Al p h a 6 0 0 S e r i e s

Industrial Radio Remote Control System

Operation & Parts Manual

Fomotech International Corp.

Downloaded from www.Manualslib.com manuals search engine

 TABLE OF CONTENTS
Page
1. SAFETY INSTRUCTION ............................................................................................. 3
2. PUSHBUTTON CONFIGURATION
2.1 Alpha 604 Models ............. ..................................................................................... 4
2.2 Alpha 607 & 608 Models ....................................................................................... 5
2.3 Alpha 612 Models ................................................................................................... 5
3. TRANSMITTER OUTLINE
3.1 Transmitter Outline ................................................................................................. 6
3.2 Alpha 604/607/608/612 Spare Parts ....................................................................... 7
3.3 Battery Charger .................................................................................................... 7
4. RECEIVER OUTLINE
4.1 Alpha 604-608 ........................................................................................................... 8
4.1.1 Alpha 604-608 Models External Assembly .......................................................... 8
4.1.2 Alpha 604 Models Internal Assembly ................................................................... 9
4.1.3 Alpha 607/607 Models Internal Assembly ............................................................ 10
4.2 Alpha 612 ................................................................................................................... 11
4.2.1 Alpha 612 Models External Assembly .................................................................. 11
4.2.2 Alpha 612 Models External/Internal Assembly ..................................................... 12
4.3 α604/α608/α612 Receiver Power Fuse List ......................................................... 13
5. OUTPUT CONTACT DIAGRAMS
5.1 Alpha 604 Models ............. ..................................................................................... 14
5.2 Alpha 607 Models ................................................................................................. 14
5.3 Alpha 608 Models ................................................................................................. 15
5.4 Alpha 612 Models ................................................................................................. 17
6. SYSTEM CONFIGURATIONS
6.1 How to Set ID Codes ............................................................................................. 22
6.2 Transmitter RF Channel Setting ............................................................................. 22
7. RECEIVER SETTING
7.1 How to Set Receiver ID Codes ................................................................................ 22
7.2 Receiver RF Channel Settings ................................................................................. 23
7.3 Receiver Function Settings ...................................................................................... 24
7.3.1 α604/607/608 Receiver Function Settings ......................................................... 24
7.3.2 α612 Receiver Function Settings ........................................................................ 25
7.3.3 α612 Models Dip-Switch Function Table ....................................................... 26
7.3.4 α612 Receiver Voltage Settings ......................................................................... 28
7.4 Frequency (RF) Channels Table .............................................................................. 29
8. TRANSMITTER OPERATION & STATUS LIGHT
8.1 Transmitter Operating Steps .................................................................................... 31
8.2 Transmitter Status light ............. .............................................................................. 32
9. RECEIVER INSTALLATION
9.1 Preparation For Installation ................................................................................... 33
9.2 Step-By-Step Installation ....................................................................................... 33
9.3 System Testing ....................................................................................................... 35
9.4 Receiver System Status LED Display..................................................................... 35

-1-

Downloaded from www.Manualslib.com manuals search engine

 10. BATTERY CHARGER
10.1 Charger Operation ................................................................................................. 37
10.2 Battery Charger LED Status Light ......................................................................... 39
11. TROUBLE SHOOTING................................................................................................. 39
12. SYSTEM SPECIFICATION ........................................................................................ 40
13. PARTS LIST ................................................................................................................. 42

Downloaded from www.Manualslib.com manuals search engine

 1. S AFETY INS TRUCTIO N

The Alpha 600 series are relatively simple to use, however, it is very important to observe the proper
safety procedures before, during, and after operation. When used properly, the Alpha 600 series will
enhance safety, productivity and efficiency in the workplace.

The following procedures should be strictly followed:

1. The transmitter is equipped with a specialized battery charger. Only two ”AA” Ni-MH rechargeable
batteries are allowed to be used in the transmitter. Please note the polarity of the batteries. Do not
use other types of battery to prevent any accident.
2. Be sure to replace the batteries with the same brand and specification at the same time. Do not
replace only one battery in the battery compartment otherwise the charging (discharging) performance
may be affected by the battery with lower voltage.
3. Do not place the battery charger under the raining, high temperature, humid and with corroded air
environment. Indoor with good ventilation is suggested. Please also do not use the battery
charger under 0℃.
4. It is prohibited that the high power wireless equipment such as walkie-talkie, wireless network
transmitter, … etc. is closed to the transmitter or receiver as it might cause interference.
5. Do not change the IDs on transmitter encoder and receiver decoder boards at will.
6. Check the transmitter casing and pushbuttons daily. Should any damage that could inhibit the
proper operation of the transmitter be found the unit should be immediately removed from service.
7. Check the transmitter voltage whenever it is operated. Place the transmitter into battery charger
when battery is running out or the voltage is low.
8. The red emergency stop button (EMS) should be checked at the beginning of each shift to ensure it is
in proper working order and the “Stop” command is being received by the receiver.
9. In the event of an emergency press down the EMS button will immediately deactivates the receiver
MAIN relay and the transmitter power. Then turned the power “off ” from the main power source to
the crane or equipment.
10. Do not use the same RF channel and ID code as any other system in use at the same facility or within
300-meter distance.
11. Ensure the waist belt is worn at all time during operation to avoid accidental damage to the
transmitter.
12. Rotate the power switch to OFF position when the transmitter is not operated temporarily or the
operation is finished.
13. Any repair or adjustment should be proceeding by repair technician for radio remote controls.
14. The operator should not change any electrical parts at will.

Downloaded from www.Manualslib.com manuals search engine

 2. PUS H BUTTO N CO NFIG URATIO N
2.1 Alpha 604 Models

1. Alpha 604A -- (4) single speed pushbuttons

2. Alpha 604B -- (4) double speed pushbuttons

POWER STOP POWER STOP

(Alpha 604A) (Alpha 604B)

Below are some of many types of pushbutton configurations that are also available, please contact your dealer
for more details.

Interlocked (Can also be set to non-interlocked via an external programmer unit).

-4-

Downloaded from www.Manualslib.com manuals search engine

 2.2 Alpha 607 & 608 Models

1. Alpha 607A -- (7) single speed pushbuttons

2. Alpha 607B -- (6) double speed pushbuttons + (1) single speed pushbuttons
3. Alpha 607AT -- (6) single speed pushbuttons + (1) SELECT I/II pushbutton
4. Alpha 607BT -- (6) double speed pushbuttons + (1) SELECT I/II pushbutton
5. Alpha 608A -- (8) single speed pushbuttons
6. Alpha 608B -- (6) double speed pushbuttons + (2) single speed pushbuttons
7. Alpha 608AT -- (7) single speed pushbuttons + (1) SELECT I/II pushbutton
8. Alpha 608BT -- (6) double speed pushbuttons + (1) single speed pushbuttons+ (1) SELECT I/II pushbutton

POWER STOP POWER STOP

(Alpha 607A) (Alpha 607B) (Alpha 607AT) (Alpha 607BT) (Alpha 608A) (Alpha 608B) (Alpha 608AT) (Alpha 608BT)

2.3 Alpha 612 Models

1. Alpha 612A → (12) one-speed pushbuttons
2. Alpha 612B → (11) one-speed pushbuttons + I/II select pushbutton*
3. Alpha 612C-1 → (6) two- speed + (6) one-speed pushbuttons
4. Alpha 612C-2 → (8) two-speed + (4) one-speed pushbuttons
5. Alpha 612D → (10) two-speed + (2) one-speed pushbuttons
6. Alpha 612E-1 → (6) two-speed + (5) one-speed pushbuttons + I/II select pushbutton*
7. Alpha 612E-2 → (8) two-speed + (3) one-speed pushbuttons + I/II select pushbutton*
* For cranes with auxiliary hoist and trolley (changeover function).

