880 1 600 65 000 ─

5.000 4.992 ─ ─ 8.996 8.981
─ ─ ─ ─ ─ ─ ─ ─ YTL 59 2.4 5 9 9 ─ 4 320 4 750 30 000 ─
6 ─ ─ ─ ─ TLA 69 Z 2.2 TLAM 69 2.3 ─ ─ 6 10 9 1 6.000 5.992 ─ ─ 9.996 9.981 2 100 1 900 55 000 ─
7 ─ ─ ─ ─ TLA 79 Z 2.5 TLAM 79 2.7 ─ ─ 7 11 9 1 7.000 6.991 ─ ─ 10.995 10.977 2 490 2 450 50 000 ─
─ ─ ─ ─ TLA 810 Z 3.1 TLAM 810 3.3 ─ ─ 8 12 10 1 8.000 7.991 ─ ─ 11.995 11.977 3 320 3 670 45 000 ─
TA 810 Z 6.7 TAM 810 7.1 ─ ─ ─ ─ ─ ─ 8 15 10 1.3 3 470 2 880 45 000 ─
8 TA 815 Z 9.7 TAM 815 10.1 ─ ─ ─ ─ ─ ─ 8 15 15 1.3 5 780 5 570 45 000 ─
8.000 7.991 15.010 14.992 ─ ─
TA 820 Z 12.9 TAM  820 13.3 ─ ─ ─ ─ ─ ─ 8 15 20 1.3 8 340 8 920 45 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YT 810 7.7 8 15 10 ─ 7 530 7 950 19 000 ─
─ ─ ─ ─ TLA 910 Z 3.4 TLAM 910 3.6 ─ ─ 9 13 10 1 3 500 4 040 45 000 ─
9.000 8.991 ─ ─ 12.995 12.977
─ ─ ─ ─ TLA  912 Z 4 TLAM 912 4.3 ─ ─ 9 13 12 1 4 460 5 510 45 000 ─
9 TA 912 Z 8.7 TAM 912 9.2 ─ ─ ─ ─ ─ ─ 9 16 12 1.3 5 140 4 880 45 000 ─
TA  916 Z 11.4 TAM  916 11.9 ─ ─ ─ ─ ─ ─ 9 16 16 1.3 9.000 8.991 16.010 15.992 ─ ─ 6 960 7 210 45 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YT 912 10.1 9 16 12 ─ 9 690 11 200 17 000 ─
─ ─ ─ ─ TLA 1010 Z 3.7 TLAM 1010 4 ─ ─ 10 14 10 1 3 870 4 740 40 000 IRT 710
─ ─ ─ ─ TLA 1012 Z 4.4 TLAM 1012 4.8 ─ ─ 10 14 12 1 10.000 9.991 ─ ─ 13.995 13.977 4 920 6 460 40 000 IRT 712
─ ─ ─ ─ TLA 1015 Z 5.5 TLAM 1015 5.9 ─ ─ 10 14 15 1 6 390 9 040 40 000 IRT 715
10 TA 1010 Z 7.9 TAM 1010 8.5 ─ ─ ─ ─ ─ ─ 10 17 10 1.3 4 150 3 780 40 000 IRT 710
TA 1012 Z 9.3 TAM 1012 10 ─ ─ ─ ─ ─ ─ 10 17 12 1.3 5 590 5 540 40 000 IRT 712
10.000 9.991 17.010 16.992 ─ ─
TA 1015 Z 11.5 TAM 1015 12.2 ─ ─ ─ ─ ─ ─ 10 17 15 1.3 6 920 7 300 40 000 IRT 715
TA 1020 Z 15.4 TAM 1020 16 ─ ─ ─ ─ ─ ─ 10 17 20 1.3 9 990 11 700 40 000 ─

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B7 1mm=0.03937inch
B8
 SHELL TYPE NEEDLE ROLLER BEARINGS

C C C

t2

Fw
Fw
Fw

D
D
D
TA … Z　TLA … Z TAM TLAM YT YTL

Shaft dia. 12 − 15 mm

Identification number Boundary dimensions Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft mm load rating load rating rotational inner ring
speed(1)
dia.
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
(Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) Fw D C t2 h6 J7 N7
mm g g g g g Max. Max. Min. Max. Min. Max. Min. N N min-1

─ ─ ─ ─ TLA 1210 Z 4.3 TLAM 1210 4.7 ─ ─ 12 16 10 1 4 350 5 810 35 000 IRT 810
12.000 11.989 ─ ─ 15.995 15.977
─ ─ ─ ─ ─ ─ ─ ─ YTL 1210 5.1 12 16 10 ─ 7 470 11 800 13 000 IRT 810
─ ─ ─ ─ TLA 1212 Z 8.6 TLAM 1212 9.4 ─ ─ 12 18 12 1.3 12.000 11.989 ─ ─ 17.995 17.977 6 420 7 490 35 000 IRT 812
12 TA 1212 Z 10.5 TAM 1212 11.5 ─ ─ ─ ─ ─ ─ 12 19 12 1.3 6 000 6 310 35 000 IRT 812
TA 1215 Z 13.1 TAM 1215 14 ─ ─ ─ ─ ─ ─ 12 19 15 1.3 7 440 8 320 35 000 IRT 815
TA 1220 Z 17.3 TAM 1220 18.3 ─ ─ ─ ─ ─ ─ 12 19 20 1.3 12.000 11.989 19.012 18.991 ─ ─ 10 700 13 300 35 000 ─
TA 1225 Z 21.5 TAM 1225 22.5 ─ ─ ─ ─ ─ ─ 12 19 25 1.3 13 800 18 300 35 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YT 1212 12.8 12 19 12 ─ 11 800 15 200 13 000 IRT 812
13 ─ ─ ─ ─ TLA 1312 Z 9.2 TLAM 1312 10.1 ─ ─ 13 19 12 1.3 13.000 12.989 ─ ─ 18.993 18.972 6 760 8 170 30 000 IRT 1012
─ ─ ─ ─ TLA 1412 Z 9.8 TLAM 1412 10.8 ─ ─ 14 20 12 1.3 7 080 8 840 30 000 IRT 1012-2
14.000 13.989 ─ ─ 19.993 19.972
─ ─ ─ ─ TLA 1416 Z 13.2 TLAM 1416 14.3 ─ ─ 14 20 16 1.3 8 950 12 000 30 000 IRT 1016-2
14
TA 1416 Z 18.4 TAM 1416 19.6 ─ ─ ─ ─ ─ ─ 14 22 16 1.3 10 500 12 000 30 000 IRT 1016-2
14.000 13.989 22.012 21.991 ─ ─
TA 1420 Z 23 TAM 1420 24 ─ ─ ─ ─ ─ ─ 14 22 20 1.3 13 900 17 200 30 000 IRT 1020-2
─ ─ ─ ─ TLA 1512 Z 10.4 TLAM 1512 11.5 ─ ─ 15 21 12 1.3 7 380 9 520 25 000 IRT 1212
─ ─ ─ ─ TLA 1516 Z 14 TLAM 1516 15.2 ─ ─ 15 21 16 1.3 15.000 14.989 ─ ─ 20.993 20.972 9 330 12 900 25 000 IRT 1216
─ ─ ─ ─ TLA 1522 Z 19.1 TLAM 1522 20.5 ─ ─ 15 21 22 1.3 13 600 20 900 25 000 IRT 1222

15 TA 1510 Z 10.8 TAM 1510 12.3 ─ ─ ─ ─ ─ ─ 15 22 10 1.3 5 290 5 680 25 000 IRT 1010-1
TA 1512 Z 12.9 TAM 1512 14.3 ─ ─ ─ ─ ─ ─ 15 22 12 1.3 7 120 8 310 25 000 IRT 1012-1
TA 1515 Z 15.9 TAM 1515 17.3 ─ ─ ─ ─ ─ ─ 15 22 15 1.3 15.000 14.989 22.012 21.991 ─ ─ 8 830 11 000 25 000 IRT 1015-1
TA 1520 Z 21 TAM 1520 22.5 ─ ─ ─ ─ ─ ─ 15 22 20 1.3 12 700 17 600 25 000 IRT 1020-1
TA 1525 Z 25 TAM 1525 26.5 ─ ─ ─ ─ ─ ─ 15 22 25 1.3 16 300 24 200 25 000 IRT 1025-1

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B9 1mm=0.03937inch
B10
 SHELL TYPE NEEDLE ROLLER BEARINGS

C C C

t2

Fw
Fw
Fw

D
D
D
TA … Z　TLA … Z TAM TLAM YT

Shaft dia. 16 − 19mm

Identification number Boundary dimensions Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft mm load rating load rating rotational inner ring
speed(1)
dia.
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
(Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) Fw D C t2 h6 J7 N7
mm g g g g g Max. Max. Min. Max. Min. Max. Min. N N min-1

─ ─ ─ ─ TLA 1612 Z 10.9 TLAM 1612 12.2 ─ ─ 16 22 12 1.3 7 670 10 200 25 000 IRT 1212-1
─ ─ ─ ─ TLA 1616 Z 14.8 TLAM 1616 16.1 ─ ─ 16 22 16 1.3 16.000 15.989 ─ ─ 21.993 21.972 9 700 13 800 25 000 IRT 1216-1
16 ─ ─ ─ ─ TLA 1622 Z 20 TLAM 1622 21.5 ─ ─ 16 22 22 1.3 14 200 22 400 25 000 IRT 1222-1
TA 1616 Z 20 TAM 1616 22 ─ ─ ─ ─ ─ ─ 16 24 16 1.3 11 100 13 300 25 000 IRT 1216-1
16.000 15.989 24.012 23.991 ─ ─
TA 1620 Z 25 TAM 1620 27 ─ ─ ─ ─ ─ ─ 16 24 20 1.3 14 700 19 100 25 000 IRT 1220-1
─ ─ ─ ─ TLA 1712 Z 11.5 TLAM 1712 13 ─ ─ 17 23 12 1.3 17.000 16.989 ─ ─ 22.993 22.972 7 960 10 900 25 000 ─
TA 1715 Z 17.6 TAM 1715 19.5 ─ ─ ─ ─ ─ ─ 17 24 15 1.3 9 660 12 700 25 000 IRT 1215-2
17 TA 1720 Z 23.5 TAM 1720 25 ─ ─ ─ ─ ─ ─ 17 24 20 1.3 13 900 20 400 25 000 IRT 1220-2
TA 1725 Z 29 TAM 1725 31 ─ ─ ─ ─ ─ ─ 17 24 25 1.3 17.000 16.989 24.012 23.991 ─ ─ 17 900 28 100 25 000 IRT 1225-2
─ ─ ─ ─ ─ ─ ─ ─ YT 1715 20.5 17 24 15 ─ 16 600 26 000 9 000 IRT 1215-2
─ ─ ─ ─ ─ ─ ─ ─ YT 1725 35.5 17 24 25 ─ 27 200 49 000 9 000 IRT 1225-2
─ ─ ─ ─ TLA 1812 Z 12 TLAM 1812 13.7 ─ ─ 18 24 12 1.3 8 230 11 500 20 000 IRT 1512
18.000 17.989 ─ ─ 23.993 23.972
─ ─ ─ ─ TLA 1816 Z 16.2 TLAM 1816 17.9 ─ ─ 18 24 16 1.3 10 400 15 600 20 000 IRT 1516
TA 1813 Z 16.4 TAM 1813 18.5 ─ ─ ─ ─ ─ ─ 18 25 13 1.3 9 100 12 000 20 000 IRT 1513
18 TA 1815 Z 18.5 TAM 1815 20.5 ─ ─ ─ ─ ─ ─ 18 25 15 1.3 10 100 13 600 20 000 IRT 1515
TA 1817 Z 21 TAM 1817 23 ─ ─ ─ ─ ─ ─ 18 25 17 1.3 11 900 16 900 20 000 IRT 1517
18.000 17.989 25.012 24.991 ─ ─
TA 1819 Z 23.5 TAM 1819 25.5 ─ ─ ─ ─ ─ ─ 18 25 19 1.3 13 700 20 200 20 000 IRT 1519
TA 1820 Z 24.5 TAM 1820 26.5 ─ ─ ─ ─ ─ ─ 18 25 20 1.3 14 500 21 800 20 000 IRT 1520
TA 1825 Z 30.5 TAM 1825 32.5 ─ ─ ─ ─ ─ ─ 18 25 25 1.3 18 600 30 000 20 000 IRT 1525
TA 1916 Z 23 TAM 1916 25.5 ─ ─ ─ ─ ─ ─ 19 27 16 1.3 12 200 15 700 20 000 IRT 1516-1
19 19.000 18.987 27.012 26.991 ─ ─
TA 1920 Z 29 TAM 1920 31 ─ ─ ─ ─ ─ ─ 19 27 20 1.3 16 100 22 600 20 000 IRT 1520-1

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B11 1mm=0.03937inch
B12
 SHELL TYPE NEEDLE ROLLER BEARINGS

C C C

t2

Fw
Fw
Fw

D
D
D
TA … Z　TLA … Z TAM TLAM YT

Shaft dia. 20 − 21mm

Identification number Boundary dimensions Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft mm load rating load rating rotational inner ring
speed(1)
dia.
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
(Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) Fw D C t2 h6 J7 N7
mm g g g g g Max. Max. Min. Max. Min. Max. Min. N N min-1

─ ─ ─ ─ TLA 2012 Z 13.2 TLAM 2012 15.2 ─ ─ 20 26 12 1.3 8 740 12 900 20 000 ─
─ ─ ─ ─ TLA 2016 Z 17.8 TLAM 2016 19.9 ─ ─ 20 26 16 1.3 11 100 17 500 20 000 IRT 1716
20.000 19.987 ─ ─ 25.993 25.972
─ ─ ─ ─ TLA 2020 Z 22 TLAM 2020 24 ─ ─ 20 26 20 1.3 14 500 24 700 20 000 IRT 1720
─ ─ ─ ─ TLA 2030 Z 33 TLAM 2030 35 ─ ─ 20 26 30 1.3 22 300 42 900 20 000 IRT 1730
TA 2015 Z 20 TAM 2015 22.5 ─ ─ ─ ─ ─ ─ 20 27 15 1.3 10 400 14 600 20 000 IRT 1515-2
20 TA 2020 Z 26.5 TAM 2020 29 ─ ─ ─ ─ ─ ─ 20 27 20 1.3 15 000 23 400 20 000 IRT 1520-2
TA 2025 Z 33 TAM 2025 35.5 ─ ─ ─ ─ ─ ─ 20 27 25 1.3 19 200 32 200 20 000 IRT 1525-2
20.000 19.987 27.012 26.991 ─ ─
TA 2030 Z 39.5 TAM 2030 42 ─ ─ ─ ─ ─ ─ 20 27 30 1.3 23 100 41 000 20 000 IRT 1530-2
─ ─ ─ ─ ─ ─ ─ ─ YT 2015 23.5 20 27 15 ─ 18 400 30 900 7 500 IRT 1515-2
─ ─ ─ ─ ─ ─ ─ ─ YT 2025 41 20 27 25 ─ 30 000 58 300 7 500 IRT 1525-2
TA 202820 Z 30 TAM 202820 32.5 ─ ─ ─ ─ ─ ─ 20 28 20 1.3 16 900 24 300 20 000 IRT 1520-2
20.000 19.987 28.012 27.991 ─ ─
─ ─ ─ ─ ─ ─ ─ ─ YT 202820 37.5 20 28 20 ─ 26 800 44 600 7 500 IRT 1520-2
TA 2116 Z 25 TAM 2116 28 ─ ─ ─ ─ ─ ─ 21 29 16 1.3 13 300 18 100 19 000 IRT 1716-1
21 TA 2120 Z 31.5 TAM 2120 34.5 ─ ─ ─ ─ ─ ─ 21 29 20 1.3 17 600 25 900 19 000 IRT 1720-1
21.000 20.987 29.012 28.991 ─ ─
─ ─ ─ ─ ─ ─ ─ ─ YT 2116 31 21 29 16 ─ 22 100 35 200 7 000 IRT 1716-1
─ ─ ─ ─ ─ ─ ─ ─ YT 2120 39 21 29 20 ─ 27 500 46 800 7 000 IRT 1720-1

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B13 1mm=0.03937inch
B14
 SHELL TYPE NEEDLE ROLLER BEARINGS

C C C

t2

Fw

Fw
Fw

D
D
D
t1

TA … Z　TLA … Z TAM TLAM YT

t1 (Fw≧24)
Shaft dia. 22 − 24mm t2 (Fw≦22)

Identification number Boundary dimensions Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft mm load rating load rating rotational inner ring
speed(1)
dia.
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm
(Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) Fw D C t1，t2 h6 J7 N7
g g g g g Max. Max. Min. Max. Min. Max. Min. N N min-1

─ ─ ─ ─ TLA 2212 Z 15.6 TLAM 2212 18.1 ─ ─ 22 28 12 1.3 9 230 14 300 18 000 ─
─ ─ ─ ─ TLA 2216 Z 21.5 TLAM 2216 24 ─ ─ 22 28 16 1.3 22.000 21.987 ─ ─ 27.993 27.972 11 700 19 300 18 000 IRT 1716-2
─ ─ ─ ─ TLA 2220 Z 26.5 TLAM 2220 29 ─ ─ 22 28 20 1.3 15 300 27 300 18 000 IRT 1720-2
TA 2210 Z 15 TAM 2210 18.1 ─ ─ ─ ─ ─ ─ 22 29 10 1.3 6 650 8 500 18 000 IRT 1710-2
TA 2215 Z 21.5 TAM 2215 24.5 ─ ─ ─ ─ ─ ─ 22 29 15 1.3 11 100 16 400 18 000 IRT 1715-2
22 TA 2220 Z 29 TAM 2220 32 ─ ─ ─ ─ ─ ─ 22 29 20 1.3 22.000 21.987 29.012 28.991 ─ ─ 16 000 26 300 18 000 IRT 1720-2
TA 2225 Z 35.5 TAM 2225 38.5 ─ ─ ─ ─ ─ ─ 22 29 25 1.3 19 700 34 300 18 000 IRT 1725-2
TA 2230 Z 42.5 TAM 2230 45.5 ─ ─ ─ ─ ─ ─ 22 29 30 1.3 23 800 43 700 18 000 IRT 1730-2
TA 223016 Z 26 TAM 223016 29 ─ ─ ─ ─ ─ ─ 22 30 16 1.3 13 200 18 200 18 000 IRT 1716-2
TA 223020 Z 32.5 TAM 223020 35.5 ─ ─ ─ ─ ─ ─ 22 30 20 1.3 17 500 26 100 18 000 IRT 1720-2
22.000 21.987 30.012 29.991 ─ ─
─ ─ ─ ─ ─ ─ ─ ─ YT 223016 32 22 30 16 ─ 22 600 36 800 7 000 IRT 1716-2
─ ─ ─ ─ ─ ─ ─ ─ YT 223020 40.5 22 30 20 ─ 28 200 48 900 7 000 IRT 1720-2
TA 2420 Z 31 TAM 2420 35 ─ ─ ─ ─ ─ ─ 24 31 20 3.4 17 000 29 200 16 000 IRT 2020
TA 2428 Z 43.5 TAM 2428 47 ─ ─ ─ ─ ─ ─ 24 31 28 3.4 24.000 23.987 31.014 30.989 ─ ─ 24 500 46 700 16 000 IRT 2028
─ ─ ─ ─ ─ ─ ─ ─ YT 2428 54 24 31 28 ─ 36 800 79 900 6 500 IRT 2028
24 TA 243216 Z 28 TAM 243216 32 ─ ─ ─ ─ ─ ─ 24 32 16 3.4 14 200 20 500 16 000 IRT 2016
TA 243220 Z 35.5 TAM 243220 39 ─ ─ ─ ─ ─ ─ 24 32 20 3.4 18 800 29 400 16 000 IRT 2020
24.000 23.987 32.014 31.989 ─ ─
─ ─ ─ ─ ─ ─ ─ ─ YT 243216 34.5 24 32 16 ─ 23 700 40 100 6 500 IRT 2016
─ ─ ─ ─ ─ ─ ─ ─ YT 243220 43.5 24 32 20 ─ 29 500 53 200 6 500 IRT 2020

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B15 1mm=0.03937inch
B16
 SHELL TYPE NEEDLE ROLLER BEARINGS

C C C

t1

Fw
Fw
Fw

D
D

D
TA … Z　TLA … Z TAM TLAM YT YTL

Shaft dia. 25 − 28 mm

Identification number Boundary dimensions Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft mm load rating load rating rotational inner ring
speed(1)
dia.
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
(Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) Fw D C t1 h6 J7 N7
mm g g g g g Max. Max. Min. Max. Min. Max. Min. N N min-1

─ ─ ─ ─ TLA 2512 Z 19.7 TLAM  2512 23.5 ─ ─ 25 32 12 2.8 9 440 13 900 15 000 ─
─ ─ ─ ─ TLA 2516 Z 26 TLAM  2516 29.5 ─ ─ 25 32 16 2.8 12 800 20 500 15 000 ─
─ ─ ─ ─ TLA 2520 Z 32 TLAM  2520 36 ─ ─ 25 32 20 2.8 16 900 29 300 15 000 IRT 2020-1
25.000 24.987 ─ ─ 31.992 31.967
─ ─ ─ ─ TLA 2526 Z 41.5 TLAM  2526 45.5 ─ ─ 25 32 26 2.8 22 600 42 500 15 000 IRT 2026-1
─ ─ ─ ─ TLAW2538Z 58.5 TLAMW2538 62 ─ ─ 25 32 38 2.8 28 900 58 500 15 000 IRT 2038-1
─ ─ ─ ─ ─ ─ ─ ─ YTL 2526 51.5 25 32 26 ─ 35 000 75 800 6 000 IRT 2026-1
TA 2510 Z 19.1 TAM 2510 23 ─ ─ ─ ─ ─ ─ 25 33 10 3.4 7 990 9 900 15 000 IRT 2010-1
25 TA 2515 Z 28.5 TAM 2515 32.5 ─ ─ ─ ─ ─ ─ 25 33 15 3.4 13 400 19 300 15 000 IRT 2015-1
TA 2520 Z 36.5 TAM 2520 40.5 ─ ─ ─ ─ ─ ─ 25 33 20 3.4 25.000 24.987 33.014 32.989 ─ ─ 19 500 31 100 15 000 IRT 2020-1
TA 2525 Z 45.5 TAM 2525 49 ─ ─ ─ ─ ─ ─ 25 33 25 3.4 24 100 40 800 15 000 IRT 2025-1
TA 2530 Z 54.5 TAM 2530 58.5 ─ ─ ─ ─ ─ ─ 25 33 30 3.4 29 100 52 000 15 000 IRT 2030-1
─ ─ ─ ─ ─ ─ ─ ─ YT 2510 22.5 25 33 10 ─ 15 500 23 600 6 000 IRT 2010-1
─ ─ ─ ─ ─ ─ ─ ─ YT 2515 33 25 33 15 ─ 22 700 38 300 6 000 IRT 2015-1
25.000 24.987 33.014 32.989 ─ ─
─ ─ ─ ─ ─ ─ ─ ─ YT 2520 45 25 33 20 ─ 30 200 55 400 6 000 IRT 2020-1
─ ─ ─ ─ ─ ─ ─ ─ YT 2525 57 25 33 25 ─ 37 200 72 500 6 000 IRT 2025-1
TA 2616 Z 30.5 TAM 2616 34.5 ─ ─ ─ ─ ─ ─ 26 34 16 3.4 15 200 22 900 15 000 IRT 2216
TA 2620 Z 38 TAM 2620 42.5 ─ ─ ─ ─ ─ ─ 26 34 20 3.4 20 100 32 800 15 000 IRT 2220
26 26.000 25.987 34.014 33.989 ─ ─
─ ─ ─ ─ ─ ─ ─ ─ YT 2616 37 26 34 16 ─ 24 700 43 300 6 000 IRT 2216
─ ─ ─ ─ ─ ─ ─ ─ YT 2620 46.5 26 34 20 ─ 30 800 57 500 6 000 IRT 2220
─ ─ ─ ─ TLA 2816 Z 28.5 TLAM 2816 33.5 ─ ─ 28 35 16 2.8 13 800 23 500 13 000 ─
28.000 27.987 ─ ─ 34.992 34.967
─ ─ ─ ─ TLA 2820 Z 35.5 TLAM 2820 40.5 ─ ─ 28 35 20 2.8 18 300 33 600 13 000 IRT 2220-1
28 TA 2820 Z 45 TAM 2820 50 ─ ─ ─ ─ ─ ─ 28 37 20 3.4 21 200 32 300 13 000 IRT 2220-1
TA 2830 Z 67.5 TAM 2830 72.5 ─ ─ ─ ─ ─ ─ 28 37 30 3.4 28.000 27.987 37.014 36.989 ─ ─ 33 000 56 900 13 000 IRT 2230-1
─ ─ ─ ─ ─ ─ ─ ─ YT 2820 56.5 28 37 20 ─ 34 700 61 700 5 500 IRT 2220-1

Note(1)　　 Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　"W" in the identification number indicates that rolling elements are arranged in double rows.
2.　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and
closed end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of
bearings.

1N=0.102kgf=0.2248lbs.
B17 1mm=0.03937inch
B18
 SHELL TYPE NEEDLE ROLLER BEARINGS

C C C

t1

Fw
Fw
Fw

D
D

D
TA … Z　TLA … Z TAM TLAM YT

Shaft dia. 29 − 35mm

Identification number Boundary dimensions Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft mm load rating load rating rotational inner ring
speed(1)
dia.
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
(Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) Fw D C t1 h6 J7 N7
mm g g g g g Max. Max. Min. Max. Min. Max. Min. N N min-1

TA 2920 Z 47 TAM 2920 52 ─ ─ ─ ─ ─ ─ 29 38 20 3.4 22 000 34 200 13 000 IRT 2520

29 TA 2930 Z 70 TAM 2930 75.5 ─ ─ ─ ─ ─ ─ 29 38 30 3.4 29.000 28.987 38.014 37.989 ─ ─ 34 200 60 300 13 000 IRT 2530
─ ─ ─ ─ ─ ─ ─ ─ YT 2920 58.5 29 38 20 ─ 35 500 64 100 5 000 IRT 2520
─ ─ ─ ─ TLA 3012 Z 23.5 TLAM 3012 29 ─ ─ 30 37 12 2.8 10 400 16 600 12 000 ─
─ ─ ─ ─ TLA 3016 Z 30.5 TLAM 3016 36 ─ ─ 30 37 16 2.8 14 100 24 500 12 000 ─
─ ─ ─ ─ TLA 3018 Z 34.5 TLAM 3018 40 ─ ─ 30 37 18 2.8 16 400 29 800 12 000 ─
30.000 29.987 ─ ─ 36.992 36.967
─ ─ ─ ─ TLA 3020 Z 38 TLAM 3020 43.5 ─ ─ 30 37 20 2.8 18 600 35 100 12 000 IRT 2520-1
─ ─ ─ ─ TLA 3026 Z 49 TLAM 3026 54.5 ─ ─ 30 37 26 2.8 24 800 50 900 12 000 IRT 2526-1
30 ─ ─ ─ ─ TLAW3038 Z 69 TLAMW3038 74.5 ─ ─ 30 37 38 2.8 31 900 70 200 12 000 IRT 2538-1
TA 3013 Z 36.5 TAM 3013 42.5 ─ ─ ─ ─ ─ ─ 30 40 13 3.4 13 500 16 800 12 000 ─
TA 3015 Z 42 TAM 3015 47.5 ─ ─ ─ ─ ─ ─ 30 40 15 3.4 16 800 22 400 12 000 IRT 2515-1
TA 3020 Z 54.5 TAM 3020 60 ─ ─ ─ ─ ─ ─ 30 40 20 3.4 30.000 29.987 40.014 39.989 ─ ─ 24 500 36 300 12 000 IRT 2520-1
TA 3025 Z 68 TAM 3025 73.5 ─ ─ ─ ─ ─ ─ 30 40 25 3.4 31 600 50 300 12 000 IRT 2525-1
TA 3030 Z 80 TAM 3030 85.5 ─ ─ ─ ─ ─ ─ 30 40 30 3.4 36 700 60 700 12 000 IRT 2530-1
TA 3220 Z 57.5 TAM 3220 63.5 ─ ─ ─ ─ ─ ─ 32 42 20 3.4 25 400 38 600 11 000 IRT 2820
32 TA 3230 Z 86 TAM 3230 97.5 ─ ─ ─ ─ ─ ─ 32 42 30 3.4 32.000 31.984 42.014 41.989 ─ ─ 39 500 68 400 11 000 IRT 2830
─ ─ ─ ─ ─ ─ ─ ─ YT 3220 71.5 32 42 20 ─ 39 900 70 100 4 500 IRT 2820
─ ─ ─ ─ TLA 3512 Z 27 TLAM 3512 34.5 ─ ─ 35 42 12 2.8 11 600 20 000 10 000 IRT 3012
─ ─ ─ ─ TLA 3516 Z 35 TLAM 3516 42.5 ─ ─ 35 42 16 2.8 35.000 34.984 ─ ─ 41.992 41.967 15 700 29 600 10 000 ─
─ ─ ─ ─ TLA 3520 Z 43.5 TLAM 3520 51 ─ ─ 35 42 20 2.8 20 700 42 300 10 000 IRT 3020

35 TA 3512 Z 38.5 TAM 3512 46 ─ ─ ─ ─ ─ ─ 35 45 12 3.4 14 800 19 900 10 000 IRT 3012
TA 3515 Z 48 TAM 3515 56 ─ ─ ─ ─ ─ ─ 35 45 15 3.4 18 500 26 500 10 000 IRT 3015
TA 3520 Z 62.5 TAM 3520 70 ─ ─ ─ ─ ─ ─ 35 45 20 3.4 35.000 34.984 45.014 44.989 ─ ─ 27 000 43 100 10 000 IRT 3020
TA 3525 Z 78 TAM 3525 85.5 ─ ─ ─ ─ ─ ─ 35 45 25 3.4 34 800 59 700 10 000 IRT 3025
TA 3530 Z 97 TAM 3530 105 ─ ─ ─ ─ ─ ─ 35 45 30 3.4 40 600 72 600 10 000 IRT 3030

Note(1)　　 Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　"W" in the identification number indicates that rolling elements are arranged in double rows.
2.　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and
closed end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of
bearings.

1N=0.102kgf=0.2248lbs.
B19 1mm=0.03937inch
B20
 SHELL TYPE NEEDLE ROLLER BEARINGS

C C C

t1

Fw
Fw
Fw

D
D

D
TA … Z　TLA … Z TAM　TLAM YT

Shaft dia. 37 − 45mm

Identification number Boundary dimensions Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft mm load rating load rating rotational inner ring
speed(1)
dia.
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
(Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) Fw D C t1 h6 J7 N7
mm g g g g g Max. Max. Min. Max. Min. Max. Min. N N min-1

TA 3720 Z    64.5 TAM  3720    73 ─ ─ ─ ─ ─ ─ 37 47 20 3.4 27 800 45 400 9 500 IRT 3220
37 TA 3730 Z 101 TAM  3730 110 ─ ─ ─ ─ ─ ─ 37 47 30 3.4 37.000 36.984 47.014 46.989 ─ ─ 41 800 76 700 9 500 IRT 3230
─ ─ ─ ─ ─ ─ ─ ─ YT 3720   81 37 47 20 ─ 43 300 81 300 4 000 IRT 3220
TA 3815 Z    51 TAM  3815    60 ─ ─ ─ ─ ─ ─ 38 48 15 3.4 19 000 28 000 9 000 IRT 3215-1
TA 3820 Z   65.5 TAM  3820   74.5 ─ ─ ─ ─ ─ ─ 38 48 20 3.4 27 700 45 600 9 000 IRT 3220-1
38 TA 3825 Z    82.5 TAM 3825    96 ─ ─ ─ ─ ─ ─ 38 48 25 3.4 38.000 37.984 48.014 47.989 ─ ─ 35 600 63 100 9 000 IRT 3225-1
TA 3830 Z 104 TAM  3830 114 ─ ─ ─ ─ ─ ─ 38 48 30 3.4 43 100 80 600 9 000 IRT 3230-1
TAW 3845 Z 149 TAMW 3845 159 ─ ─ ─ ─ ─ ─ 38 48 45 3.4 55 700 112 000 9 000 IRT 3245-1
─ ─ ─ ─ TLA  4012 Z 30 TLAM  4012 40 ─ ─ 40 47 12 2.8 12 400 22 800 8 500 ─
─ ─ ─ ─ TLA  4016 Z 39 TLAM  4016 49 ─ ─ 40 47 16 2.8 40.000 39.984 ─ ─ 46.992 46.967 16 700 33 700 8 500 ─
─ ─ ─ ─ TLA  4020 Z 49 TLAM  4020 58.5 ─ ─ 40 47 20 2.8 22 100 48 200 8 500 IRT 3520
TA 4015 Z    54 TAM  4015   63.5 ─ ─ ─ ─ ─ ─ 40 50 15 3.4 19 500 29 400 8 500 IRT 3515
40 TA 4020 Z   69.5 TAM  4020    79 ─ ─ ─ ─ ─ ─ 40 50 20 3.4 28 400 47 800 8 500 IRT 3520
TA 4025 Z    86.5 TAM  4025 102 ─ ─ ─ ─ ─ ─ 40 50 25 3.4 36 600 66 200 8 500 IRT 3525
TA 4030 Z 110 TAM  4030 120 ─ ─ ─ ─ ─ ─ 40 50 30 3.4 40.000 39.984 50.014 49.989 ─ ─ 44 300 84 600 8 500 IRT 3530
TA 4040 Z 144 TAM  4040 154 ─ ─ ─ ─ ─ ─ 40 50 40 3.4 56 700 116 000 8 500 IRT 3540
─ ─ ─ ─ ─ ─ ─ ─ YT 4015   63.5 40 50 15 ─ 33 400 59 800 4 000 IRT 3515
─ ─ ─ ─ ─ ─ ─ ─ YT 4025 109 40 50 25 ─ 55 300 114 000 4 000 IRT 3525
─ ─ ─ ─ TLA  4516 Z 43.5 TLAM  4516 56 ─ ─ 45 52 16 2.8 17 800 37 800 7 500 ─
45.000 44.984 ─ ─ 51.991 51.961
─ ─ ─ ─ TLA  4520 Z 54.5 TLAM 4520 67 ─ ─ 45 52 20 2.8 23 400 54 000 7 500 IRT 4020
TA 4520 Z    77 TAM  4520    90 ─ ─ ─ ─ ─ ─ 45 55 20 3.4 30 600 54 600 7 500 IRT 4020
45 TA 4525 Z 102 TAM  4525 115 ─ ─ ─ ─ ─ ─ 45 55 25 3.4 39 400 75 600 7 500 IRT 4025
TA 4530 Z 122 TAM  4530 135 ─ ─ ─ ─ ─ ─ 45 55 30 3.4 47 700 96 600 7 500 IRT 4030
45.000 44.984 55.018 54.988 ─ ─
TA 4540 Z 161 TAM  4540 174 ─ ─ ─ ─ ─ ─ 45 55 40 3.4 61 300 133 000 7 500 IRT 4040
─ ─ ─ ─ ─ ─ ─ ─ YT 4520    96 45 55 20 ─ 47 800 98 200 3 500 IRT 4020
─ ─ ─ ─ ─ ─ ─ ─ YT 4525 122 45 55 25 ─ 59 100 129 000 3 500 IRT 4025

Note(1)　　 Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　"W" in the identification number indicates that rolling elements are arranged in double rows.
2.　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and
closed end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of
bearings.

1N=0.102kgf=0.2248lbs.
B21 1mm=0.03937inch
B22
 SHELL TYPE NEEDLE ROLLER BEARINGS

C C

t1

Fw
Fw

D
D
TA … Z　TLA … Z TAM　TLAM

Shaft dia. 50 − 62mm

Identification number Boundary dimensions Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft mm load rating load rating rotational inner ring
speed(1)
dia.
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
(Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) Fw D C t1 h6 J7 N7
mm g g g g g Max. Max. Min. Max. Min. Max. Min. N N min-1

─ ─ ─ ─ TLA  5020 Z 69 TLAM 5020    84.5 ─ ─ 50 58 20 2.8 28 800 64 100 6 500 IRT 4520
50.000 49.984 ─ ─ 57.991 57.961
─ ─ ─ ─ TLA  5025 Z 86 TLAM 5025 107 ─ ─ 50 58 25 2.8 36 900 88 400 6 500 IRT 4525
TA 5012 Z   
62.5 TAM 5012    78 ─ ─ ─ ─ ─ ─ 50 62 12 3.4 17 700 24 000 6 500 IRT 4512
TA 5015 Z    78 TAM 5015   98.5 ─ ─ ─ ─ ─ ─ 50 62 15 3.4 25 800 39 000 6 500 IRT 4515
50 TA 5020 Z 107 TAM 5020 123 ─ ─ ─ ─ ─ ─ 50 62 20 3.4 38 000 64 000 6 500 IRT 4520
TA 5025 Z 134 TAM 5025 150 ─ ─ ─ ─ ─ ─ 50 62 25 3.4 50.000 49.984 62.018 61.988 ─ ─ 49 100 89 000 6 500 IRT 4525
TA 5030 Z 161 TAM 5030 178 ─ ─ ─ ─ ─ ─ 50 62 30 3.4 59 500 114 000 6 500 IRT 4530
TA 5040 Z 210 TAM 5040 230 ─ ─ ─ ─ ─ ─ 50 62 40 3.4 76 500 157 000 6 500 IRT 4540
TAW 5045 Z 230 TAMW 5045 245 ─ ─ ─ ─ ─ ─ 50 62 45 3.4 76 700 158 000 6 500 IRT 4545
─ ─ ─ ─ TLA  5520 Z 75 TLAM 5520    98.5 ─ ─ 55 63 20 2.8 29 800 69 400 5 500 IRT 5020-1
55.000 54.981 ─ ─ 62.991 62.961
─ ─ ─ ─ TLA  5525 Z 98.5 TLAM 5525 118 ─ ─ 55 63 25 2.8 38 300 95 700 5 500 IRT 5025-1
TA 5520 Z 16
1 TAM 5520 36
1 ─ ─ ─ ─ ─ ─ 55 67 20 3.4 39 600 69 700 5 500 IRT 5020-1
55 TA 5525 Z 145 TAM 5525 165 ─ ─ ─ ─ ─ ─ 55 67 25 3.4 51 200 97 000 5 500 IRT 5025-1
TA 5530 Z 175 TAM 5530 195 ─ ─ ─ ─ ─ ─ 55 67 30 3.4 62 000 124 000 5 500 IRT 5030-1
55.000 54.981 67.018 66.988 ─ ─
TA 5540 Z 230 TAM 5540 250 ─ ─ ─ ─ ─ ─ 55 67 40 3.4 80 000 172 000 5 500 IRT 5040-1
TAW 5545 Z 250 TAMW 5545 270 ─ ─ ─ ─ ─ ─ 55 67 45 3.4 79 900 172 000 5 500 IRT 5045-1
TAW 5550 Z 280 TAMW 5550 300 ─ ─ ─ ─ ─ ─ 55 67 50 3.4 91 500 205 000 5 500 IRT 5050-1
TA 6025 Z 158 TAM 6025 82
1 ─ ─ ─ ─ ─ ─ 60 72 25 3.4 54 700 108 000 5 000 IRT 5025
TA 6030 Z 191 TAM 6030 215 ─ ─ ─ ─ ─ ─ 60 72 30 3.4 66 300 139 000 5 000 IRT 5030
60 TA 6040 Z 250 TAM 6040 275 ─ ─ ─ ─ ─ ─ 60 72 40 3.4 60.000 59.981 72.018 71.988 ─ ─ 85 700 193 000 5 000 IRT 5040
TAW 6045 Z 270 TAMW 6045 295 ─ ─ ─ ─ ─ ─ 60 72 45 3.4 85 400 193 000 5 000 IRT 5045
TAW 6050 Z 305 TAMW 6050 330 ─ ─ ─ ─ ─ ─ 60 72 50 3.4 97 800 229 000 5 000 IRT 5050
62 TA 6212 Z    78 TAM 6212 107 ─ ─ ─ ─ ─ ─ 62 74 12 3.4 62.000 61.981 74.018 73.988 ─ ─ 20 100 30 300 4 500 IRT 5212

Note(1)　　 Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　"W" in the identification number indicates that rolling elements are arranged in double rows.
2.　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and
closed end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of
bearings.

1N=0.102kgf=0.2248lbs.
B23 1mm=0.03937inch
B24
 SHELL TYPE NEEDLE ROLLER BEARINGS
C C

t1

Fw
Fw

D
D
TA … Z TAM

Shaft dia. 65 − 70mm

Identification number Boundary dimensions Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft mm load rating load rating rotational inner ring
speed(1)
dia.
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
(Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) Fw D C t1 h6 J7 N7
mm g g g g g Max. Max. Min. Max. Min. Max. Min. N N min-1

TA 6525 Z 169 TAM 6525 197 ─ ─ ─ ─ ─ ─ 65 77 25 3.4 56 500 116 000 4 000 IRT 5525
─ ─ ─ ─ ─ ─
65 TA 6530 Z TAM 6530
205 230 65 77 30 3.4 68 500 149 000 4 000 IRT 5530
65.000 64.981 77.018 76.988 ─ ─
TAW 6545 Z 290 TAMW 6545 315 ─ ─ ─ ─ ─ ─ 65 77 45 3.4 88 300 207 000 4 000 IRT 5545
TAW 6550 Z 330 TAMW 6550 355 ─ ─ ─ ─ ─ ─ 65 77 50 3.4 101 000 246 000 4 000 IRT 5550
TA 7025 Z 181 TAM 7025 215 ─ ─ ─ ─ ─ ─ 70 82 25 3.4 58 500 124 000 3 500 IRT 6025
─ ─ ─ ─ ─ ─
70 TA 7030 Z TAM 7030
220 250 70 82 30 3.4 70 900 159 000 3 500 IRT 6030
70.000 69.981 82.022 81.987 ─ ─
TA 7040 Z 290 TAM 7040 320 ─ ─ ─ ─ ─ ─ 70 82 40 3.4 92 000 222 000 3 500 IRT 6040
TAW 7050 Z 350 TAMW 7050 380 ─ ─ ─ ─ ─ ─ 70 82 50 3.4 105 000 262 000 3 500 IRT 6050

Note(1)　　 Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　"W" in the identification number indicates that rolling elements are arranged in double rows.
2.　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and
closed end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of
bearings.

1N=0.102kgf=0.2248lbs.
B25 1mm=0.03937inch
B26
 SHELL TYPE NEEDLE ROLLER BEARINGS
Inch Series
C C C

t2

Fw
Fw

Fw
D

D
D
BA … Z BHA … Z BAM BHAM YB

Shaft dia. 3.969 − 9.525mm

Identification number Boundary dimensions　mm(inch) Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft dia. load rating load rating rotational inner ring
speed(1)
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm (Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) t2
(inch) g g g g g
Fw D C h6 J7
Max. Max. Min. Max. Min. N N min-1

3.969 ─ ─ ─ ─ ─ ─ ─ ─ YB 2.5 2.5 0.64 3.969（ 5╱32 ） 7.144（ 9╱32） 3.96(.156) ─ 1 350 1 220 40 000 ─
3.969 3.961 7.152 7.137
（ 5╱32） ─ ─ ─ ─ ─ ─ ─ ─ YB 2.5 4 0.96 3.969（ 5╱32 ） 7.144（ 9╱32） 6.35(.250) ─ 2 320 2 440 40 000 ─
4.762  
─ ─ ─ ─ ─ ─ ─ ─ YB 34 1.6 4.762（ 3╱16 ） 8.731（11╱32） 6.35(.250) ─ 4.762 4.754 8.739 8.724 2 770 2 700 30 000 ─
（ 3╱16 ）
BA 44 2.1 ─ ─ ─ ─ ─ ─ ─ ─ 6.350（ 1╱ 4 ） 11.112（ 7╱16） 6.35(.250) 1 1 770 1 390 55 000 ─
─ ─ ─ ─ ─ ─ 6.350（ 1╱ 4 ） 11.112（ 7╱16） 7.92(.312) 1 ─
6.350 BA 45 Z 2.5 BAM 45 2.7 1 510 1 120 55 000
BA 47 Z 3.5 BAM 47 3.7 ─ ─ ─ ─ ─ ─ 6.350（  1╱ 4 ） 11.112（ 7╱16） 11.13(.438) 1 6.350 6.341 11.122 11.104 2 650 2 310 55 000 ─
（ 1╱4 ） 6.350（ 1╱ 4 ） 11.112（ 7╱16） 7.92(.312)
─ ─ ─ ─ ─ ─ ─ ─ YB 45 3.2 ─ 4 450 4 870 25 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 47 4.6 6.350（ 1╱ 4 ） 11.112（ 7╱16） 11.13(.438) ─ 6 320 7 650 25 000 ─
BA 55 Z 3 BAM 55 3.3 ─ ─ ─ ─ ─ ─ 7.938（ 5╱16） 12.700（ 1╱2） 7.92(.312) 1 1 880 1 560 45 000 ─
BA 56 Z 3.6 BAM 56 3.9 ─ ─ ─ ─ ─ ─ 7.938（ 5╱16） 12.700（ 1╱2） 9.52(.375) 1 2 620 2 390 45 000 ─
7.938 BA 57 Z 4.3 BAM 57 4.6 ─ ─ ─ ─ ─ ─ 7.938（ 5╱16） 12.700（ 1╱2） 11.13(.438) 1 7.938 7.929 12.710 12.692 3 310 3 220 45 000 ─
（ 5╱16 ） BA 59 Z 5.4 BAM 59 5.7 ─ ─ ─ ─ ─ ─ 7.938（ 5╱16） 12.700（ 1╱2） 14.27(.562) 1 4 190 4 360 45 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 55 3.8 7.938（ 5╱16） 12.700（ 1╱2） 7.92(.312) ─ 5 110 6 090 20 000 ─
─ ─ ─ ─ BHA 57 Z 6.3 BHAM 57 6.6 ─ ─ 7.938（ 5╱16） 14.288（ 9╱16） 11.13(.438) 1.3 7.938 7.929 14.298 14.280 4 150 3 730 45 000 ─
BA 65 Z 3.5 BAM 65 3.9 ─ ─ ─ ─ ─ ─ 9.525（ 3╱8 ） 14.288（ 9╱16） 7.92(.312) 1 2 220 2 010 40 000 ─
BA 66 Z 4.2 BAM 66 4.6 ─ ─ ─ ─ ─ ─ 9.525（ ╱8 ） 14.288（ 9╱16）
 3 9.52(.375) 1 3 090 3 080 40 000 ─
BA 68 Z 5.7 BAM 68 6.1 ─ ─ ─ ─ ─ ─ 9.525（ 3╱8 ） 14.288（ 9╱16） 12.70(.500) 1 9.525 9.516 14.298 14.280 4 190 4 560 40 000 ─
BA 69 Z 6.3 BAM 69 6.7 ─ ─ ─ ─ ─ ─ 9.525（ 3╱8 ） 14.288（ 9╱16） 14.27(.562) 1 4 940 5 630 40 000 ─
9.525 BA 610 Z 7 BAM 610 7.4 ─ ─ ─ ─ ─ ─ 9.525（ 3╱8 ） 14.288（ 9╱16） 15.88(.625) 1 5 660 6 700 40 000 ─
（ 3╱8 ） ─ ─ ─ ─ ─ ─ ─ ─ YB 64 3.4 9.525（ 3╱8 ） 14.288（ 9╱16） 6.35(.250) ─ 4 470 5 360 16 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 66 5.3 9.525（ 3╱8 ） 14.288（ 9╱16） 9.52(.375) ─ 9.525 9.516 14.298 14.280 6 920 9 410 16 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 68 7.2 9.525（ 3╱8 ） 14.288（ 9╱16） 12.70(.500) ─ 9 210 13 600 16 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 610 9.1 9.525（ 3╱8 ） 14.288（ 9╱16） 15.88(.625) ─ 11 300 17 800 16 000 ─
─ ─ ─ ─ BHA 68 Z 8.2 BHAM 68 8.6 ─ ─ 9.525（ 3╱8 ） 15.875（ 5╱8） 12.70(.500) 1.3 9.525 9.516 15.885 15.867 4 880 4 740 40 000 ─

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B27 1mm=0.03937inch
B28
 SHELL TYPE NEEDLE ROLLER BEARINGS
Inch Series
C C C

t2

Fw
Fw

Fw
D

D
D
BA … Z BHA … Z BAM BHAM YB YBH

Shaft dia. 11.112 − 12.700mm

Identification number Boundary dimensions　mm(inch) Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft dia. load rating load rating rotational inner ring
speed(1)
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm (Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) t2
(inch) g g g g g
Fw D C h6 J7
Max. Max. Min. Max. Min. N N min-1

BA 76 Z 4.8 BAM 76 5.3 ─ ─ ─ ─ ─ ─ 11.112（ 7╱16 ） 15.875（ 5╱8 ） 9.52(.375) 1 3 290 3 470 35 000 ─

BA 77 Z 5.6 BAM 77 6.2 ─ ─ ─ ─ ─ ─ 11.112（ 7╱16 ） 15.875（ 5╱8 ） 11.13(.438) 1 4 150 4 680 35 000 ─
BA 78 Z 6.4 BAM 78 7 ─ ─ ─ ─ ─ ─ 11.112（ 7╱16 ） 15.875（ 5╱8 ） 12.70(.500) 1 11.112 11.101 15.885 15.867 4 460 5 130 35 000 ─
11.112
BA 710 Z 7.9 BAM 710 8.5 ─ ─ ─ ─ ─ ─ 11.112（ 7╱16 ） 15.875（ 5╱8 ） 15.88(.625) 1 6 020 7 550 35 000 ─
（ 7╱16 ） ─ ─ ─ ─ ─ ─ ─ ─ YB 78 8.2 11.112（ 7╱16 ） 15.875（ 5╱8 ） 12.70(.500) ─ 10 100 15 900 14 000 ─
─ ─ ─ ─ BHA 78 Z 9.3 BHAM 78 10 ─ ─ 11.112（ 7╱16 ） 17.462（11╱16 ） 12.70(.500) 1.3 11.112 11.101 17.472 17.454 5 680 5 970 35 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YBH 78 10.5 11.112（ 7╱16 ） 17.462（11╱16 ） 12.70(.500) ─ 12 500 15 800 14 000 ─
BA 85 Z 4.4 BAM 85 5.2 ─ ─ ─ ─ ─ ─ 12.700（ 1╱2 ） 17.462（11╱16 ） 7.92(.312) 1 2 490 2 510 30 000 ─
BA 86 Z 5.3 BAM 86 6.1 ─ ─ ─ ─ ─ ─ 12.700（ 1╱2 ） 17.462（11╱16 ） 9.52(.375) 1 3 470 3 850 30 000 ─
BA 87 Z 6.3 BAM 87 7 ─ ─ ─ ─ ─ ─ 12.700（ 1╱2 ） 17.462（11╱16 ） 11.13(.438) 1 12.700 12.689 17.472 17.454 4 380 5 190 30 000 ─
BA 88 Z 7.2 BAM 88 7.9 ─ ─ ─ ─ ─ ─ 12.700（ 1╱2 ） 17.462（11╱16 ） 12.70(.500) 1 4 710 5 700 30 000 IRB 58
BA 810 Z 8.9 BAM 810 9.6 ─ ─ ─ ─ ─ ─ 12.700（ 1╱2 ） 17.462（11╱16 ） 15.88(.625) 1 6 350 8 380 30 000 ─
BA 812 Z 10.6 BAM 812 11.3 ─ ─ ─ ─ ─ ─ 12.700（ 1╱2） 17.462（11╱16） 19.05(.750) 1 7 840 11 000 30 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 84 4.3 12.700（ 1╱2） 17.462（11╱16） 6.35(.250) ─ 5 260 7 150 12 000 ─
12.700 ─ ─ ─ ─ ─ ─ ─ ─ YB 86 6.7 12.700（ 1╱2） 17.462（11╱16） 9.52(.375) ─ 8 150 12 600 12 000 ─
（ 1╱2 ） ─ ─ ─ ─ ─ ─ ─ ─ YB 87 7.9 12.700（ 1╱2） 17.462（11╱16） 11.13(.438) ─ 12.700 12.689 17.472 17.454 9 530 15 300 12 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 88 9.1 12.700（ 1╱2） 17.462（11╱16） 12.70(.500) ─ 10 800 18 100 12 000 IRB 58
─ ─ ─ ─ ─ ─ ─ ─ YB 810 11.5 12.700（ 1╱2） 17.462（11╱16） 15.88(.625) ─ 13 400 23 700 12 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 812 13.9 12.700（ 1╱2） 17.462（11╱16） 19.05(.750) ─ 15 800 29 300 12 000 ─
─ ─ ─ ─ BHA 87 Z 9.1 BHAM 87 9.9 ─ ─ 12.700（ 1╱2） 19.050（ 3╱4） 11.13(.438) 1.3 5 670 6 120 30 000 ─
─ ─ ─ ─ BHA 88 Z 10.4 BHAM 88 11.3 ─ ─ 12.700（ 1╱2） 19.050（ 3╱4） 12.70(.500) 1.3 6 040 6 650 30 000 IRB 58
─ ─ ─ ─ BHA 810 Z 12.5 BHAM 810 13.3 ─ ─ 12.700（ 1╱2） 19.050（ 3╱4） 15.88(.625) 1.3 12.700 12.689 19.062 19.041 8 830 10 900 30 000 ─
─ ─ ─ ─ BHA 812 Z 15 BHAM 812 15.8 ─ ─ 12.700（ 1╱2） 19.050（ 3╱4） 19.05(.750) 1.3 11 100 14 500 30 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YBH 810 16 12.700（ 1╱2） 19.050（ 3╱4） 15.88(.625) ─ 16 300 23 500 12 000 ─

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B29 1mm=0.03937inch
B30
 SHELL TYPE NEEDLE ROLLER BEARINGS
Inch Series
C C C

t2

Fw
Fw

Fw
D

D
D
BA … Z BHA … Z BAM BHAM YB YBH

Shaft dia. 14.288 − 15.875mm

Identification number Boundary dimensions　mm(inch) Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft dia. load rating load rating rotational inner ring
speed(1)
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm (Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) t2
(inch) g g g g g
Fw D C h6 J7
Max. Max. Min. Max. Min. N N min-1

BA 95 Z 4.9 BAM 95 5.8 ─ ─ ─ ─ ─ ─ 14.288（ 9╱16 ） 19.050（ 3╱4 ） 7.92( .312) 1.3 2 760 2 970 30 000 ─
BA 96 Z 5.9 BAM 96 6.8 ─ ─ ─ ─ ─ ─ 14.288（ 9╱16 ） 19.050（ 3╱4 ） 9.52( .375) 1.3 3 850 4 560 30 000 ─
BA 97 Z 6.9 BAM 97 7.8 ─ ─ ─ ─ ─ ─ 14.288（ 9╱16 ） 19.050（ 3╱4 ） 11.13( .438) 1.3 4 860 6 140 30 000 ─
BA 98 Z 7.9 BAM 98 8.9 ─ ─ ─ ─ ─ ─ 14.288（ 9╱16 ） 19.050（ 3╱4 ） 12.70( .500) 1.3 5 220 6 740 30 000 IRB 68
BA 910 Z 9.9 BAM 910 10.8 ─ ─ ─ ─ ─ ─ 14.288（ 9╱16 ） 19.050（ 3╱4 ） 15.88( .625) 1.3 14.288 14.277 19.062 19.041 7 050 9 910 30 000 ─
14.288 BA 912 Z 11.7 BAM 912 12.6 ─ ─ ─ ─ ─ ─ 14.288（ 9╱16 ） 19.050（ 3╱4 ） 19.05( .750) 1.3 8 690 13 000 30 000 IRB 612
（ 9╱16 ） ─ ─ ─ ─ ─ ─ ─ ─ YB 98 10.1 14.288（ 9╱16 ） 19.050（ 3╱4 ） 12.70( .500) ─ 11 600 20 400 11 000 IRB 68
─ ─ ─ ─ ─ ─ ─ ─ YB 910 12.7 14.288（ 9╱16 ） 19.050（ 3╱4 ） 15.88( .625) ─ 14 300 26 700 11 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 912 15.4 14.288（ 9╱16 ） 19.050（ 3╱4 ） 19.05( .750) ─ 16 800 33 000 11 000 IRB 612
─ ─ ─ ─ BHA 98 Z 11.4 BHAM 98 12.5 ─ ─ 14.288（ 9╱16 ） 20.638（13╱16 ）12.70( .500) 1.3 6 380 7 330 30 000 IRB 68
─ ─ ─ ─ BHA 910 Z 13.6 BHAM 910 14.7 ─ ─ 14.288（ 9╱16 ） 20.638（13╱16 ）15.88( .625) 1.3 14.288 14.277 20.650 20.629 9 280 11 900 30 000 ─
─ ─ ─ ─ BHA 912 Z 16.3 BHAM 912 17.4 ─ ─ 14.288（ 9╱16 ） 20.638（13╱16 ）19.05( .750) 1.3 11 600 15 900 30 000 IRB 612
BA 105 Z 5.3 BAM 105 6.5 ─ ─ ─ ─ ─ ─ 15.875（ 5╱8 ） 20.638（13╱16 ） 7.92( .312) 1.3 2 870 3 220 25 000 ─
BA 107 Z 7.6 BAM 107 8.7 ─ ─ ─ ─ ─ ─ 15.875（ 5╱8） 20.638（13╱16） 11.13( .438) 1.3 5 040 6 660 25 000 ─
BA 108 Z 8.7 BAM 108 9.9 ─ ─ ─ ─ ─ ─ 15.875（ 5╱8） 20.638（13╱16） 12.70( .500) 1.3 5 420 7 310 25 000 IRB 68-1
BA 1010 Z 10.8 BAM 1010 12 ─ ─ ─ ─ ─ ─ 15.875（ 5╱8） 20.638（13╱16） 15.88( .625) 1.3 7 320 10 700 25 000 ─
BA 1012 Z 12.9 BAM 1012 14 ─ ─ ─ ─ ─ ─ 15.875（ 5╱8） 20.638（13╱16） 19.05( .750) 1.3 15.875 15.864 20.650 20.629 9 020 14 100 25 000 IRB 612-1
BA 1014 Z 15.1 BAM 1014 16.2 ─ ─ ─ ─ ─ ─ 15.875（ 5╱8） 20.638（13╱16） 22.22( .875) 1.3 10 700 17 500 25 000 IRB 714
BA 1016 Z 17.3 BAM 1016 18.4 ─ ─ ─ ─ ─ ─ 15.875（ 5╱8） 20.638（13╱16） 25.40(1.000) 1.3 12 300 20 800 25 000 IRB 716
15.875 ─
─ ─ ─ ─ ─ ─ ─ YB 105 6.7 15.875（ 5╱8） 20.638（13╱16） 7.92( .312) ─ 7 580 12 200 9 500 ─
（ 5╱8 ） ─ ─ ─ ─ ─ ─ ─ ─ YB 108 11 15.875（ 5╱8） 20.638（13╱16） 12.70( .500) ─ 12 300 22 700 9 500 IRB 68-1
─ ─ ─ ─ ─ ─ ─ ─ YB 1012 16.9 15.875（ 5╱8） 20.638（13╱16） 19.05( .750) ─ 17 800 36 600 9 500 IRB 612-1
─ ─ ─ ─ BHA 108 Z 12.6 BHAM 108 13.9 ─ ─ 15.875（ 5╱8） 22.225（ 7╱8） 12.70( .500) 1.3 6 680 8 020 25 000 IRB 68-1
─ ─ ─ ─ BHA 1010 Z 14.9 BHAM 1010 16.2 ─ ─ 15.875（ 5╱8） 22.225（ 7╱8） 15.88( .625) 1.3 10 200 13 800 25 000 ─
─ ─ ─ ─ BHA 1012 Z 18 BHAM 1012 19.3 ─ ─ 15.875（ 5╱8） 22.225（ 7╱8） 19.05( .750) 1.3 15.875 15.864 22.237 22.216 12 700 18 500 25 000 IRB 612-1
─ ─ ─ ─ BHA 1016 Z 24 BHAM 1016 25 ─ ─ 15.875（ 5╱8） 22.225（ 7╱8） 25.40(1.000) 1.3 17 400 27 600 25 000 IRB 716
─ ─ ─ ─ ─ ─ ─ ─ YBH 108 15.3 15.875（ 5╱8） 22.225（ 7╱8） 12.70( .500) ─ 15 000 22 400 9 500 IRB 68-1

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B31 1mm=0.03937inch
B32
 SHELL TYPE NEEDLE ROLLER BEARINGS
Inch Series
C C C

t2

Fw
Fw

Fw
D

D
D
BA … Z BHA … Z BAM BHAM YB

Shaft dia. 17.462 − 19.050mm

Identification number Boundary dimensions　mm(inch) Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft dia. load rating load rating rotational inner ring
speed(1)
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm (Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) t2
(inch) g g g g g
Fw D C h6 J7
Max. Max. Min. Max. Min. N N min-1

BA 116 Z 7 BAM 116 8.4 ─ ─ ─ ─ ─ ─ 17.462（11╱16 ） 22.225（  7╱8 9.52( .375)

） 1.3 4 530 5 980 25 000 IRB 86
BA 118 Z 9.5 BAM 118 10.8 ─ ─ ─ ─ ─ ─ 17.462（11╱16 ） 22.225（  7╱8
） 12.70(
.500) 1.3 6 140 8 850 25 000 IRB 88
BA 1110 Z 11.8 BAM 1110 13.2 ─ ─ ─ ─ ─ ─ 17.462（11╱16 ） 22.225（  7╱8 15.88( .625)
） 1.3 17.462 17.451 22.237 22.216 8 280 13 000 25 000 ─
BA 1112 Z 14 BAM 1112 15.4 ─ ─ ─ ─ ─ ─ 17.462（11╱16 ） 22.225（  7╱8 19.05( .750)
） 1.3 10 200 17 000 25 000 IRB 812
17.462
─ ─ ─ ─ ─ ─ ─ ─ YB 1112 18.3 17.462（11╱16 ） 22.225（  7╱8 19.05( .750)
） ─ 18 700 40 300 8 500 IRB 812
（ 11╱16 ）
─ ─ ─ ─ BHA 117 Z 11.9 BHAM 117 13.5 ─ ─ 17.462（11╱16 ） 23.812（ 15╱16
） 11.13(
.438) 1.3 6 860 8 530 25 000 ─
─ ─ ─ ─ BHA 118 Z 13.7 BHAM 118 15.3 ─ ─ 17.462（11╱16 ） 23.812（ 15╱16
） 12.70(
.500) 1.3 7 320 9 270 25 000 IRB 88
17.462 17.451 23.824 23.803
─ ─ ─ ─ BHA 1110 Z 16 BHAM 1110 17.6 ─ ─ 17.462（11╱16 ） 23.812（ 15╱16 15.88( .625)
） 1.3 10 500 14 900 25 000 ─
─ ─ ─ ─ BHA 1112 Z 19.3 BHAM 1112 21 ─ ─ 17.462（11╱16 ） 23.812（ 15╱16 19.05( .750)
） 1.3 13 200 19 900 25 000 IRB 812
BA 126 Z 10 BAM 126 11.7 ─ ─ ─ ─ ─ ─ 19.050（ 3╱4 ） 25.400（1 ） 9.52( .375) 1.3 5 040 5 850 20 000 ─
BA 128 Z 13.5 BAM 128 15.2 ─ ─ ─ ─ ─ ─ 19.050（ 3╱4） 25.400（1 ）12.70( .500) 1.3 6 910 8 780 20 000 IRB 88-1
BA 1210 Z 17 BAM 1210 18.6 ─ ─ ─ ─ ─ ─ 19.050（ 3╱4） 25.400（1 ）15.88( .625) 1.3 9 500 13 200 20 000 IRB 810-1
19.050 19.037 25.412 25.391
BA 1212 Z 20.5 BAM 1212 22 ─ ─ ─ ─ ─ ─ 19.050（ 3╱4） 25.400（1 ）19.05( .750) 1.3 11 900 17 700 20 000 IRB 812-1
BA 1214 Z 23.5 BAM 1214 25 ─ ─ ─ ─ ─ ─ 19.050（ 3╱4） 25.400（1 ）22.22( .875) 1.3 14 200 22 200 20 000 IRB 814-1
19.050 BA 1216 Z 27 BAM 1216 28.5 ─ ─ ─ ─ ─ ─ 19.050（ 3╱4） 25.400（1 ）25.40(1.000) 1.3 16 300 26 500 20 000 IRB 816-1
（ 3╱4 ）
─ ─ ─ ─ ─ ─ ─ ─ YB 124 8.5 19.050（ 3╱4） 25.400（1 ） 6.35( .250) ─ 7 820 10 200 8 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 128 17.8 19.050（ 3╱4） 25.400（1 ）12.70( .500) ─ 16 600 26 900 8 000 IRB 88-1
19.050 19.037 25.412 25.391
─ ─ ─ ─ ─ ─ ─ ─ YB 1210 22.5 19.050（ 3╱4） 25.400（1 ）15.88( .625) ─ 20 500 35 300 8 000 IRB 810-1
─ ─ ─ ─ ─ ─ ─ ─ YB 1212 27 19.050（ 3╱4） 25.400（1 ）19.05( .750) ─ 24 100 43 400 8 000 IRB 812-1
─ ─ ─ ─ BHA 1212 Z 26.5 BHAM 1212 28.5 ─ ─ 19.050（ 3╱4） 26.988（1  1╱16） 19.05( .750) 1.3 19.050 19.037 27.000 26.979 16 600 22 600 20 000 IRB 812-1

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B33 1mm=0.03937inch
B34
 SHELL TYPE NEEDLE ROLLER BEARINGS
Inch Series
C C C

t2

Fw

Fw
Fw
D

D
t1

BA … Z BHA … Z BAM BHAM YB YBH

t1 (Fw≧22.225)
Shaft dia. 20.638 − 22.225mm t2 (Fw≦20.638)

Identification number Boundary dimensions　mm(inch) Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft dia. load rating load rating rotational inner ring
t1 speed(1)
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm (Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) t2
(inch) g g g g g
Fw D C h6 J7
Max. Max. Min. Max. Min. N N min-1

BA 136 Z 10.7 BAM 136 12.6 ─ ─ ─ ─ ─ ─ 20.638（13╱16 ）26.988（1  1╱16） 9.52( .375) 1.3 5 230 6 300 19 000 ─
BA 138 Z 14.5 BAM 138 16.4 ─ ─ ─ ─ ─ ─ 20.638（13╱16 ）26.988（1  1╱16）12.70( .500) 1.3 7 170 9 450 19 000 IRB 98
BA 1310 Z 18.2 BAM 1310 20 ─ ─ ─ ─ ─ ─ 20.638（13╱16 ）26.988（1  1╱16）15.88( .625) 1.3 9 870 14 200 19 000 IRB 910
BA 1312 Z 22 BAM 1312 23.5 ─ ─ ─ ─ ─ ─ 20.638（13╱16 ）26.988（1  1╱16）19.05( .750) 1.3 12 400 19 000 19 000 IRB 912
BA 1314 Z 25 BAM 1314 27 ─ ─ ─ ─ ─ ─ 20.638（13╱16 ）26.988（1  1╱16）22.22( .875) 1.3 20.638 20.625 27.000 26.979 14 700 23 800 19 000 IRB 914
BA 1316 Z 28.5 BAM 1316 30.5 ─ ─ ─ ─ ─ ─ 20.638（13╱16 ）26.988（1  1╱16）25.40(1.000) 1.3 16 900 28 500 19 000 IRB 916
20.638 BA 1320 Z 35.5 BAM 1320 37.5 ─ ─ ─ ─ ─ ─ 20.638（13╱16 ）26.988（1  1╱16）31.75(1.250) 1.3 21 200 38 100 19 000 IRB 920
（ 13╱16 ） ─ ─ ─ ─ ─ ─ ─ ─ YB 136 14.1 20.638（13╱16 ）26.988（1  1╱16） 9.52( .375) ─ 13 000 20 100 7 500 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 138 19.1 20.638（13╱16 ）26.988（1  1╱16）12.70( .500) ─ 17 400 29 200 7 500 IRB 98
─ ─ ─ ─ BHA 138 Z 20 BHAM 138 22.5 ─ ─ 20.638（13╱16 ）28.575（1  1╱ 8）12.70( .500) 1.3 9 500 11 200 19 000 IRB 98
─ ─ ─ ─ BHA 1310 Z 23.5 BHAM 1310 25.5 ─ ─ 20.638（13╱16 ）28.575（1  1╱ 8）15.88( .625) 1.3 13 800 18 200 19 000 IRB 910
─ ─ ─ ─ BHA 1312 Z 28.5 BHAM 1312 30.5 ─ ─ 20.638（13╱16 ）28.575（1  1╱ 8）19.05( .750) 1.3 20.638 20.625 28.587 28.566 17 300 24 400 19 000 IRB 912
─ ─ ─ ─ ─ ─ ─ ─ YBH 1310 30.5 20.638（13╱16 ）28.575（1  1╱ 8）15.88( .625) ─ 22 900 36 300 7 500 IRB 910
─ ─ ─ ─ ─ ─ ─ ─ YBH 1312 37 20.638（13╱16 ）28.575（1  1╱ 8）19.05( .750) ─ 27 200 45 300 7 500 IRB 912
BA 146 Z 11.5 BAM 146 13.8 ─ ─ ─ ─ ─ ─ 22.225（ 7╱8） 28.575（1  1╱ 8） 9.52( .375) 2.8 5 430 6 740 18 000 IRB 106
BA 148 Z 15.6 BAM 148 17.8 ─ ─ ─ ─ ─ ─ 22.225（ 7╱8） 28.575（1  1╱ 8）12.70( .500) 2.8 7 440 10 100 18 000 IRB 108
BA 1412 Z 23.5 BAM 1412 26 ─ ─ ─ ─ ─ ─ 22.225（ 7╱8） 28.575（1  1╱ 8）19.05( .750) 2.8 12 800 20 400 18 000 IRB 1012
BA 1414 Z 27 BAM 1414 29.5 ─ ─ ─ ─ ─ ─ 22.225（ 7╱8） 28.575（1  1╱ 8）22.22( .875) 2.8 15 300 25 500 18 000 IRB 1014
BA 1416 Z 31 BAM 1416 33.5 ─ ─ ─ ─ ─ ─ 22.225（ 7╱8） 28.575（1  1╱ 8）25.40(1.000) 2.8 17 600 30 500 18 000 IRB 1016
22.225 22.212 28.587 28.566
BA 1418 Z 34.5 BAM 1418 37 ─ ─ ─ ─ ─ ─ 22.225（ 7╱8） 28.575（1  1╱ 8）28.58(1.125) 2.8 19 800 35 600 18 000 ─
22.225 BA 1422 Z 42.5 BAM 1422 44.5 ─ ─ ─ ─ ─ ─ 22.225（ 7╱8） 28.575（1  1╱ 8）34.92(1.375) 2.8 24 100 45 700 18 000 IRB 1022
（ 7╱8 ） ─ ─ ─ ─ ─ ─ ─ ─ YB 148 20.5 22.225（ 7╱8） 28.575（1  1╱ 8）12.70( .500) ─ 18 100 31 400 7 000 IRB 108
─ ─ ─ ─ ─ ─ ─ ─ YB 1412 31 22.225（ 7╱8） 28.575（1  1╱ 8）19.05( .750) ─ 26 300 50 700 7 000 IRB 1012
─ ─ ─ ─ ─ ─ ─ ─ YB 1416 41.5 22.225（ 7╱8） 28.575（1  1╱ 8）25.40(1.000) ─ 33 800 70 200 7 000 IRB 1016
─ ─ ─ ─ BHA 1410 Z 25 BHAM 1410 27.5 ─ ─ 22.225（ 7╱8） 30.162（1  3╱16）15.88( .625) 3.4 14 300 19 500 18 000 ─
─ ─ ─ ─ BHA 1412 Z 30 BHAM 1412 32.5 ─ ─ 22.225（ 7╱8） 30.162（1  3╱16）19.05( .750) 3.4 18 000 26 100 18 000 IRB 1012
22.225 22.212 30.176 30.151
─ ─ ─ ─ BHA 1416 Z 39.5 BHAM 1416 42 ─ ─ 22.225（ 7╱8） 30.162（1  3╱16）25.40(1.000) 3.4 23 600 36 900 18 000 IRB 1016
─ ─ ─ ─ ─ ─ ─ ─ YBH 1412 39 22.225（ 7╱8） 30.162（1  3╱16）19.05( .750) ─ 28 200 49 000 7 000 IRB 1012
Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B35 1mm=0.03937inch
B36
 SHELL TYPE NEEDLE ROLLER BEARINGS
Inch Series
C C C

t1

Fw
Fw
Fw
D

D
BA … Z BHA … Z BAM BHAM YB YBH

Shaft dia. 23.812 − 26.988mm

Identification number Boundary dimensions　mm(inch) Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft dia. load rating load rating rotational inner ring
speed(1)
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm (Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) t1
(inch) g g g g g
Fw D C h6 J7
Max. Max. Min. Max. Min. N N min-1

23.812 BA 158 Z 16.5 BAM 158 19 ─ ─ ─ ─ ─ ─ 23.812（  15╱16 ）30.162（1  3╱16 ）12.70( .500) 2.8 8 000 11 400 16 000 ─
BA 1510 Z 20.5 BAM 1510 23 ─ ─ ─ ─ ─ ─ 23.812（  15╱16 ）30.162（1  3╱16 ）15.88( .625) 2.8 23.812 23.799 30.176 30.151 11 000 17 100 16 000 IRB 1110
（ 15╱16 ）
BA 1516 Z 33 BAM 1516 35.5 ─ ─ ─ ─ ─ ─ 23.812（  15╱16 ）30.162（1  3╱16 ）25.40(1.000) 2.8 18 900 34 300 16 000 IRB 1116
BA 166 Z 13.1 BAM 166 16 ─ ─ ─ ─ ─ ─ 25.400（1 ） 31.750（1   1╱  4 ） 9.52( .375) 2.8 6 010 8 020 15 000 ─
BA 167 Z 15.4 BAM 167 18.3 ─ ─ ─ ─ ─ ─ 25.400（1 ） 31.750（1   1╱  4 ）11.13( .438) 2.8 7 720 11 100 15 000 ─
BA 168 Z 17.7 BAM 168 20.5 ─ ─ ─ ─ ─ ─ 25.400（1 ） 31.750（1   1╱  4 ）12.70( .500) 2.8 8 240 12 000 15 000 IRB 128
BA 1610 Z 22 BAM 1610 25 ─ ─ ─ ─ ─ ─ 25.400（1 ） 31.750（1   1╱  4 ）15.88( .625) 2.8 11 300 18 100 15 000 ─
BA 1612 Z 26.5 BAM 1612 29.5 ─ ─ ─ ─ ─ ─ 25.400（1 ） 31.750（1   1╱  4 ）19.05( .750) 2.8 14 200 24 300 15 000 IRB 1212
BA 1614 Z 31 BAM 1614 33.5 ─ ─ ─ ─ ─ ─ 25.400（1 ） 31.750（1   1╱  4 ）22.22( .875) 2.8 25.400 25.387 31.764 31.739 16 900 30 400 15 000 IRB 1214
BA 1616 Z 35.5 BAM 1616 38 ─ ─ ─ ─ ─ ─ 25.400（1 ） 31.750（1   1╱  4 ）25.40(1.000) 2.8 19 400 36 300 15 000 IRB 1216
BA 1620 Z 44 BAM 1620 46.5 ─ ─ ─ ─ ─ ─ 25.400（1 ） 31.750（1   1╱  4 ）31.75(1.250) 2.8 24 400 48 500 15 000 IRB 1220
─ ─ ─ ─ ─ ─ ─ ─ YB 168 23 25.400（1 ） 31.750（1   1╱  4 ）12.70( .500) ─ 19 400 36 000 6 000 IRB 128
─ ─ ─ ─ ─ ─ ─ ─ YB 1612 34.5 25.400（1 ） 31.750（1   1╱  4 ）19.05( .750) ─ 28 200 58 000 6 000 IRB 1212
25.400 ─ ─ ─ ─ ─ ─ ─ ─ YB 1616 46.5 25.400（1 ） 31.750（1   1╱  4 ）25.40(1.000) ─ 36 300 80 300 6 000 IRB 1216
（1）
─ ─ ─ ─ BHA 168 Z 24 BHAM 168 27 ─ ─ 25.400（1 ） 33.338（1  5╱16 ）12.70( .500) 3.4 10 200 13 100 15 000 IRB 128
─ ─ ─ ─ BHA 1610 Z 28 BHAM 1610 31 ─ ─ 25.400（1 ） 33.338（1  5╱16 ）15.88( .625) 3.4 15 300 22 100 15 000 ─
─ ─ ─ ─ BHA 1612 Z 33.5 BHAM 1612 37 ─ ─ 25.400（1 ） 33.338（1  5╱16 ）19.05( .750) 3.4 19 300 29 700 15 000 IRB 1212
─ ─ ─ ─ BHA 1614 Z 39.5 BHAM 1614 42.5 ─ ─ 25.400（1 ） 33.338（1  5╱16 ）22.22( .875) 3.4 23 000 37 200 15 000 IRB 1214
─ ─ ─ ─ BHA 1616 Z 45 BHAM 1616 48 ─ ─ 25.400（1 ） 33.338（1  5╱16）25.40(1.000) 3.4 25.400 25.387 33.352 33.327 26 400 44 500 15 000 IRB 1216
─ ─ ─ ─ BHA 1620 Z 56.5 BHAM 1620 59.5 ─ ─ 25.400（1 ） 33.338（1  5╱16）31.75(1.250) 3.4 33 200 59 600 15 000 IRB 1220
─ ─ ─ ─ BHA 1624 Z 67.5 BHAM 1624 71 ─ ─ 25.400（1 ） 33.338（1  5╱16）38.10(1.500) 3.4 39 400 74 400 15 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YBH 168 29 25.400（1 ） 33.338（1  5╱16）12.70( .500) ─ 20 900 34 100 6 000 IRB 128
─ ─ ─ ─ ─ ─ ─ ─ YBH 1612 44.5 25.400（1 ） 33.338（1  5╱16）19.05( .750) ─ 30 700 56 100 6 000 IRB 1212
─ ─ ─ ─ ─ ─ ─ ─ YBH 1616 59.5 25.400（1 ） 33.338（1  5╱16）25.40(1.000) ─ 39 900 78 400 6 000 IRB 1216
26.988 BA 1710 Z 23.5 BAM 1710 26.5 ─ ─ ─ ─ ─ ─ 26.988（1  1╱16） 33.338（1  5╱16）15.88( .625) 2.8 26.988 26.975 33.352 33.327 11 600 19 200 14 000 ─
（1 1╱16 ） BA 1716 Z 37 BAM 1716 40.5 ─ ─ ─ ─ ─ ─ 26.988（1  1╱16）33.338（1  5╱16）25.40(1.000) 2.8 20 000 38 300 14 000 ─

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B37 1mm=0.03937inch
B38
 SHELL TYPE NEEDLE ROLLER BEARINGS
Inch Series
C C C

t1

Fw
Fw
Fw
D

D
BA … Z BHA … Z BAM BHAM YB

Shaft dia. 28.575 − 30.162mm

Identification number Boundary dimensions　mm(inch) Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft dia. load rating load rating rotational inner ring
speed(1)
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm (Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) t1
(inch) g g g g g
Fw D C h6 J7
Max. Max. Min. Max. Min. N N min-1

BA 186 Z 14.5 BAM 186 18.1 ─ ─ ─ ─ ─ ─ 28.575（1 1╱8）34.925（1 3╱8） 9.52(. 375) 2.8 6 330 8 910 13 000 ─
BA 188 Z 19.5 BAM 188 23 ─ ─ ─ ─ ─ ─ 28.575（1 1╱8）34.925（1 3╱8）12.70( .500) 2.8 8 680 13 400 13 000 IRB 148
BA 1812 Z 29.5 BAM 1812 33 ─ ─ ─ ─ ─ ─ 28.575（1 1╱8）34.925（1 3╱8）19.05( .750) 2.8 15 000 26 900 13 000 IRB 1412
BA 1816 Z 39 BAM 1816 42.5 ─ ─ ─ ─ ─ ─ 28.575（1 1╱8）34.925（1 3╱8）25.40(1.000) 2.8 20 500 40 300 13 000 IRB 1416
28.575 28.562 34.939 34.914
BA 1820 Z 48.5 BAM 1820 52 ─ ─ ─ ─ ─ ─ 28.575（1 1╱8）34.925（1 3╱8）31.75(1.250) 2.8 25 700 53 900 13 000 IRB 1420
28.575 ─ ─ ─ ─ ─ ─ ─ ─ YB 188 25.5 28.575（1 1╱8）34.925（1 3╱8）12.70( .500) ─ 20 700 40 500 5 500 IRB 148
（1 1╱8 ） ─ ─ ─ ─ ─ ─ ─ ─ YB 1812 38.5 28.575（1 1╱8）34.925（1 3╱8）19.05( .750) ─ 30 000 65 300 5 500 IRB 1412
─ ─ ─ ─ ─ ─ ─ ─ YB 1816 51.5 28.575（1 1╱8）34.925（1 3╱8）25.40(1.000) ─ 38 700 90 400 5 500 IRB 1416
─ ─ ─ ─ BHA 1812 Z 45 BHAM 1812 49 ─ ─ 28.575（1 1╱8）38.100（1 1╱2）19.05( .750) 3.4 22 500 32 200 13 000 IRB 1412
─ ─ ─ ─ BHA 1816 Z 60 BHAM 1816 64 ─ ─ 28.575（1 1╱8）38.100（1 1╱2）25.40(1.000) 3.4 30 900 48 600 13 000 IRB 1416
28.575 28.562 38.114 38.089
─ ─ ─ ─ BHA 1818 Z 67.5 BHAM 1818 71.5 ─ ─ 28.575（1 1╱8）38.100（1 1╱2）28.58(1.125) 3.4 34 900 56 600 13 000 ─
─ ─ ─ ─ BHA 1820 Z 73.5 BHAM 1820 78 ─ ─ 28.575（1 1╱8）38.100（1 1╱2）31.75(1.250) 3.4 37 100 61 100 13 000 IRB 1420

30.162 BA 1910 Z 32.5 BAM 1910 37.5 ─ ─ ─ ─ ─ ─ 30.162（1 3╱16）38.100（1 1╱2）15.88( .625) 2.8 15 000 22 500 12 000 ─
BA 1916 Z 52 BAM 1916 57 ─ ─ ─ ─ ─ ─ 30.162（1 3╱16）38.100（1 1╱2）25.40(1.000) 2.8 30.162 30.146 38.114 38.089 25 800 45 300 12 000 ─
（1 3╱16 ）
─ ─ ─ ─ ─ ─ ─ YB 1910 42.5 30.162（1 3╱16）38.100（1 1╱2）15.88( .625) ─ 28 400 53 600 5 000 ─

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B39 1mm=0.03937inch
B40
 SHELL TYPE NEEDLE ROLLER BEARINGS
Inch Series
C C C

t1

Fw
Fw
Fw
D

D
BA … Z BHA … Z BAM BHAM YB

Shaft dia. 31.750 − 33.338mm

Identification number Boundary dimensions　mm(inch) Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft dia. load rating load rating rotational inner ring
speed(1)
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm (Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) t1
(inch) g g g g g
Fw D C h6 J7
Max. Max. Min. Max. Min. N N min-1

BA 208 Z 21.5 BAM 208 26 ─ ─ ─ ─ ─ ─ 31.750（1 1╱4）38.100（1 1╱2 ）12.70( .500) 2.8 9 100 14 700 12 000 IRB 168
BA 2010 Z 27 BAM 2010 31.5 ─ ─ ─ ─ ─ ─ 31.750（1 1╱4）38.100（1 1╱2 ）15.88( .625) 2.8 12 500 22 200 12 000 IRB 1610
BA 2012 Z 32.5 BAM 2012 37 ─ ─ ─ ─ ─ ─ 31.750（1 1╱4）38.100（1 1╱2）19.05( .750) 2.8 31.750 31.734 38.114 38.089 15 700 29 600 12 000 IRB 1612
BA 2016 Z 43 BAM 2016 47.5 ─ ─ ─ ─ ─ ─ 31.750（1 1╱4）38.100（1 1╱2 ）25.40(1.000) 2.8 21 500 44 300 12 000 IRB 1616
BA 2020 Z 53.5 BAM 2020 58 ─ ─ ─ ─ ─ ─ 31.750（1 1╱4）38.100（1 1╱2 ）31.75(1.250) 2.8 26 900 59 200 12 000 IRB 1620
─ ─ ─ ─ ─ ─ ─ ─ YB 2010 35 31.750（1 1╱4）38.100（1 1╱2）15.88( .625) ─ 27 000 59 000 4 500 IRB 1610
31.750 ─ ─ ─ ─ ─ ─ ─ ─ YB 2012 42.5 31.750（1 1╱4）38.100（1 1╱2 ）19.05( .750) ─ 31 800 72 500 4 500 IRB 1612
（1 1╱4 ） ─ ─ ─ ─ ─ ─ ─ ─ YB 2016 57 31.750（1 1╱4）38.100（1 1╱2 ）25.40(1.000) ─ 31.750 31.734 38.114 38.089 40 900 100 000 4 500 IRB 1616
─ ─ ─ ─ ─ ─ ─ ─ YB 2018 64 31.750（1 1╱4）38.100（1 1╱2）28.58(1.125) ─ 45 300 114 000 4 500 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 2020 68 31.750（1 1╱4）38.100（1 1╱2）31.75(1.250) ─ 49 400 128 000 4 500 IRB 1620
─ ─ ─ ─ BHA 208 Z 34.5 BHAM 208 40 ─ ─ 31.750（1 1╱4）41.275（1 5╱8）12.70( .500) 3.4 13 700 17 600 12 000 IRB 168
─ ─ ─ ─ BHA 2012 Z 49.5 BHAM 2012 54.5 ─ ─ 31.750（1 1╱4）41.275（1 5╱8）19.05( .750) 3.4 24 100 36 400 12 000 IRB 1612
31.750 31.734 41.289 41.264
─ ─ ─ ─ BHA 2016 Z 66 BHAM 2016 71 ─ ─ 31.750（1 1╱4）41.275（1 5╱8）25.40(1.000) 3.4 33 200 55 000 12 000 IRB 1616
─ ─ ─ ─ BHA 2020 Z 81.5 BHAM 2020 86.5 ─ ─ 31.750（1 1╱4）41.275（1 5╱8）31.75(1.250) 3.4 40 000 69 600 12 000 IRB 1620

33.338 BA 218 Z 28.5 BAM 218 35 ─ ─ ─ ─ ─ ─ 33.338（1 5╱16）41.275（1 5╱8）12.70( .500) 2.8 11 100 15 800 11 000 IRB 168-1
BA 2110 Z 35.5 BAM 2110 41.5 ─ ─ ─ ─ ─ ─ 33.338（1 5╱16 41.275（1 5╱8）15.88( .625) 2.8 33.338 33.322 41.289 41.264 15 400 23 900 11 000 IRB 1610-1
（1 5╱16 ）
BA 2112 Z 43 BAM 2112 49 ─ ─ ─ ─ ─ ─ 33.338（1 5╱16）41.275（1 5╱8）19.05( .750) 2.8 19 300 32 100 11 000 IRB 1612-1

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B41 1mm=0.03937inch
B42
 SHELL TYPE NEEDLE ROLLER BEARINGS
Inch Series
C C C

t1

Fw
Fw
Fw
D

D
BA … Z BHA … Z BAM BHAM YB

Shaft dia. 34.925 − 38.100mm

Identification number Boundary dimensions　mm(inch) Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft dia. load rating load rating rotational inner ring
speed(1)
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm (Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) t1
(inch) g g g g g
Fw D C h6 J7
Max. Max. Min. Max. Min. N N min-1

BA 228 Z 23.5 BAM 228 29 ─ ─ ─ ─ ─ ─ 34.925（1 3╱8）41.275（1 5╱8）12.70( .500) 2.8 9 770 16 600 10 000 IRB 188
BA 2212 Z 35.5 BAM 2212 41 ─ ─ ─ ─ ─ ─ 34.925（1 3╱8）41.275（1 5╱8）19.05( .750) 2.8 16 900 33 500 10 000 IRB 1812
BA 2216 Z 47.5 BAM 2216 53 ─ ─ ─ ─ ─ ─ 34.925（1 3╱8）41.275（1 5╱8）25.40(1.000) 2.8 23 100 50 200 10 000 IRB 1816
BA 2220 Z 59 BAM 2220 64 ─ ─ ─ ─ ─ ─ 34.925（1 3╱8）41.275（1 5╱8）31.75(1.250) 2.8 34.925 34.909 41.289 41.264 28 900 67 100 10 000 IRB 1820
─ ─ ─ ─ ─ ─ ─ ─ YB 228 30.5 34.925（1 3╱8）41.275（1 5╱8）12.70( .500) ─ 23 000 49 500 4 500 IRB 188
34.925 ─ ─ ─ ─ ─ ─ ─ ─ YB 2212 46 34.925（1 3╱8）41.275（1 5╱8）19.05( .750) ─ 33 400 79 800 4 500 IRB 1812
（1 3╱8 ） ─ ─ ─ ─ ─ ─ ─ ─ YB 2220 77.5 34.925（1 3╱8）41.275（1 5╱8）31.75(1.250) ─ 52 000 141 000 4 500 IRB 1820
─ ─ ─ ─ BHA 228 Z 37 BHAM 228 43 ─ ─ 34.925（1 3╱8）44.450（1 3╱4）12.70( .500) 3.4 14 100 18 800 10 000 IRB 188
─ ─ ─ ─ BHA 2210 Z 44 BHAM 2210 50 ─ ─ 34.925（1 3╱8）44.450（1 3╱4）15.88( .625) 3.4 19 700 28 800 10 000 ─
─ ─ ─ ─ BHA 2212 Z 53 BHAM 2212 59 ─ ─ 34.925（1 3╱8）44.450（1 3╱4）19.05( .750) 3.4 34.925 34.909 44.464 44.439 24 800 38 800 10 000 IRB 1812
─ ─ ─ ─ BHA 2216 Z 71 BHAM 2216 77 ─ ─ 34.925（1 3╱8）44.450（1 3╱4）25.40(1.000) 3.4 34 100 58 400 10 000 IRB 1816
─ ─ ─ ─ BHA 2220 Z 87 BHAM 2220 98.5 ─ ─ 34.925（1 3╱8）44.450（1 3╱4）31.75(1.250) 3.4 41 200 74 200 10 000 IRB 1820
BA 248 Z 38.5 BAM 248 47.5 ─ ─ ─ ─ ─ ─ 38.100（1 1╱2）47.625（1 7╱8）12.70( .500) 2.8 12 900 17 900 9 000 ─
BA 2410 Z 48.5 BAM 2410 57.5 ─ ─ ─ ─ ─ ─ 38.100（1 1╱2）47.625（1 7╱8）15.88( .625) 2.8 17 800 27 100 9 000 IRB 2010
BA 2412 Z 58.5 BAM 2412 67.5 ─ ─ ─ ─ ─ ─ 38.100（1 1╱2）47.625（1 7╱8）19.05( .750) 2.8 22 500 36 600 9 000 ─
38.100 38.084 47.639 47.614
BA 2414 Z 69 BAM 2414 78 ─ ─ ─ ─ ─ ─ 38.100（1 1╱2）47.625（1 7╱8）22.22( .875) 2.8 26 700 45 600 9 000 IRB 2014
BA 2416 Z 79 BAM 2416 88 ─ ─ ─ ─ ─ ─ 38.100（1 1╱2）47.625（1 7╱8）25.40(1.000) 2.8 31 100 55 400 9 000 IRB 2016
38.100
BA 2420 Z 97.5 BAM 2420 106 ─ ─ ─ ─ ─ ─ 38.100（1 1╱2）47.625（1 7╱8）31.75(1.250) 2.8 39 000 74 200 9 000 IRB 2020
（1 1╱2 ）
─ ─ ─ ─ ─ ─ ─ ─ YB 246 38 38.100（1 1╱2）47.625（1 7╱8） 9.52( .375) ─ 21 000 34 100 4 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 248 51.5 38.100（1 1╱2）47.625（1 7╱8）12.70( .500) ─ 28 700 50 900 4 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 2414 91 38.100（1 1╱2）47.625（1 7╱8）22.22( .875) ─ 38.100 38.084 47.639 47.614 48 900 101 000 4 000 IRB 2014
─ ─ ─ ─ ─ ─ ─ ─ YB 2416 105 38.100（1 1╱2）47.625（1 7╱8）25.40(1.000) ─ 55 100 118 000 4 000 IRB 2016
─ ─ ─ ─ ─ ─ ─ ─ YB 2420 131 38.100（1 1╱2）47.625（1 7╱8）31.75(1.250) ─ 66 800 151 000 4 000 IRB 2020

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B43 1mm=0.03937inch
B44
 SHELL TYPE NEEDLE ROLLER BEARINGS
Inch Series
C C C

t1

Fw
Fw
Fw
D

D
BA … Z BHA … Z BAM BHAM YB

Shaft dia. 41.275 − 52.388mm

Identification number Boundary dimensions　mm(inch) Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft dia. load rating load rating rotational inner ring
speed(1)
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm (Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) t1
(inch) g g g g g
Fw D C h6 J7
Max. Max. Min. Max. Min. N N min-1

BA   268 Z 41 BAM   268 51.5 ─ ─ ─ ─ ─ ─ 41.275（1 5╱8）50.800（2　   ）12.70( .500) 2.8 13 700 19 800 8 000 ─
41.275 BA   2610 Z 52 BAM   2610 62.5 ─ ─ ─ ─ ─ ─ 41.275（1 5╱8）50.800（2　   ）15.88( .625) 2.8 18 900 30 000 8 000 IRB 2210
BA   2616 Z 85 BAM   2616 95.5 ─ ─ ─ ─ ─ ─ 41.275（1 5╱8）50.800（2　   ）25.40(1.000) 2.8 41.275 41.259 50.818 50.788 33 000 61 400 8 000 ─
（1 ╱8 ）
5
BA   2620 Z 105 BAM   2620 115 ─ ─ ─ ─ ─ ─ 41.275（1 5╱8）50.800（2　   ）31.75(1.250) 2.8 41 400 82 100 8 000 IRB 2220
─ ─ ─ ─ ─ ─ ─ ─ YB 2610   69 41.275（1 5╱8）50.800（2　   ）15.88( .625) ─ 37 000 71 700 3 500 IRB 2210
BA   2812 Z 67.5 BAM   2812 79.5 ─ ─ ─ ─ ─ ─ 44.450（1 3╱4）53.975（2 1╱8）19.05( .750) 2.8 25 200 44 500 7 500 IRB 2412
BA   2816 Z 91 BAM   2816 103 ─ ─ ─ ─ ─ ─ 44.450（1 3╱4）53.975（2 1╱8）25.40(1.000) 2.8 34 800 67 400 7 500 IRB 2416
44.450 BA   2820 Z 112 BAM   2820 125 ─ ─ ─ ─ ─ ─ 44.450（1 3╱4）53.975（2 1╱8）31.75(1.250) 2.8 44.450 44.434 53.993 53.963 43 600 90 200 7 500 ─
（1 3╱4 ）BA   2824 Z 136 BAM   2824 148 ─ ─ ─ ─ ─ ─ 44.450（1 3╱4）53.975（2 1╱8）38.10(1.500) 2.8 52 000 113 000 7 500 IRB 2424
─ ─ ─ ─ ─ ─ ─ ─ YB 2816 119 44.450（1 3╱4）53.975（2 1╱8）25.40(1.000) ─ 59 500 136 000 3 500 IRB 2416
─ ─ ─ ─ BHA 2824 Z 195 BHAM 2824 210 ─ ─ 44.450（1 3╱4）57.150（2 1╱4）38.10(1.500) 3.4 44.450 44.434 57.168 57.138 72 200 135 000 7 500 IRB 2424
BA   308 Z 47.5 BAM   308 61 ─ ─ ─ ─ ─ ─ 47.625（1 7╱8）57.150（2 1╱4）12.70( .500) 2.8 14 700 22 800 7 000 IRB 248-1
47.625 BA   3010 Z 60 BAM   3010 74 ─ ─ ─ ─ ─ ─ 47.625（1 7╱8）57.150（2 1╱4）15.88( .625) 2.8 20 300 34 500 7 000 IRB 2410-1
BA   3012 Z 72.5 BAM   3012 86.5 ─ ─ ─ ─ ─ ─ 47.625（1 7╱8）57.150（2 1╱4）19.05( .750) 2.8 47.625 47.609 57.168 57.138 25 700 46 700 7 000 ─
（1 7╱8 ）
BA   3016 Z 97.5 BAM   3016 112 ─ ─ ─ ─ ─ ─ 47.625（1 7╱8）57.150（2 1╱4）25.40(1.000) 2.8 35 400 70 600 7 000 ─
─ ─ ─ ─ ─ ─ ─ ─ YB 3012   95 47.625（1 7╱8）57.150（2 1╱4）19.05( .750) ─ 47 800 105 000 3 000 ─
BA   328 Z 50 BAM   328 66 ─ ─ ─ ─ ─ ─ 50.800（2　   ）60.325（2 3╱8）12.70( .500) 2.8 15 400 24 700 6 000 ─
BA   3216 Z 104 BAM   3216 119 ─ ─ ─ ─ ─ ─ 50.800（2　   ）60.325（2 3╱8）25.40(1.000) 2.8 37 100 76 500 6 000 IRB 2616
50.800 BA   3220 Z 128 BAM   3220 144 ─ ─ ─ ─ ─ ─ 50.800（2　   ）60.325（2 3╱8）31.75(1.250) 2.8 46 600 102 000 6 000 IRB 2720
50.800 50.781 60.343 60.313
（2） BA   3224 Z 155 BAM   3224 170 ─ ─ ─ ─ ─ ─ 50.800（2　   ）60.325（2 3╱8）38.10(1.500) 2.8 55 500 128 000 6 000 ─
BAW3228Z 180 BAMW3228 196 ─ ─ ─ ─ ─ ─ 50.800（2　   ）60.325（2 3╱8）44.45(1.750) 2.8 57 900 136 000 6 000 IRB 2628
─ ─ ─ ─ ─ ─ ─ ─ YB 3216 130 50.800（2　   ）60.325（2 3╱8）25.40(1.000) ─ 64 100 156 000 2 500 IRB 2616

52.388 ─ ─ ─ ─ BHA 3312 Z 104 BHAM 3312 122 ─ ─ 52.388（2 1╱16）64.294（2 17╱32）19.05( .750) 3.4 36 400 62 100 6 000 ─
─ ─ ─ ─ BHA 3316 Z 139 BHAM 3316 157 ─ ─ 52.388（2 1╱16）64.294（2 17╱32）25.40(1.000) 3.4 52.388 52.369 64.312 64.282 50 600 94 700 6 000 ─
（2 1╱16 ） ─ ─
─ ─ BHA 3324 Z 205 BHAM 3324 225 ─ ─ 52.388（2 1╱16）64.294（2 17╱32）38.10(1.500) 3.4 73 900 154 000 6 000 ─

Note(1)　　 Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　"W" in the identification number indicates that rolling elements are arranged in double rows.
2.　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and
closed end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of
bearings.

1N=0.102kgf=0.2248lbs.
B45 1mm=0.03937inch
B46
 SHELL TYPE NEEDLE ROLLER BEARINGS
Inch Series
C C

t1

Fw
Fw
D

D
BA … Z BAM

Shaft dia. 53.975 − 69.850mm

Identification number Boundary dimensions　mm(inch) Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft dia. load rating load rating rotational inner ring
speed(1)
Standard Mass Closed end Mass Standard Mass Closed end Mass Grease retained Mass Shaft dia. Housing bore dia. C C0
mm (Ref. ) (Ref. ) (Ref. ) (Ref. ) (Ref. ) t1
(inch) g g g g g
Fw D C h6 J7
Max. Max. Min. Max. Min. N N min-1

53.975 BA 348 Z 53 BAM 348 70.5 ─ ─ ─ ─ ─ ─ 53.975（2 1╱8） 63.500（2 1╱2） 12.70( .500) 2.8 16 100 26 600 5 500 ─
BA 3416 Z 109 BAM 3416 127 ─ ─ ─ ─ ─ ─ 53.975（2 1╱8） 63.500（2 1╱2） 25.40(1.000) 2.8 53.975 53.956 63.518 63.488 38 700 82 500 5 500 IRB 3016
（2 1╱8 ）
BA 3424 Z 162 BAM 3424 180 ─ ─ ─ ─ ─ ─ 53.975（2 1╱8） 63.500（2 1╱2） 38.10(1.500) 2.8 57 900 138 000 5 500 IRB 3024
BA 3612 Z 85.5 BAM 3612 105 ─ ─ ─ ─ ─ ─ 57.150（2 1╱4） 66.675（2 5╱8） 19.05( .750) 2.8 28 500 56 700 5 000 ─
57.150 BA 3616 Z 115 BAM 3616 135 ─ ─ ─ ─ ─ ─ 57.150（2 1╱4） 66.675（2 5╱8） 25.40(1.000) 2.8 39 300 85 700 5 000 ─
57.150 57.131 66.693 66.663
（2 1╱4 ） BA 3620 Z 143 BAM 3620 163 ─ ─ ─ ─ ─ ─ 57.150（2 1╱4） 66.675（2 5╱8） 31.75(1.250) 2.8 49 400 115 000 5 000 ─
BA 3624 Z 172 BAM 3624 192 ─ ─ ─ ─ ─ ─ 57.150（2 1╱4） 66.675（2 5╱8） 38.10(1.500) 2.8 58 800 144 000 5 000 ─
66.675  
BA 4216 Z 133 BAM 4216 161 ─ ─ ─ ─ ─ ─ 66.675（2 5╱8） 76.200（3 　 ） 25.40(1.000) 2.8 66.675 66.656 76.218 76.188 42 000 97 900 4 000 IRB 3616
（2 5╱8 ）
BA 4410 Z 85.5 BAM 4410 115 ─ ─ ─ ─ ─ ─ 69.850（2 3╱4） 79.375（3 1╱8） 15.88( .625) 2.8 25 000 50 800 3 500 ─
69.850 BA 4412 Z 103 BAM 4412 133 ─ ─ ─ ─ ─ ─ 69.850（2 3╱4） 79.375（3 1╱8） 19.05( .750) 2.8 31 500 68 700 3 500 ─
69.850 69.831 79.393 79.363
（2 3╱4 ） BA 4416 Z 139 BAM 4416 169 ─ ─ ─ ─ ─ ─ 69.850（2 3╱4） 79.375（3 1╱8） 25.40(1.000) 2.8 43 500 104 000 3 500 IRB 4016
BA 4420 Z 173 BAM 4420 205 ─ ─ ─ ─ ─ ─ 69.850（2 3╱4） 79.375（3 1╱8） 31.75(1.250) 2.8 54 600 139 000 3 500 IRB 4020

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remark　Shell Type Grease Retained Full Complement Needle Roller Bearings are provided with prepacked grease. Standard type and closed
end type bearings are not provided with prepacked grease, so perform proper lubrication when using these types of bearings.

1N=0.102kgf=0.2248lbs.
B47 1mm=0.03937inch
B48
 SHELL TYPE NEEDLE ROLLER BEARINGS
With seals C

Fw
D
TLA … UU

Shaft dia. 12 − 50mm

Mass Boundary dimensions　mm Standard mounting dimensions　mm Basic dynamic Basic static Allowable
(Ref. ) load rating load rating rotational
speed(1)
Shaft dia. Identification number Shaft dia. Housing bore dia. C C0
mm g Fw D C h6 N7
Max. Min. Max. Min. N N min-1

12 TLA 1216 UU 11.7 12 18 16 12.000 11.989 17.995 17.977 6 420 7 490 14 000
14 TLA 1416 UU 13.3 14 20 16 14.000 13.989 19.993 19.972 7 080 8 840 12 000
15 TLA 1516 UU 14 15 21 16 15.000 14.989 20.993 20.972 7 380 9 520 11 000
16 TLA 1616 UU 14.8 16 22 16 16.000 15.989 21.993 21.972 7 670 10 200 11 000
18 TLA 1816 UU 16.3 18 24 16 18.000 17.989 23.993 23.972 8 230 11 500 9 000

20 TLA 2016 UU 17.8 20 26 16 8 740 12 900 9 000

20.000 19.987 25.993 25.972
TLA 2020 UU 22.5 20 26 20 11 100 17 500 9 000

22 TLA 2216 UU 19.4 22 28 16 9 230 14 300 8 000

22.000 21.987 27.993 27.972
TLA 2220 UU 25 22 28 20 11 700 19 300 8 000

25 TLA 2516 UU 26 25 32 16 9 440 13 900 7 000

25.000 24.987 31.992 31.967
TLA 2520 UU 33 25 32 20 12 800 20 500 7 000
28 TLA 2820 UU 36.5 28 35 20 28.000 27.987 34.992 34.967 13 800 23 500 6 000

30 TLA 3016 UU 30.5 30 37 16 10 400 16 600 5 500

30.000 29.987 36.992 36.967
TLA 3020 UU 39 30 37 20 14 100 24 500 5 500

35 TLA 3516 UU 35 35 42 16 11 600 20 000 5 000

35.000 34.984 41.992 41.967
TLA 3520 UU 45 35 42 20 15 700 29 600 5 000

40 TLA 4016 UU 39.5 40 47 16 12 400 22 800 4 500

40.000 39.984 46.992 46.967
TLA 4020 UU 50.5 40 47 20 16 700 33 700 4 500
45 TLA 4520 UU 56 45 52 20 45.000 44.984 51.991 51.961 17 800 37 800 4 000
50 TLA 5026 UU 89 50 58 26 50.000 49.984 57.991 57.961 28 800 64 100 3 500

Note(1) 　Allowable rotational speed applies to grease lubrication.

Remark　The type with seals is provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
B49 1mm=0.03937inch
B50
 ■ Structure and Features Structures of Needle Roller Cages for General Usage
Needle Roller Cages for General Usage are High carbon steel cage type
bearings which display excellent rotational perfor-
mance. Needle rollers with extremely small dimen- Cage
sional variations in diameter are incorporated and
retained in their specially shaped cages with high
rigidity and accuracy, which precisely guide the nee-
C
dle rollers.
When combined with shafts and housing bores that
●High carbon steel cage type are heat treated and accurately ground as raceway
●Synthetic resin cage type surfaces, Needle Roller Cages for General Usage are
particularly useful in small spaces.
In addition, since they are lightweight and have high
rigidity as well as a large lubricant holding capacity,
Needle roller
they can withstand severe operating conditions such
as high speed rotation and shock loads, and they are
used in a wide range of applications.

Cage

Needle roller

Synthetic resin cage type

Cage

Needle roller

C1 C2
■ Types Examples of identification number ■ Fit Bc H11

Needle Roller Cages for General Usage are available Example 1 Supplemental Radial clearances of Needle Roller Cages for General

Dw
in the types shown in Table 1. Model code Dimensions code Usage are determined by the dimensional accuracy of |

2
3
For applications such as crank shafts where these KT 15 20 10 C3 the raceways and needle rollers. Table 3 shows the
bearings are difficult to install, it is also possible to recommended fits for the operating conditions.
make split type bearings. Type of bearing C

Dw
If such bearings are required, please contact .
Roller set bore diameter Table 3 R
 ecommended fits of shaft to the housing
For Needle Roller Cages for Engine Connecting Rods
（15mm） bore diameter G6 Fig.1
(KT…EG and KTV…EG), see page C17.
Shaft Tolerance class of shaft
Roller set outside diameter
Table 1 Model of bearing （20mm） Operating conditions Fw ≦ 68mm Fw ＞ 68mm
Model of bearing When high operating accuracy is required. Bc H11
Item Cage width When shock loads and oscillating motions are applied.
j5 h5
Single row needle Double row needle
（10mm）

Dw
roller roller For general use h5 g5 |

3
2
High carbon steel Tolerance of mean value of
KT KTW When the temperature is high, or mounting errors are large. g6 f6
cage type roller dia. (Refer to Table 2.)
Remark　When setting the required radial clearance according to
Synthetic resin

Dw
KT…N − the operating conditions, the clearance can easily be
cage type Example 2 obtained by selecting and matching the tolerances of
Supplemental needle rollers, shaft and housing bore. When variation of
Model code Dimensions code
the clearance does not create any problems, h6 and G7 Fig.2
■ Identification Number KT 50 58 25 N C3 are used for shaft and housing bore, respectively.

The identification number of Needle Roller Cages for

General Usage consists of a model code, dimensions
Type of bearing
■ Specifications of shaft and housing
Roller set bore diameter
and any supplemental codes. The arrangement For the raceways, a surface hardness of 58 〜 64HRC
（50mm）
examples are shown below. and a surface roughness 0.2μmRa or less are desir-
Roller set outside diameter able. However, when the operating conditions are not
（58mm） severe, a surface roughness 0.8μmRa or less can be
Cage width used.
（25mm） When the surface hardness is low, it is necessary to
correct the load rating by the hardness factor speci- Fig.3
Tolerance of mean value of
fied on page A20.
roller dia. (Refer to Table 2.)

■ Accuracy ■ Operating temperature range

The operating temperature range for high carbon
The diameter tolerances of needle rollers of Needle
steel cage types is -20 to 120°C. The maximum allow-
Roller Cages for General Usage are classified by
able temperature for synthetic resin cage types is
classification symbols shown in Table 2. If a classifi-
+110 ゜ C, and +100 ゜ C when they are continuously
cation symbol is not indicated in an identification num-
operated.
ber, the classification symbol "C3" is applied.
Fig.4
When two or more bearings are used in tandem
arrangement on the same shaft, it is necessary to
select bearings of the same classification symbol to
■ Mounting
obtain an even load distribution. The dimensions related to mounting of Needle Roller
The tolerance of the cage width Bc is -0.20 〜 -0.55 Cages for General Usage are shown in Figs. 1 and 2.
mm. When mounting Needle Roller Cages for General
Usage, they are axially positioned by using, for exam-
ple, Cir-clips for shaft and housing bore (WR and AR
Table 2 Diameter tolerances of needle rollers unit: μ m
on page L17) as shown in Figs. 3, 4 and 5.
Tolerance of mean value of needle roller For high rotational speed applications, a heat treated
Classification symbol
diameter and ground spacer is positioned between the cage Fig.5
C  3 0 〜−  3 and the cir-clip as shown in Fig. 5 so that the cage
B  2 0 〜−  2 does not make direct contact with the cir-clip. In this
case, the cir-clip is normally mounted on the non-
B  4 − 2 〜−  4
rotating side.
B  6 − 4 〜−  6
Fig. 3 shows a mounting example in the case of outer
B  8 − 6 〜−  8 ring rotation, and Figs. 4 and 5 show examples in the
− 8 〜− 10 1N=0.102kgf=0.2248lbs.
C3 B10 case of inner ring rotation.
1mm=0.03937inch
C4
 NEEDLE ROLLER CAGES FOR GENERAL USAGE

Bc

Fw
Ew
High carbon steel cage type Synthetic resin cage type
KT ( … N)

Shaft dia. 3 − 14mm

Mass Boundary dimensions Basic dynamic Basic static Allowable Mass Boundary dimensions Basic dynamic Basic static Allowable
Shaft (Ref.) mm load rating load rating rotational Shaft (Ref.) mm load rating load rating rotational
dia. Identification number C C0 speed(1) dia. Identification number C C0 speed(1)

mm g Fw Ew Bc mm g Fw Ew Bc
N N min-1 N N min-1

3 KT 367N 0.39 3 6 7 1 480 990 140 000 KT 12158   2.2 12 15 8 3 750 4 200 40 000
4 KT 477N 0.47 4 7 7 1 800 1 300 100 000 KT 121510   2.7 12 15 10 4 620 5 490 40 000
KT 121512   3.2 12 15 12 5 590 7 020 40 000
5 KT 587N 0.53 5 8 7 2 070 1 600 85 000 KT 121513   3.6 12 15 13 5 730 7 250 40 000
KT 588N 0.66 5 8 8 2 420 1 950 85 000 KT 121514   3.8 12 15 14 6 200 8 010 40 000
KT 697N 0.63 6 9 7 2 310 1 900 75 000 12 KT 121610   4 12 16 10 5 650 5 890 40 000
KT 698N 0.75 6 9 8 2 700 2 320 75 000 KT 121613   5.2 12 16 13 7 020 7 800 40 000
6 KT 121618   7 12 16 18 9 790 11 900 40 000
KT 6910 1.45 6 9 10 3 010 2 660 75 000
KT 61013 2.7 6 10 13 4 410 3 720 75 000 KT 121710   5.1 12 17 10 6 170 5 740 40 000
KT 121812   7.8 12 18 12 9 030 8 460 40 000
7 KT 7108N 0.86 7 10 8 2 960 2 690 65 000 KT 121820 13.2 12 18 20 13 700 14 400 40 000
KT 71010 1.69 7 10 10 3 340 3 130 65 000
KT 131710   4.3 13 17 10 5 990 6 500 40 000
KT 8118N 0.96 8 11 8 3 190 3 060 60 000 13 KT 131815   8.2 13 18 15 9 660 10 400 40 000
KT 81110 1.9 8 11 10 3 630 3 600 60 000 KT 131816   8.7 13 18 16 10 300 11 400 40 000
KT 81110N 1.2 8 11 10 3 630 3 600 60 000
KT 14188   3.7 14 18 8 5 110 5 410 35 000
8 KT 81113 2.5 8 12 13 4 500 4 750 60 000
KT 141810   4.6 14 18 10 6 320 7 110 35 000
KT 8128 2.1 8 12 8 3 630 3 040 60 000
KT 141811   5.2 14 18 11 6 520 7 410 35 000
KT 81211 3 8 12 11 4 630 4 170 60 000
KT 141813   6 14 18 13 7 860 9 410 35 000
KT 91210 2.1 9 12 10 3 900 4 070 55 000 KT 141816   7.3 14 18 16 9 750 12 400 35 000
14
KT 91213 2.8 9 12 13 4 840 5 370 55 000 KT 141910   5.9 14 19 10 7 130 7 180 35 000
KT 141916   9.4 14 19 16 11 100 12 600 35 000
9 KT 10138 1.9 10 13 8 3 370 3 470 50 000
KT 141918 10.5 14 19 18 12 400 14 700 35 000
KT 101310 2.3 10 13 10 4 160 4 550 50 000
KT 142012   8.7 14 20 12 9 790 9 680 35 000
KT 101313 3 10 13 13 5 160 6 000 50 000
KT 142017 12.4 14 20 17 13 300 14 400 35 000
KT 101410 3.2 10 14 10 4 900 4 680 50 000
KT 101412 3.8 10 14 12 5 940 6 000 50 000
10 KT 101413 4.2 10 14 13 6 100 6 200 50 000
KT 101415 4.8 10 14 15 7 080 7 520 50 000
11 KT 111410 2.5 11 14 10 4 400 5 020 45 000
Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.
Remark　For synthetic resin cage types, "N" is added at the end of the identification number. For sizes not listed in the dimension tables, please
contact .

1N=0.102kgf=0.2248lbs.
C5 1mm=0.03937inch
C6
 NEEDLE ROLLER CAGES FOR GENERAL USAGE

Bc

Fw
Ew
High carbon steel cage type
KT

Shaft dia. 15 − 18mm

Mass Boundary dimensions Basic dynamic Basic static Allowable Mass Boundary dimensions Basic dynamic Basic static Allowable
Shaft (Ref.) mm load rating load rating rotational Shaft (Ref.) mm load rating load rating rotational
dia. Identification number C C0 speed(1) dia. Identification number C C0 speed(1)

mm g Fw Ew Bc mm g Fw Ew Bc
N N min-1 N N min-1

KT 15199 4.4 15 19 9 6 120 6 950 35 000 KT 18228 4.7 18 22 8 6 060 7 270 30 000
KT 151910 4.9 15 19 10 6 630 7 720 35 000 KT 182210 5.8 18 22 10 7 500 9 560 30 000
KT 151911 5.5 15 19 11 6 850 8 040 35 000 KT 182213 7.6 18 22 13 9 330 12 700 30 000
15 KT 151913 6.4 15 19 13 8 250 10 200 35 000 KT 182216 9.2 18 22 16 11 600 16 700 30 000
KT 151917 8.2 15 19 17 10 900 14 600 35 000 KT 182412 11 18 24 12 11 800 13 100 30 000
KT 151918 8.7 15 19 18 11 500 15 600 35 000 KT 182416 14.8 18 24 16 15 100 17 900 30 000
KT 152010 6.3 15 20 10 7 580 7 920 35 000 18 KT 182417 15.7 18 24 17 16 000 19 400 30 000
KT 152115 11.9 15 21 15 12 600 13 500 35 000 KT 182420 18.7 18 24 20 17 900 22 400 30 000
KT 162010 5.2 16 20 10 6 930 8 330 30 000 KT 182517 18.8 18 25 17 16 700 18 600 30 000
KT 162013 6.8 16 20 13 8 620 11 000 30 000 KT 182519 21 18 25 19 18 700 21 400 30 000
KT 162016 8.3 16 20 16 10 700 14 600 30 000 KT 182522 24.5 18 25 22 20 600 24 200 30 000
KT 162017 8.7 16 20 17 11 400 15 700 30 000 KT 182614 18.1 18 26 14 14 600 14 400 30 000
KT 162118 12 16 21 18 14 000 17 700 30 000 KT 182620 26 18 26 20 20 000 21 600 30 000

16 KT 162120 13.6 16 21 20 14 700 18 900 30 000

KT 162125 16.6 16 21 25 18 300 25 100 30 000
KT 162212 9.7 16 22 12 10 500 10 900 30 000
KT 162214 11.5 16 22 14 11 600 12 500 30 000
KT 162217 13.8 16 22 17 14 200 16 100 30 000
KT 162220 16.5 16 22 20 15 900 18 600 30 000
KT 162420 23.5 16 24 20 18 500 19 000 30 000
KT 172110 5.5 17 21 10 7 220 8 950 30 000
KT 172113 7.2 17 21 13 8 980 11 800 30 000
KT 172115 8.2 17 21 15 10 400 14 400 30 000
KT 172117 9.3 17 21 17 11 800 16 900 30 000
17
KT 172220 14 17 22 20 15 500 20 500 30 000
KT 172311 9.6 17 23 11 10 100 10 500 30 000
KT 172315 13.1 17 23 15 13 300 15 100 30 000
KT 172418 18.6 17 24 18 16 500 18 000 30 000
Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.

1N=0.102kgf=0.2248lbs.
C7 1mm=0.03937inch
C8
 NEEDLE ROLLER CAGES FOR GENERAL USAGE

Bc Bc

Fw
Ew

Ew

Fw
High carbon steel cage type
KT KTW

Shaft dia. 20 − 24mm

Mass Boundary dimensions Basic dynamic Basic static Allowable Mass Boundary dimensions Basic dynamic Basic static Allowable
Shaft (Ref.) mm load rating load rating rotational Shaft (Ref.) mm load rating load rating rotational
dia. Identification number C C0 speed(1) dia. Identification number C C0 speed(1)

mm g Fw Ew Bc mm g Fw Ew Bc
N N min-1 N N min-1

KT 202410 6.3 20 24 10 7 710 10 200 25 000 KT 222610 6.9 22 26 10 8 220 11 500 25 000
KT 202413 8.3 20 24 13 9 590 13 500 25 000 KT 222613 9.1 22 26 13 10 200 15 200 25 000
KT 202417 10.6 20 24 17 12 600 19 300 25 000 KT 222617 11.6 22 26 17 13 500 21 600 25 000
KTW 202422 14.6 20 24 22 13 700 21 300 25 000 KTW 222625 17.7 22 26 25 17 100 29 400 25 000
KT 202525 19.7 20 25 25 19 900 29 800 25 000 KT 222720 17.9 22 27 20 17 400 25 700 25 000
KTW 202531.6 26.5 20 25 31.6 21 700 33 200 25 000 KT 222726 22.5 22 27 26 22 500 35 800 25 000
KTW 202540 32.5 20 25 40 27 500 44 900 25 000 KT 222817 18.4 22 28 17 17 500 23 000 25 000
KT 202611 11.1 20 26 11 11 200 12 500 25 000 22 KT 222912 16.1 22 29 12 12 900 14 000 25 000
20 KT 202612 12 20 26 12 12 400 14 300 25 000 KT 222916 21 22 29 16 17 600 20 900 25 000
KT 202614 14.2 20 26 14 13 700 16 400 25 000 KT 222917 22.5 22 29 17 18 700 22 600 25 000
KT 202617 17 20 26 17 16 800 21 200 25 000 KT 222918 23.5 22 29 18 19 800 24 400 25 000
KT 202620 20.5 20 26 20 18 700 24 400 25 000 KT 222920 26.5 22 29 20 20 900 26 100 25 000
KT 202624 24 20 26 24 22 500 30 900 25 000 KT 223015 23.5 22 30 15 17 900 19 700 25 000
KT 202627 26.5 20 26 27 26 000 37 300 25 000 KT 223230 52.5 22 32 30 36 400 42 700 25 000
KT 202814 20 20 28 14 15 700 16 100 25 000 KT 223232 56 22 32 32 38 800 46 300 25 000
KT 202820 29 20 28 20 21 500 24 200 25 000
KT 232824 22 23 28 24 21 600 34 500 20 000
KT 203225 49.5 20 32 25 30 800 30 500 25 000
KT 232913 15.1 23 29 13 13 800 17 200 20 000
23
KT 212610 8.5 21 26 10 9 090 11 000 25 000 KT 233015 21 23 30 15 17 300 20 800 20 000
21
KT 212611 9.6 21 26 11 9 390 11 500 25 000 KT 233016 22 23 30 16 18 600 22 600 20 000
KT 242813 9.9 24 28 13 10 800 16 800 20 000
KT 242816 12 24 28 16 13 400 22 200 20 000
24 KTW 242834 27 24 28 34 21 600 40 700 20 000
KT 242913 12.8 24 29 13 12 700 17 600 20 000
KT 243020 23.5 24 30 20 20 300 28 500 20 000

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.

1N=0.102kgf=0.2248lbs.
C9 1mm=0.03937inch
C10
 NEEDLE ROLLER CAGES FOR GENERAL USAGE

Bc Bc

Fw
Ew

Ew

Fw
High carbon steel cage type Synthetic resin cage type
KT ( … N) KTW

Shaft dia. 25 − 32mm

Mass Boundary dimensions Basic dynamic Basic static Allowable Mass Boundary dimensions Basic dynamic Basic static Allowable
Shaft (Ref.) mm load rating load rating rotational Shaft (Ref.) mm load rating load rating rotational
dia. Identification number C C0 speed(1) dia. Identification number C C0 speed(1)

mm g Fw Ew Bc mm g Fw Ew Bc
N N min-1 N N min-1

KT 252910 7.9 25 29 10 8 940 13 300 20 000 KT 303513 15.6 30 35 13 14 100 21 700 17 000
KT 252913 10.3 25 29 13 11 100 17 600 20 000 KT 303516 18.9 30 35 16 17 500 28 700 17 000
KT 253013 13.3 25 30 13 13 100 18 600 20 000 KT 303517 20 30 35 17 18 700 31 100 17 000
KT 253016 16.2 25 30 16 16 300 24 600 20 000 KT 303524 28.5 30 35 24 24 900 45 100 17 000
KT 253017 17.1 25 30 17 17 300 26 600 20 000 KT 303527 31.5 30 35 27 27 900 52 100 17 000
KT 253020 20 25 30 20 18 600 29 100 20 000 KT 303613 19.1 30 36 13 15 800 22 100 17 000
KT 253113 16.2 25 31 13 14 300 18 400 20 000 KT 303620 29.5 30 36 20 23 300 36 500 17 000
25 KT 253116 19.6 25 31 16 17 800 24 400 20 000 KT 303630 41.5 30 36 30 33 200 57 500 17 000
KT 253117 20.5 25 31 17 19 000 26 500 20 000 30 KT 303715 26 30 37 15 19 500 26 000 17 000
KT 253120 25 25 31 20 21 200 30 500 20 000 KT 303716 27.5 30 37 16 20 800 28 400 17 000
KT 253216 23.5 25 32 16 19 400 24 500 20 000 KT 303720 35 30 37 20 24 700 35 400 17 000
KT 253224 35 25 32 24 27 700 38 700 20 000 KT 303723 39.5 30 37 23 28 500 42 500 17 000
KT 253515 33 25 35 15 22 600 23 800 20 000 KT 303818 36.5 30 38 18 26 200 34 800 17 000
KT 253525 48 25 35 25 32 500 37 900 20 000 KT 303824 48.5 30 38 24 33 200 47 200 17 000
KT 253530 58 25 35 30 39 100 48 000 20 000 KT 304232 93 30 42 32 54 000 68 100 17 000
KTW 304237 117 30 42 37 55 900 71 300 17 000
26 KT 263013 10.7 26 30 13 11 400 18 400 19 000
KT 263832 79.5 26 38 32 47 200 55 300 19 000 KT 323713 16.7 32 37 13 14 900 23 700 16 000
KT 323717 21.5 32 37 17 19 600 33 900 16 000
KT 283313 14.8 28 33 13 13 800 20 700 18 000
KT 323723 28.5 32 37 23 24 400 44 800 16 000
KT 283317 18.9 28 33 17 18 300 29 500 18 000
KT 323813 20.5 32 38 13 16 800 24 400 16 000
KT 283327 29 28 33 27 26 300 47 300 18 000
KT 323820 31.5 32 38 20 24 800 40 300 16 000
KT 283417 23 28 34 17 20 300 29 900 18 000
28 32 KT 323916 29 32 39 16 21 600 30 200 16 000
KT 283516 26 28 35 16 20 100 26 500 18 000
KT 323920 37 32 39 20 25 600 37 700 16 000
KT 283528 44.5 28 35 28 33 200 50 600 18 000
KT 324519 63.5 32 45 19 33 700 35 900 16 000
KT 283620 38.5 28 36 20 26 500 34 700 18 000
KT 324525 84.5 32 45 25 45 600 53 000 16 000
KT 284138 110 28 41 38 58 700 71 100 18 000
KT 324532 109 32 45 32 58 500 73 000 16 000
29 KT 293825N 40.7 29 38 25 35 800 47 800 17 500
KT 324550 162 32 45 50 81 500 111 000 16 000

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.
Remark　For synthetic resin cage types, "N" is added at the end of the identification number. For sizes not listed in the dimension tables, please
contact .

