Distributed by:

www.Jameco.com ✦ 1-800-831-4242
The content and copyrights of the attached
material are the property of its owner.

Jameco Part Number 1773241

 150 Watts Total Power: 110-150 Watts
Input Voltage: 85-132 / 170-264 VAC
220-300 VDC

LPQ150 Series # of Outputs: Quad

Electrical Specs
Input
Input range 85-132 VAC or 170-264 VAC automati-
cally selected. 220-300 VDC
Frequency 47-63 Hz
Inrush current 38 A max, cold start @ 25°C
Efficiency 75% typical at full load
EMI filter Meets FCC Class B conducted
CISPR 22 Class B conducted
EN55022 Class B conducted
VDE 0878 PT3 Class B conducted
Safety ground leakage
current 0.5 mA @ 50/60 Hz, 264 VAC input

Special Features Output

• Auto ranging input Maximum power 110 W convection (75 W with cover)
• Remote sense on main output 150 W with 30 CFM forced air
• Remote inhibit (130 W with cover)
• Single wire current sharing Adjustment range ±5% on main; 5-25 V on 4th output
• Power fail on LPQ 152 & LPQ 153
• Built-in EMI filter Cross regulation ±2% on output 1; ±3% on outputs 2, 3
• Low output ripple &4
• 135 khz switching frequency Hold-up time 20 ms @110 W load at nominal line
• Overvoltage protection
Overload protection Short circuit protection on all outputs.
• Overload protection
Case overload protected @ 110-145%
• Adjustable floating 4th output
above peak rating
(On LPQ152 and LPQ153 models)
• Optional cover (-C suffix). See page 64. Overvoltage protection 5.7-6.7 VDC on main output

Environmental Logic Control

Power failure TTL logic signal goes high 50-150
Operating temperature: 0° to 50°C ambient msec after 5 V output. It goes low at
derate each output at 2.5% per degree from least 3 msec before loss of regulation
50° to 70°C Remote inhibit Requires an external TTL high signal to
inhibit outputs
Electromagnetic susceptibility: designed to meet
IEC 801, -2, -3, -4, -5, -6, Level 3 Remote sense Compensates for 0.5 V lead drop min.
Will operate without remote sense
Humidity: Operating; non-condensing connected. Reverse connection
5% to 95% protected.
Vibration: Three orthogonal axes, sweep at
1 oct/min, 5 min. dwell at four major resonances
0.75 G peak 5 Hz to 500 Hz, operational Safety
Storage temperature: -40° to 85°C
VDE 0805/EN60950 (IEC950) 11774-3336-1260 (LC# 88585)
Temperature coefficient: ± .04% per °C UL UL1950 EI32002
MTBF demonstrated: >550,000 hours at full load CSA CSA 22.2-234 Level 3 LR53982
and 25°C ambient condition NEMKO EN 60950/EMKO-TUE P95102999
(74-sec) 203
CB Certificate and report 2061
CE Mark (LVD) rev 12.10.03

Technical Support: (888) 41-ASTEC or (407) 241-2752

114 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662
 AMERICAS EUROPE ASIA

5810 Van Allen Way Astec House, Waterfront Business Park Units 2111-2116, Level 21
Carlsbad, CA 92008 Merry Hill, Dudley Tower1, Metroplaza
Telephone: 760-930-4600 West Midlands, DY5 1LX, UK 223, Hing Fong Road
Facsimile: 760-930-0698 Telephone: 44 (1384) 842-211 Fwai Fong, New Territories
Facsimile: 44 (1384) 843-355 Hong Kong
Telephone: 852-2437-9662
Facsimile: 852-2402-4426

LPQ150 Series
Ordering Information
Model Output Minimum Maximum Load with Maximum Load with Peak Regulation2 Ripple
Number Voltage Load Convection Cooling 30 CFM Forced Air Load1 P/P (PARD)3

LPQ152 5V 2A 15 A 22 A 30 A ±2% 50 mV
12 V .1 A 6A 8A 10 A ±3% 120 mV
-12 V .1 A 2A 2.5 A 3A ±3% 120 mV
±5-25 V 0A 2.5 A 3A 3A ±3% 240 mV, max.

LPQ153 5V 2A 15 A 22 A 30 A ±2% 50 mV
15 V .1 A 4.8 A 6.4 A 8A ±3% 150 mV
-15 V .1 A 1.6 A 2A 2.4 A ±3% 150 mV
±5-25 V 0A 2.5 A 3A 3A ±3% 240 mV, max.

LPQ154 5V 2A 15 A 22 A 30 A ±2% 50 mV
12 V .1 A 6A 8A 10 A ±3% 120 mV
-12 V .1 A 2A 2.5 A 3A ±3% 120 mV
24 V .5 A 3.5 A 4.5 A 5A +10 / -5% 240 mV

1. Peak current lasting <30 seconds with a maximum 10% duty cycle.
2. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a 0.1 µF capacitor at rated line voltage and load ranges.
4. 4th output adjustable 5-25 V factory set at 5 V.
5. Minimum loads are required.
Note: -C suffix added to the model number indicates cover option.

DO NOT ADJ
SK1

Pin Assignments SK2

8765
#6-32 UNC (8 places)
SK3 1234 .5625
Connector LPQ152 LPQ153 LPQ154 2 1 987654321
SK1 PIN 1 INHIBIT -ve INHIBIT -ve INHIBIT -ve
PIN 2 INHIBIT +ve INHIBIT +ve INHIBIT +ve
PIN 3 +12 V +15 V +12 V
PIN 4 No Connection No Connection No Connection
PIN 5 COMMON COMMON COMMON
4th O/P ADJ

PIN 6 -SENSE -SENSE -SENSE

5V O/P ADJ

PIN 7 +SENSE +SENSE +SENSE

PIN 8 I SHARE I SHARE I SHARE
SK2 PIN 1,2 +12 V +15 V +12 V
PIN 3,4,5 COMMON COMMON COMMON
PIN 6 -12 V -15 V -12 V 7.4
PIN 7 POK POK POK (188.0)
PIN 8 +5 V to +25 V (Float) +5 V to +25 V (Float) +24 V
PIN 9 COMMON (Float) COMMON (Float) COMMON 8.5
SK3 TB-1 COMMON COMMON COMMON (216.0)
TB-2 +5 V +5 V +5 V
SK4 PIN 1 GROUND GROUND GROUND
PIN 3 LINE LINE LINE
PIN 5 NEUTRAL NEUTRAL NEUTRAL
Notes
Mating Connectors 1. Specifications subject to change
(SK4) AC Input: Molex 09-50-8051 (USA) without notice.
Molex 09-91-0500 (UK)
2. All dimensions in inches (mm), 531
PINS: 08-58-0111
tolerance is ±0.02”. .75 (19.0)
(SK2) Aux DC Output/Power fail: 3. Specifications are for convection SK4 1.5
Molex 09-50-8091 (USA) rating at factory settings unless 4.25 (38.1)
Molex 09-91-0900 (UK) otherwise stated. (108.0)
PINS: 08-58-0111 4. Remote inhibit requires an external
5V @ 10mA to activate.
(SK1) Remote sense/Remote inhibit: 5. Mounting (6-32) maximum insertion
Molex 51110-0851 (USA) depth is 0.12”.
PINS: 503-94-8100 6. Warranty: 1 year
7. Weight: 1.75 lb. / 0.80 kg
.875 2.5
(22.25) (63.5)
Astec Connector Kit #70-841-010, includes al of the above.

www.astecpower.com

115