SANDVIK PERFORMANCE FLUIDS
LONG-LIFE HYDRAULIC OIL
SANDVIK OH32-OH150
TECHNICAL SPECIFICATION
DESCRIPTION
Proper function and operating safety of hydraulic
systems are largely influenced by the quality of the
hydraulic medium. In addition to the task of transferring
forces, the operating fluid must seal, cool and lubricate.
Since hydraulic oils are exposed to high stress due
to the operating conditions, they have to fulfil a large
number of requirements. The oils of the Sandvik OH
series are formulated on the basis of highly ageing-
resistant solvates containing additives that increase
the aging resistance. The products of the Sandvik OH
series are zinc-containing HVLP hydraulic and general
lubricating oils according to DIN 51524-3. Mineral oil-
based, demulsifying.
KEY FEATURES
Low foaming tendency
APPLICATION
Sandvik OH high-quality products are used as Good air release properties
hydraulic oil and as lubricating oil for various
High ageing resistance
applications like bearings and gear boxes, even when
a high viscosity index and good load carrying capacity Good corrosion protection
is required. Especially recommended for applications
Very good viscosity-temperature-behaviour
where a low start-up viscosity at low temperatures and
a higher viscosity at higher temperatures is required. Very good wear protection
Particularly suited to all applications in mobile hydraulic High viscosity index
systems that require the use of an HVLP oil according
Wide service temperature range
to DIN 51524-3 with a wide service temperature range.
Good shear stability
SPECIFICATIONS
The products meet or exceed the requirements according to
DIN 51524-3, HVLP
ISO 6743-4, HV
ISO 11158
TYPICAL CHARACTERISTICS
Product name OH32 OH46 OH68
Properties Unit Test method
ISO VG 32 46 68 DIN 51519
Kinematic viscosity DIN EN ISO 3104
at – 20 °C mm2/s 1858 3486 -
at 0 °C mm2/s 233.4 401.6 618.9
at 40 °C mm2/s 32 46 68
at 100 °C mm2/s 6.3 8.1 11.0
Viscosity index - 152 150 153 DIN ISO 2909
Density at 15 °C kg/m³ 871 879 868 DIN 51757
Flashpoint (COC) °C 178 186 240 DIN ISO 2592
Pourpoint °C -48 -45 -36 DIN ISO 3016
Neutralisation number mgKOH/g 0.5 0.5 0.5 DIN 51558-2
FZG mechanical gear test rig failure load
11 11 11 DIN ISO 14635-1
FZG A/8.3/90 stage
Product name OH100 OH150
Properties Unit Test method
ISO VG 100 150 DIN 51519
Kinematic viscosity DIN EN ISO 3104
at – 20 °C mm2/s - -
at 0 °C mm2/s - -
at 40 °C mm2/s 100 150
at 100 °C mm2/s 13.5 17.7
Viscosity index - 140 130 DIN ISO 2909
Density at 15 °C kg/m³ 871 881 DIN 51757
Flashpoint (COC) °C 240 260 DIN ISO 2592
Pourpoint °C -24 -24 DIN ISO 3016
Neutralisation number mgKOH/g 0.5 0.5 DIN 51558-2
FZG mechanical gear test rig failure load
11 11 DIN ISO 14635-1
FZG A/8.3/90 stage
2 SANDVIK OH32-OH150
VICKERS V104C PUMP TEST
Maximum
Sandvik OH68 shows up to 80 % less wear
than the maximum allowed in industry-stan-
dard hydraulic pump test.
Sandvik
TS15-127-132:01/ENG/METRIC © Sandvik Mining 2017 SANDVIK is a registered trademark owned by Sandvik Intellectual Property AB in Sweden and other countries.
OXIDATION STABILITY / LIFETIME TEST
Minimum
Sandvik OH68 reaches up to 300% of the mini-
mum lifetime compared to Standard hydraulic
fluids.
Sandvik
* Always refer to the installation manuals
Sandvik Mining reserves the right to make changes to the information on this data sheet without prior notification to users.
Please contact a Sandvik representative for clarification on specifications and options.
MINING.SANDVIK.COM