1N=0.102kgf=0.2248lbs.
C11 1mm=0.03937inch
C12
 NEEDLE ROLLER CAGES FOR GENERAL USAGE

Bc Bc

Fw
Ew

Ew

Fw
High carbon steel cage type Synthetic resin cage type
KT ( … N) KTW

Shaft dia. 35 − 52mm

Mass Boundary dimensions Basic dynamic Basic static Allowable Mass Boundary dimensions Basic dynamic Basic static Allowable
Shaft (Ref.) mm load rating load rating rotational Shaft (Ref.) mm load rating load rating rotational
dia. Identification number C C0 speed(1) dia. Identification number C C0 speed(1)

mm g Fw Ew Bc mm g Fw Ew Bc
N N min-1 N N min-1

KT 354013 18.1 35 40 13 15 500 25 800 14 000 41 KT 414835 78.5 41 48 35 47 800 90 800 12 000
KT 354017 23 35 40 17 20 500 36 900 14 000
KT 424717 27.5 42 47 17 22 500 44 200 12 000
KT 354026 34.5 35 40 26 28 700 56 800 14 000
KT 424815 30 42 48 15 22 400 38 600 12 000
KT 354113 22.5 35 41 13 17 700 26 800 14 000
42 KT 424816 32 42 48 16 24 000 42 100 12 000
35 KT 354216 32 35 42 16 23 100 33 900 14 000
KT 425020 55 42 50 20 32 400 50 600 12 000
KT 354218 35.5 35 42 18 26 000 39 500 14 000
KT 425030 80.5 42 50 30 48 200 84 400 12 000
KT 354220 40.5 35 42 20 27 400 42 300 14 000
KT 354230 59 35 42 30 40 600 70 300 14 000 KT 455017 29.5 45 50 17 23 300 47 100 11 000
KT 354525 68.5 35 45 25 42 100 57 900 14 000 KT 455027 46 45 50 27 34 800 79 000 11 000
KT 455320 58 45 53 20 33 200 53 300 11 000
36 KT 364216 27.5 36 42 16 21 900 35 700 14 000
45 KT 455325 71.5 45 53 25 41 500 71 100 11 000
KT 384417 30.5 38 44 17 23 800 40 400 13 000 KT 455330 86 45 53 30 47 800 85 300 11 000
38 KT 384620 50 38 46 20 30 500 45 400 13 000 KT 455335 101 45 53 35 53 900 99 500 11 000
KT 384632 80 38 46 32 45 400 75 700 13 000 KT 455527 90.5 45 55 27 50 300 78 200 11 000
KT 404513 20.5 40 45 13 16 800 29 800 12 000
48 KT 485320 37 48 53 20 26 800 57 600 10 000
KT 404517 26.5 40 45 17 22 200 42 700 12 000 KT 485420 46 48 54 20 30 600 60 400 10 000
KT 404527 41 40 45 27 32 400 69 200 12 000
KT 505520 38.5 50 55 20 27 100 59 300 10 000
KT 404817 44 40 48 17 28 100 41 600 12 000
KT 505527 50.5 50 55 27 35 600 84 100 10 000
KT 404820 52.5 40 48 20 31 400 48 000 12 000
KT 505820 65 50 58 20 35 900 61 100 10 000
KT 404825 64.5 40 48 25 39 300 64 000 12 000
KT 505825 80 50 58 25 44 900 81 500 10 000
KT 404834 87.5 40 48 34 51 100 89 600 12 000 50
40 KT 505825N 66.3 50 58 25 51 400 97 800 10 000
KT 405015 48.5 40 50 15 28 200 35 900 12 000
KT 505830 96.5 50 58 30 51 700 97 800 10 000
KT 405017 56.5 40 50 17 30 200 39 200 12 000
KT 505835 113 50 58 35 58 300 114 000 10 000
KT 405020 61 40 50 20 35 700 48 600 12 000
KTW 405238 158 40 52 38 65 000 93 000 12 000 KT 525817 41 52 58 17 28 300 56 000   9 500
52
KT 405432 144 40 54 32 66 800 87 200 12 000 KT 526024 80 52 60 24 44 000 80 800   9 500
KT 405450 215 40 54 50 93 600 134 000 12 000
KT 405463 270 40 54 63 115 000 175 000 12 000

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.
Remark　For synthetic resin cage types, "N" is added at the end of the identification number. For sizes not listed in the dimension tables, please
contact .

1N=0.102kgf=0.2248lbs.
C13 1mm=0.03937inch
C14
 NEEDLE ROLLER CAGES FOR GENERAL USAGE

Bc

Fw
Ew
High carbon steel cage type

KT
Shaft dia. 55 − 100mm

Mass Boundary dimensions Basic dynamic Basic static Allowable Mass Boundary dimensions Basic dynamic Basic static Allowable
Shaft (Ref.) mm load rating load rating rotational Shaft (Ref.) mm load rating load rating rotational
dia. Identification number C C0 speed(1) dia. Identification number C C0 speed(1)

mm g Fw Ew Bc mm g Fw Ew Bc
N N min-1 N N min-1

KT 556020   42.5 55 60 20 28 600 66 000 9 000 KT 808822 110 80 88 22 49 700 108 000 6 000
KT 556027   55.5 55 60 27 37 600 93 900 9 000 80 KT 808825 123 80 88 25 56 400 127 000 6 000
KT 556120   52 55 61 20 32 600 68 500 9 000 KT 808830 149 80 88 30 65 000 153 000 6 000
55
KT 556315   52.5 55 63 15 29 400 48 700 9 000
KT 859112 44.5 85 91 12 25 200 56 700 6 000
KT 556320   71 55 63 20 37 400 66 400 9 000
85 KT 859325 130 85 93 25 57 800 134 000 6 000
KT 556325   87 55 63 25 46 800 88 600 9 000
KT 859330 157 85 93 30 66 600 161 000 6 000
58 KT 586320   44.5 58 63 20 29 300 69 400 8 500
90 KT 909825 138 90 98 25 60 400 145 000 5 500
KT 586420   54.5 58 64 20 33 600 72 500 8 500
KT 909830 167 90 98 30 69 600 174 000 5 500
KT 606520   45.5 60 65 20 29 700 71 100 8 500
95 KT 9510330 175 95 103 30 70 900 182 000 5 500
KT 606820   76.5 60 68 20 38 900 71 700 8 500
60 KT 606825   94 60 68 25 48 600 95 600 8 500 100 KT 10010830 184 100 108 30 72 500 191 000 4 500
KT 606827 101 60 68 27 52 400 105 000 8 500
KT 607236 205 60 72 36 86 700 152 000 8 500
63 KT 637120   79.5 63 71 20 39 500 74 400 8 000

65 KT 657320   83.5 65 73 20 41 200 79 600 7 500

KT 657330 124 65 73 30 59 300 127 000 7 500
68 KT 687620   86.5 68 76 20 41 800 82 200 7 500

70 KT 707820   89 70 78 20 42 500 84 900 7 000

KT 707830 132 70 78 30 61 200 136 000 7 000
72 KT 728020 91.5 72 80 20 43 200 87 500 7 000
KT 758320 94.5 75 83 20 43 800 90 200 6 500
KT 758325 116 75 83 25 54 800 120 000 6 500
75
KT 758330 141 75 83 30 63 100 144 000 6 500
KT 758335 164 75 83 35 71 200 168 000 6 500

Note(1) 　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.

1N=0.102kgf=0.2248lbs.
C15 1mm=0.03937inch
C16
 ■ Structure and Features Structures of Needle Roller Cages
Needle Roller Cages for Engine Connecting for Engine Connecting Rods
Rods are bearings for use in engine connecting rods.
These bearings have superior performance proven in
high performance engines of racing motor cycles, and
C
Cage
are widely used in small motor vehicles, motor cycles,
outboard marines, snow mobiles, high-speed com-
pressors, etc. and also in general-purpose engines.
●Needle Roller Cages for Big End Bearings for engine connecting rods are used under
extremely severe and complex operating conditions
●Needle Roller Cages for Small End such as heavy shock loads, high speeds, high tem-
peratures and stringent lubrication.
Needle Roller Cages for Engine Connecting Rods are
lightweight, and have high load ratings and high rigidi-
ty as well as superior wear resistance to withstand
Needle roller
these severe conditions.

■ Types
Cage
In Needle Roller Cages for Engine Connecting Rods,
the types shown in Table 1 are available.

Table 1 Types

Type For big end For small end

Model code KT…EG KTV…EG

Needle roller

C17 C18
Needle Roller Cages for Big End KT…EG Examples of identification number
Recommended radial internal clearances are shown Table 3 Recommended radial internal clearance
unit: μ m
in Table 3. When operating at high speeds, it is rec-
These roller cages are subjected to acceleration and Supplemental ommended to select the upper limit of the clearance. Shaft dia.
Model code Dimensions code
deceleration during their rotating and epicyclic motion mm Big end Small end
due to crank shaft rotation. To withstand such condi-
tions, they are made of a special alloy and are light-
KT 22 28 16 EG B2 ■ Fit Over Incl.

C
Type of bearing To obtain the recommended clearance shown in − 18 (dp −  6) 〜 dp
weight with high rigidity.
Table 3, it is general practice to match a connecting 18 30 (dp −  8) 〜 dp 3 〜 15
They are guided on their outer periphery surface with Roller set bore diameter
rod, crank pin or piston pin and needle roller cage of 30 40 (dp − 12) 〜 dp
superior lubricating properties. （22mm）
For the purpose of using them under severe condi- suitable tolerances for assembly. Remark　d p is obtained using the following equation for roller pitch
Roller set outside diameter circle diameter in millimeters, and changing the unit from
tions such as high rotational speed and stringent lubri-
（28mm）
■ Precautions for Use
millimeters to micrometers.
cation, bearings plated with non-ferrous metals are Roller pitch circle dia. = Fw ＋Ew
also available on request. Width of cage 2
When designing a connecting rod, crank pin and pis- 　　　　   Example　KT 222814 EG for big end
High-load capacity and high-rigidity cages to be used （16mm）
ton pin, the following precautions should be taken, 　　　　    　Recommended clearance is; 17 〜 25μm
for racing motor cycles (See the photo bellow.), split
Tolerance of mean value of because the raceways are subjected to loads under
needle cages for solid (one-piece) type crank-shafts roller dia. (See Table 2.) Table 4 A
 ccuracy of connecting rod, piston pin
extremely severe conditions. unit: μ m
and other special specification cages of various types and crank pin
1  Material
are also available. Please consult when Range of dia. Crank pin diameter d1 Big end bore D1
It is recommended to use carburizing steel because
Piston pin diameter d2 Small end bore D2
■ Accuracy
required. mm
the raceways are subjected to fluctuating loads with
frequent and heavy shock loads. Generally, chromi- Circularity Cylindricity Circularity Cylindricity
Over Incl.
The diameter tolerances of needle rollers of Needle um molybdenum steel is used. Nickel chromium MAX. MAX. MAX. MAX.
Roller Cages for Engine Connecting Rods are classi- molybdenum steel is also used. − 18 1 2 2 3
fied as shown in Table 2. When the classification 2  Hardness 18 30 2 3 3 4
symbol is not indicated in the identification number, The recommended surface hardness of the raceway 30 40 3 4 4 5
the classification symbol "B2" is applied. is 697〜800HV (60〜64HRC). While the effective
Remark　Refer to Fig.1 for the dimension symbols.
The tolerance of the cage width Bc is − 0.2 〜− 0.4 hardening depth differs depending on the applica-
mm. But cages with marks in the Bc column in the tions, the general value is 0.6〜1.2 mm.
High-load capacity and high-rigidity cage KTZ … EG dimension tables are manufactured with the following 3  Surface roughness
width tolerances. To minimize initial wear and to extend life, it is recom-
mended that the surface roughness of the crank pin
Needle Roller Cages for Small End KTV…EG 　　●：0 〜− 0.2 mm　　　■：− 0.1 〜− 0.3 mm and piston pin be 0.1μmRa or less, and the surface

D2

d2
roughness of the connecting rod large end and small
These roller cages oscillates at high speeds within a Table 2 Tolerances of needle roller diameter unit: μ m end bores be 0.2μmRa or less.
limited loading zone under heavy shock loads. Thus,
Classification Tolerance of mean value of 4  Accuracy
these cages are designed to be lightweight and have Class
symbol(1) roller dia. (2) Circularity and cylindricity of connecting rod, piston

L ±0.02
high rigidity with a well-balanced structure. In these
pin and crank pin are as shown in Table 4.

L
cages, a number of needle rollers having a small B  2 　0 〜−  2
Standard 5  Parallelism and torsional accuracy of connect-
diameter are incorporated to reduce the rolling con- B  4 − 2 〜−  4
ing rod bores
tact stress in the loading zone. B  6 − 4 〜−  6 L±0.02 mm and E±0.02 mm shown in Fig. 1 indi-
Needle Roller Cages for Small End are classified into Semi-standard B  8 − 6 〜−  8 cate the parallelism and torsional accuracy between

D1

d1
two types, the outer surface guide type and the inner B10 − 8 〜− 10 the big end and small end bores of the connecting
surface guide type. This classification is shown in the
Notes(1)　The classification symbol is indicated at the end of the rod, respectively. The tolerance range is 0.04 mm or
table of dimensions. identification number.
less per 100 mm in case of a general-purpose engine
In the outer surface guide type, the cage is guided by (2)　T olerances for circularity are based on JIS B 1506
(Rolling bearings - Rollers). and 0.02 mm or less for a high-speed engine such as
the sliding contact between the inner surface of the
a racing motorcycle engine. When these accuracy 100
connecting rod and the outer surface of the cage.
■ Clearance
conditions are not satisfied, the axial forces on the 50 50
In the inner surface guide type, the cage is guided by
needle roller cage and connecting rod will increase,
the sliding contact between the outer surface of the
Radial internal clearances are selected according to directly leading to a failure such as seizure. Careful
pin and the inner surface of the cage.

E ±0.02
the type of engine and the operating conditions (rota- consideration is required.

E
■ Identification Number
tional speed, load, lubricating conditions, etc.). If a
bearing is used with an inadequate clearance, bearing
The identification number of Needle Roller Cages for troubles such as seizure, early flaking and noise
increase may occur, leading to an engine failure. Fig.1
Engine Connecting Rods consists of a model code,
dimensions and any supplemental codes as shown Therefore, it is necessary to select the clearance
below. carefully according to test results and experience.

1N=0.102kgf=0.2248lbs.
C19 1mm=0.03937inch
C20
 NEEDLE ROLLER CAGES FOR ENGINE CONNECTING RODS
Needle Roller Cages for Big End Needle Roller Cages for Small End
Bc

Bc

Ew

Fw
Ew

Fw
KT … EG KTV … EG

Shaft dia. 8 − 32mm Shaft dia. 9 − 18mm

Mass Boundary dimensions Basic dynamic Basic static Mass Boundary dimensions Basic dynamic Basic static Cage guide type
Shaft (Ref.) mm load rating load rating Shaft (Ref.) mm load rating load rating
dia. Identification number C C0 dia. Identification number C C0
mm g Fw Ew Bc mm g Fw Ew Bc
N N N N

8 KT 8128 EG 2.1 8 12 8 3 280 2 660 KTV 91211.5 EG 2.8 9 12 11.5

● 3 900 4 070 Outer surface guide
9
10 KT 101410 EG 3.2 10 14 10 4 900 4 680 KTV 91214 EG 3.5 9 12 14 4 440 4 810 Inner surface guide

12 KT 121610 EG 3.8 12 16 10 5 650 5 890 KTV 101316 EG 4.5 10 13 16 4 400 4 880 Inner surface guide
KT 121710 EG 5.3 12 17 10 6 670 6 380 10 KTV 101410 EG 3.8 10 14 10 4 520 4 220 Inner surface guide
KT 14199.7 EG 5.7 14 19 9.7 6 120 5 880 KTV 101411 EG 4.1 10 14 11 5 060 4 880 Outer surface guide
14 Inner surface guide
KT 141910 EG 5.7 14 19 10 6 640 6 530 KTV 101412.5 EG 4.8 10 14 ● 12.5 5 590 5 540

15 KT 15199 EG 4.2 15 19 9 5 790 6 460 10.5 KTV 10.51415 EG 5.1 10.5 14 15 5 710 6 270 Outer surface guide
KT 152010 EG 6.1 15 20 10 7 100 7 260
KTV 121514.3 EG 4.3 12 15 ● 14.3 5 840 7 390 Outer surface guide
16 KT 162211.5 EG 9.5 16 22 ■ 11.5 9 550 9 660 12 KTV 121613 EG 5.6 12 16 13 7 020 7 800 Outer surface guide
KT 162212 EG 9.7 16 22 12 10 500 10 900 KTV 121615.5 EG 6.8 12 16 ● 15.5 7 600 8 600 Outer surface guide
KT 182210 EG 5.7 18 22 10 7 500 9 560 KTV 141812 EG 6 14 18 12 6 780 7 760 Inner surface guide
18 KT 182411.6 EG 11 18 24 ■ 11.6 10 600 11 500 14 KTV 141816.5 EG 8.2 14 18 16.5 9 180 11 500 Outer surface guide
KT 182412 EG 11 18 24 12 11 800 13 100 KTV 141822 EG 10.8 14 18 ● 22 9 950 12 600 Inner surface guide
KT 202612 EG 12 20 26 12 12 400 14 300 KTV 162019 EG 10.6 16 20 19 10 800 14 600 Outer surface guide
20 KT 202614 EG 13.8 20 26 14 13 000 15 200 16
KTV 162022 EG 12.7 16 20 22 11 400 15 700 Inner surface guide
KT 202814 EG 20 20 28 ● 14 15 700 16 100
KTV 182223.5 EG 14.9 18 22 ■ 23.5 13 000 19 300 Inner surface guide
KT 222814 EG 14.9 22 28 14 13 600 16 600 18 KTV 182321 EG 16.4 18 23 21 14 400 18 900 Inner surface guide
22 KT 222816 EG 17.5 22 28 16 15 700 19 800
KT 222912 EG 15.2 22 29 12 12 900 14 000
KT 223215 EG 30 22 32 15 21 300 21 500
23 KT 232913 EG 14.9 23 29 13 12 800 15 600
KT 243015 EG 17.9 24 30 15 14 200 18 000
24 KT 243016 EG 18.2 24 30 16 16 300 21 500
KT 243120 EG 28 24 31 20 20 800 26 400
30 KT 303818 EG 35.5 30 38 18 24 900 32 600
32 KT 324220 EG 54 32 42 20 31 900 39 400

1N=0.102kgf=0.2248lbs.
C21 1mm=0.03937inch
C22
 ■ Structure and Features
Machined Type Needle Roller Bearings are Structures of Machined Type Needle Roller Bearings
bearings with a low sectional height and large load
ratings. The outer ring has high rigidity and can easily RNA49・TAF Outer ring
be used even for light alloy housings. These bearings

●Machined Type Caged Needle Roller Bearings are available in metric series and inch series, both of
which have the caged type and the full complement
●Machined Type Guide Needle Roller Bearings
Cage
type. It is therefore possible to select a suitable bear-
ing for use under various conditions such as heavy
loads and high-speed or low-speed rotations. In addi-
tion, there are bearings with and without an inner ring. Needle roller
D
As the type without inner ring uses a shaft as the
raceway surface, a compact design is possible.

NA49・TAFI Outer ring

Cage

Inner ring

Needle roller

RNA49…UU・TAF…UU Outer ring

Needle roller

Cage

Seal

GTR
Outer ring

Mallet-shaped roller

Stop ring

D1 D2
■ Types so that the rotational accuracy is improved. Also, the
shaft rigidity can be improved as the shaft diameter ■ Identification Number
Machined Type Needle Roller Bearings are available can be increased by an amount corresponding to the The identification number of Machined Type Needle
in various types shown in Table 1. inner ring thickness. Roller Bearings consists of a model code, dimen-
sions, any supplemental codes and a classification
Caged Needle Roller Bearings with Inner Ring symbol. Examples are shown below.
Table 1.1 Type of bearing (Standard type)
This type of bearing is used when the shaft cannot be
Type Caged Needle Roller Guide Needle Roller heat-treated and finished by grinding. The outer and
Bearings Bearings inner rings are separable and a small relief clearance Examples of identification number
Series Without inner ring With inner ring Without inner ring With inner ring is provided on both sides of the inner ring raceway to
Dimension series 49 RNA 49 NA 49 facilitate bearing mounting. In the TRI and BRI
series, the width of the inner ring is larger than that of
Example 1
Model code Dimensions
Supplemental Classification
code symbol
Example 2
Model code Dimensions D
Metric series

Dimension series 69 RNA 69 NA 69

the outer ring. NA 49 05 UU C2 P6
Dimension series 48 RNA 48 NA 48 GTR GTRI BRI 24 37 16
Due to heat expansion during operation or mounting
For heavy duty TR TRI errors, the inner or outer ring may be shifted axially Type of bearing Type of bearing
For light duty TAF TAFI and the whole length of the rollers may not be in con-
Inch series BR BRI − − tact with the raceway. Therefore, attention should be Dimension series Bearing bore diameter
（24×1／16＝11／2 inches）
paid to the allowable axial shift S as shown in the
Bore diameter number
table of dimensions. Bearing outside diameter
Table 1.2 Type of bearing (With seal)
Seal symbol (With seals on both sides) （37×1／16＝25／16 inches）
Type Caged Needle Roller Guide Needle Roller
Needle Roller Bearings with Seal
Bearings Bearings Outer ring width
These bearings are sealed types of the NA49, NA69 Clearance symbol (C2 clearance)
（16×1／16＝1 inch）
Series Without inner ring With inner ring Without inner ring With inner ring and BRI series bearings, in which a seal is installed
Accuracy class
Dimension Two side seals RNA 49…UU NA 49…UU on one side (type with one seal) or both sides (type (Class 6)
Metric series

series 49 One side seal RNA 49…U NA 49…U with two seals) of the bearing. The seal is made of
− − special synthetic rubber and effectively prevents dust
Dimension Two side seals RNA 69…UU NA 69…UU
series 69 One side seal RNA 69…U NA 69…U penetration and grease leakage.

Two side seals BR　　…UU BRI　…UU − −

Inch series
One side seal − − − −
Guide Needle Roller Bearings ■ Accuracy
Machined Type Needle Roller Bearings are manufac-
These bearings are full complement type bearings
Caged Needle Roller Bearings and use mallet-shaped rollers which are guided accu-
tured based on JIS (See page A31.). The tolerances
for the smallest single roller set bore diameter of bear-
This type of bearing combines a collared outer ring rately by the guide rail located at the center of the
ings without inner ring are based on Table 14 on page
with the outer ring raceway and the guide groove of the mallet-
's unique lightweight rigid cage and A33. For BR and BRI series, the accuracy is based
needle rollers. During operation, needle rollers are shaped roller. This minimizes skewing (tilting of the
on Table 2 and the tolerances for the smallest single
guided precisely by the cage, and an ideal load distri- roller from its rotating axis), which is normally a weak
roller set bore diameter are based on Table 3.
bution is obtained. point of full complement bearings, and improves the
The metric series consists of the NA48 and NA49 rotational accuracy. This type of bearing is especially Table 2 Accuracy of inner and outer rings of inch series BR and BRII unit: μ m
suitable for heavy loads, shock loads and oscillating
series of ISO Standard, NA69 and TAFI series which d or D ∆ dmp ∆ Dmp ∆ Bs（∆ Cs） Kia Kea
are based on the international dimension series, and motions. Nominal bearing bore dia. Single plane mean Single plane mean Deviation of a single Radial runout of Radial runout of
the heavy duty TRI series which is widely used in Bearings with and without inner rings are available. In or outside dia. bore diameter outside diameter inner (or outer) ring assembled bearing assembled bearing
bearings with an inner ring, the width of the inner ring mm deviation deviation width inner ring outer ring
Japan. The TAFI series has a sectional height as low
as that of the shell type and is used for light loads. is larger than that of the outer ring. Over Incl. High Low High Low High Low Max. Max.
The inch series or BRI series is based on the specifi- − 19.050 0 − 10 − − 0 − 130 10 −
cations of ANSI Standard of USA. 19.050 30.162 0 − 13 0 − 13 0 − 130 13 15
30.162 50.800 0 − 13 0 − 13 0 − 130 15 20
Caged Needle Roller Bearings without Inner Ring 50.800 82.550 0 − 15 0 − 15 0 − 130 20 25
As shown in the section "Design of shaft and housing" 82.550 120.650 0 − 20 0 − 20 0 − 130 25 35
on page A44, any desired radial clearance can be 120.650 184.150 − − 0 − 25 0 − 130 30 45
selected by assembling this type of bearing with a Remark　d for ∆dmp, ∆Bs, ∆Cs and Kia, and D for ∆Dmp and Kea
shaft which is heat-treated and finished by grinding.
These bearings are free from the effects on dimen-
sional accuracy caused by assembling an inner ring,

1N=0.102kgf=0.2248lbs.
D3 1mm=0.03937inch
D4
Table 3 T
 olerances for smallest single roller set
bore diameter Fws min of inch series BR unit: μ m
■ Fit Table 6.2 Number of oil holes of the inner ring

Number of oil holes of the inner ring

Fw ∆ Fws min The recommended fits for Machined Type Needle Bearing type
Nominal roller set bore diameter Deviation of smallest single roller Roller Bearings are shown in Tables 22 to 24 on Nominal bearing bore diameter d   mm Standard type With seals on both sides With a seal on one side
mm set bore diameter pages A41 and A42. NA 0 0 0
Over Incl. High Low Metric series TRI 0 0 0
Caged Needle Roller
−
18.034
18.034
30.226
＋ 43
＋ 46
＋ 20
＋ 23
■ Lubrication Bearings
TAFI
d ≦ 76.200
0
1
−
1
−
−
Inch series BRI
30.226 41.910 ＋ 48 ＋ 25 Bearings with prepacked grease are shown in Table 76.200 ＜ d 2 1 −
41.910 50.038 ＋ 51 ＋ 25 5. ALVANIA GREASE S2 (SHOWA SHELL SEKIYU Guide Needle Roller Bearings Metric series GTRI 0 − −
50.038
70.104
70.104
80.010
＋ 53
＋ 58
＋ 28
＋ 28
K.K.) is prepacked as the lubricating grease.
In the case of bearings without prepacked grease,
Remark　The type with an oil hole(s) is provided with an oil groove.
D
80.010 102.108 ＋ 61 ＋ 31 perform proper lubrication. Operating them without
lubrication will increase the wear of the rolling contact
surfaces and shorten their lives.
■ Matched Set Bearings ■ Mounting
Mounting dimensions for Machined Type Needle
When using two or more Machined Type Needle
■ Clearance Table 5 Bearings with prepacked grease 〇：With prepacked grease　×：Without prepacked grease Roller Bearings adjacent to each other on the same
Roller Bearings are shown in the table of dimensions.

shaft, it is necessary to obtain an even load distribu-

Radial internal clearances of Machined Type Needle Standard With seals on With a seal
Bearing type tion. On request, a set of bearings is available, in
type both sides on one side
Roller Bearings are made to the CN clearance shown
RNA、NA × 〇 × which bearings are matched to obtain an even load
in Table 18 on page A37. Radial internal clearances Caged Metric
Needle TR、TRI × − − distribution.
of BRI series are based on Table 4. Roller
series
TAF、TAFI、TAF/SG × − −
Bearings Inch series BR、BRI × 〇 −
Guide Needle Metric
■ Extended Life Specification Machined Type Needle Roller Bearings
Table 4 Radial internal clearance of GTR、GTRI × − −
Roller Bearings series
inch series BRI unit: μ m

Fw
■ Oil Hole
Extended Life Specification Machined Type Needle
Nominal roller set bore diameter Radial internal clearance
Roller Bearings are treated with a newly developed
mm
Table 6.1 shows the number of oil holes of the outer special heat treatment that enhances the bearing's
Over Incl. Min. Max.
ring and Table 6.2 shows the number of oil holes of surface hardness and toughness, and suppresses the
− 18.034 33 66 generation and growth of damage on the surface.
the inner ring.
18.034 25.908 41 76 Significant life extension can be achieved under high
When an outer ring with an oil hole is especially
25.908 30.226 46 82 load or under the condition of lubrication contaminated
required for the type without an oil hole, add "−OH"
30.226 35.052 48 86 with foreign substances.
before the clearance symbol in the identification num-
35.052 41.910 50 89 In a life comparison test, as shown in Figure 1, 's
ber. When an outer ring with an oil hole and an oil
41.910 50.038 50 92 special heat treated Extended Life Specification
groove is required for the type without an oil hole,
50.038 70.104 56 99 products lasted 5 times longer than standard heat-
attach "−OG" before the clearance symbol.
70.104 80.010 56 104 treated products.
Example: TAFI 203216 − OH C2 P6
80.010 100.076 63 117 Extended Life Specification Machined Type Needle
When an outer ring with multiple oil holes or an inner
100.076 102.108 68 127 Roller Bearings, available according to the "Applicable
ring with an oil hole(s) is required, please consult
Standard heat-treated products
Production Size" shown in Table 7, are made to order
. Extended life specification products

Cumulative damage rate %

upon request.

Table 7 Applicable Production Size

Table 6.1 Number of oil holes of the outer ring

Number of oil holes of the outer ring

Bearing type
Nominal roller set bore diameter  Fw   mm Standard type With seals on both sides With a seal on one side Model number : NA4904

Fw
d
Load : 10,500 N
RNA，NA 1 1 1 Lubrication : Cleaning oil lubricated

TR，TRI 1 − −
Metric series
Caged Needle Roller 　　　       Fw ≦ 26 0 − − Life h
TAF，TAFI
Bearings    26 ＜ Fw 1 − − With inner ring Without inner ring Fig. 1 Life Test Result
Fw ≦ 69.850 1 1 − d =10 ～ 75mm Fw =14 ～ 85mm Remark　This table shows the result of life testing under
Inch series BR，BRI
69.850 ＜ Fw 2 1 − NA 4900 ～ 4915 RNA 4900 ～ 4915
NA 6901 ～ 6915 RNA 6901 ～ 6915
load conditions at 50% of the basic dynamic rating.
Guide Needle Roller Bearings Metric series GTR，GTRI 1 − −
TAFI 102216 ～ 7510535 TAF 142216 ～ 8510535 The Extended Life Specification with special heat
Remark　The type with an oil hole(s) is provided with an oil groove.
TRI 153320 ～ 7510845 TR 203320 ～ 8310845 treatment lasted 5 times longer or more in L10 life
compared to the standard heat-treated products.

1N=0.102kgf=0.2248lbs.
D5 1mm=0.03937inch
D6
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C

Fw
D

Da
r
D
RNA49  TAF
RNA69（Fw ≦ 35）

Shaft dia. 5 − 15mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimension load rating load rating rotational
Da speed(2)
dia.
RNA 49 RNA 69 RNA 48 TAF TR GTR (1)
C C0
mm g Fw D C rs min Max.
mm N N min-1

─ ─ ─ TAF   51010 ─ ─   3.4 5 10 10 0.2 8.4 2 420 1 950 80 000

5 ─ ─ ─ TAF   51012 ─ ─   4.2 5 10 12 0.2 8.4 3 080 2 660 80 000
RNA   493 ─ ─ ─ ─ ─   4.6 5 11 10 0.15 9.8 2 420 1 950 80 000
─ ─ ─ ─ ─
6 RNA   494
  5.3 6 12 10 0.15 10.8 2 700 2 320 70 000
─ ─ ─ TAF   61212 ─ ─   6.4 6 12 12 0.2 10.4 3 440 3 170 70 000
RNA   495 ─ ─ ─ ─ ─   5.9 7 13 10 0.15 11.8 2 960 2 690 60 000
7 ─ ─ ─ TAF   71410 ─ ─   6.9 7 14 10 0.2 12.4 3 600 2 960 60 000
─ ─ ─ TAF   71412 ─ ─   8.3 7 14 12 0.2 12.4 4 610 4 050 60 000
RNA   496 ─ ─ ─ ─ ─   7.4 8 15 10 0.15 13.8 3 960 3 420 50 000
8 ─ ─ ─ TAF   81512 ─ ─   9.1 8 15 12 0.2 13.4 5 060 4 690 50 000
─ ─ ─ TAF   81516 ─ ─ 12.9 8 15 16 0.2 13.4 7 080 7 220 50 000
─ ─ ─ TAF   91612 ─ ─   9.8 9 16 12 0.2 14.4 5 490 5 330 45 000
9 ─ ─ ─ TAF   91616 ─ ─ 13.2 9 16 16 0.2 14.4 7 680 8 210 45 000
RNA   497 ─ ─ ─ ─ ─   9.3 9 17 10 0.15 15.8 4 530 3 650 45 000
─ ─ ─ TAF 101712 ─ ─ 10.7 10 17 12 0.2 15.4 5 880 5 970 40 000
10 ─ ─ ─ TAF 101716 ─ ─ 14.3 10 17 16 0.2 15.4 8 230 9 190 40 000
RNA   498 ─ ─ ─ ─ ─ 12.6 10 19 11 0.2 17.4 6 180 5 030 40 000
─ ─ ─ TAF 121912 ─ ─ 12.2 12 19 12 0.3 17 6 610 7 260 35 000
12 ─ ─ ─ TAF 121916 ─ ─ 16.3 12 19 16 0.3 17 9 250 11 200 35 000
RNA   499 ─ ─ ─ ─ ─ 13.6 12 20 11 0.3 18 6 600 6 310 35 000
RNA 4900 ─ ─ ─ ─ ─ 16.5 14 22 13 0.3 20 9 230 10 100 30 000
14 ─ ─ ─ TAF 142216 ─ ─ 21 14 22 16 0.3 20 11 700 13 700 30 000
─ ─ ─ TAF 142220 ─ ─ 26.5 14 22 20 0.3 20 14 800 18 600 30 000
─ ─ ─ TAF 152316 ─ ─ 22.5 15 23 16 0.3 21 12 300 14 900 30 000
15
─ ─ ─ TAF 152320 ─ ─ 28 15 23 20 0.3 21 15 600 20 200 30 000

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　TAF series with a roller set bore diameter Fw of 26 mm or less have no oil hole. In others, the outer ring has an oil groove and an
oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D7 1mm=0.03937inch
D8
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C C

r r

Fw

Fw
D

Da
D
r r
D
RNA49  TAF  TR GTR
RNA69（Fw ≦ 35）

Shaft dia. 16 − 22mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimension load rating load rating rotational
Da speed(2)
dia.
RNA 49 RNA 69 RNA 48 TAF TR GTR (1)
C C0
mm g Fw D C rs min Max.
mm N N min-1

RNA 4901 ─ ─ ─ ─ ─ 18.1 16 24 13 0.3 22 9 660 11 100 25 000

─ ─ ─ TAF 162416 ─ ─ 23 16 24 16 0.3 22 12 300 15 100 25 000
16
─ ─ ─ TAF 162420 ─ ─ 29 16 24 20 0.3 22 15 500 20 400 25 000
─ RNA 6901 ─ ─ ─ ─ 30 16 24 22 0.3 22 17 100 23 000 25 000
─ ─ ─ TAF 172516 ─ ─ 24.5 17 25 16 0.3 23 12 900 16 300 25 000
17
─ ─ ─ TAF 172520 ─ ─ 30.5 17 25 20 0.3 23 16 300 22 000 25 000
RNA 49/14 ─ ─ ─ ─ ─ 19.9 18 26 13 0.3 24 10 600 12 800 20 000
18 ─ ─ ─ TAF 182616 ─ ─ 25.5 18 26 16 0.3 24 13 400 17 500 20 000
─ ─ ─ TAF 182620 ─ ─ 32 18 26 20 0.3 24 17 000 23 600 20 000
─ ─ ─ TAF 192716 ─ ─ 27 19 27 16 0.3 25 14 000 18 700 20 000
19
─ ─ ─ TAF 192720 ─ ─ 34 19 27 20 0.3 25 17 700 25 300 20 000
RNA 4902 ─ ─ ─ ─ ─ 21.5 20 28 13 0.3 26 10 900 13 800 20 000
─ ─ ─ TAF 202816 ─ ─ 27.5 20 28 16 0.3 26 13 900 18 800 20 000
─ ─ ─ TAF 202820 ─ ─ 35.5 20 28 20 0.3 26 17 600 25 400 20 000
20 ─ RNA 6902 ─ ─ ─ ─ 37 20 28 23 0.3 26 19 300 28 800 20 000
─ ─ ─ ─ TR 203320 ─ 59.5 20 33 20 0.3 31 24 300 26 500 20 000
─ ─ ─ ─ ─ GTR 203320 69 20 33 20 0.3 31 29 200 37 200 7 500
─ ─ ─ TAF 212916 ─ ─ 29 21 29 16 0.3 27 14 400 20 000 19 000
21
─ ─ ─ TAF 212920 ─ ─ 36 21 29 20 0.3 27 18 200 27 100 19 000
RNA 4903 ─ ─ ─ ─ ─ 23.5 22 30 13 0.3 28 11 700 15 600 18 000
─ ─ ─ TAF 223016 ─ ─ 30 22 30 16 0.3 28 14 900 21 200 18 000
─ ─ ─ TAF 223020 ─ ─ 37.5 22 30 20 0.3 28 18 900 28 700 18 000
22 ─ RNA 6903 ─ ─ ─ ─ 40.5 22 30 23 0.3 28 20 800 32 500 18 000
─ ─ ─ ─ TR 223425 ─ 73.5 22 34 25 0.3 32 29 100 36 800 18 000
─ ─ ─ ─ ─ GTR 223425 87 22 34 25 0.3 32 37 900 57 800 7 000

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　TAF series with a roller set bore diameter Fw of 26 mm or less have no oil hole. In others, the outer ring has an oil groove and an
oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D9 1mm=0.03937inch
D10
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C C

r r

Fw

Fw
D

Da
D
r r
D
RNA49  TAF  TR GTR
RNA69（Fw ≦ 35）

Shaft dia. 24 − 30mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimension load rating load rating rotational
Da speed(2)
dia.
RNA 49 RNA 69 RNA 48 TAF TR GTR (1)
C C0
mm g Fw D C rs min Max.
mm N N min-1

─ ─ ─ TAF 243216 ─ ─   32 24 32 16 0.3 30 15 300 22 500 17 000

24
─ ─ ─ TAF 243220 ─ ─   40.5 24 32 20 0.3 30 19 400 30 500 17 000
─ ─ ─ TAF 253316 ─ ─   33.5 25 33 16 0.3 31 15 800 23 700 16 000
─ ─ ─ TAF 253320 ─ ─   42 25 33 20 0.3 31 20 000 32 100 16 000
RNA 4904 ─ ─ ─ ─ ─   55.5 25 37 17 0.3 35 21 000 25 000 16 000
─ RNA 6904 ─ ─ ─ ─   95.5 25 37 30 0.3 35 35 400 48 900 16 000
25
─ ─ ─ ─ TR 253820 ─   71 25 38 20 0.3 36 28 900 35 000 16 000
─ ─ ─ ─ TR 253825 ─   89 25 38 25 0.3 36 34 800 44 400 16 000
─ ─ ─ ─ ─ GTR 253820   81.5 25 38 20 0.3 36 33 300 46 500 6 000
─ ─ ─ ─ ─ GTR 253825 104 25 38 25 0.3 36 42 400 63 700 6 000
─ ─ ─ TAF 263416 ─ ─   34.5 26 34 16 0.3 32 16 300 24 900 15 000
26
─ ─ ─ TAF 263420 ─ ─   43.5 26 34 20 0.3 32 20 600 33 800 15 000
─ ─ ─ TAF 283720 ─ ─   51.5 28 37 20 0.3 35 21 700 37 100 14 000
─ ─ ─ TAF 283730 ─ ─   83.5 28 37 30 0.3 35 31 100 58 900 14 000
28
RNA 49/22 ─ ─ ─ ─ ─   56.5 28 39 17 0.3 37 21 400 28 900 14 000
─ RNA 69/22 ─ ─ ─ ─   97.5 28 39 30 0.3 37 36 300 56 900 14 000
─ ─ ─ TAF 293820 ─ ─   57 29 38 20 0.3 36 21 600 37 200 14 000
29
─ ─ ─ TAF 293830 ─ ─   85 29 38 30 0.3 36 30 900 59 100 14 000
─ ─ ─ TAF 304020 ─ ─   64.5 30 40 20 0.3 38 25 100 40 100 13 000
─ ─ ─ TAF 304030 ─ ─   97.5 30 40 30 0.3 38 36 000 63 900 13 000
RNA 4905 ─ ─ ─ ─ ─   64 30 42 17 0.3 40 23 700 30 700 13 000
30 ─ RNA 6905 ─ ─ ─ ─ 111 30 42 30 0.3 40 42 100 64 300 13 000
─ ─ ─ ─ TR 304425 ─ 115 30 44 25 0.3 42 37 900 52 100 13 000
─ ─ ─ ─ ─ GTR 304425 133 30 44 25 0.3 42 47 000 76 500 5 000

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　TAF series with a roller set bore diameter Fw of 26 mm or less have no oil hole. In others, the outer ring has an oil groove and an
oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D11 1mm=0.03937inch
D12
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C C C

r r r

Fw

Da
Fw
Fw

D
D
r r r
D
RNA49  TAF  TR RNA69 GTR
RNA69（Fw ≦ 35）

Shaft dia. 32 − 40mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimension load rating load rating rotational
speed(2)
dia.
RNA 49 RNA 69 RNA 48 TAF TR GTR (1)
Da C C0
mm g
Fw D C rs min Max.
mm N N min-1

─ ─ ─ TAF 324220 ─ ─   68 32 42 20 0.3 40 25 700 42 200 12 000

─ ─ ─ TAF 324230 ─ ─ 102 32 42 30 0.3 40 36 800 67 200 12 000
32 RNA 49/28 ─ ─ ─ ─ ─   76.5 32 45 17 0.3 43 24 500 32 700 12 000
─ RNA 69/28 ─ ─ ─ ─ 133 32 45 30 0.3 43 41 800 64 800 12 000
─ ─ ─ ─ ─ GTR 324530 152 32 45 30 0.3 43 58 000 101 000 4 500
─ ─ ─ TAF 354520 ─ ─   73.5 35 45 20 0.3 43 26 900 46 200 11 000
─ ─ ─ TAF 354530 ─ ─ 112 35 45 30 0.3 43 38 600 73 600 11 000
RNA 4906 ─ ─ ─ ─ ─   72.5 35 47 17 0.3 45 25 200 34 700 11 000
35 ─ RNA 6906 ─ ─ ─ ─ 125 35 47 30 0.3 45 43 000 69 000 11 000
─ ─ ─ ─ TR 354830 ─ 139 35 48 30 0.3 46 47 400 72 300  11 000
─ ─ ─ ─ ─ GTR 354830 163 35 48 30 0.3 46 61 100 110 000 4 500
─ ─ ─ TAF 374720 ─ ─   77.5 37 47 20 0.3 45 28 200 50 100 11 000
37
─ ─ ─ TAF 374730 ─ ─ 117 37 47 30 0.3 45 40 500 79 800 11 000
─ ─ ─ TAF 384820 ─ ─   79 38 48 20 0.3 46 28 100 50 200 11 000
─ ─ ─ TAF 384830 ─ ─ 119 38 48 30 0.3 46 40 300 80 000 11 000
38
─ ─ ─ ─ TR 385230 ─ 168 38 52 30 0.6 48 50 800 81 100 11 000
─ ─ ─ ─ ─ GTR 385230 195 38 52 30 0.6 48 64 200 121 000 4 000
─ ─ ─ TAF 405020 ─ ─   83 40 50 20 0.3 48 29 400 54 100 10 000
─ ─ ─ TAF 405030 ─ ─ 125 40 50 30 0.3 48 42 300 86 200 10 000
RNA 49/32 ─ ─ ─ ─ ─   96 40 52 20 0.6 48 31 200 47 800 10 000
40 ─ RNA 69/32 ─ ─ ─ ─ 172 40 52 36 0.6 48 53 500 95 700 10 000
─ ─ ─ ─ TR 405520 ─ 129 40 55 20 0.6 51 37 400 55 700 10 000
─ ─ ─ ─ ─ GTR 405520 144 40 55 20 0.6 51 44 300 73 600 3 500

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D13 1mm=0.03937inch
D14
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C C C

r r r

Fw

Da
Fw
Fw

D
D
r r r
D
RNA49  TAF  TR RNA69 GTR

Shaft dia. 42 − 50mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimension load rating load rating rotational
Da C speed(2)
dia.
RNA 49 RNA 69 RNA 48 TAF TR GTR (1)
C0
mm g
Fw D C rs min Max.
mm N N min-1

─ ─ ─ TAF 425220 ─ ─   86.5 42 52 20 0.3 50 29 900 56 200 9 500

─ ─ ─ TAF 425230 ─ ─ 130 42 52 30 0.3 50 43 000 89 400 9 500
RNA 4907 ─ ─ ─ ─ ─ 113 42 55 20 0.6 51 32 000 50 100 9 500
42 ─ RNA 6907 ─ ─ ─ ─ 200 42 55 36 0.6 51 54 900 100 000 9 500
─ ─ ─ ─ TR 425630 ─ 183 42 56 30 0.6 52 53 800 90 100 9 500
─ ─ ─ ─ ─ GTR 425630 210 42 56 30 0.6 52 67 500 133 000 3 500
─ ─ ─ TAF 435320 ─ ─   88.5 43 53 20 0.3 51 30 500 58 200 9 500
43
─ ─ ─ TAF 435330 ─ ─ 133 43 53 30 0.3 51 43 800 92 600 9 500
─ ─ ─ TAF 455520 ─ ─   92 45 55 20 0.3 53 31 000 60 200 9 000
─ ─ ─ TAF 455530 ─ ─ 138 45 55 30 0.3 53 44 600 95 800 9 000
45 RNA 49/38 ─ ─ ─ ─ ─ 120 45 58 20 0.6 54 33 600 54 600 9 000
─ ─ ─ ─ TR 455930 ─ 193 45 59 30 0.6 55 55 100 94 800 9 000
─ ─ ─ ─ ─ GTR 455930 225 45 59 30 0.6 55 70 300 142 000 3 500
─ ─ ─ TAF 475720 ─ ─   95 47 57 20 0.3 55 31 500 62 200 8 500
47
─ ─ ─ TAF 475730 ─ ─ 144 47 57 30 0.3 55 45 200 99 100 8 500
RNA 4908 ─ ─ ─ ─ ─ 152 48 62 22 0.6 58 41 600 67 400 8 500
─ ─ ─ ─ TR 486230 ─ 205 48 62 30 0.6 58 56 300 99 500 8 500
48
─ RNA 6908 ─ ─ ─ ─ 275 48 62 40 0.6 58 71 300 135 000 8 500
─ ─ ─ ─ ─ GTR 486230 240 48 62 30 0.6 58 72 700 154 000 3 000
─ ─ ─ TAF 506225 ─ ─ 159 50 62 25 0.3 60 43 000 85 300 8 000
─ ─ ─ TAF 506235 ─ ─ 225 50 62 35 0.3 60 58 000 125 000 8 000
50 ─ ─ ─ ─ TR 506430 ─ 210 50 64 30 0.6 60 57 700 104 000 8 000
RNA 49/42 ─ ─ ─ ─ ─ 174 50 65 22 0.6 61 42 500 70 300 8 000
─ ─ ─ ─ ─ GTR 506430 245 50 64 30 0.6 60 74 600 158 000 3 000

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D15 1mm=0.03937inch
D16
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C C C

r r r

Fw

Da
Fw
Fw

D
D
r r r
D
RNA49  TAF  TR RNA69 GTR

Shaft dia. 52 − 68mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimension load rating load rating rotational
dia. Da C C0 speed(2)
RNA 49 RNA 69 RNA 48 TAF TR GTR (1)
mm g
Fw D C rs min Max.
mm N N min-1

RNA 4909 ─ ─ ─ ─ ─ 197 52 68 22 0.6 64 43 500 73 300 7 500

52
　─ RNA 6909 ─ ─ ─ ─ 355 52 68 40 0.6 64 74 600 147 000 7 500
─ ─ ─ TAF 556825 ─ ─ 193 55 68 25 0.3 66 45 400 94 000 7 500
55 ─ ─ ─ TAF 556835 ─ ─ 255 55 68 35 0.3 66 61 200 138 000 7 500
RNA 49/48 ─ ─ ─ ─ ─ 188 55 70 22 0.6 66 44 300 76 300 7 500
RNA 4910 ─ ─ ─ ─ ─ 179 58 72 22 0.6 68 46 200 82 100 7 000
─ RNA 6910 ─ ─ ─ ─ 320 58 72 40 0.6 68 79 200 164 000 7 000
58
─ ─ ─ ─ TR 587745 ─ 515 58 77 45 1 72 104 000 191 000 7 000
─ ─ ─ ─ ─ GTR 587745 590 58 77 45 1 72 135 000 280 000 2 500
─ ─ ─ TAF 607225 ─ ─ 187 60 72 25 0.3 70 47 500 103 000 6 500
60 ─ ─ ─ TAF 607235 ─ ─ 260 60 72 35 0.3 70 64 100 151 000 6 500
RNA 49/52 ─ ─ ─ ─ ─ 205 60 75 22 0.6 71 47 100 85 100 6 500
─ ─ ─ ─ TR 628138 ─ 460 62 81 38 1 76 92 000 166 000 6 500
62
─ ─ ─ ─ ─ GTR 628138 520 62 81 38 1 76 118 000 241 000 2 500
RNA 4911 ─ ─ ─ ─ ─ 265 63 80 25 1 75 57 600 97 200 6 500
63 ─ RNA 6911 ─ ─ ─ ─ 475 63 80 45 1 75 98 700 194 000 6 500
─ ─ ─ TAF 657825 ─ ─ 225 65 78 25 0.6 74 49 600 112 000 6 000
65 ─ ─ ─ TAF 657835 ─ ─ 315 65 78 35 0.6 74 67 000 164 000 6 000
RNA 49/58 ─ ─ ─ ─ ─ 275 65 82 25 1 77 58 900 101 000 6 000
─ ─ ─ TAF 688225 ─ ─ 250 68 82 25 0.6 78 54 800 117 000 6 000
─ ─ ─ TAF 688235 ─ ─ 350 68 82 35 0.6 78 72 000 166 000 6 000
68
RNA 4912 ─ ─ ─ ─ ─ 285 68 85 25 1 80 60 200 105 000 6 000
─ RNA 6912 ─ ─ ─ ─ 510 68 85 45 1 80 103 000 211 000 6 000

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D17 1mm=0.03937inch
D18
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C C C

r r r

Fw

Da
Fw
Fw

D
D
r r r
D
RNA49  TAF  TR RNA69 GTR

Shaft dia. 70 − 85mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimension load rating load rating rotational
Da speed(2)
dia.
RNA 49 RNA 69 RNA 48 TAF TR GTR (1)
C C0
mm g Fw D C rs min Max.
mm N N min-1

─ ─ ─ TAF   708525 ─ ─ 280 70 85 25 0.6 81 55 500 120 000 5 500

─ ─ ─ TAF   708535 ─ ─ 395 70 85 35 0.6 81 73 000 171 000 5 500
70 RNA 49/62 ─ ─ ─ ─ ─ 320 70 88 25 1 83 61 500 109 000 5 500
─ ─ ─ ─ TR   708945 ─ 605 70 89 45 1 84 114 000 228 000 5 500
─ ─ ─ ─ ─ GTR   708945 690 70 89 45 1 84 147 000 336 000 2 000
RNA 4913 ─ ─ ─ ─ ─ 325 72 90 25 1 85 62 700 113 000 5 500
72 ─ RNA 6913 ─ ─ ─ ─ 585 72 90 45 1 85 108 000 227 000 5 500
─ ─ ─ TAF   739025 ─ ─ 335 73 90 25 1 85 61 100 127 000 5 500
73
─ ─ ─ TAF   739035 ─ ─ 475 73 90 35 1 85 80 400 181 000 5 500
─ ─ ─ TAF   759225 ─ ─ 345 75 92 25 1 87 62 100 131 000 5 500
75 ─ ─ ─ TAF   759235 ─ ─ 485 75 92 35 1 87 81 700 186 000 5 500
RNA 49/68 ─ ─ ─ ─ ─ 470 75 95 30 1 90 79 900 147 000 5 500
─ ─ ─ TAF   809525 ─ ─ 315 80 95 25 1 90 59 400 137 000 5 000
─ ─ ─ TAF   809535 ─ ─ 445 80 95 35 1 90 78 100 195 000 5 000
80
RNA 4914 ─ ─ ─ ─ ─ 495 80 100 30 1 95 83 200 158 000 5 000
─ RNA 6914 ─ ─ ─ ─ 910 80 100 54 1 95 134 000 311 000 5 000
─ ─ ─ ─ TR 8310845 ─ 995 83 108 45 1 103 146 000 270 000 5 000
83
─ ─ ─ ─ ─ GTR 8310845 1 090 83 108 45 1 103 190 000 396 000 1 800
─ ─ ─ TAF 8510525 ─ ─ 435 85 105 25 1 100 76 300 145 000 4 500
RNA 4915 ─ ─ ─ ─ ─ 525 85 105 30 1 100 86 200 169 000 4 500
85
─ ─ ─ TAF 8510535 ─ ─ 610 85 105 35 1 100 102 000 210 000 4 500
─ RNA 6915 ─ ─ ─ ─ 960 85 105 54 1 100 138 000 331 000 4 500

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D19 1mm=0.03937inch
D20
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C C C

r r r

Fw

Da
Fw
Fw

D
D
r r r
D
RNA49  TAF  TR RNA69 GTR

Shaft dia. 90 − 105mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimension load rating load rating rotational
Da speed(2)
dia.
RNA 49 RNA 69 RNA 48 TAF TR GTR (1)
C C0
mm g Fw D C rs min Max.
mm N N min-1

─ ─ ─ TAF   9011025 ─ ─ 455 90 110 25 1 105 77 300 150 000 4 500

RNA 4916 ─ ─ ─ ─ ─ 550 90 110 30 1 105 87 300 175 000 4 500
90
─ ─ ─ TAF   9011035 ─ ─ 640 90 110 35 1 105 103 000 217 000 4 500
─ RNA 6916 ─ ─ ─ ─ 1 010 90 110 54 1 105 143 000 351 000 4 500
─ ─ ─ ─ TR   9311850 ─ 1 210 93 118 50 1 113 165 000 329 000 4 500
93
─ ─ ─ ─ ─ GTR   9311850 1 340 93 118 50 1 113 224 000 509 000 1 600
─ ─ ─ TAF   9511526 ─ ─ 495 95 115 26 1 110 79 700 159 000 4 000
RNA 49/82 ─ ─ ─ ─ ─ 575 95 115 30 1 110 90 000 186 000 4 000
95 ─ ─ ─ TAF   9511536 ─ ─ 690 95 115 36 1 110 106 000 231 000 4 000
─ ─ ─ ─ TR   9512045 ─ 1 120 95 120 45 1.5 112 155 000 305 000 4 000
─ ─ ─ ─ ─ GTR   9512045 1 230 95 120 45 1.5 112 204 000 455 000 1 600
─ ─ ─ TAF 10012026 ─ ─ 525 100 120 26 1 115 82 400 168 000 4 000
RNA 4917 ─ ─ ─ ─ ─ 705 100 120 35 1.1 113.5 110 000 244 000 4 000
─ ─ ─ TAF 10012036 ─ ─ 725 100 120 36 1 115 110 000 244 000 4 000
100 ─ RNA 6917 ─ ─ ─ ─ 1 300 100 120 63 1.1 113.5 173 000 467 000 4 000
─ ─ ─ ─ TR 10012550 ─ 1 290 100 125 50 1.5 117 172 000 355 000 4 000
─ ─ ─ ─ ─ GTR 10012550 1 440 100 125 50 1.5 117 234 000 549 000 1 500
─ ─ ─ TAF 10512526 ─ ─ 545 105 125 26 1 120 84 700 178 000 4 000
RNA 4918 ─ ─ ─ ─ ─ 740 105 125 35 1.1 118.5 113 000 258 000 4 000
105
─ ─ ─ TAF 10512536 ─ ─ 760  105 125 36 1 120 113 000 258 000 4 000
─ RNA 6918 ─ ─ ─ ─ 1 360 105 125 63 1.1 118.5 178 000 490 000 4 000

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D21 1mm=0.03937inch
D22
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C C C

r r r

Fw

Da
Fw
Fw

D
D
r r r
D
RNA49  RNA48 RNA69 GTR
TAF  TR

Shaft dia. 110 − 170mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimension load rating load rating rotational
Da speed(2)
dia.
RNA 49 RNA 69 RNA 48 TAF TR GTR (1)
C C0
mm g
Fw D C rs min Max.
mm N N min-1

─ ─ ─ TAF 11013030 ─ ─ 660 110 130 30 1 125 106 000 240 000 3 500
RNA 4919 ─ ─ ─ ─ ─ 770 110 130 35 1.1 123.5 116 000 271 000 3 500
─ ─ ─ TAF 11013040 ─ ─ 880 110 130 40 1 125 134 000 324 000 3 500
110 ─ RNA 6919 ─ ─ ─ ─ 1 420 110 130 63 1.1 123.5 182 000 514 000 3 500
─ ─ ─ ─ TR 11013550 ─ 1 400 110 135 50 1.5 127 183 000 395 000 3 500
─ ─ ─ ─ ─ GTR 11013550 1 560 110 135 50 1.5 127 245 000 603 000 1 400
RNA 4920 ─ ─ ─ ─ ─ 1 190 115 140 40 1.1 133.5 145 000 329 000 3 500
115 ─ ─ ─ ─ TR 11515350 ─ 2 350 115 153 50 1.5 145 233 000 414 000 3 500
─ ─ ─ ─ ─ GTR 11515350 2 600 115 153 50 1.5 145 315 000 614 000 1 300
120 ─ ─ RNA 4822 ─ ─ ─ 790 120 140 30 1 135 93 200 239 000 3 500
125 RNA 4922 ─ ─ ─ ─ ─ 1 280 125 150 40 1.1 143.5 152 000 357 000 3 000
130 ─ ─ RNA 4824 ─ ─ ─ 850 130 150 30 1 145 96 900 259 000 3 000
135 RNA 4924 ─ ─ ─ ─ ─ 1 930 135 165 45 1.1 158.5 187 000 435 000 3 000
─ ─ ─ ─ TR 14017860 ─ 3 320 140 178 60 1.5 170 307 000 625 000 3 000
140
─ ─ ─ ─ ─ GTR 14017860 3 730 140 178 60 1.5 170 409 000 923 000 1 100
145 ─ ─ RNA 4826 ─ ─ ─ 1 100 145 165 35 1.1 158.5 116 000 340 000 3 000
RNA 4926 ─ ─ ─ ─ ─ 2 360 150 180 50 1.5 172 215 000 540 000 2 500
150 ─ ─ ─ ─ TR 15018860 ─ 3 540 150 188 60 1.5 180 320 000 675 000 2 500
─ ─ ─ ─ ─ GTR 15018860 3 970 150 188 60 1.5 180 423 000 989 000 1 000
155 ─ ─ RNA 4828 ─ ─ ─ 1 170 155 175 35 1.1 168.5 120 000 363 000 2 500
160 RNA 4928 ─ ─ ─ ─ ─ 2 500 160 190 50 1.5 182 224 000 580 000 2 500
165 ─ ─ RNA 4830 ─ ─ ─ 1 750 165 190 40 1.1 183.5 168 000 446 000 2 500
170 RNA 4930 ─ ─ ─ ─ ─ 4 090 170 210 60 2 201 324 000 712 000 2 500

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D23 1mm=0.03937inch
D24
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C

Fw
D

Da
r
D
RNA49  RNA48

Shaft dia. 175 − 350mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimension load rating load rating rotational
Da speed(2)
dia.
RNA 49 RNA 69 RNA 48 TAF TR GTR (1)
C C0
mm g Fw D C rs min Max.
mm N N min-1

175 ─ ─ RNA 4832 ─ ─ ─ 1 850 175 200 40 1.1 193.5 173 000 474 000 2 500
180 RNA 4932 ─ ─ ─ ─ ─ 4 310 180 220 60 2 211 337 000 761 000 1 900
185 ─ ─ RNA 4834 ─ ─ ─ 2 700 185 215 45 1.1 208.5 211 000 567 000 1 900
190 RNA 4934 ─ ─ ─ ─ ─ 4 530 190 230 60 2 221 347 000 810 000 1 900
195 ─ ─ RNA 4836 ─ ─ ─ 2 840 195 225 45 1.1 218.5 218 000 602 000 1 900
205 RNA 4936 ─ ─ ─ ─ ─ 6 250 205 250 69 2 241 434 000 989 000 1 900
210 ─ ─ RNA 4838 ─ ─ ─ 3 380 210 240 50 1.5 232 249 000 726 000 1 800
215 RNA 4938 ─ ─ ─ ─ ─ 6 500 215 260 69 2 251 440 000 1 020 000 1 700
220 ─ ─ RNA 4840 ─ ─ ─ 3 520 220 250 50 1.5 242 255 000 766 000 1 600
225 RNA 4940 ─ ─ ─ ─ ─ 10 400 225 280 80 2.1 269 518 000 1 120 000 1 600
240 ─ ─ RNA 4844 ─ ─ ─ 3 820 240 270 50 1.5 262 266 000 833 000 1 500
245 RNA 4944 ─ ─ ─ ─ ─ 11 200 245 300 80 2.1 289 536 000 1 200 000 1 400
─ ─ RNA 4848 ─ ─ ─ 5 670 265 300 60 2 291 345 000 1 150 000 1 300
265
RNA 4948 ─ ─ ─ ─ ─ 12 000 265 320 80 2.1 309 565 000 1 320 000 1 300
285 ─ ─ RNA 4852 ─ ─ ─ 6 070 285 320 60 2 311 354 000 1 220 000 1 100
290 RNA 4952 ─ ─ ─ ─ ─ 21 200 290 360 100 2.1 349 847 000 1 900 000 1 100
305 ─ ─ RNA 4856 ─ ─ ─ 9 750 305 350 69 2 341 486 000 1 550 000 950
310 RNA 4956 ─ ─ ─ ─ ─ 22 500 310 380 100 2.1 369 877 000 2 040 000 950
330 ─ ─ RNA 4860 ─ ─ ─ 13 200 330 380 80 2.1 369 610 000 1 900 000 900
340 RNA 4960 ─ ─ ─ ─ ─ 33 400 340 420 118 3 407 1 130 000 2 650 000 850
350 ─ ─ RNA 4864 ─ ─ ─ 14 100 350 400 80 2.1 389 635 000 2 040 000 750
Notes(1)　　Minimum allowable value of chamfer dimension r
 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D25 1mm=0.03937inch
D26
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C

Fw
D

Da
r
D
RNA49  RNA48

Shaft dia. 360 − 490mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimension load rating load rating rotational
Da speed(2)
dia.
RNA 49 RNA 69 RNA 48 TAF TR GTR (1)
C C0
mm g
Fw D C rs min Max.
mm N N min-1

360 RNA 4964 ─ ─ ─ ─ ─ 35 200 360 440 118 3 427 1 170 000 2 830 000 750
370 ─ ─ RNA 4868 ─ ─ ─ 14 800 370 420 80 2.1 409 651 000 2 140 000 700
380 RNA 4968 ─ ─ ─ ─ ─ 37 000 380 460 118 3 447 1 220 000 3 020 000 700
390 ─ ─ RNA 4872 ─ ─ ─ 15 600 390 440 80 2.1 429 680 000 2 320 000 650
400 RNA 4972 ─ ─ ─ ─ ─ 38 700 400 480 118 3 467 1 260 000 3 200 000 600
415 ─ ─ RNA 4876 ─ ─ ─ 27 900 415 480 100 2.1 469 951 000 2 860 000 600
430 RNA 4976 ─ ─ ─ ─ ─ 56 400 430 520 140 4 504 1 540 000 4 030 000 500
450 RNA 4980 ─ ─ ─ ─ ─ 58 800 450 540 140 4 524 1 590 000 4 270 000 500
470 RNA 4984 ─ ─ ─ ─ ─ 61 200 470 560 140 4 544 1 640 000 4 510 000 500
490 RNA 4988 ─ ─ ─ ─ ─ 86 900 490 600 160 4 584 1 910 000 5 140 000 400

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D27 1mm=0.03937inch
D28
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Inner Ring
C

r
S

Fw
D

Da
da
d
r

r D
　 NA49  TAFI
　 NA69（d ≦ 30）

Shaft dia. 5 − 12mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) dimensions　mm load rating load rating rotational
speed(3)
dia.
NA 49 NA 69 NA 48 TAFI TRI GTRI (1) (2) da Da C C0
mm g d D C B rs min Fw S Min. Max. Max.
N N min-1

NA   495 ─ ─ ─ ─ ─ 7.3 5 13 10 ─ 0.15 7 0.5   6.2   6.7 11.8 2 960 2 690 60 000 LRT  5710
5 ─ ─ ─ TAFI 51512 ─ ─ 11.9 5 15 12 ─ 0.2 8 0.5   6.6   7.7 13.4 5 060 4 690 50 000 LRT  5812
─ ─ ─ TAFI 51516 ─ ─ 16.7 5 15 16 ─ 0.2 8 0.5   6.6   7.7 13.4 7 080 7 220 50 000 LRT  5816
NA   496 ─ ─ ─ ─ ─ 9.1 6 15 10 ─ 0.15 8 0.5   7.2   7.7 13.8 3 960 3 420 50 000 LRT  6810
6 ─ ─ ─ TAFI 61612 ─ ─ 13 6 16 12 ─ 0.2 9 0.5   7.6   8.7 14.4 5 490 5 330 45 000 LRT  6912
─ ─ ─ TAFI 61616 ─ ─ 17.5 6 16 16 ─ 0.2 9 0.5   7.6   8.7 14.4 7 680 8 210 45 000 LRT  6916
NA   497 ─ ─ ─ ─ ─ 11.2 7 17 10 ─ 0.15 9 0.5   8.2   8.7 15.8 4 530 3 650 45 000 LRT  7910
7 ─ ─ ─ TAFI 71712 ─ ─ 14.3 7 17 12 ─ 0.2 10 0.5   8.6   9.7 15.4 5 880 5 970 40 000 LRT  71012
─ ─ ─ TAFI 71716 ─ ─ 19.2 7 17 16 ─ 0.2 10 0.5   8.6   9.7 15.4 8 230 9 190 40 000 LRT  71016
8 NA   498 ─ ─ ─ ─ ─ 15 8 19 11 ─ 0.2 10 0.5   9.6   9.9 17.4 6 180 5 030 40 000 LRT  81011
─ ─ ─ TAFI   91912 ─ ─ 16.7 9 19 12 ─ 0.3 12 0.5 11 11.5 17 6 610 7 260 35 000 LRT  91212
9 ─ ─ ─ TAFI   91916 ─ ─ 22.5 9 19 16 ─ 0.3 12 0.5 11 11.5 17 9 250 11 200 35 000 LRT  91216
NA   499 ─ ─ ─ ─ ─ 16.7 9 20 11 ─ 0.3 12 0.5 11 11.5 18 6 600 6 310 35 000 LRT  91211
NA 4900 ─ ─ ─ ─ ─ 24 10 22 13 ─ 0.3 14 0.5 12 13 20 9 230 10 100 30 000 LRT 101413
10 ─ ─ ─ TAFI 102216 ─ ─ 30 10 22 16 ─ 0.3 14 0.5 12 13 20 11 700 13 700 30 000 LRT 101416
─ ─ ─ TAFI 102220 ─ ─ 38 10 22 20 ─ 0.3 14 0.5 12 13 20 14 800 18 600 30 000 LRT 101420
NA 4901 ─ ─ ─ ─ ─ 26.5 12 24 13 ─ 0.3 16 0.5 14 15 22 9 660 11 100 25 000 LRT 121613
─ ─ ─ TAFI 122416 ─ ─ 33.5 12 24 16 ─ 0.3 16 0.5 14 15 22 12 300 15 100 25 000 LRT 121616
12
─ ─ ─ TAFI 122420 ─ ─ 42.5 12 24 20 ─ 0.3 16 0.5 14 15 22 15 500 20 400 25 000 LRT 121620
─ NA 6901 ─ ─ ─ ─ 44.5 12 24 22 ─ 0.3 16 0.5 14 15 22 17 100 23 000 25 000 LRT 121622

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable axial shift amount of inner ring to outer ring
 　　 (3)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　TAFI series with a bore diameter d of 22 mm or less have no oil hole. In others, the outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D29 1mm=0.03937inch
D30
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Inner Ring
B B
C C C

r r
r
r r
r
S

Fw
Fw
D

D
Fw

d
d

Da
D

da
d
r r r

r r r D
　 NA49  TAFI TRI GTRI
　 NA69（d ≦ 30）

Shaft dia. 15 − 22mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) dimensions　mm load rating load rating rotational
speed(3)
dia.
NA 49 NA 69 NA 48 TAFI TRI GTRI (1) (2) da Da C C0
mm g d D C B rs min Fw S Min. Max. Max.
N N min-1

─ ─ ─ TAFI 152716 ─ ─   39.5 15 27 16 ─ 0.3 19 0.5 17 18 25 14 000 18 700 20 000 LRT   151916
─ ─ ─ TAFI 152720 ─ ─   50 15 27 20 ─ 0.3 19 0.5 17 18 25 17 700 25 300 20 000 LRT   151920
NA 4902 ─ ─ ─ ─ ─   35   15 28 13 ─ 0.3 20 0.3 17 19 26 10 900 13 800 20 000 LRT   152013
15 ─ NA 6902 ─ ─ ─ ─   61 15 28 23 ─ 0.3 20 0.3 17 19 26 19 300 28 800 20 000 LRT 152023
─ ─ ─ ─ TRI 153320 ─   81 15 33 20 20.5 0.3 20 0.3 17 19 31 24 300 26 500 20 000 LRT   152020
─ ─ ─ ─ ─ GTRI 153320   90.5 15 33 20 20.5 0.3 20 ─ 17 19 31 29 200 37 200 7 500 LRTZ 152020
─ ─ ─ TAFI 172916 ─ ─   43.5 17 29 16 ─ 0.3 21 0.5 19 20 27 14 400 20 000 19 000 LRT   172116
─ ─ ─ TAFI 172920 ─ ─   54 17 29 20 ─ 0.3 21 0.5 19 20 27 18 200 27 100 19 000 LRT   172120
NA 4903 ─ ─ ─ ─ ─   39 17 30 13 ─ 0.3 22 0.3 19 21 28 11 700 15 600 18 000 LRT   172213
17 ─ NA 6903 ─ ─ ─ ─   67 17 30 23 ─ 0.3 22 0.3 19 21 28 20 800 32 500 18 000 LRT   172223
─ ─ ─ ─ TRI 173425 ─ 104 17 34 25 25.5 0.3 22 0.5 19 21 32 29 100 36 800 18 000 LRT   172225
─ ─ ─ ─ ─ GTRI 173425 117 17 34 25 25.5 0.3 22 ─ 19 21 32 37 900 57 800 7 000 LRTZ 172225
─ ─ ─ TAFI 203216 ─ ─   48.5 20 32 16 ─ 0.3 24 0.5 22 23 30 15 300 22 500 17 000 LRT   202416
─ ─ ─ TAFI 203220 ─ ─   61 20 32 20 ─ 0.3 24 0.5 22 23 30 19 400 30 500 17 000 LRT   202420
NA 4904 ─ ─ ─ ─ ─   78.5 20 37 17 ─ 0.3 25 0.5 22 24 35 21 000 25 000 16 000 LRT   202517
─ NA 6904 ─ ─ ─ ─ 136 20 37 30 ─ 0.3 25 0.5 22 24 35 35 400 48 900 16 000 LRT   202530
20
─ ─ ─ ─ TRI 203820 ─   99 20 38 20 20.5 0.3 25 0.3 22 24 36 28 900 35 000 16 000 LRT   202520
─ ─ ─ ─ TRI 203825 ─ 124 20 38 25 25.5 0.3 25 0.5 22 24 36 34 800 44 400 16 000 LRT   202525
─ ─ ─ ─ ─ GTRI 203820 110 20 38 20 20.5 0.3 25 ─ 22 24 36 33 300 46 500 6 000 LRTZ 202520
─ ─ ─ ─ ─ GTRI 203825 138 20 38 25 25.5 0.3 25 ─ 22 24 36 42 400 63 700 6 000 LRTZ 202525
─ ─ ─ TAFI 223416 ─ ─   52 22 34 16 ─ 0.3 26 0.5 24 25 32 16 300 24 900 15 000 LRT   222616
─ ─ ─ TAFI 223420 ─ ─   67.5 22 34 20 ─ 0.3 26 0.5 24 25 32 20 600 33 800 15 000 LRT   222620
22
NA 49/22 ─ ─ ─ ─ ─   87 22 39 17 ─ 0.3 28 1 24 27 37 21 400 28 900 14 000 LRT 222817
─ NA 69/22 ─ ─ ─ ─ 152 22 39 30 ─ 0.3 28 0.5 24 27 37 36 300 56 900 14 000 LRT 222830

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable axial shift amount of inner ring to outer ring
 　　 (3)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　TAFI series with a bore diameter d of 22 mm or less have no oil hole. In others, the outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D31 1mm=0.03937inch
D32
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Inner Ring
B B
C C C C

r r r
r

r r r
r
S

Fw
Fw
Fw

D
Fw

d
d

Da
D

da
d
d
r r r r

r r r r D
　 NA49  TAFI NA69 TRI GTRI
　 NA69（d ≦ 30）

Shaft dia. 25 − 32mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) dimensions　mm load rating load rating rotational
speed(3)
dia.
NA 49 NA 69 NA 48 TAFI TRI GTRI (1) (2) da Da C C0
mm g d D C B rs min Fw S Min. Max. Max.
N N min-1

─ ─ ─ TAFI 253820 ─ ─ 82 25 38 20 ─ 0.3 29 0.5 27 28 36 21 600 37 200 14 000 LRT   252920

─ ─ ─ TAFI 253830 ─ ─ 123 25 38 30 ─ 0.3 29 1 27 28 36 30 900 59 100 14 000 LRT   252930
NA 4905 ─ ─ ─ ─ ─   92.5 25 42 17 ─ 0.3 30 0.5 27 29 40 23 700 30 700 13 000 LRT   253017
25 ─ NA 6905 ─ ─ ─ ─ 160 25 42 30 ─ 0.3 30 0.5 27 29 40 42 100 64 300 13 000 LRT   253030
─ ─ ─ ─ TRI 254425 ─ 157 25 44 25 25.5 0.3 30 0.5 27 29 42 37 900 52 100 13 000 LRT   253025
─ ─ ─ ─ ─ GTRI 254425 175 25 44 25 25.5 0.3 30 ─ 27 29 42 47 000 76 500 5 000 LRTZ 253025
─ ─ ─ TAFI 284220 ─ ─   96.5 28 42 20 ─ 0.3 32 0.5 30 31 40 25 700 42 200 12 000 LRT   283220
─ ─ ─ TAFI 284230 ─ ─ 145 28 42 30 ─ 0.3 32 1 30 31 40 36 800 67 200 12 000 LRT   283230
28 NA 49/28 ─ ─ ─ ─ ─ 101 28 45 17 ─ 0.3 32 1 30 31 43 24 500 32 700 12 000 LRT   283217
─ NA 69/28 ─ ─ ─ ─ 176 28 45 30 ─ 0.3 32 1 30 31 43 41 800 64 800 12 000 LRT   283230
─ ─ ─ ─ ─ GTRI 284530 196 28 45 30 30.5 0.3 32 ─ 30 31 43 58 000 101 000 4 500 LRTZ 283230
─ ─ ─ TAFI 304520 ─ ─ 112 30 45 20 ─ 0.3 35 0.3 32 34 43 26 900 46 200 11 000 LRT   303520
─ ─ ─ TAFI 304530 ─ ─ 171 30 45 30 ─ 0.3 35 0.5 32 34 43 38 600 73 600 11 000 LRT   303530
NA 4906 ─ ─ ─ ─ ─ 106 30 47 17 ─ 0.3 35 0.5 32 34 45 25 200 34 700 11 000 LRT   303517
30 ─ NA 6906 ─ ─ ─ ─ 184 30 47 30 ─ 0.3 35 0.5 32 34 45 43 000 69 000 11 000 LRT   303530
─ ─ ─ ─ TRI 304830 ─ 199 30 48 30 30.5 0.3 35 1 32 34 46 47 400 72 300 11 000 LRT   303530-1
─ ─ ─ ─ ─ GTRI 304830 225 30 48 30 30.5 0.3 35 ─ 32 34 46 61 100 110 000 4 500 LRTZ 303530
─ ─ ─ TAFI 324720 ─ ─ 121 32 47 20 ─ 0.3 37 0.3 34 36 45 28 200 50 100 11 000 LRT   323720
─ ─ ─ TAFI 324730 ─ ─ 180 32 47 30 ─ 0.3 37 0.5 34 36 45 40 500 79 800 11 000 LRT   323730
NA 49/32 ─ ─ ─ ─ ─ 165 32 52 20 ─ 0.6 40 0.5 36 39 48 31 200 47 800 10 000 LRT   324020
32
─ ─ ─ ─ TRI 325230 ─ 245 32 52 30 30.5 0.6 38 0.5 36 37 48 50 800 81 100 11 000 LRT   323830
─ NA 69/32 ─ ─ ─ ─ 295 32 52 36 ─ 0.6 40 0.3 36 39 48 53 500 95 700 10 000 LRT   324036
─ ─ ─ ─ ─ GTRI 325230 270 32 52 30 30.5 0.6 38 ─ 36 37 48 64 200 121 000 4 000 LRTZ 323830

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable axial shift amount of inner ring to outer ring
 　　 (3)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D33 1mm=0.03937inch
D34
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Inner Ring
C B B
C
C C
r r r r

r r r r
S

Fw
Fw

D
D

d
d

Fw
Fw
D

D
d
d

Da
da
r r
r r
r r
r r D
　 NA49  TAFI NA69 TRI GTRI

Shaft dia. 35 − 45mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) dimensions　mm load rating load rating rotational
speed(3)
dia.
NA 49 NA 69 NA 48 TAFI TRI GTRI (1) (2) da Da C C0
mm g d D C B rs min Fw S Min. Max. Max.
N N min-1

─ ─ ─ TAFI 355020 ─ ─ 129 35 50 20 ─ 0.3 40 0.3 37 39 48 29 400 54 100 10 000 LRT   354020

─ ─ ─ TAFI 355030 ─ ─ 192 35 50 30 ─ 0.3 40 0.5 37 39 48 42 300 86 200 10 000 LRT   354030
NA 4907 ─ ─ ─ ─ ─ 178 35 55 20 ─ 0.6 42 0.5 39 41 51 32 000 50 100 9 500 LRT   354220
35 ─ NA 6907 ─ ─ ─ ─ 320 35 55 36 ─ 0.6 42 0.3 39 41 51 54 900 100 000 9 500 LRT   354236
─ ─ ─ ─ TRI 355630 ─ 280 35 56 30 30.5 0.6 42 0.5 39 41 52 53 800 90 100 9 500 LRT   354230
─ ─ ─ ─ ─ GTRI 355520 191 35 55 20 20.5 0.6 40 ─ 39 39.5 51 44 300 73 600 3 500 LRTZ 354020
─ ─ ─ ─ ─ GTRI 355630 310 35 56 30 30.5 0.6 42 ─ 39 41 52 67 500 133 000 3 500 LRTZ 354230
─ ─ ─ TAFI 385320 ─ ─ 136 38 53 20 ─ 0.3 43 0.3 40 42 51 30 500 58 200 9 500 LRT   384320
38
─ ─ ─ TAFI 385330 ─ ─ 205 38 53 30 ─ 0.3 43 0.5 40 42 51 43 800 92 600 9 500 LRT   384330
─ ─ ─ TAFI 405520 ─ ─ 143 40 55 20 ─ 0.3 45 0.3 42 44 53 31 000 60 200 9 000 LRT   404520
─ ─ ─ TAFI 405530 ─ ─ 215 40 55 30 ─ 0.3 45 0.5 42 44 53 44 600 95 800 9 000 LRT   404530

40 ─ ─ ─ ─ TRI 405930 ─ 270 40 59 30 30.5 0.6 45 1 44 44.5 55 55 100 94 800 9 000 LRT   404530-1
NA 4908 ─ ─ ─ ─ ─ 245 40 62 22 ─ 0.6 48 0.5 44 47 58 41 600 67 400 8 500 LRT   404822
─ NA 6908 ─ ─ ─ ─ 440 40 62 40 ─ 0.6 48 0.3 44 47 58 71 300 135 000 8 500 LRT   404840
─ ─ ─ ─ ─ GTRI 405930 300 40 59 30 30.5 0.6 45 ─ 44 44.5 55 70 300 142 000 3 500 LRTZ 404530
─ ─ ─ TAFI 425720 ─ ─ 149 42 57 20 ─ 0.3 47 0.3 44 46 55 31 500 62 200 8 500 LRT   424720
─ ─ ─ TAFI 425730 ─ ─ 225 42 57 30 ─ 0.3 47 0.5 44 46 55 45 200 99 100 8 500 LRT   424730
42
─ ─ ─ ─ TRI 426230 ─ 305 42 62 30 30.5 0.6 48 0.5 46 47 58 56 300 99 500 8 500 LRT   424830
─ ─ ─ ─ ─ GTRI 426230 340 42 62 30 30.5 0.6 48 ─ 46 47 58 72 700 154 000 3 000 LRTZ 424830
─ ─ ─ TAFI 456225 ─ ─ 230 45 62 25 ─ 0.3 50 0.5 47 49 60 43 000 85 300 8 000 LRT   455025
─ ─ ─ TAFI 456235 ─ ─ 320 45 62 35 ─ 0.3 50 1 47 49 60 58 000 125 000 8 000 LRT   455035

45 ─ ─ ─ ─ TRI 456430 ─ 300 45 64 30 30.5 0.6 50 1 49 49.5 60 57 700 104 000 8 000 LRT   455030
NA 4909 ─ ─ ─ ─ ─ 285 45 68 22 ─ 0.6 52 0.5 49 51 64 43 500 73 300 7 500 LRT   455222
─ NA 6909 ─ ─ ─ ─ 520 45 68 40 ─ 0.6 52 0.3 49 51 64 74 600 147 000 7 500 LRT   455240
─ ─ ─ ─ ─ GTRI 456430 335 45 64 30 30.5 0.6 50 ─ 49 49.5 60 74 600 158 000 3 000 LRTZ 455030

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable axial shift amount of inner ring to outer ring
 　　 (3)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D35 1mm=0.03937inch
D36
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Inner Ring
B B
C C C C

r r
r r

r r r
r S

Fw

Fw
D

Da
Fw

da
D
Fw

d
D
D

d
d
r r r r

r r r r D
　 NA49  TAFI NA69 TRI GTRI

Shaft dia. 50 − 70mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) dimensions　mm load rating load rating rotational
speed(3)
dia.
NA 49 NA 69 NA 48 TAFI TRI GTRI (1) (2) da Da C C0
mm g d D C B rs min Fw S Min. Max. Max.
N N min-1

─ ─ ─ TAFI 506825 ─ ─ 270 50 68 25 ─ 0.3 55 0.5 52 54 66 45 400 94 000 7 500 LRT   505525

─ ─ ─ TAFI 506835 ─ ─ 365 50 68 35 ─ 0.3 55 1 52 54 66 61 200 138 000 7 500 LRT   505535
NA 4910 ─ ─ ─ ─ ─ 295 50 72 22 ─ 0.6 58 0.5 54 57 68 46 200 82 100 7 000 LRT   505822
50 ─ NA 6910 ─ ─ ─ ─ 530 50 72 40 ─ 0.6 58 0.3 54 57 68 79 200 164 000 7 000 LRT   505840
─ ─ ─ ─ TRI 507745 ─ 755 50 77 45 45.5 1 58 2 55 57 72 104 000 191 000 7 000 LRT   505845
─ ─ ─ ─ ─ GTRI 507745 825 50 77 45 45.5 1 58 ─ 55 57 72 135 000 280 000 2 500 LRTZ 505845
─ ─ ─ TAFI 557225 ─ ─ 275 55 72 25 ─ 0.3 60 0.5 57 59 70 47 500 103 000 6 500 LRT   556025
─ ─ ─ TAFI 557235 ─ ─ 380 55 72 35 ─ 0.3 60 1 57 59 70 64 100 151 000 6 500 LRT   556035
NA 4911 ─ ─ ─ ─ ─ 410 55 80 25 ─ 1 63 1 60 61 75 57 600 97 200 6 500 LRT   556325
55 ─ NA 6911 ─ ─ ─ ─ 730 55 80 45 ─ 1 63 0.5 60 61 75 98 700 194 000 6 500 LRT   556345
─ ─ ─ ─ TRI 558138 ─ 650 55 81 38 38.5 1 62 1.5 60 60.5 76 92 000 166 000 6 500 LRT   556238
─ ─ ─ ─ ─ GTRI 558138 710 55 81 38 38.5 1 62 ─ 60 60.5 76 118 000 241 000 2 500 LRTZ 556238
─ ─ ─ TAFI 608225 ─ ─ 395 60 82 25 ─ 0.6 68 0.3 64 66 78 54 800 117 000 6 000 LRT   606825
─ ─ ─ TAFI 608235 ─ ─ 560 60 82 35 ─ 0.6 68 1 64 66 78 72 000 166 000 6 000 LRT   606835
NA 4912 ─ ─ ─ ─ ─ 440 60 85 25 ─ 1 68 1 65 66 80 60 200 105 000 6 000 LRT   606825-1
60 ─ NA 6912 ─ ─ ─ ─ 785 60 85 45 ─ 1 68 0.5 65 66 80 103 000 211 000 6 000 LRT   606845
─ ─ ─ ─ TRI 608945 ─ 960 60 89 45 45.5 1 70 2 65 68 84 114 000 228 000 5 500 LRT   607045
─ ─ ─ ─ ─ GTRI 608945 1 050 60 89 45 45.5 1 70 ─ 65 68 84 147 000 336 000 2 000 LRTZ 607045
NA 4913 ─ ─ ─ ─ ─ 470 65 90 25 ─ 1 72 1 70 70.5 85 62 700 113 000 5 500 LRT   657225
65 ─ ─ ─ TAFI 659035 ─ ─ 710 65 90 35 ─ 1 73 1 70 71 85 80 400 181 000 5 500 LRT   657335
─ NA 6913 ─ ─ ─ ─ 840 65 90 45 ─ 1 72 0.5 70 70.5 85 108 000 227 000 5 500 LRT   657245
─ ─ ─ TAFI 709525 ─ ─ 540 70 95 25 ─ 1 80 0.3 75 78 90 59 400 137 000 5 000 LRT   708025
─ ─ ─ TAFI 709535 ─ ─ 755 70 95 35 ─ 1 80 1 75 78 90 78 100 195 000 5 000 LRT   708035
70
NA 4914 ─ ─ ─ ─ ─ 765 70 100 30 ─ 1 80 1.5 75 78 95 83 200 158 000 5 000 LRT   708030
─ NA 6914 ─ ─ ─ ─ 1 400 70 100 54 ─ 1 80 1 75 78 95 134 000 311 000 5 000 LRT   708054

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable axial shift amount of inner ring to outer ring
 　　 (3)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D37 1mm=0.03937inch
D38
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Inner Ring
B B
C C C C

r r
r r

r r r
r S

Fw

Fw
D

Da
Fw

da
D
Fw

d
D
D

d
d
r r r r

r r r r D
　 NA49  TAFI NA69 TRI GTRI

Shaft dia. 75 − 90mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) dimensions　mm load rating load rating rotational
speed(3)
dia.
NA 49 NA 69 NA 48 TAFI TRI GTRI (1) (2) da Da C C0
mm g d D C B rs min Fw S Min. Max. Max.
N N min-1

─ ─ ─ TAFI 7510525 ─ ─ 675 75 105 25 ─ 1 85 0.5 80   83 100 76 300 145 000 4 500 LRT     758525
NA 4915 ─ ─ ─ ─ ─ 810 75 105 30 ─ 1 85 1.5 80   83 100 86 200 169 000 4 500 LRT     758530
─ ─ ─ TAFI 7510535 ─ ─ 945 75 105 35 ─ 1 85 1.5 80   83 100 102 000 210 000 4 500 LRT     758535
75 ─ NA 6915 ─ ─ ─ ─ 1 480 75 105 54 ─ 1 85 1 80   83 100 138 000 331 000 4 500 LRT     758554
─ ─ ─ ─ TRI 7510845 ─ 1 340 75 108 45 45.5 1 83 2.5 80   81 103 146 000 270 000 5 000 LRT     758345
─ ─ ─ ─ ─ GTRI 7510845 1 440 75 108 45 45.5 1 83 ─ 80   81 103 190 000 396 000 1 800 LRTZ   758345
─ ─ ─ TAFI 8011025 ─ ─ 710 80 110 25 ─ 1 90 0.5 85   88 105 77 300 150 000 4 500 LRT     809025
NA 4916 ─ ─ ─ ─ ─ 855 80 110 30 ─ 1 90 1.5 85   88 105 87 300 175 000 4 500 LRT     809030
80
─ ─ ─ TAFI 8011035 ─ ─ 995 80 110 35 ─ 1 90 1.5 85   88 105 103 000 217 000 4 500 LRT     809035
─ NA 6916 ─ ─ ─ ─ 1 560 80 110 54 ─ 1 90 1 85   88 105 143 000 351 000 4 500 LRT     809054
─ ─ ─ TAFI 8511526 ─ ─ 775 85 115 26 ─ 1 95 1 90   93 110 79 700 159 000 4 000 LRT     859526
─ ─ ─ TAFI 8511536 ─ ─ 1 080 85 115 36 ─ 1 95 2 90   93 110 106 000 231 000 4 000 LRT     859536
NA 4917 ─ ─ ─ ─ ─ 1 280 85 120 35 ─ 1.1 100 1 91.5   98 113.5 110 000 244 000 4 000 LRT   8510035
─ NA 6917 ─ ─ ─ ─ 2 340 85 120 63 ─ 1.1 100 0.5 91.5   98 113.5 173 000 467 000 4 000 LRT   8510063
85
─ ─ ─ ─ TRI 8511850 ─ 1 640 85 118 50 50.5 1 93 3 90   91 113 165 000 329 000 4 500 LRT     859350
─ ─ ─ ─ TRI 8512045 ─ 1 610 85 120 45 45.5 1.5 95 2.5 93   93.5 112 155 000 305 000 4 000 LRT     859545
─ ─ ─ ─ ─ GTRI 8511850 1 780 85 118 50 50.5 1 93 ─ 90   91 113 224 000 509 000 1 600 LRTZ   859350
─ ─ ─ ─ ─ GTRI 8512045 1 720 85 120 45 45.5 1.5 95 ─ 93   93.5 112 204 000 455 000 1 600 LRTZ   859545
─ ─ ─ TAFI 9012026 ─ ─ 820 90 120 26 ─ 1 100 1 95   98 115 82 400 168 000 4 000 LRT   9010026
─ ─ ─ TAFI 9012036 ─ ─ 1 140 90 120 36 ─ 1 100 2 95   98 115 110 000 244 000 4 000 LRT   9010036
NA 4918 ─ ─ ─ ─ ─ 1 350 90 125 35 ─ 1.1 105 1 96.5 103 118.5 113 000 258 000 4 000 LRT   9010535
90
─ ─ ─ ─ TRI 9012550 ─ 1 870 90 125 50 50.5 1.5 100 3 98   98.5 117 172 000 355 000 4 000 LRT   9010050
─ NA 6918 ─ ─ ─ ─ 2 460 90 125 63 ─ 1.1 105 0.5 96.5 103 118.5 178 000 490 000 4 000 LRT   9010563
─ ─ ─ ─ ─ GTRI 9012550 2 020 90 125 50 50.5 1.5 100 ─ 98   98.5 117 234 000 549 000 1 500 LRTZ 9010050

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable axial shift amount of inner ring to outer ring
 　　 (3)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D39 1mm=0.03937inch
D40
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Inner Ring
B B
C C C C

r r
r r
r r
r r S

Fw

Fw
D

Da
da
D
d

d
Fw
Fw

D
D

d
d
r r

D
r r

r r r r

NA49  TAFI NA69 TRI GTRI

NA48
Shaft dia. 95 − 150mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) dimensions　mm load rating load rating rotational
speed(3)
dia.
NA 49 NA 69 NA 48 TAFI TRI GTRI (1) (2) da Da C C0
mm g d D C B rs min Fw S Min. Max. Max.
N N min-1

─ ─ ─ TAFI   9512526 ─ ─ 860 95 125 26 ─ 1 105 1 100 103 120 84 700 178 000 4 000 LRT     9510526
─ ─ ─ TAFI   9512536 ─ ─ 1 190 95 125 36 ─ 1 105 2 100 103 120 113 000 258 000 4 000 LRT     9510536
95
NA 4919 ─ ─ ─ ─ ─ 1 420 95 130 35 ─ 1.1 110 1 101.5 108 123.5 116 000 271 000 3 500 LRT     9511035
─ NA 6919 ─ ─ ─ ─ 2 580 95 130 63 ─ 1.1 110 0.5 101.5 108 123.5 182 000 514 000 3 500 LRT     9511063
─ ─ ─ TAFI 10013030 ─ ─ 1 040 100 130 30 ─ 1 110 0.5 105 108 125 106 000 240 000 3 500 LRT   10011030
─ ─ ─ TAFI 10013040 ─ ─ 1 380 100 130 40 ─ 1 110 1.5 105 108 125 134 000 324 000 3 500 LRT   10011040
100 ─ ─ ─ ─ TRI 10013550 ─ 2 040 100 135 50 50.5 1.5 110 3 108 108.5 127 183 000 395 000 3 500 LRT   10011050
NA 4920 ─ ─ ─ ─ ─ 1 960 100 140 40 ─ 1.1 115 1 106.5 113 133.5 145 000 329 000 3 500 LRT   10011540
─ ─ ─ ─ ─ GTRI 10013550 2 200 100 135 50 50.5 1.5 110 ─ 108 108.5 127 245 000 603 000 1 400 LRTZ 10011050
─ ─ ─ ─ TRI 10515350 ─ 3 020 105 153 50 50.5 1.5 115 3 113 113.5 145 233 000 414 000 3 500 LRT   10511550
105
─ ─ ─ ─ ─ GTRI 10515350 3 270 105 153 50 50.5 1.5 115 ─ 113 113.5 145 315 000 614 000 1 300 LRTZ 10511550
─ ─ NA 4822 ─ ─ ─ 1 200 110 140 30 ─ 1 120 1 115 118 135 93 200 239 000 3 500 LRT   11012030
110
NA 4922 ─ ─ ─ ─ ─ 2 120 110 150 40 ─ 1.1 125 1 116.5 123 143.5 152 000 357 000 3 000 LRT   11012540
─ ─ NA 4824 ─ ─ ─ 1 300 120 150 30 ─ 1 130 1 125 128 145 96 900 259 000 3 000 LRT   12013030
120
NA 4924 ─ ─ ─ ─ ─ 2 960 120 165 45 ─ 1.1 135 2 126.5 133 158.5 187 000 435 000 3 000 LRT   12013545
─ ─ ─ ─ TRI 12517860 ─ 4 780 125 178 60 60.5 1.5 140 2.5 133 138 170 307 000 625 000 3 000 LRT   12514060
125
─ ─ ─ ─ ─ GTRI 12517860 5 180 125 178 60 60.5 1.5 140 ─ 133 138 170 409 000 923 000 1 100 LRTZ 12514060
─ ─ NA 4826 ─ ─ ─ 1 960 130 165 35 ─ 1.1 145 1 136.5 143 158.5 116 000 340 000 3 000 LRT   13014535
130
NA 4926 ─ ─ ─ ─ ─ 4 030 130 180 50 ─ 1.5 150 2.5 138 148 172 215 000 540 000 2 500 LRT   13015050
─ ─ ─ ─ TRI 13518860 ─ 5 100 135 188 60 60.5 1.5 150 2.5 143 148 180 320 000 675 000 2 500 LRT   13515060
135
─ ─ ─ ─ ─ GTRI 13518860 5 530 135 188 60 60.5 1.5 150 ─ 143 148 180 423 000 989 000 1 000 LRTZ 13515060
─ ─ NA 4828 ─ ─ ─ 2 100 140 175 35 ─ 1.1 155 1 146.5 153 168.5 120 000 363 000 2 500 LRT   14015535
140
NA 4928 ─ ─ ─ ─ ─ 4 290 140 190 50 ─ 1.5 160 2.5 148 158 182 224 000 580 000 2 500 LRT   14016050
─ ─ NA 4830 ─ ─ ─ 2 880 150 190 40 ─ 1.1 165 1.5 156.5 163 183.5 168 000 446 000 2 500 LRT   15016540
150
NA 4930 ─ ─ ─ ─ ─ 6 380 150 210 60 ─ 2 170 3 159 168 201 324 000 712 000 2 500 LRT   15017060
Notes(1)　　Minimum allowable value of chamfer dimension r
 　　 (2)　　Allowable axial shift amount of inner ring to outer ring
 　　 (3)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D41 1mm=0.03937inch
D42
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Inner Ring
C

r
S

Fw
D

Da
da
d
r

r
D
NA49  NA48

Shaft dia. 160 − 340mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) dimensions　mm load rating load rating rotational
speed(3)
dia.
NA 49 NA 69 NA 48 TAFI TRI GTRI (1) (2) da Da C C0
mm g d D C B rs min Fw S Min. Max. Max.
N N min-1

─ ─ NA 4832 ─ ─ ─ 3 050 160 200 40 ─ 1.1 175 1.5 166.5 173 193.5 173 000 474 000 2 500 LRT   16017540
160
NA 4932 ─ ─ ─ ─ ─ 6 750 160 220 60 ─ 2 180 3 169 178 211 337 000 761 000 1 900 LRT   16018060
─ ─ NA 4834 ─ ─ ─ 4 120 170 215 45 ─ 1.1 185 1.5 176.5 183 208.5 211 000 567 000 1 900 LRT   17018545
170
NA 4934 ─ ─ ─ ─ ─ 7 110 170 230 60 ─ 2 190 3 179 188 221 347 000 810 000 1 900 LRT   17019060
─ ─ NA 4836 ─ ─ ─ 4 340 180 225 45 ─ 1.1 195 1.5 186.5 193 218.5 218 000 602 000 1 900 LRT   18019545
180
NA 4936 ─ ─ ─ ─ ─ 10 200 180 250 69 ─ 2 205 3 189 203 241 434 000 989 000 1 900 LRT   18020569
─ ─ NA 4838 ─ ─ ─ 5 760 190 240 50 ─ 1.5 210 1.5 198 208 232 249 000 726 000 1 800 LRT   19021050
190
NA 4938 ─ ─ ─ ─ ─ 10 700 190 260 69 ─ 2 215 3 199 213 251 440 000 1 020 000 1 700 LRT   19021569
─ ─ NA 4840 ─ ─ ─ 6 040 200 250 50 ─ 1.5 220 1.5 208 218 242 255 000 766 000 1 600 LRT   20022050
200
NA 4940 ─ ─ ─ ─ ─ 15 400 200 280 80 ─ 2.1 225 4 211 223 269 518 000 1 120 000 1 600 LRT   20022580
─ ─ NA 4844 ─ ─ ─ 6 570 220 270 50 ─ 1.5 240 1.5 228 238 262 266 000 833 000 1 500 LRT   22024050
220
NA 4944 ─ ─ ─ ─ ─ 16 700 220 300 80 ─ 2.1 245 4 231 243 289 536 000 1 200 000 1 400 LRT   22024580
─ ─ NA 4848 ─ ─ ─ 10 200 240 300 60 ─ 2 265 2 249 262 291 345 000 1 150 000 1 300 LRT   24026560
240
NA 4948 ─ ─ ─ ─ ─ 18 000 240 320 80 ─ 2.1 265 4 251 262 309 565 000 1 320 000 1 300 LRT   24026580
─ ─ NA 4852 ─ ─ ─ 11 000 260 320 60 ─ 2 285 2 269 282 311 354 000 1 220 000 1 100 LRT   26028560
260
NA 4952 ─ ─ ─ ─ ─ 31 100 260 360 100 ─ 2.1 290 4 271 287 349 847 000 1 900 000 1 100 LRT 260290100
─ ─ NA 4856 ─ ─ ─ 15 800 280 350 69 ─ 2 305 2.5 289 302 341 486 000 1 550 000 950 LRT   28030569
280
NA 4956 ─ ─ ─ ─ ─ 33 100 280 380 100 ─ 2.1 310 4 291 307 369 877 000 2 040 000 950 LRT 280310100
─ ─ NA 4860 ─ ─ ─ 22 300 300 380 80 ─ 2.1 330 2.5 311 327 369 610 000 1 900 000 900 LRT   30033080
300
NA 4960 ─ ─ ─ ─ ─ 51 400 300 420 118 ─ 3 340 4 313 337 407 1 130 000 2 650 000 850 LRT 300340118
─ ─ NA 4864 ─ ─ ─ 23 700 320 400 80 ─ 2.1 350 2.5 331 347 389 635 000 2 040 000 750 LRT   32035080
320
NA 4964 ─ ─ ─ ─ ─ 54 400 320 440 118 ─ 3 360 4 333 357 427 1 170 000 2 830 000 750 LRT 320360118
─ ─ NA 4868 ─ ─ ─ 25 000 340 420 80 ─ 2.1 370 2.5 351 367 409 651 000 2 140 000 700 LRT   34037080
340
NA 4968 ─ ─ ─ ─ ─ 57 300 340 460 118 ─ 3 380 4 353 377 447 1 220 000 3 020 000 700 LRT 340380118

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable axial shift amount of inner ring to outer ring
 　　 (3)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D43 1mm=0.03937inch
D44
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Inner Ring
C

r
S

Fw
D

Da
da
d
r

r
D
NA49  NA48

Shaft dia. 360 − 440mm

Identification number Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) dimensions　mm load rating load rating rotational
speed(3)
dia.
NA 49 NA 69 NA 48 TAFI TRI GTRI (1) (2) da Da C C0
mm g d D C B rs min Fw S Min. Max. Max.
N N min-1

─ ─ NA 4872 ─ ─ ─ 26 400 360 440 80 ─ 2.1 390 2.5 371 387 429 680 000 2 320 000 650 LRT   36039080
360
NA 4972 ─ ─ ─ ─ ─ 60 200 360 480 118 ─ 3 400 4 373 397 467 1 260 000 3 200 000 600 LRT 360400118
─ ─ NA 4876 ─ ─ ─ 44 600 380 480 100 ─ 2.1 415 3 391 412 469 951 000 2 860 000 600 LRT 380415100
380
NA 4976 ─ ─ ─ ─ ─ 90 300 380 520 140 ─ 4 430 5 396 427 504 1 540 000 4 030 000 500 LRT 380430140
400 NA 4980 ─ ─ ─ ─ ─ 94 400 400 540 140 ─ 4 450 5 416 447 524 1 590 000 4 270 000 500 LRT 400450140
420 NA 4984 ─ ─ ─ ─ ─ 98 500 420 560 140 ─ 4 470 5 436 467 544 1 640 000 4 510 000 500 LRT 420470140
440 NA 4988 ─ ─ ─ ─ ─ 131 000 440 600 160 ─ 4 490 5 456 487 584 1 910 000 5 140 000 400 LRT 440490160

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable axial shift amount of inner ring to outer ring
 　　 (3)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D45 1mm=0.03937inch
D46
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring, Inch Series
C

ra
Fw

Da
D
D
BR

Shaft dia. 15.875 − 47.625mm

Mass Boundary dimensions　mm(inch) Standard mounting Basic dynamic Basic static Allowable
(Ref.) dimensions　mm load rating load rating rotational
speed(2)
Shaft dia. Identification
( ) 1 C C0
mm number Da ras max
(inch) g Fw D C 　
Max. N N min-1

15.875      
BR 101812   49 15.875（ 5╱8 ） 28.575（1 1╱ 8 ） 19.050（ 3╱ 4 ） 24.5 0.6 18 900 19 700 25 000
（ 5╱8）   
19.050 BR 122012   56 19.050（  3╱4 ） 31.750（1  1╱4 ） 19.050（  3╱4 ） 26.5 1 21 700 24 400 20 000
（ 3╱4 ） BR 122016   75 19.050（  3╱4 ） 31.750（1  1╱4 ） 25.400（1 ） 26.5 1 27 600 33 100 20 000
22.225 BR 142212   63 22.225（  7╱8 ） 34.925（1  3╱8 ） 19.050（  3╱4 ） 29.7 1 23 000 27 100 18 000
（ 7╱8 ） BR 142216   84.5 22.225（  7╱8 ） 34.925（1  3╱8 ） 25.400（1 ） 29.7 1 29 100 36 800 18 000
25.400 BR 162412   69 25.400（1 ） 38.100（1  1╱2 ） 19.050（  3╱4 ） 32.9 1 25 300 31 900 16 000
（1） BR 162416   92.5 25.400（1 ） 38.100（1  1╱2 ） 25.400（1 ） 32.9 1 32 100 43 300 16 000
28.575 BR 182616 102 28.575（1  1╱8 ） 41.275（1  5╱8 ） 25.400（1 ） 36 1 34 900 49 900 14 000
（1 1╱8 ） BR 182620 128 28.575（1  1╱8 ） 41.275（1  5╱8 ） 31.750（1  1╱4 ） 36 1 43 200 65 600 14 000
31.750 BR 202816 110 31.750（1  1╱4 ） 44.450（1  3╱4 ） 25.400（1 ） 39.2 1 36 000 53 500 13 000
（1 1╱4 ） BR 202820 138 31.750（1  1╱4 ） 44.450（1  3╱4 ） 31.750（1  1╱4 ） 39.2 1 44 600 70 300 13 000
34.925 BR 223016 119 34.925（1  3╱8 ） 47.625（1  7╱8 ） 25.400（1 ） 42.4 1 38 500 60 000 11 000
（1 3╱8 ） BR 223020 149 34.925（1  3╱8 ） 47.625（1  7╱8 ） 31.750（1  1╱4 ） 42.4 1 47 700 78 900 11 000
38.100 BR 243316 149 38.100（1  1╱2 ） 52.388（2  1╱16 ） 25.400（1 ） 45.1 1.5 43 700 66 900 11 000
（1 1╱2 ） BR 243320 187 38.100（1  1╱2 ） 52.388（2  1╱16 ） 31.750（1  1╱4 ） 45.1 1.5 54 200 88 200 11 000
41.275 BR 263516 158 41.275（1  5╱8 ） 55.562（2  3╱16 ） 25.400（1 ） 48.3 1.5 44 800 70 900 9 500
（1 5╱8 ） BR 263520 199 41.275（1  5╱8 ） 55.562（2  3╱16 ） 31.750（1  1╱4 ） 48.3 1.5 55 600 93 400 9 500

44.450 BR 283716 170 44.450（1  3╱4 ） 58.738（2  5╱16 ） 25.400（1 ） 51.5 1.5 47 500 78 200 9 000
BR 283720 215 44.450（1  3╱4 ） 58.738（2  5╱16 ） 31.750（1  1╱4 ） 51.5 1.5 58 900 103 000 9 000
（1 3╱4 ）
BR 283820 250 44.450（1  3╱4 ） 60.325（2  3╱8 ） 31.750（1  1╱4 ） 53.1 1.5 58 900 103 000 9 000
47.625
BR 303920 225 47.625（1  7╱8 ） 61.912（2  7╱16 ） 31.750（1  1╱4 ） 54.7 1.5 60 100 108 000 8 500
（1 7╱8 ）

Notes(1)　　Maximum permissible corner radius of the housing

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D47 1mm=0.03937inch
D48
 MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring, Inch Series
C

ra
Fw

Da
D
D
BR

Shaft dia. 50.800 − 101.600mm

Mass Boundary dimensions　mm(inch) Standard mounting Basic dynamic Basic static Allowable
(Ref.) dimensions　mm load rating load rating rotational
speed(2)
Shaft dia. Identification
( )
1 C C0
mm number Da ras max
(inch) g Fw D C 　
Max. N N min-1

50.800 BR 324116 190 50.800（2 ） 65.088（2  9╱16 ） 25.400（1 ） 57.8 1.5 51 000 89 400 8 000
（2） BR 324120 240 50.800（2 ） 65.088（2  9╱16 ） 31.750（1  1╱4 ） 57.8 1.5 63 200 118 000 8 000
57.150 BR 364824 435 57.150（2  1╱4 ） 76.200（3 ） 38.100（1  1╱2 ） 69 1.5 90 300 158 000 7 000
（2 1╱4 ） BR 364828 510 57.150（2  1╱4 ） 76.200（3 ） 44.450（1  3╱4 ） 69 1.5 105 000 191 000 7 000
63.500 BR 405224 475 63.500（2  1╱2 ） 82.550（3  1╱4） 38.100（1  1╱2 ） 74.3 2 94 600 174 000 6 500
（2 1╱2 ） BR 405228 555 63.500（2  1╱2 ） 82.550（3  1╱4 ） 44.450（1  3╱4 ） 74.3 2 110 000 210 000 6 500
69.850 BR 445624 510 69.850（2  3╱4 ） 88.900（3  1╱2 ） 38.100（1  1╱2 ） 80.7 2 98 700 189 000 5 500
（2 3╱4 ） BR 445628 600 69.850（2  3╱4 ） 88.900（3  1╱2 ） 44.450（1  3╱4 ） 80.7 2 114 000 228 000 5 500
76.200 BR 486024 555 76.200（3 ） 95.250（3  3╱4 ） 38.100（1  1╱2 ） 87 2 105 000 211 000 5 500
（3） BR 486028 650 76.200（3 ） 95.250（3  3╱4 ） 44.450（1  3╱4 ） 87 2 122 000 255 000 5 500
82.550 BR 526828 990 82.550（3  1╱4 ） 107.950（4  1╱4 ） 44.450（1  3╱4 ） 99.7 2 141 000 259 000 5 000
（3 1╱4 ） BR 526832 1 140 82.550（3  1╱4 ） 107.950（4  1╱4 ） 50.800（2 ） 99.7 2 154 000 290 000 5 000
88.900    
BR 567232 1 220 88.900（3 1╱2 ） 114.300（4 1╱2 ） 50.800（2 ） 106.1 2 162 000 316 000 4 500
（3 1╱2 ）
95.250    
BR 607632 1 290 95.250（3 3╱4 ） 120.650（4 3╱4 ） 50.800（2 ） 111.4 2.5 169 000 342 000 4 000
（3 3╱4 ）
101.600
BR 648032 1 370 101.600（4 ） 127.000（5 ） 50.800（2 ） 117.8 2.5 176 000 368 000 4 000
（4）

Notes(1)　　Maximum permissible corner radius of the housing

 　　 (2)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　In bearings with a roller set bore diameter Fw of 69.850 mm or less, the outer ring has an oil groove and an oil hole. In others, the
outer ring has an oil groove and two oil holes.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D49 1mm=0.03937inch
D50
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Inner Ring, Inch Series
B
C

ra
S

ra
Fw

Da
D

da
d
D
BRI

Shaft dia. 9.525 − 41.275mm

Mass Boundary dimensions　mm(inch) Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
(Ref.) dimensions　mm load rating load rating rotational
speed(3)
Shaft dia. Identification (1) ( ) C C0
da
2
mm number Da ras max
d D C B Fw S
(inch) g Min. Max. Max. 　 N N min-1

9.525      
9.525（ 3╱8 ） 28.575（1 1╱8 ） 19.050（ 3╱4 ） 19.300 15.875（ 5╱8 ） 0.3

BRI  61812   67.5 14 14.5 24.5 0.6 18 900 19 700 25 000 LRB 61012
（ 3╱8 ）
12.700 BRI  82012   79.5 12.700（  1╱ 2 ） 31.750（1  1╱ 4 ） 19.050（  3╱ 4 ） 19.300 19.050（  3╱ 4 ） 0.3 17.5 18 26.5 1 21 700 24 400 20 000 LRB 81212
（ 1╱2 ） BRI  82016 106 12.700（  1╱ 2 ） 31.750（1  1╱ 4 ） 25.400（1 ） 25.650 19.050（  3╱ 4 ） 0.5 17.5 18 26.5 1 27 600 33 100 20 000 LRB 81216
15.875 BRI 102212   91 15.875（  5╱ 8 ） 34.925（1  3╱ 8 ） 19.050（  3╱ 4 ） 19.300 22.225（  7╱ 8 ） 0.3 21 21.2 29.7 1 23 000 27 100 18 000 LRB 101412
（ 5╱8 ） BRI 102216 122 15.875（  5╱ 8 ） 34.925（1  3╱ 8 ） 25.400（1 ） 25.650 22.225（  7╱ 8 ） 0.5 21 21.2 29.7 1 29 100 36 800 18 000 LRB 101416
19.050 BRI 122412 102 19.050（  3╱ 4 ） 38.100（1  1╱ 2 ） 19.050（  3╱ 4 ） 19.300 25.400（1 ） 0.3 24 24.4 32.9 1 25 300 31 900 16 000 LRB 121612
（ 3╱4） BRI 122416 136 19.050（  3╱ 4 ） 38.100（1  1╱ 2 ） 25.400（1 ） 25.650 25.400（1 ） 0.5 24 24.4 32.9 1 32 100 43 300 16 000 LRB 121616
22.225 BRI 142616 152 22.225（  7╱ 8 ） 41.275（1  5╱ 8 ） 25.400（1 ） 25.650 28.575（1  1╱ 8 ） 0.5 27 27.5 36 1 34 900 49 900 14 000 LRB 141816
（ 7╱8 ） BRI 142620 190 22.225（  7╱ 8 ） 41.275（1  5╱ 8 ） 31.750（1  1╱ 4 ） 32.000 28.575（1  1╱ 8 ） 0.5 27 27.5 36 1 43 200 65 600 14 000 LRB 141820
25.400 BRI 162816 166 25.400（1 ） 44.450（1  3╱ 4 ） 25.400（1 ） 25.650 31.750（1  1╱ 4 ） 0.5 30.5 30.7 39.2 1 36 000 53 500 13 000 LRB 162016
（1） BRI 162820 210 25.400（1 ） 44.450（1  3╱ 4 ） 31.750（1  1╱ 4 ） 32.000 31.750（1  1╱ 4 ） 0.5 30.5 30.7 39.2 1 44 600 70 300 13 000 LRB 162020
28.575 BRI 183016 182 28.575（1  1╱ 8 ） 47.625（1  7╱ 8 ） 25.400（1 ） 25.650 34.925（1  3╱ 8 ） 0.5 33.5 33.9 42.4 1 38 500 60 000 11 000 LRB 182216
（1 1╱8 ） BRI 183020 225 28.575（1  1╱ 8 ） 47.625（1  7╱ 8 ） 31.750（1  1╱ 4 ） 32.000 34.925（1  3╱ 8 ） 0.5 33.5 33.9 42.4 1 47 700 78 900 11 000 LRB 182220
31.750 BRI 203316 220 31.750（1  1╱ 4 ） 52.388（2  1╱16 ） 25.400（1 ） 25.650 38.100（1  1╱ 2 ） 0.5 37 37.1 45.1 1.5 43 700 66 900 11 000 LRB 202416
（1 1╱4 ） BRI 203320 275 31.750（1  1╱ 4 ） 52.388（2  1╱16 ） 31.750（1  1╱ 4 ） 32.000 38.100（1  1╱ 2 ） 0.5 37 37.1 45.1 1.5 54 200 88 200 11 000 LRB 202420
34.925 BRI 223516 235 34.925（1  3╱ 8 ） 55.562（2  3╱16 ） 25.400（1 ） 25.650 41.275（1  5╱ 8 ） 0.5 40.2 40.2 48.3 1.5 44 800 70 900 9 500 LRB 222616
（1 3╱8 ） BRI 223520 295 34.925（1  3╱ 8 ） 55.562（2  3╱16 ） 31.750（1  1╱ 4 ） 32.000 41.275（1  5╱ 8 ） 0.5 40.2 40.2 48.3 1.5 55 600 93 400 9 500 LRB 222620
BRI 243716 250 38.100（1  1╱ 2 ） 58.738（2  5╱16 ） 25.400（1 ） 25.650 44.450（1  3╱ 4 ） 0.5 43.3 43.4 51.5 1.5 47 500 78 200 9 000 LRB 242816
38.100 BRI 243720 315 38.100（1  1╱ 2 ） 58.738（2  5╱16 ） 31.750（1  1╱ 4 ） 32.000 44.450（1  3╱ 4 ） 0.5 43.3 43.4 51.5 1.5 58 900 103 000 9 000 LRB 242820
（1 1╱2 ） BRI 243820 350 38.100（1  1╱ 2 ） 60.325（2  3╱ 8 ） 31.750（1  1╱ 4 ） 32.000 44.450（1  3╱ 4 ） 0.5 43.3 43.4 53.1 1.5 58 900 103 000 9 000 LRB 242820
BRI 243920 380 38.100（1  1╱ 2 ） 61.912（2  7╱16 ） 31.750（1  1╱ 4 ） 32.000 47.625（1  7╱ 8 ） 0.5 43.3 43.4 54.7 1.5 60 100 108 000 8 500 LRB 243020
41.275 BRI 264116 325 41.275（1  5╱ 8 ） 65.088（2  9╱16 ） 25.400（1 ） 25.650 50.800（2 ） 0.5 48 49 57.8 1.5 51 000 89 400 8 000 LRB 263216
（1 5╱8 ） BRI 264120 410 41.275（1  5╱ 8 ） 65.088（2  9╱16 ） 31.750（1  1╱ 4 ） 32.000 50.800（2 ） 0.5 48 49 57.8 1.5 63 200 118 000 8 000 LRB 263220

Notes(1)　　Allowable axial shift amount of inner ring to outer ring

 　　 (2)　　Maximum permissible corner radius of the shaft or housing
 　　 (3)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The inner ring and the outer ring each have an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D51 1mm=0.03937inch
D52
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Inner Ring, Inch Series
B
C

ra
S

ra
Fw
D

Da
da
d
D
BRI

Shaft dia. 44.450 − 88.900mm

Mass Boundary dimensions　mm(inch) Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
(Ref.) dimensions　mm load rating load rating rotational
speed(3)
Shaft dia. Identification
( )
2 C C0
mm number da Da ras max
(inch) g d D C B Fw S(1) 　
Min. Max. Max. N N min-1

44.450 BRI 284824   735 44.450（1  3╱ 4 ） 76.200（3 ） 38.100（1  1╱ 2 ） 38.350 57.150（2  1╱ 4 ） 1 52.5 55 69 1.5 90 300 158 000 7 000 LRB 283624
（1 3╱4 ） BRI 284828 855 44.450（1  3╱ 4 ） 76.200（3 ） 44.450（1  3╱ 4 ） 44.700 57.150（2  1╱ 4 ） 1 52.5 55 69 1.5 105 000 191 000 7 000 LRB 283628
50.800 BRI 325224 810 50.800（2 ） 82.550（3  1╱ 4 ） 38.100（1  1╱ 2 ） 38.350 63.500（2  1╱ 2 ） 1 58 61 74.3 2 94 600 174 000 6 500 LRB 324024
（2） BRI 325228 945 50.800（2 ） 82.550（3  1╱ 4 ） 44.450（1  3╱ 4 ） 44.700 63.500（2  1╱ 2 ） 1 58 61 74.3 2 110 000 210 000 6 500 LRB 324028
57.150 BRI 365624 885 57.150（2  1╱ 4 ） 88.900（3  1╱ 2 ） 38.100（1  1╱ 2 ） 38.350 69.850（2  3╱ 4 ） 1 65 67 80.7 2 98 700 189 000 5 500 LRB 364424
（2 1╱4 ） BRI 365628 1 040 57.150（2  1╱ 4 ） 88.900（3  1╱ 2 ） 44.450（1  3╱ 4 ） 44.700 69.850（2  3╱ 4 ） 1 65 67 80.7 2 114 000 228 000 5 500 LRB 364428
63.500 BRI 406024 965 63.500（2  1╱ 2 ） 95.250（3  3╱ 4 ） 38.100（1  1╱ 2 ） 38.350 76.200（3 ） 1 71 73 87 2 105 000 211 000 5 500 LRB 404824
（2 1╱2 ） BRI 406028 1 130 63.500（2  1╱ 2 ） 95.250（3  3╱ 4 ） 44.450（1  3╱ 4 ） 44.700 76.200（3 ） 1 71 73 87 2 122 000 255 000 5 500 LRB 404828
69.850 BRI 446828 1 520 69.850（2  3╱ 4 ） 107.950（4  1╱ 4 ） 44.450（1  3╱ 4 ） 44.700 82.550（3  1╱ 4 ） 1.5 77 79 99.7 2 141 000 259 000 5 000 LRB 445228
（2 3╱4 ） BRI 446832 1 740 69.850（2  3╱ 4 ） 107.950（4  1╱ 4 ） 50.800（2 ） 51.050 82.550（3  1╱ 4 ） 3 77 79 99.7 2 154 000 290 000 5 000 LRB 445232
76.200
BRI 487232 1 860 76.200（3 ） 114.300（4   1╱ 2 ） 50.800（2 ） 51.050 88.900（3   1╱ 2 ） 3 83.5 86 106.1 2 162 000 316 000 4 500 LRB 485632
（3）
82.550
BRI 527632 1 980 82.550（3   1╱ 4 ） 120.650（4   3╱ 4 ） 50.800（2 ） 51.050 95.250（3   3╱ 4 ） 3 91 93 111.4 2.5 169 000 342 000 4 000 LRB 526032
（3 1╱4 ）
88.900
BRI 568032 2 120 88.900（3   1╱ 2 ） 127.000（5 ） 50.800（2 ） 51.050 101.600（4 ） 3 97 99 117.8 2.5 176 000 368 000 4 000 LRB 566432
（3 1╱2 ）

Notes(1)　　Allowable axial shift amount of inner ring to outer ring

 　　 (2)　　Maximum permissible corner radius of the shaft or housing
 　　 (3)　　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　In bearings with a bearing bore diameter, d, of 57.150 mm or less, the outer ring has an oil groove and an oil hole. In bearings with
a bearing bore diameter, d, of 76.200 mm or less, the inner ring has an oil groove and an oil hole. In others, the inner ring and the
outer ring each have an oil groove and two oil holes.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D53 1mm=0.03937inch
D54
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Seal, Without Inner Ring
C C C C

r r r r

Fw

Fw

Fw

Fw
D
D

D
D

Da
r r r r
D
RNA49 … UU RNA49 … U RNA69 … UU RNA69 … U
RNA69 … UU(Fw ≦ 35) RNA69 … U(Fw ≦ 35)

Shaft dia. 14 − 45mm

Identification number Mass Boundary dimensions Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) mm dimension load rating load rating rotational
Da speed(2)
dia. With two seals With one seal With two seals With one seal (1)
C C0
mm g Fw D C rs min Max.
mm N N min-1

14 RNA 4900UU RNA 4900U ─ ─ 16.3 14 22 13 0.3 20 8 080 8 490 14 000

16 RNA 4901UU RNA 4901U ─ ─ 17.9 16 24 13 0.3 22 8 470 9 320 12 000

─ ─ RNA 6901UU RNA 6901U 30 16 24 22 0.3 22 15 500 20 400 12 000
18 RNA 49/14UU RNA 49/14U ─ ─ 19.7 18 26 13 0.3 24 9 260 10 800 11 000

20 RNA 4902UU RNA 4902U ─ ─ 21.5 20 28 13 0.3 26 9 570 11 600 9 500

─ ─ RNA 6902UU RNA 6902U 37.5 20 28 23 0.3 26 18 500 27 100 9 500

22 RNA 4903UU RNA 4903U ─ ─ 23 22 30 13 0.3 28 10 300 13 100 8 500

─ ─ RNA 6903UU RNA 6903U 40.5 22 30 23 0.3 28 19 800 30 600 8 500

25 RNA 4904UU RNA 4904U ─ ─ 54.5 25 37 17 0.3 35 18 000 20 500 7 500

─ ─ RNA 6904UU RNA 6904U 95.5 25 37 30 0.3 35 33 000 44 600 7 500

28 RNA 49/22UU RNA 49/22U ─ ─ 55.5 28 39 17 0.3 37 18 300 23 700 7 000

─ ─ RNA 69/22UU RNA 69/22U 97.5 28 39 30 0.3 37 33 800 52 000 7 000

30 RNA 4905UU RNA 4905U ─ ─ 63 30 42 17 0.3 40 20 300 25 100 6 500

─ ─ RNA 6905UU RNA 6905U 111 30 42 30 0.3 40 39 200 58 700 6 500

32 RNA 49/28UU RNA 49/28U ─ ─ 75.5 32 45 17 0.3 43 21 000 26 800 6 000

─ ─ RNA 69/28UU RNA 69/28U 133 32 45 30 0.3 43 38 900 59 100 6 000

35 RNA 4906UU RNA 4906U ─ ─ 71 35 47 17 0.3 45 21 500 28 400 5 500

─ ─ RNA 6906UU RNA 6906U 125 35 47 30 0.3 45 40 100 63 000 5 500

40 RNA 49/32UU RNA 49/32U ─ ─ 94.5 40 52 20 0.6 48 29 400 44 200 5 000

─ ─ RNA 69/32UU RNA 69/32U 170 40 52 36 0.6 48 50 300 88 300 5 000

42 RNA 4907UU RNA 4907U ─ ─ 112 42 55 20 0.6 51 30 100 46 300 4 500

─ ─ RNA 6907UU RNA 6907U 200 42 55 36 0.6 51 51 600 92 600 4 500
45 RNA 49/38UU RNA 49/38U ─ ─ 119 45 58 20 0.6 54 31 600 50 400 4 000

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to grease lubrication.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　Bearings are provided with prepacked grease. Bearings with a seal on one side are not provided with prepacked grease. Perform
proper lubrication for use.

