S200, S300, S500, S1700, S2700, S3700, S5700, and

S6700 Switches

Hardware Installation and

Component Replacement

Issue 30
Date 2023-03-30

HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2023. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.

Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees
or representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China

Website: https://e.huawei.com

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. i

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement Contents

Contents

1 About This Document.............................................................................................................1

2 Hardware Installation and Component Replacement (Remote Unit)....................... 4
2.1 Remote Unit Overview.......................................................................................................................................................... 4
2.2 Installation Preparation......................................................................................................................................................... 5
2.2.1 Safety Precautions............................................................................................................................................................... 5
2.2.2 Checking the Installation Site.......................................................................................................................................... 6
2.2.3 Checking the Power Supply System.............................................................................................................................. 7
2.2.4 Preparing Installation Tools and Accessories............................................................................................................. 8
2.3 Installing a Remote Unit.................................................................................................................................................... 12
2.3.1 Installation Scenario Overview..................................................................................................................................... 12
2.3.2 Scenario 1: Installing a Remote Unit on a Rapid Duct......................................................................................... 12
2.3.2.1 Installing a Remote Unit on a Rapid OBO45 Duct.............................................................................................13
2.3.2.2 Installing a Remote Unit on a Rapid OBO80 Duct.............................................................................................17
2.3.3 Scenario 2: Installing a Remote Unit on a Workbench........................................................................................ 20
2.3.4 Scenario 3: Installing a Remote Unit on a Wall......................................................................................................22
2.3.5 Scenario 4: Installing a Remote Unit in a Network Box...................................................................................... 26
2.3.6 Scenario 5: Installing a Remote Unit on a DIN Rail.............................................................................................. 31
2.4 Component Replacement...................................................................................................................................................34
2.4.1 Replacing a Remote Unit................................................................................................................................................ 34

3 Hardware Installation and Component Replacement (Fixed Switches)..................37

3.1 Switch Overview.................................................................................................................................................................... 37
3.2 Installation Overview...........................................................................................................................................................38
3.3 Preparing for Installation................................................................................................................................................... 39
3.3.1 Safety Precautions............................................................................................................................................................. 39
3.3.2 Checking the Installation Site....................................................................................................................................... 41
3.3.3 Checking the Cabinet or Rack....................................................................................................................................... 44
3.3.4 Checking the Power Supply System............................................................................................................................ 47
3.3.5 Preparing Installation Tools and Accessories........................................................................................................... 48
3.4 Unpacking a Switch..............................................................................................................................................................51
3.5 Installing a Switch................................................................................................................................................................ 55
3.5.1 Installation Scenario Overview..................................................................................................................................... 55
3.5.2 Scenario : Cabinet/Rack Mounting.............................................................................................................................. 65

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. ii

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement Contents

3.5.2.1 Using Front Mounting Brackets................................................................................................................................ 65

3.5.2.2 Using Front and Rear Mounting Brackets............................................................................................................. 70
3.5.2.3 Using Front Mounting Brackets or Cable Management Frames and Rear Mounting Brackets......... 83
3.5.2.4 Using Horizontal Rack-mounting Kit...................................................................................................................... 88
3.5.3 Scenario: Desk Mounting................................................................................................................................................ 91
3.5.4 Scenario: Wall Mounting................................................................................................................................................ 93
3.5.4.1 Mounting a Switch on the Wall Using Expansion Bolts (With Mounting Brackets).............................. 93
3.5.4.2 Mounting a Switch on the Wall Using Expansion Bolts (Without Mounting Brackets)........................96
3.5.5 Scenario: Top Wall Mounting........................................................................................................................................ 99
3.5.6 Scenario: Network Box Mounting............................................................................................................................. 102
3.5.7 Scenario: DIN Rail Mounting...................................................................................................................................... 105
3.5.8 Connecting the Ground Cable.................................................................................................................................... 106
3.6 Installing Modules.............................................................................................................................................................. 109
3.6.1 Installing a Pluggable Power Module...................................................................................................................... 109
3.6.2 Installing a 260 W or 240 W Independent Power Module............................................................................... 112
3.6.3 Installing a 60 W Independent Power Module..................................................................................................... 113
3.6.4 Installing a Card.............................................................................................................................................................. 115
3.6.5 Installing an Optical Module...................................................................................................................................... 117
3.7 Installing an HDF................................................................................................................................................................ 119
3.8 Connecting a Switch.......................................................................................................................................................... 121
3.8.1 Connecting Power Cables.............................................................................................................................................121
3.8.2 Connecting Ethernet Cables........................................................................................................................................ 132
3.8.3 Connecting Optical Fibers............................................................................................................................................ 137
3.8.4 Connecting Copper Cables........................................................................................................................................... 139
3.8.5 Assembling the First-Generation Hybrid Cables.................................................................................................. 141
3.8.5.1 Assembling Optical Fibers in the First-Generation Hybrid Cable in Mechanical Splicing Mode..... 150
3.8.5.2 Assembling Optical Fibers in the First-Generation Hybrid Cable in Fusion Splicing Mode...............157
3.8.5.3 Assembling Copper Cores in the First-Generation Hybrid Cables.............................................................. 159
3.8.6 Connecting the First-Generation Hybrid Cables...................................................................................................162
3.8.7 Assembling Second-Generation Hybrid Cable...................................................................................................... 163
3.8.8 Connecting Second-Generation Hybrid Cable...................................................................................................... 175
3.9 Post-installation Checks................................................................................................................................................... 179
3.10 (Optional) Installing an RPS1800...............................................................................................................................180
3.10.1 Installing the RPS1800 in a Cabinet or Rack.......................................................................................................180
3.10.2 Installing a Power Module in the RPS1800......................................................................................................... 181
3.10.3 Connecting the RPS1800 to a Switch.................................................................................................................... 183
3.11 Powering on a Switch for the First Time................................................................................................................. 186
3.12 First Login to a Device....................................................................................................................................................187
3.13 Component Replacement.............................................................................................................................................. 188
3.13.1 Replacing a Power Module or Fan Module......................................................................................................... 189
3.13.2 Replacing an Optical Module................................................................................................................................... 191
3.13.3 Replacing a Card........................................................................................................................................................... 194

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. iii

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement Contents

3.13.4 Replacing a Switch....................................................................................................................................................... 195

3.13.5 3D Videos for Parts Replacement........................................................................................................................... 197

4 Appendix............................................................................................................................... 198
4.1 Appendix A On-site Cable Assembly and Installation........................................................................................... 198
4.1.1 Cable Assembly Precautions........................................................................................................................................198
4.1.2 Installing Cable Accessories......................................................................................................................................... 199
4.1.2.1 Precautions for Installing Cable Accessories...................................................................................................... 199
4.1.2.2 Installing Power Adapters.........................................................................................................................................201
4.1.2.2.1 Installing the OT Terminal.................................................................................................................................... 201
4.1.2.2.2 Installing the Cord End Terminal........................................................................................................................ 203
4.1.2.3 Installing Fiber Connectors.......................................................................................................................................204
4.1.2.3.1 Cleaning Fiber Connectors.................................................................................................................................... 205
4.1.2.3.2 Installing an LC Fiber Connector......................................................................................................................... 205
4.1.2.3.3 Installing the SC Fiber Connector....................................................................................................................... 207
4.1.2.3.4 Installing an MPO Connector...............................................................................................................................208
4.2 Appendix B Environmental Requirements for Device Operation....................................................................... 209
4.2.1 Environmental Requirements for an Equipment Room..................................................................................... 209
4.2.1.1 Requirements for Selecting a Site for an Equipment Room......................................................................... 209
4.2.1.2 Equipment Room Layout.......................................................................................................................................... 211
4.2.1.3 Construction Requirements for the Equipment Room....................................................................................211
4.2.1.4 Equipment Room Environment...............................................................................................................................213
4.2.1.5 Requirements for Corrosive Gases......................................................................................................................... 214
4.2.1.6 Requirements for ESD Prevention.......................................................................................................................... 214
4.2.1.7 Electromagnetism Requirements for the Equipment Room......................................................................... 215
4.2.1.8 Requirements for Lightning Proof Grounding................................................................................................... 215
4.3 Appendix C Equipment Grounding Specifications................................................................................................... 217
4.3.1 General Grounding Specifications............................................................................................................................. 217
4.3.2 Grounding Specifications for an Equipment Room............................................................................................. 218
4.3.3 Grounding Specifications for Signal Cables........................................................................................................... 218
4.3.4 Specifications for Laying Out Grounding Cables..................................................................................................219
4.4 Appendix D Engineering Labels for Cables................................................................................................................219
4.4.1 Engineering Labels for Optical Fibers...................................................................................................................... 219
4.4.1.1 Labels for the Optical Fibers Connecting Devices............................................................................................ 220
4.4.1.2 Labels for the Optical Fibers Connecting the Device and an ODF.............................................................221
4.4.2 Engineering Labels for Network Cables.................................................................................................................. 222
4.4.3 Engineering Labels for User Cables.......................................................................................................................... 224
4.4.4 Engineering Labels for Power Cables....................................................................................................................... 225
4.4.4.1 Engineering Labels for DC Power Cables............................................................................................................ 225
4.4.4.2 Engineering Labels for AC Power Cables.............................................................................................................227
4.5 Appendix E Guide to Using Optical Modules........................................................................................................... 228
4.6 Appendix F Fault Tag.........................................................................................................................................................231

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. iv

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 1 About This Document

1 About This Document

Intended Audience
This document describes installation procedures, troubleshooting methods, and
maintenance instructions for the S series fixed switches.
This document is intended for network engineers responsible for switch
installation and maintenance. You should have experience in network device
installation and maintenance.

Symbol Conventions
The symbols that may be found in this document are defined as follows.

Symbol Description

Indicates a hazard with a high level of

risk which, if not avoided, will result in
death or serious injury.

Indicates a hazard with a medium

level of risk which, if not avoided,
could result in death or serious injury.

Indicates a hazard with a low level of

risk which, if not avoided, could result
in minor or moderate injury.

Indicates a potentially hazardous

situation which, if not avoided, could
result in equipment damage, data loss,
performance deterioration, or
unanticipated results.
NOTICE is used to address practices
not related to personal injury.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 1

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 1 About This Document

Symbol Description

Supplements the important

information in the main text.
NOTE is used to address information
not related to personal injury,
equipment damage, and environment
deterioration.

Command Conventions
The command conventions that may be found in this document are defined as
follows.

Convention Description

Boldface The keywords of a command line are in boldface.

Italic Command arguments are in italics.

[] Items (keywords or arguments) in brackets [ ] are

optional.

{ x | y | ... } Optional items are grouped in braces and separated

by vertical bars. One item is selected.

[ x | y | ... ] Optional items are grouped in brackets and

separated by vertical bars. One item is selected or
no item is selected.

{ x | y | ... }* Optional items are grouped in braces and separated

by vertical bars. A minimum of one item or a
maximum of all items can be selected.

[ x | y | ... ]* Optional items are grouped in brackets and

separated by vertical bars. Several items or no item
can be selected.

&<1-n> The parameter before the & sign can be repeated 1

to n times.

# A line starting with the # sign is comments.

Disclaimer
● This document is designed as a reference for you to configure your devices. Its
contents, including web pages, command line input and output, are based on
laboratory conditions. It provides instructions for general scenarios, but does
not cover all use cases of all product models. The examples given may differ
from your use case due to differences in software versions, models, and
configuration files. When configuring your device, alter the configuration
depending on your use case.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 2

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 1 About This Document

● The specifications provided in this document are tested in a lab environment

(for example, a certain type of cards have been installed on the tested device
or only one protocol is run on the device). Results may differ from the listed
specifications when you attempt to obtain the maximum values due to factors
such as differences in hardware configurations and carried services.
● In this document, public IP addresses may be used in feature introduction and
configuration examples and are for reference only unless otherwise specified.

Device Dimension Conventions

The dimensions described in this document are theoretically typical dimensions
and do not include dimension tolerances.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 3

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

2 Hardware Installation and Component

Replacement (Remote Unit)

2.1 Remote Unit Overview

2.2 Installation Preparation
2.3 Installing a Remote Unit
2.4 Component Replacement

2.1 Remote Unit Overview

Huawei S5731-L and S5731S-L series devices are GE remote units built on the
innovative simplified architecture. They can be deployed and used independently
as unmanaged switches or used together with Huawei's other series of campus
switches to implement simplified and efficient networking. Remote units can
function as the extended ports of the central switch, implementing flexible port
expansion.
S5731-L and S5731S-L series devices differ in dimensions (H x W x D), as well as
installation scenarios and installation methods. For details, refer to 2.3.1
Installation Scenario Overview. For details about the dimensions of different
remote unit models, see S5700 Series Switches Hardware Description.

NOTE

All figures are for illustration purposes only and may not accurately depict actual devices or
modules.

CAUTION

Huawei's S series fixed switches are class A products. In a domestic environment,

they may cause radio interference, in which case users may be required to take
adequate measures.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 4

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

2.2 Installation Preparation

2.2.1 Safety Precautions

Before you start the installation procedure, read all safety precautions described in
this document and observe any warning labels affixed to the remote unit. Doing
so ensures your safety and protects the remote unit from damage.
Safety precautions provided in this document may not cover every eventuality, so
remain mindful of safety at all times.
Only trained and qualified personnel are allowed to install, operate, or maintain
Huawei's remote units.

General Safety Guidelines

CAUTION

Always take precautions against ESD whenever you operate a remote unit. For
example, wear ESD gloves or an ESD wrist strap. To avoid electric shock or burn,
remove conductive objects like jewelry and watch.

WARNING

● Ground the remote unit before installing it. Do not operate the remote unit in
the absence of a properly installed ground conductor.
● Remove the ground cable only after all the other cables and modules have
been removed from the remote unit.
● If electric leakage occurs at the ground point, the remote unit may fail to work
properly.

Environmental Safety

DANGER

Do not install a remote unit in an environment with flammable or explosive gases

or smoke.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 5

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

NOTICE

● Install a remote unit in a dry environment away from sources of water, as

water or damp may damage circuits of the remote unit.
● The installation site must be well ventilated to prevent remote units from
overheating.

Electrical Safety

DANGER

● Direct contact with a high-voltage power source or indirect contact through

damp objects can be fatal. Misoperations on high-voltage facilities may result
in fire, electric shock, or other accidents.
● Never install or remove a remote unit or power cables while the power is on.
Transient contact between the core of a power cable and a conductor may
generate electric arcs or sparks that can cause fire and hurt human eyes.
● To ensure personal and equipment safety, ground the remote unit before
powering it on.

Laser Safety

CAUTION

● Never look directly into an optical module or the ends of optical fibers. Optical
modules and connected optical fibers emit laser beams that can cause eye
damage.
● Cover fiber connectors with dust caps when they are not connected.

Mechanical Safety

CAUTION

Never attempt to lift objects that are too heavy for one person to handle. Instead,
seek help or use appropriate tools.

2.2.2 Checking the Installation Site

Remote units must be used in an indoor environment with temperature under

control. Table 2-1 describes the requirements for the installation site.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 6

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Table 2-1 Requirements for the installation site

Item Requirement

Cleanliness Remote units must be installed in a clean, dry, and well

ventilated environment with stable temperature. The
installation site must be free from leaking or dripping
water and dew.

Dust proofing The installation site must not have an excessive amount of
dust. A buildup of dust may cause electrostatic discharge
on the remote unit and impair electrical connections,
which will reduce the service life and may cause failure of
the remote unit.

Temperature and The remote unit must be installed in a temperature-

humidity controlled environment where the temperature and
humidity are within specifications.
The ambient temperature of the installation site should
not exceed 45°C (40°C at most for the S5731-L4P2HW-
RUA and S5731S-L4P2HW-RUA). In environments where
the relative humidity exceeds 70%, use dehumidifiers or
dehumidifying air conditioners.

Corrosive gas The installation site must be free from acidic, alkaline, or
avoidance corrosive gases.

Heat dissipation ● Keep remote units away from direct sunlight.

space ● Reserve sufficient space around the remote units to
facilitate heat dissipation. The heat dissipation space
requirements are related to the installation scenarios.
For details, see 2.3 Installing a Remote Unit.

2.2.3 Checking the Power Supply System

Table 2-2 lists the power supply requirements when remote units are installed.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 7

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Table 2-2 Power supply requirements

Item Requirement

Voltage The input voltage must be within the specifications of

remote units. When a remote unit is powered by a power
adapter, the input and output voltage ranges of the power
adapter are as follows:
● Input voltage range of the power adapter:
– Rated voltage range: 100 V AC to 240 V AC, 50/60
Hz
– Maximum voltage range: 90 V AC to 264 V AC, 47
Hz to 63 Hz
● Output voltage range of the power adapter: 54 V DC to
57 V DC

Power outlets and ● The AC power cables used on the devices must comply
power cables with the local standards.
● Use standard power adapters provided by Huawei to
supply power to remote units. Otherwise, the remote
units may not work properly or security risks may be
introduced.
● The power cables and connectors delivered with a
device are for use with this device only. Do not use
them on other devices.

2.2.4 Preparing Installation Tools and Accessories

Table 2-3 lists the tools and accessories required for installing a remote unit.

Table 2-3 Installation tools and accessories

Tool or Description Picture
Accessory

ESD gloves Used to

prevent ESD
damage.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 8

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Tool or Description Picture

Accessory

Protective Used to
gloves protect hands
against
lacerations
and abrasions.

ESD wrist Used to

strap prevent ESD
damage. Wear
the strap on
your wrist and
insert the
other end into
the ESD jack
on the
cabinet.

Utility knife Used to cut

cartons or
paper.

Hacksaw Used to cut

the cover
plate for a
rapid duct.

Measuring Used to
tape measure
distances.

Marker Used to mark

the
installation
positions of
components.

Flat-head Used to turn

screwdriver slotted-head
screws and
bolts.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 9

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Tool or Description Picture

Accessory

Phillips Used to turn

screwdriver cross-head
screws and
bolts.

Diagonal Used to cut

pliers insulation
tubes and
cable ties.

Cable tester Used to test

the
connectivity
of Ethernet
cables.

Multimeter Used to test

cabinet
insulation,
cable
connectivity,
and device
electrical
performance,
including
voltage,
current, and
resistance.

Hammer Used to drill

drill holes. Choose
appropriate
drill bits
according to
the hole
depth and
expansion
bolt models.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 10

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Tool or Description Picture

Accessory

Adjustable Used to
wrench tighten or
loosen hex or
square bolts
and nuts. The
span can be
adjusted to
suit bolts or
nuts of
different sizes.

Table 2-4 lists the accessories required for installing a remote unit.

Table 2-4 Installation accessories

Accessory Description Picture

Cable tie Used to

bundle cables.

Fiber Used to
binding bundle optical
tape fibers.

Insulation Used to
tape insulate
power wires
or other
conductors.

Corrugated Used to
pipe protect optical
fibers.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 11

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

2.3 Installing a Remote Unit

2.3.1 Installation Scenario Overview

The installation scenarios of remote units vary with their dimensions.

Table 2-5 Installation scenarios

Dimensions 2.3.2 2.3.3 2.3.4 2.3.5 2.3.6
(H x W x D) Scenario Scenario Scenario 3: Scenario 4: Scenario
1: 2: Installing a Installing 5:
Installing Installing Remote a Remote Installing
a Remote a Remote Unit on a Unit in a a
Unit on a Unit on a Wall Network Remote
Rapid Workbenc Box Unit on a
Duct h DIN Rail

45.0 mm x Supported Not Not Not Supporte

90.0 mm x supported supported supported d
75.0 mm

27.0 mm x Not Supported Supported Supported Not

185.0 mm x supported supporte
115.0 mm d

38.0 mm x Not Supported Supported Supported Not

185.0 mm x supported supporte
115.0 mm d

27.0 mm x Not Supported Supported Supported Not

210.0 mm x supported supporte
130.0 mm d

38.0 mm x Not Supported Supported Supported Not

210.0 mm x supported supporte
130.0 mm d

The dimensions (H x W x D) of the S5731-L16P2SR-RUA and S5731S-L16P2SR-

RUA are 43.6 mm x 442.0 mm x 260.0 mm. The installation scenarios and
methods are the same as those of fixed switches of the same dimensions. For
details, see 3 Hardware Installation and Component Replacement (Fixed
Switches).

2.3.2 Scenario 1: Installing a Remote Unit on a Rapid Duct

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 12

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

2.3.2.1 Installing a Remote Unit on a Rapid OBO45 Duct

Context
This installation method is applicable to the S5731-L4P2HW-RUA and S5731S-
L4P2HW-RUA.
Prepare the following before the installation:
● The rapid OBO45 duct (OBO Bettermann GK53100LGR/6113002) has been
secured.
● The remote unit to be installed has been placed near the rapid duct for
convenient movement.
● In this scenario, only hybrid cables can be used for power supply, and
dedicated hybrid optical-electrical optical modules are required. Hybrid cables
need to be prepared and routed onsite. For details about how to prepare
hybrid cables, see 3.8.7 Assembling Second-Generation Hybrid Cable.

WARNING

The S5731-L4P2HW-RUA and S5731S-L4P2HW-RUA devices adopt natural heat

dissipation. Heat is dissipated mainly through the iron shell at the rear of the
panel. At room temperature, some parts of the iron shell are hot. Do not touch
these parts when operating the device.

NOTE

All figures are for illustration purposes only and may not accurately depict actual devices or
modules.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver
● Hacksaw
● Rapid OBO45 duct (prepared by the customer)

Procedure
Step 1 Wear an ESD wrist strap. Ensure that one end of the ESD wrist strap is grounded
and the other end is in close contact with your wrist.
Step 2 Based on the width of the decorative panel, cut the cover plates on both sides of
the rapid duct to reserve sufficient space for remote unit installation and cable
routing.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 13

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Figure 2-1 Cutting the cover plate

Step 3 Route the hybrid cables into the rapid duct.

Figure 2-2 Routing cables

Step 4 Connect one end of the ground cable to the ground screw on the right side of the
remote unit.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 14

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Figure 2-3 Connecting the ground cable

Step 5 Insert an optical module into an optical port on the remote unit and connect the
hybrid cable to the optical module.

Figure 2-4 Connecting cables

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 15

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Step 6 Install the remote unit into the rapid duct slot.

Figure 2-5 Installing a remote unit on a rapid duct

Step 7 Connect the other end of the ground cable to the ground point or ground bar.
Step 8 Install the decorative panel and seal the extra space with a cover plate.

Figure 2-6 Installing the decorative panel

NOTE

If multiple remote units are installed, ensure that the distance between every two remote
units is at least 1.2 m.

----End

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 16

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

2.3.2.2 Installing a Remote Unit on a Rapid OBO80 Duct

Context
This installation method is applicable to the S5731-L4P2HW-RUA and S5731S-
L4P2HW-RUA.

Prepare the following before the installation:

● The rapid OBO80 duct has been secured. The following models of rapid
OBO80 ducts are supported:
– OBO Bettermann GK-70110RW/6274300
– OBO Bettermann GK-70110CW/6274301
– OBO Bettermann GK-70110LGR/6274302
– OBO Bettermann GA-S70110RW/6279200
– OBO Bettermann GA-S70110EL/6279303
● The remote unit to be installed has been placed near the rapid duct for
convenient movement.
● In this scenario, only hybrid cables can be used for power supply, and
dedicated hybrid optical-electrical optical modules are required. Hybrid cables
need to be prepared and routed onsite. For details about how to prepare
hybrid cables, see 3.8.7 Assembling Second-Generation Hybrid Cable.
● If optical fibers need to be used, industrial optical modules are required.

WARNING

The S5731-L4P2HW-RUA and S5731S-L4P2HW-RUA devices adopt natural heat

dissipation. Heat is dissipated mainly through the iron shell at the rear of the
panel. At room temperature, some parts of the iron shell are hot. Do not touch
these parts when operating the device.

NOTE

All figures are for illustration purposes only and may not accurately depict actual devices or
modules.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver
● Hacksaw
● Installation kit for the rapid OBO80 duct
● Rapid OBO80 duct (prepared by the customer)

Procedure
Step 1 Wear an ESD wrist strap. Ensure that one end of the ESD wrist strap is grounded
and the other end is in close contact with your wrist.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 17

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Step 2 Based on the width of the decorative panel, cut the cover plates on both sides of
the rapid duct to reserve sufficient space for remote unit installation and cable
routing.

Figure 2-7 Cutting the cover plate

Step 3 Route cables, such as optical fibers, hybrid cables, and power cables with a power
adapter connected, into the rapid duct. The cables may vary with site
requirements.

Figure 2-8 Routing cables

Step 4 Install the remote unit into a mechanical part.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 18

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Figure 2-9 Installing a remote unit into a mechanical part

Step 5 Insert an optical module into an optical port on the remote unit, and connect an
optical fiber or a hybrid cable to the optical module. (Here, a hybrid cable is used
as an example.)
NOTE

Power adapters are required when optical fibers are used, and are not required when hybrid
cables are used.

Figure 2-10 Connecting cables

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 19

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Step 6 Connect one end of the ground cable to the ground screw on the right side of the
remote unit.

Step 7 Install the mechanical part into the duct slot and connect the other end of the
ground cable to the ground point or ground bar.

Figure 2-11 Installing a mechanical part into the duct slot

Step 8 Install the decorative panel and seal the extra space with a cover plate.

Figure 2-12 Installing the decorative panel

NOTE

If multiple remote units are installed, ensure that the distance between every two remote
units is at least 1 m.

----End

2.3.3 Scenario 2: Installing a Remote Unit on a Workbench

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 20

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Context
This installation method is applicable to the S5731-L (excluding the S5731-
L4P2HW-RUA) and S5731S-L (excluding the S5731S-L4P2HW-RUA).

NOTICE

● Do not stack the horizontally placed remote units.

● Do not install the remote unit outdoors. Remote units can only be installed
indoors.
● It is recommended that power adapters and optical fibers not be vertically
installed above remote units.
● Use standard power adapters provided by Huawei to supply power to remote
units. Otherwise, the remote units may not work properly or security risks may
be introduced.

NOTE

All figures are for illustration purposes only and may not accurately depict actual devices or
modules.

The following figure shows space requirements for heat dissipation.

Figure 2-13 Heat dissipation requirements for installing a remote unit on a

workbench

Tools and Accessories

● ESD wrist strap or ESD gloves
● Rubber pads (four for each non-PoE model, not required for PoE models)
● Security lock (optional, purchased separately)
NOTE

No rubber pads are delivered with a remote unit that cannot be installed on a workbench
or a remote unit of the PoE model.

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 21

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Step 2 (Optional) For a non-PoE remote unit, attach rubber pads to the remote unit.
Carefully turn the remote unit upside down and attach four rubber pads to the
round imprinted areas at the bottom of the remote unit.

Step 3 Place the remote unit gently on the workbench.

Figure 2-14 Installation on a workbench (1)

Figure 2-15 Installation on a workbench (2)

Step 4 (Optional) Install a security lock to lock the remote unit to the workbench to
protect the remote unit against theft.
NOTE

To determine whether a security lock can be installed, check for the security slot marked
with a padlock icon on the remote unit. If there is no security slot on the remote unit, it
means that the security lock is not supported.

----End

2.3.4 Scenario 3: Installing a Remote Unit on a Wall

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 22

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Context
This installation method is applicable to the S5731-L (excluding the S5731-
L4P2HW-RUA and S5731-L16P2SR-RUA) and S5731S-L (excluding the S5731S-
L4P2HW-RUA and S5731S-L16P2SR-RUA).

DANGER

Before drilling holes on a wall, make sure that no power cable is routed in the
wall. Otherwise, power cables in the wall may cause personal injury.

NOTICE

● Do not stack the horizontally placed remote units.

● Do not install the remote unit outdoors. Remote units can only be installed
indoors.
● It is recommended that power adapters and optical fibers not be vertically
installed above remote units.
● Use standard power adapters provided by Huawei to supply power to remote
units. Otherwise, the remote units may not work properly or security risks may
be introduced.
● Ensure that remote units are horizontally installed on a wall, with ports facing
downwards.

NOTE

All figures are for illustration purposes only and may not accurately depict actual devices or
modules.

The following figure shows space requirements for heat dissipation.

Figure 2-16 Heat dissipation requirements for installing a remote unit on a wall

Tools and Accessories

● Hammer drill
● Phillips screwdriver

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 23

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

● Wall anchors and mounting screws (two for each remote unit, separately
purchased)

Procedure
Step 1 Measure the distance between the two mounting holes on the rear panel of the
remote unit.

