Service Manual

ViewSonic VX2250W-LED-1
VX2250WM-LED-1
Model No. VS13239
22” Color TFT LCD Display

(VX2250W-LED-1_VX2250WM-LED-1_SM Rev. 1a May. 2010)

ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
 Copyright
Copyright © 2010 by ViewSonic Corporation. All rights reserved. No part of
this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of ViewSonic Corporation.

Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranty of
merchantability or fitness for any particular purpose. Further, ViewSonic
reserves the right to revise this publication and to make changes from time to
time in the contents hereof without obligation of ViewSonic to notify any person
of such revision or changes.

Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their
respective owners.

Product disposal at end of product life

The lamp in this product contains mercury. Please dispose of in accordance with
local, state or federal laws.

Revision History
Revision SM Editing Date ECR Number Description of Changes Editor

1a 05/11/2010 Initial Release Hilda Huang

VX2250W-1
ViewSonic Corporation I CONFIDENTIAL – DO NOT COPY VX2250WM-1
 TABLE OF CONTENTS

1. Precautions and Safety Notices ........................................................................................1

2. Specification ......................................................................................................................4

3. Front Panel Function Control Description ..................................................................... 20

4. Circuit Description............................................................................................................. 37

5. Adjusting Procedure........................................................................................................ 4 1

6. Trouble Shooting Flow Chart ............................................................................................ 69

7. Block Diagrams ................................................................................................................ 75

8. Schematic Diagrams ........................................................................................................ 76

9. PCB Layout Diagrams ..................................................................................................... 86

10. Exploded Diagram And Spare Parts List...................................................................... .90

11. Recommended Spare Parts List .................................................................................. .98

VX2250W-1
ViewSonic Corporation II CONFIDENTIAL – DO NOT COPY VX2250WM-1
 1. Precautions and Safety Notices

1. SAFETY PRECAUTIONS
This monitor is manufactured and tested on a ground principle that a user’s safety comes
first. However, improper used or installation may cause damage to the monitor as well as
to the user.
WARNINGS:
This monitor should be operated only at the correct power sources indicated on the
label on the rear of the monitor. If you’re unsure of the power supply in you residence,
consult your local dealer or Power Company.
Use only the special power adapter that comes with this monitor for power input.
Do not try to repair the monitor by yourself, as it contains no user-serviceable parts.
Only the qualified technician can repair it.
Do not remove the monitor cabinet. There are high-voltage parts inside that may
cause electric shock to human bodies.
Stop using the monitor if the cabinet is damaged. Have it checked by a service
technician.
Put your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power
cable immediately and consult your closed dealer.
Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth.
Apply non-ammonia based cleaner onto the cloth, not directly onto the glass screen.
Do not place heavy objects on the monitor or power cord.

2. PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety visual inspections
and the protection afforded by them cannot necessarily be obtained by using replacement
components rated for higher voltage, wattage, etc. Before replacing any of these
components read the parts list in this manual carefully. The use of substitute replacement
parts, which do not have the same safety characteristics as specified in the parts list, may
create shock, fire, or other hazards.

3. SERVICE NOTES
When replacing parts or circuit boards, clamp the lead wires around terminals before
soldering.
Keep wires away from high voltage, high temperature components and sharp edges.
Keep wires in their original position so as to reduce interference.
Adjustment of this product please refers to the user’ manual.

VX2250W-1
ViewSonic Corporation 1 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 4 HANDLING AND PLACING METHODS

VX2250W-1
ViewSonic Corporation 2 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 3 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 2. Specification

2.1 Introduction
1 LCD Pane INX MT215DW01 V1
PANEL Display Area 476.64mm(H)x268.11mm(V) 21.5” diagonal
(1st Optimum color active matrix TFT LCD
source) Resolution 1920x1080
Pixel Pitch 0.24825 mm (H) x 0.24825mm (V)
Glass Anti-Glare type, Hard-coating (3H)
Treatment 1000 :1 (Typ.) 700:1(min)
Contrast Ratio (CR>= 10,000,000:1
Dynamic 10) 170 Deg H and 160 Deg V (Typ.)
Contrast 16.7 M (6-bits + Hi FRC)
Viewing Angle 250 cd/m2 (Typ.) / 200 cd/m2 (min)
LR,UD Tr+Tf: 5ms (Typ.) / 10ms (Max.)
Colors One light bar with White-LED
Luminance 25000 Hrs (Min)
Response N/A (Typ.)
Time
Backlight
Backlight Life
Mercury
2 INPUT Video RGB Analog (0.7 / 1.0 Vp-p , 75 ohms),
SIGNAL DVI-D (TMDS, 100ohms)

Sync Separate Sync / Composite Sync / SOG

Fh = 24 – 83 kHz ; Fv = 50 – 75 Hz
3 COMPATIB PC PC Compatibles (from VGA up to 1920x1080
ILITY Mac Non Interlaced)
Power Mac (up to 1920x1080 )
4 Recommende 1920x1080 @ 60Hz
d
640 x 350 @ 70Hz
RESOLUTI Supported 640 x 400 @ 60, 70Hz
ON 640 x 480 @ 50, 60, 67, 72, 75Hz
720 x 400 @ 70Hz
720 x 480 @ p60, i60Hz
720 x 576 @ p50, i50Hz

VX2250W-1
ViewSonic Corporation 4 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 800 x 600 @ 56, 60, 72, 75Hz
832 x 624 @ 75Hz
1024 x 768 @ 50, 60, 70, 72, 75,
75Hz
1152 x 864 @ 75Hz
1152 x 870 @ 75Hz
1152 x 900 @ 67Hz
1280 x 720 @ p50, p60Hz
1280 x 768 @ 50, 60, 75Hz
1280 x 960 @ 50, 60, 75Hz
1280 x 1024 @ 50, 60, 75Hz
1360 x 768 @ 60Hz
1440 x 900 @ 60, 75Hz
1400 x 1050 @ 60Hz
1600 x 1200 @ 60Hz
1680 x 1050 @ 60Hz
1920x1080 @ i50, p50, i60,
p60Hz
5 CONNECT Video Analog D-sub
ORS
Digital DVI ( Supported HDMI ver. 1.3 /Display port
1.1 spec)

Audio Audio In
3.5 mm jack (green ) for VX2250wm-LED

Power
Internal Power Adapter, 3-pin plug (CEE22)
6
AUDIO Speaker 2Wx2 for VX2250wm-LED only

7 POWER Voltage AC 100-240V (Universal); 50/60 Hz

Consumption Typ/Max 22W (typ.) w/o Audio ,
38 (max; with full load USB hub)

Optimize 19 W(typ.) w/o Audio

ECO Mode

VX2250W-1
ViewSonic Corporation 5 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Conserve 17 W(typ.) w/o Audio

8 ERGONO Tilt 20 ~ -5 degrees

MICS Swivel N/A
Rotation N/A
Height Adjust N/A
9 CONTROL Physical Key [ Power ]
S buttons [ 1 ], [Up], [Dn], [ 2 ]
on the
OSD Function front Auto Image Adjust
panel Contrast/Brightness
Input Select
Main D-SUB, DVI
Menu
Color Adjust
sRGB, 9300K, 7500K, 6500K, 5000K, User
Color [R, G, B]
Information
Manual Image Adjust
H/V Position, Horizontal Size, Fine Tune,
Sharpness,
Dynamic Contrast, Response Time, Aspect
Ratio , ECO Mode
Setup Menu
Language, Resolution Notice, OSD
Position, OSD Timeout,
OSD Background, Auto Power Off

Memory Recall

[ 1 ] : Main Menu
[ 2 ] : Input Select

[Up] or [Dn] : To immediately activate

Contrast and Brightness OSD Menu.
Short cut [Up] + [Dn] : Recall Contrast and Brightness
key to default in its menu without
OSD message.

VX2250W-1
ViewSonic Corporation 6 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 [ 1 ] + [ 2 ] : Toggle 720x400 and 640x400
mode
[ 1 ] + [Up] + [Dn] : Auto White Balance
[ 1 ] + [Dn] : Power Button Lock
[ 1 ] + [Up] : OSD Lock
[ 2 ] + [Dn] : Toggle DDC/CI and DDC/2B
10 BANDWID Analog : 185 MHz
TH Digital : 165 MHz
11 OPERATIN Temperature 32°F to 104°F (0°C to 40°C)
G Humidity 20% to 90% (no condensation)
CONDITIO
N
12 STORAGE Temperature -4°F to 140°F (-20°C to 60°C)°
/ Humidity 5% to 90% (no condensation)
SHIPPING
CONDITIO
N
13 DIMENSIO Physical: Display 521.21 mm (W) x 403.71 mm (H) x
NS (W x H x D) w/ Stand 189.98mm (D)
20.52" (W) x 15.89" (H) x 7.48" (D)
Wall
Mount 521.21 mm (W) x 339.44 mm (H) x 49mm
(D)
Packing (W x 20.52" (W) x 13.36" (H) x 2.63" (D)
H x D)
569 mm (W) x 495 mm (H)x126 mm (D)
22.4" (W) x19.5" (H) x4.9" (D)
14 WEIGHT Net 3.4 Kg (7.5 lbs)
Net (w/o 3.2 Kg (7.1 lbs)
stand) 4.7 Kg (10.4 lbs)
Gross
15 REGULATI UL, CUL, FCC-B (ICES), CB, CE, CES-003B,
ONS ISO13406-2, TUV/GS, ERGO, TUV-S, NOM,
GOST-R, HYGIENIC (20 copies), CCC,
BSMI, PSB, C-TICK, MIC(KCC), SASO,
WEEE, RoHS, SASO, Ukraine
16 RELIABILI MTBF 100,000 Hr (Excluding Panel).

VX2250W-1
ViewSonic Corporation 7 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 TY
17 POWER "On" Blue Normal
SAVING "Active Off" AMBER ≦ 0.1 W
FUNCTION “Off” ≦ 0.1 W
18 LOGISTIC Container Standard 20’: 560 pieces 40’: 1176 pieces for VSA only
S Load 20’: 656 pieces 40’: 1344 pieces for WW.
(20' / 40')
56 sets
Pallet Load

VX2250w 76690744152 9
UPC Code -LED 76690744141 3
VX2250w
m-LED

Serial Format RWT

VX2250w RWS
-LED
VX2250w Byte 10 – 0 x 25, Byte 11 – 0 x CB
EDID Code m-LED
Made in China
Country of
origin
19 Wall Mount VESA 100mm x 100mm
20 OTHERS DDC/2B, DDC/CI, HDCP, Detachable Base,
KENSINGTON MicroSaver Security
Compatible, WorldWide Model, Windows XP,
Vista Premium, Windows 7,
21 Package LCD Display
Contents Power Cable
VGA Cable
DVI Cable
Audio Cable for VX2250wm-LED only
Quick Start Guide
ViewSonic Wizard CD-ROM
22 EU Carton -- One piece construction with double wall,960Kg
Packaging Plastic Handle -- PE-LD, 10g

VX2250W-1
ViewSonic Corporation 8 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Information Poly Foam –640 g
Accessory Plastic Bags -- PE-LD,2 g
The PE bag that cover monitor -- PE-LD, 21 g
Pallet --
For E/M model:
Solid Wood (Fumigation),A 9 kg B 8.5KG
For A/G/J//K/P model:
Poly-wood, A 21 kg B 19KG
Note : P model must use Plywood. And for every P model lot, SI
shall provide plywood certification.
Notes:
The Input Signal and Resolution spec above might be different from segment 4.5.
The display shall fulfill all the criteria in segment 4.5.

2.2 product definition and specification

Product Name ViewSonic VX2250w/wm-LED /

Oracle P/N VX2250W/WM-LED
Model Number VS 13239
English
French
German
Spanish
Italian
OSD Languages Finnish
Russian
Japanese
Korean
Traditional Chinese
Simplified Chinese
TFT LCD Panel and Model # 1st panel: INX MT215DW01 V1
Scalar Novatek NT68668UFG
Input Signal D-Sub /DVI
Sync Compatibility Separate Sync / Composite Sync / SOG
Adapter Internal Power Board
Power Cable (Refer to APPENDIX B) Yes
15 pin mini D-SUB Analog Cable (1.8 m,
black), with PC 2001.
Yes

(Detached cable; refer the Appendix A)

DVI-D Cable(1.8m, black) with PC 2001
Yes
(refer to Appendix A)

VX2250W-1
ViewSonic Corporation 9 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Audio Cable(1.8m, black) with PC 2001 Yes for VX2250wm-LED
MIC Cable(1.8m, black) with PC 2001 No
USB Cable (V2.0)
No
(1.8m, black) with PC 2001

English French
German Dutch
Finnish Swedish
Italian Spanish
Greek Russian
Czech Hungarian
Turkish Polish
ViewSonic CD Wizard
Romania Bulgaria
Slovakia Croatia
Serbia Slovenia
Portuguese Arabic
Japanese Traditional Chinese
Korean Simplified Chinese
Ukraine
English French
German Dutch
Finnish Swedish
Italian Spanish
Greek Russian
Czech Hungarian
Turkish Polish
ViewSonic Quick Start Guide
Romania Bulgaria
Slovakia Croatia
Serbia Slovenia
Portuguese Arabic
Japanese Traditional Chinese
Korean Simplified Chinese

Screen Protector Mylar Yes

Service Insert (Refer to Segment 5.9.3) For Region code = M units only
SRS Insert No
Energy Star Sticker Yes

VX2250W-1
ViewSonic Corporation 10 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 POP Sticker (Refer to Segment 5.8.3) No
Warranty Card For Region code = G units only
Warranty Carton Sticker (refer to F8.1) For Region code = G units only
PE bag of Carton For Region code = G units only
MPR label For India drop shipment only

2.3 General Specification

Test Resolution & Frequency 1920x1080@ 60Hz

Test Image Size Full Size
Factory Default:
Contrast and Brightness Controls
Contrast = 70%, Brightness = 100%

2.4 Video Interface

Input Connector (refer the Appendix A) Analog = DB-15 (Analog)

Digital = DVI-D (Digital)
Default Input Connector Defaults to the first detected input
Equal to twice the weight of the monitor for
Video Cable Strain Relief
five minutes
Refer to Appendix A;
Video Cable Connector Pin out
Compliant DDC/2B and DDC/CI
Video RGB (Analog)
Video Signals Separate Sync / Composite Sync / SOG
TMDS (Digital)
Video Impedance 75 Ohms (Analog), 100 Ohms (Digital)
Maximum PC Video Signal 950 mV with no damage to monitor
Maximum Mac Video Signal 1250 mV with no damage to monitor
Sync Signals TTL
Compliant with version 1.3;
DDC/2B The DDC communication shall not interrupt
when power off.
Compliant with Revision 1.1;
DDC/CI The DDC communication shall not interrupt
when power off.
Digital link protection HDCP
Support HDMI 1.3 and Display Port 1.1 spec.

VX2250W-1
ViewSonic Corporation 11 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Sync Compatibility Separate Sync / Composite Sync / SOG
Shall be compatible with all PC type
Video Compatibility computers, Macintosh computers, and after
market video cards
Resolution Compatibility Refer to Segment 4-5
Exclusions Not compatible with interlaced video

2.5 USB Interface

No USB interface

2.6 Power Supply

Internal Power Supply 36W

Input Voltage Range 90 to 264 VAC
Input Frequency Range 47 to 63 Hertz
Short Circuit Protection Output can be shorted without safety issue
Over Current Protection 5.0A typical at 24VDC
( Protect when short circuit)
Leakage Current 3.5MA (MAX) AT 264VAC / 60HZ
Efficiency (at 115VAC Full Load) Typical: 80%
Minimum: 75%
Fuse Internal and not user replaceable
Power Output VX2250w-LED
<26Watts (typ.)
< 28Watts (MAX)without audio
VX2250wm-LED
<34Watts (typ.)
< 36Watts (MAX)with audio
Ripple and Noise Ripple:<3%
Noise: <1%
Max Input AC Current 1.5A (MAX)
Inrush Current (Cold Start) 80 A MAX./ 240VAC / 50HZ
(COLD START AT 25℃,FULL LOAD)
Power Supply Cold Start Shall start and function properly when under
full load, with all combinations of input voltage,
input frequency, and operating temperature.

Power Supply Transient Immunity Shall be able to withstand an ANSI/IEEE

C62.41-1980 6000V 200 ampere ring wave

VX2250W-1
ViewSonic Corporation 12 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 transient test with no damage.