1N=0.102kgf=0.2248lbs.
D55 1mm=0.03937inch
D56
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Seal, Without Inner Ring
C C C C

r r r r

Fw

Fw

Fw

Fw
D
D

D
D

Da
r r r r
D
RNA49 … UU RNA49 … U RNA69 … UU RNA69 … U

Shaft dia. 48 − 85mm

Identification number Mass Boundary dimensions Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) mm dimension load rating load rating rotational
Da speed(2)
dia. With two seals With one seal With two seals With one seal (1)
C C0
mm g Fw D C rs min Max.
mm N N min-1

48 RNA 4908UU RNA 4908U ─ ─ 150 48 62 22 0.6 58 37 200 58 400 4 000

─ ─ RNA 6908UU RNA 6908U 270 48 62 40 0.6 58 63 700 117 000 4 000
50 RNA 49/42UU RNA 49/42U ─ ─ 173 50 65 22 0.6 61 38 000 60 900 4 000

52 RNA 4909UU RNA 4909U − ─ 197 52 68 22 0.6 64 38 900 63 400 3 500

─ ─ RNA 6909UU RNA 6909U 355 52 68 40 0.6 64 66 600 127 000 3 500
55 RNA 49/48UU RNA 49/48U ─ ─ 187 55 70 22 0.6 66 39 600 66 100 3 500

58 RNA 4910UU RNA 4910U ─ ─ 177 58 72 22 0.6 68 41 300 71 100 3 500

─ ─ RNA 6910UU RNA 6910U 320 58 72 40 0.6 68 70 800 142 000 3 500
60 RNA 49/52UU RNA 49/52U ─ ─ 200 60 75 22 0.6 71 42 100 73 600 3 000

63 RNA 4911UU RNA 4911U ─ ─ 265 63 80 25 1 75 52 200 85 700 3 000

─ ─ RNA 6911UU RNA 6911U 470 63 80 45 1 75 89 400 171 000 3 000
65 RNA 49/58UU RNA 49/58U ─ ─ 275 65 82 25 1 77 53 400 89 200 3 000

68 RNA 4912UU RNA 4912U ─ ─ 285 68 85 25 1 80 54 500 92 800 3 000

─ ─ RNA 6912UU RNA 6912U 505 68 85 45 1 80 93 400 186 000 3 000
70 RNA 49/62UU RNA 49/62U ─ ─ 320 70 88 25 1 83 55 700 96 300 2 500

72 RNA 4913UU RNA 4913U ─ ─ 325 72 90 25 1 85 56 800 99 800 2 500

─ ─ RNA 6913UU RNA 6913U 580 72 90 45 1 85 97 400 200 000 2 500
75 RNA 49/68UU RNA 49/68U ─ ─ 465 75 95 30 1 90 73 900 133 000 2 500

80 RNA 4914UU RNA 4914U ─ ─ 495 80 100 30 1 95 76 900 143 000 2 500

─ ─ RNA 6914UU RNA 6914U 910 80 100 54 1 95 124 000 281 000 2 500

85 RNA 4915UU RNA 4915U ─ ─ 520 85 105 30 1 100 79 600 153 000 2 000

─ ─ RNA 6915UU RNA 6915U 960 85 105 54 1 100 128 000 299 000 2 000

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to grease lubrication.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　Bearings are provided with prepacked grease. Bearings with a seal on one side are not provided with prepacked grease. Perform
proper lubrication for use.

1N=0.102kgf=0.2248lbs.
D57 1mm=0.03937inch
D58
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Seal, Without Inner Ring
C C C C

r r r r

Fw

Fw

Fw

Fw
D
D

D
D

Da
r r r r
D
RNA49 … UU RNA49 … U RNA69 … UU RNA69 … U

Shaft dia. 90 − 160mm

Identification number Mass Boundary dimensions Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) mm dimension load rating load rating rotational
Da speed(2)
dia. With two seals With one seal With two seals With one seal C C0
(1)
mm g Fw D C rs min Max.
mm N N min-1

90 RNA 4916UU RNA 4916U ─ ─ 545 90 110 30 1 105 80 700 158 000 2 000

─ ─ RNA 6916UU RNA 6916U 1 010 90 110 54 1 105 132 000 317 000 2 000
95 RNA 49/82UU RNA 49/82U ─ ─ 570 95 115 30 1 110 83 200 168 000 2 000

100 RNA 4917UU RNA 4917U ─ ─ 695 100 120 35 1.1 113.5 103 000 225 000 1 900
─ ─ RNA 6917UU RNA 6917U 1 300 100 120 63 1.1 113.5 168 000 448 000 1 900

105 RNA 4918UU RNA 4918U ─ ─ 730 105 125 35 1.1 118.5 106 000 238 000 1 800
─ ─ RNA 6918UU RNA 6918U 1 360 105 125 63 1.1 118.5 172 000 471 000 1 800

110 RNA 4919UU RNA 4919U ─ ─ 760 110 130 35 1.1 123.5 109 000 250 000 1 700
─ ─ RNA 6919UU RNA 6919U 1 420 110 130 63 1.1 123.5 177 000 493 000 1 700
115 RNA 4920UU RNA 4920U ─ ─ 1 200 115 140 40 1.1 133.5 134 000 297 000 1 700
125 RNA 4922UU RNA 4922U ─ ─ 1 280 125 150 40 1.1 143.5 140 000 322 000 1 500
135 RNA 4924UU RNA 4924U ─ ─ 1 940 135 165 45 1.1 158.5 178 000 410 000 1 400
150 RNA 4926UU RNA 4926U ─ ─ 2 360 150 180 50 1.5 172 206 000 511 000 1 300
160 RNA 4928UU RNA 4928U ─ ─ 2 510 160 190 50 1.5 182 214 000 549 000 1 200

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to grease lubrication.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　Bearings are provided with prepacked grease. Bearings with a seal on one side are not provided with prepacked grease. Perform
proper lubrication for use.

1N=0.102kgf=0.2248lbs.
D59 1mm=0.03937inch
D60
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Seal, With Inner Ring B B B B
C C C C

r r r r

r r r r

Fw

Fw

Fw
Fw
D

da
D

Da
D
d
d

d
r r r r

r r r r
D
NA49 … UU NA49 … U NA69 … UU NA69 … U
NA69 … UU(d ≦ 30) NA69 … U(d ≦ 30)

Shaft dia. 10 − 40mm

Identification number Mass Boundary dimensions Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) mm dimensions　mm load rating load rating rotational
speed(2)
dia. With two seals With one seal With two seals With one seal (1) da Da C C0
mm g d D C B rs min Fw Min. Max. Max. N N min-1

10 NA 4900UU NA 4900U ─ ─ 24.5 10 22 13 14 0.3 14 12 13 20 8 080 8 490 14 000 LRTZ 101414

12 NA 4901UU NA 4901U ─ ─ 27.5 12 24 13 14 0.3 16 14 15 22 8 470 9 320 12 000 LRTZ 121614

─ ─ NA 6901UU NA 6901U 45.5 12 24 22 23 0.3 16 14 15 22 15 500 20 400 12 000 LRTZ 121623

15 NA 4902UU NA 4902U ─ ─ 36 15 28 13 14 0.3 20 17 19 26 9 570 11 600 9 500 LRTZ 152014

─ ─ NA 6902UU NA 6902U 62.5 15 28 23 24 0.3 20 17 19 26 18 500 27 100 9 500 LRTZ 152024

17 NA 4903UU NA 4903U ─ ─ 39.5 17 30 13 14 0.3 22 19 21 28 10 300 13 100 8 500 LRTZ 172214

─ ─ NA 6903UU NA 6903U 68.5 17 30 23 24 0.3 22 19 21 28 19 800 30 600 8 500 LRTZ 172224

20 NA 4904UU NA 4904U ─ ─ 78.5 20 37 17 18 0.3 25 22 24 35 18 000 20 500 7 500 LRTZ 202518

─ ─ NA 6904UU NA 6904U 137 20 37 30 31 0.3 25 22 24 35 33 000 44 600 7 500 LRTZ 202531

22 NA 49/22UU NA 49/22U ─ ─ 87.5 22 39 17 18 0.3 28 24 27 37 18 300 23 700 7 000 LRTZ 222818

─ ─ NA 69/22UU NA 69/22U 153 22 39 30 31 0.3 28 24 27 37 33 800 52 000 7 000 LRTZ 222831

25 NA 4905UU NA 4905U ─ ─ 92.5 25 42 17 18 0.3 30 27 29 40 20 300 25 100 6 500 LRTZ 253018

─ ─ NA 6905UU NA 6905U 162 25 42 30 31 0.3 30 27 29 40 39 200 58 700 6 500 LRTZ 253031

28 NA 49/28UU NA 49/28U ─ ─ 101 28 45 17 18 0.3 32 30 31 43 21 000 26 800 6 000 LRTZ 283218

─ ─ NA 69/28UU NA 69/28U 177 28 45 30 31 0.3 32 30 31 43 38 900 59 100 6 000 LRTZ 283231

30 NA 4906UU NA 4906U ─ ─ 106 30 47 17 18 0.3 35 32 34 45 21 500 28 400 5 500 LRTZ 303518

─ ─ NA 6906UU NA 6906U 185 30 47 30 31 0.3 35 32 34 45 40 100 63 000 5 500 LRTZ 303531

32 NA 49/32UU NA 49/32U ─ ─ 167 32 52 20 21 0.6 40 36 39 48 29 400 44 200 5 000 LRTZ 324021

─ ─ NA 69/32UU NA 69/32U 300 32 52 36 37 0.6 40 36 39 48 50 300 88 300 5 000 LRTZ 324037

35 NA 4907UU NA 4907U ─ ─ 179 35 55 20 21 0.6 42 39 41 51 30 100 46 300 4 500 LRTZ 354221

─ ─ NA 6907UU NA 6907U 320 35 55 36 37 0.6 42 39 41 51 51 600 92 600 4 500 LRTZ 354237
NA 4908UU NA 4908U ─ ─ 245 40 62 22 23 0.6 48 44 47 58 37 200 58 400 4 000 LRTZ 404823
40
─ ─ NA 6908UU NA 6908U 440 40 62 40 41 0.6 48 44 47 58 63 700 117 000 4 000 LRTZ 404841

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to grease lubrication.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　Bearings are provided with prepacked grease. Bearings with a seal on one side are not provided with prepacked grease. Perform
proper lubrication for use.

1N=0.102kgf=0.2248lbs.
D61 1mm=0.03937inch
D62
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Seal, With Inner Ring B B B B
C C C C

r r r r

r r r r

Fw

Fw
D

Fw
Fw

da

Da
d

D
D

D
d

d
d
r r r r

r r r r
D
NA49 … UU NA49 … U NA69 … UU NA69 … U

Shaft dia. 45 − 110mm

Identification number Mass Boundary dimensions Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) mm dimensions　mm load rating load rating rotational
speed(2)
dia. With two seals With one seal With two seals With one seal (1) da Da C C0
mm g d D C B rs min Fw Min. Max. Max. N N min-1

45 NA 4909UU NA 4909U ─ ─ 290 45 68 22 23 0.6 52 49 51 64 38 900 63 400 3 500 LRTZ 455223

─ ─ NA 6909UU NA 6909U 520 45 68 40 41 0.6 52 49 51 64 66 600 127 000 3 500 LRTZ 455241

50 NA 4910UU NA 4910U ─ ─ 295 50 72 22 23 0.6 58 54 57 68 41 300 71 100 3 500 LRTZ 505823

─ ─ NA 6910UU NA 6910U 530 50 72 40 41 0.6 58 54 57 68 70 800 142 000 3 500 LRTZ 505841

55 NA 4911UU NA 4911U ─ ─ 415 55 80 25 26 1 63 60 61 75 52 200 85 700 3 000 LRTZ 556326

─ ─ NA 6911UU NA 6911U 730 55 80 45 46 1 63 60 61 75 89 400 171 000 3 000 LRTZ 556346

60 NA 4912UU NA 4912U ─ ─ 445 60 85 25 26 1 68 65 66 80 54 500 92 800 3 000 LRTZ 606826

─ ─ NA 6912UU NA 6912U 785 60 85 45 46 1 68 65 66 80 93 400 186 000 3 000 LRTZ 606846

65 NA 4913UU NA 4913U ─ ─ 475 65 90 25 26 1 72 70 70.5 85 56 800 99 800 2 500 LRTZ 657226

─ ─ NA 6913UU NA 6913U 845 65 90 45 46 1 72 70 70.5 85 97 400 200 000 2 500 LRTZ 657246

70 NA 4914UU NA 4914U ─ ─ 770 70 100 30 31 1 80 75 78 95 76 900 143 000 2 500 LRTZ 708031
─ ─ NA 6914UU NA 6914U 1 400 70 100 54 55 1 80 75 78 95 124 000 281 000 2 500 LRTZ 708055

75 NA 4915UU NA 4915U ─ ─ 815 75 105 30 31 1 85 80 83 100 79 600 153 000 2 000 LRTZ 758531
─ ─ NA 6915UU NA 6915U 1 480 75 105 54 55 1 85 80 83 100 128 000 299 000 2 000 LRTZ 758555

80 NA 4916UU NA 4916U ─ ─ 860 80 110 30 31 1 90 85 88 105 80 700 158 000 2 000 LRTZ 809031
─ ─ NA 6916UU NA 6916U 1 570 80 110 54 55 1 90 85 88 105 132 000 317 000 2 000 LRTZ 809055

85 NA 4917UU NA 4917U ─ ─ 1 300 85 120 35 36 1.1 100 91.5 98 113.5 103 000 225 000 1 900 LRTZ 8510036
─ ─ NA 6917UU NA 6917U 2 360 85 120 63 64 1.1 100 91.5 98 113.5 168 000 448 000 1 900 LRTZ 8510064  

90 NA 4918UU NA 4918U ─ ─ 1 360 90 125 35 36 1.1 105 96.5 103 118.5 106 000 238 000 1 800 LRTZ 9010536
─ ─ NA 6918UU NA 6918U 2 480 90 125 63 64 1.1 105 96.5 103 118.5 172 000 471 000 1 800 LRTZ 9010564

95 NA 4919UU NA 4919U ─ ─ 1 420 95 130 35 36 1.1 110 101.5 108 123.5 109 000 250 000 1 700 LRTZ 9511036
─ ─ NA 6919UU NA 6919U 2 600 95 130 63 64 1.1 110 101.5 108 123.5 177 000 493 000 1 700 LRTZ 9511064
100 NA 4920UU NA 4920U ─ ─ 1 980 100 140 40 41 1.1 115 106.5 113 133.5 134 000 297 000 1 700 LRTZ 10011541
110 NA 4922UU NA 4922U ─ ─ 2 150 110 150 40 41 1.1 125 116.5 123 143.5 140 000 322 000 1 500 LRTZ 11012541
Notes(1)　　Minimum allowable value of chamfer dimension r
 　　 (2)　　Allowable rotational speed applies to grease lubrication.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　Bearings are provided with prepacked grease. Bearings with a seal on one side are not provided with prepacked grease. Perform
proper lubrication for use.

1N=0.102kgf=0.2248lbs.
D63 1mm=0.03937inch
D64
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Seal, With Inner Ring B B
C C

r r

r r

Fw

Fw

da

Da
D
D

d
d
r r

r r
D
NA49 … UU NA49 … U

Shaft dia. 120 − 140mm

Identification number Mass Boundary dimensions Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
Shaft (Ref.) mm dimensions　mm load rating load rating rotational
speed(2)
dia. With two seals With one seal With two seals With one seal (1) da Da C C0
mm g d D C B rs min Fw Min. Max. Max. N N min-1

120 NA 4924UU NA 4924U ─ ─ 2 990 120 165 45 46 1.1 135 126.5 133 158.5 178 000 410 000 1 400 LRTZ 12013546
130 NA 4926UU NA 4926U ─ ─ 4 080 130 180 50 51 1.5 150 138 148 172 206 000 511 000 1 300 LRTZ 13015051
140 NA 4928UU NA 4928U ─ ─ 4 340 140 190 50 51 1.5 160 148 158 182 214 000 549 000 1 200 LRTZ 14016051

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)　　Allowable rotational speed applies to grease lubrication.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　Bearings are provided with prepacked grease. Bearings with a seal on one side are not provided with prepacked grease. Perform
proper lubrication for use.

1N=0.102kgf=0.2248lbs.
D65 1mm=0.03937inch
D66
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Seal, Without Inner Ring, Inch Series
C

ra

Da
Fw
D
D
BR … UU

Shaft dia. 15.875 − 50.800mm

Identification number Mass Boundary dimensions　mm(inch) Standard mounting Basic dynamic Basic static Allowable
(Ref.) dimensions　mm load rating load rating rotational
speed(2)
Shaft dia.
( )
1 C C0
mm Da ras max
(inch) With two seals g Fw D C
Max. N N min-1

15.875
BR 101816 UU 54 15.875（ 5╱ 8 ） 28.575（1   1╱ 8 ） 25.400（1 ） 24.5 0.6 18 300 20 000 12 000
（ 5╱8 ）
19.050
BR 122016 UU 68 19.050（ 3╱ 4 ） 31.750（1   1╱ 4 ） 25.400（1 ） 26.5 1.0 20 700 24 400 10 000
（ 3╱4 ）
22.225
BR 142216 UU 76 22.225（ 7╱ 8 ） 34.925（1   3╱ 8 ） 25.400（1 ） 29.7 1.0 21 600 26 900 9 000
（ 7╱8 ）
25.400
BR 162416 UU 83 25.400（1 ） 38.100（1   1╱ 2 ） 25.400（1 ） 32.9 1.0 23 600 31 300 8 000
（1）
28.575
BR 182620 UU 115 28.575（1   1╱ 8 ） 41.275（1   5╱ 8 ） 31.750（1   1╱ 4 ） 36.0 1.0 34 900 49 900 7 000
（1 1╱8 ）
31.750
BR 202820 UU 124 31.750（1   1╱ 4 ） 44.450（1   3╱ 4 ） 31.750（1   1╱ 4 ） 39.2 1.0 36 000 53 500 6 500
（1 1╱4 ）
34.925
BR 223020 UU 134 34.925（1   3╱ 8） 47.625（1   7╱ 8 ） 31.750（1   1╱ 4 ） 42.4 1.0 38 500 60 000 5 500
（1 3╱8 ）
38.100
BR 243320 UU 168 38.100（1   1╱ 2 ） 52.388（2   1╱16 ） 31.750（1   1╱ 4 ） 45.1 1.5 43 700 66 900 5 500
（1 1╱2 ）
41.275
BR 263520 UU 179 41.275（1   5╱ 8 ） 55.562（2   3╱16 ） 31.750（1   1╱ 4 ） 48.3 1.5 44 800 70 900 4 500
（1 5╱8 ）
44.450
BR 283720 UU 193 44.450（1   3╱ 4 ） 58.738（2   5╱16 ） 31.750（1   1╱ 4 ） 51.5 1.5 47 500 78 200 4 500
（1 3╱4 ）
47.625
BR 303920 UU 202 47.625（1   7╱ 8 ） 61.912（2   7╱16 ） 31.750（1   1╱ 4 ） 54.7 1.5 48 500 82 100 4 000
（1 7╱8 ）
50.800
BR 324120 UU 216 50.800（2 ） 65.088（2   9╱16 ） 31.750（1   1╱ 4 ） 57.8 1.5 51 000 89 400 4 000
（2）
  
Notes(1)　　Maximum permissible corner radius of the housing
 　　 (2)　　Allowable rotational speed applies to grease lubrication.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　Bearings are provided with prepacked grease.
3.　If one side sealed type are needed, please contact .

1N=0.102kgf=0.2248lbs.
D67 1mm=0.03937inch
D68
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Seal, Without Inner Ring, Inch Series
C

ra

Da
Fw
D
D
BR … UU

Shaft dia. 57.150 − 95.250mm

Identification number Mass Boundary dimensions　mm(inch) Standard mounting Basic dynamic Basic static Allowable
(Ref.) dimensions　mm load rating load rating rotational
speed(2)
Shaft dia. ( )
1 C C0
mm Da ras max
(inch) With two seals g Fw D C
Max. N N min-1

57.150
BR 364828 UU 459 57.150（2   1╱ 4 ） 76.200（3 ） 44.450（1   3╱ 4 ） 69.0 1.5 90 300 158 000 3 500
（2 1╱4 ）
63.500
BR 405228 UU 499 63.500（2   1╱ 2 ） 82.550（3   1╱ 4 ） 44.450（1   3╱ 4 ） 74.3 2.0 94 600 174 000 3 000
（2 1╱2 ）
69.850
BR 445628 UU 540 69.850（2   3╱ 4 ） 88.900（3   1╱ 2 ） 44.450（1   3╱ 4 ） 80.7 2.0 98 700 189 000 2 500
（2 3╱4 ）
76.200
BR 486028 UU 585 76.200（3 ） 95.250（3   3╱ 4 ） 44.450（1   3╱ 4 ） 87.0 2.0 105 000 211 000 2 500
（3）
82.550
BR 526828 UU 891 82.550（3   1╱ 4 ） 107.950（4   1╱ 4 ） 44.450（1   3╱ 4 ） 99.7 2.0 109 000 227 000 2 500
（3 1╱4 ）
88.900
BR 567232 UU 1 098 88.900（3   1╱ 2 ） 114.300（4   1╱ 2 ） 50.800（2 ） 106.1 2.0 142 000 265 000 2 000
（3 1╱2 ）
95.250
BR 607632 UU 1 161 95.250（3   3╱ 4 ） 120.650（4   3╱ 4 ） 50.800（2 ） 111.4 2.5 148 000 287 000 2 000
（3 3╱4 ）

Notes(1)　　Maximum permissible corner radius of the housing

 　　 (2)　　Allowable rotational speed applies to grease lubrication.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　Bearings are provided with prepacked grease.
3.　If one side sealed type are needed, please contact .

1N=0.102kgf=0.2248lbs.
D69 1mm=0.03937inch
D70
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Seal, With Inner Ring, Inch Series
B
C

ra
ra
Fw
D

Da
d

da
D
BRI … UU

Shaft dia. 9.525 − 44.450mm

Identification number Mass Boundary dimensions　mm(inch) Standard mounting Basic dynamic Basic static Allowable Assembled inner ring
(Ref.) dimensions　mm load rating load rating rotational
speed(2)
Shaft dia.
( )
1 C C0
mm da Da ras max
(inch) With two seals g d D C B Fw
Min. Max. Max. N N min-1

9.525
BRI 61816 UU   79 9.525（ 3╱ 8 ） 28.575（1   1╱ 8 ） 25.400（1 ） 25.650 15.875（ 5╱ 8 ） 14 14.5 24.5 0.6 18 300 20 000 12 000 LRBZ 61016 B
（ 3╱8 ）
12.700
BRI 82016 UU   99 12.700（ 1╱ 2 ） 31.750（1   1╱ 4 ） 25.400（1 ） 25.650 19.050（ 3╱ 4 ） 17.5 18 26.5 0.6 20 700 24 400 10 000 LRBZ 81216 B
（ 1╱2 ）
15.875
BRI 102216 UU 113.5 15.875（ 5╱ 8 ） 34.925（1   3╱ 8 ） 25.400（1 ） 25.650 22.225（ 7╱ 8 ） 21 21.2 29.7 0.6 21 600 26 900 9 000 LRBZ 101416 B
（ 5╱8 ）
19.050
BRI 122416 UU 127 19.050（ 3╱ 4 ） 38.100（1   1╱ 2 ） 25.400（1 ） 25.650 25.400（1 ） 24 24.4 32.9 0.6 23 600 31 300 8 000 LRBZ 121616 B
（ 3╱4 ）
22.225
BRI 142620 UU 177 22.225（ 7╱ 8 ） 41.275（1   5╱ 8 ） 31.750（1   1╱ 4 ） 32.000 28.575（1   1╱ 8 ） 27 27.5 36.0 0.6 34 900 49 900 7 000 LRBZ 141820 B
（ 7╱8 ）
25.400
BRI 162820 UU 196 25.400（1 ） 44.450（1   3╱ 4 ） 31.750（1   1╱ 4 ） 32.000 31.750（1   1╱ 4 ） 30.5 30.7 39.2 0.6 36 000 53 500 6 500 LRBZ 162020 B
（1）
28.575
BRI 183020 UU 211 28.575（1   1╱ 8 ） 47.625（1   7╱ 8 ） 31.750（1   1╱ 4 ） 32.000 34.925（1   3╱ 8 ） 33.5 33.9 42.4 0.6 38 500 60 000 5 500 LRBZ 182220 B
（1 1╱8 ）
31.750
BRI 203320 UU 254 31.750（1   1╱ 4 ） 52.388（2   1╱16 ） 31.750（1   1╱ 4 ） 32.000 38.100（1   1╱ 2 ） 37 37.1 45.1 0.6 43 700 66 900 5 500 LRBZ 202420 B
（1 1╱4 ）
34.925
BRI 223520 UU 275 34.925（1   3╱ 8 ） 55.562（2   3╱16 ） 31.750（1   1╱ 4 ） 32.000 41.275（1   5╱ 8 ） 40.2 40.2 48.3 0.6 44 800 70 900 4 500 LRBZ 222620 B
（1 3╱8 ）
38.100 BRI 243720 UU 293 38.100（1   1╱ 2 ） 58.738（2   5╱16 ） 31.750（1   1╱ 4 ） 32.000 44.450（1   3╱ 4 ） 43.3 43.4 51.5 0.6 47 500 78 200 4 500 LRBZ 242820 B
（1 1╱2 ） BRI 243920 UU 362 38.100（1   1╱ 2 ） 61.912（2   7╱16 ） 31.750（1   1╱ 4 ） 32.000 47.625（1   7╱ 8 ） 43.3 45 54.7 1 48 500 82 100 4 000 LRBZ 243020 B
41.275
BRI 264120 UU 386 41.275（1   5╱ 8 ） 65.088（2   9╱16 ） 31.750（1   1╱ 4 ） 32.000 50.800（2 ） 48 49 57.8 1 51 000 89 400 4 000 LRBZ 263220 B
（1 5╱8 ）
44.450
BRI 284828 UU 804 44.450（1   3╱4 ） 76.200（3 ） 44.450（1   3╱ 4 ） 44.700 57.150（2   1╱ 4 ） 52.5 55 69.0 1.5 90 300 158 000 3 500 LRBZ 283628 B
（1 3╱4 ）

Notes(1)　　Maximum permissible corner radius of the shaft or housing

 　　 (2)　　Allowable rotational speed applies to grease lubrication.
Remarks1.　The inner ring and the outer ring each have an oil groove and an oil hole.
2.　Bearings are provided with prepacked grease.
3.　If one side sealed type are needed, please contact .

1N=0.102kgf=0.2248lbs.
D71 1mm=0.03937inch
D72
 MACHINED TYPE NEEDLE ROLLER BEARINGS
With Seal, With Inner Ring, Inch Series
B
C

ra
ra

Da
Fw
D

da
d
D
BRI … UU

Shaft dia. 50.800 − 82.550mm

Identification number Mass Boundary dimensions　mm(inch) Standard mounting dimensions Basic dynamic Basic static Allowable Assembled inner ring
(Ref.) mm load rating load rating rotational
speed(2)
Shaft dia.
da (1) C C0
mm Da ras max
(inch) With two seals g d D C B Fw
Min. Max. Max. N N min-1

50.800
BRI 325228 UU 889 50.800（2 ） 82.550（3  1╱ 4 ） 44.450（1  3╱ 4 ） 44.700 63.500（2  1╱ 2 ） 58 61 74.3 1.5 94 600 174 000 3 000 LRBZ 324028 B
（2）
57.150
BRI 365628 UU   980 57.150（2  1╱ 4 ） 88.900（3  1╱ 2 ） 44.450（1  3╱ 4 ） 44.700 69.850（2  3╱ 4 ） 65 67 80.7 1.5 98 700 189 000 2 500 LRBZ 364428 B
（2 1╱4 ）
63.500
BRI 406028 UU 1 065 63.500（2  1╱ 2 ） 95.250（3  3╱ 4 ） 44.450（1  3╱ 4 ） 44.700 76.200（3 ） 71 73 87.0 1.5 105 000 211 000 2 500 LRBZ 404828 B
（2 1╱2 ）
69.850
BRI 446828 UU 1 421 69.850（2  3╱ 4 ） 107.950（4  1╱ 4 ） 44.450（1  3╱ 4 ） 44.700 82.550（3  1╱ 4 ） 77 79 99.7 1.5 109 000 227 000 2 500 LRBZ 445228 B
（2 3╱4 ）
76.200
BRI 487232 UU 1 738 76.200（3 ） 114.300（4  1╱ 2 ） 50.800（2 ） 51.050 88.900（3  1╱ 2 ） 83.5 86 106.1 1.5 142 000 265 000 2 000 LRBZ 485632 B
（3）
82.550
BRI 527632 UU 1 851 82.550（3  1╱ 4 ） 120.650（4  3╱ 4 ） 50.800（2 ） 51.050 95.250（3  3╱ 4 ） 91 93 111.4 1.5 148 000 287 000 2 000 LRBZ 526032 B
（3 1╱4 ）

Notes(1)　　Maximum permissible corner radius of the shaft or housing

 　　 (2)　　Allowable rotational speed applies to grease lubrication.
Remarks1.　The inner ring and the outer ring each have an oil groove and an oil hole.
2.　Bearings are provided with prepacked grease.
3.　If one side sealed type are needed, please contact .

1N=0.102kgf=0.2248lbs.
D73 1mm=0.03937inch
D74
 Example of identification number ■ Oil hole
Table 2 shows the number of oil holes on the outer
Classification
Model code Dimensions symbol Model code ring.

TAF 12 19 12 P6 /SG Table 2 N

 umber of oil holes of outer ring

Type of bearing Nominal roller set bore diameter

Number of hole holes
Fw of outer ring
Roller set bore diameter mm
（12mm） Fw≦26 0
Nominal outside diameter
（19mm）
26＜Fw 1
Remark　If there is oil hole on the outer ring, care must be
D
exercised not to let oil holes within the load range.
Bearing width
（12mm）

Accuracy class
(Class 6)
■ Mounting
1 Mounting dimensions for C-Lube Machined Type
Needle Roller Bearings are shown in the table of
■ Structure and features dimensions.

C-Lube Machined Type Needle Roller Bearing is a ■ Accuracy 2 When mounting, pay special attention to avoid
locating the oil hole within the loading zone. This
bearing that is lubricated with a newly developed
C-Lube Machined Type Needle Roller Bearings are may lead to a short bearing life.
thermosetting solid-type lubricant. A large amount of
manufactured based on JIS (See page A31.). The
lubricating oil and fine particles of ultra high molecular
tolerances for the smallest single roller set bore diam-
■ Precaution for Use
weight polyolefin resin are solidified by heat treatment
eter of bearings without inner ring are based on Table
to fill the inner space of the bearing. As the bearing
14 on page A33.
rotates, the lubricating oil oozes out onto the raceway 1 Do not wash C-Lube Machined Type Needle
in proper quantities, maintaining the lubrication Roller Bearing with organic solvent and/or white

■ Fit
performance for a long period of time. kerosene, which have the ability of removing fat
C-Lube Machined Type Needle Roller Bearings are nor leave them in contact with the above agents.
bearings with a low sectional height and large load The recommended fits for C-Lube Machined Type 2 To ensure normal rotation of the C-Lube Machined
ratings. The outer ring has high rigidity and can easily Needle Roller Bearings are shown in Tables 21 to 23 Type Needle Roller Bearing, apply a load of 1% or
be used even for light alloy housings. on pages A41 and A42. over of the dynamic load rating at use.
3 The operating temperature range is -15〜+80˚C.
For continuous operation, the recommended oper-

■ Allowable Rotational Speed ating temperature is +60˚C or less.

4 When using two or more C-Lube Machined Type
■ Type
Structure of C-Lube Machined Type Needle Roller Bearing
The allowable rotational speed of C-Lube Machined Needle Roller Bearings adjacent to each other on
Type Needle Roller Bearing is affected by mounting the same shaft, it is necessary to obtain an even
C-Lube Machined Type Needle Roller Bearing is
TAF…/SG(1) and operating conditions. The reference dmn value (1) load distribution. On request, a set of bearings is
available in type shown in Table 1. is 20,000. available, in which bearings are matched to obtain
Outer ring
Table 1 Type of bearing Note(1)　dmn value = {(Bore diameter of bearing [mm] + Outside an even load distribution.
diameter of bearing [mm])/2} x rotational
Type Needle bearing with cage speed [min-1]
Further, C-Lube Machined Type Needle Roller
Cage Series Without inner ring Bearing for food machinery is also available. If need-
Metric series For light duty
■ Lubrication
TAF･･･/SG ed, please contact .

Needle roller As the internal space of C-Lube Machined Type

■ Identification number Needle Roller Bearing is filled with thermosetting
solid-type lubricant C-Lube, regreasing is not possible
The identification number of C-Lube Machined Type
due to the structure.
Needle Roller Bearing consists of model code, dimen-
sions and classification symbol. Example is shown
Note(1)　Thermosetting solid-type lubricant fills inner space of the below.
bearing.

D75 D76
 C-LUBE MACHINED TYPE NEEDLE ROLLER BEARINGS
Without Inner Ring
C C

r r

Fw

Fw
D

Da
D
r r
D
TAF … /SG TAF … /SG
Fw≦26 Fw＞26

Shaft dia. 10−45mm

Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static
(Ref.) dimension load rating load rating (Ref.) dimension load rating load rating
Shaft Shaft
dia.
Identification number Da C C0 dia.
Identification number Da C C0
g Fw D C rs min(1) Max. g Fw D C rs min(1) Max.
mm N N mm N N

10 TAF 101712/SG 11 10 17 12 0.2 15.4 5 880 5 970

29 TAF 293820/SG 59 29 38 20 0.3 36 21 600 37 200
TAF 101716/SG 14.7 10 17 16 0.2 15.4 8 230 9 190 TAF 293830/SG 88 29 38 30 0.3 36 30 900 59 100

12 TAF 121912/SG 12.5 12 19 12 0.3 17 6 610 7 260

30 TAF 304020/SG 67 30 40 20 0.3 38 25 100 40 100
TAF 121916/SG 16.8 12 19 16 0.3 17 9 250 11 200 TAF 304030/SG 101 30 40 30 0.3 38 36 000 63 900

14 TAF 142216/SG 22 14 22 16 0.3 20 11 700 13 700

35 TAF 354520/SG 76.5 35 45 20 0.3 43 26 900 46 200
TAF 142220/SG 27.5 14 22 20 0.3 20 14 800 18 600 TAF 354530/SG 116.5 35 45 30 0.3 43 38 600 73 600

15 TAF 152316/SG 23.5 15 23 16 0.3 21 12 300 14 900

40 TAF 405020/SG 86 40 50 20 0.3 48 29 400 54 100
TAF 152320/SG 29 15 23 20 0.3 21 15 600 20 200 TAF 405030/SG 130 40 50 30 0.3 48 42 300 86 200

16 TAF 162416/SG 24 16 24 16 0.3 22 12 300 15 100

45 TAF 455520/SG 95.5 45 55 20 0.3 53 31 000 60 200
TAF 162420/SG 30 16 24 20 0.3 22 15 500 20 400 TAF 455530/SG 144 45 55 30 0.3 53 44 600 95 800

18 TAF 182616/SG 26.5 18 26 16 0.3 24 13 400 17 500

TAF 182620/SG 33 18 26 20 0.3 24 17 000 23 600

19 TAF 192716/SG 28 19 27 16 0.3 25 14 000 18 700

TAF 192720/SG 35.5 19 27 20 0.3 25 17 700 25 300

20 TAF 202816/SG 28.5 20 28 16 0.3 26 13 900 18 800

TAF 202820/SG 37 20 28 20 0.3 26 17 600 25 400

21 TAF 212916/SG 30 21 29 16 0.3 27 14 400 20 000

TAF 212920/SG 37.5 21 29 20 0.3 27 18 200 27 100

22 TAF 223016/SG 31 22 30 16 0.3 28 14 900 21 200

TAF 223020/SG 39 22 30 20 0.3 28 18 900 28 700

24 TAF 243216/SG 33 24 32 16 0.3 30 15 300 22 500

TAF 243220/SG 42 24 32 20 0.3 30 19 400 30 500

25 TAF 253316/SG 35 25 33 16 0.3 31 15 800 23 700

TAF 253320/SG 43.5 25 33 20 0.3 31 20 000 32 100
Note(1)　　 Minimum allowable value of chamfer dimension r.
Remarks1.　Models with a nominal roller set bore diameter Fw of 26mm or less are provided without oil holes. other models are provided with
one oil hole and oil groove.
2.　This bearing can not be re-lubricated as thermosetting solid-type lubricant C-Lube fills inner space of the bearing.

1N=0.102kgf=0.2248lbs.
D77 1mm=0.03937inch
D78
 ■ Structure and Features Structures of Needle Roller Bearings with Separable Cage
In Needle Roller Bearings with Separable Cage,
Outer ring
the inner ring, outer ring and Needle Roller
Cage are combined, and they can be separated easi-
ly. This type has a simple structure with high accura-
Needle roller cage
cy. In addition, the radial clearance can be freely cho-
sen by selecting and combining these component
parts. As Needle Roller Cages are used, these bear-
●Needle Roller Bearings with Separable Cage - Without Inner Ring ings have excellent rotational performance.

●Needle Roller Bearings with Separable Cage - With Inner Ring

These bearings are most suitable for mass-production
high accuracy products such as machine tools, textile
D
machinery, and printing machines.

Outer ring

Needle roller cage

Outer ring

Needle roller cage

Inner ring

Outer ring

Needle roller cage

Inner ring

D79 D80
■ Types ■ Identification Number ■ Accuracy ■ Mounting
Needle Roller Bearings with Separable Cage are The identification number of Needle Roller Bearings Needle Roller Bearings with Separable Cage are Mounting examples of Needle Roller Bearings with
available in the types shown in Table 1. with Separable Cage consists of a model code, manufactured to the accuracy based on JIS (See Separable Cage are shown in Fig.1.
dimensions, any supplemental codes and a classifica- page A31.). Tolerances for the smallest single roller When mounting Needle Roller Bearings with
Table 1 Type of bearing tion symbol. The arrangement examples are as fol- set bore diameter of bearings without inner ring are Separable Cage, it is necessary to locate the needle
lows. based on Table 14 on page A33. cage axially. The needle cage is guided by shoulders
Single-row Double-row
Type of the shaft and housing or by side plates, and their
Without inner ring With inner ring Without inner ring With inner ring
guide surfaces must be heat-treated and finished by
Model code RNAF NAF RNAFW NAFW
Examples of identification number ■ Clearance grinding at right angles to the shaft central axis.

Example 1
Radial internal clearances of Needle Roller Bearings
with Separable Cage are made to the CN clearance
Dimensions related to mounting are shown in the
table of dimensions. D
Needle Roller Bearings with Separable Model code Dimensions
Supplemental
code shown in Table 18 on page A37.
Cage - Without Inner Ring
RNAF 7 14 8 N
■ Fit
The single-row as well as the double-row types are
available with the same sectional height, and either of Type of bearing
them can be selected according to load conditions.
Roller set bore diameter
Recommended fits for Needle Roller Bearings with
As shown in the section, "Design of shaft and hous-
（7mm） Separable Cage are shown in Tables 21 to 23 on
ing" on page A44, any desired radial internal clear-
pages A41 and A42.
ance can be selected by combining a shaft which is Nominal outside diameter
heat-treated and finished by grinding. （14mm）

Bearing width
（8mm）
■ Lubrication
Needle Roller Bearings with Separable Needle Roller Bearings with Separable Cage are not
Cage - With Inner Ring Cage made of synthetic resin provided with prepacked grease. Perform proper
lubrication for use. Using them without lubrication will
These bearings are made to the CN clearance shown
increase the wear of the rolling contact surfaces and
in Table 19 on page A37. When especially high accu-
shorten their lives.
racy is required, it is possible to supply semi-finished
inner rings which have a finishing allowance on their
Example 2
outside diameter so that they can be ground after
being press-fitted to shafts. Model code Dimensions
Supplemental Classification
code symbol ■ Oil Hole
NAFW 30 45 26 C2 P5 The double-row type outer rings have both an oil hole
and an oil groove, but the single-row type outer rings Fig.1 Mounting examples
Type of bearing do not. When outer rings with an oil hole are
required, attach "-OH" before the clearance symbol in
Nominal bore diameter
the identification number, and when outer rings with
（30mm）
both an oil hole and an oil groove are required, attach
Nominal outside diameter "-OG" to the same position.
（45mm） Example: NAF 203517 - OH C2 P6
When outer rings with multiple oil holes or inner rings
Bearing width
（26mm） with oil hole(s) are required, please contact .

■ Operating temperature range

Clearance symbol
(C2 clearance)

Accuracy class For synthetic resin cages, "N" is added at the end of
(Class 5) the identification number. The operating temperature
range for Needle Roller Bearings with Separable
Cage is -20 〜 +120˚C. However, the maximum allow-
able temperature for synthetic resin cages is +110˚C,
and when they are continuously operated, it is
+100˚C.

1N=0.102kgf=0.2248lbs.
D81 1mm=0.03937inch
D82
 NEEDLE ROLLER BEARINGS WITH SEPARABLE CAGE
Without Inner Ring
C C

r r

Fw
Fw

Db
D

db
Da
D
r r
D
RNAF RNAFW

Shaft dia. 5 − 18mm

Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimensions　mm load rating load rating rotational
dia. Identification number C C0 speed(2)
(1) db Da Db
mm g Fw D C rs min
Max. N N min-1

5 RNAF 5108N 2.8 5 10 8 0.2 6.7 8.4 5.4 2 420 1 950 85 000
6 RNAF 6138N 5.5 6 13 8 0.3 8.4 11 6.4 2 700 2 320 75 000
7 RNAF 7148N 6.1 7 14 8 0.3 9.4 12 7.4 2 960 2 690 65 000

8 RNAF 81510 8.2 8 15 10 0.3 10.4 13 8.4 3 630 3 600 60 000

RNAFW 81620 20.5 8 16 20 0.3 10.8 14 8.4 6 220 7 200 60 000

10 RNAF 101710 9.6 10 17 10 0.3 12.4 15 10.4 4 160 4 550 50 000

RNAF 102012 18.7 10 20 12 0.3 13.5 18 10.4 5 940 6 000 50 000
12 RNAF 122212 19.5 12 22 12 0.3 15.5 20 12.4 9 030 8 460 40 000
RNAF 142213 18.7 14 22 13 0.3 17.6 20 14.6 7 860 9 410 35 000
14 RNAFW 142220 28.5 14 22 20 0.3 17.6 20 14.6 10 800 14 200 35 000
RNAF 142612 29 14 26 12 0.3 19.4 24 14.6 9 790 9 680 35 000

15 RNAF 152313 19.7 15 23 13 0.3 18.6 21 15.6 8 250 10 200 35 000

RNAFW 152320 30.5 15 23 20 0.3 18.6 21 15.6 11 400 15 400 35 000
RNAF 162413 21 16 24 13 0.3 19.6 22 16.6 8 620 11 000 30 000
16 RNAFW 162420 32 16 24 20 0.3 19.6 22 16.6 11 900 16 700 30 000
RNAF 162812 31.5 16 28 12 0.3 21.4 26 16.6 10 500 10 900 30 000

17 RNAF 172513 22 17 25 13 0.3 20.6 23 17.6 8 980 11 800 30 000

RNAFW 172520 33.5 17 25 20 0.3 20.6 23 17.6 12 400 17 900 30 000
RNAF 182613 23 18 26 13 0.3 21.6 24 18.6 9 330 12 700 30 000
18 RNAFW 182620 35 18 26 20 0.3 21.6 24 18.6 12 900 19 100 30 000
RNAF 183012 34.5 18 30 12 0.3 23.4 28 18.6 11 800 13 100 30 000
RNAFW 183024 69.5 18 30 24 0.3 23.4 28 18.6 20 200 26 200 30 000

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)  　  Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.
Remarks1.  The character "N" at the end of the identification number indicates that a synthetic resin cage is incorporated.
2.  RNAF has no oil hole. RNAFW is provided with an oil groove and an oil hole on the outer ring.
3.  No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D83 1mm=0.03937inch
D84
 NEEDLE ROLLER BEARINGS WITH SEPARABLE CAGE
Without Inner Ring
C C

r r

Fw
Fw

Db
D

db
Da
D
r r
D
RNAF RNAFW

Shaft dia. 20 − 40mm

Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimensions　mm load rating load rating rotational
dia. Identification number C C0 speed(2)
(1) db Da Db
mm g Fw D C rs min
Max. N N min-1

RNAF 202813 25 20 28 13 0.3 23.6 26 20.6 9 590 13 500 25 000

20 RNAFW 202826 49.5 20 28 26 0.3 23.6 26 20.6 16 400 27 100 25 000
RNAF 203212 37.5 20 32 12 0.3 25.4 30 20.6 12 400 14 300 25 000
RNAFW 203224 75 20 32 24 0.3 25.4 30 20.6 21 200 28 600 25 000
RNAF 223013 27 22 30 13 0.3 25.6 28 22.6 10 200 15 200 25 000
22 RNAFW 223026 53.5 22 30 26 0.3 25.6 28 22.6 17 500 30 300 25 000
RNAF 223516 58.5 22 35 16 0.3 27.8 33 22.6 17 600 20 900 25 000
RNAFW 223532 117 22 35 32 0.3 27.8 33 22.6 30 200 41 800 25 000
RNAF 253517 51 25 35 17 0.3 29.5 33 25.6 17 300 26 600 20 000
25 RNAFW 253526 78 25 35 26 0.3 29.5 33 25.6 22 400 37 200 20 000
RNAF 253716 57 25 37 16 0.3 30.4 35 25.6 19 400 24 500 20 000
RNAFW 253732 114 25 37 32 0.3 30.4 35 25.6 33 200 49 000 20 000

28 RNAF 284016 62.5 28 40 16 0.3 33.4 38 28.6 20 100 26 500 18 000

RNAFW 284032 125 28 40 32 0.3 33.4 38 28.6 34 400 53 000 18 000
RNAF 304017 59 30 40 17 0.3 34.5 38 30.6 18 700 31 100 17 000
30 RNAFW 304026 90.5 30 40 26 0.3 34.5 38 30.6 24 200 43 400 17 000
RNAF 304216 66 30 42 16 0.3 35.4 40 30.6 20 800 28 400 17 000
RNAFW 304232 132 30 42 32 0.3 35.4 40 30.6 35 700 56 800 17 000
RNAF 354517 67.5 35 45 17 0.3 39.5 43 35.6 20 500 36 900 14 000
35 RNAFW 354526 103 35 45 26 0.3 39.5 43 35.6 26 600 51 500 14 000
RNAF 354716 75.5 35 47 16 0.3 40.4 45 35.6 23 100 33 900 14 000
RNAFW 354732 151 35 47 32 0.3 40.4 45 35.6 39 500 67 800 14 000
RNAF 405017 76 40 50 17 0.3 43.5 48 40.8 22 200 42 700 12 000
RNAFW 405034 152 40 50 34 0.3 43.5 48 40.8 38 000 85 400 12 000
40
RNAF 405520 140 40 55 20 0.3 45.2 53 40.8 31 400 48 000 12 000
RNAFW 405540 280 40 55 40 0.3 45.2 53 40.8 53 900 96 000 12 000

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)  　  Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.
Remarks1.  RNAF has no oil hole. RNAFW is provided with an oil groove and an oil hole on the outer ring.
2.  No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D85 1mm=0.03937inch
D86
 NEEDLE ROLLER BEARINGS WITH SEPARABLE CAGE
Without Inner Ring
C C

r r

Fw
Fw

Db
D

db
Da
D
r r
D
RNAF RNAFW

Shaft dia. 45 − 100mm

Mass Boundary dimensions　mm Standard mounting Basic dynamic Basic static Allowable
Shaft (Ref.) dimensions　mm load rating load rating rotational
dia. Identification number C C0 speed(2)
(1) db Da Db
mm g Fw D C rs min
Max. N N min-1

RNAF 455517 83.5 45 55 17 0.3 48.5 53   45.8 23 300 47 100 11 000

45 RNAFW 455534 167 45 55 34 0.3 48.5 53   45.8 39 900 94 200 11 000
RNAF 456220 184 45 62 20 0.3 50.9 60   45.8 33 200 53 300 11 000
RNAFW 456240 370 45 62 40 0.3 50.9 60   45.8 56 900 107 000 11 000
RNAF 506220 138 50 62 20 0.3 54.2 60   50.8 27 100 59 300 10 000
50 RNAFW 506240 275 50 62 40 0.3 54.2 60   50.8 46 400 119 000 10 000
RNAF 506520 170 50 65 20 0.3 55.2 63   50.8 35 900 61 100 10 000
RNAFW 506540 340 50 65 40 0.6 55.2 61   50.8 61 500 122 000 10 000
RNAF 556820 167 55 68 20 0.3 59.5 66   55.8 28 600 66 000 9 000
55 RNAFW 556840 335 55 68 40 0.3 59.5 66   55.8 49 000 132 000 9 000
RNAF 557220 220 55 72 20 1 60.9 67   55.8 37 400 66 400 9 000
RNAFW 557240 440 55 72 40 1 60.9 67   55.8 64 100 133 000 9 000

60 RNAF 607820 255 60 78 20 1 66.3 73   60.8 38 900 71 700 8 500

RNAFW 607840 510 60 78 40 1 66.3 73   60.8 66 700 143 000 8 500

65 RNAF 658530 470 65 85 30 1.5 72 77   66 59 300 127 000 7 500

RNAFW 658560 945 65 85 60 1.5 72 77   66 102 000 255 000 7 500

70 RNAF 709030 500 70 90 30 1.5 77 82   71 61 200 136 000 7 000

RNAFW 709060 1 000 70 90 60 1.5 77 82   71 105 000 272 000 7 000

75 RNAF 759530 530 75 95 30 1.5 82 87   76 63 100 144 000 6 500

RNAFW 759560 1 060 75 95 60 1.5 82 87   76 108 000 289 000 6 500

80 RNAF 8010030 560 80 100 30 1.5 87 92   81 65 000 153 000 6 000
RNAFW 8010060 1 120 80 100 60 1.5 87 92   81 111 000 306 000 6 000
85 RNAF 8510530 590 85 105 30 1.5 92 97   86 66 600 161 000 6 000
90 RNAF 9011030 625 90 110 30 1.5 97 102   91 69 600 174 000 5 500
95 RNAF 9511530 655 95 115 30 1.5 102 107   96 70 900 182 000 5 500
100 RNAF 10012030 685 100 120 30 1.5 107 112 101 72 500 191 000 4 500
Notes(1)　　Minimum allowable value of chamfer dimension r
 　　 (2)  　  Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.
Remarks1.  RNAF has no oil hole. RNAFW is provided with an oil groove and an oil hole on the outer ring.
2.  No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D87 1mm=0.03937inch
D88
 NEEDLE ROLLER BEARINGS WITH SEPARABLE CAGE
With Inner Ring
C C

r r

r r

Fw
Fw

Db
D

da
Da
D

db
d

d
r r

r r
D
NAF NAFW

Shaft dia. 6 − 25mm

Mass Boundary dimensions　mm Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft (Ref.) load rating load rating rotational inner ring
dia. Identification number C C speed(2)
(1) db Da da Db 0

mm g d D C rs min Fw
Max. Min. Max. N N min-1

6 NAF 61710 13.5 6 17 10 0.3 10 12.4 15 8   9.7 10.4 4 160 4 550 50 000 LRT 61010
7 NAF 72012 22.5 7 20 12 0.3 10 13.5 18 9   9.7 10.4 5 940 6 000 50 000 LRT 71012-1
9 NAF 92212 24 9 22 12 0.3 12 15.5 20 11 11.5 12.4 9 030 8 460 40 000 LRT 91212
NAF 102213 26 10 22 13 0.3 14 17.6 20 12 13 14.6 7 860 9 410 35 000 LRT 101413
10 NAFW 102220 40 10 22 20 0.3 14 17.6 20 12 13 14.6 10 800 14 200 35 000 LRT 101420
NAF 102612 36 10 26 12 0.3 14 19.4 24 12 13 14.6 9 790 9 680 35 000 LRT 101412
NAF 122413 29.5 12 24 13 0.3 16 19.6 22 14 15 16.6 8 620 11 000 30 000 LRT 121613
12 NAFW 122420 45.5 12 24 20 0.3 16 19.6 22 14 15 16.6 11 900 16 700 30 000 LRT 121620
NAF 122812 40 12 28 12 0.3 16 21.4 26 14 15 16.6 10 500 10 900 30 000 LRT 121612
NAF 152813 38.5 15 28 13 0.3 20 23.6 26 17 19 20.6 9 590 13 500 25 000 LRT 152013
15 NAFW 152826 77.5 15 28 26 0.3 20 23.6 26 17 19 20.6 16 400 27 100 25 000 LRT 152026
NAF 153212 50.5 15 32 12 0.3 20 25.4 30 17 19 20.6 12 400 14 300 25 000 LRT 152012
NAF 173013 42.5 17 30 13 0.3 22 25.6 28 19 21 22.6 10 200 15 200 25 000 LRT 172213
17 NAFW 173026 84.5 17 30 26 0.3 22 25.6 28 19 21 22.6 17 500 30 300 25 000 LRT 172226
NAF 173516 77.5 17 35 16 0.3 22 27.8 33 19 21 22.6 17 600 20 900 25 000 LRT 172216
NAFW 173532 155 17 35 32 0.3 22 27.8 33 19 21 22.6 30 200 41 800 25 000 LRT 172232
NAF 203517 74 20 35 17 0.3 25 29.5 33 22 24 25.6 17 300 26 600 20 000 LRT 202517
20 NAFW 203526 114 20 35 26 0.3 25 29.5 33 22 24 25.6 22 400 37 200 20 000 LRT 202526
NAF 203716 79 20 37 16 0.3 25 30.4 35 22 24 25.6 19 400 24 500 20 000 LRT 202516
NAFW 203732 158 20 37 32 0.3 25 30.4 35 22 24 25.6 33 200 49 000 20 000 LRT 202532
NAF 254017 87.5 25 40 17 0.3 30 34.5 38 27 29 30.6 18 700 31 100 17 000 LRT 253017
NAFW 254026 135 25 40 26 0.3 30 34.5 38 27 29 30.6 24 200 43 400 17 000 LRT 253026
25
NAF 254216 94 25 42 16 0.3 30 35.4 40 27 29 30.6 20 800 28 400 17 000 LRT 253016
NAFW 254232 186 25 42 32 0.3 30 35.4 40 27 29 30.6 35 700 56 800 17 000 LRT 253032

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)  　  Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.
Remarks1.  NAF has no oil hole. NAFW is provided with an oil groove and an oil hole on the outer ring.
2.  No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D89 1mm=0.03937inch
D90
 NEEDLE ROLLER BEARINGS WITH SEPARABLE CAGE
With Inner Ring
C C

r r

r r

Fw
Fw

Db
D

da
Da
D

db
d

d
r r

r r
D
NAF NAFW

Shaft dia. 30 − 65mm

Mass Boundary dimensions　mm Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft (Ref.) load rating load rating rotational inner ring
dia. Identification number C C speed(2)
0
(1) db Da da Db
mm g d D C rs min Fw
Max. Min. Max. N N min-1

NAF 304517 101 30 45 17 0.3 35 39.5 43 32 34 35.6 20 500 36 900 14 000 LRT 303517
30 NAFW 304526 155 30 45 26 0.3 35 39.5 43 32 34 35.6 26 600 51 500 14 000 LRT 303526
NAF 304716 107 30 47 16 0.3 35 40.4 45 32 34 35.6 23 100 33 900 14 000 LRT 303516
NAFW 304732 215 30 47 32 0.3 35 40.4 45 32 34 35.6 39 500 67 800 14 000 LRT 303532
NAF 355017 115 35 50 17 0.3 40 43.5 48 37 39 40.8 22 200 42 700 12 000 LRT 354017
35 NAFW 355034 230 35 50 34 0.3 40 43.5 48 37 39 40.8 38 000 85 400 12 000 LRT 354034
NAF 355520 186 35 55 20 0.3 40 45.2 53 37 39 40.8 31 400 48 000 12 000 LRT 354020
NAFW 355540 375 35 55 40 0.3 40 45.2 53 37 39 40.8 53 900 96 000 12 000 LRT 354040
NAF 405517 128 40 55 17 0.3 45 48.5 53 42 44 45.8 23 300 47 100 11 000 LRT 404517
40 NAFW 405534 255 40 55 34 0.3 45 48.5 53 42 44 45.8 39 900 94 200 11 000 LRT 404534
NAF 406220 235 40 62 20 0.3 45 50.9 60 42 44 45.8 33 200 53 300 11 000 LRT 404520
NAFW 406240 475 40 62 40 0.3 45 50.9 60 42 44 45.8 56 900 107 000 11 000 LRT 404540
NAF 456220 196 45 62 20 0.3 50 54.2 60 47 49 50.8 27 100 59 300 10 000 LRT 455020
45 NAFW 456240 390 45 62 40 0.3 50 54.2 60 47 49 50.8 46 400 119 000 10 000 LRT 455040
NAF 457220 340 45 72 20 1 55 60.9 67 50 54 55.8 37 400 66 400 9 000 LRT 455520
NAFW 457240 685 45 72 40 1 55 60.9 67 50 54 55.8 64 100 133 000 9 000 LRT 455540
NAF 506820 230 50 68 20 0.3 55 59.5 66 52 54 55.8 28 600 66 000 9 000 LRT 505520
50 NAFW 506840 465 50 68 40 0.3 55 59.5 66 52 54 55.8 49 000 132 000 9 000 LRT 505540
NAF 507820 390 50 78 20 1 60 66.3 73 55 59 60.8 38 900 71 700 8 500 LRT 506020
NAFW 507840 775 50 78 40 1 60 66.3 73 55 59 60.8 66 700 143 000 8 500 LRT 506040

55 NAF 558530 690 55 85 30 1.5 65 72 77 63 63.5 66 59 300 127 000 7 500 LRT 556530
NAFW 558560 1 380 55 85 60 1.5 65 72 77 63 63.5 66 102 000 255 000 7 500 LRT 556560

60 NAF 609030 740 60 90 30 1.5 70 77 82 68 68.5 71 61 200 136 000 7 000 LRT 607030
NAFW 609060 1 480 60 90 60 1.5 70 77 82 68 68.5 71 105 000 272 000 7 000 LRT 607060
NAF 659530 790 65 95 30 1.5 75 82 87 73 73.5 76 63 100 144 000 6 500 LRT 657530
65
NAFW 659560 1 580 65 95 60 1.5 75 82 87 73 73.5 76 108 000 289 000 6 500 LRT 657560
Notes(1)　　Minimum allowable value of chamfer dimension r
 　　 (2)  　  Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.
Remarks1.  NAF has no oil hole. NAFW is provided with an oil groove and an oil hole on the outer ring.
2.  No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D91 1mm=0.03937inch
D92
 NEEDLE ROLLER BEARINGS WITH SEPARABLE CAGE
With Inner Ring
C C

r r

r r

Fw
Fw

Db
D

da
Da
D

db
d

d
r r

r r
D
NAF NAFW

Shaft dia. 70 − 90mm

Mass Boundary dimensions　mm Standard mounting dimensions　mm Basic dynamic Basic static Allowable Assembled
Shaft (Ref.) load rating load rating rotational inner ring
dia. Identification number C C speed(2)
0
(1) db Da da Db
mm g d D C rs min Fw
Max. Min. Max. N N min-1

70 NAF 7010030 835 70 100 30 1.5 80 87 92 78 78.5 81 65 000 153 000 6 000 LRT 708030-1
NAFW 7010060 1 680 70 100 60 1.5 80 87 92 78 78.5 81 111 000 306 000 6 000 LRT 708060
75 NAF 7510530 885 75 105 30 1.5 85 92 97 83 83.5 86 66 600 161 000 6 000 LRT 758530-1
80 NAF 8011030 935 80 110 30 1.5 90 97 102 88 88.5 91 69 600 174 000 5 500 LRT 809030-1
85 NAF 8511530 985 85 115 30 1.5 95 102 107 93 93.5 96 70 900 182 000 5 500 LRT 859530
90 NAF 9012030 1 040 90 120 30 1.5 100 107 112 98 98.5 101 72 500 191 000 4 500 LRT 9010030

Notes(1)　　Minimum allowable value of chamfer dimension r

 　　 (2)  　  Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 50% of this value is allowable.
Remarks1.  NAF has no oil hole. NAFW is provided with an oil groove and an oil hole on the outer ring.
2.  No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
D93 1mm=0.03937inch
D94
 ■ Structure and Features Structures of Roller Bearings
Roller Bearings in which rollers are incorporated
in two rows are non-separable heavy-duty bearings. Outer ring

They can withstand not only radial loads but axial Roller
loads as well, which are supported at the contacts
Stepped spring
●Caged Roller Bearings between the shoulders of inner and outer rings and
Side plate for
the end faces of rollers. Therefore, they are most
●Full Complement Roller Bearings
inner ring
suitable for use at the fixing side of a shaft. Like nee-
dle roller bearings, they are also compact.
●Roller Bearings for Sheaves
Inner ring
Roller bearings include the caged type, full comple-
ment type and the type for sheaves, and any bearings
suitable for the operating conditions can be selected. Cage
In particular, these bearings are used for heavy-duty
machines such as construction machinery, and indus-
trial machinery.
Outer ring

Roller
E
Stepped spring
Side plate for
inner ring

Inner ring

Outer ring

Roller

Side plate for

inner ring

Inner ring

Seal

Outer ring

Roller

Inner ring

Shield

Stop ring

E1 E2
■ Types ■ Identification Number ■ Accuracy ■ Lubrication
The types of Roller Bearings shown in Table 1 are The identification number of Roller Bearings consists Roller Bearings are manufactured in accordance with Bearings with prepacked grease are shown in Table
available. of a model code, dimensions, any supplemental JIS (See page A31.). A side plate for inner ring is 3. For Caged Roller Bearings and Full Complement
codes and a classification symbol. The arrangement assembled on one side of caged or full complement Roller Bearings, ALVANIA GREASE S2 (SHOWA
Table 1 Type of bearing examples are shown below. roller bearings. The tolerance of bore diameter of the SHELL SEKIYU K.K.) is prepacked as the lubricating
Type side plate is shown below. Tolerances of Roller grease. For Roller Bearings for Sheaves, ALVANIA
Full
Bearings for Sheaves represent the values before GREASE EP2 (SHOWA SHELL SEKIYU K.K.) is
Caged type complement For sheaves Examples of identification number
type surface treatment. The tolerance of internal distance prepacked as the lubricating grease.
Series
between cir-clips is shown below. In the case of bearings without prepacked grease,
NAU49 Example 1
Standard NAG49 ── Tolerance of bore diameter of the side plate d: E7 perform proper lubrication for use. Operating without
TRU Supplemental Classification
Model code Dimensions code symbol Tolerance of internal distance between cir-clips C1: 0〜 lubrication will increase the wear of the rolling contact
NAU49 … UU +0.4mm surfaces and shorten their lirees.
With seal
TRU … UU
NAG49 … UU NAS50 … UUNR NAG 49 10 UU P6
■ Clearance ■ Oil Hole
NAS50 … ZZNR
E
With shield ── ── Type of bearing
Roller Bearings are manufactured to the CN clear- The number of oil holes of the inner and outer rings is
Dimension series
ance shown in Table 18 on page A37. However, shown in Table 4.
Caged Roller Bearings  Roller Bearings for Sheaves are manufactured so that
■ Operating Temperature Range
Bore diameter number
proper operating clearances are obtained after being
These bearings are suitable for high-speed rotations
Seal symbol (With seals on both sides) mounted with a specified fit.
and fluctuating loads. Also, as the axial distance The operating temperature range for Roller Bearings
between the double-row rollers is comparatively large,
large moment loads can be supported.
Accuracy class
(Class 6)
■ Fit is −20℃〜＋120℃. However, the maximum allow-
able temperature for Roller Bearings for Sheaves is
Caged roller bearings with seal incorporate seals on The recommended fits for Roller Bearings are shown ＋110℃.
both sides. Synthetic resin rubber seals are excellent in Tables 21 to 22 on pages A41 and A42. The rec-
in the prevention of dust penetration and grease leak- ommended fits for Roller Bearings for Sheaves are
age, providing an excellent sealing effect. Example 2 shown in Table 2.
Supplemental
Model code Dimensions code Table 2 Recommended fits for Roller Bearings for Sheaves
Full Complement Roller Bearings NAS 50 10 ZZ NR Tolerance class of shaft Tolerance class of housing bore
These bearings are suitable for low-speed rotations or
Type of bearing g6 N7
oscillating motions and heavy loads. Similar to the
caged type, the structure is advantageous for support- Dimension series
ing moment loads. Table 3 Bearings with prepacked grease 〇：With prepacked grease　×：Without prepacked grease
The bearings with seal incorporate seals on both Bore diameter number
Type Standard With seals With shields
sides.
Shield symbol
(With shields on both sides) Caged type NAU ，TRU × 〇 −
Roller Bearings for Sheaves Bearing ring shape symbol
Full complement type NAG × 〇 −
(With stop rings on outer ring) For sheaves NAS − 〇 〇
These bearings are the double-row full complement
type with a low sectional height designed for use in
Table 4 Number of oil holes of the inner ring and outer ring
sheaves. There are two types; the sealed type and
the shield type. They can withstand heavy radial 　　　　　　　　Type Number of oil holes of the outer ring Number of oil holes
loads and shock loads at comparatively low-speed Nominal bore diameter d mm Standard With seals With shields of the inner ring

rotations, and can also withstand axial loads. d ≦ 17 0 0

NAU ─ 0
They can easily be fixed axially to sheaves using the Caged type   17 ＜ d 2 2
stop rings of the outer ring. As the width of the inner ─
TRU 2 2 0
ring is designed to be larger than that of the outer
d ≦ 17 0 0
ring, they require no spacer between sheaves. The Full complement type NAG ─ 0
structure is stable because the double-row rollers can   17 ＜ d 2 2
withstand the moment loads caused by rope transi- For sheaves NAS ─ 0 0 2
tion. Remark　The bearings with oil holes are also provided with an oil groove.
The surfaces of these bearings are treated to have
high corrosion resistance.

1N=0.102kgf=0.2248lbs.
E3 1mm=0.03937inch
E4
■ Axial Load Capacity Calculation example
dmn fv
■ Mounting
Axial load capacity is not determined from the basic When a roller bearing for sheaves NAS 5016 ZZ NR 300000 0.20 Unlike needle roller bearings, Caged and Full
dynamic load rating based on rolling fatigue, but is is run at n = 250 min-1 under grease lubrication and Complement Roller Bearings are non-separable.
200000 0.30 0
determined by the amount of heat generated by slid- subjected to an intermittent axial load, the axial load As shown in Fig. 3 (1), the inner ring should be press-
ing contact between the ends of rollers and guide 0.30 fitted until it makes close contact with the shaft shoul-
capacity is calculated as follows. 0.40
shoulders of the inner and outer rings. It is therefore As the bearing bore diameter is 80 mm, fA = 18000 is 100000 der, and fixed axially with a nut. Dimensions of the
0.60
limited by the load conditions, sliding speeds, lubrica- obtained from the axial load capacity line of Fig. 1 (ii). shoulders of the shaft and housing should be based
0.70
tion methods, etc. a＝1 50000 on J and E W shown in the table of dimensions,
The axial load capacity of Roller Bearings is obtained   80 ＋ 125　 0.80 respectively.
from the following equation. dm ≒ ＝ 102.5 In the case of Roller Bearings for Sheaves, as shown
2
If the axial load increases in comparison with the radi- in Fig. 3 (2), the outer ring should be fixed by stop
dmn ＝ 102.5 x 250 ≒ 25600 0.90
al load, it will start to interfere with the smooth rolling rings after being press-fitted into the sheaves, and the
From Fig. 2, fv ≒ 0.87
motion. The axial load should therefore be within inner ring should be fixed securely in the axial direc-
Therefore, the axial load capacity CA is obtained. 10000 0.95
20% of the radial load. tion.

　　　CA＝fv a fA  ……………………………………(1)
CA ＝ fv a fA ＝ 0.87×1×18000 ≒ 15700 N
5000
E
　where, 　CA：Axial load capacity 　N 0.98
　   fv：Speed correction factor
800000
fv is obtained from Fig.2 by calculat-
600000
ing the dmn value.
400000
dmn ＝ dm×n 1000 1.0
Grease lubrication
                    dm：M ean value of bearing bore
200000 Oil lubrication
and outside diameters　mm

　　 （　　　     2
d ≒
d＋D
m ） 100000
80000
Fig. 2 Speed correction factor
(1)
                        n ：Rotational speed　min-1
60000
                            When dmn ≦ 1000, fv ＝ 1.
40000
                        a：Value determined by type of bearing
(See Table 5. )
                   fA：Axial load capacity factor (See Fig.1.) 20000

10000
Table 5 Value by type of bearing 8000
6000
Type of bearing a
4000
NAS 50 1
NAG 49 0.78 2000
(2)
NAU 49，TRU 0.7
1000 Fig. 3 Mounting examples
800
600

400

200

100
10 20 40 60 80 100 200 400

Fig. 1 Axial load capacity factor

1N=0.102kgf=0.2248lbs.
E5 1mm=0.03937inch
E6
 ROLLER BEARINGS
Caged Roller Bearings C C C
C
Full Complement Roller Bearings
r r r
r

r r r
r

d E7
d E7
Ew
Ew

Ew
D
D
D

J
J

d
d
D
Ew

J
d
r r
r
r
r r r
r

NAG49 NAU49 NAG49 NAU49 TRU

（d ≦ 17） （d ≦ 17）
Shaft dia. 10 − 35mm E
Identification number Mass Boundary dimensions Basic dynamic Basic static Allowable
(Ref.) mm load rating load rating rotational
speed(2)
Shaft Full complement Caged type (1) C C0
dia.
mm
type
g d D C rs min J Ew
N N min-1

10 NAG 4900 ─ ─ 25.5 10 22 13 0.3 15.5 18.5 9 650 10 800 17 000

─ NAU 4900 ─ 24.5 10 22 13 0.3 15.5 18.5 6 580 6 470 30 000

12 NAG 4901 ─ ─ 28.5 12 24 13 0.3 17 20 10 300 12 000 15 000

─ NAU 4901 ─ 27.5 12 24 13 0.3 17 20 6 950 7 120 25 000
NAG 4902 ─ ─ 38 15 28 13 0.3 21 24 11 800 15 200 12 000
15 ─ NAU 4902 ─ 36.5 15 28 13 0.3 21 24 7 950 9 020 20 000
─ ─ TRU 153320 80.5 15 33 20 0.3 19.5 27 10 400 10 400 20 000
NAG 4903 ─ ─ 41 17 30 13 0.3 22.5 25.5 12 300 16 500 11 000
17 ─ NAU 4903 ─ 39.5 17 30 13 0.3 22.5 25.5 8 240 9 670 19 000
─ ─ TRU 173425 100 17 34 25 0.3 21.5 29.5 18 000 21 600 18 000
NAG 4904 ─ ─ 76.5 20 37 17 0.3 24 31.5 15 600 18 900 9 500
20 ─ NAU 4904 ─ 76 20 37 17 0.3 24 31.5 10 700 11 300 16 000
─ ─ TRU 203820 96.5 20 38 20 0.3 25 32.5 12 100 13 400 16 000
─ ─ TRU 203825 122 20 38 25 0.3 25 32.5 18 700 23 600 16 000
NAG 4905 ─ ─ 89.5 25 42 17 0.3 29.5 37 17 500 23 200 7 500
25 ─ NAU 4905 ─ 89 25 42 17 0.3 29.5 37 11 900 13 900 13 000
─ ─ TRU 254425 154 25 44 25 0.3 30.5 38 21 000 28 900 13 000
28 ─ ─ TRU 284530 173 28 45 30 0.3 31.5 39.5 28 700 43 800 12 000
NAG 4906 ─ ─ 103 30 47 17 0.3 34 41.5 19 400 27 600 6 500
30 ─ NAU 4906 ─ 102 30 47 17 0.3 34 41.5 13 000 16 200 12 000
─ ─ TRU 304830 197 30 48 30 0.3 35 42.5 29 400 46 600 11 000
32 ─ ─ TRU 325230 260 32 52 30 0.6 38 46 29 800 44 200 10 000
NAG 4907 ─ ─ 172 35 55 20 0.6 40 49 28 700 43 800 5 500
35 ─ NAU 4907 ─ 168 35 55 20 0.6 40 49 19 500 26 300 10 000
─ ─ TRU 355630 270 35 56 30 0.6 40 49 32 200 49 800 10 000

Notes(1)　　Minimum allowable value of chamfer dimension r

(2)   　 Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Considering that the axial load acts under practical operating conditions, up to 1/10 of this value is recommended for actual use.
Remarks1.　The NAG and NAU series with a bore diameter d of 17 mm or less have no oil hole. In others, the outer ring has an oil groove and
two oil holes.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
E7 1mm=0.03937inch
E8
 ROLLER BEARINGS
Caged Roller Bearings C C

Full Complement Roller Bearings

r r

r r

d E7
d E7
Ew

Ew
D
D

J
d
r r

r r

NAG49 NAU49 TRU

Shaft dia. 40 − 80mm E

Identification number Mass Boundary dimensions Basic dynamic Basic static Allowable
(Ref.) mm load rating load rating rotational
speed(2)
Shaft Full complement Caged type (1) C C0
dia.
mm
type
g d D C rs min J Ew
N N min-1

NAG 4908 ─ ─ 225 40 62 22 0.6 46 56 34 600 49 500 5 000

40 ─ ─ TRU 405930 265 40 59 30 0.6 45 52.5 34 700 62 500 8 500
─ NAU 4908 ─ 220 40 62 22 0.6 46 56 23 400 29 400 8 500
42 ─ ─ TRU 426230 290 42 62 30 0.6 48 56.5 34 600 57 800 8 000
NAG 4909 ─ ─ 265 45 68 22 0.6 51 61 36 400 54 700 4 500
45 ─ ─ TRU 456430 295 45 64 30 0.6 50.5 58.5 32 600 59 700 8 000
─ NAU 4909 ─ 260 45 68 22 0.6 51 61 24 800 32 800 8 000
NAG 4910 ─ ─ 270 50 72 22 0.6 55.5 65.5 38 200 59 900 4 000
50 ─ NAU 4910 ─ 265 50 72 22 0.6 55.5 65.5 26 200 36 200 7 000
─ ─ TRU 507745 710 50 77 45 1 58 69 75 700 134 000 7 000
NAG 4911 ─ ─ 395 55 80 25 1 61.5 72.5 48 100 77 700 3 500
55 ─ NAU 4911 ─ 385 55 80 25 1 61.5 72.5 33 000 47 000 6 500
─ ─ TRU 558138 615 55 81 38 1 61.5 72.5 61 400 104 000 6 500
NAG 4912 ─ ─ 425 60 85 25 1 67 77.5 50 300 84 300 3 500
60 ─ NAU 4912 ─ 415 60 85 25 1 67 77.5 34 700 51 400 6 000
─ ─ TRU 608945 880 60 89 45 1 69.5 81.5 88 100 152 000 6 000

65 NAG 4913 ─ ─ 455 65 90 25 1 72 83 53 200 93 000 3 000

─ NAU 4913 ─ 440 65 90 25 1 72 83 36 900 57 100 5 500

70 NAG 4914 ─ ─ 725 70 100 30 1 79 91.5 77 700 139 000 3 000

─ NAU 4914 ─ 705 70 100 30 1 79 91.5 53 700 84 600 5 000
NAG 4915 ─ ─ 775 75 105 30 1 83.5 95.5 80 000 146 000 2 500
75 ─ NAU 4915 ─ 750 75 105 30 1 83.5 95.5 54 800 88 200 5 000
─ ─ TRU 7510845 1 240 75 108 45 1 85.5 98.5 103 000 190 000 4 500
NAG 4916 ─ ─ 815 80 110 30 1 89.5 102 83 000 157 000 2 500
80
─ NAU 4916 ─ 790 80 110 30 1 89.5 102 57 200 95 500 4 500

Notes(1)　　Minimum allowable value of chamfer dimension r

(2)  　  Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Considering that the axial load acts under practical operating conditions, up to 1/10 of this value is recommended for actual use.
Remarks1.　The outer ring has an oil groove and two oil holes.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
E9 1mm=0.03937inch
E10
 ROLLER BEARINGS
Caged Roller Bearings C C

Full Complement Roller Bearings

r r

r r

d E7
d E7
Ew

Ew
D
D

J
d
r r

r r

NAG49 NAU49 TRU

Shaft dia. 85 − 140mm E

Identification number Mass Boundary dimensions Basic dynamic Basic static Allowable
(Ref.) mm load rating load rating rotational
speed(2)
Shaft Full complement Caged type (1) C C0
dia.
mm
type
g d D C rs min J Ew
N N min-1

NAG 4917 ─ ─ 1 190 85 120 35 1.5 96 110 111 000 200 000 2 500
─ ─ TRU 8511850 1 530 85 118 50 1 94.5 107.5 114 000 222 000 4 000
85
─ NAU 4917 ─ 1 150 85 120 35 1.5 96 110 75 400 120 000 4 000
─ ─ TRU 8512045 1 500 85 120 45 1.5 96.5 110 110 000 215 000 4 000
NAG 4918 ─ ─ 1 250 90 125 35 1.5 101 115.5 114 000 211 000 2 500
90 ─ NAU 4918 ─ 1 210 90 125 35 1.5 1 01 115.5 79 500 130 000 4 000
─ ─ TRU 9012550 1 740 90 125 50 1.5 1 01 114 119 000 240 000 4 000
NAG 4919 ─ ─ 1 300 95 130 35 1.5 106 120.5 117 000 222 000 2 000
95
─ NAU 4919 ─ 1 270 95 130 35 1.5 1 06 120.5 81 000 136 000 4 000
NAG 4920 ─ ─ 1 850 100 140 40 1.5 114.5 129.5 152 000 292 000 2 000
100 ─ ─ TRU 10013550 1 900 100 135 50 1.5 1 12 125.5 124 000 264 000 3 500
─ NAU 4920 ─ 1 770 100 140 40 1.5 1 14.5 129.5 106 000 181 000 3 500
105 ─ ─ TRU 10515350 2 890 105 153 50 1.5 120 138 159 000 286 000 3 500
NAG 4922 ─ ─ 2 010 110 150 40 1.5 123 138.5 161 000 322 000 1 900
110
─ NAU 4922 ─ 1 930 110 150 40 1.5 1 23 138.5 113 000 200 000 3 500
NAG 4924 ─ ─ 2 780 120 165 45 1.5 136 153.5 208 000 431 000 1 700
120
─ NAU 4924 ─ 2 680 120 165 45 1.5 1 36 153.5 146 000 268 000 3 000
125 ─ ─ TRU 12517860 4 490 125 178 60 1.5 143.5 162 211 000 408 000 3 000
NAG 4926 ─ ─ 3 750 130 180 50 2 147 165.5 240 000 495 000 1 600
130
─ NAU 4926 ─ 3 610 130 180 50 2 147 165.5 166 000 304 000 2 500
135 ─ ─ TRU 13518860 4 790 135 188 60 1.5 154 172.5 220 000 442 000 2 500
NAG 4928 ─ ─ 3 990 140 190 50 2 157.5 176 249 000 531 000 1 500
140
─ NAU 4928 ─ 3 840 140 190 50 2 157.5 176 174 000 327 000 2 500

Notes(1)　　Minimum allowable value of chamfer dimension r

(2)  　  Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Considering that the axial load acts under practical operating conditions, up to 1/10 of this value is recommended for actual use.
Remarks1.　The outer ring has an oil groove and two oil holes.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
E11 1mm=0.03937inch
E12
 ROLLER BEARINGS
Caged Roller Bearings With Seal C C C

Full Complement Roller Bearings With Seal

r r r

r r r

d E7

d E7
Ew
Ew

Ew
D
D

D
J

d
d

J
d
r r r

r r r

NAG49 … UU NAG49 … UU NAU49 … UU

（d ≦ 17） TRU … UU
Shaft dia. 10 − 40mm E
Identification number Mass Boundary dimensions　 Basic dynamic Basic static Allowable
(Ref.) mm load rating load rating rotational
speed(2)
Shaft Full complement Caged type (1) C C0
dia.
mm
type
g d D C r s min J Ew
N N min-1

10 NAG 4900UU ─ ─ 25.5 10 22 13 0.3 15.5 19.5 9 650 10 800 10 000

12 NAG 4901UU ─ ─ 28.5 12 24 13 0.3 17 21 10 300 12 000 9 000

15 NAG 4902UU ─ ─ 38 15 28 13 0.3 21 25 11 800 15 200 7 000

─ ─ TRU 153320UU 80.5 15 33 20 0.3 19.5 27 10 400 10 400 9 500

17 NAG 4903UU ─ ─ 41 17 30 13 0.3 22.5 26.5 12 300 16 500 6 500

─ ─ TRU 173425UU 100 17 34 25 0.3 21.5 29.5 18 000 21 600 8 500
NAG 4904UU ─ ─ 76.5 20 37 17 0.3 24 31.5 15 600 18 900 5 500
20 ─ NAU 4904UU ─ 76 20 37 17 0.3 24 31.5 10 700 11 300 8 000
─ ─ TRU 203820UU 96.5 20 38 20 0.3 25 32.5 12 100 13 400 7 500
─ ─ TRU 203825UU 122 20 38 25 0.3 25 32.5 18 700 23 600 7 500
NAG 4905UU ─ ─ 89.5 25 42 17 0.3 29.5 37 17 500 23 200 4 500
25 ─ NAU 4905UU ─ 89 25 42 17 0.3 29.5 37 11 900 13 900 6 500
─ ─ TRU 254425UU 154 25 44 25 0.3 30.5 38 21 000 28 900 6 000
28 ─ ─ TRU 284530UU 173 28 45 30 0.3 31.5 39.5 28 700 43 800 6 000
NAG 4906UU ─ ─ 103 30 47 17 0.3 34 41.5 19 400 27 600 4 000
30 ─ NAU 4906UU ─ 102 30 47 17 0.3 34 41.5 13 000 16 200 5 500
─ ─ TRU 304830UU 197 30 48 30 0.3 35 42.5 29 400 46 600 5 500
32 ─ ─ TRU 325230UU 260 32 52 30 0.6 38 46 29 800 44 200 5 000
NAG 4907UU ─ ─ 172 35 55 20 0.6 40 49 28 700 43 800 3 500
35 ─ NAU 4907UU ─ 168 35 55 20 0.6 40 49 19 500 26 300 4 500
─ ─ TRU 355630UU 270 35 56 30 0.6 40 49 32 200 49 800 4 500
NAG 4908UU ─ ─ 225 40 62 22 0.6 46 56 34 600 49 500 3 000
40 ─ ─ TRU 405930UU 265 40 59 30 0.6 45 52.5 34 700 62 500 4 000
─ NAU 4908UU ─ 220 40 62 22 0.6 46 56 23 400 29 400 4 000

Notes(1)　　Minimum allowable value of chamfer dimension r

(2)  　  Allowable rotational speed applies to grease lubrication. Considering that the axial load acts under practical operating conditions,
up to 1/10 of this value is recommended for actual use.
Remarks1.　The NAG and NAU series with a bore diameter, d, of 17 mm or less have no oil hole. In others, the outer ring has an oil groove
and two oil holes.
2.　The bearings with seals are provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
E13 1mm=0.03937inch
E14
 ROLLER BEARINGS
Caged Roller Bearings With Seal C C

Full Complement Roller Bearings With Seal

r r

r r

d E7
d E7
Ew

Ew
D

J
d

d
r r

r r

NAG49 … UU NAU49 … UU
TRU … UU
Shaft dia. 42 − 80mm E
Identification number Mass Boundary dimensions　 Basic dynamic Basic static Allowable
(Ref.) mm load rating load rating rotational
speed(2)
Shaft Full complement Caged type (1) C C0
dia.
mm
type
g d D C rs min J Ew
N N min-1

42 ─ ─ TRU 426230UU 290 42 62 30 0.6 48 56.5 34 600 57 800 4 000

NAG 4909UU ─ ─ 265 45 68 22 0.6 51 61 36 400 54 700 2 500
45 ─ ─ TRU 456430UU 295 45 64 30 0.6 50.5 58.5 32 600 59 700 3 500
─ NAU 4909UU ─ 260 45 68 22 0.6 51 61 24 800 32 800 3 500
NAG 4910UU ─ ─ 270 50 72 22 0.6 55.5 65.5 38 200 59 900 2 500
50 ─ NAU 4910UU ─ 265 50 72 22 0.6 55.5 65.5 26 200 36 200 3 500
─ ─ TRU 507745UU 710 50 77 45 1 58 69 75 700 134 000 3 500
NAG 4911UU ─ ─ 395 55 80 25 1 61.5 72.5 48 100 77 700 2 000
55 ─ NAU 4911UU ─ 385 55 80 25 1 61.5 72.5 33 000 47 000 3 000
─ ─ TRU 558138UU 615 55 81 38 1 61.5 72.5 61 400 104 000 3 000
NAG 4912UU ─ ─ 425 60 85 25 1 67 77.5 50 300 84 300 2 000
60 ─ NAU 4912UU ─ 415 60 85 25 1 67 77.5 34 700 51 400 3 000
─ ─ TRU 608945UU 880 60 89 45 1 69.5 81.5 88 100 152 000 3 000

65 NAG 4913UU ─ ─ 455 65 90 25 1 72 83 53 200 93 000 1 900

─ NAU 4913UU ─ 440 65 90 25 1 72 83 36 900 57 100 2 500

70 NAG 4914UU ─ ─ 725 70 100 30 1 79 91.5 77 700 139 000 1 800

─ NAU 4914UU ─ 705 70 100 30 1 79 91.5 53 700 84 600 2 500
NAG 4915UU ─ ─ 775 75 105 30 1 83.5 95.5 80 000 146 000 1 700
75 ─ NAU 4915UU ─ 750 75 105 30 1 83.5 95.5 54 800 88 200 2 500
─ ─ TRU 7510845UU 1 240 75 108 45 1 85.5 98.5 103 000 190 000 2 000
NAG 4916UU ─ ─ 815 80 110 30 1 89.5 102 83 000 157 000 1 600
80
─ NAU 4916UU ─ 790 80 110 30 1 89.5 102 57 200 95 500 2 000

Notes(1)　　Minimum allowable value of chamfer dimension r

(2)  　  Allowable rotational speed applies to grease lubrication. Considering that the axial load acts under practical operating conditions,
up to 1/10 of this value is recommended for actual use.
Remarks1.　The outer ring has an oil groove and two oil holes.
2.　The bearings with seals are provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
E15 1mm=0.03937inch
E16
 ROLLER BEARINGS
Caged Roller Bearings With Seal C C

Full Complement Roller Bearings With Seal

r r

r r

d E7
d E7
Ew

Ew
D

J
d

d
r r

r r

NAG49 … UU NAU49 … UU
TRU … UU
Shaft dia. 85 − 140mm E
Identification number Mass Boundary dimensions　 Basic dynamic Basic static Allowable
(Ref.) mm load rating load rating rotational
speed(2)
Shaft Full complement Caged type (1) C C0
dia.
mm
type
g d D C rs min J Ew
N N min-1

NAG 4917UU ─ ─ 1 190 85 120 35 1.5 96 110 111 000 200 000 1 500
85 ─ ─ TRU 8511850UU 1 530 85 118 50 1 94.5 107.5 114 000 222 000 2 000
─ NAU 4917UU ─ 1 150 85 120 35 1.5 96 110 75 400 120 000 2 000
─ ─ TRU 8512045UU 1 500 85 120 45 1.5 96.5 110 110 000 215 000 2 000
NAG 4918UU ─ ─ 1 250 90 125 35 1.5 101 115.5 114 000 211 000 1 400
90 ─ NAU 4918UU ─ 1 210 90 125 35 1.5 101 115.5 79 500 130 000 1 900
─ ─ TRU 9012550UU 1 740 90 125 50 1.5 101 114 119 000 240 000 1 900

95 NAG 4919UU ─ ─ 1 300 95 130 35 1.5 106 120.5 117 000 222 000 1 300
─ NAU 4919UU ─ 1 270 95 130 35 1.5 106 120.5 81 000 136 000 1 800
NAG 4920UU ─ ─ 1 850 100 140 40 1.5 114.5 129.5 152 000 292 000 1 200
100 ─ ─ TRU 10013550UU 1 900 100 135 50 1.5 112 125.5 124 000 264 000 1 700
─ NAU 4920UU ─ 1 770 100 140 40 1.5 114.5 129.5 106 000 181 000 1 700
105 ─ ─ TRU 10515350UU 2 890 105 153 50 1.5 120 138 159 000 286 000 1 600

110 NAG 4922UU ─ ─ 2 010 110 150 40 1.5 123 138.5 161 000 322 000 1 100
─ NAU 4922UU ─ 1 930 110 150 40 1.5 123 138.5 113 000 200 000 1 600

120 NAG 4924UU ─ ─ 2 780 120 165 45 1.5 136 153.5 208 000 431 000 1 000
─ NAU 4924UU ─ 2 680 120 165 45 1.5 136 153.5 146 000 268 000 1 400
125 ─ ─ TRU 12517860UU 4 490 125 178 60 1.5 143.5 162 211 000 408 000 1 400

130 NAG 4926UU ─ ─ 3 750 130 180 50 2 147 165.5 240 000 495 000 950
─ NAU 4926UU ─ 3 610 130 180 50 2 147 165.5 166 000 304 000 1 300
135 ─ ─ TRU 13518860UU 4 790 135 188 60 1.5 154 172.5 220 000 442 000 1 300

140 NAG 4928UU ─ ─ 3 990 140 190 50 2 157.5 176 249 000 531 000 900
─ NAU 4928UU ─ 3 840 140 190 50 2 157.5 176 174 000 327 000 1 200

Notes(1)　　Minimum allowable value of chamfer dimension r

(2)  　  Allowable rotational speed applies to grease lubrication. Considering that the axial load acts under practical operating conditions,
up to 1/10 of this value is recommended for actual use.
Remarks1.　The outer ring has an oil groove and two oil holes.
2.　The bearings with seals are provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
E17 1mm=0.03937inch
E18
 ROLLER BEARINGS
B B
Roller Bearings for Sheaves C C
S C1 S C1
f f

r r

30 ° 30 °

c c

D2
D2
D

J
J

d
d
r r

NAS50 … UUNR NAS50 … ZZNR

Shaft dia. 40 − 170mm E

Identification number Mass Boundary dimensions　 Basic dynamic Basic static Allowable
(Ref.) mm load rating load rating rotational
speed(2)
Shaft Sealed type Shield type (1)
C C0
dia.
mm kg d D D2 B C C1 S f c rs min J
N N min-1

40 NAS 5008UUNR NAS 5008ZZNR   0.55 40 68 71.8 38 37 28 4.5 2 1.5 0.6 50 79 500 116 000 2 500
45 NAS 5009UUNR NAS 5009ZZNR   0.70 45 75 78.8 40 39 30 4.5 2 1.5 0.6 56 95 500 144 000 2 000
50 NAS 5010UUNR NAS 5010ZZNR   0.75 50 80 83.8 40 39 30 4.5 2 1.5 0.6 61 100 000 158 000 2 000
55 NAS 5011UUNR NAS 5011ZZNR   1.15 55 90 94.8 46 45 34 5.5 2.5 2 0.6 68 118 000 193 000 1 800
60 NAS 5012UUNR NAS 5012ZZNR   1.20 60 95 99.8 46 45 34 5.5 2.5 2 0.6 73 123 000 208 000 1 700
65 NAS 5013UUNR NAS 5013ZZNR   1.30 65 100 104.8 46 45 34 5.5 2.5 2 0.6 78 128 000 224 000 1 600
70 NAS 5014UUNR NAS 5014ZZNR   1.90 70 110 114.5 54 53 42 5.5 2.5 2 0.6 84 171 000 284 000 1 400
75 NAS 5015UUNR NAS 5015ZZNR   2.00 75 115 119.5 54 53 42 5.5 2.5 2 0.6 91 179 000 308 000 1 300
80 NAS 5016UUNR NAS 5016ZZNR   2.65 80 125 129.5 60 59 48 5.5 2.5 2 0.6 97 251 000 428 000 1 300
85 NAS 5017UUNR NAS 5017ZZNR   2.80 85 130 134.5 60 59 48 5.5 2.5 2 0.6 101 257 000 446 000 1 200
90 NAS 5018UUNR NAS 5018ZZNR   3.70 90 140 145.4 67 66 54 6 2.5 2.5 0.6 110 305 000 540 000 1 100
95 NAS 5019UUNR NAS 5019ZZNR   3.90 95 145 150.4 67 66 54 6 2.5 2.5 0.6 114 312 000 562 000 1 100
100 NAS 5020UUNR NAS 5020ZZNR   4.05 100 150 155.4 67 66 54 6 2.5 2.5 0.6 118 318 000 584 000 1 000
110 NAS 5022UUNR NAS 5022ZZNR   6.50 110 170 175.4 80 79 65 7 2.5 3 1 130 384 000 697 000 900
120 NAS 5024UUNR NAS 5024ZZNR   6.95 120 180 188.4 80 79 65 7 3 3 1 139.5 400 000 750 000 850
130 NAS 5026UUNR NAS 5026ZZNR 10.5 130 200 208.4 95 94 77 8.5 3 3 1 156 537 000 1 000 000 750
140 NAS 5028UUNR NAS 5028ZZNR 11.0 140 210 218.4 95 94 77 8.5 3 3 1 167 543 000 1 070 000 700
150 NAS 5030UUNR NAS 5030ZZNR 13.5 150 225 233.4 100 99 81 9 3 3.5 1 176.5 623 000 1 210 000 650
160 NAS 5032UUNR NAS 5032ZZNR 16.5 160 240 248.4 109 108 89 9.5 3 3.5 1.5 188.5 720 000 1 390 000 650
170 NAS 5034UUNR NAS 5034ZZNR 22.5 170 260 270 122 121 99 11 4 3.5 1.5 204.5 857 000 1 730 000 600

Notes(1)　　Minimum allowable value of chamfer dimension r

(2)  　  Allowable rotational speed applies to grease lubrication. Considering that the axial load acts under practical operating conditions,
up to 1/10 of this value is recommended for actual use.
Remarks1.　The inner ring has an oil groove and two oil holes.
2.　Roller Bearings for Sheaves are provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
E19 1mm=0.03937inch
E20
 ROLLER BEARINGS
B B
Roller Bearings for Sheaves C C
S C1 S C1
f f

r r

30 ° 30 °

c c

D2
D2
D

J
J

d
d
r r

NAS50 … UUNR NAS50 … ZZNR

Shaft dia. 180 − 440mm E

Identification number Mass Boundary dimensions　 Basic dynamic Basic static Allowable
(Ref.) mm load rating load rating rotational
speed(2)
Shaft Sealed type Shield type (1)
C C0
dia.
mm kg d D D2 B C C1 S f c rs min J
N N min-1

180 NAS 5036UUNR NAS 5036ZZNR 30.0 180 280 294 136 135 110 12.5 5 3.5 1.5 217 1 070 000 2 140 000 550
190 NAS 5038UUNR NAS 5038ZZNR 31.5 190 290 306 136 135 110 12.5 5 3.5 1.5 225 1 120 000 2 230 000 500
200 NAS 5040UUNR NAS 5040ZZNR 40.5 200 310 326 150 149 120 14.5 5 3.5 1.5 242 1 310 000 2 650 000 500
220 NAS 5044UUNR NAS 5044ZZNR 52.0 220 340 356 160 159 130 14.5 6 4 1.5 260 1 510 000 3 110 000 450
240 NAS 5048UUNR NAS 5048ZZNR 55.5 240 360 376 160 159 130 14.5 6 4 1.5 278.5 1 570 000 3 350 000 400
260 NAS 5052UUNR NAS 5052ZZNR 85.0 260 400 416 190 189 154 17.5 7 5 2 312 2 130 000 4 510 000 350
280 NAS 5056UUNR NAS 5056ZZNR 90.9 280 420 440 190 189 154 17.5 7 5 2 335 2 210 000 4 860 000 350

Notes(1)　　Minimum allowable value of chamfer dimension r

(2)  　  Allowable rotational speed applies to grease lubrication. Considering that the axial load acts under practical operating conditions,
up to 1/10 of this value is recommended for actual use.
Remarks1.　The inner ring has an oil groove and two oil holes.
2.　Roller Bearings for Sheaves are provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
E21 1mm=0.03937inch
E22
 ■ Structure and Features Structures of Thrust Bearings
Thrust Bearings consist of a precisely made
cage and rollers. They have high rigidity and high load
capacities and can be used in small spaces. Needle roller

Thrust Needle Roller Bearings incorporate needle

●Thrust Needle Roller Bearings rollers, while Thrust Roller Bearings incorporate cylin-
drical rollers. Various types of raceway rings are
●Thrust Roller Bearings
Cage
available, and suitable bearings can be selected
according to the operating conditions.
When the bearing mounting surfaces of a machine
are heat-treated and finished by grinding as race-
ways, Thrust Bearings can be used without raceway Cylindrical roller

rings allowing the machine to be made more compact.

They are most suited to applications where high accu-
racy is required at high speeds and under fluctuating
Cage
heavy loads, such as driving mechanisms for automo-
biles, machine tools, and high-pressure pumps.

F
Inner ring

Cylindrical roller

Cage

Outer ring

Inner ring

Outer ring

Thrust
washer

F1 F2
■ Types ■ Identification Number ■ Accuracy
In Thrust Bearings, the types shown in Table 1 The identification number of Thrust Bearings consists The accuracy of Thrust Bearings is based on JIS B
are available. of a model code, dimensions and a classification sym- 1514-2, -3 as shown in Table 2.
bol. Some examples are shown below.
Table 1.1 Type of bearing Table 2.1 Tolerances unit: μ m
Thrust needle Thrust roller bearings Item Dimension
Type
roller bearings Without inner and outer rings With inner and outer rings Examples of identification number Dimension
symbol
Tolerance
Type of bearing
Model code NTB AZK AZ Bore diameter d E11
Example 1 (In case of NTB or AS)
Thrust needle roller bearings NTB Outside diameter D c12
Table 1.2 Type of bearing ring
Model code Dimensions Width Dw Equivalent to JIS B 1506 Class 2
Type Inner ring Outer ring Thrust washer NTB 25 42 Bore diameter dc
As per Table 2.2
Outside diameter Dc
Model code WS GS AS Type of bearing AZK
Thrust roller bearings 1 ≦ Dw ≦ 10 Equivalent to JIS B 1506 Class 2
Width Dw
Bore diameter 10 ＜ Dw ≦ 30 Equivalent to JIS B 1506 Class 3
Thrust Needle Roller Bearings （25mm）
AZ Height T As per Table 2.3
Outside diameter Bore diameter d As per Table 2.4

F
These bearings consist of a cage made from a steel
（42mm） Inner rings
plate, which is precisely press formed and surface- WS Outside diameter D b12
hardened, and needle rollers with a diameter variation Width B h11
within 2 μ m. They have a rigid structure and a high Example 2 (In case of AZ or AZK) Bore diameter d B12
lubricant-retaining capacity. Classification Outer rings
Model code Dimensions symbol GS Outside diameter D As per Table 2.4
As they have the lowest sectional height compared Width B h11
with other thrust bearings, they can be used instead AZ 25 42 11 P5
Bore diameter d E12
of conventional thrust washers and can withstand
Type of bearing Thrust washers AS Outside diameter D e12
high-speed rotations with a low coefficient of friction.
Specially designed thin inner rings (WS) and outer Width s ± 50
Bore diameter
rings (GS), and especially thin (1 mm thick) thrust （25mm）
washers (AS), are available for use in various applica-
Outside diameter Table 2.2 T
 olerances of bore and outside
tions.
（42mm） diameters for AZK series unit: μ m Table 2.3 Tolerances of height for AZ series unit: μ m
These bearings are generally used by utilizing their
inner surface as the guide surface. Bearing height ∆dc ∆Dc d ∆Ts
Nominal dimension
（11mm） mm
Cage bore diameter Cage outside Nominal bearing bore dia. Deviation of an actual bearing height
deviation diameter deviation mm
Thrust Roller Bearings Accuracy class（1）
（Class 5） Over Incl. High Low High Low Over Incl. High Low
In this series, the caged cylindrical rollers AZK and −   50 ＋ 100 0 0 −  300 −   18 0 −   75
the complete bearings AZ in which AZK are combined ＋ 200 −  400 −   75
Example 3 (In case of WS or GS)   50 100 0 0   18   30 0
with an inner ring (WS) and an outer ring (GS) are
Classification 100 200 ＋ 300 0 0 −  500   30   50 0 − 100
available. Model code Dimensions symbol
200 300 ＋ 500 0 0 −  700   50   80 0 − 125
The cage has a special precise structure which is
highly rigid, and cylindrical rollers are outwardly
WS 25 42 P5 300 400 ＋ 700 0 0 − 1000   80 120 0 − 150
arranged and guided by the cage with exact precision Type of bearing ring
400 500 − − 0 − 1200 120 180 0 − 175
to enable them to withstand heavy loads even at high 180 250 0 − 200
rotational speeds. Bore diameter 250 315 0 − 225
Owing to the high accuracy of the bearing height T, （25mm）
315 400 0 − 300
they are suitable for use in machine tools, ultra-high Outside diameter 400 500 0 − 400
pressure pumps, etc. （42mm）
These bearings are generally used by utilizing their
Accuracy class
inner surface as the guide surface.
（Class 5）

Note(1)　Not applicable to the model AZK.

1N=0.102kgf=0.2248lbs.
F3 1mm=0.03937inch
F4
Table 2.4 Tolerances and allowable values for WS and GS unit: μ m
■ Fit ■ Mounting
d or D (1) Inner ring Outer ring Inner ring or outer ring
Nominal bearing bore The recommended fits for Thrust Bearings are shown When mounting Thrust Bearings, the following items
∆dmp Vdsp ∆Dmp VDsp
dia. or outside dia. Si or Se (2) in Table 3. should be considered.
Single plane mean bore Bore diameter Single plane mean outside Outside diameter Bearing ring thickness variation
 1 When inner and outer rings are not used, the hard-
diameter deviation variation in a sin- diameter deviation variation in a sin-
gle radial plane gle radial plane Table 3 Recommended fits ness of the raceway surfaces should be 58 〜 64HRC,
mm Class 0 Class 6 Class 5
the effective hardening depth should be adequate,
Over Incl. High Low Max. High Low Max. Max. Tolerance class
Type of bearing and the surface roughness should be less than 0.2μ
−   18 0 − 8   6 0 − 11   8 10   5 3 Shaft Housing bore
mRa.
  18   30 0 − 10   8 0 − 13 10 10   5 3 Thrust needle roller  2 When mounting inner and outer rings to shaft and
bearings
NTB h8 ──
  30   50 0 − 12   9 0 − 16 12 10   6 3 housing bore, dimensions related to mounting should
  50   80 0 − 15 11 0 − 19 14 10   7 4 AZK ── be based on the dimension tables.
Thrust roller bearings h6
AZ H7 Also, the mounting surfaces should be finished at
  80 120 0 − 20 15 0 − 22 17 15   8 4
right angles to the center axis and they should be suf-
120 180 0 − 25 19 0 − 25 19 15   9 5 Inner rings WS h6 ── ficiently rigid.
180 250 0 − 30 23 0 − 30 23 20 10 5  3 To avoid elastic deformation, the thrust washer AS
250 315 0 − 35 26 0 − 35 26 25 13 7 must be seated uniformly on its mating surface.
Outer rings GS ── H7
315 400 0 − 40 30 0 − 40 30 30 15 7 A small warp in an AS washer will be corrected auto-
400 500 0 − 45 34 0 − 45 34 30 18 9 matically when an axial load is applied.

F
Thrust washers AS h8 ──  4 Thrust Roller Bearings are combinations of a cop-
Notes(1)　d for ∆dmp and Vdp, and D for ∆Dmp and VDp, respectively.
d for thickness variations of inner and outer rings . per alloy component and cylindrical rollers. When
(2)　di for thickness variations of rings for NAX(l) and NBX(l) . handling the AZK itself, care should be taken to pre-
vent deformations, blemishes, etc.

Table 2.5 P
 ermissible limit values for chamfer
dimension
Side surface of
inner ring or
outer ring

(Radial direction)
r s m
in

rs max
rs min

Bearing bore or
bearing outside rs min
surface

rs max
(Axial direction)
unit: mm

Radial and axial directions

rs min
rs max
0.3 0.8
0.6 1.5
1 2.2
1.1 2.7
1.5 3.5
2 4
2.1 4.5
3 5.5 Fig.1 Mounting examples
4 6.5
5 8

1N=0.102kgf=0.2248lbs.
F5 1mm=0.03937inch
F6
 THRUST BEARINGS
Thrust Needle Roller Bearings
Dw S B B

D e 12

d B12
d E 12

D b 12

D
D

Ce
Ci
d

d
NTB AS WS GS
Shaft dia. 10 − 85mm

Identification number Boundary dimensions Basic dynamic Basic static Allowable

Shaft mm load rating load rating rotational
speed(2)
C C0
F
dia.
Thrust Mass Thrust washer Mass Inner ring Outer ring Mass (1)
mm
needle roller bearing (Ref.)
g
(Ref.)
g
(Ref.)
g
d D Dw s B rs min Ci Ce
N N min-1

10 NTB   1024 3.3 AS   1024 2.9 WS   1024 GS   1024 8 10 24 2 1 2.75 0.3 14 22 7 820 23 900 15 000
12 NTB   1226 3.8 AS   1226 3.2 WS   1226 GS   1226 8.9 12 26 2 1 2.75 0.3 16 24 8 340 26 900 13 000
15 NTB   1528 4.1 AS   1528 3.4 WS   1528 GS   1528 9.3 15 28 2 1 2.75 0.3 18 26 8 830 29 900 12 000
16 NTB   1629 4.3 AS   1629 3.6 WS   1629 GS   1629 9.8 16 29 2 1 2.75 0.3 19 27 9 070 31 400 11 000
17 NTB   1730 4.5 AS   1730 3.7 WS   1730 GS   1730 10.2 17 30 2 1 2.75 0.3 20 28 9 320 32 900 11 000
18 NTB   1831 4.7 AS   1831 3.9 WS   1831 GS   1831 10.7 18 31 2 1 2.75 0.3 21 29 9 550 34 400 10 000
20 NTB   2035 6.1 AS   2035 5 WS   2035 GS   2035 13.8 20 35 2 1 2.75 0.3 23 33 11 700 46 500 9 000
25 NTB   2542 8.2 AS   2542 6.9 WS   2542 GS   2542 21 25 42 2 1 3 0.6 29 40 14 400 64 700 7 500
30 NTB   3047 9.4 AS   3047 7.9 WS   3047 GS   3047 24 30 47 2 1 3 0.6 34 45 15 400 73 300 6 500
35 NTB   3552 10.6 AS   3552 8.9 WS   3552 GS   3552 31.5 35 52 2 1 3.5 0.6 39 50 16 300 81 900 5 500
40 NTB 40603 22 AS   4060 12.1 WS   4060 GS   4060 42.5 40 60 3 1 3.5 0.6 45 57 24 200 108 000 5 000
45 NTB   4565 24.5 AS   4565 13.3 WS   4565 GS   4565 53.5 45 65 3 1 4 0.6 50 62 25 900 121 000 4 500
50 NTB   5070 26.5 AS   5070 14.5 WS   5070 GS   5070 58.5 50 70 3 1 4 0.6 55 67 27 600 135 000 4 000
55 NTB   5578 33.5 AS   5578 18.5 WS   5578 GS   5578 93 55 78 3 1 5 0.6 61 75 32 400 171 000 4 000
60 NTB   6085 38.5 AS   6085 22 WS   6085 GS   6085 105 60 85 3 1 4.75 1 66 82 38 200 219 000 3 500
65 NTB   6590 41.5 AS   6590 23.5 WS   6590 GS   6590 124 65 90 3 1 5.25 1 71 87 40 100 237 000 3 000
70 NTB   7095 61 AS   7095 25 WS   7095 GS   7095 132 70 95 4 1 5.25 1 75 91 47 400 244 000 3 000
75 NTB 75100 65 AS 75100 26.5 WS 75100 GS 75100 153 75 100 4 1 5.75 1 80 96 48 400 256 000 3 000
80 NTB 80105 68.5 AS 80105 28 WS 80105 GS 80105 162 80 105 4 1 5.75 1 85 101 49 500 267 000 2 500
85 NTB 85110 72 AS 85110 29.5 WS 85110 GS 85110 170 85 110 4 1 5.75 1 90 106 50 300 279 000 2 500

Notes(1)　Minimum allowable value of chamfer dimension r

(2)　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 25% of this value is allowable.

1N=0.102kgf=0.2248lbs.
F7 1mm=0.03937inch
F8
 THRUST BEARINGS
Thrust Needle Roller Bearings
Dw S B B

D e 12

d B12
d E 12

D b 12

D
D

Ce
Ci
d

d
NTB AS WS GS
Shaft dia. 90 − 130mm

Identification number Boundary dimensions Basic dynamic Basic static Allowable

Shaft mm load rating load rating rotational
speed(2)
C C0
F
dia.
Thrust Mass Thrust washer Mass Inner ring Outer ring Mass (1)
mm
needle roller bearing (Ref.)
g
(Ref.)
g
(Ref.)
g
d D Dw s B rs min Ci Ce
N N min-1

90 NTB 90120 92 AS 90120 38 WS 90120 GS 90120 250 90 120 4 1 6.5 1 96 116 64 500 394 000 2 500
100 NTB 100135 119 AS 100135 50 WS 100135 GS 100135 350 100 135 4 1 7 1 107 131 80 300 541 000 2 000
110 NTB 110145 129 ─ ─ WS 110145 GS 110145 380 110 145 4 ─ 7 1 117 141 83 200 578 000 2 000
120 NTB 120155 139 ─ ─ WS 120155 GS 120155 410 120 155 4 ─ 7 1 127 151 87 900 634 000 1 800
130 NTB 130170 225 ─ ─ WS 130170 GS 130170 660 130 170 5 ─ 9 1 137 165 120 000 839 000 1 700

Notes(1)　Minimum allowable value of chamfer dimension r

(2)　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 25% of this value is allowable.

1N=0.102kgf=0.2248lbs.
F9 1mm=0.03937inch
F10
 THRUST BEARINGS
Thrust Roller Bearings T Dw B B
r r

r r

d B12

d B12
D b12

D b 12

Da
da
Dc

Ce
Ci

D
D

dc

d
AZ AZK WS GS
Shaft dia. 10 − 65mm

Identification number Boundary dimensions Standard mounting Basic dynamic Basic static Allowable
Shaft mm dimensions　mm load rating load rating rotational
speed(2)
C C0
F
dia.
Thrust Mass Thrust Mass Inner ring Outer ring Mass (1) da Da
mm
roller bearing (Ref.)
g
roller bearing (Ref.)
g
(Ref.)
g
d D T dc Dc Dw B rs min Ci Ce Min. Max.
N N min-1

10 AZ  10249      24.6 AZK 10243.5     8.6 WS   1024 GS   1024     8 10 24   9 10.04 23.6 3.5 2.75 0.3 13 21 21 13 8 990 19 100 18 000
12 AZ  12269      26.5 AZK 12263.5     8.7 WS   1226 GS   1226     8.9 12 26   9 12.04 25.6 3.5 2.75 0.3 15 23 23 16 10 400 23 900 16 000
15 AZ  15289      28 AZK 15283.5     9.4 WS   1528 GS   1528     9.3 15 28   9 15.04 27.6 3.5 2.75 0.3 17 25 25 18 10 200 23 900 14 000
17 AZ  17309      30.5 AZK 17303.5   10.1 WS   1730 GS   1730   10.2 17 30   9 17.04 29.6 3.5 2.75 0.3 19 27 27 20 11 400 28 600 13 000
20 AZ 203510      45.5 AZK 20354.5   17.9 WS   2035 GS   2035   13.8 20 35 10 20.04 34.6 4.5 2.75 0.3 22 33 33 23 19 000 48 700 11 000
25 AZ 254211      70 AZK 25425   28 WS   2542 GS   2542   21 25 42 11 25.05 41.6 5 3 0.6 28 39 39 28 22 700 60 700 9 000
AZ 304711      79 AZK 30475   31 WS   3047 GS   3047   24 30 47 11 30.05 46.5 5 3 0.6 33 44 44 33 27 400 81 000 8 000
30
AZ 305216    160 AZK 30527.5   70 WS   3052 GS   3052   45 30 52 16 30.05 51.5 7.5 4.25 0.6 35 49 48 36 38 400 95 700 7 500
AZ 355212      99 AZK 35525   36 WS   3552 GS   3552   31.5 35 52 12 35.05 51.5 5 3.5 0.6 38 49 49 39 29 100 91 100 7 000
35
AZ 356218    260 AZK 35627.5   98 WS   3562 GS   3562   81 35 62 18 35.05 61.5 7.5 5.25 1 42 58 57 43 47 900 135 000 6 500
AZ 406013    139 AZK 40606   54 WS   4060 GS   4060   42.5 40 60 13 40.05 59.5 6 3.5 0.6 44 57 57 44 41 700 133 000 6 000
40
AZ  406819    310 AZK 40689 132 WS   4068 GS   4068   89 40 68 19 40.05 67.5 9 5 1 45 64 64 46 68 700 195 000 5 500
AZ 456514    169 AZK 45656   62 WS   4565 GS   4565   53.5 45 65 14 45.05 64.5 6 4 0.6 49 62 62 49 40 800 133 000 5 500
45
AZ 457320    360 AZK 45739 144 WS   4573 GS   4573 108 45 73 20 45.05 72.5 9 5.5 1 50 69 69 51 75 700 227 000 5 000
AZ 507014    185 AZK     50706   68 WS   5070 GS   5070   58.5 50 70 14 50.05 69.5 6 4 0.6 54 67 67 54 43 300 148 000 5 000
50
AZ 507822    430 AZK   507811 194 WS   5078 GS   5078 118 50 78 22 50.05 77.5 11 5.5 1 55 74 73 56 84 300 232 000 4 500
AZ 557816    275 AZK     55786   89 WS   5578 GS   5578   93 55 78 16 55.05 77.5 6 5 0.6 59 75 75 60 51 700 192 000 4 500
55
AZ 559025    725 AZK   559011 275 WS   5590 GS   5590 225 55 90 25 55.05 89.5 11 7 1 63 85 84 63 108 000 332 000 4 000
AZ 608517    345 AZK     60857.5 135 WS   6085 GS   6085 105 60 85 17 60.05 84.5 7.5 4.75 1 65 81 81 66 64 600 224 000 4 000
60 AZ   609526    770 AZK   609511 290 WS   6095 GS   6095 240 60 95 26 60.05 94.5 11 7.5 1 68 90 89 68 106 000 332 000 4 000
AZ 6013026 2 090 AZK 6013010 790 WS 60130 GS 60130 650 60 130 26 60.05 129.5 10 8 1.5 79 119 119 80 158 000 634 000 3 000
AZ   659018    380 AZK 65907.5 132 WS   6590 GS   6590 124 65 90 18 65.05 89.5 7.5 5.25 1 70 86 86 71 68 300 247 000 4 000
65 AZK 6510011
AZ 6510027    860 310 WS 65100 GS 65100 275 65 100 27 65.05 99.5 11 8 1 73 95 94 73 116 000 379 000 3 500

Notes(1)　Minimum allowable value of chamfer dimension r

(2)　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 25% of this value is allowable.

1N=0.102kgf=0.2248lbs.
F11 1mm=0.03937inch
F12
 THRUST BEARINGS
Thrust Roller Bearings T Dw B B
r r

r r

d B12

d B12
D b12

D b 12

Da
da
Dc

Ce

D
Ci
D

dc

d
AZ AZK WS GS
Shaft dia. 70 − 130mm

Identification number Boundary dimensions Standard mounting Basic dynamic Basic static Allowable
Shaft mm dimensions　mm load rating load rating rotational
speed(2)
C C0
F
dia.
Thrust Mass Thrust Mass Inner ring Outer ring Mass (1) da Da
mm
roller bearing (Ref.)
g
roller bearing (Ref.)
g
(Ref.)
g
d D T dc Dc Dw B rs min Ci Ce Min. Max.
N N min-1

AZ 709518 420 AZK 70957.5 156 WS 7095 GS 7095 132 70 95 18   70.05 94.5   7.5 5.25 1 75 91 91 76 72 000 269 000 3 500
70 AZ 7010527 905 AZK 7010511 325 WS 70105 GS 70105 290 70 105 27   70.05 104.5 11 8 1 78 100 99 78 114 000 379 000 3 500
AZ 7014026 2 250 AZK 7014010 890 WS 70140 GS 70140 680 70 140 26   70.05 139.5 10 8 1.1 89 129 129 90 169 000 713 000 3 000
AZ 7510019 465 AZK 751007.5 159 WS 75100 GS 75100 153 75 100 19   75.05 99.5   7.5 5.75 1 80 96 96 81 71 100 269 000 3 500
75
AZ 7511027 960 AZK 7511011 340 WS 75110 GS 75110 310 75 110 27   75.05 109.5 11 8 1 83 105 104 83 123 000 427 000 3 000
AZ 8010519 495 AZK 801057.5 171 WS 80105 GS 80105 162 80 105 19   80.05 104.5   7.5 5.75 1 85 101 101 86 74 500 292 000 3 000
80 AZ 8011528 1 060 AZK 8011511 370 WS 80115 GS 80115 345 80 115 28   80.05 114.5 11 8.5 1 88 110 109 88 122 000 427 000 3 000
AZ 8015026 2 500 AZK 8015010 920 WS 80150 GS 80150 790 80 150 26   80.05 149.5 10 8 1.5 99 139 139 100 180 000 792 000 2 500
AZ 8511019 530 AZK 851107.5 190 WS 85110 GS 85110 170 85 110 19   85.05 109.5   7.5 5.75 1 90 106 106 91 77 800 314 000 3 000
85
AZ 8512531 1 460 AZK 8512512 510 WS 85125 GS 85125 475 85 125 31   85.05 124.5 12 9.5 1 95 119 118 95 145 000 513 000 3 000
AZ 9012022 790 AZK 901209 290 WS 90120 GS 90120 250 90 120 22   90.05 119.5   9 6.5 1 97 116 115 97 99 700 390 000 3 000
90 AZ 9013535 2 040 AZK 9013514 750 WS 90135 GS 90135 645 90 135 35   90.05 134.5 14 10.5 1.1 100 129 128 101 181 000 626 000 2 500
AZ 9016026 2 710 AZK 9016010 1 000 WS 90160 GS 90160 855 90 160 26   90.05 159.5 10 8 1.5 109 149 149 110 189 000 871 000 2 500
AZ 10013525 1 190 AZK 10013511 490 WS 100135 GS 100135 350 100 135 25 100.05 134.5 11 7 1 108 130 129 108 136 000 522 000 2 500
100 AZ 10015038 2 720 AZK 10015015 980 WS 100150 GS 100150 870 100 150 38 100.05 149.5 15 11.5 1.1 112 143 142 113 219 000 796 000 2 500
AZ 10019039 5 960 AZK 10019015 2 120 WS 100190 GS 100190 1 920 100 190 39 100.1 189.3 15 12 1.5 119 179 177 120 333 000 1 420 000 2 000
AZ 11014525 1 350 AZK 11014511 590 WS 110145 GS 110145 380 110 145 25 110.1 144.5 11 7 1 118 140 139 118 142 000 569 000 2 500
110 AZ 11016040 3 220 AZK 11016017 1 320 WS 110160 GS 110160 950 110 160 40 110.1 159.5 17 11.5 1.1 120 154 153 121 282 000 1 030 000 2 000
AZ 11020039 6 400 AZK 11020015 2 280 WS 110200 GS 110200 2 060 110 200 39 110.1 199.3 15 12 2 129 188 187 130 388 000 1 770 000 2 000
AZ 12015525 1 450 AZK 12015511 630 WS 120155 GS 120155 410 120 155 25 120.1 154.5 11 7 1 128 150 149 128 149 000 617 000 2 000
120 AZ 12017542 4 020 AZK 12017518 1 640 WS 120175 GS 120175 1 190 120 175 42 120.1 174.5 18 12 1.1 132 168 167 133 313 000 1 160 000 2 000
AZ 12022039 7 730 AZK 12022015 2 730 WS 120220 GS 120220 2 500 120 220 39 120.1 219 15 12 2.1 141 207 206 142 415 000 1 980 000 1 800
AZ 13017030 2 180 AZK 13017012 860 WS 130170 GS 130170 660 130 170 30 130.1 169.5 12 9 1 140 164 163 140 176 000 741 000 2 000
130 AZ 13018542 4 300 AZK 13018518 1 760 WS 130185 GS 130185 1 270 130 185 42 130.1 184.5 18 12 1.5 142 178 177 143 333 000 1 290 000 1 900
AZ 13023039 8 240 AZK 13023015 2 940 WS 130230 GS 130230 2 650 130 230 39 130.1 229 15 12 2.1 151 217 216 152 440 000 2 180 000 1 700

Notes(1)　Minimum allowable value of chamfer dimension r

(2)　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 25% of this value is allowable.

1N=0.102kgf=0.2248lbs.
F13 1mm=0.03937inch
F14
 THRUST BEARINGS
Thrust Roller Bearings T Dw B B
r r

r r

d B12

d B12
D b12

D b 12

Da
da
Dc

Ce

D
Ci
D

dc

d
AZ AZK WS GS
Shaft dia. 140 − 280mm

Identification number Boundary dimensions Standard mounting Basic dynamic Basic static Allowable
Shaft mm dimensions　mm load rating load rating rotational
speed(2)
C C0
F
dia.
Thrust Mass Thrust Mass Inner ring Outer ring Mass (1) da Da
mm
roller bearing (Ref.)
g
roller bearing (Ref.)
g
(Ref.)
g
d D T dc Dc Dw B rs min Ci Ce Min. Max.
N N min-1

AZ 14018031 2 410 AZK 14018012 920 WS 140180 GS 140180 745 140 180 31 140.1 179.5 12   9.5 1 150 174 173 150 184 000 798 000 1 900
140 AZ 14019542 4 560 AZK 14019518 1 860 WS 140195 GS 140195 1 350 140 195 42 140.1 194.5 18 12 1.5 152 188 187 153 353 000 1 420 000 1 800
AZ 14024039 8 680 AZK 14024015 3 100 WS 140240 GS 140240 2 790 140 240 39 140.1 239 15 12 2.1 161 227 226 162 435 000 2 180 000 1 600
AZ 15019031 2 560 AZK 15019012 980 WS 150190 GS 150190 790 150 190 31 150.1 189.5 12   9.5 1 160 184 183 160 181 000 798 000 1 800
150 AZ 15020542 4 840 AZK 15020518 1 980 WS 150205 GS 150205 1 430 150 205 42 150.1 204.5 18 12 1.5 162 198 197 163 349 000 1 420 000 1 700
AZ 15025039 9 140 AZK 15025015 3 260 WS 150250 GS 150250 2 940 150 250 39 150.1 249 15 12 2.1 171 237 236 172 459 000 2 380 000 1 500
AZ 16020031 2 710 AZK 16020012 1 030 WS 160200 GS 160200 840 160 200 31 160.1 199.5 12   9.5 1 170 194 193 170 189 000 855 000 1 700
160
AZ 16027039 10 800 AZK 16027015 3 840 WS 160270 GS 160270 3 480 160 270 39 160.1 269 15 12 3 183 256 255 184 519 000 2 850 000 1 400
AZ 17023045 6 220 AZK 17023019 2 420 WS 170230 GS 170230 1 900 170 230 45 170.1 229 19 13 1.5 183 221 220 184 406 000 1 730 000 1 500
170
AZ 17028039 11 300 AZK 17028015 4 020 WS 170280 GS 170280 3 640 170 280 39 170.1 279 15 12 3 193 266 265 194 543 000 3 070 000 1 300
AZ 18024045 6 540 AZK 18024019 2 540 WS 180240 GS 180240 2 000 180 240 45 180.1 239 19 13 1.5 193 231 230 194 426 000 1 870 000 1 400
180
AZ 18031039 14 600 AZK 18031015 5 200 WS 180310 GS 180310 4 700 180 310 39 180.1 308 15 12 3 204 294 293 205 619 000 3 710 000 1 200
AZ 19025548 8 060 AZK 19025520 3 100 WS 190255 GS 190255 2 480 190 255 48 190.1 254 20 14 2 205 245 244 206 470 000 2 080 000 1 300
190
AZ 19032039 15 000 AZK 19032015 5 280 WS 190320 GS 190320 4 860 190 320 39 190.1 318 15 12 4 214 304 303 215 647 000 3 980 000 1 200
AZ 20026548 8 430 AZK 20026520 3 250 WS 200265 GS 200265 2 590 200 265 48 200.15 264 20 14 2 215 255 254 216 465 000 2 080 000 1 300
200
AZ 20034039 17 200 AZK 20034015 6 120 WS 200340 GS 200340 5 540 200 340 39 200.15 338 15 12 4 227 323 322 228 710 000 4 580 000 1 100
AZ 22029050 10 400 AZK 22029022 4 280 WS 220290 GS 220290 3 060 220 290 50 220.15 289 22 14 2 236 280 278 237 557 000 2 530 000 1 300
220
AZ 22036052 24 000 AZK 22036020 8 000 WS 220360 GS 220360 8 000 220 360 52 220.15 358 20 16 4 246 343 342 247 943 000 5 520 000 1 000
AZ 24031554 13 200 AZK 24031524 5 520 WS 240315 GS 240315 3 840 240 315 54 240.15 314 24 15 2 256 304 302 257 695 000 3 250 000 1 100
240
AZ 24038052 26 500 AZK 24038020 9 440 WS 240380 GS 240380 8 530 240 380 52 240.15 378 20 16 4 266 363 362 267 977 000 5 910 000 1 000
AZ 26034055 15 400 AZK 26034025 6 600 WS 260340 GS 260340 4 400 260 340 55 260.15 339 25 15 2.1 278 328 326 279 739 000 3 510 000 1 000
260
AZ 26042080 51 600 AZK 26042030 18 200 WS 260420 GS 260420 16 700 260 420 80 260.15 418 30 25 5 289 402 400 291 1 430 000 7 490 000 900
280 AZ 28044080 54 600 AZK 28044030 19 200 WS 280440 GS 280440 17 700 280 440 80 280.15 438 30 25 5 309 422 420 311 1 420 000 7 490 000 800

Notes(1)　Minimum allowable value of chamfer dimension r

(2)　Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 25% of this value is allowable.

1N=0.102kgf=0.2248lbs.
F15 1mm=0.03937inch
F16
 ■ Structure and Features Structures of Combined Type
Needle Roller Bearings
Combined Type Needle Roller Bearings are
combinations of a radial bearing and a thrust bearing.
Dust cover
Caged needle roller bearings are used as radial bear-
ings and thrust ball bearings or thrust roller bearings Bearing ring for Thrust ball bearing

●Needle Roller Bearings with Thrust Ball Bearing are used as thrust bearings. They are compact and thrust bearing

very economical, and can be subjected to radial loads

●Needle Roller Bearings with Thrust Roller Bearing and axial loads simultaneously.
Inner ring
They are widely used for machine tools, textile
●Needle Roller Bearings with Angular Contact Ball Bearing
Outer ring
machinery, and industrial machinery.
●Needle Roller Bearings with Three-point Contact Ball Bearing
Radial
needle roller bearing

■ Types
The types of Combined Type Needle Roller Bearings
Bearing ring for Radial needle roller bearing
shown in Table 1 are available. thrust bearing

Table 1.1 Type of bearing

Combined with Combined with
Inner ring
Type thrust ball bearing thrust roller bearing Outer ring
Without inner ring With inner ring Without inner ring With inner ring

G
── NAX NAXI NBX NBXI
With dust cover NAX … Z NAXI … Z NBX … Z NBXI … Z
Thrust roller bearing

Table 1.2 Type of bearing

Combined with angular Combined with three-point
Type
contact ball bearing contact ball bearing
Outer ring
Model code NATA NATB
Inner ring

Needle Roller Bearings with Thrust Ball Needle roller cage

Bearing
Ball cage
In this series, needle roller bearings are combined (Angular contact type)
with thrust ball bearings to receive thrust loads.
In bearings with a dust cover, the dust cover is formed
from a thin steel plate and fixed to a groove cut on the Needle roller cage

outer cylindrical surface of the outer ring collar. The

cover forms a labyrinth with the thrust raceway ring, Outer ring
and is therefore effective in preventing leakage of
grease and penetration of dust and dirt. Inner ring(A) Inner ring(B)

In the case of bearings without an inner ring, the toler-

ances of roller set bore diameter Fw are shown in
Table 14 on page A33. Therefore, the required radial
internal clearances can be selected by combining the Ball cage
bearings with shafts that have been heat-treated and (3-point contact type)

finished by grinding as shown in Table 23 on page

A42 and Table 26 on page A44.