Step 2 Use a measuring tape to determine positions of two mounting holes, keep the two
positions aligned, and mark the positions with a marker. Ensure that the distance
between the two mounting holes is the same as that of the two holes on the
remote unit.

Step 3 Drill holes and install mounting screws.

1. Choose an appropriate drill bit according to the diameter of the mounting
screws.
2. Hammer the hollow wall anchors into the mounting holes.
3. Use a Phillips screwdriver to screw the mounting screws into the wall anchors.
Leave the screws protruding 10 mm from the wall.
NOTE

It is recommended that cap screws meeting the following requirements be used:

- Diameter of the shank: ≤ 4 mm
- Height of the shank: ≥ 25 mm
- Diameter of the head: 6 to 8 mm
- Height of the head: ≤ 2 mm

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 24

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Step 4 Align the mounting holes on the rear of the remote unit with mounting screws
and hang the remote unit on the mounting screws.

Figure 2-17 Mounting a remote unit on a wall

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 25

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Figure 2-18 Remote unit mounted on a wall

----End

2.3.5 Scenario 4: Installing a Remote Unit in a Network Box

Context
This installation method is applicable to the S5731-L (excluding the S5731-
L4P2HW-RUA and S5731-L16P2SR-RUA) and S5731S-L (excluding the S5731S-
L4P2HW-RUA and S5731S-L16P2SR-RUA).

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 26

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

NOTICE

● Do not stack the horizontally placed remote units.

● Do not install the remote unit outdoors. Remote units can only be installed
indoors.
● It is recommended that power adapters and optical fibers not be vertically
installed above remote units.
● Use standard power adapters provided by Huawei to supply power to remote
units. Otherwise, the remote units may not work properly or security risks may
be introduced.
● Do not route Ethernet cables or power adapter cables outside a network box.
● The remote unit installed in a network box must be operated and maintained
by professionals.
● Do not use an enclosed network box and ensure that the air intake and
exhaust vents are not blocked to ensure proper heat dissipation of the remote
unit.
● If the network box is installed indoors or in a corridor that is free from rain, the
network box must meet the requirements of IP31 rating protection. (The first
number "3" indicates that the network box can prevent a solid object with the
diameter greater than or equal to 2.5 mm from entering the network box. The
second number "1" indicates that vertically falling drops shall have no harmful
effects.)
● Only one PoE remote unit can be installed in a network box, and a maximum
of two non-PoE remote units can be installed in a network box.
● Remote units installed in a network box:
● For a PoE model, the maximum operating temperature of the remote units
is 35°C.
● For a non-PoE model, if one remote unit is installed in a network box, the
maximum operating temperature of the remote unit is 40°C. If two remote
units are installed in a network box, the maximum operating temperature
of the remote units is 35°C.

NOTE

All figures are for illustration purposes only and may not accurately depict actual devices or
modules.

The following figures show space requirements for heat dissipation.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 27

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Figure 2-19 One remote unit

Figure 2-20 Two remote units

A network box can be installed in concealed (embedded into a wall) or exposed

(mounted on a wall) mode. Table 2-6 lists the common network boxes and their
application scenarios.

Table 2-6 Network boxes and applicable remote units

Network Dimensions (H x W x D) Applicable Remote Unit

Type

Concealed 300 mm x 450 mm x 120 4-port/8-port, power supplied by the

installatio mm (11.81 in. x 17.72 in. x power adapter
n 4.72 in.)

300 mm x 400 mm x 120

mm (11.81 in. x 15.75 in. x
4.72 in.)

300 mm x 350 mm x 120 4-port/8-port, power supplied

mm (11.81 in. x 13.78 in. x through the hybrid cable
4.72 in.)

Exposed 300 mm x 450 mm x 100 4-port/8-port, power supplied by the

installatio mm (11.81 in. x 17.72 in. x power adapter
n 3.94 in.)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 28

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Network Dimensions (H x W x D) Applicable Remote Unit

Type

300 mm x 400 mm x 100

mm (11.81 in. x 15.75 in. x
3.94 in.)

300 mm x 350 mm x 100 8-port, power supplied through the

mm (11.81 in. x 13.78 in. x hybrid cable
3.94 in.)

300 mm x 300 mm x 100 4-port, power supplied through the

mm (11.81 in. x 11.81 in. x hybrid cable
3.94 in.)

Installing a remote unit in a network box

The method for installing a remote unit in a non-Huawei network box depends on
the network box specifications. When a remote unit is installed in a non-Huawei
network box, the preceding heat dissipation space requirements must also be
observed.

Figure 2-21 Installing a remote unit in a network box

● For an AC power supply system, it is recommended that the PE wire of the AC

power cable be used to ground the remote unit. The prerequisite is that the
PE wire of the AC power cable in the network box has been properly
grounded.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 29

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

● All devices in a network box are connected to the ground bar through ground
cables, and the ground bar is connected to an equipotential terminal in the
network box through a metal structure.
● The ground point of a fiber reinforcing rib needs to be connected to a ground
bar using a ground cable or to an equipotential terminal in the network box
through a metal structure.
● When the PE wire of the AC power cable in the network box cannot meet the
grounding requirements, ground the network box through an external ground
cable (PGND cable) and ensure that the fiber reinforcing rib is disconnected
from the device ground point.

Figure 2-22 Remote unit installed in a network box (power supplied by a power
adapter)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 30

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Figure 2-23 Remote unit installed in a network box (power supplied through the
hybrid cable)

2.3.6 Scenario 5: Installing a Remote Unit on a DIN Rail

Context
● The DIN rail has been secured in position.
● The remote unit is placed near the DIN rail for convenient movement.
● In this scenario, only hybrid cables can be used for power supply, and
dedicated hybrid optical-electrical optical modules are required. Hybrid cables
need to be prepared and routed onsite. For details about how to prepare
hybrid cables, see 3.8.7 Assembling Second-Generation Hybrid Cable.
● If optical fibers need to be used, industrial optical modules are required.

Tools and Accessories

NOTE

All figures are for illustration purposes only and may not accurately depict actual devices or
modules.
● ESD wrist strap or ESD gloves
● Phillips screwdriver
● Flat-head screwdriver

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 31

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

● M3 screws (four)
● DIN mounting kit
● DIN rail (prepared by the customer)

Procedure
Step 1 Wear an ESD wrist strap. Ensure that one end of the ESD wrist strap is grounded
and the other end is in close contact with your wrist.
Step 2 Use a Phillips screwdriver to secure the DIN mounting kit to the rear of the remote
unit with four M3 screws.
NOTE

Ensure that the arrow on the DIN mounting kit points upwards.

Figure 2-24 Securing the remote unit to the DIN mounting kit

Step 3 Position the rear panel of the remote unit in front of the DIN rail, and attach the
remote unit to the DIN rail by locking the spring-loaded latch bolt into place.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 32

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Figure 2-25 Installing the remote unit on a DIN rail

Step 4 Insert an optical module into an optical port on the remote unit and connect an
optical fiber or a hybrid cable to the optical module.

Figure 2-26 Connecting a hybrid cable

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 33

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Figure 2-27 Connecting optical fibers

Step 5 Insert a Phoenix connector into the power input port on the remote unit, and
tighten the screws clockwise using a flat-head screwdriver.
Step 6 Connect one end of a ground cable to the ground screw on the right of the
remote unit, and connect the other end to the ground point or ground bar.
NOTE

If multiple remote units are installed, ensure that the distance between every two remote
units is at least 10 cm.

----End

2.4 Component Replacement

2.4.1 Replacing a Remote Unit

Context
A remote unit is severely damaged or a hardware fault occurs due to external
forces.

NOTICE

● Power off the remote unit before replacing it, which will interrupt services.
● Do not remove the remote unit immediately after it is powered off. Instead,
remove the remote unit after it cools down completely. When removing the
remote unit, touch the plastic part on the front of the remote unit and do not
touch the metal part on the rear of the remote unit. Otherwise, your fingers
may be burned.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 34

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver

Procedure
1. Wear an ESD wrist strap or ESD gloves. If you wear an ESD wrist strap, ensure
that one end of the ESD wrist strap is grounded and the other end is in close
contact with your wrist.
2. Ensure that the names, models, and specifications of the new and original
remote units are the same. If a mismatch is found, contact technical support
as soon as possible.
3. Record the IDs of slots where different modules are installed and cable
connections on ports of the original remote unit.
4. Power off the original remote unit.

CAUTION

The remote unit is successfully powered off when all indicators are off.

5. Replace the remote unit.

– If the remote unit is installed on a rapid duct:
i. Remove the cover plate to reserve sufficient space for operations,
and then remove the decorative panel.
ii. Remove the remote unit from the duct slot.
iii. Remove all cables and pluggable modules from the remote unit.
(You also need to remove the mechanical part if the remote unit is
installed on a rapid OBO80 duct.)
iv. Install the new remote unit in the original position.
– If the remote unit is installed on a workbench or wall:
i. Remove all cables and pluggable modules from the remote unit.
ii. Remove the remote unit from the wall-mounting screws. (Skip this
step if the remote unit is installed on a workbench.)

CAUTION

During the replacement, hold the bottom of the remote unit with
your hands to prevent it from falling down, which may cause
personal injury or damage to other devices.

iii. Install the new remote unit in the original position.

6. Install the original modules and cables according to the recorded information.
7. Power on the remote unit and observe the SYS indicator. Normally, the SYS
indicator on the remote unit is steady green.
8. Log in to the central switch and check whether the new remote unit is
working properly.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 35

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 2 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Remote Unit)

a. Run the display remote-unit connect record command to check the

logout record of the original remote unit and login record of the new
remote unit.
b. Run the display remote-unit command to check the remote unit
information. In the command output, the ESN field displays the ESN of
the new remote unit, and entries of the original remote unit have been
deleted.

Follow-up Procedure
If the new remote unit cannot work normally, contact the equipment supplier or
local maintenance personnel to obtain technical support.
After the replacement is complete, collect all tools. When you confirm that the
replaced remote unit is faulty, fill in the Repair Transmission Sheet and send the
faulty remote unit and the sheet to the equipment supplier or the specified repair
service provider.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 36

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

3 Hardware Installation and Component

Replacement (Fixed Switches)

3.1 Switch Overview

3.2 Installation Overview
3.3 Preparing for Installation
3.4 Unpacking a Switch
3.5 Installing a Switch
3.6 Installing Modules
3.7 Installing an HDF
3.8 Connecting a Switch
3.9 Post-installation Checks
3.10 (Optional) Installing an RPS1800
3.11 Powering on a Switch for the First Time
3.12 First Login to a Device
3.13 Component Replacement

3.1 Switch Overview

Huawei S series fixed switches ensure high-quality transmission of services and
provide reliable access and aggregation on campus networks. They have an
integrated hardware structure and consist of a chassis, power modules, fan
modules, and a Switch Control Unit (SCU). Some models support pluggable power
modules, fan modules, and cards.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 37

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

● All figures are for illustration purposes only and may not accurately depict the actual
device or module.
● Some switch models have nameplates attached on their bottom sides.
● The S5735-S4T2X-IA150G1, S5735-S8P2X-IA200G1, S5735-S8P2X-IA200H1, S5720I-6X-
PWH-SI-AC and S5720I-10X-PWH-SI-AC are outdoor fixed switches, which can be pole-
or wall-mounted. For details about how to install the switches, see the S5720I-6X-PWH-
SI-AC and S5720I-10X-PWH-SI-AC Quick Start Guide, S5735-S8P2X-IA200H1 Quick
Start Guide and S5735-S4T2X-IA150G1 and S5735-S8P2X-IA200G1 Quick Start Guide.

CAUTION

All switches except the S1730S-L8T-A and S1730S-L8T-MA are Class A products. In
a domestic environment, this product may cause radio interference in which case
the user may be required to take adequate measures.

The S series fixed switch models differ in appearance and basic dimensions
(excluding the parts protruding from the body).
Chassis basic dimensions determine where and how a switch can be installed. For
details, see 3.5.1 Installation Scenario Overview. For the dimensions of specific
switch models, see the Hardware Description.

3.2 Installation Overview

Figure 3-1 shows the sequence of tasks involved in installing a switch.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 38

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-1 Installation flowchart

3.3 Preparing for Installation

3.3.1 Safety Precautions

Before you start the installation procedure, read all safety precautions described in
this document and observe any warning labels affixed to the switch. Doing so
ensures your safety and protects the switch from damage.
Safety precautions provided in this document may not cover every eventuality, so
remain mindful of safety at all times.
Only trained and qualified personnel should be allowed to install, operate or
maintain the equipment.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 39

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

General Safety Guidelines

CAUTION

Always take precautions against ESD whenever you handle a switch. For example,
wear ESD gloves or an ESD wrist strap. To avoid electric shock or burn, remove
conductive objects like jewelry and watch.

WARNING

Connect the ground cable first after installing the switch into a cabinet or rack. Do
not remove the ground cable unless all the other cables and modules have been
removed from the chassis.

Environmental Safety

DANGER

Do not install the switch in an environment with flammable or explosive gases or

smoke.

NOTICE

Install the switch in a dry environment away from sources of water, as water or
damp may damage circuits of meters.

NOTICE

The installation site must be well ventilated to prevent the switches from
overheating.

Electrical Safety

DANGER

Contact with high-voltage power can be fatal. Never touch uninsulated electrical
wires or terminals that have not been disconnected from their power source.

DANGER

Never install or remove the switch or power cables while the power is on.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 40

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

DANGER

To ensure personal and equipment safety, ground the switch before powering it
on.

Laser Safety

CAUTION

Never look directly into an optical module or the ends of optical fibers. Optical
modules and connected fibers emit laser radiation that can cause eye damage.

CAUTION

Cover fiber connectors with dust caps when they are not connected.

Mechanical Safety

CAUTION

Use safe lifting practices when moving the switch. Never attempt to lift objects
that are too heavy for one person to handle. Instead, seek help or use appropriate
tools.

CAUTION

Before installing the switch into or removing it from a cabinet, ensure there are no
objects that could fall from the cabinet and cause injury.

NOTICE

Do not drill unapproved holes into a cabinet, as doing so may impair its
electromagnetic shielding and damage the cables inside. In addition, drilling holes
produces metal shavings that may enter the cabinet and cause short circuits on
printed circuit boards (PCBs).

3.3.2 Checking the Installation Site

The S series fixed switches (except for the S5720I-SI and outdoor fixed switches)
must be installed in indoor equipment rooms with controllable temperature. The
S5720I-SI series switches can also be installed in outdoor cabinets. Table 3-1
describes the requirements for the installation site.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 41

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Table 3-1 Requirements for the installation site

Item Requirement

Cleanliness The installation site must be clean, dry, well ventilated,

and free from leaking or dripping water and dew.
There are holes on the surface of some switches. Take
protective measures to prevent insects, water, animal
excrement, or other foreign matter from entering the
switch through the holes.

Dust The installation site must not have an excessive amount of

dust. A buildup of dust may cause electrostatic discharge
on the chassis and impair electrical connections, which will
reduce the service life and may cause failure of the switch.

Temperature and The switch must be installed in a temperature-controlled

humidity environment where the temperature and humidity are
within specifications. For the operating temperature and
relative humidity ranges required for your switch, see the
Hardware Description. In environments where the relative
humidity exceeds 70%, use dehumidifiers or dehumidifying
air conditioners. For the models with forced heat
dissipation, the fan speed increases with the increase of
the operating temperature. In a constant-temperature
equipment room, the noise caused by the increase of the
ambient temperature can be effectively avoided.

Corrosive gases The installation site must be free from acidic, alkaline, or
corrosive gases.

Airflow clearance Leave at least 50 mm (2.0 in.) clearance around the switch
for heat dissipation. Do not install a switch with its air
intake vent facing or close to the air exhaust vent of other
devices.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 42

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Item Requirement

Service port surge ● If power and network cables of a switch need to be

protection routed outdoors, bury them underground or put them
in steel pipes to protect the switch from lightning
strikes.
● If the Ethernet cables connected to a device need to be
routed outside, surge protectors must be configured for
the corresponding ports.
● If the network ports on the S5720I-SI series switches
are connected to devices on a street pole, no surge
protector needs to be installed. If the network ports are
connected to devices on a tower, a network port surge
protector must be installed.
● To protect network ports from lightning, use 8-line
surge protectors or Huawei certified 4-line surge
protectors. Connect the IN ports to terminals and the
OUT ports to network ports of the switch.
● If fiber reinforcing ribs are used, ensure that they are
properly grounded to protect the switches from
lightning.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 43

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Item Requirement

Power supply When installing the S5720I-SI series switches in outdoor

surge protection cabinets, ensure that the following requirements are met:
● AC switch:
– If the 220 V mains supply is used, install a 20 kA
surge protector between the power port of the
switch and the mains.
– If power is supplied by an isolated inverter near the
outdoor cabinet, no surge protector needs to be
installed between the power port of the switch and
the inverter.
● DC switch: An isolated power supply must be used and
placed in the same outdoor cabinet as the switch. Surge
protection is required for the power input of the
outdoor cabinet. The surge protector, power supply, and
switch must be equipotential. The outdoor cabinet must
be properly grounded and the grounding impedance
must be less than or equal to 10 ohms. If a DC switch is
connected to the PAC-260WA-E or PAC240S56-CN
power module that is powered by the 220 V mains,
install a 20 kA surge protector between the power input
port of the PAC-260WA-E or PAC240S56-CN and the
mains.
The 20 kA surge protector and S5720I-SI switch can be
decoupled using 5-10 m power cables or decoupling
inductors. For details, see "WLA220W01-20kA Surge
Protector" in the S5700 Series Switches Hardware
Description.
In all installation scenarios, switches, cabinets,
independent power modules, and surge protectors must be
separately grounded.

3.3.3 Checking the Cabinet or Rack

Table 3-2 describes the requirements for the cabinet or rack where a switch will
be installed in indoor equipment rooms.

Table 3-2 Requirements for the cabinet or rack

Item Requirement

Width The S series fixed switches have standard dimensions and

can be installed in a standard 19-inch cabinet or rack
(such as an N66E or N68E cabinet).

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 44

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Item Requirement

Depth If you use a non-standard cabinet or rack, ensure that

there is a sufficient space.
When equipped with 1150 W PoE power modules, the
switch cannot be installed in a 600 mm (23.6 in.) deep
cabinet.
Only switches whose depth is less than or equal to 220
mm and whose power outlets are on the front panel can
be installed in a 300 mm deep cabinet.

Distance between To install an S1730S-S48P4S-A, S5710-EI, S5710-HI, S5720

front and rear (420-mm deep models), S5730, S5731 (420-mm deep
mounting rails models), S5732 (420-mm deep models), S5735 (420-mm
deep models), S5736 (420-mm deep models), S6720 (420-
mm deep models), S6735 (420-mm deep models), or
S6730 (420-mm deep models) switch into a cabinet, install
front and rear mounting brackets on the switch. Ensure
that the distance between front and rear mounting rails is
within the specified range. For details, see 3.5.2.2 Using
Front and Rear Mounting Brackets and 3.5.2.3 Using
Front Mounting Brackets or Cable Management Frames
and Rear Mounting Brackets.
If the distance between front and rear mounting rails does
not meet the requirement, use a pair of guide rails or a
tray (purchased separately).

Grounding The cabinet or rack must have reliable ground points for
grounding the chassis.

Figure 3-2 shows the points from which to take measurements for the cabinet
width (a), the cabinet depth (b), and the distance between front and rear
mounting rails (c).

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 45

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-2 Measuring a cabinet

Table 3-3 describes the requirements for an outdoor cabinet where an S5720I-SI
series switch will be installed.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 46

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Table 3-3 Requirements for an outdoor cabinet

Item Requirements

Width of the The mounting rails supported by the standard mounting

mounting rails of brackets delivered with the S5720I-12X-SI-AC and
an outdoor cabinet S5720I-12X-PWH-SI-DC must have a width of 272.5 mm to
278.5 mm.
The mounting rails supported by the standard mounting
brackets delivered with the S5720I-28X-SI-AC and
S5720I-28X-PWH-SI-AC must have a width of 462 mm to
468 mm and support switch installation in a 19-inch
standard cabinet.
Installation of the 5720I-12X-SI-AC and S5720I-12X-PWH-
SI-DC in a 19-inch cabinet requires front mounting
brackets (part number: 21240477), which can be
purchased separately.

Installation space Ensure that the outdoor cabinet has sufficient installation
space and its depth is not less than that of the switch. In
addition, pay attention to the following:
● If G.657.A2 short-jacket optical fibers are used, the
distance between the front panel of the switch and the
front door of the cabinet must be at least 55 mm.
● If G.652 long-jacket optical fibers are used, the distance
between the front panel of the switch and the front
door of the cabinet must be at least 85 mm.
● Leave at least 50 mm (2.0 in.) clearance around the
switch for heat dissipation. Do not install a switch with
its air intake vent facing or close to the air exhaust vent
of other devices.

Grounding The cabinet must have reliable ground points for

grounding the chassis.

3.3.4 Checking the Power Supply System

The power supply system must be ready before the installation. Table 3-4
describes the requirements for the power supply system of the S series fixed
switches.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 47

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Table 3-4 Power supply requirements

Item Requirement

Input voltage The input voltage must be within switch specifications. For
details, see the Hardware Description.
Ensure that the power supply voltage of the device is
stable to prevent device failures caused by power grid
fluctuation.

Power outlets and ● To use AC power outlets, switches must have built-in AC
power cables power supply units or pluggable AC power modules,
and use AC power cables or AC power adapters
complying with local standards.
● To use an AC power distribution unit (PDU), switches
must have built-in AC power supply units or pluggable
AC power modules, and use C13 straight female to C14
straight male power cables.
● To use a DC power distribution box, switches must have
built-in DC power supply units or pluggable DC power
modules, and use DC power cables.
● The power cables and plugs delivered with a switch are
for use with this switch only. Do not use them on other
devices.

Circuit breaker of The rated current of a circuit breaker must be greater than
each channel the maximum input current of power modules.

3.3.5 Preparing Installation Tools and Accessories

Table 3-5 and Table 3-6 show the tools and accessories required for installing a
switch.

Table 3-5 Installation tools

Tool Description Picture

ESD wrist Used to

strap prevent
electrostatic
discharge.
Wear the
strap on your
wrist and
insert the cord
into the ESD
jack on the
cabinet.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 48

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Tool Description Picture

ESD gloves Used to

prevent
electrostatic
discharge.

Protective Used to
gloves protect hands
against
lacerations
and abrasions.

Utility knife Used to cut

open cartons.

Measuring Used to
tape measure
distance.

Marker Used to mark

the
installation
position of
components.

Flat-head Used to turn

screwdriver slotted-head
screws and
bolts.

Phillips Used to turn

screwdriver cross-head
screws and
bolts.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 49

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Tool Description Picture

Diagonal Used to cut

pliers insulation
tubes and
cables.

Network Used to test

cable tester the
connectivity
of network
cables.

Multimeter Used to test

the electrical
characteristics,
such as
voltage,
current, and
resistance, of
the switch,
cabinet, and
cables.

Hammer Used to drill

drill holes with
appropriately
sized drill bits
(selected
based on
depth of holes
and type of
expansion
bolts).

Adjustable Used to turn

wrench hex or square
bolts and
nuts.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 50

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Table 3-6 Installation accessories

Accessory Description Picture

Cable tie Used to

bundle cables.

Fiber Used to
binding bundle optical
tape fibers.

Insulation Used to
tape insulate
power wires
or other
conductors.

Corrugated Used to
pipe protect optical
fibers.

3.4 Unpacking a Switch

Context
A switch and its cables, cards, and power modules usually ship in cartons. This
section describes how to unpack a 442.0 mm x 220.0 mm x 43.6 mm (17.4 in. x
8.7 in. x 1.72 in.) switch model. The methods for unpacking switch models of other
dimensions or other components are similar.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 51

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

● Before opening the package, check whether the seal label or package is damaged. If
there are signs of damage, stop unpacking and contact the supplier.
● Moving an unpacked switch over a long distance may damage the switch. Do not
unpack the switch until you are ready to begin installation.
● Save the carton and packing material in case of future transportation.

Tools
● Protective gloves
● Utility knife

Procedure
Step 1 Wear protective gloves to protect your hands.
Step 2 Check the label on the carton to confirm whether the switch model is correct.

Step 3 Use a utility knife to cut the adhesive tape around the cover of the carton.

Step 4 Open the carton and take out the installation accessory package and the
Documentation Roadmap and Qualification Card.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 52

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

The Documentation Roadmap and Qualification Card or Quick Start Guide manual may be
included in the installation accessory package or packaged independently.

Step 5 Take the switch out of the carton and remove the foam packing materials.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 53

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 6 Take the switch out of the bag and check switch surfaces and the warranty seal on
the switch. If the switch is found eroded or damp or if the warranty seal is
damaged, stop unpacking and contact the supplier.

NOTE

Huawei is unable to provide warranty services if the warranty seal is damaged or removed.

Step 7 Check whether the nameplate on the chassis is consistent with the label on the
carton. The nameplate is attached to either the top or bottom of the chassis.

----End

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 54

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Follow-up Procedure
Save the installation accessory package for later use. The installation accessory
package contains the following items: mounting brackets, screws, rubber pads,
Phoenix connectors, and dust plugs.

NOTE

The type and quantity of items in an installation accessory package vary depending on the
product model.

3.5 Installing a Switch

3.5.1 Installation Scenario Overview

The S series fixed switches of different sizes support different installation
scenarios.

Table 3-7 Installation scenarios for S200&S300&S500 switches

Dimensions (H x Scenario: Scenario: Desk Scenario: Wall
W x D) Cabinet/Rack Mounting Mounting
Mounting

43.6 mm x 250.0 Supported Supported Supported

mm x 180.0 mm
(1.72 in. x 9.8 in. x
7.1 in.)

43.6 mm x 300.0 Supported Supported Supported

mm x 220.0 mm
(1.72 in. x 11.8 in.
x 8.7 in.)

43.6 mm x 442.0 Supported Supported Supported

mm x 220.0 mm
(1.72 in. x 17.4 in.
x 8.7 in.)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 55

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Table 3-8 Installation scenarios for S1700 switches

Switch Scenario: Scenario: Desk Scenario: Scenario:
Dimensions (H Cabinet/ Mounting Wall Network
x W x D) Rack Mounting Box
Mounting Mountin
g

29 mm x 230.0 Not Not supported Not Supporte

mm x 49.5 mm supported supported d
(1.14 in. x 9.06
in. x 1.95 in.)

28 mm x 160.0 Not Supported Supported Not

mm x 120.0 mm supported supported
(1.10 in. x 6.30
in. x 4.73 in.)

32.8 mm x 160.0 Not Supported Supported Not

mm x 134.0 mm supported supported
(1.29 in. x 6.30
in. x 5.28 in.)

43.6 mm x 250.0 Supported Supported Supported Not

mm x 180.0 mm Use front supported
(1.72 in. x 9.85 mounting
in. x 7.10 in.) brackets.

43.6 mm x 300.0 Supported Supported Supported Not

mm x 220.0 mm Use front supported
(1.72 in. x 11.82 mounting
in. x 8.67 in.) brackets.

43.6 mm x 320.0 Supported Supported Supported Not

mm x 208.0 mm Use front supported
(1.72 in. x 12.61 mounting
in. x 8.20 in.) brackets.

43.6 mm x 320.0 Supported Supported Supported Not

mm x 220.0 mm Use front supported
(1.72 in. x 12.61 mounting
in. x 8.67 in.) brackets.

43.6 mm x 442.0 Supported Supported Supported Not

mm x 220.0 mm Use front supported
(1.72 in. x 17.41 mounting
in. x 8.67 in.) brackets.

43.6 mm x 442.0 Supported Supported Supported Not

mm x 224.8 mm Use front supported
(1.72 in. x 17.41 mounting
in. x 8.86 in.) brackets.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 56

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Switch Scenario: Scenario: Desk Scenario: Scenario:

Dimensions (H Cabinet/ Mounting Wall Network
x W x D) Rack Mounting Box
Mounting Mountin
g

43.6 mm x 442.0 Supported Supported Supported Not

mm x 225.0 mm Use front supported
(1.72 in. x 17.41 mounting
in. x 8.87 in.) brackets.