POWER STOP POWER STOP POWER STOP

POWER STOP POWER STOP

Alpha 612A Alpha 612B Alpha 612C-1 Alpha 612E-1 Alpha 612 button
Alpha 612C-2 Alpha 612E-2 reference
Alpha 612D
-5-

Downloaded from www.Manualslib.com manuals search engine

 3. TRANS MITTER O UTLINE
3.1 Transmitter Outline
(Alpha 604) (Alpha 607/608) (Alpha 612)

(Fig.1) Transmitter Front View

(Fig.2) Transmitter encoder board and induction charging board

(Fig.3) Transmitter Internal Assembly:

(1) Internal antenna

(2) Status LED display
(3) Battery contact
(4) Transmitter induction charging port
(5) Programming port
(6) Function dip-switch
(7) JP2 setting pin
(8) JP1 setting pin

-6-

Downloaded from www.Manualslib.com manuals search engine

 3.2 Alpha 604/607/608/612 Spare Parts

(1) Charging cable

(2) Charger (optional)
(3) Transmitter shock-absorbing rubber
(4) Shoulder strap
(5) Rechargeable batteries (optional)

3.3 Battery Charger

1 2

(1) Charger power status: green light

(2) Charging status: green/red light
(3-1) Power input socket AC100-240V 3-1

(3-2) Power input socket DC12-24V

(4) Charger holder (optional). Please refer to 4
below figure for the installation holes.

3-2

(Fig.4) Battery Charger

& Holder
-7-

Downloaded from www.Manualslib.com manuals search engine

 4. RECEIVER O UTLINE
4.1 Alpha 604 ~ 608
4.1.1 Alpha 604 ~ 608 Models External Assembly
SIZE：310mm X 134mm X 72mm

1
EN ISO 13849-1:2008, PLd

60947 EMS

2
1 U1
HOIST 2 NC

F2 5A
3
4
D1
NC
3
U
5 COM1 D
TROLLEY
6 E1 E
7 W1 W
F3 5A 8 NC N
9 COM2 S
10 N1 A A
BRIDGE
11 S1
M M
SQ SQ
F4 5A 12 NC
AC AC
13 COM3
LV/AUX1 14 LV
/AUX2
15 AUX1
F5 5A 16 AUX2
17 COM4
MAIN
F6 18 MAIN
5A
19 COM5
F1 FF1
20 L1(X1) 10
FILTER

POWER
21 L2(X2)
22 GRN/YEL
Anti-vibration spring
must be grounded

4 7
MOD: I D:

5 CH : F REQ: 8 11
VOLT: S/ N :
6 9

(Fig.5) Front View (Fig.6) Back View

1) Receiver enclosure 5) System frequency 9) Supplied voltage

2) Wiring diagram 6) System serial number 10) Anti-vibration spring
3) Receiver LED displays* 7) System ID code 11) Grounding (GND)
4) Type model 8) System RF channel

* A ~ AUX Relay Contact Indicator (for Alpha 607A /608B models only).
* M ~ MAIN and 2nd Speed Relay Contact Indicator.
Green "on" → MAIN activated (All models).
Red "on" → 2nd speed activated (for Alpha 608B model only).
* SQ ~ RF Signal Indicator (Red).
"on" → RF signal detected and received.
"off" → No RF signal detected or received.
Blinking at transmitter power "off" → Other radio interference.
* AC ~ Power Source Indicator (red) "on" → AC input power supplied.
"off" → No AC input power.

-8-

Downloaded from www.Manualslib.com manuals search engine

 4.1.2 Alpha 604 Internal Assembly

(Fig. 7) Internal Parts Assembly

1) Receiving RF module
2) Power module *
3) Secondary power AC fuse (F1)
5
4) Primary power AC fuse (FF1)
5) System status LED display* 1 6

6) External antenna port 7

7) ID code dip-switch 8
8) RF channel dip-switch
9) Contact relay LED display 9
10) Pushbutton #1 and #2 fuse (5.0A)
11) MAIN fuse (5.0A)
FU

2
SE
10

12 Contact output seat (CN3) FU

SE
11
13) Low-voltage (LV) fuse (5.0A)
3
14) Contact output seat (CN4)

SE
FU
15) Pushbutton #3 and #4 fuse (5.0A)
12
16) AC power input seat (CN2) FU
SE
13
17) Cable gland & output cable
14
FU
SE

15
16
* Power module: Including transformer or 4
full-voltage module.
* Please refer to 4.3 α604/α608/α612 Receiver
Power Fuse List.

*Please refer to page 36 for system status

LED display information.

17

2 1) Spare fuse & jumper compartment

3
2) Spare Jumper slots
3) Spare fuse slots
4 4) Receiver top casing

-9-

Downloaded from www.Manualslib.com manuals search engine

 4.1.3 Alpha 608 Internal Assembly

(Fig. 8) Internal Parts Assembly

1) Receiving RF module
2) External programming port
3) Power module
8
4) Secondary power AC fuse (F1)
5) Contact output seat (CN8) 9
6) Primary power AC fuse (FF1) 1 10
7) AC power input seat (CN2) 2 11
8) Internal Antenna
12
9) System Status LED display*
10 )External antenna port 13
11) ID code dip-switch
12) RF channel dip-switch 3 FU
SE
14
13) Contact relay LED display
14) Pushbutton #1and #2 fuse (5.0A)

SE
FU
15) Contact output seat (CN3) 4
FU
SE
15
16) MAIN contact fuse (5.0A) 5 16
17) Pushbutton #3 and #4 fuse (5.0A) FU
SE
17
18) Pushbutton #5 and #6 fuse (5.0A) FU
SE

18
19) Contact output seat (CN4)
20) LV & AUX fuse (5.0A)
19
21) Cable gland & output cable 6
SE
FU

20
7
* Power module: Including transformer or
full-voltage module.
* Please refer to 4.3 α604/α608/α612
Receiver Power Fuse List.

*Please refer to page 36 for system status

LED display information.
21

- 10 -

Downloaded from www.Manualslib.com manuals search engine

 4.2 Alpha 612

4.2.1 Alpha 612 External Asse mbly

SIZE：300mm X 230mm X 86mm

(Fig. 9) External Parts Assembly

1) Transparent top cover 3) Mounting bracket with shock absorbers

2) Light-gray colored base 4) Cable gland / Cord grip

- 11 -

Downloaded from www.Manualslib.com manuals search engine

 4.2.2 Alpha 612 Internal Assembly

1 13
2 14
3 15
4 16
5
17
6
7
18
8
19
9 20
10
11

12

(Fig. 10) Internal Parts Assembly

1) Power LED display* 12) Pushbutton #1 and #2 relay fuse (5.0A)

2) SQ LED display** 13) Receiving RF module or PLL (Phase Lock Loop)
3) Status LED display**** 14) External antenna port
4) DC power relay LED display*** 15) RF channel dip-switch
5) Programming port 16) ID code dip-switch
6) Jumper settings 17) Secondary power fuse (0.8A) (except for AC48V)
7) Function dip-switch 18) Voltage selector seat
8) Pushbutton #3 and #4 relay fuse (5.0A) 19) MAIN relay fuse (5.0A)
9) Pushbutton #5 and #6 relay fuse (5.0A) 20) Pushbutton A4 relay fuse (5.0A)
10) Pushbutton A1and A2 relay fuse (5.0A) 21) Primary power fuse (1.0A) (AC110V up only)
11) Pushbutton A3 relay fuse (5.0A) 22) Low-voltage (LV) relay fuse (5.0A)

* POWER ~ AC Power Source Indicator "on" → AC input power supplied.