G1 G2
Needle Roller Bearings with Thrust Roller
Bearing
■ Identification Number Table 2 Tolerances
Item Dimension
unit: mm
■ Rating Life
The identification number of Combined Type Needle Type of Dimension Tolerance In Combined Type Needle Roller Bearings, caged
bearing symbol
In this series, needle roller bearings are combined Roller Bearings consists of a model code, dimen- needle roller bearings are subjected to radial loads
with thrust roller bearings to receive thrust loads. sions, any supplemental codes and a classification Bore dia. of bearing ring while thrust bearings receive axial loads. Therefore, it
di E7
for thrust bearing
Their axial load ratings are greater than those of bear- symbol. Some examples are shown below. is necessary to calculate their lives respectively (page
ings that are combined with thrust ball bearings. Also, NAX(I)(1)
　0 A17).
Assembled bearing width L
elastic deformation of the rolling contact surfaces NBX(I)(1) − 0.25
under load is minimal. Furthermore, the thrust bear- Examples of identification number
Bearing height of thrust bearing H
　0 ■ Mounting
ing section is finished to high accuracy, and therefore − 0.20
Fig.1 shows mounting examples of Combined Type
high rotational accuracy is obtained in the case of 　0
Supplemental Classification NATB59 Width of inner ring B Needle Roller Bearings. When applying preload to the
both vertical and horizontal shafts. Example 1 Model code Dimensions code symbol − 0.3
NAX and NBX models, it is recommended that thrust
Like the needle roller bearings with thrust ball bearing, Note(1)　Also applicable to bearings with dust cover
this series also includes bearings with a dust cover
NAXI 17 30 Z P6 raceway rings are not tightened directly with nuts, but
are tightened using springs as shown in Fig. 2.
■ Clearance
and bearings with an inner ring.
Type of bearing Mounting two NATA models symmetrically allows
them to be subjected to two-way axial loads. When
Bearing bore diameter Combined Type Needle Roller Bearings are manufac-
Needle Roller Bearings with Angular Con- （17mm） mounting these models, an axial clearance of 0.2 〜
tured to have the radial internal clearance CN shown
tact Ball Bearing 0.3 mm should be provided in the angular contact ball
Assembled bearing width in Table 18 on page A37.
bearings so that radial loads are not applied to the
In this series, caged needle roller bearings are com- （30mm）
angular contact ball bearings.
bined with angular contact ball bearings to receive
thrust loads. These bearings conform to the interna-
With dust cover ■ Fit Dimensions related to mounting should be based on
the table of dimensions.
tional dimension series #59, which is based on the The recommended fits for Combined Type Needle
Accuracy class

G
ISO Standard. They can withstand heavy radial loads (Class 6) Roller Bearings are shown in Table 3.
and unidirectional axial loads simultaneously.
Example 2 Model code Dimensions Table 3 Recommended fits
When the axial load exceeds 25% of the radial load,
Item Tolerance class
the radial load will be induced in the angular contact NATA 59 05
ball bearing, and bearing life will be affected. The Shaft
Type of Housing bore
relationship between the two loads must therefore be Type of bearing bearing Without inner ring With inner ring
taken into careful consideration. NAX(I)(1)
Dimension series h5，k5 k5 K6，M6
NBX(I)(1)
Bore diameter number NATA59
Needle Roller Bearings with Three-point NATB59
── k5(2) M6(2)
Contact Ball Bearing
Notes(1)　T he housing bore for the thrust bearing must be
These bearings can withstand heavy radial loads and machined to be more than 0.5 mm larger than the out-
side diameters D 1 and D 2 to ensure that it does not
bi-directional axial loads at the same time during high-
■ Accuracy
incur radial loads.
speed rotation. ( )　If the fit is made tighter than specified in this table, radial
2

loads will act upon the thrust bearing, limiting its function.
Since the non-interchangeable inner rings are sepa-
Dimensional accuracy and rotational accuracy of
■ Lubrication
rated at the center of the ball raceway surface, they
Combined Type Needle Roller Bearings are based on Fig.1 Mounting examples
must be firmly tightened against the shaft in the axial
Table 2 below and Tables 12 and 13 on page A31.
direction. The axial clearance of this bearing is 0.1 〜 Grease is not prepacked in Combined Type Needle
The tolerances for the smallest single roller set bore
0.3 mm, and like NATA59, the axial load should not Roller Bearings, so perform proper lubrication for use.
diameter of bearings without inner ring are based on
exceed 25% of the radial load. Operating without lubrication will increase the wear of
Table 14 on page A33. Thickness variations of thrust
rings of NAX(I) and NBX(I) are based on Table 2.4 on the rolling contact surfaces and shorten the bearing
page F5. life.

■ Oil Hole
Bore diameter of the small width inner ring of NATB59
is made for a transition fit with k5 tolerance shaft.
The outer ring of Combined Type Needle Roller Fig.2 Mounting example when applying preload
Bearings has an oil groove and an oil hole. When
outer rings with multiple oil holes or inner rings with oil
hole(s) are required, please contact .

1N=0.102kgf=0.2248lbs.
G3 1mm=0.03937inch
G4
 COMBINED TYPE NEEDLE ROLLER BEARINGS
Needle Roller Bearings with Thrust Ball Bearing Without Inner Ring
Needle Roller Bearings with Thrust Roller Bearing Without Inner Ring L L
H l1 H l1

r r

r r

Fw
D1

D1

Fw

D2
D2
D

D
di

di

da
NAX NAX … Z NBX NBX … Z

Shaft dia. 10 − 70mm

Identification number Boundary dimensions Standard mounting Basic dynamic load rating Basic static load rating Allowable
Shaft mm dimension C C0 rotational
dia. da speed(2)
Mass With dust cover Mass Mass With dust cover Mass (1) Radial Axial Radial Axial
mm
(Ref.) (Ref.) (Ref.) (Ref.) Fw D D1 D2 L H l1 rs min d i Min.
g g g g mm N N N N min-1

10 NAX 1023 38.5 NAX 1023Z 40 ─ ─ ─ ─ 10 19 24 25 23 9 6.5 0.3 10 18 8 230 10 000 9 190 11 100 9 500
─ ─ ─ ─
12 NAX 1223
NAX 1523
43.5
47.5
NAX 1223Z 45.5
NAX 1523Z 48.5 ─ ─ ─ ─
12
15
21
24
26 27
28 29
23
23
9 6.5 0.3
9 6.5 0.3
12
15
20
23
9 250
12 300
9 670
9 930
11 200
14 900
11 100
12 200
9 000
8 500
G
15 ─ ─ ─ ─ 54
NBX 1523 NBX 1523Z 55 15 24 28 29 23 9 6.5 0.3 15 26 12 300 10 200 14 900 23 900 14 000
NAX 1725 54 NAX 1725Z 56 ─ ─ ─ ─ 17 26 30 31 25 9 8 0.3 17 25 12 900 10 800 16 300 14 500 8 500
17 ─ ─ ─ ─ 61
NBX 1725 NBX 1725Z 63 17 26 30 31 25 9 8 0.3 17 28 12 900 11 400 16 300 28 600 13 000
NAX 2030 85.5 NAX 2030Z 89 ─ ─ ─ ─ 20 30 35 36 30 10 10.5 0.3 20 29 17 600 14 200 25 400 19 700 7 500
20 ─ ─ ─ ─ 94
NBX 2030 NBX 2030Z 97.5 20 30 35 36 30 10 10.5 0.3 20 33 17 600 19 000 25 400 48 700 11 000
NAX 2530 131 NAX 2530Z 135 ─ ─ ─ ─ 25 37 42 43 30 11 9.5 0.6 25 35 20 000 19 600 32 100 29 700 7 000
25 ─ ─ ─ ─ 143
NBX 2530 NBX 2530Z 147 25 37 42 43 30 11 9.5 0.6 25 40 20 000 22 700 32 100 60 700 9 000
NAX 3030 145 NAX 3030Z 151 ─ ─ ─ ─ 30 42 47 48 30 11 9.5 0.6 30 40 25 100 20 400 40 100 33 600 6 500
30 ─ ─ ─ ─ 160
NBX 3030 NBX 3030Z 166 30 42 47 48 30 11 9.5 0.6 30 45 25 100 27 400 40 100 81 000 8 000
NAX 3530 169 NAX 3530Z 176 ─ ─ ─ ─ 35 47 52 53 30 12 9 0.6 35 45 26 900 21 200 46 200 37 600 6 000
35 ─ ─ ─ ─ 186
NBX 3530 NBX 3530Z 193 35 47 52 53 30 12 9 0.6 35 50 26 900 29 100 46 200 91 100 7 000
NAX 4032 219 NAX 4032Z 227 ─ ─ ─ ─ 40 52 60 61 32 13 10 0.6 40 52 29 400 26 900 54 100 50 000 5 500
40 ─ ─ ─ ─ NBX 4032 240 NBX 4032Z 248 40 52 60 61 32 13 10 0.6 40 57 29 400 41 700 54 100 133 000 6 000
NAX 4532 264 NAX 4532Z 273 ─ ─ ─ ─ 45 58 65 66.5 32 14 9 0.6 45 57 31 000 27 900 60 200 55 100 5 000
45 ─ ─ ─ ─ NBX 4532 293 NBX 4532Z 302 45 58 65 66.5 32 14 9 0.6 45 62 31 000 40 800 60 200 133 000 5 500
NAX 5035 287 NAX 5035Z 297 ─ ─ ─ ─ 50 62 70 71.5 35 14 10 0.6 50 62 42 200 28 800 83 400 60 100 4 500
50 ─ ─ ─ ─ 315
NBX 5035 NBX 5035Z 325 50 62 70 71.5 35 14 10 0.6 50 67 42 200 43 300 83 400 148 000 5 000
NAX 6040 417 NAX 6040Z 454 ─ ─ ─ ─ 60 72 85 86.5 40 17 12 1 60 75 47 500 41 400 103 000 89 700 4 000
60 ─ ─ ─ ─ 501
NBX 6040 NBX 6040Z 538 60 72 85 86.5 40 17 12 1 60 82 47 500 64 600 103 000 224 000 4 000
70 NAX 7040 555 NAX 7040Z 606 ─ ─ ─ ─ 70 85 95 96.5 40 18 11 1 70 85 55 500 43 100 120 000 101 000 3 500

Notes(1)　　 Minimum allowable value of chamfer dimension r

 　　 (2)　　 Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 70% of this value is allowable in the
NAX series, and a maximum of 25% of this value is allowable in the NBX series.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
G5 1mm=0.03937inch
G6
 COMBINED TYPE NEEDLE ROLLER BEARINGS
Needle Roller Bearings with Thrust Ball Bearing With Inner Ring
Needle Roller Bearings with Thrust Roller Bearing With Inner Ring L L
H l1 H l1

r r

r r1 r
r1
B B

D2

D1
D1

Fw

Fw

D2
D

db
da
D
di

di
d

d
NAXI NAXI … Z NBXI NBXI … Z

Shaft dia. 7 − 60mm

Identification number Boundary dimensions Standard mounting Basic dynamic load rating Basic static load rating Allowable Assembled inner ring
Shaft mm dimensions
mm
C C0 rotational
dia. speed(2)
Mass With dust cover Mass Mass With dust cover Mass (1) (1) da db Radial Axial Radial Axial
mm
(Ref.) (Ref.) (Ref.) (Ref.) d D D1 D2 L B H l1 rs min r1s min Fw d i Min.
g g g g N N N N min-1

7 NAXI 723 43.5 NAXI 723Z 45 ─ ─ ─ ─ 7 19 24 25 23 16 9 6.5 0.3 0.2 10 10 18   9 8 230 10 000 9 190 11 100 9 500 LRT 71016
─ ─ ─ ─
9 NAXI 923 49.5 NAXI 923Z 51.5
NAXI 1223 55.5 NAXI 1223Z 56.5 ─ ─ ─ ─
9 21 26
12 24 28
27
29
23 16
23 16.5
9 6.5 0.3 0.3 12 12 20 11
9 6.5 0.3 0.3 15 15 23 14 12 300 9 930
9 250 9 670 11 200
14 900
11 100 9 000 LRT 91216
12 200 8 500 LRT 121516
G
12 ─ ─ ─ ─ NBXI 1223 62 NBXI 1223Z 63 12 24 28 29 23 16.5 9 6.5 0.3 0.3 15 15 26 14 12 300 10 200 14 900 23 900 14 000 LRT 121516
NAXI 1425 63.5 NAXI 1425Z 65.5 ─ ─ ─ ─ 14 26 30 31 25 17 9 8 0.3 0.3 17 17 25 16 12 900 10 800 16 300 14 500 8 500 LRT 141717
14 ─ ─ ─ ─ NBXI 1425 70.5 NBXI 1425Z 72.5 14 26 30 31 25 17 9 8 0.3 0.3 17 17 28 16 12 900 11 400 16 300 28 600 13 000 LRT 141717
NAXI 1730 99 NAXI 1730Z 103 ─ ─ ─ ─ 17 30 35 36 30 20.5 10 10.5 0.3 0.3 20 20 29 19 17 600 14 200 25 400 19 700 7 500 LRT 172020
17 ─ ─ ─ ─ NBXI 1730 108 NBXI 1730Z 111 17 30 35 36 30 20.5 10 10.5 0.3 0.3 20 20 33 19 17 600 19 000 25 400 48 700 11 000 LRT 172020
NAXI 2030 159 NAXI 2030Z 163 ─ ─ ─ ─ 20 37 42 43 30 20.5 11 9.5 0.6 0.3 25 25 35 24 20 000 19 600 32 100 29 700 7 000 LRT 202520
20 ─ ─ ─ ─ NBXI 2030 171 NBXI 2030Z 175 20 37 42 43 30 20.5 11 9.5 0.6 0.3 25 25 40 24 20 000 22 700 32 100 60 700 9 000 LRT 202520
NAXI 2530 179 NAXI 2530Z 185 ─ ─ ─ ─ 25 42 47 48 30 20.5 11 9.5 0.6 0.3 30 30 40 29 25 100 20 400 40 100 33 600 6 500 LRT 253020
25 ─ ─ ─ ─ NBXI 2530 194 NBXI 2530Z 200 25 42 47 48 30 20.5 11 9.5 0.6 0.3 30 30 45 29 25 100 27 400 40 100 81 000 8 000 LRT 253020
NAXI 3030 208 NAXI 3030Z 215 ─ ─ ─ ─ 30 47 52 53 30 20 12 9 0.6 0.3 35 35 45 34 26 900 21 200 46 200 37 600 6 000 LRT 303520
30 ─ ─ ─ ─ NBXI 3030 225 NBXI 3030Z 232 30 47 52 53 30 20 12 9 0.6 0.3 35 35 50 34 26 900 29 100 46 200 91 100 7 000 LRT 303520
NAXI 3532 265 NAXI 3532Z 273 ─ ─ ─ ─ 35 52 60 61 32 20 13 10 0.6 0.3 40 40 52 39 29 400 26 900 54 100 50 000 5 500 LRT 354020
35 ─ ─ ─ ─ NBXI 3532 286 NBXI 3532Z 294 35 52 60 61 32 20 13 10 0.6 0.3 40 40 57 39 29 400 41 700 54 100 133 000 6 000 LRT 354020
NAXI 4032 315 NAXI 4032Z 324 ─ ─ ─ ─ 40 58 65 66.5 32 20 14 9 0.6 0.3 45 45 57 44 31 000 27 900 60 200 55 100 5 000 LRT 404520
40 ─ ─ ─ ─ NBXI 4032 344 NBXI 4032Z 353 40 58 65 66.5 32 20 14 9 0.6 0.3 45 45 62 44 31 000 40 800 60 200 133 000 5 500 LRT 404520
NAXI 4535 358 NAXI 4535Z 368 ─ ─ ─ ─ 45 62 70 71.5 35 25 14 10 0.6 0.3 50 50 62 49 42 200 28 800 83 400 60 100 4 500 LRT 455025
45 ─ ─ ─ ─ NBXI 4535 386 NBXI 4535Z 396 45 62 70 71.5 35 25 14 10 0.6 0.3 50 50 67 49 42 200 43 300 83 400 148 000 5 000 LRT 455025
NAXI 5040 582 NAXI 5040Z 619 ─ ─ ─ ─ 50 72 85 86.5 40 25.5 17 12 1 1 60 60 75 59 47 500 41 400 103 000 89 700 4 000 LRT 506025
50 ─ ─ ─ ─ NBXI 5040 666 NBXI 5040Z 703 50 72 85 86.5 40 25.5 17 12 1 1 60 60 82 59 47 500 64 600 103 000 224 000 4 000 LRT 506025
60 NAXI 6040 750 NAXI 6040Z 801 ─ ─ ─ ─ 60 85 95 96.5 40 25.5 18 11 1 1 70 70 85 68 55 500 43 100 120 000 101 000 3 500 LRT 607025

Notes(1)　　 Minimum allowable value of chamfer dimension r or r1

 　　  (2)　　 Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 70% of this value is allowable in the
NAXI series, and a maximum of 25% of this value is allowable in the NBXI series.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
G7 1mm=0.03937inch
G8
 COMBINED TYPE NEEDLE ROLLER BEARINGS
Needle Roller Bearings with Angular Contact Ball Bearing
Needle Roller Bearings with Three-point Contact Ball Bearing C
B
C

r r

r r

Fw

Fw

Da

Da
D

d
d

da
da
r r
r r

NATA59 NATB59

Shaft dia. 15 − 70mm

Identification number Boundary dimensions Standard mounting dimensions Basic dynamic load rating Basic static load rating Allowable
Shaft mm mm C C0 rotational
dia. speed(2)
Angular contact type Mass Three-point contact type Mass da Da Radial Axial Radial Axial
mm
(Ref.) (Ref.) d D C B rs min(1) Fw
g g Min. Max. N N N N min-1

15 NATA 5902 50.5 NATB 5902 53 15 28 18 20 0.3 20 17 26 7 710 1 900 10 200 2 920 20 000
17
20
NATA 5903 55.5
NATA 5904 111
NATB 5903 58.5
NATB 5904 115
17
20
30
37
18
23
20
25
0.3
0.3
22
25
19
22
28
35
8 220
14 300
2 050
3 810
11 500
18 400
3 340
6 110
18 000
16 000
G
25 NATA 5905 131 NATB 5905 136 25 42 23 25 0.3 30 27 40 15 800 4 300 22 100 7 520 13 000
30 NATA 5906 151 NATB 5906 157 30 47 23 25 0.3 35 32 45 17 700 4 550 26 800 8 460 11 000
35 NATA 5907 250 NATB 5907 260 35 55 27 30 0.6 42 39 51 24 000 4 890 42 100 9 870 9 500
40 NATA 5908 355 NATB 5908 375 40 62 30 34 0.6 48 44 58 30 600 5 350 60 400 11 800 8 500
45 NATA 5909 410 NATB 5909 435 45 68 30 34 0.6 55 49 64 32 600 5 450 68 500 12 700 7 000
50 NATA 5910 420 NATB 5910 445 50 72 30 34 0.6 58 54 68 33 600 5 660 72 500 13 600 7 000
55 NATA 5911 585 NATB 5911 615 55 80 34 38 1 63 60 75 39 500 10 400 74 400 24 700 6 500
60 NATA 5912 625 NATB 5912 660 60 85 34 38 1 68 65 80 41 800 10 700 82 200 26 700 6 000
65 NATA 5913 665 NATB 5913 710 65 90 34 38 1 75 70 85 43 800 11 000 90 200 28 700 5 500
70 NATA 5914 1 070 NATB 5914 1 130 70 100 40 45 1 80 75 95 56 400 13 500 127 000 35 000 5 000

Notes(1)　　 Minimum allowable value of chamfer dimension r

 　 　 (2)　　 Allowable rotational speed applies to oil lubrication. For grease lubrication, a maximum of 60% of this value is allowable.
Remarks1.　The outer ring has an oil groove and an oil hole.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
G9 1mm=0.03937inch
G10
 ■ Structure and Features Shapes of Inner Rings
Inner Rings are heat-treated and finished by
grinding to a high degree of accuracy. In the case of
needle roller bearings, normally, the shafts are heat-
treated and finished by grinding, and used as the
raceway surfaces. However, when it is impossible to
●Inner Rings for Shell Type Needle Roller Bearings make shaft surfaces according to the specified sur-
●Inner Rings for General Usage face hardness or surface roughness, inner rings are
used.
Inner rings include those for Shell Type Needle Roller
Bearings and those for general use and are available
in a variety of dimensions. When shafts move axially Gentle taper relief
or seals are used adjacent to bearings, wide inner
rings can be selected.
Inner rings can also be used economically as bush-
ings without requiring any additional machining.

■ Types
For Inner Rings, the types shown in Table 1 are avail-
able.

Table 1.1 Inner Rings for Shell Type Needle Roller Bearings
Small chamfer

Series Model codes of assembled bearings

TA … Z，TLA … Z
Metric series IRT
H
TAM，TLAM，YT，YTL
BA … Z，BHA … Z
Inch series IRB BAM，BHAM，YB，YBH
Remark　For Inner Rings for Shell Type Needle Roller Bearings
with Seal, please consult .

Table 1.2 Inner Rings for General Usage

Series Model codes of assembled bearings

Gentle taper relief

RNA 49，RNA 69
LRT RNA 48，TAF，TR
Metric series RNAF，NAX，NBX
RNA 49 … UU，RNA 69 … UU
LRTZ
GTR
LRB BR
Inch series
LRBZ … B BR … UU

Small chamfer

H1 H2
■ Identification number Table 2 Tolerances for inner ring Table 5 Tolerances of outside diameter of inner ring unit: μ m
■ Fit
The identification number of Inner Rings consists of a Model code Tolerance Model code Tolerance The recommended fits between Inner Rings and
model code and dimensions. An example is shown shafts are shown in Table 22 on page A42.
IRT JIS Class 0 IRT g5
below.
LRT，LRTZ (See the table 12, page A31) IRB      0 〜− 13

Example of identification number IRB Based on Table 3 LRT，LRTZ Based on Table 6 ■ Oil Hole
LRB LRB，LRBZ … B Based on Table 7
The number of oil holes is shown in Table 8.
Based on Table 4
LRBZ … B When Inner Rings with an oil hole are especially
Model code Dimensions
Remark Tolerances of outside diameter of inner ring are
　　　　based on Table 5. Table 7 Tolerances of outside diameters of LRB and LRBZ … B unit: μ m required for a model without an oil hole, attach an
LRT 20 24 20 Nominal outside diameter "OH" to the end of the identification number when
Table 3 Tolerances of IRB unit: μ m
of inner ring Tolerance ordering.
Type of inner ring d ∆dmp ∆Bs Kia mm
Nominal inside diameter Single plane Deviation of a Radial runout of
Example: LRT  202420  OH
Over Incl. High Low
Bore diameter of inner ring of inner ring mean bore single inner ring assembled For Inner Rings with multiple oil holes, please consult
（20mm） mm diameter deviation width bearing inner ring
− 18.034 − 13 − 23 .
Outside diameter of inner ring Over Incl. High Low High Low Max. 18.034 25.908 − 18 − 30
（24mm） 2.5 10 0 − 13 0 − 250 10 25.908 30.226 − 23 − 36
10 18 0 − 13 0 − 250 10 Table 8 Number of oil holes
Inner ring width 18 30 0 − 13 0 − 250 13 30.226 35.052 − 23 − 38
Number
（20mm） 35.052 50.038 − 25 − 41
30 50 0 − 13 0 − 250 15 　　　   Bearing type Bore diameter of of oil
50 80 0 − 13 0 − 250 20 50.038 80.010 − 28 − 46 inner ring  d   mm holes

■ Accuracy Table 4 Tolerances of LRB,LRBZ…B unit: μ m

80.010
100.076
100.076
102.108
− 32
− 37
− 56
− 66
For Shell Type Metric series IRT
Needle Roller
Bearings Inch series IRB
0
0
Dimensional accuracy of Inner Rings is based on Table 2.
d ∆dmp ∆Bs Kia LRT 0
Inner Rings for Shell Type Needle Roller Bearings are Nominal inside diameter Single plane Deviation of a Radial runout of Metric series
manufactured so that exact radial internal clearances of inner ring mean bore single inner ring assembled LRTZ 0
For General
                 d ≦ 76.200
diameter deviation width bearing inner ring
can be obtained when assembled with Shell Type mm 1
Usage LRB
Needle Roller Bearings. Inner Rings for General Over Incl. High Low High Low Max. Inch series 76.200＜ d 2
− − 10 − 130
H
Usage produce CN clearance when used in the 19.050 0 0 10 LRBZ … B                 1
assembled bearings shown in Table 1.2. LRB and 19.050 30.162 0 − 13 0 − 130 13
30.162 50.800 0 − 13 0 − 130 15 Remark　Inner rings with an oil hole are provided with an oil
LRBZ … B models produce the radial internal clear- groove.
50.800 82.550 0 − 15 0 − 130 20
ances shown in Table 4 on page D5. 82.550 120.650 0 − 20 0 − 130 25
When clearances other than CN clearance or accura-
cy other than Class 0 are required, please consult
.

Table 6 Tolerances of outside diameters for LRT and LRTZ (When the clearance is CN clearance) unit: μ m
d F F d
Bore diameter of Outside diameter of inner ring　mm Outside diameter of inner ring　mm Bore diameter of
inner ring mm 3＜F≦6 6 ＜ F ≦ 10 10 ＜ F ≦ 18 18 ＜ F ≦ 30 30 ＜ F ≦ 50 50 ＜ F ≦ 80 80 ＜ F ≦ 120 120 ＜ F ≦ 180 180 ＜ F ≦ 250 250 ＜ F ≦ 315 315 ＜ F ≦ 400 400 ＜ F ≦ 500 inner ring mm
Over Incl. High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low Over Incl.
− 24 − 10 − 27 −7 − 23 −4 − 18 0 − 12 − 24
24 30 0 − 12 ＋5 − 4 24 30
30 40 0 − 9 30 40
40 50 −5 − 19 0 − 11 40 50
50 65 − 10 − 21 50 65
65 80 − 10 − 26 − 4 − 17 65 80
80 100 − 14 − 27 80 100
100 120 − 14 − 32 − 7 − 22 100 120
120 140 − 17 − 37 120 140
140 160 − 27 − 52 140 160
160 180 − 25 − 46 160 180
180 200 − 40 − 66 180 200
200 225 − 55 − 86 200 225
225 250 − 54 − 87 225 250
250 280 − 69 − 107 250 280
280 315 − 68 − 107 280 315
315 355 − 83 − 127 315 355
355 400 − 128 − 182 − 122 − 172 355 400
400 450 − 142 − 202 400 450
450 500 − 152 − 222 450 500

1N=0.102kgf=0.2248lbs.
H3 1mm=0.03937inch
H4
 INNER RINGS
Inner Rings for Shell Type Needle Roller Bearings
B

da
d
r

IRT

Shaft dia. 7 − 17mm

Mass Boundary dimensions Standard mounting Assembled bearings Mass Boundary dimensions Standard mounting Assembled bearings
Shaft (Ref.) mm dimension  mm Shaft (Ref.) mm dimension  mm
dia. Identification number dia. Identification number
(1) da TA … Z TLA … Z YT
(1) da TA … Z TLA … Z YT
mm g d F B rs min Min. Max.
(TAM) (TLAM) YTL mm g d F B rs min Min. Max.
(TAM) (TLAM) YTL

IRT 710   3.2 7 10 10.5 0.3 9 9.7 TA 1010Z TLA 1010Z ─ IRT 1515 9.3 15 18 15.5 0.3 17 17.5 TA 1815Z ─ ─
7 IRT 712   3.9 7 10 12.5 0.3 9 9.7 TA 1012Z TLA 1012Z ─ IRT 1516 9.9 15 18 16.5 0.3 17 17.5 ─ TLA 1816Z ─
IRT 715   4.8 7 10 15.5 0.3 9 9.7 TA 1015Z TLA 1015Z ─ IRT 1517 10.5 15 18 17.5 0.3 17 17.5 TA 1817Z ─ ─
IRT 1519 11.7 15 18 19.5 0.3 17 17.5 TA 1819Z ─ ─
IRT 810   5.1 8 12 10.5 0.3 10 11 ─ TLA 1210Z YTL 1210
IRT 1520 12.3 15 18 20.5 0.3 17 17.5 TA 1820Z ─ ─
8 IRT 812   6 8 12 12.5 0.3 10 11 TA 1212Z TLA 1212Z YT   1212
IRT 1525 15.2 15 18 25.5 0.3 17 17.5 TA 1825Z ─ ─
IRT 815   7.5 8 12 15.5 0.3 10 11 TA 1215Z ─ ─
IRT 1012   5.2 10 13 12.5 0.3 12 12.7 ─ TLA 1312Z ─
15 IRT 1516-1
IRT 1520-1
13.6
16.8
15
15
19
19
16.5
20.5
0.3
0.3
17
17
18
18
TA 1916Z
TA 1920Z
─
─
─
─ H
IRT 1012-2   7.2 10 14 12.5 0.3 12 13 ─ TLA 1412Z ─ IRT 1515-2 16.4 15 20 15.5 0.3 17 19 TA 2015Z ─ YT 2015
IRT 1016-2   9.6 10 14 16.5 0.3 12 13 TA 1416Z TLA 1416Z ─ IRT 1520-2 21.5 15 20 20.5 0.3 17 19 TA 2020Z TLA 2020Z YT 202820
IRT 1020-2 11.9 10 14 20.5 0.3 12 13 TA 1420Z ─ ─ TA 202820Z
10 IRT 1010-1   7.9 10 15 10.5 0.3 12 14 TA 1510Z ─ ─ IRT 1525-2 27 15 20 25.5 0.3 17 19 TA 2025Z ─ YT 2025
IRT 1012-1   9.4 10 15 12.5 0.3 12 14 TA 1512Z TLA 1512Z ─ IRT 1530-2 32 15 20 30.5 0.3 17 19 TA 2030Z TLA 2030Z ─
IRT 1015-1 11.7 10 15 15.5 0.3 12 14 TA 1515Z ─ ─
IRT 1716 11.1 17 20 16.5 0.3 19 19.5 ─ TLA 2016Z ─
IRT 1020-1 15.5 10 15 20.5 0.3 12 14 TA 1520Z ─ ─
─ ─ IRT 1720 13.7 17 20 20.5 0.3 19 19.5 TA 2020Z TLA 2020Z YT 202820
IRT 1025-1 19.3 10 15 25.5 0.3 12 14 TA 1525Z
TA 202820Z
IRT 1212   6.1 12 15 12.5 0.3 14 14.5 TA 1512Z TLA 1512Z ─ IRT 1730 20.5 17 20 30.5 0.3 19 19.5 TA 2030Z TLA 2030Z ─
IRT 1216   8.1 12 15 16.5 0.3 14 14.5 ─ TLA 1516Z ─ IRT 1716-1 15.1 17 21 16.5 0.3 19 20 TA 2116Z ─ YT 2116
IRT 1222 11 12 15 22.5 0.3 14 14.5 ─ TLA 1522Z ─ IRT 1720-1 18.8 17 21 20.5 0.3 19 20 TA 2120Z ─ YT 2120
IRT 1212-1   8.5 12 16 12.5 0.3 14 15 ─ TLA 1612Z ─ 17 IRT 1710-2 12.4 17 22 10.5 0.3 19 21 TA 2210Z ─ ─
IRT 1216-1 11.2 12 16 16.5 0.3 14 15 TA 1616Z TLA 1616Z ─ IRT 1715-2 18.3 17 22 15.5 0.3 19 21 TA 2215Z ─ ─
12 ─ ─
IRT 1220-1 13.9 12 16 20.5 0.3 14 15 TA 1620Z IRT 1716-2 19.4 17 22 16.5 0.3 19 21 TA 223016Z TLA 2216Z YT 223016
IRT 1222-1 15.2 12 16 22.5 0.3 14 15 ─ TLA 1622Z ─ IRT 1720-2 24 17 22 20.5 0.3 19 21 TA 2220Z TLA 2220Z YT 223020
IRT 1215-2 13.6 12 17 15.5 0.3 14 16 TA 1715Z ─ YT   1715 TA 223020Z
IRT 1220-2 18 12 17 20.5 0.3 14 16 TA 1720Z ─ ─ IRT 1725-2 30 17 22 25.5 0.3 19 21 TA 2225Z ─ ─
IRT 1225-2 22.5 12 17 25.5 0.3 14 16 TA 1725Z ─ YT   1725 IRT 1730-2 36 17 22 30.5 0.3 19 21 TA 2230Z ─ ─
IRT 1512   7.5 15 18 12.5 0.3 17 17.5 ─ TLA 1812Z ─
15 ─ ─
IRT 1513   8.1 15 18 13.5 0.3 17 17.5 TA 1813Z

Note(1)　 Minimum allowable value of chamfer dimension r Note(1)　 Minimum allowable value of chamfer dimension r
Remark　No oil hole is provided. Remark　No oil hole is provided.

1N=0.102kgf=0.2248lbs.
H5 1mm=0.03937inch
H6
 INNER RINGS
Inner Rings for Shell Type Needle Roller Bearings
B

da
d
r

IRT

Shaft dia. 20 − 45mm

Mass Boundary dimensions Standard mounting Assembled bearings Mass Boundary dimensions Standard mounting Assembled bearings
Shaft (Ref.) mm dimension  mm Shaft (Ref.) mm dimension  mm
dia. Identification number dia. Identification number
(1) da TA … Z TLA … Z YT
(1) da TA … Z TLA … Z YT
mm g d F B rs min Min. Max.
(TAM) (TLAM) YTL mm g d F B rs min Min. Max.
(TAM) (TLAM) YTL

IRT 2016 17.5 20 24 16.5 0.3 22 23 TA 243216Z ─ YT 243216 IRT 3020 40 30 35 20.5 0.6 34 34.5 TA 3520Z TLA 3520Z ─
IRT 2020 22 20 24 20.5 0.3 22 23 TA 2420Z ─ YT 243220 30 IRT 3025 50 30 35 25.5 0.6 34 34.5 TA 3525Z ─ ─
TA 243220Z IRT 3030 60 30 35 30.5 0.6 34 34.5 TA 3530Z ─ ─
IRT 2028 30.5 20 24 28.5 0.3 22 23 TA 2428Z ─ YT 2428
IRT 3220 42.5 32 37 20.5 0.6 36 36.5 TA 3720Z ─ YT 3720
IRT 2010-1 14.3 20 25 10.5 0.3 22 24 TA 2510Z ─ YT 2510
IRT 3230 63.5 32 37 30.5 0.6 36 36.5 TA 3730Z ─ ─
20 IRT 2015-1 21 20 25 15.5 0.3 22 24 TA 2515Z ─ YT 2515
IRT 3215-1 39.5 32 38 15.5 0.6 36 37 TA 3815Z ─ ─
IRT 2020-1
IRT 2025-1
28
34.5
20
20
25
25
20.5
25.5
0.3
0.3
22
22
24
24
TA 2520Z
TA 2525Z
TLA 2520Z
─
YT 2520
YT 2525
32 IRT 3220-1
IRT 3225-1
52
64.5
32
32
38
38
20.5
25.5
0.6
0.6
36
36
37
37
TA 3820Z
TA 3825Z
─
─
─
─
H
IRT 2026-1 36 20 25 26.5 0.3 22 24 ─ TLA 2526Z YTL 2526
IRT 3230-1 77.5 32 38 30.5 0.6 36 37 TA 3830Z ─ ─
IRT 2030-1 41.5 20 25 30.5 0.3 22 24 TA 2530Z ─ ─
IRT 3245-1 115 32 38 45.5 0.6 36 37 TAW 3845Z ─ ─
IRT 2038-1 52.5 20 25 38.5 0.3 22 24 ─ TLAW 2538Z ─
IRT 3515 35 35 40 15.5 0.6 39 39.5 TA 4015Z ─ YT 4015
IRT 2216 19.1 22 26 16.5 0.3 24 25 TA 2616Z ─ YT 2616
IRT 3520 46.5 35 40 20.5 0.6 39 39.5 TA 4020Z TLA 4020Z ─
IRT 2220 24 22 26 20.5 0.3 24 25 TA 2620Z ─ YT 2620
22 35 IRT 3525 58 35 40 25.5 0.6 39 39.5 TA 4025Z ─ YT 4025
IRT 2220-1 37 22 28 20.5 0.3 24 27 TA 2820Z TLA 2820Z YT 2820 ─ ─
IRT 3530 69 35 40 30.5 0.6 39 39.5 TA 4030Z
IRT 2230-1 55.5 22 28 30.5 0.3 24 27 TA 2830Z ─ ─
IRT 3540 91.5 35 40 40.5 0.6 39 39.5 TA 4040Z ─ ─
IRT 2520 26.5 25 29 20.5 0.3 27 28 TA 2920Z ─ YT 2920
IRT 4020 52.5 40 45 20.5 0.6 44 45.5 TA 4520Z TLA 4520Z YT 4520
IRT 2530 40 25 29 30.5 0.3 27 28 TA 2930Z ─ ─
IRT 4025 65.5 40 45 25.5 0.6 44 45.5 TA 4525Z ─ YT 4525
IRT 2515-1 25.5 25 30 15.5 0.3 27 29 TA 3015Z ─ ─ 40
IRT 4030 78.5 40 45 30.5 0.6 44 45.5 TA 4530Z ─ ─
IRT 2520-1 34 25 30 20.5 0.3 27 29 TA 3020Z TLA 3020Z ─
25 IRT 4040 104 40 45 40.5 0.6 44 45.5 TA 4540Z ─ ─
IRT 2525-1 42.5 25 30 25.5 0.3 27 29 TA 3025Z ─ ─
IRT 2526-1 44 25 30 26.5 0.3 27 29 ─ TLA 3026Z ─ IRT 4512 36 45 50 12.5 0.6 49 49.5 TA 5012Z ─ ─
IRT 2530-1 50.5 25 30 30.5 0.3 27 29 TA 3030Z ─ ─ IRT 4515 44.5 45 50 15.5 0.6 49 49.5 TA 5015Z ─ ─
IRT 2538-1 64 25 30 38.5 0.3 27 29 ─ TLAW 3038Z ─ IRT 4520 59 45 50 20.5 0.6 49 49.5 TA 5020Z TLA 5020Z ─
45 IRT 4525 73 45 50 25.5 0.6 49 49.5 TA 5025Z TLA 5025Z ─
IRT 2820 29.5 28 32 20.5 0.3 30 31 TA 3220Z ─ YT 3220
28 IRT 4530 87.5 45 50 30.5 0.6 49 49.5 TA 5030Z ─ ─
IRT 2830 44 28 32 30.5 0.3 30 31 TA 3230Z ─ ─
IRT 4540 116 45 50 40.5 0.6 49 49.5 TA 5040Z ─ ─
IRT 3012 24.5 30 35 12.5 0.6 34 34.5 TA 3512Z TLA 3512Z ─ IRT 4545 131 45 50 45.5 0.6 49 49.5 TAW 5045Z ─ ─
30 30 35 15.5 0.6 ─ ─
IRT 3015 30.5 34 34.5 TA 3515Z

Note(1)　 Minimum allowable value of chamfer dimension r Note(1)　 Minimum allowable value of chamfer dimension r
Remark　No oil hole is provided. Remark　No oil hole is provided.

1N=0.102kgf=0.2248lbs.
H7 1mm=0.03937inch
H8
 INNER RINGS
Inner Rings for Shell Type Needle Roller Bearings Inner Rings for Shell Type Needle Roller Bearings Inch Series
B B

da
d

da
d

ra
r

IRT
IRB
Shaft dia. 50 − 60mm Shaft dia. 7.938 − 15.875mm

Mass Boundary dimensions Standard mounting Assembled bearings Mass Boundary dimensions Standard mounting Assembled bearings
Shaft (Ref.) mm dimension  mm Shaft (Ref.) mm(inch) dimensions mm
dia. Identification number dia.
Identification (1)
(1) da TA … Z TLA … Z YT
number da ras max BA … Z BHA … Z YB
d F B rs min Min. Max.
(TAM) (TLAM) YTL
mm
g d F B Min. Max. Max. (BAM) (BHAM) YBH
mm g (inch)

IRT 5020-1 65 50 55 20.5 0.6 54 54.5 TA 5520Z TLA 5520Z ─   7.938

IRB 58 8 7.938（  5 ╱16 ） 12.700（  1╱2 ） 13.08 11.3 11.7 0.3 BA 88Z BHA 88Z YB 88
IRT 5025-1 81 50 55 25.5 0.6 54 54.5 TA 5525Z TLA 5525Z ─ （ 5╱16 ）
IRT 5030-1 96.5 50 55 30.5 0.6 54 54.5 TA 5530Z ─ ─ IRB 68   8.9 9.525（  3╱8 ） 14.288（  9╱16 ） 13.08 12.8 13.2 0.3 BA 98Z BHA 98Z YB 98
IRT 5040-1 128 50 55 40.5 0.6 54 54.5 TA 5540Z ─ ─ 9.525（  3╱8 ） 15.875（  5 ╱8 ） 13.08 12.8 14
─ ─
  9.525 IRB 68-1 12.6 0.3 BA 108Z BHA 108Z YB 108
IRT 5045-1 144 50 55 45.5 0.6 54 54.5 TAW 5545Z YBH 108
─ ─ （ 3╱8 ） 13.2 9.525（  3 ╱8 ） 14.288（  9╱16 ） 19.43 12.8 13.2 0.3
50 IRT 5050-1 160 50 55 50.5 0.6 54 54.5 TAW 5550Z IRB 612 BA 912Z ─ YB 912
IRT 5025
IRT 5030
169
205
50
50
60
60
25.5
30.5
1.5
1.5
58
58
59
59
TA 6025Z
TA 6030Z
─
─
─
─
IRB
IRB
612-1 18.8 9.525（  3 ╱8 ） 15.875（  5 ╱8 ） 19.43 12.8 14 0.3
78 10.1 11.112（  7 ╱16 ） 15.875（  5 ╱8 ） 13.08 14.4 14.8 0.3
BA 1012Z
BA 108Z
BHA 1012Z YB 1012
BHA 108Z YB 108
H
IRT 5040 270 50 60 40.5 1.5 58 59 TA 6040Z ─ ─ YBH 108
11.112
IRT 5045 300 50 60 45.5 1.5 58 59 TAW 6045Z ─ ─ IRB 712 15 11.112（  7 ╱16 ） 15.875（  5 ╱8 ） 19.43 14.4 14.8 0.3 BA 1012Z BHA 1012Z YB 1012
─ ─
（ 7╱16 ） 17.4 11.112（  7╱16 ） 15.875（  5 ╱8 ） ─
IRT 5050 335 50 60 50.5 1.5 58 59 TAW 6050Z IRB 714 22.60 14.4 14.8 0.3 BA 1014Z ─
IRB 716 19.9 11.112（  7 ╱16 ） 15.875（  5 ╱8 ） 25.78 14.4 14.8 0.3 BA 1016Z BHA 1016Z ─
52 IRT 5212 86 52 62 12.5 1.5 60 60.5 TA 6212Z ─ ─
IRB 86   8.5 12.700（  1 ╱2 ） 17.462（ 11╱16 ） 9.90 16.9 16.9 0.3 BA 116Z ─ ─
IRT 5525 185 55 65 25.5 1.5 63 63.5 TA 6525Z ─ ─ IRB 88 11.2 12.700（  1 ╱2 ） 17.462（ 11╱16 ） 13.08 16.9 16.9 0.3 BA 118Z BHA 118Z ─
IRT 5530 220 55 65 30.5 1.5 63 63.5 TA 6530Z ─ ─ IRB 812 16.7 12.700（  1 ╱2 ） 17.462（ 11╱16 ） 19.43 16.9 16.9 0.3 BA 1112Z BHA 1112Z YB 1112
55 ─ ─ ─
IRT 5545 330 55 65 45.5 1.5 63 63.5 TAW 6545Z 12.700 IRB 88-1 15.8 12.700（  1 ╱2 ） 19.050（  3 ╱4 ） 13.08 16.9 17.5 0.6 BA 128Z YB 128
IRT 5550 365 55 65 50.5 1.5 63 63.5 TAW 6550Z ─ ─ （ 1╱2 ） IRB 810-1 19.6 12.700（  1 ╱2 ） 19.050（  3 ╱4 ） 16.25 16.9 17.5 0.6 BA 1210Z ─ YB 1210
IRB 812-1 23.5 12.700（  1 ╱2 ） 19.050（  3 ╱4 ） 19.43 16.9 17.5 0.6 BA 1212Z BHA 1212Z YB 1212
IRT 6025 200 60 70 25.5 1.5 68 68.5 TA 7025Z ─ ─ ─ ─
IRB 814-1 27.5 12.700（  1 ╱2 ） 19.050（  3 ╱4 ） 22.60 16.9 17.5 0.6 BA 1214Z
IRT 6030 240 60 70 30.5 1.5 68 68.5 TA 7030Z ─ ─ ─ ─
60 IRB 816-1 31 12.700（  1 ╱2 ） 19.050（  3 ╱4 ） 25.78 16.9 17.5 0.6 BA 1216Z
IRT 6040 320 60 70 40.5 1.5 68 68.5 TA 7040Z ─ ─
─ ─ IRB 98 17.3 14.288（  9╱16 ） 20.638（ 13╱16 ） 13.08 19 19.6 0.6 BA 138Z BHA 138Z YB 138
IRT 6050 395 60 70 50.5 1.5 68 68.5 TAW 7050Z
IRB 910 21.5 14.288（  9╱16 ） 20.638（ 13╱16 ） 16.25 19 19.6 0.6 BA 1310Z BHA 1310Z YBH 1310
14.288 IRB 912 26 14.288（  9 ╱16 ） 20.638（ 13╱16 ） 19.43 19 19.6 0.6 BA 1312Z BHA 1312Z YBH 1312
（ 9╱16 ） IRB 914 30 14.288（  9╱16 ） 20.638（ 13╱16 ） 22.60 19 19.6 0.6 BA 1314Z ─ ─
IRB 916 34.5 14.288（  9╱16 ） 20.638（ 13╱16 ） 25.78 19 19.6 0.6 BA 1316Z ─ ─
IRB 920 43 14.288（  9 ╱16 ） 20.638（ 13╱16 ） 32.13 19 19.6 0.6 BA 1320Z ─ ─
14.5 15.875（  5 ╱8 ） 22.225（  7 ╱8 ） 9.90 20.7 21.2 0.6 ─ ─
15.875 IRB 106 BA 146Z
IRB 108 18.9 15.875（  5 ╱8 ） 22.225（  7 ╱8 ） 13.08 20.7 21.2 0.6 BA 148Z ─ YB   148
（ 5╱8 ）
IRB 1012 28 15.875（  5 ╱8 ） 22.225（  7 ╱8 ） 19.43 20.7 21.2 0.6 BA 1412Z BHA 1412Z YB   1412

Note(1)　 Minimum allowable value of chamfer dimension r Note(1)　 Maximum allowable fillet corner radius of shaft
Remark　No oil hole is provided. Remark　No oil hole is provided.

1N=0.102kgf=0.2248lbs.
H9 1mm=0.03937inch
H10
 INNER RINGS
Inner Rings for Shell Type Needle Roller Bearings Inch Series
B

da
ra
IRB

Shaft dia. 15.875 − 63.500mm

Mass Boundary dimensions Standard mounting Assembled bearings Mass Boundary dimensions Standard mounting Assembled bearings
Shaft (Ref.) mm(inch) dimensions mm Shaft (Ref.) mm(inch) dimensions mm
dia.
Identification (1) dia.
Identification (1)
number da ras max BA … Z BHA … Z YB
number da ras max BA … Z BHA … Z YB
mm
(inch) g d F B Min. Max. Max. (BAM) (BHAM) YBH
mm
(inch) g d F B Min. Max. Max. (BAM) (BHAM) YBH

15.875 IRB 1014 33 15.875（  5╱8 ） 22.225（  7╱8 ） 22.60 20.7 21.2 0.6 BA 1414Z ─ ─ IRB 188 31.5 28.575（1  1╱8 ） 34.925（1  3╱8 ） 13.08 33.2 33.9 0.6 BA 228Z BHA 228Z YB 228
IRB 1016 37.5 15.875（  5╱8 ） 22.225（  7╱8 ） 25.78 20.7 21.2 0.6 BA 1416Z BHA 1416Z YB   1416 28.575 IRB 1812 47 28.575（1  1╱8 ） 34.925（1  3╱8 ） 19.43 33.2 33.9 0.6 BA 2212Z BHA 2212Z YB 2212
（ 5╱8 ）
IRB 1022 51.5 15.875（  5╱8 ） 22.225（  7╱8 ） 35.30 20.7 21.2 0.6 BA 1422Z ─ ─ （1 1╱8 ） IRB 1816 62.5 28.575（1  1╱8 ） 34.925（1  3╱8 ） 25.78 33.2 33.9 0.6 BA 2216Z BHA 2216Z ─
17.462 IRB 1110 25.5 17.462（ 11╱16 ） 23.812（ 15╱16 ） 16.25 22.3 22.8 0.6 ─ ─ IRB 1820 78 28.575（1  1╱8 ） 34.925（1  3╱8 ） 32.13 33.2 33.9 0.6 BA 2220Z BHA 2220Z YB 2220
BA 1510Z
（ 11╱16 ） IRB 1116 40.5 17.462（ 11╱16 ） 23.812（ 15╱16 ） 25.78 22.3 22.8 0.6 BA 1516Z ─ ─ IRB 2010 43 31.750（1  1╱4 ） 38.100（1  1╱2 ） 16.25 37 37.1 0.6 BA 2410Z ─ ─
31.750 IRB 2014 60 31.750（1  1╱4 ） 38.100（1  1╱2 ） 22.60 37 37.1 0.6 BA 2414Z ─ YB 2414
IRB 128 22 19.050（  3╱4 ） 25.400（1 ） 13.08 23.9 24.4 0.6 BA 168Z BHA 168Z YB 168
（1 1╱4 ） IRB 2016
IRB 1212 33 19.050（  3╱4 ） 25.400（1 ） 19.43 23.9 24.4 0.6 BA 1612Z
YBH   168
BHA 1612Z YB   1612
IRB 2020
68.5
85.5
31.750（1  1╱4 ） 38.100（1  1╱2 ）
31.750（1  1╱4 ） 38.100（1  1╱2 ）
25.78
32.13
37
37
37.1
37.1
0.6
0.6
BA
BA
2416Z
2420Z
─
─
YB 2416
YB 2420 H
19.050 YBH 1612 34.925 IRB 2210 47 34.925（1  3╱8 ） 41.275（1  5╱8 ） 16.25 40.2 40.2 0.6 BA 2610Z ─ YB 2610
（ 3╱4 ） IRB 1214 38.5 19.050（  3╱4 ） 25.400（1 ） 22.60 23.9 24.4 0.6 BA 1614Z BHA 1614Z ─ （1 3╱8 ） IRB 2220 93.5 34.925（1  3╱8 ） 41.275（1  5╱8 ） 32.13 40.2 40.2 0.6 BA 2620Z ─ ─
IRB 1216 43.5 19.050 （  3╱4 ） 25.400（1 ） 25.78 23.9 24.4 0.6 BA 1616Z BHA 1616Z YB   1616 36.512 99
IRB 2316 36.512（1   7╱16 ）44.450（1   3╱4 ） 25.78 42.5 43.2 0.6 BA 2816Z ─ ─
YBH 1616 （1 7╱16 ）
IRB 1220 54.5 19.050（  3╱4 ） 25.400（1 ） 32.13 23.9 24.4 0.6 BA 1620Z BHA 1620Z ─
IRB 2412 62 38.100（1  1╱2 ） 44.450（1  3╱4 ） 19.43 43.3 43.4 0.6 BA 2812Z ─ ─
20.638 IRB 1316 20.638（ 13╱16 ） 25.400（1 ） 25.78 24.9 24.9 0.6 BA 1616Z BHA 1616Z YB   1616 ─
34
38.100 IRB 2416 81 38.100（1  1╱2 ） 44.450（1  3╱4 ） 25.78 43.3 43.4 0.6 BA 2816Z YB 2816
（ 13╱16 ） YBH 1616 IRB 2424 121 38.100（1  1╱2 ） 44.450（1  3╱4 ） 38.48 43.3 43.4 0.6 BA 2824Z BHA 2824Z ─
（1 1╱2 ） ─ ─
IRB 148 25 22.225（  7╱8 ）
28.575（1  1╱8 ） 13.08 27 27.5 0.6 BA 188Z ─ YB   188 IRB 248-1 64 38.100（1  1╱2 ） 47.625（1  7╱8 ） 13.08 44.5 45.5 1 BA 308Z
22.225 IRB 1412 37.5 22.225（  7╱8 ）
28.575（1  1╱8 ） 19.43 27 27.5 0.6 BA 1812Z BHA 1812Z YB   1812 IRB 2410-1 79.5 38.100（1  1╱2 ） 47.625（1  7╱8 ） 16.25 44.5 45.5 1 BA 3010Z ─ ─
（ 7╱8 ） IRB 1416 50 22.225（  7╱8 ）
28.575（1  1╱8 ） 25.78 27 27.5 0.6 BA 1816Z BHA 1816Z YB   1816 41.275 IRB 2616 136 41.275（1  5╱8 ） 50.800（2 ） 25.78 47.5 48.5 1 BA     3216Z ─ ─
IRB 1420 62.5 22.225（  7╱8 ）
28.575（1  1╱8 ） 32.13 27 27.5 0.6 BA 1820Z BHA 1820Z ─ （1 5╱8 ） IRB 2628 235 41.275（1  5╱8 ） 50.800（2 ） 44.83 47.5 48.5 1 BAW 3228Z ─ ─
IRB 168 28.5 25.400（1 ）31.750（1  1╱4 ） 13.08 30 30.7 0.6 BA 208Z BHA 208Z ─ 42.862 ─ ─
）31.750（1  1╱4 ） 16.25 ─ IRB 2720 146 42.862（1  11╱16）50.800（2 ） 32.13 48.5 49.5 0.6 BA     3220Z
IRB 1610 35.5 25.400（1 30 30.7 0.6 BA 2010Z YB   2010 （1 11╱16 ） ─ ─
IRB 1612 42.5 25.400（1 ）31.750（1  1╱4 ） 19.43 30 30.7 0.6 BA 2012Z BHA 2012Z YB   2012
25.400 IRB 1616 ）31.750（1  1╱4 ） 25.78
47.625 IRB 3016 100 47.625（1  7╱8 ） 53.975（2  1╱8 ） 25.78 52.9 52.9 0.6 BA     3416Z ─ ─
56 25.400（1 30 30.7 0.6 BA 2016Z BHA 2016Z YB   2016
（1） IRB 1620 70 25.400（1 ）31.750（1  1╱4 ） 32.13 30 30.7 0.6 BA 2020Z BHA 2020Z ─ （1 7╱8 ） IRB 3024 149 47.625（1  7╱8 ） 53.975（2  1╱8 ） 38.48 52.9 52.9 0.6 BA     3424Z ─ ─
IRB 168-1 36.5 25.400（1 ）33.338（1  5╱16 ） 13.08 30 32.1 0.6 BA 218Z ─ ─ 57.150 ─ ─
IRB 3616 183 57.150（2  1╱4 ） 66.675（2  5╱8 ） 25.78 63.5 64.5 1 BA     4216Z
IRB 1610-1 45.5 25.400（1 ）33.338（1  5╱16 ） 16.25 30 32.1 0.6 BA 2110Z ─ ─ （2 1╱4 ） ─ ─
IRB 1612-1 54.5 25.400（1 ）33.338（1  5╱16 ） 19.43 30 32.1 0.6 BA 2112Z ─ ─
63.500 IRB 4016 131 63.500（2  1╱2 ） 69.850（2  3╱4 ） 25.78 68.7 68.8 0.6 BA     4416Z ─ ─
（2 1╱2 ） IRB 4020 164 63.500（2  1╱2 ） 69.850（2  3╱4 ） 32.13 68.7 68.8 0.6 BA     4420Z ─ ─

Note(1)　 Maximum allowable fillet corner radius of shaft Note(1)　 Maximum allowable fillet corner radius of shaft
Remark　No oil hole is provided. Remark　No oil hole is provided.

1N=0.102kgf=0.2248lbs.
H11 1mm=0.03937inch
H12
 INNER RINGS
Inner Rings for General Usage
B B

r r

da
d

d
r r

LRT LRTZ

Shaft dia. 5 − 20mm

Mass Boundary dimensions Standard mounting Assembled bearings Mass Boundary dimensions Standard mounting Assembled bearings
Shaft (Ref.) mm dimension mm Shaft (Ref.) mm dimension mm
dia. Identification number dia. Identification number da
(1) da (1)
mm g d F B rs min Min. Max.
mm g d F B rs min Min. Max.

LRT 5710 ─ 1.4 5 7 10 0.15   6.2 6.7 RNA 495 LRT 121622 ─ 14.5 12 16 22 0.3 14 15 RNA 6901
─ 12
  5 LRT 5812 2.8 5 8 12 0.2   6.6 7.7 TAF 81512 ─ LRTZ 121623 15.5 12 16 23 0.3 14 15 RNA 6901 UU
LRT 5816 ─ 3.8 5 8 16 0.2   6.6 7.7 TAF 81516
14 LRT 141717 ─ 9.5 14 17 17 0.3 16 16.5 NAX 1725 NBX 1725
LRT 6810 ─ 1.7 6 8 10 0.15   7.2 7.7 RNA 496
LRT 151916 ─ 12.5 15 19 16 0.3 17 18 TAF 192716
─
  6 LRT 6912
3.2 6 9 12 0.2   7.6 8.7 TAF 91612
LRT 151920 ─ 16 15 19 20 0.3 17 18 TAF 192720
LRT 6916 ─ 4.3 6 9 16 0.2   7.6 8.7 TAF 91616
LRT 61010 ─ 3.9 6 10 10 0.3   8 9.7 RNAF 101710
LRT 152012
LRT 152013
─
─
12
13.5
15
15
20
20
12
13
0.3
0.3
17
17
19
19
RNAF 203212
RNA 4902 RNAF 202813 H
LRT 7910 ─ 1.9 7 9 10 0.15   8.2 8.7 RNA 497 ─ LRTZ 152014 14.5 15 20 14 0.3 17 19 RNA 4902 UU
─ 15
LRT 152020 ─
  7 LRT 71012
3.6 7 10 12 0.2   8.6 9.7 TAF 101712 21.5 15 20 20.5 0.3 17 19 TR 203320
LRT 71012-1 ─ 3.6 7 10 12 0.3   9 9.7 RNAF 102012 ─ LRTZ 152020 21.5 15 20 20.5 0.3 17 19 GTR 203320
LRT 71016 ─ 4.9 7 10 16 0.2   8.6 9.7 TAF 101716 NAX 1023 LRT 152023 ─ 24 15 20 23 0.3 17 19 RNA 6902
  8 LRT 81011 ─ 2.4 8 10 11 0.2   9.6 9.9 RNA 498 ─ LRTZ 152024 25 15 20 24 0.3 17 19 RNA 6902 UU
LRT 152026 ─ 28 15 20 26 0.3 17 19 RNAFW 202826
LRT 91211 ─ 3.1 9 12 11 0.3 11 11.5 RNA 499
  9 LRT 91212 ─ 4.5 9 12 12 0.3 11 11.5 TAF 121912 RNAF 122212
LRT 172020 ─ 13.5 17 20 20.5 0.3 19 19.5 NAX 2030 NBX 2030
─ LRT 172116 ─ 14.5 17 21 16 0.3 19 20 TAF 212916
LRT 91216 6 9 12 16 0.3 11 11.5 TAF 121916 NAX 1223
LRT 172120 ─ 18 17 21 20 0.3 19 20 TAF 212920
LRT 101412 ─ 7 10 14 12 0.3 12 13 RNAF 142612 LRT 172213 ─ 15.5 17 22 13 0.3 19 21 RNA 4903 RNAF 223013
LRT 101413 ─ 7.5 10 14 13 0.3 12 13 RNA 4900 RNAF 142213 ─ LRTZ 172214 16.5 17 22 14 0.3 19 21 RNA 4903 UU
10 ─ LRTZ 101414 8.2 10 14 14 0.3 12 13 RNA 4900 UU LRT 172216 ─ 19 17 22 16 0.3 19 21 RNAF 223516
LRT 101416 ─ 17
9 10 14 16 0.3 12 13 TAF 142216 LRT 172223 ─ 26.5 17 22 23 0.3 19 21 RNA 6903
LRT 101420 ─ 11.5 10 14 20 0.3 12 13 TAF 142220 RNAFW142220 ─ LRTZ 172224 28 17 22 24 0.3 19 21 RNA 6903 UU
LRT 121516 ─ 8 12 15 16.5 0.3 14 14.5 NAX 1523 NBX 1523 LRT 172225 ─ 30 17 22 25.5 0.3 19 21 TR 223425
LRT 121612 ─ 8.5 12 16 12 0.3 14 15 RNAF 162812 ─ LRTZ 172225 30 17 22 25.5 0.3 19 21 GTR 223425
LRT 121613 ─ 8.5 12 16 13 0.3 14 15 RNA 4901 RNAF 162413 LRT 172226 ─ 31 17 22 26 0.3 19 21 RNAFW 223026
12 ─ LRT 172232 ─ 38 17 22 32 0.3 19 21 RNAFW 223532
LRTZ 121614 9.6 12 16 14 0.3 14 15 RNA 4901 UU
LRT 121616 ─ 10.5 12 16 16 0.3 14 15 TAF 162416 LRT 202416 ─ 16.5 20 24 16 0.3 22 23 TAF 243216
LRT 121620 ─ 20
13.5 12 16 20 0.3 14 15 TAF 162420 RNAFW162420 LRT 202420 ─ 20.5 20 24 20 0.3 22 23 TAF 243220

Note(1)　 Minimum allowable value of chamfer dimension r Note(1)　 Minimum allowable value of chamfer dimension r
Remark　No oil hole is provided. Remark　No oil hole is provided.

1N=0.102kgf=0.2248lbs.
H13 1mm=0.03937inch
H14
 INNER RINGS
Inner Rings for General Usage
B B

r r

da
d

d
r r

LRT LRTZ

Shaft dia. 20 − 32mm

Mass Boundary dimensions Standard mounting Assembled bearings Mass Boundary dimensions Standard mounting Assembled bearings
Shaft (Ref.) mm dimension mm Shaft (Ref.) mm dimension mm
dia. Identification number dia. Identification number
(1) da (1) da
mm g d F B rs min Min. Max.
mm g d F B rs min Min. Max.

LRT 202516 ─ 22 20 25 16 0.3 22 24 RNAF 253716 ─ LRTZ 253031 51 25 30 31 0.3 27 29 RNA 6905 UU
─ 25
LRT 202517 23 20 25 17 0.3 22 24 RNA 4904 RNAF 253517 LRT 253032 ─ 54 25 30 32 0.3 27 29 RNAFW 304232
─ LRTZ 202518 24 20 25 18 0.3 22 24 RNA 4904 UU
─
LRT 283217 24.5 28 32 17 0.3 30 31 RNA 49 / 28
LRT 202520 ─ 28 20 25 20.5 0.3 22 24 TR 253820 NAX 2530
─ LRTZ 283218 25.5 28 32 18 0.3 30 31 RNA 49 / 28 UU
NBX 2530
LRT 283220 ─ 28.5 28 32 20 0.3 30 31 TAF 324220
─ LRTZ 202520 28 20 25 20.5 0.3 22 24 GTR 253820 28
─
20 LRT 283230 43 28 32 30 0.3 30 31 RNA 69 / 28 TAF 324230
LRT 202525
─
─ 35
LRTZ 202525 35 20
20 25
25
25.5
25.5
0.3
0.3
22
22
24
24
TR 253825
GTR 253825
─
─
LRTZ 283230
LRTZ 283231
43
44
28
28
32
32
30.5
31
0.3
0.3
30
30
31
31
GTR 324530
RNA 69 / 28 UU
H
LRT 202526 ─ 36 20 25 26 0.3 22 24 RNAFW 253526
LRT 202530 ─ 40.5 20 25 30 0.3 22 24 RNA 6904 LRT 303516 ─ 31.5 30 35 16 0.3 32 34 RNAF 354716
─ LRTZ 202531 41.5 20 25 31 0.3 22 24 RNA 6904 UU LRT 303517 ─ 33.5 30 35 17 0.3 32 34 RNA 4906 RNAF 354517
LRT 202532 ─ 44 20 25 32 0.3 22 24 RNAFW 253732 ─ LRTZ 303518 35 30 35 18 0.3 32 34 RNA 4906 UU
LRT 303520 ─ 38.5 30 35 20 0.3 32 34 TAF 354520 NAX 3530
LRT 222616 ─ 17.5 22 26 16 0.3 24 25 TAF 263416
NBX 3530
LRT 222620 ─ 24 22 26 20 0.3 24 25 TAF 263420
30 LRT 303526 ─ 52 30 35 26 0.3 32 34 RNAFW 354526
LRT 222817 ─ 30.5 22 28 17 0.3 24 27 RNA 49 / 22
22 LRT 303530 ─ 59 30 35 30 0.3 32 34 RNA 6906 TAF 354530
─ LRTZ 222818 32 22 28 18 0.3 24 27 RNA 49 / 22 UU
LRT 303530-1 ─ 59 30 35 30.5 0.3 32 34 TR 354830
LRT 222830 ─ 55 22 28 30 0.3 24 27 RNA 69 / 22
─ LRTZ 303530 59 30 35 30.5 0.3 32 34 GTR 354830
─ LRTZ 222831 55 22 28 31 0.3 24 27 RNA 69 / 22 UU
─ LRTZ 303531 61 30 35 31 0.3 32 34 RNA 6906 UU
LRT 252920 ─ 25 25 29 20 0.3 27 28 TAF 293820 LRT 303532 ─ 64 30 35 32 0.3 32 34 RNAFW 354732
LRT 252930 ─ 38 25 29 30 0.3 27 28 TAF 293830
LRT 323720 ─ 43.5 32 37 20 0.3 34 36 TAF 374720
LRT 253016 ─ 28 25 30 16 0.3 27 29 RNAF 304216
LRT 323730 ─ 63 32 37 30 0.3 34 36 TAF 374730
LRT 253017 ─ 28.5 25 30 17 0.3 27 29 RNA 4905 RNAF 304017
LRT 323830 ─ 77 32 38 30.5 0.6 36 37 TR 385230
─ LRTZ 253018 29.5 25 30 18 0.3 27 29 RNA 4905 UU
25 ─ LRTZ 323830 77 32 38 30.5 0.6 36 37 GTR 385230
LRT 253020 ─ 34 25 30 20.5 0.3 27 29 NAX 3030 NBX 3030 32
─ 20 0.6
LRT 324020 69 32 40 36 39 RNA 49/32
LRT 253025 ─ 42 25 30 25.5 0.3 27 29 TR 304425
─ LRTZ 324021 72.5 32 40 21 0.6 36 39 RNA 49/32 UU
─ LRTZ 253025 42 25 30 25.5 0.3 27 29 GTR 304425
LRT 324036 ─ 123 32 40 36 0.6 36 39 RNA 69/32
LRT 253026 ─ 44.5 25 30 26 0.3 27 29 RNAFW 304026
─ LRTZ 324037 130 32 40 37 0.6 36 39 RNA 69/32 UU
LRT 253030 ─ 49 25 30 30 0.3 27 29 RNA 6905

Note(1)　 Minimum allowable value of chamfer dimension r Note(1)　 Minimum allowable value of chamfer dimension r
Remark　No oil hole is provided. Remark　No oil hole is provided.

1N=0.102kgf=0.2248lbs.
H15 1mm=0.03937inch
H16
 INNER RINGS
Inner Rings for General Usage
B B

r r

da
d

d
r r

LRT LRTZ

Shaft dia. 35 − 50mm

Mass Boundary dimensions Standard mounting Assembled bearings Mass Boundary dimensions Standard mounting Assembled bearings
Shaft (Ref.) mm dimension mm Shaft (Ref.) mm dimension mm
dia. Identification number dia. Identification number
(1) da (1) da
mm g d F B rs min Min. Max.
mm g d F B rs min Min. Max.

LRT 354017 ─ 39 35 40 17 0.3 37 39 RNAF 405017 LRT 424720 ─ 54 42 47 20 0.3 44 46 TAF 475720
LRT 354020 ─ 46 35 40 20 0.3 37 39 TAF 405020 RNAF 405520 LRT 424730 ─ 81 42 47 30 0.3 44 46 TAF 475730
42
NAX 4032 NBX 4032 LRT 424830 ─ 100 42 48 30.5 0.6 46 47 TR 486230
─ LRTZ 354020 46 35 40 20.5 0.6 39 39.5 GTR 405520 ─ LRTZ 424830 100 42 48 30.5 0.6 46 47 GTR 486230
LRT 354030 ─ 67 35 40 30 0.3 37 39 TAF 405030
LRT 455020 ─ 58 45 50 20 0.3 47 49 RNAF 506220
LRT 354034 ─ 78 35 40 34 0.3 37 39 RNAFW 405034
LRT 455025 ─ 71 45 50 25 0.3 47 49 TAF 506225 NAX 5035
35 LRT 354040
LRT 354220
─
─
95
65
35
35
40
42
40
20
0.3
0.6
37
39
39 RNAFW 405540
41 RNA 4907
LRT 455030 ─ 90 45 50 30.5 0.6
NBX 5035
49 49.5 TR 506430
H
─ LRTZ 354221 67 35 42 21 0.6 39 41 RNA 4907 UU
─ LRTZ 455030 90 45 50 30.5 0.6 49 49.5 GTR 506430
LRT 354230 ─ 97 35 42 30.5 0.6 39 41 TR 425630
LRT 455035 ─ 95 45 50 35 0.3 47 49 TAF 506235
─ LRTZ 354230 100 35 42 30.5 0.6 39 41 GTR 425630
─
45 LRT 455040 115 45 50 40 0.3 47 49 RNAFW 506240
LRT 354236 ─ 120 35 42 36 0.6 39 41 RNA 6907
LRT 455222 ─ 88 45 52 22 0.6 49 51 RNA 4909
─ LRTZ 354237 120 35 42 37 0.6 39 41 RNA 6907 UU
─ LRTZ 455223 93 45 52 23 0.6 49 51 RNA 4909 UU
LRT 384320 ─ 47.5 38 43 20 0.3 40 42 TAF 435320 LRT 455240 ─ 165 45 52 40 0.6 49 51 RNA 6909
38
LRT 384330 ─ 72 38 43 30 0.3 40 42 TAF 435330 ─ LRTZ 455241 170 45 52 41 0.6 49 51 RNA 6909 UU
LRT 455520 ─ 120 45 55 20 1 50 54 RNAF 557220
LRT 404517 ─ 44.5 40 45 17 0.3 42 44 RNAF 455517
─ 51 40 45 20 0.3 42 44 LRT 455540 ─ 245 45 55 40 1 50 54 RNAFW 557240
LRT 404520 TAF 455520 RNAF 456220
NAX 4532 NBX 4532 LRT 505520 ─ 63 50 55 20 0.3 52 54 RNAF 556820
LRT 404530 ─ 77 40 45 30 0.3 42 44 TAF 455530 LRT 505525 ─ 77 50 55 25 0.3 52 54 TAF 556825
LRT 404530-1 ─ 77 40 45 30.5 0.6 44 44.5 TR 455930 LRT 505535 ─ 110 50 55 35 0.3 52 54 TAF 556835
─ LRTZ 404530 77 40 45 30.5 0.6 44 44.5 GTR 455930 LRT 505540 ─ 130 50 55 40 0.3 52 54 RNAFW 556840
40
LRT 404534 ─ 88 40 45 34 0.3 42 44 RNAFW 455534 LRT 505822 ─ 116 50 58 22 0.6 54 57 RNA 4910
LRT 404540 ─ 105 40 45 40 0.3 42 44 RNAFW 456240 50 ─ LRTZ 505823 118 50 58 23 0.6 54 57 RNA 4910 UU
LRT 404822 ─ 93 40 48 22 0.6 44 47 RNA 4908 LRT 505840 ─ 210 50 58 40 0.6 54 57 RNA 6910
─ LRTZ 404823 95 40 48 23 0.6 44 47 RNA 4908 UU ─ LRTZ 505841 215 50 58 41 0.6 54 57 RNA 6910 UU
LRT 404840 ─ 165 40 48 40 0.6 44 47 RNA 6908 LRT 505845 ─ 235 50 58 45.5 1 55 57 TR 587745
─ LRTZ 404841 170 40 48 41 0.6 44 47 RNA 6908 UU ─ LRTZ 505845 235 50 58 45.5 1 55 57 GTR 587745
LRT 506020 ─ 135 50 60 20 1 55 59 RNAF 607820

Note(1)　 Minimum allowable value of chamfer dimension r Note(1)　 Minimum allowable value of chamfer dimension r
Remark　No oil hole is provided. Remark　No oil hole is provided.

1N=0.102kgf=0.2248lbs.
H17 1mm=0.03937inch
H18
 INNER RINGS
Inner Rings for General Usage
B B

r r

da
d

d
r r

LRT LRTZ

Shaft dia. 50 − 80mm

Mass Boundary dimensions Standard mounting Assembled bearings Mass Boundary dimensions Standard mounting Assembled bearings
Shaft (Ref.) 　mm dimension mm Shaft (Ref.) mm dimension mm
dia. Identification number dia. Identification number
(1) da (1) da
mm g d F B rs min Min. Max.
mm g d F B rs min Min. Max.

─ ─
50 LRT 506025 LRT 657530
165 50 60 25.5 1 55 59 NAX 6040 NBX 6040 260 65 75 30 1.5 73 73.5 RNAF 759530
65
LRT 506040 ─ 265 50 60 40 1 55 59 RNAFW 607840 LRT 657560 ─ 520 65 75 60 1.5 73 73.5 RNAFW 759560
LRT 556025 ─ 88 55 60 25 0.3 57 59 TAF 607225 LRT 708025 ─ 225 70 80 25 1 75 78 TAF 809525
LRT 556035 ─ 120 55 60 35 0.3 57 59 TAF 607235 LRT 708030 ─ 275 70 80 30 1 75 78 RNA 4914
LRT 556238 ─ 190 55 62 38.5 1 60 60.5 TR 628138 LRT 708030-1 ─ 275 70 80 30 1.5 78 78.5 RNAF 8010030
─ LRTZ 556238 190 55 62 38.5 1 60 60.5 GTR 628138 ─ LRTZ 708031 275 70 80 31 1 75 78 RNA 4914 UU
55
LRT 556325
─
─
LRTZ 556326
145
150
55
55
63
63
25
26
1
1
60
60
61
61
RNA 4911
RNA 4911 UU
70
LRT 708035
LRT 708054
─
─
310
490
70
70
80
80
35
54
1
1
75
75
78
78
TAF 809535
RNA 6914
H
LRT 556345 ─ 255 55 63 45 1 60 61 RNA 6911 ─ LRTZ 708055 500 70 80 55 1 75 78 RNA 6914 UU
─ LRTZ 556346 260 55 63 46 1 60 61 RNA 6911 UU LRT 708060 ─ 560 70 80 60 1.5 78 78.5 RNAFW 8010060
LRT 556530 ─ 220 55 65 30 1.5 63 63.5 RNAF 658530
─ 350 45.5 1 81
LRT 758345 75 83 80 TR 8310845
LRT 556560 ─ 435 55 65 60 1.5 63 63.5 RNAFW 658560
─ LRTZ 758345 350 75 83 45.5 1 80 81 GTR 8310845
LRT 606825 ─ 150 60 68 25 0.6 64 66 TAF 688225 LRT 758525 ─ 240 75 85 25 1 80 83 TAF 8510525
LRT 606825-1 ─ 150 60 68 25 1 65 66 RNA 4912 LRT 758530 ─ 290 75 85 30 1 80 83 RNA 4915
─ LRTZ 606826 160 60 68 26 1 65 66 RNA 4912 UU 75 LRT 758530-1 ─ 290 75 85 30 1.5 83 83.5 RNAF 8510530
LRT 606835 ─ 210 60 68 35 0.6 64 66 TAF 688235 ─ LRTZ 758531 300 75 85 31 1 80 83 RNA 4915 UU
LRT 606845 ─ 275 60 68 45 1 65 66 RNA 6912 LRT 758535 ─ 335 75 85 35 1 80 83 TAF 8510535
60 ─ LRTZ 606846 280 60 68 46 1 65 66 RNA 6912 UU LRT 758554 ─ 520 75 85 54 1 80 83 RNA 6915
LRT 607025 ─ 195 60 70 25.5 1 65 68 NAX 7040 ─ LRTZ 758555 530 75 85 55 1 80 83 RNA 6915 UU
LRT 607030 ─ 240 60 70 30 1.5 68 68.5 RNAF 709030
LRT 809025 ─ 255 80 90 25 1 85 88 TAF 9011025
LRT 607045 ─ 355 60 70 45.5 1 65 68 TR 708945
LRT 809030 ─ 310 80 90 30 1 85 88 RNA 4916
─ LRTZ 607045 360 60 70 45.5 1 65 68 GTR 708945
LRT 809030-1 ─ 310 80 90 30 1.5 88 88.5 RNAF 9011030
LRT 607060 ─ 480 60 70 60 1.5 68 68.5 RNAFW 709060
80 ─ LRTZ 809031 315 80 90 31 1 85 88 RNA 4916 UU
LRT 657225 ─ 145 65 72 25 1 70 70.5 RNA 4913 LRT 809035 ─ 355 80 90 35 1 85 88 TAF 9011035
─ LRTZ 657226 150 65 72 26 1 70 70.5 RNA 4913 UU LRT 809054 ─ 550 80 90 54 1 85 88 RNA 6916
65 LRT 657245 ─ 255 65 72 45 1 70 70.5 RNA 6913 ─ LRTZ 809055 560 80 90 55 1 85 88 RNA 6916 UU
─ LRTZ 657246 265 65 72 46 1 70 70.5 RNA 6913 UU
LRT 657335 ─ 235 65 73 35 1 70 71 TAF 739035
Note(1)　 Minimum allowable value of chamfer dimension r Note(1)　 Minimum allowable value of chamfer dimension r
Remark　No oil hole is provided. Remark　No oil hole is provided.

1N=0.102kgf=0.2248lbs.
H19 1mm=0.03937inch
H20
 INNER RINGS
Inner Rings for General Usage
B B

r r

da
d

d
r r

LRT LRTZ

Shaft dia. 85 − 140mm

Mass Boundary dimensions Standard mounting Assembled bearings Mass Boundary dimensions Standard mounting Assembled bearings
Shaft (Ref.) mm dimension mm Shaft (Ref.) mm dimension mm
dia. Identification number dia. Identification number
(1) da (1) da
mm g d F B rs min Min. Max.
mm g d F B rs min Min. Max.

LRT 859350 ─ 440 85 93 50.5 1 90 91 TR 9311850 LRT 10011030 ─ 380 100 110 30 1 105 108 TAF 11013030
─ LRTZ 859350 440 85 93 50.5 1 90 91 GTR 9311850 LRT 10011040 ─ 500 100 110 40 1 105 108 TAF 11013040
LRT 859526 ─ 280 85 95 26 1 90 93 TAF 9511526 LRT 10011050 ─ 640 100 110 50.5 1.5 108 108.5 TR 11013550
100
LRT 859530 ─ 330 85 95 30 1.5 93 93.5 RNAF 9511530 ─ LRTZ 10011050 640 100 110 50.5 1.5 108 108.5 GTR 11013550
LRT 859536 ─ 390 85 95 36 1 90 93 TAF 9511536 LRT 10011540 ─ 770 100 115 40 1.1 106.5 113 RNA 4920
85 LRT 859545 ─ 490 85 95 45.5 1.5 93 93.5 TR 9512045 ─ LRTZ 10011541 780 100 115 41 1.1 106.5 113 RNA 4920 UU
─
LRT 8510035
LRTZ 859545 490
─ 575
85
85
95
100
45.5
35
1.5
1.1
93 93.5
91.5 98
GTR 9512045
RNA 4917 105
LRT 10511550
─
─
LRTZ 10511550
670 105 115 50.5 1.5 113
670 105 115 50.5 1.5 113
113.5 TR 11515350
113.5 GTR 11515350
H
─ LRTZ 8510036 605 85 100 36 1.1 91.5 98 RNA 4917 UU
LRT 8510063 ─ 1 040 85 100 63 1.1 91.5 98 RNA 6917 LRT 11012030 ─ 410 110 120 30 1 115 118 RNA 4822
─ LRTZ 8510064 1 060 85 100 64 1.1 91.5 98 RNA 6917 UU 110 LRT 11012540 ─ 840 110 125 40 1.1 116.5 123 RNA 4922
─ LRTZ 11012541 870 110 125 41 1.1 116.5 123 RNA 4922 UU
LRT 9010026 ─ 295 90 100 26 1 95 98 TAF 10012026
LRT 9010030 ─ 355 90 100 30 1.5 98 98.5 RNAF 10012030 LRT 12013030 ─ 450 120 130 30 1 125 128 RNA 4824
LRT 9010036 ─ 415 90 100 36 1 95 98 TAF 10012036 120 LRT 12013545 ─ 1 030 120 135 45 1.1 126.5 133 RNA 4924
LRT 9010050 ─ 580 90 100 50.5 1.5 98 98.5 TR 10012550 ─ LRTZ 12013546 1 050 120 135 46 1.1 126.5 133 RNA 4924 UU
90 ─ LRTZ 9010050 580 90 100 50.5 1.5 98 98.5 GTR 10012550 LRT 12514060 ─ 1 460 125 140 60.5 1.5 133 138 TR 14017860
LRT 9010535 ─ 610 90 105 35 1.1 96.5 103 RNA 4918 125
─ LRTZ 12514060 1 460 125 140 60.5 1.5 133 138 GTR 14017860
─ LRTZ 9010536 630 90 105 36 1.1 96.5 103 RNA 4918 UU
LRT 9010563 ─ 1 100 90 105 63 1.1 96.5 103 RNA 6918 LRT 13014535 ─ 860 130 145 35 1.1 136.5 143 RNA 4826
─ LRTZ 9010564 1 120 90 105 64 1.1 96.5 103 RNA 6918 UU 130 LRT 13015050 ─ 1 670 130 150 50 1.5 138 148 RNA 4926
─ LRTZ 13015051 1 720 130 150 51 1.5 138 148 RNA 4926 UU
LRT 9510526 ─ 315 95 105 26 1 100 103 TAF 10512526
LRT 9510536 ─ 430 95 105 36 1 100 103 TAF 10512536 LRT 13515060 ─ 1 560 135 150 60.5 1.5 143 148 TR 15018860
135
LRT 9511035 ─ 650 95 110 35 1.1 101.5 108 RNA 4919 ─ LRTZ 13515060 1 560 135 150 60.5 1.5 143 148 GTR 15018860
95
─ LRTZ 9511036 660 95 110 36 1.1 101.5 108 RNA 4919 UU LRT 14015535 ─ 930 140 155 35 1.1 146.5 153 RNA 4828
LRT 9511063 ─ 1 160 95 110 63 1.1 101.5 108 RNA 6919 140 LRT 14016050 ─ 1 790 140 160 50 1.5 148 158 RNA 4928
─ LRTZ 9511064 1 180 95 110 64 1.1 101.5 108 RNA 6919 UU ─ LRTZ 14016051 1 830 140 160 51 1.5 148 158 RNA 4928 UU

Note(1)　 Minimum allowable value of chamfer dimension r Note(1)　 Minimum allowable value of chamfer dimension r
Remark　No oil hole is provided. Remark　No oil hole is provided.

1N=0.102kgf=0.2248lbs.
H21 1mm=0.03937inch
H22
 INNER RINGS
Inner Rings for General Usage
B

da
r

LRT

Shaft dia. 150 − 440mm

Mass Boundary dimensions Standard mounting Assembled bearings Mass Boundary dimensions Standard mounting Assembled bearings
Shaft (Ref.) mm dimension mm Shaft (Ref.) mm dimension mm
dia. Identification number dia. Identification number
(1) da (1) da
mm g d F B rs min Min. Max.
mm g d F B rs min Min. Max.

LRT 15016540 ─ 1 130 150 165 40 1.1 156.5 163 RNA 4830 LRT 34037080 ─ 10 200 340 370 80 2.1 351 367 RNA 4868
150 ─ 340 ─
LRT 15017060 2 290 150 170 60 2 159 168 RNA 4930 LRT 340380118 20 300 340 380 118 3 353 377 RNA 4968
LRT 16017540 ─ 1 200 160 175 40 1.1 166.5 173 RNA 4832 LRT 36039080 ─ 10 800 360 390 80 2.1 371 387 RNA 4872
160 ─ 360 ─
LRT 16018060 2 440 160 180 60 2 169 178 RNA 4932 LRT 360400118 21 500 360 400 118 3 373 397 RNA 4972
LRT 17018545 ─ 1 420 170 185 45 1.1 176.5 183 RNA 4834 LRT 380415100 ─ 16 700 380 415 100 2.1 391 412 RNA 4876
170 ─
380 ─
LRT 17019060
LRT 18019545 ─
2 580 170 190
1 500 180 195
60 2 179 188
45 1.1 186.5 193
RNA 4934
RNA 4836
LRT 380430140
400 LRT 400450140 ─
33 900 380 430 140 4
35 600 400 450 140 4
396
416
427
447
RNA 4976
RNA 4980
H
180 ─
LRT 18020569 3 950 180 205 69 2 189 203 RNA 4936 420 LRT 420470140 ─ 37 300 420 470 140 4 436 467 RNA 4984
LRT 19021050 ─ 2 380 190 210 50 1.5 198 208 RNA 4838 ─
190 440 LRT 440490160 44 100 440 490 160 4 456 487 RNA 4988
LRT 19021569 ─ 4 200 190 215 69 2 199 213 RNA 4938
LRT 20022050 ─ 2 520 200 220 50 1.5 208 218 RNA 4840
200 ─
LRT 20022580 5 000 200 225 80 2.1 211 223 RNA 4940
LRT 22024050 ─ 2 750 220 240 50 1.5 228 238 RNA 4844
220 ─
LRT 22024580 5 500 220 245 80 2.1 231 243 RNA 4944
LRT 24026560 ─ 4 530 240 265 60 2 249 262 RNA 4848
240 ─
LRT 24026580 6 000 240 265 80 2.1 251 262 RNA 4948
LRT 26028560 ─ 4 930 260 285 60 2 269 282 RNA 4852
260 ─
LRT 260290100 9 900 260 290 100 2.1 271 287 RNA 4952
LRT 28030569 ─ 6 050 280 305 69 2 289 302 RNA 4856
280 ─
LRT 280310100 10 600 280 310 100 2.1 291 307 RNA 4956
LRT 30033080 ─ 9 100 300 330 80 2.1 311 327 RNA 4860
300 ─
LRT 300340118 18 000 300 340 118 3 313 337 RNA 4960
LRT 32035080 ─ 9 600 320 350 80 2.1 331 347 RNA 4864
320 ─
LRT 320360118 19 200 320 360 118 3 333 357 RNA 4964

Note(1)　 Minimum allowable value of chamfer dimension r Note(1)　 Minimum allowable value of chamfer dimension r
Remark　No oil hole is provided. Remark　No oil hole is provided.

1N=0.102kgf=0.2248lbs.
H23 1mm=0.03937inch
H24
 INNER RINGS
Inner Rings for General Usage Inch Series
B B

da
d
F

ra
LRB LRBZ … B

Shaft dia. 9.525 − 22.225mm

Mass Boundary dimensions Standard mounting Assembled bearings

Shaft (Ref.) mm(inch) dimensions　mm
dia. Identification number (1)
da ras max
mm
(inch) g
d F B Min. Max. Max.

  9.525 LRB 61012 ─ 18.5 9.525（  3╱8 ） 15.875（  5╱8 ） 19.300 14 14.5 0.6 BR 101812
（ 3╱8 ） ─ LRBZ 61016 B 25 9.525（  3╱8 ） 15.875（  5╱8 ） 25.650 14 14.5 0.6 BR 101816UU
─ 12.700（  1╱2 ） 19.050（  3╱4 ） 19.300
12.700 LRB 81212 23.5 17.5 18 1 BR 122012
LRB 81216 ─ 31 12.700（  1╱2 ） 19.050（  3╱4 ） 25.650 17.5 18 1 BR 122016
（ 1╱2 ）
─ LRBZ 81216 B 31 12.700（  1╱2 ） 19.050（  3╱4 ） 25.650 17.5 18 0.6 BR 122016UU
15.875（  5╱8 ） 22.225（  7╱8 ） 19.300
15.875 LRB 101412
（ 5╱8 ）
LRB 101416
─
─
28
37.5 15.875（  5╱8 ） 22.225（  7╱8 ） 25.650
21
21
21.2
21.2
1
1
BR
BR
142212
142216 H
─ LRBZ 101416 B 37.5 15.875（  5╱8 ） 22.225（  7╱8 ） 25.650 21 21.2 0.6 BR 142216UU
─ 33 19.050（  3╱4 ） 25.400（1 ） 19.300 24
19.050 LRB 121612 24.4 1 BR 162412
LRB 121616 ─ 44 19.050（  3╱4 ） 25.400（1 ） 25.650 24 24.4 1 BR 162416
（ 3╱4 ） 19.050（  3╱4 ） 25.400（1
─ LRBZ 121616 B 44 ） 25.650 24 24.4 0.6 BR 162416UU
─ 50 22.225（  7╱8 ） 28.575（1  1╱8 ） 25.650 27
22.225 LRB 141816 27.5 1 BR 182616
LRB 141820 ─ 62 22.225（  7╱8 ） 28.575（1  1╱8 ） 32.000 27 27.5 1 BR 182620
（ 7╱8 ） 22.225（  7╱8 ） 28.575（1  1╱8 ） 32.000
─ LRBZ 141820 B 62 27 27.5 0.6 BR 182620UU

Note(1)　 Maximum allowable fillet corner radius of shaft

Remark　LRB and LRBZ…B are provided with an oil groove and an oil hole.

1N=0.102kgf=0.2248lbs.
H25 1mm=0.03937inch
H26
 INNER RINGS
Inner Rings for General Usage Inch Series
B B

da
d
F

ra
LRB LRBZ … B

Shaft dia. 25.400 − 38.100mm

Mass Boundary dimensions Standard mounting Assembled bearings

Shaft (Ref.) mm(inch) dimensions　mm
dia. Identification number (1)
da ras max
mm
(inch) g
d F B Min. Max. Max.

─ 56 25.400（1 ）31.750（1  1╱4 ） 25.65030.5 30.7 1

25.400 LRB 162016 BR 202816
─ 72 25.400（1 ）31.750（1  1╱4 ）32.000 30.5 30.7 1
（1） LRB 162020
BR 202820
─ LRBZ 162020 B 72 25.400（1 ）31.750（1  1╱4 ）32.000 30.5 30.7 0.6 BR 202820UU

28.575 LRB 182216 ─ 63 28.575（1  1╱8 ）34.925（1  3╱8 ） 25.650 33.5 33.9 1 BR 223016
LRB 182220 ─ 77 28.575（1  1╱8 ）34.925（1  3╱8 ） 32.000 33.5 33.9 1 BR 223020
（1 1╱8 ）
─ LRBZ 182220 B 77 28.575（1  1╱8 ）34.925（1  3╱8 ） 32.000 33.5 33.9 0.6 BR 223020UU

31.750 LRB 202416 ─ 71 31.750（1  1╱4 ）38.100（1  1╱2 ） 25.650 37 37.1 1.5 BR 243316 H
LRB 202420 ─ 86 31.750（1  1╱4 ）38.100（1  1╱2 ） 32.000 37 37.1 1.5 BR 243320
（1 1╱4 ）
─ LRBZ 202420 B 86 31.750（1  1╱4 ）38.100（1  1╱2 ） 32.000 37 37.1 0.6 BR 243320UU

34.925 LRB 222616 ─ 77 34.925（1  3╱8 ）41.275（1  5╱8 ） 25.650 40.2 40.2 1.5 BR 263516
LRB 222620 ─ 96 34.925（1  3╱8 ）41.275（1  5╱8 ） 32.000 40.2 40.2 1.5 BR 263520
（1 3╱8 ）
─ LRBZ 222620 B 96 34.925（1  3╱8 ）41.275（1  5╱8 ） 32.000 40.2 40.2 0.6 BR 263520UU
LRB 242816 ─ 80 38.100（1  1╱2 ）44.450（1  3╱4 ） 25.650 43.3 43.4 1.5 BR 283716
38.100 LRB 242820 ─ 100 38.100（1  1╱2 ）44.450（1  3╱4 ） 32.000 43.3 43.4 1.5 BR 283720 BR 283820
LRB 243020 ─ 155 38.100（1  1╱2 ）47.625（1  7╱8 ） 32.000 43.3 45 1.5 BR 303920
（1 1╱2 ）
─ LRBZ 242820 B 100 38.100（1  1╱2 ）44.450（1  3╱4 ） 32.000 43.3 43.4 0.6 BR 283720UU
─ LRBZ 243020 B 160 38.100（1  1╱2 ）47.625（1  7╱8 ） 32.000 43.3 45 1 BR 303920UU

Note(1)　 Maximum allowable fillet corner radius of shaft

Remark　LRB and LRBZ…B are provided with an oil groove and an oil hole.

1N=0.102kgf=0.2248lbs.
H27 1mm=0.03937inch
H28
 INNER RINGS
Inner Rings for General Usage Inch Series
B B

da
d
F

ra
LRB LRBZ … B

Shaft dia. 41.275 − 63.500mm

Mass Boundary dimensions Standard mounting Assembled bearings

Shaft (Ref.) mm(inch) dimensions　mm
dia. Identification number (1)
da ras max
mm
(inch) g d F B Min. Max. Max.

41.275 LRB 263216 ─ 135 41.275（1  5╱8 ）50.800（2 ） 25.650 48 49 1.5 BR 324116
LRB 263220 ─ 170 41.275（1  5╱8 ）50.800（2 ） 32.000 48 49 1.5 BR 324120
（1 5╱8 ）
─ LRBZ 263220 B 170 41.275（1  5╱8 ）50.800（2 ） 32.000 48 49 1 BR 324120UU

44.450 LRB 283624 ─ 300 44.450（1  3╱4 ）57.150（2  1╱4 ） 38.350 52.5 55 1.5 BR 364824
LRB 283628 ─ 345 44.450（1  3╱4 ）57.150（2  1╱4 ） 44.700 52.5 55 1.5 BR 364828
（1 3╱4 ）
─ LRBZ 283628 B 345 44.450（1  3╱4 ）57.150（2  1╱4 ） 44.700 52.5 55 1.5 BR 364828UU

50.800 LRB 324024 ─ 335 50.800（2 ）63.500（2  1╱2 ） 38.350 58 61 2 BR 405224 H

50.800（2  1╱2
─ 390 ）63.500（2
（2） LRB 324028 ） 44.700 58 61 2 BR 405228
─ LRBZ 324028 B 390 50.800（2 ）63.500（2  1╱2 ） 44.700 58 61 1.5 BR 405228UU

57.150 LRB 364424 ─ 375 57.150（2  1╱4 ）69.850（2  3╱4 ） 38.350 65 67 2 BR 445624
LRB 364428 ─ 440 57.150（2  1╱4 ）69.850（2  3╱4 ） 44.700 65 67 2 BR 445628
（2 1╱4 ）
─ LRBZ 364428 B 440 57.150（2  1╱4 ）69.850（2  3╱4 ） 44.700 65 67 1.5 BR 445628UU

63.500 LRB 404824 ─ 410 63.500（2  1╱2 ）76.200（3 ） 38.350 71 73 2 BR 486024

LRB 404828 ─ 480 63.500（2  1╱2 ）76.200（3 ） 44.700 71 73 2 BR 486028
（2 1╱2 ）
─ LRBZ 404828 B 480 63.500（2  1╱2 ）76.200（3 ） 44.700 71 73 1.5 BR 486028UU

Note(1)　 Maximum allowable fillet corner radius of shaft

Remark　LRB and LRBZ…B are provided with an oil groove and an oil hole.

1N=0.102kgf=0.2248lbs.
H29 1mm=0.03937inch
H30
 INNER RINGS
Inner Rings for General Usage Inch Series
B B

da
d
F

ra
LRB LRBZ … B

Shaft dia. 69.850 − 88.900mm

Mass Boundary dimensions Standard mounting Assembled bearings

Shaft (Ref.) mm(inch) dimensions　mm
dia. Identification number (1)
da ras max
mm
(inch) g d F B Min. Max. Max.

69.850 LRB 445228 ─ 530 69.850（2  3╱4 ）  82.550（3  1╱4 ） 44.700 77 79 2 BR 526828
LRB 445232 ─ 600 69.850（2  3╱4 ）  82.550（3  1╱4 ） 51.050 77 79 2 BR 526832
（2 3╱4 ）
─ LRBZ 445228 B 530 69.850（2  3╱4 ）  82.550（3  1╱4 ） 44.700 77 79 1.5 BR 526828UU
76.200 LRB 485632 ─ 640 76.200（3 ）  88.900（3  1╱2 ） 51.050 83.5 86 2 BR 567232
（3） ─ LRBZ 485632 B 640 76.200（3 ）  88.900（3  1╱2 ） 51.050 83.5 86 1.5 BR 567232UU
82.550（3  1╱4 ）  95.250（3  3╱4 ） 51.050 91
H
82.550 LRB 526032 ─ 690 93 2.5 BR 607632
（3 1╱4 ） ─ LRBZ 526032 B 690 82.550（3  1╱4 ）  95.250（3  3╱4 ） 51.050 91 93 1.5 BR 607632UU
88.900
LRB 566432 ─ 750 88.900（3  1╱2 ）101.600（4 ） 51.050 97 99 2.5 BR 648032
（3 1╱2 ）

Note(1)　 Maximum allowable fillet corner radius of shaft

Remark　LRB with inner ring bore diameter d of 76.200 mm or less and LRBZ…B are provided with an oil groove and an oil hole.
Other models are provided with an oil groove and two oil holes.

1N=0.102kgf=0.2248lbs.
H31 1mm=0.03937inch
H32
 ■ Structure and Features
Cam Followers are bearings with a stud incor- high accuracy. They are, therefore, used widely for
porating needle rollers in a thick walled outer ring. machine tools, industrial robots, electronic devices,
These bearings are designed for outer ring rotation, and OA equipment.
and have superior rotational performance with a Stainless steel made Cam Followers are superior in
●Standard Type Cam Followers ●Easy Mounting Type Cam Followers small coefficient of friction and high load capacity. corrosion resistance and suitable for applications in
As studs already have threads or steps, they are easy environments where oil cannot be used or water
●Stainless Steel Made Cam Followers ●Cam Follower G to mount. splashed, and in clean rooms.

●Double Hex Hole Cam Followers ●C-Lube Cam Followers Cam Followers are follower bearings for cam mecha-
nisms and linear motions and have high rigidity and
●Solid Eccentric Stud Type Cam Followers ●Miniature Type Cam Followers
●Eccentric Type Cam Followers ●Stainless Steel Made Miniature Cam Followers
●Thrust Disk Type Cam Followers ●Thrust Disk Type Miniature Cam Followers Structure of Cam Followers

●Centralized Lubrication Type Cam Followers ●Cylindrical Roller Cam Followers Standard Type Cam Follower(1) Thrust Disk Type Cam Follower(1) Cam Follower G(2)

Seal Seal
Cage Thrust disk Cage

Cage

Stud Stud Stud

Side plate Side plate Side plate
Needle roller Needle roller Needle roller
Outer ring Outer ring Outer ring

C-Lube Cam Follower(3) Miniature Type Cam Follower Cylindrical Roller Cam Follower

Seal I
Thrust disk Cage Shield plate
Cage

Stud
Stud Stud
Side plate Side plate Side plate
Needle roller Needle roller Cylindrical roller
Outer ring Outer ring Outer ring

Note(1)　In case of the stud diameter (d1) 5 to 10mm, a re-greasing fitting is provided in the stud head hex hole. The stud diameter (d1) 12 to
30mm, a grease nipple is provided in the stud head hex hole.
(2)　If needed, contact .
(3)　Thermosetting solid-type lubricant fills inner space of the bearing.

I1 I2
■ Types Standard Type Cam Followers
These are the basic type bearings in Cam Follower
Easy Mounting Type Cam Followers
These bearings have a stepped tapered portion on the
For Cam Followers, the types shown in Table 1 are available. series. Models with stud diameters ranging from 3 to 30 stud. When mounting the Cam Follower, it is easy to fix
mm are prepared, and are suitable for a wide range of its location by tightening a set screw to the stepped por-
Table 1 Type of Cam Followers applications. tion. Thus, this type is suitable when a large number of
Item With cage Full complement Cam Followers are used in a machine such as a pallet
Bearing Model Crowned outer ring Cylindrical outer ring Crowned outer ring Cylindrical outer ring Double Hex Hole Cam Followers changer.
The sockets with hexagon hole on both stud ends allow
Shield type CF … B R CF … B CF …VB R CF …VB mounting with a hexagon wrench from either side. Cam Follower G
High carbon With hexagon
Standard Type Cam Taking over the basic performance of Standard Type
steel made hole
Followers Sealed type CF … BUUR CF … BUU CF …VBUUR CF …VBUU Solid Eccentric Stud Type Cam Followers Cam Follower, this cam follower realizes a reasonable
The stud of these bearings is eccentric to the center axis price. As grease is pre-packed, the unit may be used
CF
Stainless With hexagon Shield type CF …FB R CF …FB ─ ─ of the outer ring. Thus, the position of the outer ring in the right after unpacking.
steel made hole Sealed type CF …FBUUR CF …FBUU ─ ─ radial direction in relation to the mating cam guide surface
can easily be adjusted by turning the stud, and the load C-Lube Cam Followers
Double Hex Hole Shield type CFKR… R CFKR CFKR…V R CFKR…V distribution on a number of cam follower outer rings used These bearings are lubricated with a newly developed
High carbon With double on the same cam guide surface can be made uniform. thermosetting solid-type lubricant which fills the inner
Cam Followers
steel made hexagon hole These are eccentric cam followers with a one-piece stud space of the bearing. This lubricant provides long-term
CFKR Sealed type CFKR…UUR CFKR…UU CFKR…VUUR CFKR…VUU
that can be mounted in the same mounting holes as maintenance free.
those for Standard Type Cam Followers.
Solid Eccentric Stud Shield type CFES… B R CFES… B ─ ─ Eccentricity is 0.25 mm 〜 0.6 mm. Miniature Type Cam Followers
High carbon With hexagon
Metric CF series

Type Cam Followers These are compactly designed bearings, incorporating

steel made hole
CFES Sealed type CFES… BUUR CFES… BUU ─ ─ Eccentric Type Cam Followers very thin needle rollers in an outer ring with a small out-
In these bearings, an eccentric collar is assembled with side diameter. They are used in electronic devices, OA
Eccentric Type Cam High carbon With hexagon Shield type CFE … B R CFE … B CFE …VB R CFE …VB the Cam Follower stud, enabling the outer ring to be posi- equipment, small index devices, etc.
Followers
steel made hole Sealed type CFE … BUUR CFE … BUU CFE …VBUUR CFE …VBUU tioned easily in the radial direction against the mating cam
CFE
High carbon With hexagon Shield type CF … WB R ─ ─ ─
guide surface. Cylindrical Roller Cam Followers
Thrust Disk Type Eccentricity is 0.4 〜 1.5 mm. These bearings are full complement type bearings incor-
Cam Followers
steel made hole Sealed type CF … WBUUR ─ ─ ─ porating double rows of full complement cylindrical rollers
Stainless With hexagon Shield type CF …FWB R ─ ─ ─
CF … W Thrust Disk Type Cam Followers in the outer ring, and can withstand large radial loads.
steel made hole Sealed type CF …FWBUUR ─ ─ ─ These bearings have special resin thrust disk washers Additionally, the outer ring is guided by the outer ring
Centralized Lubrication Type superior in wear and heat resistance between the sliding shoulder and the end face of cylindrical rollers to the axial
High carbon With screwdriver
Cam Followers Sealed type CF-RU1 CF-FU1 ─ ─ contact area of outer ring shoulders, stud head and side direction.
steel made slot
CF-RU1, CF-FU1 plate. These disk washers reduce friction and wear due
Easy Mounting Type
Cam Followers
High carbon With hexagon
Sealed type ─ CF-SFU…B ─ ─
to axial loads caused by misalignment, etc. Inch series Cam Followers
Two types, CR and CRH, are available in the Inch series
I
steel made hole
CF-SFU Centralized Lubrication Type Cam Followers Cam Followers. Black oxide film treatment is made on
Cam Follower G High carbon With hexagon These bearings have one or two pipe-threaded holes in CRH models.
Shield type ─ CF … G ─ ─
CF … G steel made hole the stud. Thus, this series is suitable when centralized
C-Lube Cam Followers High carbon With hexagon lubrication is required.
Sealed type CF …WB…/SG ─ ─ ─
CF … WB … /SG steel made hole

Miniature Type Cam

High carbon With hexagon
Shield type ─ CFS ─ CFS　… V
Lubrication method of Hex Head Cam Followers
〈Types〉
Miniature CFS series

steel made hole Standard Type, Double Hex Hole Type, Solid Eccentric Stud Type,
Followers
Stainless With hexagon Eccentric Type, Thrust Disk Type, Easy Mounting Type, Cylindrical Roller Type.
CFS Shield type ─ CFS　…F ─ CFS　… FV
steel made hole
High carbon With hexagon
Thrust Disk Type Miniature Shield type ─ CFS　… W ─ CFS　… WV
Cam Followers steel made hole
Stainless With hexagon (1)
CFS … W Shield type ─ CFS　…FW ─ ─ Stud dia. Stud dia.
steel made hole
Cylindrical Roller Cam Followers High carbon With hexagon
Shield type ─ ─ NUCF… BR ─
NUCF steel made hole
With hexagon Shield type CR … B R CR … B CR …VB R CR …VB
Inch Series Cam
High carbon hole Sealed type CR … BUUR CR … BUU CR …VBUUR CR …VBUU
Followers
steel made With screwdriver Shield type CR … R CR CR …V R CR …V
CR
Inch series

slot Sealed type CR … UUR CR … UU CR …V UUR CR …V UU

With hexagon Shield type ─ ─ CRH …VB R CRH …VB
Inch Series Cam
High carbon hole Sealed type ─ ─ CRH …VBUUR CRH …VBUU
Followers Re-greasing fitting is incorporated in the stud head. Grease nipple is incorporated in the stud head.
steel made With screwdriver Shield type ─ ─ CRH …V R CRH …V
CRH
slot Sealed type ─ ─ CRH …V UUR CRH …V UU Remark : All Easy Mounting Type have a 1way port.
Note (1) Lubrication from both thread side and head part is possible for Double Hex Hole Cam 1N=0.102kgf=0.2248lbs.
I3 Followers only. (2 Way Type) 1mm=0.03937inch
I4
Also, for Double Hex Hole Cam Followers only, a grease nipple is built into the stud head.
■ Internal Structures and Shapes ■ Identification number
The Cam Follower series includes various types, such cylindrical outer ring, type with hexagon hole, type Some examples of the identification number of Cam Followers are shown below. For applicable material symbol,
as the caged type, full complement type, shield type, with screwdriver slot, etc. roller guide method, seal structure and shape of outer ring outside surface, refer dimension table of each series.
sealed type, type with crowned outer ring, type with

Examples of identification number

  Roller guide method 《With cage》 《Full complement》
Example 1 CF 10 V UU R
Cam Followers include the caged type and the full
complement type . The caged type has a small coeffi-
cient of friction and is suitable for high speed rota-
tions, while the full complement type is suitable for
Example 2 CF 10 W B R
heavy loads at low speed rotations.

Example 3 CF 8 W B UU R /SG

Example 4 CFS 3 F V P6
  Seal structure 《Shield type》 《 Sealed type》
Model code
Cam Followers include the shield type and the sealed CF Standard Type Cam Follower
CFKR Double Hex Hole Cam Follower
type. In the shield type, the narrow clearances
CFES Solid Eccentric Stud Type Cam Follower
between the outer ring and the stud flange and CFE Eccentric Type Cam Follower
between the outer ring and the side plate form CF…W Thrust Disk Type Cam Follower
labyrinths . CF-RU1 Centralized Lubrication Type Cam Follower
(With crowned outer ring)
The sealed type incorporates seals in the narrow CF-FU1 Centralized Lubrication Type Cam Follower
(With cylindrical outer ring)
clearances to prevent the penetration of foreign parti-
CF-SFU Easy Mounting Type Cam Follower
cles. CF…G Cam Follower G
CF…WB…/SG C-Lube Cam Follower
CFS Miniature Type Cam Follower
CFS…W Thrust Disk Type Miniature Cam Follower

  Shape of outer ring outside surface 《Crowned outer ring》 《Cylindrical outer ring》 NUCF Cylindrical Roller Cam Follower
CR…B Inch series Cam Follower(With Hexagon socket)
The outside surface of the outer ring of Cam
Followers, which makes direct contact with the mat-
CR
CRH…B
Inch series Cam Follower(With Screw driverslot)
Inch series Cam Follower(With Hexagon socket) I
ing cam guide surface, is either crowned or cylindri- CRH Inch series Cam Follower(With Screw driverslot)

cal. The crowned outer rings are effective in moderat-

Size
ing the edge load due to mounting errors. The cylin- The value indicates a stud diameter. (unit: mm)
drical outer rings have a large contact area with the For Double Hex Hole Cam Followers, the outside diameter of the outer
R

mating cam guide surface, and are suitable for appli- ring is indicated.
In the inch series, the outside diameter of the outerring in units of 1/16
cations in which the applied load is large or the cam inch is indicated.
guide surface hardness is low.
Material
No symbol High carbon steel made
F Stainless steel made

Roller guide method

No symbol With cage type
V Full complement type

Seal structure
No symbol Shield type
UU Sealed type

Shape of outer ring outside surface

R With crowned outer ring
No symbol With cylindrical outer ring

Classification symbol
No symbol Class 0
P6 Class 6 Applicable to
P5 Class 5 Miniature CFS
P4 Class 4 series

I5 I6
■ Accuracy ■ Clearance
The accuracy of Cam Followers is shown in Table 2, The radial internal clearances of Cam Followers are shown in Table 4.
Table 3.1, Table 3.2 and Table 3.3. Cam Followers
with special accuracy are also available. When they
Table 4 Radial internal clearance unit: μ m
are required, please contact .
Identification number（1） Radial internal clearance

Table 2 Tolerances unit: μ m Metric Miniature Cylindrical Roller Cam Followers

Inch series Min. Max.
CF series（2） CFS series（3） NUCF
Series Metric CF series（1） Miniature CFS Inch series
series CF 3〜CF 5 CFS1.4 〜CFS5 ─ CR 8、CR 8-1、CRH 8-1、CRH 9   3 17
Dimensions and symbols Crowned outer ring Cylindrical outer ring Crowned outer ring Cylindrical outer ring
CF 6 CFS6 ─ CR10、CR10-1、CRH10-1、CRH11   5 20
0 0
Outside dia. of outer ring D See Table 3.1 See Table 3.2 See Table 3.3 CF 8〜CF12-1
-50 -50 ─ ─ CR12〜CR22、CRH12〜CRH22   5 25
CFKR22〜CFKR32
+25 CF16〜CF20-1
Stud dia. d1 h7 h6 ─ ─ CR24〜CR36、CRH24〜CRH36 10 30
0 CFKR35〜CFKR52

0 0 0 CF24〜CF30-2
Width of outer ring C ─ ─ CR48、CRH40〜CRH56 10 40
CFKR62〜CFKR90
-120 -120 -130
─ ─ ─ CRH64 15 50
Note(1)　Also applicable to the Cam Follower G, C-Lube Cam Follower and Cylindrical Roller Cam Follower.
─ ─ NUCF10 R〜NUCF24 R ─ 20 45
─ ─ NUCF24-1R〜NUCF30-2R ─ 25 50
Note (1)　Also applicable to full complement type, crowned outer ring and sealed type.
Table 3.1 Tolerances and allowable values of outer rings (Metric CF series cylindrical outer rings(1)) unit: μ m
(2)　Only representative types are shown in the table, but this table is applicable to the entire Standard Type Cam Follower, Cam Follower
D ∆ Dmp VDsp VDmp Kea G and C-Lube Cam Follower.
Nominal outside dia. of outer ring Single plane mean outside dia. deviation (3)　Only representative types are shown in the table, but this table is applicable to the entire Miniature CFS series.
Outside dia. Mean outside dia. Radial runout of
mm variation in a single variation assembled bearing
Over
  6
Incl.
 18
High
0
Low
-  8
radial plane (Max.)

10
(Max.)

  6
outer ring (Max.)

15
■ Fit
18 30 0 -  9 12   7 15 Tables 5 and 6 show recommended tolerances of Table 5 Recommended fit
mounting holes for Cam Follower studs. Since the Tolerance class of
30 50 0 -11 14   8 20 Type
Cam Follower is supported in a cantilever position, mounting hole for stud
50 80 0 -13 16 10 25
the mounting hole diameter should be prepared with-
80 120 0 -15 19   11 35 Metric CF series H7
out play between the stud and the hole especially
Note(1)　Also applicable to the Cam Follower G. Miniature CFS series H6
when heavy shock loads are applied.
Cylindrical Roller Cam Followers
Inch series
H7
F7
I
Table 3.2 Tolerances and allowable values of outer rings (Miniature CFS series) unit: μ m
Table 6 Dimensional tolerances of mounting hole unit: μ m
∆ Dmp Kea
Single plane mean outside dia. deviation Radial runout of assembled bearing outer ring Nominal outside dia. of stud
F7 H6 H7
(Max.) mm
Class 0 Class 6 Class 5 Class 4 Class 0 Class 6 Class 5 Class 4 Over Incl. Over Incl. Over Incl. Over Incl.
High Low High Low High Low High Low −   3 +16  +  6 +  6 0 +10  0
0 -8 0 -7 0 -5 0 -4 15 8 5 4   3   6 +22 +10 +  8 0 +12 0
  6 10 +28 +13 +  9 0 +15 0
10 18 +34 +16 +11 0 +18 0
Table 3.3 Tolerances and allowable values of outer rings (Inch series cylindrical outer ring) unit: μ m +41 +20 +13 +21
18 30 0 0
D ∆ Dmp VDsp VDmp Kea 30 50 +50 +25 +16 0 +25 0
Nominal outside dia. of outer ring Single plane mean outside dia. Outside dia. Mean outside dia. Radial runout of
mm deviation variation in a single variation assembled bearing
Over Incl. High Low radial plane (Max.) (Max.) outer ring (Max.)

  6  18 10   6 15

18 30 12   7 15
30 50 0 -25 14   8 20
50 80 16 10 25
80 120 19   11 35

1N=0.102kgf=0.2248lbs.
I7 1mm=0.03937inch
I8
■ Maximum Allowable Static Load ■ Track Capacity Table 7.2 Track capacity
Identification Identification Identification Identification
unit: N

The applicable load on Cam Followers is, in some Track capacity is defined as the load which can be con- number Track number Track number Track number Track
cases, limited by the bending strength and shear tinuously applied on a Cam Follower placed on a steel Type of bearing
with crowned capacity with cylindrical capacity with crowned capacity with cylindrical capacity
strength of the stud and the strength of the outer ring cam guide surface without causing deformation or outer ring outer ring outer ring outer ring
instead of the load rating of the needle roller bearing. indentation on the cam guide surface when the outer
CR 8 R 770 CR 8 2 140 − − − −
Therefore, the maximum allowable static load that is ring of the Cam Follower makes contact with the mat-
limited by these strengths is specified. ing cam guide surface (plane). The track capacities CR 8-1R 770 CR 8-1 2 360 CRH 8-1R 401 CRH 8-1 2 360
shown in Tables 7.1 and 7.2 are applicable when the − − − − CRH 9 R 469 CRH 9 2 650
hardness of the mating cam guide surface is 40HRC CR10 R 1 030 CR10 3 210 − − − −
(Tensile strength 1250N/mm2). When the hardness of
the mating cam guide surface differs from 40HRC, the CR10-1R 1 030 CR10-1 3 480 CRH10-1R 579 CRH10-1 3 480
track capacity is obtained by multiplying the value by − − − − CRH11 R 658 CRH11 3 830
the track capacity factor shown in Table 8. CR12 R 1 340 CR12 4 500 CRH12 R 853 CRH12 4 500
If lubrication between the outer ring and the mating
CR14 R 1 630 CR14 5 250 CRH14 R 1 050 CRH14 5 250
cam guide surface is insufficient, seizure and/or wear
may occur depending on the application. Therefore, CR16 R 1 970 CR16 7 280 CRH16 R 1 420 CRH16 7 280
attention must be paid to lubrication and surface CR18 R 2 300 CR18 7 710 CRH18 R 1 660 CRH18 7 710
roughness of the mating cam guide especially for CR20 R 2 680 CR20 10 700 CRH20 R 2 160 CRH20 10 700
high-speed rotations such as cam mechanisms.
Inch CR22 R 3 050 CR22 11 800 CRH22 R 2 450 CRH22 11 800
For lubrication between the outer ring and the mating
cam guide surface, C-Lube Unit for Cam Followers is series（1） CR24 R 3 410 CR24 15 400 CRH24 R 3 410 CRH24 15 400
recommended. (See page Ⅰ20.) CR26 R 3 820 CR26 16 700 CRH26 R 3 820 CRH26 16 700
Table 7.1 Track load capacity unit: N CR28 R 4 210 CR28 21 000 CRH28 R 4 210 CRH28 21 000
Identification Identification CR30 R 4 610 CR30 22 500 CRH30 R 4 610 CRH30 22 500
number Track number Track
Type of bearing CR32 R 5 050 CR32 30 900 CRH32 R 5 690 CRH32 30 900
with crowned capacity with cylindrical capacity
outer ring outer ring CR36 R 5 900 CR36 34 700 CRH36 R 6 640 CRH36 34 700
− − − − CRH40 R 8 970 CRH40 45 000
CF 3 R 542 CF 3 1 360
− − − − CRH44 R 10 200 CRH44 49 500
CF 4 R 712 CF 4 1 790
− − CR48 64 300 CRH48 R 11 400 CRH48 64 300
CF 5 R 794 CF 5 2 210
− − − − CRH52 R 12 700 CRH52 69 600
CF 6 R 1 040 CF 6 3 400
− − − − CRH56 R 14 100 CRH56 87 000
CF 8 R 1 330 CF 8 4 040
− − − − CRH64 R 16 800 CRH64 113 000
CF10 R・CFKR22R
CF10-1R・CFKR26R
1 610
2 030
CF10 ・CFKR22
CF10-1・CFKR26
4 680
5 530
Notes(1)　Only representative types are shown in the table, but this table is applicable to the entire Inch series. I
CF12 R・CFKR30R 2 470 CF12 ・CFKR30 7 010 Table 8 Track capacity factor
Metric CF12-1R・CFKR32R 2 710 CF12-1・CFKR32 7 480 Track capacity factor
Hardness Tensile strength
CF series（1） CF16 R・CFKR35R 3 060 CF16 ・CFKR35 11 200 With crowned With cylindrical
HRC N/mm2
CF18 R・CFKR40R 3 660 CF18 ・CFKR40 14 500 outer ring outer ring

CF20 R・CFKR52R 5 190 CF20 ・CFKR52 23 200 20 760 0.22 0.37

CF20-1R・CFKR47R 4 530 CF20-1・CFKR47 21 000 25 840 0.31 0.46
CF24 R・CFKR62R 6 580 CF24 ・CFKR62 34 300 30 950 0.45 0.58
CF24-1R・CFKR72R 8 020 CF24-1・CFKR72 39 800 35 1 080 0.65 0.75
CF30 R・CFKR80R 9 220 CF30 ・CFKR80 52 700 38 1 180 0.85 0.89
CF30-1R・CFKR85R 9 990 CF30-1・CFKR85 56 000 40 1 250 1.00 1.00
CF30-2R・CFKR90R 10 800 CF30-2・CFKR90 59 300 42 1 340 1.23 1.15
− − CFS1.4 128 44 1 435 1.52 1.32
− − CFS2 220 46 1 530 1.85 1.51
− − CFS2.5 298 48 1 635 2.27 1.73
Miniature
− − CFS3 485 50 1 760 2.80 1.99
CFS series（2）
− − CFS4 799 52 1 880 3.46 2.29
− − CFS5 1 210 54 2 015 4.21 2.61
− − CFS6 1 680 56 2 150 5.13 2.97
Notes(1)　Only representative types are shown in the table, but this table is applicable to the entire Standard Type Cam Follower series. Also 58 2 290 6.26 3.39
applicable to Cam Follower G, C-Lube Cam Follower and Cylindrical Roller Cam Follower.
 　　  (2)　Only representative types are shown in the table, but this table is applicable to the entire Miniature CFS series.
1N=0.102kgf=0.2248lbs.
I9 1mm=0.03937inch
I10
■ Allowable Rotational Speed ■ Lubrication ■ Oil Hole
The allowable rotational speed of Cam Followers is Grease-prepacked Cam Followers are shown in Table The position of oil hole is shown in Table 11.
affected by mounting and operating conditions. For 10. The lubricating grease prepacked in these bear- Perform greasing quietly by fitting a lubrication nozzle
reference, Table 9 shows d1n values when only pure ings is ALVANIA GREASE S2 (SHOWA SHELL indicated in Table 12 to a straight type grease gun in
radial loads are applied. Considering that axial loads SEKIYU K.K.). JIS B 9808 and pressing the nozzle against the
also act under actual operating conditions, the recom- For Cam Followers without prepacked grease, grease grease nipple or re-greasing fitting.
Due to their structures, lubrication is not possible for
mended d1n value is 1/10 of the value shown in the should be packed through the oil hole in the stud for
CF3/CF4, C-Lube Cam Follower, Cam Follower G
table. use. If they are used without grease, wear of rolling
and Miniature CFS series.
In case of C-Lube Cam Follower, d1n value is 10000 contact surfaces may take place, leading to a short
or less. bearing life.
Table 11 Position of oil hole 〇：Oil hole is prepared.
Table 9 d1n values of Cam Followers（1）
Oil hole position ① ② ③
Lubricant Head Stud Stud
Grease Oil Series outside end
Type Size of stud diameter d（
1 ） mm
1 surface
Caged type 84 000 140 000 2
With hexagon 　　 d1≦10 〇( ) − 〇
Full complement type 42 000 70 000 socket on both stud
CFKR
ends (2)
Cylindrical Roller Cam Follower 66 000 110 000 10＜d1 〇 〇 〇
Note(1)　d1n value ＝ d1 × n　
where, 　d1 : Stud diameter   mm 　　　 d1＜5 − − −
　　　　　　　　 n : Rotational speed  min-1 CF
Standard Type
CFES
Cam Followers With hexagon hole 5≦d1≦10 〇(3) − −
CFE
series
Table 10 Bearings with prepacked grease CF…W
〇：Prepacked ×：Not prepacked 10＜d1 〇(2) 〇 〇
Item With cage
Full complement 　　　 d1≦12 〇 − − ②
Series Shield type Sealed type CF-RU1、CF-FU1(4)
Size of stud diameter d1（1）
 mm With hexagon hole With screwdriver slot With hexagon hole With screwdriver slot 　 12＜d1 〇 〇 〇
　　　 d1≦10 〇(3) − − ① ③
CF    3〜  5 − CF-SFU With hexagon hole
CFKR 〇 10＜d1 〇(5) − −
Standard Type CFES 6〜10 − 〇 − Cam Follower G CF … G − − −
Cam Followers
CFE 〇 C-Lube Cam Followers CF … WB … /SG − − −
CF…W 12〜30 × Miniature CFS
series CFS
− − −
CF-RU1、CF-FU1
CF-SFU
−
−
−
−
−
〇
〇
−
−
−
series
Cylindrical Roller
CFS…W

NUCF With hexagon hole

　　　 d1≦10 〇(3) − − I
Cam Followers 10＜d1 〇(2) 〇 〇
Cam Follower G CF …G 〇 − − − −
　　 　d1≦6.35 − − −
C-Lube Cam Followers CF …WB…/SG(2) − − × − − With hexagon hole
6.35 ＜d1 − 〇 〇
Miniature CFS CFS CR
〇 − − − 〇 　　 d1≦6.35 〇 − −
series CFS…W With screwdriver slot
6.35 ＜d1 〇 〇 〇
Cylindrical Roller Cam Followers NUCF − − − − 〇 Inch series
d1≦7.938 − − −
CR 〇 〇 〇 〇 〇 With hexagon hole
Inch series 7.938＜d1 − 〇 〇
CRH − − − − 〇 CRH
d1≦7.938 〇 − −
With screwdriver slot
Notes(1)　For Eccentric Type Cam Followers (CFE), thread diameter G as shown in the dimension table is applicable. 7.938＜d1 〇 〇 〇
 　　  (2)　C-Lube, a thermosetting solid-type lubricant, fills the inner space of the bearing. Notes(1)　In case of Eccentric Type Cam Followers (CFE), thread diameter G shown in the table of dimensions is applicable in place of stud dia.
and the oil hole on the outer surface of the stud cannot be used for lubrication.
 　　 (2)　Grease nipple is incorporated in the hexagon hole. Re-greasing can be made from the stud head and the stud end by press fitting a
supplied grease nipple into the stud end. See page Ⅰ4.
 　　 (3)　Re-lubrication can be made from the re-greasing fitting that is inserted into the hexagon hole. See page Ⅰ4.
 　　 (4)　Tapped holes for oil connectors are provided at the stud end and hole of the head.
 　　 (5)　Re-greasing can be made from the grease nipple in the hexagon hole.

1N=0.102kgf=0.2248lbs.
I11 1mm=0.03937inch
I12
Table 12 Type and Dimension of Lubrication Nozzles
Applicable grease nipple and
■ Accessories
Type Dimension Cam Follower accessories are shown in Table 13.
re-grease fitting
Grease nipple dimensions are shown in Table 14 and
Width across
126 29
flats 12 Table 15. Dimensions of plug for unused oil hole and
Width across flats 12 NPF3（1） dimensions of plug inserter are shown in Table 16.