43.6 mm x 442.0 Supported Supported Supported Not

mm x 314.8 mm Use front supported
(1.72 in. x 17.41 mounting
in. x 12.40 in.) brackets.

43.6 mm x 442.0 Supported Supported Not Not

mm x 420.0 mm Use front supported supported
(1.72 in. x 17.41 and rear
in. x 16.55 in.) mounting
brackets.

Table 3-9 Installation scenarios for S2700 switches

Switch Scenario: Scenario: Desk Scenario: Wall
Dimensions (H x Cabinet/Rack Mounting Mounting
W x D) Mounting

43.6 mm x 250.0 Supported Supported Supported

mm x 180.0 mm Use front
(1.72 in. x 9.8 in. x mounting
7.1 in.) brackets.

43.6 mm x 320.0 Supported Supported Supported

mm x 220.0 mm Use front
(1.72 in. x 12.6 in. mounting
x 8.7 in.) brackets.

43.6 mm x 300.0 Supported Supported Supported

mm x 220.0 mm Use front
(1.72 in. x 11.8 in. mounting
x 8.7 in.) brackets.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 57

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Switch Scenario: Scenario: Desk Scenario: Wall

Dimensions (H x Cabinet/Rack Mounting Mounting
W x D) Mounting

43.6 mm x 442.0 Supported Supported Supported

mm x 220.0 mm Use front
(1.72 in. x 17.4 in. mounting
x 8.7 in.) brackets.
The installation
methods of 224.8
mm deep devices
are the same. This
document uses
220.0 mm as an
example.

43.6 mm x 442.0 Supported Supported Supported

mm x 310.0 mm Use front
(1.72 in. x 17.4 in. mounting
x 12.2 in.) brackets.
The installation
methods of 314.8
mm deep devices
are the same. This
document uses
310.0 mm as an
example.

43.6 mm x 442.0 Supported Supported Not supported

mm x 420.0 mm Use front
(1.72 in. x 17.4 in. mounting
x 16.5 in.) brackets.

Table 3-10 Installation scenarios for S3700 switches

Dimensions (H x Scenario: Scenario: Desk Scenario: Wall
W x D) Cabinet/Rack Mounting Mounting
Mounting

43.6 mm x 442.0 Supported Supported Supported

mm x 220.0 mm Use front
(1.72 in. x 17.4 in. mounting
x 8.7 in.) brackets.

44.4 mm x 442.0 Supported Supported Not supported

mm x 220.0 mm Use front
(1.75 in. x 17.4 in. mounting
x 8.7 in.) brackets.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 58

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Dimensions (H x Scenario: Scenario: Desk Scenario: Wall

W x D) Cabinet/Rack Mounting Mounting
Mounting

43.6 mm x 442.0 Supported Supported Not supported

mm x 420.0 mm Use front
(1.72 in. x 17.4 in. mounting
x 16.5 in.) brackets.

Table 3-11 Installation scenarios for S5700 switches

Dimensions Scenario: Scenario: Scenario: Scenario: Scenario:
(H x W x D) Cabinet/ Desk Wall Top Wall DIN Rail
Rack Mounting Mountin Mountin Mountin
Mounting g g g

150.0 mm x Supported Not Not Not Supporte

46.0 mm x Use supported supported supported d
133.0 mm horizontal
(5.9 in. x rack-
1.81 in. x mounting
5.24 in.) kit.

150.0 mm x Supported Not Not Not Supporte

86.0 mm x Use supported supported supported d
133.0 mm horizontal
(5.9 in. x rack-
3.39 in. x mounting
5.24 in.) kit.

43.6 mm x Supported Supported Supported Not Not

250.0 mm x Use front supported supporte
180.0 mm mounting d
(1.72 in. x brackets.
9.8 in. x 7.1
in.)

43.6 mm x Supported Supported Supported Not Not

320.0 mm x Use front supported supporte
220.0 mm mounting d
(1.72 in. x brackets.
12.6 in. x 8.7
in.)

43.6 mm x Supported Supported Supported Not Not

320.0 mm x Use front supported supporte
210.0 mm mounting d
(1.72 in. x brackets.
12.6 in. x
8.27 in.)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 59

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Dimensions Scenario: Scenario: Scenario: Scenario: Scenario:

(H x W x D) Cabinet/ Desk Wall Top Wall DIN Rail
Rack Mounting Mountin Mountin Mountin
Mounting g g g

43.6 mm x Supported Supported Supported Supported Not

320.0 mm x Use front supporte
263.0 mm mounting d
(1.72 in. x brackets.
12.6 in. x
10.35 in.)

43.6 mm x Supported Supported Supported Not Not

300.0 mm x Use front supported supporte
220.0 mm mounting d
(1.72 in. x brackets.
11.8 in. x 8.7
in.)

43.6 mm x Supported Supported Supported Not Not

442.0 mm x Use front supported supporte
220.0 mm mounting d
(1.72 in. x brackets.
17.4 in. x 8.7
in.)
The
installation
methods for
devices with
a depth
ranging
from 220.0
mm to 227.0
mm are the
same. This
document
uses 220.0
mm as an
example.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 60

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Dimensions Scenario: Scenario: Scenario: Scenario: Scenario:

(H x W x D) Cabinet/ Desk Wall Top Wall DIN Rail
Rack Mounting Mountin Mountin Mountin
Mounting g g g

44.4 mm x Supported Supported Not Not Not

442.0 mm x Use front supported supported supporte
220.0 mm mounting d
(1.75 in. x brackets.
17.4 in. x 8.7
in.)
The
installation
methods for
devices with
a depth
ranging
from 220.0
mm to 224.9
mm are the
same. This
document
uses 220.0
mm as an
example.

43.6 mm x Supported Supported Supported Not Not

442.0 mm x Use front supported supporte
260.0 mm mounting d
(1.72 in. x brackets.
17.40 in. x
10.24 in.)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 61

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Dimensions Scenario: Scenario: Scenario: Scenario: Scenario:

(H x W x D) Cabinet/ Desk Wall Top Wall DIN Rail
Rack Mounting Mountin Mountin Mountin
Mounting g g g

43.6 mm x Supported Supported Supported Not Not

442.0 mm x Use front supported supporte
310.0 mm mounting d
(1.72 in. x brackets.
17.4 in. x
12.2 in.)
The
installation
methods for
devices with
a depth
ranging
from 310.0
mm to 314.9
mm are the
same. This
document
uses 310.0
mm as an
example.

43.6 mm x Supported Supported Not Not Not

442.0 mm x ● S5700-SI supported supported supporte
420.0 mm and d
(1.72 in. x S5700-EI:
17.4 in. x use front
16.5 in.) mounting
brackets
● Other
models:
use front
and rear
mounting
brackets

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 62

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Dimensions Scenario: Scenario: Scenario: Scenario: Scenario:

(H x W x D) Cabinet/ Desk Wall Top Wall DIN Rail
Rack Mounting Mountin Mountin Mountin
Mounting g g g

44.4 mm x Supported Supported Not Not Not

442.0 mm x Use front supported supported supporte
420.0 mm and rear d
(1.75 in. x mounting
17.4 in. x brackets.
16.5 in.)
The
installation
methods of
the devices
whose depth
ranges from
420.0 mm to
510.5 mm
are the
same. This
document
uses 420.0
mm as an
example.

86.1 mm x Supported Not Not Not Not

442.0 mm x Use front supported supported supported supporte
470.0 mm mounting d
(3.4 in. x brackets or
17.4 in. x cable
18.5 in.) managemen
t frames and
rear
mounting
brackets.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 63

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Table 3-12 Installation scenarios for S6700 switches

Dimensions (H x Scenario: Scenario: Desk Scenario: Wall
W x D) Cabinet/Rack Mounting Mounting
Mounting

43.6 mm x 442.0 Supported ● S6700-EI and Not supported

mm x 420.0 mm ● S6700-EI: use S6720-HI: Not
(1.72 in. x 17.4 in. front mounting supported
x 16.5 in.) brackets ● Other models:
● Other models: Supported
use front and
rear mounting
brackets
NOTE
Using guide rails
(purchased
separately) to
support the S6700-
EI is recommended
due to its weight.

44.4 mm x 442.0 Supported Supported Not supported

mm x 420.0 mm
(1.75 in. x 17.4 in.
x 16.5 in.)
The installation
methods of the
devices whose
depth ranges
from 420.0 mm to
425.0 mm are the
same. This
document uses
420.0 mm as an
example.

44.4 mm x 442.0 Supported Supported Not supported

mm x 220.0 mm
(1.75 in. x 17.4 in.
x 8.7 in.)
The installation
methods for
devices with a
depth ranging
from 220.0 mm to
225.0 mm are the
same. This
document uses
220.0 mm as an
example.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 64

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Dimensions (H x Scenario: Scenario: Desk Scenario: Wall

W x D) Cabinet/Rack Mounting Mounting
Mounting

43.6 mm x 442.0 Supported Supported Supported

mm x 220.0 mm
(1.72 in. x 17.4 in.
x 8.7 in.)

NOTE

For the S5735-L, S5735S-L, and S5735S-L-M series switches with natural heat dissipation,
heat is dissipated from the bottom shell, leading to a high temperature of the shell even at
ambient temperature. To prevent injuries, do not touch the bottom shell. Additionally, you
must install these switches in a well-ventilated area with restricted access (not accessible to
unskilled personnel), instead of on a desk or in an airtight cabinet. It is recommended that
the switches be installed in a well-ventilated network box or cabinet.

3.5.2 Scenario : Cabinet/Rack Mounting

3.5.2.1 Using Front Mounting Brackets

Context
This installation method applies to the following switches:
● S1700 (excluding the S1700-8-AC and S1700-8G-AC), S1720, and S1730S
(excluding the S1730S-L4P1T-BUA, S1730S-L8P2T-BUA, S1730S-L8LP2T-BUA,
S1730S-L8T-A, S1730S-L8T-MA, and S1730S-S48P4S-A)
● All S2700 series
● All S3700 series
● Some S5700 models:
– S5700-LI, S5700S-LI, S5710-LI, S5720-LI, S5720S-LI, S5700-SI, S5720-SI
(except 420-mm deep models), S5720S-SI, S5700-EI, S5720-EI (except
420-mm deep models), S5700-HI, S5720I-12X-SI-AC, S5720I-12X-PWH-SI-
DC, S5720I-28X-SI-AC, S5720I-28X-PWH-SI-AC, S5731-S (except 420-mm
deep models), S5731S-S (except 420-mm deep models), S5736-S (except
420-mm deep models), S5735-L (except 420-mm deep models), S5735S-L
(except 420-mm deep models), S5735-L1, S5735S-L1, S5735-L-I, S5735S-
L-M, S5731-L16P2SR-RUA, and S5731S-L16P2SR-RUA
– S5735-L-V2 (except 420-mm deep models) and S5735I-L-V2
● Some S6700 models, including the S6700-EI, S6720S-EI, S6720-LI, S6720S-LI,
and S6730-H (except 420-mm deep models)
● All S200 series
● All S300 series
● All S500 series
Follow these precautions before or during the installation:

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 65

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

● Ensure that the cabinet is stable and meets the requirements specified in 3.3.3
Checking the Cabinet or Rack.
● Leave sufficient vertical space in the cabinet or rack for the switch.
● Leave at least 50 mm (2.0 in.) clearance around the switch for heat
dissipation. Do not install a switch with its air intake vent facing or close to
the air exhaust vent of other devices.
● To install multiple switches in one cabinet or rack, leave at least 1 U (1 U =
44.45 mm) between switches that use natural heat dissipation. For switches
that use forced or intelligent air cooling, the recommended spacing between
them is 1 U.
● Align the mounting brackets on the left and right mounting rails. If they are
not on a horizontal line, forcibly mounting the switch may distort the chassis.
● For an S6700-EI switch, using guide rails (purchased separately) to support
the chassis is recommended.
● The S5720I-12X-SI-AC, S5720I-12X-PWH-SI-DC, S5720I-28X-SI-AC, and
S5720I-28X-PWH-SI-AC switches can also be installed in outdoor cabinets. The
installation method and requirements are the same as those in the indoor
cabinets.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver
● Flat-head screwdriver
● Floating nuts (four per switch, purchased separately)
● M4 screws (The quantity depends on the switch. See Figure 3-3.)
● M6 screws (four per switch, purchased separately)
● Front mounting brackets (two per switch)
● Ground cable
● Guide rails (optional)
NOTE

The M4 screws and front mounting brackets are included in the installation accessory
package.
When installing mounting ears, use screws of the same specifications as those configured
by the manufacturer. Do not use screws that are too long to prevent damage to the device.

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.

Step 2 Use M4 screws to attach a front mounting bracket delivered with the switch to
each side of the switch. Figure 3-3 shows the front mounting brackets delivered
with different switch models and associated installation methods.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 66

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

● To install a 250 mm x 180 mm (9.8 in. x 7.1 in. W x D) switch in a 19-inch cabinet, use
the front mounting brackets shown in c of Figure 3-3 (some models need purchased
separately, part number of 21240477).
● To install a 220 mm (8.7 in.) deep switch in a 21-inch cabinet, install the front mounting
brackets according to g of Figure 3-3.
● See Figure 3-3 for the number of screws required for each mounting bracket.
● When installing mounting ear j, pay attention to the R/L label on the mounting ear. The
mounting ear labeled R is installed on the right side of the device, and the mounting ear
labeled L is installed on the left side of the device. In addition, the mounting ear marked
with R has a ground hole for connecting a ground cable to provide the grounding
function.

Figure 3-3 Installing front mounting brackets

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 67

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-4 Spacing of mounting holes for different mounting ears

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 68

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 3 Connect the ground cable to the switch. For details, see step 2 and step 3 in 3.5.8
Connecting the Ground Cable.
NOTE

This step is optional. For switch models with the ground point at the left or right side of the
chassis, connect the ground cable before mounting the switch in the cabinet or rack.

Step 4 Install floating nuts on the mounting rails of the cabinet.

Determine the installation position of the switch and use a flat-head screwdriver
to install two floating nuts on each front mounting rail accordingly. Leave a gap of
one mounting hole between the two floating nuts and ensure that they are level
with those on the other rail.

NOTE

Pay attention to the scale markings on the mounting rails because three adjacent mounting
holes may not be 1 U.

Step 5 Install the switch in the cabinet. The methods for installing switches that use
different front mounting brackets are the same. Figure 3-5 shows an example.
1. Hold the bottom of the switch and align the holes on the front mounting
brackets with the floating nuts on the front mounting rails.
2. Secure the mounting brackets to the mounting rails with M6 screws (two on
each side) using a Phillips screwdriver.

Figure 3-5 Installing the switch in the cabinet

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 69

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

----End

3.5.2.2 Using Front and Rear Mounting Brackets

Context
This installation method applies to the following switches:
● S1730S-S48P4S-A
● Some S5700 models:
– S5710-EI, S5720-SI (420-mm deep models), S5720-EI (420-mm deep
models), S5720-HI, S5730-SI, S5730S-EI, S5730-HI, S5731-H, S5731-S
(420-mm deep models), S5731S-S (420-mm deep models), S5731S-H,
S5732-H, S5735-L (420-mm deep models), S5735S-L (420-mm deep
models), S5735-S, S5735S-H, S5736-S, and S5735S-S
– S5732-H-V2, S5735-L-V2 (420-mm deep models), S5735-S-V2, and
S5735I-S-V2 (420-mm deep models)
● Some S6700 models:
– S6720-SI, S6720S-SI, S6720-EI, S6720-HI, S6730-H (420-mm deep
models), S6730S-H, S6730-S, S6735-S, and S6730S-S
– S6732-H-V2

Follow these precautions before or during the installation:

● Ensure that the cabinet is stable and meets the requirements specified in 3.3.3
Checking the Cabinet or Rack.
● Leave sufficient vertical space in the cabinet or rack for the switch.
● Leave at least 50 mm (2.0 in.) clearance around the switch for heat
dissipation. Do not install a switch with its air intake vent facing or close to
the air exhaust vent of other devices.
● To install multiple switches in one cabinet or rack, leave at least 1 U (1 U =
44.45 mm) between switches that use natural heat dissipation. For switches
that use forced or intelligent air cooling, the recommended spacing between
them is 1 U.
● Align the mounting brackets on the left and right mounting rails. If they are
not on a horizontal line, forcibly mounting the switch may distort the chassis.
● If guide rails are installed in the cabinet, install only front mounting brackets
on the switch.
● The distance data provided in this section is calculated theoretically and does
not include tolerances.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver
● Flat-head screwdriver
● Measuring tape

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 70

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

● Floating nuts (eight per switch, purchased separately)

● M4 screws (eight or fourteen per switch)
● M6 screws (eight per switch, purchased separately)
● Front mounting brackets (two per switch)
● Rear mounting brackets (two per switch)
● Rear mounting bracket guide rails (two per switch)
NOTE

The M4 screws, front and rear mounting brackets, and rear mounting bracket guide rails
are included in the installation accessory package.
When installing mounting ears, use screws of the same specifications as those configured
by the manufacturer. Do not use screws that are too long to prevent damage to the device.

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.

Step 2 Use a measuring tape to measure the distance between the front and rear
mounting rails in the cabinet.

Step 3 Select front mounting brackets, rear mounting brackets, and rear mounting
bracket guide rails based on the distance between the front and rear mounting
rails in the cabinet. Use M4 screws to attach front and rear mounting brackets to
each side of the switch.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 71

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

● Applicable to the S5710-EI, S5720-SI (420-mm deep models), S5720-EI

(420-mm deep models), S5720-HI, S5730-SI, S5730S-EI, S5730-HI, S6720-
SI, S6720S-SI, and S6720-EI:

Table 3-13 Front mounting brackets, rear mounting brackets, and rear
mounting bracket guide rails (1)
Front Mounting Bracket, Remarks
Rear Mounting Bracket,
and Rear Mounting
Bracket Guide Rail

Standard front mounting bracket, rear

mounting bracket, and rear mounting bracket
guide rail

Standard front mounting bracket, and custom

rear mounting bracket and rear mounting
bracket guide rail (part number: 21240538)

Standard front mounting bracket, and custom

rear mounting bracket and rear mounting
bracket guide rail (part number: 21240537)

The distance between the front and rear mounting rails in the cabinet
determines the installation position of front mounting brackets, rear
mounting brackets, and rear mounting bracket guide rails. See Table 3-14.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 72

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Table 3-14 Installation of the front mounting brackets, rear mounting

brackets, and rear mounting bracket guide rails (1)
Distance Installation of the Front Remarks
Between Mounting Bracket, Rear
Front and Mounting Bracket, and
Rear Rear Mounting Bracket
Mounting Guide Rail
Rails

335-380 Use standard mounting

mm brackets.
(13.2-15.0 If the distance between the
in.) front and rear mounting rails
is 335-365 mm (13.2-14.4
in.), you can only install the
front mounting brackets in
the opposite direction (see
figure). In this installation
mode, the front panel of a
switch protrudes from the
mounting rails of the cabinet
51 mm (2.0 in.). Ensure that
there is enough space
between the front panel of
the switch and the front
cabinet door for cabling.

365-415 Use standard mounting

mm brackets.
(14.4-16.3 Install front mounting
in.) brackets in the normal
direction (see figure). In this
installation mode, the front
panel of a switch protrudes
from the mounting rails of
the cabinet 19 mm (0.75 in.).
Ensure that there is enough
space between the front
panel of the switch and the
front cabinet door for
cabling.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 73

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Distance Installation of the Front Remarks

Between Mounting Bracket, Rear
Front and Mounting Bracket, and
Rear Rear Mounting Bracket
Mounting Guide Rail
Rails

378-442 Use standard mounting

mm brackets.
(14.9-17.4 Install front mounting
in.) brackets in the normal
direction (see figure). In this
installation mode, the front
panel of a switch protrudes
from the mounting rails of
the cabinet 19 mm (0.75 in.).
Ensure that there is enough
space between the front
panel of the switch and the
front cabinet door for
cabling.

442-460 Use custom mounting

mm brackets (part number:
(17.4-18.1 21240538).
in.) Install front mounting
brackets in the normal
direction (see figure). In this
installation mode, the front
panel of a switch protrudes
from the mounting rails of
the cabinet 19 mm (0.75 in.).
Ensure that there is enough
space between the front
panel of the switch and the
front cabinet door for
cabling.
Only custom rear mounting
brackets (part number:
21240538) can cover this
distance range. However,
there is a risk that the rear
mounting brackets protrude
from the mounting rails and
reach the rear door of the
cabinet.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 74

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Distance Installation of the Front Remarks

Between Mounting Bracket, Rear
Front and Mounting Bracket, and
Rear Rear Mounting Bracket
Mounting Guide Rail
Rails

460-510 Use standard mounting

mm brackets or custom mounting
(18.1-20.1 brackets (part number:
in.) 21240538).
If the distance between front
and rear mounting rails is
460-495 mm (18.1-19.5 in.):
– When standard mounting
brackets are used, you can
only install the front
mounting brackets in the
opposite direction (see
figure). In this installation
mode, the front panel of
a switch protrudes from
the mounting rails of the
cabinet 51 mm (2.0 in.).
Ensure that there is
enough space between
the front panel of the
switch and the front
cabinet door for cabling.
– When custom mounting
brackets (part number:
21240538) are used,
install front mounting
brackets in the normal
direction.

495-543 Use standard mounting

mm brackets.
(19.5-21.4 Install front mounting
in.) brackets in the normal
direction (see figure). In this
installation mode, the front
panel of a switch protrudes
from the mounting rails of
the cabinet 19 mm (0.75 in.).
Ensure that there is enough
space between the front
panel of the switch and the
front cabinet door for
cabling.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 75

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Distance Installation of the Front Remarks

Between Mounting Bracket, Rear
Front and Mounting Bracket, and
Rear Rear Mounting Bracket
Mounting Guide Rail
Rails

506-570 Use standard mounting

mm brackets.
(20.0-22.4 Install front mounting
in.) brackets in the normal
direction (see figure). In this
installation mode, the front
panel of a switch protrudes
from the mounting rails of
the cabinet 19 mm (0.75 in.).
Ensure that there is enough
space between the front
panel of the switch and the
front cabinet door for
cabling.

570-662 Use custom mounting

mm brackets (part number:
(22.4-26.1 21240538).
in.) Install front mounting
brackets in the normal
direction (see figure). In this
installation mode, the front
panel of a switch protrudes
from the mounting rails of
the cabinet 19 mm (0.75 in.).
Ensure that there is enough
space between the front
panel of the switch and the
front cabinet door for
cabling.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 76

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Distance Installation of the Front Remarks

Between Mounting Bracket, Rear
Front and Mounting Bracket, and
Rear Rear Mounting Bracket
Mounting Guide Rail
Rails

662-800 Use custom mounting

mm brackets (part number:
(26.1-31.5 21240537).
in.) If the distance between the
front and rear mounting rails
is 662-694 mm (26.1-27.3
in.), you can only install the
front mounting brackets in
the opposite direction (see
figure). In this installation
mode, the front panel of a
switch protrudes from the
mounting rails of the cabinet
51 mm (2.0 in.). Ensure that
there is enough space
between the front panel of
the switch and the front
cabinet door for cabling.

694-830 Use custom mounting

mm brackets (part number:
(27.3-32.7 21240537).
in.) Install front mounting
brackets in the normal
direction (see figure). In this
installation mode, the front
panel of a switch protrudes
from the mounting rails of
the cabinet 19 mm (0.75 in.).
Ensure that there is enough
space between the front
panel of the switch and the
front cabinet door for
cabling.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 77

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Distance Installation of the Front Remarks

Between Mounting Bracket, Rear
Front and Mounting Bracket, and
Rear Rear Mounting Bracket
Mounting Guide Rail
Rails

708-855 Use custom mounting

mm brackets (part number:
(27.9-33.7 21240537).
in.) Install front mounting
brackets in the normal
direction (see figure). In this
installation mode, the front
panel of a switch protrudes
from the mounting rails of
the cabinet 19 mm (0.75 in.).
Ensure that there is enough
space between the front
panel of the switch and the
front cabinet door for
cabling.

● Applicable to:
S1730S-S48P4S-A, S5731-H, S5731-S (420-mm deep models), S5731S-S
(420-mm deep models), S5731S-H, S5732-H, S5735-L (420-mm deep
models), S5735S-L (420-mm deep models), S5735-S, S5735S-S, S5735S-H,
S5736-S, S6730-S, S6730S-S, S6720-HI, S6730S-H, S6735-S, and S6730-H
(420-mm deep models)
S5732-H-V2, S5735-L-V2 (420-mm deep models), S5735-S-V2, S5735I-S-V2
(420-mm deep models), and S6732-H-V2

Table 3-15 Front mounting brackets, rear mounting brackets, and rear
mounting bracket guide rails (2)
Front Mounting Bracket, Rear Remarks
Mounting Bracket, and Rear
Mounting Bracket Guide Rail

Standard front mounting bracket,

rear mounting bracket, and rear
mounting bracket guide rail

Standard front mounting bracket,

and custom rear mounting bracket
and rear mounting bracket guide
rail (part number: 21240538)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 78

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Front Mounting Bracket, Rear Remarks

Mounting Bracket, and Rear
Mounting Bracket Guide Rail

Standard front mounting bracket,

and custom rear mounting bracket
and rear mounting bracket guide
rail (part number: 21240537)

The distance between the front and rear mounting rails in the cabinet
determines the installation position of front mounting brackets, rear
mounting brackets, and rear mounting bracket guide rails. See Table 3-16.

Table 3-16 Installation of the front mounting brackets, rear mounting

brackets, and rear mounting bracket guide rails (2)
Distance Installation of the Front Remarks
Between Mounting Bracket, Rear
Front and Mounting Bracket, and Rear
Rear Mounting Bracket Guide Rail
Mounting
Rails

310-351 Use standard mounting

mm brackets.
(12.2-13.8 You can only install the
in.) front mounting brackets in
the opposite direction (see
figure). In this installation
mode, the front panel of a
switch protrudes from the
mounting rails of the
cabinet 64 mm (2.5 in.).
Ensure that there is enough
space between the front
panel of the switch and the
front cabinet door for
cabling.

369-410 Use standard mounting

mm brackets.
(14.5-16.1 Install front mounting
in.) brackets in the normal
direction (see figure).

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 79

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Distance Installation of the Front Remarks

Between Mounting Bracket, Rear
Front and Mounting Bracket, and Rear
Rear Mounting Bracket Guide Rail
Mounting
Rails

438-479 Use standard mounting

mm brackets or custom
(17.2-18.9 mounting brackets (part
in.) number: 21240538).
– When standard mounting
brackets are used, you
can only install the front
mounting brackets in the
opposite direction (see
figure). In this
installation mode, the
front panel of a switch
protrudes from the
mounting rails of the
cabinet 64 mm (2.5 in.).
Ensure that there is
enough space between
the front panel of the
switch and the front
cabinet door for cabling.
– When custom mounting
brackets (part number:
21240538) are used,
install front mounting
brackets in the normal
direction and install rear
mounting bracket guide
rails in the opposite
direction.

497-538 Use standard mounting

mm brackets.
(19.6-21.2 Install front mounting
in.) brackets in the normal
direction (see figure).

539-637 Use custom mounting

mm brackets (part number:
(21.2-25.1 21240538).
in.) Install front mounting
brackets in the normal
direction (see figure).

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 80

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Distance Installation of the Front Remarks

Between Mounting Bracket, Rear
Front and Mounting Bracket, and Rear
Rear Mounting Bracket Guide Rail
Mounting
Rails

638-696 Use custom mounting

mm brackets (part number:
(25.1-27.4 21240537).
in.) You can only install the
front mounting brackets in
the opposite direction (see
figure). In this installation
mode, the front panel of a
switch protrudes from the
mounting rails of the
cabinet 64 mm (2.5 in.).
Ensure that there is enough
space between the front
panel of the switch and the
front cabinet door for
cabling.

697-835 Use custom mounting

mm brackets (part number:
(27.4-32.9 21240537).
in.) Install front mounting
brackets in the normal
direction (see figure).

NOTE

If the distance between the front and rear mounting rails in a cabinet is out of the ranges
listed in Table 3-14 and Table 3-16, use a tray together with the front mounting brackets.

Step 4 Connect the ground cable to the switch. For details, see step 2 and step 3 in 3.5.8
Connecting the Ground Cable.
NOTE

This step is optional. For switch models with the ground point at the left or right side of the
chassis, connect the ground cable before mounting the switch in the cabinet or rack.