Power Supply Line Surge Immunity Shall be able to withstand ±1KV (L-L) and
±2KV (L-PE)

(Refer to EN55024:1998 / CISPR24.1997 /

IEC1000-4-5: 1995 / EN61000-4-5: 1995)
Power Supply Missing Cycle Immunity Shall be able to function properly, without
reset or visible screen artifacts, when ½ cycle
of AC power is randomly missing at nominal
input.
The power supply shall not produce audible
noise that would be detectable by the user.
Audible shall defined to be in compliance with
Power Supply Acoustics
ISO 7779 (DIN EN27779:1991) Noise
measurements of machines acoustics. Power
Switch noise shall not be considered.
Power Saving Operation(Method) VESA DPMS Signaling

VX2250W-1
ViewSonic Corporation 13 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250w-LED
Mode LED Power Consumption
On Blue 26 W(typ)
28 W (max)

ECO Blue
22 W (Stand) w/o audio
19 W (Optimize) w/o audio
17 W (Conserve) w/o audio

Power Consumption Mode

Active off Amber ≦ 0.1 W

Off ≦ 0.1 W

VX2250wm-LED
Mode LED Power Consumption
On Blue 34 W(typ)
38 W (max)

ECO Blue 22W (Stand) w/o audio

Mode 19 W (Optimize) w/o audio
17 W (Conserve) w/o audio
Active off Amber ≦ 0.1 W

Off ≦ 0.1 W

Recovery Time On Mode = N/A, Active Off < 3 sec

2.7 Electrical Requirement

Horizontal / Vertical Frequency
Horizontal Frequency 24 – 82 kHz
Vertical Refresh Rate 50 – 75* Hz
Maximum Pixel Clock Analog : 185 MHz
Digital : 165 MHz
Sync Polarity Independent of sync polarity.

VX2250W-1
ViewSonic Corporation 14 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Timing Table

Digital - TMDS
Analog

Composite
Separated
Item Timing Remark

SOG
640 x 350 @ 70 Hz, 31.5 KHz v v v v DMT.
For Separated、 SOG and
Composite sync, switch
1. 640x350@70,640x400@70,
and720x400@70 by [1]+[2]
short cut key ( primary =
720x400@70)
640 x 400 @ 60 Hz, 31.5 KHz v v v v DMT
For Separate,
Composite and SOG
sync, switch
2. 640x400@60Hz and
640x480@60Hz by
[1]+[2] short cut key
(primary =
640x480@60Hz)
640 x 400 @ 70 Hz, 31.5 KHz v v v v DMT
For Separated、 SOG and
Composite sync, switch
3. 640x350@70,640x400@70,
and720x400@70 by [1]+[2]
short cut key ( primary =
720x400@70)
4. 640 x 480 @ 50 Hz, 24.7 KHz v v v CVT
640 x 480 @ 60 Hz, 31.5 KHz v v v v DMT
For Separate,
Composite and SOG
sync, switch
5. 640x400@60Hz and
640x480@60Hz by
[1]+[2] short cut key
(primary =
640x480@60Hz)
6. 640 x 480 @ 67 Hz, 35 KHz v v v v For MAC

VX2250W-1
ViewSonic Corporation 15 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 7. 640 x 480 @ 72 Hz, 37.9 KHz v v v v DMT
8. 640 x 480 @ 75 Hz, 37.5 KHz v v v v DMT
720 x 400 @ 70 Hz, 31.5 KHz v v v v DMT
For Separated、 SOG and
Composite sync, switch
9. 640x350@70,640x400@70,
and720x400@70 by [1]+[2]
short cut key ( primary =
720x400@70).
720 x 480 @ 60 Hz, 31.5 KHz v v v v DTV, For Analog sync, the
10. information OSD shows
640x480
11. 720 x 576 @ 50 Hz, 31.3 KHz v v v v DTV
12. 800 x 600 @ 56 Hz, 35.2 KHz v v v v DMT
13. 800 x 600 @ 60 Hz, 37.9 KHz v v v v DMT
14. 800 x 600 @ 72 Hz, 48.1 KHz v v v v DMT
15. 800 x 600 @ 75 Hz, 46.9 KHz v v v v DMT
16. 832 x 624 @ 75 Hz, 49.7 KHz v v v v MAC
1024 x 768 @ 50 Hz, 39.6 KHz v v v v CVT
For Separated and
Composite sync, Switch
1024x768@50Hz and
17.
1280x768@50Hz by
[1]+[2] short cut key
(primary =
1024x768@50Hz)
18. 1024 x 768 @ 60 Hz, 48.4 KHz v v v v DMT
19. 1024 x 768 @ 70 Hz, 56.5 KHz v v v v DMT
20. 1024 x 768 @ 72 Hz, 58.1 KHz v v v v DMT
1024 x 768 @ 75 Hz, 60 KHz v v v v DMT;
For Separated ,
Composite and SOG,
Switch
21. 1280x768@75Hz and
1024x768@75Hz by
[1]+[2] short cut key
(primary =
1280x768@75Hz)

VX2250W-1
ViewSonic Corporation 16 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 22. 1024 x 768 @ 75 Hz, 60.2 KHz v v v v For MAC
23. 1152 x 864 @ 75 Hz, 67.5 KHz v v v v DMT
24. 1152 x 870 @ 75 Hz, 68.7 KHz v v v v For MAC
25. 1152 x 900 @ 67 Hz, 62.5 KHz v v v v For SUN
26. 1280 x 720 @ 50 Hz, 37.5 KHz v v v v DTV
27. 1280 x 720 @ 60 Hz, 45 KHz v v v v DTV
1280 x 768 @ 50 Hz, 39.6 KHz v v v v DMT
For Separated and
Composite sync, Switch
1024x768@50Hz and
28.
1280x768@50Hz by
[1]+[2] short cut key
(primary =
1024x768@50Hz)
1280 x 768 @ 60 Hz, 47.8 KHz v v v v DMT;
For Composite and
SOG,
Switch
29. 1280x768@60Hz and
1360x768@60Hz by
[1]+[2] short cut key
(primary =
1280x768@60Hz)
1280 x 768 @ 75 Hz, 60.3 KHz v v v v DMT;
For Separated ,
Composite and SOG,
Switch
30. 1280x768@75Hz and
1024x768@75Hz by
[1]+[2] short cut key
(primary =
1280x768@75Hz)
31. 1280 x 800 @ 60 Hz, 49.7 KHz v v v v DMT
32. 1280 x 800 @ 75 Hz, 62.8 KHz v v v v DMT
33. 1280 x 960 @ 50 Hz, 49.4 KHz v v v v DMT
34. 1280 x 960 @ 60 Hz, 60.0 KHz v v v v DMT
35. 1280 x 960 @ 75 Hz, 75.2 KHz v v v v DMT
36. 1280 x 1024 @ 50 Hz, 52.7 KHz v v v v DMT

VX2250W-1
ViewSonic Corporation 17 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 37. 1280 x 1024 @ 60 Hz, 64 KHz v v v v DMT
38. 1280 x 1024 @ 75 Hz, 80 KHz v v v v DMT
1360 x 768 @ 60 Hz, 47.7 KHz v v v v DMT
For Composite and
SOG,
Switch
39. 1280x768@60Hz and
1360x768@60Hz by
[1]+[2] short cut key
(primary =
1280x768@60Hz)
40. 1366 x 768 @ 59.79 Hz 55.9 KHz v v v v DMT
41. 1440 x 900 @ 60 Hz 55.9 KHz v v v v DMT
42. 1440 x 900 @ 75 Hz 70.6 KHz v v v v DMT
DMT;
For Separated ,
Composite and SOG,
Switch
43. 1400 x 1050 @ 60 Hz 65.3 KHz v v 1400x1050@60Hz and
1680x1050@60Hz by
[1]+[2] short cut key
(primary =
1680x1050@60Hz)
44. 1400 x 1050 @ 75 Hz 82.3 KHz v v DMT
45. 1600 x 1200 @ 60 Hz 75.0 KHz v v DMT
46. 1680 x 1050 @ 60 Hz 64.7 KHz v v DMT
DMT;
For Separated ,
Composite and SOG,
Switch
47. 1680 x 1050 @ 60 Hz 65.3 KHz v v 1400x1050@60Hz and
1680x1050@60Hz by
[1]+[2] short cut key
(primary =
1680x1050@60Hz)
48. 1920x1080 @ 60 Hz 67.5 KHz v v DMT
49. 480i @ 60 Hz
50. 480p @ 60 Hz

VX2250W-1
ViewSonic Corporation 18 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 51. 576i @ 50 Hz
52. 576p @ 50 Hz
53. 720p @ 50 Hz
54. 720p @ 60 Hz
55. 1080i @ 50 Hz
56. 1080i @ 60 Hz
57. 1080p @ 50 Hz
58. 1080p @ 60 Hz
*1. Tolerance ≧ ±2KHz. (if no over lapping issue)
*2. Any timing not in the list, it should display as normal or show on “OUT OF RANGE” OSD message
without blanking.

Primary Presets
1920x1080 @ 60Hz

User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO
configuration

Changing Modes
● Maximum Mode Change Blank Time for image stability : 3 seconds (Max), excluding
“Auto Adjust” time
● It should recall factory setting when execute Auto Image Adjust function by following
conditions,
1. Memory recall under DOS mode (640 x 350, 720 x 400 & 640 x 400).
2. New timing mode detected under DOS mode (640 x 350, 720 x 400 & 640 x 400).
● The monitor needs to do “Auto Adjust” the first time a new mode is detected
(see section “0-Touch™ Function Actions”)
● While running Change Mode, Auto Adjust or Memory Recall, the image shall blank

VX2250W-1
ViewSonic Corporation 19 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 3 Front Panel Function Control Description
3.1 Front Panel Hardware Controls
Power Switch AC Power Switch on the back cover
Soft Power Switch on the front bezel
Power LED (Front Head) Blue – ON
Amber – Active Off
Dark = Soft Power Switch OFF
Front Panel Controls (Head) [ ] Power
[ 1 ] [ 2 ] [ ] [▲] [▼] [ 1 ] BUTTON 1
[ 2 ] Button 2
[▲] UP ARROW BUTTON
[▼] DOWN ARROW BUTTON

Note: Power Button, Button 1 and Button 2

must be one-shot logic operation. (i.e. there
should be no cycling)
Reaction Time OSD must fully appear within 0.5s after
pushing Button 1

3.2 Short Cuts Function from the button(s)

[1] Main Menu
[2] Input toggle (Analog or DVI; refer to Appendix D)
To immediately activate Contrast and Brightness OSD
[▼]
Menu.
To immediately activate Contrast and Brightness OSD
[▲]
For Menu.
VX2250w-LED [▼]+ [▲] Recall Contrast and Brightness to default in its menu
without OSD message.(Under Contrast or Brightness
adjust sub-menu, recall Contrast or Brightness to its
default without OSD message. )
[▼] To immediately activate Audio menu.
[▲] To immediately activate Brightness / Contrast menu
[▼]+ [▲] 1. In the Audio mode, recall both of Volume and Mute to
For
default without OSD message.( Under Volume adjust
VX2250wm-LE
sub-menu, recall Volume to default without OSD
D
message.)
2. In the BT / CR mode, recall both Contrast and
Brightness to default in its menu without OSD message.

VX2250W-1
ViewSonic Corporation 20 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 (Under Contrast or Brightness adjust sub-menu, recall
Contrast or Brightness to its default without OSD
message.)
* While OSD menu off, recall CR/ BT/ Audio volume and
mute to default without OSD message

[1] + [2] 1. Toggle 640x350@70Hz, 720x400@70Hz and

640x400@70Hz mode when input 640x350@70Hz or
720x400@70Hz or 640x400@70Hz mode
2. Toggle 640x400@60Hz, 720x480@60Hz and
640x480@60Hz mode when input 640x400@60Hz or
720x480@60Hz or 640x480@60Hz mode
3. Toggle 1024x768@75Hz and 1280x768@75Hz mode
when input 1024x768@75Hz or 1280x768@75Hz
mode
4. Toggle 1280x768@60Hz and 1366x768@60Hz mode
when input 1280x768@60Hz or 1366x768@60Hz mode
[1] + [▼] + [▲] White Balance
(Keep pushing 5 sec) 1. It will not shown on user’s guide
2. OSD message as below,

(Image = no blanking)
3. Recommend environment
3.1. Optical (Best) input timing = 640 x 480 @ 60Hz;
Following timing modes also
recommended,
800 x 600 @ 60 Hz
1024 X 768 @ 60 Hz
3.2. Pattern as below,

[1] + [▲] OSD Lock

VX2250W-1
ViewSonic Corporation 21 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 (refer to segment 4-6-4)
[1] + [▼] Power Lock
(refer to segment 4-6-5)
[2] + [▼] Toggle DDC/CI and DDC/2B (DDC/CI enable/disable)
and show following message for 3 seconds,

When switch to DDC/CI

When switch to DDC/2B

Default = DDC/CI
Signal + [2] + [ ] Factory Mode
Remark : All the short cuts function are only available while OSD off

VX2250W-1
ViewSonic Corporation 22 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 3.3 Factory Defaults
Item Defaults Item Defaults
Contrast 70% Input Priority N/A
Brightness 100% Resolution Notice On
Color Temperature 6500K Volume 50%
(for
VX2250wm-LED)
Sharpness 50% Balance N/A
OSD H. Position 50% Treble N/A
OSD V. Position 50% Bass N/A
OSD Time Out 15 720x400@70Hz /
640x400@70Hz / 720x400@70Hz
640x350@70Hz
DCR OFF 720x480@60Hz /
640x480@60Hz / 640x480@60Hz
640x400@60Hz
OSD Background On 1280x768@60Hz /
1360x768@60Hz / 1366x768@60Hz
1366x768@60Hz
ECO mode Standard

1024x768@75Hz / 1280X768@75Hz
Aspect ratio Full screen
1280x768@75Hz

3.4 AUDIO Interface (SPEAKER SPECIFICATION, For VX2250wm-LED only)

Line input signal 1.0 Vrms @1kHz

Line input impedance 10 Kohm

Maximum Amp power output (Watt) 2.4 W @ SPKVDD=5V 4Ohm

Amp -THD < 10 % THD @1kHz
Speaker Power rating(Ω/Watt) 4Ω/ 2 W
Signal to Noise Ratio 50 db
Frequency response Fo – 20kHz
SPL. 91 dB (at 0.1w/0.1m)
FO 820 Hz
Line input connection 1. 3.5 mm stereo jack

VX2250W-1
ViewSonic Corporation 23 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 There should be no audible vibration
Vibration resonance at volume=100% & any
Freq.

There should be no affect on the screen

Screen image
image stability under any conditions
Connector PC99 requirement Audio in Lime Green pantone # 577C

Cable type / length 3.5mm stereo cable / 1.8m length

SPEAKERS STAY OFF WHEN THE REST
Audio DPMS OF THE MONITOR IS IN POWER
SAVING

3.5 TFT LCD Panel

Panel Characteristics :
1st Source Panel
Model number INX MT215DW01 V1
Type Active Matrix TFT, TN technology
Active Size 476.64mm(H)x268.11mm(V)
Pixel Arrangement RGB Vertical Stripe
Pixel Pitch 0.24825mm
Glass Treatment Anti-Glare
# of Backlights One light bar with white LED
Backlight Life 30000 Hrs (Typ)
25000 Hrs (Min)
Luminance (Center) – 250 cd/m2 (Typ after 30 minute warm up)
CT = 6500K, 200 cd/m2 (Min after 30 minute warm up)
Contrast/ Brightness = Max
Brightness Uniformity 75 % (Typ) / 70 % (Min)
Contrast Ratio DCR Off
1000 :1 (Typ)
700 : 1 (Min)

DCR On
10,000,000 :1 (typ)
Color Depth 16.7 million colors (RGB 6 bit + Hi FRC)
Horizontal Viewing Angle 170 degrees (Typ) / 150 degrees (Min) @ CR>10
Vertical Viewing Angle 160 degrees (Typ) / 140 degrees (Min) @ CR>10
Response Time Tr+Tf: 5ms (Typ.) / 10ms (Max.)

VX2250W-1
ViewSonic Corporation 24 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Mercury 0 mg per lamp
Panel Defects Please see Panel Quality Specifications.
*The average of measured value from monthly shipment shall be equal or better than the Typical value
above.