φ5
A-5126T NPF6-1（1） Nut dimensions are shown in Table 17 and Table 18.
Re-grease fitting（1） Table 13 Accessories 〇：Attached

°
φ1.5
PT1/8

17
Accessories
Series (1) Grease nipple Plug Nut Spring washer
120 29 Size of stud dia. d1 mm
Width across
〇 − 〇 −
Width across
R flats 12
flats 12 With hexagon socket on both stud ends CFKR
2.
5

φ5
A-5120R d1 ≦ 10 − − 〇 −
Standard Type Cam Follower CF
10 ＜ d1 〇 − 〇 −
PT1/8
NPF4-1（1） Eccentric Type Cam Follower d1 ≦ 10 − − 〇 〇
120 29 NPF6-1（1） 　 CFE 10 ＜ d1 〇 − 〇 〇
Width across Width across
Solid Eccentric Stud Type d1 ≦ 10 − − 〇 −
flats 12
flats 12
Cam Follower CFES
B-5120R Thrust Disk Type
φ

10 ＜ d1 〇 − 〇 −
5

R2
.5 Cam Follower CF … W
φ5

PT1/8 Centralized Lubrication Type Cam Follower CF − RU1、CF − FU1 − − 〇 −

120 29 Easy Mounting Type Cam Follower CF − SFU − − − −
CF … G − − 〇 −
Width across Width across
flats 12 flats 12 Cam Follower G
C-Lube Cam Follower CF … WB … /SG − − 〇 −
A-5120V
Miniature Type Cam Follower CFS
Thrust Disk Type − − 〇 −
CFS … W
φ5

PT1/8 Miniature Cam Follower

240 29 Cylindrical Roller Cam Follower NUCF d1 ≦ 10 − − 〇 −
〇 − 〇 −
Width across
Width across
flats 12 flats 12 (With Hexagon socket) 10 ＜ d1
Inch series Cam Follower CR d1 ≦ 6.35 − − 〇 −
φ5

A-5240V NPT4-1
(With Hexagon socket) 9.525 ≦ d1 〇 〇 〇 −
NPT6-1
〇 〇 〇 −
I
PT1/8 Inch series Cam Follower CR (With Screw driverslot)
NPB2
Inch series Cam Follower CRH d1 ≦ 7.938 − − 〇 −
120 29 NPB3
Width across
Width across
flats 12
(With Hexagon socket) 11.112≦ d1 〇 〇 〇 −
flats 12 NPB3-1
Inch series Cam Follower CRH (With Screw driverslot) 〇 〇 〇 −
B-5120V NPB4
φ

Note(1)　For Eccentric Type Cam Follower CFE, thead diameter G is applied.

5

Remark: The standard grease nipple (brass) is included in the Stainless Steel Made Cam Follower.
We also have the stainless steel grease nipple. Please contact and request the product.
φ5

PT1/8

240 29 Table 14 Dimensions of grease nipple for Standard Type Cam Followers (1)
Width across
Width across
flats 12
flats 12 L
W
B-5240V
φ
5

Inserter
φ5

d0

D
d
PT1/8
Grease nipple
Note(1)　HSP-3(Yamada Corporation)can be used for them.
Remark The above nozzles can be atached on the standard grease gun shown below. Dimensions of grease nipple mm Stud diameter d1 (2) Dimension of inserter mm Stud
If required, please consult to with type of lubrication nozzle. Identification number +0.05
d D L W mm d0 −0.05
Body of grease gun NPF3(3) 3 4 4.5 1.3 10 4.1
Lubrication Nozzle NPF4-1 4 5 5 1.5 12〜16 5.3
NPF6-1 6 7 8 2 18〜30 7.3
Notes (1)　Applicable to Cam Followers other than Inch series Cam Followers.
 　　  (2)　For Eccentric Type Cam Followers, thread diameter G as shown in the dimension table is applicable.
 　　  (3)　Only Double Hex Hole Cam Followers (CFKR) sizes 22 and 26 are applicable.
Remark The same grease nipple as the accessory is integrated in the hexagon hole on the head.

1N=0.102kgf=0.2248lbs.
I13 1mm=0.03937inch
I14
Table 15 Dimensions of grease nipple for Inch series Cam Followers Table 18 Inch series nut dimensions
Identification Dimensions mm Stud diameter d1 Nut dimensions mm
Applicable Cam Followers Model of bearing
number d D D1 L L1 W (inch) G　UNF m s e
 4.826 No.10-32  4  8  9.2
NPB2 3.18 7.5 6 9 5.5 1.5 CR8 〜 CR10-1、CRH8-1 〜 CRH11
  6.35 (  1/ 4)   1/  4-28   5.5 10 11.5
NPB3 4.76 7.5 6 10 5.5 1.5 CR12 〜 CR22、CRH12 〜 CRH22
5
 7.938 (  /16)   5/16-24   6.5 12 13.8
NPB3-1 4.76 7.5 6 12.5 5.5 1.55 CR24 〜 CR36、CRH24 〜 CRH44
 9.525 (  3/ 8)   3/  8-24  8 14 16.2
NPB4 6.35 8 6 13 6 2 CR48、CRH48 〜 CRH64
11.112 (  7/16)   7/16-20 10 17 19.5 G
12.7 (  1/ 2)   1/  2-20 11 19 21.9

(e)
15.875 (  5/ 8)   5/  8-18 14 23 26.5
Table 16 Dimensions of plug for Inch series Cam Followers CR
19.05 (  3/ 4)   3/  4-16 16 26 30
CRH m s
Identification Dimensions of plug mm Dimension of inserter mm Inserter 22.225 (  7/ 8)   7/  8-14 19 32 37
Applicable bearings (1)
number 25.4 (1   ) 1     -14UNS 22 36 41.4
D t B d   0
－0.1
28.575 (1 1/ 8) 1 1/  8-12 24 41 47.1
USB2F 3.18 0.3 3.3 2.3 CR 8 〜CR10-1
31.75 (1 1/ 4) 1 1/  4-12 27 46 53.5
USB3F 4.76 0.4 4.3 3.7 CR12〜CR36、CRH12 〜CRH44 38.1 (1 1/ 2) 1 1/  2-12 33 55 63.5
Stud
USB4F 6.35 0.5 4.8 5.2 CR48、CRH48〜CRH64 44.45 (1 3/ 4) 1 3/  4-12UN 38 65 75.1

Note(1)　Shows representative types. 50.8 (2   ) 2     -12UN 44 75 86.6

Table 17 Metric series nut dimensions

Stud diameter Nut dimensions mm
■ Special Specification Table 20 D
 imension of assembled NPT type
grease nipple
Model of bearing
d1(1) G m s e The grease nipple supplied with Metric series Cam
 1.4 M 1.4×0.3 1.1  3   3.25 Follower with hexagon socket as an accessory may
 2 M 2  ×0.4  1.6  4  4.6 be replaced with the NPT type grease nipple indicated
 2.5 M 2.5×0.45 2  5  5.8 in Table 19 upon your request. If required, please
CF  3 M 3  ×0.5  2.4 5.5  6.4 order with supplemental code, "/NP" at the end of
CFKR  4 M 4  ×0.7 3.2  7  8.1 identification number.
CFES G
 5 M 5  ×0.8 4  8  9.2
CFE
CF…W  6 M 6  ×1 5 10 11.5 (e)
Example of Identification Number
CF-RU1  8 M 8  ×1.25 6.5 13 15
CF-FU1 M10   ×1.0(2)
m s CF  12 BUU ／ NP
CF…G
CF…WB…/SG
10

12
M10   ×1.25
M12   ×1.5
8

10
17

19
19.6

21.9 Code number

Dimension mm Size of stud dia. d1(1) I
CFS B4 B5 mm
16 M16   ×1.5 13 24 27.7 Table 19 Dimension of NPT type grease nipple
CFS…W
NUCF
NPT4-1 6 2 12 〜 16
18 M18   ×1.5 15 27 31.2
20 M20   ×1.5 16 30 34.6 NPT6-1 8 4 18 〜 30
24 M24   ×1.5 19 36 41.6 Note(1)　For Eccentric Type Cam Follower CFE, thread diameter G
is applied.
30 M30   ×1.5 24 46 53.1
Note(1)　For Eccentric Type Cam Followers (CFE), thread diameter G as shown in the dimension table is applicable.
Note(2)　Applicable to Double Hex Hole Cam Followers (CFKR).

Dimension of grease nipple mm Size of stud dia. d (1)

1
Code number
d D D1 L L1 W mm
NPT4-1 4 8 6 12 6 2 12 〜 16
NPT6-1 6 8 6 14 8 4 18 〜 30
Note(1)　For Eccentric Type Cam Follower CFE, thread diameter G
is applied.
Remark　Not applicable to Double Hex Hole Cam Followers.

1N=0.102kgf=0.2248lbs.
I15 1mm=0.03937inch
I16
■ Operating Temperature Range ■ Mounting 3 When mounting Cam Followers, fix in place by
holding the hexagon hole or screwdriver slot with a
6 Solid Eccentric Stud Type Cam Followers and
Eccentric Type Cam Followers, are mounted in
Operating temperature range of Cam Followers is 20°C 1 Make the center axi s of the mounti ng hol e hex wrench or slotted screwdriver and use a reference position where mark on the head of
~ +120°C. However, note that the maximum allowable perpendicular to the moving direction of the Cam wrench to tighten on a nut. (See Fig. 3) stud is located as Fig.5. The outer ring position can
temperature varies in models shown in Table 21. Follower and match the side shoulder accurately If mounting by turning the hexagon hole or be adjusted appropriately by turning the stud with a
screwdriver or hexagon bar wrench using the
with the seating surface indicated by dimension  f  screwdriver slot itself, the hexagon hole or
Table 21 Limitation of operating temperature range screwdriver slot or hexagon hole of the stud head.
in the table of dimensions. (See Fig. 1) screwdriver slot of the Cam Follower may become
The stud is fixed with a nut and a spring washer,
Item With cage The chamfered mounting hole should be as small damaged.
etc. The tightening torque should not exceed the
Model as possible (C0.5 or so).
Stud diameter d1 mm Shield type Sealed type values of maximum tightening torque shown in the
When mounting Cam Followers, do not hit the table of dimensions.
Miniature Type flange head of the Cam Follower directly with a
Cam Followers CFS − 20°C 〜 When shock loads are applied and the adjusted
d1 ＝ 2 − hammer, etc. This may lead to a bearing failure eccentricity has to be ensured, it is recommended
Thrust Disk Type 110°C(1)
Miniature Cam Followers CFS … W such as irregular rotation or cracking. to make holes in the housing, stud and eccentric
− 20°C 〜 − 20°C 〜 If the Cam Follower outer ring is not in good contact collar, and fix the stud with a dowel pin as shown in
Standard Type d1 ＝ 3、4 with the mating running surface then we Fig. 6. However, when the stud diameter is less
Cam Followers CF … B 110°C(1) 　 80°C
recommend use of a crowned outer ring type. than 8 mm (Eccentric collar diameter 11 mm), it is
Thrust Disk Type − 20°C 〜 − 20°C 〜
Cam Followers CF … WB d1 ＝ 5 difficult to make a hole in the stud because the stud
120°C 　 80°C is through-hardened.
Standard Type Cam Followers / Eccentricity
Fig. 3 Methods of mounting
Stainless Steel Made CF … FB − 20°C 〜 − 20°C 〜
3 ≦ d1 ≦ 5 Stud dia.
Thrust Disk Type Cam Followers / 110°C(1) 　 80°C
Stainless Steel Made CF … FWB 4 When tightening the nut, the tightening torque
should not exceed the values shown in the table of
C-Lube Cam Followers − 15°C 〜 dimensions. If the tightening torque is too large, it
CF … WB … /SG 5 ≦ d1 ≦ 20 −
　 80°C(2) is possible that the threaded portion of the stud will
Notes(1)　100°C when used continuously. be broken. When there is a possibility of loosening,
 　　 (2)　Below 60°C is recommended for long use.
a special nut such as a lock nut, spring washer, or
Load
self-locking nut should be used.
Fig. 1 Seating surface Fig. 5 R
 eference position for adjusting of Solid
5 When direct-fixing the Cam Follower without nuts Eccentric Stud Type Cam Followers and
for mounting as shown in Fig. 4, it may be difficult Eccentric Type Cam Follwers
2 The mark on the flange head of the stud
to achieve sufficient tightening torque. If the screw
indicates the position of the oil hole on the Dowel pin
then loosens, stress may concentrate on the
raceway. Avoid locating the oil hole within the
loading zone. This may lead to a short bearing life.
thread, causing the stud to break. Such a method is
not recommended.
I
(See Fig. 2.) The hole located in the middle part of
the stud perpendicular to the stud center axis is
used for greasing or locking.

Oil Hole
Fig. 6 M
 ounting example of Solid Eccentric
Stud Type Cam Follower

Fig. 4 Methods of mounting

Load

Fig. 2 Oil hole position and loading direction

1N=0.102kgf=0.2248lbs.
I17 1mm=0.03937inch
I18
7 In case of Eccentric Type Cam Followers (CFE), 9 For mounting Easy Mounting Type Cam Followers,
the length of the mounting hole should be more it is recommended to fix the fixing screw from the Option Parts
than 0.5 mm longer than the dimension B3
(Eccentric collar width) shown in the table of
dimensions. (See Fig. 7.)
upper side to the stepped portion of the stud. (See
Fig. 8.)
While M5 - M6 screws are generally used as fixing
C-Lube Unit for Cam Followers
screws, adjust the size used depending on the
usage criteria. ■ Structure and features
C-Lube unit for Cam Follower is a lubrication Regular lubrication is not needed as lubrication oil is
part to be mounted on the Cam Follower and its inte- supplied onto the outside diameter surface of the
gral capillary lubricating element has a lot of lubrica- outer ring and mating guide surface (cam guide sur-
tion oil impregnated in it. face). The grease is not scattered and contamination
The capillary lubricating element is consecutive of the surrounding environment is prevented.
porous resin formed by sinter molding of fine resin The combination with C-Lube cam follower (See
Fig. 7 L
 ength of the mounting hole of powder and a lot of lubrication oil is impregnated in it Page I49) realizes maintenance-free cam follower
Eccentric Type Cam Follower by using the capillary action that occurs within the inside and cam guide surface.
Fig. 8 M
 ounting example of Easy Mounting
Type Cam Follower internal space.
8 Eccentric callor is available for Inch series Cam
Followers.
Cam Followers with Eccentric collars, CRE are also ■ Precaution For Use Structure of C-Lube Unit for Cam Followers
available. If required, please consult with . C-Lube unit C-Lube Magnified photos of C-Lube
1 Do not wash C-Lube Cam Follower with organic
Table 20 E
 ccentric collars for Inch series Cam solvent and/or white kerosene, which have the
Before impregnating oil After impregnating oil
Followers ability of removing fat nor leave them in contact
with the above agents.

2 To ensure normal rotation of the C-Lube Cam

Follower, apply a load of 1% or over of the dynamic Fusion- bonded Resin part Lubricant part
load rating at use.
Resin particles are strongly fusion bonded. Lubricant is retained in cavities amongst
resin particles.
C-Lube Cam Follower
unit: mm
Identifical Outer diameter Length Eccentri

■ Identification number ■ Allowable Rotational speed

Applicable
number of collar of collar city Stud dia.

I
of collar de B3 ε d Cam Followers

1⁄4 CR 8 The identification number example of C-Lube The Rotational speed of Cam Follower with
EB 8 6.350 ( ) 6.350 ( 1⁄4 ) 0.250 4.826 CR 8-1 (V)(B)(UU)(R) Unit is shown below. C-Lube Unit should not exceeded d1n=10,000 for ref-
EB10 9.525 ( 3⁄8 ) 9.525 ( 3⁄8 ) 0.380 6.350 ( 1⁄4 ) CR10 (V)(B)(UU)(R) erence.
CR10-1
EB12 12.700 ( 1⁄2 ) 12.700 ( 1⁄2 ) 0.380 9.525 ( 3⁄8 ) CR12 (V)(B)(UU)(R) d1n= d1 × n
CR14
7⁄16) CR16 (V)(B)(UU)(R)
d1 : Stud diameter of Cam Follower, mm
EB16 15.875 ( 5⁄8 ) 15.875 ( 5⁄8 ) 0.760 11.112 ( CR18
Model code n : Rotational speed, min-1
CR20
EB20 17.450 17.450 0.760 12.700 ( 1⁄2 ) CR22 (V)(B)(UU)(R)
CR24
EB24 22.225 ( 7⁄8 ) 22.225 ( 7⁄8 ) 0.760 15.875 ( 5⁄8 ) CR26 (V)(B)(UU)(R) Size of CL
(Size of combined Cam Follower)
■ Minimum rotational angle
CR28
EB28 25.400 (1 ) 25.400 (1 ) 0.760 19.050 ( 3⁄4
) CR30 (V)(B)(UU)(R) unit :mm Lubricating oil is supplied to the whole external diameter
CR32 surface of the outer ring. Accordingly, use the product
EB32 30.150 30.150 0.760 22.225 ( 7⁄8 ) CR36 (V)(B)(UU)(R) in a condition in which the outer ring makes one or more
EB48 44.450 (1 3⁄4 ) 44.450 (1 3⁄4 ) 1.520 31.750 (1 1⁄4 ) CR48 VUU turns.

■ Operating temperature
Allowable operating temperature range of Cam
Follower with C-Lube Unit is -15 to 80˚C.

1N=0.102kgf=0.2248lbs.
I19 1mm=0.03937inch
I20
■ Mounting ■ Precaution for use Table 21 Dimensions of C-Lube Unit for Cam Followers

1 Set the C-Lube Unit perpendicularly to the center 1 Do not wash with organic solvent and/or white
axis of Cam Follower and fix together with Cam kerosene, which have the ability of removing fat nor
Follower by tightening nut. (See Fig. 9.)
leave them in contact with the above agents.

2 Do not apply a load onto the C-Lube Unit directly.

3 To ensure normal rotation of the Cam Follower,

apply a load of 1% or over of the dynamic load
rating at use.
Also, the outer ring needs to be rotate over a
revolution to supply lubricant on entire outer
diameter surface.
Fig. 9 Mounting of C-Lube Unit
4 The maximum allowable load on Boundary Dimensions mm Applicable Cam Followers
Cam
Follower with C-Lube Unit is, 80% of the maximum Model number Boundary Dimensions mm
2 Position of C-Lube Unit is adjustable. C-Lube Unit W H T t1 Model number（1）
must be positioned avoiding loading direction. (See allowable load of the needle bearing. D B
Fig. 10.) C-Lube Unit may be damaged and influenced to
the smooth roatation and lubricating performance CL 5 12.4 10.7 12.1 1.5 CF 5 B 13 10
by excessive load. CF 6 B
CL 6 15.4 12.6 14 1.5 16 12.2 max

5 After assembling C-Lube Unit and Cam Followers CL 8 18.4 14.2 14 1.5 CF 8 B 19 12.2 max
in the machine, please confirm that C-Lube unit CF 10 B
CL 10 21 17 15.5 2 CFKR 22 22 13.2 max
provides oil correctly to the cam guide surface CF 10-1 B
before actual operation. CL 10-1 21 19.2 15.5 2 CFKR 26 26 13.2 max
CF 12 B
CL 12 29 21 17.5 2 CFKR 30 30 15.2 max
Load 6 Do not use in the environment which contamination CF 12-1 B
CL 12-1 29 22 17.5 2 CFKR 32 32 15.2 max
Fig. 10 Load direction of Cam Follwer of liquid and/or harmful foreign matter are
CL 16 33.8 27.4 23.4 2.5 CF 16 B 35 19.6 max
expected. CFKR 35
CL 18 38.8 30.4 25.4 2.5 CF 18 B 40 21.6 max
3 When tightening the nut, the tightening torque 7 Replace with new C-Lube Unit when inside oil CFKR 40
should not be exceeded the value maximum CF 20 B
I
finishes completely. Re-lubrication is not possible. CL 20 45.8 38.4 29.9 3 CFKR 52 52 25.6 max
tightening torque on dimension table.
I n case loosening of the nut is predicted due to CL 20-1 45.8 35.4 29.9 3 CF 20-1 B 47 25.6 max
vibration, using lock nut, spring washer and other CFKR 47
special washer are recommended. Note(1)　Only representative types are shown in the table, but this table is applicable to the same size of Standard Type Cam Followers, Double
Hex Hole Cam Followers, Cam Follower G, Thrust Disk Type Cam Followers, Centralized Lubrication Type Cam Followers, C-Lube
Cam Followers and Cylindrical Roller Cam Followers.
Remark Load on the Cam Follower with the C-Lube unit equipped must be up to 80% of the maximum allowable static load of the Cam Follower
to be combined. For the maximum allowed static load of each Cam Follower, please see the dimension tables of respective models.

1N=0.102kgf=0.2248lbs.
I21 1mm=0.03937inch
I22
 CAM FOLLOWERS
Standard Type Cam Followers With Cage/With Hexagon Hole
C C

B3
g2

g1
D

G
H H

d1
d1
G1
G1
C1
C1

R=500 R= 500 B B2
B B2
B1
B1

Stud dia. 3−30mm CF … BR CF … BR

CF … B CF … BUUR CF … BUU
Stud dia d1　3-10mm Stud dia d1　12-30mm

Identification number Mass Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
Stud (Ref.) dimension tightening load rating load rating allowable
f torque static load
dia.
Shield type Sealed type (1)
C C0
With crowned With cylindrical With crowned With cylindrical D C d1 G G1 B B1 B2 B3 C1 g1 g2 H rs min Min. 　
mm outer ring outer ring outer ring outer ring g N-m N N N
mm

3 CF 3 BR CF 3 B CF 3 BUUR CF 3 BUU 4.3 10 7 3 M 3×0.5 5 8 17 9 ─ 0.5 ─ ─ 2 0.2 6.8 0.34 1 500 1 020 384
4 CF 4 BR CF 4 B CF 4 BUUR CF 4 BUU 7.4 12 8 4 M 4×0.7 6 9 20 11 ─ 0.5 ─ ─ 2.5 0.3 8.3 0.78 2 070 1 590 　834
5 CF 5 BR CF 5 B CF 5 BUUR CF 5 BUU 10.3 13 9 5 M 5×0.8 7.5 10 23 13 ─ 0.5 ─ ─ 3 0.3 9.3 1.6 2 520 2 140 1 260
6 CF 6 BR CF 6 B CF 6 BUUR CF 6 BUU 18.5 16 11 6 M 6×1 8 12.2max 28.2max 16 ─ 0.6 ─ ─ 3 0.3 11 2.7 3 660 3 650 1 950
CF 8 BR CF 8 B CF 8 BUUR CF 8 BUU 28.5 19 11 8 M 8×1.25 10 12.2max 32.2max 20 ─ 0.6 ─ ─ 4 0.3 13 6.5 4 250 4 740 4 620
8
CF 8 BRM CF 8 BM CF 8 BUURM CF 8 BUUM 28.5 19 11 8 M 8×1 10 12.2max 32.2max 20 ─ 0.6 ─ ─ 4 0.3 13 7.1 4 250 4 740 4 620

CF 10 BR CF 10 B CF 10 BUUR CF 10 BUU 45 22 12 10 M10×1.25 12 13.2max 36.2max 23 ─ 0.6 ─ ─ 4 0.3 16 13.8 5 430 6 890 6 890
CF 10 BRM CF 10 BM CF 10 BUURM CF 10 BUUM 45 22 12 10 M10×1 12 13.2max 36.2max 23 ─ 0.6 ─ ─ 4 0.3 16 14.7 5 430 6 890 6 890
10
CF 10-1 BR
CF 10-1 BRM
CF 10-1 B
CF 10-1 BM
CF 10-1 BUUR
CF 10-1 BUURM
CF 10-1 BUU
CF 10-1 BUUM
60
60
26
26
12
12
10
10
M10×1.25
M10×1
12
12
13.2max
13.2max
36.2max 23
36.2max 23
─
─
0.6
0.6
─
─
─
─
4
4

0.3
0.3
16
16
13.8
14.7
5 430
5 430
6 890
6 890
6 890
6 890 I
CF 12 BR CF 12 B CF 12 BUUR CF 12 BUU 95 30 14 12 M12×1.5 13 15.2max 40.2max 25 6 0.6 4 3 6 0.6 21 21.9 7 910 9 790 9 790
12
CF 12-1 BR CF 12-1 B CF 12-1 BUUR CF 12-1 BUU 105 32 14 12 M12×1.5 13 15.2max 40.2max 25 6 0.6 4 3 6 0.6 21 21.9 7 910 9 790 9 790
16 CF 16 BR CF 16 B CF 16 BUUR CF 16 BUU 170 35 18 16 M16×1.5 17 19.6max 52.1max 32.5 8 0.8 4 3 6 0.6 26 58.5 12 000 18 300 18 300
18 CF 18 BR CF 18 B CF 18 BUUR CF 18 BUU 250 40 20 18 M18×1.5 19 21.6max 58.1max 36.5 8 0.8 6 3 8 1 29 86.2 14 800 25 200 25 200
CF 20 BR CF 20 B CF 20 BUUR CF 20 BUU 460 52 24 20 M20×1.5 21 25.6max 66.1max 40.5 9 0.8 6 4 8 1 34 119 20 700 34 600 34 600
20
CF 20-1 BR CF 20-1 B CF 20-1 BUUR CF 20-1 BUU 385 47 24 20 M20×1.5 21 25.6max 66.1max 40.5 9 0.8 6 4 8 1 34 119 20 700 34 600 34 600
CF 24 BR CF 24 B CF 24 BUUR CF 24 BUU 815 62 29 24 M24×1.5 25 30.6max 80.1max 49.5 11 0.8 6 4 12 1 40 215 30 500 52 600 52 000
24
CF 24-1 BR CF 24-1 B CF 24-1 BUUR CF 24-1 BUU 1 140 72 29 24 M24×1.5 25 30.6max 80.1max 49.5 11 0.8 6 4 12 1 40 215 30 500 52 600 52 000
CF 30 BR CF 30 B CF 30 BUUR CF 30 BUU 1 870 80 35 30 M30×1.5 32 37 max 100 max 63 15 1 6 4 17 1 49 438 45 400 85 100 85 100
30 CF 30-1 BR CF 30-1 B CF 30-1 BUUR CF 30-1 BUU 2 030 85 35 30 M30×1.5 32 37 max 100 max 63 15 1 6 4 17 1 49 438 45 400 85 100 85 100
CF 30-2 BR CF 30-2 B CF 30-2 BUUR CF 30-2 BUU 2 220 90 35 30 M30×1.5 32 37 max 100 max 63 15 1 6 4 17 1 49 438 45 400 85 100 85 100

Note(1)　　 Minimum allowable value of chamfer dimension r

Remarks1.　Models with a stud diameter d1 of 4 mm or less have no oil hole. For models with a stud dia. 5 to 10mm, oil hole (re-greasing
fitting) is provided at the head. Other models are provided with an oil hole (grease nipple) at the head and an oil hole each on the
outside surface and end surface of the stud.
2.　Shield type models with a stud diameter d1 of 10mm or less and the sealed type models are provided with prepacked grease.
Other models are not provided with prepacked grease. Perform proper lubrication for use.

1N=0.102kgf=0.2248lbs.
I23 1mm=0.03937inch
I24
 CAM FOLLOWERS
Standard Type Cam Followers Full Complement Type/With Hexagon Hole

C C

B3
g2

g1
D

G
H H

d1

d1
G1 G1
C1 C1

R=500 B2 R= 500 B B2
B
B1 B1

Stud dia. 6−30mm CF … VBR CF … VBR

CF … VB CF … VBUUR CF … VBUU
Stud dia. d1　6-10mm Stud dia. d1　12-30mm

Identification number Mass Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
Stud (Ref.) dimension tightening load rating load rating allowable
f torque static load
dia.
Shield type Sealed type (1)
C C0
With crowned With cylindrical With crowned With cylindrical D C d1 G G1 B B1 B2 B3 C1 g1 g2 H rs min Min. 　
mm outer ring outer ring outer ring outer ring g max max N
mm N-m N N

6 CF 6 VBR CF 6 VB CF 6 VBUUR CF 6 VBUU 19 16 11 6 M 6×1 8 12.2 28.2 16 ─ 0.6 ─ ─ 3 0.3 11 2.7 6 980 8 500 1 950
CF 8 VBR CF 8 VB CF 8 VBUUR CF 8 VBUU 29 19 11 8 M 8×1.25 10 12.2 32.2 20 ─ 0.6 ─ ─ 4 0.3 13 6.5 8 170 11 200 4 620
8
CF 8 VBRM CF 8 VBM CF 8 VBUURM CF 8 VBUUM 29 19 11 8 M 8×1 10 12.2 32.2 20 ─ 0.6 ─ ─ 4 0.3 13 7.1 8 170 11 200 4 620

CF 10 VBR CF 10 VB CF 10 VBUUR CF 10 VBUU 46 22 12 10 M10×1.25 12 13.2 36.2 23 ─ 0.6 ─ ─ 4 0.3 16 13.8 9 570 14 500 8 650
CF 10 VBRM CF 10 VBM CF 10 VBUURM CF 10 VBUUM 46 22 12 10 M10×1 12 13.2 36.2 23 ─ 0.6 ─ ─ 4 0.3 16 14.7 9 570 14 500 8 650
10
CF 10-1 VBR CF 10-1 VB CF 10-1 VBUUR CF 10-1 VBUU 61 26 12 10 M10×1.25 12 13.2 36.2 23 ─ 0.6 ─ ─ 4 0.3 16 13.8 9 570 14 500 8 650
CF 10-1 VBRM CF 10-1 VBM CF 10-1 VBUURM CF 10-1 VBUUM 61 26 12 10 M10×1 12 13.2 36.2 23 ─ 0.6 ─ ─ 4 0.3 16 14.7 9 570 14 500 8 650

12 CF 12 VBR CF 12 VB CF 12 VBUUR CF 12 VBUU 97 30 14 12 M12×1.5 13 15.2 40.2 25 6 0.6 4 3 6 0.6 21 21.9 13 500 19 700 13 200
CF 12-1 VBR CF 12-1 VB CF 12-1 VBUUR CF 12-1 VBUU 107 32 14 12 M12×1.5 13 15.2 40.2 25 6 0.6 4 3 6 0.6 21 21.9 13 500 19 700 13 200
16 CF 16 VBR CF 16 VB CF 16 VBUUR CF 16 VBUU 173 35 18 16 M16×1.5 17 19.6 52.1 32.5 8 0.8 4 3 6 0.6 26 58.5 20 700 37 600 23 200 I
18 CF 18 VBR CF 18 VB CF 18 VBUUR CF 18 VBUU 255 40 20 18 M18×1.5 19 21.6 58.1 36.5 8 0.8 6 3 8 1 29 86.2 25 300 51 300 31 100

20 CF 20 VBR CF 20 VB CF 20 VBUUR CF 20 VBUU 465 52 24 20 M20×1.5 21 25.6 66.1 40.5 9 0.8 6 4 8 1 34 119 33 200 64 500 37 500
CF 20-1 VBR CF 20-1 VB CF 20-1 VBUUR CF 20-1 VBUU 390 47 24 20 M20×1.5 21 25.6 66.1 40.5 9 0.8 6 4 8 1 34 119 33 200 64 500 37 500

24 CF 24 VBR CF 24 VB CF 24 VBUUR CF 24 VBUU 820 62 29 24 M24×1.5 25 30.6 80.1 49.5 11 0.8 6 4 12 1 40 215 46 600 92 000 52 000
CF 24-1 VBR CF 24-1 VB CF 24-1 VBUUR CF 24-1 VBUU 1 140 72 29 24 M24×1.5 25 30.6 80.1 49.5 11 0.8 6 4 12 1 40 215 46 600 92 000 52 000
CF 30 VBR CF 30 VB CF 30 VBUUR CF 30 VBUU 1 870 80 35 30 M30×1.5 32 37 100 63 15 1 6 4 17 1 49 438 67 700 144 000 85 900
30 CF 30-1 VBR CF 30-1 VB CF 30-1 VBUUR CF 30-1 VBUU 2 030 85 35 30 M30×1.5 32 37 100 63 15 1 6 4 17 1 49 438 67 700 144 000 85 900
CF 30-2 VBR CF 30-2 VB CF 30-2 VBUUR CF 30-2 VBUU 2 220 90 35 30 M30×1.5 32 37 100 63 15 1 6 4 17 1 49 438 67 700 144 000 85 900

Note(1)　　 Minimum allowable value of chamfer dimension r

Remarks1.   Models with a stud diameter d1 of 10 mm or less have an oil hole (re-greasing fitting) at the head. Other models are provided with
an oil hole (grease nipple) at the head and an oil hole each on the outside surface and end surface of the stud.
2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I25 1mm=0.03937inch
I26
 CAM FOLLOWERS
Standard Type Cam Followers / Stainless Steel Made With Cage/With Hexagon Hole
C C
B3
g2

f
g1
D

G
G
H
H

d1
d1
G1 G1
C1 C1

R=500 B B2
R=500 B B2
B1 B1

Stud dia. 3−20mm CF … FBR CF … FBR CF … FB CF … FBUUR CF … FBUU

Stud dia. d1　3-10mm Stud dia. d1　12-20mm

Identification number Mass Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
Stud (Ref.) dimension tightening load rating load rating allowable
torque static load
dia.
Shield type Sealed type f C C0
(1)
With crowned With cylindrical With crowned With cylindrical D C d1 G G1 B B1 B2 B3 C1 g1 g2 H rs min Min. 　
mm outer ring outer ring outer ring outer ring g N
mm N-m N N

3 CF 3 FBR CF  3 FB CF 3 FBUUR CF  3 FBUU     4.3 10 7 3 M 3×0.5   5   8 17    9 ─ 0.5 ─ ─ 2 0.2  6.8     0.34 1 200 813 384
4 CF 4 FBR CF  4 FB CF 4 FBUUR CF  4 FBUU     7.4 12 8 4 M 4×0.7   6   9 20 11 ─ 0.5 ─ ─ 2.5 0.3  8.3     0.78 1 650 1 270 834
5 CF 5 FBR CF  5 FB CF 5 FBUUR CF 5 FBUU   10.3 13 9 5 M 5×0.8   7.5 10 23 13 ─ 0.5 ─ ─ 3 0.3  9.3     1.6 1 930 1 730 1 260
  12.2 28.2
6 CF 6 FBR CF  6 FB CF 6 FBUUR CF 6 FBUU   18.5 16 11 6 M 6×1  8
max max
16 ─ 0.6 ─ ─ 3 0.3 11     2.7 2 930 2 920 1 950

12.2 32.2
8 CF  8 FBR CF  8 FB CF 8 FBUUR CF 8 FBUU   28.5 19 11 8 M 8×1.25 10
max max
20 ─ 0.6 ─ ─ 4 0.3 13     6.5 3 400 3 790 3 790

CF 10 FBR CF 10 FB CF 10 FBUUR CF 10 FBUU   45 22 13.2 36.2

10 12 10 M10×1.25 12 23 ─ 0.6 ─ ─ 5 0.3 16   13.8 4 340 5 510 5 510
CF 10-1 FBR CF 10-1 FB CF 10-1 FBUUR CF 10-1 FBUU   60
I
26 max max
CF 12 FBR CF 12 FB CF 12 FBUUR CF 12 FBUU   95 30 15.2 40.2
12 32
14 12 M12×1.5 13 25 6 0.6 4 3 6 0.6 21   21.9 6 330 7 830 7 830
CF 12-1 FBR CF 12-1 FB CF 12-1 FBUUR CF 12-1 FBUU 105 max max

19.6 52.1
16 CF 16 FBR CF 16 FB CF 16 FBUUR CF 16 FBUU 170 35 18 16 M16×1.5 17
max max
32.5 8 0.8 4 3 6 0.6 26   58.5 9 620 14 700 14 700

21.6 58.1
18 CF 18 FBR CF 18 FB CF 18 FBUUR CF 18 FBUU 250 40 20 18 M18×1.5 19
max max
36.5 8 0.8 6 3 8 1 29   86.2 11 800 20 200 20 200

20 CF 20 FBR CF 20 FB CF 20 FBUUR CF 20 FBUU 460 52

24 20 M20×1.5 21
25.6 66.1
40.5 9 0.8 8 4 8 1 34 119 16 500 27 700 27 700
CF 20-1 FBR CF 20-1 FB CF 20-1 FBUUR CF 20-1 FBUU 385 47 max max

Note(1)　　 Minimum allowable value of chamfer dimension r

Remarks1.   Models with a stud diameter d1 of 4 mm or less have no oil hole. For models with a stud dia. 5 to 10 mm, oil hole (re-greasing
fitting) is provided at the head. Other models are provided with an oil hole (grease nipple) at the head and an oil hole each on the
outside surface and end surface of the stud.
2.   Shield type models with a stud diameter d1 of 10 mm or less and the sealed type models are provided with prepacked grease.
Other models are not provided with prepacked grease. Perform proper lubrication for use.

1N=0.102kgf=0.2248lbs.
I27 1mm=0.03937inch
I28
 CAM FOLLOWERS CAM FOLLOWERS
Double Hex Hole Cam Followers With Cage

C
C r r
Grease nipple B3
g2

r
Grease nipple

f
g1
g1

G
D

G
H H H H

d1
d1
G1 G1
C1 C1

B2 B B2 R=500
B
B1 B1

Stud dia. 10−30mm Outside dia. of outer ring D 22, 26 mm Outside dia. of outer ring D 30 - 90 mm CFKR CFKR … UUR CFKR … UU

Identification number Mass Boundary dimensions　mm Mounting Maximum Basic Basic Maximum
Stud (Ref.) dimension tightening dynamic static load allowable
torque load rating rating static load
diameter f
Shield type Sealed type B B1 (1) C C0
D C d1 G G1 B2 B3 C1 g1 g2 H rs min Min. 　
mm Crowned outer ring Cylindrical outer ring Crowned outer ring Cylindrical outer ring g max max mm N-m N N N
CFKR 22 R CFKR 22 CFKR 22 UUR CFKR 22 UU 43 22
10 12 10 M10×1.0 12 13.2 36.2 23 ─ 0.6 3 ─ 5 0.3 16 13.0 5 430 6 890 6 890
CFKR 26 R CFKR 26 CFKR 26 UUR CFKR 26 UU 58 26

CFKR 30 R CFKR 30 CFKR 30 UUR CFKR 30 UU 94 30

12 14 12 M12×1.5 13 15.2 40.2 25 6 0.6 4 3 6 0.6 21 21.9 7 910 9 790 9 790
CFKR 32 R CFKR 32 CFKR 32 UUR CFKR 32 UU 104 32
16 CFKR 35 R CFKR 35 CFKR 35 UUR CFKR 35 UU 165 35 18 16 M16×1.5 17 19.6 52.1 32.5 8 0.8 4 3 8 0.6 26 58.5 12 000 18 300 18 300
18 CFKR 40 R CFKR 40 CFKR 40 UUR CFKR 40 UU 248 40 20 18 M18×1.5 19 21.6 58.1 36.5 8 0.8 6 3 8 1 29 86.2 14 800 25 200 25 200
CFKR 47 R CFKR 47 CFKR 47 UUR CFKR 47 UU 378 47
20 24 20 M20×1.5 21 25.6 66.1 40.5 9 0.8 6 4 10 1 34 119 20 700 34 600 34 600
CFKR 52 R CFKR 52 CFKR 52 UUR CFKR 52 UU 453 52

24
CFKR 62 R
CFKR 72 R
CFKR 62
CFKR 72
CFKR 62 UUR
CFKR 72 UUR
CFKR 62 UU
CFKR 72 UU
795
1 120
62
72
29 24 M24×1.5 25 30.6 80.1 49.5 11 0.8 6 4 14 1 40 215 30 500 52 600 52 000 I
CFKR 80 R CFKR 80 CFKR 80 UUR CFKR 80 UU 1 860 80
30 CFKR 85 R CFKR 85 CFKR 85 UUR CFKR 85 UU 2 020 85 35 30 M30×1.5 32 37 100 63 15 1 6 4 14 1 49 438 45 400 85 100 85 100
CFKR 90 R CFKR 90 CFKR 90 UUR CFKR 90 UU 2 210 90

Note(1)　　Minimum allowable value of chamfer dimension r.

Remark Grease is pre-packed if the stud diameter d1 of the shield type is 10 mm or less or if the seal structure is the sealed type. Other models
are not provided with pre-packed grease. Perform proper lubrication for use.

1N=0.102kgf=0.2248lbs.
I29 1mm=0.03937inch
I30
 CAM FOLLOWERS CAM FOLLOWERS
Double Hex Hole Cam Followers Full Complement Type

C C
B3 r r
Grease nipple
Grease nipple g2

f
g1

g1
D
D

G
H H H H

d1

d1
G1 G1
C1 C1

B B2 B B2 R= 500
B1 B1

Stud dia.10－ 30mm Outside dia. of outer ring D 22, 26 mm Outside dia. of outer ring D 30 - 90 mm CFKR … V CFKR … VUUR CFKR … VUU

Identification number Mass Boundary dimensions　mm Mounting Maximum Basic Basic Maximum
(Ref.) dimension tightening dynamic static load allowable
Stud
torque load rating rating static load
diameter f
Shield type Sealed type B B1 (1) C C0
D C d1 G G1 B2 B3 C1 g1 g2 H rs min Min. 　
mm Crowned outer ring Cylindrical outer ring Crowned outer ring Cylindrical outer ring g max max mm N-m N N N

CFKR 22 VR CFKR 22 V CFKR 22 VUUR CFKR 22 VUU 44 22

10 12 10 M10×1.0 12 13.2 36.2 23 ─ 0.6 3 ─ 5 0.3 16 13.0 9 570 14 500 7 920
CFKR 26 VR CFKR 26 V CFKR 26 VUUR CFKR 26 VUU 59 26

CFKR 30 VR CFKR 30 V CFKR 30 VUUR CFKR 30 VUU 96 30

12 14 12 M12×1.5 13 15.2 40.2 25 6 0.6 4 3 6 0.6 21 21.9 13 500 19 700 13 200
CFKR 32 VR CFKR 32 V CFKR 32 VUUR CFKR 32 VUU 106 32
16 CFKR 35 VR CFKR 35 V CFKR 35 VUUR CFKR 35 VUU 168 35 18 16 M16×1.5 17 19.6 52.1 32.5 8 0.8 4 3 8 0.6 26 58.5 20 700 37 600 23 200
18 CFKR 40 VR CFKR 40 V CFKR 40 VUUR CFKR 40 VUU 253 40 20 18 M18×1.5 19 21.6 58.1 36.5 8 0.8 6 3 8 1 29 86.2 25 300 51 300 31 100
CFKR 47 VR CFKR 47 V CFKR 47 VUUR CFKR 47 VUU 383 47
20 24 20 M20×1.5 21 25.6 66.1 40.5 9 0.8 6 4 10 1 34 119 33 200 64 500 37 500
CFKR 52 VR CFKR 52 V CFKR 52 VUUR CFKR 52 VUU 458 52

24
CFKR 62 VR
CFKR 72 VR
CFKR 62 V
CFKR 72 V
CFKR 62 VUUR
CFKR 72 VUUR
CFKR 62 VUU
CFKR 72 VUU
800 62
1 120 72
29 24 M24×1.5 25 30.6 80.1 49.5 11 0.8 6 4 14 1 40 215 46 600 92 000 52 000 I
CFKR 80 VR CFKR 80 V CFKR 80 VUUR CFKR 80 VUU 1 860 80
30 CFKR 85 VR CFKR 85 V CFKR 85 VUUR CFKR 85 VUU 2 020 85 35 30 M30×1.5 32 37 100 63 15 1 6 4 14 1 49 438 67 700 144 000 85 900
CFKR 90 VR CFKR 90 V CFKR 90 VUUR CFKR 90 VUU 2 210 90

Note(1)　　Minimum allowable value of chamfer dimension r.

Remark    Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I31 1mm=0.03937inch
I32
 CAM FOLLOWERS
Solid Eccentric Stud Type Cam Followers With Cage/With Hexagon Hole
C
C r r r r

ε（Eccentricity）
B3

ε (Eccentricity)

ε (Eccentricity)

r
r

r
g2

f
g1
G
D

G
H

d1
G1 H

d1
C1
B B1 C1 G1
R=500 B2 B1
R= 500 B R= 500
B2

CFES … BR CFES … BR CFES … B CFES … BUU

Stud dia. 6−18mm Stud dia. d1　6-10mm Stud dia. d1　12-18mm

Identification number Mass Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
Stud (Ref.) Eccentricity dimension tightening load rating load rating allowable
dia. f torque
C C0
static load
Shield type
With crowned With cylindrical With crowned
Sealed type
With cylindrical D C d1 G G1 B B1 B2 B3 C1 g1 g2 H rs min
(1) ε Min. 　
mm outer ring outer ring outer ring outer ring g max max N
mm N-m N N

6 CFES 6 BR CFES 6 B CFES 6 BUUR CFES 6 BUU 18.5 16 11 6 M 6×1 8 12.2 28.2 16 ─ 0.6 ─ ─ 3 0.3 0.25 11 2.7 3 660 3 650 1 980
8 CFES 8 BR CFES 8 B CFES 8 BUUR CFES 8 BUU 28.5 19 11 8 M 8×1.25 10 12.2 32.2 20 ─ 0.6 ─ ─ 4 0.3 0.25 13 6.5 4 250 4 740 4 670
CFES 10 BR CFES 10 B CFES 10 BUUR CFES 10 BUU 45 22 12 10 M10×1.25 12 13.2 36.2 23 ─ 0.6 ─ ─ 4 0.3 0.3 16 13.8 5 430 6 890 6 890
10
CFES 10-1 BR CFES 10-1 B CFES 10-1 BUUR CFES 10-1 BUU 60 26 12 10 M10×1.25 12 13.2 36.2 23 ─ 0.6 ─ ─ 4 0.3 0.3 16 13.8 5 430 6 890 6 890

12 CFES 12 BR CFES 12 B CFES 12 BUUR CFES 12 BUU 95 30 14 12 M12×1.5 13 15.2 40.2 25 6 0.6 4 3 6 0.6 0.4 21 21.9 7 910 9 790 9 790
CFES 12-1 BR CFES 12-1 B CFES 12-1 BUUR CFES 12-1 BUU 105 32 14 12 M12×1.5 13 15.2 40.2 25 6 0.6 4 3 6 0.6 0.4 21 21.9 7 910 9 790 9 790
16 CFES 16 BR CFES 16 B CFES 16 BUUR CFES 16 BUU 170 35 18 16 M16×1.5 17 19.6 52.1 32.5 8 0.8 4 3 6 0.6 0.5 26 58.5 12 000 18 300 18 300
18 CFES 18 BR CFES 18 B CFES 18 BUUR CFES 18 BUU 250 40 20 18 M18×1.5 19 21.6 58.1 36.5 8 0.8 6 3 8 1 0.6 29 86.2 14 800 25 200 25 200

Note(1)　　 Minimum allowable value of chamfer dimension r

Remarks1.   Models with a stud diameter d1 of 10 mm or less have an oil hole (re-greasing fitting) at the head. Other models are provided with
an oil hole (grease nipple) at the head and an oil hole each on the outside surface and end surface of the stud.
2.   Shield type models with a stud diameter d1 of 10 mm or less and the sealed type models are provided with prepacked grease.
Other models are not provided with prepacked grease. Perform proper lubrication for use.

1N=0.102kgf=0.2248lbs.
I33 1mm=0.03937inch
I34
 CAM FOLLOWERS
Eccentric Type Cam Followers With Cage/With Hexagon Hole

C
C

ε (Eccentricity)
r r

ε (Eccentricity)

f
r
g1
de
D

de
G

G
H H
B3 G1 B3 G1
C1 R=500 C1
B B2
B B2
R= 500 B1 B1

CFE … BR CFE … BR CFE … B CFE … BUU

Outside diameter of eccentric collar de　9-13mm Outside diameter of eccentric collar de　16-41mm
Outside diameter of eccentric collar 9−41mm
Identification number Mass Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum

Eccentricity
Outside
diameter of (Ref.) dimension tightening load rating load rating allowable
eccentric
Shield type Sealed type
f torque
C C0
static load
(1)
collar With crowned With cylindrical With crowned With cylindrical D C de G B3 B B1 B2 C1 g1 G1 H rs min Min. 　
mm outer ring outer ring outer ring outer ring g max max ε mm N-m N N N

9 CFE 6 BR CFE 6 B CFE 6 BUUR CFE 6 BUU 20.5 16 11 9 M 6×1 7.5 12.2 28.2 16 0.6 ─ 8.5 3 0.3 0.4 11 2.7 3 660 3 650 1 950
11 CFE 8 BR CFE 8 B CFE 8 BUUR CFE 8 BUU 32 19 11 11 M 8×1.25 9.5 12.2 32.2 20 0.6 ─ 10.5 4 0.3 0.4 13 6.5 4 250 4 740 4 620
CFE 10 BR CFE 10 B CFE 10 BUUR CFE 10 BUU 49.5 22 12 13 M10×1.25 10.5 13.2 36.2 23 0.6 ─ 12.5 4 0.3 0.4 16 13.8 5 430 6 890 6 890
13
CFE 10-1 BR CFE 10-1 B CFE 10-1 BUUR CFE 10-1 BUU 65 26 12 13 M10×1.25 10.5 13.2 36.2 23 0.6 ─ 12.5 4 0.3 0.4 16 13.8 5 430 6 890 6 890

16 CFE 12 BR CFE 12 B CFE 12 BUUR CFE 12 BUU 105 30 14 16 M12×1.5 11.5 15.2 40.2 25 0.6 4 13.5 6 0.6 0.8 21 21.9 7 910 9 790 9 790
CFE 12-1 BR CFE 12-1 B CFE 12-1 BUUR CFE 12-1 BUU 115 32 14 16 M12×1.5 11.5 15.2 40.2 25 0.6 4 13.5 6 0.6 0.8 21 21.9 7 910 9 790 9 790
22 CFE 16 BR CFE 16 B CFE 16 BUUR CFE 16 BUU 190 35 18 22 M16×1.5 15.5 19.6 52.1 32.5 0.8 4 17 6 0.6 0.8 26 58.5 12 000 18 300 18 300
24 CFE 18 BR CFE 18 B CFE 18 BUUR CFE 18 BUU 280 40 20 24 M18×1.5 17.5 21.6 58.1 36.5 0.8 6 19 8 1 0.8 29 86.2 14 800 25 200 25 200

27
CFE 20 BR
CFE 20-1 BR
CFE 20 B
CFE 20-1 B
CFE 20 BUUR
CFE 20-1 BUUR
CFE 20 BUU 500
CFE 20-1 BUU 425
52
47
24
24
27
27
M20×1.5 19.5 25.6 66.1 40.5 0.8
M20×1.5 19.5 25.6 66.1 40.5 0.8
6 21
6 21
8 1
8 1
0.8
0.8
34
34
119
119
20 700 34 600 34 600
20 700 34 600 34 600
I
CFE 24 BR CFE 24 B CFE 24 BUUR CFE 24 BUU 895 62 29 33 M24×1.5 25.5 30.6 80.1 49.5 0.8 6 24 12 1 0.8 40 215 30 500 52 600 52 000
33
CFE 24-1 BR CFE 24-1 B CFE 24-1 BUUR CFE 24-1 BUU 1 220 72 29 33 M24×1.5 25.5 30.6 80.1 49.5 0.8 6 24 12 1 0.8 40 215 30 500 52 600 52 000
CFE 30 BR CFE 30 B CFE 30 BUUR CFE 30 BUU 2 030 80 35 41 M30×1.5 32.5 37 100 63 1 6 30.5 17 1 1.5 49 438 45 400 85 100 85 100
41 CFE 30-1 BR CFE 30-1 B CFE 30-1 BUUR CFE 30-1 BUU 2 190 85 35 41 M30×1.5 32.5 37 100 63 1 6 30.5 17 1 1.5 49 438 45 400 85 100 85 100
CFE 30-2 BR CFE 30-2 B CFE 30-2 BUUR CFE 30-2 BUU 2 380 90 35 41 M30×1.5 32.5 37 100 63 1 6 30.5 17 1 1.5 49 438 45 400 85 100 85 100

Note(1)　　 Minimum allowable value of chamfer dimension r

Remarks1.   Models with a thread diameter G of 10 mm or less have an oil hole (re-greasing fitting) at the head. Other models are provided with
an oil hole (grease nipple) at the head and an oil hole on the end surface of the stud.
2.   Shield type models with a stud thread diameter G of 10 mm or less and the sealed type models are provided with prepacked
grease. Other models are not provided with prepacked grease. Perform proper lubrication for use.

1N=0.102kgf=0.2248lbs.
I35 1mm=0.03937inch
I36
 CAM FOLLOWERS
Eccentric Type Cam Followers Full Complement Type/With Hexagon Hole

C
C
r r

ε(Eccentricity)

ε (Eccentricity)

f
r

r
g1
de

de
G
D

G
H H
B3 G1
B3 G1
C1 R=500 C1
B B2
B B2
R=500 B1
B1

CFE … VBR CFE … VBR CFE … VB CFE … VBUU

Outside diameter of eccentric collar de　9-13mm Outside diameter of eccentric collar de　16-41mm
Outside diameter of eccentric collar 9−41mm
Identification number Mass Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum

Eccentricity
Outside
diameter of (Ref.) dimension tightening load rating load rating allowable
eccentric
Shield type Sealed type f torque
C C0
static load
(1)
collar With crowned With cylindrical With crowned With cylindrical D C de G B3 B B1 B2 C1 g1 G1 H rs min Min. 　
mm outer ring outer ring outer ring outer ring g max max ε N N
mm N-m N

9 CFE 6 VBR CFE 6 VB CFE 6 VBUUR CFE 6 VBUU 21 16 11 9 M 6×1 7.5 12.2 28.2 16 0.6 ─ 8.5 3 0.3 0.4 11 2.7 6 980 8 500 1 950
11 CFE 8 VBR CFE 8 VB CFE 8 VBUUR CFE 8 VBUU 32.5 19 11 11 M 8×1.25 9.5 12.2 32.2 20 0.6 ─ 10.5 4 0.3 0.4 13 6.5 8 170 11 200 4 620
CFE 10 VBR CFE 10 VB CFE 10 VBUUR CFE 10 VBUU 50.5 22 12 13 M10×1.25 10.5 13.2 36.2 23 0.6 ─ 12.5 4 0.3 0.4 16 13.8 9 570 14 500 8 650
13
CFE 10-1 VBR CFE 10-1 VB CFE 10-1 VBUUR CFE 10-1 VBUU 66 26 12 13 M10×1.25 10.5 13.2 36.2 23 0.6 ─ 12.5 4 0.3 0.4 16 13.8 9 570 14 500 8 650

16 CFE 12 VBR CFE 12 VB CFE 12 VBUUR CFE 12 VBUU 107 30 14 16 M12×1.5 11.5 15.2 40.2 25 0.6 4 13.5 6 0.6 0.8 21 21.9 13 500 19 700 13 200
CFE 12-1 VBR CFE 12-1 VB CFE 12-1 VBUUR CFE 12-1 VBUU 117 32 14 16 M12×1.5 11.5 15.2 40.2 25 0.6 4 13.5 6 0.6 0.8 21 21.9 13 500 19 700 13 200
22 CFE 16 VBR CFE 16 VB CFE 16 VBUUR CFE 16 VBUU 193 35 18 22 M16×1.5 15.5 19.6 52.1 32.5 0.8 4 17 6 0.6 0.8 26 58.5 20 700 37 600 23 200
24 CFE 18 VBR CFE 18 VB CFE 18 VBUUR CFE 18 VBUU 285 40 20 24 M18×1.5 17.5 21.6 58.1 36.5 0.8 6 19 8 1 0.8 29 86.2 25 300 51 300 31 100

27
CFE 20 VBR CFE 20 VB CFE 20 VBUUR CFE 20 VBUU 505
CFE 20-1 VBR CFE 20-1 VB CFE 20-1 VBUUR CFE 20-1 VBUU 430
52
47
24
24
27
27
M20×1.5
M20×1.5
19.5 25.6 66.1 40.5 0.8
19.5 25.6 66.1 40.5 0.8
6 21
6 21
8 1
8 1
0.8
0.8
34
34
119
119
33 200 64 500 37 500
33 200 64 500 37 500
I
CFE 24 VBR CFE 24 VB CFE 24 VBUUR CFE 24 VBUU 900 62 29 33 M24×1.5 25.5 30.6 80.1 49.5 0.8 6 24 12 1 0.8 40 215 46 600 92 000 52 000
33
CFE 24-1 VBR CFE 24-1 VB CFE 24-1 VBUUR CFE 24-1 VBUU 1 220 72 29 33 M24×1.5 25.5 30.6 80.1 49.5 0.8 6 24 12 1 0.8 40 215 46 600 92 000 52 000
CFE 30 VBR CFE 30 VB CFE 30 VBUUR CFE 30 VBUU 2 030 80 35 41 M30×1.5 32.5 37 100 63 1 6 30.5 17 1 1.5 49 438 67 700 144 000 85 900
41 CFE 30-1 VBR CFE 30-1 VB CFE 30-1 VBUUR CFE 30-1 VBUU 2 190 85 35 41 M30×1.5 32.5 37 100 63 1 6 30.5 17 1 1.5 49 438 67 700 144 000 85 900
CFE 30-2 VBR CFE 30-2 VB CFE 30-2 VBUUR CFE 30-2 VBUU 2 380 90 35 41 M30×1.5 32.5 37 100 63 1 6 30.5 17 1 1.5 49 438 67 700 144 000 85 900

Note(1)　　 Minimum allowable value of chamfer dimension r

Remarks1.   Models with a thread diameter G of 10 mm or less have an oil hole (re-greasing fitting) at the head. Other models are provided with
an oil hole (grease nipple) at the head and an oil hole on the end surface of the stud.
2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I37 1mm=0.03937inch
I38
 CAM FOLLOWERS
Thrust Disk Type Cam Followers With Cage/With Hexagon Hole
C C
B3
g2

f
g1
D

G
D

G
H H

d1

d1
G1 G1
C1 C1

R＝500 B B2 R=500 B B2
B1 B1

CF … WBR CF … WBR
Stud dia. 3－ 20mm Stud dia. d1　3-10mm Stud dia. d1　12-20mm
CF … WBUUR

Identification number Mass Mounting Maximum Basic dynamic Basic static Maximum
　　　　　　　　Boundary dimensions　mm
(Ref.) dimension tightening load rating load rating allowable
Stud dia. f torque
C C0
static load
Shield type Sealed type
D C d1 G G1 B B1 B2 B3 C1 g1 g2 H Min. 　
mm g mm N-m N N N

3 CF 3 WBR CF 3 WBUUR 4.3 10 7 3 M 3 × 0.5 5 8 17 9 ─ 0.5 ─ ─ 2 6.8 0.34 1 500 1 020 384

4 CF 4 WBR CF 4 WBUUR 7.4 12 8 4 M 4 × 0.7 6 9 20 11 ─ 0.5 ─ ─ 2.5 8.3 0.78 2 070 1 590 834

5 CF 5 WBR CF 5 WBUUR 10.3 13 9 5 M 5 × 0.8 7.5 10 23 13 ─ 0.5 ─ ─ 3 9.3 1.6 2 520 2 140 1 260

12.2 28.2
6 CF 6 WBR CF 6 WBUUR 18.5 16 11  6 M 6×1 　8 16 ─ 0.6 ─ ─ 3 11 2.7 3 660 3 650 1 950
max max
12.2 32.2
M 8 × 1.25 10 ─ ─ ─
8 CF 8 WBR CF 8 WBUUR
I
28.5 19 11  8 20 0.6 4 13 6.5 4 250 4 740 4 620
max max
CF 10 WBR CF 10 WBUUR 45 22 12 10 M10 × 1.25 12 13.2 36.2 23 ─ 0.6 ─ ─ 4 16 13.8 5 430 6 890 6 890
max max 　
10
CF 10-1 WBR CF 10-1 WBUUR 60 26 12 10 M10 × 1.25 12 13.2 36.2 23 ─ 0.6 ─ ─ 4 16 13.8 5 430 6 890 6 890
max max
CF 12 WBR CF 12 WBUUR 95 30 14 12 M12 × 1.5 13 15.2 40.2 25 6 0.6 4 3 6 21 21.9 7 910 9 790 9 790
max max
12
CF 12-1 WBR CF 12-1 WBUUR 105 32 14 12 M12 × 1.5 13 15.2 40.2 25 6 0.6 4 3 6 21 21.9 7 910 9 790 9 790
max max
19.6 52.1 32.5 8 0.8 4 3 6 26 58.5 12 000 18 300 18 300
16 CF 16 WBR CF 16 WBUUR 170 35 18 16 M16 × 1.5 17 max max
21.6 58.1 36.5 8 0.8 6 3 8 29 86.2 14 800 25 200 25 200
18 CF 18 WBR CF 18 WBUUR 250 40 20 18 M18 × 1.5 19
max max

CF 20 WBR CF 20 WBUUR 460 52 24 20 M20 × 1.5 21 25.6 66.1 40.5 9 0.8 6 4 8 34 119 20 700 34 600 34 600
max max
20
CF 20-1 WBR CF 20-1 WBUUR 385 47 24 20 M20 × 1.5 21 25.6 66.1 40.5 9 0.8 6 4 8 34 119 20 700 34 600 34 600
max max
Remarks1.   Models with a stud diameter d1 of 4 mm or less have no oil hole. For Models with a stud dia. 5 to 10 mm, oil hole (re-greasing
fitting) is provided at the head. Other models are provided with an oil hole (grease nipple) at the head and an oil hole each on the
outside surface and end surface of the stud.
2.   Shield type models with a stud diameter d1 of 10 mm or less and the sealed type models are provided with prepacked grease.
Other models are not provided with prepacked grease. Perform proper lubrication for use.

1N=0.102kgf=0.2248lbs.
I39 1mm=0.03937inch
I40
 CAM FOLLOWERS
Thrust Disk Type Cam Followers / Stainless Steel Made With Cage/With Hexagon Hole

f
Stud dia. 3−5mm
CF … FWBR CF … FWBUUR

Identification number Mass Mounting Maximum Basic dynamic Basic static Maximum
　　　　　　　　Boundary dimensions　mm
(Ref.) dimension tightening load rating load rating allowable
Stud dia. f torque
C C0
static load
Shield type Sealed type
D C d1 G G1 B B1 B2 B3 C1 g1 g2 H Min. 　
mm g mm N-m N N N

3 CF 3 FWBR CF 3 FWBUUR 4.3 10 7 3 M 3 × 0.5 5 8 17 9 ─ 0.5 ─ ─ 2 6.8 0.34 1 200 813 384

4 CF 4 FWBR CF 4 FWBUUR 7.4 12 8 4 M 4 × 0.7 6 9 20 11 ─ 0.5 ─ ─ 2.5 8.3 0.78 1 650 1 270 834

5 CF 5 FWBR CF 5 FWBUUR 10.3 13 9 5 M 5 × 0.8 7.5 10 23 13 ─ 0.5 ─ ─ 3 9.3 1.6 1 930 1 730 1 260

Remarks1.   Models with a stud diameter d1 of 4 mm or less have no oil hole. For Models with a stud dia. 5 mm, oil hole (re-greasing fitting) is
provided at the head.
2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I41 1mm=0.03937inch
I42
 CAM FOLLOWERS
Centralized Lubrication Type Cam Followers With Cage/With Screwdriver Slot

Stud dia. 6−30mm CF-RU1 CF-FU1

Identification number Mass 　　　　　　　　Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
(Ref.) dimension tightening load rating load rating allowable
Stud dia. f torque
C C0
static load
With crowned With cylindrical (1) Min. 　
outer ring outer ring g
D C d1 G G1 B B1 B2 B3 C1 g2 M1 M2 rs min
mm max max mm N-m N N N

6 CF-RU1- 6 CF-FU1- 6 18.5 16 11 6 M 6×1 8 12.2 28.2 16 ─ 0.6 ─ 0.3 11 2.7 3 660 3 650 1 950
8 CF-RU1- 8 CF-FU1- 8 28.5 19 11 8 M 8 × 1.25 10 12.2 32.2 20 ─ 0.6 ─ 0.3 13 6.5 4 250 4 740 4 620
CF-RU1-10 CF-FU1-10 45 22 12 10 M10 × 1.25 12 13.2 36.2 23 ─ 0.6 ─ M6× 0.3 16 13.8 5 430 6 890 6 890
10 0.75 ─
CF-RU1-10-1 CF-FU1-10-1 60 26 12 10 M10 × 1.25 12 13.2 36.2 23 ─ 0.6 ─ 0.3 16 13.8 5 430 6 890 6 890
CF-RU1-12 CF-FU1-12 95 30 14 12 M12 × 1.5 13 15.2 40.2 25 ─ 0.6 ─ 0.6 21 23.9 7 910 9 790 9 790
12
CF-RU1-12-1 CF-FU1-12-1 105 32 14 12 M12 × 1.5 13 15.2 40.2 25 ─ 0.6 ─ 0.6 21 23.9 7 910 9 790 9 790
16 CF-RU1-16 CF-FU1-16 170 35 18 16 M16 × 1.5 17 19.6 52.1 32.5 8 0.8 3 0.6 26 58.5 12 000 18 300 18 300
18 CF-RU1-18 CF-FU1-18 250 40 20 18 M18 × 1.5 19 21.6 58.1 36.5 8 0.8 3 1 29 86.2 14 800 25 200 25 200

20
CF-RU1-20
CF-RU1-20-1
CF-FU1-20
CF-FU1-20-1
460
385
52
47
24
24
20
20
M20 × 1.5
M20 × 1.5
21
21
25.6
25.6
66.1 40.5
66.1 40.5
9
9
0.8
0.8
4
4
1
1
34
34
119
119
20 700
20 700
34 600
34 600
34 600
34 600
I
PT PT
CF-RU1-24 CF-FU1-24 815 62 29 24 M24 × 1.5 25 30.6 80.1 49.5 11 0.8 4 1/8 1/8 1 40 215 30 500 52 600 52 000
24
CF-RU1-24-1 CF-FU1-24-1 1 140 72 29 24 M24 × 1.5 25 30.6 80.1 49.5 11 0.8 4 1 40 215 30 500 52 600 52 000
CF-RU1-30 CF-FU1-30 1 870 80 35 30 M30 × 1.5 32 37 100 63 15 1 4 1 49 438 45 400 85 100 85 100
30 CF-RU1-30-1 CF-FU1-30-1 2 030 85 35 30 M30 × 1.5 32 37 100 63 15 1 4 1 49 438 45 400 85 100 85 100
CF-RU1-30-2 CF-FU1-30-2 2 220 90 35 30 M30 × 1.5 32 37 100 63 15 1 4 1 49 438 45 400 85 100 85 100

Note(1)　　 Minimum allowable value of chamfer dimension r

Remarks1.   Models with a stud diameter d1 of 12 mm or less are provided with a lubrication tapped hole on the stud head only. Other models
are provided with one lubrication tapped hole each on the head and end surface of the stud.
2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I43 1mm=0.03937inch
I44
 CAM FOLLOWERS
Easy Mounting Type Cam Followers With Cage/With Hexagon Hole
t
C C1
C C1 h
r L1 L2
r L1 L2

r
r
H H

D1
d1
D
d1
°
90

°
90
e

f
B B2
B B2
B1
B1

CF-SFU … B CF-SFU … B
Stud dia. 6−20mm Stud dia. d1　6-10mm Stud dia. d1　12-20mm

Mass 　　　　　　　　　　　　　Boundary dimensions　mm Mounting dimensions　mm Basic dynamic Basic static Maximum
(Ref.) load rating load rating allowable
Identification static load
Stud dia.
number C C0
(1) t f h
D C d1 B B1 B2 C1 L1 L2 H e rs min D1 　
mm g max max Tolerance Min. Min. (Ref.) N N N

＋ 0.012
6 CF-SFU- 6 B 19.5 16 11 6 12.2 32 19.8 0.6 5 10 3 0.3 0.3 6 20 11 10 3 660 3 650 1 950
  0
8 CF-SFU-   8 B 29 19 11 8 12.2 32 19.8 0.6 5 10 4 0.5 0.3 8 20 13 10 4 250 4 740 4 620
＋ 0.015
CF-SFU-10 B 44 22 12 10 13.2 33 19.8 0.6 5 10 4 0.5 0.3 10   0 20 16 10 5 430 6 890 6 890
10
CF-SFU-10-1 B 59 26 12 10 13.2 33 19.8 0.6 5 10 4 0.5 0.3 10 20 16 10 5 430 6 890 6 890
CF-SFU-12 B 94 30 14 12 15.2 35 19.8 0.6 5 10 6 1 0.6 12 20 21 10 7 910 9 790 9 790
12
CF-SFU-12-1 B 104 32 14 12 15.2 35 19.8 0.6 5 10 6 1 0.6 12
＋ 0.018
20 21 10 7 910 9 790 9 790
16 CF-SFU-16 B 164 35 18 16 19.6 44.5 24.9 0.8 10 10 6 1 0.6 16   0 25 26 15 12 000 18 300 18 300
18 CF-SFU-18 B
CF-SFU-20 B
235
435
40
52
20
24
18
20
21.6
25.6
46.5
50.5
24.9
24.9
0.8
0.8
10
10
10
10
8
8
1
1
1
1
18
20 ＋ 0.021
25
25
29
34
15
15
14 800
20 700
25 200
34 600
25 200
34 600
I
20
CF-SFU-20-1 B 360 47 24 20 25.6 50.5 24.9 0.8 10 10 8 1 1 20   0 25 34 15 20 700 34 600 34 600

Note(1)　　 Minimum allowable value of chamfer dimension r

Remarks1.   Models with a stud diameter d1 of 10 mm or less have an oil hole (re-greasing fitting) at the head. Other models are provided with
an oil hole (grease nipple) at the head.
2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I45 1mm=0.03937inch
I46
 CAM FOLLOWERS
Cam Follower G With Cage/With Hexagon Hole C
r

f
D

G
H

d1
G1
C1
B B2
B1

Stud dia. 6 −20mm CF … G

Mass 　　　　　　　　　　　　　Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
(Ref.) dimension tightening load rating load rating allowable static
Identification
Stud dia.
number
f torque
C C0
load

D C d1 G G1 B B1 B2 C1 H
(1)
rs min Min. 　
mm g max max mm N-m N N N

6 CF 6 G 19.5 16 11 6 M 6×1 8 12.2 28.2 16 0.6 3 0.3 11 2.7 3 660 3 650 1 950
8 CF 8 G 29.5 19 11 8 M 8 × 1.25 10 12.2 32.2 20 0.6 4 0.3 13 6.5 4 250 4 740 4 620
CF 10 G 47.5 22 12 10 M10 × 1.25 12 13.2 36.2 23 0.6 4 0.3 16 13.8 5 430 6 890 6 890
10
CF 10-1 G 61.5 26 12 10 M10 × 1.25 12 13.2 36.2 23 0.6 4 0.3 16 13.8 5 430 6 890 6 890
CF 12 G 95.0 30 14 12 M12 × 1.5 13 15.2 40.2 25 0.6 6 0.6 21 23.9 7 910 9 790 9 790
12
CF 12-1 G 105 32 14 12 M12 × 1.5 13 15.2 40.2 25 0.6 6 0.6 21 23.9 7 910 9 790 9 790
16 CF 16 G 175 35 18 16 M16 × 1.5 17 19.6 52.1 32.5 0.8 6 0.6 26 61.1 12 000 18 300 18 300
M18 × 1.5
I
18 CF 18 G 255 40 20 18 19 21.6 58.1 36.5 0.8 8 1 29 89.2 14 800 25 200 25 200
CF 20 G 470 52 24 20 M20 × 1.5 21 25.6 66.1 40.5 0.8 8 1 34 125 20 700 34 600 34 600
20
CF 20-1 G 400 47 24 20 M20 × 1.5 21 25.6 66.1 40.5 0.8 8 1 34 125 20 700 34 600 34 600

Note(1)　　 Minimum allowable value of chamfer dimension r.

Remarks1.   This bearing cannot be re-lubricated due to its structure. If re-lubrication is necessary, please use Standard Type Cam
Followers.
Remarks2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I47 1mm=0.03937inch
I48
 CAM FOLLOWERS
C-Lube Cam Followers With Cage / With Hexagon Hole
C

G
d1
G1
C1
R=500
B B2
B1

Stud dia. 5 − 20mm CF … WB … /SG

Mass Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
Stud (Ref.) dimension tightening load rating load rating allowable
dia. Identification number f torque
C C0
static load

D C d1 G G1 B B1 B2 C1 H Min. 　
mm g
mm N-m N N N
5 CF 5  WBUUR/SG 10.3 13 9 5 M 5 × 0.8 7.5 10 23 13 0.5 3 9.3 1.6 2 520 2 140 1 260
6 CF 6  WBUUR/SG 18.5 16 11 6 M 6×1 8 12.2 max 28.2 max 16 0.6 3 11 2.7 3 660 3 650 1 950
8 CF 8  WBUUR/SG 28.5 19 11 8 M 8 × 1.25 10 12.2 max 32.2 max 20 0.6 4 13 6.5 4 250 4 740 4 620
CF 10 WBUUR/SG 45 22 12 10 M10 × 1.25 12 13.2 max 36.2 max 23 0.6 4 16 13.8 5 430 6 890 6 890
10
CF 10-1 WBUUR/SG 60 26 12 10 M10 × 1.25 12 13.2 max 36.2 max 23 0.6 4 16 13.8 5 430 6 890 6 890
CF 12 WBUUR/SG 95 30 14 12 M12 × 1.5 13 15.2 max 40.2 max 25 0.6 6 21 21.9 7 910 9 790 9 790
12
CF 12-1 WBUUR/SG 105 32 14 12 M12 × 1.5 13 15.2 max 40.2 max 25 0.6 6 21 21.9 7 910 9 790 9 790
16 CF 16 WBUUR/SG 170 35 18 16 M16 × 1.5 17 19.6 max 52.1 max 32.5 0.8 6 26 58.5 12 000 18 300 18 300
18 CF 18 WBUUR/SG 250 40 20 18 M18 × 1.5 19 21.6 max 58.1 max 36.5 0.8 8 29 86.2 14 800 25 200 25 200
I
CF 20 WBUUR/SG 460 52 24 20 M20 × 1.5 21 25.6 max 66.1 max 40.5 0.8 8 34 119 20 700 34 600 34 600
20
CF 20-1 WBUUR/SG 385 47 24 20 M20 × 1.5 21 25.6 max 66.1 max 40.5 0.8 8 34 119 20 700 34 600 34 600

Remark　This bearing cannot be re-lubricated as thermosetting solid-type lubricant C-Lube fills its inner space.

1N=0.102kgf=0.2248lbs.
I49 1mm=0.03937inch
I50
 CAM FOLLOWERS
Miniature Type Cam Followers With Cage/With Hexagon Hole
Full Complement Type/With Hexagon Hole

Stud dia. 2−6mm CFS CFS … V

Identification number Mass 　　　　　　　　　　　　　Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
(Ref.) dimension tightening load rating load rating allowable
Stud dia. f torque
C C0
static load
With cage Full complement
D C d1 G G1 B B1 B2 C1 H Min. 　
mm g mm N-m N N N

CFS 2 ─ 0.6 4.5 2.5 2 M2　 × 0.4 2 4   8   4 0.7 0.9 4.3 9.1 288 202 202
2
─ CFS 2　V 0.6 4.5 2.5 2 M2　 × 0.4 2 4   8   4 0.7 0.9 4.3 9.1 768 734 229
CFS 2.5 ─ 1 5 3 2.5 M2.5 × 0.45 2.5 4.5   9.5 5 0.7 0.9 4.8 18.7 428 351 351
2.5
─ CFS 2.5 V 1 5 3 2.5 M2.5 × 0.45 2.5 4.5   9.5 5 0.7 0.9 4.8 18.7 1 000 1 080 360
CFS 3 ─ 2 6 4 3 M3　 × 0.5 3 5.5 11.5 6 0.7 1.3 5.8 33.5 629 611 484
3
─ CFS 3   V 2 6 4 3 M3　 × 0.5 3 5.5 11.5 6 0.7 1.3 5.8 33.5 1 420 1 790 484
CFS 4 ─ 4 8 5 4 M4　 × 0.7 4 7 15 8 1.0 1.5 7.7 77.7 1 120 1 120 919
4
─ CFS 4  V 4 8 5 4 M4　 × 0.7 4 7 15 8 1.0 1.5 7.7 77.7 2 370 3 000 919
CFS 5 ─ 7 10 6 5 M5　 × 0.8 5 8 18 10 1.0 2 9.6 158 1 570 1 850 1 570
5
─ CFS 5  V 7 10 6 5 M5　 × 0.8 5 8 18 10 1.0 2 9.6 158 3 180 4 700 1 570 I
CFS 6 ─ 13 12 7 6 M6　 × 1 6 9.5 21.5 12 1.2 2.5 11.6 268 2 090 2 200 2 150
6
─ CFS 6  V 13 12 7 6 M6　 × 1 6 9.5 21.5 12 1.2 2.5 11.6 268 4 610 6 250 2 150

Remarks1.   No oil hole is provided.

2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I51 1mm=0.03937inch
I52
 CAM FOLLOWERS
Miniature Type Cam Followers / Stainless Steel Made With Cage/With Hexagon Hole
Full Complement Type/With Hexagon Hole

Stud dia. 2−6mm CFS … F CFS … FV

Identification number Mass 　　　　　　　　　　　　　Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
(Ref.) dimension tightening load rating load rating allowable
Stud dia. f torque
C C0
static load
With cage Full complement
D C d1 G G1 B B1 B2 C1 H Min. 　
mm g mm N-cm N N N

CFS 2      F ─ 0.6 4.5 2.5 2 M2　 × 0.4 2 4   8 4 0.7 0.9 4.3 9.1 230 161 161
2
─ CFS 2   FV 0.6 4.5 2.5 2 M2　 × 0.4 2 4   8 4 0.7 0.9 4.3 9.1 614 587 229
CFS 2.5 F ─ 1 5 3 2.5 M2.5 × 0.45 2.5 4.5   9.5 5 0.7 0.9 4.8 18.7 342 281 281
2.5
─ CFS 2.5 FV 1 5 3 2.5 M2.5 × 0.45 2.5 4.5   9.5 5 0.7 0.9 4.8 18.7 800 862 360
CFS 3      F ─ 2 6 4 3 M3　 × 0.5 3 5.5 11.5 6 0.7 1.3 5.8 33.5 504 488 484
3
─ CFS 3   FV 2 6 4 3 M3　 × 0.5 3 5.5 11.5 6 0.7 1.3 5.8 33.5 1 140 1 430 484
CFS 4    F ─ 4 8 5 4 M4　 × 0.7 4 7 15 8 1.0 1.5 7.7 77.7 897 894 894
4
─ CFS 4  FV 4 8 5 4 M4　 × 0.7 4 7 15 8 1.0 1.5 7.7 77.7 1 900 2 400 919
CFS 5    F ─ 7 10 6 5 M5　 × 0.8 5 8 18 10 1.0 2 9.6 158 1 250 1 480 1 480
5
─ CFS 5  FV 7 10 6 5 M5　 × 0.8 5 8 18 10 1.0 2 9.6 158 2 540 3 760 1 570 I
CFS 6    F ─ 13 12 7 6 M6　 × 1 6 9.5 21.5 12 1.2 2.5 11.6 268 1 670 1 760 1 760
6
─ CFS 6  FV 13 12 7 6 M6　 × 1 6 9.5 21.5 12 1.2 2.5 11.6 268 3 690 5 000 2 150

Remarks1.   No oil hole is provided.

2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I53 1mm=0.03937inch
I54
 CAM FOLLOWERS
Thrust Disk Type Miniature Cam Followers With Cage/With Hexagon Hole
Full Complement Type/With Hexagon Hole
C

f
G
D
H

d1
G1
C1
B B2
B1

CFS … W
Stud dia. 1.4 − 6mm CFS1.4 WV

Mass 　　　　　　 Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
Identification number (Ref.) dimension tightening load rating load rating allowable
Stud dia. f torque
C C0
static load

With cage Full complement D C d1 G G1 B B1 B2 C1 H Min. 　

mm g mm N-cm N N N
1.4 ─ CFS 1.4 WV 0.35 4 1.7 1.4 M1.4 × 0.3 1.4 3.7 7 3.3 0.7 0.9 3.8 3.0 481 385 105
2 CFS 2   W ─ 0.6 4.5 2.5 2 M2 × 0.4 2 4.5 8.5 4 0.7 0.9 4.3 9.1 288 202 194
2.5 CFS 2.5 W ─ 1 5 3 2.5 M2.5 × 0.45 2.5 5 10 5 0.7 0.9 4.8 18.7 428 351 313
3 CFS 3   W ─ 2 6 4 3 M3 × 0.5 3 6.5 12.5 6 0.7 1.3 5.8 33.5 629 611 399
4 CFS 4   W ─ 4 8 5 4 M4 × 0.7 4 8 16 8 1 1.5 7.7 77.7 1120 1120 785
5 CFS 5   W ─ 7 10 6 5 M5 × 0.8 5 9 19 10 1 2 9.6 158 1570 1850 1370
6 CFS 6   W ─ 13 12 7 6 M6 ×1 6 10.5 22.5 12 1.2 2.5 11.6 268 2090 2200 1920

Remarks1. No oil hole is provided.

2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I55 1mm=0.03937inch
I56
 CAM FOLLOWERS
Thrust Disk Type Miniature Cam Followers･Stainless Steel Made With Cage/With Hexagon Hole

f
G
D
H

d1
G1
C1
B B2
B1

Stud dia. 2 − 6mm CFS … FW

Mass 　　　　　　 Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
(Ref.) dimension tightening load rating load rating allowable
Stud dia. Identification number f torque
C C0
static load

D C d1 G G1 B B1 B2 C1 H Min. 　
mm g mm N-cm N N N
2 CFS 2      FW 0.6 4.5 2.5 2 M2　 × 0.4 2 4.5 8.5 4 0.7 0.9 4.3 9.1 230 161 161
2.5 CFS 2.5 FW 1 5 3 2.5 M2.5 × 0.45 2.5 5 10 5 0.7 0.9 4.8 18.7 342 281 281
3 CFS 3      FW 2 6 4 3 M3　 × 0.5 3 6.5 12.5 6 0.7 1.3 5.8 33.5 504 488 399
4 CFS 4      FW 4 8 5 4 M4　 × 0.7 4 8 16 8 1.0 1.5 7.7 77.7 897 894 785
5 CFS 5      FW 7 10 6 5 M5　 × 0.8 5 9 19 10 1.0 2 9.6 158 1 250 1 480 1 370
6 CFS 6      FW 13 12 7 6 M6　 × 1 6 10.5 22.5 12 1.2 2.5 11.6 268 1 670 1 760 1 760

Remarks1. No oil hole is provided.

2. Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I57 1mm=0.03937inch
I58
 CAM FOLLOWERS
Cylindrical Roller Cam Followers Full Complement Type/With Hexagon Hole

C C
B3
g2

f
H H

g1
D

D
G

G
d1
d1
C1 G1 C1 G1

B B2 B B2
R=500 R=500
B1 B1

NUCF … BR NUCF … BR
Stud dia. d1　10mm Stud dia. d1　12-30mm
Stud dia. 10−30mm

Mass 　　　　　　　　　　　　　Boundary dimensions　mm Mounting Maximum Basic dynamic Basic static Maximum
(Ref.) dimension tightening load rating load rating allowable
Identification
Stud dia.
number
f torque
C C0
static load

D C d1 G G1 B B1 B2 B3 C1 g1 g2 H Min. 　
mm g max max mm N-m N N N

NUCF 10 BR 44 22 12 10 M10 × 1.25 12 13.2 36.2 23 ─ 0.6 ─ ─ 4 12 13.8 10 400 11 500 5 300
10
NUCF 10-1 BR 58 26 12 10 M10 × 1.25 12 13.2 36.2 23 ─ 0.6 ─ ─ 4 12 13.8 10 400 11 500 9 210
NUCF 12 BR 86 30 14 12 M12 × 1.5 13 15.2 40.2 25 6 0.6 4 3 6 17 21.9 14 000 13 400 5 650
12
NUCF 12-1 BR 97 32 14 12 M12 × 1.5 13 15.2 40.2 25 6 0.6 4 3 6 17 21.9 14 000 13 400 9 040
16 NUCF 16 BR 167 35 18 16 M16 × 1.5 17 19.6 52.1 32.5 8 0.8 4 3 6 20 58.5 23 400 27 300 11 800
18 NUCF 18 BR 244 40 20 18 M18 × 1.5 19 21.6 58.1 36.5 8 0.8 6 3 8 22 86.2 25 200 30 900 20 300
NUCF 20 BR 457 52 24 20 M20 × 1.5 21 25.6 66.1 40.5 9 0.8 6 4 8 31 119 43 100 58 100 30 000
20
NUCF 20-1 BR 384 47 24 20 M20 × 1.5 21 25.6 66.1 40.5 9 0.8 6 4 8 27 119 38 900 49 000 27 200

24
NUCF 24 BR
NUCF 24-1 BR
789
1 020
62
72
29
29
24
24
M24 × 1.5
M24 × 1.5
25
25
30.6
30.6
80.1
80.1
49.5
49.5
11
11
0.8
0.8
6
6
4
4
12
12
38
44
215
215
58 200
63 900
75 300
88 800
35 200
57 000 I
NUCF 30 BR 1 600 80 35 30 M30 × 1.5 32 37 100 63 15 1 6 4 17 45 438 90 300 121 000 98 300
30
NUCF 30-2 BR 1 970 90 35 30 M30 × 1.5 32 37 100 63 15 1 6 4 17 45 438 90 300 121 000 98 300

Remarks1.   For models with a stud diameter d1 of 10mm, oil hole (re-greasing fitting) is provided at the head. Other models are provided with
an oil hole (grease nipple) at the head and an oil hole each on the outside surface and end surface of the stud.
2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I59 1mm=0.03937inch
I60
 CAM FOLLOWERS
Inch Series Cam Followers With Cage/With Hexagon Hole
C

B3 r r

g2

r
r

f
g1
D

G
H

d1
G1

R=500 C1 R=500

B B2

Stud dia. 4.826 − 22.225mm CR … BR CR … B CR … BUUR CR … BUU

Identification number Mass Boundary dimensions　mm(inch) Mounting Maximum Basic dynamic Basic static
Stud (Ref.) dimension tightening load rating load rating
dia. Shield type Sealed type f torque
C C0
mm Min.
With crowned With cylindrical With crowned With cylindrical
g D C d1 G G1 B B2 B3 C1 g1 g2 H r
(inch) outer ring outer ring outer ring outer ring UNF max mm(inch) N-m N N

CR 8  BR CR 8 B CR 8 BUUR CR 8 BUU 9 12.700（ 1╱2） 8.731（ 11╱32）4.826 No.10-32 6.350（ 1╱4） 10.2（0.40） 12.700（ 1╱2） （ 1╱32）
    ─   （   ─  ） 0.794    ─   （   ─  ）    ─   （   ─  ） 3.175（ 1╱8） 0.397（ 1╱64） （ 21╱64） 1.4
8.334 2 520 2 140
4.826
CR 8-1 BR CR   8-1 B CR 8-1 BUUR CR 8-1 BUU 10 12.700（ 1╱2） 9.525（ 3╱8） 4.826 No.10-32 6.350（ 1╱4） 10.9（0.43） （ 5╱8）
15.875     ─   （   ─  ） 0.794（ ）    ─   （   ─  ）    ─   （   ─  ） 3.175（ 1╱8） 0.397（ 1╱64）
╱
1 32 8.334（ 21╱64） 1.4 2 520 2 140
6.350 CR 10 BR CR 10 B CR 10 BUUR CR 10 BUU 19 15.875（ 5╱8） 10.319（ 13╱32） 6.350（ 1╱4） 1╱4 - 28 7.938（ 5╱16） 11.8（0.46） 15.875（ 5╱8）     ─   （   ─  ） 0.794（ 1╱32）    ─   （   ─  ）    ─   （   ─  ） 3.175（ 1╱8） 0.397（ 1╱64） 11.509（ 29╱64） 3.4 3 650 3 670
（ 1╱4） CR 10-1 BR CR 10-1 B CR 10-1 BUUR CR 10-1 BUU 21 15.875（ 5╱8） 11.112（ 7╱16） 6.350（ 1╱4） 1╱4 - 28 7.938（ 5╱16） 12.5（0.49） 19.050（ 3╱4）     ─   （   ─  ） 0.794（ 1╱32）    ─   （   ─  ）    ─   （   ─  ） 3.175（ 1╱8） 0.397（ 1╱64） 11.509（ 29╱64） 3.4 3 650 3 670
9.525 CR 12 BR CR 12 B CR 12 BUUR CR 12 BUU 35 19.050（ 3╱4） 12.700（ 1╱2） 9.525（ 3╱8） 3╱8 - 24 9.525（ 3╱8） 14.2（0.56） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 4.762（ 3╱16） 0.794（ 1╱32） 13.494（ 17╱32） 10.8 4 420 5 110
（ 3╱8） CR 14 BR CR 14 B CR 14 BUUR CR 14 BUU 46 22.225（ 7╱8） 12.700（ 1╱2） 9.525（ 3╱8） 3╱8 - 24 9.525（ 3╱8） 14.2（0.56） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 4.762（ 3╱16） 0.794（ 1╱32） 15.081（ 19╱32） 10.8 4 790 5 810
11.112 CR 16 BR CR 16 B CR 16 BUUR CR 16 BUU 73 25.400（1 ） 15.875（ 5╱8） 11.112（ 7╱16） 7╱16 - 20 12.700（ 1╱2） 17.3（0.68） 25.400（1 ） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 6.350（ 1╱4） 1.191（ 3╱64） 17.859（ 45╱64） 17.4 8 810 10 800
（ 7╱16） CR 18 BR CR 18 B CR 18 BUUR CR 18 BUU 99 28.575（1 1╱8） 15.875（ 5╱8） 11.112（ 7╱16） 7╱16 - 20 12.700（ 1╱2） 17.3（0.68） 25.400（1 ） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 6.350（ 1╱4） 1.588（ 1╱16） 19.050（ 3╱4） 17.4 9 180 11 600
12.700 CR 20 BR CR 20 B CR 20 BUUR CR 20 BUU 132 31.750（1 1╱4） 19.050（ 3╱4） 12.700（ 1╱2） 1╱2 - 20 15.875（ 5╱8） 20.4（0.80） 31.750（1 1╱4） 7.938（ 5╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 6.350（ 1╱4） 1.588（ 1╱16） 21.828（ 55╱64） 27.7 14 200 16 000
（ 1╱2） CR 22 BR CR 22 B CR 22 BUUR CR 22 BUU 157 34.925（1 3╱8） 19.050（ 3╱4） 12.700（ 1╱2） 1╱2 - 20  15.875（ 5╱8） 20.4（0.80） 31.750（1 1╱4） 7.938（ 5╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 6.350（ 1╱4） 1.588（ 1╱16） 21.828（ 55╱64） 27.7 14 200 16 000 I
15.875 CR 24 BR CR 24 B CR 24 BUUR CR 24 BUU 225 38.100（1 1╱2） 22.225（ 7╱8） 15.875（ 5╱8） 5╱8 - 18 19.050（ 3╱4） 23.6（0.93） 38.100（1 1╱2） 9.525（ 3╱8） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 7.938（ 5╱16） 1.588（ 1╱16） 26.196（1 3╱64） 55.7 18 600 24 300
（ 5╱8） CR 26 BR CR 26 B CR 26 BUUR CR 26 BUU 260 41.275（1 5╱8） 22.225（ 7╱8） 15.875（ 5╱8） 5╱8 - 18 19.050（ 3╱4） 23.6（0.93） 38.100（1 1╱2） 9.525（ 3╱8） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 7.938（ 5╱16） 1.588（ 1╱16） 26.196（1 3╱64） 55.7 18 600 24 300
19.050 CR 28 BR CR 28 B CR 28 BUUR CR 28 BUU 365 44.450（1 3╱4） 25.400（1 ） 19.050（ 3╱4） 3╱4 - 16 22.225（ 7╱8） 26.8（1.06） 44.450（1 3╱4） 11.112（ 7╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 7.938（ 5╱16） 1.588（ 1╱16） 32.543（1 9╱32） 100 25 100 38 200
（ 3╱4） CR 30 BR CR 30 B CR 30 BUUR CR 30 BUU 410 47.625（1 7╱8） 25.400（1 ） 19.050（ 3╱4） 3╱4 - 16 22.225（ 7╱8） 26.8（1.06） 44.450（1 3╱4） 11.112（ 7╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 7.938（ 5╱16） 1.588（ 1╱16） 32.543（1 9╱32） 100 25 100 38 200
22.225 CR 32 BR CR 32 B CR 32 BUUR CR 32 BUU 615 50.800（2 ） 31.750（1 1╱4） 22.225（ 7╱8） 7╱8 - 14 25.400（1 ） 33.5（1.32） 50.800（2 ） 12.700（ 1╱2） 0.794（ 1╱32） 4.762（ 3╱16） 4.762（ 3╱16）11.112（ 7╱16） 1.588（ 1╱16） 37.306（1 15╱32） 162 32 500 63 900
（ 7╱8） CR 36 BR CR 36 B CR 36 BUUR CR 36 BUU 750 57.150（2 1╱4） 31.750（1 1╱4） 22.225（ 7╱8） 7╱8 - 14 25.400（1 ） 33.5（1.32） 50.800（2 ） 12.700（ 1╱2） 0.794（ 1╱32） 4.762（ 3╱16） 4.762（ 3╱16）11.112（ 7╱16） 1.588（ 1╱16） 37.306（1 15╱32） 162 32 500 63 900

Remarks1.   Models with a stud diameter d1 of 6.35 mm or less have no oil hole. Other models are provided with one oil hole each on the
outside surface and end surface of the stud.
2.   Provided with prepacked grease.
3.   For the maximum allowable static load, please contact .

1N=0.102kgf=0.2248lbs.
I61 1mm=0.03937inch
I62
 CAM FOLLOWERS
Inch Series Cam Followers With Cage/With Screwdriver Slot
C

B3 r
r
g2

f
g1
g1
D

G
d1
G1

R=500 C1 R=500

B B2

Stud dia. 4.826 − 22.225mm CR … R CR CR … UUR CR … UU

Identification number Mass Boundary dimensions　mm(inch) Mounting Maximum Basic dynamic Basic static
Stud (Ref.) dimension tightening load rating load rating
dia. Shield type Sealed type f torque
C C0
mm Min.
With crowned With cylindrical With crowned With cylindrical
g D C d1 G G1 B B2 B3 C1 g1 g2 r
(inch) outer ring outer ring outer ring outer ring UNF max mm(inch) N-m N N

CR 8 R CR   8 CR 8 UUR CR 8 UU 9 12.700（ 1╱2） 8.731（ 11╱32）4.826 No.10-32 6.350（ 1╱4） 10.2（0.40） 12.700（ 1╱2） （ 1╱32）
 ─   （   ─  ） 0.794 （ 1╱8）
*3.175    ─   （   ─  ）0.397（ 1╱64） 8.334 （ 21╱64） 1.4 2 520 2 140
4.826
CR 8-1 R CR   8-1 CR 8-1 UUR CR 8-1 UU 10 12.700（ 1╱2） 9.525（ 3╱8） 4.826 No.10-32 6.350（ 1╱4） 10.9（0.43） （ 5╱8）
15.875    ─   （   ─  ） 0.794（ 1╱32） *3.175（ 1╱8）   ─   （   ─  ）0.397（ 1╱64） 8.334（ 21╱64） 1.4 2 520 2 140
6.350 CR 10 R CR 10 CR 10 UUR CR 10 UU 19 15.875（ 5╱8） 10.319（ 13╱32） 6.350（ 1╱4） 1╱4 - 28 7.938（ 5╱16） 11.8（0.46） 15.875（ 5╱8）    ─   （   ─  ） 0.794（ 1╱32） *3.175（ 1╱8）   ─   （   ─  ）0.397（ 1╱64） 11.509（ 29╱64） 3.4 3 650 3 670
（ 1╱4） CR 10-1 R CR 10-1 CR 10-1 UUR CR 10-1 UU 21 15.875（ 5╱8） 11.112（ 7╱16） 6.350（ 1╱4） 1╱4 - 28 7.938（ 5╱16） 12.5（0.49） 19.050（ 3╱4）    ─   （   ─  ） 0.794（ 1╱32） *3.175（ 1╱8）   ─   （   ─  ）0.397（ 1╱64） 11.509（ 29╱64） 3.4 3 650 3 670
9.525 CR 12 R CR 12 CR 12 UUR CR 12 UU 35 19.050（ 3╱4） 12.700（ 1╱2） 9.525（ 3╱8） 3╱8 - 24 9.525（ 3╱8） 14.2（0.56） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16）2.381（ 3╱32）0.794（ 1╱32） 13.494（ 17╱32） 10.8 4 420 5 110
（ 3╱8） CR 14 R CR 14 CR 14 UUR CR 14 UU 46 22.225（ 7╱8） 12.700（ 1╱2） 9.525（ 3╱8） 3╱8 - 24 9.525（ 3╱8） 14.2（0.56） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16）2.381（ 3╱32）0.794（ 1╱32） 15.081（ 19╱32） 10.8 4 790 5 810
11.112 CR 16 R CR 16 CR 16 UUR CR 16 UU 73 25.400（1 ） 15.875（ 5╱8） 11.112（ 7╱16） 7╱16 - 20 12.700（ 1╱2） 17.3（0.68） 25.400（1 ） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16）3.175（ 1╱8）1.191（ 3╱64） 17.859（ 45╱64） 17.4 8 810 10 800
（ 7╱16） CR 18 R CR 18 CR 18 UUR CR 18 UU 99 28.575（1 1╱8） 15.875（ 5╱8） 11.112（ 7╱16） 7╱16 - 20 12.700（ 1╱2） 17.3（0.68） 25.400（1 ） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16）3.175（ 1╱8）1.588（ 1╱16）19.050（ 3╱4） 17.4 9 180 11 600
12.700 CR 20 R CR 20 CR 20 UUR CR 20 UU 132 31.750（1 1╱4） 19.050（ 3╱4） 12.700（ 1╱2） 1╱2 - 20 15.875（ 5╱8） 20.4（0.80） 31.750（1 1╱4） 7.938（ 5╱16） 0.794（ 1╱32） 4.762（ 3╱16）3.175（ 1╱8）1.588（ 1╱16） 21.828（ 55╱64） 27.7 14 200 16 000
（ 1╱2） CR 22 R CR 22 CR 22 UUR CR 22 UU 157 34.925（1 3╱8） 19.050（ 3╱4） 12.700（ 1╱2） 1╱2 - 20  15.875（ 5╱8） 20.4（0.80） 31.750（1 1╱4） 7.938（ 5╱16） 0.794（ 1╱32） 4.762（ 3╱16）3.175（ 1╱8）1.588（ 1╱16） 21.828（ 55╱64） 27.7 14 200 16 000 I
15.875 CR 24 R CR 24 CR 24 UUR CR 24 UU 225 38.100（1 1╱2） 22.225（ 7╱8） 15.875（ 5╱8） 5╱8 - 18 19.050（ 3╱4） 23.6（0.93） 38.100（1 1╱2） 9.525（ 3╱8） 0.794（ 1╱32） 4.762（ 3╱16）3.969（ 5╱32）1.588（ 1╱16）26.196（1 3╱64） 55.7 18 600 24 300
（ 5╱8） CR 26 R CR 26 CR 26 UUR CR 26 UU 260 41.275（1 5╱8） 22.225（ 7╱8） 15.875（ 5╱8） 5╱8 - 18 19.050（ 3╱4） 23.6（0.93） 38.100（1 1╱2） 9.525（ 3╱8） 0.794（ 1╱32） 4.762（ 3╱16）3.969（ 5╱32）1.588（ 1╱16）26.196（1 3╱64） 55.7 18 600 24 300
19.050 CR 28 R CR 28 CR 28 UUR CR 28 UU 365 44.450（1 3╱4） 25.400（1 ） 19.050（ 3╱4） 3╱4 - 16 22.225（ 7╱8） 26.8（1.06） 44.450（1 3╱4） 11.112（ 7╱16） 0.794（ 1╱32） 4.762（ 3╱16）3.969（ 5╱32）1.588（ 1╱16）32.543（1 9╱32） 100 25 100 38 200
（ 3╱4） CR 30 R CR 30 CR 30 UUR CR 30 UU 410 47.625（1 7╱8） 25.400（1 ） 19.050（ 3╱4） 3╱4 - 16 22.225（ 7╱8） 26.8（1.06） 44.450（1 3╱4） 11.112（ 7╱16） 0.794（ 1╱32） 4.762（ 3╱16）3.969（ 5╱32）1.588（ 1╱16）32.543（1 9╱32） 100 25 100 38 200
22.225 CR 32 R CR 32 CR 32 UUR CR 32 UU 615 50.800（2 ） 31.750（1 1╱4） 22.225（ 7╱8） 7╱8 - 14 25.400（1 ） 33.5（1.32） 50.800（2 ） 12.700（ 1╱2） 0.794（ 1╱32） 4.762（ 3╱16）4.762（ 3╱16）1.588（ 1╱16）37.306（1 15╱32） 162 32 500 63 900
（ 7╱8） CR 36 R CR 36 CR 36 UUR CR 36 UU 750 57.150（2 1╱4） 31.750（1 1╱4） 22.225（ 7╱8） 7╱8 - 14 25.400（1 ） 33.5（1.32） 50.800（2 ） 12.700（ 1╱2） 0.794（ 1╱32） 4.762（ 3╱16）4.762（ 3╱16）1.588（ 1╱16）37.306（1 15╱32） 162 32 500 63 900

Remarks1.   Models with a stud diameter d1 of 6.35 mm or less (marked *) are provided with an oil hole on the stud head only. Other models
are provided with one oil hole each on the head, outside surface and end surface of the stud.
2.   Provided with prepacked grease.
3.   For the maximum allowable static load, please contact .

1N=0.102kgf=0.2248lbs.
I63 1mm=0.03937inch
I64
 CAM FOLLOWERS
Inch Series Cam Followers Full Complement Type/With Hexagon Hole

B3 r r

g2

f
g1
D

G
H

d1
G1

R=500 C1 R=500

B B2

Stud dia. 4.826 − 22.225mm CR … VBR CR … VB CR … VBUUR CR … VBUU

Identification number Mass Boundary dimensions　mm(inch) Mounting Maximum Basic dynamic Basic static
Stud (Ref.) dimension tightening load rating load rating
dia. Shield type Sealed type f torque
C C0
mm Min.
With crowned With cylindrical With crowned With cylindrical
g D C d1 G G1 B B2 B3 C1 g1 g2 H r
(inch) outer ring outer ring outer ring outer ring UNF max mm(inch) N-m N N

CR 8 VBR CR   8   VB CR 8 VBUUR CR 8 VBUU 9 12.700（ 1╱2） 8.731（ 11╱32）

4.826 No.10-32 6.350（ 1╱4） 10.2（0.40） 12.700（ 1╱2） （ 1╱32）
 ─   （   ─  ） 0.794  ─   （   ─  ）  ─   （   ─  ） 3.175（ 1╱8） 0.397（ 1╱64） （ 21╱64） 1.4
8.334 4 260 4 750
4.826
CR 8-1 VBR CR   8-1VB CR 8-1 VBUUR CR 8-1 VBUU 10 12.700（ 1╱2） 9.525（ 3╱8） 4.826 No.10-32 6.350（ 1╱4） 10.9（0.43） （ 5╱8）
15.875    ─   （   ─  ） 0.794（ ）    ─   （   ─  ）    ─   （   ─  ） 3.175（ 1╱8） 0.397（ 1╱64）
╱
1 32 8.334（ 21╱64） 1.4 4 710 5 410
6.350 CR 10 VBR CR 10   VB CR 10 VBUUR CR 10 VBUU 19 15.875（ 5╱8） 10.319（ 13╱32） 6.350（ 1╱4） 1╱4 - 28 7.938（ 5╱16） 11.8（0.46） 15.875（ 5╱8）    ─   （   ─  ） 0.794（ 1╱32）    ─   （   ─  ）    ─   （   ─  ） 3.175（ 1╱8） 0.397（ 1╱64） 11.509（ 29╱64） 3.4 5 830 7 660
（ 1╱4） CR 10-1 VBR CR 10-1VB CR 10-1 VBUUR CR 10-1 VBUU 21 15.875（ 5╱8） 11.112（ 7╱16） 6.350（ 1╱4） 1╱4 - 28 7.938（ 5╱16） 12.5（0.49） 19.050（ 3╱4）    ─   （   ─  ） 0.794（ 1╱32）    ─   （   ─  ）    ─   （   ─  ） 3.175（ 1╱8） 0.397（ 1╱64） 11.509（ 29╱64） 3.4 6 340 8 530
9.525 CR 12 VBR CR 12   VB CR 12 VBUUR CR 12 VBUU 36 19.050（ 3╱4） 12.700（ 1╱2） 9.525（ 3╱8） 3╱8 - 24 9.525（ 3╱8） 14.2（0.56） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 4.762（ 3╱16） 0.794（ 1╱32） 13.494（ 17╱32） 10.8 8 710 12 300
（ 3╱8） CR 14 VBR CR 14   VB CR 14 VBUUR CR 14 VBUU 47 22.225（ 7╱8） 12.700（ 1╱2） 9.525（ 3╱8） 3╱8 - 24 9.525（ 3╱8） 14.2（0.56） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 4.762（ 3╱16） 0.794（ 1╱32） 15.081（ 19╱32） 10.8 8 710 12 300
11.112 CR 16 VBR CR 16   VB CR 16 VBUUR CR 16 VBUU 74 25.400（1 ） 15.875（ 5╱8） 11.112（ 7╱16） 7╱16 - 20 12.700（ 1╱2） 17.3（0.68） 25.400（1 ） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 6.350（ 1╱4） 1.191（ 3╱64） 17.859（ 45╱64） 17.4 13 100 22 700
（ 7╱16） CR 18 VBR CR 18   VB CR 18 VBUUR CR 18 VBUU 101 28.575（1 1╱8） 15.875（ 5╱8） 11.112（ 7╱16） 7╱16 - 20 12.700（ 1╱2） 17.3（0.68） 25.400（1 ） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 6.350（ 1╱4） 1.588（ 1╱16） 19.050（ 3╱4） 17.4 13 100 22 700
12.700 CR 20 VBR CR 20   VB CR 20 VBUUR CR 20 VBUU 137 31.750（1 1╱4） 19.050（ 3╱4） 12.700（ 1╱2） 1╱2 - 20 15.875（ 5╱8） 20.4（0.80） 31.750（1 1╱4） 7.938（ 5╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 6.350（ 1╱4） 1.588（ 1╱16） 21.828（ 55╱64） 27.7 23 600 31 700
（ 1╱2） CR 22 VBR CR 22   VB CR 22 VBUUR CR 22 VBUU 160 34.925（1 3╱8） 19.050（ 3╱4） 12.700（ 1╱2） 1╱2 - 20  15.875（ 5╱8） 20.4（0.80） 31.750（1 1╱4） 7.938（ 5╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 6.350（ 1╱4） 1.588（ 1╱16） 21.828（ 55╱64） 27.7 23 600 31 700 I
15.875 CR 24 VBR CR 24   VB CR 24 VBUUR CR 24 VBUU 230 38.100（1 1╱2） 22.225（ 7╱8） 15.875（ 5╱8） 5╱8 - 18 19.050（ 3╱4） 23.6（0.93） 38.100（1 1╱2） 9.525（ 3╱8） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 7.938（ 5╱16） 1.588（ 1╱16） 26.196（1 3╱64） 55.7 28 200 40 100
（ 5╱8） CR 26 VBR CR 26   VB CR 26 VBUUR CR 26 VBUU 265 41.275（1 5╱8） 22.225（ 7╱8） 15.875（ 5╱8） 5╱8 - 18 19.050（ 3╱4） 23.6（0.93） 38.100（1 1╱2） 9.525（ 3╱8） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 7.938（ 5╱16） 1.588（ 1╱16） 26.196（1 3╱64） 55.7 28 200 40 100
19.050 CR 28 VBR CR 28   VB CR 28 VBUUR CR 28 VBUU 372 44.450（1 3╱4） 25.400（1 ） 19.050（ 3╱4） 3╱4 - 16 22.225（ 7╱8） 26.8（1.06） 44.450（1 3╱4） 11.112（ 7╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 7.938（ 5╱16） 1.588（ 1╱16） 32.543（1 9╱32） 100 35 300 55 600
（ 3╱4） CR 30 VBR CR 30   VB CR 30 VBUUR CR 30 VBUU 418 47.625（1 7╱8） 25.400（1 ） 19.050（ 3╱4） 3╱4 - 16 22.225（ 7╱8） 26.8（1.06） 44.450（1 3╱4） 11.112（ 7╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 7.938（ 5╱16） 1.588（ 1╱16） 32.543（1 9╱32） 100 35 300 55 600
22.225 CR 32 VBR CR 32   VB CR 32 VBUUR CR 32 VBUU 627 50.800（2 ） 31.750（1 1╱4） 22.225（ 7╱8） 7╱8 - 14 25.400（1 ） 33.5（1.32） 50.800（2 ） 12.700（ 1╱2） 0.794（ 1╱32） 4.762（ 3╱16） 4.762（ 3╱16）11.112（ 7╱16） 1.588（ 1╱16） 37.306（1 15╱32） 162 45 700 80 600
（ 7╱8） CR 36 VBR CR 36   VB CR 36 VBUUR CR 36 VBUU 759 57.150（2 1╱4） 31.750（1 1╱4） 22.225（ 7╱8） 7╱8 - 14 25.400（1 ） 33.5（1.32） 50.800（2 ） 12.700（ 1╱2） 0.794（ 1╱32） 4.762（ 3╱16） 4.762（ 3╱16）11.112（ 7╱16） 1.588（ 1╱16） 37.306（1 15╱32） 162 45 700 80 600

Remarks1.   Models with a stud diameter d1 of 6.35 mm or less have no oil hole. Other models are provided with one oil hole each on the
outside surface and end surface of the stud.
2.   Provided with prepacked grease.
3.   For the maximum allowable static load, please contact .

1N=0.102kgf=0.2248lbs.
I65 1mm=0.03937inch
I66
 CAM FOLLOWERS
Inch Series Cam Followers Full Complement Type/With Screwdriver Slot

C
r r
B3

r
r
g2

f
g1
g1
D

G
d1
G1
R=500
R=500 C1

B B2

Stud dia. 4.826 − 31.750mm CR … VR CR … V CR … VUUR CR … VUU

Identification number Mass Boundary dimensions　mm(inch) Mounting Maximum Basic dynamic Basic static
Stud (Ref.) dimension tightening load rating load rating
dia. Shield type Sealed type f torque
C C0
mm Min.
With crowned With cylindrical With crowned With cylindrical
g D C d1 G G1 B B2 B3 C1 g1 g2 r
(inch) outer ring outer ring outer ring outer ring UNF max mm(inch) N-m N N

CR 8 VR CR   8    V CR 8 VUUR CR 8 VUU 9 12.700（ 1╱2） 8.731（ 11╱32）

4.826 No.10-32 6.350（ 1╱4） 10.2（0.40） 12.700（ 1╱2） （ 1╱32）
 ─   （   ─  ） 0.794 （ 1╱8）
*3.175 （ 1╱64）
  ─   （   ─  ） 0.397 （ 21╱64） 1.4
8.334 4 260 4 750
4.826
CR 8-1 VR CR   8-1 V CR 8-1 VUUR CR 8-1 VUU 10 12.700（ 1╱2） 9.525（ 3╱8） 4.826 No.10-32 6.350（ 1╱4） 10.9（0.43） （ 5╱8）
15.875    ─   （   ─  ） 0.794（ 1╱32） *3.175（ 1╱8）    ─   （   ─  ） 0.397（ 1╱64） 8.334（ 21╱64） 1.4 4 710 5 410
6.350 CR 10 VR CR 10    V CR 10 VUUR CR 10 VUU 19 15.875（ 5╱8） 10.319（ 13╱32） 6.350（ 1╱4） 1╱4 - 28 7.938（ 5╱16） 11.8（0.46） 15.875（ 5╱8）    ─   （   ─  ） 0.794（ 1╱32） *3.175（ 1╱8）    ─   （   ─  ） 0.397（ 1╱64） 11.509（ 29╱64） 3.4 5 830 7 660
（ 1╱4） CR 10-1 VR CR 10-1 V CR 10-1 VUUR CR 10-1 VUU 21 15.875（ 5╱8） 11.112（ 7╱16） 6.350（ 1╱4） 1╱4 - 28 7.938（ 5╱16） 12.5（0.49） 19.050（ 3╱4）    ─   （   ─  ） 0.794（ 1╱32） *3.175（ 1╱8）    ─   （   ─  ） 0.397（ 1╱64） 11.509（ 29╱64） 3.4 6 340 8 530
9.525 CR 12 VR CR 12    V CR 12 VUUR CR 12 VUU 36 19.050（ 3╱4） 12.700（ 1╱2） 9.525（ 3╱8） 3╱8 - 24 9.525（ 3╱8） 14.2（0.56） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 0.794（ 1╱32） 13.494（ 17╱32） 10.8 8 710 12 300
（ 3╱8） CR 14 VR CR 14    V CR 14 VUUR CR 14 VUU 47 22.225（ 7╱8） 12.700（ 1╱2） 9.525（ 3╱8） 3╱8 - 24 9.525（ 3╱8） 14.2（0.56） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 0.794（ 1╱32） 15.081（ 19╱32） 10.8 8 710 12 300
11.112 CR 16 VR CR 16    V CR 16 VUUR CR 16 VUU 74 25.400（1 ） 15.875（ 5╱8） 11.112（ 7╱16） 7╱16 - 20 12.700（ 1╱2） 17.3（0.68） 25.400（1 ） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 1.191（ 3╱64） 17.859（ 45╱64） 17.4 13 100 22 700
（ 7╱16） CR 18 VR CR 18    V CR 18 VUUR CR 18 VUU 101 28.575（1 1╱8） 15.875（ 5╱8） 11.112（ 7╱16） 7╱16 - 20 12.700（ 1╱2） 17.3（0.68） 25.400（1 ） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 1.588（ 1╱16） 19.050（ 3╱4） 17.4 13 100 22 700
12.700 CR 20 VR CR 20    V CR 20 VUUR CR 20 VUU 137 31.750（1 1╱4） 19.050（ 3╱4） 12.700（ 1╱2） 1╱2 - 20 15.875（ 5╱8） 20.4（0.80） 31.750（1 1╱4） 7.938（ 5╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 1.588（ 1╱16） 21.828（ 55╱64） 27.7 23 600 31 700
（ 1╱2） CR 22 VR CR 22    V CR 22 VUUR CR 22 VUU 160 34.925（1 3╱8） 19.050（ 3╱4） 12.700（ 1╱2） 1╱2 - 20  15.875（ 5╱8） 20.4（0.80） 31.750（1 1╱4） 7.938（ 5╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.175（ 1╱8） 1.588（ 1╱16） 21.828（ 55╱64） 27.7 23 600 31 700 I
15.875 CR 24 VR CR 24    V CR 24 VUUR CR 24 VUU 230 38.100（1 1╱2） 22.225（ 7╱8） 15.875（ 5╱8） 5╱8 - 18 19.050（ 3╱4） 23.6（0.93） 38.100（1 1╱2） 9.525（ 3╱8） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 1.588（ 1╱16） 26.196（1 3╱64） 55.7 28 200 40 100
（ 5╱8） CR 26 VR CR 26    V CR 26 VUUR CR 26 VUU 265 41.275（1 5╱8） 22.225（ 7╱8） 15.875（ 5╱8） 5╱8 - 18 19.050（ 3╱4） 23.6（0.93） 38.100（1 1╱2） 9.525（ 3╱8） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 1.588（ 1╱16） 26.196（1 3╱64） 55.7 28 200 40 100
19.050 CR 28 VR CR 28    V CR 28 VUUR CR 28 VUU 372 44.450（1 3╱4） 25.400（1 ） 19.050（ 3╱4） 3╱4 - 16 22.225（ 7╱8） 26.8（1.06） 44.450（1 3╱4） 11.112（ 7╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 1.588（ 1╱16） 32.543（1 9╱32） 100 35 300 55 600
（ 3╱4） CR 30 VR CR 30    V CR 30 VUUR CR 30 VUU 418 47.625（1 7╱8） 25.400（1 ） 19.050（ 3╱4） 3╱4 - 16 22.225（ 7╱8） 26.8（1.06） 44.450（1 3╱4） 11.112（ 7╱16） 0.794（ 1╱32） 4.762（ 3╱16） 3.969（ 5╱32） 1.588（ 1╱16） 32.543（1 9╱32） 100 35 300 55 600
22.225 CR 32 VR CR 32    V CR 32 VUUR CR 32 VUU 627 50.800（2 ） 31.750（1 1╱4） 22.225（ 7╱8） 7╱8 - 14 25.400（1 ） 33.5（1.32） 50.800（2 ） 12.700（ 1╱2） 0.794（ 1╱32） 4.762（ 3╱16） 4.762（ 3╱16） 1.588（ 1╱16） 37.306（1 15╱32） 162 45 700 80 600
（ 7╱8） CR 36 VR CR 36    V CR 36 VUUR CR 36 VUU 759 57.150（2 1╱4） 31.750（1 1╱4） 22.225（ 7╱8） 7╱8 - 14 25.400（1 ） 33.5（1.32） 50.800（2 ） 12.700（ 1╱2） 0.794（ 1╱32） 4.762（ 3╱16） 4.762（ 3╱16） 1.588（ 1╱16） 37.306（1 15╱32） 162 45 700 80 600
31.750
─ ─ ─ CR 48 VUU 1 960 76.200（3 ） 44.450（1 3╱4）31.750（1 1╱4） 1 1╱4 - 12 31.750（1 1╱4） 46.4（1.83） 63.500（2 1╱2） 15.875（ 5╱8）1.588（ 1╱16） 6.350（ 1╱4）     4.762（ 3╱16） 2.381（ 3╱32） 51.991（2 3╱64） 500 77 600 172 000
（1 1╱4）

Remarks1.   Models with a stud diameter d1 of 6.35 mm or less (marked *) are provided with an oil hole on the stud head only. Other models
are provided with one oil hole each on the head, outside surface and end surface of the stud.
2.   Provided with prepacked grease.
3.   For the maximum allowable static load, please contact .

1N=0.102kgf=0.2248lbs.
I67 1mm=0.03937inch
I68
 CAM FOLLOWERS
Inch Series Heavy Duty Cam Followers Full Complement Type/With Hexagon Hole

B3

g2

f
f
D

G
g1
H

d1
G1

R C1 R R

B B2

Stud dia. 6.350−50.800mm CRH … VBR CRH … VBUUR

Identification number Mass Boundary dimensions　mm(inch) Mounting Maximum Basic dynamic Basic static
Stud (Ref.) dimension tightening load rating load rating
dia. Shield type Sealed type f torque
C C0
mm With crowned With crowned g D C d1 G G1 B B2 B3 C1 g1 g2 H R Min.
(inch) outer ring outer ring UNF max mm(inch) N-m N N
6.350 CRH 8-1 VBR CRH 8-1 VBUUR 12 12.700（ 1╱2） 9.525（ 3╱8） 6.350（ 1╱4） 1╱4 - 28 6.350（ 1╱4） 11.1（0.44） 15.875（ 5╱8） （ 1╱32）
    ─   （   ─  ） 0.794     ─   （   ─  ）     ─   （   ─  ） 3.175（ 1╱8） 180（   7） 8.334（ 21╱64） 3.4 4 710 5 410
（ 1╱4） CRH 9 VBR CRH 9 VBUUR 15 14.288（ 9╱16）
9.525（ 3╱8）
6.350（ 1╱4）
1╱4 - 28 6.350（ 1╱4） 11.1（0.44）
（ 5╱8）
15.875     ─   （   ─  ） 0.794（ ╱32）     ─   （   ─  ）     ─   （   ─  ） 3.175（ 1╱8）
1 180（   7） 8.334（ 21╱64） 3.4 4 710 5 410
7.938 CRH 10-1 VBR CRH 10-1 VBUUR 23 15.875（ 5╱8） 11.112（ 7╱16） 7.938（ 5╱16） 5╱16
 - 24 7.938（ 5╱16） 12.8（0.50） 19.050（ 3╱4）     ─   （   ─  ） 0.794（ 1╱32）     ─   （   ─  ）     ─   （   ─  ） 3.175（ 1╱8） 200（   8） 11.112（ 7╱16） 6.8 6 340 8 530
（ 5╱16） CRH 11 VBR CRH 11 VBUUR 27 17.462（ 11╱16） 11.112（ 7╱16） 7.938（ 5╱16） 5╱16
 - 24 7.938（ 5╱16） 12.8（0.50） 19.050（ 3╱4）     ─   （   ─  ） 0.794（ 1╱32）     ─   （   ─  ）        ─   （   ─  ） 3.175
    （ 1╱8） 200（   8） 11.112（ 7╱16） 6.8 6 340 8 530
11.112 CRH 12 VBR CRH 12 VBUUR 39 19.050（ 3╱4） 12.700（ 1╱2） 11.112（ 7╱16） 7╱16
 - 20 9.525（ 3╱8） 14.6（0.57） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 4.762（ 3╱16） 250（10） 13.494（ 17╱32） 17.6 8 710 12 300
（ 7╱16） CRH 14 VBR CRH 14 VBUUR 49 22.225（ 7╱8） 12.700（ 1╱2） 11.112（ 7╱16） 7╱16
 - 20 9.525（ 3╱8） 14.6（0.57） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 4.762（ 3╱16） 250（10） 13.494（ 17╱32） 17.6 8 710 12 300
15.875 CRH 16 VBR CRH 16 VBUUR 93 25.400（1 ） 15.875（ 5╱8） 15.875（ 5╱8） 5╱8 - 18 12.700（ 1╱2） 17.9（0.70） 25.400（1 ） 6.350（ 1╱4） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 6.350（ 1╱4） 300（12） 18.256（ 23╱32） 57.8 13 100 22 700
（ 5╱8） CRH 18 VBR CRH 18 VBUUR 109 28.575（1 1╱8） 15.875（ 5╱8） 15.875（ 5╱8） 5╱8 - 18 12.700（ 1╱2） 17.9（0.70） 25.400（1 ） 6.350（ 1╱4） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 6.350（ 1╱4） 300（12） 18.256（ 23╱32） 57.8 13 100 22 700
19.050 CRH 20 VBR CRH 20 VBUUR 176 31.750（1 1╱4） 19.050（ 3╱4） 19.050（ 3╱4） 3╱4 - 16 15.875（ 5╱8） 21.0（0.83） 31.750（1 1╱4） 7.938（ 5╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 6.350（ 1╱4） 360（14） 24.209（ 61╱64） 103 23 600 31 700
（ 3╱4） CRH 22 VBR CRH 22 VBUUR 200 34.925（1 3╱8） 19.050（ 3╱4） 19.050（ 3╱4） 3╱4 - 16 15.875（ 5╱8） 21.0（0.83） 31.750（1 1╱4） 7.938（ 5╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 6.350（ 1╱4） 360（14） 24.209（ 61╱64） 103 23 600 31 700 I
22.225 CRH 24 VBR CRH 24 VBUUR 296 38.100（1 1╱2） 22.225（ 7╱8） 22.225（ 7╱8） 7╱8 - 14 19.050（ 3╱4） 24.3（0.96） 38.100（1 1╱2） 9.525（ 3╱8） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 7.938（ 5╱16） 500（20） 26.988（1 1╱16） 162 28 200 40 100
（ 7╱8） CRH 26 VBR CRH 26 VBUUR 329 41.275（1 5╱8） 22.225（ 7╱8） 22.225（ 7╱8） 7╱8 - 14 19.050（ 3╱4） 24.3（0.96) 38.100（1 1╱2） 9.525（ 3╱8） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 7.938（ 5╱16） 500（20） 26.988（1 1╱16） 162 28 200 40 100
25.400 CRH 28 VBR CRH 28 VBUUR 463 44.450（1 3╱4） 25.400（1 ） 25.400（1 ） 1- 14 UNS 22.225（ 7╱8） 27.4（1.08） 44.450（1 3╱4） 11.112（ 7╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 7.938（ 5╱16） 500（20） 32.941（1 19╱64） 258 35 300 55 600
（ 1 ） CRH 30 VBR CRH 30 VBUUR 508 47.625（1 7╱8） 25.400（1 ） 25.400（1 ） 1- 14 UNS 22.225（ 7╱8） 27.4（1.08） 44.450（1 3╱4） 11.112（ 7╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 7.938（ 5╱16） 500（20） 32.941（1 19╱64） 258 35 300 55 600
28.575 CRH 32 VBR CRH 32 VBUUR 722 50.800（2 ） 31.750（1 1╱4） 28.575（1 1╱8） 1 1╱8 - 12 25.400（1 ） 34.2（1.35） 50.800（2 ） 12.700（ 1╱2） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 11.112（ 7╱16） 600（24） 37.306（1 15╱32） 356 45 700 80 600
（1 1╱8） CRH 36 VBR CRH 36 VBUUR 858 57.150（2 1╱4） 31.750（1 1╱4） 28.575（1 1╱8） 1 1╱8 - 12 25.400（1 ） 34.2（1.35） 50.800（2 ） 12.700（ 1╱2） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 11.112（ 7╱16） 600（24） 37.306（1 15╱32） 356 45 700 80 600
31.750 CRH 40 VBR CRH 40 VBUUR 1 260 63.500（2 1╱2） 38.100（1 1╱2） 31.750（1 1╱4） 1 1╱4 - 12 28.575（1 1╱8） 40.0（1.57） 57.150（2 1╱4） 14.288（ 9╱16） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 12.700（ 1╱2） 760（30） 40.878（1 39╱64） 500 61 400 116 000
（1 1╱4） CRH 44 VBR CRH 44 VBUUR 1 460 69.850（2 3╱4） 38.100（1 1╱2） 31.750（1 1╱4） 1 1╱4 - 12 28.575（1 1╱8） 40.0（1.57） 57.150（2 1╱4） 14.288（ 9╱16） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 12.700（ 1╱2） 760（30） 40.878（1 39╱64） 500 61 400 116 000
38.100 CRH 48 VBR CRH 48 VBUUR 2 100 76.200（3 ） 44.450（1 3╱4） 38.100（1 1╱2） 1 1╱2 - 12 31.750（1 1╱4） 46.4（1.83） 63.500（2 1╱2） 15.875（ 5╱8） 1.588（ 1╱16） 6.350（ 1╱4） 3.175（ 1╱8） 19.050（ 3╱4） 760（30） 51.991（2 3╱64） 892 77 600 172 000
（1 1╱2） CRH 52 VBR CRH 52 VBUUR 2 380 82.550（3 1╱4） 44.450（1 3╱4） 38.100（1 1╱2） 1 1╱2 - 12 31.750（1 1╱4） 46.4（1.83） 63.500（2 1╱2） 15.875（ 5╱8） 1.588（ 1╱16） 6.350（ 1╱4） 3.175（ 1╱8） 19.050（ 3╱4） 760（30） 51.991（2 3╱64） 892 77 600 172 000
44.450
CRH 56 VBR CRH 56 VBUUR 3 240 88.900（3 1╱2） 50.800（2 ） 44.450（1 3╱4） 1 3╱4 - 12UN 34.925（1 3╱8） 52.8（2.08） 69.850（2 3╱4） 17.462（ 11╱16） 1.588（ 1╱16） 6.350（ 1╱4） 3.175（ 1╱8） 19.050（ 3╱4） 760（30） 59.928（2 23╱64） 1450 111 000 239 000
（1 3╱4）
50.800
4 960 101.600（4 ） 57.150（2 1╱4） 50.800（2 ） 2- 12 UN 38.100（1 1╱2） 59.4（2.34） 88.900（3 1╱2） 19.050（ 3╱4） 1.588（ 1╱16） 6.350（ 1╱4） 3.175（ 1╱8） 19.050（ 3╱4） 760（30） 64.691（2 35╱64） 2190
（ 2 ） CRH 64 VBR CRH 64 VBUUR
142 000 317 000

Remarks1.   Models with a stud diameter d1 of 7.938 mm or less have no oil hole. Other models are provided with one oil hole each on the
outside surface and end surface of the stud.
2.   Provided with prepacked grease.
3.   For the maximum allowable static load, please contact .