Step 5 Install floating nuts on the mounting rails of the cabinet.

1. Determine the installation position of the switch and use a flat-head
screwdriver to install two floating nuts on each front mounting rail
accordingly. Leave a gap of 1 U between the two floating nuts and ensure
that they are level with those on the other front mounting rail.
2. Install two floating nuts on each rear mounting rail. Leave a gap of 1 U
between the two floating nuts. Ensure that the lower floating nuts on the
four mounting rails are level with one another.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 81

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 6 Install two rear mounting bracket guide rails on the rear mounting rails. The
distance between the front and rear mounting rails determines the direction in
which the guide rails should face. See Table 3-14 and Table 3-16.
1. Align the holes on the guide rails with the floating nuts on the rear mounting
rails.
2. Secure the guide rails to the mounting rails with M6 screws (two on each
side) using a Phillips screwdriver.

Figure 3-6 Installing rear mounting bracket guide rails (using the distance of
497-538 mm between front and rear mounting rails as an example)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 82

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-7 Installing rear mounting bracket guide rails (using the distance of
369-410 mm between front and rear mounting rails as an example)

Step 7 Install the switch in the cabinet. In Figure 3-8, the distance between front and
rear mounting rails is 497-538 mm.
1. Align the rear mounting brackets with the rear mounting bracket guide rails.
Then, gently slide the switch into the cabinet along the guide rails.
2. Align the holes on the front mounting brackets with the floating nuts on the
front mounting rails, and secure each mounting bracket with two M6 screws
using a Phillips screwdriver.

Figure 3-8 Installing the switch in the cabinet

----End

3.5.2.3 Using Front Mounting Brackets or Cable Management Frames and

Rear Mounting Brackets

Context
This installation method applies to S5710-HI switches.
Follow these precautions before or during the installation:

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 83

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

● Ensure that the cabinet is stable and meets the requirements specified in 3.3.3
Checking the Cabinet or Rack.
● Leave sufficient vertical space in the cabinet or rack for the switch.
● Leave at least 50 mm (2.0 in.) clearance around the switch for heat
dissipation. Do not install a switch with its air intake vent facing or close to
the air exhaust vent of other devices.
● To install multiple switches in one cabinet or rack, leave at least 1 U (1 U =
44.45 mm) between switches that use natural heat dissipation. For switches
that use forced or intelligent air cooling, the recommended spacing between
them is 1 U.
● Align the mounting brackets on the left and right mounting rails. If they are
not on a horizontal line, forcibly mounting the switch may distort the chassis.
● To install an S5710-HI switch, install front mounting brackets or cable
management frames and rear mounting brackets on the switch. If guide rails
are installed in the cabinet, install only front mounting brackets or cable
management frames on the switch.
● If all ports on the switch need to be used, many cables will be connected to
the switch. Cable management frames are recommended in this case.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver
● Flat-head screwdriver
● Measuring tape
● Floating nuts (eight per switch, purchased separately)
● M4 screws (sixteen per switch)
● M6 screws (eight per switch, purchased separately)
● Front mounting brackets or cable management frames (two per switch)
● Rear mounting brackets (two per switch)
● Rear mounting bracket guide rails (two per switch)
NOTE

The M4 screws, front and rear mounting brackets, cable management frames, and rear
mounting bracket guide rails are included in the installation accessory package.
When installing mounting ears, use screws of the same specifications as those configured
by the manufacturer. Do not use screws that are too long to prevent damage to the device.

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.

Step 2 Use M4 screws to attach front mounting brackets or cable management frames
and rear mounting brackets to the switch. Figure 3-9 and Figure 3-10 show the
mounting brackets and cable management frames of an S5710-HI and associated
installation methods.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 84

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-9 Installing front and rear mounting brackets

Figure 3-10 Installing cable management frames and rear mounting brackets

Step 3 Install floating nuts on the mounting rails of the cabinet. See Figure 3-11.
1. Determine the installation position of the switch and use a flat-head
screwdriver to install two floating nuts on each front mounting rail
accordingly. Leave a gap of 2 U between the two floating nuts and ensure
that they are level with those on the other front mounting rail.
2. Install two floating nuts on each rear mounting rail. Leave a gap of 1 U
between the two floating nuts. Ensure that the lower floating nuts on the
four mounting rails are level with one another.

Figure 3-11 Installing floating nuts

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 85

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 4 Use a measuring tape to measure the distance between the front and rear
mounting rails.

Step 5 Install two rear mounting bracket guide rails on the rear mounting rails. The
distance between the front and rear mounting rails determines the direction in
which the guide rails should face. See Figure 3-12 and Figure 3-13.
1. Align the holes on the guide rails with the floating nuts on the rear mounting
rails.
2. Secure the rear mounting bracket guide rails with M6 screws (two on each
side) using a Phillips screwdriver.

Figure 3-12 Installing rear mounting bracket guide rails (545-655 mm [21.5-25.8
in.] between front and rear mounting rails)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 86

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-13 Installing rear mounting bracket guide rails (418-528 mm [16.5-20.8
in.] between front and rear mounting rails)

Step 6 Install the switch in the cabinet.

● If you have installed front and rear mounting brackets on the switch, perform
the following steps:
a. Place M6 screws on the two lower floating nuts on the front mounting
rails. Reserve a clearance between the top of the screws and the floating
nuts for installing front mounting brackets.
b. Align the rear mounting brackets with the rear mounting bracket guide
rails. Then, gently slide the switch into the cabinet along the guide rails.
c. Align the holes on the front mounting brackets with floating nuts on the
front mounting rails, place the recesses at the bottom of the front
mounting brackets on the M6 screws, and then use a Phillips screwdriver
to tighten the M6 screws.
In Figure 3-14, the distance between front and rear mounting rails is 545-655
mm (21.5-25.8 in.).

Figure 3-14 Supporting the switch using front and rear mounting brackets

● If you have installed cable management frames and rear mounting brackets
on the switch, perform the following steps:

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 87

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

a. Align the rear mounting brackets with the rear mounting bracket guide
rails. Then, gently slide the switch into the cabinet along the guide rails.
b. Align the holes on the cable management frames with the floating nuts
on the front mounting rails, and secure the cable management frames
with M6 screws using a Phillips screwdriver.

NOTICE

Do not hold the cable management frames to move the switch as doing so
may damage the cable management frames.

In Figure 3-15, the distance between front and rear mounting rails is 545-655
mm (21.5-25.8 in.).

Figure 3-15 Supporting the switch using cable management frames and rear
mounting brackets

----End

3.5.2.4 Using Horizontal Rack-mounting Kit

Context
This installation method applies to the S5735I-S8T4SN-V2, S5735I-S8T4XN-V2,
S5735I-S8T4XN-T-V2, and S5735I-S8U4XN-V2.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 88

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTICE

When multiple S5735I-S8T4SN-V2 switches are installed on the same horizontal

rack-mounting kit, there must be a clearance of at least 88 mm between two
neighboring switches. The clearance above a switch must be at least two times
the switch's height and that below must be greater than or equal to the switch's
height.
When multiple S5735I-S8T4XN-V2, S5735I-S8T4XN-T-V2, and S5735I-S8U4XN-V2
switches are installed on the same horizontal rack-mounting kit, there must be a
clearance of at least 66 mm between two neighboring switches. The clearance
above a switch must be at least two times the switch's height and that below
must be greater than or equal to the switch's height.

Make sure the following prerequisites are met before the installation:
● The cabinet is well fixed.
● The switch installation position in the cabinet is determined and arranged
properly.
● The switch to be installed is available and located near the cabinet for
convenient movement.

Tools and Accessories

● Phillips screwdriver
● Flat-head screwdriver
● Floating nuts
● M6 screws
● Horizontal rack-mounting kit
NOTE

The horizontal rack-mounting kit (part number: 21241946), floating nuts, and M6 screws
are not included in the installation accessory package and needs to be purchased
separately.

Procedure
Step 1 Install two floating nuts on each front mounting rail of the cabinet. Leave four
mounting holes between the two floating nuts on the same mounting rail.
NOTE

● The length of six adjacent mounting holes may not be 2 U. Observe the scale ticks on
the mounting rails when installing floating nuts.
● You can use a flat-head screwdriver to install floating nuts.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 89

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 2 Attach the brackets of the horizontal rack-mounting kit on the front mounting
rails of the cabinet and insert M6 screws in the mounting holes. Use a Phillips
screwdriver to tighten the lower M6 screws and then the upper ones to fix the
rack-mounting kit.

Step 3 Place the rear panel of the switch in front of the DIN rail on the rack-mounting kit
and ensure that the DIN rail fits in between the fixture near the top of the switch
and the spring latch near the bottom.
Step 4 Make the switch incline forward with the bottom away from the DIN rail, and
place the fixture at the rear of the switch on the top of the DIN rail.
Step 5 Slowly push the switch toward the DIN rail to make the spring latch at the rear of
the switch move down. The spring latch then bounces back to fix the switch on
the DIN rail.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 90

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

If the spring latch is too tight to move down, you can use a flat-head screwdriver to hold down
the spring latch during the installation.
For details about how to install a switch on a DIN rail, see 3.5.7 Scenario: DIN Rail Mounting.

----End

3.5.3 Scenario: Desk Mounting

Context
This installation method applies to all fixed switches except the following models:

● S5710-HI, S6700-EI, and S6720-HI

● S5735I-S8T4SN-V2, S5735I-S8T4XN-V2, S5735I-S8T4XN-T-V2, and S5735I-
S8U4XN-V2
● S1730S-L4P1T-BUA, S1730S-L8LP2T-BUA, and S1730S-L8P2T-BUA

Follow these precautions:

● Ensure that the desk is flat, sturdy, and properly grounded.
● Leave at least 50 mm (2.0 in.) clearance around the switch for heat
dissipation. Do not install a switch with its air intake vent facing or close to
the air exhaust vent of other devices.
● Do not place any objects on the switch.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Rubber pads (four per switch)
● Security lock (optional, purchased separately)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 91

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

No rubber pads are delivered with a switch that does not support desk mounting.
For some models, rubber pads have been installed before delivery. In this case, you do not
need to install additional rubber pads.

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.
Step 2 Attach the rubber pads to the imprinted round areas at the bottom of the switch.
See a in Figure 3-16.
Step 3 Place the switch gently on the desk. See b in Figure 3-16.
Step 4 (Optional) Install a security lock to lock the switch to the desk. See c in Figure
3-16.

Figure 3-16 Installing a switch on a desk

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 92

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

To determine whether a security lock can be installed, check for the security slot marked
with a padlock icon on the chassis. See Figure 3-17. If there is no security slot on the
switch, it means that the security lock is not supported.
The security slot is 7 mm long and 3 mm wide. The maximum radius of its four round
corners is 1 mm.

Figure 3-17 Security slot marked with padlock icon

----End

3.5.4 Scenario: Wall Mounting

3.5.4.1 Mounting a Switch on the Wall Using Expansion Bolts (With

Mounting Brackets)

Context
This installation method applies to all switch models except the S3700-HI, S5700-
HI, S6720S-EI, and 420 mm deep switches.

DANGER

Before drilling holes on a wall, make sure that no power cables are hidden in the
wall.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 93

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTICE

● For a wall-mounted switch, take water-proofing and dust-proofing measures to

protect the switch from damage caused by water and dust.
● The S5720-16X-PWH-LI-AC, and S6730 (220-mm deep models) need to be
installed with the port side facing up.
● Ensure that there are no flammable or explosive materials nearby the switch.
● Ensure that the switch has at least 100 mm (3.9 in.) free space in all directions.
● When installing a device on a wall using mounting brackets, reserve proper
spacing (59 mm at most) between the device top and the wall.

Tools and Accessories

● Protective gloves
● ESD wrist strap or ESD gloves
● Phillips screwdriver
● Hammer drill (with φ8 drill bit)
● Adjustable wrench
● Marker
● M4 screws (four or six, depending on the switch model. See Figure 3-18.)
● M6 expansion bolts (four per switch, purchased separately)
● Front mounting brackets (two per switch)
NOTE

The M4 screws and front mounting brackets are included in the installation accessory
package.
When installing mounting ears, use screws of the same specifications as those configured
by the manufacturer. Do not use screws that are too long to prevent damage to the device.

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.
Step 2 Use M4 screws to attach a front mounting bracket to each side of the switch. The
type of mounting brackets and the installation method differ depending on switch
model. Figure 3-18 shows the installation methods of different mounting
brackets.
NOTE

If the mounting ear is labeled R/L, install the mounting ear labeled R on the right side of
the device, and install the mounting ear labeled L on the left side of the device. In addition,
the mounting ear marked with R has a ground hole for connecting a ground cable to
provide the grounding function.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 94

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-18 Installing mounting brackets

Step 3 Place the switch against the wall and mark the drilling positions through the holes
of the mounting brackets. See Figure 3-19.

Figure 3-19 Marking the drilling positions

Step 4 Install M6 expansion bolts in the wall.

1. Use a hammer drill (with φ8 drill bit) to drill holes in the marked positions.

2. Insert M6 expansion bolts into the holes and tighten the nuts to secure the
bolts in place.

3. Loosen and remove the nuts from M6 expansion bolts.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 95

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 5 Mount the switch on the wall.

1. Align the holes on the mounting brackets with the M6 expansion bolts and
push the brackets onto the M6 expansion bolts.
2. Fasten the nuts on the M6 expansion bolts.

Figure 3-20 Wall mounting a switch

----End

3.5.4.2 Mounting a Switch on the Wall Using Expansion Bolts (Without

Mounting Brackets)

Context
This installation method applies to the S1700-8-AC, S1700-8G-AC, S1730S-L8T-A,
and S1730S-L8T-MA.

DANGER

Before drilling holes on a wall, make sure that no power cables are hidden in the
wall.

NOTICE

● For a wall-mounted switch, take water-proofing and dust-proofing measures to

protect the switch from damage caused by water and dust.
● Ensure that there are no flammable or explosive materials nearby the switch.
● Ensure that the switch has at least 100 mm (3.9 in.) free space in all directions.

Tools and Accessories

● Hammer drill (with φ6 drill bit)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 96

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

● Expansion Bolts (two)

● Screws (two)
NOTE

The Screws and expansion bolts need to be purchased separately.

Procedure
Step 1 Measure the distance between the two mounting holes on the rear panel of the
switch.

Step 2 Mark the holes accordingly on the wall. See Figure 3-21.

Figure 3-21 Marking the drilling positions

Step 3 Use a hammer drill (with φ6 drill bit) to drill holes, and fix expansion bolts on the
wall.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 97

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-22 Drilling holes in marked positions

Step 4 Mount the switch on the wall.

1. Insert the M4 screws into the expansion bolts on the wall.
2. Mount the device onto the M4 screws.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 98

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-23 Wall mounting a switch

----End

3.5.5 Scenario: Top Wall Mounting

Context
Only the S5720-16X-PWH-LI-AC can be installed on the top wall.

DANGER

Before drilling holes on a wall, make sure that no power cables are hidden in the
wall.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver
● Hammer drill (with φ8 drill bit)
● Adjustable wrench
● M6 expansion bolts (four for each switch)
● M4 screws (six for each switch)
● Top-mounting brackets (two for each switch)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 99

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

The M4 screws are included in the installation accessory package, whereas the M6
expansion bolts and top-mounting brackets need to be purchased separately.
When installing mounting ears, use screws of the same specifications as those configured
by the manufacturer. Do not use screws that are too long to prevent damage to the device.

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.
Step 2 Use M4 screws to attach a top-mounting bracket to each side of the switch.

Figure 3-24 Installing top-mounting brackets

Step 3 Use a marker to mark the positions of mounting holes according to the size of the
switch and positions of the top-mounting brackets. See Figure 3-25.

Figure 3-25 Marking mounting holes

Step 4 Install M6 expansion bolts on the top wall.

1. Use a hammer drill (with φ8 drill bit) to drill holes in the marked positions.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 100

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

2. Insert M6 expansion bolts into the holes and tighten the nuts to secure the
bolts in place.

3. Loosen and remove the nuts from M6 expansion bolts.

Step 5 Mount the switch on the top wall.

1. Align the holes on the top-mounting brackets with the M6 expansion bolts
and push the brackets onto the M6 expansion bolts.
2. Fasten the nuts on the M6 expansion bolts.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 101

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-26 Mounting the switch on the top wall

----End

3.5.6 Scenario: Network Box Mounting

Context
This installation method applies to the S1730S-L4P1T-BUA, S1730S-L8LP2T-BUA,
and S1730S-L8P2T-BUA.

NOTICE

● Do not install the switch outdoors. This switch can only be installed indoors.
● Use standard power adapter delivered with the switch to supply power.
Otherwise, the switch may not work properly or security risks may be
introduced.
● Do not route Ethernet cables or power adapter cables outside a network box.
● The switch installed in a network box must be operated and maintained by
professionals.
● Do not use an enclosed network box and ensure that the air intake and
exhaust vents are not blocked to ensure proper heat dissipation of the switch.
● If the network box is installed indoors or in a corridor that is free from rain, the
network box must meet the requirements of IP31 rating protection. (The first
number "3" indicates that the network box can prevent a solid object with the
diameter greater than or equal to 2.5 mm from entering the network box. The
second number "1" indicates that vertically falling drops shall have no harmful
effects.)
● The vertical distance between the door of the network box and the device must
be greater than 60 mm.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 102

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

The switch provides four screw mounting holes. When the switch is installed in a
network box, the distance between the mounting holes in the network box must
meet the requirements shown in Figure 3-27.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 103

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-27 Spacing of mounting holes on the switch

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 104

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Installing a remote unit in a network box

1. Align the mounting holes on both sides of the switch with the holes on the
mounting kits of the network box.
2. Use a Phillips screwdriver and M4 screws (four delivered with the device) to
secure the switch to the mounting kits of the network box.

Figure 3-28 Installing a switch in a network box

3.5.7 Scenario: DIN Rail Mounting

Context
This installation method applies to the S5735I-S8T4SN-V2, S5735I-S8T4XN-V2,
S5735I-S8T4XN-T-V2, and S5735I-S8U4XN-V2.
Make sure the following prerequisites are met before the installation:
● The DIN rail has been secured in position.
● The switch is placed near the DIN rail for convenient movement.

NOTICE

When multiple S5735I-S8T4SN-V2 switches are installed on the same DIN rail,
there must be a clearance of at least 88 mm between two neighboring switches.
The clearance above a switch must be at least two times the switch's height and
that below must be greater than or equal to the switch's height.
When multiple S5735I-S8T4XN-V2, S5735I-S8T4XN-T-V2, and S5735I-S8U4XN-V2
switches are installed on the same DIN rail, there must be a clearance of at least
66 mm between two neighboring switches. The clearance above a switch must be
at least two times the switch's height and that below must be greater than or
equal to the switch's height.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 105

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Tools and Accessories

● DIN rail (DIN35-7.5 or DIN35-15, prepared by the customer)

Procedure
Step 1 Place the switch's rear panel in front of the DIN rail and ensure that the DIN rail
fits in between the fixture near the top of the switch and spring latch near the
bottom.

Step 2 Make the switch incline forward with the bottom away from the DIN rail, and
place the fixture on the top of the DIN rail.

Step 3 Slowly push the switch toward the DIN rail to make the spring latch at the rear of
the switch move down. The spring latch then bounces back to fix the switch on
the DIN rail.

NOTE

● If the spring latch is too tight to move down, you can pull down the spring latch during the
installation.
● You can also take fixing measures in the horizontal direction of the switch.

----End

3.5.8 Connecting the Ground Cable

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 106

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Context
Grounding the switch helps protect it from lightning, electromagnetic interference,
and electrostatic discharge, and is the prerequisite for a PoE switch to provide
power for a PD.

The ground cable can be connected to a ground bar or a ground point on the
cabinet or rack. The following procedure uses the connection to a ground point as
an example.

WARNING

The switch must be grounded before it is powered on. This protects operators from
electric shock and avoids equipment damage caused by lightning, electromagnetic
interference, or electrostatic discharge.

NOTE

If a cabinet or rack has a protective coating, remove this coating from around the ground
point to ensure a reliable connection.
Some switches have ground points both on the rear, left, or right side of the chassis. You
can use ground points based on the installation scenario.
If a 220 mm deep switch is installed in a 300 mm deep cabinet, remove the ground screw
from the rear of the switch and install it to the ground point on the side of the switch.
For switch models with the ground point at the left or right side of the chassis, connect the
ground cable before mounting the switch in the cabinet or rack.
Some switch models have two ground screws. You need to connect a ground cable to one
of the ground screws.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver
● Ground cable (one per switch)
● M4 screw (already installed on the switch ground point)
● M6 screw (one, purchased separately)
NOTE

The ground cable is included in the installation accessory package.

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.

Step 2 Use a Phillips screwdriver to remove the M4 screw from the ground point on the
switch, as shown in Figure 3-29. Keep the M4 screw for later use.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 107

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-29 Removing the M4 screw from the ground point

Step 3 Attach the M4 lug of the ground cable to the ground point on the switch with the
M4 screw you removed in step 2. Tighten the M4 screw with a torque of 1.4 N m.
See Figure 3-30.
NOTE

The ground cable has an M4 lug at one end and an M6 lug at the other end. The M4 lug is
the smaller of the two.

Figure 3-30 Connecting the ground cable to the switch

Step 4 Attach the M6 lug of the ground cable to a ground point on the cabinet or rack
with an M6 screw. Tighten the M6 screw with a torque of 4.8 N m. See Figure
3-31.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 108

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-31 Connecting the ground cable to a ground point on the cabinet

----End

Follow-up Procedure
After the ground cable is connected, verify that the electrical resistance between
the ground terminal and ground point is less than 0.1 ohm on a multimeter.

3.6 Installing Modules

3.6.1 Installing a Pluggable Power Module

Context
If a switch is delivered with the power modules and fan modules installed in the
chassis, you do not need to install the power modules and fan modules again.
The methods for installing a fan module and a power module are the same. Fan
modules and power modules are both classified into two types: one type is
secured by a captive screw and the other is secured by a lock. Power modules are
used as an example here to describe the installation procedure. All the power
modules and fan modules are hot swappable (except the 870 W PoE power
module).

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 109

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTICE

● If you feel resistance or find the module inclined during the installation, pull
the module out and push it into the slot again. Do not force the module into
the slot as doing this may damage module or the connectors on the backplane.
● Filler panels must be installed in power slots where no power module is
installed.
● A switch can only use power modules matching its chassis model. Using
unsupported power modules will cause unexpected risks.
● If a fan module needs to be replaced, complete the replacement procedure
within 3 minutes.
● Fan modules of different types or with different airflow directions cannot be
used on the same switch.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.

Step 2 Remove the filler panel from the slot where the power module needs to be
installed. Keep the filler panel for future use.
● To remove a filler panel secured by a captive screw, perform the following
steps:
a. Use a Phillips screwdriver to loosen the captive screw on the filler panel
counterclockwise.
b. Pull the filler panel out by the captive screw.

● To remove a filler panel secured by a lock, perform the following steps:

a. Press and hold the lock on the filler panel rightward with your thumb.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 110

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

b. Pull the filler panel out by the handle.

Step 3 Install a power module.

● To install a power module secured by a captive screw, perform the following
steps:
a. Hold the handle on the power module with one hand and support the
bottom with the other hand. Horizontally push the power module into
the slot until it is completely in the slot.
b. Use the Phillips screwdriver to fasten the captive screw on the power
module clockwise.

● To install a power module secured by a lock, hold the handle of the power
module with one hand and support the bottom with the other hand, and
horizontally push the power module into the slot. When the power module is
completely seated in the slot, the lock is locked automatically.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 111

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

----End

3.6.2 Installing a 260 W or 240 W Independent Power Module

Context
The S5720I-12X-PWH-SI-DC can be powered by an external independent 260 W
AC power module (PAC-260WA-E) or 240 W AC power module (PAC240S56-CN).

The S5735I-S8U4XN-V2 can be powered by an external independent 240 W AC

power module (PAC240S56-CN).

● The PAC-260WA-E power module uses 220 V AC input and provides one 56 V
DC output. When the S5720I-12X-PWH-SI-DC is installed in a scenario where
only 220 V AC power is provided, the PAC-260WA-E can be used to transfer
power. The methods for installing the PAC-260WA-E and the S5720I-12X-
PWH-SI-DC are the same. They are installed in the same cabinet using
mounting brackets, and can be installed in the same 1 U space (one in front
of the other).
● The PAC240S56-CN power module uses 220 V AC or 240 V DC input and
provides four 56 V DC outputs. When the switch is installed in a scenario
where 220 V AC or 240 V DC power is provided, the PAC240S56-CN can be
used to transfer power. A DIN rail is required for installing a PAC240S56-CN in
a cabinet. This section describes how to install the PAC240S56-CN.

Ensure that the following prerequisites are met before the installation:

● The DIN rail has been secured on the switch.

● Place the PAC240S56-CN near the DIN rail for convenient movement.

Tools and Accessories

● ESD wrist strap

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 112

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

● DIN rail (DIN35-7.5 or DIN35-15, prepared by the customer)

● PAC240S56-CN 240 W AC power module

Procedure
Step 1 Place the real panel of the power module in front of the DIN rail, and ensure that
the DIN rail fits in between the fixture near the top of the DIN mounting kit and
spring latch near the bottom.
Step 2 Make the power module incline forward with the bottom away from the DIN rail,
and place the fixture at the rear of the DIN mounting kit on the top of the DIN
rail.
Step 3 Slowly push the power module toward the DIN rail to make the spring latch near
the bottom of the DIN mounting kit move down. The spring latch then bounces
back to fix the switch on the DIN rail.

NOTE

If the spring latch is too tight to move down, you can pull down the spring latch during the
installation.

----End

3.6.3 Installing a 60 W Independent Power Module

Context

DANGER

To avoid electric shock, do not connect power cables while the power is on.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 113

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Make sure the following prerequisites are met before the installation:

● The DIN rail has been secured in position.

● The 60 W AC power module is placed near the DIN rail for convenient
movement.

Tools and Accessories

● ESD wrist strap
● Phillips screwdriver
● M3 screws
● DIN rail
● 60 W AC power module

Procedure
Step 1 Wear an ESD wrist strap. Ensure that the ESD wrist strap is grounded and in a
close contact with your wrist.

Step 2 Mount the DIN mounting kit onto the rear panel of the 60 W AC power module
with M3 screws, and then use a Phillips screwdriver to tighten the M3 screws.

Step 3 Place the rear panel of the 60 W AC power module in front of the DIN rail and
ensure that the DIN rail fits in between the fixture near the top of the DIN
mounting kit and spring latch near the bottom.

Step 4 Make the power module incline forward with the bottom away from the DIN rail,
and place the fixture at the rear of the DIN mounting kit on the top of the DIN
rail.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 114

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 5 Slowly push the power module toward the DIN rail to make the spring latch near
the bottom of the DIN mounting kit move down. The spring latch then bounces
back to fix the power module on the DIN rail.

NOTE

If the spring latch is too tight to move down, you can pull down the spring latch during the
installation.

----End

3.6.4 Installing a Card

Context
This section describes how to install a pluggable card in the S series fixed switches,
using a 4-port front card as an example. The installation method is the same for
all switch models that support pluggable cards. For details about which models
support what cards, see "Cards" in the Hardware Description.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 115

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTICE

● Only switch models S5700-SI, S5710-LI, and S5700-EI do not support hot
swappable cards, the switch must be powered off before a card can be
installed.
● To use a front 4xGE or 4x10GE optical interface card on the S5700-SI, S5710-LI,
and S5700-EI, you must also install an extended rear card.
● If you feel resistance or find the card inclined during the installation, pull the
card out and push it into the slot again. Do not force the card into the slot as
doing this may damage the connectors on the card and the backplane.
● Install filler panels in vacant slots.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.
Step 2 Remove the filler panel from the slot into which the card will be installed. Keep
the filler panel for future use.
1. Use a Phillips screwdriver to loosen the captive screw on the filler panel.
2. Holding the captive screw, pull out the filler panel.

Step 3 Install the card in the switch.

1. Pull the ejector lever of the card 45 degrees outward. Gently push the card
into the chassis with your thumbs placed below the captive screws, until the
screw on the front panel is completely in the chassis.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 116

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

Front cards for the S3700-HI, S5700-HI, and S5710-HI have no screws. However, the
installation method is similar.
2. Push the ejector lever inward to lock the card.