Packing For Shipping And Disassembly Procedure Packing

For Shipping
1. Packing Procedure
1.1 Paste protection film to protect the monitor. (Figure 1)
1.2 Put the monitor in the PE bag and seal the bag with tape.(Figure 2)

1.3 Put the cushions on the monitor

1.4 Place the monitor into the carton and then put all the accessories into the carton.
At last, close the carton and seal it with tape.(Figure3)

AUDIO CABLE
DVI CABLE
POWER

MONITOR HEAD

Figure 3

VX2250W-1
ViewSonic Corporation 25 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Disassembly Procedure

VX2250W-1
ViewSonic Corporation 26 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 27 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 28 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 29 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 30 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 31 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 32 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 33 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 34 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 35 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 36 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 4. Circuit Description
4.1 Switching Mode Power Supply
4.1.1 AC Current Input Circuit
P801 is a connector for connecting AC Power. F801 is a fuse to protect all the circuit. AC
input voltage is from90V to 264V. R801and R802 joined between two inputting main circuit
to prevent man from shock. L801 is used to clear up low frequency wave. C801 and C802
are used to discharge the waves that L801 produced. High frequency waves are damped
by C801 and C802. D801 is a rectifier which composed of 4 build-in diodes, it invertsAC to
DC.

4.1.2 High Voltage to Low Voltage Control Circuit

C804 is used to smooth the wave from rectifier. IC802 is a highly integrated PWM
controller, which build-in a power MOSFET. When rectified DC high voltage is applied to
the DRAIN pin during start-up, the MOSFET is off initially, and the CONTROL pin
capacitor is charged through a switched high voltage current source connected internally
between the DRAIN and CONTROL pins. When the CONTROL pin voltage Vc reaches
approximately 5.8V, the control circuitry is activated and the soft-start begins. The
soft-start circuit gradually increases the duty
cycle of the MOSFET from zero to the maximum value over approximately 10ms. If no
external feedback/supply current is fed into the CONTROL pin by the end of the soft-start,
the high voltage current source is turned off and the CONTROL pin will start discharging in
response to the supply current drawn by the control circuitry.Resistors R814 are for
external current limit adjustment, and used to reduce the current limit externally to a value
close to the operating peak current of primary about 1.35A. The mean
is power will protected when the primary current over about 1.35A.When PWM is turned
off, the main current flow will be consumed through D802 and ZD802, This will prevent
MOSFET which built-in IC802 from being damaged under large current impulse and
voltage spike. IC801 provide internal Auxiliary current to CONTROL pin during normal
operation. In addition, error amplifier and feedback current to the CONTROL pin are for
duty cycle control.

4.1.3 DC_5V and DC_19V Output Circuit

For DC 5V, D807,D808 and D809 is used to rectify the inducted current. C817 C818
C830and L802 C820 are used to store energy when current is reversed. The parts
including C817 C818 C830and L802 C820 are used to smooth the current waves. For DC
19V, D804 and D805 is used to rectify the inducted current. C816 and C825 are used to
store energy when current is reversed. The parts including C816, C825 are used to
smooth the current waves.

VX2250W-1
ViewSonic Corporation 37 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 4.1.4 Feedback and OVP Protect Circuit
Pin R of IC803 is supplied 2.5V stable voltage. It is connected to 5V and 19V output
through R830,R831 and R823. and R824 are output sampling resistor. When the sampling
voltage morethan 2.5V or less than 2.5V, feedback current of IC802 will change, this can
change the voltage fromtransformer T801.Q804, R822, and ZD801 make up of dummy
loading circuit. For start-up sequence, during 5Voutput take place high loading first, this
dummy loading circuit operated to insure 19V not be increased.
4. 2 LED Circuit
4.2.1 Low voltage to high voltage circuit
19VDC provides the power for IC501; the control signals Brightness and ON/OFF come
from I/F board.ON/OFF signal connect to pin10 of IC501 and makes IC501 enable.
Brightness signal connect to pin1 of IC501and regulates the panel brightness, The
operation frequency is determined by the external Resistor R522 and capacitorR505
connected to pin13 of IC501. BURST MODE regulated dimming
frequency is determined by the external resistor R505 connected to pin13 of IC501. C508
is used for soft start and compensation, C506, R508 are used for dump noise.
The output drives, (pins16 respectively) output square pulses to drive MOSFET U501,
U501 is N channel MOSFET. U501 work as Boost topology, it is high efficient, PWM
switching.
During start up, OVP (pin11) senses the voltage at the output voltage. When OVP
reaches 1V, the output voltage is regulated.
The current flowing through LED is sensed and regulated through sense resistor
R515,R516,R517,R518,R519,R520. The feedback voltage connected to Pin2~Pin5 and
Pin7~Pin10 (ISEN).

4.3 I/F Board Circuit

4.3.1 Power Input
+5V is from the power board and supply for the panel and for the LDO. +3.3V is form the
LDO output used for U105 (Scaler IC: NT68668UFG), and then 3.3V output is generated
from +5V through C101, C104 and C102 filtering, and U101 outputs. +3.3V is only used for
U105.

4.3.2 MCU & Scaler(TSUM1PLR-LF)

The frequency of XTAL1 is 12.000MHz. U105 # 65 is defined as panel_enable. When the
I/O port is high, Q101 and Q104 are conducted. And then after C108 and C109 filtering,
obtain the voltage of VLCD, which will be connected to CN105. U105 # 29 is defined as
VGA_ DET connected with CN102 #5. U105 # 1 is a pin of hardwire reset. U105 # 79-#

VX2250W-1
ViewSonic Corporation 38 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 80,#81-#82, #83-#84, #85-#86,#87-#88 output LVDS digital data of 8 bit to panel control
circuit through CN105. U105 # 117 generates a PWM waveform by regulating the duty to
control the brightness of the backlights.U103 is EEPROM used for saving EDID data,
which is connected by SCL and SDA pins with #35 and #34 of NT68668FG. U108 is a
flash memory, U106 # 6, # 5 are the communications with U105 #49-#50.U106 is
EEPROM used for saving user’s OSD setting.

4.3.3 VGA Input

Signal R, G, B input through CN102 #1, #2, #3, and C116, C117 and C118 filtering the
high frequency noise. Signal HSYNC and VSYNC input through CN102 #13 and #14, and
C129, R135, C130, R136 filtering. Then the analog signal enters U105, and then U108
deals with it internally. In addition, EP112, EP107, EP104, EP105, EP106, EP108, EP109,
EP110, EP111,are ESD protector. Signal DDC-SCL inputs via CN102 #15, and then
passes through EP108 for ESD protection, goes into EDID EEPROM IC U103. Signal
DDC-SDA inputs via CN102 #12, and then passes through EP111 for ESD protection,
goes into EDID EEPROM IC U103. CN102 #5 is defined as cable detect pin, this detector
realizes via R121 and U105 #29,The PC-5V of U103 is supplied by PC via CN102 #9 with
EP107 for ESD protection, or supplied by Monitor self via D106. U103 is an EEPROM IC,
which is a kind of memory and used for saving EDID data.

4.3.4 Button Control

Button “Key-Power” is defined as power on/off, which is connected to U105 #122 through
CN104 #6. Button “Key-2” is defined as two functions of selecting and adjustment, which is
connected to U105 #125 through CN104 #2.
Button “Key-Up” is defined as plus, which is connected to U105 # 67 through CN104 #10.
Button “Key-Down” is defined as minus, which is through connected to U105 #126 through
CN104 # 5.
Button “Key-1” is defined as two functions of menu and exit, which is connected to U105 #
66 through CN104 # 1.
LED indicator on the front bezel is defined as follows:
a. When press button “Key-Power”, U105 # 124 is pulled high and U105 # 123 is pulled
Low, so Q108 is conductedand the LED indicator is Blue.
b. When in power-saving mode, U105 # 123 is pulled high and U105 #124 is pulled down,
so Q106 is conducted andthe LED indicator is orange.

4.4 Power On/Off Sequence

4.4.1 Hardware Power ON
When power cord is plugged into AC socket, SMPS starts work and provides U105 with

VX2250W-1
ViewSonic Corporation 39 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VCC3.3V. When VCC5V inputs, U105 resets circuit active, sets U105 all registers to
preset modes, and then monitor goes into stand-bymode. That means hardware power
on has been completed.

4.4.2 Software Power ON/OFF

When press power key, U105 # 122 recieves low pulse,and then U105 will do the power
on/off.
- If Power ON, U105 # 123(LED Green) will send out Low potential, and then LED Blue on.
- If Power OFF, U105 # 123(LED Blue) will send out High potential, and then LED Off.
The Panel_Vcc, Backlight_En, CLK/DATA output to panel will follow the following
sequency.

VX2250W-1
ViewSonic Corporation 40 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 5. Adjustment Procedure
5.1 Key Function Description
CONTROL
KEYS FUNCTION
KEY

[AUTO] [2] By pressing [AUTO] key, “Auto Image Adjust” is performed

[MENU] [1] By pressing [MENU] key, Main menu display

A. When “MENU OSD” display, press these keys to change the
contents of an adjustment item, or change an adjustment value
[▼] [▲] B. When “MENU OSD” is un-display, press these keys to change
brightness and contrast
[POWER] [ ] Power on or power off the monitor

5.2 Hot Key Operation

[1] Main Menu

[2] Auto Image Adjust
[▼] To immediately activate Audio menu.
To immediately activate Contrast menu. It should be
[▲]
change to Brightness OSD by push button [2]
1. In the Audio mode, recall both of Volume and Mute to
default without OSD message.
[▼]+ [▲]
2. In the BT / CR mode, recall Contrast or Brightness to
default in its menu without OSD message.
1. Toggle 720x400@70Hz 、640x350@70Hz and
640x400@70Hz mode when input 720x400@70Hz 、
640x350@70Hz or 640x400@70Hz mode
2. Toggle 640x400@60HZ ,
720x480@60Hz,640x480@60 mode when input
640x400@60HZ , 720x480@60Hz,640x480@60
mode
[1] + [2] 3. Toggle 1024x768@50Hz and 1280x768@50Hz mode
when input 1024x768@50Hz or 1280x768@50Hz
mode
4. Toggle 1024x768@75/60Hzand 1280x768@75/60Hz
mode when input 1024x768@75/60Hz or
1280x768@75/60Hz mode
5. Toggle 1600x900@60Hz(Reduced) and
1280x960@60Hz mode when input 1600x900@60Hz

VX2250W-1
ViewSonic Corporation 41 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 (Reduced)or 1280x960@60Hz mode
6. Toggle 1600x900@60Hz and 1440x900@60Hz mode
when input 1600x900@60Hz or 1440x900@60Hz
mode
White Balance
1. It will not shown on user’s guide
2. OSD message as below,
[1] + [▼] + [▲]
(Keep pushing 5 sec)

(Image = no blanking)
[1] + [▲] OSD Lock
(refer to segment 4-6-4)
[1] + [▼] Power Lock
(refer to segment 4-6-5)
No signal + [2] + power Burning mode
[2] + power Factory Mode
Remark : All the short cuts function are only available while OSD off

5.3 OSD Control

5.3.1 OSD Table

Main Menu
1. Key button definition:

[1]: OSD off

[2]: Execute the selected function

[Up]: Rolling up the slider

(When push the button on the top position, the slider

shall go down to the bottom item)

[Dn]: Rolling down the slider

(When push the button on the bottom position, the

Level 1 Level 2 Level 3

Auto Image Adjust

VX2250W-1
ViewSonic Corporation 42 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 1. Background = blanking

2. The message OSD position is at the

center.

3. After auto tune, OSD shall be off

4. Only for analog mode

Contrast/Brightness Contrast

1. Adjust range = 0 to 100

2. Default = 70

3. Key button definition:

[1] = Back to Main Menu or OSD off

(depend on previous status)

[Up] = Increase the OSD value setting

[Dn] = Decrease the OSD value setting

[Up]+[Dn]: Recall to default

VX2250W-1
ViewSonic Corporation 43 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Brightness

Key button definition:

[1]: Back to previous OSD status

[2]: select to adjust value setting.

[Up]: Move up the slider

[Dn]: Move down the slider

1. Adjust range = 0 to 100

2. Default = 100

3. Key button definition:

[1] = Back to Main Menu or OSD off

(depend on previous status)

[Up]: Increase the OSD value setting

[Dn]: Decrease the OSD value

[Up]+[Dn]: Recall to default

VX2250W-1
ViewSonic Corporation 44 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Input Select D-SUB

Step 1: Turn off OSD.

Step 2:

1. Target video input port = Analog

2. If signal detected from target port,

change to target port.

3. If no signal detected from target port,

keep existing input port.

Step 3: Show on Input Message OSD at

the right-top corner of screen for 1

1. Show on existing input port by second.

white-background color

2. Key button definition:

[1]: Back to previous OSD status

[2]: Change to the selected input port

[Up]: Move up the slider

[Dn]: Move down the slider

DVI

Step 1: Turn off OSD.

Step 2:

1. Target video input port = Digital

2. If signal detected from target port,

change to target port.

3. If no signal detected from target port,

keep existing input port.

Step 3: Show on Input Message OSD at

the right-top corner of screen for 1

second.

Color Adjust sRGB

Change Color setting to sRGB

9300K
Change Color setting to 9300K

VX2250W-1
ViewSonic Corporation 45 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 7500K
Change Color setting to 7500K

6500K
Change Color setting to 6500K

5000K
Change Color setting to 5000K

User Color Red

1. Show on existing input port by Change Color setting to user color

white-background color

2. Default = 6500K

3. Key button definition:

[1]: Back to previous OSD status

[2]: Change to the selected color

setting 1. Adjust range = 0 to 100

[Up]: Move up the slider 2. Default = 100
[Dn]: Move down the slider 3. Key button definition:

[1]: Back to Color Adjust OSD

4. Under DCR mode (Dynamic [2]: selected setting.
Contrast = On), SRGB shall be [Up]: Increase the OSD value
disabled with fate-out color. And it setting
should not be selected. [Dn]: decrease the OSD value

setting

VX2250W-1
ViewSonic Corporation 46 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Green

1. Adjust range = 0 to 100

2. Default = 100

3. Key button definition:

[1]: Back to Color Adjust OSD

[2]: selected setting.

[Up]: Increase the OSD value

setting

[Dn]: decrease the OSD value

setting

VX2250W-1
ViewSonic Corporation 47 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Blue

1. Adjust range = 0 to 100

2. Default = 100

3. Key button definition:

[1]: Back to Color Adjust OSD

[2]: selected setting.

[Up]: Increase the OSD value

setting

[Dn]: decrease the OSD value

setting

Information

Key button definition:

[1]: Back to Main Menu OSD

VX2250W-1
ViewSonic Corporation 48 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Manual Image Adjust H/V Position Horizontal Position

1. Adjust range = 0 to 100

2. Key button definition:

[1]: Back to Manual Image

Adjust OSD

[2]: Change to Vertical Position

OSD

[Up]: Increase the OSD value

setting

[Dn]: Decrease the OSD value

Vertical Position

1. Key button definition: 1. Adjust range = 0 to 100

[1]: Back to previous OSD status 2. Key button definition:
[2]: Execute the selected function [1]: Back to Manual Image
[Up]: scroll up the slider Adjust OSD
(When push the button on the top [2]: Change to Horizontal
position, the slider shall go down Position OSD
to the bottom item [Up]: Increase the OSD value
[Dn]: Scroll down the slider setting
(When push the button on the [Dn]: Decrease the OSD value

VX2250W-1
ViewSonic Corporation 49 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 bottom position, the slider shall Horizontal Size

go down to the top item

2. Under Digital mode, all the H./V.

Position, Horizontal Size and Fine

Tune shall be disabled with

fate-out color. And it should not be

selected.

3. Under native mode, Sharpness

shall be disabled with fate-out

color. And it should not be

selected.

