Scribd
Upload
142 views6 pages

Bosch MEVD1728 ECU Connection Guide

This document provides instructions for connecting diagnostic equipment to read and program Bosch ECUs, including using a GPT connection, connecting power and boot wires, and positioning the ECU in a mounting frame. It warns to mark connector positions before removing the ECU and notes that the GPT connection requires using both analog and digital ports with specified wires. Diagrams show the ECU, cables, and connection points.

Uploaded by

maoyuhui
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
142 views6 pages

Bosch MEVD1728 ECU Connection Guide

This document provides instructions for connecting diagnostic equipment to read and program Bosch ECUs, including using a GPT connection, connecting power and boot wires, and positioning the ECU in a mounting frame. It warns to mark connector positions before removing the ECU and notes that the GPT connection requires using both analog and digital ports with specified wires. Diagrams show the ECU, cables, and connection points.

Uploaded by

maoyuhui
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

BOSCH_MEVD1728_IROM_TC1797_GPT_BMWVER 02.

05

NEW TRASDATA
PLUGIN 679  BOSCH MEDV1725/MEVD1728/MEDV1729 TC1797 GPT BMW
PLUGIN 879  BOSCH MEVD17.2.9 IROM TC1797 GPT BMW

WARNING: before extracting the ECU from the car mark the position of each connector.
When you set back the ECU into the vehicle make sure that all the connectors are
plugged in the correct position.

GPT CONNECTION MODE


To perform the GPT connection it is necessary to use both the ANALOG PORT and the DIGITAL
PORT.

GPT connection with loose wires


Connect the F32GN037 cable to the ANALOG PORT
Connect the F34NTA15 to the DIGITAL PORT, use the YELLOW and ORANGE wires ONLY for the
GPT signals, the WHITE and GREEN wires are for the second CAN line as displayed in the following
pictures.

F34NTA15

Dimsport s.r.l –15020 Serralunga di Crea (AL) - Italy- Tel. +39014295201 – WEB : www.dimsport.com -1-
BOSCH_MEVD1728_IROM_TC1797_GPT_BMWVER 02.05

MEVD1728

Dimsport s.r.l –15020 Serralunga di Crea (AL) - Italy- Tel. +39014295201 – WEB : www.dimsport.com -2-
BOSCH_MEVD1728_IROM_TC1797_GPT_BMWVER 02.05

Dimsport s.r.l –15020 Serralunga di Crea (AL) - Italy- Tel. +39014295201 – WEB : www.dimsport.com -3-
BOSCH_MEVD1728_IROM_TC1797_GPT_BMWVER 02.05

ECU CONNECTOR
For the connection use the cable F32GN037C connected to the ECU.
Make sure that the POWER led (red) on NEW TRASDATA is ON.
Warning: to connect the second CAN line use the WHITE and GREEN wires of the F34NTA15 flat
cable.

GPT DIRECT CONNECTION


GPT connection is required for the first time only, after the first ECU reading it is not necessary
any longer. Connect the F34NTA15 flat cable to the GPT_S1 & GPT_S2 pins.

To the power feeding pins 1,22,40 (+12V) you can connect both wires red (VECU) and orange
VKEY) of the F32GN037C cable, they both have 12V signal.

Dimsport s.r.l –15020 Serralunga di Crea (AL) - Italy- Tel. +39014295201 – WEB : www.dimsport.com -4-
BOSCH_MEVD1728_IROM_TC1797_GPT_BMWVER 02.05

DIRECT BOOT CONNECTION


Connect the GREY wire of the cable F32GN037C as shown in the picture.

Dimsport s.r.l –15020 Serralunga di Crea (AL) - Italy- Tel. +39014295201 – WEB : www.dimsport.com -5-
BOSCH_MEVD1728_IROM_TC1797_GPT_BMWVER 02.05

BNP POSITIONING FRAME CONNECTION

Dimsport s.r.l –15020 Serralunga di Crea (AL) - Italy- Tel. +39014295201 – WEB : www.dimsport.com -6-

You might also like