3. Use a Phillips screwdriver to tighten the captive screws.

----End

3.6.5 Installing an Optical Module

Context
This section describes how to install an optical module. The method used to install
a copper transceiver module is the same, except that the copper transceiver
module connects to a network cable instead of optical fibers.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 117

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

DANGER

Never look directly into an optical module or the ends of optical fibers. Optical
modules and connected fibers emit laser radiation that can cause eye damage.

NOTICE

● Do not touch the edge connector of an optical module during the installation.
● Install an optical module on a port before connecting optical fibers to the
transceiver module.
● Install dust plugs on idle optical ports.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Dust plugs

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.
Step 2 Remove the dust plug from an optical port. Keep the dust plug for future use.
Step 3 Ensure that the optical module is correctly oriented and gently push it into the
optical port until you hear a click.

NOTICE
If the optical module cannot be completely inserted into the optical port, do not
force it into the port. Turn the optical module 180 degrees and try again.

Figure 3-32 Installing an optical module

Step 4 Check whether the transceiver module is securely seated. While keeping the
handle of the transceiver module closed, grasp the two sides of the transceiver
module with your thumb and forefinger and gently pull it.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 118

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

● If the transceiver module does not pull out, it is installed correctly.

● If the transceiver module pulls out, reinstall it.
NOTE
Ensure that transceiver modules are fitted with dust plugs when not in use and remove the
dust plugs only when you are ready to connect optical fibers.

----End

3.7 Installing an HDF

Context
This section describes how to install the HCDF48PDLC00 hybrid cable distribution
frame (HDF) in a 19-inch standard cabinet.
Before installation, ensure that:
● The cabinet has been secured and meets the requirements specified in 3.3.3
Checking the Cabinet or Rack.
● The installation position of the HDF has been planned.
● The HDF to be installed has been placed near the cabinet for convenient
movement.
● Before the installation, ESD measures have been taken. For example, you are
already wearing ESD gloves or an ESD wrist strap.
● The left and right sides of the HDF have been aligned horizontally before it is
secured to the cabinet. If not, do not forcibly install the HDF; otherwise, it will
be distorted.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver
● Flat-head screwdriver
● Floating nuts (four for each HDF)
● M6 screws (four for each HDF)

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. If you wear an ESD wrist strap, ensure that
one end of the ESD wrist strap is grounded and the other end is in close contact
with your wrist.
Step 2 Install floating nuts on the mounting rails of the cabinet.
Determine the installation positions of floating nuts on the mounting rails
according to the planned installation position of the HDF. Use a flat-head
screwdriver to install four floating nuts on the front mounting rails, two on each
side. Align the mounting holes on the mounting brackets with two holes with one
hole between them on the mounting rails. Ensure that the floating nuts on both
sides are aligned horizontally.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 119

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

Pay attention to the scale markings on the mounting rails because three adjacent mounting
holes may not be 1 U.

Step 3 Install the HDF into the cabinet.

1. Hold the bottom of the HDF and align the holes on the mounting brackets on
both sides of the HDF with the floating nuts on the front mounting rails.
2. Hold the HDF with one hand, and use a Phillips screwdriver to tighten the M6
screws on the HDF with the other hand to secure the HDF to the mounting
rails of the cabinet.

Figure 3-33 Installing an HDF into a cabinet

Step 4 Connect hybrid cables to the HDF. For details, see 3.8.8 Connecting Second-
Generation Hybrid Cable.

----End

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 120

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

3.8 Connecting a Switch

3.8.1 Connecting Power Cables

Context

DANGER

There is a risk of electrical shock when connecting power cables. To avoid electric
shock, do not connect power cable while the power is on.

NOTICE

● Power cables of the switch must be routed indoors or buried underground if

they are led in from the outside. Do not aerially route the power cables
outdoors.
● Do not power on the switch until you finish installing the switch and
connecting all cables.
● Power cables delivered with the switch are for use with this switch only.
● When routing power cables for the S5735-L8T4X-IA1, S5735-L8P4X-IA1, and
S5735-L24T4X-IA1, do not bind multiple power cables together.

The S series switches have a built-in power supply unit or support pluggable or
independent power modules. The required power cables and their connection
methods vary according to the power modules used on the switches.
For non-S5720I-SI series switches:
● To connect to an AC power outlet, the switch must have a built-in AC power
supply unit or use a pluggable AC power module, which must be connected
using an AC power cable or AC power adapters complying with local
standards.
● To connect to an AC power distribution unit (PDU), the switch must have a
built-in AC power supply unit or use a pluggable AC power module, which
must be connected using a C13 straight female to C14 straight male AC
power cable.
● To connect to a DC power distribution box, the switch must have a built-in DC
power supply unit or use a pluggable DC power module, which must be
connected using DC power cables.
● If the external power supply system provides high-voltage DC power, the
switch must use AC power cables for the built-in or pluggable AC power
modules that support high-voltage DC power input. For such an AC power
cable, the PE wire must be grounded, and the L or N wire must be connected
to the positive or negative terminal of the high-voltage DC input.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 121

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

The AC power cable parameters vary in different countries or regions. The figures in this
section are only for reference.
For a desk-mounted DC switch, use 18 AWG (1 mm2) DC power cables with a maximum
insulation diameter of no more than 2.1 mm (0.08 in.). UL1007 DC power cables are
recommended.
The S5735-L8P4S-QA1 uses the power adapter delivered with the device. The connection
method is similar to that of the AC power cable. After the cable is connected, bind the
cable with the power adapter cable locking strap delivered with the device.
For the S5720I-SI series switches and the PAC-260WA-E or PAC240S56-CN, Phoenix
connectors and power cables are required.
For the S5735I-S-V2 series switches and the PAC60S12-AN or PAC240S56-CN, Phoenix
connectors and power cables are required.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver
● (Optional) AC terminal locking latch
● (Optional) Wire stripper

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.
Step 2 Turn off the external power supply system for the switch.
Step 3 Turn off the power switch on the switch or power module.
NOTE

Skip this step if there is no power switch on the switch or power module.

Step 4 Connect a power cable to the switch or power module.

● To connect an AC power cable to a built-in AC power supply unit or AC power
module (except for the S5720I-SI), perform the following steps (built-in AC
power supply used as an example):
a. (Optional) Install the AC power cable locking strap.
The AC power cable locking strap is not delivered with the switch.

b. Insert the AC power cable plug into the power socket on the switch or AC
power module.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 122

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

c. (Optional) If an AC power cable locking strap is installed, adjust its size

to fit the AC power cable plug.

NOTE

Some models use metal locking latches. Figure 3-34 shows a metal locking latch.

Figure 3-34 Using a metal locking latch

● To connect DC power cables to a built-in DC power supply unit or a 150 W or

170 W DC power module (except for the S5720I-SI), perform the following
steps (150 W DC power module used as an example):
a. Use a Phillips screwdriver to loosen the screw on the DC terminal
protective cover, and then remove the protective cover.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 123

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

b. Use the Phillips screwdriver to remove the screws on the two DC

terminals.

c. Secure the DC power cables to the DC power module with the screws you
removed in step b.
Ensure the correct polarity of connected cables. If you use DC power
cables delivered from Huawei, connect the -48 V return ground cable
(black) to the RTN(+) terminal, and connect -48 V power cable (blue) to
the NEG(-) terminal.

d. Install the protective cover and fasten the screw.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 124

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

● To connect DC power cables to a 180 W, 260 W, 350 W, 650 W, 1000 W DC ,

or 1200 W DC power module, insert the DC power cable plug into the power
sockets on the DC power module. Ensure that the positive and negative poles
of the plug are connected to the positive and negative sockets, respectively.

● For the AC input of the S5720I-SI or the PAC-260WA-E, PAC60S12-AN or

PAC240S56-CN power module, connect the power cables as follows:
– If the AC power cables are semi-finished cables:
i. Cut the power cables to a proper length based on the installation
position of the switch in the cabinet.

ii. Use a wire stripper to peel 7-10 mm length of insulation off one end
of the power cables.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 125

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

iii. Press and hold the spring in the middle of the Phoenix connector,
insert the live wire (L), neutral wire (N), and ground wire (PE) into
the terminals according to the sequence shown in the following
figure, and release the spring to lock the cables.

iv. Insert the Phoenix connector into the AC input port on the switch or
power module, and tighten the screws on both sides of the Phoenix
connector.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 126

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

v. If a three-pin AC power plug purchased by the customer is used,

connect the power cable to the three-pin AC power plug as follows:
1) Use a tool (such as a screwdriver, depending on the plug type)
to open the three-wire AC power plug.
2) Use a wire stripper to remove the required length of insulation
(depending on the plug type) off one end of the power cable.
3) Secure the live wire (L), neutral wire (N), and ground wire (PE)
to the corresponding L, N, and PE terminals in the power plug.
4) Use the tool to reassemble the power plug.

DANGER

○ Ensure the live wire (L), neutral wire (N), and ground wire (PE)
are securely installed in the correct terminals. Pull each wire to
check whether they are securely installed.
○ Ensure that no metal wire is exposed outside the power plug.

– If the AC power cables are finished cables:

i. Cut off the C13 straight female of the finished AC power cable.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 127

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

ii. Use a wire stripper to peel 40 mm length of the outer sheath and
then peel 7-10 mm length of inner insulation.

iii. Use a multimeter to distinguish the live wire (L), neutral wire (N),
and ground wire (PE). Generally, L is red, N is blue, and PE is yellow-
green.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 128

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

iv. Press and hold the spring in the middle of the Phoenix connector,
insert the live wire (L), neutral wire (N), and ground wire (PE) into
the terminals according to the sequence shown in the following
figure, and release the spring to lock the cables.

v. Insert the Phoenix connector into the AC input port on the switch or
power module, and tighten the screws on both sides of the Phoenix
connector.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 129

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

DANGER

There is a risk of electric shock when handling the Phoenix connector. To

avoid electric shock, ensure that the L/N/PE wires are connected in sequence.
After power cables are connected to the Phoenix connector, ensure that
copper conductors are not bent and there are no exposed metal parts.
Ensure that power cables are securely connected to the Phoenix connector
(you can pull the cables one by one for check).

Figure 3-35 Connections of AC input power cables for the PAC-260WA-E

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 130

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-36 Connections of AC input power cables for the PAC240S56-CN or

PAC60S12-AN

● For the DC input of the S5720I-SI or DC output of the PAC-260WA-E power

module, connect the power cables as follows:
a. Use a wire stripper to peel about 7 mm length of insulation coating off
one end of the positive and negative cables. Press and hold the spring in
the middle of the Phoenix connector, insert the bare wires of the power
cable into the socket according to the sequence shown in the figure, and
release the spring to lock the cable.
b. Insert the Phoenix connector into the DC input port on the switch or the
DC output port on the power module, and tighten the screws on both
sides of the Phoenix connector.

Figure 3-37 Connections of DC output power cables for the PAC-260WA-E

● For the DC output of the PAC240S56-CN or PAC60S12-AN power module,

connect the power cables as follows:
a. Use a wire stripper to peel about 7 mm length of insulation coating off
one end of the positive and negative cables. Insert the bare wires of the
power cable into the Phoenix connector according to the sequence shown
in the figure, and tighten the screws to lock the cable.
b. Insert the Phoenix connector into the DC output port on the power
module, and tighten the screws on both sides of the Phoenix connector.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 131

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-38 Connections of DC output power cables for the PAC240S56-CN

Step 5 Connect the power cables to the external power supply system.
● If you are using the standard AC power cables for your geographical location,
connect them to an AC power strip or power distribution box.
● If you are using C13 straight female to C14 straight male AC power cables,
connect them to a PDU.
● If you are using DC power cables, connect them to a DC power distribution
box. Ensure correct connections of the positive and negative power cables.
For the AC input of the S5720I-SI or the PAC-260WA-E, the 220 V mains power is
used.
For the PAC240S56-CN or PAC60S12-AN, the 220 V AC or 240 V DC power is used.

----End

Follow-up Procedure
Complete a post-installation check before powering on the switch. For the post-
installation checklist, see 3.9 Post-installation Checks. For details about how to
power on the switch, see 3.11 Powering on a Switch for the First Time.

3.8.2 Connecting Ethernet Cables

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 132

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Context

NOTICE

● Before deploying Ethernet cables, test their continuity.

● If Ethernet cables of the switch need to be routed outdoors, bury them
underground or put them through steel pipes to avoid lightning strikes to the
switch. Do not aerially route Ethernet cables outdoors.
● Keep signal cables more than 10 cm away from power cables.
● When a switch with 48 optical ports and copper modules is installed in a 600
mm deep cabinet, only Category 5 unshielded twisted pairs can be used.
● When a switch with 48 electrical ports fully used is installed in a 600 mm deep
cabinet, only Category 5 unshielded twisted pairs can be used.
● Ensure Ethernet cables have a stable environment. There should be no external
power cables in contact with Ethernet cables or devices at either end of the
Ethernet cables, as external power cables may damage the devices or Ethernet
cables through leakage current.
● When connecting Ethernet cables to a copper module, organize the cables and
wrap them up at the position parallel with the cabinet to prevent the cables
from hanging down naturally and to prevent the copper module from being
affected when the cables are routed.
● For 10GBASE-T electrical ports, use Category 6A STP or higher category twisted
pairs. Category 6A STP and Category 7 twisted pairs can prevent alien crosstalk.
These cables can be used together with other types of cables and must be
bundled on supporting objects because they are heavy.
● Strong interference may cause a bit error rate of no more than 10-7 on multi-
GE ports (10GBASE-T and IEEE802.3bz). To prevent this problem, keep the
switch away from interference sources or take adequate interference shielding
measures. Triggering the fast retrain function will cause a large number of bit
errors in a period of around 30 ms.
● If the management port is located at the rear of the device, reserve space for
cabling when connecting the network cable to the management port to
prevent the insertion and removal of cards, fans, and power modules.

If a switch does not support or is not installed with a rear card, the Ethernet
cables used on its electrical ports and the distance between the switch front panel
and cabinet front door must meet the requirements described in Table 3-17.

Table 3-17 Requirements for Ethernet cables

Network Distance (Excluding the Length of a Copper Module) Between

Cable the Switch Front Panel and Cabinet Front Door (X)
Type

Category 5
unshielded
twisted
pair X ≥ 80 mm (3.1 in.)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 133

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Network Distance (Excluding the Length of a Copper Module) Between

Cable the Switch Front Panel and Cabinet Front Door (X)
Type

Category 5
shielded
twisted
pair X ≥ 110 mm (4.3 in.)

Category 6 X ≥ 120 mm (4.7 in.)

twisted
pair

When a switch is installed with a rear card:

● In a cabinet deeper than 600 mm, the Ethernet cables used on its electrical
ports and the distance between the switch front panel and cabinet front door
must meet the requirements described in Table 3-17. There is no specific
requirement for the distance between the switch rear panel and cabinet rear
door.
● In a 600 mm deep cabinet, the Ethernet cables used on its electrical ports, the
optical fibers used on the rear card, and the distances between the switch
panels and cabinet doors must meet the requirements described in Table
3-18.

Table 3-18 Requirements for Ethernet cables and optical fibers

Network Distance Distance Between the Switch Rear Panel

Cable (Excluding the and Cabinet Rear Door (Y)
Type Length of a
Copper Ultra-short Short Pigtail Regular
Module) Pigtail Fiber or
Between the QSFP+ Fiber
Switch Front
Panel and
Cabinet Front
Door (X)

Category
5
unshielde 80 mm (3.1
d twisted in.) < X < 100 Y ≥ 60 mm Y ≥ 72 mm Y ≥ 80 mm
pair mm (3.9 in.) (2.4 in.) (2.8 in.) (3.1 in.)

Cannot be
Y ≥ 60 mm Y ≥ 72 mm used
(2.4 in.) (2.8 in.) together with
Route Route Category 5
Category Ethernet Ethernet shielded
5 shielded cables from cables from twisted pair
twisted X = 110 mm both sides of both sides of Ethernet
pair (4.3 in.) the cabinet. the cabinet. cables.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 134

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Network Distance Distance Between the Switch Rear Panel

Cable (Excluding the and Cabinet Rear Door (Y)
Type Length of a
Copper Ultra-short Short Pigtail Regular
Module) Pigtail Fiber or
Between the QSFP+ Fiber
Switch Front
Panel and
Cabinet Front
Door (X)

Category X = 120 mm Y ≥ 60 mm Cannot be Cannot be

6 twisted (4.7 in.) (2.4 in.) used used
pair Route together with together with
Ethernet Category 6 Category 6
cables from twisted pair twisted pair
both sides of Ethernet Ethernet
the cabinet. cables. cables.

NOTE

● For a switch with 48 electrical ports, route Ethernet cables from both sides of the
cabinet. Specifically, route cables to the first 24 ports from the left of the cabinet, and to
the last 24 ports from the right of the cabinet.
● If the cabinet is densely cabled from both sides, it is recommended to reserve 1 U of
clearance below the switch for a cable tray. Route the Ethernet cables through the cable
tray and bundle the cables on both sides of the cabinet, to ensure that the weight of the
cables is supported by the cabinet.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Cable tie gun
● Cable ties
● Marker
● Network cable labels

Procedure
Step 1 Determine the number and type of ports to be connected and plan the cabling
routes.

Step 2 Obtain the desired quantity and lengths of Ethernet cables.

Step 3 Attach temporary labels to both ends of each Ethernet cable and number them
corresponding to port numbers. For details, see 4.4.2 Engineering Labels for
Network Cables.

Step 4 Route the Ethernet cables, arrange the cables in the cabinet, and then install cable
connectors. Cable connectors made onsite must be securely attached and comply
with related standards.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 135

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 5 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.
Step 6 Connect the cable connectors to the ports, matching the numbers on the Ethernet
cables to those on the ports. After connecting the cables, verify that they are all
correctly connected.

Step 7 Arrange the Ethernet cables so that they are parallel, and then bundle them with
cable ties loosely according to Table 3-19. Use a cable tie gun to cut off
redundant cable ties. The use of protective pads under the cable ties is
recommended, as shown in Figure 3-39.
NOTE

A bundle cannot have more than 24 cables. A bundle of no more than 12 cables is
recommended.

Table 3-19 Spacing between cable ties

Diameter of a Bundle Spacing Between Cable Ties

< 10 mm (0.39 in.) 150 mm (5.91 in.)

10-30 mm (0.39-1.18 ft.) 200 mm (7.87 in.)

> 30 mm (1.18 ft.) 300 mm (11.81 in.)

Figure 3-39 Bundling Ethernet cables

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 136

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 8 Replace all the temporary labels on the Ethernet cables with permanent labels.

----End

3.8.3 Connecting Optical Fibers

Context

DANGER

Never look directly into an optical module or the ends of optical fibers. Optical
modules and connected fibers emit laser radiation that can cause eye damage.

NOTICE

Before deploying optical fibers, test connectivity of the optical fibers.

NOTICE

● Keep optical fibers more than 10 cm (3.9 in.) away from power cables.
● Use corrugated pipes to protect optical fibers routed in a cabinet. The bend
radius of an optical fiber must be at least 20 times larger than its diameter.
Generally, the bend radius of optical fibers should be no less than 40 mm (1.57
in.).

NOTICE

Fiber connectors must be tidy and clean to ensure normal communication. If a

fiber connector is contaminated, clean it with fiber cleaning fabric.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Corrugated pipe
● Fiber binding tape
● Marker
● Engineering labels for optical fibers
● (Optional) Tweezers

Procedure
Step 1 Determine the number and type of ports to be connected and plan the cabling
routes.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 137

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 2 Obtain the desired types, quantity, and lengths of optical fibers.

Step 3 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.

Step 4 Attach temporary labels to both ends of each optical fiber and number them
corresponding to port numbers.

Step 5 Remove the dust plugs from optical modules and the dust caps from the optical
fibers to be connected.

Step 6 Connect optical fibers to the optical modules on the device, matching the numbers
on the optical fibers to those on the ports. To connect them, align the fiber
connector with the bores on the optical module and insert the fiber connector.
When you hear a click, the fiber connector is securely connected. See Figure 3-40.
After connecting the optical fibers, verify that they are all correctly connected.
NOTE

Connect the receive and transmit ends of a fiber connector to the receive and transmit
bores of the optical module.

Figure 3-40 Connecting optical fibers to an optical module

To remove optical fibers from an optical module, gently push the fiber connector
inward, and then pull the fiber connector out while pressing the locking clips. Do
not forcibly pull the fiber connector. See Figure 3-41.
NOTE

If optical ports are densely populated, use the tweezers to remove optical fibers.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 138

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-41 Removing optical fibers

Step 7 Arrange the optical fibers to make them parallel and bundle them with fiber
binding tape at a spacing of 150-300 mm (5.9-11.8 in.).

Step 8 Replace all the temporary labels on the optical fibers with permanent labels.

----End

3.8.4 Connecting Copper Cables

Context

NOTICE

● Both ends of an idle copper cable must be covered by an ESD cap.

● Do not bend copper cables over their minimum bend radius. Doing so may
damage wires in the cables.
● Connectors of copper cables must be clean to ensure normal communication. If
a connector is contaminated, clean it with cleaning fabric.
● Ensure that the bend radius of the copper cables or optical fibers is greater
than the minimum bend radius required. For specific bend radiuses of various
cables, see "Cables" in the Hardware Description of the product.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Cable tie gun
● Cable ties
● Marker
● Copper cable labels

Procedure
Step 1 Determine the number and type of ports to be connected and plan the cabling
routes.

Step 2 Obtain the desired quantity and lengths of copper cables.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 139

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 3 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.
Step 4 Attach temporary labels to both ends of each copper cable and number them
corresponding to port numbers. For details, see 4.4.3 Engineering Labels for User
Cables.
Step 5 Connect the copper cables to ports on the switch, matching the numbers on the
copper cables to those on the ports. To connect them, align the copper cable
connector with the port and insert the connector. When you hear a click, the
copper cable is securely connected. See Figure 3-42.
After connecting copper cables, verify that they are all correctly connected.

Figure 3-42 Connecting a copper cable

To remove a copper cable, gently push the cable connector inward and then pull
the handle of the connector. Do not forcibly pull the cable connector. See Figure
3-43.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 140

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-43 Removing a copper cable

Step 6 Arrange the copper cables to make them parallel, and bundle them with cable ties
at a spacing of 150-300 mm (5.9-11.8 in.). Use a cable tie gun to cut off
redundant cable ties.
Step 7 Replace all the temporary labels on the copper cables with permanent labels.

----End

3.8.5 Assembling the First-Generation Hybrid Cables

Context
The first-generation hybrid cable is composed of optical fibers and copper cores. It
is mainly used to connect a hybrid optical-electrical switch to an AP or a remote
unit for PoE power supply and data transmission.
The first-generation hybrid cables must be made onsite using the purchased bare
wires, auxiliary material packages that contain RJ45 connectors, and auxiliary
material packages used for mechanical or fusion splicing of optical fibers.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 141

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTICE

● The first-generation hybrid cables can only be used indoors and cannot be
connected to outdoor APs.
● The first-generation hybrid cables cannot be connected through a cable
distribution frame. Copper cores in a hybrid cable must be directly connected to
a switch and an AP.
● Assembling cables onsite must be performed with no power supply connected.
● Do not stretch, step on, or place heavy objects on hybrid cables. Keep the
cables away from sharp objects.
● At least three trained and qualified persons are required for laying out hybrid
cables. Cabling is allowed only when communication facilities are available.
● Route cables according to the planned positions and mark the cables in
advance to eliminate the need to differentiate cables on the switch side after
the cables are routed. Reserve a sufficient length of cable at the end where the
cable label is attached, avoiding cutting off the cable label during cable
assembling.
● A maximum of 100 hybrid cables can be bundled when no pipe is used. When a
pipe is used, ensure that one-third space inside the pipe is vacant.
● When routing hybrid cables, coil the excess optical fibers around dedicated
devices, such as a fiber management tray. Even force needs to be applied when
cables are coiled to ensure the cables are not overly bent.
● After hybrid cables are assembled onside, you are advised to use a red pointer
and an optical fiber adapter to check whether optical fibers are broken or not.
● Optical fiber connectors not in use must be covered with dustproof caps. Ensure
that the end face of optical fiber connectors is clean. When an optical fiber
connector is installed or removed, you need to protect its end face from
touching other objects, preventing contamination or damage. If any dirt is
found, use alcohol or dust-free paper to clean it. If the end face is damaged,
start from the very beginning to assemble the cable.
● Optical fiber connectors must be assembled by engineers experienced in optical
fiber mechanical connection and equipped with professional optical fiber
assembling and testing tools. When assembling optical fiber connectors, do not
bend optical fibers or contaminate the end faces. Otherwise, services may be
adversely affected.
● The bending radius of a hybrid cable is at least five times its diameter. The
minimum bending radius of a branch optical fiber inside a hybrid cable is 15
mm.
● To facilitate cabling, it is recommended that hybrid cables connected to the first
twelve multi-GE ports and 10GE optical ports (ports 1 to 12) of a hybrid
optical-electrical switch be routed along the left side of the cabinet. In addition
to this, those connected to the last twelve multi-GE ports and 10GE optical
ports (ports 13 to 24) be routed along the right side of the cabinet.
● After hybrid cables are connected to switches and APs, you are advised to bind
the optical fibers together using binding straps. Then bind the copper cores and
optical fibers together using cable ties to prevent the cables from reaching the
cabinet door.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 142

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

● It is recommended that the exposed optical fibers and copper cores on the AP
side be protected by corrugated pipes.

Hybrid cables must be led to target positions by slowly and evenly turning the
cable drum. It is recommended that a 5 m to 15 m length be led every minute. Do
not place the cable drum upside down and manually lead out the cables, as
shown in Figure 3-44.

Figure 3-44 Correct and incorrect routing of hybrid cables

Do not circle or twist hybrid cables or bind them at the bend, as shown in Figure
3-45.

Figure 3-45 Circled or twisted cables

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 143

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

At corners and turns, hybrid cables must be laid out by an appointed person to
ensure they are not blocked or stuck. The minimum bending radius must be
guaranteed, as shown in Figure 3-46.

Figure 3-46 Incorrect routing of a hybrid cable at a 90° corner

Tools and Accessories

Table 3-20 Tools and accessories

Tool Appearance Description

Cable Used to peel off the outer

stripper sheath of hybrid cables.
This item does not come
with the device and needs
to be purchased
separately.

Flat drop Used to remove the jacket

cable of optical fibers in hybrid
stripper cables. This item does not
come with the device and
needs to be purchased
separately.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 144

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Tool Appearance Description

Fiber cleaver Used to cut optical fibers.

This item does not come
with the device and needs
to be purchased
separately.

Duckbilled Used to remove the jacket

wire stripper of copper cores in hybrid
cables. This item does not
come with the device and
needs to be purchased
separately.

Fiber - Used to clean bare fibers.

cleaning This item does not come
paper with the device and needs
to be purchased
separately.

Alcohol - Used to clean bare fibers.

(concentrati This item does not come
on: 99.5%) with the device and needs
to be purchased
separately.

RJ45 Included in the 02233FKX

connector auxiliary material
package, which needs to
be purchased.

LC connector Included in the 02233FKY

and wedge and 02233FLA auxiliary
unit material packages, which
need to be purchased.

Fiber clamp Included in the 02233FKY

and 02233FLA auxiliary
material packages, which
need to be purchased.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 145

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Tool Appearance Description

Fiber holder Included in the 02233FKY

and 02233FLA auxiliary
material packages, which
need to be purchased.

Fiber coating Included in the 02233FKY

stripper and 02233FLA auxiliary
material packages, which
need to be purchased.

Fiber clamp Included in the 02233FKY

release tool and 02233FLA auxiliary
material packages, which
need to be purchased.

Fiber Used to strip a pigtail.

stripper This item is used only in
pliers the fusion splicing
scenario and needs to be
purchased separately.

Single-core Used to fusion splice the

fiber fusion optical fiber and pigtail.
splicer This item is used only in
the fusion splicing
scenario and needs to be
purchased separately.

Heat shrink Used only in the fusion

tubing splicing scenario. It is
included in the 02233FLA
and 02233FLB auxiliary
material packages, which
need to be purchased.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 146

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Tool Appearance Description

Fiber pigtail Used only in the fusion

splicing scenario. It is
included in the 02233FLA
and 02233FLB auxiliary
material packages, which
need to be purchased.