4. Under SRGB mode, Dynamic

Contrast shall be disabled with 1. Adjust range = 0 to 100

fate-out color. And it should not be 2. Key button definition:

selected. [1]: Back to Manual Image Adjust OSD

[Up]: Increase the OSD value setting

[Dn]: Decrease the OSD value

Fine Tune

1. Adjust range = 0 to 100

2. Key button definition:

[1]: Back to Manual Image Adjust OSD

[Up]: Increase the OSD value setting

[Dn]: Decrease the OSD value

VX2250W-1
ViewSonic Corporation 50 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Sharpness

1. Adjust range = {0 / 25 / 50 / 75 / 100}

2. Default = 50

3. Key button definition:

[1]: Back to Manual Image Adjust OSD

[Up]: Increase the OSD value setting

[Dn]: Decrease the OSD value

Dynamic Contrast
Swap on and off the Dynamic Contrast

function

Default = Off

= On
… = Off

When Dynamic Contrast is on, below

functions will be disabled:

1. Brightness/Contrast menu

2. SRGB selection in Color Adjust

3. White balance hot key

4. DDC/CI BR/CT adjustment

Aspect Ratio 4:3

Change aspect ratio to 4:3

VX2250W-1
ViewSonic Corporation 51 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Full Screen
Fill screen with panel native aspect

ratio.

1. Show on existing Aspect Ratio setting

by white-background color

2. Key button definition:

[1]: Back to previous OSD status

[2]: Change to the selected Display

Mode setting.

[Up]: Scroll up the slider

(When push the button on the top

position, the slider shall go down to

the bottom item)

[Dn]: Scroll down the slider (When push

the button on the bottom position,

the slider shall go up to the top item)

3. Default = full screen

Note : 1.When input signals are wide

format, this function is disable.

2.When input signals are non-wide

format. this function is enable.

ECO Mode Standard

OSD adjust range = 0 to 100

VX2250W-1
ViewSonic Corporation 52 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Optimize
OSD adjust range = 0 to 100

VX2250W-1
ViewSonic Corporation 53 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 1. This function toggles ECO mode. Conserve
2. Show on existing ECO Mode setting by OSD adjust range = 0 to 100

white-background color

3. Key button definition:

[1]: Back to previous OSD status

[2]: Change to the selected Display

Mode setting.

[Up]: Scroll up the slider

(When push the button on the top

position, the slider shall go down to

the bottom item)

[Dn]: Scroll down the slider

(When push the button on the

bottom position, the slider shall go up

to the top item)

4. Default = Standard

5. Under sRGB mode, ECO Mode shall

be disabled with fate-out color. And it

should not be selected.

6. No matter DCR on or off, lamp current

will be changed by ECO mode change.

7. While ECO or DCR setting changed,

the lamp current shall be updated to

new setting immediately.

8. Do not lock Contrast or Brightness

OSD for ECO function

9. Following is the lamp current chart,

57 VX2250W-1
ViewSonic Corporation 54 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Setup Menu Language Select English
Set OSD language to English and

keep in Language Select OSD

French
Set OSD language to French and

keep in Language Select OSD

German
Set OSD language to German and

keep in Language Select OSD

Spanish
Set OSD language to Spanish and

keep in Language Select OSD

1. Show on existing by white-background Italian

color Set OSD language to Italian and

2. Key button definition: keep in Language Select OSD
[1]: Back to previous OSD status
Finnish
[2]: Change to the selected language
Set OSD language to Finnish and
setting
keep in Language Select OSD
[Up]: Scroll up the slider
Russian
(When push the button on the top
Set OSD language to Russian and
position, the slider shall go down to
keep in Language Select OSD
1. Key button definition: the bottom item
Japanese
[1]: Back to Main Menu OSD [Dn]: Scroll down the slider
Set OSD language to Japanese
[2]: Execute the selected function (When push the button on the bottom
and keep in Language Select OSD
[Up]: Scroll up the slider position, the slider shall go down to
Korean
(When push the button on the the top item
Set OSD language to Korean and
top position, the slider shall go
keep in Language Select OSD
down to the bottom item)
Traditional Chinese
[Dn]: Scroll down the slider
Set OSD language to Simplified
(When push the button on the
Chinese and keep in Language
bottom position, the slider shall
Select OSD
go down to the top item)
Simplified Chinese
Set OSD language to Traditional

Chinese and keep in Language

Select OSD

VX2250W-1
ViewSonic Corporation 55 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Resolution Notice
Swap on and off the Resolution Notice

function

OSD Position OSD H. Position

1. Adjust range = 0 to 100

2. Default = 50

3. Key button definition:

[1]: Back to Setup Menu OSD

[2]: selected setting

[Up]: Increase the OSD value

setting (move OSD right)

[Dn]: Decrease the OSD value

setting (move OSD left)

[Up]+[Dn]: Recall to default

value

VX2250W-1
ViewSonic Corporation 56 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 OSD V. Position

1. Adjust range = 0 to 100

2. Default = 50

3. Key button definition:

[1]: Back to Setup Menu OSD

[2]: selected setting

[Up]: Increase the OSD value

setting (move OSD up)

[Dn]: Decrease the OSD value

setting (move OSD down)

[Up]+[Dn]: Recall to default

value

OSD Time Out 5

Set OSD Time Out to 5 Seconds

15
Set OSD Time Out to 15 Seconds

30
Set OSD Time Out to 30 Seconds

60
Set OSD Time Out to 60 Seconds

1. Adjust range = 5, 15, 30, 60

2. Default = 15

3. Key button definition:

[1]: Back to Setup Menu OSD

[Up]: Increase the OSD value setting

[Dn]: Decrease the OSD value setting

[Up]+[Dn]: Recall to default value

VX2250W-1
ViewSonic Corporation 57 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 OSD Background
Swap on and off the OSD Background

= Non-transparent
… = Transparent

Auto Power Off

Swap on and off the Auto Power Off

function

Power off the display automatically when

no signal is detected for 3 minutes.

= On
… = Off

Note :
1. When no signal input with Auto
Power Off = ON, the display will go
into power saving first. After 3
minutes, the display will turn off
automatically.
2. When no signal input with Auto
Power Off = OFF, the display will go
into power saving as normal display.
3. Default = Off
4. Memory Recall will call back the
setting to default.
5. When push Power Lock hot key
under Auto Power Off = On, the
message OSD will show on for 3
seconds (Power Lock function is
disabled),

6. The function will be disabled

when power button locked.
Memory Recall

VX2250W-1
ViewSonic Corporation 58 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 1. Background = blanking

2. Recall white balance to factory

setting

3. Recall all the OSD setting to the

default. (include the R/G/B in User

Color)

4. Show the message OSD position is

at the center for 3 seconds.

5. Clean FIFO timing mode buffer

6. Execute Auto Image Adjust

Note: Memory Recall should not effect

on Language, Power Lock Settings

or Input Priority

5.3.2 OSD Lock short cuts function for the buttons

The OSD lock will be activated by pressing the front panel control buttons [1] + [▲] for
10 seconds *1. If the user then tries to access the OSD by pressing any of the buttons, a
message will appear on the screen for 3 seconds showing "OSD Locked" *2. The OSD
lock will be deactivated by pressing the front panel control buttons [1] + [▲] again for 10
seconds*3.

*1 The OSD Lock message as below,

Range = 0 to 10

*2 The OSD Locked message as below,

*3 The OSD Unlock message as below,

Range = 0 to 10

VX2250W-1
ViewSonic Corporation 59 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 *4 When the OSD is locked will lock all functions, including “Volume”, “Mute” and
others.

*5 Status bar indicating OSD Lock or Unlock is in progress and when complete it will
indicate “OSD Locked” or “OSD Unlocked” for 3 seconds as below,

OSD Locked

OSD Unlocked

*6 When OSD appears on screen, the OSD Lock/Unlock short cut key will be disabled.

5.3.3 Power Lock short cuts function for the buttons

The Power lock will be activated by pressing the front panel control buttons [1] + [▼] for
10 seconds *1. Locking the power button means that the user won't be able to turn off
the LCD while the power button is locked. If the user presses the power button while it
is locked, a message will appear on the screen for 3 seconds showing "Power Button
Locked" *2. It also means that with the power button locked, the LCD would
automatically turn back "On" when power is restored after a power failure. If the power
button is not in the locked mode, then power should return to it's previous state when
power is restored after a power failure. The Power lock will be deactivated by
pressing the front panel control buttons [1] + [▼] again for 10 seconds*3.

*1 The Locking Power Button message as below,

Range = 0 to 10

*2 The Power Button Locked message as below,

VX2250W-1
ViewSonic Corporation 60 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 *3 The Unlocking Power Button message as below,

Range = 0 to 10

*5 Status bar indicating Power Button Lock or Unlock is in progress and when complete
it will indicate “Power Button Locked” or “Button Unlocked” for 3 seconds as below,

Power Button Locked

Button Unlocked

*6 When OSD appears on screen, the OSD Lock/Unlock short cut key will be disabled.

5.3.4 Resolution notice Action

1. Resolution Notice OSD should show on screen after changing to non-native mode
for 30 sec.

2. Key button definition:

[1]: Turn off the OSD message.
[2]: Turn off the OSD message and disable Resolution Notice function
3. The OSD should disappear after 10 sec or by pushing button [1] or [2]

VX2250W-1
ViewSonic Corporation 61 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 4. After the OSD turns off, it will not show on again before next timing change, input
change or power off.
5. Resolution Notice function should be disabled when push button [2] under
Resolution Notice OSD
6. The “1440x900” will be replaced by actual panel resolution.

5.3.5 0-Touch™ Function Actions

1. Execute Auto Image Adjust when new mode detected, and save the settings to
buffer for further use
2. It should be reset by Memory Recall function
(Should not reset by power off, power unplug and others)

5.3.6 OSD Auto Save

The OSD shall save new settings when it is turned off by the user or when it times out.
There shall not be a separate save

5.3.7 Out of range

While non-defined timing is detected, following OSD message will keeps showing on,

1. If the timing is over spec (Fh, Fv or dot clock), the image shall be blanking, and OSD
background shall be non-transparent.
2. If the timing is inspect but not defined, the image shall be non-blanking.

5.3.8 No signal
While no signal is detected for D-Sub and DVI, the following OSD message shall shows
on 3 seconds then go in to power saving.

OSD Background = Non-transparent

Image = Blanking

5.4 EDID (Rewrite EDID data to EEPROM)

If we need to rewrite the EEPROM data, please confirm the following steps.
1. Plug in VGA Cable; we can rewrite the EDID data to EEPROM by using “EDID Rewrite”
program.

VX2250W-1
ViewSonic Corporation 62 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 2. If the “EDID Rewrite” process finished, please pull out VGA cable and press ‘’2’’+’’▲’’ at
the same time.
3. Pull out AC power cable or press power key to restart.

5.5 Upload firmware to MCU via VGA Cable

Connect ISP board between monitor and PC as below configure

Using novatek ISP Tool Update FW:

(1). System Frame

VX2250W-1
ViewSonic Corporation 63 CONFIDENTIAL – DO NOT COPY VX2250WM-1
(2) Function Description
A. ISP ON
Set In-System Programming Enable

B. ISP OFF
Set In-System Programming Enable

C. Load File
Load Hex File to Buffer

D. Erase
Erase MCU Fash Rom

E. Program
Write Buffer Data to MCU Flash Rom

F. Auto
ISP ON→Erase→Promgram→ISP OFF
G. View Hex
View Hex File in Buffer

H. CheckSum
Read Data from MCU

(3). Initial Setting

a. After Setup EasyWriter, We must set EasyWriter settings according our
environment.
b. In “Option”, Select “Setup ISP tool”

VX2250W-1
ViewSonic Corporation 64 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 C.How to Setting
Connect to Novatek ISP Board by USB, Select “NVT EasyUSB”.
USB IIC Speed Limit, Suggestion : Select “Low Speed”.
After Setting, Select “Comfirm Change” to confirm your change.

D.How to Program File to MCU Flash Rom

Step 1. Load Hex File to Buffer
Select “Load File” Button

VX2250W-1
ViewSonic Corporation 65 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Select File Type “Bank Switch(128k, 256k)
Select *.H00(* = FW Project Name(define in KeilC)

Select Confirm, Load File OK

Step 2. Set In-System Programming Enable

Select “ISP ON”, Enable ISP

VX2250W-1
ViewSonic Corporation 66 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Step 3. Erase MCU Fash Rom
Select “Erase”, Erase Flash,Avoid Conflict

Step 4. Write Buffer Data to MCU Flash Rom

Select “Program”, Program Buffer Data to Flash

VX2250W-1
ViewSonic Corporation 67 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Step 5. Set In-System Programming Disable
Disable ISP, Start MCU

Auto Mode
Step2 ~ Step5 = “Auto”
After Step 1,we can select “Auto” directly,to run Program File to MCU Flash Rom

VX2250W-1
ViewSonic Corporation 68 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 6.Troubleshooting Flow Chart
6.1 No Power & Power LED Off

No power

Check primary Check circuit if

Check IC802,
rectifier voltage short
C804, T801,

Check F801, P801,

RT,801,D801

Check pin7 of IC802

CheckC810,D803,C807,
voltage about 16V

Check pin2 of IC802 voltage Check primary OVP, OLP

about 3V and secondary

Check pin5 of IC802 Check R804, R805

voltage is below 1.4V

END

VX2250W-1
ViewSonic Corporation 69 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 6.2 DC output voltage is unstable

Unstable power

Check
Check sampling
R822,R825,R826,
Circuit

R822,R825,R826,

Check the R pin Check the C pin

Change
voltage of IC803 voltage of IC803

Check R832

Check pin7 of Check D803,C807,C810 if

IC802 voltage short

Change

Check pin3 of Change

IC802 voltage R833,R835,R805,R834

END

VX2250W-1
ViewSonic Corporation 70 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 6.3 Output power is unstable

No raster?
Yes
LED Green?
Yes

Backlight can’t be
turned on.

Yes

No
I Check power
Invert supply

No Yes
Is there high-level voltage on Check I/F board
Is Ok R
pin6 of IC501? SCALER

Yes
No R505 open
No
Are connected rightly Connecting the
CN501, CN502, CN503 output connector
again
Yes
Yes
Is there instantaneously pulse wave No
U501, U502 fail
on pin1, pin16 of IC501 at the moment of Is Ok IC501?
restart?
No IC501 fail
Yes
No
T501, T502 fail
Is ok T501, T502?

Yes

Check feedback circuit

ISEN1,ISEN2,VSEN,OLP1,OLP2 END

VX2250W-1
ViewSonic Corporation 71 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 6.4 Backlight can’t be turned on

Black Screen

NG
Check VCC
Power Fail
5V

OK
NG Check
Check VCC3.3V and
VCC1.8V FB103

OK

Check

FB102

NG
Check Reset
Check C151
Waveform

OK

NG
Check Crystal
Check
pin(96,97)waveform
Waveform

OK

OK OK
Check CCFL Check
Invert fail
Enable pin10 of

NG NG
Check R147,R111,R112,
U104 fail
and Q106

VX2250W-1
ViewSonic Corporation 72 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 6.5 White Screen

White Screen

OK
LVDS cable Workmanship
reinsert

NG

OK
Change LVDS LVDS cable NG
cable

NG

OK
Check VLCD OK Check VLCD Panel Fail
Is 5V
singals

NG

Check panel Enable

of Panel Enable

OK

Check CN104
Check

Q101,Q103 and

END

VX2250W-1
ViewSonic Corporation 73 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 6.6 Bad Screen

Bad Screen

OK
Workmanship
LVDS Cable
Reinsert

NG

Change LVDS
Cable

NG

NG
Check Crystal :pin Check X1,C150 and
127 and pin128 C152

OK

checkU105and
SDO/SCZ/SCK/SDI
SDO/SCZ/SCKSDI /RSTN

VX2250W-1
ViewSonic Corporation 74 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 7. Block Diagram

VGA Input
VGA Input
Circuit

DDC
Flash Panel

24c02
SCALER
5V Switch
(NT68668)
to Panel
DVI Input
DVI Input
Circuit Back lamp

ON/OFF
DDC 5V to 3..3V
EEPROM
24c02 24C16

Key Input Key&LED

ON/OFF

EMI Filter Rectifier& Rectifier 5V Switch

AC Input
Circuit Filter Circuit Power filter 5V to inverter
Switch Output Protection
transformer feedback
MOSFET Switch B
PWM Control Rectifier
Circuit filter 14V
Output LED Driver
Volume Control Sampling
5V Input Voltage
Sampling
MCU Voltage
Photocoupler
Audio Amplifier feedback
(PAM8603)
Speaker
1

Audio Input
VX2250W-1
ViewSonic Corporation 75 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 8. Schematic Diagrams

CN901
Reset
8 VCC5V
7 SCL
6 SDA
5 LED_Y
4
3 LED_B
2 Power
1
CN902
8P 1.25mm 90°
5
4
3
2
1