1N=0.102kgf=0.2248lbs.
I69 1mm=0.03937inch
I70
 CAM FOLLOWERS
Inch Series Heavy Duty Cam Followers Full Complement Type/With Hexagon Hole

r B3 r
g2

f
g1

G
D
H

d1
G1
C1

B B2

Stud dia. 6.350 − 50.800mm CRH … VB CRH … VBUU

Identification number Mass Boundary dimensions　mm(inch) Mounting Maximum Basic dynamic Basic static
Stud (Ref.) dimension tightening load rating load rating
dia. f torque
C C0
Shield type Sealed type
mm Min.
With cylindrical With cylindrical g D C d1 G G1 B B2 B3 C1 g1 g2 H r
(inch) outer ring outer ring UNF max mm(inch) N-m N N
6.350 CRH 8-1 VB CRH 8-1 VBUU 12 12.700（ 1╱2） 9.525（ 3╱8） 6.350（ 1╱4） 1╱4
 - 28 6.350（ 1╱4） 11.1（0.44） 15.875（ 5╱8） （ 1╱32）
    ─   （   ─  ） 0.794     ─   （   ─  ）     ─   （   ─  ） 3.175（ 1╱8）0.397（ 1╱64） 8.334（ 21╱64） 3.4 4 710 5 410
（ 1╱4） CRH 9 VB CRH 9 VBUU 15 14.288（ 9╱16）
9.525（ 3╱8）
6.350（ 1╱4）
1╱4 - 28 6.350（ 1╱4） 11.1（0.44）
（ 5╱8）
15.875     ─   （   ─  ） 0.794（ ）    ─   （   ─  ）     ─   （   ─  ） 3.175（ 1╱8）0.397（ 1╱64）
╱
1 32 8.334（ 21╱64） 3.4 4 710 5 410
7.938 CRH 10-1 VB CRH 10-1 VBUU 23 15.875（ 5╱8） 11.112（ 7╱16） 7.938（ 5╱16） 5╱16
 - 24 7.938（ 5╱16） 12.8（0.50） 19.050（ 3╱4）     ─   （   ─  ） 0.794（ 1╱32）     ─   （   ─  ）     ─   （   ─  ） 3.175（ 1╱8）0.397（ 1╱64） 11.112（ 7╱16） 6.8 6 340 8 530
（ 5╱16） CRH 11 VB CRH 11 VBUU 27 17.462（ 11╱16） 11.112（ 7╱16） 7.938（ 5╱16） 5╱16
 - 24 7.938（ 5╱16） 12.8（0.50） 19.050（ 3╱4）     ─   （   ─  ） 0.794（ 1╱32）    ─   （   ─  ）        ─   （   ─  ） 3.175
    （ 1╱8）0.397（ 1╱64） 11.112（ 7╱16） 6.8 6 340 8 530
11.112 CRH 12 VB CRH 12 VBUU 39 19.050（ 3╱4） 12.700（ 1╱2） 11.112（ 7╱16） 7╱16
 - 20 9.525（ 3╱8） 14.6（0.57） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 4.762（ 3╱16）0.794（ 1╱32） 13.494（ 17╱32） 17.6 8 710 12 300
（ 7╱16） CRH 14 VB CRH 14 VBUU 49 22.225（ 7╱8） 12.700（ 1╱2） 11.112（ 7╱16） 7╱16
 - 20 9.525（ 3╱8） 14.6（0.57） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 4.762（ 3╱16）0.794（ 1╱32） 13.494（ 17╱32） 17.6 8 710 12 300
15.875 CRH 16 VB CRH 16 VBUU 93 25.400（1 ） 15.875（ 5╱8） 15.875（ 5╱8） 5╱8 - 18 12.700（ 1╱2） 17.9（0.70） 25.400（1 ） 6.350（ 1╱4） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 6.350（ 1╱4）1.191（ 3╱64） 18.256（ 23╱32） 57.8 13 100 22 700
（ 5╱8） CRH 18 VB CRH 18 VBUU 109 28.575（1 1╱8） 15.875（ 5╱8） 15.875（ 5╱8） 5╱8 - 18 12.700（ 1╱2） 17.9（0.70） 25.400（1 ） 6.350（ 1╱4） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 6.350（ 1╱4）1.588（ 1╱16） 18.256（ 23╱32） 57.8 13 100 22 700
19.050 CRH 20 VB CRH 20 VBUU 176 31.750（1 1╱4） 19.050（ 3╱4） 19.050（ 3╱4） 3╱4 - 16 15.875（ 5╱8） 21.0（0.83） 31.750（1 1╱4） 7.938（ 5╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 6.350（ 1╱4）1.588（ 1╱16） 24.209（ 61╱64） 103 23 600 31 700
（ 3╱4） CRH 22 VB CRH 22 VBUU 200 34.925（1 3╱8） 19.050（ 3╱4） 19.050（ 3╱4） 3╱4 - 16 15.875（ 5╱8） 21.0（0.83） 31.750（1 1╱4） 7.938（ 5╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 6.350（ 1╱4）1.588（ 1╱16） 24.209（ 61╱64） 103 23 600 31 700 I
22.225 CRH 24 VB CRH 24 VBUU 296 38.100（1 1╱2） 22.225（ 7╱8） 22.225（ 7╱8） 7╱8 - 14 19.050（ 3╱4） 24.3（0.96） 38.100（1 1╱2） 9.525（ 3╱8） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 7.938（ 5╱16）1.588（ 1╱16） 26.988（1 1╱16） 162 28 200 40 100
（ 7╱8） CRH 26 VB CRH 26 VBUU 329 41.275（1 5╱8） 22.225（ 7╱8） 22.225（ 7╱8） 7╱8 - 14 19.050（ 3╱4） 24.3（0.96） 38.100（1 1╱2） 9.525（ 3╱8） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 7.938（ 5╱16）1.588（ 1╱16） 26.988（1 1╱16） 162 28 200 40 100
25.400 CRH 28 VB CRH 28 VBUU 463 44.450（1 3╱4） 25.400（1 ） 25.400（1 ） 1- 14 UNS 22.225（ 7╱8） 27.4（1.08） 44.450（1 3╱4） 11.112（ 7╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 7.938（ 5╱16）1.588（ 1╱16） 32.941（1 19╱64） 258 35 300 55 600
（ 1 ） CRH 30 VB CRH 30 VBUU 508 47.625（1 7╱8） 25.400（1 ） 25.400（1 ） 1- 14 UNS 22.225（ 7╱8） 27.4（1.08） 44.450（1 3╱4） 11.112（ 7╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 7.938（ 5╱16）1.588（ 1╱16） 32.941（1 19╱64） 258 35 300 55 600
28.575 CRH 32 VB CRH 32 VBUU 722 50.800（2 ） 31.750（1 1╱4） 28.575（1 1╱8） 1 1╱8 - 12 25.400（1 ） 34.2（1.35） 50.800（2 ） 12.700（ 1╱2） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 11.112（ 7╱16）1.588（ 1╱16） 37.306（1 15╱32） 356 45 700 80 600
（1 1╱8） CRH 36 VB CRH 36 VBUU 858 57.150（2 1╱4） 31.750（1 1╱4） 28.575（1 1╱8） 1 1╱8 - 12 25.400（1 ） 34.2（1.35） 50.800（2 ） 12.700（ 1╱2） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 11.112（ 7╱16）1.588（ 1╱16） 37.306（1 15╱32） 356 45 700 80 600
31.750 CRH 40 VB CRH 40 VBUU 1 260 63.500（2 1╱2） 38.100（1 1╱2） 31.750（1 1╱4） 1 1╱4 - 12 28.575（1 1╱8） 40.0（1.57） 57.150（2 1╱4） 14.288（ 9╱16） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 12.700（ 1╱2）2.381（ 3╱32） 40.878（1 39╱64） 500 61 400 116 000
（1 1╱4） CRH 44 VB CRH 44 VBUU 1 460 69.850（2 3╱4） 38.100（1 1╱2） 31.750（1 1╱4） 1 1╱4 - 12 28.575（1 1╱8） 40.0（1.57） 57.150（2 1╱4） 14.288（ 9╱16） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 12.700（ 1╱2）2.381（ 3╱32） 40.878（1 39╱64） 500 61 400 116 000
38.100 CRH 48 VB CRH 48 VBUU 2 100 76.200（3 ） 44.450（1 3╱4） 38.100（1 1╱2） 1 1╱2 - 12 31.750（1 1╱4） 46.4（1.83） 63.500（2 1╱2） 15.875（ 5╱8） 1.588（ 1╱16） 6.350（ 1╱4） 3.175（ 1╱8） 19.050（ 3╱4）2.381（ 3╱32） 51.991（2 3╱64） 892 77 600 172 000
（1 1╱2） CRH 52 VB CRH 52 VBUU 2 380 82.550（3 1╱4） 44.450（1 3╱4） 38.100（1 1╱2） 1 1╱2 - 12 31.750（1 1╱4） 46.4（1.83） 63.500（2 1╱2） 15.875（ 5╱8） 1.588（ 1╱16） 6.350（ 1╱4） 3.175（ 1╱8） 19.050（ 3╱4）2.381（ 3╱32） 51.991（2 3╱64） 892 77 600 172 000
44.450
CRH 56 VB CRH 56 VBUU 3 240 88.900（3 1╱2） 50.800（2 ） 44.450（1 3╱4） 1 3╱4 - 12UN 34.925（1 3╱8） 52.8（2.08） 69.850（2 3╱4） 17.462（ 11╱16） 1.588（ 1╱16） 6.350（ 1╱4） 3.175（ 1╱8） 19.050（ 3╱4）2.381（ 3╱32） 59.928（2 23╱64） 1 450 111 000 239 000
（1 3╱4）
50.800
4 960 101.600（4 ） 57.150（2 1╱4） 50.800（2 ） 2- 12 UN 38.100（1 1╱2） 59.4（2.34） 88.900（3 1╱2） 19.050（ 3╱4） 1.588（ 1╱16） 6.350（ 1╱4） 3.175（ 1╱8） 19.050（ 3╱4）2.381（ 3╱32） 64.691（2 35╱64） 2 190
（ 2 ） CRH 64 VB CRH 64 VBUU
142 000 317 000

Remarks1.   Models with a stud diameter d1 of 7.938 mm or less have no oil hole. Other models are provided with one oil hole each on the
outside surface and end surface of the stud.
2.   Provided with prepacked grease.
3.   For the maximum allowable static load, please contact .

1N=0.102kgf=0.2248lbs.
I71 1mm=0.03937inch
I72
 CAM FOLLOWERS
Inch Series Heavy Duty Cam Followers Full Complement Type/With Screwdriver Slot

B3

g2

f
D

G
g1
d1
G1

R C1 R R

B B2

Stud dia. 6.350−50.800mm CRH … VR CRH … VUUR

Identification number Mass Boundary dimensions　mm(inch) Mounting Maximum Basic dynamic Basic static
Stud (Ref.) dimension tightening load rating load rating
dia. Shield type Sealed type f torque
C C0
mm With crowned With crowned g D C d1 G G1 B B2 B3 C1 g1 g2 R Min.
(inch) outer ring outer ring UNF max mm(inch) N-m N N
6.350 CRH 8-1 VR CRH 8-1 VUUR 12 12.700（ 1╱2） 9.525（ 3╱8） 6.350（ 1╱4） 1╱4 - 28 6.350（ 1╱4） 11.1（0.44） 15.875（ 5╱8） （ 1╱32）
    ─   （   ─  ） 0.794 *3.175（ 1╱8）    ─   （   ─  ） 180（  7） 8.334（ 21╱64） 3.4 4 710 5 410
（ 1╱4） CRH 9 VR CRH 9 VUUR 15 14.288（ 9╱16）
9.525（ 3╱8）
6.350（ 1╱4）
1╱4 - 28 6.350（ 1╱4） 11.1（0.44）
（ 5╱8）
15.875     ─   （   ─  ） 0.794（ ╱32）*3.175（ 1╱8）    ─   （   ─  ）
1 （ 21╱64） 3.4
180（  7） 8.334 4 710 5 410
7.938 CRH 10-1 VR CRH 10-1 VUUR 23 15.875（ 5╱8） 11.112（ 7╱16） 7.938（ 5╱16） 5╱16
 - 24 7.938（ 5╱16） 12.8（0.50） 19.050（ 3╱4）     ─   （   ─  ） 0.794（ 1╱32） *3.175（ 1╱8）    ─   （   ─  ） 200（  8） 11.112（ 7╱16） 6.8 6 340 8 530
（ 5╱16） CRH 11 VR CRH 11 VUUR 27 17.462（ 11╱16） 11.112（ 7╱16） 7.938（ 5╱16） 5╱16
 - 24 7.938（ 5╱16） 12.8（0.50） 19.050（ 3╱4）     ─   （   ─  ） 0.794（ 1╱32）*3.175（ 1╱8）    ─   （   ─  ）    200（  8） 11.112（ 7╱16） 6.8 6 340 8 530
11.112 CRH 12 VR CRH 12 VUUR 39 19.050（ 3╱4） 12.700（ 1╱2） 11.112（ 7╱16） 7╱16
 - 20 9.525（ 3╱8） 14.6（0.57） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 250（10） 13.494（ 17╱32） 17.6 8 710 12 300
（ 7╱16） CRH 14 VR CRH 14 VUUR 49 22.225（ 7╱8） 12.700（ 1╱2） 11.112（ 7╱16） 7╱16
 - 20 9.525（ 3╱8） 14.6（0.57） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32） 250（10） 13.494（ 17╱32） 17.6 8 710 12 300
15.875 CRH 16 VR CRH 16 VUUR 93 25.400（1 ） 15.875（ 5╱8） 15.875（ 5╱8） 5╱8 - 18 12.700（ 1╱2） 17.9（0.70） 25.400（1 ） 6.350（ 1╱4） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 300（12） 18.256（ 23╱32） 57.8 13 100 22 700
（ 5╱8） CRH 18 VR CRH 18 VUUR 109 28.575（1 1╱8） 15.875（ 5╱8） 15.875（ 5╱8） 5╱8 - 18 12.700（ 1╱2） 17.9（0.70） 25.400（1 ） 6.350（ 1╱4） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 300（12） 18.256（ 23╱32） 57.8 13 100 22 700
19.050 CRH 20 VR CRH 20 VUUR 176 31.750（1 1╱4） 19.050（ 3╱4） 19.050（ 3╱4） 3╱4 - 16 15.875（ 5╱8） 21.0（0.83） 31.750（1 1╱4） 7.938（ 5╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 360（14） 24.209（ 61╱64） 103 23 600 31 700
（ 3╱4） CRH 22 VR CRH 22 VUUR 200 34.925（1 3╱8） 19.050（ 3╱4） 19.050（ 3╱4） 3╱4 - 16 15.875（ 5╱8） 21.0（0.83） 31.750（1 1╱4） 7.938（ 5╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 360（14） 24.209（ 61╱64） 103 23 600 31 700 I
22.225 CRH 24 VR CRH 24 VUUR 296 38.100（1 1╱2） 22.225（ 7╱8） 22.225（ 7╱8） 7╱8 - 14 19.050（ 3╱4） 24.3（0.96） 38.100（1 1╱2） 9.525（ 3╱8） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 500（20） 26.988（1 1╱16） 162 28 200 40 100
（ 7╱8） CRH 26 VR CRH 26 VUUR 329 41.275（1 5╱8） 22.225（ 7╱8） 22.225（ 7╱8） 7╱8 - 14 19.050（ 3╱4） 24.3（0.96） 38.100（1 1╱2） 9.525（ 3╱8） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 500（20） 26.988（1 1╱16） 162 28 200 40 100
25.400 CRH 28 VR CRH 28 VUUR 463 44.450（1 3╱4） 25.400（1 ） 25.400（1 ） 1- 14 UNS 22.225（ 7╱8） 27.4（1.08） 44.450（1 3╱4） 11.112（ 7╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 500（20） 32.941（1 19╱64） 258 35 300 55 600
（ 1 ） CRH 30 VR CRH 30 VUUR 508 47.625（1 7╱8） 25.400（1 ） 25.400（1 ） 1- 14 UNS 22.225（ 7╱8） 27.4（1.08） 44.450（1 3╱4） 11.112（ 7╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 500（20） 32.941（1 19╱64） 258 35 300 55 600
28.575 CRH 32 VR CRH 32 VUUR 722 50.800（2 ） 31.750（1 1╱4） 28.575（1 1╱8） 1 1╱8 - 12 25.400（1 ） 34.2（1.35） 50.800（2 ） 12.700（ 1╱2） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 600（24） 37.306（1 15╱32） 356 45 700 80 600
（1 1╱8） CRH 36 VR CRH 36 VUUR 858 57.150（2 1╱4） 31.750（1 1╱4） 28.575（1 1╱8） 1 1╱8 - 12 25.400（1 ） 34.2（1.35） 50.800（2 ） 12.700（ 1╱2） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 600（24） 37.306（1 15╱32） 356 45 700 80 600
31.750 CRH 40 VR CRH 40 VUUR 1 260 63.500（2 1╱2） 38.100（1 1╱2） 31.750（1 1╱4） 1 1╱4 - 12 28.575（1 1╱8） 40.0（1.57） 57.150（2 1╱4） 14.288（ 9╱16） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 760（30） 40.878（1 39╱64） 500 61 400 116 000
（1 1╱4） CRH 44 VR CRH 44 VUUR 1 460 69.850（2 3╱4） 38.100（1 1╱2） 31.750（1 1╱4） 1 1╱4 - 12 28.575（1 1╱8） 40.0（1.57） 57.150（2 1╱4） 14.288（ 9╱16） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8） 760（30） 40.878（1 39╱64） 500 61 400 116 000
38.100 CRH 48 VR CRH 48 VUUR 2 100 76.200（3 ） 44.450（1 3╱4） 38.100（1 1╱2） 1 1╱2 - 12 31.750（1 1╱4） 46.4（1.83） 63.500（2 1╱2） 15.875（ 5╱8） 1.588（ 1╱16） 6.350（ 1╱4）     3.175（ 1╱8） 760（30） 51.991（2 3╱64） 892 77 600 172 000
（1 1╱2） CRH 52 VR CRH 52 VUUR 2 380 82.550（3 1╱4） 44.450（1 3╱4） 38.100（1 1╱2） 1 1╱2 - 12 31.750（1 1╱4） 46.4（1.83） 63.500（2 1╱2） 15.875（ 5╱8） 1.588（ 1╱16） 6.350（ 1╱4）     3.175（ 1╱8） 760（30） 51.991（2 3╱64） 892 77 600 172 000
44.450
CRH 56 VR CRH 56 VUUR 3 240 88.900（3 1╱2） 50.800（2 ） 44.450（1 3╱4） 1 3╱4 - 12UN 34.925（1 3╱8） 52.8（2.08） 69.850（2 3╱4） 17.462（ 11╱16） 1.588（ 1╱16） 6.350（ 1╱4）     3.175（ 1╱8） 760（30） 59.928（2 23╱64） 1 450 111 000 239 000
（1 3╱4）
50.800
4 960 101.600（4 ） 57.150（2 1╱4） 50.800（2 ） 2- 12 UN 38.100（1 1╱2） 59.4（2.34） 88.900（3 1╱2） 19.050（ 3╱4） 1.588（ 1╱16） 6.350（ 1╱4）     3.175（ 1╱8） 760（30） 64.691（2 35╱64） 2 190
（ 2 ） CRH 64 VR CRH 64 VUUR
142 000 317 000

Remarks1.   Models with a stud diameter d1 of 7.938 mm or less (marked *) are provided with an oil hole on the stud head only. Other models
are provided with one oil hole each on the head, outside surface and end surface of the stud.
2.   Provided with prepacked grease.
3.   For the maximum allowable static load, please contact .

1N=0.102kgf=0.2248lbs.
I73 1mm=0.03937inch
I74
 CAM FOLLOWERS
Inch Series Heavy Duty Cam Followers Full Complement Type/With Screwdriver Slot

C
r B3 r
g2

r
r

f
D
g1

g1

G
d1
G1
C1
B B2

Stud dia. 6.350 − 50.800mm CRH … V CRH … VUU

Identification number Mass Boundary dimensions　mm(inch) Mounting Maximum Basic dynamic Basic static
Stud (Ref.) dimension tightening load rating load rating
dia. f torque
C C0
Shield type Sealed type
mm Min.
With cylindrical With cylindrical g D C d1 G G1 B B2 B3 C1 g1 g2 r
(inch) outer ring outer ring UNF max mm(inch) N-m N N
6.350 CRH 8-1 V CRH 8-1 VUU 12 12.700（ 1╱2） 9.525（ 3╱8） 6.350（ 1╱4） 1╱4
 - 28 6.350（ 1╱4） 11.1（0.44） 15.875（ 5╱8） （ 1╱32）
    ─   （   ─  ） 0.794 *3.175（ 1╱8）    ─   （   ─  ）0.397（ 1╱64） 8.334（ 21╱64） 3.4 4 710 5 410
（ 1╱4） CRH 9 V CRH 9 VUU 15 14.228（ 9╱16）
9.525（ 3╱8）
6.350（ 1╱4）
1╱4 - 28 6.350（ 1╱4） 11.1（0.44）
（ 5╱8）
15.875     ─   （   ─  ） 0.794（ ）*3.175（ 1╱8）    ─   （   ─  ）0.397（ 1╱64）
╱
1 32 8.334（ 21╱64） 3.4 4 710 5 410
7.938 CRH 10-1 V CRH 10-1 VUU 23 15.875（ 5╱8） 11.112（ 7╱16） 7.938（ 5╱16） 5╱16
 - 24 7.938（ 5╱16） 12.8（0.50） 19.050（ 3╱4）     ─   （   ─  ） 0.794（ 1╱32） *3.175（ 1╱8）    ─   （   ─  ）0.397（ 1╱64） 11.112（ 7╱16） 6.8 6 340 8 530
（ 5╱16） CRH 11 V CRH 11 VUU 27 17.462（ 11╱16） 11.112（ 7╱16） 7.938（ 5╱16） 5╱16
 - 24 7.938（ 5╱16） 12.8（0.50） 19.050（ 3╱4）     ─   （   ─  ） 0.794（ 1╱32）*3.175（ 1╱8）    ─   （   ─  ）    0.397（ 1╱64） 11.112（ 7╱16） 6.8 6 340 8 530
11.112 CRH 12 V CRH 12 VUU 39 19.050（ 3╱4） 12.700（ 1╱2） 11.112（ 7╱16） 7╱16
 - 20 9.525（ 3╱8） 14.6（0.57） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32）0.794（ 1╱32） 13.494（ 17╱32） 17.6 8 710 12 300
（ 7╱16） CRH 14 V CRH 14 VUU 49 22.225（ 7╱8） 12.700（ 1╱2） 11.112（ 7╱16） 7╱16
 - 20 9.525（ 3╱8） 14.6（0.57） 22.225（ 7╱8） 6.350（ 1╱4） 0.794（ 1╱32） 4.762（ 3╱16） 2.381（ 3╱32）0.794（ 1╱32） 13.494（ 17╱32） 17.6 8 710 12 300
15.875 CRH 16 V CRH 16 VUU 93 25.400（1 ） 15.875（ 5╱8） 15.875（ 5╱8） 5╱8 - 18 12.700（ 1╱2） 17.9（0.70） 25.400（1 ） 6.350（ 1╱4） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32）1.191（ 3╱64） 18.256（ 23╱32） 57.8 13 100 22 700
（ 5╱8） CRH 18 V CRH 18 VUU 109 28.575（1 1╱8） 15.875（ 5╱8） 15.875（ 5╱8） 5╱8 - 18 12.700（ 1╱2） 17.9（0.70） 25.400（1 ） 6.350（ 1╱4） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 1.588（ 1╱16） 18.256（ 23╱32） 57.8 13 100 22 700
19.050 CRH 20 V CRH 20 VUU 176 31.750（1 1╱4） 19.050（ 3╱4） 19.050（ 3╱4） 3╱4 - 16 15.875（ 5╱8） 21.0（0.83） 31.750（1 1╱4） 7.938（ 5╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32）1.588（ 1╱16） 24.209（ 61╱64） 103 23 600 31 700
（ 3╱4） CRH 22 V CRH 22 VUU 200 34.925（1 3╱8） 19.050（ 3╱4） 19.050（ 3╱4） 3╱4 - 16 15.875（ 5╱8） 21.0（0.83） 31.750（1 1╱4） 7.938（ 5╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32）1.588（ 1╱16） 24.209（ 61╱64） 103 23 600 31 700 I
22.225 CRH 24 V CRH 24 VUU 296 38.100（1 1╱2） 22.225（ 7╱8） 22.225（ 7╱8） 7╱8 - 14 19.050（ 3╱4） 24.3（0.96） 38.100（1 1╱2） 9.525（ 3╱8） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32）1.588（ 1╱16） 26.988（1 1╱16） 162 28 200 40 100
（ 7╱8） CRH 26 V CRH 26 VUU 329 41.275（1 5╱8） 22.225（ 7╱8） 22.225（ 7╱8） 7╱8 - 14 19.050（ 3╱4） 24.3（0.96） 38.100（1 1╱2） 9.525（ 3╱8） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32） 1.588（ 1╱16） 26.988（1 1╱16） 162 28 200 40 100
25.400 CRH 28 V CRH 28 VUU 463 44.450（1 3╱4） 25.400（1 ） 25.400（1 ） 1- 14 UNS 22.225（ 7╱8） 27.4（1.08） 44.450（1 3╱4） 11.112（ 7╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32）1.588（ 1╱16） 32.941（1 19╱64） 258 35 300 55 600
（ 1 ） CRH 30 V CRH 30 VUU 508 47.625（1 7╱8） 25.400（1 ） 25.400（1 ） 1- 14 UNS 22.225（ 7╱8） 27.4（1.08） 44.450（1 3╱4） 11.112（ 7╱16） 1.588（ 1╱16） 4.762（ 3╱16） 2.381（ 3╱32）1.588（ 1╱16） 32.941（1 19╱64） 258 35 300 55 600
28.575 CRH 32 V CRH 32 VUU 722 50.800（2 ） 31.750（1 1╱4） 28.575（1 1╱8） 1 1╱8 - 12 25.400（1 ） 34.2（1.35） 50.800（2 ） 12.700（ 1╱2） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8）1.588（ 1╱16） 37.306（1 15╱32） 356 45 700 80 600
（1 1╱8） CRH 36 V CRH 36 VUU 858 57.150（2 1╱4） 31.750（1 1╱4） 28.575（1 1╱8） 1 1╱8 - 12 25.400（1 ） 34.2（1.35） 50.800（2 ） 12.700（ 1╱2） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8）1.588（ 1╱16） 37.306（1 15╱32） 356 45 700 80 600
31.750 CRH 40 V CRH 40 VUU 1 260 63.500（2 1╱2） 38.100（1 1╱2） 31.750（1 1╱4） 1 1╱4 - 12 28.575（1 1╱8） 40.0（1.57） 57.150（2 1╱4） 14.288（ 9╱16） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8）2.381（ 3╱32） 40.878（1 39╱64） 500 61 400 116 000
（1 1╱4） CRH 44 V CRH 44 VUU 1 460 69.850（2 3╱4） 38.100（1 1╱2） 31.750（1 1╱4） 1 1╱4 - 12 28.575（1 1╱8） 40.0（1.57） 57.150（2 1╱4） 14.288（ 9╱16） 1.588（ 1╱16） 4.762（ 3╱16） 3.175（ 1╱8）2.381（ 3╱32） 40.878（1 39╱64） 500 61 400 116 000
38.100 CRH 48 V CRH 48 VUU 2 100 76.200（3 ） 44.450（1 3╱4） 38.100（1 1╱2） 1 1╱2 - 12 31.750（1 1╱4） 46.4（1.83） 63.500（2 1╱2） 15.875（ 5╱8） 1.588（ 1╱16） 6.350（ 1╱4）     3.175（ 1╱8）2.381（ 3╱32） 51.991（2 3╱64） 892 77 600 172 000
（1 1╱2） CRH 52 V CRH 52 VUU 2 380 82.550（3 1╱4） 44.450（1 3╱4） 38.100（1 1╱2） 1 1╱2 - 12 31.750（1 1╱4） 46.4（1.83） 63.500（2 1╱2） 15.875（ 5╱8） 1.588（ 1╱16） 6.350（ 1╱4）     3.175（ 1╱8）2.381（ 3╱32） 51.991（2 3╱64） 892 77 600 172 000
44.450
CRH 56 V CRH 56 VUU 3 240 88.900（3 1╱2） 50.800（2 ） 44.450（1 3╱4） 1 3╱4 - 12UN 34.925（1 3╱8） 52.8（2.08） 69.850（2 3╱4） 17.462（ 11╱16） 1.588（ 1╱16） 6.350（ 1╱4）     3.175（ 1╱8）2.381（ 3╱32） 59.928（2 23╱64） 1 450 111 000 239 000
（1 3╱4）
50.800
4 960 101.600（4 ） 57.150（2 1╱4） 50.800（2 ） 2- 12 UN 38.100（1 1╱2） 59.4（2.34） 88.900（3 1╱2） 19.050（ 3╱4） 1.588（ 1╱16） 6.350（ 1╱4）     3.175（ 1╱8）2.381（ 3╱32） 64.691（2 35╱64） 2 190
（ 2 ） CRH 64 V CRH 64 VUU 142 000 317 000

Remarks1.   Models with a stud diameter d1 of 7.938 mm or less (marked *) are provided with an oil hole on the stud head only. Other models
are provided with one oil hole each on the head, outside surface and end surface of the stud.
2.   Provided with prepacked grease.
3.   For the maximum allowable static load, please contact .

1N=0.102kgf=0.2248lbs.
I75 1mm=0.03937inch
I76
 ■ Structure and Features Structures of Roller Followers
Roller Followers are bearings designed for outer Structure of Separable Roller Follower
ring rotation, in which needle rollers are incorporated Outer ring

in a thick walled outer ring. Both crowned and cylin-

drical outer rings are available. The outer rings run
●Separable Roller Followers ●C-Lube Roller Followers directly on mating cam guide surfaces, and the
●Non-separable Roller Followers ●Cylindrical Roller Followers crowned outer ring is effective in relieving the edge
load caused by mounting errors. The cylindrical outer Inner ring
High carbon steel made
ring, on the other hand, has a large contact area with Needle roller
Stainless steel made the mating cam guide surface and is suitable for appli-
Cage
cations involving large loads or low cam guide surface
hardness.
In Roller Followers, there are two types of bearings
available, the caged type and the full complement Structure of Separable Roller Follower
Outer ring
type. The caged type is useful for applications at
high-speed rotation. The full complement type, on the Side plate
other hand, is suitable for heavy-load applications at
low-speed rotation or oscillating motions.
Roller Followers include separable and non-separable Inner ring
types. Also, in addition to the open type, shield type
Needle roller
and sealed type are available. The clearances
between the side plates and outer ring of the shield Cage
type are narrow, and form labyrinths. In the sealed
type, special synthetic rubber seals are assembled in
these clearances, and they are effective in preventing
penetration of dust and dirt. Structure of Non-separable Roller Follower
Outer ring
These bearings are available in a variety of types to
suit almost any kind of application. They are widely Side plate
used for cam mechanisms and for linear motions of
conveying equipment.
Inner ring

Needle roller
I
Seal

Structure of Cylindrical Roller Follower

Outer ring

Shield plate

Inner ring

Side plate

Cylindrical roller

I77 I78
■ Types ■ Identification Number
In Roller Followers, types shown in Table 1 are avail- Some examples of the identification number of Roller
able. Followers are shown below.
Table 1 Type of Roller Followers
With cage Full complement type
Type
Crowned outer ring Cylindrical outer ring Crowned outer ring Cylindrical outer ring Examples of identification number
Without inner ring Open type RNAST … R RNAST ─ ─
Separable Roller Followers Open type NAST … R   NAST ─ ─
RNAST，NAST With inner ring Shield type NAST … ZZ R   NAST … ZZ ─ ─ Example 1 NAST 10 ZZUU R
Sealed type NAST … ZZUUR   NAST … ZZUU ─ ─
High carbon Shield type NART … R ─ NART … V R ─
Non-separable Roller
steel made Sealed type NART … UU R ─ NART … VUUR ─ Example 2 NART 10 V UU R
Metric series Followers
NART Stainless Shield type NART … F R ─ ─ ─
steel made Sealed type NART … FUU R ─ ─ ─
C-Lube Roller Followers Example 3 NART 15 UU R /SG
Sealed type NART … UUR/SG ─ ─ ─
NART…/SG
Cylindrical Roller Followers
Shield type ─ ─ NURT … R NURT
NURT
Example 4 NART 12 F UU R
Non-separable Roller Followers Shield type ─ ─ CRY    … V R CRY … V
Inch series
CRY Sealed type ─ ─ CRY    … VUUR CRY … VUU
Model code
RNAST Without inner ring
Separable Roller Follower
NAST With inner ring
Separable Roller Followers C-Lube Roller Followers Metric series NART Non-separable Roller Follower
NART…/SG C-Lube Roller Follower
These bearings are assembled by combining an outer These Roller Followers are lubricated with C-Lube, an NURT Cylindrical Roller Follower
ring, inner ring and Needle Roller Cage, which can be original thermosetting solid-type lubricant which Inch series CRY Non-separable Roller Follower
separated from one another. Thus, handling is easy. fills the inner space of the bearing. C-Lube is lubricant
Oil lubrication is also easy, making them suitable for made of a lot of lubricant and fine particles of super- Size

I
The size indicates the bore diameter of the inner ring. (unit: mm)
high-speed rotations. high molecular polyolefin that are solidified by heat
In the inch series, the outer diameter of the outer ring is indicated in
There are two types: type without inner ring RNAST treatment. As the bearing rotates, the lubricant oozes
units of 1/16 inch.
and type with inner ring NAST. The type with inner out onto the raceway in proper quantities, maintaining
ring includes open type, shield type, and sealed type. the lubrication performance for a long period of time. Type of material
No symbol High carbon steel made
Non-separable Roller Followers Cylindrical Roller Followers F(1) Stainless steel made

These non-separable type bearings have side plates These bearings are full complement type bearings Roller guide method
fixed on both sides of the inner ring, and include the incorporating double rows of full complement No symbol With cage
V Full complement type
caged type and the full complement type. Both shield cylindrical rollers in the outer ring, and can withstand
type and sealed type are available. As well, these large radial loads. Seal structure (Separable Roller Follower)
bearings also offer a highly corrosion-resistant stain- Additionally, the outer ring is guided by the outer ring No symbol Open type
less steel specification, of which the products are suit- shoulder and the end face of cylindrical rollers to the ZZ Shield type
able for applications where rust prevention oil is not axial direction. ZZUU Sealed type
preferred, such as in cleanroom environments. Seal structure (Other Roller Follower)
Inch series Non-separable Roller Followers are full No symbol Shield type
complement type bearings with black oxide surface UU Sealed type
treatment.
Shape of outer ring outside surface
R With crowned outer ring
No symbol With cylindrical outer ring
Note(1)　Applicable to Non-separable Roller Followers only

1N=0.102kgf=0.2248lbs.
I79 1mm=0.03937inch
I80
■ Accuracy Table 5 Tolerances of smallest single roller set bore diameter Fws min
Fw ∆ Fws min
unit: μ m

Dimensional accuracy and rotational accuracy of Nominal roller set bore diameter Deviation of smallest single roller set bore diameter
Roller Followers are based on Tables 2, 3 and 4. mm
Tolerances for the smallest single roller set bore Over Incl. High Low
diameter of Separable Roller Followers are shown in   6 10 ＋ 22 ＋ 13
Table 5. Roller Followers with special accuracy can
10 18 ＋ 27 ＋ 16
also be manufactured. Please contact .
18 30 ＋ 33 ＋ 20

Table 2 Tolerances 30 50 ＋ 41 ＋ 25
unit: μ m
50 80 ＋ 49 ＋ 30
Series Metric series Inch series
Crowned Cylindrical Crowned Cylindrical
Dimensions and symbols outer ring outer ring outer ring outer ring
■ Clearance
＋ 5
d ≦ 19.05 Radial internal clearances of Roller Followers are
−   10 ＋ 5
Bore dia. of inner ring d See Table 3. based on Table 6.
＋ 2 −   10
19.05 ＜ d
−   12 Table 6 Radial internal clearance unit: μ m
     0 See Table 4.
      0       0 Identification number（1） Radial internal clearance
Outside dia. of outer ring D
− 50 −   50 −   25
Metric series Inch series
      0       0 Separable Roller Non-separable Roller Cylindrical Roller Non-separable Roller Min. Max.
Width of outer ring C
− 120 − 130 Followers Followers（2） Followers Followers
      0 NAST  6R NART  5R − −   5 20
Width of inner ring B Separable Roller Follower −
− 120
NAST  8R 〜 NAST12R NART  6R 〜 NART12R − −   5 25
Non-separable Roller Follower − ＋ 130 NAST15R 〜 NAST25R NART15R 〜 NART20R − − 10 30
Width of bearing B   h12
Cylindrical Roller Follower h12 − 250 NAST30R 〜 NAST40R NART25R 〜 NART40R − − 10 40

Roller set bore dia. Fw Separable Roller Follower See Table 5. − NAST45R，  NAST50R NART45R，  NART50R − − 15 50
− − NURT15R 〜 NURT30-1R − 20 45
− − NURT35R 〜 NURT40-1R − 25 50
− − NURT45R 〜 NURT50-1R − 30 60
Table 3 Tolerances and allowable values of inner rings (Metric series)
I
unit: μ m
− − − CRY12R 〜 CRY56R 35 60
d ∆ dmp Vdp Vdmp Kia VBs
Nominal bore dia.
− − − CRY64R 45 70
Single plane mean bore dia. Bore dia. variation in Mean bore dia. Radial runout of assembled Width variation
Note(1)　Alsoapplicable to the full complement type, cylindrical outer ring type, shield type and sealed type.
mm deviation a single radial plane variation bearing inner ring
(2)　Also applicable to C-Lube Roller Followers.
Over Incl. High Low (Max.) (Max.) (Max.) (Max.)
  2.5
10
10
18
0
0
− 8
− 8
10
10
6
6
10
10
15
20
■ Fit ■ Maximum allowable static load
Roller Followers are generally used under the loading The load that is applicable to Roller Followers is, in
18 30 0 − 10 13 8 13 20
conditions in which the load direction is fixed in rela- some cases, determined by the strength of the outer
30 50 0 − 12 15 9 15 20
tion to the inner ring and rotates in relation to the ring rather than by the load rating of the needle roller
outer ring. The recommended fits for shafts are bearing. Therefore, the maximum allowable load that
Table 4 Tolerances and allowable values of outer rings (Metric series) unit: μ m shown in Table 7. Those for the inch series are is limited by the strength of outer ring is specified.
D ∆ Dmp VDp（1） VDmp（1） Kea（1） VCs shown in the dimension table.
Nominal outside dia. of outer ring Single plane mean outside dia. Outside dia. variation in Mean outside Radial runout of assembled Width variation
mm deviation a single radial plane dia. variation bearing outer ring Table 7 Recommended fit (Metric series)
Over Incl. High Low (Max.) (Max.) (Max.) (Max.)
Type Tolerance class of shaft
  6   18 0 − 8 10   6 15
Same as the
18   30 0 − 9 12   7 15 tolerance values
without inner ring k5，k6
Separable Roller Followers
30   50 0 − 11 14   8 20 of VBs for d of with inner ring
the inner of the Non-separable Roller Followers(1) g6，h6
50   80 0 − 13 16 10 25
same bearing
80 120   0 − 15 19 11 35 Cylindrical Roller Followers
Note(1)　Also applicable to the inch series. Note(1)　Also applicable to C-Lube Roller Followers.

1N=0.102kgf=0.2248lbs.
I81 1mm=0.03937inch
I82
■ Track Capacity (Tensile strength 1250N/mm2). When the hardness of
the mating cam guide surface differs from 40HRC, the ■ Allowable Rotational Speed 4 In case of Roller Followers without an inner ring,
the shaft requires heat treatment and grinding fin-
Track capacity is defined as the load that can be con- track capacity is obtained by multiplying the value by The allowable rotational speed of Roller Followers is ish. The recommended surface hardness of the
tinuously applied on a Roller Follower placed on a steel the track capacity factor shown in Table 9. affected by mounting and operating conditions. For dn shaft is 58 〜 64HRC, and the recommended rough-
cam guide surface without causing deformation and If lubrication between the outer ring and the mating value with only pure radial load applied, use values in ness of the shaft is 0.2μmR a or less.
indentation on the cam guide surface when the outer cam guide surface is insufficient, seizure and/or wear Table 10 or less as a guideline. Also, the outer ring and cage are guided by side
ring of the Roller Follower makes contact with the mat- may occur depending on the application. Therefore, Considering that axial loads also act under actual surfaces of the mounting parts. Therefore, it is rec-
ing cam guide surface (plane). The track capacities pay attention to lubrication and surface roughness of operating conditions, the recommended dn value is ommended that the side surfaces of the mounting
shown in Tables 8.1 and 8.2 are applicable when the the mating cam guide especially in the case of high- 1/10 of the value shown in the table. parts be finished by grinding or at least by machin-
hardness of the mating cam guide surface is 40HRC speed rotation such as for cam mechanisms. For use with oscillating rotation, use a C-Lube Roller ing.(See Fig. 3.)
Follower dn value of 8,000 or less as a guideline. For 5 In Non-separable Roller Followers, the side plates are
Table 8.1 Track capacity (Metric series) unit: N use with one-way or continuous rotation, please con- press-fitted. Therefore, when mounting the Roller
Roller Followers with crowned outer ring Roller Followers with cylindrical outer ring sult . Followers, do not push the side plates/outer rings.
Table 10 dn values of Roller Followers（1） Pushing on the side plates or outer rings may
Identification number（1）
Track Identification Track Identification Track Identification Track cause unsatisfactory product performance.
（3）
Separable Roller Non-separable Cylindrical capacity number capacity number（2） capacity number capacity
Lubricant
Followers Roller Followers Roller Followers Grease Oil
Type
 RNAST   5R NART  5R −   1 040    RNAST  5   2 310 − − − −
Caged type 84 000 140 000
(R)NAST  6R NART  6R −   1 330 (R)NAST  6   3 550 NAST  6ZZ   3 550 − −
(R)NAST  8R NART  8R −   1 850 (R)NAST  8   3 980 NAST  8ZZ   4 490 − − Full complement type 42 000   70 000
(R)NAST10R NART10R −   2 470 (R)NAST10   5 610 NAST10ZZ   6 890 − − Cylindrical Roller Follower 72 000 120 000
(R)NAST12R NART12R −   2 710 (R)NAST12   5 990 NAST12ZZ   7 350 − −
(R)NAST15R NART15R NURT15  R   3 060 (R)NAST15   6 550 NAST15ZZ   8 030 NURT15 11 500 dn value ＝ d × n
Note(1)　
　　　　 where,   d：Bore diameter of bearing  mm
− − NURT15-1R   3 910 − − − − NURT15-1 13 700
　　　　　　　    n：Rotational speed  min-1
(R)NAST17R NART17R NURT17  R   3 660 (R)NAST17 10 900 NAST17ZZ 11 700 NURT17 13 600
− − NURT17-1R   4 530 − − − − NURT17-1 16 000

■ Lubrication
(R)NAST20R NART20R NURT20  R   4 530 (R)NAST20 12 800 NAST20ZZ 13 800 NURT20 20 000
− − NURT20-1R   5 190 − − − − NURT20-1 22 100
(R)NAST25R NART25R NURT25  R   5 190 (R)NAST25 14 100 NAST25ZZ 15 300 NURT25 22 100
In Sealed Type Roller Followers, Heavy Duty Type
− − NURT25-1R   6 580 − − − − NURT25-1 26 400
(R)NAST30R NART30R NURT30  R   6 580 (R)NAST30 22 100 NAST30ZZ 22 100 NURT30 31 600 Roller Followers and Inch series Roller Followers, Fig. 1 Mating seating dimension "a"
− − NURT30-1R   8 020 − − − − NURT30-1 36 700 ALVANIA GREASE S2 (SHOWA SHELL SEKIYU
(R)NAST35R NART35R NURT35  R   8 020 (R)NAST35 25 700 NAST35ZZ 25 700 NURT35 36 700 K.K.) is prepacked as the lubricating grease.
− − NURT35-1R   9 220 − − − − NURT35-1 40 800 For Roller Followers without prepacked grease, Oil hole
(R)NAST40R NART40R NURT40  R   9 220 (R)NAST40 26 900 NAST40ZZ 30 300 NURT40 44 200 grease or oil should be supplied through the oil hole
− − NURT40-1R 10 800 − − − − NURT40-1 49 700
(R)NAST45R
−
NART45R
−
NURT45  R
NURT45-1R
  9 990
12 400
(R)NAST45
−
28 500
−
NAST45ZZ
−
32 200
−
NURT45
NURT45-1
47 000
55 300
of the inner ring for use. If they are used without lubri-
cation, wear of rolling contact surfaces may take
I
(R)NAST50R NART50R NURT50  R 10 800 (R)NAST50 30 200 NAST50ZZ 34 000 NURT50 49 700 place, leading to a short bearing life.
− − NURT50-1R 14 000 − − − − NURT50-1 60 800

■ Oil Hole
Notes(1)　Also applicable to the full complement type, shield type, and sealed type.　 (3)　Also applicable to C-Lube Roller Followers.
 　　 (2)　Also applicable to the sealed type.

Table 8.2 Track capacity (Inch series) unit: N Table 9 Track capacity factor
Open Type Separable Roller Followers have no oil
Crowned outer ring Cylindrical outer ring Hardness Tensile strength Track capacity factor hole. Inner rings of other types of Metric series Roller Load
Identification Track Identification Track HRC N/mm2 Crowned outer ring Cylindrical outer ring Followers have an oil hole. Inch series inner rings
number（1） capacity number（1） capacity
20 760 0.22 0.37 have an oil groove and an oil hole. Fig. 2 Position of oil hole and load direction
CRY12R 853 CRY12     4 490
CRY14R 1 050 CRY14     5 240 25 840 0.31 0.46

■ Mounting
CRY16R 1 420 CRY16     7 270 30 950 0.45 0.58
CRY18R 1 660 CRY18     7 700 35 1 080 0.65 0.75
CRY20R 2 160 CRY20   10 700 38 1 180 0.85 0.89
CRY22R 2 450 CRY22   11 800 40 1 250 1.00 1.00 1 In case of shield and sealed types, match the side
CRY24R 3 410 CRY24   15 400 42 1 340 1.23 1.15 surface correctly to the mating seating surface indi-
CRY26R 3 820 CRY26   16 700 44 1 435 1.52 1.32 cated by the dimension a shown in the dimension
CRY28R 4 210 CRY28   21 000 46 1 530 1.85 1.51
CRY30R 4 610 CRY30   22 500 table, and fix them. (See Fig. 1.)
48 1 635 2.27 1.73 2 When mounting Roller Followers, pay special atten-
CRY32R 5 690 CRY32   30 800
CRY36R 6 640 CRY36   34 700 50 1 760 2.80 1.99
tion to avoid locating the oil hole of the inner ring
CRY40R 8 970 CRY40   44 900 52 1 880 3.46 2.29
54 2 015 4.21 2.61 within the loading zone. This may lead to a short
CRY44R 10 200 CRY44   49 400
CRY48R 11 400 CRY48   64 300 56 2 150 5.13 2.97 bearing life. (See Fig. 2.)
CRY52R 12 700 CRY52   69 600 58 2 290 6.26 3.39 3 When mounting Sealed Type Separable Roller
CRY56R 14 100 CRY56   87 000 Followers, do not cause the side plates to come off.
CRY64R 16 800 CRY64 113 000 Fig. 3 M
 ounting example of Roller Follower
If they come off, set them again in place taking care without inner ring
Note(1)　Also applicable to the sealed type.
to avoid damaging the seal lips.
1N=0.102kgf=0.2248lbs.
I83 1mm=0.03937inch
I84
 ROLLER FOLLOWERS
Separable Roller Followers, Open Type With Cage/Without Inner Ring Separable Roller Followers, Open Type With Cage/With Inner Ring

Shaft dia. 7 − 60mm RNAST … R RNAST Shaft dia. 6 − 50mm NAST … R NAST

Identification number Mass Boundary dimensions　 Basic dynamic Basic static Identification number Mass Boundary dimensions Basic dynamic Basic static Assembled
(Ref.) mm load rating load rating (Ref.) 　mm load rating load rating inner ring
Shaft Shaft
dia. Open type C C0 dia. Open type C C0
(1) (1) (1)
g
Fw D C rs min d D B C rs min r1s min Fw
mm Crowned outer ring Cylindrical outer ring N N mm Crowned outer ring Cylindrical outer ring g N N

  7 RNAST   5 R RNAST   5     8.9   7 16   7.8 0.3 2 710 2 390   6 NAST   6 R NAST   6   17.8   6 19 10   9.8 0.3 0.3 10 4 160 4 550 LRT  61010 S
10 RNAST   6 R RNAST   6   13.9 10 19   9.8 0.3 4 160 4 550   8 NAST   8 R NAST   8   28   8 24 10   9.8 0.6 0.3 12 5 650 5 890 LRT  81210 S
12 RNAST   8 R RNAST   8   23.5 12 24   9.8 0.6 5 650 5 890 10 NAST 10 R NAST 10   49.5 10 30 12 11.8 1 0.3 14 9 790 9 680 LRT 101412 S
14 RNAST 10 R RNAST 10   42.5 14 30 11.8 1 9 790 9 680 12 NAST 12 R NAST 12   58 12 32 12 11.8 1 0.3 16 10 500 10 900 LRT 121612 S
16 RNAST 12 R RNAST 12   49.5 16 32 11.8 1 10 500 10 900 15 NAST 15 R NAST 15   62 15 35 12 11.8 1 0.3 20 12 400 14 300 LRT 152012 S
20 RNAST 15 R RNAST 15   50 20 35 11.8 1 12 400 14 300 17 NAST 17 R NAST 17 109 17 40 16 15.8 1 0.3 22 17 600 20 900 LRT 172216 S
22 RNAST 17 R RNAST 17   90 22 40 15.8 1 17 600 20 900 20 NAST 20 R NAST 20 157 20 47 16 15.8 1 0.3 25 19 400 24 500 LRT 202516 S
25 RNAST 20 R RNAST 20 135 25 47 15.8 1 19 400 24 500 25 NAST 25 R NAST 25 180 25 52 16 15.8 1 0.3 30 20 800 28 400 LRT 253016 S
30 RNAST 25 R RNAST 25 152 30 52 15.8 1 20 800 28 400 30 NAST 30 R NAST 30 320 30 62 20 19.8 1 0.6 38 30 500 45 400 LRT 303820 S I
38 RNAST 30 R RNAST 30 255 38 62 19.8 1 30 500 45 400 35 NAST 35 R NAST 35 440 35 72 20 19.8 1 0.6 42 32 400 50 600 LRT 354220 S
42 RNAST 35 R RNAST 35 375 42 72 19.8 1 32 400 50 600 40 NAST 40 R NAST 40 530 40 80 20 19.8 1.5 1 50 35 900 61 100 LRT 405020 S
50 RNAST 40 R RNAST 40 420 50 80 19.8 1.5 35 900 61 100 45 NAST 45 R NAST 45 580 45 85 20 19.8 1.5 1 55 37 400 66 400 LRT 455520 S
55 RNAST 45 R RNAST 45 460 55 85 19.8 1.5 37 400 66 400 50 NAST 50 R NAST 50 635 50 90 20 19.8 1.5 1 60 38 900 71 700 LRT 506020 S
60 RNAST 50 R RNAST 50 500 60 90 19.8 1.5 38 900 71 700

Note(1)　　 Minimum allowable value of chamfer dimension r Note(1)　　 Minimum allowable value of chamfer dimension r or r 1
Remarks1.   No oil hole is provided. Remarks1.   No oil hole is provided.
2.   Not provided with prepacked grease. Perform proper lubrication for use. Remarks2.   Not provided with prepacked grease. Perform proper lubrication for use.

1N=0.102kgf=0.2248lbs.
I85 1mm=0.03937inch
I86
 ROLLER FOLLOWERS
Separable Roller Followers, Shield Type With Cage/With Inner Ring
Separable Roller Followers, Sealed Type With Cage/With Inner Ring

Shaft dia. 6 − 50mm NAST … ZZR NAST … ZZ NAST … ZZUUR NAST … ZZUU

Identification number Mass Boundary dimensions　 Basic dynamic Basic static

(Ref.) mm load rating load rating
Shaft
dia. Shield type Sealed type C C0
g
d D B C a e f
mm Crowned outer ring Cylindrical outer ring Crowned outer ring Cylindrical outer ring N N

  6 NAST   6 ZZR NAST   6 ZZ NAST   6 ZZUUR NAST   6 ZZUU   24.5   6 19 14 13.8 14 2.5 0.8 4 160 4 550
  8 NAST   8 ZZR NAST   8 ZZ NAST   8 ZZUUR NAST   8 ZZUU   39   8 24 14 13.8 17.5 2.5 0.8 5 650 5 890
10 NAST 10 ZZR NAST 10 ZZ NAST 10 ZZUUR NAST 10 ZZUU   65 10 30 16 15.8 23.5 2.5 0.8 9 790 9 680
12 NAST 12 ZZR NAST 12 ZZ NAST 12 ZZUUR NAST 12 ZZUU   75 12 32 16 15.8 25.5 2.5 0.8 10 500 10 900
15 NAST 15 ZZR NAST 15 ZZ NAST 15 ZZUUR NAST 15 ZZUU   83 15 35 16 15.8 29 2.5 0.8 12 400 14 300
17 NAST 17 ZZR NAST 17 ZZ NAST 17 ZZUUR NAST 17 ZZUU 135 17 40 20 19.8 32.5 3 1 17 600 20 900
20 NAST 20 ZZR NAST 20 ZZ NAST 20 ZZUUR NAST 20 ZZUU 195 20 47 20 19.8 38 3 1 19 400 24 500
25 NAST 25 ZZR NAST 25 ZZ NAST 25 ZZUUR NAST 25 ZZUU 225 25 52 20 19.8 43 3 1 20 800 28 400
30 NAST 30 ZZR NAST 30 ZZ NAST 30 ZZUUR NAST 30 ZZUU 400 30 62 25 24.8 50.5 4 1.2 30 500 45 400 I
35 NAST 35 ZZR NAST 35 ZZ NAST 35 ZZUUR NAST 35 ZZUU 550 35 72 25 24.8 53.5 4 1.2 32 400 50 600
40 NAST 40 ZZR NAST 40 ZZ NAST 40 ZZUUR NAST 40 ZZUU 710 40 80 26 25.8 61.5 4 1.2 35 900 61 100
45 NAST 45 ZZR NAST 45 ZZ NAST 45 ZZUUR NAST 45 ZZUU 760 45 85 26 25.8 66.5 4 1.2 37 400 66 400
50 NAST 50 ZZR NAST 50 ZZ NAST 50 ZZUUR NAST 50 ZZUU 830 50 90 26 25.8 76 4 1.2 38 900 71 700

Remarks1.   The inner ring has an oil hole.

2.   The sealed type is provided with prepacked grease. The shield type is not provided with prepacked grease. Perform proper
lubrication for use.

1N=0.102kgf=0.2248lbs.
I87 1mm=0.03937inch
I88
 ROLLER FOLLOWERS
Non-separable Roller Followers · With Cage/With Inner Ring
High carbon steel made Full Complement Type/With Inner Ring

Shaft dia. 5 − 40mm NART … R NART … VR NART … UUR NART … VUUR

Identification number Mass Boundary dimensions　 Basic dynamic Basic static Maximum
(Ref.) mm load rating load rating allowable
Shaft Shield type Sealed type
static load
dia. Crowned outer ring Crowned outer ring C C0
d D B C a 　
mm With cage Full complement With cage Full complement g N N N

  5 NART   5 R ─ NART   5 UUR ─   14.5   5 16 12 11 12 3 650 3 680 3 680

─ NART   5 VR ─ NART   5 VUUR   15.1   5 16 12 11 12 6 810 8 370 7 310

  6 NART   6 R ─ NART   6 UUR ─   20.5   6 19 12 11 14 4 250 4 740 4 740

─ NART   6 VR ─ NART   6 VUUR   21.5   6 19 12 11 14 7 690 10 300 10 300

  8 NART   8 R  ─ NART   8 UUR ─   41.5   8 24 15 14 17.5 5 640 5 900 5 900

─ NART   8 VR ─ NART   8 VUUR   42.5   8 24 15 14 17.5 11 800 15 600 15 600

10
NART 10 R ─ NART 10 UUR ─   64.5 10 30 15 14 23.5 8 030 7 540 7 540
─ NART 10 VR ─ NART 10 VUUR   66.5 10 30 15 14 23.5 15 600 18 100 17 500
NART 12 R ─ NART 12 UUR ─   71 12 32 15 14 25.5 8 580 8 470 8 470
I
12
─ NART 12 VR ─ NART 12 VUUR   73 12 32 15 14 25.5 16 800 20 500 18 600

15
NART 15 R ─ NART 15 UUR ─ 102 15 35 19 18 29 13 700 16 400 16 400
─ NART 15 VR ─ NART 15 VUUR 106 15 35 19 18 29 25 200 36 400 24 000

17
NART 17 R ─ NART 17 UUR ─ 149 17 40 21 20 32.5 17 600 21 000 21 000
─ NART 17 VR ─ NART 17 VUUR 155 17 40 21 20 32.5 32 000 46 300 33 100

20
NART 20 R ─ NART 20 UUR ─ 250 20 47 25 24 38 23 000 30 700 30 700
─ NART 20 VR ─ NART 20 VUUR 255 20 47 25 24 38 41 600 67 300 67 300

25
NART 25 R ─ NART 25 UUR ─ 285 25 52 25 24 43 24 700 35 400 35 400
─ NART 25 VR ─ NART 25 VUUR 295 25 52 25 24 43 45 500 79 100 79 100

30
NART 30 R ─ NART 30 UUR ─ 470 30 62 29 28 50.5 33 600 51 400 51 400
─ NART 30 VR ─ NART 30 VUUR 485 30 62 29 28 50.5 59 900 110 000 92 500

35
NART 35 R ─ NART 35 UUR ─ 640 35 72 29 28 53.5 35 700 57 400 57 400
─ NART 35 VR ─ NART 35 VUUR 655 35 72 29 28 53.5 63 100 121 000 121 000

40
NART 40 R ─ NART 40 UUR ─ 845 40 80 32 30 61.5 44 900 81 500 81 500
─ NART 40 VR ─ NART 40 VUUR 865 40 80 32 30 61.5 76 300 164 000 164 000

Remarks1.   The inner ring has an oil hole.

2.   The sealed type is provided with prepacked grease. The shield type is not provided with prepacked grease. Perform proper
lubrication for use.

1N=0.102kgf=0.2248lbs.
I89 1mm=0.03937inch
I90
 ROLLER FOLLOWERS
Non-separable Roller Followers · With Cage/With Inner Ring
High carbon steel made Full Complement Type/With Inner Ring

Shaft dia. 45 − 50mm NART … R NART … VR NART … UUR NART … VUUR

Identification number Mass Boundary dimensions　 Basic dynamic Basic static Maximum
(Ref.) mm load rating load rating allowable
Shaft Shield type Sealed type static load
dia. C C0
Crowned outer ring Crowned outer ring
d D B C a 　
mm With cage Full complement With cage Full complement g N N N

45
NART 45 R ─ NART 45 UUR ─ 915 45 85 32 30 66.5 46 800 88 600 88 600
─ NART 45 VR ─ NART 45 VUUR 935 45 85 32 30 66.5 80 300 181 000 181 000
NART 50 R ─ NART 50 UUR ─ 980 50 90 32 30 76 48 600 95 600 95 600
50
─ NART 50 VR ─ NART 50 VUUR 1 010 50 90 32 30 76 84 300 198 000 198 000

Remarks1.   The inner ring has an oil hole.

2.   The sealed type is provided with prepacked grease. The shield type is not provided with prepacked grease. Perform proper
lubrication for use.

1N=0.102kgf=0.2248lbs.
I91 1mm=0.03937inch
I92
 ROLLER FOLLOWERS ROLLER FOLLOWERS
Non-separable Roller Followers · Stainless Steel Made With Cage/With Inner Ring
C C C C

D
d

d
a

a
a

a
d

d
R500 B R500 B R500 B R500 B

Shaft dia. 5 − 30mm NART … FR NART … FUUR

Boundary dimensions Basic dynamic Basic static Maximum allowable

Identification number Mass (Ref.)
mm load rating load rating static load
Shaft
dia. C C0
Shield type Sealed type g d D B C a N N N
mm

5 NART 5 FR NART 5 FUUR 13 5 16 12 11 12 2 930 2 920 2 920

6 NART 6 FR NART 6 FUUR 19 6 19 12 11 14 3 400 3 790 3 790

8 NART 8 FR NART 8 FUUR 39 8 24 15 14 17.5 4 340 5 510 5 510

10 NART 10 FR NART 10 FUUR 61 10 30 15 14 22.5 6 330 7 830 7 830

12 NART 12 FR NART 12 FUUR 67 12 32 15 14 25.5 6 510 8 400 8 400

15 NART 15 FR NART 15 FUUR 99 15 35 19 18 27.5 9 620 14 700 14 700

17 NART 17 FR NART 17 FUUR 146 17 40 21 20 31 11 800 20 200 20 200

20
25
NART 20 FR NART 20 FUUR 241 20 47 25 24 36.5 16 500 27 700 27 700
I
NART 25 FR NART 25 FUUR 269 25 52 25 24 43 19 800 28 300 28 300

30 NART 30 FR NART 30 FUUR 447 30 62 29 28 50 26 900 41 200 41 200

Remarks1.   The inner ring has an oil hole.

2.   The sealed type is provided with prepacked grease. The shield type is not provided with prepacked grease. Perform proper
lubrication for use.

1N=0.102kgf=0.2248lbs.
I93 1mm=0.03937inch
I94
 ROLLER FOLLOWERS ROLLER FOLLOWERS
C-Lube Roller Followers With Cage/With Inner Ring
C

a
R=500
B

Shaft dia. 5 − 20mm NART … UUR/SG

Identification number Mass Boundary dimensions　 Basic dynamic Basic static Maximum
(Ref.) mm load rating load rating allowable
Shaft static load
dia. C C0
Shield type d D B C a
mm g N N N
5 NART 5 UUR / SG 14.5 5 16 12 11 12 3 650 3 680 3 680
6 NART 6 UUR / SG 20.5 6 19 12 11 14 4 250 4 740 4 740
8 NART 8 UUR / SG 41.5 8 24 15 14 17.5 5 640 5 900 5 900
10 NART 10 UUR / SG 64.5 10 30 15 14 23.5 8 030 7 540 7 540
12 NART 12 UUR / SG 71 12 32 15 14 25.5 8 580 8 470 8 470
15 NART 15 UUR / SG 102 15 35 19 18 29 13 700 16 400 16 400
17 NART 17 UUR / SG 149 17 40 21 20 32.5 17 600 21 000 21 000
20 NART 20 UUR / SG 250 20 47 25 24 38 23 000 30 700 30 700

Remark　This bearing cannot be re-lubricated as thermosetting solid-type lubricant C-Lube fills its inner space.

1N=0.102kgf=0.2248lbs.
I95 1mm=0.03937inch
I96
 ROLLER FOLLOWERS
Cylindrical Roller Followers Full Complement Type/With Inner Ring
C

r
r1

a
D

r1
d
B

Shaft dia. 15 − 50mm NURT … R NURT

Identification number Mass Boundary dimensions　 Basic dynamic Basic static Maximum
(Ref.) mm load rating load rating allowable
Shaft static load
dia. C C0
Crowned outer ring Cylindrical outer ring d D B C a rs min(1) r1s min(1) 　
mm g N N N
NURT 15    R NURT 15     100 15 35 19 18 20 0.6 0.3 23 400 27 300 11 800
15
NURT 15-1 R NURT 15-1 160 15 42 19 18 20 0.6 0.3 23 400 27 300 27 300
NURT 17    R NURT 17 147 17 40 21 20 22 1 0.3 25 200 30 900 20 300
17
NURT 17-1 R NURT 17-1 222 17 47 21 20 22 1 0.3 25 200 30 900 30 900
NURT 20    R NURT 20  245 20 47 25 24 27 1 0.3 38 900 49 000 27 200
20
NURT 20-1 R NURT 20-1 321 20 52 25 24 27 1 0.3 38 900 49 000 49 000
NURT 25    R NURT 25 281 25 52 25 24 31 1 0.3 43 100 58 100 30 000
25
NURT 25-1 R NURT 25-1 450 25 62 25 24 31 1 0.3 43 100 58 100 58 100
NURT 30    R NURT 30 466 30 62 29 28 38 1 0.3 58 200 75 300 35 200
30
NURT 30-1 R NURT 30-1 697 30 72 29 28 38 1 0.3 58 200 75 300 75 300 I
NURT 35    R NURT 35 630 35 72 29 28 44 1 0.6 63 900 88 800 57 000
35
NURT 35-1 R NURT 35-1  840 35 80 29 28 44 1 0.6 63 900 88 800 88 800
NURT 40    R NURT 40     817 40 80 32 30 49 1 0.6 86 500 122 000 75 300
40
NURT 40-1 R NURT 40-1  1 130 40 90 32 30 49 1 0.6 86 500 122 000 122 000
NURT 45    R NURT 45  883 45 85 32 30 53 1 0.6 91 500 135 000 78 700
45
NURT 45-1 R NURT 45-1 1 400 45 100 32 30 53 1 0.6 91 500 135 000 135 000
NURT 50    R NURT 50 950 50 90 32 30 58 1 0.6 96 300 148 000 82 100
50
NURT 50-1 R NURT 50-1 1 690 50 110 32 30 58 1 0.6 96 300 148 000 148 000

Note(1)　　 Minimum allowable value of chamfer dimension r or r1

Remarks1.   The inner ring has an oil hole.
2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I97 1mm=0.03937inch
I98
 ROLLER FOLLOWERS
Non-separable Roller Followers, Inch Series Full Complement Type / With Inner Ring

C C

D
a

a
d
R B R B

Shaft dia. 6.350 − 31.750mm CRY … VR CRY … VUUR

Identification number Mass Boundary dimensions　mm(inch) Basic dynamic Basic static

Shaft (Ref.) Shaft dia.　mm
load rating load rating
dia.
Push fit Drive fit Press fit C C0
mm Shield type Sealed type
(inch) Crowner outer ring Crowned outer ring g d D B C a R
Min. Max. Min. Max. Min. Max. N N
6.350 CRY 12 VR CRY 12 VUUR 27 6.350（ 1╱4） 19.050（ 3╱4） 14.288(0.5625) 12.700（ 1╱2） 14.4(0.567) 250（10） 6.332 6.342 6.348 6.358 6.353 6.363 8 710 12 300
（ 1╱4） CRY 14 VR CRY 14 VUUR 36 （ 1╱4）
6.350 （ 7╱8） 14.288(0.5625)
22.225 （ 1╱2）
12.700 14.4(0.567) 250（10） 6.332 6.342 6.348 6.358 6.353 6.363 8 710 12 300
7.938 CRY 16 VR CRY 16 VUUR 68 7.938（ 5╱16） 25.400（1 ） 17.463(0.6875) 15.875（ 5╱8） 19.6(0.772) 300（12） 7.920 7.930 7.935 7.945 7.940 7.950 13 100 22 700
（ 5╱16） CRY 18 VR CRY 18 VUUR 77 7.938（ 5╱16） 28.575（1 1╱8） 17.463(0.6875) 15.875（ 5╱8） 19.6(0.772) 300（12） 7.920 7.930 7.935 7.945 7.940 7.950 13 100 22 700
9.525 CRY 20 VR CRY 20 VUUR 109 9.525（ 3╱8） 31.750（1 1╱4） 20.638(0.8125) 19.050（ 3╱4） 25.0(0.984) 360（14） 9.507  9.517  9.523 9.533 9.528 9.538 23 600 31 700
（ 3╱8） CRY 22 VR CRY 22 VUUR 136 9.525（ 3╱8） 34.925（1 3╱8） 20.638(0.8125) 19.050（ 3╱4） 25.0(0.984) 360（14） 9.507  9.517  9.523  9.533  9.528 9.538 23 600 31 700
11.112 CRY 24 VR CRY 24 VUUR 186 11.112（ 7╱16） 38.100（1 1╱2） 23.813(0.9375) 22.225（ 7╱8） 28.8(1.134) 500（20） 11.095 11.105 11.110 11.120 11.115 11.125 28 200 40 100
（ 7╱16） CRY 26 VR CRY 26 VUUR 227 11.112（ 7╱16） 41.275（1 5╱8） 23.813(0.9375) 22.225（ 7╱8） 28.8(1.134) 500（20） 11.095 11.105 11.110 11.120 11.115 11.125 28 200 40 100
12.700 CRY 28 VR CRY 28 VUUR 290 12.700（ 1╱2） 44.450（1 3╱4） 26.988(1.0625) 25.400（1 ） 32.7(1.287) 500（20） 12.682 12.692 12.698 12.708 12.708 12.718 35 300 55 600
（ 1╱2） CRY 30 VR CRY 30 VUUR 363 12.700（ 1╱2） 47.625（1 7╱8） 26.988(1.0625) 25.400（1 ） 32.7(1.287) 500（20） 12.682 12.692 12.698 12.708 12.708 12.718 35 300 55 600 I
15.875 CRY 32 VR CRY 32 VUUR 476 15.875（ 5╱8） 50.800（2 ） 33.338(1.3125) 31.750（1 1╱4） 36.0(1.417) 600（24） 15.857 15.867 15.873 15.883 15.883 15.893 45 700 80 600
（ 5╱8） CRY 36 VR CRY 36 VUUR 599 15.875（ 5╱8） 57.150（2 1╱4） 33.338(1.3125) 31.750（1 1╱4） 36.0(1.417) 600（24） 15.857 15.867 15.873 15.883 15.883 15.893 45 700 80 600
19.050 CRY 40 VR CRY 40 VUUR 816 19.050（ 3╱4） 63.500（2 1╱2） 39.688(1.5625) 38.100（1 1╱2） 43.3(1.705) 760（30） 19.032 19.042 19.048 19.058 19.058 19.068 61 400 116 000
（ 3╱4） CRY 44 VR CRY 44 VUUR 1 020 19.050（ 3╱4） 69.850（2 3╱4） 39.688(1.5625) 38.100（1 1╱2） 43.3(1.705) 760（30） 19.032 19.042 19.048 19.058 19.058 19.068 61 400 116 000
25.400 CRY 48 VR CRY 48 VUUR 1 410 25.400（1 ） 76.200（3 ） 46.038(1.8125) 44.450（1 3╱4） 54.0(2.125) 760（30） 25.377 25.390 25.397 25.410 25.408 25.420 77 600 172 000
（1） CRY 52 VR CRY 52 VUUR 1 640 25.400（1 ） 82.550（3 1╱4） 46.038(1.8125) 44.450（1 3╱4） 54.0(2.125) 760（30） 25.377 25.390 25.397 25.410 25.408 25.420 77 600 172 000
28.575
CRY 56 VR CRY 56 VUUR 2 250 28.575（1 1╱8） 88.900（3 1╱2） 52.388(2.0625) 50.800（2 ） 61.9(2.437) 760（30） 28.522 28.565 28.572 28.585 28.583 28.595 111 000 239 000
（1 1╱8）
31.750
CRY 64 VR CRY 64 VUUR 3 200 31.750（1 1╱4）101.600（4 ） 58.738(2.3125) 57.150（2 1╱4） 71.0(2.797) 760（30） 31.727 31.740 31.747 31.760 31.758 31.770 142 000 317 000
（1 1╱4）

Remarks1.   The inner ring has an oil groove and an oil hole.

2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I99 1mm=0.03937inch
I100
 ROLLER FOLLOWERS
Non-separable Roller Followers, Inch Series Full Complement Type /With Inner Ring
C C

r r

r
r
D

a
d
d

a
B B

Shaft dia. 6.350 − 31.750mm CRY … V CRY … VUU

Identification number Mass Boundary dimensions　mm(inch) Basic dynamic Basic static

Shaft (Ref.) Shaft dia.　mm
load rating load rating
dia.
Push fit Drive fit Press fit C C0
mm Shield type Sealed type
(inch) Cylindrical outer ring Cylindrical outer ring g d D B C a r
Min. Max. Min. Max. Min. Max. N N
6.350 CRY 12 V CRY 12 VUU 27 6.350（ 1╱4） 19.050（ 3╱4） 14.288(0.5625) 12.700（ 1╱2） 14.4(0.567) 0.794（ 1╱32） 6.332 6.342 6.348 6.358 6.353 6.363 8 710 12 300
（ 1╱4） CRY 14 V CRY 14 VUU 36 （ 1╱4）
6.350 （ 7╱8） 14.288(0.5625)
22.225 （ 1╱2）
12.700 14.4(0.567) 0.794 （ 1╱32） 6.332 6.342 6.348 6.358 6.353 6.363 8 710 12 300
7.938 CRY 16 V CRY 16 VUU 68 7.938（ 5╱16） 25.400（1 ） 17.463(0.6875) 15.875（ 5╱8） 19.6(0.772) 1.191（ 3╱64） 7.920 7.930 7.935 7.945 7.940 7.950 13 100 22 700
（ 5╱16） CRY 18 V CRY 18 VUU 77 7.938（ 5╱16） 28.575（1 1╱8） 17.463(0.6875) 15.875（ 5╱8） 19.6(0.772) 1.588（ 1╱16） 7.920 7.930 7.935 7.945 7.940 7.950 13 100 22 700
9.525 CRY 20 V CRY 20 VUU 109 9.525（ 3╱8） 31.750（1 1╱4） 20.638(0.8125) 19.050（ 3╱4） 25.0(0.984) 1.588（ 1╱16） 9.507  9.517  9.523 9.533 9.528 9.538 23 600 31 700
（ 3╱8） CRY 22 V CRY 22 VUU 136 9.525（ 3╱8） 34.925（1 3╱8） 20.638(0.8125) 19.050（ 3╱4） 25.0(0.984) 1.588（ 1╱16） 9.507  9.517  9.523  9.533  9.528 9.538 23 600 31 700
11.112 CRY 24 V CRY 24 VUU 186 11.112（ 7╱16） 38.100（1 1╱2） 23.813(0.9375) 22.225（ 7╱8） 28.8(1.134) 1.588（ 1╱16） 11.095 11.105 11.110 11.120 11.115 11.125 28 200 40 100
（ 7╱16） CRY 26 V CRY 26 VUU 227 11.112（ 7╱16） 41.275（1 5╱8） 23.813(0.9375) 22.225（ 7╱8） 28.8(1.134) 1.588（ 1╱16） 11.095 11.105 11.110 11.120 11.115 11.125 28 200 40 100
12.700 CRY 28 V CRY 28 VUU 290 12.700（ 1╱2） 44.450（1 3╱4） 26.988(1.0625) 25.400（1 ） 32.7(1.287) 1.588（ 1╱16） 12.682 12.692 12.698 12.708 12.708 12.718 35 300 55 600
（ 1╱2） CRY 30 V CRY 30 VUU 363 12.700（ 1╱2） 47.625（1 7╱8） 26.988(1.0625) 25.400（1 ） 32.7(1.287) 1.588（ 1╱16） 12.682 12.692 12.698 12.708 12.708 12.718 35 300 55 600 I
15.875 CRY 32 V CRY 32 VUU 476 15.875（ 5╱8） 50.800（2 ） 33.338(1.3125) 31.750（1 1╱4） 36.0(1.417) 1.588（ 1╱16） 15.857 15.867 15.873 15.883 15.883 15.893 45 700 80 600
（ 5╱8） CRY 36 V CRY 36 VUU 599 15.875（ 5╱8） 57.150（2 1╱4） 33.338(1.3125) 31.750（1 1╱4） 36.0(1.417) 1.588（ 1╱16） 15.857 15.867 15.873 15.883 15.883 15.893 45 700 80 600
19.050 CRY 40 V CRY 40 VUU 816 19.050（ 3╱4） 63.500（2 1╱2） 39.688(1.5625) 38.100（1 1╱2） 43.3(1.705) 2.381（ 3╱32） 19.032 19.042 19.048 19.058 19.058 19.068 61 400 116 000
（ 3╱4） CRY 44 V CRY 44 VUU 1 020 19.050（ 3╱4） 69.850（2 3╱4） 39.688(1.5625) 38.100（1 1╱2） 43.3(1.705) 2.381（ 3╱32） 19.032 19.042 19.048 19.058 19.058 19.068 61 400 116 000
25.400 CRY 48 V CRY 48 VUU 1 410 25.400（1 ） 76.200（3 ） 46.038(1.8125) 44.450（1 3╱4） 54.0(2.125) 2.381（ 3╱32） 25.377 25.390 25.397 25.410 25.408 25.420 77 600 172 000
（1） CRY 52 V CRY 52 VUU 1 640 25.400（1 ） 82.550（3 1╱4） 46.038(1.8125) 44.450（1 3╱4） 54.0(2.125) 2.381（ 3╱32） 25.377 25.390 25.397 25.410 25.408 25.420 77 600 172 000
28.575
CRY 56 V CRY 56 VUU 2 250 28.575（1 1╱8） 88.900（3 1╱2） 52.388(2.0625) 50.800（2 ） 61.9(2.437) 2.381（ 3╱32） 28.522 28.565 28.572 28.585 28.583 28.595 111 000 239 000
（1 1╱8）
31.750
CRY 64 V CRY 64 VUU 3 200 31.750（1 1╱4）101.600（4 ） 58.738(2.3125) 57.150（2 1╱4） 71.0(2.797) 2.381（ 3╱32） 31.727 31.740 31.747 31.760 31.758 31.770 142 000 317 000
（1 1╱4）

Remarks1.   The inner ring has an oil groove and an oil hole.

2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
I101 1mm=0.03937inch
I102
 ■ Structure and Features
Crossed Roller Bearings are compact bearings
with their rollers alternately crossed at right angles to
each other between inner and outer rings. They can
take loads from any directions at the same time such
●High Rigidity Type Crossed Roller Bearings (V) as radial, thrust and moment loads. The rollers make
●Standard Type Crossed Roller Bearings line-contact with raceway surfaces, and, therefore,
elastic deformation due to bearing loads is very small.
●Super Slim Type Crossed Roller Bearings These bearings are widely used in the rotating parts
of industrial robots, machine tools, medical equip-
●Slim Type Crossed Roller Bearings ment, etc., which require compactness, high rigidity
●Mounting Holed Type High Rigidity Crossed Roller Bearings (V) and high rotational accuracy.
In addition, bearings made of stainless steel or those
with inner and outer rings provided with mounting
holes are also available on request. Please contact
.

Structure of Crossed Roller Bearings

High Rigidity Type Crossed Roller Bearings (V) Standard Type Crossed Roller Bearings Standard Type Crossed Roller Bearings
CRBH(V) A
Outer ring
Outer ring
Outer ring separation
Outer ring Cage prevention bolt
Outer ring separation
Roller Seal prevention bolt
Roller
Separator
Inner ring Roller

Inner ring Inner ring

Super Slim Type Crossed Roller Bearings Slim Type Crossed Roller Bearings Mounting Holed Type High Rigidity Crossed Roller Bearings (V)
CRBF(V) A
J
Outer ring

Outer ring
Outer ring Cage
Roller
Roller
Roller Separator
Separator
Inner ring Inner ring
Inner ring

J1 J2
■ Types
Crossed Roller Bearings are available in the types
shown in Table 1.
■Features of Super Slim Type Crossed Roller Bearing CRBT
Table 1 Crossed Roller Bearing Type

Type With Cage With Separator Full complement The world's thinnest roller type! ■Comparison of bearing bore diameter 50 mm

High Rigidity Type Crossed Roller Bearings (V) Open type ─ CRBH(V) … A ─ Very low cross sectional height of 5.5 mm 13
CRBH(V) Sealed type ─ CRBH(V) … AUU ─ The cross sectional height is reduced by 69% in 8
Standard Type Crossed Roller Bearings Open type CRBC ─ CRB comparison with CRBS, which was 5

15
5.5

8
CRBC，CRB Sealed type CRBC … UU ─ CRB   …   UU the thinnest before (bearing 5mm
Super Slim Type Crossed Roller Bearings bore diameter 50 mm). Sectional shape
Open type ─ CRBT … A ─ The width is also as small
CRBT
as 5 mm and the cross 5.5 mm
Slim Type Crossed Roller Bearings Open type CRBS ─ CRBS … V
sectional area is reduced
CRBS Sealed type ─ CRBS … AUU CRBS … VUU by 43% in comparison with
Mounting Holed Type High Rigidity Crossed Roller Bearings (V) Open type ─ CRBF(V) … A ─ conventional products.
CRBT
CRBF(V) Sealed type ─ CRBF(V) … AUU ─ Series Super Slim Slim High rigidity
Item CRBT505A CRBS508 CRBH5013A
Outer diameter mm 61 66 80
Significant weight saving by 38% in comparison mm 5 8 13
Width
High Rigidity Type Crossed Roller Bearings Slim Type Crossed Roller Bearings
with conventional types was realized Sectional height mm 5.5 8 15
C N 2280 4900 17300
Both inner and outer rings have a solid one-piece These bearings are slim bearings having a small out-
Weight reduction is thoroughly pursued. The mass C0 N 3200 6170 20900
construction. Therefore, high accuracy and high rigid- side diameter, in comparison with the bore diameter,
ratio is 0.38 and significant weight saving was Mass g 32.3 84 290
ity are achieved, and mounting errors can be mini- and a narrow width. The type with cage and the type
realized in comparison with conventional slim type Compared with CRBH 0.11 0.29 1.00
mized. As separators are incorporated between the with separator provide smooth rotation and are suit- Compared with CRBS 0.38 1.00 3.45
cylindrical rollers for smooth rotation, these bearings able for applications where rotational speed is com- CRBS (bearing bore diameter 50 mm).
are suitable for applications where rotational speed is paratively high.
comparatively high.
■Features of Mounting Holed Type High Rigidity Crossed Roller Bearing (V) CRBF(V)
Mounting Holed Type
Standard Type Crossed Roller Bearings High Rigidity Crossed Roller Bearings uired
r e is not req tion
uc t u alla
The outer ring is made of two split pieces, which are
Mounting holes are prepared on outer ring and inner High rigidity and high accuracy o u n t ing str lt-on inst
bolted together to prevent separation during trans- lex m Easy bo
portation or mounting. So, handling is easy.
ring providing easy mounting together with high rigidity Comp
J
and high accuracy.
The single structure to reduce the mounting errors is
adopted for both inner and outer rings. Further,
Super Slim Type Crossed Roller Bearings High Rigidity Type Crossed Roller Bearings V mounting holes for direct fixing on mating mounting
Mounting Holed Type High Rigidity Crossed surface are available. So high rigidity and high accuracy
This Type is extremely compact bearing having Roller Bearings V guide can be easily realized, being less subject to the With mounting holes
5.5mm of sectional height and 5mm of width.
structure of the housing and the accuracy.
Separators are incorporated between Cylindrical While the basic performance is on a level with that of No division for both
rollers for smooth rotation. These compactness, light- High Rigidity Crossed Roller Bearings and Mounting inner and outer rings
and high rigidity
ness and smoothness contribute downsizing of the Holed Type High Rigidity Crossed Roller Bearings, the
machine and saving driving power. establishment of a dedicated production site and the
Contributing to miniaturization single structure

revision of design and manufacturing processes have

enabled cost reductions and shortened lead times. It can be easily mounted to a device with bolts without
This product contributes to machinery/equipment cost need for housing and fixing plate, so surrounding
reductions and shorter delivery times. parts of the bearing can be made compact. Single structure for both inner and outer rings!
Further, it allows for reduction of the number of parts Mounting Holed Type High Rigidity Crossed Roller Bearing (V)
and assembly processes, which contributes to CRBF(V)
miniaturization and weight saving of devices.

1N=0.102kgf=0.2248lbs.
J3 1mm=0.03937inch
J4
■ Internal Structures and Shapes ■ Identification number
Various types are lined up in Crossed Roller Bearing The identification number of Crossed Roller Bearings
series, including the type with cage, the type with sep- consists of a model code, dimensions, any supple-
arator, open type, sealed type, etc.. mental codes and a classification symbol. Some
examples are shown below.

Examples of identification number Supplemental Classification

Model code Dimensions code symbol

  Roller guide method Example 1 CRBHV 150 25 A UU C1 P6

Crossed Roller Bearings include the type with cage, paratively high speed rotations, while the full comple-
type with separator and full complement type. The ment type is suitable for heavy load applications at Example 2 CRBC 150 25 UU C1 P6
type with cage and the type with separator have a low speed rotations.
small coefficient of friction and are suitable for com-
Example 3 CRBT 30 5 A C1

《With Cage》 《With Separator》 《Full complement》 Example 4 CRBS 150 8 A UU C1

Roller Outer ring Roller Outer ring Roller Outer ring Example 5 CRBFV 115 28 A D UU C1 RP6
Outer ring Separator Outer ring
separation separation
prevention bolt prevention bolt Model code
Inner ring CRBH(V)･･･A High Rigidity Type Crossed Roller Bearing (V) (With separator)
Cage Inner ring Inner ring
Roller Outer ring Roller Outer ring Roller Outer ring CRBC Standard Type Crossed Roller Bearing (With cage)
Outer ring Separator Outer ring Standard Type Crossed Roller Bearing (Full complement)
CRB
separation separation
prevention bolt prevention bolt CRBT･･･A Super Slim Type Crossed Roller Bearing (With separator)
Inner ring CRBS Slim Type Crossed Roller Bearing (With cage)
Cage Inner ring Inner ring
CRBS･･･A Slim Type Crossed Roller Bearing (With separator)
CRBS･･･V Slim Type Crossed Roller Bearing (Full complement)
CRBF(V)･･･A Mounting Holed Type High Rigidity Crossed Roller Bearing (V) (With separator)
Dimension
The dimension indicates the bore diameter of the bearing. (unit : mm)
The dimension indicates the bearing width. (unit : mm)
Supplemental code - 1(1)
T With female threaded mounting holes on the inner ring
No symbol With counter-bored mounting holes on both inner ring and outer ring in the same direction.
  Seal structure D With counter-bored mounting holes on both inner ring and outer ring in the opposite direction.
Crossed Roller Bearings include the open type and excellent sealing performance against dust and dirt Note(1) Applicable to Mounting Holed Type High Rigidity Crossed Roller Bearing (V).

J
sealed type. The sealed type bearing incorporates penetration and grease leakage. However, excess Supplemental code - 2
seals made of special synthetic rubber that have grease may be discharged during initial operations. No symbol Open type
For application,
UU Sealed type
please see table 2.
U One side sealed type
《Open type》 《Sealed type》 Supplemental code - 3
T1 : T1 clearance
C1 : C1 clearance For application,
Seal C2 : C2 clearance please see table 3.
No symbol : Normal clearance
Classification symbol
No symbol Accuracy class 0
Seal P6 Accuracy class 6
P5 Accuracy class 5
P4 Accuracy class 4
P2 Accuracy class 2 For application, please see table 4.
RP6 Rotational accuracy class 6
RP5 Rotational accuracy class 5
RP4 Rotational accuracy class 4
RP2 Rotational accuracy class 2
Rotational accuracy class···classes specifying accuracy standards for only rotational
accuracy (radial runout, axial runout).

1N=0.102kgf=0.2248lbs.
J5 1mm=0.03937inch
J6
Table 2 Seal Specification
No
■ Dynamic Equivalent Load ■ Accuracy
Model code UU U The direction of basic dynamic load rating of Crossed The accuracy of Crossed Roller Bearings, Super Slim Rigidity Crossed Roller Bearings is shown below in
Symbol
Roller Bearing is the radial direction. When a load in Type Crossed Roller Bearings, Slim Type Crossed Table 6 - 10.2.
CRBH(V) … A 〇 〇 − any direction other than the direction of basic dynamic
Roller Bearings and Mounting Holed Type High Bearings with special accuracy are also options.
load rating or a complex load is applied, calculate the
CRBC 〇 〇 〇 dynamic equivalent load to Please consult .
    calculate the rating life.
（　   　  ）
CRB 〇 〇 〇 　　　   2M Table 6 Tolerances and allowable values of inner rings and tolerances of outer ring width
Pr ＝ X   Fr ＋
　　　　　　  　　 Dpw ＋ YFa  …………………(1) unit: μ m
CRBT … A 〇 − − d ∆ d mp（1） ∆ Bs ∆ Cs（2）
　　where, 　 Pr    : Dynamic equivalent radial load,　  N Kia Sia
CRBS 〇 − − 　　　　　　 Fr    : Radial load, 　 N Nominal bore Single plane mean bore dia. deviation Deviation of Deviation of Radial run-out of assembled Assembled bearing inner ring
diameter a single a single bearing inner ring face run-out with raceway
CRBS … A − 〇 〇 　　　　　　 Fa    : Axial load,  　N inner ring outer ring
Class 0
　　　　　　 M   : Moment,  　N-mm mm P6 P5 P4 width width Class P6 P5 P4 P2 Class P6 P5 P4 P2
CRBS … V 〇 〇 〇 RP6-2
　　　　　　Dpw   : Pitch circle diameter of roller set,　mm Over Incl. High Low High Low High Low High Low High Low High Low 0 RP6 RP5 RP4 RP2 0 RP6 RP5 RP4 RP2

（　       　  ）
CRBF(V) … A 〇 〇 − 　　　　　　　　　　　　  　　    d ＋ D
　　　　　　　　　　　　　　　 Dpw ≒ 2 18 30 0 − 10 0 −   8 0 −   6 0 −   5 0 −   75 0 − 100 13 8 4 3 2.5 13 8 4 3 2.5
　　　　　　   X   : Radial load factor (Refer to Table 5.)
30 50 0 − 12 0 − 10 0 −   8 0 −   6 0 −   75 0 − 100 15 10 5 4 2.5 15 10 5 4 2.5
Table 3 Clearance Specification 　　　　　　 　Y  : Axial load factor (Refer to Table 5.) 50 80 0 − 15 0 − 12 0 −   9 0 −   7 0 −   75 0 − 100 20 10 5 4 2.5 20 10 5 4 2.5
80 120 0 − 20 0 − 15 0 − 10 0 −   8 0 −   75 0 − 100 25 13 6 5 2.5 25 13 6 5 2.5
No
Model code T1 C1 C2 120 150 0 − 25 0 − 18 0 − 13 0 − 10 0 − 100 0 − 120 30 18 8 6 2.5 30 18 8 6 2.5
Symbol
150 180 0 − 25 0 − 18 0 − 13 0 − 10 0 − 100 0 − 120 30 18 8 6 5 30 18 8 6 5
CRBH(V) … A 〇 〇 〇 − 180 250 0 − 30 0 − 22 0 − 15 0 − 12 0 − 100 0 − 120 40 20 10 8 5 40 20 10 8 5
CRBC 〇 〇 〇 − 250 315 0 − 35 0 − 25 0 − 18 − − 0 − 120 0 − 150 50 25 13 10 7 50 25 13 10 7
315 400 0 − 40 0 − 30 0 − 23 − − 0 − 150 0 − 200 60 30 15 12 8 60 30 15 12 8
CRB 〇 〇 〇 −
400 500 0 − 45 0 − 35 − − − − 0 − 150 0 − 200 65 35 18 14 10 65 35 18 14 10
CRBT …A − 〇 − − 500 630 0 − 50 0 − 40 − − − − 0 − 150 0 − 200 70 40 20 16 12 70 40 20 16 12
CRBS 〇 〇 − 〇 630 800 0 − 75 − − − − − − 0 − 150 0 − 200 80 50 25 20 15 80 50 25 20 15
Notes(1)　For accuracy class P2 and other classes without a numerical description, the highest grade numerical value among the lower accura-
CRBS …A 〇 〇 − 〇
cy classes in the same nominal bore diameter range is applied.
CRBS …V 〇 〇 − 〇 (2)　For High Rigidity Type Crossed Roller Bearings (V), the tolerances for deviation of a single inner ring width are applicable to those of a
single outer ring width.
CRBF(V) … A 〇 〇 〇 − Remark　 The accuracy specified in this table is not applicable to Mounting Holed Type High Rigidity Crossed Roller Bearings (V), Slim Type
Crossed Roller Bearings and Super Slim Type Crossed Roller Bearings.

Fig. 1 Load direction Table 7 Tolerances and allowable values of outer ring unit: μ m
Table 4 Accuracy Class
D ∆ Dmp（1） Kea Sea
No P6 P5 P4 P2 Table 5 Radial load factor and axial load factor
Model code Nominal Single plane mean outside dia. deviation Radial run-out of assembled bearing Assembled bearing outer ring face
Symbol RP6 RP5 RP4 RP2 outside
Conditions X Y outer ring run-out with raceway
diameter
CRBH(V) … A 〇 〇 〇 〇 〇 Class 0
mm P6 P5 P4 （2） P2
（2）Class P6 （2） P2
（2）
　　　　　  Fa RP6-2 Class P6 P5 P4 P5 P4
CRBC 〇 〇 〇 〇 〇 ≦ 1.5 1 0.45
CRB 〇 〇 〇 〇 〇
Fr ＋ 2M/Dpw  
　　　　　  Fa　
Over
30
Incl. High Low
50 0 −   11
High
0
Low
−   9
High
0
Low
−   7
High
0
Low
−   6
0
20
RP6
10
RP5 RP4 RP2
7
0
5
RP6
2.5 20 10
RP5 RP4 RP2
7 5 2.5
J
CRBT …A 〇 − − − − ＞ 1.5 0.67 0.67
Fr ＋ 2M/Dpw   50 80 0 −   13 0 − 11 0 −   9 0 −   7 25 13 8 5 4 25 13 8 5 4
CRBS 〇 − − − − 80 120 0 −   15 0 − 13 0 − 10 0 −   8 35 18 10 6 5 35 18 10 6 5
…A 〇 − − − −
■ Static Equivalent Load −   18 − 15 − 11 −   9
CRBS 120 150 0 0 0 0 40 20 11 7 5 40 20 11 7 5
CRBS …V 〇 − − − − 150 180 0 −   25 0 − 18 0 − 13 0 − 10 45 23 13 8 5 45 23 13 8 5
The direction of basic static load rating of Crossed 180 250 0 −   30 0 − 20 0 − 15 0 − 11 50 25 15 10 7 50 25 15 10 7
CRBF(V) … A 〇 〇 〇 〇 〇 Roller Bearing is the radial direction. When a load in
any direction other than the direction of basic static 250 315 0 −   35 0 − 25 0 − 18 0 − 13 60 30 18 11 7 60 30 18 11 7
load rating or a complex load is applied, calculate the 315 400 0 −   40 0 − 28 0 − 20 − − 70 35 20 − − 70 35 20 − −
static equivalent load to calculate the static safety fac-
400 500 0 −   45 0 − 33 0 − 23 − − 80 40 23 − − 80 40 23 − −
tor.  
　　　   2M 500 630 0 −   50 0 − 38 0 − 28 − − 100 50 25 − − 100 50 25 − −
P0 r ＝ Fr ＋ pw ＋ 0.44 Fa …………………(2)
　　　　　   　　D 630 800 0 −   75 0 − 45 − − − − 120 60 30 − − 120 60 30 − −
　　where,　 P0r    : Static equivalent radial load, 　N
800 1000 0 − 100 0 − 60 − − − − 120 75 35 − − 120 75 35 − −
　　　　　　 Fr    : Radial load, 　N
1000 1030 0 − 125 − − − − − − 120 75 35 − − 120 75 35 − −
　　　　　　 Fa    : Axial load, 　N
　　　　　　 M   : Moment, 　N -mm Notes(1)　For accuracy class P2 and other classes without a numerical description, the highest grade numerical value among the lower accura-
cy classes in the same nominal bore diameter range is applied.
　　　　　　Dpw   : Pitch circle diameter of roller set, mm (2)　P4 and P2 apply to High Rigidity Type Crossed Roller Bearings (V). For Standard Type Crossed Roller Bearings, the tolerance values

（　       　  ）
　　　　　　　　　　　　　　　   d ＋ D for P5 are applicable to P4 and P2.
Dpw ≒ 2
　　　　　　　　　　　　　　　 Remark　 The accuracy specified in this table is not applicable to Mounting Holed Type High Rigidity Crossed Roller Bearings (V), Slim Type
Crossed Roller Bearings and Super Slim Type Crossed Roller Bearings.
　　　　　　   
1N=0.102kgf=0.2248lbs.
J7 1mm=0.03937inch
J8
Table 8 Tolerances and allowable values of Super Slim Type Crossed Roller Bearings unit: μ m Table 10.2 Tolerances and allowable values of outer rings of Mounting Holed Type High Rigidity Crossed Roller Bearings (V) unit: μ m
d ∆ dmp ∆ Dmp ∆ Bs and ∆ Cs Kia and Sia Kea and Sea D ∆ Dmp ∆ Cs
Single plane mean bore dia. Single plane mean outside dia. Deviations of a single inner ring width
Kea Sea
Nominal bore Radial and axial run-out Radial and axial run-out Nominal
outside Single plane mean outside dia. deviation Deviation of Radial run-out of assembled Assembled bearing outer ring
diameter deviation deviation and outer ring width of assembled bearing of assembled bearing diameter a single outer bearing outer ring face run-out with raceway
mm High Low High Low High Low inner ring outer ring mm Class 0
P6 P5 P4, P2 ring width Class P6
RP6-2 P5 P4 P2 Class P6 P5 P4 P2
20 0 − 10 0 − 11 0 − 75 13 20 Over Incl. High Low High Low High Low High Low High Low 0 RP6 RP5 RP4 RP2 0 RP6 RP5 RP4 RP2
30 0 − 10 0 − 11 0 − 75 13 20
50 60 0 − 13 0 − 11 0 − 9 0 − 7 0 − 75 20 10 7 5 2.5 20 10 7 5 2.5
40 0 − 12 0 − 13 0 − 75 15 25
60 80 0 − 13 0 − 11 0 − 9 0 − 7 0 − 75 25 13 8 5 4 25 13 8 5 4
50 0 − 12 0 − 13 0 − 75 15 25
80 95 0 − 15 0 − 13 0 − 10 0 − 8 0 − 75 25 13 8 5 4 25 13 8 5 4
95 120 0 − 15 0 − 13 0 − 10 0 − 8 0 − 75 35 18 10 6 5 35 18 10 6 5
120 140 0 − 18 0 − 15 0 − 11 0 − 9 0 − 75 35 18 10 6 5 35 18 10 6 5
140 150 0 − 18 0 − 15 0 − 11 0 − 9 0 − 75 40 20 11 7 5 40 20 11 7 5
150 165 0 − 25 0 − 18 0 − 13 0 − 10 0 − 75 40 20 11 7 5 40 20 11 7 5
165 180 0 − 25 0 − 18 0 − 13 0 − 10 0 − 75 45 23 13 8 5 45 23 13 8 5
180 210 0 − 30 0 − 20 0 − 15 0 − 11 0 − 75 45 23 13 8 5 45 23 13 8 5
Table 9 Tolerances and allowable values of Slim Type Crossed Roller Bearings unit: μ m
210 240 0 − 30 0 − 20 0 − 15 0 − 11 0 − 75 50 25 15 10 7 50 25 15 10 7
d ∆ dmp ∆ Dmp ∆ Bs and ∆ Cs Kia and Sia Kea and Sea
Nominal bore Single plane mean bore dia. Single plane mean outside dia. Deviations of a single inner ring width Radial and axial run-out Radial and axial run-out
diameter deviation deviation and outer ring width of assembled bearing of assembled bearing
mm High Low High Low High Low inner ring outer ring
■ Clearance
50 0 − 15 0 − 13 0 − 127 13 13
60 0 − 15 0 − 13 0 − 127 13 13 The radial internal clearances of Crossed Roller Table 11.2 Radial internal clearances for Super Slim
70 0 − 15 0 − 15 0 − 127 15 15 Bearings, Super Slim Type Crossed Roller Bearings, Type Crossed Roller Bearings unit: μ m
80 0 − 20 0 − 15 0 − 127 15 15 Slim Type Crossed Roller Bearings and Mounting d Radial internal clearance
90 0 − 20 0 − 15 0 − 127 15 15 Holed Type High Rigidity Crossed Roller Bearings (V) Nominal bore diameter
C1
100 0 − 20 0 − 15 0 − 127 15 15 are shown below in Table 11.1-11.4. of bearing
110 0 − 20 0 − 20 0 − 127 20 20 mm Min. Max.
120 0 − 25 0 − 20 0 − 127 20 20 20 0 15
Table 11.1 Radial internal clearances unit: μ m
130 0 − 25 0 − 25 0 − 127 25 25 30 0 15
140 0 − 25 0 − 25 0 − 127 25 25 d Radial internal clearance
Nominal bore diameter 40 0 15
150 0 − 25 0 − 25 0 − 127 25 25
mm T1 C1 C2 50 0 15
160 0 − 25 0 − 25 0 − 127 25 25
Over Incl. Min. Max. Min. Max. Min. Max.
170 0 − 25 0 − 30 0 − 127 25 25
180 0 − 30 0 − 30 0 − 127 30 30 − 30 − 10 0 0 10 10 20 Table 11.3 Radial internal clearances of Slim
190 0 − 30 0 − 30 0 − 127 30 30 30 40 − 10 0 0 10 10 20 Type Crossed Roller Bearings unit: μ m
200 0 − 30 0 − 30 0 − 127 30 30 40 50 − 10 0 0 10 10 25
Radial internal clearance
50 65 − 10 0 0 10 10 25 d
Nominal bore diameter T1 C1 Normal
65 80 − 10 0 0 15 15 30
mm
80 100 − 10 0 0 15 15 35 Min. Max. Min. Max. Min. Max.
100
120
120
140
− 15
− 15
0
0
0
0
15
20
15
20
35
45
50
60
−   8
−   8
0
0
0
0
15
15
30
30
56
56
J
140 160 − 15 0 0 20 20 50 70 −   8 0 0 15 30 56
Table 10.1 Tolerances and allowable values of inner rings of Mounting Holed Type High Rigidity Crossed Roller Bearings (V) unit: μ m 160 200 − 15 0 0 20 20 50 80 −   8 0 0 15 41 66
200 250 − 20 0 0 25 25 60 90 −   8 0 0 15 41 66
d ∆ dmp ∆ Bs Kia Sia
Deviation of
250 315 − 20 0 0 25 25 60 100 −   8 0 0 15 41 66
Nominal bore Single plane mean bore dia. deviation Radial run-out of assembled Assembled bearing inner ring
diameter a single inner bearing inner ring face run-out with raceway 315 400 − 25 0 0 30 30 70 110 −   8 0 0 15 41 66
mm Class 0
P6 P5 P4, P2 ring width
Class P6 P5 P4 P2 Class P6 P5 P4 P2 400 500 − 30 0 0 40 40 85 120 −   8 0 0 15 51 76
RP6-2
Over Incl. High Low High Low High Low High Low High Low 0 RP6 RP5 RP4 RP2 0 RP6 RP5 RP4 RP2 500 630 − 30 0 0 50 50 100 130 −   8 0 0 15 51 76
630 710 − 30 0 0 60 60 120 140 −   8 0 0 15 51 76
− 20 0 − 10 0 − 8 0 − 6 0 − 5 0 − 75 13 8 4 3 2.5 13 8 4 3 2.5
710 800 − 40 0 0 70 70 140 150 −   8 0 0 15 51 76
20 30 0 − 10 0 − 8 0 − 6 0 − 5 0 − 75 15 10 5 4 2.5 15 10 5 4 2.5
30 35 0 − 12 0 − 10 0 − 8 0 − 6 0 − 75 15 10 5 4 2.5 15 10 5 4 2.5 Remark　 This table is not applicable to Super Slim Type Crossed 160 − 10 0 0 20 51 76
Roller Bearings, Slim Type Crossed Roller Bearings and
35 50 0 − 12 0 − 10 0 − 8 0 − 6 0 − 75 20 10 5 4 2.5 20 10 5 4 2.5 Mounting Holed Type High Rigidity Crossed Roller 170 − 10 0 0 20 51 76
50 65 0 − 15 0 − 12 0 − 9 0 − 7 0 − 75 20 10 5 4 2.5 20 10 5 4 2.5 Bearings (V). 180 − 10 0 0 20 61 86
65 80 0 − 15 0 − 12 0 − 9 0 − 7 0 − 75 25 13 6 5 2.5 25 13 6 5 2.5 190 − 10 0 0 20 61 86
80 100 0 − 20 0 − 15 0 − 10 0 − 8 0 − 75 25 13 6 5 2.5 25 13 6 5 2.5 200 − 10 0 0 20 61 86
100 120 0 − 20 0 − 15 0 − 10 0 − 8 0 − 75 30 18 8 6 2.5 30 18 8 6 2.5

1N=0.102kgf=0.2248lbs.
J9 1mm=0.03937inch
J10
Table 11.4 Radial internal clearances of Mounting Holed
Type High Rigidity Crossed Roller Bearings (V)
■ Fit ■ Allowable rotational speed When using a special grease, carefully examine the
grease properties and contents such as base oil vis-
unit: μ m The standard fits of Crossed Roller Bearings are shown Allowable rotational speeds of Crossed Roller cosity and extreme pressure additives. In this case,
d Radial internal clearance in Table 12.1, and recommended fits for Slim Type Bearings are affected by mounting and operating con- please contact .
Nominal bore diameter Crossed Roller Bearings with normal clearances are ditions. The values in general operation are shown in
mm T1 C1 C2
shown in Table 12.2. For Super Slim Type Crossed Table 13. Table 14 Bearings with prepacked grease
Over Incl. Min. Max. Min. Max. Min. Max.
Roller Bearings, it is recommended to use a slight inter- ○：With prepacked grease 　　×：Without prepacked grease
− 20 − 10 0 0 10 10 20 ference fit adjusted to the actual measured dimensions. Table 13 dmn （1）of
values Crossed Roller Bearings Seal specification
20 25 − 10 0 0 10 10 20 For large bearings, fit based on the actual measured Lubricant Model code Sealed type One side
25 35 − 10 0 0 10 10 25 Open type
dimensions of the bearings is recommended, and fit Grease Oil sealed type
35 65 − 10 0 0 15 15 30 Type (No symbol) (UU) (U)
allowance should be chosen as small as possible in
65 80 − 10 0 0 15 15 35 accordance with the tolerance class given in Table With cage or Open type 75 000 150 000 CRBH(V) … A × 〇 −
80 95 − 15 0 0 15 15 35 12.1. When complex loads or shock loads are applied with separator Sealed type 60 000 − CRBC × 〇 ×
95 110 − 15 0 0 20 20 45 or when high rotational accuracy and rigidity of the Open type 50 000 75 000 CRB × 〇 ×
110 125 − 15 0 0 20 20 50 bearing are required, it is recommended to use a slight Full complement
Sealed type 40 000 − CRBT … A 〇 − −
interference fit adjusted to the actual measured dimen-
Note(1)　・d m n value ＝ d m × n　
sions for both inner and outer rings. CRBS × − −
　　　　　where, 　dm    : Mean value of bearing bore and outside diameters,  mm
For the interference fit, the radial internal clearance 　　　　　　　　　 n   : Number of rotations per minute,  min-1 CRBS … A − 〇 ×
after the fit decreases by approximately 70% to 90%
of the interference amount. To avoid excessive pre- CRBS … V × 〇 ×
load due to fit, it is recommended to use a slight inter-
ference fit adjusted to the actual measured dimen-
■ Rotational torque CRBF(V) … A × 〇 −

Rotational torque of Crossed Roller Bearings

■ Oil Hole
sions for both T1 and C1 clearances.
are lower than that of plain bearings and the differ-
Table 12.1 Recommended fits for Crossed Roller Bearings under normal load ence between the static torque and the dynamic
For Crossed Roller Bearings, oil holes and oil grooves can be
(kinetic) torque is small. Therefore, these bearings
Tolerance class provided on bearing rings if requested. Not applicable to the
minimize power consumption and operating tempera-
Radial internal clearance Inner ring rotating load Outer ring rotating load Super Slim Type. When an oil hole is required on the outer ring,
ture rise of machinery and increase the overall effi-
Shaft Housing bore Shaft Housing bore attach "-OH" before the clearance symbol in the identification
ciency of machines.
number. When an oil hole and an oil groove are required on the
C1 clearance h5 H7 g5 J7（1） The rotational torque is affected by many factors, but
outer ring, attach "-OG" at the same place in the identification
C2 clearance j5 H7 g5 J7（1） the following equations can be used expediently.
number. For an oil hole on the inner ring, attach "/OH", and for
Note(1)　It is recommended that a slight interference fit adjusted to the actual measured dimensions of the bearing is used. Dpw
T ＝ μP0r——— an oil hole and an oil groove on the inner ring, attach "/OG", at
2 the same place in the identification number. High Rigidity Type
Table 12.2 Recommended fits for Slim Type Crossed Roller Bearings with normal clearances where, T ： Rotational torque,　N・mm
Crossed Roller Bearings (V) and Mounting Holed Type High
(Dimensional tolerances of shaft and housing bore) unit: μ m μ ： Friction coefficient (Approx. 0.010)
Rigidity Type Crossed Roller Bearings (V) have an oil groove
Inner ring rotating load Outer ring rotating load P0r ： Static equivalent radial load,　N
d and two oil holes on the outer ring as standard. Table 15 shows
Dpw ： Pitch circle diameter,　mm
J
Nominal bore diameter Shaft Housing bore Shaft Housing bore availability of oil holes for each bearing type.
d＋D
（  ）
mm High Low High Low High Low High Low Dpw ≒————
2
50 ＋ 15 0 ＋ 13 0 − 15 − 30 − 13 − 25 Table 15 Oil holes
60 ＋ 15 0 ＋ 13 0 − 15 − 30 − 13 − 25
■ Lubrication
Oil hole code
70 ＋ 15 0 ＋ 15 0 − 15 − 30 − 15 − 30 Bearing type
/nOH /nOG -nOH -nOG
80 ＋ 20 0 ＋ 15 0 − 20 − 40 − 15 − 30
These bearings are generally lubricated with grease. CRBH(V) … A 〇 〇 − −（1）
90 ＋ 20 0 ＋ 15 0 − 20 − 40 − 15 − 30
Grease is supplied through the clearance between the CRBC 〇 〇 〇 〇
100 ＋ 20 0 ＋ 15 0 − 20 − 40 − 15 − 30
inner ring and the outer ring. CRB 〇 〇 〇 〇
110 ＋ 20 0 ＋ 20 0 − 20 − 40 − 20 − 40
Grease specification is shown in Table 14, ALVANIA CRBT … A − − − −
120 ＋ 25 0 ＋ 20 0 − 25 − 50 − 20 − 40
GREASE EP2 (SHOWA SHELL SEKIYU K.K) is CRBS 〇 − 〇 −
130 ＋ 25 0 ＋ 25 0 − 25 − 50 − 25 − 50
prepacked as the lubricating grease. CRBS … A 〇 − 〇 −
140 ＋ 25 0 ＋ 25 0 − 25 − 50 − 25 − 50
For bearings without prepacked grease, supply grease CRBS … V 〇 − 〇 −
150 ＋ 25 0 ＋ 25 0 − 25 − 50 − 25 − 50
or oil for use. Operating without grease or oil will increase CRBF(V) … A − − − −（1）
160 ＋ 25 0 ＋ 25 0 − 25 − 50 − 25 − 50
the wear of the rolling contact surfaces and cause a short Notes(1)　CRBH(V) … A and CRBF(V) … A are provided with an oil
170 ＋ 25 0 ＋ 30 0 − 25 − 50 − 30 − 60 groove and two oil holes on the outer ring.
180 ＋ 30 0 ＋ 30 0 − 30 − 60 − 30 − 60 bearing life. Remark　 n denotes the number of oil holes not exceeding 4. For
one oil hole, number is not indicated.
190 ＋ 30 0 ＋ 30 0 − 30 − 60 − 30 − 60
When preparing multiple oil holes, please contact .
200 ＋ 30 0 ＋ 30 0 − 30 − 60 − 30 − 60

1N=0.102kgf=0.2248lbs.
J11 1mm=0.03937inch
J12
 Example 1　 When the inner ring has 4 oil holes
plates should be determined to get a secure fixing
while considering the dimension of bearing width ■ Tightening torque of mounting bolts B
A
　　　C R B C    1 0 020   /   4O H  C1
which is given a minus tolerance. (See Fig.2) The standard tightening torque values for Mounting
　　　　　　　　　　　　　　　　　4 Oil holes ●2 The depth of the housing bore is recommended to Holed Type High Rigidity Crossed Roller Bearings (V)
　　　　　　　　　　　　　　　　　In inner ring be equal to or larger than the bearing width. m o u n t i n g b o l t s a r e s h ow n i n Ta bl e 1 6 . W h e n
●3 Separation prevention bolts for the outer ring of

PC
machines or equipment are subjected to severe vibra-

D1
O
Example 2　 When the outer ring has a single oil hole Standard Type Crossed Roller Bearings are provided tion, shock, large fluctuating load, or moment load, the

D2
　　　C R B C    1 0 020   -    O H  C1 to prevent separation of two halves of the outer ring bolts should be tightened with a torque 1.2 to 1.5

PC
during transportation or mounting. When mounting, times higher than the standard torque values shown.
　　　　　　　　　　　　　　　　　1 Oil hole they should be loosened slightly. If the mating member material is cast iron or alumi-
　　　　　　　　　　　　　　　　　In outer ring
●4 High Rigidity Type Crossed Roller Bearings (V), num, reduce the tightening torque depending on the Rc1/8
Super Slim Type Crossed Roller Bearings and Slim strength characteristics of the mating member materi- A'
(Oil hole)

■ Operating Temperature Range

Type Crossed Roller Bearings have a plug for hole for al. A-O-A'
inserting rollers. When mounting the bearings, locate Please do not tighten with too much torque as abnor- Fig. 5 Manufacturing example
The operating temperature range for Crossed Roller the plug at a position that is not included in the maxi- mal frictional torque or short life may occur.
Bearings is − 20℃〜＋ 120℃ . However, the maxi- mum loading zone. The plug location can be found by
the pin pressed at the side of the outer ring. Table 17 Example of manufacturing dimensions
mum allowable temperature for types with separator
Table 16 Tightening torque of mounting bolts Basic dynamic Basic static
and with seal is ＋ 110℃ , and ＋ 100℃ when they are Boundary dimensions
load rating load rating
continuously operated. 2. Mounting Holed Type High Rigidity Bolt size
Tightening mm
C
N ・m C0
torque
Crossed Roller Bearings (V) d D B r min PCD1 PCD2 N N

■ Mounting M3 × 0.5
M4 × 0.7
1.7
4.0
160 295 35 2 184 270 60 300 167 000
210 380 40 2.5 240 350 108 000 313 000
When the rigidity of the mounting parts is not suffi-
M5 × 0.8 7.9 350 540 50 2.5 385 505 235 000 725 000
cient, stress concentration will occur at the contact
M8 × 1.25 32
area between the rollers and raceways, and the bear-
Above values are for Carbon steel bolt (Strength division 12.9)
ing performance will be deteriorated significantly. Structure of Double-acting Angular Roller Bearing
Therefore, it is necessary to carefully examine the
rigidity of housing and the strength of fixing bolts
when a large moment will be applied.
■ Double Row Angular Contact Roller Bearing
The shoulder height diameters (da and Da) that are We manufacture Double Row Angular Contact Roller
Fig.3 Example of direct mounting to the mating surface of Mounting Bearings to order.
related to mounting should certainly satisfy the values
Holed Type High Rigidity Crossed Roller Bearings (V)
shown in the dimension tables. When these dimen- If needed, please contact .
sions are incorrect, deformations of inner and outer ●
1 Mounting Holed Type High Rigidity Crossed Roller Double Row Angular Contact Roller Bearings have a
rings will occur and the bearing performance will be Bearings (V) can be mounted directly to the mounting large number of cylindrical rollers with a large contact
deteriorated remarkably. surface by fixing bolts. (See Fig. 3) area with a raceway and an excellent load capability,
between the inner and outer rings arranged in a dou-
ble row of raceways. This underpins even higher rigidi-
1. Other than Mounting Holed Type High
Rigidity Crossed Roller Bearings (V)
ty and lower torque than High Rigidity Type Crossed
Roller Bearings (V).
J
The mounting holes in both inner and outer rings facil-
itate installation to your machines and equipment.
Further, the integrated structure (non split) construct-
ed in both inner and outer rings can avoid installation
errors, yielding extra-high-rigidity and high-accuracy
guiding performance without being affected by other Outer ring
Fig.4 Example of mounting to the housing of Mounting peripheral structures such as housing or pressure
Holed Type High Rigidity Crossed Roller Bearings (V) plate. Cylindrical
roller
●
2 If large number of radial load and/or moment is
expected, it is recommended to prepare flange part.
Separator
Fig. 2 Mounting example (See Fig.4)
●3 Mounting Holed Type High Rigidity Crossed Roller
Inner ring
Bearings (V) have a plug for hole for inserting cylindri-
●
1 The inner and outer rings should be securely fixed
in the axial direction by using fixing plates, etc. cal rollers. When mounting the bearings, locate the
Recommended thickness of the fixing plate is 1/2 or plug at a position that is not included in the maximum
more of the bearing width B. The dimensions in the loading zone. The plug location can be found by the
axial direction of the housing bore and the fixing pin pressed at the side of the outer ring.

J13 J14
 CROSSED ROLLER BEARINGS
High Rigidity Type Crossed Roller Bearings (V) Open Type/With Separator
Sealed Type/With Separator

Shaft dia. 20 − 300mm CRBH(V) … A CRBH(V) … AUU

Identification number Mass Boundary dimensions  mm Mounting Basic dynamic Basic static
Shaft (Ref.) dimensions  mm load rating load rating
High Rigidity Type Crossed Roller Bearings (V)
dia.
(1) C C0
mm
Open Type Seald Type
kg
d D B r min da Da
N N

20 CRBH 208 A CRBH 208 A UU 0.04 20 36 8 0.3 24 31 2 910 2 430

25 CRBH 258 A CRBH 258 A UU 0.05 25 41 8 0.3 29 36 3 120 2 810
30 CRBHV 3010 A CRBHV 3010 A UU 0.12 30 55 10 0.3 36.5 48.5 7 600 8 370
35 CRBHV 3510 A CRBHV 3510 A UU 0.13 35 60 10 0.3 41.5 53.5 7 900 9 130
40 CRBHV 4010 A CRBHV 4010 A UU 0.15 40 65 10 0.3 46.5 58.5 8 610 10 600
45 CRBHV 4510 A CRBHV 4510 A UU 0.16 45 70 10 0.3 51.5 63.5 8 860 11 300
50 CRBHV 5013 A CRBHV 5013 A UU 0.29 50 80 13 0.6 56 74 17 300 20 900
60 CRBHV 6013 A CRBHV 6013 A UU 0.33 60 90 13 0.6 66 84 18 800 24 300
70 CRBHV 7013 A CRBHV 7013 A UU 0.38 70 100 13 0.6 76 94 20 100 27 700
80 CRBHV 8016 A CRBHV 8016 A UU 0.74 80 120 16 0.6 88 112 32 100 43 400
90 CRBHV 9016 A CRBHV 9016 A UU 0.81 90 130 16 0.6 98 122 33 100 46 800
100 CRBHV 10020 A CRBHV 10020 A UU 1.45 100 150 20 0.6 110 140 50 900 72 200 J
110 CRBHV 11020 A CRBHV 11020 A UU 1.56 110 160 20 0.6 120 150 52 400 77 400
120 CRBHV 12025 A CRBHV 12025 A UU 2.62 120 180 25 1 132 168 73 400 108 000
130 CRBHV 13025 A CRBHV 13025 A UU 2.82 130 190 25 1 142 178 75 900 115 000
140 CRBHV 14025 A CRBHV 14025 A UU 2.96 140 200 25 1 152 188 81 900 130 000
150 CRBHV 15025 A CRBHV 15025 A UU 3.16 150 210 25 1 162 198 84 300 138 000
200 CRBHV 20025 A CRBHV 20025 A UU 4.0 200 260 25 1 212 248 92 300 169 000
250 CRBHV 25025 A CRBHV 25025 A UU 4.97 250 310 25 1.5 262 298 102 000 207 000
300 CRBH 30025 A CRBH 30025 UU 5.29 300 360 25 1.5 312 348 112 000 245 000

Note(1)　　 Minimum allowable single value of chamfer dimension r

Remarks1.   The outer ring has an oil groove and two oil holes.
2.   No grease is prepacked for Open Type. Perform proper lubrication. Grease is prepacked for Sealed Type.
3.   If one side sealed type are needed, please contact .

1N=0.102kgf=0.2248lbs.
J15 1mm=0.03937inch
J16
 CROSSED ROLLER BEARINGS
Standard Type Crossed Roller Bearings
Open Type/With Cage Open Type/Full Complement Type
Sealed Type/With Cage Sealed Type/Full Complement Type

Shaft dia. 30 − 200mm CRBC CRBC … UU CRB CRB … UU

Identification number Mass Boundary dimensions Mounting CRBC   CRB

Shaft With Cage Full complement (Ref.) mm dimensions mm Basic dynamic Basic static Basic dynamic Basic static
dia. load rating load rating load rating load rating
(1)
Open Type Seald Type Open Type Seald Type
d D B r min da Da C C0 C C0
mm kg N N N N

30 CRBC 3010 CRBC 3010 UU CRB 3010 CRB 3010 UU 0.12 30 55 10 0.3 34 44 3 830 4 130 5 290 6 350
40 CRBC 4010 CRBC 4010 UU CRB 4010 CRB 4010 UU 0.15 40 65 10 0.3 44 54 4 280 5 140 5 980 8 040
50 CRBC 5013 CRBC 5013 UU CRB 5013 CRB 5013 UU 0.29 50 80 13 0.6 55 71 10 700 12 600 14 200 18 400
60 CRBC 6013 CRBC 6013 UU CRB 6013 CRB 6013 UU 0.33 60 90 13 0.6 64 81 11 600 14 600 15 400 21 500
70 CRBC 7013 CRBC 7013 UU CRB 7013 CRB 7013 UU 0.38 70 100 13 0.6 75 91 12 300 16 700 17 000 25 500
80 CRBC 8016 CRBC 8016 UU CRB 8016 CRB 8016 UU 0.74 80 120 16 0.6 86 107 18 200 25 500 24 300 37 500
90 CRBC 9016 CRBC 9016 UU CRB 9016 CRB 9016 UU 0.81 90 130 16 1 98 118 19 400 28 600 25 900 42 100
100 CRBC 10020 CRBC 10020 UU CRB 10020 CRB 10020 UU 1.45 100 150 20 1 108 134 31 500 45 100 39 400 61 100
110 CRBC 11020 CRBC 11020 UU CRB 11020 CRB 11020 UU 1.56 110 160 20 1 118 144 33 500 50 700 41 200 66 700
120 CRBC 12025 CRBC 12025 UU CRB 12025 CRB 12025 UU 2.62 120 180 25 1.5 132 164 47 700 70 500 59 900 95 400
130 CRBC 13025 CRBC 13025 UU CRB 13025 CRB 13025 UU 2.82 130 190 25 1.5 140 172 49 200 74 800 61 000 99 800
140 CRBC 14025 CRBC 14025 UU CRB 14025 CRB 14025 UU 2.96 140 200 25 1.5 151 183 50 700 79 200 64 100 108 000 J
CRBC 15025 CRBC 15025 UU CRB 15025 CRB 15025 UU 3.16 150 210 25 1.5 160 192 53 800 87 700 65 000 113 000
150
CRBC 15030 CRBC 15030 UU CRB 15030 CRB 15030 UU 5.3 150 230 30 1.5 166 202 69 200 108 000 85 900 144 000
CRBC 20025 CRBC 20025 UU CRB 20025 CRB 20025 UU 4.0 200 260 25 2 208 239 60 200 110 000 75 300 148 000
200 CRBC 20030 ─ CRB 20030 ─ 6.7 200 280 30 2 218 262 108 000 178 000 133 000 234 000
CRBC 20035 ─ CRB 20035 ─ 9.58 200 295 35 2 221 274 137 000 215 000 168 000 282 000

Note(1)　　 Minimum allowable single value of chamfer dimension r

Remarks1.   No oil hole is provided.
2.   No grease is prepacked for Open Type. Perform proper lubrication. Grease is prepacked for Sealed Type.

