ACD-V MULTI-CRITERIA SENSOR

APPLICATIONS
The Hochiki ACD-V Multi-Criteria Sensor is particularly suited
for detecting smoke produced by the wide range of combusti-
bles found in various applications. Temperature monitoring is
achieved by thermistors placed for optimum sensitivity. Also,
the sensor is suited for detecting deadly levels of carbon
monoxide (CO). Hochiki's unique design allows fast response
to flaming/smoldering fires and carbon monoxide levels while
minimizing nuisance alarms.
OPERATION
STANDARD FEATURES
To sense smoke, the ACD-V uses a light-emitting diode (LED)
 Low profile - only 2” high and photodiode compliment. The chamber is designed such
that light emitted by the LED cannot normally reach the
 Simple and reliable device addressing photodiode. In the event of fire, particles of smoke enter the
 Supports 16 operational modes chamber and scatter the light. As the smoke level increases,
the scattering effect increases, causing more light to hit the
 Automatic compensation for sensor contamination photodiode. The chamber contains a unique design which
allows smoke to enter the chamber while preventing external
 Built-in fire test feature light from affecting the photodiode. The photodiode input level
is sampled to sense smoke density. When the smoke density
 Uses the noise-immune Digital Communication Protocol exceeds a preset threshold the sensor transmits an interrupt
(DCP), which utilizes interrupts for fast response to fires to the fire control panel indicating a fire condition. The fire
 Two built-in power/alarm LEDs alarm control panel can adjust the sensor threshold to com-
pensate for contamination.
 Programmable non-polling LEDs The ACD-V heat portion incorporates a highly linear dual
 Non-directional smoke chamber thermistor circuit. A specially designed cover protects the
thermistors while allowing maximum air flow. The ACD-V
 Vandal resistant security locking feature supports both fixed-temperature and rate-of-rise sensing. The
fire alarm control panel can adjust the sensor threshold for
 10 years CO sensor life span* different environmental requirements.
SPECIFICATIONS The ACD-V carbon monoxide (CO) sensing cell serves the
dual purpose of supplementing smoke detection in combina-
tion with the photodiode arrangement and monitoring color-
Operating Voltage 17-41 VDC less, odorless and deadly carbon monoxide levels for life safe-
Standby Current 450μA ty. When the carbon monoxide exceeds the poisonous levels,
the sensor transmits an interrupt to the control panel indicat-
Alarm Current 7.2mA ing a CO alarm.
Transmission Method DCP - Digital Communication Protocol
Up to 127 devices are permitted on each SLC loop. A sensor
Maximum Humidity 95% RH Non-Condensing
address can be set by a hand-held programming unit. The
UL Temperature Range 32°F to 120°F sensor mounts to a base and incorporates a locking mecha-
(0° C to 49° C) nism for secure installation. The base provides mounting slots
Operating Temperature 14°F to 122°F and terminals for field wiring. The sensor incorporates dual
LEDs for easy viewing of sensor status.
Range (-10°C to 50°C)
Sensitivity Range 0.7-4.0%/FT@300FPM The ACD-V is fully compatible with today’s enhanced FireNET
Plus Controls and Loop Explorer II Software.
0.7-3.86%/FT@2000FPM
* Detectors must be replaced after 10 years from date of manufacturing.
0.7-2.65%/FT@4000FPM
Air Velocity Range 0-4000 fpm PRODUCT LISTINGS
Color & Case Material Bone - ABS Blend
Weight 4.2oz (5.9 oz. with 4” base) California State
Dimensions 3.9”D x 1.8”H Fire Marshal
Recommended Base ASBL 7275-0410:0503
S1383 3061300
Specifications subject to change without notice. Continued on back.

Hochiki America Corporation Find latest revision at www.hochiki.com

7051 Village Drive, Suite 100, Buena Park, CA 90621-2268
Phone: 714-522-2246 Fax: 714-522-2268
Technical Support: 800-845-6692 or [email protected] F0210 01/2018
 ACD-V MULTI-CRITERIA SENSOR
SENSOR SPACING
Smoke sensor spacing shall be in compliance with NFPA 72. For smooth ceilings and in the absence of specific performance-
based design criteria, the distance between smoke sensors shall not exceed a nominal spacing of 30 ft. (9.1m) or all points on the
ceiling shall have a sensor within a distance equal to or less than 0.7 times the nominal 30 ft. (9.1m) spacing. Sensors shall be
located within a distance of one-half the nominal spacing, measured at right angles from all walls or partitions extending upward
to within the top 15 percent of the ceiling height. For additional instructions see NFPA 72.
ENGINEERING SPECIFICATIONS
The contractor shall furnish and install Hochiki's ACD-V (Multi-Criteria Sensor) as indicated on the plans. The Multi-Criteria
Sensor head and twist lock base is UL Listed and it’s compatible with an UL Listed fire alarm control panel.
The base permits direct interchange with the Hochiki ALG-V, ALK-V/ALK-V2, ALN-V photoelectric type smoke sensors, AIE-EA
ionization type smoke sensor, ATG-EA, ATJ-EA heat sensors and the ACA-V, ACC-V multi-criteria sensor.
The sensitivity of the sensor is capable of being measured by the control panel. The CO sensing element shall provide for 10
years of active usage.
The vandal-resistant, security locking feature shall be used in those areas as indicated on the drawing. The locking feature is
optional and can be implemented when required.
BASES
The ACD-V supports the YBN-NSA-4, HSB-NSA-6, ASBL, SCI-B4, SCI-B6 bases as well as the recommended ASBL base when
used for life safety CO sensing. A common mounting base allows sensor interchange and maintains loop continuity when sen-
sors are removed. A simple anti-tamper head locking system is provided which is enabled by removing a small plastic tab on the
back of the sensor. Once locked, the head can be removed using a small diameter screwdriver

TYPICAL WIRING DIAGRAMS

NOTE: Fire alarm control panel compatibility is required for DCP products. DCP communications protocol allows system compo-
nents (DCP sensors AIE-EA, ALG-V, ACA-V, ACC-V, ALK-V, ALN-V, ATJ-EA, ATG-EA, ACD-V, bases and modules) to be used
concurrently on a system's SLC (Signaling Line Circuit).

Hochiki America Corporation ACD-V Multi-Criteria Sensor Specifications subject to change without notice.