5P 1.25mm 90°

ZD901

LED901

ZD903
3

2
SW901 SW902

ZD902
1

1
2

2
5V6/NC

5V6/NC
5V6/NC

1
POWER

VX2250W-1
ViewSonic Corporation 76 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 A_VCC5V A_VCC5V

R706 10K/NC
R701

10K

R702 NC/0 VOL

R705 0 Shutdo wn
CN705 Power Board

3
3
R_OUT- 16 15 L_OUT - R703 100 1 Q701
ROUT- LOUT- ROUT- LOUT - VOLU ME
MUTE 1
R_OUT + 14 L_OUT+ PMBT3904
ROUT+ LOUT+ ROUT+ 13 LOUT+
Q702

2
AR 12 11 HDMI_AUDIO_R PMBT3904/ NC

2
AR AR HDMI_AUDIO_R
AL 10 9 HDMI_AUDIO_L
AL AL HDMI_AUDIO_L
EarOutR 8 7 MUTE
SHUT EO_R MUTE
EarOutL 6 5 VOLU ME
VOL EO_L VOLU ME
Hp/Sp 4 3 AUDIO_SW
AGND Hp/Sp AUDIO_SW
2 1 A_VCC5V
+5V GND A_VCC5V

2*8P 2.54mm 180°

FB703
120Ω 3A
LOUT _P LOUT+
Z1 Z2 Z3

C702 Mark Mark Mark

470p/50 V C703 100p/50 V

C706 100p/50 V
C710
FB701
A_VCC5V 120Ω 3A 470p/50 V
A_VCC5V LOUT_P 1 24 ROUT_P LOUT_N LOUT-
+OUT_L +OUT_R
10u/25V

10u/25V
2 23
1u/16V

PGNDL PGNDR

C718 1u/16V
FB702
C712 0.1/16V

3 PGNDL PGNDR 22
120Ω 3A
LOUT_ N 4 21 ROUT_N ROUT_N ROUT-
-OUT_L -OUT_R
C713

C716

C719
5 PVDD PVDD 20
C701
FB705 Shutd own 6 19 Shutdo wn
MUTE SHDN
60Ω 3A 470p/50 V
A_VCC5V 7 PAM8603M 18 C704 100p/50 V
C714 4.7u/16V

VDD GND
AL_IN C723 0.47/16V 8 17 C725 0.47/16V AR_IN C705 100p/50 V
INL INR
C708
0.1u/16V

C726 0.47/16V/NC9 16 C727 0.47/16V/NC FB704

EarInL EarInR
120Ω 3A 470p/50 V
10 15 R711 100K/NC Hp/Sp ROUT_P ROUT +
VDC LINE/EAR A_VCC5V
VOL R704 10K 11 14 R712 100K/NC
Volume VREF
C717

EarOutL 12 13 EarOutR
EarOutL EarOutR

5P35V
5P35V

4.7u/16V
U701
C731 C730
1u/16V

C724 0.1/16V

1000p/50V/NC 1000p/50V/NC

EP703
C715

C720
RI R707 0 AR_I AR_IN
EP704

LI R708 0 AL_I AL_IN

C721 4700p/50V

C722 4700p/50V
10K

10K
R709

R710
A_VCC5V

A_VCC5V C743
0.1/16V A_VCC5V
R717

R718

U702 R721 R723

AL_I 1 14
1A VCC 100K/NC 100K/NC
2 GND 1S 13
100K/NC

100K/NC

AL L C734 0.1/50V LI 3 12
1B0 1B1 HDMI_Audio_L
AR R C735 0.1/50V RI AR_I 4 11 Pin6(1B1) HDMI
2A VCC
Audio L input
R713 5 10
R714 GND1 2S
6 2B0 2B1 9 HDMI_Audio_R
5.6K/NC 7 8 Pin4(2B1) HDMI
5.6K/NC NC NC1 R722 R724
R719

R720

Audio R input

FSA225 7
100K/NC 100K/NC
100K/NC

100K/NC

A_VCC5V

AUDIO_SW

Pin10,13 Connect to MCU GPIO

to Switch PC_HDMI_Audio

VX2250W-1
ViewSonic Corporation 77 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 1000p/50V
C901
8

1
R904 1TP4 TP904
U901 560

I2C SDA

I2C SCL
GP1[0]

GP0[1]

GP0[0]

GP0[4]

CSlnt

GP0[3]
R903 1TP3 TP903
560
CY8C20160

560 R902 1 TP902

560 R901 1TP1 TP901

GP1[1]

GP1[2]

GP1[3]

GP1[4]

GP0[2]
XRES

VDD
Vss
CN903

10

11

12

13

14

15

16
+3.3V

9
R905 0.1/16V
6 C902
5 SCL 10K Z903 Z904
4 SDA
3
2 Mark Mark
1

6P 90°
+3.3V

VX2250W-1
ViewSonic Corporation 78 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 Note 2
VGA5V
Note 1 1 D103
3
CN101 +5V 3 VGA 5V BAV70 Note 5

C124 1000p/50V
C166 1000p/50V
2
1
2 U102
To Power/Inverter

3 +3.3V AS1117L-1.8TR-LF/NC +1.8V

4
5 3 VIN VOUT 2
LED_ON/OFF +1.8V 5
6

ADJ
7 Brightness 5 PAD 4
8 Volume 5
GND
Board

+
9 Mute 5
C106 C103/NC C107/NC

1
10 PSC 5
22u/16V 0.1/16V
1000P/50V

1000P/50V

1000P/50V

1000P/50V
1000P/50V 1000P/50V
10P 2.0mm DVI5V
1 D104
VCC5V 5
3
4 DVI5VC125 2 BAV70

1000p/50V Note 4
C160

C161

C162

C163

C164

GND
+5V Note 3 U101
GND D101 SSM24APT AS1117L-3.3TR-LF +3.3V
DIO--SMA 3 VIN VOUT 2
GND +3.3V 3,4,5

ADJ
R101 0 R0805 4
PAD
C104 +
C101 + C102

1
100u/16V 0.1/16V 100u/16V

+3.3V

R111 Q101
GND VCC5V AP2305GN VLCD
R140 2 3 VLCD 5
47K
4K7
LED_ON/OFF R112

0.1/16V
C108 51

100u/16V
3

0.1/16V R0402

1
1 Q103 R109
5 LED_ENABLE

3
PMBT3904 100K
R106 +
100K GND 1
2

C109

C110
R107

3
Q102

2
100K
1 2N7002
5 PANEL_ENABLE Q104
GND C112 R108 PMBT3904
1u/16V 47K

2
GND GND

Note:
1. Pin2 of CN101 need to NC for PCBA use.
2. PC5V can be used for scaler on power saving mode.
3. D101 must be co-layed with R101. D101 is used for ESD back drive.
4. U101 must contain TO263, TO252 and SOT223 package.
5. Using embedded 3.3 to 1.8 LDO NC U102 ,C106 ,C107 and C103

VX2250W-1
ViewSonic Corporation 79 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 +1.8V CVDD Note 1

AVCC_3V3 ADC_BIAS VAA_3V3 FB108 120Ω Note5

+3.3V +3.3V
+3.3V DVDD_3V3 Note 1 Note 1 Note 1
2,3,4 +3.3V FB104 FB107 FB106
FB102 Note 1 CN103

C148 100p/50V
30P 1.0mm

C123 100p/50V
C135 C137 C153

C155 0.1/16V
C122 100p/50V
120Ω 30Ω 120Ω

C144 0.1/16V
C154 0.1/16V
0.1/16V 0.1/16V 0.1/16V

0.1/16V

0.1/16V
C111 100p/50V
30Ω
C139 RXO0-

C142 0.1/16V

C152 0.1/16V

C156 0.1/16V
1u/16V C138 RXO0+ 30

C143

C159
+
C141 + C150 + 22u/16V RXO1- 29
22u/16V 220u/10V RXO1+ 28
RXO2- 27
VAA_1V8 RXO2+ 26
25
FB109 120Ω 24
RXOC-
GND RXOC+ 23
GND GND GND RXO3- 22
C147 C146 RXO3+ 21
4.7u/10V 0.1/16V RXE0- 20
RXE0+ 19
18
RXE1- 17
RXE1+ 16
15
Note: RXE2- 14
13
1. Each bypass capacitor (0.1u/16V) must be closed to pin that si DC power input of scaler IC. RXE2+
12
RXEC-
2. LED green driving circuit is reserved for some model. RXEC+ 11
3. Bypass capacitor C167,C168,C169,C170,C171,C172,C173 are for ESD and EMI issue. ESD component RXE3- 10
Note 4 RXE3+ 9
EP101,EP102,EP103 are for GPIO direct driving LED. 8
4. RL111,RL112,RL113,RL114 are reserved for some panel spec. RL111 0 LPIN6 7
6
5. CN103 is no locked packgae for normal model CN105 for 15.6w&18.5w B type single LVDS input RL112 0 LPIN5
5
panel. RL113 0
4
6. Pin2&Pin4 of CN104 need to NC for PCBA use. ADC_BIAS 3
VLCD 2
+3.3V VAA_1V8 GND 1

C133 AVCC_3V3 CON--FOX-HS9030E

FB110 120Ω 4.7u/10V CVDD VAA_3V3 DVDD_3V3
2 VLCD
FOR Tw215N2
AVCC_3V3
AVCC_3V3
C136
0.1/16V

Note5

115
119

116
45

43

52

26

15

17
28

51

90

53
6

2
CN105
AVCC_3V3

PLL_DVDD

PLL_GND

CVDD
CVDD
CVDD_ZP

ADC_VAA18

AVCC
AVCC

ADC_BIAS
ADC_VAA33

DVDD
DVDD
DVDD
DVDD_ZP

NC
R146 16 REXT DGND/CGND 100
DVDD_3V3 470 1% 99 30
DGND/CGND
C165 4 RX2+ 4 RX2+ DGND/CGND 98 29
0.1/16V 4 RX2- 5 RX2- DGND/CGND 97 28
4 RX1+ 7 RX1+ DGND/CGND 96 RXO0- 27
R189 R190 4 RX1- 8 RX1- DGND/CGND 95 RXO0+ 26
10K 10K GND U108 4 RX0+ 10 RX0+ DGND/CGND 94 25
8 2 SDO SDO 4 RX0- 11 RX0- DGND/CGND 93 RXO1- 24
VCC SO SCS 13 92 23
7 HOLD# CS# 1 SCS 4 RXC+ RXC+ DGND/CGND RXO1+
WP_FW 3 6 SCK SCK 4 RXC- 14 RXC- DGND/CGND 91 22
WP# SCK 21
4 GND SI 5 SDI SDI
RXO0-
RXO2-
R192 R191 T0M 88 RXO2+ 20
47K 1K PM25LV010A-100SCE 41 87 RXO0+ 19
3 HSYNC HSYNCI1 T0P RXO1-
3 VSYNC 42 VSYNCI1 T1M 86 RXOC- 18
85 RXO1+ 17
T1P RXO2- RXOC+
GND 3 BLUE+ 19 84 16
BIN1+ T2M RXO2+
GND 3 BLUE- 20 BIN1- T2P 83 RXO3- 15
82 RXOC- 14
TCLK1M RXOC+ RXO3+
3 SOG 21 SOG1I TCLK1P 81 13
22 80 RXO3- 12
3 GREEN+ GIN1+ T3M RXO3+
3 GREEN- 23 GIN1- T3P 79 11
77 RXE0- 10
T4M RXE0+
3 RED+ 24 RIN1+ T4P 76 9
25 75 RXE1- 8
+3.3V 3 RED- RIN1- T5M RXE1+
+5V 74 7
T5P RXE2-
3,4 WP_EDID 38 PA5/PWM7* T6M 73 6
34 72 RXE2+ 5
3 DDC_SDA_VGA PB7/DDC_SDA1* T6P
35 71 RXEC- 4
3 DDC_SCL_VGA
4 DDC_SDA_DVI 46
PB6/DDC_SCL1*
PB5/DVI_SDA0*
U105 TCLK2M
TCLK2P 70 RXEC+ 3
R177/NC 47 69 RXE3- 2
4 DDC_SCL_DVI PB4/DVI_SCL0* T7M RXE3+
2K2 68 1
R103 SCS 104 SPI_CE NT68668 T7P VLCD
2

SDO 105 62
LED_B_C 110K SPI_SO VCKI
Q107 1 SDI 106 61
PMBT3906 SCK SPI_SI V7 GND 30P 1.0mm
107 60
R166 WP_FW SPI_CLK V6 CON--FOX-HS9030E
5V_DET 108 PD4 V5 59
10K 58
3

R165 V4
V3 57 +3.3V
330 +3.3V 56
R144 V2
R0603 55
10K/NC

200K V1
47K
47K

5V_DET 30 54
TX 31 PB3/ADC3/INTE1 V0
TP1 P31/TXD
LED_B R167 RX R147 100 VSO R171 R138 R137
TP2 32 P30/RXD INT_VSO 113
R0603 100/NC R148 100 HSO 10K/NC 4K7 4K7 C140
33 PB2/ADC2/INTE0 INT_HSO 114
0.1/16V
R186
R185

R184

36 103 VSO
PA3/PWM5 PC7 HSO U106
37 PA4/PWM6* PC6 102
R125 1K 29 8 VCC A0 1
3 VGA_DET PD6 E2P_WP R145 1K 7 2
39 PA6/PWM8* WP A1
4 HPD_CTRL R216 1K +3.3V IICSCL R142 100 6 3
4 DVI_DET 40 PA7/PWM9* SCL A2
+3.3V IICSDA R143 100 5 4

100K
10K/NC
10K/NC

10K/NC
10K/NC
SDA GND

R172 100K/NC
10K
100K
100K
100K
100K

R174 100K
Note2 AT24C16AN

R173 100K
E2P_WP R139 100 GND
48 PD5
DVDD_3V3 IICSDA 49 P35

R195

R182
R181
R180
R178

R196
R179
R176/NC IICSCL

R194
R193
R183
50 P34
4K7
R175
2

126 R157 0 TOUCH POWER

47K PB0/ADC0
Q108/NC 1 Power 125 R158 0 ENTER TOUCH SCL
PMBT3906 PB1/ADC1 LED_A_C
R169 10K/NC PC5 124
1 123 LED_B_C
RSTB PC4/PWM1 POWER
122
3

C151 PC3/PWM0
R168/NC 1u/16V R199
121 100 Mute 2
51 PC1* R153
R170 120 100 PSC 2
R0603 PC0* R154
UP
0改為1K 118 100 Volume 2
Power C157 R197 100 127 PWMB*
OSCI PWMA* 117 Brightness 2
22p/50V 110
R0603 PC2 LED_ENABLE 2
R160
2

X101 67 R188 0 TOUCH SDA

PA1/PWM3 R187 1K RERET
PA2/PWM4 66
DGND/CGND
DGND/CGND
DGND/CGND

DGND/CGND
DGND/CGND

+3.3V 1M 65
ADC_GNDA

PA0/PWM2 PANEL_ENABLE 2
12MHz

10K
1

DGND

DGND
DGND
PGND
AGND
AGND

C158 R198 100 128

GND

GND

22p/50V OSCO

R102
R161
除LED_Enable和Brightness外未變，
109

101

112
111

其他為Lowpower設計，被NC掉的全為與KEYPAD有關
44

64
78

18
12

27
89
63

2K2/NC
3

9
2

Q106 1 LED_A_C GND

PMBT3906
R162
10K
3

R163
500 Note6
R0603 CN104

LED_A R164/NC Touch SCL 2 1 RESET

R0603 100
4 3

POWER 6 5 TOUCH POWER

GND 8 7 LED_B

TOUCH SDA 10 9 LED_A

2x5P 2.0mm
5P35V

1000P/50V

1000P/50V
C1671000P/50V/NC

C1721000P/50V/NC

5P35V

To Keypad Board
Note3
C168

C169
EP101

EP102

VX2250W-1
ViewSonic Corporation 80 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 IC501
INL858