1N=0.102kgf=0.2248lbs.
J17 1mm=0.03937inch
J18
 CROSSED ROLLER BEARINGS
Standard Type Crossed Roller Bearings
Open Type/With Cage Open Type/Full Complement Type
Sealed Type/With Cage Sealed Type/Full Complement Type

Shaft dia. 250 − 800mm CRBC 25025

CRBC 30025
CRBC 25025UU
CRBC 30025UU
CRB 25025
CRB 30025
CRB 25025UU
CRB 30025UU
CRBC CRB

Identification number Mass Boundary dimensions Mounting CRBC   CRB

Shaft (Ref.) mm dimensions mm Basic dynamic Basic static Basic dynamic Basic static
dia. With Cage Full complement
load rating load rating load rating load rating
(1)
Open Type Seald Type Open Type Seald Type
d D B r min da Da C C0 C C0
mm kg N N N N

CRBC 25025 CRBC 25025 UU CRB 25025 CRB 25025 UU 4.97 250 310 25 2.5 259 290 67 200 136 000 83 900 183 000
250 CRBC 25030 ─ CRB 25030 ─ 8.1 250 330 30 2.5 265 310 116 000 208 000 146 000 283 000
CRBC 25040 ─ CRB 25040 ─ 14.8 250 355 40 2.5 271 330 179 000 299 000 215 000 382 000
CRBC 30025 CRBC 30025 UU CRB 30025 CRB 30025 UU 5.88 300 360 25 2.5 310 341 73 800 162 000 91 900 217 000
300 CRBC 30035 ─ CRB 30035 ─ 13.4 300 395 35 2.5 318 372 163 000 299 000 205 000 408 000
CRBC 30040 ─ CRB 30040 ─ 17.2 300 405 40 2.5 321 381 194 000 351 000 235 000 451 000
CRBC 40035 ─ CRB 40035 ─ 14.5 400 480 35 2.5 414 457 133 000 300 000 165 000 400 000
400 CRBC 40040 ─ CRB 40040 ─ 23.5 400 510 40 2.5 423 483 222 000 455 000 270 000 590 000
CRBC 40070 ─ CRB 40070 ─ 72.4 400 580 70 2.5 430 532 470 000 811 000 576 000 1 060 000
CRBC 50040 ─ CRB 50040 ─ 26.0 500 600 40 2.5 517 573 212 000 497 000 259 000 648 000
500 CRBC 50050 ─ CRB 50050 ─ 41.7 500 625 50 2.5 531 592 247 000 561 000 306 000 747 000
CRBC 50070 ─ CRB 50070 ─ 86.1 500 680 70 2.5 530 633 536 000 1 020 000 653 000 1 330 000
CRBC 60040 ─ CRB 60040 ─ 30.6 600 700 40 3 621 676 231 000 581 000 287 000 774 000
─ ─
600 CRBC 60070
CRBC 600120 ─
CRB 60070
CRB 600120 ─
102
274
600
600
780 70
870 120
3
3
630 734 591 000 1 230 000 700 000 1 540 000
643 817 1 250 000 2 210 000 1 490 000 2 800 000 J
CRBC 70045 ─ CRB 70045 ─ 46.5 700 815 45 3 730 785 250 000 681 000 313 000 917 000
700 CRBC 70070 ─ CRB 70070 ─ 115 700 880 70 3 731 834 630 000 1 390 000 766 000 1 810 000
CRBC 700150 ─ CRB 700150 ─ 478 700 1 020 150 3 751 953 1 660 000 3 010 000 1 980 000 3 820 000
CRBC 80070 ─ CRB 80070 ─ 109 800 950 70 4 831 907 417 000 1 090 000 513 000 1 440 000
800 ─ ─
CRBC 800100 CRB 800100 247 800 1 030 100 4 840 972 936 000 2 040 000 1 140 000 2 640 000

Note(1)　　 Minimum allowable single value of chamfer dimension r

Remarks1.   No oil hole is provided.
2.   No grease is prepacked for Open Type. Perform proper lubrication. Grease is prepacked for Sealed Type.

1N=0.102kgf=0.2248lbs.
J19 1mm=0.03937inch
J20
 CROSSED ROLLER BEARINGS
Super Slim Type Crossed Roller Bearings Open Type/With Separator

Shaft dia. 20 − 50mm CRBT … A

Identification number Mass Boundary dimensions Mounting Basic dynamic Basic static
Shaft (Ref.) mm dimensions mm load rating load rating
dia.
(1) C C0
mm g d D B r min da Da
N N

20 CRBT 205 A 14.8 20 31 5 0.15 22.5 27 1 400 1 290

30 CRBT 305 A 20.7 30 41 5 0.15 32.5 37 1 770 1 970
40 CRBT 405 A 26.5 40 51 5 0.15 42.5 47 2 000 2 520
50 CRBT 505 A 32.3 50 61 5 0.15 52.5 57 2 280 3 200

Note(1)　　 Minimum allowable single value of chamfer dimension r .

Remarks1.   No oil hole is provided.
2.   Grease is prepacked.

1N=0.102kgf=0.2248lbs.
J21 1mm=0.03937inch
J22
 CROSSED ROLLER BEARINGS
Slim Type Crossed Roller Bearings
Open Type/With Cage Open Type/Full Complement Type
Sealed Type/With Separator Sealed Type/Full Complement Type

Shaft dia. 50 − 200mm CRBS CRBS … AUU

… VUU
CRBS … V

Identification number Mass Boundary dimensions Mounting CRBS(2) CRBS…AUU(3) CRBS…V(2)

Shaft CRBS…VUU(3)
(Ref.) mm dimensions mm With cage With Separator Full complement
dia. With Cage With Separator Full complement
(1) Basic dynamic load rating Basic static load rating Basic dynamic load rating Basic static load rating Basic dynamic load rating Basic static load rating
Open Type Seald Type Open Type Seald Type
d D B r min da Da C C0 C C0 C C0
mm g N N N N N N

50 CRBS 508 CRBS 508 A UU CRBS 508 V CRBS 508 V UU 84 50 66 8 0.4 54 61 4 900 6 170 4 680 5 810 6 930 9 800
60 CRBS 608 CRBS 608 A UU CRBS 608 V CRBS 608 V UU 94 60 76 8 0.4 64 71 5 350 7 310 5 350 7 310 7 600 11 700
70 CRBS 708 CRBS 708 A UU CRBS 708 V CRBS 708 V UU 108 70 86 8 0.4 74 81 5 740 8 440 5 740 8 440 8 190 13 600
80 CRBS 808 CRBS 808 A UU CRBS 808 V CRBS 808 V UU 122 80 96 8 0.4 84 91 6 130 9 590 6 130 9 590 8 790 15 500
90 CRBS 908 CRBS 908 A UU CRBS 908 V CRBS 908 V UU 135 90 106 8 0.4 94 101 6 490 10 700 6 490 10 700 9 310 17 400
100 CRBS 1008 CRBS 1008 A UU CRBS 1008 V CRBS 1008 V UU 152 100 116 8 0.4 104 111 6 850 11 900 6 530 11 100 9 850 19 300
110 CRBS 1108 CRBS 1108 A UU CRBS 1108 V CRBS 1108 V UU 163 110 126 8 0.4 114 121 7 160 13 000 6 850 12 300 10 300 21 200
120 CRBS 1208 CRBS 1208 A UU CRBS 1208 V CRBS 1208 V UU 184 120 136 8 0.4 124 131 7 530 14 100 7 070 13 000 10 900 23 000
130 CRBS 1308 CRBS 1308 A UU CRBS 1308 V CRBS 1308 V UU 199 130 146 8 0.4 134 141 7 860 15 300 7 270 13 800 11 200 24 600
140 CRBS 1408 CRBS 1408 A UU CRBS 1408 V CRBS 1408 V UU 205 140 156 8 0.4 144 151 8 060 16 400 7 510 14 900 11 700 26 800
150 CRBS 1508 CRBS 1508 A UU CRBS 1508 V CRBS 1508 V UU 220 150 166 8 0.4 154 161 8 350 17 500 7 810 16 000 12 100 28 700
160 CRBS 16013 CRBS 16013 A UU CRBS 16013 V CRBS 16013 V UU 620 160 186 13 0.6 166 179 20 300 39 900 19 400 37 700 26 900 58 200 J
170 CRBS 17013 CRBS 17013 A UU CRBS 17013 V CRBS 17013 V UU 675 170 196 13 0.6 176 189 20 900 42 200 20 000 39 900 27 800 61 600
180 CRBS 18013 CRBS 18013 A UU CRBS 18013 V CRBS 18013 V UU 710 180 206 13 0.6 186 199 21 500 44 600 21 900 45 700 28 600 65 200
190 CRBS 19013 CRBS 19013 A UU CRBS 19013 V CRBS 19013 V UU 740 190 216 13 0.6 196 209 22 100 46 900 22 900 49 200 29 300 68 600
200 CRBS 20013 CRBS 20013 A UU CRBS 20013 V CRBS 20013 V UU 780 200 226 13 0.6 206 219 22 500 49 300 23 300 51 600 30 000 72 200

Note(1)　　 Minimum allowable single value of chamfer dimension r

(2)　　 No grease is prepacked. Perform proper lubrication.
(3)　　 Grease is prepacked.
Remark No oil hole is provided.

1N=0.102kgf=0.2248lbs.
J23 1mm=0.03937inch
J24
 CROSSED ROLLER BEARINGS
Mounting Holed Type High Rigidity Open Type/With Separator
Crossed Roller Bearings (V) Sealed Type/With Separator

Shaft dia. 10 − 115mm

CRBF(V) … AT CRBF(V) … ATUU CRBFV … A CRBFV … AUU CRBFV … AD CRBFV … ADUU
Identification number Mass Boundary dimensions Mounting holes mm Mounting Basic dynamic Basic static
Shaft (Ref.) mm dimensions load rating load rating
Mounting Holed Type High Rigidity Crossed Roller Bearing(V)  mm
dia.
(1) (1) Inner ring Outer ring C C0
Open Type Sealed Type d D B r 1min r 2min Mounting holes Mounting holes da Da
mm kg PCD1 PCD2 N N
6-φ3.4 through
10 CRBF 108 AT CRBF 108 AT UU 0.12 10 52 8 0.3 0.3 16 4-M3 through 42 24 31 2 910 2 430
φ6.5 counter bore depth 3.3
6-φ3.4 through
20 CRBFV 2012 AT CRBFV 2012 AT UU 0.31 20 70 12 0.3 0.3 28 6-M3 through 57 36.5 48.5 7 600 8 370
φ6.5 counter bore depth 3.3

35 67 6-φ3.4 through 46.5 58.5 8 610 10 600

25 CRBFV 2512 AT CRBFV 2512 AT UU 0.40 25 80 12 0.6 0.6 6-M3 through
φ6.5 counter bore depth 3.3

45 83 8-φ4.5 through 56 74 17 300 20 900

35 CRBFV 3515 AT CRBFV 3515 AT UU 0.66 35 95 15 0.6 0.6 8-M4 through
φ8 counter bore depth 4.4

65 105 8-φ5.5 through 76 94 20 100 27 700

55 CRBFV 5515 AT CRBFV 5515 AT UU 0.96 55 120 15 0.6 0.6 8-M5 through
φ9.5 counter bore depth 5.4

CRBFV 8022 AT CRBFV 8022 AT UU 2.63 10-M5 through

10-φ5.5 through
80 CRBFV 8022 A CRBFV 8022 A UU 80 165 22 0.6 1 97 10- φ 5.5 through 148 φ9.5 counter bore 107 137 51 100 72 000
φ 9.5 counter bore
J
2.60 depth 5.4
CRBFV 8022 AD CRBFV 8022 AD UU depth 5.4

CRBFV 9025 AT CRBFV 9025 AT UU 4.83 12-M8 through

12-φ9 through
90 CRBFV 9025 A CRBFV 9025 A UU 90 210 25 1.5 1.5 112 12- φ 9 through 187 φ14 counter bore 132 168 73 400 108 000
4.67 φ 14 counter bore depth 12
CRBFV 9025 AD CRBFV 9025 AD UU depth 12

CRBFV 11528 AT CRBFV 11528 AT UU 6.81 12-M8 through

12-φ9 through
115 CRBFV 11528 A CRBFV 11528 A UU 115 240 28 1.5 1.5 139 12- φ 9 through 217 φ14 counter bore 162 198 84 300 138 000
6.63 φ 14 counter bore depth 13.5
CRBFV 11528 AD CRBFV 11528 AD UU depth 13.5

Note(1)　　 Minimum allowable single value of chamfer diameter r1 and r2.

Remarks1.   The outer ring has an oil groove and two oil holes.
2.   No grease is prepacked for Open Type. Perform proper lubrication. Grease is prepacked for Sealed Type.
3.   If one side sealed type are needed, please contact .

1N=0.102kgf=0.2248lbs.
J25 1mm=0.03937inch
J26
 ■ Structure and Features Structures of Spherical Bushings
Spherical Bushings are self-aligning spherical Steel-on-steel type
plain bushings that have inner and outer rings with
spherical sliding surfaces, and can take a large radial Outer ring
(MoS2 coating)
load and a bi-directional axial load at the same time.
●Steel-on-steel Spherical Bushings There are many types of Spherical Bushings, but they
Inner ring
are basically divided into steel-on-steel types and (MoS2 coating)
●Maintenance-free Spherical Bushings maintenance-free types according to the kind of slid-
ing surfaces.
Steel-on-steel Spherical Bushings have inner and
outer rings of high carbon chromium bearing steel, of
which sliding surfaces are phosphate-treated and
then dry-coated with molybdenum disulfide (MoS2).
They can, therefore, operate with low torque, and Steel-on-steel type
have excellent wear resistance and large load capaci- Outer ring
ty. They are especially suitable for applications where (MoS2 coating)
there are alternate loads and shock loads. They have
Inner ring
wide applications mainly in industrial and construction
(MoS2 coating)
machinery.
Maintenance-free Spherical Bushings consist of an
outer ring which has a special PTFE liner reinforced
with copper alloy meshes on the sliding surface, and
a spherical inner ring of which sliding surface has a
hard chromium plating. Creep deformation due to
compressive load is small, and wear resistance is Seal
Maintenance-free type (Polyurethane)
superior. Thus, they are maintenance-free and can
be used for extended periods of time without re-lubri-
cation. They are especially suitable in cases where Outer ring
fixed directional loads are applied and are used main-
Special PTFE liner
ly in food processing machines and construction (Reinforced with copper alloy meshes)
machinery and in other applications in which the use
of oil is undesirable or lubrication is not possible.
Inner ring
(Chromium plating)

■ Types
Spherical Bushings are available in various types Maintenance-free type
shown in Table 1.
Outer ring
Table 1 Type of bearing
Special PTFE liner

K
Type
Steel-on-steel Maintenance-free (Reinforced with copper alloy meshes)

Series Without seals With seals Without seals With seals

SB −
Inner ring
SB … A − (Chromium plating)
Metric GE … EC GE … EC-2RS
GE … E，ES GE … ES-2RS
GE … G，GS GE … GS-2RS Seal
(Synthetic resin)
Inch SBB SBB …  -2RS − −

K1 K2
Steel-on-steel Spherical Bushings  SB Maintenance-free Spherical Bushings  GE … EC ■ Accuracy Table 3 Tolerances of inner and outer rings of inch series SBB
d or D（1） ∆ dmp ∆ Dmp
unit: μ m

∆ Bs or ∆ Cs
These bushings have an outer ring split into halves. These bushings have the same boundary dimensions The tolerances of Steel-on-steel Spherical Bushings Nominal bore dia. or Single plane Single plane Deviation of a single
The split outer ring and the inner ring are held togeth- as the GE … ES type and can be used internationally. of the metric series is shown in Table 2. outside dia. mean bore mean outside inner ring width or
er by a snap ring placed in the groove around the A special PTFE liner reinforced with copper alloy The tolerances of the GE type are applicable to bush- mm dia. deviation dia. deviation outer ring width
outer periphery of the outer ring. meshes is used on the sliding surface. Therefore, ings before splitting the outer ring and after surface Over Incl. High Low High Low High Low
creep deformation due to compressive loads is small, treatment.
− 50.800 0 − 13 0 − 13 0 − 130
Steel-on-steel Spherical Bushings   SB … A and wear resistance is superior. These bushings are The tolerances of the SB and SB…A types are applic-
50.800 76.200 0 − 15 0 − 15 0 − 130
used as maintenance-free bushings. able to bushings before splitting the outer ring and
These bushings have an outer ring split only at one These bushings can be provided with synthetic resin before surface treatment. 76.200 80.962 0 − 20 0 − 15 0 − 130
position, and therefore, the outer and inner rings will seals which are effective in preventing dust penetra- The tolerances of the GE…EC type are applicable to 80.962 120.650 0 − 20 0 − 20 0 − 130
not separate. Handling before mounting and mount- tion. They are indicated by the suffix "-2RS" at the bushings before splitting the outer ring. 120.650 152.400 0 − 25 0 − 25 0 − 130
ing to the housing are simple. The boundary dimen- end of the identification number. The tolerances of the Spherical Bushings of the inch 152.400 177.800 − − 0 − 25 0 − 130
sions are the same as those of the SB type.Therefore, Spherical Bushings with superior rust prevention series are shown in Table 3. The tolerances of the 177.800 222.250 − − 0 − 30 0 − 130
SB and SB … A types are dimensionally interchange- properties, which can be used in a corrosive environ- bore diameter are applicable to bushings after surface
Note(1)　d for ∆ dmp, ∆ Bs and ∆ Cs and D for ∆ Dmp, respectively.
able, but the radial internal clearances of the SB … A ment or in an environment where water splashes, are treatment, while other tolerances are applicable to
type are smaller than those of the SB type. also available on request. Please consult . bushings before splitting the outer ring and before

Steel-on-steel Spherical Bushings  GE … E，GE … ES

surface treatment.
Although minor dimensional changes may occur dur- ■ Clearance
The dimension series of these types conform to ISO ■ Identification number ing surface treatment, they have negligible influence
on the overall performance.
The radial internal clearances of Spherical Bushings
are the values before splitting the outer ring, and are
standards and they can be used internationally. The The identification number of Spherical Bushings con- shown in Tables 4, 5 and 6. The radial internal clear-
outer ring is split at one position. The GE … E and GE sists of a model code, a size and any supplemental Table 2 Tolerances of inner and outer rings of metric series (JIS Class 0) unit: μ m ances of the inch series are shown in the dimension
… ES types are available. These are classified by codes. Examples are shown below. table.
d or D（1） ∆ dmp ∆ Dmp ∆ Bs or ∆ Cs
bushing size. Nominal bore dia. Single plane Single plane Deviation of a single Clearances other than these can also be prepared on
The GE … ES type can be provided with seals, which or outside dia. mean bore dia. mean outside inner ring width or request. Please consult .
are double-lip type polyurethane seals effective for mm deviation dia. deviation outer ring width
prevention against grease leakage and dust penetra- Over Incl. High Low High Low High Low Table 4 Radial internal clearance of SB and SB … A types (Steel-on-steel)
tion. The sealed type is indicated by the suffix "-2RS" unit: μ m
    2.5     6 0 −  8 − − 0 − 120
at the end of the identification number. d SB type SB … A type
    6   18 0 −  8 0 −  8 0 − 120 Nominal bore dia.
mm Min. Max. Min. Max.
  18   30 0 − 10 0 −  9 0 − 120
Steel-on-steel Spherical Bushings  GE … G，GE … GS 12 32 68
  30   50 0 − 12 0 − 11 0 − 120 15
70 125
40 82
As compared with the GE … E and GE … ES types,   50   80 0 − 15 0 − 13 0 − 150 20
these bushings have larger load capacities and larger   80 120 0 − 20 0 − 15 0 − 200 22
75 140
permissible tilting angles. The dimension series also 25
120 150 0 − 25 0 − 18 0 − 250 30
50 100
conform to ISO standards, and they can be used
150 180 0 − 25 0 − 25 0 − 250 35
internationally. The outer ring is split at one position.
180 250 0 − 30 0 − 30 0 − 300 40
The GE … G and GE … GS types are available. They 85 150
45
are classified by bushing size. 250 315 0 − 35 0 − 35 0 − 350 50
60 120
The GE … GS type can be provided with seals, which 315 400 0 − 40 0 − 40 0 − 400 55
are double-lip type polyurethane seals effective for
prevention against grease leakage and dust penetra-
400
Note(1)　
500 0 − 45 0 − 45 0
d for ∆ dmp, ∆ Bs and ∆ Cs and D for ∆ Dmp, respectively.
− 450 60
65
90 160
K
70 72 142
tion. The sealed type is indicated by the suffix "-2RS" 95 170
75
at the end of the identification number. 80
85
90
Steel-on-steel Spherical Bushings  SBB 95
100 185
100 85 165
These are inch series bushings. The outer ring is split
110
at one position. 110 200
115
These bushings can be provided with seals, which are 120
double-lip type polyurethane seals effective for pre- 130
120 215 100 192
vention against grease leakage and dust penetration. 150
The sealed type is indicated by the suffix "-2RS" at
the end of the identification number.

1N=0.102kgf=0.2248lbs.
K3 1mm=0.03937inch
K4
Table 5 Radial internal clearance of GE type (Steel-on-steel)
unit: μ m
■ Fit Table 10 Temperature factor　ft
Temperature　℃
Before attempting to calculate the life, make sure that
the operating conditions are within the permissible
d The recommended fits for Spherical Bushings are range by referring to the pV diagram in Fig.1.
Type of bushing − 30 ＋ 80 ＋  90 ＋ 100 ＋ 120 ＋ 150
Nominal bore dia. shown in Tables 7 and 8.
Radial internal clearance ＋ 80 ＋ 90 ＋ 100 ＋ 120 ＋ 150 ＋ 180 When the operating conditions are out of the permis-
mm
sible range, please consult .
Table 7 Recommended fits for Steel-on-steel Spherical Bushings
GE…E GE…G Steel-on- Without seals 1 1 1 1 1 0.7 The contact pressure p and the sliding velocity V are
GE…ES GE…GS Min. Max. Tolerance class steel
Condition With seals 1 − − − − − obtained from the following equations.
4 − Shaft Housing bore 　　　 100P
5 − Without seals 1 1 0.9 0.75 0.55 − 　　　　 　
p＝ ……………………………………(3)
Normal operation h6，j6 H7，J7 Maintena Cdt
6 − nce-free With seals −4
32 68 With directionally indeterminate load m6，n6 M7，N7 1 − − − − − 　　　V＝5.82×10 dkβf ………………………(4)
8 6
10 8 Remark　N7 tolerance is recommended for light metal housings. 　　where,　p：Contact pressure　N/mm2
  2  Static load capacity
12 10
The static load capacity Cs is the maximum static load 　　　　　   P：Equivalent radial load N (Refer to equation (2). )
15 12 Table 8 Recommended fits for Maintenance-free Spherical Bushings
that can be applied on the spherical bushing without 　　　　 　Cdt：Dynamic load capacity considering temperature increase　N
17 15 40 82 Tolerance class of
20 17 Tolerance class of shaft breaking inner and outer rings or causing any perma- (Refer to equation (1).)
housing bore
25 20 nent deformation severe enough to render the bush- 　　　　　 V：Sliding velocity　mm/s
30 25 50 100 h6，j6 H7，J7，K7 ing unusable. 　　　　 　dk：Sphere diameter　mm
35 30 Remark　K7 tolerance is recommended for light metal housings. It must be noted that if the magnitude of the applied (Refer to the dimension tables.)
40 35
load becomes comparable to the static load capacity 　　　　　2β：Oscillating angle　degrees (Refer to Fig.2.)
■ Selection of Spherical Bushings
45 40
60 120 of bushing, the stresses in the shaft or housing may
50 45 , β＝5
　　　　　　　  when β＜5°
also reach to their limits. This possibility must be
60 50 　　　　　　　  when rotating, 　β＝90
70 60 Selection between the steel-on-steel type and the taken into consideration in the design.
　　　　　 f：Number of oscillations per minute　min-1
80 70 72 142 maintenance-free type is made considering the oper-
90 80 ating conditions such as load, lubrication, tempera- Equivalent radial load
100 90 ture, and sliding velocity.
110 100 Spherical Bushings can take radial and axial loads at 100 When alternate loads
85 165
120 110
140 120
Load capacity the same time. When the magnitude and direction of
80
60
are applied, this range
is also permissible.
loads are constant, the equivalent radial load can be
160 140 1 Dynamic load capacity
40
180 160 obtained from the following equation.
The dynamic load capacity Cd is the maximum allow-

p N/mm2
200 180 100 192 　　　P ＝ Fr ＋ YFa  …………………………………(2) 20
able load that can be applied on a spherical bushing
220 200 　　where,     P：Equivalent radial load　N Permissible range
240 220 under oscillating motion. It is obtained on the basis of 10
　　　　 　Fr：Radial load　N 8
260 240 the contact pressure on the spherical surfaces. The

Contact pressure
280 260 110 214 　　　　 　Fa：Axial load　N 6
dynamic load capacity is also used for calculating the 4
300 280 life of spherical bushings. 　　　　 　　Y：Axial load factor (Refer to Table 11.)
Remark　Also applicable to bushings with seals.
The recommended value of bushing load is obtained Table 11 Axial load factor　Y 2
by multiplying the dynamic load capacity Cd by a Fa/Fr
Table 6 Radial internal clearance of GE … EC type (Maintenance-free) 0.1 0.2 0.3 0.4 0.5 ＞ 0.5 1
numerical factor, which differs depending on the Type of bushing 1 2 4 6 10 20 40 60 100 200
unit: μ m
bushing type and the load condition. A guideline for Steel-on-steel 1 2 3 4 5 Unusable Sliding velocity V mm/s
d Radial internal clearance selection is shown in Table 9.
Nominal bore dia. Maintenance-free 1 2 3 Unusable
Fig.1 pV diagram of Steel-on-steel spherical bushings
mm Min. Max. Table 9 Guide for determination of load

K
15
17 0 40 Type of bushing
Load direction Life
20 Constant Alternate
The life of Spherical Bushings is defined as the total
25 Steel-on-steel ≦ 0.3Cd ≦ 0.6Cd
number of oscillating motions before the bushings
30 0 50 Maintenance-free ≦ Cd ≦ 0.5Cd
35 cannot be operated normally because of wear,
40 increase in internal clearance, increase in sliding
When the magnitude of load exceeds the value given
45 torque, rise of operating temperature, etc.
0 60 in Table 9, please consult .
50 As the actual life is affected by many factors such as
60 The dynamic load capacity Cdt considering the influ-
the material of the sliding surface, the magnitude and
70 0 72 ence of bushing temperature can be obtained from
direction of load, lubrication, sliding velocity, etc., the β β
Remark　Also applicable to bushings with seals. the following equation using the temperature factor.
calculated life can be used as a practical measure of Oscillating angle
　　　Cdt＝ft Cd    ……………………………………(1)
expected service life.
　　where,  Cdt：Dynamic load capacity considering temperature increase N
  1  Life of Steel-on-steel spherical bushings Fig.2 Oscillating angle
　　　　　　 ft：Temperature factor (Refer to Table 10.)
［1］Confirmation of pV value
　　　 　 　Cd：Dynamic load capacity N (Refer to the dimension tables.)

1N=0.102kgf=0.2248lbs.
K5 1mm=0.03937inch
K6
［2］Life calculation   2  Life of Maintenance-free spherical bushings
［1］Confirmation of pV value
100
The life of steel-on-steel spherical bushings can be
calculated from the following equations. Before attempting to calculate the life, make sure that 90
　　　   3.18b1b2b3　 Cdt　 2 

（　   ）
the operating conditions are within the permissible
　　　　　　
5
G＝ ×10   …………… (5) 80
 dk β　        P range by referring to the pV diagram in Fig.4.
　　　      G　  When the operating conditions are out of the permis- 70
Lh ＝     ……………………………………(6)

N / mm 2
　　　　    60f sible range, please consult .
60
　　where, G：Life (Total number of oscillations) The contact pressure p and the sliding velocity V are
　　　　　 b1：Load directional factor (Refer to Table 12.) obtained from equations (3) and (4) shown on page

p
50
J10.

Contact pressure
　　　　　 b2：Lubrication factor (Refer to Table 13.) 40
　　　　　 b3：Sliding velocity factor (Refer to Fig.3.)
［2］Life calculation
The life of maintenance-free spherical bushings is 30
　　　　　Cdt：Dynamic load capacity considering temperature increase　N
obtained from the total sliding distance S which is
(Refer to equation (1).) 20
given in Fig.5 for the contact pressure p obtained from
　　　　　 P：Equivalent radial load　N   
equation (3). 10
(Refer to equation (2).)
The total number of oscillations and life in hours can
　　　　 　Lh：Life in hours　h be obtained from the following equations.
0
1 2 5 10 20 50 100 200 500 1000 ×103
　　　　　 f：Number of oscillations per minute　min-1 　　　   Sf    
　　　　　　 G ＝ 16.67 ×　   b1 …………………………(7) Total sliding distance S m
V
Table 12 Load directional factor b1 (Steel-on-steel)　 　　　     G　   Fig.5 Total sliding distance against contact pressure of Maintenance-free spherical bushings
Lh ＝    ……………………………………(8)
　　　　    60f
Load direction Constant Alternate
　　where,　G：Life (Total number of oscillations)
Load directional factor　b1 1 5 　　　　　　b1：Load directional factor (Refer to Table 14.)
　　　　　　 S：Total sliding distance m (Refer to Fig.5.) ■ Lubrication ■ Oil Hole
　　　　　　  f：Number of oscillations per minute　min-1
Table 13 Lubrication factor　b2 Steel-on-steel Spherical Bushings can be operated The number of oil holes on inner and outer rings is
　　　　　　 V：Sliding velocity　mm/s
without lubrication when the magnitude of applied shown in Table 15.
Periodical lubrication None Regular 　　　　　   Lh：Life in hours　h load is small and the sliding velocity of oscillation is
Lubrication factor　b2 1 15 small. However, in general, it is necessary to supply Table 15 Number of oil holes on inner and outer rings
100
grease periodically. During initial operation, it is rec- Number of oil
When alternate loads
are applied, this range ommended to shorten the lubrication interval. Lithium Bushing type holes on inner
60 is also permissible. and outer rings
5 soap base grease (NLGI consistency No.2) containing
4
3
40
molybdenum disulfide (M0S2) is widely used as the GE … E
0
Contact pressure p N/mm2

2 lubricating grease. GE … G
20
Steel-on-steel Metric series
1 Permissible range Maintenance-free Spherical Bushings can be used Spherical Bushings
SB，SB … A
ate 2
rn 10 without lubrication. However, if lithium soap base GE … ES，GE … GS
lte 8
:A
Sliding velocity factor b 3

0.5
0.4 on 6 grease is supplied before operation, the spherical Inch series SBB 2
cti
0.3 re bushings can be operated for an extended period of
nt

di 4
sta

0.2
oa
d Maintenance-free
Metric series GE … EC 0
on

L time. The spherical bushings can be effectively pro- Spherical Bushings

:C

tected from dust and rust if the space around the

on

0.1 2
cti

Remark　Types with oil holes are also provided with oil grooves on
re

bushings is filled with grease.

K
di

0.05 inner and outer rings.

1
ad

0.04
Lo

0.03 1 2 4 6 10 20 40 60 100 200

0.02
Sliding velocity V mm/s
0.01 Fig.4 pV diagram of Maintenance-free spherical bushings
0.2 0.5 1 5 10 50 100 150
Sliding velocity V mm / s

Table 14 Load directional factor b1 (Maintenance-free)

Fig.3 Sliding velocity factor Load direction Constant Alternate

Load directional factor　b1 1 0.2（1）

Note(1)　This value is applicable when the load changes compara-
tively slowly. When the load changes rapidly, please con-
sult , as the factor degreases sharply.

1N=0.102kgf=0.2248lbs.
K7 1mm=0.03937inch
K8
■ Operating Temperature Range   2  When the load acts in the Yu direction ; ■ Mounting
Select the housing material considering the tensile
The operating temperature range for Spherical  1 When mounting Spherical Bushings, pay attention Load
stress obtained from the following equation. 　
Bushings with seals is -30゜C〜+80゜ C. to the location of the split plane of the outer ring. Set
　　　  　　F　       
The maximum allowable temperature for Spherical 　　　　　
σ2＝ k ………………………(10) the split plane at right angles to the direction of load to
 C（DH−D）
Split plane
Bushings without seals is +180 ゜ C for the steel-on- avoid the application of load to the split plane as
　　where,　 σ2：Maximum tensile stress occurring
steel type and +150 ゜C for the maintenance-free type. shown in Fig. 8.
in the housing bore　N/mm2  2 The shoulder dimensions of shaft and housing are
　　　　　　　F：Applied load　N shown in the dimension tables.
■ Precautions for Use 　　　　　　　C：Width of outer ring and housing　mm
　　　　　　 DH：Outside diameter of housing　mm
　　　　　　　D：Outside diameter of outer ring　mm
Design of shaft 　　　　　　 　k：Stress concentration factor (Refer to Fig.7.)
Load

When the load is large, sliding may occur between the Fig.8 R
 elationship between the split plane
shaft and the inner ring bore of bushing. For such 9 and the loading direction
cases, it is necessary to prepare the shaft with a hard-
8
ness of 58HRC or greater and surface roughness of
0.8 μmRa or less. 7
Furthermore, attention must be paid to the strength of When setting the interference fit side When the inner and outer rings are assembled at the same time
6
shaft because the shear and/or bending stresses in

Stress concentration factor k

the shaft may surpass the allowable values even 5

when the load is below the static load capacity of 4

Spherical Bushings.
3

Design of housing 2

The housing should have sufficient rigidity to avoid 1

harmful deformation under load.
0
When the housing shown in Fig.6 is used, it should be 0 1 2 3 4 5 6 7 8 9
designed with sufficient strength as follows.
DH / D

C DH
Fig.7 Stress concentration factor
YU

Fig.9 Mounting method

F
D

K
YL

Fig.6 Shape of housing

  1  When the load acts in the YL direction;

Select the housing material considering the compres-
sive stress obtained from the following equation.
  　　　
σ1＝ F   ……………………………………(9)
       
　　　　       
CD
　　where,　 σ1：Maximum compressive stress occur- Fig.10 Mounting examples
ring in the housing bore　N/mm2
　　　　　　　F：Applied load　N
　　　　　　　C：Width of outer ring and housing　mm
　　　　　　　D：Outside diameter of outer ring　mm

1N=0.102kgf=0.2248lbs.
K9 1mm=0.03937inch
K10
 SPHERICAL BUSHINGS
Steel-on-steel Spherical Bushings
B B
C C

r2 r2

r1 r1
α α

Da
D
D

da
d

d
α α

dk

dk
r1 r1

r2 r2

SB … A SB
Shaft dia. 12 − 100mm

Identification number Mass Boundary dimensions Permissible Mounting dimensions Dynamic load Static load
Shaft (Ref.) mm tilting angle mm capacity capacity
degree
dia.
da Da Cd Cs
(1)
mm kg d D B C dk rs min α Min. Max. (2) Max. Min.
N N
12 SB 12A SB 122211 0.019 12 22 11 9 18 0.3 7 14 14 19.5 17 15 900 95 300
15 SB 15A SB 152613 0.028 15 26 13 11 22 0.3 6 17.5 17.5 23.5 21 23 700 142 000
20 SB 20A SB 203216 0.053 20 32 16 14 28 0.3 4 22.5 23 29.5 26 38 400 231 000
22 SB 22A SB 223719 0.085 22 37 19 16 32 0.3 6 24.5 25.5 34.5 30 50 200 301 000
25 SB 25A SB 254221 0.116 25 42 21 18 36 0.3 5 27.5 29 39.5 34 63 500 381 000
30 SB 30A SB 305027 0.225 30 50 27 23 45 0.6 6 34.5 36 45.5 42 101 000 609 000
35 SB 35A SB 355530 0.300 35 55 30 26 50 0.6 5 39.5 40 50.5 46.5 127 000 765 000
40 SB 40A SB 406233 0.375 40 62 33 28 55 0.6 6 44 44 57.5 51.5 151 000 906 000
45 SB 45A SB 457236 0.600 45 72 36 31 62 0.6 5 49.5 50.5 67.5 58 188 000 1 130 000
50 SB 50A SB 508042 0.870 50 80 42 36 72 0.6 5 54.5 58.5 75.5 67 254 000 1 530 000
55 SB 55A SB 559047 1.26 55 90 47 40 80 0.6 5 59.5 64.5 85.5 74.5 314 000 1 880 000
60 SB 60A SB 6010053 1.70 60 100 53 45 90 0.6 6 64.5 72.5 95.5 83.5 397 000 2 380 000
65 SB 65A SB 6510555 2.05 65 105 55 47 94 0.6 5 69.5 76 100.5 87 433 000 2 600 000
70 SB 70A SB 7011058 2.22 70 110 58 50 100 0.6 5 74.5 81.5 105.5 93 490 000 2 940 000
75 SB 75A SB 7512064 3.02 75 120 64 55 110 0.6 5 79.5 89.5 115.5 102 593 000 3 560 000 K
80 SB 80A SB 8013070 3.98 80 130 70 60 120 0.6 5 84.5 97.5 125.5 112 706 000 4 240 000
85 SB 85A SB 8513574 4.29 85 135 74 63 125 0.6 6 89.5 100.5 130.5 116 772 000 4 630 000
90 SB 90A SB 9014076 4.71 90 140 76 65 130 0.6 5 94.5 105.5 135.5 121 829 000 4 970 000
95 SB 95A SB 9515082 6.05 95 150 82 70 140 0.6 5 99.5 113.5 145.5 130 961 000 5 770 000
100 SB 100A SB 10016088 7.42 100 160 88 75 150 1 5 105.5 121.5 154.5 139 1 100 000 6 620 000

Notes(1)　　Minimum allowable value of chamfer dimensions r1 and r2

 　　  (2)　　When Spherical Bushings are used with full tilting angle, the shaft shoulder dimesion must be less than the maximum value of da.
Remarks1.　The inner ring and the outer ring have an oil groove and two oil holes, respectively.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
K11 1mm=0.03937inch
K12
 SPHERICAL BUSHINGS
Steel-on-steel Spherical Bushings
B B
C C

r2 r2

r1 r1
α α

Da
D
D

da
d

d
α α

dk

dk
r1 r1

r2 r2

SB … A SB
Shaft dia. 110 − 150mm

Identification number Mass Boundary dimensions Permissible Mounting dimensions Dynamic load Static load
Shaft (Ref.) mm tilting angle mm capacity capacity
degree
dia.
da Da Cd Cs
(1)
mm kg d D B C dk rs min α Min. Max. (2) Max. Min.
N N
110 SB 110A SB 11017093 8.55 110 170 93 80 160 1 5 115.5 130 164.5 149 1 260 000 7 530 000
115 SB 115A SB 11518098 10.3 115 180 98 85 165 1 5 120.5 132.5 174.5 152 1 380 000 8 250 000
120 SB 120A SB 120190105 12.4 120 190 105 90 175 1 5 125.5 140 184.5 162 1 540 000 9 270 000
130 SB 130A SB 130200110 13.8 130 200 110 95 185 1 5 135.5 148.5 194.5 171 1 720 000 10 300 000
150 SB 150A SB 150220120 17.0 150 220 120 105 205 1 5 155.5 166 214.5 189 2 110 000 12 700 000

Notes(1)　　Minimum allowable value of chamfer dimensions r1 and r2

 　　 (2)　　When Spherical Bushings are used with full tilting angle, the shaft shoulder dimension must be less than the maximum value of da.
Remarks1.　The inner ring and the outer ring have an oil groove and two oil holes, respectively.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
K13 1mm=0.03937inch
K14
 SPHERICAL BUSHINGS
Steel-on-steel Spherical Bushings
B B B
C C C

r2 r2 r2

r1 r1 r1
α α α1

D
D

Da
D

da
d
d

d
α α α1

dK

dk
dk
r1 r1 r1
r2 r2 r2

GE … E GE … ES GE … ES-2RS
Shaft dia. 4 − 100mm

Identification number Mass Boundary dimensions Permissible Mounting dimensions Dynamic load Static load
Shaft (Ref.) mm tilting angle mm capacity capacity
degree
dia.
da Da Cd Cs
(1) (1)
mm
Without seals With seals
kg d D B C dk r1s min r2s min α α1 Min. Max. (2) Max. Min.
N N
4 GE 4E ─ 0.003 4 12 5 3 8 0.3 0.3 16 ─ 6 6 9.5 8 2 350 14 100
5 GE 5E ─ 0.004 5 14 6 4 10 0.3 0.3 13 ─ 7.5 8 11.5 10 3 920 23 500
6 GE 6E ─ 0.004 6 14 6 4 10 0.3 0.3 13 ─ 8 8 11.5 10 3 920 23 500
8 GE 8E ─ 0.008 8 16 8 5 13 0.3 0.3 15 ─ 10 10 13.5 13 6 370 38 200
10 GE 10E ─ 0.012 10 19 9 6 16 0.3 0.3 12 ─ 12.5 13 16.5 15.5 9 410 56 500
12 GE 12E ─ 0.017 12 22 10 7 18 0.3 0.3 11 ─ 14.5 15 19.5 17 12 400 74 100
15 GE 15ES GE 15ES-2RS 0.032 15 26 12 9 22 0.3 0.3 8 5 17.5 18 23.5 22.5 19 400 117 000
17 GE 17ES GE 17ES-2RS 0.049 17 30 14 10 25 0.3 0.3 10 7 19.5 20.5 27.5 26 24 500 147 000
20 GE 20ES GE 20ES-2RS 0.065 20 35 16 12 29 0.3 0.3 9 6 22.5 24 32.5 30.5 34 100 205 000
25 GE 25ES GE 25ES-2RS 0.115 25 42 20 16 35.5 0.6 0.6 7 4 29 29 37.5 37 55 700 334 000
30 GE 30ES GE 30ES-2RS 0.160 30 47 22 18 40.7 0.6 0.6 6 4 34 34 42.5 41.5 71 800 431 000
35 GE 35ES GE 35ES-2RS 0.258 35 55 25 20 47 0.6 1 6 4 39.5 39.5 49.5 48 92 200 553 000
40 GE 40ES GE 40ES-2RS 0.315 40 62 28 22 53 0.6 1 7 4 44.5 45 56.5 54.5 114 000 686 000
45 GE 45ES GE 45ES-2RS 0.413 45 68 32 25 60 0.6 1 7 4 49.5 50.5 62.5 60 147 000 883 000
50 GE 50ES GE 50ES-2RS 0.560 50 75 35 28 66 0.6 1 6 4 54.5 56 69.5 66 181 000 1 090 000 K
60 GE 60ES GE 60ES-2RS 1.10 60 90 44 36 80 1 1 6 3 65.5 66.5 84.5 79 282 000 1 690 000
70 GE 70ES GE 70ES-2RS 1.54 70 105 49 40 92 1 1 6 4 75.5 77.5 99.5 91 361 000 2 170 000
80 GE 80ES GE 80ES-2RS 2.29 80 120 55 45 105 1 1 6 4 85.5 89 114.5 103 463 000 2 780 000
90 GE 90ES GE 90ES-2RS 2.82 90 130 60 50 115 1 1 5 3 95.5 98 124.5 112 564 000 3 380 000
100 GE 100ES GE 100ES-2RS 4.43 100 150 70 55 130 1 1 7 5 105.5 109.5 144.5 127 701 000 4 210 000

Notes(1)　　Minimum allowable value of chamfer dimensions r1 and r2

 　　  (2)　　When Spherical Bushings are used with full tilting angle, the shaft shoulder dimension must be less than the maximum value of da.
Remarks1.　GE…E has no oil hole. Others are provided with an oil groove and two oil holes on the inner ring and outer ring, respectively.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
K15 1mm=0.03937inch
K16
 SPHERICAL BUSHINGS
Steel-on-steel Spherical Bushings
B B
C C

r2 r2

r1 r1
α α1

Da
D

da
d
d
α α1

dk
dk
r1 r1

r2 r2

GE … ES GE … ES-2RS
Shaft dia. 110 − 300mm

Identification number Mass Boundary dimensions Permissible Mounting dimensions Dynamic load Static load
Shaft (Ref.) mm tilting angle mm capacity capacity
degree
dia.
da Da Cd Cs
(1) (1)
mm
Without seals With seals
kg d D B C dk r1s min r2s min α α1 Min. Max. (2) Max. Min.
N N
110 GE 110ES GE 110ES-2RS 4.94 110 160 70 55 140 1 1 6 4 115.5 121 154.5 138 755 000 4 530 000
120 GE 120ES GE 120ES-2RS 8.12 120 180 85 70 160 1 1 6 4 125.5 135.5 174.5 154 1 100 000 6 590 000
140 GE 140ES GE 140ES-2RS 11.4 140 210 90 70 180 1 1 7 5 145.5 155.5 204.5 176 1 240 000 7 410 000
160 GE 160ES GE 160ES-2RS 14.4 160 230 105 80 200 1 1 8 6 165.5 170 224.5 195 1 570 000 9 410 000
180 GE 180ES GE 180ES-2RS 18.9 180 260 105 80 225 1.1 1.1 6 5 187 199 253 221 1 770 000 10 600 000
200 GE 200ES GE 200ES-2RS 28.1 200 290 130 100 250 1.1 1.1 7 6 207 213.5 283 244 2 450 000 14 700 000
220 GE 220ES GE 220ES-2RS 36.1 220 320 135 100 275 1.1 1.1 8 6 227 239.5 313 269 2 700 000 16 200 000
240 GE 240ES GE 240ES-2RS 40.4 240 340 140 100 300 1.1 1.1 8 6 247 265 333 296 2 940 000 17 700 000
260 GE 260ES GE 260ES-2RS 52.0 260 370 150 110 325 1.1 1.1 7 6 267 288 363 320 3 510 000 21 000 000
280 GE 280ES GE 280ES-2RS 66.0 280 400 155 120 350 1.1 1.1 6 5 287 313.5 393 345 4 120 000 24 700 000
300 GE 300ES GE 300ES-2RS 76.0 300 430 165 120 375 1.1 1.1 7 6 307 336.5 423 371 4 410 000 26 500 000

Notes(1)　　Minimum allowable value of chamfer dimensions r1 and r2

 　　 (2)　　When Spherical Bushings are used with full tilting angle, the shaft shoulder dimension must be less than the maximum value of da.
Remarks1.　The inner ring and the outer ring have an oil groove and two oil holes, respectively.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
K17 1mm=0.03937inch
K18
 SPHERICAL BUSHINGS
Steel-on-steel Spherical Bushings B
B B
C C
C

r2 r2 r2

r1 r1 r1
α α α1

D
D

Da
D

da
d
d
d
α

dK
α α1

dk
dk
r1 r1 r1

r2 r2 r2

GE … G GE … GS GE … GS-2RS
Shaft dia. 6 − 120mm

Identification number Mass Boundary dimensions Permissible Mounting dimensions Dynamic load Static load
Shaft (Ref.) mm tilting angle mm capacity capacity
degree
dia.
da Da Cd Cs
(1) (1)
mm
Without seals With seals
kg d D B C dk r1s min r2s min α α1 Min. Max. (2) Max. Min.
N N
6 GE 6G ─ 0.010 6 16 9 5 13 0.3 0.3 21 ─ 8.5 9 13.5 13 6 370 38 200
8 GE 8G ─ 0.015 8 19 11 6 16 0.3 0.3 21 ─ 10.5 11.5 16.5 15.5 9 410 56 500
10 GE 10G ─ 0.022 10 22 12 7 18 0.3 0.3 18 ─ 12.5 13 19.5 17 12 400 74 100
12 GE 12G ─ 0.041 12 26 15 9 22 0.3 0.3 18 ─ 14.5 16 23.5 21 19 400 117 000
15 GE 15GS GE 15GS-2RS 0.059 15 30 16 10 25 0.3 0.3 16 13 17.5 19 27.5 26 24 500 147 000
17 GE 17GS GE 17GS-2RS 0.083 17 35 20 12 29 0.3 0.3 19 16 19.5 21 32.5 30.5 34 100 205 000
20 GE 20GS GE 20GS-2RS 0.155 20 42 25 16 35.5 0.3 0.6 17 16 22.5 25 37.5 37 55 700 334 000
25 GE 25GS GE 25GS-2RS 0.215 25 47 28 18 40.7 0.6 0.6 17 15 29.5 29.5 42.5 41.5 71 800 431 000
30 GE 30GS GE 30GS-2RS 0.330 30 55 32 20 47 0.6 1 17 16 34 34 49.5 48 92 200 553 000
35 GE 35GS GE 35GS-2RS 0.400 35 62 35 22 53 0.6 1 16 15 39.5 39.5 56.5 54.5 114 000 686 000
40 GE 40GS GE 40GS-2RS 0.515 40 68 40 25 60 0.6 1 17 14 44.5 44.5 62.5 60 147 000 883 000
45 GE 45GS GE 45GS-2RS 0.660 45 75 43 28 66 0.6 1 15 13 49.5 50 69.5 66 181 000 1 090 000
50 GE 50GS GE 50GS-2RS 1.50 50 90 56 36 80 0.6 1 17 16 54.5 57 84.5 79 282 000 1 690 000
60 GE 60GS GE 60GS-2RS 2.05 60 105 63 40 92 1 1 17 15 65.5 67 99.5 91 361 000 2 170 000
70 GE 70GS GE 70GS-2RS 3.00 70 120 70 45 105 1 1 16 14 75.5 78 114.5 103 463 000 2 780 000 K
80 GE 80GS GE 80GS-2RS 3.60 80 130 75 50 115 1 1 14 13 85.5 87 124.5 112 564 000 3 380 000
90 GE 90GS GE 90GS-2RS 5.41 90 150 85 55 130 1 1 15 14 95.5 98 144.5 127 701 000 4 210 000
100 GE 100GS GE 100GS-2RS 6.15 100 160 85 55 140 1 1 14 12 105.5 111 154.5 138 755 000 4 530 000
110 GE 110GS GE 110GS-2RS 9.70 110 180 100 70 160 1 1 12 11 115.5 124.5 174.5 154 1 100 000 6 590 000
120 GE 120GS GE 120GS-2RS 15.5 120 210 115 70 180 1 1 16 15 125.5 138.5 204.5 176 1 240 000 7 410 000

Notes(1)　　Minimum allowable value of chamfer dimensions r1 and r2

 　　  (2)　　When Spherical Bushings are used with full tilting angle, the shaft shoulder dimension must be less than the maximum value of da.
Remarks1.　GE…G has no oil hole. Others are provided with an oil groove and two oil holes on the inner ring and outer ring, respectively.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
K19 1mm=0.03937inch
K20
 SPHERICAL BUSHINGS
Steel-on-steel Spherical Bushings B
B
C
C

r2 r2

r1 r1
α α1

D
D

Da

da
d
d
α α1

dk
dk
r1 r1

r2 r2

GE … GS GE … GS-2RS
Shaft dia. 140 − 280mm

Identification number Mass Boundary dimensions Permissible Mounting dimensions Dynamic load Static load
Shaft (Ref.) mm tilting angle mm capacity capacity
degree
dia.
da Da Cd Cs
(1) (1)
mm
Without seals With seals
kg d D B C dk r1s min r2s min α α1 Min. Max. (2) Max. Min.
N N
140 GE 140GS GE 140GS-2RS 19.2 140 230 130 80 200 1 1 16 15 145.5 152 224.5 195 1 570 000 9 410 000
160 GE 160GS GE 160GS-2RS 25.4 160 260 135 80 225 1 1.1 16 14 165.5 180 253 221 1 770 000 10 600 000
180 GE 180GS GE 180GS-2RS 34.7 180 290 155 100 250 1.1 1.1 14 13 187 196 283 244 2 450 000 14 700 000
200 GE 200GS GE 200GS-2RS 43.8 200 320 165 100 275 1.1 1.1 15 14 207 220 313 269 2 700 000 16 200 000
220 GE 220GS GE 220GS-2RS 51.3 220 340 175 100 300 1.1 1.1 16 14 227 243.5 333 296 2 940 000 17 700 000
240 GE 240GS GE 240GS-2RS 66.1 240 370 190 110 325 1.1 1.1 15 14 247 263.5 363 320 3 510 000 21 000 000
260 GE 260GS GE 260GS-2RS 81.8 260 400 205 120 350 1.1 1.1 15 14 267 283.5 393 345 4 120 000 24 700 000
280 GE 280GS GE 280GS-2RS 97.4 280 430 210 120 375 1.1 1.1 15 14 287 310.5 423 371 4 410 000 26 500 000

Notes(1)　　Minimum allowable value of chamfer dimensions r1 and r2

 　　 (2)　　When Spherical Bushings are used with full tilting angle, the shaft shoulder dimension must be less than the maximum value of da.
Remarks1.　The inner ring and the outer ring have an oil groove and two oil holes, respectively.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
K21 1mm=0.03937inch
K22
 SPHERICAL BUSHINGS
Steel-on-steel Spherical Bushings Inch Series
B B
C C
rb rb 12° 7°

ra ra

D
D

d1
d

d1
d
dk

dk
Permissible tilting angle

SBB SBB … -2RS SBB SBB … -2RS

Shaft dia. 12.700 − 63.500mm

Identification number Mass Boundary dimensions Radial internal Mounting dimensions Dynamic load Static load
Shaft dia. (Ref.) mm(inch) clearance mm capacity capacity
(1) (1) Cd Cs
mm
Without seal With seals d D B C dk
mm
d1 ras max rbs max
(inch) kg Min./Max. Max. Max.
N N
12.700
SBB 8 ─ 0.020 12.700（ 1╱2） 22.225（   7╱8） 11.10( .437) 9.52( .375) 18 ( .709) 0.05 ／ 0.15 14.0 0.2 0.6 16 800 101 000
（ 1╱2）
15.875
SBB 10 ─ 0.036 15.875（ 5╱8） 26.988（1 1╱16） 13.89( .547) 11.91( .469) 23 ( .906) 0.05 ／ 0.15 17.9 0.2 0.8 26 900 161 000
（ 5╱8）
19.050
SBB 12 SBB 12-2RS 0.057 19.050（ 3╱4） 31.750（1 1╱4） 16.66( .656) 14.27( .562) 27.5(1.083) 0.08 ／ 0.18 21.4 0.6 *0.8 38 500 231 000
（ 3╱4）
22.225
SBB 14 SBB 14-2RS 0.088 22.225（ 7╱8） 36.512（1 7╱16） 19.43( .765) 16.66( .656) 32 (1.260) 0.08 ／ 0.18 25.0 0.6 *0.8 52 300 314 000
（ 7╱8）
25.400
SBB 16 SBB 16-2RS 0.125 25.400（1 ） 41.275（1 5╱8） 22.22( .875) 19.05( .750) 36 (1.417) 0.08 ／ 0.18 28.0 0.6 *0.8 67 300 404 000
（1）
31.750
SBB 20 SBB 20-2RS 0.234 31.750（1 1╱4） 50.800（2 ） 27.76(1.093) 23.80( .937) 45 (1.772) 0.08 ／ 0.18 35.1 0.6 0.8 105 000 630 000
（1 1╱4）
34.925
SBB 22 SBB 22-2RS 0.349 34.925（1 3╱8） 55.562（2 3╱16） 30.15(1.187) 26.19(1.031) 49 (1.929) 0.08 ／ 0.18 38.5 0.6 0.8 126 000 755 000
（1 3╱8）
38.100
SBB 24 SBB 24-2RS 0.424 38.100（1 1╱2） 61.912（2 7╱16） 33.32(1.312) 28.58(1.125) 55 (2.165) 0.08 ／ 0.18 43.3 0.6 0.8 154 000 925 000
（1 1╱2）
44.450
（1 3╱4）
SBB 28 SBB 28-2RS 0.649 44.450（1 3╱4） 71.438（2 13╱16） 38.89(1.531) 33.32(1.312) 64 (2.520) 0.08 ／ 0.18 50.4 0.6 0.8 209 000 1 250 000 K
50.800
SBB 32 SBB 32-2RS 0.939 50.800（2 ） 80.962（3 3╱16） 44.45(1.750) 38.10(1.500) 73 (2.874) 0.08 ／ 0.18 57.6 0.6 0.8 273 000 1 640 000
（2）
57.150
SBB 36 SBB 36-2RS 1.32 57.150（2 1╱4） 90.488（3 9╱16） 50.01(1.969) 42.85(1.687) 82 (3.228) 0.10 ／ 0.20 64.9 0.6 0.8 345 000 2 070 000
（2 1╱4）
63.500
SBB 40 SBB 40-2RS 1.85 63.500（2 1╱2） 100.012（3 15╱16） 55.55(2.187) 47.62(1.875) 91 (3.583) 0.10 ／ 0.20 72.0 0.6 0.8 425 000 2 550 000
（2 1╱2）

Note(1)　　 Maximum allowable corner radius of the shaft or housing

Remarks1.　The value with mark * is applicable to types without seals. For types with seals, the value is 0.4 mm.
2.　The inner ring and the outer ring have an oil groove and two oil holes, respectively.
3.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
K23 1mm=0.03937inch
K24
 SPHERICAL BUSHINGS
Steel-on-steel Spherical Bushings Inch Series
B B
C C
rb rb 12° 7°

ra ra

D
D

d1
d

d1
d
dk

dk
Permissible tilting angle

SBB SBB … -2RS SBB SBB … -2RS

Shaft dia. 69.850 − 152.400mm

Identification number Mass Boundary dimensions Radial internal Mounting dimensions Dynamic load Static load
Shaft dia. (Ref.) mm(inch) clearance mm capacity capacity
(1) (1) Cd Cs
mm
Without seal With seals d D B C dk
mm
d1 ras max rbs max
(inch) kg Min./Max. Max. Max.
N N
69.850
SBB 44 SBB 44-2RS 2.44 69.850（2 3╱4） 111.125（4 3╱8） 61.11(2.406) 52.37(2.062) 100(3.937) 0.10 ／ 0.20 79.0 0.6 0.8 514 000 3 080 000
（2 3╱4）
76.200
SBB 48 SBB 48-2RS 3.12 76.200（3 ） 120.650（4 3╱4） 66.68(2.625) 57.15(2.250) 110(4.331) 0.10 ／ 0.20 86.5 0.6 0.8 616 000 3 700 000
（3）
82.550
SBB 52 SBB 52-2RS 3.92 82.550（3 1╱4） 130.175（5 1╱8） 72.24(2.844) 61.90(2.437) 119(4.685) 0.13 ／ 0.23 94.1 0.6 0.8 722 000 4 330 000
（3 1╱4）
88.900
SBB 56 SBB 56-2RS 4.83 88.900（3 1╱2） 139.700（5 1╱2） 77.77(3.062) 66.68(2.625) 128(5.039) 0.13 ／ 0.23 101.6 0.6 0.8 837 000 5 020 000
（3 1╱2）
95.250
SBB 60 SBB 60-2RS 5.87 95.250（3 3╱4） 149.225（5 7╱8） 83.34(3.281) 71.42(2.812) 137(5.394) 0.13 ／ 0.23 108.4 0.6 0.8 960 000 5 760 000
（3 3╱4）
101.600
SBB 64 SBB 64-2RS 7.07 101.600（4 ） 158.750（6 1╱4） 88.90(3.500) 76.20(3.000) 146(5.748) 0.13 ／ 0.23 115.8 0.6 0.8 1 090 000 6 550 000
（4）
107.950
SBB 68 SBB 68-2RS 8.46 107.950（4 1╱4） 168.275（6 5╱8） 94.46(3.719) 80.95(3.187) 155(6.102) 0.13 ／ 0.23 122.6 0.8 1.1 1 230 000 7 380 000
（4 1╱4）
114.300
SBB 72 SBB 72-2RS 9.94 114.300（4 1╱2） 177.800（7 ） 100.00(3.937) 85.72(3.375) 164(6.457) 0.13 ／ 0.23 129.8 0.8 1.1 1 380 000 8 270 000
（4 1╱2）
120.650
（4 3╱4）
SBB 76 SBB 76-2RS 11.6 120.650（4 3╱4） 187.325（7 3╱8） 105.56(4.156) 90.47(3.562) 173(6.811) 0.13 ／ 0.23 136.8 0.8 1.1 1 530 000 9 210 000 K
127.000
SBB 80 SBB 80-2RS 13.5 127.000（5 ） 196.850（7 3╱4） 111.12(4.375) 95.25(3.750) 183(7.205) 0.13 ／ 0.23 144.9 0.8 1.1 1 710 000 10 300 000
（5）
152.400
SBB 96 SBB 96-2RS 17.6 152.400（6 ） 222.250（8 3╱4） 120.65(4.750) 104.78(4.125) 207(8.150) 0.13 ／ 0.23 167.5 0.8 1.1 2 130 000 12 800 000
（6）

Note(1)　　 Maximum allowable corner radius of the shaft or housing

Remarks1.　The inner ring and the outer ring have an oil groove and two oil holes, respectively.
2.　No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
K25 1mm=0.03937inch
K26
 SPHERICAL BUSHINGS
Maintenance-free Spherical Bushings
B B
C C

r2 r2

r1 r1

α α1

Da
D

da
d
α α1

dk
dk
r1 r1
r2 r2

GE … EC GE … EC-2RS
Shaft dia. 15 − 70mm

Identification number Mass Boundary dimensions Permissible Mounting dimensions Dynamic load Static load
Shaft (Ref.) mm tilting angle mm capacity capacity
degree
dia.
da Da Cd Cs
(1) (1)
mm
Without seals With seals
kg d D B C dk r1s min r2s min α α1 Min. Max. (2) Max. Min.
N N
15 GE 15EC ─ 0.032 15 26 12 9 22 0.3 0.3 8 ─ 17.5 18 23.5 21.5 19 400 48 500
17 GE 17EC ─ 0.049 17 30 14 10 25 0.3 0.3 10 ─ 19.5 20.5 27.5 24.5 24 500 61 300
20 GE 20EC ─ 0.065 20 35 16 12 29 0.3 0.3 9 ─ 22.5 24 32.5 28 34 100 85 300
25 GE 25EC ─ 0.115 25 42 20 16 35.5 0.6 0.6 7 ─ 29 29 37.5 34 55 700 139 000
30 GE 30EC GE 30EC-2RS 0.160 30 47 22 18 40.7 0.6 0.6 6 4 34 34 42.5 41.5 71 800 180 000
35 ─ GE 35EC-2RS 0.258 35 55 25 20 47 0.6 1 ─ 4 39.5 39.5 49.5 48 92 200 230 000
40 ─ GE 40EC-2RS 0.315 40 62 28 22 53 0.6 1 ─ 4 44.5 45 56.5 54.5 114 000 286 000
45 ─ GE 45EC-2RS 0.413 45 68 32 25 60 0.6 1 ─ 4 49.5 50.5 62.5 60 147 000 368 000
50 ─ GE 50EC-2RS 0.560 50 75 35 28 66 0.6 1 ─ 4 54.5 56 69.5 66 181 000 453 000
60 ─ GE 60EC-2RS    1.10 60 90 44 36 80 1 1 ─ 3 65.5 66.5 84.5 79 282 000 706 000
70 ─ GE 70EC-2RS    1.54 70 105 49 40 92 1 1 ─ 4 75.5 77.5 99.5 91 361 000 902 000

Notes(1)　Minimum allowable value of chamfer dimensions r1 and r2

 　　  (2)　When Spherical Bushings are used with full tilting angle, the shaft shoulder dimension must be less than the maximum value of da.
Remark　 No oil hole is provided.

1N=0.102kgf=0.2248lbs.
K27 1mm=0.03937inch
K28
 ■ Structure and Features Structures of lubrication type PILLOBALLs
PILLOBALLs are compact self-aligning spheri-
Outer ring
cal bushings that can support a large radial load and
a bi-directional axial load at the same time. Bushing
These bushings are classified by sliding surface (Special copper alloy)

●PILLOBALL Spherical Bushings - Insert Type types, namely, insert type, die-cast type and mainte-
nance-free type. In the insert type, a spherical inner Spherical inner ring

●PILLOBALL Rod Ends - Insert Type ring makes contact with the special copper alloy bush- (Chromium plated)

ing with superior run-in properties. In the die-cast

●PILLOBALL Rod Ends - Die-cast Type type, a spherical inner ring makes direct contact with
●PILLOBALL Rod Ends - Maintenance-free Type the bore surface of the body of special zinc die-cast
alloy. In the maintenance-free type, a spherical inner
ring makes contact with the special PTFE liner of
maintenance-free type. Thus, a smooth rotational PHS( A)
and oscillatory motion can be achieved with superior Bushing
(Special copper alloy)
anti-wear and loading properties in each type.
PILLOBALL Rod Ends have either a female thread in
the body or a male thread on the body, and they can Spherical inner ring
(Chromium plated)
be easily assembled onto machines.
Body
PILLOBALLs are used in control and link mechanisms
(Zinc chromate plated)
in machine tools, textile machines, packaging
machines, etc. The maintenance-free type is espe-
cially suitable for loading in one direction and is the
best choice for machines in which oil must be avoided
such as food processing machines, or machines
which cannot be re-lubricated. POS( A)
Spherical inner ring
(Chromium plated)
Structures of maintenance-free type PILLOBALLs Bushing
(Special copper alloy)

Special PTFE liner

(Reinforced with copper Body
alloy meshes) (Zinc chromate plated)
Spherical inner ring
(Chromium plated)

Body
(Zinc chromate plated)

Spherical inner ring

(Mirror-finished)

Spherical inner ring

(Chromium plated) K
Special PTFE liner Body
(Reinforced with copper (Special zinc die-cast alloy)
alloy meshes)

Body
(Zinc chromate plated)

K29 K30
■ Types body is zinc chromate treated and the spherical inner
ring is chromium plated on the sphere surface after
Table 4 Recommended fits
Tolerance class
In PILLOBALLs, the types shown in Table 1 are avail- heat treatment and grinding. Condition
Shaft Housing bore(1)
able. A special PTFE liner, reinforced with copper alloy
Normal operation h7 H7
meshes, which is superior in anti-wear properties with
Table 1 Type Directionally indeterminate loading n6，p6 N7
little creep deformation is used for lining on the sliding
Lubrication type Maintenance-free type surface of the body, and this type is maintenance- Note(1)　T his is applicable to PILLOBALL Spherical Bushings,
Insert type.
Type Spherical Rod end Rod end free.
Bushings female thread male thread female thread male thread PHS … EC, which has a female thread in the body,
Insert type PB PHS(…A)・PHSB POS(…A)・POSB
PHS … EC POS … EC
and POS … EC, which has a male thread on the body,
are available.
Fig. 1 Shapes of grease nipple ■ Selection of PILLOBALL
Die-cast type − PHSA −
Load capacities of PILLOBALLs are determined

Lubrication Type PILLOBALL Spherical Bushings

■ Identification number ■ Accuracy
based on the allowable contact pressure on sliding
surfaces and the strength of body for each type.
Insert Type　PB The identification number of PILLOBALLs consists of The accuracy of PILLOBALLs is shown in Tables 2 Thus, a suitable type and size should be selected
a model code, a size and any supplemental codes as and 3. The maximum radial internal clearance of the based on the dynamic load capacity C d and static
This type has superior anti-wear properties and high shown in the examples. load capacity Cs shown in the dimension tables.
insert type is 0.035 mm.
rigidity. It consists of a spherical inner ring, an outer
ring, and a bushing of special copper alloy with supe- Table 2 Tolerance unit: mm
rior run-in properties inserted in between. The spheri- Examples of identification number Load capacity
Dimension
cal surface of the inner ring is chromium plated after Type Dimension Tolerance
Example 1 symbol
heat treatment and grinding. This type is assembled   1  Dynamic load capacity
with a shaft and a housing. Supplemental Bore dia. of inner ring d H7 The dynamic load capacity C d is obtained on the
Model code Size code basis of the contact pressure on the sliding surface.
When especially large radial and/or axial loads are Outside dia. of outer ring D h6
applied, Spherical Bushings with molybdenum disul- PHSB 10 NP PB  0
The dynamic load capacity is used for calculating the
Width of inner ring B life.
fide (MoS2) treated inner and outer rings are recom- − 0.1
mended. (See page K1.) Type The dynamic load capacity considering temperature
Width of outer ring C ± 0.1
increase is obtained from the following equation using
Bore diameter PHS(…A) Bore dia. of inner ring d H7
Lubrication Type PILLOBALL Rod Ends the temperature factor, which is a correction factor for
（10/16"=15.875mm） POS(…A)
Insert Type　PHS(…A), POS(…A)，PHSB PHS … EC Width of inner ring  0 the effect of PILLOBALL temperature.
B
With grease nipple(1) POS … EC − 0.1 　　　Cdt ＝ ft Cd　……………………………………(1)
and POSB Flash type:NP
＋ 0.038 　　where,  Cdt：Dynamic load capacity considering
This type has superior wear-resistant and corrosion- Zerk type :NF Bore dia. of inner ring d
PHSB − 0.013 temperature increase,　N
resistant properties as well as high rigidity. It consists
POSB   0 　　　　　 　ft：Temperature factor (Refer to Table 5.)
of a spherical inner ring of which the spherical surface Example 2 Width of inner ring B1
Supplemental − 0.127 　　　　　 Cd ：Dynamic load capacity,　N (Refer
is chromium plated after heat treatment and grinding, Model code Size code to the dimension tables.)
a body with a zinc chromate plated outer surface, and ＋ 0.063
an inserted bushing of special copper alloy having PHS 10 EC L PHSA
Bore dia. of inner ring d
− 0.012
superior run-in properties. PHS, which has a female Width of inner ring B See Table 3. Table 5 Temperature factor　ft
Type
thread in the body, and POS, which has a male
Temperature　℃
thread on the body, are available. For PHS and POS Bore diameter
（10mm） Type − 30 ＋ 80 ＋   90 ＋ 100 ＋ 120 ＋ 150
sizes 5 to 18, an A is appended after the dimensions Table 3 Tolerance of width B of inner ring of PHSA type unit: mm
as a model code.
Left hand thread(2)
d ∆ Bs
PB
＋ 80 ＋ 90 ＋ 100 ＋ 120 ＋ 150 ＋ 180
K
Nominal bore dia. of inner ring Deviation of a single inner ring width PHS(…A)，POS(…A) 1 1 1 1 1 0.7
Lubrication Type PILLOBALL Rod Ends Over Incl. High Low PHSB，POSB
Die-cast Type　PHSA Example 3 PHS … EC
− 14 0 − 0.2 1 1 0.9 0.75 0.55 −
Model code Size POS … EC
The spherical inner ring of this type is mirror-finished 14 20 0 − 0.3
after heat treatment and is built in a body of special PB 10 20 22 0 − 0.4
zinc die-cast alloy. The sliding surfaces of the inner
  2  Static load capacity
ring and body are in close contact with each other. Type
The static load capacity Cs is the maximum static load

■ Fit
Thus, this type is an economical rod end with superior that can be applied on the PILLOBALL without break-
Bore diameter
anti-wear and loading properties. （10mm） ing the inner or outer ring of the PILLOBALL Spherical
Recommended fits for PILLOBALLs are shown in Bushing (or the inner ring or body of the PILLOBALL
Maintenance-free Type PILLOBALL Rod Ends Notes(1)　Shapes of greace nipple are shown in Fig.1. In case of Table 4. Rod End), and without causing severe permanent
PHS … EC，POS … EC
no indication of grease nipple type, grease nipple is not
prepared. deformation that will make the PILLOBALL unusable.
(2)　Right hand thread is indicated with no code.
This type has superior anti-corrosion properties as the
1N=0.102kgf=0.2248lbs.
K31 1mm=0.03937inch
K32
Maximum Operating Load As the actual life is affected by many factors such as
the material of the sliding surface, the magnitude and
8
The recommended value of bushing load is obtained direction of load, lubrication, sliding velocity, etc., the
5
by multiplying the dynamic load capacity C d by a calculated life can be used as a measure of expected 4
3 ate
numerical factor, which differs depending on the service life. ern
2 Alt
bushing type and load condition. For PILLOBALL Rod ion

Sliding velocity factor b 3

ect
dir
Ends, the static load capacity Cs must also be con-   1  Life of lubrication type PILLOBALLs 1
oa
d

nt
L

ta
PB・PHS(…A)・POS(…A)・PHSB・POSB

ns
sidered in determining the applicable bushing load.

Co
0.5
Table 6 shows the guidelines for maximum operating ［1］Confirmation of pV value 0.4

on
cti
0.3
β β

re
load of PILLOBALLs. When axial loads are added in Before attempting to calculate the life, make sure that

di
0.2

ad
addition to radial loads, bending stress occurs in the the operating conditions are within the permissible Oscillating angle

Lo
β β 0.1
body. Pay attention to this bending stress. range by referring to the pV diagram in Fig.2.
Oscillating angle 0.05
When the operating conditions are out of the permis-
0.2 0.5 1 5 10 50 100 150
Table 6 Maximum operating load sible range, please consult .
Sliding velocity V mm/s
Load direction The contact pressure p and the sliding velocity V are
Type
Constant Alternate obtained from the following equations.
Fig. 3 Oscillating angle Fig. 4 Sliding velocity factor for lubrication type
 50P 
PB ≦ 0.3Cd ≦ 0.6Cd p＝  ………………………………………(3) PILLOBALLs
≦ 0.3Cd    ≦ 0.2Cs
　　　　Cdt
PHS(…A)，POS(…A)，PHSB，POSB
V ＝ 5.82 × 10 − 4dk β f    ……………………(4) ［2］Life calculation
PHSA ≦ 0.16Cs
　　where,　p：Contact pressure,　N/mm2
PHS … EC，POS … EC ≦ 0.3Cs ≦ 0.2Cs The life of lubrication type PILLOBALLs can be calcu-   2  Life of maintenance-free type PILLOBALLs　PHS … EC・POS … EC
　　　　　　P：Equivalent radial load,　N lated by the following equations. ［1］Confirmation of pV value
Remark　Cd is the dynamic load capacity and Cs is the static load
capacity.
(Refer to equation (2).) Before attempting to calculate the life, make sure that
3.18b1b2b3 Cdt 2 
　　　　　 Cdt：Dynamic load capacity considering
temperature increase,　N
　　　G ＝  
　　　　　　 d
√￣￣k β　        P （　   ）
　  　 ×105  ……………(5) the operating conditions are within the permissible
range by referring to the pV diagram in Fig.5.
Equivalent radial load (Refer to equation (1).) G When the operating conditions are out of the permis-
　　　Lh ＝     　  ……………………………………(6)
　　　　　　V：Sliding velocity,　mm/s    60f sible range, please consult .
　　　　   
PILLOBALLs can take radial and axial loads at the The contact pressure p and sliding velocity V are
　　　　　dk：Sphere diameter,　mm 　　where, G：Life (Total number of oscillations)
same time. When the magnitude and direction of obtained from equations (3) and (4) on page K6.
(Refer to the dimensional tables.) 　　　　　 b1：Load directional factor (Refer to Table 8.)
loads are constant, the equivalent radial load can be
　　　　　2β：Oscillating angle degrees (Refer to Fig.3.) 　　　　　 b2：Lubrication factor (Refer to Table 8.)
obtained by the following equation.
　　　　　　　　when β＜ 5° , β＝ 5 　　　　　 b3：Sliding velocity factor (Refer to Fig. 4.)
　　　P ＝ Fr ＋ YFa…………………………………(2)
　　　　　　　　when rotating,　β ＝ 90 　　　　　Cdt：Dynamic load capacity considering
　　where,　P：Equivalent radial load,　N
　　　　　 f ：Number of oscillations per minute, min-1 temperature increase,　N 80
　　　　　 Fr：Radial load,　N 60
　　　　　 Fa：Axial load,　N (Refer to equation (1).)
40
　　　　　 Y：Axial load factor (Refer to Table 7.) 　　　　　 P：Equivalent radial load,　N

N / mm 2
 (Refer to equation (2).) 20

Table 7 Axial load factor　Y 60 　　　　　 Lh：Life in hours,　h Permissible range

10
Fa ／ Fr 40 　　　　　 f ：Number of oscillations per minute, min-1

p
8
0.1 0.2 0.3 0.4 0.5 ＞ 0.5 6

Contact pressure
Type
20 4
N /mm 2

PB Table 8 Load directional factor b1 and lubrication

PHS(…A)，POS(…A)
PHSB，POSB
1 2 3 4 5 Unusable 10
8
Permissible range
factor b2 for lubrication type PILLOBALLs 2 K
Load directional factor　b1 Lubrication factor　b2
p

6
PHS … EC 1
Contact pressure

Unusable 4 Load direction Periodical lubrication 1 2 5 10 20 50 100 200

1 2 3
POS … EC
Constant Alternate None Regular Sliding velocity V mm / s
2
1 5 1 15 Fig. 5 pV diagram for maintenance-free type
Life 1
PILLOBALL Rod Ends
1 2 5 10 20 50 100 200
The life of PILLOBALLs is defined as the total number
Sliding velocity V mm / s
of oscillating motions during which the PILLOBALLs
can be operated without failure or malfunction due to
wear, increase in internal clearance, increase in slid-
Fig. 2 pV diagram of lubrication type PILLOBALLs
ing torque and operating temperature, etc.

1N=0.102kgf=0.2248lbs.
K33 1mm=0.03937inch
K34
［2］Life calculation
The life of maintenance-free type PILLOBALL Rod
■ Oil Hole and Grease Nipple ■ Operating Temperature Range Table 12 Allowable tilting angle

Ends is obtained from the total sliding distance S Table 10 shows the specifications of oil hole and The maximum allowable temperature for Lubrication
which is given in Fig.5 for the contact pressure p grease nipple on the outer ring or body. Further, type PILLOBALLs is +180゜ C for the insert type and α1
α2
obtained from equation (3). lubrication nozzle models compatible with the grease +80゜ C for the die-cast type.
The total number of oscillations and life in hours can nipple are shown in Table 11. The maximum allowable temperature for Maintenance-
be obtained from the following equations. For PILLOBALLs without an oil hole and grease nip- free type PILLOBALL Rod Ends is +150゜ C.
　　 ple, apply grease directly on the spherical surface.
Sf
　　　G ＝ 16.67 × b1 ×      ………………………(7)
　　　　　　
G
　       V
Table 10 Specifications of oil hole and grease nipple ■ Precautions for Use
　　　Lh＝     　  ……………………………………(8)
   60f Type   1  Tightening depth
　　　　    Specification The recommended tightening depth of the screw into
Bore diameter of inner ring unit: degree
　　where,　G：Life (Total number of oscillations) the PILLOBALL Rod End body is shown below.
  d mm
　　　　　　b1：L oad directional factor (Refer to d PB(1)，PHS(…A)，POS(…A)
PB 1 oil hole + oil groove Insert type and maintenance-free type: 1.25 times the  PHSA
Table 9.) Bore diameter PHS … EC，POS … EC
nominal thread dia. or more.
　   d ≦ 4 None mm α1 α2 α1 α2
　　　　　　 S：Total sliding distance　m PHS(…A) Die-cast type: 2 times the nominal thread dia. or
4＜d With grease nipple
　　　　　 　f：Number of oscillations per minute　min -1
more.   3   7 13 − −
　　　　　　 V：Sliding velocity　mm/s
　   d ≦ 4 None
  4   7 13 − −
POS(…A) 4＜d≦6 1 oil hole
　　　　　   Lh：Life in hours　h   2  Allowable tilting angle   5   8 13 7 13
6＜d With grease nipple The allowable tilting angle differs depending on the
  6   8 13 7 13
PHSB・POSB None(1) mounting structure as shown in Table 12 and Table 13.
Table 9 Load directional factor for maintenance-free type PILLOBALLs  b1   8   8 14 8 14
PHSA With grease nipple
10   8 14 8 14
Load direction Constant Alternate PHS … EC，POS … EC None
12   8 13 8 13
Note(1)　Grease Nipple is available for size 4 or larger with sup-
14 10 16 9 16
Load directional factor　b1 1 0.2(1) plemental code.

Note(1)　This value is applicable when the load changes compara-

16   9 15 9 15
tively slowly. When the load changes rapidly, please con- Table 11 Types and Dimension of Lubrication Nozzles 18   9 15 9 15
sult , as the factor degreases sharply.
Type Dimension 20   9 15 9 15
22 10 15 9 15
25   9 15 − −
A-5126T 28   9 15 − −
p N /mm 2

50
40 30 10 17 − −
30 Note(1)　In the case of the PB series, α2 is applicable in general.
20
Contact pressure

10
0 Table 13 Allowable tilting angle for inch series
10 20 50 100 200 500 1000 × 10 3 unit: degree
Total sliding distance S m A-5120R
With female With male α1 α2
thread thread
Fig. 6 Contact pressure and total sliding distance for

K
maintenance-free type PILLOBALL Rod Ends PHSB 2 POSB 2 8 16
PHSB 2.5 POSB 2.5 7 12
PHSB 3 POSB 3 6 10

■ Lubrication B-5120R PHSB 4

PHSB 5
POSB 4
POSB 5
7
6
13
10
Maintenance-free type PILLOBALL Rod Ends have a
PHSB 6 POSB 6 6 11
sliding surface lined with a self-lubricating lining.
Remark　HSP-3(Yamada Corporation)can be used for them. PHSB 7 POSB 7 7 11
Therefore, they can be used without lubrication. The above nozzles can be atached on the standard
Lubrication type PILLOBALLs are not provided with grease gun shown below. PHSB 8 POSB 8 6   9
prepacked grease. Perform proper lubrication for Body of grease gun
PHSB 10 POSB 10 7 11
use. Operating without lubrication will increase the Lubrication Nozzle PHSB 12 POSB 12 6 10
wear of the sliding contact surfaces and cause PHSB 16 POSB 16 7 14
seizure.

1N=0.102kgf=0.2248lbs.
K35 1mm=0.03937inch
K36
 PILLOBALL
Lubrication Type PILLOBALL Spherical Bushings Insert Type Lubrication Type PILLOBALL Rod Ends Insert Type/With Female Thread
B
B
d2 C1
C

r1
r2

d1

d
r1

r1

l4
d3

h1
d1
D

l3
r1

l5
r2 dL G
W

PB PHS(…A)

Mass Boundary dimensions　mm Dynamic load Static load Mass Boundary dimensions　mm Dynamic load Static load
(Ref.) capacity capacity capacity capacity
Identification Identification (Ref.)
number Ball dia. Cd Cs number Thread Cd Cs
(1) (1) Ball dia.
g d D C B d1 rs min mm
g d G d2 C1 B d1 l4 h1 l3 l5 W d3 dL r1smin mm
(inch) N N (inch) N N
11.112   7.938
PB 5 8.5 5 16 6 8 7.7 0.2 3 270 7 850 PHS 3 5.7 3 M 3×0.5 12 4.5 6 5.2 27 21 10 3 5.5 5 6.5 0.2 1 750 3 670
（  7╱16） （  5╱16）
12.700   9.525
PB 6 13 6 18 6.75 9 9 0.2 4 200 10 100 PHS 4 11.9 4 M 4×0.7 14 5.3 7 6.5 31 24 12 4 8 8 9.5 0.2 2 480 4 680
（  1╱2） （  3╱8）
15.875 11.112
PB 8 24 8 22 9 12 10.4 0.2 7 010 16 800 PHS 5A 16.5 5 M 5×0.8 16 6 8 7.7 35 27 14 4 9 9 11 0.2 3 270 5 730
（  5╱8） （  7╱16）
19.050 12.700
PB 10 39 10 26 10.5 14 12.9 0.2 9 810 23 500 PHS 6A 25 6 M 6×1 18 6.75 9 9 39 30 14 5 11 10 13 0.2 4 200 6 910
（  3╱4） （  1╱2）
22.225 15.875
PB 12 58 12 30 12 16 15.4 0.2 13 100 31 400 PHS 8A 43 8 M 8×1.25 22 9 12 10.4 47 36 17 5 14 12.5 16 0.2 7 010 10 200
（  7╱8） （  5╱8）
25.400 19.050
PB 14 84 14 34 13.5 19 16.9 0.3 16 800 40 400 PHS 10A 72 10 M10×1.5 26 10.5 14 12.9 56 43 21 6.5 17 15 19 0.2 9 810 13 300
（1 ） （  3╱4）
28.575 22.225
PB 16 111 16 38 15 21 19.4 0.3 21 000 50 400 PHS 12A 107 12 M12×1.75 30 12 16 15.4 65 50 24 6.5 19 17.5 22 0.2 13 100 16 900
（1 1╱8） （  7╱8）
31.750 25.400
PB 18 160 18 42 16.5 23 21.9 0.3 25 700 61 600 PHS 14A 160 14 M14×2 34 13.5 19 16.9 74 57 27 8 22 20 25 0.2 16 800 20 900
（1 1╱4） （1 ）
34.925 28.575
PB 20 210 20 46 18 25 24.4 0.3 30 800 74 000 PHS 16A 210 16 M16×2 38 15 21 19.4 83 64 33 8 22 22 27 0.2 21 000 25 400
（1 3╱8） （1 1╱8）
38.100 31.750
PB 22 265 22 50 20 28 25.8 0.3 37 400 89 700 PHS 18A 295 18 M18×1.5 42 16.5 23 21.9 92 71 36 10 27 25 31 0.2 25 700 30 200
（1 1╱2） （1 1╱4）

PB 25 390 25 56 22 31 29.6 0.6

42.862
（1 11╱16）
46 200 111 000 PHS 20 380 20 M20×1.5 46 18 25 24.4 100 77 40 10 30 27.5 34 0.2
34.925
（1 3╱8）
30 800 35 500 K
47.625 38.100
PB 28 410 28 62 25 35 32.3 0.6 58 400 140 000 PHS 22 490 22 M22×1.5 50 20 28 25.8 109 84 43 12 32 30 37 0.2 37 400 41 700
（1 7╱8） （1 1╱2）
50.800 42.862
PB 30 610 30 66 25 37 34.8 0.6 62 300 149 000 PHS 25 750 25 M24×2 60 22 31 29.6 124 94 48 12 36 33.5 42 0.6 46 200 72 700
（2 ） （1 11╱16）
47.625
PHS 28 950 28 M27×2 66 25 35 32.3 136 103 53 12 41 37 46 0.6 58 400 87 000
（1 7╱8）
50.800
PHS 30 1 130 30 M30×2 70 25 37 34.8 145 110 56 15 41 40 50 0.6 62 300 92 200
（2 ）
Note(1)　　 Minimum allowable value of chamfer dimensions r1 and r2 Note(1)　　 Minimum allowable value of chamfer dimension r1
Remarks1.   The outer ring has an oil groove and an oil hole. Remarks1.   Neither oil hole nor grease nipple is provided for PHS with an inner ring bore diameter d of 4 mm or less.
2.   No grease is prepacked. Perform proper lubrication. 　　　　　   For others, a grease nipple is provided on the body.
2.   No grease is prepacked. Perform proper lubrication.
3.  When a metric fine thread specification for inner ring bore deameter d of 8 mm to 14 mm is required, please contact .
　　　　　　　

1N=0.102kgf=0.2248lbs.
K37 1mm=0.03937inch
K38
 PILLOBALL
Lubrication Type PILLOBALL Rod Ends Insert Type/With Male Thread Inch series PILLOBALL Rod Ends Insert Type/With Female Thread
B B1
d2 C1 D B

r1
r

d1

d
r1

d1
r

d
l2

L
h
D1

L1
l1

L2
l
G
D2 S
W
POS(…A)
PHSB

Mass Boundary dimensions　mm Dynamic load Static load Mass Boundary dimensions Dynamic Static
capacity capacity mm(inch) load load
Identification (Ref.) Identification (Ref.) capacity capacity
number Thread Cd Cs number Thread Ball dia. Cd Cs
(1) Ball dia. (1) mm
g d G d2 C1 B d1 l2 h l1 r1s min mm
g d S D B B1 d1 L l L1 L2 W D1 D2 rsmin
(inch) N N class 3B (inch) N N
  7.938 3.175 -32UNC 11.91 4.75 6.35 4.75 26.57 4.75 20.62 9.53 6.35 6.35 7.92 0.3 7.938
POS 3 5.0   3 M 3×0.5 12 4.5 6 5.2 33 27 15 0.2 1 750 1 220
（  5╱16） PHSB 2 6.8
( .1250) ( .1380) ( .469) ( .187) ( .250) ( .187) (1.046) ( .187) ( .812) ( .375) ( .250) ( .250) ( .312) ( .012) （  5╱16）
1 850 5 840
  9.525
POS 4 8.1   4 M 4×0.7 14 5.3 7 6.5 37 30 17 0.2 2 480 2 060
（  3╱8） 3.967 -32UNC 14.27 5.56 7.14 6.32 29.36 4.75 22.23 9.53 7.14 7.14 8.74 0.3 9.525
PHSB 2.5 11 ( .1562) ( .1640) ( .562) ( .219) ( .281) ( .249) (1.156) ( .187) ( .875) ( .375) ( .281) ( .281) ( .344) ( .012) （  3╱8） 2 600 8 210
11.112
POS 5A 12.5   5 M 5×0.8 16 6 8 7.7 41 33 20 0.2 3 270 3 340
（  7╱16）
4.826 -32UNF 15.88 6.35 7.92 7.77 34.93 4.75 26.97 14.27 7.92 7.92 10.31 0.3 11.112
12.700 PHSB 3 14 ( .1900) ( .1900) ( .625) ( .250) ( .312) ( .306) (1.375) ( .187) (1.062) ( .562) ( .312) ( .312) ( .406) ( .012) （  7╱16）
3 460 9 090
POS 6A 19   6 M 6×1 18 6.75 9 9 45 36 22 0.2 4 200 4 730
（  1╱2）
15.875 6.350 -28UNF 19.05 7.14 9.53 9.02 42.85 4.75 33.32 19.05 9.53 9.53 11.89 0.5 13.097
POS 8A 32   8 M 8×1.25 22 9 12 10.4 53 42 25 0.2 7 010 8 640 PHSB 4 23 4 590 13 200
（  5╱8） ( .2500) ( .2500) ( .750) ( .281) ( .375) ( .355) (1.687) ( .187) (1.312) ( .750) ( .375) ( .375) ( .468) ( .020) （ 33╱64）
19.050
POS 10A 54 10 M10×1.5 26 10.5 14 12.9 61 48 29 0.2 9 810 13 300 7.938 -24UNF 22.23 8.74 11.10 11.35 46.02 4.75 34.93 19.05 11.10 11.10 12.70 0.5 15.875
（  3╱4） PHSB 5 36 16 500
 5╱8） 6 800
( .3125) ( .3125) ( .875) ( .344) ( .437) ( .447) (1.812) ( .187) (1.375) ( .750) ( .437) ( .437) ( .500) ( .020) （
22.225
POS 12A 85 12 M12×1.75 30 12 16 15.4 69 54 33 0.2 13 100 16 900
（  7╱8） 9.525 -24UNF 25.40 10.31 12.70 13.13 53.98 6.35 41.28 23.80 14.27 14.27 17.45 0.5 18.256
25.400 PHSB 6 59 ( .3750) ( .3750) (1.000) ( .406) ( .500) ( .517) (2.125) ( .250) (1.625) ( .937) ( .562) ( .562) ( .687) ( .020) （ 23╱32）
9 230 21 600
POS 14A 126 14 M14×2 34 13.5 19 16.9 77 60 36 0.2 16 800 20 900
（1 ）
28.575 11.112 -20UNF 28.58 11.10 14.27 14.88 60.33 6.35 46.02 26.97 15.88 15.88 19.05 0.5 20.638
POS 16A 185 16 M16×2 38 15 21 19.4 85 66 40 0.2 21 000 25 400 PHSB 7 82 ( .4375) ( .4375) (1.125) ( .437) ( .562) ( .586) (2.375) ( .250) (1.812) (1.062) ( .625) ( .625) ( .750) ( .020) 13╱ 11 200 26 100
（1 1╱8） （ 16）
31.750
POS 18A 260 18 M18×1.5 42 16.5 23 21.9 93 72 44 0.2 25 700 30 200 12.700 -20UNF 33.32 12.70 15.88 17.73 70.64 6.35 53.98 30.15 19.05 19.05 22.23 0.5 23.812
（1 1╱4） PHSB 8 132 ( .5000) ( .5000) (1.312) ( .500) ( .625) ( .698) (2.781) ( .250) (2.125) (1.187) ( .750) ( .750) ( .875) ( .020) （ 15╱16）
14 800 36 200

POS 20 340 20 M20×1.5 46 18 25 24.4 101 78 47 0.2

34.925
（1 3╱8）
30 800 35 500
15.875 -18UNF 38.10 14.27 19.05 21.31 82.55 7.92 63.50 38.10 22.23 22.23 25.40 0.5 28.575
K
PHSB 10 191 ( .6250) ( .6250) (1.500) ( .562) ( .750) ( .839) (3.250) ( .312) (2.500) (1.500) ( .875) ( .875) (1.000) ( .020) 1╱ 20 000 39 300
38.100 （1 8）
POS 22 435 22 M22×1.5 50 20 28 25.8 109 84 51 0.2 37 400 41 700
（1 1╱2）
19.050 -16UNF 44.45 17.45 22.23 24.84 95.25 7.92 73.03 44.45 25.40 25.40 28.58 0.5 33.338
42.862 PHSB 12 286 ( .7500) ( .7500) (1.750) ( .687) ( .875) ( .978) (3.750) ( .312) (2.875) (1.750) (1.000) (1.000) (1.125) ( .020) （1 5╱16）
28 500 55 000
POS 25 650 25 M24×2 60 22 31 29.6 124 94 57 0.6 46 200 72 700
（1 11╱16）
47.625 25.400 -12UNF 69.85 25.40 34.93 32.23 139.70 11.07 104.78 53.98 38.10 38.10 44.45 0.5 47.625
POS 28 875 28 M27×2 66 25 35 32.3 136 103 62 0.6 58 400 87 000 PHSB 16 998 59 300 86 800
（1 7╱8） (1.0000) (1.2500) (2.750) (1.000) (1.375) (1.269) (5.500) ( .436) (4.125) (2.125) (1.500) (1.500) (1.750) ( .020) （1 7╱8）
50.800
POS 30 1 070 30 M30×2 70 25 37 34.8 145 110 66 0.6 62 300 92 200
（2 ）
Note(1)　　 Minimum allowable value of chamfer dimension r1 Note(1)　 rs min stands for minimum allowable value of chamfer r.
Remarks1.   Neither oil hole nor grease nipple is provided for POS with an inner ring bore diameter d of 4 mm or less. Remark   No grease is prepacked. Perform proper lubrication.
　　　　　   For those with an inner ring bore diameter d of 5 to 6 mm, an oil hole is provided on the body. For others, a grease nipple is
provided on the body.
2.   No grease is prepacked. Perform proper lubrication.
3.  When a metric fine thread specification for inner ring bore deameter d of 8 mm to 14 mm is required, please contact .
　　　　　　　

1N=0.102kgf=0.2248lbs.
K39 1mm=0.03937inch
K40
 PILLOBALL
Inch series PILLOBALL Rod Ends Insert Type/With Male Thread Lubrication Type PILLOBALL Rod Ends Die-cast Type/With Female Thread
B
B1 d2 C1
D B

r1
r

d1

d
r1

d1

d
r

l4
d3

h1
L
L1

l3
L2

l5
dL G
W
S

POSB PHSA

Mass Boundary dimensions Dynamic Static Mass Boundary dimensions　mm Static load
mm(inch) load load capacity
Identification (Ref.) capacity capacity Identification (Ref.)
number Thread Ball dia. Cd Cs number Thread Cs
(1) (1) Ball dia.
g d S D B B1 d1 L L1 L2 rs min mm
g d G d2 C1 B d1 l4 h1 l3 l5 W d3 dL r1s min mm
class 3A (inch) N N (inch) N

7.938 11.112
3.175 -32UNC 11.91 4.75 6.35 4.75 29.77 23.80 12.70 0.3 PHSA 5 17 5 M 5×0.8 17 6 8 7.7 35.5 27 16 4 9 9 11 0.2 5 470
POSB 2 5.4
( .1250) ( .1380) ( .469) ( .187) ( .250) ( .187) (1.172) ( .937) ( .500) ( .012) （  5╱16）
1 850 2 160 （  7╱16）
12.700
3.967 -32UNC 14.27 5.56 7.14 6.32 35.71 28.58 15.88 0.39.525 PHSA 6 25 6 M 6×1 19.5 6.75 9 9 39.7 30 16 5 11 10 13 0.2
（  1╱2）
6 760
POSB 2.5 9.1
( .1562) ( .1640) ( .562) ( .219) ( .281) ( .249) (1.406) (1.125) ( .625) ( .012) （  3╱8）
2 600 3 370
15.875
PHSA 8 45 8 M 8×1.25 24 9 12 10.4 48 36 19 5 14 12.5 16 0.2
（  5╱8）
10 200
4.826 -32UNF 15.88 6.35 7.92 7.77 39.70 31.75 19.05 0.3 11.112
POSB 3 14
( .1900) ( .1900) ( .625) ( .250) ( .312) ( .306) (1.563) (1.250) ( .750) ( .012) （  7╱16）
3 460 4 850 19.050
PHSA 10 70 10 M10×1.5 28 10.5 14 12.9 57 43 23 6.5 17 15 19 0.2
（  3╱4）
13 100
6.350 -28UNF 19.05 7.14 9.53 9.02 49.20 39.67 25.40 0.5 13.097 22.225
POSB 4 23 4 590 8 870 PHSA 12 105 12 M12×1.75 32 12 16 15.4 66 50 27 6.5 19 17.5 22 0.2
（  7╱8）
16 400
( .2500) ( .2500) ( .750) ( .281) ( .375) ( .355) (1.937) (1.562) (1.000) ( .020) （ 33╱64）
25.400
7.938 -24UNF 22.23 8.74 11.10 11.35 58.72 47.63 31.75 0.5 15.875 PHSA 14 155 14 M14×2 36 13.5 19 16.9 75 57 30 8 22 20 25 0.3
（1 ）
20 000
POSB 5 36
( .3125) ( .3125) ( .875) ( .344) ( .437) ( .447) (2.312) (1.875) (1.250) ( .020) （  5╱8）
6 800 14 200
28.575
PHSA 16 190 16 M16×2 40 15 21 19.4 84 64 36 8 22 22 27 0.3
（1 1╱8）
23 900
9.525 -24UNF 25.40 10.31 12.70 13.13 61.93 49.23 31.75 0.5 18.256
POSB 6 54
( .3750) ( .3750) (1.000) ( .406) ( .500) ( .517) (2.438) (1.938) (1.250) ( .020) （ 23╱32）
9 230 21 600 31.750
PHSA 18 290 18 M18×1.5 45 16.5 23 21.9 93.5 71 40 10 27 25 31 0.3
（1 1╱4）
28 800
11.112 -20UNF 28.58 11.10 14.27 14.88 68.28 53.98 34.93 0.5 20.638 34.925
POSB 7 77
( .4375) ( .4375) (1.125) ( .437) ( .562) ( .586) (2.688) (2.125) (1.375) ( .020) （ 13╱16）
11 200 26 100 PHSA 20 400 20 M20×1.5 49 18 25 24.4 101.5 77 43 10 30 27.5 34 0.3 33 400
（1 3╱8）
38.100
12.700 -20UNF 33.32 12.70 15.88 17.73 78.59 61.93 38.10 0.5 23.812 PHSA 22 500 22 M22×1.5 54 20 28 25.8 111 84 47 12 32 30 37 0.3 40 400
POSB 8 122 14 800 36 200 （1 1╱2）
( .5000) ( .5000) (1.312) ( .500) ( .625) ( .698) (3.094) (2.438) (1.500) ( .020) （ 15╱16）

15.875 -18UNF 38.10 14.27 19.05 21.31 85.73 66.68 41.28 0.5 28.575
K
POSB 10 186
( .6250) ( .6250) (1.500) ( .562) ( .750) ( .839) (3.375) (2.625) (1.625) ( .020) （1 1╱8）
20 000 39 300

19.050 -16UNF 44.45 17.45 22.23 24.84 95.25 73.03 44.45 0.5 33.338
POSB 12 295
( .7500) ( .7500) (1.750) ( .687) ( .875) ( .978) (3.750) (2.875) (1.750) ( .020) （1 5╱16）
28 500 55 000

25.400 -12UNF 69.85 25.40 34.93 32.23 139.70 104.78 53.98 0.5 47.625
POSB 16 1 129 (1.0000) (1.2500) (2.750) (1.000) (1.375) (1.269) (5.500) (4.125) (2.125) ( .020) （1 7╱8）
59 300 112 000

Note(1)　 rs min stands for minimum allowable value of chamfer r. Note(1)　　 Minimum allowable value of chamfer dimension r1
Remark   No grease is prepacked. Perform proper lubrication. Remarks1.   A grease nipple is provided on the body.
2.   No grease is prepacked. Perform proper lubrication.
3.  When a metric fine thread specification for inner ring bore deameter d of 8 mm to 14 mm is required, please contact .　　　　
　　

1N=0.102kgf=0.2248lbs.
K41 1mm=0.03937inch
K42
 PILLOBALL
Maintenance-free Type PILLOBALL Rod Ends With Female Thread Maintenance-free Type PILLOBALL Rod Ends With Male Thread
B B
d2 C1 d2 C1

r1 r1

d1

d1
d

d
r1 r1

l2
l4
d3

h1

l1
l3
l5
dL G
G
W

PHS … EC POS … EC

Mass Boundary dimensions　mm Dynamic load Static load Mass Boundary dimensions　mm Dynamic load Static load
capacity capacity capacity capacity
Identification (Ref.) Identification (Ref.)
number Thread Cd Cs number Thread Cd Cs
(1) Ball dia. (1) Ball dia.
g d G d2 C1 B d1 l4 h1 l3 l5 W d3 dL r1s min mm g d G d2 C1 B d1 l2 h l1 r1s min mm
(inch) N N (inch) N N
  7.938   7.938
PHS 3EC 5.7 3 M 3×0.5 12 4.5 6 5.2 27 21 10 3 5.5 5 6.5 0.2 3 500 2 480 POS 3EC   5.0 3 M 3×0.5 12 4.5 6 5.2 33 27 15 0.2 3 500 1 220
（  5╱16） （  5╱16）
  9.525   9.525
PHS 4EC 11.9 4 M 4×0.7 14 5.3 7 6.5 31 24 12 4 8 8 9.5 0.2 4 950 3 260 POS 4EC   8.1 4 M 4×0.7 14 5.3 7 6.5 37 30 17 0.2 4 950 2 060
（  3╱8） （  3╱8）
11.112 11.112
PHS 5EC 16.5 5 M 5×0.8 16 6 8 7.7 35 27 12.5 4 9 9 11 0.2 6 540 4 010 POS 5EC 12.5 5 M 5×0.8 16 6 8 7.7 41 33 20 0.2 6 540 3 340
（  7╱16） （  7╱16）
12.700 12.700
PHS 6EC 25 6 M 6×1 18 6.75 9 9 39 30 13.5 5 11 10 13 0.2 8 410 4 940 POS 6EC 19 6 M 6×1 18 6.75 9 9 45 36 22 0.2 8 410 4 730
（  1╱2） （  1╱2）
15.875 15.875
PHS 8EC 43 8 M 8×1.25 22 9 12 10.4 47 36 16 5 14 12.5 16 0.2 14 000 7 760 POS 8EC 32 8 M 8×1.25 22 9 12 10.4 53 42 25 0.2 14 000 7 760
（  5╱8） （  5╱8）
19.050 19.050
PHS 10EC 72 10 M10×1.5 26 10.5 14 12.9 56 43 19.5 6.5 17 15 19 0.2 19 600 10 500 POS 10EC 54 10 M10×1.5 26 10.5 14 12.9 61 48 29 0.2 19 600 10 500
（  3╱4） （  3╱4）
22.225 22.225
PHS 12EC 107 12 M12×1.75 30 12 16 15.4 65 50 24 6.5 19 17.5 22 0.2 26 200 13 700 POS 12EC 85 12 M12×1.75 30 12 16 15.4 69 54 33 0.2 26 200 13 700
（  7╱8） （  7╱8）
25.400 25.400
PHS 14EC 160 14 M14×2 34 13.5 19 16.9 74 57 27 8 22 20 25 0.2 33 600 17 200 POS 14EC 126 14 M14×2 34 13.5 19 16.9 77 60 36 0.2 33 600 17 200
（1 ） （1 ）
28.575 28.575
PHS 16EC 210 16 M16×2 38 15 21 19.4 83 64 33 8 22 22 27 0.2 42 000 21 100 POS 16EC 185 16 M16×2 38 15 21 19.4 85 66 40 0.2 42 000 21 100
（1 1╱8） （1 1╱8）
31.750 31.750
PHS 18EC 295 18 M18×1.5 42 16.5 23 21.9 92 71 36 10 27 25 31 0.2 51 400 25 100 POS 18EC 260 18 M18×1.5 42 16.5 23 21.9 93 72 44 0.2 51 400 25 100
（1 1╱4） （1 1╱4）

PHS 20EC 380 20 M20×1.5 46 18 25 24.4 100 77 40 10 30 27.5 34 0.2

34.925
（1 3╱8）
61 600 30 000 POS 20EC 340 20 M20×1.5 46 18 25 24.4 101 78 47 0.2
34.925
（1 3╱8）
61 600 30 000 K
38.100 38.100
PHS 22EC 490 22 M22×1.5 50 20 28 25.8 109 84 41 12 32 30 37 0.2 74 700 36 400 POS 22EC 435 22 M22×1.5 50 20 28 25.8 109 84 51 0.2 74 700 36 400
（1 1╱2） （1 1╱2）

Note(1)　　 Minimum allowable value of chamfer dimension r1 Note(1)　　 Minimum allowable value of chamfer dimension r1
Remarks1.   Neither oil hole nor grease nipple is provided. Remarks1.   Neither oil hole nor grease nipple is provided.
2.   When a metric fine thread specification for inner ring bore deameter d of 8 mm to 14 mm is required, please contact . 2.   When a metric fine thread specification for inner ring bore deameter d of 8 mm to 14 mm is required, please contact .

1N=0.102kgf=0.2248lbs.
K43 1mm=0.03937inch
K44
 ■ Structure and Features Structures of L-Ball LHSA
L-Balls are self-aligning rod-ends consisting of
Body
a special zinc die-cast alloy body and a studded ball
which has its axis at right angles to the body. Ball-stud
They can perform tilting movement, oscillating move-

●L-Balls ment and rotation with low torque, and transmit power
smoothly due to uniform clearance between the slid-
●L-Ball Dust Cover ing surfaces. Bushing
Their superior wear resistance assures stable accura- (Low carbon steel)
cy for long periods of time, and maintenance is sim-
ple. They are very economical bearings.
For these reasons, they are widely used in link mech- Body

anisms in automobiles, construction machinery, farm Ball-stud

and packaging machines, etc.

■ Types
Dust cover

Bushing
(Copper alloy)
L-Balls are available in various types as shown in
Table 1.
and upwards
Table 1 Type of L-Balls Body
Ball-stud
L-Ball dust
Type L-Ball
cover

Model code LHSA LHS PRC

L-Ball LHSA Dust cover Bushing

These are compact rod-ends in which the spherical (Fixed to the body) (Copper alloy)
part of the ball-stud are held by the special zinc die-
cast alloy body. There is a dust cover on the stud
side and good quality lithium soap base grease is pre-
packed. They can be run for long periods of time
without re-lubrication and have excellent lubrication Structure of L-Ball LHS
and anti-dust properties.
As shown in the structural drawing, these rod-ends Body
are classified into 3 types by size. In addition, the
ball-studs of LHSA 10 and lower are formed in one

K
solid body, but those of LHSA 12 and higher, which
are used under large loads, have the stud friction-
welded to a high precision steel ball to give greater
resistance to wear.
Ball-stud
L-Ball LHS
These rod-ends have a friction-welded ball-stud, and
a special zinc die-cast alloy body which houses the
spherical surface of the high precision steel ball.
There is an almost complete contact across the slid- base grease, they have excellent lubrication and anti-
ing surfaces, and the uniform clearance guarantees a dust properties and can run for long periods of time
stable bearing life. without re-lubrication.
An L-Ball dust cover can be attached to these rod- When the L-Ball LHS is delivered with a dust cover on
ends. If the rod-ends are lubricated with lithium soap request, lithium soap base grease is prepacked.

K45 K46
L-Ball Dust Cover PRC ■ Accuracy ■ Selection of L-Balls ■ Lubrication
This is for the L-Ball LHS series. It is made of special
The accuracy of L-Balls is shown in Table 2. The static load capacity and maximum operating load LHSA is prepacked with lubricating grease ALVANIA
synthetic rubber which has excellent resistance to oil
of L-Balls are determined in consideration of the GREASE S2 (SHOWA SHELL SEKIYU K.K.). LHS is
and ozone. The cover offers very effective dust pro- Table 2 Tolerance strength of the ball stud and the body. Accordingly, not provided with prepacked grease. Perform proper
tection and prevents grease leakage.
L-Balls are selected on the basis of the static load lubrication.
LHSA LHS
capacity C s shown in the dimension table and the Operating LHS without lubrication will increase the

■ Identification Number maximum operating load shown in Table 3. wear of the sliding contact surface or cause seizure.

The identification number of L-Balls consists of a

Static load capacity

r1

r1
model code, a size and any supplemental codes as
shown in the examples.
V V
The static load capacity Cs shown in the dimension ■ Operating Temperature Range
table represents the allowable axial force F which is The maximum allowable temperature for L-Balls is
determined by the mechanical strength of the ball- +80℃ .
Examples of identification number unit: mm stud at the section 'A' under the bending moment due
to the force F as illustrated in Fig. 1. If F increases
Example 1 (Female thread of the dody Type Dimension symbol Tolerance
beyond the static load capacity, deformation will begin
: In case of right-hand threaded)
r1 ± 0.5
at A, leading to breakage. ■ Precautions for Use
Model code Size LHSA  0 1 Tightening depth
V
LHSA 8 − 0.2（1） 　 It is recommended that the tightening depth of the
r1 ± 0.4 screw into the body is more than twice the nominal
F
Type LHS diameter of thread.
V    h9
Size of thread Note(1)　This dimensional tolerance applies to LHSA 5 and higher.
2 Allowable tilting angle
（M8）
　 The allowable tilting angle is shown in Table 4.
A
Example 2 (Female thread of the body F′ Table 4 Allowable tilting angle
: In case of left threaded)

Supplemental Fig. 1
Model code Size code

LHSA 8 L
Maximum operating load
Left-handed thread
The strength of the body must also be taken into con- V

sideration when L-Balls are operated in a high-tem-

Example 3 (when a dust cover PRC is perature or low-temperature atmosphere or receive
attached to LHS)
repetitive loads of long duration or shock loads. A
guideline for maximum operating load of L-Balls is α α
Supplemental
Model code Size code shown in Table 3. When the fixing bolt in the main
body is fixed and a load is applied in the direction of unit: degree
LHS 8 D F′ , the bending stress in the fixing bolt must be taken
into consideration.
Nominal dia. mm
V
LHSA
α
LHS
α
K
With dust cover
  4 15 −
Table 3 Maximum operating load unit: N
  5 17 15
Identification Maximum Identification Maximum   6 17 17
number operating load number operating load   8 18 18
LHSA 4    840 LHS  5    880 10 19 19
LHSA 5 1 180 LHS  6 1 080 12 19 19
LHSA 6 1 080 LHS  8 1 630 14 20 20
LHSA 8 1 900 LHS10 2 100 16 − 20
LHSA10 2 170 LHS12 2 620 18 − 21
LHSA10M 2 170 LHS14 3 190 20 − 20
LHSA12 2 790 LHS16 3 820 22 − 21
LHSA14 3 540 LHS18 4 610
− − LHS20 5 340
− − LHS22 6 460
1N=0.102kgf=0.2248lbs.
K47 1mm=0.03937inch
K48
 L-BALL

L
D L1

D
2

W1
W1
S
1
L2 W2
V
LHSA 4 LHSA 8

D1
2

3
LHSA 5 LHSA 10
LHSA 6 LHSA 10M
P S 11 LHSA 12
LHSA 14

Mass Boundary dimensions　mm Static load

(Ref.) capacity
Identification number Thread
シールド形 Ball dia. Cs
g S V D L L1 L2 l1 W1 W2 D1 D2 r P r1 r球面外輪
2 r3
N
＊ ＊
LHSA    4 11 M  4×0.7 4 14 25 18 8 4 8 ─   8 10 19.5   5.5 ＊   7   7   5   8   880
LHSA    5 27 M  5×0.8 5 17 38.5 30 16 5 10 ─ 10 12 32.5   8 12 13 10 11.112 1 180
LHSA    6 27 M  6×1 6 19 39.5 30 16 5 10 ─ 10 12 32.5   8 12 13 10 11.112 1 670
LHSA    8 64 M  8×1.25 8 24 48 36 19 5 14 14 13 16 41.5 10 14.5 17 12.5 15 4 380
LHSA  10 106 M10×1.25 10 28 57 43 23 6.5 17 17 15 19 49 12 16 21 17 19.05 7 400
LHSA  10M 106 M10×1.5 10 28 57 43 23 6.5 17 17 15 19 49 12 16 21 17 19.05 7 400
LHSA  12 180 M12×1.75 12 34 67 50 27 6.5 19 19 17.5 22 64 14 20 30 20 22.225 9 900
LHSA  14 260 M14×2 14 38 76 57 30 8 22 22 20 25 72 17 22.5 33.5 22 25.4 14 600

Remarks1.   The item marked ＊ is manufactured with a neck diameter of φ3.4. The item marked ＊ is manufactured with a diameter of φ5.5
＊
instead of a width across flats.
2.   Provided with prepacked grease.

1N=0.102kgf=0.2248lbs.
K49 1mm=0.03937inch
K50
 L-BALL
L
D L1

W
S
r1
L2

r2

D1
r3

D2
P S l1

LHS

Mass Boundary dimensions　mm Static load

(Ref.) capacity
Identification number Thread Ball dia. Cs
g S V D B L L1 L2 l1 W D1 D2 r P r1 r2 r3
N

LHS    5 22 M  5×0.8 5 17   6   35.5 27 16   4   9   9 11 30.5   8 10 15 11 11.112   2 080
LHS    6 32 M  6×1 6 19.5   6.75   39.7 30 16   5 11 10 13 36.5 10 11.5 18.5 14 12.7 3 290
LHS    8 60 M  8×1.25 8 24   9   48 36 19   5 14 12.5 16 44 11 14.5 21.5 15 15.875 4 900
LHS  10 102 M10×1.5 10 28 10.5   57 43 23   6.5 17 15 19 52.5 13 17 26 18 19.05 7 640
LHS  12 160 M12×1.75 12 32 12   66 50 27   6.5 19 17.5 22 61 17 20 30 20 22.225 12 400
LHS  14 227 M14×2 14 36 13.5   75 57 30   8 22 20 25 69 17 22.5 33.5 22 25.4 14 600
LHS  16 300 M16×2 16 40 15   84 64 36   8 22 22 27 74 19 24.5 35.5 23 28.575 19 500
LHS  18 445 M18×1.5 18 45 16.5   93.5 71 40 10 27 25 31 84 22 27.5 40.5 25 31.75 25 600
LHS  20 580 M20×1.5 20 49 18 101.5 77 43 10 30 27.5 34 90.5 24 30 43 27 34.925 31 600
LHS  22 765 M22×1.5 22 54 20 111 84 47 12 32 30 37 99 27 32.5 47.5 30 38.1 39 800

Remark   No grease is prepacked. Perform proper lubrication.

1N=0.102kgf=0.2248lbs.
K51 1mm=0.03937inch
K52
 L-BALL
L-Ball Dust Cover
Y

X E F

H
Z

G
PRC

Boundary dimensions　mm

Identification number
X Y E F Z G H

PRC   5 20 29 10 19 16   8   8

PRC   6 22 31 11 20 19   9.5   9.5
PRC   8 27 38.5 13.5 25 24 12 12
PRC  10 31 45.5 15.5 30 27 14 13
PRC  12 36 53 18 35 32 16.5 15.5
PRC  14 40 60 20 40 36.5 19 17.5
PRC  16 44 68 22 46 40 20.5 19.5
PRC  18 49 74.5 24.5 50 46 23.5 22.5
PRC  20 54 82 27 55 50 25.5 24.5
PRC  22 59 89.5 29.5 60 53.5 27.5 26

1N=0.102kgf=0.2248lbs.
K53 1mm=0.03937inch
K54
 ■ Structure and Features Structures of Super Flexible Nozzles
Super Flexible Nozzle is a compact nozzle for
[Without nozzle]
use on a machine tool to supply and spray cutting oil Body
exactly at the required positions. (Zinc die-cast alloy)
The angle of the nozzle can be changed easily and
freely. Therefore, oil supply can be concentrated
upon the working area, and cooling and lubrication
can be performed effectively. As a result, cutting
resistance is reduced and superior finish is obtained,
Hollow ball
achieving high machining accuracy. Also, tool life is
longer.
The Super Flexible Nozzle is used in many places
such as at the spindle end of Machining Center and at [With nozzle]
the tool holder of N/C lathe. Body
(Zinc die-cast alloy)

The features of Super Flexible Nozzle are as follows.

1 A spherical bushing is incorporated to adjust the tilt-
ing angle of nozzle easily.
2 The Super Flexible Nozzle is compact in size, and
the design on parts around the spindle and tool can
be made simple. Hollow ball Nozzle

3 The nozzle length is short, and winding of cutting

chips around the nozzle will not occur.
4 By using a number of Super Flexible Nozzles, cut-
Body
ting oil can be supplied and cutting chips can be (Steel)
Metric thread
removed more effectively.
5 The press fitting type and screw fitting type are
available. The press fitting type is economical.

Nozzle

O-ring Hollow ball

Body
(Steel)
Taper pipe thread

K
Nozzle

O-ring Hollow ball

K55 K56
■ Types ■ Precautions for Use SUPER FLEXIBLE NOZZLE
Super Flexible Nozzles shown in Table 1 are avail- When the press fitting type Super Flexible Nozzle is Press Fitting Type Without Nozzle L1
able. used, a φ 15 (H8) ＋ 0.027
　0 bore for fitting hole must be C L2
prepared and fitting is made from the 30°chamfered r

end of the outer body. In this case, the body portion

Table 1 Type of Super Flexible Nozzle
should be pushed for press fitting.
When the screw fitting type Super Flexible Nozzle is

α
Type Model code
used and prevention of oil leakage from the fitting part

d
Press fitting Without nozzle is required, it is recommended to wind sealing tape on

α
type SNA
With nozzle the thread portion or use rubber packing for the shoul-

30°
With metric threads SNM der face of the outer body.
Screw fitting
type With taper pipe threads The direction of lubrication can be adjusted by insert-
SNPT
ing a screwdriver, etc. in the bore of the nozzle. SNA

■ Identification Number ■ Special Specifications Boundary dimensions　mm Ball Allowable

The identification number of Super Flexible Nozzle Super Flexible Nozzles with special length are also dia. tilting angle
Identification
consists of a model code and a size. An example is available. In this case, specify the necessary nozzle number
shown as follows. length in units of 1 mm, but do not exceed the maxi- d D L1 L2 C r
mm α
(inch) degree
mum length shown in the dimension table as "L".
Super Flexible Nozzles with curved nozzle end or with SNA 4 4 11.112 36
15 7 1 6 2
special bore diameter are also available. In this case, （ 7╱16）
Example of identification number SNA 6 6 24
please contact by preparing a drawing or sketch
with necessary specifications.
Model code Size

SNM 10 - 20
Type of nozzle
Press Fitting Type With Nozzle L1 L
C L2
r
Nozzle bore or
thread size:（M10×1.25）

Dimension from shoulder surface to nozzle top:※

（20mm）

(d1)
D

d
α
※In case of press fitting type without nozzle, this

30°
dimension is not indicated.

SNA

K
Boundary dimensions　mm Ball Allowable
dia. tilting angle
Identification
number
d D L L1 L2 C r d1
mm α
(inch) degree

SNA 3-L 3 6 15 32 11.112
15 7 1 6 2 6 24
（ 7╱16）
SNA 4-L 4 6 16 40

1N=0.102kgf=0.2248lbs.
K57 1mm=0.03937inch
K58
 SUPER FLEXIBLE NOZZLE
Screw Fitting Type L1 L
L2
L3

●Seals for Needle Roller Bearings

α
(d1)
●Cir-clips for Needle Roller Bearings

d2
B

d
●Needle Rollers

α
S S

SNM SNPT

Boundary dimensions　mm Ball Allowable

dia. tilting angle
Identification Width across Width across
Thread flats corners
number
d S L L1 L2 L3 d1 d2 B (Ref.)
mm α
(inch) degree

SNM   10-L M10×1.25 12.700

4 20 40 60   9 13 10.5   6   6 17 19.6
SNPT 1/4-L PT 1/4 （   1╱2）

SNM   20-L M20×1.5 19.050

6 30 50 70 13 18 15   8 10 24 27.7 35
SNPT 3/8-L PT 3/8 （   3╱4）

SNM   24-L M24×2.0 25.400

8 40 60 80 18 23 19 10 12 32 37
SNPT 1/2-L PT 1/2 （1 ）

1N=0.102kgf=0.2248lbs.
K59 1mm=0.03937inch
 ■ Precautions for Use
 1 For the single lip OS type, the lip has to face inward
when using the seal to prevent grease leakage, and
outward to prevent the penetration of foreign particles.
The DS type of double-lips is effective for prevention
of grease leakage and dust penetration. However,
when the main purpose is to prevent grease leakage,

■ Features ■ Identification Number

the main lip should face inward, and when used main-
ly to prevent dust penetration, it should face outward.
Seals for Needle Roller Bearings have a low The identification number of Seals for Needle Roller  2 The permissible temperature range is -20 〜
sectional height and consist of a sheet metal ring and Bearings consists of a model code and dimensions. +100℃ .
special synthetic rubber. An example of an identification number is shown as For use at higher or lower temperatures, a special
As these seals are manufactured to the same section- follows. seal is required. Please contact for further infor-
al height as Needle Roller Bearings, grease mation.
leakage and the penetration of foreign particles can  3 The limiting peripheral speed of shaft depends on
the conditions of use, but is normally 6 to 8 m/s.
be effectively prevented by fitting them directly to the Example of identification number
sides of combinable bearings shown in the dimension Double this speed is possible if the conditions (lubri-
table. cation, temperature, shaft finish, etc.) are good.
When fitting seals to needle roller bearings with inner Model code Dimensions

■ Mounting
ring, wide inner rings (see page H2) must be used, as DS 20 28 4
shown in the mounting examples.
Type of seal When inserting the shaft, damage to the lip should be

■ Types Shaft dia.

prevented by chamfering the end of the shaft, as
shown in the upper part of Fig. 1. When this cannot
Seals for Needle Roller Bearings are available as （20mm） be performed, a mounting bushing should be used, as
shown in Table1. shown in the lower part of Fig.1.
Outside dia. of seal
（28mm） When press fitting the seal to the housing, do not
strike it directly, but fit it gently, using a suitable tool.
Table 1 Seal type Width of seal To prevent early wear and heat generation at the seal
（4mm）
surface, it is necessary to thickly coat the tip of the lip
Type Single lip Double lips
for the OS type, or to fill the space between the two
lips for the DS type, with bearing grease.
Metal ring Metal ring

■ Accuracy
Secondary lip
Structure Lip Main lip Tolerances of Seals for Needle Roller Bearings are
3mm
based on JIS B 2402-1. Fig.2 Mounting examples

30°
Tolerances of outside diameter and width are based
on Tables 2 and 3, respectively.