"off" → No AC input power.
** SQ ~ RF Signal Indicator "on" → RF signal detected and received.
"off" → No RF signal detected or received.
Blinking at transmitter power “off” → Other radio interference.
*** RELAY_COM ~ DC Power Source to Relays "on" → DC power to relays.
"off" → No DC power to relays.
**** STATUS ~ Receiver System Status LED Display → Please refer to page 36.

- 12 -

Downloaded from www.Manualslib.com manuals search engine

 4.3 α 604/α 608/α 612 Receiver Power Fuse List

Voltage
Type Parts No. AC100~120 AC220~240 AC380~440 AC100~240V
DC12V~24V AC24 AC36~48V V V V Full-Voltage

α604 FF1 3A 1A 2A
α608 F1 3A 2A 0.5A 1A
FF1 3A 1A
α612
F1 3A 2A 0.8A

- 13 -

Downloaded from www.Manualslib.com manuals search engine

 5. O UTPUT CO NTACT DIAG RAMS
5.1 Alpha 604 Models
(Alpha 604A) (Alpha 604B)

MAIN MAIN
5A 5A

U/D U/D
5A 5A

PB2 PB1
E/W E/W
5A 5A

LV LV PB4 PB3
5A 5A

FOM TECH

POWER POWER

5.2 Alpha 607 Models

(Alpha 607A) (Alpha 607B)

1 U1 1 U1
HOIST 2 NC HOIST 2 U2
F2 5A
3 D1 3 D1
F2 5A 4 NC 4 D2
5 COM1 5 COM1

TROLLEY
6 E1 TROLLEY
F3 5A
6 E1 PB2 PB1
7 W1 7 W1
F3 5A 8 NC 8 E/W2
9 COM2 9 COM2
PB4 PB3
10 N1 BRIDGE 10 N1
BRIDGE F4 5A
11 S1 11 S1
F4 5A 12 NC 12 N/S2
13 COM3 13 COM3 PB6 PB5
LV/AUX1 14 LV LV/AUX1 14 LV
15 AUX1 15 AUX1
F5 5A 16 NC F5 5A 16 NC PB8 PB7
17 COM4 17 COM4
MAIN MAIN
F6 18 MAIN F6 18 MAIN
5A 5A
19 COM5 19 COM5
F1 FF1 F1 FF1
FILTER

20 L1(X1)
FILTER

20 L1(X1)
POWER POWER
FOM TECH
21 L2(X2) 21 L2(X2)
22 GRN/YEL 22 GRN/YEL
Anti-vibration spring Anti-vibration spring
must be grounded must be grounded

- 14 -

Downloaded from www.Manualslib.com manuals search engine

 (Alpha 607AT) (Alpha 607BT)

1 U1 1 U1
HOIST 2 NC HOIST 2 U2
F2 5A
3 D1 3 D1
F2 5A 4 NC 4 D2
5 COM1 5 COM1
6 E1 TROLLEY 6 E1
TROLLEY F3 5A
7 W1 7 W1
F3 5A 8 NC 8 E/W2
9 COM2 9 COM2
10 N1 BRIDGE 10 N1
BRIDGE F4 5A
11 S1 11 S1
F4 5A 12 NC 12 N/S2
13 COM3 13 COM3
LV/SEL-I 14 LV LV/SEL-I 14 LV
/SEL-II /SEL-II
15 SEL-I 15 SEL-I
F5 5A 16 SEL-II F5 5A 16 SEL-II
17 COM4 17 COM4
MAIN MAIN
F6 18 MAIN F6 18 MAIN
5A 5A
19 COM5 19 COM5
F1 FF1 F1 FF1

FILTER
FILTER

20 L1(X1) 20 L1(X1)
POWER POWER PB2 PB1
21 L2(X2) 21 L2(X2)
22 GRN/YEL 22 GRN/YEL
Anti-vibration spring Anti-vibration spring
must be grounded must be grounded PB4 PB3

5.3 Alpha 608 Models PB6 PB5

(Alpha 608A) (Alpha 608B)
PB8 PB7
1 U1 1 U1
HOIST 2 NC HOIST 2 U2
F2 5A
3 D1 3 D1
F2 5A 4 NC 4 D2
FOM TECH
5 COM1 5 COM1
6 E1 TROLLEY 6 E1
TROLLEY
7 W1 F3 5A
7 W1
F3 5A 8 NC 8 E/W2
9 COM2 9 COM2
10 N1 BRIDGE 10 N1
BRIDGE
11 S1 F4 5A
11 S1
F4 5A 12 NC 12 N/S2
13 COM3 13 COM3
LV/AUX1 14 LV LV/AUX1
/AUX2 14 LV
/AUX2
15 AUX1 15 AUX1
F5 5A 16 AUX2 F5 5A 16 AUX2
17 COM4 17 COM4
MAIN MAIN
F6 18 MAIN 18 MAIN
F6
5A 5A
19 COM5 19 COM5
F1 FF1 F1 FF1
FILTER

20 L1(X1)
FILTER

POWER 20 L1(X1)
POWER
21 L2(X2) 21 L2(X2)
22 GRN/YEL 22 GRN/YEL
Anti-vibration spring Anti-vibration spring
must be grounded must be grounded

- 15 -

Downloaded from www.Manualslib.com manuals search engine

 (Alpha 608AT) (Alpha 608BT)

1 U1 1 U1
HOIST 2 NC HOIST 2 U2
F2 5A
3 D1 3 D1
POWER STOP
F2 5A 4 NC 4 D2
5 COM1 5 COM1
6 E1 TROLLEY 6 E1 PB2 PB1
TROLLEY F3 5A
7 W1 7 W1
F3 5A 8 NC 8 E/W2
9 COM2 9 COM2 PB4 PB3
10 N1 BRIDGE 10 N1
BRIDGE F4 5A
11 S1 11 S1
F4 5A 12 NC 12 N/S2 PB6 PB5
13 COM3 13 COM3
SEL-II/AUX1 14 SEL-II SEL-II/AUX1 14 SEL-II
/SEL-I /SEL-I
15 AUX1 15 AUX1
PB8 PB7
F5 5A 16 SEL-I F5 5A 16 SEL-I
17 COM4 17 COM4
MAIN MAIN
F6 18 MAIN F6 18 MAIN
5A 5A
19 COM5 19 COM5
F1 FF1 F1 FF1
FILTER

20 L1(X1)
FILTER

POWER 20 L1(X1)
POWER
21 L2(X2) 21 L2(X2)
22 GRN/YEL 22 GRN/YEL
Anti-vibration spring Anti-vibration spring
must be grounded must be grounded

- 16 -

Downloaded from www.Manualslib.com manuals search engine

 5.4 Alpha 612 Models

(Alpha 612A)

PB2 PB1

PB4 PB3

PB6 PB5

PB8 PB7

PB9

FOM TECH

(Alpha 612B)

POWER STOP

- 17 -

Downloaded from www.Manualslib.com manuals search engine

 (Alpha 612C-1)

PB2 PB1

PB4 PB3

PB6 PB5

PB8 PB7

PB9

FOM TECH

(Alpha612C-2)

PB2 PB1

PB4 PB3

PB6 PB5

PB8 PB7

PB9

FOM TECH

- 18 -

Downloaded from www.Manualslib.com manuals search engine

 (Alpha 612D)

PB2 PB1

PB4 PB3

PB6 PB5

PB8 PB7

PB9

FOM TECH

(Alpha 612E-1)

POWER STOP

- 19 -

Downloaded from www.Manualslib.com manuals search engine

 (Alpha 612E-2)

POWER STOP

- 20 -

Downloaded from www.Manualslib.com manuals search engine

 6. TRANS MITTER S ETTING S
6.1 How to Set ID Codes

6.1.1 Set by programming tool

6.1.2 Set by encoder board JP1, 1st / 2nd pin and dip-switch

Setting Steps:

(1) Rotate the transmitter power to OFF position

(2) Remove the transmitter shock-absorbing rubber
(3) Place the transmitter pushbutton side downward and unscrew the transmitter bottom casing.
(4) Set the transmitter ID code with the dip-switch on the encoder board and put jumper on the 1st and
2nd pin of JP1.
(5) Make sure the batteries are installed properly.
(6) Rotate the transmitter power switch to ON position.
(7) Green status LED ON for 0.1 sec, OFF for 0.1 sec, flash for 1 sec. (5 times)
(8) Green status LED steady ON indicates the setting is completed. If the LED status light is changed to
red, the setting is failed. Please repeat the above setting steps until the setting is successful.
(9) After setting is completed and successful, remove short boot from the 1 st and 2nd pin of JP1.
(10) Rotate transmitter power switch to OFF position.