Fusion splice Used only in the fusion

protection splicing scenario. It is
sleeve included in the 02233FLA
and 02233FLB auxiliary
material packages, which
need to be purchased.

Red pointer Used to test the

connectivity of optical
cables. This item does not
come with the device and
needs to be purchased
separately.

Laser source Used to test the insertion

loss of optical fibers. This
item does not come with
the device and needs to
be purchased separately.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 147

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Tool Appearance Description

Optical Used to test the insertion

power meter loss of optical fibers. This
item does not come with
the device and needs to
be purchased separately.

Procedure
Step 1 Peel off at least a 400 mm long section of the outer sheath from one end, for
connecting to a switch of a hybrid cable. Peel off at least 300 mm from the other
end, for connecting to an AP. All figures in this section assume that the left end of
the cable is connected to a switch and the right end is connected to an AP.

Figure 3-47 Peeling off the outer sheath

NOTICE

● You are advised to peel off the outer sheath in two or three sections, allowing
the outer sheath to be easily peeled off and preventing optical fibers from
being broken.
● Do not damage the copper cores or optical fibers.
● Do not overly bend the cable at the stripping positions.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 148

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 2 Cut the cable according to the cabling direction in a cabinet.

NOTE

Cut the copper cores or optical fibers connected to a switch depending on the side of the
cabinet along which hybrid cables connect to the switch:
● Left side: The optical fibers must be 100 mm longer than the copper cores. In this case,
cut the copper cores.
● Right side: The copper cores must be 100 mm longer than the optical fibers. In this case,
cut the optical fibers.
The copper cores and optical fibers connected to an AP do not need to be cut.

Figure 3-48 Cutting 100 mm of the copper cores (switch cabling along the left
side of the cabinet)

Figure 3-49 Cutting 100 mm of the optical fibers (switch cabling along the right
side of the cabinet)

Step 3 Assemble optical fibers by referring to 3.8.5.1 Assembling Optical Fibers in the
First-Generation Hybrid Cable in Mechanical Splicing Mode or 3.8.5.2
Assembling Optical Fibers in the First-Generation Hybrid Cable in Fusion
Splicing Mode.
Step 4 Assemble RJ45 connectors by referring to 3.8.5.3 Assembling Copper Cores in
the First-Generation Hybrid Cables.

Figure 3-50 Hybrid cable with connectors assembled (switch cabling along the left
side of the cabinet)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 149

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-51 Hybrid cable with connectors assembled (switch cabling along the
right side of the cabinet)

Step 5 Use a red pointer and an optical power meter to test the connectivity and
insertion loss of optical fibers in the finished hybrid cable. The insertion loss of
optical fibers must be less than 1.2 dB.

----End

3.8.5.1 Assembling Optical Fibers in the First-Generation Hybrid Cable in

Mechanical Splicing Mode

Context
Optical fibers in the first-generation hybrid cable can be assembled in either of
the two modes: mechanical splicing and fusion splicing.

● In mechanical splicing mode, LC connectors in the purchased 02233FKY or

02233FLA auxiliary material package are used to terminate optical fibers.
● In fusion splicing mode, optical fibers are fusion spliced with fiber pigtails in
the purchased 02233FLA or 02233FLB auxiliary material package, without the
need of LC connectors.

Procedure
Step 1 Assemble an optical fiber.
1. Use a flat drop cable stripper to remove the unwanted fiber jacket. Note that
using fiber stripper pliers may damage the optical fiber and is therefore not
recommended.

CAUTION

The bare fiber must be at least 50 mm long, without any damages.

Replace the flat drop cable stripper if it is not sharp enough to cut off the
steel wire or damages the optical fiber.
Ensure that the cut surfaces are neat and even, the optical fiber is not
damaged, and the steel wire in the jacket is not bent.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 150

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

2. Bend the bare fiber to an angle greater than 60º in the upward and
downward directions, three times in each direction.

CAUTION

If the optical fiber is broken during the bending, start from the very beginning
to assemble the optical fiber.

Step 2 Clamp the optical fiber.

1. Open the fiber clamp and insert the optical fiber.

CAUTION

Vertically place the optical fiber inside the fiber clamp, with the narrow side
facing the notch.
Ensure that there is no gap between the fiber clamp and the cut surfaces.
(See the red dotted line.)

2. Close the fiber clamp and press it tight.

Step 3 Strip the optical fiber.

1. Place the assembly inside the fiber holder and close the buckles.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 151

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

2. Place the fiber holder (with the assembly) inside the fiber coating stripper.

CAUTION

Ensure that there is no gap between the fiber holder and the fiber coating
stripper. (See the red dotted line.)

3. Press the fiber coating stripper and pull out the fiber holder at an even speed
to remove the fiber coating.

CAUTION

Be sure not to tilt the fiber holder when pulling it out. Otherwise, the optical
fiber will break.

Step 4 Cut the optical fiber.

1. Bend the bare fiber to an angle greater than 60º in the upward and
downward directions, three times in each direction.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 152

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

CAUTION

If the optical fiber is broken during the bending, start from the very beginning
to assemble the optical fiber.

2. Clean the bare fiber using fiber cleaning papers with absolute alcohol.

CAUTION

Do not break the optical fiber during the cleaning.

3. Place the fiber holder on the fiber cleaver, ensuring there is no gap between
them.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 153

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

CAUTION

If the cutting is not completed at a time, start from the very beginning to
assemble the optical fiber.
If the cutter blade is worn out, replace it immediately.

4. Cut the optical fiber.

5. Take out the assembly from the fiber holder.

6. Use the fiber holder to check the fiber length. If the lengths of the bare fiber
without coating and the bare fiber with coating exceed the scale on the fiber
holder, start from the very beginning to assemble the optical fiber.

Step 5 Assemble the optical fiber.

1. Press the wedge unit and ensure that the wedge unit is firmly seated on the
LC connector. Press the wedge unit first at part 1 and then at part 2. Then
follow directions indicated by numbers 1 and 2 on the wedge unit.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 154

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

2. Insert the optical fiber until the fiber clamp is entirely within the LC connector
(you will hear a click).

CAUTION

Do not squeeze the wedge unit during the assembly.

3. Inspect the bare wire on the LC connector. The bare fiber should be slightly
bent and should not protrude from the LC connector.

Step 6 Remove the protection cover of the wedge unit, and release the wedge unit by
squeezing it.

CAUTION

Do not overly bend the optical fiber near the LC connector.

Step 7 (Optional) Disassemble the optical fiber.

NOTE

If the optical fiber fails the performance test, disassemble and re-assemble it.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 155

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

1. Seat the wedge unit on the LC connector.

2. Press the wedge unit first at part 1 and then at part 2 until you hear a click.

3. Place the fiber clamp release tool at the hole on the connector and slide it to
withdraw the fiber clamp.

4. Pull out the optical fiber.

CAUTION

If the length of the bare fiber without coating is less than 10 mm, it can be
determined that the fiber is broken inside the connector. In this case, the
connector can no longer be used.

----End

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 156

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

3.8.5.2 Assembling Optical Fibers in the First-Generation Hybrid Cable in

Fusion Splicing Mode

Context
Optical fibers in the first-generation hybrid cable can be assembled in either of
the two modes: mechanical splicing and fusion splicing.

● In mechanical splicing mode, LC connectors in the purchased 02233FKY or

02233FLA auxiliary material package are used to terminate optical fibers.
● In fusion splicing mode, optical fibers are fusion spliced with fiber pigtails in
the purchased 02233FLA or 02233FLB auxiliary material package, without the
need of LC connectors.

Procedure
Step 1 Feed one end of an optical fiber and one end of a pigtail through the caps of a
fusion splice protection sleeve.

Step 2 Assemble the optical fiber. Remove the fiber jacket and fiber coating in the same
way as in the mechanical splicing scenario.
NOTE

If no 02233FKY or 02233FLA auxiliary material package is purchased, you can use fiber
stripper pliers.

Step 3 Process the pigtail. Use fiber stripper pliers to strip a pigtail, cut off the unwanted
aramid yarn, strip the fiber coating, and route the pigtail into the heat shrink
tubing.

Step 4 Clean bare fibers in the optical fibers and pigtails with pure alcohol using fiber
cleaning papers.

Step 5 Cut the optical fiber and pigtail. Place the fiber holder on the fiber cleaver and use
the trough matching the optical fiber and pigtail.
1. Use a 0.9 mm trough for the pigtail.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 157

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

2. Use a 0.25 mm trough for the optical fiber.

Step 6 Fusion splice the optical fiber and pigtail. Place the optical fiber and pigtail on the
fiber fusion splicer, while ensuring that they do not outreach the electrodes.

NOTE

Test the insertion loss of the spliced optical fiber. If the value is greater than 0.05 dB, repeat
the preceding fusion splicing operations. (The fiber fusion splicer will display the cause,
such as uneven end face, bubbles, or fiber core damage.)

Step 7 Heat the heat shrink tubing. Cover the splicing point with the heat shrink tubing,
secure the heat shrink tubing to the heat shrink trough, and start heating.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 158

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

Check whether the heat shrink tubing is tightly wrapped around the jacket of the optical
fiber. If not, continue to heat it.

Step 8 Assemble the fusion splice protection sleeve. Place the spliced optical fiber into the
fusion splice protection sleeve, and tighten the caps at both ends.

CAUTION

Ensure that the heat shrink tubing has cooled down before you assemble the
fusion splice protection sleeve.

Step 9 Repeat steps 1 to 8 to fusion splice the other optical fiber.

----End

3.8.5.3 Assembling Copper Cores in the First-Generation Hybrid Cables

Context
Copper cores in a hybrid cable need to be terminated by RJ45 connectors before
being connected to devices.
No screw is required to assemble RJ45 connectors. Figure 3-52 shows the
appearance of a screw-free RJ45 connector.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 159

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-52 Screw-free RJ45 connector

1. Lever 2. Cable inlet (3) Observation window

Procedure
Step 1 Strip 8 mm of the insulation layer off each copper core.

Step 2 Raise the levers of an RJ45 connector.

Step 3 Insert the copper cores all the way into the cable inlets. Ensure that no copper
conductors are bent or exposed.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 160

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

CAUTION

Connect the copper cores of the corresponding colors to the positive (+) and
negative (-) terminals on a connector by following the routing requirements for
specific colors of cables in the local country or region. Ensure that both ends of a
single copper core are connected to the same type of terminals (positive or
negative).

Step 4 Lower the levers and look through the observation windows to verify that the
springs do not overlap with the insulation layers.

Step 5 Pull each copper core with a force of about 10 N and ensure that each copper core
is properly connected. Bind the copper cores with cable ties in the same direction
and cut off the excess cable ties.

----End

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 161

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

3.8.6 Connecting the First-Generation Hybrid Cables

Context
For details related to precautions for using the first-generation hybrid cables, see
3.8.5 Assembling the First-Generation Hybrid Cables.

NOTE

Connectors at two ends of each optical fiber in a hybrid cable must be connected to the TX
and RX ports on optical modules, one end to a TX port and the other end to an RX port.
Optical fibers in all hybrid cables must be connected according to the same rules. Table
3-21 provides the recommended connection rules.

Table 3-21 Recommended optical fiber connections

Optical Fiber Color Optical Module on a Optical Module on an

Switch AP

Blue TX RX

Yellow RX TX

Procedure
Step 1 Assemble and test hybrid cables according to 3.8.5 Assembling the First-
Generation Hybrid Cables.

Step 2 Remove dust plugs from the optical ports on a switch and an AP, and install
optical modules (only SFP-10G-iLR-S optical modules are supported). For details,
see 3.6.5 Installing an Optical Module.

Step 3 Connect the RJ45 connector at one end of each hybrid cable to a multi-GE port on
the switch, and then connect the LC connectors at the same end to the RX and TX
ports of an optical module installed on the switch. To ensure convenient cabling, a
hybrid cable must be connected to a multi-GE port and an optical port with the
same number.

CAUTION

When connecting optical fibers, ensure that the bending of optical fibers at the
end of LC connectors does not exceed 180°.

Step 4 Connect the RJ45 connector at the other end of the hybrid copper-fiber cable to
the PoE port on the AP, and connect the LC connector at the same end to the TX
and RX ports on the optical module installed on the AP.

Step 5 Route the cables according to the cabling requirements in 3.8.5 Assembling the
First-Generation Hybrid Cables, and then use cable ties to bind the cables.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 162

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

In mechanical splicing scenarios, reserve at least 90 mm cabling space between the inner
side of the cabinet door and the front panel of the switch. In fusion splicing scenarios,
minimize the pigtail length and reserve sufficient cabling space based on the pigtail length.

Step 6 Attach a label to each cable.

Figure 3-53 Connections of the first-generation hybrid cable

1. Multi-GE port on a switch 2. 10GE/GE SFP+ port on a switch

3. PoE_IN port on an AP 4. Uplink 10GE/GE SFP+ port on an AP

----End

3.8.7 Assembling Second-Generation Hybrid Cable

Context
The second-generation hybrid cable (hybrid cable 2.0) is composed of optical
fibers and copper cores. It is mainly used to connect a hybrid optical-electrical
switch to an AP or remote unit so that the switch can provide power and transmit
data for the AP or remote unit. During construction, onsite cable connection is
required.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 163

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTICE

● Do not stretch, step on, or place heavy objects on hybrid cables 2.0. Keep the
cables away from sharp objects. A maximum of 100 hybrid cables 2.0 can be
bundled when no pipe is used. When a pipe is used, ensure that one-third space
inside the pipe is vacant.
● Cabling is allowed only when communication facilities are available. Preparing
cables onsite must be performed with no power supply connected. After hybrid
cables 2.0 are made onside, you are advised to use a red pointer and an optical
fiber adapter to check whether optical fibers are broken or not.
● Route cables according to the planned positions and mark the cables in
advance to eliminate the need to differentiate cables on the switch side after
the cables are routed. Reserve a sufficient length of cable at the end where the
cable label is attached, avoiding cutting off the cable label during cable
assembling.
● When routing hybrid cables 2.0, coil the excess optical fibers around dedicated
devices, such as a fiber management tray. Even force needs to be applied when
cables are coiled to ensure the cables are not overly bent. The bending radius
of a hybrid cable 2.0 is at least five times its diameter. The minimum bending
radius of a branch optical fiber inside a hybrid cable 2.0 is 15 mm.
● Vacant hybrid connectors must be covered with dustproof caps. Ensure that the
end faces of hybrid connectors are clean. When a hybrid connector is installed
or removed, protect its end face from touching other objects, preventing
contamination or damage. If any dirt is found, use alcohol or dust-free paper to
clean it. If the end face is damaged, start from the very beginning to assemble
the pigtail.
● After connecting the pigtails on both sides of a hybrid cable, you need to test
the link loss. If the fiber splicing or cable crimping does not meet the
requirements, you are advised to cut off the connection point between the
main cable and the pigtail and then reconnect them.
● The connector of a hybrid cable 2.0 cannot be inserted into a common optical
module and must be used with a hybrid module (SFP-GE-Hybrid or SFP-10G-
Hybrid).
● After splicing optical fibers and crimping power cables in one hybrid cable are
complete, make another hybrid cable.

Tools and Accessories

Table 3-22 Fusion splicing tools (prepared by the customer)

Tool Appearance Description

Cable Used to peel off the outer

stripper sheath of hybrid cables.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 164

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Tool Appearance Description

Wire stripper Used to peel off the

rubber layer and coating
layer of hybrid cables, and
only involved in fusion
splicing scenarios.

Fiber cleaver Used to cut optical fibers.

Duckbilled Used to remove the

wire stripper rubber layer of copper
cores in hybrid cables.

Fiber - Used to clean optical

cleaning fibers.
paper and
alcohol
(concentrati
on: 99.5%)

Optical fiber Used to fusion splice the

splicer optical fiber and pigtail,
and only involved in
fusion splicing scenarios.

Crimping Used to connect power

tool cables.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 165

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Tool Appearance Description

Long Used to measure

measuring dimensions.
tape

Insulation Used to fix cables or wrap

tape the damaged part for
protection.

Red pointer Used to test the

connectivity of optical
fibers.

Table 3-23 Accessories

Tool Part Appearance Description
Number

Heat 02233PJ Used only in fusion

shrink A splicing scenarios.
tubing

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 166

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Tool Part Appearance Description

Number

Fiber Used only in fusion

splice splicing scenarios.
protect
or

Bare Used to connect power

crimp cables.
termin
al

Procedure
Step 1 Strip the adhesive tape off the main cable and pigtail.

Use a cable stripper to peel off a 300 mm long section of the outer sheath from
one end of a hybrid cable 2.0 for connecting to a switch, and peel off 300 mm
from the other end for connecting to an AP.

NOTICE

Skip this step if the pigtail does not have a rubber layer.

Step 2 Splice the optical fiber.

1. Find two optical fibers from the main cable and pigtail, remove the middle
rubber layer, and cut off the extra aramid yarn to expose the 30 mm long
internal cable.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 167

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

2. Feed an optical fiber through the caps of a fiber splice protector and a heat-
shrink tubing.

3. Use a wire stripper to strip the inner rubber layer and the fiber coating layer
to expose the 25 mm optical fiber. Then, use the fiber cleaning paper dipped
in alcohol to clean the optical fiber.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 168

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 169

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

4. Use a fiber cutter to cut the optical fiber and insert the optical fiber into one
side of the fiber splicer.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 170

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

5. For the pigtails of the same color, put on the caps of a fiber splice protector,
strip the inner rubber layer and the coating layer of the optical fiber, insert
them into the other side of the fiber splicer, and start fiber splicing.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 171

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

6. Use a heat shrink tubing to secure the fiber splicing point.

7. Assemble the fiber splice protector. Place the spliced optical fiber into the
fiber splice protector, and tighten the caps at both ends.

CAUTION

– Ensure that the heat shrink tubing has cooled down before you assemble
the fusion splice protection sleeve.
– For the fiber management tray on the front panel, fiber splicing cannot be
performed with a fiber splice protector. Otherwise, fiber coiling will be
affected.
– If the fiber splicing point is coiled in the fiber management tray, the fiber
splice protector is not required.

8. Repeat the preceding steps to splice the main optical cable and the other
optical fiber in the pigtail.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 172

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 3 Crimp the power cable.

1. Find two power cables from the main cable and pigtail, and strip the
insulation layer to expose a 7 mm copper wire.

2. Insert the copper wires of the power cables of the same color in the main
cable and pigtail into the two ends of the bare crimp terminal, and use the
ratchet crimping pliers to crimp the copper wires.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 173

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 174

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTICE

When crimping a 17 AWG power cable on site, use a pair of pliers with a
cross-sectional area of 1 mm² to 1.5 mm².
When crimping a 21 AWG power cable on site, use the pliers with a diameter
of 0.5 mm², or select the corresponding pliers according to the actual
situation.

When crimping the power cable, ensure that the side of the crimping pliers is
close to the step surface in the middle of the bare crimp terminal. If the
insulation tube of the bare crimp terminal is damaged, wrap the bare crimp
terminal with insulation tape.

In this way, the assembling operation of the hybrid cable 2.0 is completed.

----End

3.8.8 Connecting Second-Generation Hybrid Cable

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 175

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Context
For details related to precautions for using the second-generation hybrid cable
(hybrid cable 2.0), see 3.8.7 Assembling Second-Generation Hybrid Cable. A
hybrid optical-electrical switch can be directly connected using hybrid cables or
connected to an HDF.

Table 3-24 Connection scenario using hybrid cable 2.0

Scenario Connection Description

Direct connection Splice the pigtail on the switch side to

the main cable and directly connect
the pigtail to the switch.
If no HDF is used, place the main cable
and splicing part of the pigtail into the
fiber splice tray to prevent the spliced
cable from being damaged or
contaminated.
The customer needs to prepare the
fiber splice tray. It is recommended
that the fiber splice tray be installed
near the hybrid optical-electrical
switch in the cabinet.

HDF-based connection Splice the pigtail on the switch side to

the main cable and directly connect
the pigtail to the HDF. The HDF and
switch are connected using jumpers.

Figure 3-54 Appearance of a fiber splice tray

For details about how to splice pigtails in the direct connection scenario, see 3.8.7
Assembling Second-Generation Hybrid Cable. The cabling method on the switch

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 176

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

port side is the same as that in the scenario where an HDF is used. The following
uses the HDF as an example.

The HDF and switch can be installed in the same cabinet or in different cabinets,
and jumpers of different lengths are used. The procedure for installing the HDF
and switch in the same cabinet using 1.5 m and 0.3 m jumpers is used as an
example.

Table 3-25 HDF-based connection

HDF-Based Connection Cable Connection

Requirements

The HDF and switch are 0.3 m jumper The recommended

installed in the same distance between the
cabinet. hybrid optical-electrical
switch and the HDF is 1
U to 3 U.

1.5 m jumper The recommended

distance between the
hybrid optical-electrical
switch and the HDF is 14
U to 16 U.

3 m jumper The recommended

distance between the
hybrid optical-electrical
switch and the HDF is 17
U to 40 U.

The HDF and switch are 7 m jumper -

installed in different
cabinets.

NOTE

Connectors at two ends of each optical fiber in a hybrid cable must be connected to the TX
and RX ports on optical modules, one end to a TX port and the other end to an RX port.
Optical fibers in all hybrid cables must be connected according to the same rules. Table
3-26 provides the recommended connection rules.

Table 3-26 Recommended optical fiber connections

Optical Fiber Color Optical Module on a Optical Module on an

Switch AP

Blue TX RX

Yellow RX TX

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 177

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Procedure
Step 1 Prepare and test the hybrid cable 2.0 according to 3.8.7 Assembling Second-
Generation Hybrid Cable.

Step 2 Connect the 1.5 m jumper.

1. Install the switch and HDF in the cabinet. It is recommended that the distance
between the HDF and the slot where the hybrid optical-electrical switch is
installed be 14 U to 16 U.
NOTE

– If multiple switches and HDFs need to be installed in a cabinet, plan the

installation position of each device in the cabinet in advance.
– The distance between two HDFs must be greater than 1 U.
– It is recommended that switches connected to hybrid cables be installed at an
interval of 1 U to facilitate cable insertion and removal.
2. Lead the jumper into the cabling space on the side of the cabinet.
3. Insert the copper module into the port on the hybrid optical-electrical switch.
4. Remove the dustproof cap from of the optical connector. Connect the jumper
to the corresponding ports on the HDF and hybrid optical-electrical switch.
During the connection, ensure that the port numbers on the HDF are the
same as those on the switch.
5. Connect the main cable with the pigtail spliced to the corresponding port at
the rear of the HDF.
6. Connect the jumpers to other ports in the same way, and then use cable ties
to fix the jumpers. If there are more than 24 cables, route them along both
sides of the cabinet. The cabling mode can be left-right or top-bottom.

Table 3-27 Cabling mode

Cabling Precaution

Left-right cabling Vertical distance between the switch

front panel and the inner side of the
cabinet door: ≥ 110 mm
If each switch requires 48 ports in
full configuration, it is
recommended that the vertical
distance between the front panel of
the switch and the inner side of the
cabinet door be greater than or
equal to 110 mm. If the distance
does not meet requirements, you are
advised to use the top and bottom
cabling mode.

Top-bottom cabling The distance between two HDFs or

switches must be greater than 1 U.

Step 3 Connect the 0.3 m jumper.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 178

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

1. Install the switch and HDF in the cabinet. It is recommended that the distance
between the HDF and the slot where the hybrid optical-electrical switch is
installed be 3 U.
2. Insert the copper module into the port on the hybrid optical-electrical switch.
3. Remove the dustproof cap from of the optical connector. Connect the jumper
to the corresponding ports on the HDF and hybrid optical-electrical switch.
4. Connect the main cable with the pigtail spliced to the corresponding port at
the rear of the HDF.
5. Connect the jumpers to other ports in the same way, and then use cable ties
to fix the jumpers. You are advised to use velcro straps to fix cables.

----End

3.9 Post-installation Checks

Table 3-28 lists the post-installation items to be checked.

Table 3-28 Post-installation checklist

No. Check Item Method

1 The installation position of the device meets the Observe

requirement in the associated engineering design
document.

2 The surfaces of the device are clean and smooth, Observe

free from fingerprints, stains, and scratches.

3 Components are correctly installed in the cabinet. Observe

No component is loose or damaged.

4 All screws are correctly tightened. Observe

5 There are no objects on the chassis. Observe

6 Leave at least 50 mm (2.0 in.) clearance around Measure

the device for heat dissipation. Do not install a
device with its air intake vent facing or close to
the air exhaust vent of other devices.

7 Signal cables are not damaged or broken and Observe

have no splices.

8 Signal cable connectors are clean, intact, and Observe

correctly connected. Wires of each signal cable
are securely clamped in the connectors.

9 Each signal cable has labels attached at both Observe

ends, with clear text facing the same direction.

10 The power cables and ground cable are all Observe

copper wires, and are not spliced or damaged.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 179

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

No. Check Item Method

11 The power cables and ground cable are routed in Observe

compliance with the associated engineering
design document and meet the power
distribution requirements.

12 The power cables and ground cable are securely Observe

connected in compliance with regulations.
Ground cable lugs are protected with spring
washers on flat washers.

13 The power cables and ground cable are Observe

separated from the signal cables.

14 The power cables and ground cable are routed Observe

straightly and bundled neatly. Sufficient slack is
left at the bent part of the cables.

15 Optical fibers routed out of the cabinet are Observe

protected. For example, they are routed in a
corrugated pipe or trough.

16 The bend radius of optical fibers is 20 times Measure

larger than their diameter. Generally, the bend
radius is larger than 40 mm.

17 Optical fibers are bundled neatly using binding Observe

tape with suitable force.

18 No signal cables are routed near the heat vents Observe

on the cabinet.

19 Cables in the cabinet do not cross each other and Observe

cables outside the cabinet are bundled.

3.10 (Optional) Installing an RPS1800

3.10.1 Installing the RPS1800 in a Cabinet or Rack

An RPS1800 is a redundant power supply system that provides power redundancy

for connected switches to ensure uninterrupted services. When the internal power
supply of a switch fails, the RPS1800 detects the power failure and supplies power
to the switch immediately. This allows the switch to continue operating, thereby
ensuring service continuity.

The RPS1800 can be installed in a cabinet or rack only. The installation procedure
is the same as that used for a switch of the same dimensions, which are (H x W x
D) 43.6 mm x 442.0 mm x 310.0 mm (1.72 in. x 17.4 in. x 12.2 in.). For details, see
3.5.2.1 Using Front Mounting Brackets.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 180

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTICE

● Before the installation, take ESD protective measures, for example, wear ESD
gloves or an ESD wrist strap.
● Leave at least 50 mm (2.0 in.) clearance around the device for heat dissipation.
Do not install a device with its air intake vent facing or close to the air exhaust
vent of other devices.
● Align the mounting brackets on the left and right mounting rails. If they are
not on a horizontal line, forcibly mounting the RPS1800 may distort the chassis.

3.10.2 Installing a Power Module in the RPS1800

Context
An RPS1800 that has 870 W PoE power modules installed can provide PoE power
redundancy or PoE power supply for a PoE switch, as shown in Figure 3-55.

Figure 3-55 RPS1800 providing PoE power for connected switches

NOTE
When providing power for non-PoE switches, the RPS1800 does not need 870 W PoE power
modules. The 870 W PoE power modules and RPS cables are not hot swappable.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 181

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Tools and Accessories

● ESD wrist strap or ESD gloves

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.
Step 2 Remove the filler panel from the slot into which the power module will be
installed. Keep the filler panel for future use.
Hold the upper edge of the filler panel and pull the filler panel downward to
remove it. Do not pull the filler panel horizontally.

Step 3 Install the power module.

1. Slide to left the white button on the power module and pull out the handle.

2. Insert the power module into the slot and push the handle inward.

3. Slide to right the white button.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 182

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE
To remove the power module, reverse this procedure.

----End

3.10.3 Connecting the RPS1800 to a Switch

Context
The RPS1800 can connect to a maximum of six switches and ensure seamless
failover for one switch if the internal power module of the switch fails. Among the
six DC output ports, port 1 has the highest priority. The switch connected to port 1
preferentially receives power from the RPS1800.