Model code OS DS Table 2 Tolerance of outside diameter unit: mm

Nominal outside diameter Tolerance
Over Incl. High Low Bushing for mounting

− 30 ＋ 0.09 ＋ 0.04 Secondary lip Main lip L

30 50 ＋ 0.11 ＋ 0.05
50 80 ＋ 0.14 ＋ 0.06
Fig.1
80 120 ＋ 0.17 ＋ 0.08

Table 3 Tolerance of width unit: mm

Nominal size of width Tolerance
Over Incl. High Low
− 6 ＋ 0.2 − 0.2
6 10 ＋ 0.3 − 0.3
1N=0.102kgf=0.2248lbs.
L1 1mm=0.03937inch
L2
SEALS FOR NEEDLE ROLLER BEARINGS

b b

d1 (Shaft dia.)

d1 (Shaft dia.)
D

D
OS DS
Shaft dia. 6 − 15mm

Identification number Boundary Combinable bearings Identification number Boundary Combinable bearings
Shaft dimensions　mm Shaft dimensions　mm
dia. dia.
TA … Z  YT RNA  TR RNAF NAX TA … Z  YT RNA  TR RNAF NAX
mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX
6 OS   6102.5 ─   6 10 2.5 TLA     69Z ─ ─ ─ OS 12163 ─ 12 16 3 TLA 1210Z ─ ─ ─
YTL 1210
7 OS   7112.5 ─   7 11 2.5 TLA     79Z ─ ─ ─
OS 12183 ─ 12 18 3 TLA 1212Z ─ ─ ─
OS   8123 ─   8 12 3 TLA   810Z ─ ─ ─
─ 12 OS 12193 ─ 12 19 3 TA 1212Z TAF 121912 ─ ─
OS   8153   8 15 3 TA   810Z RNA      496 RNAF   81510 ─
8 TA 1215Z TAF 121916
TA   815Z TAF   81512
TA 1220Z
TA   820Z TAF   81516
─ YT   810
TA 1225Z
YT 1212
OS   9133 ─   9 13 3 TLA   910Z ─ ─ ─
13 OS 13193 ─ 13 19 3 TLA 1312Z ─ ─ ─
TLA   912Z
─ ─ OS 14203 DS 14203 14 20 3 TLA 1412Z ─ ─ ─
9 OS   9163   9 16 3 TA   912Z TAF   91612 ─
TAF   91616 TLA 1416Z
TA   916Z
YT   912 14 OS 14223 DS 14223 14 22 3 TA 1416Z RNA 4900 RNAF 142213 ─
TA 1420Z TAF 142216 RNAFW 142220
OS 10143 ─ 10 14 3 TLA 1010Z ─ ─ ─
TAF 142220
TLA 1012Z
TLA 1015Z OS 15213 DS 15213 15 21 3 TLA 1512Z ─ ─ ─
TLA 1516Z
10 OS 10173 ─ 10 17 3 TA 1010Z TAF 101712 RNAF 101710 ─
TLA 1522Z
TA 1012Z TAF 101716
TA 1015Z OS 15223 DS 15223 15 22 3 TA 1510Z ─ ─ ─
TA 1020Z TA 1512Z
15
TA 1515Z
TA 1520Z
TA 1525Z L
OS 15235 DS 15235 15 23 5 ─ TAF 152316 RNAF 152313 ─
TAF 152320 RNAFW 152320

1N=0.102kgf=0.2248lbs.
L3 1mm=0.03937inch
L4
SEALS FOR NEEDLE ROLLER BEARINGS

b b

d1 (Shaft dia.)

d1 (Shaft dia.)
D

D
OS DS
Shaft dia. 16 − 19mm

Identification number Boundary Combinable bearings Identification number Boundary Combinable bearings
Shaft dimensions　mm Shaft dimensions　mm
dia. dia.
TA … Z  YT RNA  TR RNAF NAX TA … Z  YT RNA  TR RNAF NAX
mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX
OS 16223 DS 16223 16 22 3 TLA 1612Z ─ ─ ─ OS 18243 DS 18243 18 24 3 TLA 1812Z ─ ─ ─
TLA 1616Z TLA 1816Z
TLA 1622Z
OS 18253 DS 18253 18 25 3 TA 1813Z ─ ─ ─
OS 16243 DS 16243 16 24 3 TA 1616Z RNA    4901 RNAF 162413 ─ TA 1815Z
16 RNA    6901
TA 1620Z RNAFW 162420 TA 1817Z
TAF 162416 18 TA 1819Z
TAF 162420 TA 1820Z
TA 1825Z
OS 16285 DS 16285 16 28 5 ─ ─ RNAF 162812 ─
OS 18264 DS 18264 18 26 4 ─ RNA   49/14 RNAF 182613 ─
OS 17233 DS 17233 17 23 3 TLA 1712Z ─ ─ ─
TAF 182616 RNAFW 182620
OS 17243 DS 17243 17 24 3 TA 1715Z ─ ─ ─ TAF 182620
TA 1720Z
OS 19274 ─ 19 27 4 TA 1916Z TAF 192716 ─ ─
TA 1725Z 19
17 TA 1920Z TAF 192720
YT 1715
YT 1725
OS 17253 DS 17253 17 25 3 ─ TAF 172516 RNAF 172513 ─
TAF 172520 RNAFW 172520

1N=0.102kgf=0.2248lbs.
L5 1mm=0.03937inch
L6
SEALS FOR NEEDLE ROLLER BEARINGS

b b

d1 (Shaft dia.)

d1 (Shaft dia.)
D

D
OS DS
Shaft dia. 20 − 24mm

Identification number Boundary Combinable bearings Identification number Boundary Combinable bearings
Shaft dimensions　mm Shaft dimensions　mm
dia. dia.
TA … Z  YT RNA  TR RNAF NAX TA … Z  YT RNA  TR RNAF NAX
mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX
OS 20264 DS 20264 20 26 4 TLA 2012Z ─ ─ ─ OS 22284 DS 22284 22 28 4 TLA 2212Z ─ ─ ─
TLA 2016Z TLA 2216Z
TLA 2020Z TLA 2220Z
TLA 2030Z
OS 22294 ─ 22 29 4 TA 2210Z ─ ─ ─
OS 20274 DS 20274 20 27 4 TA 2015Z ─ ─ ─ TA 2215Z
TA 2020Z TA 2220Z
22
TA 2025Z TA 2225Z
TA 2030Z TA 2230Z
YT 2015
OS 22304 DS 22304 22 30 4 TA 223016Z RNA    4903 RNAF 223013 ─
YT 2025
TA 223020Z RNA    6903 RNAFW 223026
20 OS 20284 DS 20284 20 28 4 TA 202820Z RNA    4902 RNAF 202813 ─ YT 223016 TAF 223016
YT 202820 RNA    6902 RNAFW 202826 YT 223020 TAF 223020
TAF 202816
OS 24314 DS 24314 24 31 4 TA 2420Z ─ ─ ─
TAF 202820
TA 2428Z
OS 20304 DS 20304 20 30 4 ─ ─ ─ NAX 2030 YT 2428
NBX 2030 24 OS 24324 DS 24324 24 32 4 TA 243216Z TAF 243216 ─ ─
OS 20324 DS 20324 20 32 4 ─ ─ RNAF 203212 ─ TA 243220Z TAF 243220
RNAFW 203224 YT 243216
YT 243220
OS 20326 DS 20326 20 32 6 ─ ─ RNAF 203212 ─
RNAFW 203224
OS 21294 DS 21294 21 29 4 TA 2116Z TAF 212916 ─ ─
21
TA 2120Z
YT 2116
TAF 212920
L
YT 2120

1N=0.102kgf=0.2248lbs.
L7 1mm=0.03937inch
L8
SEALS FOR NEEDLE ROLLER BEARINGS

b b

d1 (Shaft dia.)

d1 (Shaft dia.)
D

D
OS DS
Shaft dia. 25 − 29mm

Identification number Boundary Combinable bearings Identification number Boundary Combinable bearings
Shaft dimensions　mm Shaft dimensions　mm
dia. dia.
TA … Z  YT RNA  TR RNAF NAX TA … Z  YT RNA  TR RNAF NAX
mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX
OS 25324 DS 25324 25 32 4 TLA 2512Z ─ ─ ─ OS 28354 DS 28354 28 35 4 TLA 2816Z ─ ─ ─
TLA 2516Z TLA 2820Z
TLA 2520Z
OS 28374 DS 28374 28 37 4 TA 2820Z TAF 283720 ─ ─
TLA 2526Z
TA 2830Z TAF 283730
TLAW 2538Z
28 YT 2820
YTL 2526
OS 28396 DS 28396 28 39 6 ─ RNA   49/22 ─ ─
OS 25334 DS 25334 25 33 4 TA 2510Z TAF 253316 ─ ─
RNA   69/22
TA 2515Z TAF 253320
TA 2520Z OS 28406 DS 28406 28 40 6 ─ ─ RNAF 284016 ─
TA 2525Z RNAFW 284032
25 TA 2530Z OS 29384 DS 29384 29 38 4 TA 2920Z TAF 293820 ─ ─
YT 2510 29 TA 2930Z TAF 293830
YT 2515 YT 2920
YT 2520
YT 2525
OS 25356 DS 25356 25 35 6 ─ ─ RNAF 253517 ─
RNAFW 253526
OS 25376 DS 25376 25 37 6 ─ RNA    4904 RNAF 253716 NAX 2530
RNA    6904 RNAFW 253732 NBX 2530

OS 26344 DS 26344 26 34 4 TA 2616Z TAF 263416 ─ ─

26
TA 2620Z
YT 2616
TAF 263420
L
YT 2620

1N=0.102kgf=0.2248lbs.
L9 1mm=0.03937inch
L10
SEALS FOR NEEDLE ROLLER BEARINGS

b b

d1 (Shaft dia.)

d1 (Shaft dia.)
D

D
OS DS
Shaft dia. 30 − 38mm

Identification number Boundary Combinable bearings Identification number Boundary Combinable bearings
Shaft dimensions　mm Shaft dimensions　mm
dia. dia.
TA … Z  YT RNA  TR RNAF NAX TA … Z  YT RNA  TR RNAF NAX
mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX
OS 30374 DS 30374 30 37 4 TLA 3012Z ─ ─ ─ OS 35424 DS 35424 35 42 4 TLA 3512Z ─ ─ ─
TLA 3016Z TLA 3516Z
TLA 3018Z TLA 3520Z
TLA 3020Z
OS 35454 DS 35454 35 45 4 TA 3512Z TAF  354520 RNAF 354517 ─
TLA 3026Z
TA 3515Z TAF  354530 RNAFW 354526
TLAW 3038Z
TA 3520Z
RNAF 304017 ─ 35
OS 30404 DS 30404 30 40 4 TA 3013Z TAF  304020 TA 3525Z
30 TA 3015Z TAF  304030 RNAFW 304026 TA 3530Z
TA 3020Z
OS 35476 DS 35476 35 47 6 ─ RNA     4906 RNAF 354716 NAX 3530
TA 3025Z
RNA     6906 RNAFW 354732 NBX 3530
TA 3030Z
OS 30426 DS 30426 30 42 6 ─ RNA     4905 RNAF 304216 NAX 3030
RNA     6905 RNAFW 304232 NBX 3030
OS 37474 DS 37474 37 47 4 TA 3720Z TAF  374720 ─ ─
37 TA 3730Z TAF  374730
YT 3720
OS 32424 DS 32424 32 42 4 TA 3220Z TAF  324220 ─ ─
OS 38484 DS 38484 38 48 4 TA 3815Z TAF  384820 ─ ─
TA 3230Z TAF  324230
TA 3820Z TAF  384830
YT 3220
32 TA 3825Z
OS 32456 DS 32456 32 45 6 ─ RNA    49/28 ─ ─ 38 TA 3830Z
RNA    69/28 TAW 3845Z
GTR 324530
OS 38506 DS 38506 38 50 6 ─ ─ ─ ─

1N=0.102kgf=0.2248lbs.
L11 1mm=0.03937inch
L12
SEALS FOR NEEDLE ROLLER BEARINGS

b b

d1 (Shaft dia.)

d1 (Shaft dia.)
D

D
OS DS
Shaft dia. 40 − 50mm

Identification number Boundary Combinable bearings Identification number Boundary Combinable bearings
Shaft dimensions　mm Shaft dimensions　mm
dia. dia.
TA … Z  YT RNA  TR RNAF NAX TA … Z  YT RNA  TR RNAF NAX
mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX
OS 40474 DS 40474 40 47 4 TLA 4012Z ─ ─ ─ OS 45524 DS 45524 45 52 4 TLA 4516Z ─ ─ ─
TLA 4016Z TLA 4520Z
TLA 4020Z
OS 45554 DS 45554 45 55 4 TA 4520Z TAF  455520 RNAF 455517 ─
OS 40504 DS 40504 40 50 4 TA 4015Z TAF  405020 RNAF 405017 ─ TA 4525Z TAF  455530 RNAFW 455534
TA 4020Z TAF  405030 RNAFW 405034 TA 4530Z
45
TA 4025Z TA 4540Z
TA 4030Z YT 4520
TA 4040Z YT 4525
40 YT 4015
OS 45627 DS 45627 45 62 7 ─ ─ RNAF 456220 ─
YT 4025
RNAFW 456240
OS 40526 DS 40526 40 52 6 ─ RNA    49/32 ─ NAX 4032
─ ─
OS 48627 DS 48627 48 62 7 RNA     4908 ─
RNA    69/32 NBX 4032
RNA     6908
48
TR    486230
GTR 486230
OS 40556 DS 40556 40 55 6 ─ TR    405520 RNAF 405520 ─ ─
OS 50584 DS 50584 50 58 4 TLA 5020Z ─ ─
GTR 405520 RNAFW 405540
TLA 5025Z
OS 42557 DS 42557 42 55 7 ─ RNA     4907 ─ ─
42 OS 50624 DS 50624 50 62 4 TA 5012Z TAF  506225 RNAF 506220 NAX 5035
RNA     6907
TA 5015Z TAF  506235 RNAFW 506240 NBX 5035
TA 5020Z
50 TA 5025Z
TA 5030Z
TA 5040Z
TAW 5045Z L
OS 50657 DS 50657 50 65 7 ─ RNA     49/42 RNAF 506520 ─
RNAFW 506540

1N=0.102kgf=0.2248lbs.
L13 1mm=0.03937inch
L14
SEALS FOR NEEDLE ROLLER BEARINGS

b b

d1 (Shaft dia.)

d1 (Shaft dia.)
D

D
OS DS
Shaft dia. 52 − 72mm

Identification number Boundary Combinable bearings Identification number Boundary Combinable bearings
Shaft dimensions　mm Shaft dimensions　mm
dia. dia.
TA … Z  YT RNA  TR RNAF NAX TA … Z  YT RNA  TR RNAF NAX
mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX mm Single lip Double lips d1 D b TLA … Z  YTL TAF   GTR NBX
OS 52687 DS 52687 52 68 7 ─ RNA    4909 ─ ─ OS 65774 DS 65774 65 77 4 TA 6525Z ─ ─ ─
52
RNA    6909 TA 6530Z
TAW 6545Z
OS 55674 DS 55674 55 67 4 TA 5520Z ─ ─ ─ 65 TAW 6550Z
TA 5525Z
TA 5530Z OS 65857 DS 65857 65 85 7 ─ ─ RNAF 658530 ─
TA 5540Z RNAFW 658560
TAW 5545Z
OS 68857 DS 68857 68 85 7 ─ RNA    4912 ─ ─
55 TAW 5550Z 68
RNA    6912
OS 55687 DS 55687 55 68 7 ─ TAF  556825 RNAF 556820 ─
─ ─ ─
OS 70824 DS 70824 70 82 4 TA 7025Z
TAF  556835 RNAFW 556840
TA 7030Z
OS 55727 ─ 55 72 7 ─ ─ RNAF 557220 ─ TA 7040Z
RNAFW 557240 TAW 7050Z
YT 7025
OS 58727 DS 58727 58 72 7 ─ RNA     4910 ─ ─ 70
58 YT 7030
RNA     6910
YT 7040
OS 60724 DS 60724 60 72 4 TA 6025Z TAF  607225 ─ NAX 6040
OS 70907 DS 70907 70 90 7 ─ ─ RNAF 709030 ─
TA 6030Z TAF  607235 NBX 6040
RNAFW 709060
TA 6040Z
60 TAW 6045Z OS 72907 DS 72907 72 90 7 ─ RNA    4913 ─
72
TAW 6050Z RNA    6913
OS 60787 DS 60787 60 78 7 ─ ─ RNAF 607820 ─
RNAFW 607840
62 OS 62744 DS 62744 62 74 4 TA 6212Z ─ ─ ─ L
OS 63807 DS 63807 63 80 7 ─ RNA     4911 ─ ─
63
RNA     6911

1N=0.102kgf=0.2248lbs.
L15 1mm=0.03937inch
L16
 ■ Allowable Rotational Speed ■ Mounting
Cir-clips for Needle Roller Bearings are fixed in the The mounting dimensions for Cir-clips for Needle
groove with a certain amount of pressure on the bot- Roller Bearings are shown in the dimension table.
tom of the groove. In the case of Cir-clips for shaft When using these Cir-clips to restrict the movement
WR type, the centrifugal force causes a decrease in of the needle roller cage in the axial direction, it is rec-
the gripping pressure. Therefore, when using them at ommended that a spacer be used between the Cir-
high rotational speeds, it is necessary to first check clip and the cage. Spacers are not required at low

■ Features ■ Identification number

the allowable rotational speed shown in Fig.1. rotational speeds.
When it is difficult to reach Cir-clips with dismounting
The identification number of Cir-clips consists of a tools and disassembly is difficult, or when the fre-
Cir-clips for Needle Roller Bearings have been
specially designed for needle roller bearings on model code and a size as shown below. quency of dismounting is high, it is necessary to con-
which, in many cases, generally available Cir-clips sider the use of a retaining ring (JIS B 2804), although
cannot be used. They have a low sectional height they have a higher sectional height.
70000
60000
and are very rigid. They are made of spring steel.
Examples of identification number 50000
There are Cir-clips for shafts and for bores, and they 40000
are used for positioning to prevent bearing movement Example 1 30000
in the axial direction. Model code Size
20000
WR 20
■ Types Type of
Cir-clip
10000
8000
Cir-clips for Needle Roller Bearings are available as 7000
6000
shown in Table. 1. Shaft dia. 5000
（20mm）

Allowable rotational speed min-1

4000

Table 1 Type of Cir-clip 3000

Type For shaft For bore

Example 2 2000
Model code Size

AR 35 1000
800
Type of 700
Cir-clip 600
500
Shape Bore dia.
400

（35mm） 300

200

Model code WR AR 100

20 40 60 80 100 120 140 160 180

Shaft dia. mm

Fig.1 Allowable rotational speed

1N=0.102kgf=0.2248lbs.
L17 1mm=0.03937inch
L18
 CIR-CLIPS FOR NEEDLE ROLLER BEARINGS
For Shaft

e
60° m

D1
D
f m = f + 0.1mm(min.)
D3

WR

Shaft dia. 4 − 390mm

Boundary dimensions　mm Boundary dimensions　mm Boundary dimensions　mm

Identification Shaft dia. Groove dia. Identification Shaft dia. Groove dia. Identification Shaft dia. Groove dia.
number number number
D D3 e f D1 Tolerance D D3 e f D1 Tolerance D D3 e f D1 Tolerance
(Max.) (Max.) (Max.)

WR   4   4   3.7 0.8 0.5   3.8 WR   42 42 39.8 2.3 1.5 40.5 WR 170 170 166.6 4 2.5 167.4 　0
WR   5   5   4.7 1 0.5   4.8 WR   43 43 40.8 2.3 1.5 41.5 WR 175 175 171.6 4 2.5 172.4 −0.25
43.5 　0
WR   6   6   5.6 1.1 0.7   5.7 WR   45 45 42.8 2.3 1.5 WR 180 180 175.6 5 3 177
　0 45.5 −0.16
WR   7   7   6.5 1.2 0.7   6.7 WR   47 47 44.8 2.3 1.5 WR 185 185 180.6 5 3 182
−0.09 1.5 48.5 187
WR   8   8   7.4 1.3 1   7.6 WR   50 50 47.8 2.3 WR 190 190 185.6 5 3
WR   9   9   8.4 1.3 1   8.6 WR   52 52 49.8 2.3 1.5 50.5 WR 195 195 190.6 5 3 192
WR 10 10   9.4 1.3 1   9.6 WR   55 55 52.6 2.3 1.5 53.5 WR 200 200 195.6 5 3 197 　0
WR 11 11 10.2 1.3 1 10.5 WR   60 60 57.6 2.3 1.5 58.5 WR 210 210 205.6 5 3 207 −0.29
WR 12 12 11.2 1.3 1 11.5 WR   63 63 60.6 2.3 1.5 61.5 WR 220 220 215.6 5 3 217
　0
WR 13 13 12.1 1.3 1 12.5 WR   65 65 62.6 2.3 1.5 63.5 WR 230 230 225.6 5 3 227
−0.19
WR 14 14 13.1 1.5 1.2 13.5 　0 WR   68 68 65.4 2.8 2 66.2 WR 240 240 235.6 5 3 237
WR 15 15 14 1.75 1.2 14.4 −0.11 WR   70 70 67.4 2.8 2 68.2 WR 260 260 253 7.5 4 255
WR 16 16 15 1.75 1.2 15.4 WR   75 75 72.4 2.8 2 73.2 WR 265 265 258 7.5 4 260
WR 17 17 16 1.75 1.2 16.4 WR   80 80 77.4 2.8 2 78.2 WR 270 270 263 7.5 4 265
WR 18 18 17 1.75 1.2 17.4 WR   82 82 79.3 3.4 2.5 80.2 WR 280 280 273 7.5 4 275 　0
WR 19 19 17.9 1.75 1.2 18.4 WR   85 85 82 3.4 2.5 83 WR 285 285 278 7.5 4 280 −0.32
WR 20 20 18.7 1.75 1.2 19.2 WR   90 90 87 3.4 2.5 88 WR 300 300 293 7.5 4 295
WR 21 21 19.7 1.75 1.2 20.2 WR   95 95 92 3.4 2.5 93 WR 305 305 298 7.5 4 300
　0
WR 22 22 20.7 1.75 1.2 21.2 WR 100 100 97 3.4 2.5 98 WR 320 320 313 7.5 4 315
−0.22
WR 23 23 21.7 1.75 1.2 22.2 WR 105 105 101.7 3.4 2.5 102.7 WR 330 330 323 7.5 4 325
1.2 　0 3.4 2.5 4 335
WR 24 24 22.5 1.75 23 WR 110 110 106.7 107.7 WR 340 340 333 7.5
1.2 −0.13 3.4 2.5 4 345 　0
WR 25 25 23.5 1.75 24 WR 115 115 111.7 112.7 WR 350 350 343 7.5
WR 26 26 24.5 1.75 1.2 25 WR 120 120 116.7 3.4 2.5 117.7 WR 360 360 353 7.5 4 355 −0.36
WR 28 28 26.5 2.3 1.5 27 WR 125 125 121.7 3.4 2.5 122.7 WR 370 370 363 7.5 4 365
WR 29 29 27.5 2.3 1.5 28 WR 130 130 126.7 3.4 2.5 127.7 WR 390 390 383 7.5 4 385
WR 30 30 28.5 2.3 1.5 29 WR 135 135 131.6 4 2.5 132.4
WR 32
WR 35
32
35
30.2
33.2
2.3
2.3
1.5
1.5
30.8
33.8
WR 140
WR 145
140
145
136.6
141.6
4
4
2.5
2.5
137.4
142.4
　0
−0.25
L
WR 36 36 34.2 2.3 1.5 34.8 　0 WR 150 150 146.6 4 2.5 147.4
WR 37 37 35.2 2.3 1.5 35.8 −0.16 WR 155 155 151.6 4 2.5 152.4
WR 38 38 36.2 2.3 1.5 36.8 WR 160 160 156.6 4 2.5 157.4
WR 40 40 37.8 2.3 1.5 38.5 WR 165 165 161.6 4 2.5 162.4

1N=0.102kgf=0.2248lbs.
L19 1mm=0.03937inch
L20
 CIR-CLIPS FOR NEEDLE ROLLER BEARINGS
For Bore
m
90°

D1
D
f D3
m = f + 0.1mm(min.)

AR

Bore dia. 7 − 440mm

Boundary dimensions　mm Boundary dimensions　mm Boundary dimensions　mm Boundary dimensions　mm

Identification Bore dia. Groove dia. Identification Bore dia. Groove dia. Identification Bore dia. Groove dia. Identification Bore dia. Groove dia.
number number number number
D D3 e f D1 Tolerance D D3 e f D1 Tolerance D D3 e f D1 Tolerance D D3 e f D1 Tolerance
(Min.) (Min.) (Min.) (Min.)

AR   7 7   7.5 1 0.8   7.3 AR 40 40 41.8 2.3 1.5 41.2 AR   93 93   96 3.4 2.5   95 AR 170 170 173.6 4 2.5 172.6
＋0.09
AR   8 8   8.5 1 0.8   8.3
　0
AR 42 42 43.8 2.3 1.5 43.2 AR   95 95   98 3.4 2.5   97 AR 173 173 176.6 4 2.5 175.6 ＋0.25
AR   9 9   9.5 1.1 0.8   9.3 AR 43 43 44.8 2.3 1.5 44.2
＋0.16
AR   97 97 100 3.4 2.5   99 AR 175 175 178.6 4 2.5 177.6 　0
AR 10 10 10.6 1.2 0.8 10.4 AR 44 44 45.8 2.3 1.5 45.2 AR   98 98 101 3.4 2.5 100 AR 180 180 183.6 4 2.5 182.6
46.2 　0 185.6
AR 11 11 11.6 1.3 1 11.4 AR 45 45 46.8 2.3 1.5 AR 100 100 103 3.4 2.5 102 AR 183 183 186.6 4 2.5
AR 12 12 12.7 1.3 1 12.4 AR 47 47 48.8 2.3 1.5 48.2 AR 102 102 105.3 3.4 2.5 104.3 AR 190 190 194.5 5 3 193
AR 13 13 13.8 1.3 1 13.5 ＋0.11 AR 48 48 49.8 2.3 1.5 49.2 AR 103 103 106.3 3.4 2.5 105.3 ＋0.22 AR 195 195 199.5 5 3 198
AR 14 14 14.8 1.3 1 14.5 　0 AR 50 50 51.8 2.3 1.5 51.2 AR 105 105 108.3 3.4 2.5 107.3 　0 AR 200 200 204.5 5 3 203
AR 15 15 15.8 1.3 1 15.5 AR 52 52 54.3 2.3 1.5 53.5 AR 107 107 110.3 3.4 2.5 109.3 AR 205 205 209.5 5 3 208
1.2 2.3 1.5 2.5 3 213 ＋0.29
AR 16 16 16.8 1.6 16.5 AR 53 53 55.3 54.5 AR 108 108 111.3 3.4 110.3 AR 210 210 214.5 5
1.2 2.3 1.5 2.5 5 3 218 　0
AR 17 17 17.8 1.6 17.5 AR 55 55 57.3 56.5 AR 110 110 113.3 3.4 112.3 AR 215 215 219.5
AR 18 18 18.9 1.75 1.2 18.5 AR 57 57 59.3 2.3 1.5 58.5 AR 112 112 115.3 3.4 2.5 114.3 AR 220 220 224.5 5 3 223
AR 19 19 19.9 1.75 1.2 19.6 AR 58 58 60.3 2.3 1.5 59.5 AR 113 113 116.3 3.4 2.5 115.3 AR 225 225 229.5 5 3 228
AR 20 20 21 1.75 1.2 20.6 AR 60 60 62.3 2.3 1.5 61.5 AR 115 115 118.3 3.4 2.5 117.3 AR 230 230 234.5 5 3 233
AR 21 21 22 1.75 1.2 21.6 AR 62 62 64.3 2.3 1.5 63.5 ＋0.19 AR 117 117 120.3 3.4 2.5 119.3 AR 235 235 239.5 5 3 238
AR 22 22 23 1.75 1.2 22.6 AR 65 65 67.3 2.3 1.5 66.5 　0 AR 118 118 121.3 3.4 2.5 120.3 AR 240 240 244.5 5 3 243
AR 23 23 24 1.75 1.2 23.6 ＋0.13 AR 68 68 70.3 2.3 1.5 69.5 AR 120 120 123.3 3.4 2.5 122.3 AR 245 245 249.5 5 3 248
AR 24 24 25.2 1.75 1.2 24.8 　0 AR 70 70 72.3 2.3 1.5 71.5 AR 123 123 126.3 3.4 2.5 125.3 AR 250 250 254.5 5 3 253
1.2 2.8 2 2.5 7.5 4 ＋0.32
AR 25 25 26.2 1.75 25.8 AR 72 72 74.6 73.8 AR 125 125 128.3 3.4 127.3 AR 260 260 267 265
1.2 2.8 2 2.5 7.5 4 　0
AR 26 26 27.2 1.75 26.8 AR 73 73 75.6 74.8 AR 127 127 130.3 3.4 129.3 AR 270 270 277 275
AR 27 27 28.2 1.75 1.2 27.8 AR 75 75 77.6 2.8 2 76.8 AR 130 130 133.3 3.4 2.5 132.3 AR 280 280 287 7.5 4 285
AR 28 28 29.2 1.75 1.2 28.8 AR 76 76 78.6 2.8 2 77.8 AR 133 133 136.3 3.4 2.5 135.3 AR 300 300 307 7.5 4 305
AR 29 29 30.2 1.75 1.2 29.8 AR 78 78 80.6 2.8 2 79.8 AR 135 135 138.3 3.4 2.5 137.3 AR 320 320 327 7.5 4 325
1.5 2.8 2 2.5 ＋0.25 7.5 4
AR 30 30 31.4 2.3 31 AR 80 80 82.6 81.8 AR 137 137 140.3 3.4 139.3 AR 325 325 332 330
1.5 2.8 2 2.5 　0 7.5 4 ＋0.36
AR 31 31 32.4 2.3 32 AR 81 81 83.6 82.8 AR 140 140 143.6 4 142.6 AR 355 355 362 360
1.5 2.8 2 2.5 7.5 4 　0
AR 32 32 33.4 2.3 33 AR 82 82 84.6 83.8 AR 143 143 146.6 4 145.6 AR 375 375 382 380
AR 33
AR 34
33
34
34.4
35.4
2.3
2.3
1.5
1.5
34
35 ＋0.16
　0
AR 83
AR 85
83
85
85.6
87.6
2.8
2.8
2
2
84.8
86.8
＋0.22
　0
AR 145
AR 150
145
150
148.6
153.6
4
4
2.5
2.5
147.6
152.6
AR 395
AR 415
395
415
402
422
7.5
7.5
4
4
400
420
＋0.4
L
AR 35 35 36.4 2.3 1.5 36 AR 86 86 88.6 2.8 2 87.8 AR 153 153 156.6 4 2.5 155.6 AR 420 420 427 7.5 4 425
1.5 3.4 2.5 2.5 7.5 4 　0
AR 37 37 38.8 2.3 38.2 AR 88 88 91 90 AR 160 160 163.6 4 162.6 AR 440 440 447 445
AR 38 38 39.8 2.3 1.5 39.2 AR 90 90 93 3.4 2.5 92 AR 163 163 166.6 4 2.5 165.6
AR 39 39 40.8 2.3 1.5 40.2 AR 92 92 95 3.4 2.5 94 AR 165 165 168.6 4 2.5 167.6

1N=0.102kgf=0.2248lbs.
L21 1mm=0.03937inch
L22
 ■ Use as Full-complement Bearings
For normal rotation, Needle Roller Bearings with cage
are most suitable, but for low rotational speeds and
for oscillating movement, full-complement bearings
are also used.
If Needle Rollers are combined with a shaft and a
housing which have been hardened and ground to

■ Features ■ Accuracy
form a suitable raceway surface, the combined
assembly can be used as a full-complement bearing
The dimensional accuracy of Needle Rollers conforms which has a large load capacity and a low sectional
Needle Rollers are made of high carbon chromi-
um bearing steel. They are rigid and highly accurate to JIS B 1506 (Rolling bearings-Rollers), and is shown height. (See page A44, Design of shaft and housing.)
and are finished to a hardness of 58HRC or more in Table 3. Normally in this case, the radial clearance is made a
(See Table 1.) and a surface roughness of 0.1 μmRa The selective classification for the mean diameter tol- little larger than that of a bearing with cage and the
or less. erance is shown in Table 4. The selective classifica- circumferential clearance is made to be approximately
These needle rollers are widely used as rolling ele- tion rollers according to Table 4 can be provided as 1/10 of the diameter of needle rollers. When the
ments for bearings, and also as pins and shafts. requested. bearing is used under severe conditions, please con-
Please contact , if Needle Rollers made of stain- tact for further information.
less steel are required.
Table 3 Dimensional accuracy of needle rollers unit: μ m

Diameter varia- Circularity（1） Gauge lot diameter Deviation of

tion in a single variation（1） a single
Table 1 Hardness length（2）
Class radial plane（1）
Nominal diameterDw  mm Hardness VDwp ∆R VDwL ∆ Lws
(Max.) (Max.) (Max.)
Over Incl. HRC HV
− 3 (60 〜 67) 697 〜 900 2 1 1 2 h13
3 − 58 〜 66 (653 〜 865) 3 1.5 1.5 3 h13
Remarks1.　Hardness is flat surface hardness. 5 2 2.5 5 h13
2.　The values in parentheses are converted values for Notes(1)　Applicable to the measurement at the center of roller
reference. length
(2)　Tolerance is based on the classification according to the
nominal length Lw.

■ End Shapes Remark 　Any measured diameter along the total length of roller
must not be larger than the actual maximum diameter at
the center of roller length by the amount exceeding the
Needle Rollers come in spherical and flat end shapes, values given below.
as shown in Table 2. 　　　　　0.5 μ m for Class 2
　　　　　0.8 μ m for Class 3
Please contact , if other shapes are required. 　　　　　 1 μ m for Class 5

Table 2 Shapes of ends

Table 4 Classification of needle rollers unit: μ m
Type Spherical end Flat end
Classification symbol Tolerance for mean dia.

C  3 　0 〜−   3
B  2 　0 〜−   2
B  4 − 2 〜−   4
Shapes B  6 − 4 〜−   6 L
B  8 − 6 〜−   8
B10 − 8 〜− 10

Symbol A F

1N=0.102kgf=0.2248lbs.
L23 1mm=0.03937inch
L24
 Needle Rollers

Lw

Dw
Roller dia. 1 − 6mm

Nominal dimensions　mm Mass Nominal dimensions　mm Mass Nominal dimensions　mm Mass

(Ref.) (Ref.) (Ref.)

Dw Lw Dw Lw Dw Lw
g g g

1 5.8 0.03 3.5 11.8 0.86 5 15.8 2.3

6.8 0.04 13.8 1 17.8 2.6
7.8 0.05 15.8 1.15 19.8 2.9
9.8 0.06 17.8 1.29 21.8 3.2
19.8 1.44 23.8 3.5
1.5 5.8 0.08 21.8 1.58 25.8 3.8
6.8 0.09 23.8 1.73 27.8 4.1
7.8 0.1 25.8 1.88 29.8 4.4
9.8 0.13 27.8 2.1 31.8 4.7
11.8 0.16 29.8 2.2 34.8 5.2
13.8 0.18 31.8 2.3 37.8 5.6
34.8 2.5 39.8 5.9
2 6.8 0.16 49.8 7.4
7.8 0.19 4 11.8 1.12
9.8 0.23 13.8 1.31 6 17.8 3.9
11.8 0.28 15.8 1.5 19.8 4.3
13.8 0.33 17.8 1.69 21.8 4.8
15.8 0.38 19.8 1.88 23.8 5.2
17.8 0.42 21.8 2.1 25.8 5.5
19.8 0.47 23.8 2.3 27.8 6
25.8 2.5 29.8 6.4
2.5 7.8 0.29 27.8 2.6 34.8 7.5
9.8 0.36 29.8 2.8 39.8 8.6
11.8 0.44 31.8 3 49.8 10.8
13.8 0.51 34.8 3.3 59.8 13
15.8 0.59 37.8 3.6
17.8 0.66 39.8 3.8
19.8 0.73
21.8 0.81 4.5 17.8 2.1
23.8 0.88 19.8 2.4
21.8 2.6
3 9.8 0.52 23.8 2.9
11.8 0.63 25.8 3.1
13.8 0.74 29.8 3.6
15.8 0.84 31.8 3.8
17.8 0.95 34.8 4.2
19.8 1.06 37.8 4.5
21.8 1.16 39.8 4.8
23.8 1.27 44.8 5.4
25.8 1.38
27.8 1.48
29.8 1.59
Remark　For the names of the needle rollers, nominal dimensions are used.
Needle Rollers other than those shown in the dimension table can also be manufactured. Please contact for further information.

L25
● Conversion Table of Units

Comparison table between SI units (system of international units), CGS units and gravitational system of units

Item
Length Mass Time Acceleration Force Stress Pressure Energy Power Temperature Viscosity Kinematic viscosity Magnetic flux Magnetic flux density Magnetic field intensity
System of units
SI units m kg s m/s2 N Pa Pa J W K Pa･s m2/s Wb T A/m
CGS units cm g s Gal dyn dyn/cm2 dyn/cm2 erg erg/s °C P St Mx Gs Oe
Grav. units m kgf･s2/m s m/s2 kgf kgf/m2 kgf/m2 kgf･m kgf･m/s °C kgf･s/m2 m2/s — — —

Conversion rates into SI units

Item Unit name Symbol Conversion rate into SI SI unit name Symbol Item Unit name Symbol Conversion rate into SI SI unit name Symbol

Degree ° π/180 Hydro-column meter mH2O 9 806.65

Angle Minute ’ π/10 800 Radian rad Mercurial column millimeter mmHg 101 325/760
Second ” π/648 000 Pressure Torr Torr 101 325/760 Pascal Pa
Meter m 1 Atmosphere atm 101 325
Micronmeter µ 10-6 Bar bar 105
Length Angstrom Å 10-10 Meter m Erg erg 10-7
X-ray unit ≈1.002 08×10-13 IT calorie calIT 4.186 8
Nautical mile n mile 1852 Energy Kilogram force - meter kgf･m 9.806 65
Joule J
Square meter m2 1 Kilowatt hour kW･h 3.600×106
Area Are a 102 Square meter m2 Horse power hour (French) PS･h ≈2.647 79×106
Hectare ha 104 Electron volt eV ≈1.602 19×10-19

Cubic meter m3 1 Watt W 1

Volume Cubic meter m3 Power Horse power (French) PS ≈735.5 Watt W
Liter l, L 10-3
Kilogram force -meter per second kgf･m/s 9.806 65
Kilogram kg 1
Mass Ton t 103 Kilogram kg Poise P 10-1
Atomic mass unit u ≈1.660 57×10-27 Viscosity Centipoise cP 10-3 Pascal-second Pa･s
Kilogram force-second per square meter kgf･s/m2 9.806 65
Second s 1
min 60 Stokes St 10-4
Minute
s Kinematic viscosity Square meter per second m2/s
Time
Hour h 3 600
Second   Centistokes cSt 10-6
Day d 86 400 Temperature Degree °C ＋273.15 Kelvin K
Meter per second m/s 1 Radioactivity Curie Ci 3.7×1010 Becquerel Bq
Velocity Meter per second m/s
Knot kn 1 852/3 600 Exposure dose Roentgen R 2.58×10-4 Coulomb per kilogram C/kg
Frequency and number of
Cycle s-1 1 Hertz Hz Absorbed dose Rad rad 10-2 Gray Gy
oscillations per time
Dose equivalent Rem rem 10-2 Sievert Sv
Rotational speed Rotation per minute min-1 1/60 Per second s-1
Magnetic flux Maxwell Mx 10-8 Weber Wb
Angular velocity Radian per second rad/s 1 Radian per second rad/s
Gamma γ 10-9
Meter per square second m/s2 1 Magnetic flux density Tesla T
Acceleration Meter per square second m/s2 Gauss Gs 10-4
G G 9.806 65
Magnetic field intensity Oersted Oe 103/4π Ampere per meter A/m
Kilogram force kgf 9.806 65
Force Ton force tf 9 806.65 Newton N Quantity of electricity Coulomb C 1 Coulomb C
dyn 10-5 Electric potential difference Volt V 1 Volt V
M
Dyne
Electrostatic capacity Farad F 1 Farad F
Moment of force Kilogram force-meter kgf･m 9.806 65 Newton-meter N･m (Electric) resistance Ohm Ω 1 Ohm Ω
Kilogram force per square meter kgf/m2 9.806 65 (Electric) conductance Siemens S 1 Siemens S
Stress and pressure Kilogram force per square centimeter kgf/cm2 9.806 65×104 Pascal Pa Inductance Henry H 1 Henry H
Kilogram force per square millimeter kgf/mm2 9.806 65×106 Current Ampere A 1 Ampere A

M33 M34
● Inch-mm Conversion Table 1 inch = 25.4 mm 1 inch = 25.4 mm

inch inch
0” 1” 2” 3” 4” 5” 6” 7” 8” 0” 1” 2” 3” 4” 5” 6” 7” 8”
Fraction Decimal Fraction Decimal

0 25.400 50.800 76.200 101.600 127.000 152.400 177.800 203.200 33 / 64” 0.515625 13.097 38.497 63.897 89.297 114.697 140.097 165.497 190.897 216.297
1 / 64” 0.015625 0.397 25.797 51.197 76.597 101.997 127.397 152.797 178.197 203.597 17 / 32” 0.531250 13.494 38.894 64.294 89.694 115.094 140.494 165.894 191.294 216.694
1 / 32” 0.031250 0.794 26.194 51.594 76.994 102.394 127.794 153.194 178.594 203.994 35 / 64” 0.546875 13.891 39.291 64.691 90.091 115.491 140.891 166.291 191.691 217.091
3 / 64” 0.046875 1.191 26.591 51.991 77.391 102.791 128.191 153.591 178.991 204.391 9 / 16” 0.562500 14.288 39.688 65.088 90.488 115.888 141.288 166.688 192.088 217.488
1 / 16” 0.062500 1.588 26.988 52.388 77.788 103.188 128.588 153.988 179.388 204.788
37 / 64” 0.578125 14.684 40.084 65.484 90.884 116.284 141.684 167.084 192.484 217.884
5 / 64” 0.078125 1.984 27.384 52.784 78.184 103.584 128.984 154.384 179.784 205.184 19 / 32” 0.593750 15.081 40.481 65.881 91.281 116.681 142.081 167.481 192.881 218.281
3 / 32” 0.093750 2.381 27.781 53.181 78.581 103.981 129.381 154.781 180.181 205.581 39 / 64” 0.609375 15.478 40.878 66.278 91.678 117.078 142.478 167.878 193.278 218.678
7 / 64” 0.109375 2.778 28.178 53.578 78.978 104.378 129.778 155.178 180.578 205.978 5 / 8” 0.625000 15.875 41.275 66.675 92.075 117.475 142.875 168.275 193.675 219.075
1 / 8” 0.125000 3.175 28.575 53.975 79.375 104.775 130.175 155.575 180.975 206.375

9 / 64” 0.140625 3.572 28.972 54.372 79.772 105.172 130.572 155.972 181.372 206.772 41 / 64” 0.640625 16.272 41.672 67.072 92.472 117.872 143.272 168.672 194.072 219.472
5 / 32” 0.156250 3.969 29.369 54.769 80.169 105.569 130.969 156.369 181.769 207.169 21 / 32” 0.656250 16.669 42.069 67.469 92.869 118.269 143.669 169.069 194.469 219.869
11 / 64” 0.171875 4.366 29.766 55.166 80.566 105.966 131.366 156.766 182.166 207.566 43 / 64” 0.671875 17.066 42.466 67.866 93.266 118.666 144.066 169.466 194.866 220.266
3 / 16” 0.187500 4.762 30.162 55.562 80.962 106.362 131.762 157.162 182.562 207.962 11 / 16” 0.687500 17.462 42.862 68.262 93.662 119.062 144.462 169.862 195.262 220.662

13 / 64” 0.203125 5.159 30.559 55.959 81.359 106.759 132.159 157.559 182.959 208.359 45 / 64” 0.703125 17.859 43.259 68.659 94.059 119.459 144.859 170.259 195.659 221.059
7 / 32” 0.218750 5.556 30.956 56.356 81.756 107.156 132.556 157.956 183.356 208.756 23 / 32” 0.718750 18.256 43.656 69.056 94.456 119.856 145.256 170.656 196.056 221.456
15 / 64” 0.234375 5.953 31.353 56.753 82.153 107.553 132.953 158.353 183.753 209.153 47 / 64” 0.734375 18.653 44.053 69.453 94.853 120.253 145.653 171.053 196.453 221.853
1 / 4” 0.250000 6.350 31.750 57.150 82.550 107.950 133.350 158.750 184.150 209.550 3 / 4” 0.750000 19.050 44.450 69.850 95.250 120.650 146.050 171.450 196.850 222.250

17 / 64” 0.265625 6.747 32.147 57.547 82.947 108.347 133.747 159.147 184.547 209.947 49 / 64” 0.765625 19.447 44.847 70.247 95.647 121.047 146.447 171.847 197.247 222.647
9 / 32” 0.281250 7.144 32.544 57.944 83.344 108.744 134.144 159.544 184.944 210.344 25 / 32” 0.781250 19.844 45.244 70.644 96.044 121.444 146.844 172.244 197.644 223.044
19 / 64” 0.296875 7.541 32.941 58.341 83.741 109.141 134.541 159.941 185.341 210.741 51 / 64” 0.796875 20.241 45.641 71.041 96.441 121.841 147.241 172.641 198.041 223.441
5 / 16” 0.312500 7.938 33.338 58.738 84.138 109.538 134.938 160.338 185.738 211.138 13 / 16” 0.812500 20.638 46.038 71.438 96.838 122.238 147.638 173.038 198.438 223.838

21 / 64” 0.328125 8.334 33.734 59.134 84.534 109.934 135.334 160.734 186.134 211.534 53 / 64” 0.828125 21.034 46.434 71.834 97.234 122.634 148.034 173.434 198.834 224.234
11 / 32” 0.343750 8.731 34.131 59.531 84.931 110.331 135.731 161.131 186.531 211.931 27 / 32” 0.843750 21.431 46.831 72.231 97.631 123.031 148.431 173.831 199.231 224.631
23 / 64” 0.359375 9.128 34.528 59.928 85.328 110.728 136.128 161.528 186.928 212.328 55 / 64” 0.859375 21.828 47.228 72.628 98.028 123.428 148.828 174.228 199.628 225.028
3 / 8” 0.375000 9.525 34.925 60.325 85.725 111.125 136.525 161.925 187.325 212.725 7 / 8” 0.875000 22.225 47.625 73.025 98.425 123.825 149.225 174.625 200.025 225.425

25 / 64” 0.390625 9.922 35.322 60.722 86.122 111.522 136.922 162.322 187.722 213.122 57 / 64” 0.890625 22.622 48.022 73.422 98.822 124.222 149.622 175.022 200.422 225.822
13 / 32” 0.406250 10.319 35.719 61.119 86.519 111.919 137.319 162.719 188.119 213.519 29 / 32” 0.906250 23.019 48.419 73.819 99.219 124.619 150.019 175.419 200.819 226.219
27 / 64” 0.421875 10.716 36.116 61.516 86.916 112.316 137.716 163.116 188.516 213.916 59 / 64” 0.921875 23.416 48.816 74.216 99.616 125.016 150.416 175.816 201.216 226.616
7 / 16” 0.437500 11.112 36.512 61.912 87.312 112.712 138.112 163.512 188.912 214.312 15 / 16” 0.937500 23.812 49.212 74.612 100.012 125.412 150.812 176.212 201.612 227.012

29 / 64” 0.453125 11.509 36.909 62.309 87.709 113.109 138.509 163.909 189.309 214.709 61 / 64” 0.953125 24.209 49.609 75.009 100.409 125.809 151.209 176.609 202.009 227.409
15 / 32” 0.468750 11.906 37.306 62.706 88.106 113.506 138.906 164.306 189.706 215.106 31 / 32” 0.968750 24.606 50.006 75.406 100.806 126.206 151.606 177.006 202.406 227.806
31 / 64” 0.484375 12.303 37.703 63.103 88.503 113.903 139.303 164.703 190.103 215.503 63 / 64” 0.984375 25.003 50.403 75.803 101.203 126.603 152.003 177.403 202.803 228.203
1 / 2” 0.500000 12.700 38.100 63.500 88.900 114.300 139.700 165.100 190.500 215.900

M35 M36
● Hardness Conversion Table (Reference)
Rockwell C Vickers' hardness Brinell hardness Rockwell hardness Shore hardness Rockwell C Vickers' hardness Brinell hardness Rockwell hardness Shore hardness
scale hardness scale hardness
Load 1471N Load 1471N
A scale B scale A scale B scale
Standard ball Tungsten Load 588.4N Load 980.7N Standard ball Tungsten Load 588.4N Load 980.7N
HRC HV carbide ball Diamond circular cone 1/16" ball HS HRC HV carbide ball Diamond circular cone 1/16" ball HS

68 940 — — 85.6 — 97
38 372 353 353 69.4 — 51
67 900 — — 85.0 — 95
37 363 344 344 68.9 — 50
66 865 — — 84.5 — 92
36 354 336 336 68.4 (109.0) 49
65 832 — (739) 83.9 — 91
35 345 327 327 67.9 (108.5) 48
64 800 — (722) 83.4 — 88
34 336 319 319 67.4 (108.0) 47

63 772 — (705) 82.8 — 87

33 327 311 311 66.8 (107.5) 46
62 746 — (688) 82.3 — 85
32 318 301 301 66.3 (107.0) 44
61 720 — (670) 81.8 — 83
31 310 294 294 65.8 (106.0) 43
60 697 — (654) 81.2 — 81
30 302 286 286 65.3 (105.5) 42
59 674 — (634) 80.7 — 80
29 294 279 279 64.7 (104.5) 41

58 653 — 615 80.1 — 78

28 286 271 271 64.3 (104.0) 41
57 633 — 595 79.6 — 76
27 279 264 264 63.8 (103.0) 40
56 613 — 577 79.0 — 75
26 272 258 258 63.3 (102.5) 38
55 595 — 560 78.5 — 74
25 266 253 253 62.8 (101.5) 38
54 577 — 543 78.0 — 72
24 260 247 247 62.4 (101.0) 37

53 560 — 525 77.4 — 71

23 254 243 243 62.0 100.0 36
52 544 (500) 512 76.8 — 69
22 248 237 237 61.5 99.0 35
51 528 (487) 496 76.3 — 68
21 243 231 231 61.0 98.5 35
50 513 (475) 481 75.9 — 67
20 238 226 226 60.5 97.8 34
49 498 (464) 469 75.2 — 66

(18) 230 219 219 — 96.7 33

48 484 451 455 74.7 — 64
(16) 222 212 212 — 95.5 32
47 471 442 443 74.1 — 63
(14) 213 203 203 — 93.9 31
46 458 432 432 73.6 — 62
(12) 204 194 194 — 92.3 29
45 446 421 421 73.1 — 60
44 434 409 409 72.5 — 58
(10) 196 187 187 — 90.7 28
(8) 188 179 179 — 89.5 27
43 423 400 400 72.0 — 57
(6) 180 171 171 — 87.1 26
42 412 390 390 71.5 — 56
(4) 173 165 165 — 85.5 25
41 402 381 381 70.9 — 55
(2) 166 158 158 — 83.5 24
40 392 371 371 70.4 — 54
(0) 160 152 152 — 81.7 24
39 382 362 362 69.9 — 52

M37 M38
● Tolerance of Shaft Diameter unit : μm

Nominal Diameter Nominal Diameter

b12 c12 d6 e6 e12 f5 f6 g5 g6 h5 h6 h7 h8 h9 h10 h11
mm mm

Over Incl. High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low Over Incl.

— 3 −140 − 240 − 60 − 160 − 20 − 26 − 14 − 20 − 14 −114 − 6 −10 − 6 − 12 − 2 − 6 − 2 − 8 0 − 4 0 − 6 0 −10 0 −14 0 − 25 0 − 40 0 − 60 — 3

3 6 −140 − 260 − 70 − 190 − 30 − 38 − 20 − 28 − 20 −140 −10 −15 −10 − 18 − 4 − 9 − 4 −12 0 − 5 0 − 8 0 −12 0 −18 0 − 30 0 − 48 0 − 75 3 6
6 10 −150 − 300 − 80 − 230 − 40 − 49 − 25 − 34 − 25 −175 −13 −19 −13 − 22 − 5 −11 − 5 −14 0 − 6 0 − 9 0 −15 0 −22 0 − 36 0 − 58 0 − 90 6 10
10 18 −150 − 330 − 95 − 275 − 50 − 61 − 32 − 43 − 32 −212 −16 −24 −16 − 27 − 6 −14 − 6 −17 0 − 8 0 −11 0 −18 0 −27 0 − 43 0 − 70 0 −110 10 18
18 30 −160 − 370 −110 − 320 − 65 − 78 − 40 − 53 − 40 −250 −20 −29 −20 − 33 − 7 −16 − 7 −20 0 − 9 0 −13 0 −21 0 −33 0 − 52 0 − 84 0 −130 18 30
30 40 −170 − 420 −120 − 370 30 40
− 80 − 96 − 50 − 66 − 50 −300 −25 −36 −25 − 41 − 9 −20 − 9 −25 0 −11 0 −16 0 −25 0 −39 0 − 62 0 −100 0 −160
40 50 −180 − 430 −130 − 380 40 50
50 65 −190 − 490 −140 − 440 50 65
−100 −119 − 60 − 79 − 60 −360 −30 −43 −30 − 49 −10 −23 −10 −29 0 −13 0 −19 0 −30 0 −46 0 − 74 0 −120 0 −190
65 80 −200 − 500 −150 − 450 65 80
80 100 −220 − 570 −170 − 520 80 100
−120 −142 − 72 − 94 − 72 −422 −36 −51 −36 − 58 −12 −27 −12 −34 0 −15 0 −22 0 −35 0 −54 0 − 87 0 −140 0 −220
100 120 −240 − 590 −180 − 530 100 120
120 140 −260 − 660 −200 − 600 120 140
140 160 −280 − 680 −210 − 610 −145 −170 − 85 −110 − 85 −485 −43 −61 −43 − 68 −14 −32 −14 −39 0 −18 0 −25 0 −40 0 −63 0 −100 0 −160 0 −250 140 160
160 180 −310 − 710 −230 − 630 160 180
180 200 −340 − 800 −240 − 700 180 200
200 225 −380 − 840 −260 − 720 −170 −199 −100 −129 −100 −560 −50 −70 −50 − 79 −15 −35 −15 −44 0 −20 0 −29 0 −46 0 −72 0 −115 0 −185 0 −290 200 225
225 250 −420 − 880 −280 − 740 225 250
250 280 −480 −1000 −300 − 820 250 280
−190 −222 −110 −142 −110 −630 −56 −79 −56 − 88 −17 −40 −17 −49 0 −23 0 −32 0 −52 0 −81 0 −130 0 −210 0 −320
280 315 −540 −1060 −330 − 850 280 315
315 355 −600 −1170 −360 − 930 315 355
−210 −246 −125 −161 −125 −695 −62 −87 −62 − 98 −18 −43 −18 −54 0 −25 0 −36 0 −57 0 −89 0 −140 0 −230 0 −360
355 400 −680 −1250 −400 − 970 355 400
400 450 −760 −1390 −440 −1070 400 450
−230 −270 −135 −175 −135 −765 −68 −95 −68 −108 −20 −47 −20 −60 0 −27 0 −40 0 −63 0 −97 0 −155 0 −250 0 −400
450 500 −840 −1470 −480 −1110 450 500

unit : μm

Nominal Diameter Nominal Diameter

h12 h13 js5 j5 js6 j6 j7 k5 k6 m5 m6 n5 n6 p6
mm mm

Over Incl. High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low Over Incl.

— 3 0 −100 0 −140 ＋ 2 − 2 ＋2 − 2 ＋ 3 − 3 ＋ 4 − 2 ＋ 6 − 4 ＋ 4  0 ＋ 6  0 ＋ 6 ＋ 2 ＋ 8 ＋ 2 ＋ 8 ＋ 4 ＋10 ＋ 4 ＋ 12 ＋ 6 — 3

3 6 0 −120 0 −180 ＋ 2.5 − 2.5 ＋3 − 2 ＋ 4 − 4 ＋ 6 − 2 ＋ 8 − 4 ＋ 6 ＋1 ＋ 9 ＋1 ＋ 9 ＋ 4 ＋12 ＋ 4 ＋13 ＋ 8 ＋16 ＋ 8 ＋ 20 ＋12 3 6
6 10 0 −150 0 −220 ＋ 3 − 3 ＋4 − 2 ＋ 4.5 − 4.5 ＋ 7 − 2 ＋10 − 5 ＋ 7 ＋1 ＋10 ＋1 ＋12 ＋ 6 ＋15 ＋ 6 ＋16 ＋10 ＋19 ＋10 ＋ 24 ＋15 6 10
10 18 0 −180 0 −270 ＋ 4 − 4 ＋5 − 3 ＋ 5.5 − 5.5 ＋ 8 − 3 ＋12 − 6 ＋ 9 ＋1 ＋12 ＋1 ＋15 ＋ 7 ＋18 ＋ 7 ＋20 ＋12 ＋23 ＋12 ＋ 29 ＋18 10 18
18 30 0 −210 0 −330 ＋ 4.5 − 4.5 ＋5 − 4 ＋ 6.5 − 6.5 ＋ 9 − 4 ＋13 − 8 ＋11 ＋2 ＋15 ＋2 ＋17 ＋ 8 ＋21 ＋ 8 ＋24 ＋15 ＋28 ＋15 ＋ 35 ＋22 18 30
30 40 30 40
0 −250 0 −390 ＋ 5.5 − 5.5 ＋6 − 5 ＋ 8 − 8 ＋11 − 5 ＋15 −10 ＋13 ＋2 ＋18 ＋2 ＋20 ＋ 9 ＋25 ＋ 9 ＋28 ＋17 ＋33 ＋17 ＋ 42 ＋26
40 50 40 50
50 65 50 65
0 −300 0 −460 ＋ 6.5 − 6.5 ＋6 − 7 ＋ 9.5 − 9.5 ＋12 − 7 ＋18 −12 ＋15 ＋2 ＋21 ＋2 ＋24 ＋11 ＋30 ＋11 ＋33 ＋20 ＋39 ＋20 ＋ 51 ＋32
65 80 65 80
80 100 80 100
0 −350 0 −540 ＋ 7.5 − 7.5 ＋6 − 9 ＋11 −11 ＋13 − 9 ＋20 −15 ＋18 ＋3 ＋25 ＋3 ＋28 ＋13 ＋35 ＋13 ＋38 ＋23 ＋45 ＋23 ＋ 59 ＋37
100 120 100 120
120 140 120 140
140 160 0 −400 0 −630 ＋ 9 − 9 ＋7 −11 ＋12.5 −12.5 ＋14 −11 ＋22 −18 ＋21 ＋3 ＋28 ＋3 ＋33 ＋15 ＋40 ＋15 ＋45 ＋27 ＋52 ＋27 ＋ 68 ＋43 140 160
160 180 160 180
180 200 180 200
200 225 0 −460 0 −720 ＋10 −10 ＋7 −13 ＋14.5 −14.5 ＋16 −13 ＋25 −21 ＋24 ＋4 ＋33 ＋4 ＋37 ＋17 ＋46 ＋17 ＋51 ＋31 ＋60 ＋31 ＋ 79 ＋50 200 225
225 250 225 250
250 280 250 280

M
0 −520 0 −810 ＋11.5 −11.5 ＋7 −16 ＋16 −16 ＋16 −16 ＋26 −26 ＋27 ＋4 ＋36 ＋4 ＋43 ＋20 ＋52 ＋20 ＋57 ＋34 ＋66 ＋34 ＋ 88 ＋56
280 315 280 315
315 355 315 355
0 −570 0 −890 ＋12.5 −12.5 ＋7 −18 ＋18 −18 ＋18 −18 ＋29 −28 ＋29 ＋4 ＋40 ＋4 ＋46 ＋21 ＋57 ＋21 ＋62 ＋37 ＋73 ＋37 ＋ 98 ＋62
355 400 355 400
400 450 400 450
0 −630 0 −970 ＋13.5 −13.5 ＋7 −20 ＋20 −20 ＋20 −20 ＋31 −32 ＋32 ＋5 ＋45 ＋5 ＋50 ＋23 ＋63 ＋23 ＋67 ＋40 ＋80 ＋40 ＋108 ＋68
450 500 450 500

M39 M40
● Tolerance of Housing Bore Diameter unit : μm

Nominal Diameter Nominal Diameter

B12 E7 E11 E12 F6 F7 G6 G7 H6 H7 H8 H9 H10 H11 JS6 J6
mm mm

Over Incl. High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low Over Incl.

— 3 ＋ 240 ＋140 ＋ 24 ＋ 14 ＋ 74 ＋ 14 ＋114 ＋ 14 ＋ 12 ＋ 6 ＋ 16 ＋ 6 ＋ 8 ＋ 2 ＋12 ＋ 2 ＋ 6 0 ＋10 0 ＋14 0 ＋ 25 0 ＋ 40 0 ＋ 60 0 ＋ 3 − 3 ＋ 2 −4 — 3

3 6 ＋ 260 ＋140 ＋ 32 ＋ 20 ＋ 95 ＋ 20 ＋140 ＋ 20 ＋ 18 ＋10 ＋ 22 ＋10 ＋12 ＋ 4 ＋16 ＋ 4 ＋ 8 0 ＋12 0 ＋18 0 ＋ 30 0 ＋ 48 0 ＋ 75 0 ＋ 4 − 4 ＋ 5 −3 3 6
6 10 ＋ 300 ＋150 ＋ 40 ＋ 25 ＋115 ＋ 25 ＋175 ＋ 25 ＋ 22 ＋13 ＋ 28 ＋13 ＋14 ＋ 5 ＋20 ＋ 5 ＋ 9 0 ＋15 0 ＋22 0 ＋ 36 0 ＋ 58 0 ＋ 90 0 ＋ 4.5 − 4.5 ＋ 5 −4 6 10
10 18 ＋ 330 ＋150 ＋ 50 ＋ 32 ＋142 ＋ 32 ＋212 ＋ 32 ＋ 27 ＋16 ＋ 34 ＋16 ＋17 ＋ 6 ＋24 ＋ 6 ＋11 0 ＋18 0 ＋27 0 ＋ 43 0 ＋ 70 0 ＋110 0 ＋ 5.5 − 5.5 ＋ 6 −5 10 18
18 30 ＋ 370 ＋160 ＋ 61 ＋ 40 ＋170 ＋ 40 ＋250 ＋ 40 ＋ 33 ＋20 ＋ 41 ＋20 ＋20 ＋ 7 ＋28 ＋ 7 ＋13 0 ＋21 0 ＋33 0 ＋ 52 0 ＋ 84 0 ＋130 0 ＋ 6.5 − 6.5 ＋ 8 −5 18 30
30 40 ＋ 420 ＋170 30 40
＋ 75 ＋ 50 ＋210 ＋ 50 ＋300 ＋ 50 ＋ 41 ＋25 ＋ 50 ＋25 ＋25 ＋ 9 ＋34 ＋ 9 ＋16 0 ＋25 0 ＋39 0 ＋ 62 0 ＋100 0 ＋160 0 ＋ 8 − 8 ＋10 −6
40 50 ＋ 430 ＋180 40 50
50 65 ＋ 490 ＋190 50 65
＋ 90 ＋ 60 ＋250 ＋ 60 ＋360 ＋ 60 ＋ 49 ＋30 ＋ 60 ＋30 ＋29 ＋10 ＋40 ＋10 ＋19 0 ＋30 0 ＋46 0 ＋ 74 0 ＋120 0 ＋190 0 ＋ 9.5 − 9.5 ＋13 −6
65 80 ＋ 500 ＋200 65 80
80 100 ＋ 570 ＋220 80 100
＋107 ＋ 72 ＋292 ＋ 72 ＋422 ＋ 72 ＋ 58 ＋36 ＋ 71 ＋36 ＋34 ＋12 ＋47 ＋12 ＋22 0 ＋35 0 ＋54 0 ＋ 87 0 ＋140 0 ＋220 0 ＋11 −11 ＋16 −6
100 120 ＋ 590 ＋240 100 120
120 140 ＋ 660 ＋260 120 140
140 160 ＋ 680 ＋280 ＋125 ＋ 85 ＋335 ＋ 85 ＋485 ＋ 85 ＋ 68 ＋43 ＋ 83 ＋43 ＋39 ＋14 ＋54 ＋14 ＋25 0 ＋40 0 ＋63 0 ＋100 0 ＋160 0 ＋250 0 ＋12.5 −12.5 ＋18 −7 140 160
160 180 ＋ 710 ＋310 160 180
180 200 ＋ 800 ＋340 180 200
200 225 ＋ 840 ＋380 ＋146 ＋100 ＋390 ＋100 ＋560 ＋100 ＋ 79 ＋50 ＋ 96 ＋50 ＋44 ＋15 ＋61 ＋15 ＋29 0 ＋46 0 ＋72 0 ＋115 0 ＋185 0 ＋290 0 ＋14.5 −14.5 ＋22 −7 200 225
225 250 ＋ 880 ＋420 225 250
250 280 ＋1000 ＋480 250 280
＋162 ＋110 ＋430 ＋110 ＋630 ＋110 ＋ 88 ＋56 ＋108 ＋56 ＋49 ＋17 ＋69 ＋17 ＋32 0 ＋52 0 ＋81 0 ＋130 0 ＋210 0 ＋320 0 ＋16 −16 ＋25 −7
280 315 ＋1060 ＋540 280 315
315 355 ＋1170 ＋600 315 355
＋182 ＋125 ＋485 ＋125 ＋695 ＋125 ＋ 98 ＋62 ＋119 ＋62 ＋54 ＋18 ＋75 ＋18 ＋36 0 ＋57 0 ＋89 0 ＋140 0 ＋230 0 ＋360 0 ＋18 −18 ＋29 −7
355 400 ＋1250 ＋680 355 400
400 450 ＋1390 ＋760 400 450
＋198 ＋135 ＋535 ＋135 ＋765 ＋135 ＋108 ＋68 ＋131 ＋68 ＋60 ＋20 ＋83 ＋20 ＋40 0 ＋63 0 ＋97 0 ＋155 0 ＋250 0 ＋400 0 ＋20 −20 ＋33 −7
450 500 ＋1470 ＋840 450 500

unit : μm

Nominal Diameter Nominal Diameter

JS7 J7 K5 K6 K7 M6 M7 N6 N7 P6 P7 R7 S7
mm mm

Over Incl. High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low Over Incl.

— 3 ＋ 5 − 5 ＋ 4 − 6  0 − 4  0 − 6   0 −10 − 2 − 8 −2 −12 − 4 −10 − 4 −14 − 6 −12 − 6 − 16 − 10 − 20 − 14 − 24 — 3

3 6 ＋ 6 − 6 ＋ 6 − 6  0 − 5 ＋2 − 6 ＋ 3 − 9 − 1 − 9  0 −12 − 5 −13 − 4 −16 − 9 −17 − 8 − 20 − 11 − 23 − 15 − 27 3 6
6 10 ＋ 7 − 7 ＋ 8 − 7 ＋1 − 5 ＋2 − 7 ＋ 5 −10 − 3 −12  0 −15 − 7 −16 − 4 −19 −12 −21 − 9 − 24 − 13 − 28 − 17 − 32 6 10
10 18 ＋ 9 − 9 ＋10 − 8 ＋2 − 6 ＋2 − 9 ＋ 6 −12 − 4 −15  0 −18 − 9 −20 − 5 −23 −15 −26 −11 − 29 − 16 − 34 − 21 − 39 10 18
18 30 ＋10 −10 ＋12 − 9 ＋1 − 8 ＋2 −11 ＋ 6 −15 − 4 −17  0 −21 −11 −24 − 7 −28 −18 −31 −14 − 35 − 20 − 41 − 27 − 48 18 30
30 40 30 40
＋12 −12 ＋14 −11 ＋2 − 9 ＋3 −13 ＋ 7 −18 − 4 −20  0 −25 −12 −28 − 8 −33 −21 −37 −17 − 42 − 25 − 50 − 34 − 59
40 50 40 50
50 65 − 30 − 60 − 42 − 72 50 65
＋15 −15 ＋18 −12 ＋3 −10 ＋4 −15 ＋ 9 −21 − 5 −24  0 −30 −14 −33 − 9 −39 −26 −45 −21 − 51
65 80 − 32 − 62 − 48 − 78 65 80
80 100 − 38 − 73 − 58 − 93 80 100
＋17 −17 ＋22 −13 ＋2 −13 ＋4 −18 ＋10 −25 − 6 −28  0 −35 −16 −38 −10 −45 −30 −52 −24 − 59
100 120 − 41 − 76 − 66 − 101 100 120
120 140 − 48 − 88 − 77 −117 120 140
140 160 ＋20 −20 ＋26 −14 ＋3 −15 ＋4 −21 ＋12 −28 − 8 −33  0 −40 −20 −45 −12 −52 −36 −61 −28 − 68 − 50 − 90 − 85 −125 140 160
160 180 − 53 − 93 − 93 −133 160 180
180 200 − 60 −106 −105 −151 180 200
200 225 ＋23 −23 ＋30 −16 ＋2 −18 ＋5 −24 ＋13 −33 − 8 −37  0 −46 −22 −51 −14 −60 −41 −70 −33 − 79 − 63 −109 −113 −159 200 225
225 250 − 67 −113 −123 −169 225 250
250 280 − 74 −126 −138 −190 250 280

M
＋26 −26 ＋36 −16 ＋3 −20 ＋5 −27 ＋16 −36 − 9 −41  0 −52 −25 −57 −14 −66 −47 −79 −36 − 88
280 315 − 78 −130 −150 −202 280 315
315 355 − 87 −144 −169 −226 315 355
＋28 −28 ＋39 −18 ＋3 −22 ＋7 −29 ＋17 −40 −10 −46  0 −57 −26 −62 −16 −73 −51 −87 −41 − 98
355 400 − 93 −150 −187 −244 355 400
400 450 −103 −166 −209 −272 400 450
＋31 −31 ＋43 −20 ＋2 −25 ＋8 −32 ＋18 −45 −10 −50  0 −63 −27 −67 −17 −80 −55 −95 −45 −108
450 500 −109 −172 −229 −292 450 500

M41 M42
● N-lbf Conversion Table 1N = 0.224809 lbf 1lbf = 4.44822 N
● N-kgf Conversion Table 1N = 0.1019716 kgf 1kgf = 9.80665 N

N lbf N lbf N lbf N kgf N kgf N kgf

4.448 1 0.225 151.24 34 7.643 298.03 67 15.062 9.8066 1 0.1020 333.43 34 3.4670 657.05 67 6.8321
8.896 2 0.450 155.69 35 7.868 302.48 68 15.287 19.613 2 0.2039 343.23 35 3.5690 666.85 68 6.9341
13.345 3 0.674 160.14 36 8.093 306.93 69 15.512 29.420 3 0.3059 353.04 36 3.6710 676.66 69 7.0360
17.793 4 0.899 164.58 37 8.318 311.38 70 15.737 39.227 4 0.4079 362.85 37 3.7729 686.47 70 7.1380
22.241 5 1.124 169.03 38 8.543 315.82 71 15.961 49.033 5 0.5099 372.65 38 3.8749 696.27 71 7.2400

26.689 6 1.349 173.48 39 8.768 320.27 72 16.186 58.840 6 0.6118 382.46 39 3.9769 706.08 72 7.3420
31.138 7 1.574 177.93 40 8.992 324.72 73 16.411 68.647 7 0.7138 392.27 40 4.0789 715.89 73 7.4439
35.586 8 1.798 182.38 41 9.217 329.17 74 16.636 78.453 8 0.8158 402.07 41 4.1808 725.69 74 7.5459
40.034 9 2.023 186.83 42 9.442 333.62 75 16.861 88.260 9 0.9177 411.88 42 4.2828 735.50 75 7.6479
44.482 10 2.248 191.27 43 9.667 338.06 76 17.085 98.066 10 1.0197 421.69 43 4.3848 745.31 76 7.7498

48.930 11 2.473 195.72 44 9.892 342.51 77 17.310 107.87 11 1.1217 431.49 44 4.4868 755.11 77 7.8518
53.379 12 2.698 200.17 45 10.116 346.96 78 17.535 117.68 12 1.2237 441.30 45 4.5887 764.92 78 7.9538
57.827 13 2.923 204.62 46 10.341 351.41 79 17.760 127.49 13 1.3256 451.11 46 4.6907 774.73 79 8.0558
62.275 14 3.147 209.07 47 10.566 355.86 80 17.985 137.29 14 1.4276 460.91 47 4.7927 784.53 80 8.1577
66.723 15 3.372 213.51 48 10.791 360.31 81 18.210 147.10 15 1.5296 470.72 48 4.8946 794.34 81 8.2597

71.171 16 3.597 217.96 49 11.016 364.75 82 18.434 156.91 16 1.6315 480.53 49 4.9966 804.15 82 8.3617
75.620 17 3.822 222.41 50 11.240 369.20 83 18.659 166.71 17 1.7335 490.33 50 5.0986 813.95 83 8.4636
80.068 18 4.047 226.86 51 11.465 373.65 84 18.884 176.52 18 1.8355 500.14 51 5.2006 823.76 84 8.5656
84.516 19 4.271 231.31 52 11.690 378.10 85 19.109 186.33 19 1.9375 509.95 52 5.3025 833.57 85 8.6676
88.964 20 4.496 235.76 53 11.915 382.55 86 19.334 196.13 20 2.0394 519.75 53 5.4045 843.37 86 8.7696

93.413 21 4.721 240.20 54 12.140 386.99 87 19.558 205.94 21 2.1414 529.56 54 5.5065 853.18 87 8.8715
97.861 22 4.946 244.65 55 12.364 391.44 88 19.783 215.75 22 2.2434 539.37 55 5.6084 862.99 88 8.9735
102.31 23 5.171 249.10 56 12.589 395.89 89 20.008 225.55 23 2.3453 549.17 56 5.7104 872.79 89 9.0755
106.76 24 5.395 253.55 57 12.814 400.34 90 20.233 235.36 24 2.4473 558.98 57 5.8124 882.60 90 9.1774
111.21 25 5.620 258.00 58 13.039 404.79 91 20.458 245.17 25 2.5493 568.79 58 5.9144 892.41 91 9.2794

115.65 26 5.845 262.44 59 13.264 409.24 92 20.682 254.97 26 2.6513 578.59 59 6.0163 902.21 92 9.3814
120.10 27 6.070 266.89 60 13.489 413.68 93 20.907 264.78 27 2.7532 588.40 60 6.1183 912.02 93 9.4834
124.55 28 6.295 271.34 61 13.713 418.13 94 21.132 274.59 28 2.8552 598.21 61 6.2203 921.83 94 9.5853
129.00 29 6.519 275.79 62 13.938 422.58 95 21.357 284.39 29 2.9572 608.01 62 6.3222 931.63 95 9.6873
133.45 30 6.744 280.24 63 14.163 427.03 96 21.582 294.20 30 3.0591 617.82 63 6.4242 941.44 96 9.7893

137.89 31 6.969 284.69 64 14.388 431.48 97 21.806 304.01 31 3.1611 627.63 64 6.5262 951.25 97 9.8912
142.34 32 7.194 289.13 65 14.613 435.93 98 22.031 313.81 32 3.2631 637.43 65 6.6282 961.05 98 9.9932
146.79 33 7.419 293.58 66 14.837 440.37 99 22.256 323.62 33 3.3651 647.24 66 6.7301 970.86 99 10.0952
How to use : For example, to convert 20 N into lbf, find the number 20 in the center of the first column. By referring to the lbf column on the right, it will How to use : For example, to convert 20 N into kgf, find the number 20 in the center of the first column. By referring to the kgf column on the right, it
be found that 20 N equals 4.496 lbf. will be found that 20 N equals 2.0394 kgf.
To convert 20 lbf into N, refer to the N column on the left and it will be found that 20 lbf equals 88.964 N. To convert 20 kgf into N, refer to the N column on the left and it will be found that 20 kgf equals 196.13 N.

M43 M44
 9−5
5−9
● Temperature Conversion Table C = (F-32) F = 32+ C ● Grease names and the characteristics (Reference)
Thickener Con- Dropping Service
˚C ˚F ˚C ˚F ˚C ˚F ˚C ˚F

Sor t
Name Supplier of metallic sistency point range( 1 ) Remarks
soap (˚C) (˚C)

-73.3 -100 -148.0 -2.2 28 82.4 16.1 61 141.8 34.4 94 201.2 ALVANIA GREASE S1 SHELL Li 323 182 −35∼＋120 General, Centralized greasing
-62.2 - 80 -112.0 -1.7 29 84.2 16.7 62 143.6 35.0 95 203.0
-51.1 - 60 - 76.0 -1.1 30 86.0 17.2 63 145.4 35.6 96 204.8 ALVANIA GREASE S2 SHELL Li 283 185 −25∼＋120 General, Centralized greasing

General purpose
-40.0 - 40 - 40.0 -0.6 31 87.8 17.8 64 147.2 36.1 97 206.6 ALVANIA GREASE S3 SHELL Li 242 185 −20∼＋135 General
-28.9 - 20 - 4.0 0 32 89.6 18.3 65 149.0 36.7 98 208.4
DAPHNE EPONEX GREASE No.2 IDEMITSU Li 276 195 −20∼＋120 General

-17.8 0 32.0 0.6 33 91.4 18.9 66 150.8 37.2 99 210.2 COSMO GREASE DYNAMAX No.2 COSMO Li 280 188 −20∼＋120 General
-17.2 1 33.8 1.1 34 93.2 19.4 67 152.6 37.8 100 212
-16.7 2 35.6 1.7 35 95.0 20.0 68 154.4 43.3 110 230 MULTINOC GREASE 2 NIPPON OIL Li 278 212 −30∼＋125 General

-16.1 3 37.4 2.2 36 96.8 20.6 69 156.2 48.9 120 248 MOBILAX GREASE No.2 MOBIL Li 280 196 −35∼＋120 General
-15.6 4 39.2 2.8 37 98.6 21.1 70 158.0 54.4 130 266
ALVANIA GREASE RA-J SHELL Li 252 183 −40∼＋130 Low temperature

Low temperature
-15.0 5 41.0 3.3 38 100.4 21.7 71 159.8 60.0 140 284 （＋160）
BEACON 325 ESSO Li 280 193 −60∼＋120 Low temperature, Low torque
-14.4 6 42.8 3.9 39 102.2 22.2 72 161.6 65.6 150 302 Low temperature, High 
-13.9 7 44.6 4.4 40 104.0 22.8 73 163.4 71.1 160 320 ISOFLEX LDS 18 SPECIAL A KLÜBER Li 280 ≧185 −60∼＋130 speed,Extreme pressure
8 41 74 170 Low temperature, High
-13.3 46.4 5.0 105.8 23.3 165.2 76.7 338 ISOFLEX SUPER LDS 18 KLÜBER Li 280 ≧185 −60∼＋130 speed,Low noise
-12.8 9 48.2 5.6 42 107.6 23.9 75 167.0 82.2 180 356
LT GREASE No.2 JAPAN ENERGY Li 275 181 −50∼＋150 Low temperature

-12.2 10 50.0 6.1 43 109.4 24.4 76 168.8 87.8 190 374 ≧300 （＋200） Wide temperature range, High

Wide temperature range

TEMPREX N3 ESSO Li Complex 235 −20∼＋160 temperature
-11.7 11 51.8 6.7 44 111.2 25.0 77 170.6 93.3 200 392 Wide temperature range, Low
-11.1 12 53.6 7.2 45 113.0 25.6 78 172.4 121.1 250 482 AEROSHELL GREASE 7 SHELL Microgel 288 ≧260 −73∼＋149 temperature
13 46 79 300 Wide temperature range, For low
-10.6 55.4 7.8 114.8 26.1 174.2 149 572 MULTEMP PS No.2 KYODO YUSHI Li 275 190 −50∼＋130 temperature & low noise
-10.0 14 57.2 8.3 47 116.6 26.7 80 176.0 177 350 662 Wide temperature range, For low
MULTEMP SRL KYODO YUSHI Li 242 192 −50∼＋150 temperature & low noise
- 9.4 15 59.0 8.9 48 118.4 27.2 81 177.8 204 400 752 MULTINOC WIDE No.2 NIPPON OIL Li+special Na 247 203 −40∼＋135 Wide temperature range
- 8.9 16 60.8 9.4 49 120.2 27.8 82 179.6 232 450 842 Extreme pressure, Centralized
- 8.3 17 62.6 10.0 50 122.0 28.3 83 181.4 260 500 932 ALVANIA EP GREASE 2 SHELL Li 276 187 −20∼＋110 greasing

pressure
Extreme
- 7.8 18 64.4 10.6 51 123.8 28.9 84 183.2 288 550 1022 MOLYKOTE BR2-PLUS DOW CORNING Li 265 185 −30∼＋150 With MoS2, Extreme pressure
- 7.2 19 66.2 11.1 52 125.6 29.4 85 185.0 316 600 1112
MOLUB-ALLOY #777-2 CASTROL Li 280 182 0∼＋135 With MoS2, Extreme pressure

20 53 86 650 Wide temperatur range, Superior at high

- 6.7 68.0 11.7 127.4 30.0 186.8 343 1202
G 40M SHIN-ETSU Li 260 ≧200 −30∼＋200 temperature with stable anti-oxidation
- 6.1 21 69.8 12.2 54 129.2 30.6 87 188.6 371 700 1292 and water proof, Chemically inert
Wide temperatur range, Superior at high
- 5.6 22 71.6 12.8 55 131.0 31.1 88 190.4 399 750 1382 G 40H SHIN-ETSU Li 220 ≧200 −30∼＋200 temperature with stable anti-oxidation
- 5.0 23 73.4 13.3 56 132.8 31.7 89 192.2 427 800 1472 and water proof, Chemically inert
Stabl at high temperature,
- 4.4 24 75.2 13.9 57 134.6 32.2 90 194.0 454 850 1562 KRYTOX 240AD DU PONT Fluorinated 275 None −30∼＋288 Chemically inert, Anti-solvent
（＋250） General, Low evaporation at high

Others
25 58 91 900 BARRIERTA L55/2 KLÜBER Fluorinated No.2 None −35∼＋220 temperature, Chemically inert
- 3.9 77.0 14.4 136.4 32.8 195.8 482 1652
- 3.3 26 78.8 15.0 59 138.2 33.3 92 197.6 510 950 1742 BARRIERTA IMI/V KLÜBER Fluorinated No.2 None −50∼＋220 For high vacuum
- 2.8 27 80.6 15.6 60 140.0 33.9 93 199.4 538 1000 1832 Stabl at high temperature, Anti-
DEMNUM GREASE L-200 DAIKIN Fluorinated 280 None −60∼＋300 solvent, Chemically inert
How to use : For example, to convert 20˚C into ˚F, find the number 20 in the center of the first column. By referring the ˚F column on the right, it will
Heat resistant, Superior at high
be found that 20˚C equals 68.0˚F. DOLIUM GREASE R SHELL Polyurea 281 249 −30∼＋150 temperature with stable anti-oxidation
To convert 20˚F into ˚C, refer to the ˚C column on the left and it will be found that 20˚F equals -6.7˚C.
Heat resistant, Superior at high
STAMINA GREASE RL2 SHELL Polyurea 268 271 −20∼＋180 temperature with stable anti-oxidation
Note( 1 ) : Figures in parentheses show the maximum allowable temperature in very short time operation, and they are not applicable for continuous
operation.
Remark When using these products, see individual manufacturer's catalogs.

M45 M46
 "Linear Motion Rolling Guide Series" being a leader of
growth and "Mechatronics Series" being a pioneer of
the next generation
Nippon Thompson Co., Ltd. has been developing various products related to
linear motion rolling guides. With their high quality and excellent functional charac-
teristics recognized, is supplying its products to a wide range of different ap-
plications.
The following linear motion rolling guide series and mechatronics series show
a remarkable increase in sales in advanced industries including semiconductor
manufacturing equipment requiring precise positioning, and are also expected to
grow further in the high technology industry.
For details, refer to the "General Catalog for Linear Motion Rolling Guide Series"
and "Catalog of Mechatronics Series".

M47 M48
 Linear Motion Rolling Guide Series, Configuration of General Catalog
Linear Motion Rolling Guide Series General Catalog Consists of BLUE and RED , the two volumes.
（CAT-1574E） （CAT-1575E）

BLUE RED
IKO THOMPSON BRAZIL SERVICE CO.,LTD. (BRAZIL)
【Models】 NIPPON THOMPSON CO., LTD. (JAPAN) IKO THOMPSON BRAZIL SERVICE CO.,LTD. (BRAZIL)
【Models】
Linear Motion Rolling Guide Series Linear Motion Rolling Guide Series
Av.Paulista, 854 10th floor, Top Center, Head Office : 19-13 Takanawa 2-chome Minato-ku Av.Paulista, 854 10th floor, Top Center,
01310-100, Sao Paulo, SP, Brazil Tokyo 108-8586, Japan 01310-100, Sao Paulo, SP, Brazil
Phone : +55 (0)11-2186-0221 Phone : +81 (0)3-3448-5850 Phone : +55 (0)11-2186-0221

●Rail Guide Type ●Rail Guide Type

Fax : +55 (0)11-2186-0299 Fax : +81 (0)3-3447-7637 Fax : +55 (0)11-2186-0299

General Catalog General Catalog

E-mail : [email protected] E-mail : [email protected] E-mail : [email protected]
URL : http://www.ikont.co.jp/eg
Plant : Gifu, Kamakura

NIPPON THOMPSON EUROPE B.V. (EUROPE) IKO THOMPSON KOREA CO.,LTD. (KOREA) IKO INTERNATIONAL, INC. (U.S.A.) NIPPON THOMPSON EUROPE B.V. (EUROPE) IKO THOMPSON KOREA CO.,LTD. (KOREA)
Linear Motion Rolling Guide Series General Catalog BLUE

Linear Motion Rolling Guide Series General Catalog RED

The Netherlands (Sales Head Office)
Sheffieldstraat 35-39
2F, 111, Yeouigongwon-ro,
Yeongdeungpo-gu, Seoul, Korea
BLUE East Coast Operations (Sales Head Office)
91 Walsh Drive
The Netherlands (Sales Head Office)
Sheffieldstraat 35-39
2F, 111, Yeouigongwon-ro,
Yeongdeungpo-gu, Seoul, Korea
RED

Endless Linear Motion Type Limited Linear Motion Type

3047 AN Rotterdam Phone : +82 (0)2-6337-5851 Parsippany, NJ 07054 3047 AN Rotterdam Phone : +82 (0)2-6337-5851
The Netherlands Fax : +82 (0)2-6337-5852 U.S.A. The Netherlands Fax : +82 (0)2-6337-5852
Phone : +31 (0)10-462 68 68 E-mail : [email protected] Phone : +1 973-402-0254 Phone : +31 (0)10-462 68 68 E-mail : [email protected]
Fax : +31 (0)10-462 60 99 Toll Free : 1-800-922-0337 Fax : +31 (0)10-462 60 99
E-mail : [email protected] IKO-THOMPSON (SHANGHAI) LTD. (CHINA) Fax : +1 973-402-0441 E-mail : [email protected] IKO-THOMPSON (SHANGHAI) LTD. (CHINA)
Germany Branch E-mail : [email protected] Germany Branch
Mündelheimer Weg 54 Shanghai (Sales Head Office) Midwest Operations Mündelheimer Weg 54 Shanghai (Sales Head Office)
40472 Düsseldorf 1608-10 MetroPlaza No.555 LouShanGuan Road 101 Mark Street Suite-G, 40472 Düsseldorf 1608-10 MetroPlaza No.555 LouShanGuan Road
Germany ChangNing District Shanghai Wood Dale, IL 60191 Germany ChangNing District Shanghai
Phone : +49 (0)211-41 40 61 People's Republic of China 200051 U.S.A. Phone : +49 (0)211-41 40 61 People's Republic of China 200051
Fax : +49 (0)211-42 76 93 Phone : +86 (0)21-3250-5525 Phone : +1 630-766-6464 Fax : +49 (0)211-42 76 93 Phone : +86 (0)21-3250-5525
E-mail : [email protected] Fax : +86 (0)21-3250-5526 Toll Free : 1-800-323-6694 E-mail : [email protected] Fax : +86 (0)21-3250-5526
E-mail : [email protected] Fax : +1 630-766-6869 E-mail : [email protected]
Regensburg Sales Office Beijing Branch E-mail : [email protected] Regensburg Sales Office Beijing Branch
Im Gewerbepark D 30 Room1506, Jingtai Tower, Im Gewerbepark D 30 Room1506, Jingtai Tower,

●Shaft Guide Type

93059 Regensburg NO.24, Jianguomenwai Avenue, Minnesota Sales Office 93059 Regensburg NO.24, Jianguomenwai Avenue,
Germany Chaoyang District, Beijing People's Republic of 1500 McAndrews Road West, Suite 210 Germany Chaoyang District, Beijing People's Republic of
Phone : +49 (0)941-20 60 70 China 100022 Burnsville, MN 55337 Phone : +49 (0)941-20 60 70 China 100022
Fax : +49 (0)941-20 60 719 Phone : +86 (0)10-6515-7681 U.S.A. Fax : +49 (0)941-20 60 719 Phone : +86 (0)10-6515-7681
E-mail : [email protected] Fax : +86 (0)10-6515-7681 106 Phone : +1 952-892-8415 E-mail : [email protected] Fax : +86 (0)10-6515-7681 106
E-mail : [email protected] Toll Free : 1-800-323-6694 E-mail : [email protected]
Neunkirchen Sales Office Guangzhou Branch Fax : +1 952-892-1722 Neunkirchen Sales Office Guangzhou Branch
Gruben Str. 95c Room 834, Garden Tower, Garden Hotel E-mail : [email protected] Gruben Str. 95c Room 834, Garden Tower, Garden Hotel
66540 Neunkirchen 368 Huanshi East Road, Yuexiu District, Guangzhou, West Coast Operations 66540 Neunkirchen 368 Huanshi East Road, Yuexiu District, Guangzhou,

Endless Linear Motion Type

Germany Guangdong 9830 Norwalk Boulevard, Suite 198 Germany Guangdong
Phone : +49 (0)6821-99 98 60 People's Republic of China 510064 Santa Fe Springs, CA 90670 Phone : +49 (0)6821-99 98 60 People's Republic of China 510064
Fax : +49 (0)6821-99 98 626 Phone : +86 (0)20-8384-0797 U.S.A. Fax : +49 (0)6821-99 98 626 Phone : +86 (0)20-8384-0797
E-mail : [email protected] Fax : +86 (0)20-8381-2863 Phone : +1 562-941-1019 E-mail : [email protected] Fax : +86 (0)20-8381-2863
U.K. Branch E-mail : [email protected] Toll Free : 1-800-252-3665 U.K. Branch E-mail : [email protected]
2 Vincent Avenue, Crownhill Wuhan Branch Fax : +1 562-941-4027 2 Vincent Avenue, Crownhill Wuhan Branch
Milton Keynes, Bucks, MK8 0AB Room 2300, Truroll Plaza No.72 Wusheng Road, E-mail : [email protected] Milton Keynes, Bucks, MK8 0AB Room 2300, Truroll Plaza No.72 Wusheng Road,
United Kingdom Qiao kou District, Wuhan, Hubei United Kingdom Qiao kou District, Wuhan, Hubei

Limited Linear Motion Type

Phone : +44 (0)1908-566144 People's Republic of China 430033 Silicon Valley Sales Office Phone : +44 (0)1908-566144 People's Republic of China 430033
Fax : +44 (0)1908-565458 Phone : +86 (0)27-8556-1610 1500 Wyatt Drive, Suite 10 Fax : +44 (0)1908-565458 Phone : +86 (0)27-8556-1610
E-mail : [email protected] Fax : +86 (0)27-8556-1630 Santa Clara, CA 95054 E-mail : [email protected] Fax : +86 (0)27-8556-1630
Spain Branch E-mail : [email protected] U.S.A. Spain Branch E-mail : [email protected]
Autovia Madrid-Barcelona, Km. 43,700 Phone : +1 408-492-0240 Autovia Madrid-Barcelona, Km. 43,700
Polig. Ind. AIDA - Nove A-8, Ofic. 2-1a Shenzhen Office Toll Free : 1-800-252-3665 Polig. Ind. AIDA - Nove A-8, Ofic. 2-1a Shenzhen Office
19200 Azuqueca de Henares Room 420, Oriental Plaza, Fax : +1 408-492-0245 19200 Azuqueca de Henares Room 420, Oriental Plaza,
(Guadalajara) Spain 1072 Jianshe Road, Luohu District, E-mail : [email protected] (Guadalajara) Spain 1072 Jianshe Road, Luohu District,

Limited Linear Motion Type + Rolling Motion Type

Phone : +34 949-26 33 90 Shenzhen, Guangdong Southeast Operations Phone : +34 949-26 33 90 Shenzhen, Guangdong
Fax : +34 949-26 31 13 People's Republic of China 518001 2150 Boggs Road, Suite 100 Fax : +34 949-26 31 13 People's Republic of China 518001
E-mail : [email protected] Phone : +86 (0)755-2265-0553 Duluth, GA 30096 E-mail : [email protected] Phone : +86 (0)755-2265-0553
France Branch Fax : +86 (0)755-2298-0665 U.S.A. France Branch Fax : +86 (0)755-2298-0665
Roissypole Le Dôme E-mail : [email protected] Phone : +1 770-418-1904 Roissypole Le Dôme E-mail : [email protected]
2 rue de La Haye Ningbo Office Toll Free : 1-800-874-6445 2 rue de La Haye Ningbo Office
BP 15950 Tremblay en France Room 3406, Zhongnongxin Building, No.181 Fax : +1 770-418-9403 BP 15950 Tremblay en France Room 3406, Zhongnongxin Building, No.181
95733 Roissy C. D. G. Cedex Zhongshan East Road, Haishu Ward, Ningbo, E-mail : [email protected] 95733 Roissy C. D. G. Cedex Zhongshan East Road, Haishu Ward, Ningbo,
France Zhejiang Southwest Operations France Zhejiang
Phone : +33 (0)1-48 16 57 39 People's Republic of China 315000 8105 N. Beltline Road, Suite 130 Phone : +33 (0)1-48 16 57 39 People's Republic of China 315000
Fax : +33 (0)1-48 16 57 46 Phone : +86 (0)574-8718-9535 lrving, TX 75063 Fax : +33 (0)1-48 16 57 46 Phone : +86 (0)574-8718-9535
E-mail : [email protected] Fax : +86 (0)574-8718-9533 U.S.A. E-mail : [email protected] Fax : +86 (0)574-8718-9533
E-mail : [email protected] Phone : +1 972-929-1515 E-mail : [email protected]
IKO THOMPSON ASIA CO., LTD. (THAILAND) Qingdao Office Toll Free : 1-800-295-7886 IKO THOMPSON ASIA CO., LTD. (THAILAND) Qingdao Office
2107 Block A, World Trade Center Building, Fax : +1 972-915-0060 2107 Block A, World Trade Center Building,

●Flat Guide Type

1-7 Zuellig House, 3rd Floor No.230 E-mail : [email protected] 1-7 Zuellig House, 3rd Floor No.230
Silom Road, Silom, Bangrak Changjiang Middle Road, Development Zone Silom Road, Silom, Bangrak Changjiang Middle Road, Development Zone
Bangkok 10500, Thailand Qingdao IKO THOMPSON BEARINGS CANADA, INC.(CANADA) Bangkok 10500, Thailand Qingdao
Phone : +66 (0)2-637-5115 People's Republic of China 266555 Phone : +66 (0)2-637-5115 People's Republic of China 266555
FAX : +66 (0)2-637-5116 Phone : +86 (0)532-8670-2246 731-2425 Matheson Boulevard East 7th floor FAX : +66 (0)2-637-5116 Phone : +86 (0)532-8670-2246
E-mail : [email protected] FAX : +86 (0)532-8670-2242 Mississauga, Ontario L4W 5K4, Canada E-mail : [email protected] FAX : +86 (0)532-8670-2242
E-mail : [email protected] Phone : +1 905-361-2872 E-mail : [email protected]
Shenyang Office Fax : +1 905-361-6401 Shenyang Office
2-1203 Tower I.City Plaza Shenyang, No.206 E-mail : [email protected] 2-1203 Tower I.City Plaza Shenyang, No.206

Endless Linear Motion Type

Nanjing North Street Heping District, Shenyang Nanjing North Street Heping District, Shenyang
People's Republic of China 110001 People's Republic of China 110001
Phone : +86 (0)24-2334-2662 Phone : +86 (0)24-2334-2662
FAX : +86 (0)24-2334-2442 FAX : +86 (0)24-2334-2442
E-mail : [email protected] E-mail : [email protected]

Recognizing that conservation of the global environment is

notice. notice.

Limited Linear Motion Type

the top-priority challenge for the world’s population, Nippon
Thompson will conduct its activities with consideration of the
in case of falling under the customer's requirements, take necessary procedures such as export environment as a corporate social responsibility, reduce its in case of falling under the customer's requirements, take necessary procedures such as export
negative impact on the environment, and help foster a rich
permission application. global environment.
permission application.

possible, NIPPON THOMPSON CO., LTD. shall not be liable for any damages whatsoever, direct or possible, NIPPON THOMPSON CO., LTD. shall not be liable for any damages whatsoever, direct or
indirect, based upon any information in this catalog. NIPPON THOMPSON CO., LTD. makes no ISO 9001 & 14001 Quality system indirect, based upon any information in this catalog. NIPPON THOMPSON CO., LTD. makes no
warranty, either express or impiled, including the impiled warranty of merchantability or fitness for a registration certificate warranty, either express or impiled, including the impiled warranty of merchantability or fitness for a
particular purpose. particular purpose.

Printed in China © 2016.7 (AKA) Printed in China © 2016.7 (AKA)

CAT-1574E CAT-1575E

C-Lube Linear Way ML C-Lube Linear Way MLV C-Lube Linear Way MV C-Lube Linear Way ME C-Lube Linear Way MH Rail Guide Type Rail Guide Type Shaft Guide Type Shaft Guide Type
Linear Way L Linear Way E Linear Way H Crossed Roller Way Linear Slide Unit Linear Ball Spline Linear Bushing
ML・LWL MLV MV ME・LWE MH・LWH CRW(G)(…H) BWU･BSP(G) MAG･LSAG LMG・LM・LMS
CRWU(G) BSU…A LSB・LS

C-Lube
C-Lube Linear Way MUL Linear Roller Way Super MX Shaft Guide Type Flat Guide Type
Linear Way F Linear Way U Linear Roller Way Super X Linear Roller Way X Linear Way Module Stroke Rotary Bushing Roller Way & Flat Roller Cage
LWF MUL・LWU MX・LRX LRWX LWLM・LWM ST・STSI・BG RW・SR・GSN
LRWM FT･FTW…A M

M49 M50
 Features of Maintenance Free Series

Features
Features of
of C-Lube
C-Lube Linear
Linear Way
Way and
and C-Lube
C-Lube Linear
Linear Roller
Roller Way
Way Long term maintenance free is realized with
Gentle to The Earth
Original
Original and
and world's
world's first
first
oil impregnated with C-Lube only !!
structure with [C-Lube]
Maintenance free Durability test result
Linear Way No C-Lube
4.9 km lubrication shortage damage
C-Lube Linear Way C-Lube Linear Roller Way This endures running over 20,000 km without
LWL9 （No grease）

C-Lube Linear Way C-Lube integrated

High-speed at 240 m/min Running of 86,000 km without failure
oil feeding with lubrication oil in the C-Lube ML9 No grease
The aquamarine end plate is the only. C-Lube integrated
High acceleration / deceleration 26G Running of 46,000 km without failure

symbol of maintenance free. Furthermore, grease is pre-packed in the slide No grease

C-Lube integrated
unit so long term maintenance free can be Load of 0.09C Running of 89,000 km without failure
No grease
realized. C-Lube Linear Way C-Lube integrated
Load of 0.1C Running of 71,000 km without failure
ME25 No grease
Maintenance free is achieved C-Lube Linear Roller Way C-Lube integrated
Load of 0.1C
Running of 56,000 km without failure
*1 MXG45 No grease
until the end of device life ! 0 20 000km 40 000 60 000 80 000 100 000
*1. Typical device life is assumed. Re-greasing may
be necessary depending on use conditions. Traveling distance km

Eco-friendly Oil supply test result 100

No pre-packed grease
No applied load

Lubrication oil supply amount

ML9
80
ML12
As lubrication oil in C-Lube is supplied by the ML15
amount necessary to maintain lubrication perfor- 60

wt%
mance of the rolling guide, the consumption of 40
lubrication oil is reduced and lubrication perfor-
mance is maintained even when it run for a long 20

period.
0
Eco-friendly specification reducing 0 20 000km 40 000 60 000 80 000 100 000

Traveling distance km
usage of lubrication oil!

C-Lube integrated Compact External lubrication parts

Lubrication oil is carried through Lubrication oil is directly supplied As C-Lube Linear Way and C-Lube Linear Roller Linear way using
conventional lubrication parts
circulation of rolling elements to surfaces of the rolling elements Way are integrated with lubrication part C-Lube,
C-Lube Linear Way
their slide units are not long unlike types with
The lubrication oil is supplied directly to the rolling elements, The surface of capillary lubricating element is always covered
external lubrication parts.
not to the track rail. with the lubrication oil.
Replacement of conventional parts is easy free
When rolling elements make contact with the capillary lubri- Lubrication oil is continuously supplied to the surface of
cating element integrated with the circulation path of slide rolling elements by surface tension in the contact of capillary from constraints of mounting space and stroke
unit rolling elements, the lubrication oil is supplied to lubricating element surface and rolling elements. length.
surfaces of rolling elements and carried to the loading area On the surface of capillary lubricating element with which the
through circulation of rolling elements. rolling elements make contact, new lubrication oil is always Compact design taking into
This results in adequate lubrication oil being properly main- supplied from the other sections.
tained in the loading area and lubrication performance will account compactness!
last for a long time.
Cylindrical rollers Cylindrical rollers

C-Lube Smooth Frictional resistance

test result
3.0 ML9 standard preload

Cylindrical rollers Lubrication

Frictional resistance N
oil film
Surface C-Lube Linear Way and C-Lube Linear Roller
tension 2.0
Way do not generate slide resistance unlike lubri-
cation parts external to the slide unit that make
contact with the track rail. 1.0
Capillary
C-Lube C-Lube Driving force follow-up property is superior and
ction
ke dire energy is saved by improvement of accuracy and
Track
rail nit stro
Slide u 0
reduction of friction loss. 0 50 100 150
Traveling distance mm
Light and smooth motion is achieved!
M51 M52
Models and Size Variations

A variety of models and size variations

Ball Type Miniature Series Ball Type Compact Series
C-Lube Linear Way ML C-Lube Linear Way ME
C-Lube Linear Way MLV Linear Way E
Linear Way L Low Decibel Linear Way E
Versatile linear motion rolling guide that has achieved utility pursuing com-
Thanks to the structure with two rows of balls to contact with the way at
pactness in every aspect. Low decibel types with resin separator to prevent
four points, stable accuracy and rigidity can be achieved even in applica-
direct contact between balls are also available.
tions where load has variable direction and size or complex load is applied,
despite its very small body.

Flange type Flange type Block type

Length of slide unit Size
mounting from bottom mounting from top mounting from top
Micro Linear Way L ME MET MES
C
Short 15, 20, 25, 30, 35, 45

LWE LWET LWES Standard

As the lineup of track rail width from 1 mm to 6 mm is available, you can select an optimal No
symbol
product for the specifications of your machine and device. For LWL1, world's smallest
size is realized: track rail width of 1 mm, slide unit width of 4 mm and assembly height of Long
G
2.5 mm.

Standard type Wide type Length of slide unit Size

ML MLF Short Standard 1, 2, 3, 5, 7, 9, 12, 15, 20, 25
C type
LWL LWLF
Wide type 4, 6, 10, 14, 18, 24, 30, 42
Ball Type High Rigidity Series
Standard
No
symbol
Long
C-Lube Linear Way MH
G
Linear Way H
Extra long
L
High rigidity linear motion rolling guides designed to evenly support high
load capacity by incorporating large-diameter balls. Stable accuracy and
rigidity can be achieved even in applications where load with variable direc-
Ball Type Low Profile/Light Weight Series tion and size and complex load are applied.

C-Lube Linear Way MV

Flange type Flange type Block type Compact block type Length of slide unit
mounting from bottom mounting from top（1） mounting from top mounting from top Short
Despite its extra low profile and extra light weight, this linear motion rolling
MH MHT MHD MHS C
guide has the maximum load rating among the ball types while achieving
LWH LWHT LWHD LWHS
high load capacity. Standard
No
symbol

M
Long
G

Extra long
L
Size
Length of slide unit Size
Standard 20, 25, 30 Note（1）Some models may be mounted from bottom. Size
8, 10, 12, 15, 20, 25, 30, 35, 45, 55, 65

M53 M54
Models and Size Variations

A variety of models and size variations

Ball Type Wide Type Series Roller Type

Linear Way F C-Lube Linear Roller Way Super MX
Linear Roller Way Super X
As wide track rail is used and the distance between the load points is long,
this is a linear motion rolling guide suitable to single-row use due to the
structure resistant to across-the-width moment load. It is also resistant to Linear motion rolling guide that has achieved the highest level of perfor-
complex load. mance in all characteristics utilizing the roller's superior characteristic, such
as rigidity, load capacity, running accuracy and vibration damping property.
With extra long unit with the maximum slide unit length, load capacity and
rigidity are improved and running performance with super high accuracy is
realized.

Flange type Block type Compact block type Low profile flange type Low profile block type
Flange type Flange type Block type Length of slide unit mounting from top / bottom mounting from top mounting from top mounting from top mounting from top
mounting from top / bottom mounting from top / bottom mounting from top No Standard
MX（1） MXD MXS MXN MXNS
LWFH LWFF LWFS symbol LRX（1） LRXD LRXS

Size
LWFH 40,60,90
LWFF 33,37,42,69
LWFS 33,37,42 Note（1） Size 20 series allows only for mounting from top and model mounting from bottom is MXH and LRXH.

Length of slide unit Size

C No symbol G L 10, 12, 15, 20, 25, 30, 35, 45, 55, 65, 85, 100
Short Standard Long Extra long

Ball Type U-Shaped Track Rail Series

C-Lube Linear Way MUL
Linear Way U Four-row roller guide of world's smallest size
Linear motion rolling guide of the structure with way inside the track rail of
Track rail width of 10 mm
U-shaped section and slide unit therein. With the U-shaped track rail, rigid-
ity against the track rail moment load and torsion is significantly improved.

Small type Standard type Length of slide unit

MUL LWU No Standard
LWUL symbol Super high rigidity

MUL 25, 30
Size Super high load capacity
Stainless steel made
M
High running performance
LRXD10…SL
LWUL 25, 30
LWU 40, 50, 60, 86, 100, 130 Excellent frictional characteristics

M55 M56
 Presentation of Mechatronics Series
Mechatronics Series

TU Series
Precision Positioning Ta-
ble TU is a compact and slim po-
sitioning table with good load bal-
ance and high resistance to com-
plex loads, in which the side table
is arranged inside the U-shape
track rail. Six types with a track
rail width of 25 ∼ 130mm are
available. Each slide table length
can be selected as required. Dif-
ferent table specifications includ- Precision Positioning Table
ing ball screw, motor, sensor, etc. can be selected. This allows each user to configure the
● Light weight precision positioning table
most suitable positioning table for each application.
made of high-strength aluminum alloy.
Abundant options meet diversified market needs such as a motor loopback specification, table ● Built-in C-Lube for long-term maintenance-
with bellows, table with bridge cover, and table finished by black chrome surface treatment. free service.

Linear Motor Table LT

The Linear Motor Table LT is TE B
a compact and lightweight direct-
drive positioning table with a very Micro Precision Positioning Table
small sectional height in which an AC
servo-motor and an optional linear ● Very compact positioning table that
is 20mm high（sectional）and 17mm
scale are integrated in a moving table
wide driven by a ground ball screw.
and a bed made of aluminum alloy.
● +/-0.5micron repeatability is achieved
The Linear Motor Table LT with 60 mm stroke length.
employs a C-shaped magnet yoke,
and a coil board is sandwiched be-
tween two stator magnets. It pro-
vides a high thrust of 450N though its height is only 40 mm. The moving table is as light as 1.5 kg but
provides high thrust. It permits high acceleration and deceleration exceeding 10 G. (In the case of
LT150 CG.) Also, High Thrust Series LT…H outputs 900N thrust.
M
TM
Using advanced servo technology, this product achieves high static stability and high-speed stability.

M57 M58
 Introduction of Technical Service Site 1. Technical calculations
For Linear Way/Linear Roller Way load and life calculation, you
can obtain the calculated load and the rating life by entering the
" Technical Service Site" can be accessed from our home page . The site also distributes
operating conditions.
various tools, etc., to select Linear ways/Linear roller ways, and please utilize the site for the assis- Also you can derive the motor torque required for operation and
tance to select products. Additionally the site also provides CAD data and product catalog of needle the effective propulsion force during operation in the sections of
series, linear motion rolling guide series and mechatronics series for you to download. Please motor torque calculation and calculation of effective propulsion
force of linear motor tables respectively, and output the calcula-
consider to use for enhancing your design efficiency.
tion results in PDF format, as well as save the histories.

2. Selection of Identification Number

By selecting such specification as model code, dimensions, part code, material
code, preload symbol, classification symbol, interchangeable code and
supplemental code of Linear ways/Linear roller ways, you can easily specify
the identification number used for ordering.
Also you can browse the CAD data of the selected products, calculate the load,
and output the selection results in PDF format, as well as save the histories.

3. Downloading CAD data

2-dimensional CAD data (DXF file) 3-dimensional CAD data
There are two types of figures, brief figure and detailed figure. The It is linked to the mechanical parts CAD library
brief figure shows only the external view lines, and the detailed "PART community". Entering the rail dimension
figure shows the detailed lines. The drawing consists of three and option contents to the detail, you can view
drawings: front view, side view and plain view. The scale shows the 2D/3D CAD data suitable for the specification
only the original size (1:1), and it does not show dimension lines. for free of charge.

4. Downloading Catalog and Operation Manual

You can download product catalogs of needle series, linear motion rolling guide series and mechatronics M
series, operation manuals of precision positioning tables and various electrical components in PDF format,
as well as support software for precision positioning tables. If you would like a copy of our catalog, please
visit the official website and apply for the catalog, or contact our regional office or sales office nearby.

M59 M60
 A CF…FWBUUR I41 Cam Followers CFKR…UU I29 Double Hex Hole Cam Followers CRBS…AUU J23 Crossed Roller Bearings

AR L21 Cir-clips for Needle Roller Bearings CF…G I47 Cam Followers CFKR…UUR I29 Double Hex Hole Cam Followers CRBS…V J23 Crossed Roller Bearings

AS F7 Thrust Bearings CF…VB I25 Cam Followers CFS I51 Miniature Type Cam Followers CRBS…VUU J23 Crossed Roller Bearings

AZ F11 Thrust Bearings CF…VBM I25 Cam Followers CFS…F I53 Miniature Type Cam Followers CRBT…A J21 Crossed Roller Bearings

AZK F11 Thrust Bearings CF…VBR I25 Cam Followers CFS…FW I57 Miniature Type Cam Followers CRH…V I75 Cam Followers

CF…VBRM I25 Cam Followers CFS…FV I53 Miniature Type Cam Followers CRH…VR I73 Cam Followers

CF…VBUU I25 Cam Followers CFS…V I51 Miniature Type Cam Followers CRH…VB I71 Cam Followers

B CF…VBUUM I25 Cam Followers CFS…W I55 Miniature Type Cam Followers CRH…VBR I69 Cam Followers

BA…Z B27 Shell Type Needle Roller Bearings CF…VBUUR I25 Cam Followers CFS…WV I55 Miniature Type Cam Followers CRH…VBUU I71 Cam Followers

BAM B27 Shell Type Needle Roller Bearings CF…VBUURM I25 Cam Followers CL I22 C-Lube Unit for Cam Followers CRH…VBUUR I69 Cam Followers

BAMW B45 Shell Type Needle Roller Bearings CF…WBR I39 Cam Followers CR I63 Cam Followers CRH…VUU I75 Cam Followers

BAW…Z B45 Shell Type Needle Roller Bearings CF…WBUUR I39 Cam Followers CR…B I61 Cam Followers CRH…VUUR I73 Cam Followers

BHA…Z B27 Shell Type Needle Roller Bearings CF…WBUUR/SG I49 C-Lube Cam Followers CR…BR I61 Cam Followers CRY…V I101 Roller Followers

BHAM B27 Shell Type Needle Roller Bearings CF−FU1 I43 Cam Followers CR…BUU I61 Cam Followers CRY…VR I99 Roller Followers

BR D47 Machined Type Needle Roller Bearings CF−RU1 I43 Cam Followers CR…BUUR I61 Cam Followers CRY…VUUR I99 Roller Followers

BR…UU D67 Machined Type Needle Roller Bearings CF−SFU…B I45 Cam Followers CR…R I63 Cam Followers CRY…VUU I101 Roller Followers

BRI D51 Machined Type Needle Roller Bearings CFE…B I35 Cam Followers CR…UU I63 Cam Followers

BRI…UU D71 Machined Type Needle Roller Bearings CFE…BR I35 Cam Followers CR…UUR I63 Cam Followers

CFE…BUU I35 Cam Followers CR…V I67 Cam Followers D

CFE…BUUR I35 Cam Followers CR…VB I65 Cam Followers DS L4 Seals for Needle Roller Bearings

C CFE…VB I37 Cam Followers CR…VBR I65 Cam Followers

CF…B I23 Cam Followers CFE…VBR I37 Cam Followers CR…VBUU I65 Cam Followers

CF…BM I23 Cam Followers CFE…VBUU I37 Cam Followers CR…VBUUR I65 Cam Followers G
CF…BR I23 Cam Followers CFE…VBUUR I37 Cam Followers CR…VR I67 Cam Followers GE…E K15 Spherical Bushings

CF…BRM I23 Cam Followers CFES…B I33 Cam Followers CR…VUU I67 Cam Followers GE…EC K27 Spherical Bushings

CF…BUU I23 Cam Followers CFES…BR I33 Cam Followers CR…VUUR I67 Cam Followers GE…EC−2RS K27 Spherical Bushings

CF…BUUM I23 Cam Followers CFES…BUU I33 Cam Followers CRB J17 Crossed Roller Bearings GE…ES K15 Spherical Bushings

CF…BUUR I23 Cam Followers CFES…BUUR I33 Cam Followers CRB…UU J17 Crossed Roller Bearings GE…ES−2RS K15 Spherical Bushings

CF…BUURM I23 Cam Followers CFKR I29 Double Hex Hole Cam Followers CRBC J17 Crossed Roller Bearings GE…G K19 Spherical Bushings

CF…FB I27 Cam Followers CFKR…R I29 Double Hex Hole Cam Followers CRBC…UU J17 Crossed Roller Bearings GE…GS K19 Spherical Bushings

CF…FBR I27 Cam Followers CFKR…V I31 Double Hex Hole Cam Followers CRBF(V) J25 Crossed Roller Bearings GE…GS−2RS K19 Spherical Bushings M
CF…FBUU I27 Cam Followers CFKR…VR I31 Double Hex Hole Cam Followers CRBH(V)…A J15 Crossed Roller Bearings GS F7 Thrust Bearings

CF…FBUUR I27 Cam Followers CFKR…VUU I31 Double Hex Hole Cam Followers CRBH(V)…AUU J15 Crossed Roller Bearings GTR D9 Machined Type Needle Roller Bearings

CF…FWBR I41 Cam Followers CFKR…VUUR I31 Double Hex Hole Cam Followers CRBS J23 Crossed Roller Bearings GTRI D31 Machined Type Needle Roller Bearings

M61 M62
 I NART…UUR/SG I95 C-Lube Roller Followers P T
IRB H10 Inner Rings NART…VR I89 Roller Followers PB K37 PILLOBALLs TA…Z B7 Shell Type Needle Roller Bearings

IRT H5 Inner Rings NART…VUUR I89 Roller Followers PHS K38 PILLOBALLs TAF D7 Machined Type Needle Roller Bearings

K NAS 50…UUNR E19 Roller Bearings PHS…EC K43 PILLOBALLs TAF…/SG D77 C-Lube Machined Type Needle Roller Bearings

KT C5 Needle Roller Cages for General Usage NAS 50…ZZNR E19 Roller Bearings PHSA K42 PILLOBALLs TAFI D29 Machined Type Needle Roller Bearings

KT…EG C21 Needle Roller Cages for Engine Connecting Rods NAST I86 Roller Followers PHSB K40 PILLOBALLs TAM B7 Shell Type Needle Roller Bearings

KTV…EG C22 Needle Roller Cages for Engine Connecting Rods NAST…R I86 Roller Followers POS K39 PILLOBALLs TAMW B21 Shell Type Needle Roller Bearings

KTW C9 Needle Roller Cages for General Usage NAST…ZZ I87 Roller Followers POSB K41 PILLOBALLs TAW…Z B21 Shell Type Needle Roller Bearings

NAST…ZZR I87 Roller Followers POS…EC K44 PILLOBALLs TLA…UU B49 Shell Type Needle Roller Bearings

NAST…ZZUU I87 Roller Followers PRC K53 PILLOBALLs TLA…Z B7 Shell Type Needle Roller Bearings

L NAST…ZZUUR I87 Roller Followers TLAM B7 Shell Type Needle Roller Bearings

LHS K51 L-Balls NATA 59 G9 Combined Type Needle Roller Bearings TLAMW B17 Shell Type Needle Roller Bearings

LHSA K49 L-Balls NATB 59 G9 Combined Type Needle Roller Bearings R TLAW…Z B17 Shell Type Needle Roller Bearings

LRB H25 Inner Rings NAU 49 E7 Roller Bearings RNA 48 D23 Machined Type Needle Roller Bearings TR D9 Machined Type Needle Roller Bearings

LRBZ H25 Inner Rings NAU 49…UU E13 Roller Bearings RNA 49 D7 Machined Type Needle Roller Bearings TRI D31 Machined Type Needle Roller Bearings

LRBZ…B H25 Inner Rings NAX G5 Combined Type Needle Roller Bearings RNA 49…UU D55 Machined Type Needle Roller Bearings TRU E7 Roller Bearings

LRT H13 Inner Rings NAX…Z G5 Combined Type Needle Roller Bearings RNA 69 D9 Machined Type Needle Roller Bearings TRU…UU E13 Roller Bearings

LRTZ H13 Inner Rings NAXI G7 Combined Type Needle Roller Bearings RNA 69…UU D55 Machined Type Needle Roller Bearings

NAXI…Z G7 Combined Type Needle Roller Bearings RNAF D83 Needle Roller Bearings with Separable Cage

NBX G5 Combined Type Needle Roller Bearings RNAFW D83 Needle Roller Bearings with Separable Cage W
N NBX…Z G5 Combined Type Needle Roller Bearings RNAST I85 Roller Followers WR L19 Cir-clips for Needle Roller Bearings

NA 48 D41 Machined Type Needle Roller Bearings NBXI G7 Combined Type Needle Roller Bearings RNAST…R I85 Roller Followers WS F7 Thrust Bearings

NA 49 D29 Machined Type Needle Roller Bearings NBXI…Z G7 Combined Type Needle Roller Bearings

NA 49…UU D61 Machined Type Needle Roller Bearings NTB F7 Thrust Needle bearings

NA 69 D29 Machined Type Needle Roller Bearings NUCF…BR I59 Cam Followers S Y
NA 69…UU D61 Machined Type Needle Roller Bearings NURT I97 Roller Followers SB K11 Spherical Bushings YB B27 Shell Type Needle Roller Bearings

NAF D89 Needle Roller Bearings with Separable Cage NURT…R I97 Roller Followers SB…A K11 Spherical Bushings YBH B29 Shell Type Needle Roller Bearings

NAFW D89 Needle Roller Bearings with Separable Cage SBB K23 Spherical Bushings YT B7 Shell Type Needle Roller Bearings

NAG 49 E7 Roller Bearings SBB…−2RS K23 Spherical Bushings YTL B7 Shell Type Needle Roller Bearings

NAG 49…UU E13 Roller Bearings O SNA K58 Super Flexible Nozzle

NART…FR I93 Roller Followers OS L3 Seals for Needle Roller Bearings SNM K59 Super Flexible Nozzle M
NART…FUUR I93 Roller Followers SNPT K59 Super Flexible Nozzle

NART…R I89 Roller Followers

NART…UUR I89 Roller Followers

M63 M64
 Products Underpin Sustain
Technology Leaps
Nippon Thompson Co., Ltd. was the first Japanese manufacturer to develop
needle bearings on its own and has since expanded into the arena of linear
motion rolling guides (Linear Motion Series and Mechatro Series) on the
support of its advanced expertise. The company now offers a vast assortment

Gentle to The Earth

of ingenious products, including the world’s first C-Lube maintenance-free
series, to address increasingly diversified customer needs and thus sustain
technology leaps.

C-Lube Maintenance-Free Series Products

Nippon Thompson Co., Ltd. is working to develop global environment-friendly products. Evolving from the “Oil Minimum” Concept
It is committed to developing products that make its customers’ machinery and
We have developed lubricating parts impregnated with a large amount of
equipment more reliable, thereby contributing to preserving the global environment. lubricant as C-Lube Series to save the customer’s oiling management workload
and built them into bearings and linear motion rolling guides.
This development stance manifests well in the keyword “Oil Minimum.”
The C-Lube Series not only keeps products maintenance-free for long by giving
Our pursuit of Oil Minimum has led to the creation of them an optimal and minimal amount of a lubricant for an extended period of
time but also contributes greatly to preserving the global environment.
’s proprietary family of lubricating parts as “C-Lube.”

Needle Bearings
Machine elements essential to any industry

Linear Motion Rolling Guides/Linear Motion Series

Available in broad sizes, from minimum to extra-large

● Linear Motion Rolling Guides are manufactured through a control

system that alleviates their impact on the global environment to meet the
M
quality requirements of ISO 14001 and ISO 9001.
● The standard products listed in this catalog comply with the specifications of

the six hazardous materials mentioned cited in the European RoHS Directive. Linear Motion Rolling Guides/Mechatro Series
A merger of precision machining expertise and electronics
For information on all other products, please check with .
M65 M66
● Although all data in this catalog has been carefully compiled to make the information as complete as possible, NIPPON THOMPSON CO., LTD. shall not be liable for
any damage whatsoever, direct or indirect, based on on any of the information contained in this catalog.
NIPPON THOMPSON CO., LTD. makes no warranty, either express or implied, including the implied warranty of merchantability or fitness for a particular purpose.

NIPPON THOMPSON CO., LTD.

CAT-1577E  C All rights reserved AKA
Printed in China 2018.7

M67
 New Jersey, U.S.A Düsseldorf, Germany

Illinois, U.S.A United Kingdom

Main entrance of Gifu plant

California, U.S.A Spain

Georgia, U.S.A France

Texas, U.S.A Toronto, Canada

Show room “ TODAY” The Netherlands São Paulo, Brazil

SERVICE NETWORK OF PRODUCTS

NIPPON THOMPSON CO., LTD. (JAPAN) IKO-THOMPSON (SHANGHAI) LTD. (CHINA) IKO INTERNATIONAL, INC. (U.S.A.) NIPPON THOMPSON EUROPE B.V. (EUROPE)
Head Office : 7-17 Shiba 2-chome Minato-ku Shanghai (Sales Head Office) East Coast Operations (Sales Head Office) The Netherlands (Sales Head Office)
Tokyo 105-0014, Japan 1608-10 MetroPlaza No.555 LouShanGuan Road 91 Walsh Drive Sheffieldstraat 35
Phone : +81 (0)3-3448-5850 ChangNing District Shanghai Parsippany, NJ 07054 3047 AN Rotterdam
Fax : +81 (0)3-3447-7637 People’s Republic of China 200051 U.S.A. The Netherlands
E-mail : [email protected] Phone : +86 (0)21-3250-5525 Phone : +1 973-402-0254 Phone : +31 (0)10-462 68 68
URL : http://www.ikont.co.jp/eg/ Fax : +86 (0)21-3250-5526 Toll Free : 1-800-922-0337 Fax : +31 (0)10-462 60 99
Plant : Gifu, Kamakura E-mail : [email protected] Fax : +1 973-402-0441 E-mail : [email protected]
Beijing Branch E-mail : [email protected] Germany Branch
IKO THOMPSON KOREA CO.,LTD. (KOREA) Room1506, Jingtai Tower, Midwest Operations Mündelheimer Weg 54
NO.24, Jianguomenwai Avenue, 101 Mark Street Unit G, 40472 Düsseldorf
2F, 111, Yeouigongwon-ro, Chaoyang District, Beijing People's Republic of China 100022 Wood Dale, IL 60191 Germany
Yeongdeungpo-gu, Seoul, Korea Phone : +86 (0)10-6515-7681 U.S.A. Phone : +49 (0)211-41 40 61
Phone : +82 (0)2-6337-5851 Fax : +86 (0)10-6515-7681*106 Phone : +1 630-766-6464 Fax : +49 (0)211-42 76 93
Fax : +82 (0)2-6337-5852 E-mail : [email protected] Toll Free : 1-800-323-6694 E-mail : [email protected]
E-mail : [email protected] Guangzhou Branch Fax : +1 630-766-6869
Room 834, Garden Tower, Garden Hotel E-mail : [email protected] Regensburg Sales Office
IKO THOMPSON ASIA CO., LTD. (THAILAND) 368 Huanshi East Road, Yuexiu District, Guangzhou, Guangdong Im Gewerbepark D 30
People’s Republic of China 510064 Minnesota Sales Office 93059 Regensburg
1-7 Zuellig House, 3rd Floor Phone : +86 (0)20-8384-0797 1500 McAndrews Road West, Suite 210 Germany
Silom Road, Silom, Bangrak Fax : +86 (0)20-8381-2863 Burnsville, MN 55337 Phone : +49 (0)941-20 60 70
Bangkok 10500, Thailand E-mail : [email protected] U.S.A. Fax : +49 (0)941-20 60 719
Phone : +66 (0)2-637-5115 Wuhan Branch Phone : +1 952-892-8415 E-mail : [email protected]
FAX : +66 (0)2-637-5116 Room 2300, Truroll Plaza No.72 Wusheng Road, Toll Free : 1-800-323-6694
E-mail : [email protected] Fax : +1 952-892-1722 Neunkirchen Sales Office
Qiao kou District, Wuhan, Hubei
E-mail : [email protected] Gruben Str.95c
People’s Republic of China 430033
West Coast Operations 66540 Neunkirchen
Phone : +86 (0)27-8556-1610
9830 Norwalk Boulevard, Suite 198 Germany
Fax : +86 (0)27-8556-1630
Santa Fe Springs, CA 90670 Phone : +49 (0)6821-99 98 60
E-mail : [email protected]
U.S.A. Fax : +49 (0)6821-99 98 626
Shenzhen Office Phone : +1 562-941-1019 E-mail : [email protected]
Room 420, Oriental Plaza, Toll Free : 1-800-252-3665 U.K. Branch
1072 Jianshe Road, Luohu District, Shenzhen, Guangdong Fax : +1 562-941-4027 2 Vincent Avenue, Crownhill
People’s Republic of China 518001 E-mail : [email protected] Milton Keynes, Bucks, MK8 0AB
Phone : +86 (0)755-2265-0553 United Kingdom
Fax : +86 (0)755-2298-0665 Silicon Valley Sales Office Phone : +44 (0)1908-566144
E-mail : [email protected] 1500 Wyatt Drive, Suite 10 Fax : +44 (0)1908-565458
Ningbo Office Santa Clara, CA 95054 E-mail : [email protected]
Room 3406, Zhongnongxin Building, No.181 U.S.A. Spain Branch
Zhongshan East Road, Haishu Ward, Ningbo, Zhejiang Phone : +1 408-492-0240 Autovia Madrid-Barcelona, Km. 43,700
People’s Republic of China 315000 Toll Free : 1-800-252-3665 Polig. Ind. AIDA - Nove A-8, Ofic. 2-1
Phone : +86 (0)574-8718-9535 Fax : +1 408-492-0245 19200 Azuqueca de Henares
Recognizing that conservation of the global environment is Fax : +86 (0)574-8718-9533 E-mail : [email protected] (Guadalajara) Spain
the top-priority challenge for the world’s population, Nippon E-mail : [email protected] Southeast Operations Phone : +34 949-26 33 90
Thompson will conduct its activities with consideration of the Qingdao Office 2150 Boggs Road, Suite 100 Fax : +34 949-26 31 13
environment as a corporate social responsibility, reduce its
2107 Block A, World Trade Center Building, No.230 Duluth, GA 30096 E-mail : [email protected]
negative impact on the environment, and help foster a rich
Changjiang Middle Road, Development Zone Qingdao U.S.A. France Branch
global environment.
People’s Republic of China 266555 Phone : +1 770-418-1904 Roissypole Le Dôme
Phone : +86 (0)532-8670-2246 Toll Free : 1-800-874-6445 2 rue de La Haye
ISO 9001 & 14001 Quality system FAX : +86 (0)532-8670-2242 Fax : +1 770-418-9403 BP 15950 Tremblay en France
E-mail : [email protected] 95733 Roissy C. D. G. Cedex
registration certificate E-mail : [email protected]
Southwest Operations
Shenyang Office France
2-1203 Tower I.City Plaza Shenyang, No.206 8105 N. Beltline Road, Suite 130 Phone : +33 (0)1-48 16 57 39
Nanjing North Street Heping District, Shenyang lrving, TX 75063 Fax : +33 (0)1-48 16 57 46
People’s Republic of China 110001 U.S.A. E-mail : [email protected]
Phone : +86 (0)24-2334-2662 Phone : +1 972-929-1515
FAX : +86 (0)24-2334-2442 Toll Free : 1-800-295-7886
E-mail : [email protected] Fax : +1 972-915-0060
E-mail : [email protected]
• The specifications and dimensions of products in this catalog are subject to
change without prior notice.
• When these products are exported, the exporter should confirm a
IKO THOMPSON BEARINGS CANADA, INC. (CANADA) IKO THOMPSON BRAZIL SERVICE CO.,LTD. (BRAZIL)
forwarding country and a use, and, in case of falling under the customer's
requirements, take necessary procedures such as export permission
731-2425 Matheson Boulevard East 7th floor Av.Paulista, 854 10th floor, Top Center,
application.
Mississauga, Ontario L4W 5K4, Canada 01310-100, Sao Paulo, SP, Brazil
Phone : +1 905-361-2872 Phone : +55-(0)11-2186-0221
• Although all data in this catalog has been carefully compiled to make the
Fax : +1 905-361-6401 FAX : +55-(0)11-2186-0299
information as complete as possible, NIPPON THOMPSON CO., LTD. shall
E-mail : [email protected] E-mail : [email protected]
not be liable for any damages whatsoever, direct or indirect, based upon any
information in this catalog. NIPPON THOMPSON CO., LTD. makes no
warranty, either express or impiled, including the impiled warranty of
merchantability or fitness for a particular purpose.
• Reproduction and conversion without permission are prohibited.