編碼板

(Fig. 11) Back view (Fig. 12) Position of dip-switch & jumpers

Top slot ON  “1”; bottom slot  “0”. The setting above is 00000011.

- 21 -

Downloaded from www.Manualslib.com manuals search engine

 6.2 Transmitter Channel Settings

Transmitter channel settings (Select the channel you would like to operate. Do not exceed
the channel limit)

6.2.1 Set by programming tool

6.2.2 Set by encoder board 2nd & 3rd pin of JP1 and dip-switch

To set the frequency on JP1 of TX board, put jumper on 2nd & 3rd pin of JP1. Set the frequency needed
by changing the dip-switch setting. Repeat the previous steps to set another frequency.

Example：Set channel as 03→(00000011) → Correct setting

7. RECEIVER S ETTING S
7.1 How to set α604/607/608/612 Receiver ID Codes

7.1.1 How to set α604/607/608 Receiver ID Codes

Top slot  “1”

Bottom slot  “0”

ID DIP-SW

Set the ID codes needed with the dip-switch on the decoder board. For example: the ID codes set above
 10000111.

- 22 -

Downloaded from www.Manualslib.com manuals search engine

 7.1.2 How to set α612 Receiver ID Codes

Please refer to Fig. 18 Internal Parts Assembly (Page 11) for 8-position ID code dip-switch to set receiver ID
code.

Top slot “1”; bottom slot “0”

Set the ID codes needed on the decoder board dip-switch.

For example: the ID codes → 10010110
（“1” value adds up must to be “4”）

1 2 3 4 5 6 7 8

7.2 Receiver RF Channel Settings

There are 68 sets of user-adjustable receiving RF channels that can be set manually via an 8-position
dip-switch located to the right of the receiving RF module. Change the receiving RF channel simply by
resetting the 8-position dip-switch. For the location of the receiving RF module, please refer to fig. 7, 8, and
10 on page 9, 10, and 12.
1
2
3
4
5
6
7
8

Top slot “1”; bottom slot “0”

For example：the channel dip-switch set above  00101, channel 05.

- 23 -

Downloaded from www.Manualslib.com manuals search engine

 7.3 Receiver Function Settings
7.3.1 α604/607/608 Receiver Function Settings
7.3.1.1 Set by programming tool
7.3.1.2. Adjust Jumper setting function by decoder board

Adjusting jumper setting to change function selection (refer to Jump Set table as below):

JP1 => α607A/B/608: MODE 0: Start the system either by AUX pushbutton (No.7 pushbutton) or
power switch.
MODE 1: JP1 setting is invalid. Start the system by power switch.
α604/607T: Start the system by power switch.

JP2 => Mode 0: Set the MAIN relay auto shutdown time as 5 minutes or base on customer’s single
request. The auto shutdown time is set either by the manufacturer or distributor
within setting range 0~30 minutes. (default 5 minutes)

Mode 1: JP2 setting is invalid. The MAIN relay auto shutdown time is controlled by the
transmitter.
JP3 => 1. Refer to “JP3 (*1)“ of Jumper Set Table on Page 24 & 25, for α604A/B, 607A/AT/B/BT, 608A/B
2. Refer to”JP3(*2), α608T only” on Page 25, for α608AT/BT.

Receiver function settings:

A. The MAIN relay will be activated when system is started. (After the receiver power is started and
emergency stop button is elevated)
B. The MAIN relay auto shutdown time can be set as 5 minutes or depends on customer’s single request.
(Remark 1)
C. When transmitter voltage is low, relays for the receiver MAIN and LV (Remark 1) will be auto shutdown
after one minute.

JP1 DIP-SW
JP2 OPEN→JUMP
JP3
JP4 U

SHORT→JUMP

AC
FU
SE

(Fig. 13) Alpha 607, 608 models

Jumper Set table: in-plant setting (default).

Transmitter AUX pushbutton start (when MAIN
JP1 Open relay is off)
(Mode 0)
Short Transmitter power switch start (when MAIN off is off)
Open No auto shutdown time on Main relay
JP2
(Mode 0) The receiver MAIN will be deactivated after consecutive
Short
5 minutes of standby time.
When the transmitter voltage is low, LV relay
JP3(*1) Open
activates/deactivates every second.

- 24 -

Downloaded from www.Manualslib.com manuals search engine

 * 4 pushbuttons: When either relay of pushbutton 1~4 is
activated, LV relay will also be activated.
* 8 pushbuttons: When either relay of pushbutton 1~6 is
Short
activated, LV relay will also be activated.
* 12 pushbuttons: When either relay of pushbutton 1~8 is
activated, LV relay will also be activated.
JP3(*2) Open MAIN relay off, I & II relays remain unchanged
α608T only Short MAIN relay off, I & II relay off.
Open 7th AUX: “Normal” pushbutton setting
JP4
Short 7th AUX: “Toggle” pushbutton setting

“Start” means: MAIN relay unlatches and then latches.

※ Open → no Jumper Short → put Jumper
Remark 1：The setting of auto shutdown time can be done by manufacturer or distributor. Setting range:
0~30 minutes. (In-plant setting: 5 minutes)
Remark 2：When the transmitter voltage is low, LV relay will be activated and siren or lights will be ON.
(One second of interval)
Remark 3：Every time when you change jumper settings you must first turn the receiver power off and then
turn it back on so that the new settings can be stored in memory.

7.3.2 α612 Receiver Function Settings

7.3.2.1 Set by programming tool
7.3.2.2. Adjust Jumper setting function by decoder board

Receiver funct ion settings:

Jumper Set table: In-plant setting (default).
Transmitter 11th pushbutton (AUX) start (when
Open
JP1 MAIN relay is off)
(Mode 0) Transmitter power switch start (when MAIN relay is
Short
off)
Open No auto shutdown time on Main relay
JP2
The receiver MAIN will be deactivated after
(Mode 0) Short
consecutive 5 minutes of standby time.
When the transmitter voltage is low, LV relay
Open
activates/deactivates every second.
JP3
When either relay of pushbutton 1~8 is activated, LV
Short
relay will also be activated.

“Start” means: MAIN relay unlatches and then latches.

Mode 1: 1. JP1 setting is invalid. The system is startup by power switch start.
2. JP2 setting is invalid. The MAIN relay auto shutdown time is set by the transmitter.

※ Open → No jumper Short → Put Jumper

Remark 1：The setting of auto shutdown time can be done by manufacturer or distributor. Setting range:
0~30 minutes. (In-plant setting: 5 minutes)

※ Prior to Jumper setting, be sure to first switch off the system to set.