If the RPS1800 uses the same external power supply system as the connected
switches, it can prevent service interruption caused by failures of the switches'
internal power modules. However, for improved reliability, if the RPS1800 uses a
different external power supply system than the connected switches, it can
prevent service interruption caused by failure of internal power modules and
external power supply systems of the switches.

DANGER

Ensure that the power is off before connecting power cables.

NOTICE

● Power cables of the RPS1800 must be routed indoors or buried underground if

they are led in from the outside. Do not aerially route the power cables
outdoors.
● Do not power on the switch until you finish installing the switch and
connecting all cables.
● Power cables delivered with a switch are for use with this switch only.

Tools and Accessories

● ESD wrist strap or ESD gloves

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 183

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

● Phillips screwdriver
● RPS cable
● RPS AC power cable

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.

Step 2 Connect an RPS cable to the RPS1800.

1. Insert one end of the RPS cable into an output port on the RPS1800 according
to the networking plan. Ensure that the top side of the plug (marked "TOP")
faces up.
2. Tighten the captive screws on the plug.

Figure 3-56 Connecting an RPS cable to the RPS1800

Step 3 Connect the RPS cable to a switch.

1. Insert the other end of the RPS cable to the RPS input port at the rear of the
switch. Ensure that the top side of the plug (marked "TOP") faces up.
2. Tighten the captive screws on the plug.

Figure 3-57 Connecting the RPS cable to a switch

Step 4 Connect the RPS1800 power cable to the RPS1800.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 184

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

The RPS1800 uses a C19 straight female to PI angle male AC power cable, as
shown in Figure 3-58. An RPS1800 power cable is connected in the same way as
the AC power cable of a switch. For details, see 3.8.1 Connecting Power Cables.

Figure 3-58 RPS1800 power cable

Step 5 Connect the RPS1800 power cable to an external power supply system.
The power cables of the RPS1800 and switch can be connected to the same or
different external power supply systems, as shown in Figure 3-59 and Figure
3-60, according to power reliability requirements.

Figure 3-59 Connecting the RPS1800 and switch to the same external power
supply system

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 185

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-60 Connecting the RPS1800 and switch to different external power
supply systems

----End

3.11 Powering on a Switch for the First Time

Tools and Accessories

● ESD wrist strap or ESD gloves
● Multimeter

Procedure
Step 1 Perform the following checks before powering on a switch:
1. Use a multimeter to check that there is no short-circuit condition between the
phase wire (live wire), ground wire, and neutral wire in each power outlet.
2. Use the multimeter to check that the input voltage provided by the external
power supply system is within the operating voltage range for the switch. For
the operating voltage range, see 3.3.4 Checking the Power Supply System.
3. Check that the power switches of the external power supply system and the
switch or the power module are both turned off.
4. Check that the power cables are correctly connected.

Step 2 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.

Step 3 Turn on the external power supply system connected to the switch.

Step 4 Turn on the power switch on the switch or power module.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 186

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTE

Skip this step if the switch does not support pluggable power modules or does not have a
power switch.

Step 5 After the switch completes its startup, check the indicators on the switch and
power modules.

For details about the indicators of specific switch models, see the Hardware
Description.

----End

Follow-up Procedure
To power off the switch, perform the following steps:

NOTICE

Powering off the switch will interrupt all services on the switch. Exercise caution
when you perform this operation.

1. Turn off the power switch on the switch or power module.

2. Turn off the external power supply system connected to the switch.
3. Check that the switch and all its modules are powered off. (All indicators are
off.)

3.12 First Login to a Device

Before configuring services on a new device, you need to log in to the device
locally. Once logging in, you can configure the device name, management IP
address, and system time, and configure Telnet or STelnet to implement remote
management.

The first login methods and procedures supported by a device vary according to
the device model and software version. For details, see the configuration guide of
the corresponding model and version.

Table 3-29 Configuration guide links

Model Configuration Guide (Example)

S1700 unmanaged Unmanaged switch models, requiring no

switches configuration

S1700 web-managed S1700 V200R022C00 Web User Guide

switches and fully-
managed switches

S200 S200 V200R022C00 Web User Guide

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 187

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Model Configuration Guide (Example)

S300, S500, S2700, S300, S500, S2700, S5700, and S6700

S5700, and S6700 V200R022C00 Configuration Guide - Basic
running V200 Configuration

S5700 and S6700 S5700 and S6700 V600R022C00 Configuration

running V600 Guide - Basic Configuration

S3710 running V600 S3700 V600R022C10 Configuration Guide - Basic

Configuration

3.13 Component Replacement

NOTICE

Before sending a switch for repair or discarding it, format its flash storage to
ensure data security and reset its BootLoad menu password.

When installed in a normal operating environment, fixed switches do not need

dust cleaning. Do not disassemble the equipment.

Some switch models provide the JTAG function through edge connectors on the
PCB, as shown in Figure 3-61. The JTAG function is used for equipment checks
and fault diagnosis during maintenance.

Figure 3-61 Edge connectors

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 188

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

If the device is faulty, fill in the Repair Transmission Sheet and send the faulty
module with the Repair Transmission Sheet to the equipment supplier or the
specified repair service provider.

3.13.1 Replacing a Power Module or Fan Module

Context
This section describes how to replace a power module. The procedure for replacing
a fan module is similar. All the power modules and fan modules are hot
swappable (except the 870 W PoE power module).

NOTICE

● Before replacing a power module, ensure that the switch is powered by the
other power module. Replacing the only power module of a switch will
interrupt services.
● If two power modules are installed in a switch, they work in 1+1 backup mode.
If three power modules are installed in a switch, they work in 1+1+1 backup
mode. Replacing one power module will not power off the switch. If you are
replacing both power modules, replace the second one only after the first
replaced one starts to work (its indicator is steady green).
● If a fan module needs to be replaced, complete the replacement procedure
within 3 minutes.
● Fan modules of different types or with different airflow directions cannot be
used on the same switch.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.
Step 2 Turn off the power module.
Step 3 Remove the power cable from the power module. The procedure for removing a
power cable is the reverse of the procedure for installing the power cable. For
details, see 3.8.1 Connecting Power Cables.
Step 4 Remove the power module from the switch.
● To remove the power module secured by a captive screw, perform the
following steps:
a. Use a Phillips screwdriver to loosen the captive screw on the power
module counterclockwise.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 189

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

b. Slowly pull the power module out by the handle.

● To remove the power module secured by a lock, perform the following steps:
a. Press and hold the lock on the power module in the direction shown in
the figure.
b. Slowly pull the power module out by the handle.

Step 5 Install the replacement power module in the switch. For details, see 3.6.1
Installing a Pluggable Power Module.

Step 6 Connect the power cable to the new power module. For details, see 3.8.1
Connecting Power Cables.

Step 7 Turn on the power module. (Skip this step if the power module does not have a
power switch.)

Step 8 Use either of the following methods to check whether the new power module is
working normally:
● Observe the STATUS indicator on the panel. If the indicator is steady green,
the power module works normally.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 190

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

● Run the display device command to check the running status of the new
power module.

----End

Follow-up Procedure
If the new power module does not work normally, contact the equipment supplier
or local maintenance personnel for technical support.
After replacing the power or fan module, collect all tools. If the old power or fan
module is faulty, fill in the Repair Transmission Sheet and send the faulty
module with the Repair Transmission Sheet to the equipment supplier or the
specified repair service provider.

3.13.2 Replacing an Optical Module

Context

CAUTION

Never look directly into an optical module or the ends of optical fibers. Optical
modules and connected fibers emit laser radiation that will cause eye damage.

NOTICE

Use optical modules certified for Huawei switches. Using other optical modules
may affect service stability and Huawei can accept no liability for the outcome.

NOTICE

Ensure that the new optical module has the same center wavelength and complies
with the same standards as the old one.

NOTICE

Optical modules are electrostatic-sensitive components. Take ESD protection

measures when replacing optical modules.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 191

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTICE

● Unplug the optical fibers from the optical module before removing it. Install or
remove optical fibers carefully to avoid damaging the fiber connectors.
Applying too much force to the optical fibers may damage the optical module.
● If an optical module cannot be completely inserted into an optical port, turn
the optical module over and try again.
● Cover unconnected optical modules with dust plugs.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Dust caps
● Dust plugs
● Alcohol swab

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. Ensure that the ESD wrist strap is
grounded and in a close contact with your wrist.

Step 2 Record the location of each optical fiber on the old optical module and check
whether the labels on the optical fibers are correct and clear. If any labels are
unclear, replace them and ensure that the details are correct.

Step 3 Release the locking clip on the fiber connector, gently push the fiber connector
inward, and then pull out the optical fiber. After removing the optical fibers from
the optical module, cover the connectors with dust caps.

The locking clip varies on different fiber connectors.

● Figure 3-62 shows the locking clips on an LC/PC connector. Hold down the
locking clips when pulling the optical fibers.
● Figure 3-63 shows the locking clip on an MPO connector. The locking clip is
released automatically when you pull the MPO connector.
● Figure 3-64 shows the locking clip on an SC/PC connector. The locking clip is
released automatically when you pull the SC/PC connector.

Figure 3-62 LC/PC connector

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 192

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Figure 3-63 MPO connector

Figure 3-64 SC/PC connector

Step 4 Remove the optical module and cover the bores with dust plugs. Store optical
module safely.
The latch varies on different optical modules. Figure 3-65 shows an optical
module with a clasp latch. To release the clasp latch, rotate it down. Figure 3-66
shows an optical module with a tab latch. The tab latch is released when you pull
it.

Figure 3-65 Optical module with a clasp latch

Figure 3-66 Optical module with a tab latch

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 193

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Step 5 Take out the new optical module from the package. Ensure that the optical
module is correctly oriented and gently push it into the optical port until you hear
a click.
NOTE

The new optical module must have the same optical parameters as the remote optical
module connected to it.

Step 6 Identify the optical fibers to be connected to the optical module. Remove the dust
caps from the optical fibers and insert the optical fibers to the bores of the optical
module.

----End

Follow-up Procedure
If the new optical module does not work, unplug the optical fibers and clean their
connectors in one direction with an alcohol swab. Then, re-connect them. If this
fails to resolve the issue, contact the equipment supplier or local maintenance
personnel for technical support.

3.13.3 Replacing a Card

Context
Some switch models support pluggable interface cards. This section describes how
to replace a 4-port front card. The replacement method is the same for other
cards. For details about which models support what cards, see "Cards" in the
Hardware Description.

NOTICE

Only switch models S5700-SI, S5710-LI, and S5700-EI do not support hot
swappable cards. To replace cards of this switch models, power off the switch
before removing the card from the switch.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.

Step 2 If the card you want to replace is not hot swappable, power off the switch.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 194

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

NOTICE
Powering off the switch will interrupt all services on the switch. Exercise caution
when performing this operation.

Step 3 Remove the card from the switch.

1. Use a Phillips screwdriver to loosen the captive screws at two sides of the
card.
2. Rotate the ejector lever outward to release the card from the slot.
3. Holding the two sides of the card, gently slide the card out of the slot.

Step 4 Install the new card. For details, see 3.6.4 Installing a Card.

----End

Follow-up Procedure
If the new card does not work normally, contact the equipment supplier or local
maintenance personnel for technical support.

After replacing the card, collect all tools. If the old card is faulty, fill in the Repair
Transmission Sheet and send the faulty module with the Repair Transmission
Sheet to the equipment supplier or the specified repair service provider.

3.13.4 Replacing a Switch

Context
The chassis is severely damaged or a hardware fault occurs due to external forces.

NOTICE

Power off the switch before replacing it, which will interrupt services.

Tools and Accessories

● ESD wrist strap or ESD gloves
● Phillips screwdriver

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 195

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

Procedure
Step 1 Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure
that it is in close contact with your wrist and grounded properly.
Step 2 Confirm that the names, models, and specifications of the new and original
switches are the same. If a mismatch is found, contact technical support as soon
as possible.
Step 3 Record the IDs of slots where modules are installed and cable connections on
ports of the original switch.
Step 4 Back up configuration data of the original switch as follows: Run the save
command to save configuration data into a configuration file on the storage
medium, and copy the configuration file to a maintenance terminal (skip this step
for the unmanaged switch).
Step 5 Power off the original switch.

CAUTION

The switch is successfully powered off when all indicators are off.

Step 6 Remove all cables and pluggable modules from the switch.
Step 7 Remove M6 screws from the mounting brackets and remove the switch from the
cabinet (skip this step if the switch is installed on the desktop).

CAUTION

When removing screws from the mounting brackets, hold the bottom of the
switch to prevent it from falling down to cause personnel injury or damage to
other devices.

Step 8 Remove mounting brackets from the original switch and install the mounting
brackets on the new switch.
Step 9 Install the new switch in the same position as the original switch and secure it
with M6 screws.
Step 10 Install the original modules and cables according to the recorded information.
Step 11 Power on the new switch and observe indicators on it. For details about the
indicators of specific switch models, see the Hardware Description.
Step 12 Log in to the new switch and check whether the switch is working properly.
Run the display device command to check the running status of the new switch.

----End

Follow-up Procedure
If the new switch does not work normally, contact the equipment supplier or local
maintenance personnel for technical support.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 196

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches 3 Hardware Installation and Component
Hardware Installation and Component Replacement Replacement (Fixed Switches)

After the replacement is complete, collect all tools. When you confirm that the
replaced switch is faulty, fill in the Repair Transmission Sheet and send the faulty
switch and the sheet to Huawei.

3.13.5 3D Videos for Parts Replacement

Table 3-30 3D Videos for Parts Replacement
Scenario Link of Video

Replacing an ES0W2PSA0150 Power Replacing an ES0W2PSA0150 Power

Module Module

Replacing a FAN-028A-B Fan Module Replacing a FAN-028A-B Fan Module

Replacing an ES5D21X04S01 Card Replacing an ES5D21X04S01 Card

Replacing an ES5D21X02T01 Card Replacing an ES5D21X02T01 Card

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 197

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

4 Appendix

4.1 Appendix A On-site Cable Assembly and Installation

4.2 Appendix B Environmental Requirements for Device Operation
4.3 Appendix C Equipment Grounding Specifications
4.4 Appendix D Engineering Labels for Cables
4.5 Appendix E Guide to Using Optical Modules
4.6 Appendix F Fault Tag

4.1 Appendix A On-site Cable Assembly and

Installation

4.1.1 Cable Assembly Precautions

Checking the Appearance of Cables

● If the cable jacket or insulation is visibly dirty, clean it before assembly.
● If the jacket or insulation of a cable has visible damage, irreparable scuffing,
or other defects, do not use the cable.
● If the shield layer of a cable is damaged, do not use the cable.
● If the cable jacket or insulation cracks after the cable is bent or twisted,
discard this cable and check whether other cables have the same problem. If
other cables have the same problem, replace these cables.

Checking the Appearance of Connectors

● Do not use connectors with visible defects, damage, rust or scuffing.
● Do not use connectors if their shells or pins have exposed part or uneven
plating, or their pins are lost, broken, or bent.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 198

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

● Do not use connectors that have dirt on their pins or in their jacks or if there
are conductors between pins or between pins and the shell.

Precautions for Assembly

● Use dedicated tools or tools delivered by Huawei and follow the methods
given here during assembly.
● Hold terminals of cables instead of pulling the cables themselves when
installing or removing cable components.
● Take the following precautions when cutting or stripping cables:
– Make cables slightly longer than necessary.
– Coil cables longer than 2 m (6.56 ft) after cutting. Bind and fasten the
coils using bundling ropes. The inner diameters of the coils should be
larger than 20 times the outer diameters of the cables.
– When stripping the jackets of cables, avoid damaging the shield layers
(braid or aluminum foil), insulation, core conductors, and other jackets
that do not need to be stripped.
– After assembling cables, cut all visible cross sections of jackets to ensure
that the cross sections are arranged neatly.
– Do not touch the core conductors of cables with your hands. Terminate
exposed conductors in a timely way after stripping off insulation so that
the surface of the conductors does not become oxidized.
● Take the following precautions when crimping and connecting cables or
connectors:
– The terminals and conductors should be connected tightly after they are
crimped. They should not be moved or turned.
– Cut all the exposed copper wires.
– Try to avoid a second crimping of sleeves.
– Keep all the conductors clean and aligned.
NOTE

The connectors, cables, and tools provided by different vendors may be different. The
figures in this document are for your reference only.

4.1.2 Installing Cable Accessories

4.1.2.1 Precautions for Installing Cable Accessories

Tools
Use dedicated tools provided or specified by Huawei and follow the installation
procedure described here.

NOTE

The illustrations in this document may differ from actual situations, but the installation
methods are the same. For example, in this document, the adapters of cable connectors
have separate interfaces. In the actual situation, the adapters may have interfaces fixed on
equipment.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 199

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Bending Radius
Unless otherwise specified, bending radius (R) of cables or fibers must meet the
requirements listed in Table 4-1.

Table 4-1 Bending radius of cables or fibers

Cable or Fiber Bending Radius (R)

Ordinary cable In normal cases, R ≥ 2d. When the

cable is connected with a connector, R
≥ 5d.

Fiber R ≥ 40 mm (1.57 in.); Bending angle >

90°

NOTE

The letter d indicates the diameter of a cable or fiber.

Precautions for Installation

● Hold terminals of cables instead of pulling the cables themselves when
installing or removing cable components.
● Do not insert a connector forcibly when the connector is blocked. Use a
dedicated tool to pull out the connector. Install the connector again after you
check that the pins are inserted properly.
● Before tightening screws on cable connectors, ensure that the connectors are
properly connected to their adapters. Tighten the screw with appropriate force
using a flat-head or Phillips screwdriver instead of bare hands or an electric
screwdriver. If the screw cannot be screwed into the tapped hole, determine
the reason and try again. Do not apply too much force, or the screw or
adapter may be damaged.
● When removing densely aligned cables or fiber connectors, use dedicated
pliers such as cable-pulling pliers and fiber-pulling pliers.
● Do not twist, bend, stretch, or extrude fibers during installation.
● Cover the idle fiber connectors with dust caps. Remove the dust caps before
using the fiber connectors.

Requirements for Cable Routing

● To protect cables, remove the burrs in the cable through-holes or install
protective rings in the holes.
● To ease the connection and to avoid stress, keep cable joints slack. After
connecting multiple cables to a connector that has multiple interfaces, keep
the cables slack to avoid generating stress.
● Bind or clean cables gently because cable distortion affects signal quality.
● Keep cables away from moveable components such as doors.
● Sharp objects must not touch cable wiring to prevent damage to cables.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 200

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

● To protect power cables, route power cables of the active and standby power
modules separately.

4.1.2.2 Installing Power Adapters

4.1.2.2.1 Installing the OT Terminal

Procedure
● Install an OT terminal.
a. Align the hole of the OT terminal (conductor upward) with a connecting
hole, as shown in Figure 4-1.

Figure 4-1 Aligning the OT terminal with a connecting hole

NOTE

When you install an OT terminal, the crimping sleeve is installed as shown in

Figure 4-2, where A is correct and B is incorrect.

Figure 4-2 Installing an OT terminal, showing the orientation of crimping

sleeve

b. Place the spring washer and flat washer in turn, mount a matching screw,
and fasten it clockwise, as shown in Figure 4-3.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 201

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Figure 4-3 Installing two terminals back to back

NOTICE

Ensure that the OT terminal is not in contact with other terminals or

metal components.

c. Move the cable slightly and ensure that it is securely connected, as shown
in Figure 4-4.

Figure 4-4 Installed OT terminal

● Install two OT terminals on a post.

Before you install two OT terminals on a post, ensure that the two terminals
can be installed on the post and that the electrical connecting pieces have a
large contact area. Two OT terminals can be installed using any of these
methods:

– Bend the upper OT terminal at a 45- or 90-degree angle, as shown in

Figure 4-5.
– Cross the two terminals, as shown in Figure 4-6.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 202

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Figure 4-5 Bending the upper OT terminal at a 45- or 90-degree angle

Figure 4-6 Crossing two terminals

NOTICE

If the two terminals are different sizes, place the smaller one above the
bigger one. A maximum of two terminals can be installed on a post.

● To remove an OT terminal, loosen the screw counterclockwise.

----End

4.1.2.2.2 Installing the Cord End Terminal

Procedure
Step 1 Hold a cord end terminal upright and place it on a terminal jack, as shown in
Figure 4-7. To ensure bump contact and dense connection, place the plain side of
the terminal outwards.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 203

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Figure 4-7 Placing a terminal on a terminal jack vertically

Step 2 Insert the terminal into the jack vertically, and turn the screw clockwise to fasten
the terminal, as shown in Figure 4-8.

Figure 4-8 Feeding the terminal into the jack

NOTICE

● Ensure that the exposed section of the terminal is less than 2 mm (0.079 in.) in
length.
● Do not press the insulation of the terminal.
● Insert only one terminal into one jack.

Step 3 Move the cable slightly and ensure that it is securely connected.
Step 4 Before you remove a cord end terminal, loosen the screw counterclockwise.

----End

4.1.2.3 Installing Fiber Connectors

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 204

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Context

NOTICE

● After you remove the dustproof cap, ensure that the fiber pins are clean and
install them as soon as possible.
● When you disassemble fiber connectors, you must use a dedicated tool if the
connectors are densely installed.

4.1.2.3.1 Cleaning Fiber Connectors

Procedure
Step 1 Clean the pins of a fiber connector by using lint-free cotton and alcohol.

Step 2 Clean the pins again by using dust-free cotton. If necessary, clean the pins by
using an air gun. Ensure that the pins are free from any fiber or debris.

----End

4.1.2.3.2 Installing an LC Fiber Connector

Procedure
Step 1 Remove the dustproof cap of the LC fiber connector and store it for future use.

Step 2 Align the core pin of the male connector with that of the female connector, as
shown in Figure 4-9.

Figure 4-9 Aligning the male connector with the female connector

Step 3 Align the male connector with the fiber adapter and gently push the male
connector until it is completely seated in the fiber connector, as shown in Figure
4-10.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 205

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Figure 4-10 Feeding the male connector into the female connector

Step 4 A clicking sound indicates that the male connector is locked, as shown in Figure
4-11.

Figure 4-11 Installed LC connector

Step 5 To disassemble an LC fiber connector, press the locking nut to release the locking
clips from the bore, and gently pull the male connector, as shown in Figure 4-12.

Figure 4-12 Disassembling an LC fiber connector

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 206

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

----End

4.1.2.3.3 Installing the SC Fiber Connector

Procedure
Step 1 Remove the dustproof cap of the SC fiber connector and store it for future use.
Step 2 Align the core pin of the male connector with that of the female connector, as
shown in Figure 4-13.

Figure 4-13 Aligning the male connector with the female connector

Step 3 Feed the fiber connector into the female connector, with your fingers holding the
shell of the fiber connector (not the pigtail). When you hear a click, the fiber
connector is secured by the clips (internal parts, not illustrated in the figure). Pull
the fiber connector gently. If the connector does not loosen, the installation is
complete. See Figure 4-14.

Figure 4-14 Installed SC fiber connector

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 207

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Step 4 To disassemble an SC fiber connector, hold the shell of the connector (do not hold
the fiber) and gently pull the connector in the direction vertical to the adapter.
Unlock the male connector, and then separate it from the shell, as shown in
Figure 4-15.

Figure 4-15 Disassembling an SC fiber connector

----End

4.1.2.3.4 Installing an MPO Connector

Procedure
Step 1 Remove the dustproof cap of the MPO fiber connector and store it for future use.
Step 2 Align the core pin of the male connector with that of the female connector, as
shown in Figure 4-16.

Figure 4-16 Aligning the male connector with the female connector

Step 3 Hold the shell labeled "PUSH" and feed the male connector into the female
connector until you hear a clicking sound. The male and female connectors are
securely installed, as shown in Figure 4-17.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 208

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Figure 4-17 Installed MPO fiber connector

Step 4 To disassemble an MPO fiber connector, hold the shell labeled "PULL" and remove
the male connector, as shown in Figure 4-18.

Figure 4-18 Disassembling an MPO fiber connector

----End

4.2 Appendix B Environmental Requirements for Device

Operation

4.2.1 Environmental Requirements for an Equipment Room

4.2.1.1 Requirements for Selecting a Site for an Equipment Room

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 209

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

When designing a project, consider the communication network planning and

technical requirements of the equipment. Also consider hydrographic, geological,
seismic, power supply, and transportation factors.
Construction, structure, heating and ventilation, power supply, lighting and fire-
proof construction of the equipment room should be designed by specialized
construction designers to suit the environmental requirements of devices. The
equipment room should also follow local regulations concerning the industrial
construction, environmental protection, fire safety, and civil air defense.
Construction must conform to government standards, regulations, and other
requirements.
The equipment room should be located in a place free from high temperature,
dust, toxic gases, explosive materials, or unstable voltage. Keep the equipment
room away from significant vibrations or loud noises, as well as power transformer
stations.
The specific requirements for selecting a site for an equipment room are as
follows:
● The room should be located at a distance of at least 5 km (3.11 mi.) from
heavy pollution sources such as smelting and coal mines. It should be located
at a distance of at least 3.7 km (2.30 mi.) from moderate pollution sources
such as chemical, rubber, and galvanization factories. It should be located at a
distance of at least 2 km (1.24 mi.) from light pollution sources such as
packinghouses and tanyards. If these pollution sources cannot be avoided,
ensure that the equipment room is upwind of the pollution sources. In
addition, use a high-quality equipment room or protection products.
● The room should be located away from livestock farms, or be upwind of the
livestock farms. Do not use an old livestock room or fertilizer warehouse as
the equipment room.
● The equipment room must be far away from residential areas. An equipment
room that is not far away from residential areas must comply with equipment
room construction standards to avoid noise pollution.
● The room should be located far away from industrial and heating boilers.
● The room should be at least 3.7 km (2.30 mi.) away from the seaside or salt
lake. Otherwise, the equipment room should be airtight with cooling facilities.
In addition, alkalized soil cannot be used as the construction material.
Otherwise, equipment suitable for wet conditions must be used.
● The doors and windows of the equipment room must be kept closed to
maintain an airtight room.
● Using steel doors to ensure sound insulation is recommended.
● No cracks or openings are allowed on the walls or floors. The outlet holes on
the walls or windows must be sealed. Walls must be constructed such that
they are smooth, wear-resistant, dustproof, flame retardant, sound insulated,
heat absorptive, and have electromagnetic shielding.
● The air vent of the room should be far from the exhaust of city waste pipes,
big cesspools and sewage treatment tanks. The room should be in the positive
pressure state to prevent corrosive gases from entering the equipment room
and corroding components and circuit boards.
● It is recommended that the room be on or above the second floor. If this
requirement cannot be met, the ground for equipment installation in the
room should be at least 600 mm (23.62 in.) above the maximum flood level.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 210

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

● The equipment room should be strong enough to resist winds and downpours.
● The room should be located away from dusty roads or sand. If this is
unavoidable, the doors and windows of the equipment room must not face
pollution sources.
● Do not place air conditioning vents near the equipment so that they blow
directly on the equipment because condensation may be blown into the
equipment.
● Do not use decorative materials that contain sulfur in the equipment room.

4.2.1.2 Equipment Room Layout

An equipment room usually contains mobile switching equipment,

telecommunications equipment, power supply equipment, and other auxiliary
equipment. To ensure easy maintenance and management, place the equipment
in different rooms. Figure 4-19 shows the layout of the equipment room.

Figure 4-19 Layout of the equipment room

The general layout principles of the equipment room are as follows:

● It should meet requirements for laying out and maintaining communication
cables and power cables.
● It should reduce the cabling distance, which facilitates cable maintenance,
reduces potential communication faults, and maximizes efficiency.
● To ensure normal operation of equipment in the equipment room when the
mains supply is disconnected, configure an emergency power generation
system for the equipment room.

4.2.1.3 Construction Requirements for the Equipment Room

Table 4-2 describes the construction requirements for the equipment room.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 211

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Table 4-2 Construction requirements for the equipment room

Item Requirements

Area The smallest area of the equipment room can accommodate the
equipment with the largest capacity.

Net height The minimum height of the equipment room should not be less
than 3 m (9.84 ft). The minimum height of the equipment room
is the net height below overhead beams or ventilation pipes.