5 BRIGHTNESS 1 24
PWM STATUS
R501 R508 C506
ISEN1 2 23
10K C501 ISEN1 NC 100 0.47/50V
1000p/50V
ISEN2 3 22
ISEN2 SSTCMP CN501
CONN LED
ISEN3 4 21
ISEN3 COMP
ISEN6 R520 10
+19V ISEN2 ISEN1 ISEN4 5 20
CN502 ISEN4 SEL 10 9
CON 8PIN R526 C503 0.47/50V ISEN5 8
0 6 GNDA VIN 19 R519 7
1 10 6
1 ISEN4 ISEN3 ISEN6 7 18
2 2 ISEN6 GNDP 5
3 3 ISEN7 4
4 R527 8 ISEN7 VREF 17 R507 R509 3
4 0 1K
5 5 ISEN8 NC 2
6 ISEN6 ISEN5 9 ISEN8 LDR 16 ISEN4 1
6 R518
7 7 ISEN5
8 R528 10 ISEN5 ISW 15 10
8 0
R504 OVP 11 14
OVP ENA
10K 1%
12 ISET RT 13
R505 2.2U/50V 2.2U/50V
140K 1%
C505 C509 CN503
R525 CONN LED
NC R517
5 ON/OFF
ISEN3 10 10
R502 9
10K R503 ISEN2 8
470K C502 R516 7
1000p/50V 10 6
5
R524 4
C507 10 3
100P 2
ISEN1 R515 1

R506 R523 10
100 1% 100
C5081000P R53210 R529R530 R531
10 10 10
CN504
CONN LED
ISEN2 6
D501 5

2
L501 U501AP9971GH SB200 R513 4
C504 33uH 300K 3
2.2u/50V 1 ISEN4 2
ISEN6 1
D502 OVP
3

SB200 C511 C512

1u/100V 1u/100V C513
10u/100V
R512 R511 R510
0.51 0.51 0.51 R514
11K C510
220p/50V

VX2250W-1
ViewSonic Corporation 81 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 +5V
CN201 DVI5V
DVI-D_CON

C105 C145
DVI_RX2- R201 10 1000p/50V 1000p/50V DVI5V 2
RX2- 1 RX2- 5
2 DVI_RX2+ R202 10
RX2+ RX2+ 5
GND 3

1
9 DVI_RX1- R203 10
RX1- DVI_RX1+ RX1- 5 D201
10 R204 10 GND BAV70 C201
RX1+ RX1+ 5
19 0.1/16V
GND DVI_RX0- R205 10
RX0- 17 RX0- 5
18 DVI_RX0+ R206 10

3
RX0+ RX0+ 5
22 R211 R212 R213
GND DVI_RXC+ R207 10
23 RXC+ 5 100K 100K 10K
RXC+ DVI_RXC- R208 10 U201
RXC- 24 RXC- 5 R214
1K 8 VCC A0 1
7 WP A1 2
6 DVI_SCL R209 100 6 3
SCL DVI_SDA R210 100 SCL A2
SDA 7 5 SDA GND 4
VS 8
AT24C02BN
WP_EDID 3,5
DDC_SCL_DVI 5
5V 14 DDC_SDA_DVI 5
15 DVI_DET DVI_DET
GND DVI_DET 5
16 HPD_DVI HPD_DVI GND
HP
RX4- 4
5 DVI5V
RX4+ DVI5V
GND 11
12 D202 D204 D206 D208
RX3- DVI5V 2
3

3
13 BAV99 BAV99 BAV99 BAV99
RX3+
RX5- 20 2 1 2 1 2 1 2 1
Note 1

5P35V

5P35V
5P35V

5P35V
RX5+ 21
DVI5V R217 10K

0.1/16V

0.1/16V
R218
5P35V

C203 C205 C207 C209 100/NC

+5V HPD_DVI
0.1/16V

0.1/16V 0.1/16V 0.1/16V 0.1/16V ZD101

R219

3
D203 D205 D207 D209 Q201

100p/50V
47K
3

3
6V2 PMBT3904

C212

C213
C214 0.1/16V

EP203

EP204
EP202

EP205
BAV99 BAV99 BAV99 BAV99 1 HPD_CTRL 5
C202
EP201

2 1 2 1 2 1 2 1

2
HDCP Function

C215
C204 C206 C208 C210
0.1/16V 0.1/16V 0.1/16V 0.1/16V GND

GND

Note:
1. R218 is reserved for some model.

VX2250W-1
ViewSonic Corporation 82 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 CN102 Note 2
DZ11AA1-H5W6-4F
11 1 R RB101 0 R114 75 C113 0.047u/16V
+5V RED+ 5
6 R0603
CN201 G RB102 0 R115 75 C114 DVI5V
0.047u/16V
12 2 GREEN+ 5
DVI-D_CON R0603
7
13 3 B RB103 0 R116 75 C115 0.047u/16V
C105 C145 BLUE+ 5
R0603

75 1%
8

75 1%

75 1%
DVI_RX2- R201 10 1000p/50VR159
1000p/50V DVI5V 2
RX2- 1 14 4 VGA5V RX2- 5 470 1% C134 0.047u/16V
2 DVI_RX2+ R202 10 C116 SOG 5
RX2+ 9 Note 1 C117
RX2+ C118
5
GND 3 15 5 10p/50V 10p/50V 10p/50V

1
9 DVI_RX1- R203 10
RX1- 10 RX1- 5 D201

R117

R118

R119
DVI_RX1+ R204 10 GND
RX1+ 10 RX1+ 5 BAV70 C201
19 R122 75 C119 0.047u/16V 0.1/16V

0
GND DVI_RX0- R205 10 RED- 5
16

17
17

0
RX0- DVI_RX0+ RX0- 5
18 R206 10

3
RX0+ RX0+ 5 R123 75 C120 0.047u/16V
22 R211 R212 R213 GREEN- 5
GND DVI_RXC+ R207 10
23 100K 100K 10K
R124 75 C121 0.047u/16V

R120

R121
RXC+ DVI_RXC- RXC+ 5 BLUE- 5
24 R208 10 R214 U201
RXC- RXC- 5
VGA_DET 8 VCC
1K VGA_DET A0 1
7 WP A1 2 VGA_DET 5
6 DVI_SCL Note 3 R209 100 6 SCL 3
SCL A2
7 GND DVI_SDA R210 100 5 SDA 4

5P35V

5P35V

5P35V

5P35V
SDA GND
8
5P35V

VS AT24C02BN
WP_EDID+5V VGA5V
C126 0.1/16V

3,5
DDC_SCL_DVI 5
5V 14 DDC_SDA_DVI 5
15 DVI_DET C127 DVI_DET
EP107

EP104

EP105

EP106
GND DVI_DET 5
16 HPD_DVI 0.1/16V HPD_DVI VGAGND
5V 2
EP112

HP

1
RX4- 4 D106
5 DVI5V BAV70
RX4+ DVI5V
GND 11
12 D202 D204 D206 D208 C128
RX3- DVI5V 2
3

3
13 BAV99 BAV99 BAV99 BAV99 0.1/16V

3
RX3+
RX5- 20 GND 2 1 2 1 2 1 2 1 GND
Note 1

5P35V

5P35V
5P35V

5P35V
RX5+ 21
DVI5V R217 R129 10K

0.1/16V

0.1/16V
R127 R128 R218
5P35V

C203 C205 C207 C209 100K 100K 10K 100/NCU103

+5V HPD_DVI R130
0.1/16V

0.1/16V 0.1/16V 0.1/16V 0.1/16V 1K 8 VCC A0 1

ZD101
7 WP A1 2
VGA_SCL R131 100 6 SCL
R219 A2 3

3
D203 D205 D207 D209 Q201

100p/50V
VGA_SDA R132 100 5 SDA
47K GND 4
3

3
6V2 PMBT3904

C212

C213
C214 0.1/16V

EP203

EP204
EP202

EP205
BAV99 BAV99 BAV99 BAV99 1 HPD_CTRL 5
C202
EP201

2 1 2 1 2 1 2 1 AT24C02BN
FB101 GND

2
120Ω HDCP Function
WP_EDID 4,5

C215
C204 C206 R133
C208 100 C210
HSYNC 5
0.1/16V 0.1/16V R134
0.1/16V 100
0.1/16V VSYNC 5 DDC_SCL_VGA 5
GND
DDC_SDA_VGA 5
33p/50V

33p/50V
5P35V

5P35V

5P35V

5P35V

2K2

2K2

Note 3
GND C131 C132
33p/50V 33p/50V
C129

C130
R135

R136
EP108

EP109

EP110

EP111

GND
GND

Note:
1. R218 is reserved for some model.
Note:
1. R120 is reserved for Samsung model.
2. R0603 package for Bead. C116,C117,C118 are reserved for EMI or performance issue.
3. C131,C132 are reserved for tuning performance issue.

VX2250W-1
ViewSonic Corporation 83 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 R815 C814
100R 1n 500V

C805 1 2
4700p/250V T801 D804
+19V
SPW-XXX SB540
3 D805 ZD801 R821
11 SB540 510R 2W
+ + C816 C813 27V
C806 12 C825 220u/35V

3
R807 4700p/400V 220u/35V R819
33K 0.1/50V 200R Q801
2
+ 1
R818 C815 2N4401
+ ZD803 2 22R 2.2n 500V
P6KE150A R822

1
1 2 10K
3 2
D801 C804 7
BL4-06 82u/450V
8
-

D807
VCC 5V
SB540 L802
4

1
CN805 D802 D808 5uH F802
MUR1100ERL SB540 R839 5A/125V A_VCC5V
6
12 C824
HV D803
3 2
+ 1N4003 9 C830 C818 C817 C820
L801 C807 680u 10V 680u 10V 680u 10V 680uF 10V 0.1/50V 0.22R 2W C819
NC 11
20mH 47u/25V 10 680uF 10V
1 4 5
NC 10
C821
2200P Y1/NC
CS 9
R824

2
C808 110K 1%

2
1
8 NC R825 R823
NC

1
270R C823 R828 7.5k 1%
IC801 10nF/50V 4.7K
R801 7 4 1
3M D 2 1 2 1
C803 R836
6 3 2 200R 1%
NC

1
LTV817M R829

2
0.22u X2 5 NC C828
FB 0.1/100V

NC 4

RT801 C
5R 3 R814
GND 0R62 2W R
A IC803

1
250V 2 TL431 R830 R831

1
NC

2
10K 1%
10K 1%

2
CON10PIN
F801 1
VCC
3.15A/250V

C801 CN801
2200P/250V Y1 C802
2200P Y1 CN802
1 I2S_WS_LRCK
2 I2S_DATA
L N 3 I2S_Bit_CLK 1 BRIGHTNESS
4 I2S_System_MCLK 2 ON/OFF
5 AUDIO_SW 3
6 VOLUME 4
1 2 3
7 MUTE 5
8 6 +19V
9 7
10 ON/OFF 8
P801
11 BRIGHTNESS
AC_SKT 8P 2.0mm
12
13 VCC 5V
14

14P 2.0mm

VX2250W-1
ViewSonic Corporation 84 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 CON12PIN

R840
NC CN804
R808
33K 1 VCC

2 NC
R806
R841 33K C810 3
NC 0.1/50V GND

4 NC

2
Q804 5
AP2761I FB
1
6 NC
6 D813
R843 4148

3
R842 8 5 10 R803 7
VCC

NC HV OUT 10K D
R844 R813
1M 20 8
IC802 NC
7 NC 3
PO268 CS
R809 9
470 CS
GND

1 SD FB 2
10 NC
4

R845 C842 11
100K 220p/50V C811 C809 NC
220p/50V 220p/50V
12 HV

VX2250W-1
ViewSonic Corporation 85 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 9. PCB Layout Diagrams

VX2250W-1
ViewSonic Corporation 86 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 87 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 88 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250W-1
ViewSonic Corporation 89 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 10. Exploded Diagram And Spare Parts List

VX2250W-LED

VX2250W-1
ViewSonic Corporation 90 CONFIDENTIAL – DO NOT COPY VX2250WM-1
ViewSonic Confidential Creation Date:

EXPLODED PARTS LIST (VX2250w-LED-1)

ViewSonic Model Number: VS13239
Rev: 1a
Item ViewSonic P/N Ref. P/N Description Q'ty
1 #N/A 50118P21A800R DECORATION,LP21A8 1
2 #N/A 75003P21A801R SUB-ASSY,POWER BUTTON,LP21A8 1
3 #N/A 75003P21A800R SUB-ASSY,POWER BUTTON RING,LP21A8 1
4 #N/A 501110601000R LOGO THREE BRIDS 7.9MM LE2082 1
5 #N/A 75001P21A800R SUB-ASSY,BEZEL,BLACK,W/SPK,LP21A8 1
6 E-00010089 631102221621H LCP 21.5"MT215DW01-V1-G1,AM2150001101(IN 1
7 #N/A 795361300600R PCBA,IF/B(V1,W/SPK),LP21A8-622 ROHS 1
8 B-00010259 795360500600R PCBA,LED CON/B,LP21A8-622 ROHS 1
9 #N/A 795361400600R PCBA,PI/B,W/SPK,LP21A8-622 ROHS 1
10 #N/A 509146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc 8
11 #N/A 70106P21A800R ASSY,CHASSIS,DUAL,W/O SPK ,INL,LP21A8 1
12 #N/A 618100200790R Speaker 2.5W 4Ω 50&70mm R/B/G W/CASE 0
13 #N/A 502020100700R LOCK SHEET,LP2259 1
14 #N/A 509412610500R SCREW,B,CROSS,T.T-4*10,BLK ,ROHS 2
15 #N/A 509416608500R SCREW,B,CROSS,M4*8,BLK 2
16 #N/A 50102P21A800R BACK COVER,DUAL,W/O SPK ,BLACK,INL,LP21A 1
17 #N/A 502090105600R VESA,LE23W2 4
18 #N/A 503020006300R RUBBER FOOT L14.8*W9.6*T3.5mm ,LE19E3 5
19 #N/A 509012306800R SCREW,M4*9,Zn (WITH MANUAL),LP2479 1
20 #N/A 50124P21A800R BASE,LP21A8 1
21 #N/A 506120303000R BAG EPE+PE W330xL300xT0.3mm CYCLE PRINTE 1
22 #N/A 509412608500R SCREW,B,CROSS,T.T-4*8,BLK ROHS 2
23 #N/A 71411P21A800R ASSY,HINGE,LP21A8 1
24 #N/A 50126P21A800R STAND,LP21A8 1
25 #N/A 50202P21A801R BRACKET,STAND,INL,LP21A8 1
26 #N/A 509212606110R SCREW,F,CROSS,T4*6,Zn,ROHS(5.8~6.2) 2
27 B-00010257 795361500600R PCBA,KEYPAD/B,LP21A8-622 ROHS 1
28 B-00010258 795361500601R PCBA,FUNTION KEY/B,LP21A8-622 ROHS 1

VX2250W-1
ViewSonic Corporation 91 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 VX2250WM-LED

VX2250W-1
ViewSonic Corporation 92 CONFIDENTIAL – DO NOT COPY VX2250WM-1
ViewSonic Confidential Creation Date:

EXPLODED PARTS LIST (VX2250wm-LED-1)

ViewSonic Model Number: VS13239
Rev: 1a
Item ViewSonic P/N Ref. P/N Description Q'ty
1 NA 50118P21A800R DECORATION,LP21A8 1
2 NA 75003P21A801R SUB-ASSY,POWER BUTTON,LP21A8 1
3 NA 75003P21A800R SUB-ASSY,POWER BUTTON RING,LP21A8 1
4 NA 501110601000R LOGO THREE BRIDS 7.9MM LE2082 1
5 NA 75001P21A800R SUB-ASSY,BEZEL,BLACK,W/SPK,LP21A8 1
6 E-00010089 631102221621H LCP 21.5"MT215DW01-V1-G1,AM2150001101(IN 1
7 B-00010260 795361300600R PCBA,IF/B(V1,W/SPK),LP21A8-622 ROHS 1
8 B-00010259 795360500600R PCBA,LED CON/B,LP21A8-622 ROHS 1
9 B-00010261 795361400600R PCBA,PI/B,W/SPK,LP21A8-622 ROHS 1
10 NA 509146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc 8
11 NA 70106P21A801R ASSY,CHASSIS,DUAL,W/SPK ,INL,LP21A8 1
12 E-00010090 618100200790R Speaker 2.5W 4Ω 50&70mm R/B/G W/CASE 1
13 NA 502020100700R LOCK SHEET,LP2259 1
14 NA 509412610500R SCREW,B,CROSS,T.T-4*10,BLK ,ROHS 2
15 NA 509416608500R SCREW,B,CROSS,M4*8,BLK 2
16 NA 50102P21A801R BACK COVER,DUAL,W/SPK ,BLACK,INL,LP21A8 1
17 NA 502090105600R VESA,LE23W2 4
18 NA 503020006300R RUBBER FOOT L14.8*W9.6*T3.5mm ,LE19E3 5
19 NA 509012306800R SCREW,M4*9,Zn (WITH MANUAL),LP2479 1
20 NA 50124P21A800R BASE,LP21A8 1
21 NA 506120303000R BAG EPE+PE W330xL300xT0.3mm CYCLE PRINTE 1
22 NA 509412608500R SCREW,B,CROSS,T.T-4*8,BLK ROHS 2
23 NA 71411P21A800R ASSY,HINGE,LP21A8 1
24 NA 50126P21A800R STAND,LP21A8 1
25 NA 50202P21A801R BRACKET,STAND,INL,LP21A8 1
26 NA 509212606110R SCREW,F,CROSS,T4*6,Zn,ROHS(5.8~6.2) 2
27 B-00010257 795361500600R PCBA,KEYPAD/B,LP21A8-622 ROHS 1
28 B-00010258 795361500601R PCBA,FUNTION KEY/B,LP21A8-622 ROHS 1