※ Please take out the batteries from the battery compartment when the transmitter is not operated for a
longer time, otherwise the batteries may leak and cause malfunction to the transmitter.
- 25 -

Downloaded from www.Manualslib.com manuals search engine

 7.3.3 Alpha 612 Models Dip-Switch Function Table

Model Pushbutton Dip-Switch Setting Description

1&2 → 1 Not Interlocked

3&4 DIP 1
5&6 → 0 Interlocked

→ 1 Not Interlocked
7&8 DIP 2
→ 0 Interlocked
612A
→ 1 Latching/toggle relay contact
7&8 DIP 3 DIP2 Set at “1”
→ 0 Momentary relay contact

→ 1 Not Interlocked
9 & 10 DIP 4
→ 0 Interlocked

→ 1 Latching/toggle relay contact

9 DIP 5 DIP4 Set at “1”
→ 0 Momentary relay contact
612B
→ 1 Latching/toggle relay contact
10 DIP 6 DIP4 Set at “1”
→ 0 Momentary relay contact

→ 1 Not Interlocked
7&8 DIP 1
→ 0 Interlocked

→ 1 Latching/toggle relay contact

7 DIP 2
→ 0 Momentary relay contact DIP4 Set at “1”
612B
→ 1 Latching/toggle relay contact
8 DIP 3 DIP4 Set at “1”
→ 0 Momentary relay contact

→ 1 Latching/toggle relay contact

9 DIP 4
→ 0 Momentary relay contact
Both 1st and 2nd speed contact
Both 1st and 2nd speed
→ 1 relay interlocked when pressed
contact relays activated
1&2 to 2nd speed
612C DIP 1
(2nd speed) Both 1st and 2nd speed contact
Only 2nd speed contact
→ 0 relay activated when pressed to
relay activated
2nd speed

- 26 -

Downloaded from www.Manualslib.com manuals search engine

 DIP 2,3 → 00 Momentary relay contact

9 DIP 2,3 → 01 Latching/toggle relay contact

DIP 2,3 → 10 Activate the 3rd speed

→ 1 Latching/toggle relay contact

10 DIP 4
→ 0 Momentary relay contact

Both 1st and 2nd speed contact

Both 1st and 2nd speed
→ 1 relay interlocked when pressed
contact relays activated
1&2 to 2nd speed
DIP 1
(2nd speed) Both 1st and 2nd speed contact
Only 2nd speed contact
612D → 0 relay activated when pressed to
relay activated
2nd speed
DIP2&3 Must set to
--- DIP 2,3,4 →0 Momentary relay contact “0” all the time
(In-plant set at “0”)
Both 1st and 2nd speed contact
Both 1st and 2nd speed
→ 1 relay interlocked when pressed
contact relays activated
1&2 to 2nd speed
DIP 1
(2nd speed) Both 1st and 2nd speed contact
Only 2nd speed contact
→ 0 relay activated when pressed to
relay activated
2nd speed
612E → 1 Not Interlocked
7&8 DIP 2
→ 0 Interlocked

→ 1 Latching/toggle relay contact

7 DIP 3 DIP2 Set at “1”
→ 0 Momentary relay contact

→ 1 Latching/toggle relay contact

11 DIP 7
→ 0 Momentary relay contact
612
A/B/C/D/E
→ 1 Latching/toggle relay contact
12 DIP 8
→ 0 Momentary relay contact

※ In-plant all set at “0”

- 27 -

Downloaded from www.Manualslib.com manuals search engine

 7.3.4 Alpha 612 Receiver Voltage Settings

1. Select the voltage of the place where the receiver is installed.

2. Select the position of the “Y” terminal base on the label marked on the transformer.
If the default voltage setting is different from the place where the receiver is installed, please

change the setting base on below steps:

2.1 Please first refer to below figure. Keep the “COM” end of the wire in
the position as it is, remove the “Y” terminal from the other end of the wire,
then screw the position originally with “Y” terminal tightly.
2.2 Select the voltage needed base on the label of the transformer. Unscrew the
position selected, put the “Y” terminal into the position selected and screw it
tightly.

Transformer type no.： K-2367

․Position ③ AC 110V → AC 100V ~ AC 125V
․Position ④ AC 240V → AC 200V ~ AC 240V

Transformer type no.： K-2368

․Position ⑤ AC 380V → AC 350V ~ AC 380V
․Position ⑥ AC 460V → AC 400V ~ AC 460V

Transformer type no.： SSB-2665

․Position ③ AC 25 V
․Position ④ AC 36 V
․Position ⑤ AC 42 V
․Position ⑥ AC 50 V

3. Please make sure that the wire and the 5 screws are securely screwed.

- 28 -

Downloaded from www.Manualslib.com manuals search engine

 7.4 Frequency (RF) Channels Table

Band 301MHz Dip-Switch Setting Channel Band 301MHz Dip-Switch Setting Channel
301.105 MHz 00000001 01 301.955 MHz 00100011 35
301.130 MHz 00000010 02 301.980 MHz 00100100 36
301.155 MHz 00000011 03 302.005 MHz 00100101 37
301.180 MHz 00000100 04 302.030 MHz 00100110 38
301.205 MHz 00000101 05 302.055 MHz 00100111 39
301.230 MHz 00000110 06 302.080 MHz 00101000 40
301.255 MHz 00000111 07 302.105 MHz 00101001 41
301.280 MHz 00001000 08 302.130 MHz 00101010 42
301.305 MHz 00001001 09 302.155 MHz 00101011 43
301.330 MHz 00001010 10 302.180 MHz 00101100 44
301.355 MHz 00001011 11 302.205 MHz 00101101 45
301.380 MHz 00001100 12 302.230 MHz 00101110 46
301.405 MHz 00001101 13 302.255 MHz 00101111 47
301.430 MHz 00001110 14 302.280 MHz 00110000 48
301.455 MHz 00001111 15 302.305 MHz 00110001 49
301.480 MHz 00010000 16 302.330 MHz 00110010 50
301.505 MHz 00010001 17 302.355 MHz 00110011 51
301.530 MHz 00010010 18 302.380 MHz 00110100 52
301.555 MHz 00010011 19 302.405 MHz 00110101 53
301.580 MHz 00010100 20 302.430 MHz 00110110 54
301.605 MHz 00010101 21 302.455 MHz 00110111 55
301.630 MHz 00010110 22 302.480 MHz 00111000 56
301.655 MHz 00010111 23 302.505 MHz 00111001 57
301.680 MHz 00011000 24 302.530 MHz 00111010 58
301.705 MHz 00011001 25 302.555 MHz 00111011 59
301.730 MHz 00011010 26 302.580 MHz 00111100 60
301.755 MHz 00011011 27 302.605 MHz 00111101 61
301.780 MHz 00011100 28 302.630 MHz 00111110 62
301.805 MHz 00011101 29 302.655 MHz 00111111 63
301.830 MHz 00011110 30 302.680 MHz 01000000 64
301.855 MHz 00011111 31 302.705 MHz 01000001 65
301.880 MHz 00100000 32 302.730 MHz 01000010 66
301.905 MHz 00100001 33 302.755 MHz 01000011 67
301.930 MHz 00100010 34 302.780 MHz 01000100 68
NOTE!!! It is prohibited to use Channel 221 and 255.