Floor The floor in the equipment room should be semi-conductive and

dustproof. A raised floor with an ESD covering is recommended.
Cover the raised floor tightly and solidly. The horizontal
tolerance of each square meter should be less than 2 mm (0.08
in.). If raised floors are unavailable, use a static-electricity-
conductive floor material, with a volume resistivity of 1.0 x 107
ohms to 1.0 x 1010 ohms. Ground this floor material or raised
floor. You can connect them to ground using a one megohm
current-limiting resistor and connection line.

Load-bearing The floor must bear loads larger than 150 kg/m2 (0.21 bf/in.2).
capacity

Door and The door of the equipment room should be 2 m (6.56 ft) high
windows and 1 m (3.28 ft) wide. One door is enough. Seal the doors and
windows with dustproof plastic tape. Use double-pane glass in
the windows and seal them tightly.

Wall surface Paste wallpaper on the wall or apply flat paint. Do not use
treatment pulverized paint.

Cable trays Use cable trays to arrange cables. The inner faces of the cable
trays must be smooth. The reserved length and width of the
cable trays, and the number, position and dimensions of the
holes must comply with the requirements of device
arrangement.

Water pipe Do not pass service pipes, drainpipes, and storm sewers through
the equipment room. Do not place a fire hydrant in the
equipment room, but place it in the corridor or near the
staircase.

Internal Separate the area where the equipment is installed from the
partition wall equipment room door. The partition wall can block some outside
dust.

Installation Install air conditioner vents so that the air does not blow directly
position of on equipment.
the air
conditioner

Other Avoid the proliferation of mildew, and keep out rodents (like
requirements mice).

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 212

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Figure 4-20 Internal partition wall inside the equipment room

4.2.1.4 Equipment Room Environment

Dust on devices may cause electrostatic discharge and result in poor contact for
connectors or metal connection points. This problem can shorten the life span of
devices and cause faults.

The equipment room must be free from explosive, conductive, magnetically-

permeable, and corrosive dust. Table 4-3 lists the requirement for dust
concentration in the equipment room.

Table 4-3 Requirements for dust particles in the equipment room

Mechanical active Unit Concentration

material

Dust particle Particle /m3 ≤ 3x 104

(no visible dust
accumulated on a
workbench in three
days)

Suspending dust mg/m3 ≤0.2

Precipitable dust mg/m2·h ≤1.5

Description
● Dust particle diameter ≥ 5 µm
● Suspending dust diameter ≤ 75 µm
● 75 µm ≤ precipitable dust diameter ≤ 150 µm

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 213

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Take the following measures to meet the requirements:

● Use dustproof materials for ground, wall, and ceiling construction.
● Use screens on the door and windows facing outside. The outer windows
should be dust-proof.
● Clean the equipment room regularly and clean the air filter monthly.
● Wear shoe covers and ESD clothing before entering the equipment room.

4.2.1.5 Requirements for Corrosive Gases

The room should be free from dusts and corrosive gases, such as SO2, H2S, and
NH3. Table 4-4 lists the requirements for the corrosive gas concentration.

Table 4-4 Requirements for corrosive gas concentration

Chemical
active material Unit Concentration

SO2 mg/m3 ≤0.30

H2S mg/m3 ≤0.10

NOx mg/m3 ≤0.50

NH3 mg/m3 ≤1.00

Cl2 mg/m3 ≤0.10

HCl mg/m3 ≤0.10

HF mg/m3 ≤0.01

O3 mg/m3 ≤0.05

Take the following measures to meet the requirements:

● Avoid constructing the room near a place where the corrosive gas
concentration is high, such as a chemical plant.
● Ensure the air intake vent of the room is in the prevailing upwind direction
from any pollution source.
● Place batteries in different rooms.
● A professional service should monitor the corrosive gas conditions regularly.

4.2.1.6 Requirements for ESD Prevention

The absolute value of electrostatic voltage must be less than 1000 V.
Take the following measures to meet this requirement:
● Train operators about ESD prevention.
● Keep the correct humidity level in the equipment room to reduce the impact
of static electricity.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 214

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

● Lay out an ESD floor in equipment rooms.

● Wear ESD shoes and clothing before entering equipment room.
● Use ESD tools, such as wrist straps, tweezers, and pullers.
● Ground all conductive materials in the room, including computer terminals.
Use ESD worktables.
● Keep non-ESD materials (such as common bags, foam, and rubber) at least
30 cm (11.81 in.) away from boards and ESD-sensitive components.

4.2.1.7 Electromagnetism Requirements for the Equipment Room

All interference sources, inside or outside the equipment room, can cause
equipment problems with capacitive coupling, inductive coupling, electromagnetic
wave radiation, and common impedance (including grounding system) coupling.
Prevent the interference using these approaches:
● Take effective measures against electrical interference from the power supply
system.
● Do not use the working ground of the equipment as the same ground for
surge protection. Separate them as far as possible.
● Keep the equipment far away from high-power radio transmitters, radar units,
and high-frequency and high-current equipment.
● Use electromagnetic shielding if necessary.

4.2.1.8 Requirements for Lightning Proof Grounding

Table 4-5 lists the requirements for lightning proof grounding.

Table 4-5 Requirements for lightning proof grounding

Item Requirements

Capital ● Use reinforced concrete to construct the equipment room.

construction ● Install a lightning proof device like a lightning rod outside
the room.
● The lightning proof ground shares the same grounding
body with the protective ground of the room.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 215

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Item Requirements

Power cables ● After the low-voltage power cables are led into the room,
leading in the install the surge protector for the power cables in the AC
equipment voltage stabilizer and the AC power distribution panel
room need to (box). Correctly ground the surge protector nearby.
be equipped ● For an equipment room in urban area, install a power
with a surge supply surge protector with the nominal discharge current
protector of no less than 20 kA. For an equipment room that is built
in a suburb and subject to lightning strikes, install a power
supply surge protector with the nominal discharge current
of more than 60 kA. For an equipment room that is built in
a mountain area and subject to frequent lightning strikes,
or in a separate high-rise building in a city, install a power
supply surge protector with the nominal discharge current
of more than 100 kA.
● The ground cable of the surge protector should be no
longer than 1 m (3.28 ft).

Grounding for ● Connect the DC working ground (positive pole of the -48 V
DC power DC power supply or the negative pole of the 24 V DC power
distribution supply) with the indoor collective ground cable nearby. The
total ground cable should meet the maximum load of the
equipment.
● The power equipment must have a DC working ground
cable, which can connect the power equipment to the
collective ground cable of the telecommunication site (or
the protective ground bar of the equipment room).

Equipotential ● Properly ground the devices and auxiliary devices in the

connection room such as mobile base station, transmission, switching
equipment, power supply equipment, and cable distribution
frame. Connect all PGND cables to the collective protective
ground bar. Connect all PGND cables in one equipment
room to one protective ground bar.
● Apply joint grounding to the working ground and protective
ground of devices, which means the two share one
grounding network.
● The cable tray, rack or shell, metal ventilation pipe, metal
door or window of the equipment should be grounded for
protection.

General ● Do not connect the neutral line of the AC power cable with
requirements the protective ground of any telecom equipment in the
for grounding equipment room.
● Do not install a fuse or switch on the ground cable.
● All ground cables should be as short as possible, and
arranged in a straight line.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 216

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Item Requirements

Grounding ● The grounding resistance must be lower than 1 ohm.

resistance ● The upper end of the grounding body should be at least 0.7
m (2.30 ft) over the ground. In cold areas, bury the
grounding body below the frozen ground.
● Measure the grounding resistance periodically to ensure
effective grounding.

Routing of ● Do not arrange the signal cables overhead in the

signal cable equipment room. All signal cables must be led into the site
underground.
● Use the cables with a metal jacket or place them into a
metal pipe if they come out/in the equipment room.
● Ground the idle lines inside the cable in the equipment
room.
● Signal cables should be deployed on internal walls. Do not
deploy outdoor aerial cables.
● Keep signal cables away from power cables and surge
protection devices.

Collective ● Use a ground ring or ground bar for the collective ground
ground cable cable.
● Do not use aluminum cables as ground cables. Adopt
measures to prevent electrification corrosion when
connecting different metal parts together.
● Use a copper busbar as the collective ground cable with a
cross-sectional area of no less than 120 mm2 (0.19 in.2), or
use the galvanized flat steel of the same resistance. Insulate
the collective ground cable from the reinforcing steel bars
of the building.

Grounding The grounding lead-in should be a maximum of 30 m (98.42

lead-in ft) long. Use the galvanized flat steel with cross-sectional area
of 40 mm x 4 mm (1.58 in. x 0.158 in.) or 50 mm x 5 mm
(1.97 in. x 0.197 in.).

4.3 Appendix C Equipment Grounding Specifications

4.3.1 General Grounding Specifications

Table 4-6 shows the general grounding specifications.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 217

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Table 4-6 General grounding specifications

No. Description

1 The working ground and protective ground, including the shielded

ground and the lightning-proof ground of the cable distribution frame
should share the same grounding conductor.

2 The cable trays, shells, metal ventilation pipes, metal doors and windows
in the equipment room should be grounded for protection.

3 The metal parts of the equipment which are electrically floating in

normal conditions should be grounded for protection.

4 The ground cable must be connected securely to the protective ground

bar of the equipment room.

5 Do not use other equipment as part of the ground cable or electrical

connection.

4.3.2 Grounding Specifications for an Equipment Room

The grounding resistance of a comprehensive communication building should be
less than or equal to one ohm. The grounding resistance of an ordinary
communication office should be less than five ohms. The grounding resistance in
an area where the earth resistance rate is high should be less than 10 ohms.

4.3.3 Grounding Specifications for Signal Cables

Table 4-7 lists the grounding specifications for signal cables.

Table 4-7 Grounding specifications for signal cables

No. Description

1 Equip the cable outdoors with a metal jacket, well grounded at both
ends, or connect the ends of the metal jacket to the protective ground
bar of the equipment room. For cables inside the equipment room,
install surge protection devices at the interface to the equipment. The
PGND cable for the surge protection devices should be as short as
possible.

2 The incoming and outgoing signal cables to and from the office and
unused wires inside the cable should be grounded for protection.

3 The Tone & Data Access (TDA) cable must pass through the Main
Distribution Frame (MDF) with surge protective device (SPD) when
going out of the office. The cable's shield layer should be connected to
the protective ground of the MDF. The MDF should use the same
grounding conductor as the cabinet.

4 Do not route signal cables overhead.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 218

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

4.3.4 Specifications for Laying Out Grounding Cables

Table 4-8 shows the specifications for the ground cable.

Table 4-8 Specifications for laying out ground cables

No. Description

1 The grounding wire should not run parallel to or twist around the signal
cable.

2 Bury ground underground or arrange them indoors. Do not route ground

cables overhead.

3 Do not connect two cables together to extend the PGND cable, or add
any switches or fuses.

4 The PGND cable should be an alternating yellow and green plastic

insulated one with a copper core.

5 The neutral line of the AC power cable cannot be connected to the

protective ground of transmission and communication equipment in the
equipment room.

6 A PGND cable should be as short as possible, with a length of no more

than 45 m (147.64 ft).

4.4 Appendix D Engineering Labels for Cables

An engineering label serves as an identifier for on-site installation and
maintenance after the installation. Labels on the cables facilitate correct and
orderly connection of cables, and easy maintenance after installation.

Engineering labels are specialized for power cables and signal cables:
● Signal cables include network cables, optical fibers, and user cables.
● Power cables include the AC power cables and DC power cables.

NOTE

Fill in labels according to specified requirements to keep consistency of labels in the

equipment room. Make a relevant statement in the self-check report.

4.4.1 Engineering Labels for Optical Fibers

These labels are affixed to the optical fibers that connect the optical interfaces on
the boards in a chassis, or on the device boxes. There are two types of labels for
optical cables:
● One is for the fiber that connects the optical interfaces on two devices.
● The other is for the fiber that connects the device and the ODF.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 219

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

4.4.1.1 Labels for the Optical Fibers Connecting Devices

Meaning of the Label

Table 4-9 lists information on both sides of the labels affixed to the optical fibers
that connect two devices.

Table 4-9 Information on labels affixed to the fibers between two devices
Content Meaning Example

MN-B-C-D- MN: cabinet M: The cabinet rows from front to back are
R/T number numbered from A to Z.
N: The cabinet columns from left to right are
numbered from 01 to 99.
For example, A01 is the cabinet in row A and
column 01.

B: chassis Numbered in bottom-up order with two digits,

number for example, 01.

C: physical Numbered in top-down and left-right order

slot number starting from 01. For example, 01 is the first slot
at the top left of the chassis.

D: optical Numbered in top-down and left-right order,

interface consistent with the port sequence number on
number. the device.

R: Receiving -
interface
T: optical
transmitting
interface

Example of the Label

Figure 4-21 shows a sample label on an optical fiber.

Figure 4-21 Sample label on an optical fiber between two devices

The meaning of the label is listed in Figure 4-21.

● "A01-01-05-01-R" indicates that the local end of the optical fiber is connected
to the optical receiving interface 01 in slot 5, chassis 01 in the cabinet in row
A, column 01 in the machine room.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 220

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

● "G01-01-01-01-T" indicates that the opposite end of the optical fiber is

connected with optical transmitting interface 01 in slot 01, chassis 01 in the
cabinet in row G, column 01 in the machine room.

4.4.1.2 Labels for the Optical Fibers Connecting the Device and an ODF

Meaning of the Labels

Table 4-10 shows information on both sides of labels attached to an optical fiber
between a device and an optical distribution frame (ODF).

Table 4-10 Information on labels affixed to a fiber between a device and an ODF
Content Meaning Example

MN-B-C-D- MN: cabinet For example, A01.

R/T number

B: chassis Numbered in bottom-up order with two digits,

number for example, 01.

C: physical slot Numbered in top-down and left-right order

number starting from 01. For example, 01 is the first
slot at the top left of the chassis.

D: optical Numbered in top-down and left-right order,

interface consistent with the port sequence number on
number. the device.

R: Optical -
receiving
interface
T: optical
transmitting
interface

ODF-MN-B- MN: row M: The cabinet rows from front to back are
C-R/T number and numbered from A to Z.
column N: The cabinet columns from left to right are
number of an numbered from 01 to 99.
ODF
For example, G01 is the ODF of row G and
column 01.

B: row number Range from 01 to 99, for example, 01-01.

of the terminal
device

C: column
number of the
terminal
device

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 221

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Content Meaning Example

R: Optical -
receiving
interface
T: optical
transmitting
interface

Example of the Label

Figure 4-22 shows a sample label on an optical fiber.

Figure 4-22 Sample label on an optical fiber between the device and the ODF

Meaning of the label in Figure 4-22

● "ODF-G01-01-01-R" indicates that the local end of the optical fiber is
connected to the optical receiving terminal in row 01, column 01 of the ODF
in row G, column 01 in the machine room.
● "A01-01-05-01-R" indicates that the opposite end of the optical fiber is
connected to optical receiving interface 1 in slot 05, chassis 01 in the cabinet
in row A, column 01 in the machine room.

4.4.2 Engineering Labels for Network Cables

Applicable Ranges
The labels can be applied to Ethernet cables.

Label Content
Table 4-11 shows the information on both sides of the labels affixed to Ethernet
cables.
You can also decide the label content based on the actual environment. If the
device is not installed in the cabinet, for example, you can remove the cabinet
number.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 222

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Table 4-11 Information on the Ethernet cables

Content Meaning Example

MN-B-C-D MN: cabinet For example, A01 is the first cabinet in row A.
number

B: chassis Numbered in bottom-up order with two

number digits, for example, 01.

C: physical slot Numbered with two digits in top-down and

number left-right order. For example, 01.

D: network port Numbered in top-down and left-right orders.

number For example, 01.

MN-Z MN: cabinet For example, B02 is the second cabinet in

number row B.

Z: Location Fill in the location number of the terminal

number device on site. If the cable is connected to a
device in a cabinet, specify the serial
numbers of the cabinet, the chassis, and the
Ethernet interface of the device. For example,
B02-03-12. If the cable is connected to the
Network Management Station (NMS),
specify the specific location of the NMS.

The contents of the labels for network cables connecting hubs and devices or
agents and the network cables for other purposes should be specified according to
actual connections. The details are as follows:
● For a network cable connecting a hub and device, the label on the hub end
should indicate the numbers of the chassis and cabinet where the hub resides,
and the serial number on the hub. The label on the device end should indicate
the number of the chassis and cabinet where the device is located. If the
device is a standalone device, provide the specific position of the device.
● For a network cable connecting a hub and an agent or terminal, the label on
the agent or terminal end should contain the serial number of the network
interface. The definitions of the cabinet number and chassis number are the
same as those described in Table 4-11.
● If the hub is a standalone device without a cabinet or chassis, the label should
contain specific location information that identifies the hub.
The serial number on the hub, the network interface number of the agent or
terminal, and the location of the standalone device should be specified according
to actual connections.

Label Example
Figure 4-23 shows a sample label on an Ethernet cable.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 223

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Figure 4-23 Sample label on an Ethernet cable

Meaning of the label in Figure 4-23.

● "A01-03-01-01" indicates that one end of the network cable is connected to
network interface 01 in slot 01, chassis 03 of the cabinet in row A, column 01
in the equipment room.
● "B02-03-01" indicates that another end of the network cable is connected to
network interface 01 in chassis 03 of the cabinet on row B, column 02 in the
equipment room. No slot number is given.

4.4.3 Engineering Labels for User Cables

Attach labels to both ends of a user cable to indicate the locations of the cable on
the device and main distribution frame (MDF).

Meaning of the Engineering Labels for User Cables

Table 4-12 shows the contents of the labels.

Table 4-12 Contents of the engineering labels for user cables

Content Meaning Example

MN-B-C-D MN: cabinet For example, A01 is the first cabinet in row
number A.

B: frame Numbered in the bottom-up order with two

number digits, for example, 03.

C: physical slot Numbered with two digits in top-down and

number left-right order. For example, 01.

D: cable number Numbered with two digits in top-down and

left-right order. For example, 01.

MDF-MN-B-C MN: row M: The rows of cabinets from front to back

number and are numbered from A to Z. N: The columns
column number of cabinets from left to right are numbered
of the MDF from 01 to 99. For example, G01 is the MDF
of Row G and Column 01.

B: row number Ranges from 01 to 99, for example, 01-01.

of the terminal
device

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 224

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Content Meaning Example

C: column
number of the
terminal device

Example of the Label

Figure 4-24 shows a sample label on a user cable.

Figure 4-24 Sample label on a user cable

The meaning of the label in Figure 4-24 is as follows:

● "A01-03-01-01" indicates that the local end of the user cable is connected to
port 1 in slot 1, chassis 03 of the cabinet in row A, column 01 in the
equipment room.
● "MDF-G01-01-01" indicates that the opposite end of the user cable is
connected to the terminal in row 01, column 01 of the MDF in row G, column
01 in the equipment room.

4.4.4 Engineering Labels for Power Cables

4.4.4.1 Engineering Labels for DC Power Cables

These labels are affixed to the DC power cables that provide power supply for
cabinets, including the -48 V, PGND, and BGND cables. Here, the DC power cables
also include power cables and PGND cables.

The labels for DC power cables are affixed to one side of the identification plates
on cable ties. For details of the labels, see Table 4-13.

Table 4-13 Contents of the label

Content Meaning

MN(BC)- MN(BC): BC is written right under MN.

B--48Vn B: chassis number, numbered in bottom-up order with two
digits, for example, 01.
MN(BC)-B-
BGND N: power socket number, numbered as 1 to 3 in the bottom-
up and left-to-right orders.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 225

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Content Meaning

MN(BC)-B- On the loaded cabinet side, only MN is used to identify the

PGND cabinet.
On the power cabinet side, MN identifies the row and column
number of the power distribution equipment like a control
cabinet and distribution box, and BC identifies the row and
column number of the -48 V connector. If there is no row
number or column number, or the connector can be identified
without them, BC can be omitted. It is unnecessary to identify
the row and column number for BGND and PGND.

The label only carries location information about the destination direction of the
power cable whereas information about the local end is unnecessary. That is, the
label only carries location information about the opposite equipment, the control
cabinet, or the distribution box. Table 4-13 lists the information on two -48 V
power supplies on the label. The information on other DC voltages, such as 24 V
and 60 V should be given in similar methods.
Make sure that labels are affixed in the correct direction. That is, after the cable
ties are bundled onto the cable, the identification plates with the labels should
face up, and the text on the labels in the same cabinet should be in the same
direction. For details, see Figure 4-25.

Figure 4-25 Example of the labels for DC power cables

The meaning of the label in Figure 4-25 is as follows:

● On the loaded cabinet side, the label "A01/B08--48V2" on the cable indicates
that the cable is -48 V DC supply, which is from the eighth connector in row B
of -48 V bus bar in the cabinet in row A, and column 1 in the equipment
room.
● On the distribution box side, the label "B03--48V2" indicates that the cable is
-48 V DC supply, connected to DC power socket 2 in row B, column 03 in the
equipment room.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 226

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

NOTE

In the power distribution box or the first power cabinet of a row in a transmission
equipment room, every terminal block on the -48 V connector bar has a numeric
identification. For example, in the above label of "A01/B08--48V2", "08" (or sometimes "8")
is the numeric identification of the terminal block.

PGND and BGND are two copper bars, on which the terminal blocks are short-
circuited. Therefore, it makes no difference which terminal is connected to them. It
is only necessary to give the row and column of the power distribution box,
instead of giving the specific serial number of the terminal block on the copper
bar. For example, if the label on the loaded cabinet side is "A01-BGND", it means
that the power cable is a BGND that connects BGND copper bar in the power
distribution box in row A, column 01 in the machine room. Information on the
labels for PGND cables should be given in a similar way.

4.4.4.2 Engineering Labels for AC Power Cables

These labels are affixed to both ends of an AC power cable that provides AC
power supply to cabinets, including 110/220 V, PGND, and BGND cables. The
110/220 V AC cables and related PGND and BGND cables are covered with an
insulating sheath, so the labels need to contain only the word "AC" and the
cabinet numbers.
The labels for AC power cables are affixed to one side of the identification plates
on cable ties. For details, see Table 4-14.

Table 4-14 Label content

Content Meaning

MN-(B)-ACn MN: serial number of the cabinet or the socket where the
power is led in
B: chassis number, numbered in bottom-up order with two
digits, for example, 01.
n: power port number, numbered as 1 to 3 in bottom-up and
left-to-right order.
Serial number of the socket where the power is led in: the
location of the socket is marked according to the actual
situation. If the sockets can be identified by row numbers and
column numbers, they can be numbered following the same
rule for the cabinets. If the sockets cannot be identified by
rows and columns, specify the detailed locations to avoid
confusion with other sockets.

The label only carries location information about the opposite equipment and the
power socket; information about the local end is unnecessary.
Make sure that labels are affixed in the correct direction. That is, after the cable
ties are bundled onto the cable, the identification plates with the labels should
face up, and the text on the labels in the same cabinet should be in the same
direction, as shown in Figure 4-26.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 227

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Figure 4-26 Labels for AC power cables

Meaning of the label in Figure 4-26.

● On the equipment cabinet side, the label marked "A01-AC1" indicates that
the power cable is connected to the first AC power socket of row A and
column 01 in the equipment room.
● On the power socket side, the label marked "B01-AC1" indicates that the
power cable is connected to the first AC power socket in the cabinet of row B
and column 01 in the equipment room.

4.5 Appendix E Guide to Using Optical Modules

Common Faults of an Optical Module

1. An optical module is not completely installed in position.
If the optical module is not completely installed in position and the latch boss
is not secured, the device cannot identify the optical module. After the optical
module works for a long time, it will be ejected under external stress.
2. The optical receptacle on an optical module is contaminated.
If an optical module is not cleaned or protected properly, contaminants may
accumulate on the fiber pin in the optical module. As a result, the coupling
efficiency is reduced, optical signals are cut off, or even worse, the surface of
the fiber pin is damaged permanently.
3. An optical module is burnt.
If high-power optical signals (caused by an optical time domain reflectometer
or self-loop test) are transmitted through an optical module that is used for
long-distance transmission but no optical attenuator is used, the optical
power will exceed the overload power of the avalanche photodiode (APD).
Then the optical module is burnt.

The preceding faults lead to temporary or long-term cut-off of optical signals; or

even cause permanent damages to the optical module, affecting communication
services.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 228

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Measures to Prevent a Loosened Optical Module

1. When installing an optical module, insert it in position. If you hear a click or
feel a slight shake, it indicates that the latch boss is secured.
If the latch boss is not secured, the gold finger of the optical module is not in
good contact with the connector on the board. In this case, the link may be
connected but optical signals will be cut off or the optical module will be
loosened when the optical module is shaken or hit.
2. Figure 4-27 shows the release handle on an optical module when it is open
and closed. When inserting the optical module, make sure that the release
handle is closed. At this time, the latch boss locks the optical module. After
the optical module is inserted, try pulling it out to see if it is installed in
position. If the optical module cannot be pulled out, it is secured.

Figure 4-27 State of the release handle

Measures to Prevent Receptacle Contamination

1. Cleaning tissues must be prepared on site. You need to clean the optical
connector before inserting it in the receptacle. This protects the receptacle
against contamination on the surface of the optical connector.

Figure 4-28 Cleaning optical fibers with special cleaning tissues

NOTE

Place at least three cleaning tissues on the work bench. As shown in Figure 4-28, wipe
the end of an optical connector from left to right or from right to left on a cleaning
tissue, and then move the connector end to the unused part of the cleaning tissue to
continue.
2. Cover an unused optical module with a protective cap to prevent dust, as
shown in Figure 4-29.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 229

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Figure 4-29 Installing a protective cap

If no protective cap is available, use fibers to protect the optical module, as

shown in Figure 4-30.

Figure 4-30 Using fibers to protect an optical module

3. Cover unused optical connectors with protective caps, as shown in Figure

4-31, and then lay out fibers on the fiber rack or coil them in a fiber
management tray to prevent fibers from being squeezed.

Figure 4-31 Installing a protective cap on a fiber

4. If a receptacle or an optical connector has not been used for a long time and
is not covered with a protective cap, you need to clean it before using it. Clean
a receptacle with a cotton swab, as shown in Figure 4-32. Clean an optical
connector with cleaning tissues.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 230

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Figure 4-32 Cleaning a receptacle with a cotton swab

NOTICE

When cleaning a receptacle, insert the cotton swab and turn it slowly in the
receptacle. Do not use too much strength because the receptacle may be
damaged.

5. If optical signals are lost during the operation of a device, use the preceding
method to clean the receptacle or the optical connector. In this manner, the
possibility of contamination can be excluded.

Measures to Prevent an Optical Module from Being Burnt

1. Before using an optical time-domain reflectometer (OTDR) to test the
connectivity or the attenuation of optical signals, disconnect the optical fibers
from the optical module. Otherwise, the optical module will be burnt.
2. When performing a self-loop test, use an optical attenuator. Do not loosen
the optical connector instead of the optical attenuator.

Precautions
1. The optical connector should be vertically inserted in the receptacle to avoid
damages to the receptacle.
2. Fibers must be inserted into optical modules of the corresponding type. That
is, multimode fibers must be inserted into multimode optical modules, and
single mode fibers must be inserted into single mode optical modules. If a
fiber is inserted into an optical module of a different mode, faults may occur.
For example, optical signals will be lost.

4.6 Appendix F Fault Tag

*Customer name:

Address:

Contact person:

Tel.: Fax:

Category*: □ RMA □ Return □ Analysis

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 231

S200, S300, S500, S1700, S2700, S3700, S5700, and
S6700 Switches
Hardware Installation and Component Replacement 4 Appendix

Descripti
on of the
Product Fault Fault
BOM Descripti Bar Occurrin Phenome Category Software
Code on Code* g Date* na* No.* Version*

Reasons for Repairing (Category No.):

Category No. includes the following eight types:

F001 - Wear out damaged (◊ In warranty Period ◊ Out of warranty period)
F002 - Deployment damaged
F003 - Intransit damaged
F004 - Version upgrade
F005 - Batch replace
F007 - Overdue spare parts inspecting
F008 - Others
F011 - Running circumstance change

Note:
● For optical interface cards returned, the optical interfaces should be covered
with protection caps.
● In general, the analysis card will not be returned to you. If you have any
special requirements, please contact Huawei.
● One Fault Tag should be adapted in one return category, such as RMA/
Return/Analysis.
● The items marked with "*" are the mandatory fields that you must fill in.

Issue 30 (2023-03-30) Copyright © Huawei Technologies Co., Ltd. 232