VX2250W-1
ViewSonic Corporation 93 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 PPL(VX2250w-LED-1)

VX2250W-1
ViewSonic Corporation 94 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 PACKING PART LIST (VX2250w-LED-1)
ViewSonic Model Number: VS13239
Rev: 1a
Item ViewSonic P/N Ref. P/N Description Q'ty
1 P-00010238 50613P21A800R CUSHION,L-VX2250w-LP21A8 1
2 CB-00008190 453030300370R CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS 1
3 CB-00008437 453010100380R CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH 1
4 P-00008419 506120300430R BAG EPE+PO L590xW530xT0.6mm(PRINTED)LE22 1
5 NA 703010002206R KIT ASSY CN VX2250wm-LP21A8 1
6 A-00005255 453070800170R PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx 1
7 P-00010239 50613P21A802R CUSHION,MIDDLE-VX2250w-LP21A8 1
8 PL-00008851 71402P21A800R ASSY,BASE,LP21A8 1
9 NA 506120305400R BAG, EPE-HDPE, L300*W220,LE17A0 1
10 NA 506431007900R FILM PROTECTION 500*290*0.1mm,VA2213WM 1
11 NA 50602P21A801R CARTON,VX2250wm-LP21A8 1
12 NA 506440004800R LABEL,BLANK,86.2x76.2mm,,CARTON,LE1709 1

VX2250W-1
ViewSonic Corporation 95 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 PPL(VX2250wm-LED-1)

VX2250W-1
ViewSonic Corporation 96 CONFIDENTIAL – DO NOT COPY VX2250WM-1

14
 PACKING PART LIST (VX2250wm-LED-1)
ViewSonic Model Number: VS13239
Rev: 1a
Item ViewSonic P/N Ref. P/N Description Q'ty
1 P-00010238 50613P21A800R ASSY,BASE,LP21A8 1
2 CB-00008190 453030300370R CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS 1
3 CB-00008437 453010100380R CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH 1
4 P-00008419 506120300430R BAG EPE+PO L590xW530xT0.6mm(PRINTED)LE22 1
5 DC-00010332 703010002206R KIT ASSY CN VX2250wm-LP21A8 1
6 A-00005255 453070800170R PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx 1
7 NA 453030300120R CABLE AUDIO 1P 6FT BLACK/GREEN CP03B06P0 1
8 P-00010239 50613P21A802R CUSHION,MIDDLE-VX2250w-LP21A8 1
9 PL-00008851 71402P21A800R ASSY,BASE,LP21A8 1
10 NA 506120305400R BAG, EPE-HDPE, L300*W220,LE17A0 1
11 NA 506431007900R FILM PROTECTION 500*290*0.1mm,VA2213WM 1
12 P-00010240 50602P21A801R CARTON,VX2250wm-LP21A8 1
13 NA 506440004800R LABEL,BLANK,86.2x76.2mm,,CARTON,LE1709 1

VX2250W-1
ViewSonic Corporation 97 CONFIDENTIAL – DO NOT COPY VX2250WM-1
11. Recommended Spare Parts List

RECOMMENDED SPARE PARTS LIST (VX2250w-LED-1)

ViewSonic Model Number: VS13239
Rev: 1a
Serial No. Prefix: RWT
Item Category Part Name Description ECR/ECN ViewSonic P/N Ref. P/N Ref. NO Compatibility Location Universal number# Remark
1 Accessories: [Adapter, Power Cord PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx(USA) A-00008111 453070800150R Main Source
Remote Controller,
2 Power Cord PWRCORD 7A/125V BLK 6FT CNS VCTF 3Gx0.75 (TWN) A-00006733 453070800480R Main Source
Power Cord, External
3 Cables] Power Cord PWR CORD 16A/250V BLK 6FT VDE,H05VV-F 3G (Europe) A-00008279 453070801190R Main Source
4 Power Cord PWRCORD 10A/250V BLACK 6FT SAA,H05W-F/3G(Australia) A-00003671 453070800420R Main Source
5 Power Cord PWRCORD 16A/250V BLK 6FT KTL,H05VV-F 3Gx (Korea) A-00006734 453070800500R Main Source
6 Power Cord PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx0. (China) A-00005255 453070800170R Main Source
7 Power Cord PWRCORD 5A/250V BLK 6FT UK3Gx.75mm(SP60/ (Singapore) A-00003675 453070800230R Main Source
8 Signal Cable CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH CB-00008437 453010100380R Main Source
9 Signal Cable CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS CB-00008190 453030300370R Main Source
10 PC Board Assembly: Main Board PCBA,IF/B(V1,W/O SPK),LP21A8-622 ROHS B-00010255 795361300601R Main Source
[All boards or PCBA] B-00010256
11 Power Board PCBA,PI/B,W/O SPK,LP21A8-622 ROHS 795361400601R Main Source
12 Key Pad PCBA,KEYPAD/B,LP21A8-622 ROHS B-00010257 795361500600R Main Source
13 Key Pad PCBA,FUNTION KEY/B,LP21A8-622 ROHS B-00010258 795361500601R Main Source
14 LED Board PCBA,LED CON/B,LP21A8-622 ROHS B-00010259 795360500600R Main Source
15 Cabinets: [Front Bezel, Front Bezel ASSY, BEZEL,BLACK,W/SPK,LP21A8 C-00010186 71403P21A800R Main Source
All Covers, Base/Stand C-00010187
16 Back Cover ASSY,BACK COVER,DUAL,W/O SPK ,BLACK,INL, 71405P21A800R Main Source
Assembly]
17 Stand Assembly ASSY,STAND,LP21A8 C-00010188 71401P21A800R Main Source
18 Cables: [All internal Flat Cable HRN LVDS FFC 30P 171mm W/CORE CB-00009403 430303003890R Main Source
Cables/wires] CB-00009404
19 Wire HRN ASS'Y 2x4P to 8P 80mm UL1571#28 Cond 430300804130R Main Source
20 Wire HRN ASS'Y 2*5P to 2*5P 80mm UL1571#28 W/ CB-00009405 430301001580R Main Source
21 Documentation: [Quick Manual Set KIT ASSY CN VX2250w-LP21A8 DC-00010331 703010002106R Main Source
St t G id CD R E-00010089
22 Electronic Components: Panel LCP 21.5"MT215DW01-V1-G1,AM2150001101(IN 631102221621H Main Source
[LCD P l S k
23 Packing Material: Carton CARTON,VX2250w-LP21A8 P-00010237 50602P21A800R Main Source
[Carton, Box, Foam,
24 Cushion CUSHION,L-VX2250w-LP21A8 P-00010238 50613P21A800R Main Source
Bags]
25 Cushion CUSHION,MIDDLE-VX2250w-LP21A8 P-00010239 50613P21A802R Main Source
26 Plastic Bag BAG EPE+PO L590xW530xT0.6mm(PRINTED)LE22 P-00008419 506120300430R Main Source
27 Plastic Bag BAG,PLASTIC,L660xW(580+140)xT0.05mm,LE22 P-00008713 506120008500R Main Source
28 Plastics: [Pedestal, Pedestal ASSY,BASE,LP21A8 PL-00008851 71402P21A800R Main Source
t d/ k Pl t
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each
Notice: 1. For some special parts, some photos for identification purpose may be asked by request
2. For all internal cables, there must be some wordings on the "Description" column about where the cable is used (connecting to which two parts)
3. All internal cables/wires should be put in the "Cables" category
4. All external cables should be put in the "Accessories" category
5. Parts relationship (Main/Second source or 1/2/3/4) should be added in the "Compatibility" column
6. If any part for certain product isn't listed in the form, supplier/PE can add it themselves and keep the part name unified.

VX2250W-1
ViewSonic Corporation 98 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 RECOMMENDED SPARE PARTS LIST (VX2250wm-LED-1)
ViewSonic Model Number: VS13239
Rev: 1a
Serial No. Prefix: RWS
Item Category Part Name Description ECR/ECN ViewSonic P/N Ref. P/N Ref. NO Compatibility Location Universal number# Remark
1 Accessories: [Adapter, Power Cord PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx(USA) A-00008111 453070800150R Main Source
Remote Controller,
2 Power Cord PWRCORD 7A/125V BLK 6FT CNS VCTF 3Gx0.75 (TWN) A-00006733 453070800480R Main Source
Power Cord, External
3 Cables] Power Cord PWR CORD 16A/250V BLK 6FT VDE,H05VV-F 3G (Europe) A-00008279 453070801190R Main Source
4 Power Cord PWRCORD 10A/250V BLACK 6FT SAA,H05W-F/3G(Australia) A-00003671 453070800420R Main Source
5 Power Cord PWRCORD 16A/250V BLK 6FT KTL,H05VV-F 3Gx (Korea) A-00006734 453070800500R Main Source
6 Power Cord PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx0. (China) A-00005255 453070800170R Main Source
7 Power Cord PWRCORD 5A/250V BLK 6FT UK3Gx.75mm(SP60/ (Singapore) A-00003675 453070800230R Main Source
8 Signal Cable CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH CB-00008437 453010100380R Main Source
9 Signal Cable CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS CB-00008190 453030300370R Main Source
10 PC Board Assembly: Main Board PCBA,IF/B(V1,W/SPK),LP21A8-622 ROHS B-00010260 795361300600R Main Source
[All boards or PCBA] B-00010261
11 Power Board PCBA,PI/B,W/SPK,LP21A8-622 ROHS 795361400600R Main Source
12 Key Pad PCBA,KEYPAD/B,LP21A8-622 ROHS B-00010257 795361500600R Main Source
13 Key Pad PCBA,FUNTION KEY/B,LP21A8-622 ROHS B-00010258 795361500601R Main Source
14 LED Board PCBA,LED CON/B,LP21A8-622 ROHS B-00010259 795360500600R Main Source
15 Cabinets: [Front Front Bezel ASSY, BEZEL,BLACK,W/SPK,LP21A8 C-00010186 71403P21A800R Main Source
Bezel, All Covers, C-00010189
16 Back Cover ASSY,BACK COVER,DUAL,W/SPK ,BLACK,INL,LP 71405P21A801R Main Source
Base/Stand Assembly]
17 Stand Assembly ASSY,STAND,LP21A8 C-00010188 71401P21A800R Main Source
18 Cables: [All internal Flat Cable HRN LVDS FFC 30P 171mm W/CORE CB-00009403 430303003890R Main Source
Cables/wires]
19 Wire HRN ASS'Y 2x4P to 8P 80mm UL1571#28 Cond CB-00009404 430300804130R Main Source
20 Wire HRN ASS'Y 2*5P to 2*5P 80mm UL1571#28 W/ CB-00009405 430301001580R Main Source
21 Documentation: Manual Set KIT ASSY CN VX2250wm-LP21A8 DC-00010332 703010002206R Main Source
[Q i k St t G id
22 Electronic Panel LCP 21.5"MT215DW01-V1-G1,AM2150001101(IN E-00010089 631102221621H Main Source
Components: [LCD
23 Panel, Speaker, and all Speaker Speaker 2.5W 4Ω 50&70mm R/B/G W/CASE E-00010090 618100200790R Main Source
24 Packing Material: Carton CARTON,VX2250wm-LP21A8 P-00010240 50602P21A801R Main Source
[Carton, Box, Foam,
25 Cushion CUSHION,L-VX2250w-LP21A8 P-00010238 50613P21A800R Main Source
Bags]
26 Cushion CUSHION,MIDDLE-VX2250w-LP21A8 P-00010239 50613P21A802R Main Source
27 Plastic Bag BAG EPE+PO L590xW530xT0.6mm(PRINTED)LE22 P-00008419 506120300430R Main Source
28 Plastic Bag BAG,PLASTIC,L660xW(580+140)xT0.05mm,LE22 P-00008713 506120008500R Main Source
Plastics: [Pedestal,
29 Pedestal ASSY,BASE,LP21A8 PL-00008851 71402P21A800R Main Source
stand/neck Plate

Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item
Notice: 1. For some special parts, some photos for identification purpose may be asked by request
2. For all internal cables, there must be some wordings on the "Description" column about where the cable is used (connecting to which two parts)
3. All internal cables/wires should be put in the "Cables" category
4. All external cables should be put in the "Accessories" category
5. Parts relationship (Main/Second source or 1/2/3/4) should be added in the "Compatibility" column
6. If any part for certain product isn't listed in the form, supplier/PE can add it themselves and keep the part name unified.

VX2250W-1
ViewSonic Corporation 99 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 BOM LIST (VX2250w-LED-1)
ViewSonic Model Number: VS13239
Rev: 1a
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty Unit
1 A-00005255 453070800170R PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx 100 PC
2 CB-00008190 453030300370R CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS 100 PC
3 CB-00008437 453010100380R CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH 100 PC
4 NA 71300P21A805R ASSY,PACKAGE,PACK,VSCN,VX2250w-LP21A8 100 PC
5 P-00010238 50613P21A800R CUSHION,L-VX2250w-LP21A8 200 PC
6 P-00010239 50613P21A802R CUSHION,MIDDLE-VX2250w-LP21A8 100 PC
7 NA 506431007900R FILM PROTECTION 500*290*0.1mm,VA2213WM 100 PC
8 P-00008713 506120008500R BAG,PLASTIC,L660xW(580+140)xT0.05mm,LE22 100 PC
9 P-00008419 506120300430R BAG EPE+PO L590xW530xT0.6mm(PRINTED)LE22 100 PC
10 P-00010237 50602P21A800R CARTON,VX2250w-LP21A8 101 PC
11 NA 50642P21A800R LBL RATING,VX2250w-LP21A8 100 PC
12 NA 506440004800R LABEL,BLANK,86.2x76.2mm,,CARTON,LE1709 100 PC
13 NA 506440002400R LABEL,BLANK,50x25mm,LE1709(S/N) 100 PC
14 NA 506440002600R LABEL,BLANK,210x65mm,LE1709(PALLET) 3.57 PC
15 NA 506091000700R LABEL,CHINA STICKER CARD,VIEWSONIC, LP22 100 PC
16 NA 506390000500R LABEL,QC-PASS, LE1709 100 PC
17 NA 50645P21A801R LABEL POP FEATURE ,VX2250w-LP21A8 100 PC
18 NA 50649P214000R LABEL,Φ8mm,Non-ZBD, LP2140 20 PC
19 NA 50647P21A800R CHINA ENERGY LABEL VX2250wm-w-LP21A8 100 PC
20 NA 506092001400R CARD WARRANTY LE1709 100 PC
21 DC-00010331 703010002106R KIT ASSY CN VX2250w-LP21A8 100 PC
22 NA 50653P21A800R MNL USER'S(CD) ,VX2250wm-w-LP21A8 100 PC
23 NA 50652P21A801R QSG ,CN-VX2250w-LP21A8 100 PC
24 NA 506420405200R INSERT SHEET, 1920*1080,LE21N1 100 PC
25 NA 506380001800R TAPE,WRAPPING TYPE,48mmx50M 1.6 ROL
26 NA 506250017820R LABEL ADDRESS,For CARTON ,VX2240 ,LP2297 100 PC
27 NA 71301P21A800R ASSY,PACK,SEA,40STD,WW,VX2250wm-LP21A8 100 PC
28 NA 506150002621R PALLET,L1150xW990xH120mm,LE19B0 1.79 PC
29 NA 5060390104B0R Corner Paper 1950x40x40x40xT5mm 7.14 PC
30 NA 506039000100R CORNER PAPER 1000x50x50xT5mm 3.57 PC
31 NA 506039005400R CORNER PAPER 800x50x50xT5mm LE1512 3.57 PC
32 NA 506038002520R CARDBOARD L1138x961xt5mm LE2262 1.79 PC
33 NA 506038006800R CARDBOARD,L1080xW910xT3 LE1798 1.79 PC
34 NA 506431000300R FILM,PE 500mmx900M ROHS 0.3 ROL
35 NA 506380002100R TAPE WRAPPING TYPE(VIEWSONIC) 50mmx75M L 0.63 ROL
36 NA 506120100500R SEALED BAG ADHESIVE 330x230mm LE1918 1.79 PC
37 NA 71407P21A800R ASSY,FINAL(B,V1-110)W/O SPK,LP21A8-622/V 100 PC
38 C-00010187 71405P21A800R ASSY,BACK COVER,DUAL,W/O SPK ,BLACK,INL, 100 PC
39 NA 50102P21A800R BACK COVER,DUAL,W/O SPK ,BLACK,INL,LP21A 100 PC
40 NA 502020100700R LOCK SHEET,LP2259 100 PC
41 NA 502090105600R VESA,LE23W2 400 PC
42 C-00010186 71403P21A800R ASSY, BEZEL,BLACK,W/SPK,LP21A8 100 PC
43 NA 75001P21A800R SUB-ASSY,BEZEL,BLACK,W/SPK,LP21A8 100 PC
44 NA 50101P21A800R BEZEL,BLACK,LP21A8 100 PC
45 NA 75003P21A800R SUB-ASSY,POWER BUTTON RING,LP21A8 100 PC
46 NA 50119P21A800R POWER BUTTON RING,LP21A8 100 PC