- 29 -

Downloaded from www.Manualslib.com manuals search engine

 Band 433MHz Dip-Switch Setting Channel Band 433MHz Dip-Switch Setting Channel
433.075 MHz 00000001 01 434.425 MHz 00100011 35
433.100 MHz 00000010 02 434.450 MHz 00100100 36
433.125 MHz 00000011 03 434.475 MHz 00100101 37
433.150 MHz 00000100 04 434.500 MHz 00100110 38
433.175 MHz 00000101 05 434.525 MHz 00100111 39
433.200 MHz 00000110 06 434.550 MHz 00101000 40
433.225 MHz 00000111 07 434.575 MHz 00101001 41
433.250 MHz 00001000 08 434.600 MHz 00101010 42
433.275 MHz 00001001 09 434.625 MHz 00101011 43
433.300 MHz 00001010 10 434.650 MHz 00101100 44
433.825 MHz 00001011 11 434.675 MHz 00101101 45
433.850 MHz 00001100 12 434.700 MHz 00101110 46
433.875 MHz 00001101 13 434.725 MHz 00101111 47
433.900 MHz 00001110 14 434.750 MHz 00110000 48
433.925 MHz 00001111 15 434.775 MHz 00110001 49
433.950 MHz 00010000 16 433.325 MHz 00110010 50
433.975 MHz 00010001 17 433.350 MHz 00110011 51
434.000 MHz 00010010 18 433.375 MHz 00110100 52
434.025 MHz 00010011 19 433.400 MHz 00110101 53
434.050 MHz 00010100 20 433.425 MHz 00110110 54
434.075 MHz 00010101 21 433.450 MHz 00110111 55
434.100 MHz 00010110 22 433.475 MHz 00111000 56
434.125 MHz 00010111 23 433.500 MHz 00111001 57
434.150 MHz 00011000 24 433.525 MHz 00111010 58
434.175 MHz 00011001 25 433.550 MHz 00111011 59
434.200 MHz 00011010 26 433.575 MHz 00111100 60
434.225 MHz 00011011 27 433.600 MHz 00111101 61
434.250 MHz 00011100 28 433.625 MHz 00111110 62
434.275 MHz 00011101 29 433.650 MHz 00111111 63
434.300 MHz 00011110 30 433.675 MHz 01000000 64
434.325 MHz 00011111 31 433.700 MHz 01000001 65
434.350 MHz 00100000 32 433.725 MHz 01000010 66
434.375 MHz 00100001 33 433.750 MHz 01000011 67
434.400 MHz 00100010 34 433.775 MHz 01000100 68

- 30 -

Downloaded from www.Manualslib.com manuals search engine

 8. TRANS MITTER O PERATIO N & STATUS
LIG H T

8.1 Transmitter Operating Steps

1. Make sure the two “AA” NiMH rechargeable batteries are installed correctly. Please note the polarity
of the batteries.
2. Status lights _To operate the transmitter, please rotate the power key on the top-left corner clockwise
to “on” position. The status LED (green and red) will be steady “on” for 2 seconds and then “off”. If
the transmitter Status LED displays a red blinking light that is “on”  0.1 second and “off”  1.9
seconds, or no light at all, this indicates the transmitter with batteries needs to be recharged. For battery
charging or replacement, please refer to instruction next page.
3. When any function pushbutton is depressed, the transmitter Status LED displays a red blinking light
that is “on” 0.1 second and “off” 1.9 seconds. If the voltage is low, the transmitter Status LED
will be “on”0.1 second and “off”1.9 seconds, this indicates the transmitter with batteries needs to
be recharged. Continuous operation will cause the transmitter battery power exhausting and cannot
operate at all.
4. EMS & Restarting _ In case of an emergency, press down the red emergency stop button (EMS) will
immediately deactivates the transmitter and receiver MAIN relay. (do not rotate the power switch to
OFF first)

Shutting Off the Transmitter(POS) _ (Mode 0) To disconnect the transmitter power just turn the power
key to “off” position. When the power key is switched from “on” to “off”, the transmitter will also
send a “Stop” command to the receiver for 3 seconds, the red status light flashes 3 times and at the
same time deactivate the MAIN relay.

Shutting Off the Transmitter(POS) _ (Mode 1) To disconnect the transmitter power just turn the power
key to “off” position. When the power key is switched from “on” to “off”, the transmitter will also
send a “Stop” command to the receiver for 3 seconds and at the same time deactivate the MAIN relay.

5. The emergency stop button is a right-rotate momentary spring-return type. To turn on the transmitter
and activate the MAIN relay, please elevate the emergency stop button again and rotate the transmitter
power key to “ON” position.
6. Note that the transmitter cannot be hit by outer force, so that malfunction can be prevented.
7. The operating temperature is -10 ~ +60℃. Avoid operating the transmitter in high temperature
workshop. If operating temperature is higher than 80℃, the auto shutdown protection installed inside
CPU will shut down the transmitter and deactivate the MAIN relay.
8. To operation normally, the battery power must over 2.2V. If the voltage is lower than 2.2V, the
system cannot be started and low voltage will be showed until the MAIN is completely shutdown.
9. If the power voltage is lower than 2.2V when transmitter is operated, the LV code will be “1” and low
voltage status light will be shown. For standard system, the transmitter will stop sending signals
when voltage is lower than 2.0V. But for EN ISO 13849-1 version, the transmitter will stop sending
signals when voltage is lower than 1.8V.

- 31 -

Downloaded from www.Manualslib.com manuals search engine

 Power status light

STOP: press → lock (emergency stop) STOP : Elevate clockwise → reset (Turn on the transmitter at any time)

8.2 Transmitter Status Light

Type Status Problem LED Indication

1 Place transmitter into
Charging Constant red light ON
charger

2 Power on when voltage is Blinking red light flash

BATT<2.2V
low ON_0.1/OFF_1.9 sec (until power off)
Set data by using Fast blinking on
3 Setting failed or invalided JUMPER & dip-switch
without following rules Red light ON_0.1/OFF_0.1 sec

4 Constant green light ON until transmitter

Setting completed JP1 or JP2 inserted
power shuts off.

5 EEPROM ID code does Constant red light ON until transmitter

EEPROM ID error
not match CPU data power shuts off
6 RF module abnormal PLL UNLOCK Red light ON_0.1/OFF_0.1 sec
7 ID even number error Setting error Red light ON_1/OFF_1 sec

8 Power on pushbutton Red light ON_1.9/OFF_0.1 sec (until

Pushbutton locked
connected power off)
BATT>=2.2V and all the
9 Normal power on pushbuttons are not All the lights ON_2 sec
depressed
MODE 0: Red light ON_0.5/ OFF_
10 STOP status STOP button is pressed 0.5sec, flash 30sec.
MODE 1: all the lights OFF

11 Low voltage during BATT<2.2V and press

Red light flash ON_0.1/OFF_1.9sec
operation pushbutton
Press and hold the pushbutton:
encoder board Blinking blinks ON_0.05/OFF_0.15
12 High temperature
temperature higher than second
protection
80℃
All pushbutton released: All lights are
off
- 32 -

Downloaded from www.Manualslib.com manuals search engine

 Activate MSSI/FSI
function:
13 Blinking red light, green light
FSI mode Depress FAN+SAFETY ON_0.1/OFF_0.1 second
button and hold for more
than 2 seconds.
14 Normal operation Press pushbutton Green light flash ON_0.1/OFF_1.9 sec
Remark:
Under high temperature protection, press every pushbutton will send null commands and the corresponding
pushbutton relay will be unlatched. In case of high temperature protection functions, please keep the transmitter
away from high temperature environment and shut off transmitter power. High temperature protection won’t be
deactivated only after the transmitter temperature is back to operating temperature -10 ~ +60℃ and restarted.

9. RECEIVER INSTALLATIO N
9.1 Preparation for Installation

1. Required Tools for Receiver Installation:

(1) Flat Head Screwdriver (-)

(2) Phillips Head Screwdriver (+)
(3) Multi-Meter
(4) 14mm Wrench x 2
(5) Power Drill withφ10.5mm Drill-Bit

2. Check to ensure that your receiver is not set to the same RF channel and ID code as any other
systems in operation at the same facility or within 300-meter distance.
3. Prior to installation, make sure that the crane or equipment itself is working properly.
4. Use a multi-meter to check the voltage source available and ensure the receiver voltage setting
matches your power source.
5. Prior to installation, switch off the main power source to the crane or equipment.

9.2 Step By Step Installation and Co mmissioning

9.2.1 Select the location

Select the location for installation and wiring: (Attention!!!)

α604/607/608
1. For better reception, the location selected should have the antenna visible from all areas where the
transmitter is to be used.
2. The location selected should not be exposed to high levels of electrical noise. Mounting the
receiver next to an unshielded variable frequency control (inverter) may cause minor interference.

- 33 -

Downloaded from www.Manualslib.com manuals search engine

 If it is unavoidable, please consider using antenna with external coaxial cable to relocate the
antenna to better signal receipt position.
3. Always locate the receiver unit as far away from high voltage wiring or equipment, such as: motor,
relay, magnetic valve, inverter controls and output cable…etc. as possible. Be sure to install the
receiver at least 2 meters away from the inverter. If the receiver is installed on the control box,
then the antenna position has to be higher than the control box. (as Fig.14)

α612
Drill four holes (dia.10.5mm) base on the position of the receiver shock absorbers. (Fig.15)

9.2.2 Commissioning steps

1. Decide the wiring type and cable. If the cable gland is used for the cable, please use the enclosed
rubber cork to seal the cable gland without cable.
2. For system wiring, please refer to the output contact diagrams from page 13.
3. Ensure the selected location has adequate space to accommodate the receiver enclosure.
4. Make sure the receiver unit is in upright position (vertical).
NOTE!! The distance between the antenna and the control panel should be as far apart as
possible (refer to the fig.14 & 15).
5. If a crane or equipment’s runway is longer than 100 meters, an external antenna should be added.
The Alpha 608 receiver housing has provisions for an external factory installed antenna available as
an option, contact your dealer for price and delivery.
6. Drill a hole on the control panel (10.5mm).
7. Tightened the bolt nuts provided.
8. If the control panel has a plastic surface, extended grounding wire should be used.
9. Ensure all wiring is correct and safely secured and all screws are fastened.

2 5 5 mm
4 - O10.5

2 7 8 mm

(Fig.14) Alpha 604, 607, 608 Models (Fig.15) Alpha 612 Models

- 34 -

Downloaded from www.Manualslib.com manuals search engine

 9.3 System Testing

1. Connect the power source to the receiver and test the MAIN relay output by pressing the red
emergency stop button (EMS) and observe that it properly opens and closes the main line disconnect
contactor.
2. Test the operation of each function to ensure it corresponds to the transmitter direction labels and/or
the pendant it is replacing.
3. Test the limit switches on the hoist and/or crane and verify they are working properly.
4. If your new remote control is replacing an existing pendant, make sure it is completely disconnected
to prevent unwanted control commands, i.e. snick circuits.
5. If your new remote control is replacing an existing pendant make sure it is stored in a safe location
where it will not interfere with remote operation (get torn off).

9.4 Receiver system Status LED Display

LED status light

FU
SE

- 35 -

Downloaded from www.Manualslib.com manuals search engine

 Receiver system Status LED Display
Type Led Indication Problem and Solution
EEPROM error – reprogramming required.
1 Constant red light.
Incorrect receiver ID code setting (see note below).
ON → 1.0 second ID code not matched on both the transmitter and
2
OFF → 1.0 second receiver unit, please readjust accordingly.
3 Dim or no light. Under-voltage, check the main power-supply.
ON → 2.0 seconds
4 MAIN contact relay jammed or defective.
OFF → 0.1 second
ON → 0.1 second System normal with transmitter pushbutton either in
5
OFF → 2.0 seconds neutral or in transmitter power “off” position.
ON → 0.1 second System normal with transmitter pushbutton in
6
OFF → 0.1second non-neutral position (pushbutton depressed).
Note: Please refer to section 7.1 on page 20 for correct ID code setting.

Alpha 612 Receiver System Status LED Display

Led Indication Reason Solution
ON Normal-voltage
Power LED display
OFF Under-voltage
Transmitted signals detected
ON
and received
OFF No transmitting signal detected
SQ, Status LED display
1.Transmitter standby Turn on the transmitter
BLINK
2.Interference Turn off the transmitter

ON Normal operation
Relay LED display
OFF Receiver defective Repair decoder board

- 36 -

Downloaded from www.Manualslib.com manuals search engine

 10. BATTERY CH ARG ER

10.1 Charger Operation

Electromagnetic Induction Charge

 The electromagnetic induction charger with undisclosed metal charging contacts on transmitter
provides immediate charging simply by sliding the transmitter into the charger. It is not necessary to
open the battery cover to replace batteries.
 To avoid rain, high temperature, humidity and corroding air, please place or install the battery charger
indoor with good ventilation. Keep 5cm space for two sides of the charger to keep the heat out. The
suggesting temperature range is 0 ~ 40℃.

(Fig. 16) Front view

 Battery charger voltage AC100~240V 50/60Hz, power consumption 10W。

 Use Nickel-Metal low self-discharge Hydride (NI-MH) 2000mA, AA size*2 rechargeable batteries.
Charging can be completed in 3 hours.
 Set the power switch on the OFF position whenever transmitter is not operated. Press E-STOP button
and slide-in the transmitter into the charger to charge. The transmitter is suggested to be charged
whenever it is not operated. The power switch should be rotated to OFF position while charging,
otherwise charging cannot be proceeded.
 The charger status light shows red when transmitter is charging; transmitter status light will be off
when charging is completed or failed. Please refer to below Battery Charger LED Status Light for
details. The charger status light shows green when charging is completed.
 Charger power LED: green

- 37 -

Downloaded from www.Manualslib.com manuals search engine

  When the rechargeable batteries are placed under low temperature environment, the activity is low and
the “charging completed” LED will display in a shorter time than usual. To avoid such condition,
please recharge the batteries within 0 ~ 40℃. Under lower temperature environment (below 0℃), the
running down batteries will complete charging within half an hour. That means the charging is
completed earlier than scheduled. Please take out the transmitter from charger and insert it into
charger again to proceed with charging normally.
 If the rechargeable batteries are not used for a longer period of time, the charging will be completed in
a shorter time than usual. To charge normally, please take out the transmitter from charger and insert
it into charger again.
 Please change the two rechargeable batteries at the same time to charge or discharge completely.

POWER

: Charging completed
: Charging
: Charging failed

Slide-in transmitter into battery charger (transmitter vinyl protective cover has to be taken off)

α604
α612
※ Note: The rechargeable battery has to be recharged within 6 months after the manufacturing date.

- 38 -

Downloaded from www.Manualslib.com manuals search engine

 10.2 Battery Charger LED Status Light

Item Status Condition Status Light

1 Startup check Within 2 seconds after power is on Red + Green LED for 2 sec
No battery inside transmitter battery
2 Charging failed holder or non-rechargeable battery is Red LED OFF_0.1/ON_1.9 sec
used.
3 Charging Charging procedure is normal Red LED ON
4 Charging completed Charging procedure is completed Green LED ON
5 Standby No transmitter in the charger Not lit

11. TRO UBLE SH O O TING

Should the operator find the equipment not operating normally, please check the chart below for simple
trouble shooting tips.

Problem Possible Reason Solution

Ensure the correct transmitter is

Transmitter does Transmitter and the receiver are
in use. The labels on the receiver
not communicate not on the same RF channel
and the transmitter will identify the
with the receiver. (SQ lamp not lit) or ID code.
RF channel and ID code in use.

Turn “on” the transmitter with

EMS elevated. If the status LED
Transmitter does
Low or no transmitting power shows blinking red light or no
not communicate
from the transmitter unit. light at all, then turn the power
with the receiver.
“off” and replace the two alkaline
“AA” batteries.