VX2250W-1
ViewSonic Corporation 100 CONFIDENTIAL – DO NOT COPY VX2250WM-1
47 NA 75003P21A801R SUB-ASSY,POWER BUTTON,LP21A8 100 PC
48 NA 50103P21A800R POWER BUTTON,LP21A8 100 PC
49 NA 50118P21A800R DECORATION,LP21A8 100 PC
50 NA 501110601000R LOGO THREE BRIDS 7.9MM LE2082 100 PC
51 C-00010188 71401P21A800R ASSY,STAND,LP21A8 100 PC
52 NA 50126P21A800R STAND,LP21A8 100 PC
53 NA 50202P21A801R BRACKET,STAND,INL,LP21A8 100 PC
54 NA 509212606110R SCREW,F,CROSS,T4*6,Zn,ROHS(5.8~6.2) 200 PC
55 NA 509412608500R SCREW,B,CROSS,T.T-4*8,BLK ROHS 200 PC
56 NA 71411P21A800R ASSY,HINGE,LP21A8 100 PC
57 PL-00008851 71402P21A800R ASSY,BASE,LP21A8 100 PC
58 NA 50124P21A800R BASE,LP21A8 100 PC
59 NA 509012306800R SCREW,M4*9,Zn (WITH MANUAL),LP2479 100 PC
60 NA 503020006300R RUBBER FOOT L14.8*W9.6*T3.5mm ,LE19E3 500 PC
61 NA 506120305400R BAG, EPE-HDPE, L300*W220,LE17A0 100 PC
62 NA 509412608500R SCREW,B,CROSS,T.T-4*8,BLK ROHS 200 PC
63 NA 509416608500R SCREW,B,CROSS,M4*8,BLK 200 PC
64 NA 71408P21A800R ASSY,PANEL(V1-110)W/O SPK,LP21A8-622/VX2 100 PC
65 NA 70106P21A800R ASSY,CHASSIS,DUAL,W/O SPK ,INL,LP21A8 100 PC
66 NA 50209P21A800R CHASSIS,DUAL,W/O SPK ,INL,LP21A8 100 PC
67 NA 50202P21A800R BRACKET,HINGE,INL,LP21A8 100 PC
68 NA 51103P21A800R INSULATOR,MYLAR,17x13xT0.3mm,LP21A8 100 PC
69 NA 51103P21A801R INSULATOR,MYLAR,25x14xT0.3mm,LP21A8 400 PC
70 NA 509000000700R BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RO 400 PC
71 NA 509146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc 800 PC
72 NA 506381000700R TAPE,ACE,45mmx30M(PC=10x45mm) 400 PC
73 B-00010255 795361300601R PCBA,IF/B(V1,W/O SPK),LP21A8-622 ROHS 100 PC
74 B-00010256 795361400601R PCBA,PI/B,W/O SPK,LP21A8-622 ROHS 100 PC
75 B-00010257 795361500600R PCBA,KEYPAD/B,LP21A8-622 ROHS 100 PC
76 B-00010258 795361500601R PCBA,FUNTION KEY/B,LP21A8-622 ROHS 100 PC
77 B-00010259 795360500600R PCBA,LED CON/B,LP21A8-622 ROHS 100 PC
78 E-00010089 631102221621H LCP 21.5"MT215DW01-V1-G1,AM2150001101(IN 100 PC
79 CB-00009403 430303003890R HRN LVDS FFC 30P 171mm W/CORE 100 PC
80 NA 430301001830R HRN FFC 10P 445mm TOP 100 PC
81 NA 430301001840R HRN FFC 10P 569mm DOWN 100 PC
82 CB-00009404 430300804130R HRN ASS'Y 2x4P to 8P 80mm UL1571#28 Cond 100 PC
83 NA 430300600650R HRN ASS'Y 5P to 6P 122mm UL1571#28 Condu 100 PC
84 CB-00009405 430301001580R HRN ASS'Y 2*5P to 2*5P 80mm UL1571#28 W/ 100 PC
85 NA 51115E23DF00R FOIL,AL.,DOUBLE COND,L35*W20*T0.07,HP S2 100 PC
86 NA 511150101800R FOIL,AL.,DOUBLE COND.,60x35xT0.07mm, LE2 100 PC
87 NA 51103P21A802R INSULATOR,MYLAR,100x100xT0.3mm,LP21A8 100 PC

VX2250W-1
ViewSonic Corporation 101 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 BOM LIST (VX2250wm-LED-1)
ViewSonic Model Number: VS13239
Rev: 1a
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty Unit
1 A-00005255 453070800170R PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx 100 PC
2 CB-00008190 453030300370R CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS 100 PC
3 NA 453030300120R CABLE AUDIO 1P 6FT BLACK/GREEN CP03B06P0 100 PC
4 CB-00008437 453010100380R CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH 100 PC
5 NA 71300P21A811R ASSY,PACKAGE,PACK,VSCN,VX2250wm-LP21A8 100 PC
6 P-00010238 50613P21A800R CUSHION,L-VX2250w-LP21A8 200 PC
7 NA 506380001800R TAPE,WRAPPING TYPE,48mmx50M 1.6 PC
8 P-00010239 50613P21A802R CUSHION,MIDDLE-VX2250w-LP21A8 100 PC
9 NA 506431007900R FILM PROTECTION 500*290*0.1mm,VA2213WM 100 PC
10 P-00008713 506120008500R BAG,PLASTIC,L660xW(580+140)xT0.05mm,LE22 100 PC
11 P-00008419 506120300430R BAG EPE+PO L590xW530xT0.6mm(PRINTED)LE22 100 PC
12 P-00010240 50602P21A801R CARTON,VX2250wm-LP21A8 101 PC
13 NA 50642P21A801R LBL RATING,VX2250wm-LP21A8 100 PC
14 NA 506440004800R LABEL,BLANK,86.2x76.2mm,,CARTON,LE1709 100 PC
15 NA 506440002400R LABEL,BLANK,50x25mm,LE1709(S/N) 100 PC
16 NA 506440002600R LABEL,BLANK,210x65mm,LE1709(PALLET) 3.57 PC
17 NA 506091000700R LABEL,CHINA STICKER CARD,VIEWSONIC, LP22 100 PC
18 NA 506390000500R LABEL,QC-PASS, LE1709 100 PC
19 NA 50645P21A800R LABEL POP FEATURE ,VX2250wm-LP21A8 100 PC
20 NA 50649P214000R LABEL,Φ8mm,Non-ZBD, LP2140 20 PC
21 NA 50647P21A800R CHINA ENERGY LABEL VX2250wm-w-LP21A8 100 PC
22 NA 506092001400R CARD WARRANTY LE1709 100 PC
23 DC-00010332 703010002206R KIT ASSY CN VX2250wm-LP21A8 100 PC
24 NA 50653P21A800R MNL USER'S(CD) ,VX2250wm-w-LP21A8 100 PC
25 NA 50652P21A803R QSG ,CN-VX2250wm-LP21A8 100 PC
26 NA 506420405200R INSERT SHEET, 1920*1080,LE21N1 100 PC
27 NA 506250017820R LABEL ADDRESS,For CARTON ,VX2240 ,LP2297 100 PC
28 NA 71301P21A800R ASSY,PACK,SEA,40STD,WW,VX2250wm-LP21A8 100 PC
29 NA 506150002621R PALLET,L1150xW990xH120mm,LE19B0 1.79 PC
30 NA 5060390104B0R Corner Paper 1950x40x40x40xT5mm 7.14 PC
31 NA 506039000100R CORNER PAPER 1000x50x50xT5mm 3.57 PC
32 NA 506039005400R CORNER PAPER 800x50x50xT5mm LE1512 3.57 PC
33 NA 506038002520R CARDBOARD L1138x961xt5mm LE2262 1.79 PC
34 NA 506038006800R CARDBOARD,L1080xW910xT3 LE1798 1.79 PC
35 NA 506431000300R FILM,PE 500mmx900M ROHS 0.3 ROL
36 NA 506380002100R TAPE WRAPPING TYPE(VIEWSONIC) 50mmx75M L 0.63 ROL
37 NA 506120100500R SEALED BAG ADHESIVE 330x230mm LE1918 1.79 PC
38 NA 71407P21A801R ASSY,FINAL(B,V1-110)W/SPK,LP21A8-622/VX2 100 PC
39 C-00010189 71405P21A801R ASSY,BACK COVER,DUAL,W/SPK ,BLACK,INL,LP 100 PC
40 NA 50102P21A801R BACK COVER,DUAL,W/SPK ,BLACK,INL,LP21A8 100 PC
41 NA 502020100700R LOCK SHEET,LP2259 100 PC
42 NA 502090105600R VESA,LE23W2 400 PC
43 C-00010186 71403P21A800R ASSY, BEZEL,BLACK,W/SPK,LP21A8 100 PC
44 NA 75001P21A800R SUB-ASSY,BEZEL,BLACK,W/SPK,LP21A8 100 PC
45 NA 50101P21A800R BEZEL,BLACK,LP21A8 100 PC
46 NA 75003P21A800R SUB-ASSY,POWER BUTTON RING,LP21A8 100 PC
47 NA 50119P21A800R POWER BUTTON RING,LP21A8 100 PC
48 NA 75003P21A801R SUB-ASSY,POWER BUTTON,LP21A8 100 PC
49 NA 50103P21A800R POWER BUTTON,LP21A8 100 PC
50 NA 50118P21A800R DECORATION,LP21A8 100 PC
51 NA 501110601000R LOGO THREE BRIDS 7.9MM LE2082 100 PC
52 C-00010188 71401P21A800R ASSY,STAND,LP21A8 100 PC
53 NA 50126P21A800R STAND,LP21A8 100 PC
54 NA 50202P21A801R BRACKET,STAND,INL,LP21A8 100 PC
55 NA 509212606110R SCREW,F,CROSS,T4*6,Zn,ROHS(5.8~6.2) 200 PC
56 NA 509412608500R SCREW,B,CROSS,T.T-4*8,BLK ROHS 200 PC
57 NA 71411P21A800R ASSY,HINGE,LP21A8 100 PC
58 PL-00008851 71402P21A800R ASSY,BASE,LP21A8 100 PC
59 NA 50124P21A800R BASE,LP21A8 100 PC
60 NA 509012306800R SCREW,M4*9,Zn (WITH MANUAL),LP2479 100 PC
61 NA 503020006300R RUBBER FOOT L14.8*W9.6*T3.5mm ,LE19E3 500 PC
62 NA 506120305400R BAG, EPE-HDPE, L300*W220,LE17A0 100 PC
63 NA 509412608500R SCREW,B,CROSS,T.T-4*8,BLK ROHS 200 PC
64 NA 509416608500R SCREW,B,CROSS,M4*8,BLK 200 PC

VX2250W-1
ViewSonic Corporation 102 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 65 NA 71408P21A801R ASSY,PANEL(V1-110)W/SPK,LP21A8-622/VX225 100 PC
66 NA 70106P21A801R ASSY,CHASSIS,DUAL,W/SPK ,INL,LP21A8 100 PC
67 NA 50209P21A801R CHASSIS,DUAL,W/SPK INL,LP21A8 100 PC
68 NA 50202P21A800R BRACKET,HINGE,INL,LP21A8 100 PC
69 NA 51103P21A800R INSULATOR,MYLAR,17x13xT0.3mm,LP21A8 100 PC
70 NA 51103P21A801R INSULATOR,MYLAR,25x14xT0.3mm,LP21A8 400 PC
71 NA 51103P21A802R INSULATOR,MYLAR,100x100xT0.3mm,LP21A8 100 PC
72 NA 509000000700R BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RO 400 PC
73 NA 509146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc 800 PC
74 NA 506381000700R TAPE,ACE,45mmx30M(PC=10x45mm) 400 PC
75 B-00010260 795361300600R PCBA,IF/B(V1,W/SPK),LP21A8-622 ROHS 100 PC
76 B-00010261 795361400600R PCBA,PI/B,W/SPK,LP21A8-622 ROHS 100 PC
77 B-00010257 795361500600R PCBA,KEYPAD/B,LP21A8-622 ROHS 100 PC
78 B-00010258 795361500601R PCBA,FUNTION KEY/B,LP21A8-622 ROHS 100 PC
79 B-00010259 795360500600R PCBA,LED CON/B,LP21A8-622 ROHS 100 PC
80 E-00010089 631102221621H LCP 21.5"MT215DW01-V1-G1,AM2150001101(IN 100 PC
81 CB-00009403 430303003890R HRN LVDS FFC 30P 171mm W/CORE 100 PC
82 CB-00009404 430300804130R HRN ASS'Y 2x4P to 8P 80mm UL1571#28 Cond 100 PC
83 NA 430300600650R HRN ASS'Y 5P to 6P 122mm UL1571#28 Condu 100 PC
84 CB-00009405 430301001580R HRN ASS'Y 2*5P to 2*5P 80mm UL1571#28 W/ 100 PC
85 NA 430301001830R HRN FFC 10P 445mm TOP 100 PC
86 NA 430301001840R HRN FFC 10P 569mm DOWN 100 PC
87 NA 511150101800R FOIL,AL.,DOUBLE COND.,60x35xT0.07mm, LE2 100 PC
88 NA 51115E23DF00R FOIL,AL.,DOUBLE COND,L35*W20*T0.07,HP S2 100 PC
89 E-00010090 618100200790R Speaker 2.5W 4Ω 50&70mm R/B/G W/CASE 100 PC
90 NA 51103P21A802R INSULATOR,MYLAR,100x100xT0.3mm,LP21A8 100 PC

VX2250W-1
ViewSonic Corporation 103 CONFIDENTIAL – DO NOT COPY VX2250WM-1
 * Reader’s Response*
Dear Readers:

Thank you in advance for your feedback on our Service Manual, which allows continuous
improvement of our products. We would appreciate your completion of the Assessment Matrix
below, for return to ViewSonic Corporation.
Assessment
A. What do you think about the content of this Service Manual?
Unit Excellent Good Fair Bad
1. Precautions and Safety Notices

2. Specification

3. Front Panel Function Control Description

4. Circuit Description

5. Adjustment Procedure

6. Troubleshooting Flow Chart

7. Block Diagrams

8. Schematic Diagrams

9.PCB Layout Diagrams

10. Exploded Diagram and Exploded Parts List

11. Recommended Spare Parts List

B. Are you satisfied with this Service Manual?

Item Excellent Good Fair Bad
1. Service Manual Content
2. Service Manual Layout
3. The form and listing

C. Do you have any other opinions or suggestions regarding this service manual?

Reader’s basic dada:

Name: Title:
Company:
Add:
Tel: Fax:
E-mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at
facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality
Systems & Processes ([email protected])

VX2250W-1
ViewSonic Corporation 104 CONFIDENTIAL – DO NOT COPY VX2250WM-1