No power to the Ensure power input to the receiver

receiver (AC power Blown fuse or no input power unit is correct. If the power
indicator on the connection. indicator (AC) is still not lit, please
receiver unit not lit). check the receiver for any open fuse.

Receiver configuration is not set Please refer to section 6 and 7

Outputs do not
properly or output wiring is to ensure receiver is correctly wired
operate correctly.
incorrect. and configured for your application.

Transmitter does Elevate the EMS first and then

Transmitter is turned on with the
not communicate turn the power switch off and
EMS activated (pressed down).
with the receiver. then on again.

- 39 -

Downloaded from www.Manualslib.com manuals search engine

 12. S YS TEM S PECIFICATIO N

Transmitter Unit

Source Voltage : Ni-MH AA size x 2 battery 2.4V (no contact charging)

Or AA alkaline x 2 batteries 3.0V
Antenna Impedance : Internal Antenna 50 ohms. External antenna is available.
Dimension : 604 Models : 140mm x 68mm x 30mm
607, 608 Models: 189mm x 68mm x 30mm
612 Models : 235mm x 68mm x 30mm
Weight : 604 Models : 220g (include batteries)
607, 608 Models: 280g (include batteries)
612 Models : 350g (include batteries)
Enclosure Rating : IP-65
Operating Temperature : -10 ~ +60℃(> 80℃ high temperature protection )
Transmitting Power Consumption : < 30mA @ 3.5V
(Various from encoding mode and transmitting power)
Continue Operating Time : > consecutive 100hrs @batteries full (2000mA), Band 301,
433MHz, Transmitting Power 1mW

Transmitting RF Board Unit

Frequency Range : 301, 433 MHz

Transmitting Power : 0.1 mW – 10mW
Frequency Control : VTCXO ( PLL)
Frequency Deviation : < 1ppm @ 25℃
Spurious Emission : < - 50dB
Emission : F1D
Antenna Impedance 50 ohms
Operating Temperature : -10℃ ~ +60℃
Low Voltage : 2.2V – 2.0V

Charger Unit

Dimension : 120mm x 105mm x 105mm

Voltage : 100~240V 50/60Hz
Power Consumption : Max.10 Watt
Operating Temperature : 0℃~ +40℃
Heat Ventilation : Temperature Control Fan
Charging Current : About 600mA @3V
Charging Time : About 3hrs @2000mAh
Charging Detection : -ΔV + Temperature

- 40 -

Downloaded from www.Manualslib.com manuals search engine

 Receiver Unit

Frequency Band : BRXN – 301, 433 MHz

Channel Spacing : 25KHz (BRX-301, 433)
Frequency Control : VTCXO (PLL)
Frequency Drift : < 5ppm @ -20℃ ~ +70℃
Frequency Deviation : < 1ppm @ 25℃
Sensitivity <-115dBm
Spurious Emission : - 50dB
Antenna Impedance : 50 ohms
Responding Time 40ms (Normal)
Enclosure Rating : IP-65
Source Voltage : α604/607/608: DC12V-24V, AC48V, AC110V, AC220V,
AC230V, AC240, AC380V
Full voltage module: AC100-240V @50/60Hz
α612: DC12V-24V, AC25/36/42/50V, AC110V/240V,
AC380-460V @50/60Hz
Power Consumption α604: 8 Watt
α607/8: 10 Watt
α612: 15 Watt
Operating Temperature : -10℃ ~ +70℃
Output Contact Rating 250V @ 10A
Output MAIN Relay Rating 250V @ 6A
607, 608 Models:310mm x 134mm x 72mm
612 Models : 300mm x 230mm x 86mm
Weight : 604 Models : 1,625g (include output cable)
607, 608 Models: 2,000g (include output cable)
612 Models : 3,400g (include output cable)

- 41 -

Downloaded from www.Manualslib.com manuals search engine

 13.PARTS LIS T
1. Transmitter RF module (Alpha 604) BTX433
2. Encoder board (Alpha 604A) BEN604A
Encoder board (Alpha 604B) BEN604B
Encoder board (Alpha 607A) BEN607A
Encoder board (Alpha 607B) BEN607B
Encoder board (Alpha 607AT) BEN607AT
Encoder board (Alpha 607BT) BEN607BT
Encoder board (Alpha 608A) BEN608A
Encoder board (Alpha 608B) BEN608B
Encoder board (Alpha 608AT) BEN608AT
Encoder board (Alpha 608BT) BEN607BT
3. A608 electromagnetic induction board ELE600
4. Transmitter enclosure (Alpha 604) BCT604
Transmitter enclosure (Alpha 607 & 608) BCT607
Transmitter enclosure (Alpha 612) BCT612
5. Battery cover BC600
6. 2-step pushbutton B50001
1-step pushbutton B50002
7. Pushbutton rubber boot fixing holder BCH608
8. Pushbutton rubber boot (Alpha 604) PRB01
Pushbutton rubber boot (Alpha 607 & 608) PRB02
Pushbutton rubber boot (Alpha 612) PRB03
9. Transmitter shock-absorbing rubber (All models) SAR02
10. Transmitter vinyl protective cover (Alpha 604) VPC01
Transmitter vinyl protective cover (Alpha 607 & 608) VPC02
Transmitter vinyl protective cover (Alpha 612) VPC03
11. EMS pushbutton B50003
12. EMS red cap EMS01
13. A600 waist strap WS01
14. Rechargeable battery RCB01
15. A600 pushbutton direction label DL01

Receiver Part No.

1. 433MHz receiver RF module (All models) BRX433
2. Decoder board (Alpha 604A) BDE604A
Decoder board (Alpha 604B) BDE604B
Decoder board (Alpha 607A) BDE607A
Decoder board (Alpha 607B) BDE607B
Decoder board (Alpha 607AT) BDE607AT
Decoder board (Alpha 607BT) BDE607BT
Decoder board (Alpha 608A) BDE608A
Decoder board (Alpha 608B) BDE608B
Decoder board (Alpha 608AT) BDE608AT
Decoder board (Alpha 608BT) BDE608BT
3. Receiver enclosure (Alpha 604/607/608) BCR607
Receiver enclosure (Alpha 612) BCR612
4. Receiver mounting spring (Alpha 604/607/608) RMS600
5. Regular Output Contact Relay-blue (All Models) BDE607BT
6. Safety MAIN Contact Relay-DC12V (All Models) BDE608A
7. Transformer (12-24VDC – Alpha 600-608, 612) T24VDC
Transformer (48VAC – Alpha 600-608) T48VAC
Transformer (110VAC – Alpha 600-608) T110VAC
Transformer (220VAC – Alpha 600-608) T220VAC
- 42 -

Downloaded from www.Manualslib.com manuals search engine

 Transformer (230VAC – Alpha 600-608) T230VAC
Transformer (240VAC – Alpha 600-608) T240VAC
Transformer (380VAC – Alpha 600-608) T380VAC
Transformer (25/36/42/50VAC – Alpha 612) T25/36/42/50VAC
Transformer (110/240VAC – Alpha 612) T110/240VAC
Transformer (380/460VAC – Alpha 612) T380/460VAC
8. Full voltage module (100-240VAC-Alpha 600-608) FV100-240VAC
9. 2-meter Output Cable with 5 Common Circuits Cable (24C*2m V3.5, Alpha 607, 608) OC607
10. Optional External 433 MHz Antenna (All Models) ANT433

Charger/USB programming parts

1. Charging board CHPCB600
2. Electromagnetic board ELEPCB
3. Charger casing CHC600
4. Charging cable CHCA
5. Charger holder CHH600
6. USB programming board USBPCB
7. USB connecting cable (1m) USBC

- 43 -

Downloaded from www.Manualslib.com manuals search engine